Beruflich Dokumente
Kultur Dokumente
Liag Katalog Deu-En 2021
Liag Katalog Deu-En 2021
Bogenventile
2
3
Saubere Sache
Klares System
Hygienic valves and pigging systems from LIAG® offer the maximum in
quality and product safety for the low-germ processing of high-grade
media.
4
1
www.liag-valve.com 5
Allgemeine Informationen
Werkstoffe
Werkstoff-Nr. nach Stahlsorte nach
AISI C% Si % Mn % Cr % Mo % Ni % Ti %
DIN 17007 DIN 17007
1.4301 304 X 5CrNi1810 ≤ 0,07 ≤ 1,00 ≤ 2,00 17,00-19,00 - 8,50-10,50 -
1.4306 304 L X 2CrNi1911 ≤ 0,03 ≤ 1,00 ≤ 2,00 18,00-20,00 - 10,00-12,50 -
1.4404 316 L X2CrNiMo1810 ≤ 0,03 ≤ 1,00 ≤ 2,00 16,50-18,50 2,00-2,50 11,40-14,00 -
1.4435 316 L X 2CrNiMo1812 ≤ 0,03 ≤ 1,00 ≤ 2,00 17,00-18,50 2,50-3,00 12,50-15,00 -
Dichtungen
Die produktberührenden Dichtungsqualitäten entsprechen den Bestimmungen des Lebensmittelgesetzes
(keine toxischen Basispolymere, Füllstoffe und Lösungsmittel), sowie den Vorschriften der DIN 11861.
Für das Ventilprogramm stehen standardmäßig Dichtungen aus EPDM und FPM (Viton®) zur Verfügung.
Gewindeanschlussarten
Ausführung / Oberflächen der Armaturen
DIN 11851 SMS 1145 Alle produktberührenden Teile werden aus porenfreien
Walz- oder Schmiedeteilen hergestellt und sind ohne
DN Gewinde DN Gewinde
Nachbehandlung schweißbar.
25 Rd 52 x 1/6" 25 (1") Rd 40 x 1/6" Produktberührte Innenflächen sind feingedreht / feingeschliffen.
40 Rd 65 x 1/6" 38 (1 ½") Rd 60 x 1/6" Außenflächen: feingedreht / gebürstet.
Bestellangaben
Zur einwandfreien Bearbeitung Ihres Auftrages, bitten wir bei Bestellung um folgende Angaben (Beispiel):
Ausführung
Menge Typ Benennung Werkstoff O-Ring Material Option / Typ
Pn.-Antrieb
3-Wege Bogenven-
Rückmeldeeinheit
til, AISI 316L Luft/Feder
7 50D530A21 EPDM Näherungsschalter 24V/DC
3 x Gewinde DIN (1.4404) (LÖ/FS)
Typ 25-102M55B
11851
Sonderanfertigungen / Speziallösungen
Außer den im Katalog aufgeführten Artikeln liefern wir eine Vielzahl von Spezialprodukten und Sonderapplikationen.
Beispiele hierfür sind: Kombination verschiedener Anschlussarten, Adaption von Antrieben unterschiedlicher Fabrikate,
Sonderkonstruktionen und Herstellung in enger Zusammenarbeit mit unseren Kunden.
6
General Information 1
Materials
Steel Grade
Material no. Abreviation
AISI C% Si % Mn % Cr % Mo % Ni % Ti %
acc. to DIN 17007 acc. to DIN
17007
1.4301 304 X 5CrNi1810 ≤ 0,07 ≤ 1,00 ≤ 2,00 17,00-19,00 - 8,50-10,50 -
1.4306 304 L X 2CrNi1911 ≤ 0,03 ≤ 1,00 ≤ 2,00 18,00-20,00 - 10,00-12,50 -
1.4404 316 L X2CrNiMo1810 ≤ 0,03 ≤ 1,00 ≤ 2,00 16,50-18,50 2,00-2,50 11,40-14,00 -
1.4435 316 L X 2CrNiMo1812 ≤ 0,03 ≤ 1,00 ≤ 2,00 17,00-18,50 2,50-3,00 12,50-15,00 -
Seals
All seals in contact with product meet the German legal requirements for the food industry, as well as the specifications
acc. to DIN 11861. These standard seal materials are: EPDM (ethylene-propylene-diene-rubber) and FPM (Viton®).
Thread Standards
Finish / Execution
DIN 11851 SMS 1145 All parts in contact with product are manufactured in
non-porous rolled or forged material being weldable
DN Thread DN Thread
without additional heat treatment.
25 Rd 52 x 1/6" 25 (1") Rd 40 x 1/6" Standard internal surface in contact with product:
40 Rd 65 x 1/6" 38 (1 ½") Rd 60 x 1/6" machined or fine ground.
Outside surface: machined / brushed.
50 Rd 78 x 1/6" 51 (2") Rd 70 x 1/6"
65 Rd 95 x 1/6" 63 (2 ½") Rd 85 x 1/6"
80 Rd 110 x ¼" 76 (3") Rd 98 x 1/6"
100 Rd 130 x ¼" 102 (4") Rd 132 x 1/6"
Order Specifications
Please state the following details when placing an order (example):
www.liag-valve.com 7
Chemische Beständigkeitsliste
Temperaturbereich -30°C bis -20°C bis -40°C bis -60°C bis -200°C bis
+100°C +200°C +160°C +200°C +260°C
kurzzeitig bis +130°C bis +230°C bis +180°C bis +230°C bis +300°C
A NBR FPM EPDM FEP PTFE E NBR FPM EPDM FEP PTFE
Aceton D D A A A Erdnussöl A A C A A
Acethylchlorid D A D A A Essigsäure heiss D D C A A
Acetylen, Ethen A A A A A Ethanol (Ethylalkohol) A C A A A
Acrylsäureethylester D D B A A
Ethylalkohol (Ethanol) A C A A A
Ameisensäuremethylester D D B A A
Ethylchlorid A A A A A
Ammoniak flüssig (wasserfrei) B D A A A
Ethylenchlorid D B D A A
Ammoniumcarbonat C B A A A
Ammoniumchlorid A A A A A F NBR FPM EPDM FEP PTFE
Apfelsäure A A B A A Gallussäure B A B A A
Gelatine A A A A A
B NBR FPM EPDM FEP PTFE
Glucose A A A A A
Baumwollsamenöl A A C A A
Glycerin A A A A A
Benzoesäure D A B A A
Glycerintriacetat B D A A A
Benzoesäuremethylester D A D A A
Glycol (Ethylenglykol) A A A A A
Bier A A A A A
Bleichlauge D A A A A K NBR FPM EPDM FEP PTFE
Bromwasserstoffsäure D A A A A Kaffee A A A A A
Buttersäure D B B A A Kaliumhydroxid-Lösungen B B A A A
(verdünnt)
Buttersäurebutylester D A A A A
Kohlensäure B A A A A
Butylalkohol A A B A A
Kokosfett A A C A A
C NBR FPM EPDM FEP PTFE
L NBR FPM EPDM FEP PTFE
Calciumchlorid A A A A A
Lacklösungsmittel D D D A A
Calciumhydroxid A A A A A
Lavendelöl B A D A A
Calciumsalze A A A A A
Lebertran A A A A A
Carbolsäure (Phenol) D A D A A
Leinöl A A C A A
Chloraceton D D A A A
Linolsäure B B D A A
Chloressigsäureethylester D A D A A
Chlorhaltiges salziges D A D A A M NBR FPM EPDM FEP PTFE
Meerwasser Maisöl A A C A A
Chlorkohlensäureethylester D A D A A Methan A A D A A
D NBR FPM EPDM FEP PTFE Methylalkohol (Methanol) A D A A A
Dampf unter +150°C D C A A A Milch A A A* A A
Dampf über +150°C D D B A A Milchsäure kalt A A A A A
Denaturierter Alkohol A A A A A Milchsäure heiss D A D A A
Diacetonalkohol (Diaceton) D D A A A
8
1
Natriumcarbonat (Soda) A A A A A
Natriumbicarbonat (Natron) A A A A A
Natriumchlorid (Kochsalz) A A A A A
Natriumhydroxid (Natronlau- B B A A A
ge) 3 molar
Natriumnitrat (Natronsalpeter) B A A A A
Natriumperoxid B A A A A
Natriumsalze A A A A A
Olivenöl A A B A A
Ozon D A A A A
Pflanzliche Öle A A C A A
Phenol D A D A A
Rizinusöl A A B A A
Rüböl A A A A A
Salicylsäure B A A A A
Salpetersäure 3-molar D A B A A
Den neben stehenden Angaben liegen Prüfungen bei
Salpetersäure konzentriert D A D A A unterschiedlichen Bedingungen zugrunde. Vielfach sind
Salzsäure 3-molar C A A A A die Werte jedoch bei Raumtemperatur und 7 Tagen (150
Std.) Einwirkungszeit ermittelt worden. In Einzelfällen
Salzsäure konzentriert D A C A A sind voneinander abweichende Feststellungen Labor/
Schmalz, tierisches Fett A A B A A Praxis durchaus möglich.
Aufgrund der unterschiedlichen Einsatzparameter und
Schwefelsäure 3-molar D A B A A Zusammensetzung der Medien sind diese Angaben nur
Richtwerte und unverbindlich.
