UC560 Quick Start
UC560 Quick Start
Welcome
Thank you for choosing the Cisco Unified Communications Model 560. The UC 560, part of the Cisco Smart Business Communications System (SBCS), is a unified communications solution for small businesses that provides voice, data, video, and security capabilities for up to 104 employees. This guide describes how to install the UC 560 hardware and how to connect to the UC 560 and launch the Telephony Setup Wizard provided with Cisco Configuration Assistant (CCA).
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
Before you begin the installation, make sure that you have the following: For Hardware Installation: Cisco IP phones One or more Power over Ethernet (PoE) switches for connecting IP phones or computers. We recommend that you use Cisco ESW 500 Series switches. Cables Ethernet cables (Category 5 or higher) for connecting IP phones and computers, WAN interfaces, or other devices. One Ethernet cable is included with the UC 560 and one cable is included with each IP phone. RJ-11 cable for analog Line (FXO) and Phone (FXS) connections. RJ-45 (non-Ethernet) cable for ISDN (BRI) connections. RJ-48 cable for ISDN (PRI) T1/E1 connections (only needed if a T1/E1 voice interface card is installed). You can purchase the RJ-45 and RJ-48 cables from your telephony service provider or reseller. The RJ-11 cable can be purchased from any electronics store. (Optional) Cable for connecting an external audio device to the 3.5 mm Music on Hold (MoH) port. (Optional) Additional Voice Interface Cards (VIC) to insert in the VIC slots.
Compact flash memory guard for protecting the compact flash memory slot. Included are two Torx T5 screws and a Torx wrench (size T5) for installing it. Mounting brackets and screws for mounting the unit in a 19 -inch rack.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
For Software Installation: A PC running: Windows Vista Ultimate, or Window XP (Service Pack 1) operating system Microsoft Internet Explorer 6.0 or later Adobe Flash Player with add-on version 10.0.0 or later
A registered account on Cisco.com. You need this so that you can download the CCA software necessary to configure your UC 560.
Assistant (CCA) before you install and configure your UC 560. See Installing Cisco Configuration Assistant, page 15. UC 560 Default Information
Attribute IP address Username Password Voice VLAN (100) Data VLAN (1) Smartports
Default Setting 192.168.10.1 cisco cisco 10.1.1.x 192.168.10.x GigabitEthernet 0/1/0 and 0/1/1 Role: cisco-switch, Native Vlan 1 GigabitEthernet 0/1/2 Role: cisco-desktop, Access Vlan 1
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
The UC 560 includes these features: 3 10/100/1000 Ethernet L2 expansion ports. 4 Line (FXO) ports or 2 ISDN (BRI) ports for Public Switched Telephone Network (PSTN) connections. The TI/EI model, in addition to the 4 Line (FXO) ports, provides digital T1/E1 connectivity options such as ISDN PRI or CAS connections to the PSTN. Music-on-Hold (MoH) audio port. 2 Expansion slots for Voice Interface Cards (VICs). The T1E1 model has only 1 open VIC expansion slot. 10/100/1000 Ethernet WAN uplink port Console port for command-line interface (CLI) access. This port can also be used for connecting to the CLI through a modem. Licenses to support 16 users (by default). You can increase the number of users on the system by purchasing and applying additional licenses. You can connect any Cisco ESW 500 Series switch to the UC 560 to connect phones and data devices. A number of models are available, including PoE and non-PoE versions. For information about the switches, see http://www.cisco.com/go/esw500help. The UC 560 can be installed in various types of network configurations. For guidance in planning, designing, and deploying the UC 560 in your network, use Cisco Smart Designs. Cisco Smart Designs are a collection of validated network designs and deployment best practices, that feature simple step-by-step implementation guidance specifically tailored for Small Business Solutions. See http://www.cisco.com/go/partner/smartdesigns.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
Front Panel
The front panel is where you connect the network devices. The ports on the panel vary depending on the model. There are three UC 560 Series model numbers: UC560-FXO-K9Base model with 16 user license, 4 Line (FXO) ports, and 2 VIC expansion slots UC560-BRI-K9Base model with 16 user license, 2 Line (BRI) ports, and 2 VIC expansion slots UC560-T1E1-K9Base model with 16 user license, 4 Line (FXO) ports, 1 T1/E1 controller, and 1 VIC expansion slot This illustration shows the front panel of the FXO model. Cisco UC 560 with Line (FXO) Ports
Line (FXO) ports Music on Hold Phone (FXS) ports VIC slots (2)
PC/EXP port
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195682
Feature
Music-on-Hold (MoH) audio port Console port
Description
Connects to an audio device (such as an MP3 player or radio) to provide streaming audio for music on hold. Connects the UC 560 to a console PC to provide access to the CLI. This port can also be used for connecting to the CLI through a modem. Recommended for advanced users or for device access recovery purposes. Provides dedicated WAN (Internet) access. Connects to a DSL router, cable modem, or other WAN connectivity devices LAN port that connects to a laptop or PC used for configuring the UC 560. This port can also be used as an expansion port. Connects to switches that have ports for phones or data devices. (We recommend that you connect the UC 560 to a Cisco ESW 500 Series switch.) Connects your phone system to the PSTN. (Only applies to models UC560-FXO-K9 and UC560-
WAN 10/100/1000 Ethernet port PC 10/100/1000 expansion port (PC/EXP) 10/100/1000 Expansion ports (2) Line (FXO) ports
T1E1-K9)
If the power fails, you can still make and receive emergency calls if you have a telephone line connected to the Line (FXO) port 0 and an analog phone connected to the Phone (FXS) port 3, even if the unit is not powered on. Connects directly to an analog telephone, fax machine, or similar device. Connects the UC 560 to an Integrated Services Digital Network (ISDN). Only applies to model UC560-BRI-K9. Storage that contains the UC 560 software image and default configuration values and phone software. Storage that contains the voicemail software, embedded application software, and stored messages. Provides connectivity to a Public Switched Telephone Network (PSTN) for additional phone ports.
