Professional Documents
Culture Documents
Skoda Octavia Workshop Manual
Skoda Octavia Workshop Manual
The Workshop Manual is intended only for use within the KODA Organisation; it is not permitted to pass it on to third parties. 1996 KODA, automobilov a.s.
Service
Edition: 03.01
Supplement
Subject
Basic Edition of Workshop Manual Climatronic - Air Conditioning with Automatic Control High-pressure Sender for Air Conditioning -G65Modifications for Model Year 00 Modifications for Model Year 01
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Printed in CR S00.5102.54.20
OCTAVIA
80 Heating System
Contents
Service
Page
Removing and installing heater unit ......................................................................................... - Removing and installing heat exchanger of heating system ....................................................
Servicing heating system ........................................................................................................... - Dash panel vents and air ducts ................................................................................................ - Removing and installing right dash panel vent ...................................................................... - Removing and installing centre and left dash panel vents .................................................. - Inspecting ventilation frame ...................................................................................................... - Removing and installing air duct to defroster vents ................................................................. - Heating system, heater controls and air ducts ......................................................................... - Removing and installing heater controls .................................................................................. - Detaching and attaching Bowden cables of heater controls .................................................... - Connection diagram for Bowden cables at heater controls ...................................................... - Connection diagram for Bowden cables at heater ................................................................... - Detaching, attaching and adjusting Bowden cables at heater .................................................. - Replacing bulb of heater controls ............................................................................................. - Removing and installing fresh air blower -V2 ........................................................................... - Removing and installing series resistor for fresh air blower -N24 ............................................ - Removing and installing positioning motor for fresh air and recirculated air flap -V154 .......... - Testing operation of positioning motor for fresh air and recirculated air flap -V154 and of switch -E159 ......................................................................................................................... - Removing and installing footwell vents .................................................................................... - Removing and installing dust and pollen filter .......................................................................... - Removing and installing coolant shutoff valve ......................................................................... - Two-way valve for coolant shutoff valve -N147 ........................................................................
80-1 80-1 80-3 80-3 80-3 80-4 80-5 80-7 80-7 80-8 80-8 80-8 80-10 80-11 80-11 80-12
87
Air Conditioning
Safety precautions when working on models with air conditioning and when handling refrigerant R 134a ........................................................................................................................
Page
87-4 87-4 87-5 87-7 87-9 87-10 87-11 87-12 87-14 87-15 87-16 87-16 87-18 87-20 87-1
Description of air conditioning, test and service work ........................................................... - Operating principle of air conditioning system .......................................................................... - Design of refrigerant circuit ...................................................................................................... - Parts of refrigerant circuit ......................................................................................................... - Connections for quick-coupling adapters at refrigerant circuit ................................................. - Parts for safeguarding refrigerant circuit .................................................................................. - Switches for refrigerant circuit .................................................................................................. - Properties of refrigerant R 134a ............................................................................................... - Properties of refrigerant oil ....................................................................................................... - Important information regarding work on refrigerant circuit ..................................................... - Detecting leaks at refrigerant circuit with leak detector ............................................................ - Service stations for draining, evacuating, filling and measuring pressure of refrigerant circuit ........................................................................................................................................ - Cleaning refrigerant circuit with compressed air and nitrogen ................................................. - Capacities ................................................................................................................................. Continued next page
------------ I ------------
Service
Servicing air conditioning and heating - engine compartment (manual control) ................. .................................................................................... ............................................................................ ................................................... .................................................. ................................................................................ ................................................. ............................................................................. ...................................................................... ......................................................... ....................................................................................... ............................................................................................. ......................................................................................... Servicing magnetic clutch -N25- (manual control and Climatronic) ...................................... Servicing air conditioning and heating - passenger compartment (manual control) ..........
Removing and installing air conditioner (manual control) ..................................................... ...................................................... Disassembling and assembling evaporator housing (manual control) .................................
Climatronic (air conditioning with automatic control) - self-diagnosis ................................. .................................................................................................................................... ............................................................................................... ........................................................................................ . 1552 ............. ......................................................................................................... ....................................................................................................... ................................................................................................................................. .............................................................................................................. ............................................................................................................................. ............................................................................................................... ........................................................................................................................... ................................................................................................................... ................................................................................................
Climatronic - air conditioning with automatic control ............................................................. ......................................................... ..................................................................................... ................................................................................................................................ ......................................................... .................................................................................... ............................................................................................. ......................................................................... ................................................................ ...........................................................................................
------------ II ------------
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
OCTAVIA
87-21 4 87-36 87-32 1 87-38 87-44 87-42 87-47 87-70
Edition 03.01 S00.5102.54.20
OCTAVIA
Heating System
80
Note: The air in the passenger compartment flows out of the car through 2 ventilation frames (in the right of the luggage compartment in the area of the bumper) page 80-3.
1 - Dash panel With integrated air guide ducts for defroster nozzles and dash panel vents.
Removing and installing General Body Repairs; repair group 70 2 - Side window defroster nozzle Clipped in place 3 - Right dash panel vent Removing and installing page 80-3.
80
Heating System
OCTAVIA
5 - Trim panel for dash panel inserts Removing and installing General Body Repairs; repair group 70
6 - Left and centre left dash panel vents Removing and installing page 80-3.