Schwefelsäure konzentriert D A D A A
Schweflige Säure B A B A A
Sojaöl A A C A A
Vaseline A A D A A
Zitronensäure A A A A A
Zuckerlösungen A A A A A
Zuckerrohrlösung A A A A A
Zuckerrübensaft A A A A A
www.liag-valve.com 9
Chemical Resistance List
A NBR FPM EPDM FEP PTFE D NBR FPM EPDM FEP PTFE
Gallic acid B A B A A
B NBR FPM EPDM FEP PTFE
Gelatines A A A A A
Beer A A A A A
Glucose A A A A A
Benzoic acid D A B A A
Glycerine A A A A A
Benzoic methyl ester D A D A A
Glycerine triacetate B D A A A
Bleaching lye D A A A A
Glycol (ethylene glycol) A A A A A
Butanol (butyl alcohol) A A D A A
Groundnut oil A A C A A
Butter A A A A A
Butyl alcohol A A B A A
H NBR FPM EPDM FEP PTFE
Hydrobromic acid D A A A A
Butyric acid D B B A A
Hydrochloric acid 3-molar C A A A A
C
Butyricester acid NBR
D FPM
A EPDM
A FEP
A PTFE
A
Hydrochloric acid concen- D A C A A
Calcium chloride A A A A A trated
Calcium hydroxide A A A A A Hydrochlorouscarbonicethyl- D A D A A
Calcium nitrate (nitrate of A A A A A ester acid
lime) Hydrogen peroxide dilute B A A A A
Carbolic acid (phenol) D A D A A
L NBR FPM EPDM FEP PTFE
Carbonic acid B A A A A
Lactic acid cold A A A A A
Castor oil A A B A A
Lactic acid hot D A D A A
Chloracetone D D A A A
Lavender oil B A D A A
Chloroaceticethylester acid D A D A A
Linoleic acid B B D A A
Citric acid A A A A A
Linseed oil A A C A A
Coconut oil A A C A A
Cod liver oil A A A A A
M NBR FPM EPDM FEP PTFE
Maize oil A A C A A
Concentrated nitric acid A A A A A
Malic acid A A B A A
Cotton seed oil A A C A A
Methane A A D A A
Creosote, carbolineum A A D A A
Methyl alcohol (methanol) A D A A A
Milk A A A* A A
10
1
N NBR FPM EPDM FEP PTFE V NBR FPM EPDM FEP PTFE
Tartaric acid A A B A A
Trichloroacetic acid B C B A A
www.liag-valve.com 11
General Terms and Conditions per cent per year or
d) to rescind from the contract if the buyer fails to pay within a reasonable period
LIAG® – LÄUFER International AG of grace.
7.6 Until the buyer has fulfilled all financial obligations, the goods supplied shall
(Form 161) remain the supplier’s property. The buyer shall be obliged to meet all legal require-
ments in order to safeguard the supplier‘s property or security interest. In case of
1. Scope attachment or other kinds of seizure the buyer shall evidence the supplier‘s title
1.1 These General Terms and Conditions apply to all deliveries of goods or works. and notify the latter immediately.
In case of process- and pigging system-deliveries and of installations, specific LIAG
Conditions are supplemented (Form 162). 8. Warranty
1.2 Any alterations to the terms and conditions, mentioned under 1.1 are only 8.1 Unless otherwise agreed the warranty period shall be 24 months for com-pon-
binding if accepted in writing. ents from the date of transfer of risk as stated in 6.1, regardless of the legal
qualification of goods delivered or works performed.
2. Offer 8.2 Claims will be accepted only if the supplier is immediately notified of the defect
2.1 Offers by the supplier are made without obligation. in writing. They are restricted to the repair or replacement of the defective goods.
2.2 Specifications and quotes in catalogues, brochures etc., are only binding if All other costs are to be borne by the buyer.
expressly referred to in the order confirmation. 8.3 Defects which are due to abuse, misapplication, failure to follow the instructions
2.3 The offer or project documentation must neither be reproduced nor disclosed for use, warnings, safety or other regulations provided by the supplier, improper or
to third parties without the supplier‘s consent. The documentation remains the prolonged storage or other mistakes on the part of the buyer, are excluded
supplier‘s property and must be returned to him upon request. from the warranty. In case of products which have been produced at the order of
or according to the buyer‘s instructions or formulae, warranty will only cover the
3. Acceptance proper production of the goods.
3.1 The sales contract does not come into force until the buyer has received the Normal wear will not be covered under warranty.
written order confirmation from the supplier, or the goods have been effectively 8.4 Supplier‘s warranty obligations cease if any changes or repairs are caused by
delivered to the buyer. the buyer or a third person without supplier‘s prior written consent.
3.2 Subsequent changes or amendments to the contract may be stipulated only The performance of a warranty obligation does not prolong the original warranty
in writing. period.
4. Prices 9. Liability
4.1 Prices are quoted ex supplier‘s works or warehouse, excluding packaging, 9.1 The supplier‘s liability according to the Product Liability Act is excluded, if
dispatch and VAT. All expenses, duties and taxes related to the delivery are to the specific provisions regarding the handling of the products, instructions for their
buyer‘s account. use and/or warning and safety regulations as specified by the supplier have not
4.2 If an order should differ from the offer, the supplier reserves the right to change been observed.
prices accordingly. 9.2 Outside the scope of the Product Liability Act damages shall be compensated
4.3 Prices are based on the material and labour costs valid at the time of the first only if the supplier is held responsible for intent or gross negligence. In this case,
offer. Any changes to these costs prior to the date of delivery entitle the supplier to however, claims are limited to personal injury and material damage resulting directly
change prices accordingly. from a defect in the products. All other claims, such as consequential loss of
property or profit are explicitely excluded. Claims must be made in writing within a
5. Delivery and Dispatch period of six months from the date of occurrence of the damage, but not later than
5.1 Delivery periods do not run before the date of the order confirmation, and are two years from the date of delivery, otherwise they are forfeited.
deemed to be fulfilled when the goods are dispatched from the supplier‘s factory 9.3 Buyer is liable to subject his customers to the limitations of liability contained
or warehouse. in this paragraph.
5.2 If not explicitly agreed otherwise, any governmental or other permits required
for delivery in the buyer‘s country will delay, unless produced in time, delivery 10. Rescission of Contract
dates. They have to be obtained in the buyer‘s country by the buyer. 10.1 The buyer can rescind the contract if delivery is delayed more than 60 days
5.3 Terms and obligations of delivery are suspended as long as the buyer‘s payments because of gross negligence of the supplier and despite a reasonable period of
are in arrear. grace granted in writing.
5.4 The supplier is entitled to carry out and invoice partial or preliminary shipments. 10.2 Apart from the case of delayed payment according to para 7.5 d) the supplier
5.5 The agreed delivery periods are subject to force majeure, or unforeseen events can rescind the contract if
or events beyond the control of the supplier, such as war, Acts of God, governmental a) delivery or performance becomes impossible for reasons attributable to the
interventions and bans, energy and raw material shortages, strikes, transport buyer, or is delayed beyond a reasonable period of grace established in writing;
damages or delays. These events entitle the supplier to extend the time of delivery, b) the buyer‘s financial situation has worsened notably after ordering the products,
also if they affect any of his sub-suppliers. and he is not prepared to pay in advance, nor to provide sufficient security. Such
5.6 In case the delivery of the goods ready for dispatch is not possible or not rescission of contract shall also be permissible if only parts of the delivery or perfor-
desired by the buyer, the goods can be stored at the buyer‘s cost and risk. The mance, which are still to be fulfilled, are affected.
delivery shall then be considered as performed. 10.3 In case that, due to events indicated in para 5.5, the agreed delivery times are
5.7 Compensation for delays in delivery shall be payable only upon separate agree- delayed by more than one half of the period, but at least six months, either party
ment, and shall be limited to an eventual penalty stipulated by the parties, even if shall be entitled to rescind the contract with respect to those parts of the delivery
delays are caused by the supplier‘s negligence. or performance which have still to be fulfilled.
10.4 If bankruptcy proceedings are instituted against either party‘s assets, or these
6. Performance of Contract and Transfer of Risk proceedings are not instituted because of insufficient assets, the other party may
6.1 Costs and all risks are transferred to the buyer at the time of dispatch of the rescind the contract with immediate effect.
goods from the supplier‘s factory or warehouse, in default of the agreed delivery 10.5 In case of rescission of contract for other reasons than the one stated in 10.1
terms. This also applies in case of installations at the buyer‘s premises and transport all performances or parts thereof which have already been fulfilled by supplier,
by the supplier. shall be settled and paid according to the contractual provisions, notwithstanding
6.2 If delivery is delayed by the buyer, transfer of costs and risk shall become effective supplier’s claims for damages. This also applies to deliveries and performances
when the goods are ready for dispatch. not yet accepted by the buyer as well as to any preparatory work undertaken by
6.3 All periods depending on the supplier‘s performance of contract run from the the supplier.Alternatively, supplier is entitled to claim the restitution of products
dates specified in this section, irrespective of any quality tests or trial runs. already delivered.
Any other consequences resulting from a rescission of contract are excluded.
