Beruflich Dokumente
Kultur Dokumente
Acson
Acson
N.M.S.
STOCK N° 4.048.462/Ed.3/08.00
FRANCAIS DEUTSCH
DÉCLARATION ”CE” DE CONFORMITÉ EG-ERKLÄRUNG ZUR KONFORMITÄT MIT DER
AUX DIRECTIVES ”BASSE TENSION” RICHTLINIE ”NIEDERSPANNUNG” und
& ”COMPATIBILITÉ ÉLECTROMAGNÉTIQUE” ”ELEKTROMAGNETISCHE VERTRÄGLICHKEIT”
Die Firma POMPES SALMSON erklärt, daß die in diesem vorliegenden bezeichneten
POMPES SALMSON déclare que les matériels désignés dans la présente Ausrüstungen die Bestimmungen der abgeänderten Richtlinie "NIEDERSPANNUNG"
notice sont conformes aux dispositions des directives ”BASSE TENSION” (EG-Richtlinie 73/23) sowie die Bestimmungen der abgeänderten Richtlinie
modifiée (Directive 73/23/CEE) et ”COMPATIBILITÉ ÉLECTROMAGNÉTIQUE” "ELEKTROMAGNETISCHE VERTRÄGLICHKEIT" (EG-Richtlinie 89/336) sowie die
modifiée (Directive 89/336/CEE) et aux législations nationales les transposant. nationalen Vorschriften, in denen diese Richtlinien umgesetzt werden, einhalten. Sie
Ils sont également conformes aux dispositions du projet et des normes euro- stimmen ferner mit den Bestimmungen des folgenden Entwurfs und der folgenden
vereinheitlichten europäischen Normen überein:
péennes harmonisées suivantes :
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
ENGLISH DANKS
EC DECLARATION OF COMPLIANCE WITH ERKLÆRING OM OVERENSSTEMMELSE MED EF’s
THE "LOW VOLTAGE" & "ELECTROMAGNETIC “LAVSPÆNDINGSDIREKTIV” og
COMPATIBILITY" DIRECTIVES “ELEKTROMAGNETISK KOMPATIBILITETSDIREKTIV”
POMPES SALMSON declares that the equipment described in this manual POMPES SALMSON erklærer, at udstyret, der beskrives i dette brugsanvisning,
complies with the provisions of the modified ”LOW VOLTAGE” directive er i overensstemmelse med bestemmelserne i det ændrede “LAVSPÆNDING-
(Directive 73/23/EEC) and with the modified "ELECTROMAGNETIC COMPATI- SDIREKTIV” (Direktiv 73/23/EØF) og det ændrede “ELEKTROMAGNETISK
KOMPATIBILITETSDIREKTIV” (Direktiv 89/336/EØF) samt de nationale
BILITY" directive (Directive 89/336/EEC) and with national enabling legislation lovgivninger, der indfØrer dem. Det er ligeledes i overensstemmelse med
based upon them. It also complies with the provisions of the following European bestemmelserne i fØlgende forslag og harmoniserede europæiske standarder:
standards and draft standards:
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
ITALIANO NEDERLANDS
DICHIARAZIONE DI CONFORMITA' "CE" "EG" VERKLARING VAN CONFORMITEIT
ALLA DIRETTIVA "BASSA TENSIONE" MET DE RICHTLIJN "LAAGSPANNING" EN
& "COMPATIBILITA' ELETTROMAGNETICA" "ELEKTROMAGNETISCHE COMPATIBILITEIT"
La ditta POMPES SALMSON dichiara che i materiali descritti nel presente POMPES SALMSON verklaart dat het in deze document vermelde materieel
