Cellular network
A cellular radio network is a radio network which uses a number of fixed transmitters to cover different areas in order to provide radio coverage over a wider area than the area of one cell. Cellular networks are inherently asymmetric with a set of fixed main transceivers each serving a cell and a set of distributed (generally, but not always, mobile) transceivers which provide services to the network's users.
Cellular networks offer a number of advantages over the alternative solutions,
- increased capacity
- reduced power usage
- better coverage
A good (and simple) example of a cellular system is an old taxi driver's radio system where a city will have several transmitters based around a city. We'll use that as an example and assume that each transmitter is handled separately by a different operator.
general characteristics
the primary requirement for a cellular network is a way for the distributed stations to distinguish the signal from it's own transmitter from the signal from other transmitters. There are two common solutions to this, FDMA and CDMA. FDMA works by using a different frequency for each neighbouring cell. By tuning to the frequency of a chosen cell the distribute stations can avoid the signal from other neighbours. The principle of CDMA is more complex, but achieves the same result; the distributed transceivers can select one cell and listen to it. Other available methods of multiplexing (e.g. PDMA and TDMA) cannot be used to separate signals from one cell to the next since the effects of both vary with position and this would make signal separation practically impossible. TDMA, however, is definitely used in a number of systems to give multiple channels within the coverage area of a single cell.
In the case of our taxi company, each radio has a knob. The knob acts as a channel selector and allows the radio to tune to different frequencies. As the drivers move around, they change from channel to channel. The drivers know which frequency covers approximately what area, when they don't get a signal from the transmitter, they also try other channels until they find one which works. The taxi drivers only speak one at a time, as invited by the operator (in a sense TDMA).
broadcast messages and paging
Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles, commonly the most important use of broadcast information is to
Our taxi network is a very good example here. The broadcast capability is often used to tell about road conditions and also to tell about work which is available to anybody. On the other hand, typically there is a list of taxis waiting for work. When a particular taxi comes up for work, the operator will call their number over the air. The taxi driver acknowledges that they are listening, then the operator reads out the address where the taxi driver has to go.
frequency reuse
The increased capacity in a cellular network, as compared to a network with a single transmitter, comes from the fact that the same radio frequency can be reused in a different area for a completely different transmission. If there is a single plain transmitter, only one transmission can be used on any given frequency. Unfortunately, there is inevitably some level of interference from the signal from the other cells which use the same frequency. This means that, in a standard FDMA system, there must be at least a one cell gap between cells which reuse the same frequency.
The frequency reuse factor is the rate at which the same frequency can be used in the network. It is 1/n where n is the number of cells which cannot use a frequency for transmission.
CDMA uses wider frequency band to achieve the same rate of transmission as FDMA, but this is compensated for by the ability to use a frequency reuse factor of 1. In other words, every cell uses the same frequency and the different systems are separated by codes rather than frequencies.
Depending on the size of the city, a taxi system may not have any frequency reuse in its own city, but certainly in other nearby cities, the same frequency can be used. In a big city, on the other hand, frequency reuse could certainly be in use. This
movement from cell to cell and handover
The use of multiple cells means that, if the distributed transceivers are mobile and moving from place to place, they also have to change from cell to cell. The mechanism for this has differ depending on the type of network and the circumstances of the change. For example, if there is an ongoing continuous communication and we don't want to interrupt, then great care must be taken if we want to avoid interrupting it. In this case there must be clear coordination between the base station and the mobile station. Typically such systems use some kind of multiple access independently in each cell, so an early stage of such a handover is to reserve a new channel for the mobile station on the new base station which will serve it. The mobile then moves from the channel on it's current base station to the new channel and from that point on communication takes place
The exact details of the mobile system's move from one base station to the other varies considerably from system to system. E.g. in all GSM handovers and WCDMA inter-frequency handovers the mobile station will measure the channel it is meant to start using before moving over. In IS-95 and WCDMA same frequency handovers, both channels will actually be in use at the same time (this is called a soft handover). In IS-95 inter-frequency handovers and older analog systems such as NMT it will typically be impossible to directly measure the target channel directly whilst communicating. In this case other techniques have to be used such a pilot beacons in IS-95. This means that there is almost always a brief break in the communication whilst searching for the new channel followed by a risk of an unexpected return to the old channel.
If there is no ongoing communication or the communication can be interrupted, it is possible for the mobile station to spontaneously move from one cell to another and then notify the network if needed.
In the case of a the primitive taxi system that we are studying, handovers won't really be implemented. The taxi driver just moves from one frequency to another as needed. If a specific communication gets interrupted due to a loss of a signal then the taxi driver asks the controller to repeat the message. If one single taxi driver misses a particular broadcast message (e.g. a request for drivers in a particular area), the others will respond instead. If nobody responds, the operator keeps repeating the request.
cell coverage area
The ideal cellular network shown in textbooks has hexagonal cells evenly spread out across the page. This might be approached in reality in a perfectly flat area with no buildings or other objects but it would be a rare system which would want to cover such an area. In practise, cell coverage varies considerably according to the terrain, the siting of the cell's antenna, intervening buildings, landmarks and barriers.
The other factor which influences cell coverage considerably is the frequency of the radio signal used. Simply put, lower frequencies tend to penetrate through obstacles well, whilst higher frequencies tend to be stopped by thin objects. For example, a five millimetre plaster board wall will completely stop light, but will have almost no noticeable effect on radio waves.
The effect of frequency on cell coverage means that different frequencies serve better for different uses. Low frequencies, such as 450 MHz NMT, serve very well for countryside coverage. GSM 900 (900MHz) is a suitable solution for light urban coverage. GSM 1800 (1.8 GHz) starts to be seriously limited by walls. This is a disadvantage when it comes to coverage, but it is a serious advantage when it comes to capacity. Pico cells, covering e.g. one floor of a building, become possible, and the same frequency can be used for cells which are practically neighbours. UMTS, at 2.1 GHz is quite similar in coverage to GSM 1800.
Moving beyond these ranges, network capacity generally increases (more bandwidth is available) but the coverage becomes limited to line of sight.
Old fashioned taxi radio systems, such as the one we have been studying, generally use low frequencies and high sited transmitters, probably based where the local radio station has its mast.