7. Payment
7.1 Unless otherwise agreed in writing, components shall be paid within 30 days 11. Patent Rights, Copyright
from the invoice date after delivery. Systems, 40% of the contract price shall be 11.1 In the event a product is produced according to the buyer‘s construction,
paid after receipt of the order confirmation, 50% at the time of delivery and the drawings or specifications, the buyer has to keep the supplier harmless and indemni-
remaining 10% within 30 days after delivery. Unless otherwise agreed, all invoices fied for any infringement of patent rights of third parties.
of the supplier shall become due within 30 days from the date of invoice. 11.2 All technical documents, in particular plans, drawings, technical descriptions,
7.2 Partial invoices are due immediately upon receipt. This also applies to payments as well as catalogues, brochures, pictures or models etc. are the supplier‘s exclusive
which have to be made for additional performances, beyond the initial terms of property and are subject to legal and statutory restrictions on copy, reproduction,
contract, regardless of the conditions of payment applicable to the main perfor- competitive use etc.
mance. Para 2.3 also applies to such documents.
7.3 Payment shall be made without any deduction in the agreed currency to the
supplier‘s bank. Cheques or bills of exchange shall be accepted on account only, 12. Place of Jurisdiction, Applicable Law
and all connected expenses shall be charged to the buyer‘s account. 12.1 In case of controversies arising from the contract the venue of legal proceedings
shall be the German tribunal at the supplier‘s registered place of business.
7.4 The buyer shall not be entitled to withhold or reduce any payments due because The supplier shall, however, also be entitled to take action before a competent
of warranty or compensation claims. tribunal at the buyer’s place of business.
7.5 In case of delayed payment the supplier is entitled either 12.2 The parties may also agree to have controversies settled by arbitration.
a)to postpone his own obligations until receipt of the payments due, 12.3 The contract shall be construed and interpreted according to German
b) to fix a due date for all outstanding payments (cancellation of periods of law. It is mutually agreed that the UNCITRAL Agreement of the United Nations on
payment), the law of international sales of goods does not apply.
c) to charge from maturity, interest at the current discount rate of Germany plus 5
07/2020 Form 161
12
Amendment to the General Terms and
Conditions Form 161 for Process- and
Pigging Systems 1
LIAG® – LÄUFER International AG
(Supplement Form 162)
1. Scope
These Amendment Form 162 are special conditions that shall be applied to the delivery of process systems.
Unless stipulated otherwise in these Conditions, the General Terms and Conditions of LIAG Form 161 shall
apply.
2.1 For process- and pigging systems not excluded from warranty, LIAG guarantees correspondence with
the contractual specifications, provided that the system is installed properly and used under the conditions
specified in the contract.
2.2 The warranty includes error diagnosis and error correction during the duration of the warranty period.
Unless stipulated otherwise, the warranty period for system is three months from the date of acceptance.
The correction of errors, i.e. deviations from the valid specifications which impair the functioning of the system,
is effected by LIAG through support and instructions for troubleshooting,. If this is not possible, error correction
implies delivery of additional system components or, redesigned system equipment. If this is not possible,
troubleshooting (modification of system) at the buyer‘s place. The preconditions for the correction of a system
error are that the error impairs the functioning of the process; that the error is reproducable; that the buyer has
installed the system, if any, offered to him free of charge during the warranty period; that the buyer provides all
information and material necessary for error correction; and that LIAG has access to the hardware and software
belonging to the system during normal working hours. The buyer agrees to support LIAG in error correction
by providing a qualified expert whose qualifications meet the requirements of the system and who helps to
remove the error.
2.3 LIAG does not warrant systems which has been modified by the buyer or by third parties without LIAG’s
consent and knowledge, even if the error occurs in a part not modified. If during error analysis the conclusion is
made that the error is not subject to warranty or that the error was not caused by the delivered system,
the buyer is charged with all resulting costs.
2.4 LIAG does not guarantee that the system functionality meets all requirements of the buyer, that the system
run with other processing components used by the buyer; that the system runs without interruptions or errors;
or that all system errors can be corrected.
2.5 Should, during warranty period, the system be deficient in the way that it does not meet the specifications
and should LIAG, in spite of sustained efforts, not be able to remove the error and should the buyer for this
reason not be able to use the system, each party has the right to rescind the Contract with immediate effect
and refund the received performances.
2.6 The presence of deficiencies in individual system parts does not entitle the buyer to rescind the contract
also with respect to the complete process- and/or pigging system.
2.7 The warranty excludes any other claim and the liability for any damage arising out of the use of the system.
www.liag-valve.com 13
Rücknahmebedingungen
LIAG -LÄUFER International AG
1. Diese Richtlinien regeln Rückgaben die nicht durch die Produktgewährleistung gedeckt sind und betreffen:
a. Fehlbestellung von Ventilen / Produkten / Ersatzteilen
b. Stornierte Bestellungen durch den Kunden, etc.
2. In Betrieb genommene (benutzte) Standardteile / Produkte, unabhängig von der Dauer der Benutzung und ihres Zustands, fallen nicht unter diese Richtlinien
und können deshalb nicht zurückgenommen werden.
3. Unbenutzte Standardteile / Produkte ohne autorisierte Rückgabenummer können nicht akzeptiert werden und sind von diesen Richtlinien ausgeschlossen.
4. Unbenutzte Standardteile / Produkte, die nicht innerhalb von 14 Tagen nach Lieferdatum zur Rückgabe reklamiert werden, sind von diesen Richtlinien
ausgeschlossen.
5. Vor der Rücksendung jedweder unbenutzten Standardteile / Produkten muss durch den Erwerber bei der LIAG-LÄUFER International AG innerhalb von
14 Tagen nach Lieferdatum eine Rückgabenummer angefordert werden. Die Rückgabenummer ist notwendig, um den Rückgabeprozess abzuwickeln.
6. Wiedereinlagerungsgebühren für unbenutzte und innerhalb von 14 Tagen nach Lieferdatum zur Rückgabe reklamierten Standardteile / Produkte mit
Rückgabenummer:
a. Unbenutzte Standardteile / Produkte, mit einer Ersatzbestellung (mit gleichem oder höheren Warenwert als die reklamierten Produkte):
Gutschrift von 80% des ursprünglichen Auftragswerts. (ausgenommen Verpackungs- und Frachtkosten)
b. Unbenutzte Standardteile / Produkte, ohne eine Ersatzbestellung (mit gleichem oder höheren Warenwert als die reklamierten Produkte):
Gutschrift von 65% des ursprünglichen Auftragswerts. (ausgenommen Verpackungs- und Frachtkosten)
7. Kundenspezifisch angefertigte Sonderventile und Molchsende-, Molchempfangs- und Produktausschiebestationen können nach Fertigungsbeginn (es gilt
die Zusendung und das Erstelldatum der Auftragsbestäigung) nicht zurückgenommen werden, wenn durch die LIAG-LÄUFER International AG kein
anderer Verwendungszweck gefunden werden kann. Gutschriften werden je nach Fall festgelegt.
8. Gutschriften werden nach Rücksendung und Inspektion der reklamierten Produkte DAP/DDP, LIAG-LÄUFER International AG, Am Wasserstall 12,
88682 Salem / Deutschland ausgestellt.
Der Erwerber ist verantwortlich für die Verpackung und Rücksendung der Produkte in einwandfreiem, neuwertigen Zustand.
Notwendige Zusatzarbeiten von durch die Rücklieferung verursachten Beschädigungen werden von der Gutschrift einbehalten.
07/2020
Return Policy
LIAG – LÄUFER International AG
This policy is intended for returns that are not covered by product warranty, i.e. wrong valve type or part was ordered, customer canceled order, etc.
Before returning any product, contact us for a Returned Material Authorization Number (RMA#) within 14-days after delivery. This will eliminate confusion when the
parts are received and facilitate processing the return.
No action will be taken on returned parts without an RMA, already used parts or later than 14-days after delivery.
Standard valve(s) and standard parts with a replacement order 20%. Standard valve(s) and standard parts without a replacement order 35%.
Additional restocking charges up to 100% may be assessed for the following circumstance:
Special customized valves and pigging launching-/receiving or pigging product pushing out stations are not returnable anymore for any work in progress items
(usually from the date of order confirmation) unless we have a use for them. Credit will be determined on a case-by-case basis.
Credit will be issued only after parts are returned DAP/DDP 88682 Salem / Germany, and inspected. Customer is responsible for packaging parts so they are
returned in “as new” condition. Any labor required by LÄUFER to return the parts to “as new” condition will be deducted from the credit.