manuale rispondono alle disposizioni delle direttive "BASSA TENSIONE" modi- voldoet aan de bepalingen van de gewijzigde richtlijnen "LAAGSPANNING"
ficate (Direttiva 73/23/CEE) e "COMPATIBILITA' ELETTROMAGNETICA" modi- (Richtlijn 73/23/EEG) en "ELEKTROMAGNETISCHE COMPATIBILITEIT"
ficata (Direttiva 89/336/CEE) nonché alle legislazioni nazionali che le transpon- (Richtlijn 89/336/EEG) evenals aan de nationale wetgevingen waarin deze
bepalingen zijn overgenomen. Het materieel voldoet eveneens aan de
gono. Sono pure conformi alle disposizioni del seguente progetto e delle seguen-
bepalingen van de ontwerp-norm en de Europese normen:
ti norme europee armonizzate:
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
ESPAÑOL ∂§§∏¡π∫A
DECLARACIÓN "C.E." DE CONFORMIDAD CON ¢∏§ø™∏ ¶I™∆√∆∏∆∞™ ”EK” ¶ƒ√™ ∆∏¡
LAS DIRECTIVAS "BAJA TENSION" Y O¢∏°I∞ ™ÃE∆πCA ME TI™ ”XAMH§H TA™H”
"COMPATIBILIDAD ELECTROMAGNÉTICA" & ”∆∏¡ ∏§EKTPOMA°NHTIKH ™YMBATOTHTA”
H POMPES SALMSON ‰ËÁÒvÂÈ fiÙÈ ÔÈ ÂÍÔÁÈÛÌÔ› Ô˘ ·Ó·Ê¤ÚÔÓÙ·È fiÙÔÓ
POMPES SALMSON declara que los materiales citados en el presente folleto ·ÚfiÓ٠ηٿÁÔÁÔ Â›Ó·È Û‡ÌʈÓÔÈ Ì ÙȘ ‰È·Ù¿ÍÂȘ Ù˘ ÙÚÔÔÈË̤Ó˘ Ô‰ËÁ›·˜
están conformes con las disposiciones de la directiva "BAJA TENSION" modifi- Û¯ÂÙÈο ÌÂÙȘ ”XAMH§H TA™H” (O‰ËÁ›· 89/392/EOK) Î·È Ù˘ ÙÚÔÔÔÈË̤Ó˘
cada (Directiva 73/23/CEE) y "COMPATIBILIDAD ELECTROMAGNÉTICA" Ô‰ËÁ›·˜ Û¯ÂÙÈο Ì ÙËÓ ”∆∏¡ ∏§EKTPOMA°NHTIKH ™YMBATOTHTA”
modificada (Directiva 89/336/CEE) y a las legislaciones nacionales que les son (O‰ËÁ›· 89/336/EOK) ηıÒ˜ Î·È Ì ÙȘ ÂıÓÈΤ˜ ÓÔÌÔıÂۛ˜ Ô˘ ÂÍ·ÛÊ·Á›˙Ô‡Ó
aplicables. También están conformes con las disposiciones del proyecto y de ÙËÓ ÚÔÛ·ÚÌÔÁ‹ ÙÔ˘˜. ∂›Ó·È ›Û˘ Û‡ÌʈÓÔÈ Ì ÙȘ ‰È·Ù¿ÍÂȘ ÙÔ˘ ۯ‰›Ô˘ ηÈ
las siguientes normas europeas armonizadas: ÙˆÓ ·ÎfiÁÔ˘ıˆÓ ÂÓ·ÚÌÔÓÈÛÌ¤ÓˆÓ Â˘Úˆ·˚ÎÒÓ ÚÔÙ‡ˆÓ :
EN 60730-2-6 / EN 50.081-1 y 2 / EN 50.082-1 y 2. EN 60730-2-6 / EN 50.081-1 & 2 / EN 50.082-1 & 2.
PORTUGUÊS
DECLARAÇÃO "C.E." DE CONFORMIDADE QUALITY MANAGEMENT
COM AS DIRECTIVAS "BAIXA TENSÃO"
E COMPATIBILIDADE ELECTROMAGNÉTICA
POMPES SALMSON declara que os materiais designados no presente catálogo
obedecem às disposições da directiva "BAIXA TENSÃO", modificada (Directiva Robert DODANE
73/23/CEE) e "COMPATIBILIDADE ELECTROMAGNÉTICA" (Directiva
89/336/CEE) e às legislações nacionais que as transcrevem. Obedecem
igualmente às disposições do projecto e das normas europeias harmonizadas
seguintes:
EN 60730-2-6 / EN 50.081-1 e 2 / EN 50.082-1 e 2.
2
FIG. 1 6 FIG. 3
5
3
220-240 V L1
2 50 - 60 Hz
N
12
1 M U
1
13 V
4 8 10 11 9
FIG. 2 1x220-240 V
0
1
HR
; ;;
;
HC
1x220-240 V
; ;; ;;;
ou/or
; ;; ;;;
;;; ;;;
;;
3-380/400 V
FIG. 4 50 - 60 Hz
220-240 V FIG. 5
50 - 60 Hz
L1 L2 L3 N
L1
N
U-V : 220/240 V
50 / 60 Hz U
10A MAX.