------------
------------
4 - Centre right dash panel vent Removing and installing page 80-3.
7 - Windscreen defroster nozzle 8 - Air guide duct to dash panel vents Bolted to heating system, with catch at top. 9 - Air guide duct to defroster nozzles Removing and installing page 80-4.
OCTAVIA
Heating System
80
Note: Only the left and centre left dash panel vents are identical.
Note:
This illustration shows the ventilation frames with the rear bumper installed. 2 ventilation frames (on right side only) are installed for forced ventilation. The air guides formed by the trim panel of the luggage compartment must not be covered over if ventilation of the passenger compartment is to operate properly.
------------
------------
80
Heating System
OCTAVIA
------------
------------
OCTAVIA
Heating System
80
Note: The fresh air is drawn in through a dust and pollen filter; removing and installing page 80-16.
1 - Heater controls Removing and installing page 80-7. Detaching and attaching bowden cables page 80-7. Adjusting bowden cables page 80-8.
Edition 08.96 S00.5102.50.20
Connection diagram for bowden cables page 80-8. Replacing bulb page 80-10.
Note: At the start of production, a bulb is used for illuminating the rotary switches. Production will be converted to LEDs at a subsequent date; these will then no longer be replaceable.
------------
------------
80
Heating System
OCTAVIA
Notes:
No recirculated air operation is possible in the defrost mode (the recirculated air mode is switched off about 15 before the air distribution rotary switch reaches the end position air supply to windscreen.
------------
------------
2 - Switch for fresh and recirculated air flap -E159 Testing operation page 80-13
3 - Driver side footwell vent 4 - Rear duct 5 - Connection piece to rear duct 6 - Left cover for footwell vent 7 - Footwell vent Removing and installing page 80-15.
OCTAVIA
8 - Heater unit Removing and installing page 8017 Detaching, attaching and adjusting Bowden cables page 80-8 Connection diagram for Bowden cables page 80-8 9 - Heat exchanger Removing and installing page 8019 On vehicles with mapped cooling, in all-metal version because of higher temperatures
Heating System 10 - Air guide duct to defroster vents Removing and installing page 804 11 - Fresh air/recirculated air flap motor -V154 Testing operation page 80-13 Removing and installing page 8012 12 - Series resistor for fresh air blower -N24 Removing and installing page 8011 13 - Fresh air blower -V2 Removing and installing page 8011
80
Notes: Inspect Bowden cables before installing; replace any cables which are stiff or damaged. Attach wire cable -B- the right way round (coil facing down).
80
Heating System
OCTAVIA
OCTAVIA
Heating System
80
Notes:
Inspect bowden cables before installing; replace any bowden cable which does not operate freely or is damaged. After installing the bowden cable, turn rotary switch to both end stops (should reach both end stops).
Attaching bowden cable to temperature flap and adjusting KTurn rotary switch for temperature flap as far as the stop in cold position. Attach bowden cable to the lever for the temperature flap -B-. Press lever for temperature flap -B- slightly in direction of arrow. Fix bowden cable sheath in place with securing clip -A-. Turn rotary switch for temperature flap to both end stops (should reach both end stops).
Attaching bowden cable to central flap and adjusting KTurn rotary switch for air distribution to the stop in position air flow to windscreen. Attach bowden cable to the lever for the central flap -C-. Press lever for central flap -C- slightly in direction of arrow. Fix bowden cable sheath in place with securing clip -A-. Turn rotary switch for air distribution to both end stops (should reach both end stops).
------------
------------
80
Heating System
OCTAVIA
Attaching bowden cable to footwell/defroster flap and adjusting Turn rotary switch for air distribution as far as the stop in position air flow to windscreen. Attach bowden cable to lever for footwell/defroster flap -B-. Press lever for footwell/defroster flap -Bslightly in direction of arrow. Fix bowden cable sheath in place with securing clip -A-. Turn rotary switch for air distribution to both end stops (should reach both end stops).
K-
OCTAVIA
Heating System
80
Separating fresh air blower -V2 and base plate KRemove screw -A-. Pull fresh air blower out of the base plate -B-.
Notes:
When installing fresh air blower in the base plate, ensure the connector -C- is correctly installed. After installing fresh air blower, ensure it is correctly located in the heater.
Removing and installing series resistor for fresh air blower -N24
KRemove screw clip for foam cover. Fold foam cover -C- to the side. Take connector -A- off the series resistor. Remove screw -B- and take off resistor mount.
80
Heating System
OCTAVIA
Removing series resistor from the resistor mount KDrill or shear off the securing screws -A-. Press back catches -C-. Remove series resistor -B-.
Note: When installing series resistor, attach with 3.2 x 10 mm self-tapping screws -D-.
Removing and installing positioning motor for fresh air and recirculated air flap -V154
Removing - Remove glove box. General Body Repairs; repair group 70 KSet fresh air and recirculated air flap to recirculated air (if possible). Unplug connector -A-. Remove bolt -B-. Push positioning motor down until the tongue -D- is clear of the slot -E- and push positioning motor to the outside -direction of arrow-.
Installing KSet fresh air and recirculated air flap manually to fresh air. Plug in connector -A-. Operate the fresh air and recirculated air switch and switch ignition on and off in order to move lever -F- on positioning motor into centre position -direction of arrow-. Tilt positioning motor down about 45 and install.