Issue: 07/2020
14
BOGENVENTILE
ARC VALVES
2
Ideal für zähe, pastöse Medien
und keimarme Molchprozesse
www.liag-valve.com 15
Bauteile und Funktionsweise
Principle of Design
Betriebsdruck
Operating pressure
max. 10 bar (145 psi) Betriebsdruck
(DyneonTM TFM1600) Operating pressure
max. 15 bar (217,5 psi) max. 3 bar (43,5 psi)
(PTFE + 15% Peek)
max. 20 bar (290 psi)
(Tecapeek)
Ventilgehäuse
Valve body
Federbogen mit Vorspannung
mittels Linienberührung wird das Schließ-
segment gegen das Gehäuse gepresst
Anzugsmutter / Konus Prestressed arc (line contact)
Gegenlager bei Druckschlägen sowie the arc presses the shutter against
zur Erhöhung des Anpressdrucks the valve body
Pinching nut / cone
to increase the sealing pressure
Schaltstellungen
Operating positions
2-Wege Bogenventil
2-way arc valve
3-Wege Bogenventil
3-way arc valve
16
Technische Daten
Technical Data Overview
2
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI 316L (1.4404 / 1.4435) with product: AISI 316L (1.4404 / 1.4435)
Andere Edelstahlteile: AISI 304 (1.4301) Other inox parts: AISI 304 (1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Schließer: DyneonTM TFM1600 Shutter: DyneonTM TFM1600
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32 µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32 µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
– Optional bis 200°C (392°F) – optionally up to 200°C (392°F)
Ausführungen Versions
2- / 3- / 4-Wege (a. A.) 2- / 3- / 4-way (upon request)
www.liag-valve.com 17
BOGENVENTILE DIN
ARC VALVES
18
BOGENVENTILE DIN
ARC VALVES
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Schweißende DIN 11850
2-way arc valve series 21, pneumatic (air/air - air/spring), welded ends DIN 11850
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25D52A21 26 29 300 50 128 89
40 40D52A21 38 41 335 65 160 89
2
50 50D52A21 50 53 340 70 164 104
65 65D52A21 66 70 422 80 220 129
80 80D52A21 81 85 440 90 230 129
100 100D52A21 100 104 474 110 260 129
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde DIN 11851
2-way arc valve series 21, pneumatic (air/air - air/spring), male ends DIN 11851
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25D520A21 26 52 300 50 136 89
40 40D520A21 38 65 335 65 164 89
50 50D520A21 50 78 340 70 187 104
65 65D520A21 66 95 422 80 233 129
80 80D520A21 81 110 440 90 263 129
100 100D520A21 100 130 474 110 311 129
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Schweißende DIN 11850
2-way arc valve series 21, pneumatic (air/air - air/spring), welded ends DIN 11850
DN Typ Type Ø d1 Ø d2 H h L L1
25 25D52Ab21 26 29 287 50 128 161
40 40D52Ab21 38 41 320 65 160 161
50 50D52Ab21 50 53 328 70 164 161
65 65D52Ab21 66 70 370 80 220 209
80 80D52Ab21 81 85 386 90 230 209
100 100D52Ab21 100 104 423 110 260 209
150 150D52Ab 150 154 540 140 500 333
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde DIN 11851
2-way arc valve series 21, pneumatic (air/air - air/spring), male ends DIN 11851
DN Typ Type Ø d1 Ø d2 H h L L1
25 25D520Ab21 26 52 287 50 136 161
40 40D520Ab21 38 65 320 65 164 161
50 50D520Ab21 50 78 328 70 187 161
65 65D520Ab21 66 95 370 80 233 209
80 80D520Ab21 81 110 386 90 263 209
100 100D520Ab21 100 130 423 110 311 209
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
www.liag-valve.com 19
BOGENVENTILE DIN
ARC VALVES
20
BOGENVENTILE DIN
ARC VALVES
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Schweißende DIN 11850
3-way arc valve series 21, pneumatic (air/air - air/spring), welded ends DIN 11850
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25D53A21 26 29 300 50 128 89
40 40D53A21 38 41 335 65 160 89
2
50 50D53A21 50 53 340 70 164 104
65 65D53A21 66 70 422 80 220 129
80 80D53A21 81 85 440 90 230 129
100 100D53A21 100 104 474 110 260 129
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde DIN 11851
3-way arc valve series 21, pneumatic (air/air - air/spring), male ends DIN 11851
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25D530A21 26 52 300 50 136 89
40 40D530A21 38 65 335 65 164 89
50 50D530A21 50 78 340 70 187 104
65 65D530A21 66 95 422 80 233 129
80 80D530A21 81 110 440 90 263 129
100 100D530A21 100 130 474 110 311 129
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Schweißende DIN 11850
3-way arc valve series 21, pneumatic (air/air - air/spring), welded ends DIN 11850
DN Typ Type Ø d1 Ø d2 H h L L1
25 25D53Ab21 26 29 287 50 128 161
40 40D53Ab21 38 41 320 65 160 161
50 50D53Ab21 50 53 328 70 164 161
65 65D53Ab21 66 70 370 80 220 209
80 80D53Ab21 81 85 386 90 230 209
100 100D53Ab21 100 104 423 110 260 209
150 150D53Ab 150 154 540 140 500 333
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde DIN 11851
3-way arc valve series 21, pneumatic (air/air - air/spring), male ends DIN 11851
DN Typ Type Ø d1 Ø d2 H h L L1
25 25D530Ab21 26 52 287 50 136 161
40 40D530Ab21 38 65 320 65 164 161
50 50D530Ab21 50 78 328 70 187 161
65 65D530Ab21 66 95 370 80 233 209
80 80D530Ab21 81 110 386 90 263 209
100 100D530Ab21 100 130 423 110 311 209
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
www.liag-valve.com 21
BOGENVENTILE SMS
ARC VALVES
22
BOGENVENTILE SMS
ARC VALVES
2
51 51S52A21 48,5 51 340 70 164 104
63 63S52A21 60,5 63,5 355 75 210 104
76 76S52A21 72 76 422 80 220 129
102 102S52A21 97,6 101,6 474 110 310 129
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde SMS 1145
2-way arc valve series 21, pneumatic (air/air - air/spring), male ends SMS 1145
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25S520A21 22,5 40 300 50 110 89
38 38S520A21 35,5 60 335 65 140 89
51 51S520A21 48,5 70 340 70 164 104
63 63S520A21 60,5 85 355 75 210 104
76 76S520A21 72 98 422 80 220 129
102 102S520A21 97,6 132 474 110 310 129
SMS102 nur in Luft/Luft SMS102only in air/air
2-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde SMS 1145
2-way arc valve series 21, pneumatic (air/air - air/spring), male ends SMS 1145
DN Typ Type Ø d1 Ø d2 H h L L1
25 25S520Ab21 22,5 40 287 50 110 161
38 38S520Ab21 35,5 60 320 65 140 161
51 51S520Ab21 48,5 70 328 70 164 161
63 63S520Ab21 60,5 85 342 75 210 161
76 76S520Ab21 72 98 370 80 220 209
102 102S520Ab21 97,6 132 423 110 310 209
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
www.liag-valve.com 23
BOGENVENTILE SMS
ARC VALVES
24
BOGENVENTILE SMS
ARC VALVES
2
51 51S53A21 48,5 51 340 70 164 104
63 63S53A21 60,5 63,5 355 75 210 104
76 76S53A21 72 76 422 80 220 129
102 102S53A21 97,6 101,6 474 110 310 129
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde SMS 1145
3-way arc valve series 21, pneumatic (air/air - air/spring), male ends SMS 1145
DN Typ Type Ø d1 Ø d2 H h L Ø D1
25 25S530A21 22,5 40 300 50 110 89
38 38S530A21 35,5 60 335 65 140 89
51 51S530A21 48,5 70 340 70 164 104
63 63S530A21 60,5 85 355 75 210 104
76 76S530A21 72 98 422 80 220 129
102 102S530A21 97,6 132 474 110 310 129
3-Wege Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde SMS 1145
3-way arc valve series 21, pneumatic (air/air - air/spring), male ends SMS 1145
DN Typ Type Ø d1 Ø d2 H h L L1
25 25S530Ab21 22,5 40 287 50 110 161
38 38S530Ab21 35,5 60 320 65 140 161
51 51S530Ab21 48,5 70 328 70 164 161
63 63S530Ab21 60,5 85 342 75 210 161
76 76S530Ab21 72 98 370 80 220 209
102 102S530Ab21 97,6 132 423 110 310 209
Pneumatikantrieb mit Aluminiumgehäuse – Serie B, Gehäuse mit PTFE Beschichtung auf Anfrage
Pneumatic actuator with aluminium housing – series B, PTFE coated housing upon request
www.liag-valve.com 25
BOGENVENTILE Zoll / Inch
ARC VALVES
26
BOGENVENTILE Zoll / Inch
ARC VALVES
2
2" 51C52A21 47,5 50,8 340 70 164 104
2½" 63C52A21 60,2 63,5 355 75 210 104
3" 76C52A21 72,9 76,2 422 80 220 129
4" 102C52A21 97,4 101,6 474 110 310 129
www.liag-valve.com 27
BOGENVENTILE Zoll / Inch
ARC VALVES
28
BOGENVENTILE Zoll / Inch
ARC VALVES
2
2" 51C53A21 47,5 50,8 340 70 164 104
2½" 63C53A21 60,2 63,5 355 75 210 104
3" 76C53A21 72,9 76,2 422 80 220 129
4" 102C53A21 97,4 101,6 474 110 310 129
www.liag-valve.com 29
30
MOLCHWEICHEN
PIGGING VALVES
www.liag-valve.com 31
Bauteile und Funktionsweise
Principle of Design
Kein Totraum
vollständiges Ventildeckel
Ausspülen im CIP Valve cap
No dead pockets
full cleaning in CIP
Ventilgehäuse
Valve body
Schaltstellungen
Operating positions
Molchweiche 90°/120°
Pigging valve 90°/120°
32
