Professional Documents
Culture Documents
CVT Transmission Part2
CVT Transmission Part2
JATCO CVT and DaimlerChrysler Electronic and Computer Part 2 Control Systems
ratio to reduce engine RPM, the stepper motor (1) moves out, which moves the ratio control valve (2) out. This allows line pressure to enter the primary variator (4). The additional pressure entering the primary variator causes the variator halves to squeeze together, causing the belt to ride toward the outer diameter (simulate large gear). Once the primary variator moves enough to satisfy the TCM, the ratio control valve moves back into the hold position. The position of the ratio control valve depends on the position of the variator and the stepper motor. The TCM can alter the ratio by actuating the stepper motor, letting the variator change until it moves the ratio control valve back into the hold position. This is possible because these three components are linked together mechanically. The fluid release in the secondary variator is controlled by the secondary pressure control solenoid and valve (3). As this solenoid is actuated, the pressure trapped in the secondary variator (5) can either exhaust, or line pressure can be directed to it to increase the clamping load. This is all controlled by the TCM. During the ratio change from low to high, the secondary variator pressure exhausts to allow the ratio change. Once the change is complete, line pressure is once again directed into the secondary variator to provide clamping load (Figure 3). When shifting from high to low ratio, the TCM moves the stepper motor in, which moves the ratio control valve
by Sean Boyle
n the last issue of GEARS, we began looking at the JATCO Continuously Variable Transmission (CVT) being offered with the 2007 Jeep Compass, Patriot, and Dodge Caliber. We examined its basic construction, and discussed powerflow through the unit. In this issue, were going to look into the electronics and control systems used to operate this new transmission, beginning with the valve body.
Valve Body
The JATCO CVT valve body consists of pressure sensors, variator pressure solenoids, torque converter clutch solenoids, and a unique stepper motor for controlling the pressure split between the primary and secondary variators. The stepper motor works (1) in conjunction with the Ratio Control Valve and (2) as a mechanical link, which connects the ratio control valve and stepper motor to the primary variator (4). The ratio control valve works in three different modes: feed, hold, and vent. These modes detemine the ultimate position of the variators and control the resulting ratios (Figure 1). When the TCM is satisfied with the ratio and the position of the variators, the ratio control valve (2) is in the hold position. Line pressure from the pump is fed into the secondary variator (5) to establish the necessary clamping force on the belt (Figure 2). When the TCM wants a higher 4
Windings & terminal connections impervious to contamination Plastic fully encloses lead wire for support Plastic fully surrounds coil Extended Sure-Signaltip ensures stronger signal
964 East Market St., Crawfordsville, IN 47933 Toll Free: 800-729-7763 Fax: 765-364-4576 Email: [email protected] www.raybestospowertrain.com
Figure 6 1 2 3 4 5 6 Secondary Pulley Control Clutch Reducing Regulator Valve Lockup Control Select Switch Valve Select Control Valve Solenoid Regulator Valve
Figure 4
into the vent position. The fluid in the primary variator exhausts, which allows the sheaves to spread and allows the belt to ride toward its inner diameter. The secondary variator is still fed line pressure, which in turn causes it to squeeze the sheaves together, making the belt ride toward its outer diameter. The net result is a lower gear ratio. Once the ratio has changed enough to move the ratio control valve into the hold positon, pressures are stabilized between the primary and seconary variators. Obviously, this can happen at any speed and any engine RPM. The TCM uses electical inputs, such as throttle position, manifold absolute pressure, fluid temperature, speed sensors (CKP, ISS, OSS), pressure sensors, range sensor, etc., to determine the proper ratio. So far weve looked primarily at the ratio control valve and the secondary pressure control valve, but the 6
Figure 7 1 2 3 4 5 Figure 5 Secondary Pulley Regulator Pressure Regulator 1 Pressure Regulator 2 TCC Regulator Valve Manual Valve