Phone (FXS) ports ISDN Basic Rate Interface (BRI) ports IOS Compact Flash Voicemail Compact Flash (Optional) Two Voice Interface Card (VIC) expansion slots
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
Back Panel
The back panel is where you connect the UC 560 to power. There is no external On/Off power switch on the unit.
LEDs
The LEDs on the front panel of the UC 560 are used for monitoring system activity and performance.
SYS
VM
LED SYS
Description Indicates that the system has successfully booted and is ready to use. The LED flashes green while the system is booting and then turns solid green when booting is complete.
VM
Indicates that voice mail is active. The LED is solid green when voice mail is active. WAN, PC/EXP, and Each port has a right and left LED. The left flashes EXPANSION Ports green when there is activity on the port. The right LED is solid green when the connection is active. Compact Flash Flashes green when the compact flash is accessed. (CF) Otherwise, the LED is off.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195674
Before you install the UC 560, review the Regulatory Compliance and
Safety Information for Cisco Unified Communications 500 Series Model UC 560 for Small Business on your product CD.
NOTE Only install supported Voice Interface Cards (VICs) into the VIC
expansion slot of the UC 560. For a list of these cards, see the
of the device.
Rack Mounting
You can mount the UC 560 in any standard size, 19-inch (about 48 mm) wide rack. It requires 2 rack units (RU) of space, which is 3.50 inches (9 mm) high.
Placement Tips
Ambient TemperatureTo prevent the device from overheating, do not operate it in an area that exceeds an ambient temperature of 104F (40C). Do not block or cover the vents. Air FlowMake sure that there is adequate air flow around the device. Mechanical LoadingCheck that the device is level and stable to avoid any hazardous conditions. Reliable GroundingMake sure that the unit is grounded and uses suitable electrical supply connections.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
supplied screws and secure the bracket tightly. Do not overtorque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m).
STEP 2 Follow the same steps to attach the other bracket to the opposite
side.
STEP 3 After the brackets are attached to the unit, use suitable screws to
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195677
ground lug or terminal. For the ground lug, strip approximately 0.75 in. (20 mm). For the user-provided ring terminal, as required.
STEP 2 Crimp the ground wire to the ground lug or ring terminal, using a
STEP 4 Connect the other end of the ground wire to a known reliable earth
ground point. If there is any doubt as to the reliability of the ground point, contact a licensed electrician for assistance.
10
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195675
Panel, page 5.
STEP 2 Slip the right tab on the CF-Guard into the slot on the right side of
the attachment screw on the left side of the CF-Guard with the screw hole in the panel.
STEP 4 Tighten the attachment screw on the left side of the CF-guard by
and running.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195673
11
STEP 1 Insert the power cord into the back of the UC 560. Do not connect
to power.
STEP 2 Connect the interfaces and devices as described below.