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI 316L (1.4404 / 1.4435) with product: AISI 316L (1.4404 / 1.4435)
Andere Edelstahlteile: AISI 304 (1.4301) Other inox parts: AISI 304 (1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Schließer: DyneonTM TFM1600 Shutter: DyneonTM TFM1600
Oberflächen
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32 µin)
Surfaces
In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32 µin)
3
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
– Optional bis 200°C (392°F) – optionally up to 200°C (392°F)
Ausführungen Versions
3-Wege (3 x 120°) 3-way (3 x 120°)
www.liag-valve.com 33
Molchweichen DIN
Pigging Valves
34
Molchweichen SMS
Pigging Valves
www.liag-valve.om 35
Molchweichen Zoll / Inch
Pigging Valves
36
3
www.liag-valve.om 37
SONDERVENTILE
CUSTOMIZED VALVES
38 39
SONDERVENTILE
CUSTOMIZED VALVES
www.liag-valve.com 39
40
4.1 2-Wege Regel-Bogenventil
2-way Control Arc Valve
www.liag-valve.com 41
2-Wege Regel-Bogenventil
2-Way Control Arc Valve
2-Wege Regel-Bogenventil
2-way control arc valve
DN 25 60 m3/h
DN 40 140 m3/h
DN 50 340 m3/h
DN 65 450 m3/h
DN 80 620 m3/h
DN 100 990 m3/h
Kv-Wert [%]
Kv-value [%]
Auslass:
Auslass: mit Linerarisierungseinsatz "Quadrat"
Linerarisierungseinsatz „Quadrat“
outlet: Linearization insert “square”
Outlet: Linearization insert “square”
Auslass: mit Linerarisierungseinsatz „Rechteck“
Auslass: mit Linerarisierungseinsatz
outlet: Linearization "Rechteck"
insert “rectangle”
Outlet: Linearization insert “rectangle”
Öffnungswinkel Absperrorgan
Shutter
Apertureaperture
angle angle
42
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI 316L (1.4404 /1.4435) with product: AISI 316L (1.4404 /1.4435)
Andere Edelstahlteile: AISI 304 (1.4301) Other inox parts: AISI 304 (1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Schließer: DyneonTM TFM1600 Shutter: DyneonTM TFM1600
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
– Optional bis 200°C (392°F) – optionally up to 200°C (392°F)
4
Betriebsdruck Operating pressure
Druck hinter Pressure behind arc: 10 bar (145 psi)
Federbogen: 10 bar (145 psi) – optionally up to 20 bar
– Optional bis 20 bar (290,1 psi) (290,1 psi)
Druck gegen Pressure against arc: 3 bar (43,5 psi)
Federbogen: 3 bar (43,5 psi)
Ausführungen Versions
2-Wege 2-way
Antrieb Actuator
Elektropneumatische Regeleinheit bestehend aus: Electro-pneumatic control unit consisting of:
• pneumatischem Stellantrieb 0°-90° • pneumatic actuator 0°-90°
• Stellungsregler Positurn 4-20mA (0-10V), 24V DC, IP65 • positioner Positurn 4-20mA (0-10V), 24V DC, IP65
www.liag-valve.com 43
Regelventil DIN
Control Valve
2-Wege Regel-Bogenventil Serie 21, pneumatisch (L/L - L/F) Schweißende DIN 11850
2-way control arc valve series 21, pneumatic (air/air - air/spring), welded ends DIN 11850
DN Typ Type Ø d1 Ø d2 H h L L1 L2
25 25D52Aep21 26 29 331 50 128 198 154
40 40D52Aep21 38 41 364 65 160 198 154
50 50D52Aep21 50 53 370 70 164 198 154
65 65D52Aep21 66 70 413 80 220 198 154
80 80D52Aep21 81 85 429 90 230 198 154
100 100D52Aep21 100 104 465 110 260 198 154
Elektropneumatische Regeleinheit bestehend aus:
• pneumatischem Stellantrieb 0°-90°
• Stellungsregler Positurn 4-20mA (0-10V), 24V DC, IP65
Electro-pneumatic control unit consisting of:
• pneumatic actuator 0°-90°
• positioner Positurn 4-20mA (0-10V), 24V DC, IP65
2-Wege Regel-Bogenventil Serie 21, pneumatisch (L/L - L/F), Gewinde DIN 11851
2-way control arc valve series 21, (air/air - air/spring), male ends DIN 11851
DN Typ Type Ø d1 Ø d2 H h L L1 L2
25 25D520Aep21 26 52 331 50 136 198 154
40 40D520Aep21 38 65 364 65 164 198 154
50 50D520Aep21 50 78 370 70 187 198 154
65 65D520Aep21 66 95 413 80 233 198 154
80 80D520Aep21 81 110 429 90 263 198 154
100 100D520Aep21 100 130 465 110 311 198 154
Elektropneumatische Regeleinheit bestehend aus:
• pneumatischem Stellantrieb 0°-90°
• Stellungsregler Positurn 4-20mA (0-10V), 24V DC, IP65
Electro-pneumatic control unit consisting of:
• pneumatic actuator 0°-90°
• positioner Positurn 4-20mA (0-10V), 24V DC, IP65
SMS
Zoll / Inch
2-Wege Regel-Bogenventil Serie 21, pneumatisch (L/L - L/F), Schweißende
2-way control arc valve series 21, pneumatic (air/air - air/spring), welded ends
DN Typ Type Ø d1 Ø d2 H h L L1 L2
1" 25C52Aep21 22,2 25,4 331 50 110 198 154
4
1½" 38C52Aep21 34,9 38,1 364 65 140 198 154
2" 51C52Aep21 47,5 50,8 370 70 164 198 154
2½" 63C52Aep21 60,2 63,5 413 75 210 198 154
3" 76C52Aep21 72,9 76,2 429 80 220 198 154
4" 102C52Aep21 97,4 101,6 465 110 310 198 154
Elektropneumatische Regeleinheit bestehend aus:
• pneumatischem Stellantrieb 0°-90°
• Stellungsregler Positurn 4-20mA (0-10V), 24V DC, IP65
Electro-pneumatic control unit consisting of:
• pneumatic actuator 0°-90°
• positioner Positurn 4-20mA (0-10V), 24V DC, IP65
46
Venturi Ventil DIN
Venturi Valve
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI316L (1.4404) with product: AISI316L (1.4404)
Andere Edelstahlteile: AISI304 (1.4301) Other inox parts: AISI304(1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Schließer: DyneonTM TFM1600 Shutter: DyneonTM TFM1600
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
- Optional bis 200°C (392°F) - optional up to 200°C (392°F)
4
Betriebsdruck Operating pressure
Druck hinter Pressure
Federbogen: 10 bar (145 psi) behind arc: 10 bar (145 psi) – optionally
– Optional bis 20 bar (290,1 psi) up to 20 bar (290,1 psi)
Druck gegen Pressure
Federbogen: 3 bar (43,5 psi) against arc: 3 bar (43,5 psi)
www.liag-valve.com 49
4.3 EASY-OPEN Bogenventil für die Fleischindustrie
EASY-OPEN Arc Valve for the meat industry
50
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI316L (1.4404) with product: AISI316L (1.4404)
Andere Edelstahlteile: AISI304 (1.4301) Other inox parts: AISI304(1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Schließer: Dyneon TM TFM1600 Shutter: Dyneon TM TFM1600
Für Fleischbrät mit eventuellen Rückständen von For meat paste with eventual residues of abrasive
abrasiven Knochensplittern wird der Einsatz des particle of e.g. bones we recommend to use the
glasfaserverstärkten Teflon (GL25) Schließers empfohlen. glassfibre-reinforced Teflon (GL25).
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
4
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
- Optional bis 200°C (392°F) - optional up to 200°C (392°F)
www.liag-valve.com 51
4.4 Leckageüberwachung der beweglichen O-Ring Dichtung bei Bogenventilen
Leakage control of the moving O-ring seal of Arc Valves
Zur maximalen Erhöhung der Produkti- For maximum product safety, arc valves Merkmale
onssicherheit von LIAG® Bogenventilen are available with a leakage monitoring • Maximale Produktionssicherheit
kann die einzige im Ventil vorhandene system of the only moving/dynamic • Keine Keimeinschleppung durch Defekt der
bewegliche/dynamische O-Ring o-ring. The specific design identifies beweglichen O-Ring Dichtung
Dichtung auf eine mögliche Leckage, possible wearing defects of the seal and • Schnelle Schaltzeit durch geringes
bzw. Defekt durch Verschleiß überwacht prevents any contamination from the Betätigungsmoment (Kugellagerführung)
und mögliche Keimeinschleppungen outside environment. • Nachrüstbar für Bogenventile
von außen verhindert werden. The special designed leakage chamber
Die Überwachung und Sicherung des can act as a steam barrier or offer
konstruktiv zusätzlichen Leckageraums monitoring via means of a level
oberhalb der beweglichen O-Ring conductor control (dilution of glycerine). Features
Dichtung erfolgt entweder mittels The pivoting axle is supported with a Maximum product safety for
•
Dampfsperre oder durch elektronische stainless steel ball-bearing shaft for low-germ processes
Überwachung des Leitwerts einer sog. increased radial stability and 80% less • No contamination from the outside
Leckageraumfüllung mit 98%iger required operating torque compared environment by as a result of excessive
Glyzerinlösung. Zur Erhöhung der with the standard arc valve. wearing or a defective stem o-ring seal
Radialstabilität wird die Ventilachse bei • Quick acting valve due to low operating
beiden Verfahren in einem Edelstahlku- torque requirements (ball bearing supported
gellager geführt. Gleichzeitig reduziert main shaft)
sich das Schaltmoment der Ventilachse • Able to be retrofit to arc valves
um mehr als 80%.
