Measurement of Bulk Cargoes - Draught Surveys
Measurement of Bulk Cargoes - Draught Surveys
MAY 2008
- Vessels which are lying at a river berth or in tidal conditions when strong currents are running. Under these conditions the draught marks should ideally be read over periods of slack water (provided that at a low water slack there is sufficient under-keel clearance). - Currents of appreciable strengths are likely to cause the vessel to change trim or pitch slightly and/or sink bodily into the water from her static draught (squat). This phenomenon becomes more pronounced in shallow waters (shallow water effect). - Strong currents will result in raised water levels against the leading edge of a stationary vessel lying in flowing water. This is especially true when the flow is in the direction of a vessels bulbous bow. Draught marks must be read on both sides of the vessel: forward port and starboard; amidships port and starboard, and; aft port and starboard or, alternatively, if additional marks are displayed on large vessels at all the designated positions. Should draught marks not be in place amidships, distances from the deck line to the water line on both sides of the vessel must be measured. The amidships draughts can then be calculated from load line and freeboard data extracted from the vessels stability booklet. Draught marks should be read with the observer as close to the water line as is safe and reasonably possible, in order to reduce parallax error. Although it is common practice to read the offside draught marks from a rope ladder, a launch or small boat provides a more stable environment and brings the observer to a safer position closer to the water line. A vessels remote draught gauge should never be used for surveys, due to lack of the necessary accuracy and the possibility of errors, which may accumulate over the working life of the instrument. When adverse weather conditions are being experienced, access to the offside draught marks may prove difficult or impossible. At these times the draughts on the nearside can be read and the offside draughts calculated using a manometer (Addendum 1). This method should never be used when the offside draughts can be safely observed and accurately read. If, as a final resort, this method cannot be undertaken, the use of a fully calibrated inclinometer, graduated to minutes of arc, is strongly recommended. The type of inclinometer fitted to vessels is not usually of sufficient accuracy to be used.
Above: Manometer showing plastic tubing (30-40 m long), fitted at each end with a valve and scale.The valves are to allow the water in the tube to be retained without any air bubbles in it when the device is not in use. Below: Manometer, showing scale and water level.When a scale is fitted and used for the reading care must be taken that the scale is fixed at the same height on each side.
be taken. In order to overcome the problem of layering, the samples should be obtained using a closed sampling can at a depth of approximately half the existing draught of the vessel. Alternatively, a slowfilling container can be used to obtain an average sample from keel to waterline. When reading the hydrometer floating in the sample of water, the eye of the observer should be as close to the water level as possible, to avoid parallax errors and also to avoid further errors due to the meniscus (Addendum 2).
The relative density of the contents may be calculated using the following formula: RD of tank contents at survey = (Old oil volume x Old RD) + (New bunker volume x New RD) Total volume of oil in tank After completion of the bunker survey the totals of each oil found must be agreed with the chief engineer and the master.
Documentation
At completion of survey, a survey work sheet or computer printout should be placed on board the vessel recording the data and calculations used to obtain the cargo loaded/ unloaded quantity. This document is usually produced by individual survey companies, or by shipping companies for use by their officers. A formal survey report should be submitted to clients at a later date. Specific formal documentation has been drawn up, amongst others by IMO, United Nations Economic Commission for Europe and various P&I Clubs. The formal report document should not only include details of the survey, but also: Dates and times of surveys. Vessel particulars. Ships location. Weather conditions (and whether these were within acceptable limits). Sea conditions (and whether these were within acceptable limits). Tidal/current conditions (and whether these were within acceptable limits). A record of any difficulties or defects in a ships documentation or equipment which might cause the calculated weight by draught displacement survey to be outside acceptable limits of normal draught survey measurement error.
measurement errors which could effect the quantity of cargo recorded by survey as being loaded or discharged. The final report should include details of any defect or circumstance regarding weather, surface water, tides/ currents or on board conditions which the surveyor considers might well influence the result adversely.