OCTAVIA
Heating System
80
Testing operation of the positioning motor for fresh air and recirculated air flap -V154 and of switch -E159
Notes:
No recirculated air operation is possible in the position air supply to windscreen (switch -E159- is blocked mechanically by the rotary switch) to ensure that misted windows are cleared as rapidly as possible. Otherwise, the windows might mist up in the recirculated air mode (the moisture in the air in the passenger compartment increases and then condensates on the windows). Testing operation of switch -E159 and of positioning motor -V154 KSwitch on ignition. Set rotary switch -A- for fresh air blower -V2 to stage 3. Turn rotary switch -B- for air distribution to the air supply to dash panel vents position. Do not operate switch -C- for fresh and recirculated air flap -E159-. The air is drawn in through the dust and pollen filter (fresh air mode, indicator lamp in switch must not come on). Operate switch -C- (recirculated air mode, indicator lamp in switch should come on). The air is drawn in from the area of the front passenger footwell (recirculated air).
K-
Indicator lamp in switch -C- should go out, the fresh air and recirculated air flap moves into fresh air position (switch -C- operated by rotary switch -B-).
------------
------------
Turn rotary switch -B- for air distribution as far as the stop in position air supply to windscreen.
80
Heating System
OCTAVIA
Notes:
If the controls operate properly and the windows nevertheless mist up: -
Inspect dust and pollen filter for dirt page 80-16. Inspect forced ventilation page 80-3.
If the controls do not operate properly, test switch -E159. Testing operation of switch -E159 - Remove glove box. General Body Repairs; repair group 70. KUnplug connector -A- from positioning motor for fresh air and recirculating air flap -V154. Switch on ignition. Turn rotary switch for air distribution into air supply to dash panel vents position. Do not operate switch -E159 (not pressed in). Fresh air mode, indicator light in switch must not come on. Connect voltage tester V.A.G 1527 B between contacts 1 and 3 at connector -A-. Indicator lamp in voltage tester should come on. Operate switch -E159 (press). Recirculating air mode, indicator light in switch should come on. Indicator light in voltage tester should go out. KConnect voltage tester between contact 2 and 3 at connector -A-. Indicator light in voltage tester should come on.
------------
------------
OCTAVIA
Heating System
80
Turn rotary switch for air distribution as far as the stop in position air supply to windscreen. Indicator light in switch and in voltage tester should go out.
Notes:
If no fault can be found during this test: -
Inspect fresh air and recirculating air flap to ensure it operates freely. Replace positioning motor -V154.
Test cable connection between -E159 and -V154 for open circuit and short circuit. Test voltage supply and earth connection to switch -E159. Replace heater controls.
K-
Remove left cover for footwell vent -E(2 expanding clips, 2-piece). Remove support -D-. Remove connection piece -C- between footwell vent and rear duct. Press footwell vent -B- down out of the catches -A- and remove in direction of arrow.
------------
------------
80
Heating System
OCTAVIA
Installing The surround should engage in the first lamellar segment of the filter element -arrow A-.
------------
------------
OCTAVIA
Heating System
K The coolant shutoff valve -arrow- is located in the engine compartment in the area of the heat exchanger flange. Remove intake hose.
K-
S870173
Q 7 6 % P 2 7 6 ( # # 4 5 4 % 3 # ' " $ 1 $ & I F H G B B D ' 0) ) C C ) 0 E ! A C& ! !% 7 6 6 3 ' 0 ) & & 2 7@ 6 # 9 8 2 7 6 ( # # 4 5 4 % 3 # ' % " $ 1 $ & )& 0 ! ! ) ) %
80 and
Release pressure in coolant circuit by opening the cap at the coolant expansion reservoir. Pinch off coolant hoses upstream and downstream of coolant shutoff valve with MP 7-602. Detach vacuum hose from coolant shutoff valve. Place collecting vessel below coolant shutoff valve and detach coolant hoses. Installation is performed in the reverse order. After installing, replenish coolant and pay attention to specification of coolant additive. Inspection and Maintenance Unplug connector at valve -arrow-. Measure resistance between the contacts of the valve. Specification: 31 ... 39 If the specification is not achieved: Replace valve.
-----------------------
80
OCTAVIA
Inspect wiring according to current flow diagram, repair if necessary. Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder If the wiring is o.k.: Models without air conditioning and models with air conditioning with manual control - Test heater controls Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder; replace if necessary page 80-7. Test Climatronic control unit page 87-51 (interrogate fault memory); replace if necessary page 87-79.
Removing KUnplug connector at valve -arrow-. Detach vacuum hoses from valve. Release valve and take out.
S870173
------------
------------
OCTAVIA
Heating System
80
K-
Notes:
Connect the coolant hoses the right way round:
Coolant hose -A- feed from cylinder head Coolant hose -B- return flow to water pump
Bleed coolant circuit. Engine, Mechanical Components; repair group 19 KPlace container below the connection for the hose -B- and carefully blow the coolant out of the heat exchanger through the connection for hose -A- (using compressed air).
Note:
------------
------------
K-
Fold up the pre-punched points -A- of the heat insulating mat and remove the hexagon nuts and washers -B- located behind (tightening torque 15 Nm).