52
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI316L (1.4404) with product: AISI316L (1.4404)
Andere Edelstahlteile: AISI304 (1.4301) Other inox parts: AISI304(1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, O-ring seals: EPDM, FPM (Viton®), FEP,
andere Qualitäten auf Anfrage other grades upon request
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
- Optional bis 200°C (392°F) - Optional bis 200°C (392°F)
Leckagekopf
Leakage cap
www.liag-valve.com 53
BAU- UND ERSATZTEILE FÜR LECKAGEKOPF
UNIT AND SPARE PARTS FOR LEAKAGE CAP
54
ERSATZTEILE & ZUBEHÖR
SPARE PARTS & ACCESSORiES
www.liag-valve.com 56
ERSATZTEILE UND ZUBEHÖR
SPARE PARTS AND ACCESSORiES
LIAG® Bogenventile
LIAG® arc valves
Lagerbuchse
Bearing bush
Schließer
Shutter
LIAG® Molchweichen
LIAG® pigging valves
Lagerbuchse
Bearing bush
Schließer
Shutter
57
ERSATZTEILE Für Bogenventile und Molchweichen
UND ZUBEHÖR For arc valves and pigging valves
SPARE PARTS
AND ACCESSORiES
5
150 6" 150D502V
www.liag-valve.com 58
ERSATZTEILE Für Bogenventile und Molchweichen
uND ZUBEHÖR For arc valves and pigging valves
SPARE PARTS
AND ACCESSORiES
DyneonTM TFM1600 Schließer DyneonTM TFM1600 shutter
DN Typ Type
25 25 1" 25SD501T
40 38 1½" 38-40SD501T
50 51 2" 50-51SD501T
63 2½" 63S501T
65 76 3" 65-76SD501T
80 80D501T
100 102 4" 100-102SD501T
150 6" 150D501T
25 25 1" 25SD501P
40 38 1½" 38-40SD501P
50 51 2" 50-51SD501P
63 2½" 63S501P
65 76 3" 65-76SD501P
80 80D501P
100 102 4" 100-102SD501P
40 38 1½" 38-40SD501TP
50 51 2" 50-51SD501TP
63 2½" 63S501TP
65 76 3" 65-76SD501TP
80 80D501TP
100 102 4" 100-102SD501TP
59
ERSATZTEILE Für Bogenventile und Molchweichen
UND ZUBEHÖR For arc valves and pigging valves
SPARE PARTS
AND ACCESSORIES
Lagerbuchse aus POM (Polyacetal) Bearing bush POM (Polyacetal)
DN Typ Type
25 25 1" 25SD503
40 38 1½" 38-80SD503
50 51 2" 38-80SD503
65 63 2½" 38-80SD503
80 76 3" 38-80SD503
100 102 4" 100-102SD503
150 6" 150SD503
www.liag-valve.com 60
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORiES
Standard Handhebel, 4 x 90°
Standard handle, 4 x 90°
DN L1 h Typ Type
25 25 1" 160 51 25-40SD506-90
40 38 1½" 160 51 25-40SD506-90
50 51 2" 190 51 50-63SD506-90
63 2½" 190 51 50-63SD506-90
65 76 3" 190 51 65-80SD506-90
80 190 51 65-80SD506-90
100 102 4" 270 51 100-102SD506-90
150 6" 270 55 150D506-90
61
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORiES
Edelstahlantrieb-Serie KH Luft/Feder 0° - 90° mit Steuerkopf TOP
Stainless steel actuator series KH, air/spring 0° - 90° with control unit TOP
DN Typ Type Ø D1 Ø D2 H h
25 25 1" 25-40KH002 L/F TOP 102 89 316 111
40 38 1½" 25-40KH002 L/F TOP 102 89 316 111
50 51 2" 50-63KH004 L/F TOP 102 104 316 111
63 2½" 50-63KH004 L/F TOP 102 104 316 111
65-80 76 3" 65-80KH006 L/F TOP 102 129 371 111
100 102 4" 100-102LKLA-T* 102 133 385 127
* Edelstahlantrieb Serie Alfa / Stainless steel actuator series Alfa
ASi oder DeviceNet auf Anfrage 50 51 2" 50-63KH004 L/L TOP 102 104 316 111
ASi or DeviceNet upon request 63 2½" 50-63KH004 L/L TOP 102 104 316 111
65-80 76 3" 65-80KH006 L/L TOP 102 129 371 111
100 102 4" 100-102KH006 L/L TOP 102 129 371 111
www.liag-valve.com 62
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORiES
Induktiver Näherungsschalter M12 aus Kunststoff,
24V DC für Antrieb Serie KH und KHG
Inductive proximity switch M12, plastic,
24V DC for actuator series KH and KHG
DN Typ Type
25 25 1" 25-102M55B
40 38 1½" 25-102M55B
50 51 2" 25-102M55B
65 63 2½" 25-102M55B
80 76 3" 25-102M55B
100 102 4" 25-102M55B
63
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORiES
3/2 Magnetventil mit Gerätesteckdose, für Edelstahlantrieb-Serie KH
3/2 Solenoid valve with cable plug, for stainless steel actuator series KH
DN Typ Type G L
25 25 1" 25-63MVB24D 24V DC G 1/8 6,5
25-63MVB110A 110V AC
25-63MVB230A 230V AC
40 38 1½" 25-63MVB24D 24V DC G 1/8 6,5
25-63MVB110A 110V AC
25-63MVB230A 230V AC
50 51 2" 25-63MVB24D 24V DC G 1/8 6,5
25-63MVB110A 110V AC
25-63MVB230A 230V AC
63 2½" 25-63MVB24D 24V DC G 1/8 6,5
25-63MVB110A 110V AC
25-63MVB230A 230V AC
65-80 76 3" 65-102MVB24D 24V DC G 1/4 9,5
65-102MVB110A 110V AC
65-102MVB230A 230V AC
100 102 4" 65-102MVB24D 24V DC G 1/4 9,5
65-102MVB110A 110V AC
65-102MVB230A 230V AC
DN Typ Type
Bestehend aus (für Serie KH):
8 x O-Ring aus NBR 25 25 1" 25-40KH002 DS
1 x Kolbendichtring 40 38 1½" 25-40KH002 DS 5
Consists of: 50 51 2" 50-63KH004 DS
8 x O-Ring NBR
63 2½" 50-63KH004 DS
1 x Piston seal
65-80 76 3" 65-102KH006 DS
100 102 4" 65-102KH006 DS
100 102 4" 65-102LKLASK*
* Dichtungssatz für Edelstahlantrieb Serie Alfa / Gasket set for stainless steel actuator series Alfa
www.liag-valve.com 64
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR Pneumatikantrieb mit Aluminiumgehäuse Serie B, luftöffnend/luftschließend, 0° - 90°
SPARE PARTS Pneumatic actuator with aluminium housing series B, air to open/air to close, 0° - 90°
AND ACCESSORiES DN L H Typ Type
25 25 1" 161 151 25-63KB50
40 38 1½" 161 151 25-63KB50
50 51 2" 161 151 25-63KB50
63 2½" 161 151 25-63KB50
65 - 80 76 3" 209 168 65-80KB50
100 102 4" 209 168 100-102KB50
150 6" 333 187 150KA50
Gehäuse mit PTFE Beschichtung auf Anfrage / PTFE coated housing upon request
65
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR Induktiver Näherungsschalter (Doppelsensor), 24V DC für Pneumatikantrieb Serie B
SPARE PARTS Inductive proximity switch (double sensor), 24V DC for pneumatic actuator series B
AND ACCESSORiES DN Typ Type
25 25 1" 25-102M55
40 38 1½" 25-102M55
50 51 2" 25-102M55
65 63 2½" 25-102M55
80 76 3" 25-102M55
100 102 4" 25-102M55
150 6" 25-102M55
5
65 63 2½" 25-102M55AT
80 76 3" 25-102M55AT
100 102 4" 25-102M55AT
150 6" 25-102M55AT
www.liag-valve.com 66
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR 5/2 Magnetventil mit Gerätesteckdose für Pneumatikantrieb
SPARE PARTS mit Aluminiumgehäuse Serie B
5/2 Solenoid valve with cable plug for pneumatic actuator
AND ACCESSORIES with aluminium housing series B
DN Typ Type
25 25 1" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
40 38 1½" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
50 51 2" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
63 2½" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
65-80 76 3" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
100 102 4" 25-102MVA24D 24V DC G 1/4
25-102MVA115A 115V AC
25-102MVA230A 230V AC
67
ERSATZTEILE Für Bogenventile For arc valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORIES
www.liag-valve.com 68
ERSATZTEILE Für Molchweichen For pigging valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORIES
Standard Handhebel, 3 x 120°
Standard handle, 3 x 120°
DN L1 h Typ Type
40 38 1½" 160 51 38-40SD506-120
50 51 2" 190 51 50-63SD506-120
63 2½" 190 51 50-63SD506-120
65 76 3" 190 51 65-80SD506-120
80 190 51 65-80SD506-120
100 102 4" 270 51 100-102SD506-120
69
ERSATZTEILE Für Molchweichen For pigging valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORIES
Induktiver Näherungsschalter (Doppelsensor), 24V DC für Pneumatikantrieb Serie B
Inductive proximity switch (double sensor), 24V DC for pneumatic actuator series B
DN Typ Type
40 38 1½" 25-102M55
50 51 2" 25-102M55
65 63 2½" 25-102M55
80 76 3" 25-102M55
100 102 4" 25-102M55
www.liag-valve.com 70
ERSATZTEILE Für Molchweichen For pigging valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORiES
71
ERSATZTEILE Für Molchweichen For pigging valves
uND ZUBEHÖR
SPARE PARTS
AND ACCESSORIES
40
DN
38 1,5" R 1/2
F Typ Type
38-40SDV505H
5
50 51 2" R 1/2 50-51SDV505H
63 2,5" R 1/2 63SV505H
65 76 3" R 1/2 65-76SDV505H
80 R 1/2 80DV505H
100 102 4" R 1/2 100-102SDV505H
www.liag-valve.com 72
73
Molchtechnik
Pigging System
www.liag-valve.com 74
6.1 DMV Molchsystem Für keimarme Verfahren und viskose, schnell aushärtende Medien
DMV Pigging System For low-germ processes and viscous, fast hardening media
75
DMV Betriebsverfahren DMV Lippenmolche
DMV operation procedure Zuverlässig in der Abdichtung
Einweg DMV Lippenmolche sind homogener Bau-
One way
art (hygienic design) mit hervorragender
Manuelle Molchrückführung
Manual return of pig Reinigungswirkung und annähernder
Verschleißfreiheit. Die Abdichtung erfolgt
Optional mit 3-A 101-00
Optionally with 3-A 101-00 zuverlässig über dynamische Lippen,
welche sich in Abhängigkeit des Schiebe-
Einfachschleife und Gegendrucks aufstellen und vorhan-
Single loop
dene Abweichungen in der Rohrleitungs-
Automatische Molchrückführung von Empfangsschleife
zur Sendestation, an-schließend manueller geometrie modellierend kompensieren.