Cumulative errors
Errors can occur when reading and correcting the draughts. The final fully corrected 3/4 mean draught should be within +/- 10 mm of the true mean draught. Errors of calculation. The main error to be avoided in this section is that of incorrectly positioning the LCF relative to LBP/2 the amidship point. Error of the water density in which the vessel is floating. Always ensure an average sample, or alternatively the average of a number of water samples are obtained and the correct type of certificated hydrometer is used to obtain the density. Sounding of tanks. Leaving aside documented tables which may not be accurate, the way of avoiding the main errors in this section of the survey is by ensuring, as best possible, that all volumes of liquids, especially ballast water, on board are both correctly quantified and attributed with correct densities. These factors, particularly when applied to ballast water, undoubtedly contribute to the largest number and degree of errors likely to be encountered in draught surveying. Bearing these reservations in mind, a well conducted draught survey under reasonable prevailing conditions is capable of achieving an absolute accuracy of +/- 0.5%
Expert opinion
Surveys must be carried out to the very best of the surveyors ability, with each part of the survey conducted as accurately as possible in order to minimize procedural and/or
Worked example
From the following information calculate the corrections to perpendiculars and the draughts at the perpendiculars. Also calculate the true trim. Vessel LBP 181.8 metres port side Forward draughts; Midships draughts Aft draughts Forward mean Midships mean Aft mean 4.61m 4.93m 5.58m = (4.61 + 4.65) / 2 = (4.93 + 5.10) / 2 = (5.58 + 5.6) / 2 Density at the time of draught reading 1.0185 t/m3 stbd side 4.65m 5.10m 5.60m = 4.63m = 5.015m = 5.59m = 0.96m = 171.56m = 0.96 x -2.94 171.56 = 0.96 x -1.44 171.56 = 0.96 x 7.3 171.56 = +0.0408m = -0.0081m = -0.0165m distance marks from perp. Fd = 2.94 m aft Md = 1.44 m aft Ad = 7.30 m forward
So apparent trim is: 5.59 - 4.63 And LBM is: 181.8 - 2.94 - 7.30 Forward corrn = Apparent trim x Fd LBM Midships corrn = Apparent trim x Md LBM Aft corrn = Apparent trim x Ad LBM
Now: Forward draught is Midships draught is Aft draught is True trim is mean draught
= = = =
= 101.73 cm = 5.0357 m
From the original survey the following data was given in the vessels hydrostatic particulars: Scale density of hydrostatic particulars 1.025 t/m3 Draught 5.00 5.10 Displacement 19743 20167 Tpc 42.32 42.37 Lcf -4.354 -4.289 Draught 5.50 5.60 Mctc 445.5 446.6 Draught 4.50 4.60 Mctc 434.9 435.9
The stability book stated that a negative (-) sign for Lcf indicated forward of midships. Interpolating the data from the table (it is easier to use centimetres in the interpolation rather than metres) The difference in the tabulated draughts is 10 cm and the draught we are looking for is 3.57 cm more than 5 metres Therefore: Displacement for 5.0357 m draught = 19743 + (20167-19743) x 3.57 10 Tpc for 5.0357m draught Lcf for 5.0357m draught Mctc for 5.0357 +50cms Mctc for 5.0357 50cms = = = = 42.32 + (42.37-42.32) x 3.57 10 - 4.354 + (4.354-4.289) x 3.57 10 445.5 + (446.6-445.5) x 3.57 10 434.9 + (435.9-434.9) x 3.57 10 = 435.26 = 445.89 = - 4.331 (ford of mid) = 19894.37 = 42.338
Therefore
(dm~dz) = = =
10.63 101.73 x 4.331 x 42.338 181.8 1.01732 x 50 x 10.63 181.8 = - 102.61tonnes = +3.03 tonnes
Then vessels displacement at a density of 1.025 t/m3 is calculated as follows Displacement for 5.0357m First trim correction Second trim correction = 19894.37 tonnes = -102.61 tonnes = +3.03 tonnes
This is the weight of the ship at the draught if it was in salt water of density 1.025 t/m3, which is the density of the ships hydrostatic scale. However it is floating in water of apparent density 1.0185 t/m3. So true displacement = 19794.79 x 1.0185 1.025 = 19669.26 tonnes
The weight of an empty ship consists of three elements 1. Empty ship 2. Stores 3. Ballast oil and fresh water FIXED ITEM CONSIDERED FIXED CHANGEABLE
Empty net weight = Empty ship + Stores The weight of a loaded ship consists of four elements 1. Empty ship 2. Stores 3. Ballast oil and fresh water 4. Cargo FIXED ITEM CONSIDERED FIXED CHANGEABLE FIXED ITEM
Loaded net weight = Empty ship + Stores + Cargo Therefore the cargo weight is the difference in the net weights.
