Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Gaposa Qc20 Centralina Box
Gaposa Qc20 Centralina Box
CENTRALINA ELETTRONICA
Con Ricevitore Superetereodina 433 Mhz
Programmatore elettronico con ricevitore radio (433.92MHz rolling code) Italiano
per motori monofase di serrande avvolgibili e porte sezionali.
PULSANTE START CANCELLAZIONE TOTALE DEI CODICI
Deve essere di tipo NORMALMENTE APERTO e collegato tra i morsetti
Occorre procedere nel seguente modo:
11 e 13.
1 Disattivare l’alimentazione della centralina.
Il funzionamento è di tipo passo-passo.
2 Disabilitare la modalità rolling code DIP6=ON.
PULSANTE STOP 3 Premere il tasto SW1 e contemporaneamente riattivare
Deve essere di tipo NORMALMENTE CHIUSO e collegato tra i morsetti l’alimentazione. Il led lampeggia: rilasciare il tasto SW1.
12 e 13. Un suo impulso (apertura del contatto) bloccherà il motore in Tutte le zone di memoria (83) sono vuote e disponibili per una nuova
qualunque ciclo di funzionamento. programmazione.
N.B.: Se il Pulsante di STOP non è utilizzato ocorre cortocircuitare i
morsetti 12 e 13.
FOTOCELLULE DI SICUREZZA
CARATTERISTICHE TECNICHE
Collegate ai morsetti 13 e 14 comandano lo stop e l'inversione del moto
quando un qualsiasi ostacolo attraversa il loro campo di azione (per la Alimentazione 230VAC ± 10% 50-60Hz
varie modalità leggere sotto "PROGRAMMAZIONE DELLE VARIE Aliment. accessori esterni 24Vca 3W
Uscita motore 750W
FUNZIONI")
Temperatura d’esercizio -25°C ÷ +85°C
LAMPEGGIATORE/LUCE DI CORTESIA Dimensioni 205x160x85mm
Ai morsetti 7 e 8 si può collegare, con DIP1 OFF, il lampeggiatore (del Peso 800 g
tipo a 230V c.a. senza intermittenza) ed esso è attivo per tutta la durata
del ciclo. Si può altrimenti collegare, con DIP 1 ON, la luce di cortesia.
Questa rimarrà accesa fino a circa 2 minuti dopo l'arresto del motore.
COLLEGAMENTI ALLA MORSETTIERA
1 Alimentazione 230VAC
TEMPO DI PAUSA e CHIUSURA AUTOMATICA 2 Alimentazione 230VAC
Il temporizzatore di pausa, una volta attivato (DIP2 ON), consente la 3 Terra
chiusura automatica del motore dopo un dato periodo di tempo stabilito 4 Uscita motore Apertura
dall'utente. Agendo sul potenziometro P2 l'attivazione automatica del ciclo 5 Uscita motore Comune
di chiusura viene anticipata o ritardata (da un min. di 22 secondi ad un 6 Uscita motore Chiusura
max. di 180 secondi). 7 Lampeggiatore 230V max.40W
TEMPO DI LAVORO 8 Lampeggiatore 230V max 40W
Agendo sul potenziometro P1 è possibile regolare il tempo di lavoro da 9 Uscita 24Vac
circa 12 a 130 secondi 10 Uscita 24V ac
PROGRAMMAZIONE DELLE VARIE FUNZIONI 11 Ingresso pulsante di start (NA)
Agendo sui 6 dip switches presenti sulla scheda è possibile scegliere le 12 Ingresso pulsante di stop (NC)
s e g u e n t i particolari funzioni: 13 Ingresso comune (-)
ON 14 Ingresso fotocellula di sicurezza (NC)
15 Centrale antenna
16 Schermatura antenna
1 2 3 4 5 6 17
18 Pilotaggio Centralina di potenza
19
DIP1= Lampeggiatore/Luce di cortesia (vedi sopra)
DIP2= Chiusura automatica (vedi sopra)
DIP3= Comando di START in apertura
ON: la centralina non "sente"il comando di start in apertura
OFF: la centralina "sente" il comando di start in apertura
DIP4= disattivo
DIP5= Fotocellule di sicurezza
ON: attive anche in apertura
OFF: non attive in apertura
DIP6= Rolling code
ON: disabilitato
OFF: abilitato
LOGICA DI FUNZIONAMENTO
17 18 19
17
DIP1= Flashing light/Courtesy light (see above) 18 Links to QC3EMT and QC4EMM
DIP2= Closing time (see above) 19.
DIP3= START (opening cycle)
ON: the first impulse starts the motor. Further impulses
don't stop themotor until it reach the opening position
OFF: Further impulses stop and restart the motor in the
opening cycle
DIP4= disabled
DIP5= Safety beams
ON: attive anche in apertura
OFF: non attive in apertura
DIP6= Rolling code
ON: disabled
OFF: abled
17 18 19
FUNCTIONING LOGIC
The QC18 control unit functioning logic is semiautomatic (so-called step-
by-step operation): by using either the push-button or the remote
transmitter, the first impulse controls the opening of the rolling shutter,
until the working time is over. The second impulse controls the closing of
the rolling shutter; if an impulse arrives before the working time is over,
the unit will stop the rolling shutter and a further impulse will start again
the motor in the reverse motion.