V
7
3
FRANCAIS
Cet automatisme peut fonctionner de la même façon avec des cir- 3 - Manomètre (0 - 10 bars) de contrôle.
cuits d’eau potable ou non potable. Dans le cas d’installation ou l’on (montage possible à droite ou à gauche).
peut utiliser les deux genres d’eau, il faudra s’assurer que le circuit
4 - boîtier électrique avec platine électronique intégrant une
d’eau potable n’entrera jamais en contact avec celui d’eau non
protection manque d’eau par arrêt du moteur et boîtier de
potable.
raccordement pompe et réseau.
1.2 Caractéristiques techniques
5 - Chambre hydraulique avec membrane.
• Liquide véhiculé : eau claire
6 - Chambre de compensation avec ressort.
• Débit maxi : 10 m3/h
7 - Vis de réglage de la pression d’enclenchement de la
• Pression de service maxi : 10 bars
pompe.
• Plage de température : 0° à + 60° C
8 - bouton de réarmement (RESET).
• Pression d’enclenchement pompe : 1,5 à 3 bars
9 - Indicateur lumineux de tension (POWER).
• Tension d’alimentation mono : 220-240 V
10 - indicateur lumineux de fonctionnement de la pompe (ON).
• Fréquence : 50 Hz - 60 Hz
11 - Indicateur lumineux d’activation du système de sécurité
• Intensité maxi : 10A
(ALARM).
• Indice de protection : IP 65
12 - Couvercle inférieur
13 - Axe du manomètre.
2. SÉCURITÉ
4.2 Principe de fonctionnement
La présente notice devra être lue avec attention avant installation et
mise en service. On veillera en particulier, au respect des points Dès l’ouverture d’un robinet, la pression dans l’installation chute et la
concernant la sécurité du matériel vis à vis de l’utilisateur pompe démarre instantanément au seuil de 1,5 bar pré-réglé en
intermédiaire ou final. usine (réglage jusqu’à 3 bars possible sur le site).
Le fonctionnement de la pompe dure tant qu’un débit minimum sub-
2.1 Symboles des consignes du manuel
siste dans le réseau.
A la fermeture du robinet, la pompe s’arrête automatiquement
Signale un risque potentiel, mettant en danger la sécurité des
après une temporisation de quelques secondes. L’automatisme pro-
personnes.
tège la pompe contre le manque d’eau par arrêt du moteur. Cet
arrêt est signalé par l’allumage du témoin lumineux ”ALARM”.
Consignes de sécurité relatives à l’électricité.
Remise en route de la pompe par touche ”RESET”.
4
FRANCAIS
Selon l’orientation désirée de l’orifice de refoulement, à droite ou à - Brancher l’automatisme sur le réseau électrique, l’indicateur lumi-
gauche, monter le manomètre à l’aide des deux vis de fixation, en neux de tension va s’allumer (POWER).
ayant au préalable mis en place le joint torique sur l’axe (rep. 13). - Le temps d’amorçage d’une pompe auto-amorçante aspirant à 8
Obstruer l’orifice opposé à l’aide de la vis bouchon (sans joint torique mètre de profondeur peut atteindre 2 à 3 minutes. Durant cette
ni téflon). opération, maintenir la touche ”RESET” enfoncée.
- Vérifier que la tension d’alimentation soit 220 - 240 V (50 Hz ou 60 Hz). Attention, l’automatisme régule seulement la pression d’enclenche-
Pour accéder au bornier de raccordement, dévisser les quatre vis ment de la pompe. Il n’influence pas la pression dans l’installation qui
du couvercle de la boîte à bornes. dépend uniquement des caractéristiques de la pompe.
5
FRANCAIS
8.2 LE GROUPE POMPE a) Manque d’eau d’alimentation. Le sys- a) Vérifier l’alimentation et mettre en service la pompe avec le bouton de
NE DÉMARRE PAS. tème de sécurité s’est activé et l’indi- réarmement (RESET).
cateur lumineux (ALARM) est allumé :
b) Pompe bloquée. L’indicateur lumineux b) Contacter le Service Après-Vente.