Archimedes Principle
Archimedes Principle states that, when a body is wholly or partially immersed in a fluid, it appears to suffer a loss in mass equal to the mass of fluid it displaces. Mass is the amount of matter that a body contains and is expressed in kilograms and tonnes. However, for the purposes of draught surveying, weight can be assumed to be the same as mass. If a solid block of volume 1 m3 and weight 4,000 kg is immersed in fresh water it will appear to suffer a loss in weight of 1,000 kg. This can be verified by suspending it from a spring balance, which would indicate a weight of 3,000 kg. There is, therefore, a supporting force acting upwards that, in this case, is 1,000 kg. This is the buoyancy force. The volume of water displaced by the block is obviously 1 m3, as this is the volume of the block, and 1 m3 of fresh water has a weight of 1,000 kg, and that is the buoyancy force. Therefore the buoyancy force is equal to the weight of water displaced. Weight 500 kg zero kg
Buoyancy force 500 kg displaced is still the same at 1 m3. However the weight acting downwards is now only 500 kg and, once released, the block will rise until the buoyancy force acting upwards is equal to the weight acting downwards. This will be when the block is in equilibrium at a point when the underwater volume is equal to 0.5 m3, which is half the depth of the block, and the point at which the weight of water displaced is equal to 500 kg. A spring balance will now indicate zero weight. In the above explanation of Archimedes Principle, the block was immersed in fresh water. However, had it been salt water the volume of the underwater part of the block would have been less as the density of salt water is greater than that of fresh water, meaning for equal volumes the salt water is heavier, and thus a lesser volume of it would need to have been displaced for the block to float. From the above it can be seen that the weight of a ship can be calculated from its underwater volume and the density of the liquid in which it is floating. In order to calculate this volume it is necessary to know how deep the ship is floating in the water as the deeper the draught, as it is called, the greater the weight of the ship. Also the density of the water that the ship is floating in needs to be measured at the same time as the draughts are read.
Weight 4,000 kg
The same solid block hollowed out, until its weight is reduced to 500 kg, and then immersed in the same fresh ater will now float. This is because it still has the same volume of 1 m3 but its weight is now only 500 kg. If the block is completely immersed, the buoyancy force will still be 1,000 kg as before, because the volume of water
Density
Density is mass per unit volume at a given temperature. As already stated weight can be considered the same as mass as far as draught surveying is concerned. Therefore the weight of the block above is its underwater volume multiplied by the density of the liquid in which it is floating.
Metric marks
The photo shows some draught marks in the metric system. The picture shows depths from 8.49 metres to 9.64 metres. The water level is at 8.49 metres as half the width of the top of the 4 is visible above the water level (the number is made from 2 cm wide steel plate). Some numbers are easier to assess than others. For example, in the diagram each pair of lines is 2 cm apart and it can be seen that the assessment of the depth is easy when the water level is across the 8. The 6 and the 9M in the picture would also have the same easy to read features. Some small coasters are often only marked at the midships point with a designated line (again 2cm wide) called the deck line. The upper edge of this is at a known distance from the keel (K) which is the summation of the vessels official summer freeboard and summer draught. Draughts are then calculated by measuring the actual freeboard (distance of the upper edge of the deck line from the water level) with a measuring tape and deducting it from the K.
Weight in vacuum
The density of a substance can be determined by weighing a unit volume, which in the case of the metric system is a cubic metre. If a quantity of liquid for example, fresh water or sea water is weighed on a balance or on a weighbridge against the equivalent of brass weights then the atmosphere will exercise an upward thrust upon the water much greater than the upward thrust exercised on the smaller volume of brass weights. This air buoyancy effect is in fact the same as the buoyancy force for a body immersed in a fluid, as explained in the Archimedes Principle. However, this time the fluid is air, which has a density of 0.00125 t/m3 (the density of dry sea air at sea level is about 1/800th of the density of fresh water, ie 1.25 kg/m3). If the weight of the unit volume is corrected for this air buoyancy effect, the result is weight in vacuum which is equivalent to mass. For all practical purposes it is accepted that the density of fresh water is 1000 kg/m3 and that of sea water 1025 kg/m3.
Apparent density
It is commercial practice to make no allowance for air buoyancy so that commercial weights are normally weights in air. Weight in air per unit volume is known as apparent density and this should be the criteria used for all draught surveys as, after all, the ship is in air not in a vacuum. The Zeal Draught Survey Hydrometer reads apparent density in air kg/Lt @150 C and is an industry standard accepted worldwide.
Displacement ( )
Displacement is the weight of the ship. It is the underwater volume multiplied by a density. In the majority of cases the standard density used is 1.025 although there are many other in use such as 1.027, 1.000, 1.02522 etc. In order to obtain the volume the displacement is divided by whichever density has been used to compile the data.
Tpc
Represents tonnes per centimetre of immersion. It is the weight that must be loaded or discharged in order to change the ships mean draught by one centimetre.
Lcf
Represents longitudinal centre of flotation. It is the position about which the ship will trim when weights are loaded or discharged. It is the geometric centre of the water-plane, and will move as the shape of the water-plane changes when weights are loaded or discharged. The water-plane is the area of the ships hull that would be visible if the ship was cut off at the waterline.