80
Heating System
OCTAVIA
- Remove dash panel. General Body Repairs; repair group 70 Remove footwell vent page 80-15.
- Remove front passenger airbag unit. Electrical System; repair group 96 Cover over all opened connectors and air guide ducts of the heater unit to prevent any swarf in getting in. Drill off support for the dash panel with a 7 mm drill at the points marked with -A(connection points). Bend part -B- of support at the specified breaking point -C- to the side in direction of arrow.
K-
Note: After installing heater unit, bend back part -Binto its original position and bolt the shaped section marked with broken lines to the holes -A(e.g. M 6 x 10).
Separate electrical connection between car and heater unit (plug connection and boltedon earth cable at A pillar). Remove heater unit in direction of arrow.
K-
Notes re installing:
Inspect all the seals and gaskets on heater unit for signs of damage before installing and replace any damaged seals and gaskets. When inserting the heater unit, inspect the seal at the intake duct; it should be making contact with the body.
K Replace gasket -A- at heat exchanger and ensure it is correctly located at the contact surface -C-. The flow direction of the coolant is indicated on the connection of the heat exchanger (arrow -B-). All the cable straps which have to be taken off for removing the heater unit, should be fitted on again at the same point after assembly.
OCTAVIA
Heating System
80
Notes:
If the heat exchanger does not engage properly when being installed in the heating flap box, it should be attached with 2 suitable screws -C- (e.g. 3.2 x 20 mm self-tapping screws). Ensure that the gasket -D- is correctly installed; it must not be visible after installation.
K Replace gasket -A- and ensure that it is correctly installed at the contact surface -C-. The flow direction of the coolant is marked at the connection of the heat exchanger (arrow -B-).
------------
------------
OCTAVIA
Air Conditioning
87
Safety precautions when working on vehicles with air conditioning and when handling refrigerant R 134a
The components and the pipe system of the air conditioning are filled with the refrigerant R 134a (Tetrafluorethane CH2F-CF3). This refrigerant will also be familiar from the trade designations H-FCR 134a or SUVA 134a available from Dupont (other trade designations may be common in other countries). Observe the following safety precautions in respect of refrigerant R 134a (additional precautions and regulations may apply in individual countries): Should it be necessary to drain the refrigerant circuit for carrying out repairs to the vehicle, hand over the vehicle to an air conditioning service centre workshop!
Reason:
Only service centre workshops have available the suitable service stations in order to professionally extract the refrigerant. If the refrigerant circuit is opened in a service centre workshop, avoid any contact with liquid refrigerant or with refrigerant vapours. Should refrigerant flow out despite observing all the necessary safety precautions, do not inhale the gas/air mixture which is produced. For this reason, always switch on the extraction facilities available and protect your hands with rubber gloves and your eyes with eye protection.
Reason:
The intensive effect of refrigerant on unprotected parts of the body produces frostbite. Refrigerant gas is heavier than air, colourless and odourless and thus displaces the oxygen present in the air without this being perceptible.
Notes:
It is recommended to keep a bottle of eye wash for rinsing out eyes close at hand. If liquid refrigerant gets into your eyes, rinse out your eyes thoroughly with water for about 15 minutes. After this, treat your eyes with eye drops and consult a doctor immediately even if your eyes are not painful. The doctor should be advised that the frostbite has been caused by refrigerant R 134a. If refrigerant gets onto other parts of your body despite observing all the necessary safety precautions, these should also be thoroughly rinsed with cold water immediately for at least 15 minutes.
87
Air Conditioning
OCTAVIA
Work on the refrigerant circuit of the air conditioning system should only be carried out in well ventilated areas. Refrigerant must not be stored in lower-level areas (e.g. cellars) and in related exit passages or window sills.
Reason:
Refrigerant is colourless and odourless. In addition, it is heavier than air and thus displaces the oxygen. This produces the risk of suffocation in poorly ventilated areas or in assembly pits, without the persons present being able to sense the danger beforehand.
Remedy:
When working on the refrigerant circuit, ensure that there is no assembly pit, shafts or cellar entrances within a surrounding area of 5 m. Switch on the available extraction equipment. It is not permitted to carry out any welding or brazing/soldering work on parts of the filled air conditioning system. This also applies to welding and brazing/soldering work on the vehicle if there is a risk of heating parts of the air conditioning system. When carrying out repair spray-painting, the temperature of the components in the drying oven or in its preheating zone must not rise above max. 80C.
Reason:
The heating up of components produces a severe overpressure in the system which can result in the pressure relief valve opening. During electric welding, invisible ultraviolet rays are released which penetrate the refrigerant hoses and decompose the refrigerant.
Remedy:
Damaged or leaking parts of the air conditioning system must not be repaired by welding or brazing/soldering but should always be replaced. Extract the refrigerant from the refrigerant circuit beforehand using the service station (hand over vehicle to a service centre workshop). Although refrigerant is not a fire hazard, it is not permitted to smoke, or to carry out welding or brazing/soldering work in an area in which refrigerant is present.
Reason:
Because of the high temperature produced by a naked flame or by hot bodies, the refrigerant gas is chemically split. Inhaling the toxic split products which are produced results in an irritating cough and in nausia.