Richtungswechsel Die Molche sind sehr flexibel und für enge
Automatic return of pig from receiving
to launching station, then manual change of direction Radien (R = 1,5 x D) geeignet. Dynamische
Lippenmolche sind optional mit eingegos-
senem Magnet zur Ortung und Steuerung
ausgerüstet und im Werkstoff Silikon mit
Zweiweg mit Wendestation FDA-Zulassung in den Nennweiten
Bi-directional with turning station
DN 40 – 100 (1.5" – 4") lieferbar.
Automatische Molchrückführung mittels
LIAG® Molchwendestation (geschlossenes System CIP/
SIP automatisiert)
Automatic return of pig by use of LIAG® turning station
(closed system CIP/SIP automated) Optional mit 3-A 101-00 DMV lip pig
Optionally with 3-A 101-00
For reliable sealing
Doppelschleife
DMV lip pigs are of homogeneous
Double loop (Bi-directional) construction (hygienic design). They offer
Automatische Molchrückführung excellent cleaning effect and are virtually
mittels LIAG® Molchweichen (geschlossenes System
CIP/SIP automatisiert)
free of wear. Dynamic lips form a reliable
Automatic return of pig by use of LIAG® pigging valves sealing. As a function of the pushing and
(closed system CIP/SIP automated)
counterpressure these lips accommodate
perfectly, thereby compensating existing
deviations in the pipe geometry. The pigs
Ringsystem
Ring system are highly flexible and suited for tight
Geschlossenes System CIP/SIP automatisiert radii (R = 1,5 x D). As an option, dynamic
Closed system CIP/SIP automated
lip pigs are equipped with a magnet for
location and control. They are FDA-rated
and available in silicone in the nominal
widths DN 40 – 100 (1,5" – 4").
www.liag-valve.com 76
6.1 DMV Molchsystem Für keimarme Verfahren und viskose, schnell aushärtende Medien
DMV Pigging System For low-germ processes and viscous, fast hardening media
77
DMV Molchtechnik
DMV Pigging System
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI 316L (1.4404 / 1.4435) with product: AISI 316L (1.4404 / 1.4435)
Andere Edelstahlteile: AISI 304 (1.4301) Other stainless
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, steel parts: AISI 304 (1.4301)
andere Qualitäten auf Anfrage O-ring seals: EPDM, FPM (Viton®), FEP,
Schließer Bogenventile other grades upon request
und Molchweichen: DyneonTM TFM1600, Shutter of arc valve and
alternativ: Tecapeek®, pigging valve: DyneonTM TFM1600,
PTFE+15% Peek alternatively: Tecapeek®,
DMV Lippenmolch: Silikon PTFE+15% Peek
DMV lip pig: Silicone
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Wichtiger Hinweis
Important note
6
DMV Molche dürfen nur in Systemen verwendet werden, die für diesen Molchtyp geeignet und ausgelegt sind. Der Her-
steller übernimmt bei unsachgemäßer Verwendung und Behandlung keine Funktionsgarantie, sowie keine Haftung für
Personen- und Sachschäden.
DMV pigs should only be used in pigging systems, which are designed for this type of pig. The supplier will not assume any
kind of function warranty or product liability and no responsibility for any kind of damage to persons or property due to
improper use.
www.liag-valve.com 78
DMV Molchsystem
DMV Pigging System
79
DMV Molchsystem
DMV Pigging System
www.liag-valve.com 80
6.2 SMV Molchsystem Für unkomplizierte Medien
SMV Pigging System For insensitive media
LIAG’s SMV pendulum pigging systems The components used in SMV pendulum Features
are based on the use of static pigs which pigging systems are essential to high • Hygienic design due to dead pocket
– driven by a pushing medium (product, operating safety. The use of ball valves minimized ball valves
water, air) – move back and forth between with minimized dead pockets is stan- • Various designs of SMV pigs
the pig launching and receiving station, dard in view of maximum process safety. and material available
thereby eliminating the remaining prod- As an option, static pigs are equipped • Suited for bends with radii R = 3,0 x D
uct from the pipe. SMV pendulum pigs with a magnet for location and control • The pig can be cleaned in the closed
are statically sealing by means of a de- and can be cleaned in the closed system system without removing
fined oversize between the pig outside without removing it. • SMV systems are optimally suited
diameter and pipe inside diameter. for insensitive media and liquids,
e.g. beverage, cosmetics, paint etc.
SMV Betriebsverfahren
SMV operation procedure
81
SMV Pendelmolch
www.liag-valve.com 82
SMV Molchtechnik
SMV Pigging System
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI 316L (1.4404 / 1.4435) with product: AISI 316L (1.4404 / 1.4435)
Andere Edelstahlteile: AISI 304 (1.4301) Other stainless
O-Ring Dichtungen: EPDM, FPM (Viton®), FEP, steel parts: AISI 304 (1.4301)
andere Qualitäten auf Anfrage O-ring seals: EPDM, FPM (Viton®), FEP,
SMV Pendelmolche: Silikon other grades upon request
SMV pendulum pigs: Silicone
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Wichtiger Hinweis
Important note
SMV Molche dürfen nur in Systemen verwendet werden, die für diesen Molchtyp geeignet und ausgelegt sind. Der Her-
steller übernimmt bei unsachgemäßer Verwendung und Behandlung keine Funktionsgarantie, sowie keine Haftung für
Personen- und Sachschäden.
SMV pigs should only be used in pigging systems, which are designed for this type of pig. The supplier will not assume
any kind of function warranty or product liability and no responsibility for any kind of damage to persons or property due
to improper use.