Description Connect the supplied Ethernet cable from the broadband network device to the WAN port on the front panel of the UC 560. Cisco strongly recommends using devices. Category 5 or better cable. PSTN analog trunks Connect an RJ-11 cable to one of the Line (FXO) ports on the front panel of the UC 560. Connect the other end of the cable to a PSTN line or a station interface on a PBX. Fax machine or analog Connect an RJ-11 cable to one of the Phone phone (FXS) ports on the front panel of the UC 560. Connect the other end of the cable to the fax machine or phone. ESW switch Connect an Ethernet network cable from one of the expansion ports of the UC 560 to one of the uplink ports on the switch. Connect an Ethernet network cable to one of IP phones and other network devices (such as the ports on the ESW switch. a wireless access point, IP video cameras, and network attached storage (NAS) devices) ISDN line1 Connect the cable provided by the ISDN (only applies to model provider to one of the Line (BRI) ports on the UC560-BRI-K9) front panel of the UC 560. Connect the other end of the cable to the ISDN provider equipment.
1. If a T1/EI controller is installed in the VIC slot, connect either a T1/E1 straight-through cable (identical to the Ethernet straight-through cable), or a T1/E1 crossover cable to the controller. Connect the other end of the cable to the ISDN provider equipment. The cable that you use depends on the type of termination on the network interface device (NID), and is the point in which the telephone company network ends and connects with the wiring at the customer site.
12
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
STEP 3 Power on the UC 560 by inserting the power cord plug into a
192.168.10.x
IP
IP
Fax
PC Analog phone
195676
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
275432
13
To verify the hardware installation, complete the following tasks: Check the status of the UC 560 by looking at the LEDs on the front panel See LEDs, page 7. Check that the switch is connected is connected to the expansion port. To test IP connectivity, launch a Web browser and enter http://192.168.10.1. When the authentication window appears, this means that your system is active. Make sure that each connected IP phone displays an internal extension number or a line number, on at least one of the phone line buttons. Verify the phone connectivity by making a call from one phone to another.
Business Support Community website at: http://www.cisco.com/ go/smallbizsupport. For technical documentation and other links, see Suggested Next Steps, page 19 and Where to Go From Here, page 20.
14
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
After you install the UC 560, you configure it by using Cisco Configuration Assistant (CCA). CCA is an easy to-use application used to configure, manage, and administer your UC 560 and other devices in the Cisco Smart Business Communications System. It provides everything you need to quickly set up a small office network.
NOTE Only use CCA to configure your device. Using the Command-
required.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
15
of the UC 560. Connect the other end of the cable to the Ethernet port on your PC. Verify that the PC is set to use the Dynamic Host Configuration Protocol (DHCP) to obtain its networking parameters (such as IP Address, Subnet Mask, Default Gateway, DNS Server, and so forth).
This is the preferred way to connect to a Cisco Smart Business Communications System (SBCS).
STEP 3 Enter the name and description for the new customer site. STEP 4 From the Discover Devices drop-down menu, select Using a
Starting IP address.
16 Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
195681
UC 560 and click OK. The default username is cisco and the default password is cisco. Passwords are case sensitive.
STEP 8 If prompted for the login information for a connected ESW switch,
enter the switch username and password. CCA will automatically discover the device. The switch default username is cisco and the default password is cisco.
STEP 9 When CCA discovers both the UC 560 and ESW switch (if
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
17
STEP 1 Click Next and follow the prompts to complete the installation. STEP 2 After the wizard completes:
Verify Internet connectivity by going to: http://www.cisco.com. Test calls to and from the PSTN. Test calls to voice mail and Auto Attendant (AA), if configured. Verify that the IP phones show the correct date and time.
NOTE The Wizard requires that you change the default administrator
login and password. Use the new username and password to access and administer the UC 560. Congratulations! The basic installation of the UC 560 is complete.
18
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
You are now ready to start using your UC 560. Depending on how you plan to use the UC 560 in your network, here are some suggested next steps to take.
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
19
8
Support
Cisco Small Business Support Community Online Technical Support and Documentation (Login Required) Phone Support Contacts
http://www.cisco.com/go/smallbizsupport http://www.cisco.com/support
http://www.cisco.com/en/US/support/ tsd_cisco_small_business_support_center_contacts .html Go to http://www.cisco.com/public/sw-center/ index.shtml and enter the model number in the Software Search box.
Cisco IP Phones
Cisco IP Phone SPA 500 Series Cisco IP Phone SPA 525G Deployment Guide Cisco IP Phone Quick User Guides Cisco Unified IP Phones 7900 Series http://www.cisco.com/en/US/products/ps9730/ index.html http://www.cisco.com/en/US/docs/voice_ip_comm/ sbcs/deployment_guides/spa525g_phone/ sbcs_spa525g_wireless_deployment_guide.pdf http://cisco.com/go/sbcs-docs http://www.cisco.com/en/US/products/hw/phones/ ps379/
http://www.cisco.com/smb http://www.cisco.com/go/marketplace
20
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
21
22
Cisco Unified Communications 500 Series Model UC 560 Quick Start Guide
Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) 2009 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste.
78-19200-01