------------
------------
OCTAVIA
Air Conditioning
87
Containers filled with refrigerant (e.g. filling cylinder of the service station) must in no account be rapidly heated or exposed to the direct rays of the sun. On no account fill a container completely with liquid refrigerant. An adequately large expansion area (gas cushion) has to be available otherwise the container will rupture if the temperature rises, with disastrous consequences. Refrigerant must on no account be filled into systems and containers in which air is present.
Remedy:
Evacuate systems and containers before filling with refrigerant. Refrigerant must not be drained into the environment but must be extracted from the refrigerant circuit using an extraction or service station. The extracted refrigerant is then re-processed locally or returned to the manufacturer for disposal in conformity with environmental regulations (other or additional regulations may apply in individual countries). For this reason, handle the vehicle to a service centre workshop (such workshops have available the necessary facilities and tools). After emptying the air conditioning system, interrupt the voltage supply to the magnetic coupling -N25- (e.g. unplug connector from A/C pressure switch -F129-).
Reason:
Interrupting the voltage supply prevents the compressor being switched on inadvertently while the refrigerant circuit is empty.
------------
------------
87
Air Conditioning
OCTAVIA
------------
------------
OCTAVIA
Air Conditioning
87
Note:
All the components of the air conditioning system marked with a * as well as all the refrigerant hoses and refrigerant pipes can be repaired or replaced only in service centre workshops for the refrigerant first of all has to be extracted with a service station. HD = high pressure side ND = low pressure side
1 - Oil drain plug * 2 - Magnetic coupling -N25 3 - Compressor * 4 - Pressure relief valve * 5 - Condenser *
------------
------------
87
Air Conditioning
OCTAVIA
6 - Receiver with drier* 7 - Valve for extracting, filling and measuring* High-pressure side 8 - Cap 9 - Connection with valve* 10 - Air conditioning pressure switch -F129- or high-pressure sender -G65-
11 - Expansion valve* 12 - Evaporator* 13 - Cap 14 - Valve for extracting, filling and measuring* Low-pressure side 15 - Pre-volume*
OCTAVIA
Air Conditioning
87
Note: The compressor contains refrigerant oil which can be mixed with refrigerant R 134a at all temperatures.
K Condenser The condenser transfers heat from the compressed refrigerant gas to the surrounding air. The refrigerant gas condenses when this is done to form a liquid.
K Receiver The receiver gathers the liquid drops and then passes them in an uninterrupted flow to the expansion valve. Moisture which has penetrated into the refrigerant circuit during removal and installation work, is absorbed in the receiver by a drier.
87
Air Conditioning
OCTAVIA
K Expansion valve The expansion valve atomises the inflowing refrigerant and regulates the flow as a function of the different pressures so that the vapour, depending on the heat transport, does not become gaseous until it reaches the outlet of the evaporator.
K Evaporator The liquid refrigerant evaporates in the evaporator. The heat required for this is drawn from the air as it passes the evaporator ribs. The air cools down as this happens. The refrigerant evaporates and is drawn in by the compressor together with the heat which it has absorbed in the form of a gas.
Pipes and hoses of the refrigerant circuit The mixture of refrigerant oil and refrigerant R 134a attacks certain metals (e.g. copper) and alloys and dissolves certain hose materials. For this reason, use only genuine replacement parts.
OCTAVIA
Air Conditioning
87
K O-ring seals These rings provide a seal at the connection points between the individual components of the refrigerant circuit. Only O-rings which are resistant to refrigerant R 134a and the related refrigerant oils, may be used. Always use genuine replacement parts. O-ring seals: Always use only once and then replace. Pay attention to the correct diameter -a- and -b-. Moisten with refrigerant oil before inserting.
K Connection with high pressure valve 1 - Base with female thread 2 - O-ring: 10.8 mm; 1.8 mm 3 - Valve with groove for O-ring and M8x1 female thread for cap 4 - O-ring: 10.8 mm; 1.8 mm 5 - Cap
------------
------------
87
Air Conditioning
OCTAVIA
K Connection with low pressure valve 1 - Base with male thread and groove for O-ring 2 - O-ring: 7.6 mm, 1.8 mm 3 - Valve: female thread for M8x1 cap 4 - O-ring for cap: 7.6 mm; 1.8 mm 5 - Cap
Note: If the pressure relief valve has opened, determine the cause for the excess pressure in the system and rectify.
K Coil for magnetic coupling -N25 An overheating protection is installed in the magnetic coil. The overheating protection interrupts the magnetic coil as soon as the magnetic coupling is heats to an excessive extent (about 180 C) (e.g. if the compressor is stiff). A protective diode is also integrated in the magnetic coil (reduces voltage peaks which may arise when the magnetic coupling is switched off).
OCTAVIA
Air Conditioning
87
Switches the magnetic clutch -N25- off through the radiator fan control unit if coolant temperature is 119 C, and on again at a temperature of 112 C (engine overheating protection).
------------
------------
87
Air Conditioning
OCTAVIA
K Outside temperature switch -F38Switches off the magnetic coupling through the radiator fan control unit at a temperature of 2 C and switches it on again at 5 C (anti-icing protection for evaporator).
------------
Solubility of the refrigerant oil
------------
A small quantity of the special refrigerant oil (poly-alkylene-glycol-oil) required for the compressor for lubricating cylinder walls, also flows within the refrigerant circuit and mixes with the refrigerant R 134a.