REMOTE CONTROL PROGRAMMING
IMPORTANT: You have to keep a minimum distance of 1,5 metres
between the transmitter and the receiver
Please proceed as follows to programme the receiver:
1 Press the SW1 button until the L1 led lightens. IT IS NECESSARY
TO PROCEED WITH THE PROGRAMMING WITHIN 7 SECONDS.
2 Press the button of the transmitter until the L1 led goes off for about
½ a second indicating the right memorization of the code. Then the
led start flashing for a number of times corresponding to the number o
the memory area which has just been taken.
3 Once the flashings stop, the control unit and transmitter/s are ready to
be used
ROLLING CODE MODE
To activate the "rolling code" mode (that is the continuous changement of
the code at each transmission, according to a complex mathematical
QC20
CENTRALE ÉLECTRONIQUE
Avec Récepteur Superhéterodine 433 Mhz
Programmeur électronique avec récepteur radio (433,92 MHz rolling
code) pour moteurs monophasés de rideaux enroulables et portes francais
sectionelles.
TOUCHE START:
elle doit être de type NORMALEMENT OUVERT et connectée entre les EFFACEMENT TOTAL DES CODES
plots 11 et 13 ; le fonctionnement est de type pas à pas. Procéder de la façon suivante :
TOUCHE STOP: Désactiver l’alimentation de la centrale
elle doit être de type NORMALEMENT FERME et reliée entre les plots 12 Annuler la modalité rolling code DIP6=ONEnfoncer la touche SW1 et
et 13. Son enfoncement (ouverture du contact) bloquera le moteur en réactiver en même temps l’alimentation. Le voyant lumineux clignote :
n’importe quelle phase de son fonctionnement. relâcher la touche SW1.
N.B. : Si la touche STOP n’est pas utilisée, il faut court-circuiter les Toutes les zones de mémoire (83) sont vides et disponibles pour une
plots 12 et 13. nouvelle programmation.
PHOTOCELLULES DE SÉCURITÉ:
connectées aux plots 13 et 14, elles commandent le stop et l’inversion du
mouvement dès qu’un obstacle quelconque traverse leur champ d’action
(pour les diverses modalités, lire ci-dessous ‘’PROGRAMMATION DES
DIVERSES FONCTIONS’’). CARACTERISTIQUES TECHNIQUES
CLIGNOTANT / LUMIÈRE DE SERVICE: Alimentation 230VAC ± 10% 50-60Hz
on peut connecter aux plots 7 et 8 avec DIP 1 OFF, le clignotant (de type Alimentation accessories externes 24Vca 3W
à 230V o. a. sans intermittence) et celui-ci est actif pendant toute la durée Sortie moteur 750W
du cycle. Ou bien, avec DIP 1 ON, on peut connecter la lumière de Temperature d’utilisation -25°C ÷ +85°C
service. Celle-ci restera allumée encore 2 min environ après l’arrêt du Dimensions 205x160x85mm
moteur. Poids 800 g
TEMPS DE PAUSE et ARRÊT AUTOMATIQUE:
CONNEXIONS DE LA PLAQUE A BORNES
la minuterie de pause, une fois activée (DIP2 ON), permet l’arrêt
1 Alimentation 230VAC
automatique du moteur après un laps de temps déterminé par l’usager.
2 Alimentation 230VAC
Grâce au potentiomètre, P2, l’activation automatique du cycle de
3 Terre
fermeture peut être anticipée ou retardée (d’un mini. de 22 secondes à un
4 Sortie moteur ouverture
max. de 180 secondes).
5 Sortie moteur ordinaire
TEMPS D’EXÉCUTION: 6 Sortie moteur fermeture
en agissant sur le potentiomètre P1, il est possible de régler le temps 7 Clignotant 230V max.40W
d’exécution de 12 à 130 secondes environ. 8 Clignotant 230V max 40W
PROGRAMMATION DES DIVERSES FONCTIONS 9 Sortie 24Vac
Les 6 dip switchers (commutateurs) 10 Sortie 24Vac
présents sur le ON boîtier permettent de choisir 11 Entrée touche de Start (NA)
les fonctions particulières suivantes : 12 Entrée touche de Stop (NC)
13 Entrée ordinaire (-)
14 Entrée photocellule de sécurité (NC)
1 2 3 4 5 6
15 Centrale antenne
16 Blindage antenne
17
DIP1= Clignotant / Lumière de service (voir ci-dessus) 18 Commande centrale de puissance QC4EMM et QC3EMT
DIP2= Fermeture automatique (voir ci-dessus) 19.
DIP3= Commande de Start en ouverture
ON: la centrale ‘’n’entend pas’’ la commande de start en ouverture
OFF: la centrale ‘’entend’’ la commande de start enouverture
DIP4= désactivé
DIP5= Photocellules de sécurité
ON: actives aussi en ouverture
OFF: non actives en ouverture
DIP6= Rolling code
ON: annulé
OFF: inséré
LOGIQUE DE FONCTIONNEMENT
La logique de fonctionnement de la centrale QC20 est de type semi-
17 18 19