(ALARM) est allumé. Le système de
sécurité à fonctionné. Quant on agit
sur le bouton de réarment, l’indicateur
lumineux (ON) s’allume mais la
pompe ne démarre pas :
c) Panne sur la carte électronique : c) Débrancher l’interrupteur d’alimentation électrique et raccorder de nou-
veau. La pompe doit démarrer, sinon procéder au remplacement de la
carte électronique.
d) Manque de tension : d) Vérifer que l’alimentation électrique est correcte, l’indicateur lumineux de
tension (POWER) doit être allumé.
e) La pression de la pompe est insuffisan- e) Vérifier que la pression maxi de la pompe est de 0,5 bar supérieure à la
te. Le système de sécurité a agi, l’indi- pression d’enclenchement de l’automatisme.
cateur lumineux correspondant
(ALARM) est allumé.
f) Entrée d’air dans l’aspiration de la f) Vérifier l’étanchéité des raccords et joints de la tuyauterie d’aspiration.
pompe. Le manomètre va indiquer
une pression inférieure à la normale
ou une oscillation constante. Le systè-
me de sécurité va agir en arrêtant le
fonctionnement de la pompe, l’indi-
cateur lumineux (ALARM) va s’allumer.
g) Les colonnes d’eau HR ou HC sont g) Augmenter le seuil d’enclenchement en tournant la vis (Voir FIG. 5- rep. 7).
supérieures à 15 m et le préréglage
en usine du seuil d’enclenchement
n’a pas été modifié.
8.2 LE GROUPE POMPE a) Petites fuites sur quelques points de a) Vérifier de possibles égouttements des robinets ou chasses d’eau et réparer
DÉMARRE ET S’AR- l’installation : ces fuites.
RÊTE À PLUSIEURS
REPRISES.
6
ENGLISH
7
ENGLISH
5.2 Mounting (See FIG. 2) - After a priming time varying between a few seconds and three
minutes, according to installation conditions, read off the pressure
Before connecting the hydraulic connector, it is
ATTENTION ! on the pressure gauge. This should be around the maximum value
essential to fill the pump completely.
for the pump. While it is running, the "ON" check light will remain lit.
Put the automatic control in a vertical position - Shut the tap; the pump will stop after about three to five seconds.
ATTENTION !
(vertical suction, horizontal discharge). Only the voltage indicator ”POWER” will stay lit.
- As soon as a tap is opened again, the pump will restart automati-
It can be connected either directly on to the pump discharge or
cally.
onto a rigid pipe between the pump and the first tap.
Any operational irregularities after these operations are due to faulty
5.3 Hydraulic connections priming of the pump. The safety system activation check light
The automatic control can be connected directly onto the pump ”ALARM” will come on. Fill the pump. Press the "RESET" button.
discharge (if DNR is 1") or onto a rigid pipe (supported) between the Adjusting the cut-in pressure.
pump and the first tap. If the head of water HR or HC (See FIG. 2) is higher than 15 m, the
We recommend that a flexible tube be fitted at the outlet of the pump cannot start up again at the cut-in pressure pre-set at the fac-
automatic control to avoid any stress on the body. tory. In this case, it is necessary to adjust this setting using the screw
The automatic control can be used with a pump connected to the (See FIG. 5 - 7). With the pump stopped and the tap open, read off
town water supply without a dry running protection device (with the pressure due to the head of water on the pressure gauge and
town pressure not exceeding 1 bar), as this is built in to the automa- turn the screw towards +, until the pump starts up.
tic control. For the same reason, a non-return or discharge valve bet- Fine-tune the setting during other start-stop cycles; read off the cut-
ween the pump and the automatic control is not necessary. in pressure on the pressure gauge and turn the screw in the desired
direction (+ or -).
5.4 Electrical connections
The maximum pump pressure should be 0.5 bar higher than the cut-
Electrical connections and checks must be carried out by a in pressure of the automatic control.
qualified electrician in accordance with local standards in Take care : The automatic control only regulates the pump cut-in
force. pressure. It does not affect the pressure in the installation, which
- Check that the supply voltage is 220-240 V (50 Hz or 60 Hz). To access depends only on the characteristics of the pump.
the connection terminal, unscrew the four screws in the terminal box Checking operation
cover. Open and then shut one or more taps in the network and make sure
- Connections are by three-strand cable WITH OBLIGATORY EART. that the pump-automatic control assembly is operating correctly.