OCTAVIA
Air Conditioning
87
Displacement of air by gaseous refrigerant Refrigerant gas is heavier than air and therefore spreads at floor level. It gathers in inspection pits and displaces the air which is present at such points. Environmental compatibility Refrigerant R 134a, to the extent that it reaches the Earths atmosphere, contributes to an intensification of the greenhouse effect. The greenhouse effect of refrigerant R 134a is significantly less than that of refrigerant R 12. Toxicity Refrigerant is non-toxic up to a temperature of 101 C and - provided proper attention is paid to the instructions for handling refrigerant R 134a - it does not have any detrimental effects on the human body. It is odourless, does not have any irritant effect and is thus panic-proof. Gaseous or vaporous refrigerant does not affect food and therefore does not render them toxic or unsuitable for consumption. Reaction to plastics Refrigerant acts as a solvent for certain plastics. Such dissolved plastics may be separated out when they cool in the expansion valve and thus block the valve. For this reason, always use only genuine replacement parts! Reaction to metals In its pure state, refrigerant R 134a is chemically stable and does not attack iron or aluminium. Impurities in the refrigerant, e.g. compounds of chlorine, can result, however, in certain metals and plastics being attacked. This can lead to blockages, leaks or deposits at the piston of the compressor. Critical temperature/critical pressure The refrigerant R 134a remains chemically stable up to a gas pressure of 39.5 bar (this equals a temperature of 101 C); above this temperature the refrigerant decomposes (refer to Combustibility). Water content Water is soluble in liquid refrigerant only in quite small quantities. In contrast, refrigerant vapour and water vapour mix to the same ratio. Any water present in the refrigerant circuit is transported as droplets if the drier in the receiver is saturated. Proper operation of the drier is therefore no longer assured. This water flows as far as the nozzle of the expansion valve and is transformed into ice, which in turn reduces the efficiency of the cooling system.
------------
------------
87
Air Conditioning
OCTAVIA
Water destroys the air conditioning system because acids are produced at high pressures and temperatures in combination with other impurities. Combustibility Refrigerant is non-combustible. In contrast, it has a fire-retardant or fireextinguishing effect. Refrigerant is decomposed by flames and glowing surfaces. Refrigerant is also split by UV light (as produced during electric welding). In this case, toxic split products (fluorocarbon and traces of carbonyl fluoride and fluorine) are produced, although the irritation of the mucous membranes does provide sufficient and timely warning. Filling factor A vapour space has to be present within the reservoir. The liquid expands as the temperature rises and the space filled with vapour becomes smaller. At a certain point in time there will only be liquid present in the reservoir. After this moment, only a slight rise in temperature is sufficient to produce very high pressures in the reservoir because the liquid wishes to expand further but there is no more space available for this. The forces which are produced in such a case are sufficiently large to cause the reservoir to burst. To ensure that the reservoir is not overfilled, specifications are laid down in the compressed gas recirculations in respect of how many kilograms of refrigerant may be poured in for each litre of internal volume of the reservoir. This filling factor, multiplied by the inner volume, produces the permissible filling capacity, this being 1.15 kg/ltr. in the case of refrigerant R 134a. Detection of leaks The refrigerant circuit may develop a leak, for example as a result of external damage. Detecting minor leaks is only possible using an electronic leak detector, because of the small quantity of refrigerant which flows out. Properties of the refrigerant oil An oil with special properties also circulates in the refrigerant circuit for lubricating the compressor. The principal properties are the high solubility with refrigerant, good lubrication properties, freedom from acids and absence of moisture. The poly-alkylene-glycol (PAG) oils which are suitable for the refrigerant R 134a, are highly hygroscopic (water-absorbent) and cannot be mixed with other oils. For this reason, any opened containers should be sealed again immediately to prevent moisture getting in. Refrigerant oil ages as a result of moisture and acids, becomes dark, viscous and aggressive to metals.
------------
Notes:
------------
None of the oils used for refrigerant circuits containing refrigerant R 12 may be used for refrigerant circuits filled with refrigerant R 134a Because of its chemical properties, the refrigerant oil must not be disposed of together with engine oil or gear oil. Refrigerant oil has to be disposed of separately as toxic waste.
OCTAVIA
Air Conditioning
87
------------
------------
87
Air Conditioning
OCTAVIA
O-ring seals Use only seals which are resistant to refrigerant R 134a and to the relevant refrigerant oil Use seals only once Oil with refrigerant oil (PAG oil) before installing Pay attention to the correct inner diameter
When blowing through components with compressed air nitrogen, always extract the gas mixture which flows out of the components with suitable extraction equipment (workshop extraction equipment). After completing repairwork, screw the caps onto the filler valves. The refrigerant circuit must not be purged with purging product R 11. Do not add any refrigerant to a filled refrigerant circuit (if it is unclear how much refrigerant is already in the circuit, empty system, evacuate and re-fill).
Service station for draining, evacuating, filling and for measuring pressure of refrigerant circuit
When carrying out repairs to the refrigerant circuit, it is necessary to open the circuit. Beforehand, the refrigerant has to be properly extracted, and the refrigerant circuit filled again after repairs are being completed. Special equipment is available from the trade for refrigerant R 134a for such operations, e.g. V.A.G 1770 and V.A.G 1771.