Mctc
This stands for moment to change trim 1 centimetre. It is the moment required to change the trim of the vessel by one centimetre (a moment is weight x distance). Mctc is used in the second trim correction. Other necessary data provided within the stability book are the following:
Light ship
The weight of the ship complete in all respects when empty, but with full equipment, engine spares, water in the boiler and lubricating oil in the engine.
distances of the midships or aft draught marks from the relevant perpendicular (the midships perpendicular is located at LBP/2). Each of these corrections is applied according to the following rule: If the direction of the displacement of the draught marks from the relevant perpendicular is the same as the direction of the trim, then the correction applied to the observed draught is negative, otherwise it is positive.
Deadweight
The weight a ship can carry. Deadweight includes any fuel, water, ballast, passengers, crew and stores. It is the difference between light ship and displacement at any draught. Cargo carrying capacity, therefore, depends on the amount of fuel water and ballast remaining on completion of loading, and any additions which will be required by the ship on passage to its final port of discharge.
LBP
Represents length between perpendiculars. A ship is built to plans and the plans are drawn around two perpendicular lines that represent the forward (FP) and aft (AP) extremities of the section of the ship from which the volume is calculated. The remaining two sections of the ship, the small part of the bow and stern sections, called the appendages, are added in afterward. The forward perpendicular is considered to be where the load water line (summer load line) cuts the line of the foreside of the bow. The aft perpendicular is where it cuts the aft edge of the rudder post, or in the case of most modern vessels where no rudder post is fitted, the centre line of the rudder stock.
W
Aft draught
L
Forward draught
Perpendicular corrections
As mentioned above, ships volumes are calculated around the section of the vessel that lies between the forward and aft perpendiculars (FP and AP). When a ship is built the draught marks are located at convenient positions on the hull and these will not always be at the perpendiculars. For calculation purposes, the draughts at the perpendiculars are required and this is done with the use of similar triangles. The actual trim of the vessel, in relation to the length of the vessel between the draught marks, is one of a pair of similar triangles. The other is the correction in relation to the distance the draught marks are displaced from the relevant perpendicular. Therefore these two triangles can be used to correct the draught mark readings to what they would be at the perpendiculars. For example: Forward Corrn = Apparent Trim x Fd LBM Where: Apparent trim = trim at the draught marks. Fd = distance of forward draught marks from Perpendicular LBM = length between draught marks The calculation of the aft and, sometimes, a midships correction uses the same formula but substitutes the
e.g. If a box-shaped barges draught readings produce an arithmetical mean of the forward and aft draughts that is more than the middle draught then this indicates that the barge is hogged. Utilising the maths of the parabola, the lost section of volume (yellow area in the diagram) is 2/3 of the box that encloses it. To calculate the effect of this the following formula would be used: Mean adjusted draught = (4 x Middle) + Forward + Aft 6
(4/6 of the middle draught is 2/3 or 66.67%)
The resulting draught calculated is the mean draught adjusted to compensate for the deflection in the barge structure. This is known as the two-thirds mean correction, and was derived directly from Simpsons First Rule for finding an area under a curve. This is fine for a box shape, but ships are very rarely box shaped. Calculations have shown that the most likely amount of correction required for hog or sag on a conventionally shaped ship is threequarters or 75 %. The formula for this is called the 3/4 mean draught and is as follows: 3/4 mean draught = (6 x Middle) + Forward + Aft) 8
(6/8 of the middle draught is 3/4 or 75%)
This is the draught used to enter the ships hydrostatic tables and obtain the displacement of the ship. However, the displacement scale in the ships stability book is calculated for the ship on an even keel and in an upright condition; that is without any trim or list. Ships rarely appear in that state, although it has been known. Therefore, two corrections are now required to give the true displacement.
The above corrections are in metres and can be applied to the 3/4 mean draughts to give the true mean draught. However, the normal method used is to calculate the correction in tonnes. The displacement is taken out of the tables for the 3/4 mean draught and the layer correction applied as a negative or positive correction in tonnes by using the Tpc at that draught (Tpc is the number of tonnes required to sink the ship one centimetre). This is the first trim correction, and is calculated using the following formula: First trim correction = Trim (in centimetres) x Lcf x Tpc LBP
Lcf when loaded Where Lcf is measured in metres from amidships, The position of Lcf is crucial to the calculation of the draught survey. The true mean draught is the draught at the Lcf and not the draught amidships; unless, of course, Lcf is positioned at amidships. Consider the following diagrams. AP L Lcf
True mean draught Amidships draught
The correction is applied according to the following rule: If the Lcf and trim are in the same direction the correction is positive and alternatively when they are in opposite directions the correction is negative.