- Connect the pump motor and the mains supply in accordance
If there is a power cut, the automatic control will
with the diagram printed on the plate inside. (See FIG 3). ATTENTION !
need to be reset manually, by pressing the "RESET"
DO NOT FORGET TO CONNECT THE EARTHINGS. button, when power returns (only in case of not automatic reset).
Three phase supply
The automatic control can be used with three phase pumps (or 7. MAINTENANCE - SERVICING
single phase pumps with current higher than 10 A) using a contactor. 7.1 Maintenance
In this case, connections will be made according to the diagram
The usual conditions apply for exchange of the machine if it proves
(See FIG. 4).
defective while under guarantee.
Check that the pump is full, to make sure of cor- 7.3 Disassembly- Reassembly
ATTENTION !
rect priming. Maintenance-free equipment.
6.2 Operation
- Open the installation tap slightly; the pump will start immediately.
8
ENGLISH
8. OPERATING TROUBLE
8.2 THE PUMP UNIT a) No water supply. The safety system a) Check the supply and start up the pump with the reset button ”RESET”.
DOES NOT START. has been activated and the ”ALARM”
check light is on :
b) Pump blocked. The ”ALARM” check b) Contact After-Sales Service.
light is on. The safety system has ope-
rated. When the reset button is pres-
sed, the ”ON” light comes on, but the
pump does not start up :
c) Faulty electronic card : c) Disconnect the electricity supply switch, then reconnect it. The pump
should start; otherwise replace the electronic card.
d) No power : d) Check that the electric power is correct. The voltage check light ”POWER”
should be on.
e) Pump pressure is insufficient. The safe- e) Check that the maximum pump pressure is 0.5 bar higher than the cut-in
ty system has operated and the cor- pressure of the automatic control.
responding check light ”ALARM” is on.
f) Air is entering the pump suction. The f) Check that the connections and suction piping seals are watertight.
pressure gauge indicates a lower than
normal pressure or constant oscilla-
tion. The safety system prevents pump
operation and the check light
”ALARM” comes on.
g) The HR or HC heads of water are g) Increase the cut-in threshold by turning the screw (See FIG. 5 -7).
higher than 15 m and the factory pre-
set cut-in threshold has not been
adjusted.
8.3 THE PUMP UNIT a) Small leaks at some points in the ins- a) Check for possible leaking taps or flushes and repair these leaks.
STARTS AND STOPS tallation :
REPEATEDLY.
9
NOTES
10
NOTES
11
FRANCAIS
CE MANUEL DOIT ETRE REMIS A
L'UTILISATEUR FINAL ET ETRE TOUJOURS
DISPONIBLE SUR SITE.
ENGLISH
THIS LEAFLET HAS TO BE GIVEN TO THE
END USER AND MUST BE LEFT ON SITE.
CB.N° 4.044.542/Ed.1
P.S. (SEA) Pte Lte SINGAPORE SALMSON VIETNAM W.S.L. LEBANON SALMSON ARGENTINA
1 Claymore Drive C3-319,Ly Thuong Kiet Bou Khater building, Mazda Center OTERO 172/4
10-03 Orchard Towers - 229594 Ph. 15 Q. 11 Hochiminhville Jal El Dib Highway - Ground Floor (1427) Buenos Aires
TEL. : (65) 834 0688 TEL. : (84-8) 864 52 80 PO Box 175 224 - BEIRUTH TEL.: (54) 11 48 56 59 55
FAX : (65) 834 0677 FAX : (84-8) 864 52 82 TEL. : (961) 04 722 280/281 FAX : (54) 11 48 56 49 44
[email protected] [email protected] FAX : (961) 04 722 285 [email protected]
[email protected]
POMPES SALMSON
53, BOULEVARD DE LA REPUBLIQUE - ESPACE LUMIÈRE - F-78403 CHATOU CEDEX
TEL. : +33 (0) 1 30 09 81 81 - FAX : +33 (0) 1 30 09 81 01
www.salmson.fr
POMPES SALMSON - SAS AU CAPITAL DE 16.775.000 € SIREN 313 986 838 RCS VERSAILLES - APE 291C