------------
------------
OCTAVIA
Air Conditioning The adapters required to connecting the service stations to the refrigerant circuit should be included with the parts supplied with the service station. All essential information regarding working with the service station is contained in the relevant operating instructions. There are service stations which clean the extracted refrigerant and use it again for filling the system. The extracted refrigerant must not be used for filling the system if a compressor damage exists (with the exception of leaks and external damage), dark, sticky deposits are found in the circuit, any doubts exist regarding the composition of the extracted refrigerant. Draining The refrigerant circuit should be drained if parts of the refrigerant circuit are to be removed, doubts exist regarding the quantity of refrigerant in the circuit, safety measures necessitate this. Evacuating Before the empty refrigerant circuit can be filled, it must be evacuated, in other words all the air eliminated. Moisture is also withdrawn from the circuit during this process. The pressure gauge of the service station must indicate an absolute pressure of 10 mbar (= 0.990bar vacuum) and hold this at a constant level for at least 1 hour after the service station is switched off. In this case, the refrigerant circuit is leaktight and can be filled. Note: If the pressure changes during this time, there is either a leakage in the refrigerant circuit or residues of moisture or refrigerant are still present in the circuit. Remedy Pour 100 g of refrigerant into the circuit and find the leak point with a leak detector and rectify. Once again evacuate the refrigerant circuit and repeat the pressure test. The refrigerant circuit must not be filled until the vacuum remains constant.
87
87
Air Conditioning
OCTAVIA
Filling system Capacity of refrigerant R 134a page 87-20, Capacities The quantity of refrigerant oil which was extracted should be filled into the system again. This instruction applies only in the case where no other components except the receiver was replaced or the refrigerant circuit was not cleaned with compressed air and nitrogen page 87-18, Cleaning refrigerant circuit with compressed air and nitrogen. Capacity page 87-20, Capacities. Test operation of the air conditioning system and test pressures in the refrigerant circuit as necessary. Measuring pressure Appropriate adapters are required for the connection of the pressure gauges to the high and low pressure sides (extraction and filling valve).
OCTAVIA
Air Conditioning
87
pressure and temperature measurements in the circuit indicate that there is likely to be moisture in the circuit, uncertainty exists regarding the quantity of refrigerant oil in the refrigerant circuit, the compressor had to be replaced because of an internal damage (e.g. noisy or no capacity).
Important! Carry out work only with pressure reducers for nitrogen cylinders. The gas mixture flowing out of the components should be extracted using suitable extraction equipment.
Blowing through refrigerant circuit with compressed air nitrogen Connect modified filler hose with appropriate adapters to workshop compressed air system and to the component to be cleaned. Switch on extraction system and extract impurities and refrigerant oil with suction hose. Continue injecting compressed air into components until no further dirt and refrigerant oil flows out (e.g. check with absorbent paper or white cloth. Connect pressure reducer to nitrogen cylinder (low pressure = 2 bar gauge) and remove moisture from individual components by injecting nitrogen through nitrogen pressure hose and the appropriate adapters (extraction system must be running). As it is not possible to provide any accurate figures regarding the quantity of refrigerant oil which remains in the compressor, all the oil should be drained from the compressor and the compressor re-filled with refrigerant oil. The quantity corresponds to that which is present in the replacement compressor page 87-20, Capacities.
Notes:
It is only possible to drain the oil from the compressor through the filler opening and the compressor therefore has to be removed. After no further refrigerant oil flows out of the compressor, rotate the compressor by hand and drain the remaining oil. The receiver should be replaced each time the refrigerant circuit is opened and should be kept closed for as long as possible in order to minimise the amount of moisture absorbed in the drier.
------------
------------
87
Air Conditioning
OCTAVIA
Capacities
Refrigerant circuit 750+50 g refrigerant R 134a
Note: When filling refrigerant circuit, always fill up to the upper tolerance limit (refrigerant remains in the filling hoses).
Refrigerant oil For Sanden or Zexel compressor: 135 15 cm3 PAG oil (Order No. G 052 154 A2). Oil distribution The oil which was in the oil pan of the compressor before the air conditioning is first switched on, is distributed in the refrigerant circuit as follows: Compressor Condenser Suction hose Pressure hose Evaporator Receiver/drier approx. 50 % approx. 10 % approx. 10 % approx. 20 % approx. 10 %
OCTAVIA
Air Conditioning
87
Notes: All the components of the air conditioning system marked with * as well as all the refrigerant hoses and refrigerant lines can only be serviced or replaced in service centre workshops as the refrigerant has to be extracted first of all with a service station. Observe safety precautions when working on models with air conditioning system and when handling refrigerant R 134a.