Position of Lcf
FP W The understanding of how Lcf moves is crucial. In the above formula it is measured from amidships and it is absolutely essential that it is understood which side of amidships it is. There have been more incorrect draught survey results obtained due to getting this detail wrong than anything else. The position of Lcf, in the hydrostatic particulars, is indicated by three main methods. These are: 1.Either with a minus (-) sign or a plus (+) sign, indicating a direction from amidships (see below). 2.Or labelled with the letters a or f (sometimes aft or ford) indicating aft or forward of amidships. 3.Or as a distance from the aft perpendicular (in which case the distance and direction from amidships can be easily calculated by use of the LBP/2).
Trim
LB In the above diagram the ship is on an even keel and the draught at the Lcf is the same as the draught at amidships. However, if a weight within the ship is moved further aft, the ship will trim about the Lcf so that she is deeper aft and not so deep forward; as in the next diagram. The displacement will not have changed, as the trim is achieved by moving a weight already on board and the draught at the Lcf remains the same.
Distance of Lcf from amidships LBP W Lcf Mean of forward and aft draughts Layer correction Amidships draught FP
The latter is the clearest method. The use of (-) and (+) signs can be very confusing depending on what the compiler of the tables meant by their use. In Russian and in Korean shipyards (-) means aft of amidships but they also refer to aft trim as (-). The European convention is to use (+) to mean aft of amidships and aft trim. The main reason for errors in applying the Lcf in the first trim correction are an obsession with the (+) or (-) signs as being mathematical. They are in fact only an indicator of which side of amidships Lcf is located and that depends on the shipbuilders logic. Usually the convention used is indicated at the beginning of the tables or somewhere on the pages listing the data. Lcf is the centre of the of the vessels waterplane area and as such is a function of the shape of the vessel on the waterline at any given draught and nothing else. Because the water plane changes shape to get rounder at the aft part, as the ship gets deeper, the Lcf moves aft as displacement increases and forward as displacement decreases but does not necessarily move through amidships.
In the above diagram the change to the forward draught is greater than the change to the aft draught because the ship is trimming about the Lcf and the draught at the Lcf is greater than the draught amidships, which is the mean of the forward and aft draughts. In order to obtain the true mean draught (the draught at the Lcf) a correction needs to be applied to the adjusted mean draught (the 3/4 mean draught). This correction is called the layer correction and is easily calculated using similar triangles as follows. The green trim triangle is similar to the red layer triangle as both have two of their sides in the same proportion and their included angles are equal. Therefore: Layer correction = Trim x Distance of Lcf from amidships LBP In this case the true mean draught is the draught amidships plus the layer correction. Had the Lcf been forward of amidships the correction would have been negative.
This means that from light to loaded condition Lcf will move either from: Forward to less forward. Forward to aft. Aft to more aft. In the absence of reliable information as to the convention used in the hydrostatic tables, these facts should help to determine which side of amidships Lcf lies. Therefore, when displacement is increasing, if the actual number (indicating the position of Lcf from midships) is decreasing, then it is forward of amidships (it is getting closer to zero, which is when it is at amidships) and if it is increasing it is aft of amidships (it has already passed zero at amidships and is moving further aft). Note: A recent anomaly to this rule was found with a ship that was completely box shaped except for the bow area. In this rare case the movement of Lcf was dictated by the shape of the bow alone,and Lcf initially moved aft and then forward as the vessels draught increased. Under normal circumstances, when loading a ship the Lcf can be expected to be further aft at the final survey than at the initial survey. In some cases (Russian river ships in particular) the Lcf is always aft of amidships. The opposite situation will exist when discharging cargo. Normal circumstances mean that the draught is greater after loading or, conversely, less after discharge. This may not always be the case, as a ship could load a small parcel of cargo and at the same time discharge a greater amount of ballast, thus being less deep than before loading due to the extra ballast discharged. When Lcf is shown, in the vessels hydrostatics tables, as measured from the aft perpendicular, then a simple calculation will give its position in relation to amidships (see 3 above). Lcf from amidships = LBP/2 distance from aft perpendicular.
Heel correction
In situations where a substantial heel exists, a correction should be applied. The effect of heel (or list) is to increase the waterplane area and thus lift the ship out of the water. This correction is always positive. Correction (in tonnes) = 6 x (TPC1 ~ TPC2) x (Draught1 ~ Draught2)
Where 1 is port side and 2 is starboard.
