Pepper Construction Group’s Post

Multi flooring steel structure building installation

Sheet Metal Roofing What is metal sheet roofing? Several alternative methods of using metal as a roof covering are possible. However, metal may also be used to construct shingles, molded into shapes resembling tiles, shakes, or slates. The primary forms are based on sheet-like panels, which may be flat or profiled, either prefabricated or made on-site. Skilya’s standing seams or rolling joints are frequently used to link metal roofing sheets. These do not employ exposed mechanical fasteners; a unique protruding seam is created by a clipped or rolled pattern. This method, which may be used to make straight or curved seams, is adaptable and can be prefabricated or produced on location. Additionally, various built-up roofing systems, trims, and flashings are available to create valleys, ridges, roof lights, aprons, sills, corners, barges, and other architectural features. These historically associated with industrial buildings include profiled and corrugated metal roof panels, sometimes referred to as “wriggly tin,” as well as built-up roofing systems. Continue >> https://lnkd.in/dK8_63AW

A reinforced masonry wall is by ASCE 30-14, table 2-1 "Wall Systems" , is a "barrier wall system". Even without construction drawings available, the observations about stucco cladding weep screeds missing is irrelevant as they aren't required. It's a barrier wall, not a drainage system. Therefore, I would expect there to be barrier windows installed as well. I don't care if you're a "leading authority", you're still wrong. Now, I'm not suggesting the storefronts, which are designated by the manufacturer to be "wet sealed" or barrier windows as newly installed, were perfectly installed. They were not. But not picking up on either of those design intent facts brings the rest of your observations into question as well.

PBR metal panels are a low-maintenance, long-lasting alternative to traditional roofing and siding. The PBR panel profile provides additional weather protection by incorporating a purlin bearing leg that overlaps between panels, shutting out moisture and wind. These panels can be put on a solid substrate or on open framing like metal purlins or wood support beams. #metalsiding #metalroofing #metalfabrication #metalcladding #commercialconstruction #contractors #builders #roofers #architects #moderndesign #construction

Constructed from materials such as brick, stone, or concrete, these sturdy and resilient building exteriors have proven their ability to weather the test of time.   However, design and safety standards have evolved - and so have the passive fire protection and moisture management measures used to safeguard the lives and well-being of those using these buildings.   Our suite of factory-engineered passive fire and cavity tray solutions have been developed to help architects, fire engineers, and contractors meet the fire safety and damp-proofing requirements of their projects while yielding significant advantages in build program speed and sequencing. This includes ‘friction fitted’ cavity barriers to brickwork where ‘green’ mortar is not yet fully set, and ‘Euroclass A2-s1, d0’ cavity trays that don’t need soldering, sealants, or costly made-to-order prefabricated corner sections – which can comply with the requirements of the UK’s top #BuildingWarranty providers NHBC, LABC, and #PremierGuarantee.   The Siderise masonry range includes: ▪EW Cavity Barrier and Firestops ▪CT Cavity Tray ▪BB-FB Balcony Bracket   CTA see what our products can do for you https://lnkd.in/eDz-ukqN   #BrickBuilding #Construction #BuildingSafety #FireSafety

Building Knowledge: Self-levelling concrete and it’s use for correcting a dipped subfloor. This ties into my first post about floor prep. Humps are the primary problem when it’s time to prep for the finished floor installation. The opposite of this problem is a dip in the subfloor. These are less common to find than humps, but are equally or even more important to fix. Vinyl and engineered hardwood floors are often a floating floor system. This means the imperfections on the subfloor are easy to feel since the boards are not nailed or glued down. As these types of floors are so common, it’s critical that the subfloor is in perfect condition before their installation. During the floor prep, a dip can be spotted by seeing the gap between your straight edge (level) and the subfloor. These can be easy to miss, as with a hump the straight edge wobbles to indicate the imperfection. A dip however, must be seen by eye. Find the edges of the dip and then map out the affected area with spray paint. A dip of 1/4” is the maximum tolerance for hardwood/vinyl, 3/16” is the tolerance for carpet. Once the area is laid out, the subfloor is cleaned and a primer is applied. The primer prepares the area for the self-leveller, providing improved cohesion and coverage. The self-leveller compound is then mixed in a container with water until it reaches the right consistency. Not too thick, and not too runny. This is key as the product will not work as intended unless mixed properly. The self-leveller is then poured across the affected area and guided into position with a straight edge. With the straight edge, check the area by seeing if there is a gap underneath it. No gap, no problems. If there is then apply more self-leveller to the area. After 24 hours, the patch is now fully dry and ready for the installation of the finished floor. #Construction #NewBuild #SelfLeveller #Flooring

#45dayschallengeinconstruction What is COVER BLOCKS and Why they are provided. A cover block, also known as a cover concrete or topping concrete, is a layer of concrete placed over other building elements, such as: 1. Waterproofing membranes (to protect them from damage) 2. Insulation (to provide an extra layer of protection) 3. Structural slabs (to create a smooth surface) 4. Beams and columns (to conceal them and provide fire protection) The purpose of a cover block is to: - Protect underlying elements from weathering, mechanical damage, or chemical attack - Provide a smooth, even surface for finishing (e.g., flooring, painting) - Offer additional fire resistance or sound insulation - Enhance the aesthetic appearance of a building Cover blocks are typically made of concrete, and their thickness varies depending on the specific application and building codes. They can be cast-in-place or precast, and may contain reinforcement, like rebar or fiber mesh, for added strength. #buildingconstruction #coverblocks #bbs

Drywall or wallboard is in demand like other construction materials for interior finishing. It constitutes the overall construction projects and is used as per its acute requirement. To understand the aggregate materials and other requirements, you can have construction estimating services. But before using it, you need to keep out various concerns whether you are the project owner or the contractor. These concerns make sure that the material is properly installed and delivers the appropriate outcome. https://lnkd.in/dRnjzaS4 #construction #engineering #newyork #estimating #takeoff #building #drywall #renovation #remodeling #insulation

We might have some room for interested building practitioners who would like to attend a large bespoke test of a part of an external wall of a high-rise building early in the week of 18 December 2023. The question we will be addressing is whether or not a fire on one floor will jump to the floor above due to the existing combustible external cladding.   The building is  categorized as Class 2, 6, and 7a with a rise in storeys over 40. The exterior of the building is clad with ACP with varying polymer content ranging from 30-90%. In this test, we are assuming the worst case being 100% PE. Behind the ACP panels, there is a rockwool sandwich panel, then polyester insulation and plasterboard lining internally. We have instrumentations throughout the test rig, externally and internally including the cavities. There is also a concrete slab and spandrel (500 mm high x 150 mm wide) separating the two balconies, with a 110 mm bottom lip. There might not be enough fuel for a fire to spread to the upper floor, but we’ll find out If you'd like to attend, please write [email protected] by noon, Friday 15 December, 2023 and if there's room he'll make the appropriate arrangements.

How to cut extremely straight lines on your deck... Use a Fortress Building Products Evolution #Steel frame deck joist. Clamp to the deck in the appropriate place. Run the saw against it for a straight cut. Because steel stays straight. Track saw obsolete... Another way steel helps you build... #Better #Faster #Stronger StoneCroft Construction #Construction #Milwaukee #Milwaukeetools #tool #constructiontips #engineer #innovation #decks #deckbuilder