JATCO CVT has a few other very important valves. Pressure regulator type valves: The oil pump (Figure 4) has the ability to generate over 1000 PSI, but not everything in the CVT needs this much pressure. Because 800+ PSI is more than most circuits need, line pressure is regulated down to three lower levels. 1) 218 PSI max for the clutches 2) 145 PSI max for the TCC 3) 60 PSI max for the lube and cooler circuits The line pressure regulator valve (Figure 5) determines the overall highest pressure in the transmission. All
Figure 8
other pressures originate from line pressure, which can vary between 72 and 870 PSI, depending on operating conditions. The pressure is controlled GEARS April 2007
Figure 10
Figure 9 1 2 3 4 5 6 TCC Lockup/Select Switch Solenoid TCC Control Solenoid Secondary Pressure Solenoid Line Pressure Solenoid Primary Pressure Sensor Secondary Pressure Sensor 7 Stepper Motor 8 Ratio Control Valve 9 Ratio Control Link 10 ROM 11 Transmission Temperature Sensor
by the line pressure control solenoid, which is pulse width modulated (PWM) and high-side (B+) driven by the TCM. Line pressure is fed directly to the ratio control valve and the secondary valve to influence ratios and belt side loads (Figure 6). The Valve body has a number of Screens and Valves (Figure 7 and 8). The clutch reducing regulator valve lowers line pressure to 15 218 PSI to accomodate the forward and reverse clutches. These pistons only need enough pressure to apply adaquate force on the clutch packs to prevent them from slipping. When engaging drive or reverse, the TCC/clutch control PWM solenoid modulates to allow for smooth clutch apply. Once the vehicle is in gear, the select switch/TCC lockup solenoid allows the TCC/clutch control PWM solenoid to modulate the torque converter clutch apply and release. The TCC/clutch control solenoid controls the apply pressure to the torque converter clutch. Once the TCC lockup control valve shuttles to the apply position, apply pressure regulated by the TCC/clutch control solenoid enters the torque converter. The regulated pressure allows for seamless application of the torque converter clutch. The pressures in the TCC apply circuit can vary between 0 to 145 PSI. Unlike the Honda CVT, the JATCO CVT uses a torque converter. The purpose of the torque converter is to allow smooth acceleration from a standstill by providing a hydraulic disconnect from the engine. After rolling away from a stop sign, the torque converter clutch applies very early, usually at about 12 MPH. Some of the advantages of a CVT include increased efficiency of power transfer and unlimited ratios, so the transmission control module (TCM) makes the most from the CVT by locking the converter as early as possible.
Figure 11
JATCO CVT and DaimlerChrysler, Part 2 ety of DTCs will set depending on a circuit or mechanical failure with the line pressure Cav Color Function Measurements solenoid: DTCs P0746, 1 DG/LB Line Press Sol PWM 3 9 ohms P0962, P0963. 2 YL/DB Sec Press Sol PWM 3 9 ohms 3 YL/LB TCC Sol PWM 3 9 ohms The Secondary 4 YL/GY TCC On/Off 10 15 ohms (a) Variator Pressure 5 PK/LB 5-Volt Supply 5 volts Control solenoid con6 BK Ground trols the position of 7 PK/LB Sec Press Signal 0.7 3.5V (b) 8 LB/YL Motor C 10 20 ohms the secondary variator 9 YL/OR Motor A 10 20 ohms pressure control valve. 10 YL/WT Motor B 10 20 ohms This valve regulates the 11 TN/YL Motor D 10 20 ohms release of fluid from 16 YL/LB Chip Select for ROM 17 RD/WT Trans Temp Signal 5k ohms at 75F the secondary variator 18 DG/YL Primary Press Signal 0.7 3.5V (b) during movement from 19 DG/VT Sensor Ground high ratio to low ratio. 21 DG/BR Clock Select for ROM Since the CVT relys on 22 GY/YL Data In/Out for ROM the secondary variator (a) Observed 26.5 ohms on training center bench unit to provide the neces(b) Pressure transducers will output a varying voltage sary clamping force based on pressure. Monitor pressure with a scan tool then compare to actual pressure gauge readings. In neutral with on the belt, its very the engine running, expect between 0.7 and 3.5 volts from important for this solethe primary, and around 1 volt from the secondary. noid and valve assembly to work properly. Electronics The following DTCs will set if The CVT has three PWM sole- theres a failure in the Secondary Variator noids: Line Pressure, Secondary Variator circuit or valve: DTC P0776, P0777, Pressure, and Torque Converter Clutch/ P0966, and P0967. The TCM will look Clutch Engagement. In addition to the at the secondary variator pressure sensor PWM solenoids, the CVT has a single to determine if the solenoid is operating on/off solenoid for the TCC lockup/ properly. If the actual and target presselect switch valve (Figure 9). sures dont match, a DTC will set. The line pressure PWM solenoid While reviewing the wiring schecontrols the position of the line pressure matic, you might notice the ROM assemregulator based on TCM decisions. The bly. This is a chipset programmed when typical resistance of the line pressure the transmission was assembled and solenoid is between 3 9 ohms. A vari- carries vital information on the varia-