Summary
Once both trim corrections, and if required the heel correction, have been applied to the displacement for the 3/4 mean draught, we then have the weight of the ship if it were in salt water of the same density as the ships tables.
Density correction
Once the displacement obtained from the 3/4mean draught and the A, B and, if required, heel corrections has been found it needs to be corrected for the density of the water in which the ship is floating. The displacement of the vessel, from the ships hydrostatic tables, is calculated at the density used to compile the tables. When divided by this density, it gives the volume of the ship. This volume is then multiplied by the density of the water the ship is floating in to obtain the true weight of the ship. Therefore: True displacement = Displacement in salt water x Density of the dock water Density used to compile the ships tables The reason for saying density of the ships tables is that some vessels are built in shipyards where 1.020 mt/m3, 1.027 mt/m3 or some other figure may be used for the hydrostatic particulars. However the norm in 99% of cases is to calculate tables at a density of 1.025 mt/m3.
Trim factors
Trim factors are derived from the position of Lcf. They are a quick way for the vessels chief mate to calculate his final trim when loading the ship. Because Lcf is not listed in the tables its position has to be calculated from the trim factors, which are tabulated as ford and aft. A formula to calculate the position of Lcf is: Lcf from aft perpendicular = aft factor x LBP ford factor + aft factor
note of any major changes that take place to the stores between the initial and final surveys. In other words it can be considered as a reliable measurement of the ships stores etc for that reasonably short period of time.
Constant
Under the heading stability book, light ship was stated to be the weight of the empty ship in operational condition. This is: The ship, its full equipment, engine room spares, water in the boilers to working level and lubricating oil in the engine. It does not include: Personnel, cargo, fuel oils, ballast water, fresh water or stores. The weights of ballast water, fresh water and fuel are calculated and are known collectively as the deductibles or total variables. Once this total weight is subtracted from the true displacement, a net weight is left that is either the ship and stores, or the ship, stores and cargo depending on whether it is an empty or loaded ship survey. This stores quantity the difference between the light ship weight and the empty ship survey is often referred to as the constant. Constant is a misnomer and it should really be referred to as a stores variable. A ships constant may be affected by a variety of changes, such as under or over stated fuel figures, slops, mud in ballast tanks, incorrect ballast calibration tables, crew and stores changes, etc. and it should not be considered a fixed amount. Also a vessels light ship weight can change over the years due to a variety of additions and removals from the structure. These could be due to a variety of factors such as rebuilding, repairs, additions and modifications. As a consequence the vessels constant will include these changes unless a new light ship survey is carried out after each instance. From experience, this usually only happens after a rebuild or major additions. The reason for a survey when the vessel is empty is to determine this variable quantity (constant). The vessels previous experience of this constant may be the result of unreliable and badly carried out surveys. Many surveys include the lube oil in the constant and others do not. The constant can also be affected by understated fuel figures from the chief engineer, who may be keeping a quantity of oil up his sleeve for a rainy day! However, within reason this stores variable quantity (constant) can be considered to remain fixed for the duration of the ships stay in port. This is assuming that the surveyor takes
Topside tanks
Cargo hold
Cargo hold
total of any bunkers received between the arrival and departure surveys. Care should be taken that the final quantity is not arrived at by sounding the storage tanks only the original agreed figure, minus consumption and plus any deliveries should be used. In this way, only the changes between initial and final surveys will be calculated. Any slops that have been discharged ashore will also need to be allowed for. A check should be made on the quantity of slops on board and, in particular, if it is the ships intention to discharge any ashore.
Calculating volumes
Once the soundings are obtained for all of the ballast tanks and, if necessary, the fresh water tanks, the volume of water in each tank is extracted from the vessels tank calibration tables. As with the hydrostatic tables, these also come in a variety of forms. They can be either numerical or in graphic form and can sometimes be difficult to interpret. If the ship has no trim or heel, i.e. on an even keel and upright, then the depth of water at the sounding pipe will be the same throughout the tank. However when any trim or heel is present, which is the usual case, either the volumes or the soundings will need to be corrected as the water will be deeper in the direction of the trim or heel. The type of table can sometimes affect the accuracy of the value extracted. Some tables have built-in trim corrections, which give the volumes for each metre, or half metre, of trim and maybe even for every centimetre of sounding. Others have a separate table of corrections to be applied to the soundings, while some ships tables have no trim correction at all. Heel corrections, if provided, are usually in a separate table that give either a correction to the sounding or to the volume. Sounding tables with volumes for each metre of trim will give reliable quantities, although problems compared to the trim on completion at the load port in relation to that on arrival at the disport can arise (see small trimmed ballast volumes below). Tables with corrections to the soundings will give reliable quantities as long as there is sufficient sounding to which the correction can be applied (see small trimmed ballast volumes below). Tables without trim corrections require the vessel, at the time of the survey, to be as close to even keel as possible, otherwise the volumes will be in error. The resultant error can be partially compensated for by calculating a correction to the sounding using the following formula: Approximate correction to sounding = trim x tank length 2 x LBP Some small coasters do not have ballast tables. Therefore when the tanks have been pumped out, but not totally empty of liquids, and only small soundings are found, the volume of any wedge shaped residues can be calculated using the following formula. Volume of wedge = Length of tank x breadth of tank x sounding2 2 x vessels trim The use of this formula must also be regarded as an approximation as it depends on the tank being of, or close to, rectangular in shape. The residual quantities must be a wedge and not just deeper at the back of the tank.