83
SMV MOLCHSYSTEM
SMV PIGGING SYSTEM
www.liag-valve.com 84
SMV Molchsystem
SMV Pigging System
85
Kugelhahn- DIN / SMS
molchweiche
120° Pigging
valves
Kugelhahn-Molchweiche, manuell, Gewinde DIN 11851
120° pigging valve (ball valve design), manual, male ends DIN 11851
DN Typ Type A B C D E
40 40DKV530M Rd65 x 1/6" 43 96 166 179
50 50DKV530M Rd78 x 1/6" 50 107 203 218
65 65DKV530M Rd95 x 1/6" 58 117 212 265
80 80DKV530M Rd110 x 1/4" 67,5 139 245 300
100 100DKV530M Rd130 x 1/4" 81,5 160 254 300
6
Kugelhahn-Molchweiche, pneumatisch, Gewinde SMS 1145
120° pigging valve (ball valve design), pneumatic, male ends SMS 1145
DN Typ Type A B C F G
38 38SKV530A Rd60 x 1/6" 43 96 270 259
51 51SKV530A Rd70 x 1/6" 50 107 301 289
63 63SKV530A Rd85 x 1/6" 54,5 123 356 347
76 76SKV530A Rd98 x 1/6" 67,5 139 356 382
102 102SKV530A Rd132 x 1/6" 81,5 160 389 382
www.liag-valve.com 86
87
Spezialarmaturen
Special Armatures
7.1 Rückschlagventile
Non Return Valves
7.3 Sichtgläser
Sight Glasses
www.liag-valve.com 88
7.1 Rückschlagventile
Non Return Valves
89
Technische Daten
Technical Data Overview
Werkstoffe Materials
Alle Edelstahlteile: AISI 316L (1.4404) All stainless steel parts: AISI 316L (1.4404)
O-Ring Dichtungen: EPDM, FPM (Viton®) O-ring seals: EPDM, FPM (Viton®)
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
Druck Pressure
Betriebsdruck: 20 bar max. (290 psi max.) Operating pressure: 20 bar max. (290 psi max.)
www.liag-valve.com 90
RÜCKSCHLAGVENTIL DIN
NON RETURN VALVE
91
RÜCKSCHLAGVENTIL SMS
NON RETURN VALVE
www.liag-valve.com 92
RÜCKSCHLAGVENTIL ERSATZTEILE FÜR DIN UND SMS
NON RETURN VALVE SPAREPARTS FOR DIN AND SMS
Feder, zylindrisch
Spring, cylindric
DN Typ Type
25 25 1" 25SD603B
40 38 1,5" 38-40SD603B
50 51 2" 50-51SD603B
65 63 2,5" 63-65SD603B
80 76 3" 76-80SD603B
102 4" 102S603B
Für Typen Rückschlagventile: XXD61A / XXD62A / XXS62A / XX62B
For types of non return valves: XXD61A / XXD62A / XXS62A / XX62B
Feder, konisch
Spring, conical
DN Typ Type
51 2" 51S622C
63 2,5" 63S622C
76 3" 76S622C
Für Typ Rückschlagventil: XXS62C
For type of non return valve: XXS62C
93
RÜCKSCHLAGVENTIL
NON RETURN VALVE
www.liag-valve.com 94
RÜCKSCHLAGVENTIL
NON RETURN VALVE
Führungsring oben
Upper guiding ring
DN Typ Type
25 25 1" 25SD601Y
40 38 1,5" 38-40SD601Y
50 51 2" 50-51SD601Y
65 63 2,5" 63-65SD601Y
80 76 3" 76-80SD601Y
102 4" 102S601Y
Für Typen Rückschlagventile: XXD61A / XXD62A / XXS62A / XXS62B / XXS62C
For types of non return valves: XXD61A / XXD62A / XXS62A / XXS62B / XXS62C
Führungsring unten
Bottom guiding ring
DN Typ Type
51 2" 51S601A
63 2,5" 63S601A
76 3" 76S601A
102 4" 102S601A
Für Typen Rückschlagventile: XXS62B / XXS62C
For types of non return valves: XXS62B / XXS62C
95
RÜCKSCHLAGVENTIL TC-CLAMP
NON RETURN VALVE
Rückschlagventil, 2x TC-Clamp
Non return valve, 2x TC-Clamp
oben / upper
DN Typ Type Ød ØD L p [bar]
1" 25C63A 22,2 50,5 60 0,18
1,5" 38C63A 34,9 50,5 62 0,12
2" 51C63A 47,5 64 70 0,08
2,5" 63C63A 60,2 77,5 80 0,05
3" 76C63A 72,9 91 90 0,05
4" 102C63A 97,6 119 138 0,05
4-fach geführte metallische Tellerdichtung
4-way controlled metallic disc seal
Feder, zylindrisch
Spring, cylindric
DN Typ Type
1" 25SD603B
1,5" 38-40SD603B
2" 50-51SD603B
2,5" 63-65SD603B
3" 76-80SD603B
4" 102S603B
Führungsring oben
Upper guiding ring
DN Typ Type
1" 25SD601Y
1,5" 38C633A
2" 51C633A
2,5" 63C633A 7
3" 76C633A
4" 102C633A
www.liag-valve.com 96
7.2 Drehverschraubungen mit & ohne Hub
Rotary Swivel Joint Fitting & Extending Rotary Swivel Joint Fitting
LIAG® Drehverschraubungen werden als LIAG® swivel joint fittings are designed as
drehbare Rohrverbindung eingesetzt. rotating pipe connection, e.g. in a flow panel.
Die radiale Abstützung erfolgt durch Teflon guided rings ensure radial shore.
Gleitringe aus Teflon. Zusätzlich können Additionally are the extending swivel joint
Drehverschraubungen mit Hub (X- und fittings able to compensate length extensions
Z-Achse) axial bis zu 75mm verschoben up to 75mm. LIAG® swivel joint fittings are of
werden. LIAG® Drehverschraubungen hygienic design and equipped with a leakage
sind hygienisch und haben eine Lecka- hole for visual inspection.
geöffnung zur optischen Kontrolle.
Merkmale Features
• Hygienisches Design • Hygienic design
• Leckageöffnung zur Sichtkontrolle • Leakage hole for visual inspection
• Kein Druckverlust • No pressure loss
• Molchbar mit LIAG® • Designed to be passed with
DMV Lippenmolch LIAG® DMV lip pig
• Radiale Abstützung für leichtes • Radial shore for easy turn
Verdrehen • 3-A 63-03 (COP)
• 3-A 63-03 (COP)
Drehverschraubung Drehverschraubung
ohne Hub mit Hub
Rotary Swivel Extending Rotary Swivel
Joint Fitting Joint Fitting
97
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI316L (1.4404) with product: AISI316L (1.4404)
Andere Edelstahlteile: AISI304 (1.4301) Other inox parts: AISI304 (1.4301)
O-Ring Dichtungen: EPDM, FPM (Viton®) O-ring seals: EPDM, FPM (Viton®)
Führungsring: Dyneon™ TFM1600 Steering ring: Dyneon™ TFM1600
Gleitring: Dyneon™ TFM1600 Slide ring: Dyneon™ TFM1600
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
Druck Pressure
Betriebsdruck: 10 bar max. (145 psi max.) Operating pressure: 10 bar max. (145 psi max.)
Anschlussarten Connection
Schweißende: DIN, SMS Welded ends: DIN, SMS
www.liag-valve.com 98
DREHVERSCHRAUBUNG DIN
OHNE HUB
ROTARY SWIVEL JOINT
FITTING Drehverschraubung ohne Hub, 2x Schweißende DIN11850
Rotary Swivel Joint Fitting, 2x welded ends DIN11850
DN Typ Type Ø D1 Ø D2 L
25 25D76S14 26 29 98
40 40D76S14 38 41 98
50 50D76S14 50 53 104
65 65D76S14 66 70 104
80 80D76S14 81 85 104
100 100D76S14 100 104 104
www.liag-valve.com 100
DREHVERSCHRAUBUNG DIN
MIT HUB
EXTENDING SWIVEL JOINT
FITTING Drehverschraubung mit Hub, 2x Schweißende DIN11850
Extending swivel joint fitting, 2x welded ends DIN11850
DN Typ Type Ø D1 Ø D2 Lmin Lmax
25 25D74S14 26 29 154 223
40 40D74S14 38 41 160 235
50 50D74S14 50 53 160 235
65 65D74S14 66 70 160 235
80 80D74S14 81 85 160 235
100 100D74S14 100 104 160 235
www.liag-valve.com 102
7.3 Sichtgläser
Sight Glasses
103
Technische Daten
Technical Data Overview
Werkstoffe Materials
Produktberührende Inox parts in contact
Edelstahlteile: AISI316L (1.4404) with product: AISI316L (1.4404)
Andere Edelstahlteile: AISI304 (1.4301) Other inox parts: AISI304 (1.4301)
Glaszylinder: Borosilikat (Duran®) Glass pipe: Borosilicate (Duran®)
Dichtungen: Silikon Seals: Silicone
Oberflächen Surfaces
Produktberührend: Ra ≤ 0,8 µm (Ra ≤ 32µin) In contact with product: Ra ≤ 0,8 µm (Ra ≤ 32µin)
Temperatur Temperature
Betriebstemperatur: 110°C (230°F) Operating temperature: 110°C (230°F)
Kurzzeitig: 140°C (284°F) Short-term: 140°C (284°F)
Druck Pressure
Betriebsdruck: 10 bar max. (145 psi max.) Operating pressure: 10 bar max. (145 psi max.)
Anschlussarten Connection
Schweißende: SMS Welded ends: SMS
www.liag-valve.com 104
SICHTGLÄSER SMS
SIGHT GLASSES
Rohrglas
Glass pipe
DN Typ Type Ø D1 Ø D2 L
25 25S651 22 28 76
38 38S651 35,6 42 96
51 51S651 51 58 106
63 63S651 61,5 70 126
76 76S651 72 85 146
102 102S651 96 110 196
105
7
www.liag-valve.com 106
107
7
Keine Haftung für Druckfehler. Änderungen vorbehalten.
107
liaG® – lÄuFER international aG – Am Wasserstall 12 – 88682 Salem / Germany
T +49 7553 59089 0 – [email protected] – www.liag-valve.com