tors and hydraulic system. The ROM should never be interchanged with any other CVT. It is unique to the CVT it came with. In fact, if you exchange a CVT while reusing the original TCM, or swapping the original TCM with a used one, a calibration mismatch code P167A will set. In that case, youll have to use a factory scan tool to go through a calibration procedure to recalibrate the TCM and ROM. If you install a new TCM, a DTC P1679 calibration not learned will set, which will also require a recalibration using a scan tool. Regardless, it is important that the ROM assembly be kept with its original transmission. The Transmission connector (Figure 10) has 22 pins but not all of the pins are used. These JATCO CVT equipped vehicles use the Controller Area Network (CAN) heavily for module-to-module communication (figure 11). The CAN is capable of sending up to 1 Mb/s of information across two wires, including vital sensor info such as TP, MAP, ECT, CKP, ect. When reviewing the TCM schematic, notice there are no dedicated circuits for engine speed, throttle position or load. The TCM relies on the CAN for these essential inputs. Since the CVT is only available in new model vehicles that use the CAN bus, its imperative that your scan tool be CAN capable. The DaimlerChrysler StarScan or StarMobile will undoubtedly have the most features available for diagnostics.
DTC
P0219 P0571
DESCRIPTION
Engine Overspeed Brake Switch
NOTES
Sets when CAN bus detects engine speed over 6800 RPM. Sets if the brake switch status doesn't change but the computer registers MPH. This needs to fail in two consecutive key cycles to set a DTC. Beware two footed drivers. TCM doesn't receive valid vehicle info from FCM. Probably set from using a different module for the TCM. FCM/TIPM Pressure sensors have less than 0.05V. Open or short to ground in sensor supply circuit. Continuous loss of valid signal. Takes two failures to set a DTC. TCM receives more than two valid TR signals. Trans temp doesnt change for 10 minutes or the calculated vs. actual temp varies by more than 104F. Scan tool indicates 356F. Short to ground, sensor failure, 68F = 2.5k 6.5k ohm, 176F = 300 900 ohms. Scan tool indicates 40F. Short to power, open, sensor failure.
Control Module Programming Error/Not Programmed ECU Vehicle Options Mismatch Sensor Reference Voltage Circuit Transmission Range Sensor Circuit Low Transmission Range Sensor Circuit High Transmission Temp Sensor Performance Transmission Temp Sensor Low Transmission Temp Sensor High
COMPLAINT
SECONDARY COMPLAINTs
Cause
These problems can be caused by severe wear of the boost valve sleeve, allowing EPC and reverse oil leakage.
TOTOTA U241E
COrrection
The Sonnax boost valve assembly has upgraded materials and minimal clearances to prevent wear and restore proper hydraulic control.
Primary Regulator Valve
Shim
Spring
Boost Valve
Plug Pin
89010-01K 89010-02K
A540
89031-01K 89031-02K
Toyota vehicles with a U241E transmission may exhibit insufficient line rise in the drive ranges and excessively high pressures in reverse. This can be caused by continuous oscillation of the steel boost valve within the cast-aluminum sleeve, creating excessive wear and a path for EPC and reverse pressures to leak. This leakage is further aggravated by the thermal expansion mismatch of the valve and sleeve materials. The Sonnax replacement boost valve assembly, 57917E-01K, has upgraded and more closely matched materials, with minimal clearances to prevent wear and restore proper hydraulic control. The boost sleeve is manufactured from highly wear-resistant billet aluminum to prevent the excessive wear exhibited by the cast OEM sleeve, and the assembly restores proper line rise.
See your nearest Transmission Specialties distributor & ask for Sonnax quality engineered products.