Fresh water
Fresh water tanks are either sounded as for other tanks, or they are often fitted with water gauges graduated directly in m3 which are tonnes, as the density of fresh water can be assumed to be 1.000. These gauges take the form of transparent plastic tubes fitted to the outside of the tank with the open ends connected to the waterinside. The water finds its own level in the tube. Care has to be taken with the quantities, as most ships now use fresh water for toilet flushing and therefore a lot of the water that has apparently been used, during the vessels stay in port, may have been placed in a sewage holding tank. So a change in the fresh water of say 20 tonnes over a couple of days may only be 5 tonnes that have left the ship. Therefore the change to the fresh water is only 5 tonnes not 20.
Volume is a wedge if the length of the tank is greater than: Sounding x LBP Trim
If the tanks have overflowed then samples are easily obtained. Alternatively, it is sometimes possible to use a small handoperated siphon device or a hand pump manufactured for caravan users. Also in modern use is a device called a salinity refractometer that measures density by assessing the refraction of a small sample of water the greater the refraction the more dense the water. Only a few drops of water are required, and this can be obtained from the sounding tape bob when the tank is checked. These devices are in common use in the food industry and are proving useful for surveyors when the overflowing of tanks is not possible (see addendum 4). Whatever method is chosen, it is important that the density of the ballast water is known. This is especially so on large Cape size vessels where individual tanks can contain 5000m3 of water. i.e. 5000 tonnes of fresh water or 5125 tonnes of salt water if the density were to be 1.025 mt/m3.
Sounding problems
Sounding pipes are usually located at the after end of tanks because the normal trim for a ship is by the stern. There are some small coasters in service that are not fitted with sounding pipes but have remote-reading dial gauges in the engine room. Unfortunately, while these are adequate to inform the crew if the tanks are full or empty, they are not sufficiently accurate for draught surveying purposes. This fact should be highlighted on any survey report stating that only an estimation of the ballast remains was possible. The report should state that the survey may not be reliable because of this fact. Double-bottom ballast tanks cannot be pumped absolutely dry due to the nature of their construction and the location of the suction pipe, which must be a physical distance above the bottom of the tank to allow water to flow into it. This distance is dictated by the capacity of the ballast pump and the cross sectional area of the suction line and this then relates to the quantity of water remaining in the tank (unpumpable residue). It is often preferable to overflow full ballast tanks to prove they are completely full, although there is a school of thought that says soundings are a better option. Overflowing of double bottom tanks is the best method as long as it is permissible; they are in the bottom of the ship and the air pipe is on the weather deck. Clearly, when water is overflowing from these tanks, they will be full. Topside tanks, however, are prone to air pockets when overflowing. This depends on the trim, the height of the air pipes and the length of the tank. Relationship between tank length, air pipe height and trim
Wedge of air Topside tank 1
Topside tank 2 X
If the actual height of the air pipe is less than x then the tank may not be full. In the above diagram No 1 topside tank is not completely full while No 2 topside is. This is due to the relationship between tank length and trim (the double bottom will be full as long as the water in the sounding pipe is more than the distance x above the top of the tank). There are occasions when a ballast tank cannot be sounded. This is usually due to damage or a blockage in a sounding pipe. In these situations, the options are to leave the tank as it is throughout the survey; either empty or full. In the latter case it may be possible to overflow it to prove it full at both initial and final surveys. This is the better option, as there is a definite answer to the quantity of ballast water contained in the tank. It is usually necessary to do this to a pair of tanks, as one side being full while the other is empty causes an unacceptable list. Taking soundings when the ship is trimmed by the bow can lead to large errors as shown below. This is an explanation of why a ship, with a trim of 4.5 metres and a tank sounding of 6 cms, which was equal to 1 m3, then became 16.7 m3 when the trim was -0.60 metres by the bow (figures taken from an actual table).
Situation (1) Trim 4.5 metres by the stern Sounding 6 cms Quantity from tables 1.0 m3
Sounding pipe
Tank
Situation (2) Trim -0. 60 metres by the bow Sounding now zero (0.0m) but water just missing the sounding pipe Quantity according to the tables is 16.7 m3
Sounding pipe
Tank
Situation (3) But look at this case Trim still 0.60 metres by the bow Sounding still zero (0.0m) but now water level same as situation (1) So actual quantity in the tank is only 1.0 m3 even though the tables say it is 16.7 m3
Sounding pipe
Tank
This is why it is very bad practice to take soundings when a ship is trimmed by the bow.
(e.g. if, say, 5000 tonnes are to be loaded in No. 3 hold, then try to persuade the vessel to discharge only the ballast at that hold and keep all other tanks the same). The level of the water in the ballast tanks will, in some ways, determine the level of accuracy of the survey. Slack tanks that are sounded can sometimes result in poor measurement of the quantity inside them. The effect of even a slight movement of the ship, due to wind or waves, is to cause the water in the sounding pipe to move up and down. If the sounding rod is allowed to rest on the bottom of the tank, even briefly, this will give rise to false soundings if great care is not taken. What can be done to improve the accuracy of ballast soundings? One method is to overflow all double-bottom ballast tanks, when full, take soundings of the topside tanks and not to have any slack tanks or, if it is necessary say for trim, as few slack tanks as possible. In order to obtain accurate soundings of any slack tanks, several readings should be taken, not allowing the sounding rod to rest on the bottom; just touch and remove immediately. In this way different readings will be found and an average of them will produce a better result.
Below is a diagram of a double-bottom structure, which should help the understanding of the problems.
ADDENDUM 1 Manometer
In some circumstances the wave and swell activity can be such that it may be too rough to use a boat or the wave damping tube may be difficult or even impossible to position on the hull. This situation can often be resolved by the use of a manometer to measure the list across the deck at midships, which is then added to, or subtracted from, the inboard draught reading to obtain the outboard draught. It is not necessary for the manometer to be fitted with a scale at the ends as the height of the water in the tube is measured from the deck on each side using a tape measure. In circumstances where the list is large the end of the manometer on the low side must be positioned higher than the end on the high side to avoid the water in the tube running out. However when a scale is fitted and used for the reading care must be taken that the scale is fixed at the same height on each side. A simple manometer is constructed from a length of plastic tubing about 35 to 40 metres long of 10mm outside diameter, 6mm inside diameter, filled with water. On each end is a valve connected to a short section of 19mm tube. The valves are to allow the water in the tube to be retained without any air
Manometer
bubbles in it when the device is not in use. This is important, as any entrapped air will prevent the manometer working properly. The short sections of 19mm tube are to provide a damping action to the movement of water in the system that is caused by ship movement. From the above diagram the starboard draught is equal to the port draught plus the difference in port and starboard draughts from the manometer. In the event that the manometer is not long enough to reach the vessels sides the true difference can be calculated from the measured difference by the use of similar triangles. In this case the manometer is set to obtain readings at a known distance apart across the vessel.
Manometer Difference in port/stbd draughts
Therefore:
Difference in port/stbd draughts = Breadth x Difference in readings
Differences
The displacement and apparent weight of a vessel have a relationship, as do the relative and apparent densities of the water in which the vessel is floating. The difference between the relative density (specific gravity) as determined by the load line hydrometer and the draught survey hydrometer, is known as the air buoyancy correction, and can be accepted, at standard temperatures 15C/15C or 60F/ 60F, as 0.002 for marine surveys. The density of gases depends upon temperature, pressure and moisture content. The density of dry air at sea level is about 1/800 th. of the density of fresh water. i.e. 1.25kg/m3 when under similar conditions of temperature and pressure. It should also be noted that the actual maximum density of fresh water is 999.972 kg/m3 which occurs at a temperature of +40 C. The density of fresh water at 1000 C is 958.4 kg/m3. The correction to be deducted from the relative density of load line hydrometer to compare with an actual density of draught survey hydrometer. Example: for a sample of seawater checked by a load line hydrometer reading relative density 1.025, a draught survey hydrometer would read an actual density of 1.023 kg/l in air. All hydrometers should be calibrated regularly.
Surveyors should only use a hydrometer manufactured for the relevant type of survey being undertaken.
For further information please contact: Loss Prevention Department, Thomas Miller P&I Ltd Tel: +44 20 7204 2307. Fax +44 20 7283 6517. Email: [email protected]