Automatic Drive P.O. Box 440 Bellows Falls, VT 05101-0440 USA 800-843-2600 802-463-9722 F: 802-463-4059 www.sonnax.com [email protected]
DTC
P0716
DESCRIPTION
ISS Circuit Performance
NOTES
All must be met for this DTC: CKP-Pri RPM > 1000 RPM (Sec RPM x Est. Ratio) - Pri RPM > 1000 RPM (CKP-Sec RPM) x Est. Ratio < 1000 RPM If OSS DTC sets there might be an issue with power. Both sensors are fed 12V from TIPM. Hall Effect: center terminal toggles 5V to ground. All must be met for this DTC: CKP-Pri RPM > 1000 RPM (Sec RPM x Est. Ratio) - Pri RPM > 1000RPM VSS - VSS Est. (using Sec RPM) 12.5 MPH If OSS DTC sets there might be an issue with power. Both sensors are fed 12V from TIPM. Hall Effect: center terminal toggles 5V to ground. Sets when a difference between actual and target ratio exceeds 1000 RPM for 5 seconds. Excess TCC slip detected for 30 seconds. Takes two failures to set a DTC. A ratio of 2.7:1 detected for 0.2 second or 3.5:1 detected for 0.1 second. This would indicate a slipping belt.
P0717 P0721
P0722 P0730 P0741 P0746 P0776 P0777 P0826 P0842 P0843 P0847 P0848 P0962 P0963 P0966 P0967 P161B P1661 P1679 P167A P1702 P1723 P1729 P2769 P2770 U0001 U0100 U0121 U0141
OSS No Signal Incorrect Gear Ratio TCC Circuit Performance Line Pressure Solenoid Performance
Secondary Pressure Solenoid Stuck Off (High Difference between actual and target pressure is over 174 PSI for 30 secPressure) onds. Secondary Pressure Solenoid Stuck On (Low Pressure) Up/Downshift Switch Circuit (Autostick Switches) Primary Oil Pressure Circuit Low Primary Oil Pressure Circuit High Secondary Oil Pressure Sensor Low Secondary Oil Pressure Sensor High If actual is lower than target by 36 PSI for at least 1.5 seconds twice within a 30 second window, or if actual is 291 PSI less than target for 800 ms. Sets when the upshift and downshift switches are closed at the same time or the switches are closed when the shifter isn't in drive. Sets when voltage drops below 0.09V for 5 seconds. Sets when voltage rises above 4.7V for 5 seconds. Sets when voltage drops below 0.09V for 5 seconds. Sets when voltage rises above 4.7V for 5 seconds.
Pressure Control Solenoid A Circuit Low (Line Press Check for short to ground and lack of power output from TCM. High side drivSolenoid) ers in the TCM. Pressure Control Solenoid A Circuit High (Line Pressure Check for opens and high resistance. TCM monitors current flow. Solenoid) Pressure Control Solenoid B Circuit Low (Secondary Check for short to ground and lack of power output from TCM. High side drivPressure Solenoid) ers in the TCM. Pressure Control Solenoid B Circuit High (Secondary Pressure Solenoid) Battery Disconnect/TCM Internal Sensor Ground Reference High Calibration Not Learned Calibration Mismatch Primary Oil Pressure Sensor/Secondary Oil Pressure Correlation Lockup/Select Control Circuit Transmission Ratio Control Circuit (Stepper Motor) TCC Circuit Low TCC Circuit High CAN C Bus Lost Communication with PCM Lost Communication with ABS Lost Communication with IPM (FCM/TIPM) Check for opens and high resistance. TCM monitors current flow. Sets with a loss of power to the TCM. Check for opens or short to B+ on the sensor ground circuit. New TCM installed. Swapping TCMs or Transmissions. Comparison between valid signals between the two sensors. Invalid electrical voltages. Invalid electrical voltages. Check for short to ground and lack of power output from TCM. High side drivers in the TCM. Check for opens and high resistance. Communication network problem. Might not get communication with scan tool if the problem is present. Check connections and see if other modules can communicate. Check connections and see if other modules can communicate. Check connections and see if other modules can communicate.
Although it may be a while before you see one of these CVTs in your shop, its definitely time to get ready for this technology. CVTs could very well be the next trend for the automatic transmission industry. Six, seven, and 10
even eight speed transmissions are rolling off the assembly line every day, but theyll never achieve the infinite number of ratios found with a CVT. With that said, there are a few things holding back a widespread CVT
market right now, including weight, torque capacity, and ratio-change speed. And at the rate technology is increasing, dont be surprised to see these issues addressed very soon. GEARS April 2007
Their Kits.
1. Price
2. More Parts.
We offer more parts and sell more parts than any other kit supplier. Every 12.7 seconds someone, somewhere, rebuilds a transmission with a TransTec kit. Thats 24 hours a day, 7 days a week, 365 days a year... and that doesnt even include our O.E. service kits.