Edition 08.98 S00.5102.51.20
Pay attention to notes regarding work on refrigerant circuit. 1 - Extraction and filling valve* High-pressure side For extracting, filling and measuring Always fit on cap with seal
87
Air Conditioning
OCTAVIA
2 - Air conditioning pressure switch -F129- or high-pressure sender -G65 -G65- is fitted in place of -F129- on models from Model Year 99 with 1.6-ltr./74 kW engine -G65- is fitted to all models as of Model Year 2000 -F129- (4-pin plug connection), operation, removing and installing, testing page 87-24 -G65- (3-pin plug connection), operation page 87-11, removing and installing, testing page 87-25 3 - Expansion valve* Removing and installing heat insulation page 87-26
------------ 87-22 ------------
Detaching and attaching refrigerant lines page 87-26 Removing and installing page 87-26 4 - Dust and pollen filter Below plenum chamber cover Removing and installing page 80-16 5 - Ambient temperature switch -F38 Switches off magnetic clutch -N25- if ambient temperature is too low (off at 2 C for models up to Model Year 99, off at 0 C for models from Model Year 2000, on at 5 C) Clipped into place in left of plenum chamber
Edition 07.99 S00.5102.53.20
3 e U 0 U 0 Q P 0 ` V ' $ # Q 0 # 0 $ # $ # 0 & P ( Y 1 R 3 d U Q ( 1 B C 3 # ( 1 3 ' Q # P 0 P $ 0 & P 0 & P !& V 3 6" ' ! $"% 0 $ # 0 # # 0 $ # ( ) 5" 42& 1 A C D s S 3t 6!! ' $I"! 0 $2 #2 0 # # 0 $ # ( ) 5 ! 4"&& 1 3 2 $ 0 $ # P ) 5& 7""!2 I 4""26 @ C C B C ! &2" D" v""" # # $ V 4 4 $ # $ # # # $ V g 4 $ # @ Q ( # ( 3 ( & ! 6 ' P $ 0 P V ( # ( & 1 3C $ ## '" #4 X #"2"3 (2 0 ( 0 # 0 PS S P# q6 dP V$ ( 0 # 0 1 1 5 T g i S 3( ` ) Q $0 0( $ ! 5$ V c b( 73 4( 3Q Q 6 '"" (6&` '( B (( $( #0 0Q Ps # # &@ 0 $ # &V (y 9 )( ( P & & X 7 1 3( $ 05 # # P 5 ! V R T S b 7 4S X #'!!" 0'" W $ i& 4 $ #S 0P 00 P7 #S 0V $ # &! Q &( 03 &4 # 0 P P $ # !P V 1d VV 3W $ $!"b 0" b 0P 0 P3 5' i2S E G F 4'f 7' 4rf 3' ''6 ($ 8" ("' $! #"( P! 00 0%1 P"Q #P � 0x &0 @ 9 $( #V 0@ b PS VB 1" V4 37& #( # (X 3 6iw! $ 0 '6""227! (Aa 06' #!!YI! 0!' P6U A r PA ##! $VP #CP (I 0S! 5 5 qW"6 dp V!' P& 7 4 0& 3'! 'v!& $V6 #6 (b uI )b ''!! (I"q" 2"' (!&!6 $!!!# #d 0"&$ P%2$!!2 #V& #S &P0 0S%"t &q 0 # # 0 # ( ) $ # !W&" !t 1!#& "'"h" 22D"I" ""' "!6 1!! "!I 26c 8!!2" 0&" 9b"! V"Ie Q&& "2 Uf &6 P&!2I !f! & !2" &H "" f 2%" I 6 $t22"2"2" Q22"2
9 8 7 Rotate compressor at the clutch plate of the magnetic clutch in order to accelerate draining of the oil. Remove oil drain plug. Remove compressor. T T T (+119 C) T Air Conditioning Notes: If a new compressor has been installed or fresh refrigerant oil poured into the compressor (e.g. after blowing through refrigerant circuit and draining the compressor at the oil drain plug), rotate compressor about 10 turns by hand after it is installed (in order to avoid compressor damage when it is started). The piston stroke of the compressor is variable and is set in line with the refrigerant capacity requested. Mark direction of running of poly V-belt before removing; if belt is fitted on again to run in the opposite direction, it may be destroyed. Removing and installing ribbed V-belt. 15 14 13 12 11 30 E
------------ 87-47 ------------
Notes:
OCTAVIA
10 O
87
87
Air Conditioning
OCTAVIA
Air conditioning pressure switch -F129Note: If the vehicle is equipped with air conditioning with automatic control (Climatronic), the air conditioning pressure switch -F129- is tested by the self-diagnosis page 87-47.
Functions K Low/high-pressure switch (switch between contacts 1 and 2) switches the compressor off if insufficient or excess pressure exists in refrigerant circuit. Switching pressures (in bar gauge): Opens at 1.2 bar (compressor off) and closes at 2.4 bar (compressor on). Opens at 32 bar (compressor off) and closes at 24 bar (compressor on).
High-pressure switch (switch between contacts 3 and 4) switches the radiator fan -V7to stage 2. Switching pressures (in bar gauge): Closes at 16 bar (fan stage 2 switched on). Opens at 12.5 bar (fan stage 2 switched off).
Removing and installing KSeparate 4-pin connector and remove pressure switch -B- (5 Nm).
Testing operation: Test conditions l Air conditioning not operating l Fresh air blower switch -E9- in position 1 l Air conditioning switch -E35- pressed (on)
OCTAVIA
Air Conditioning
87
K-
Unplug connector -B- of switch -A- and bridge contacts 1 and 2 at connector -B-. Switch on ignition.
Notes:
If the magnetic clutch clicks when the ignition is switched on and off, either the pressure in the refrigerant circuit is too low (refrigerant circuit empty) or the switch is faulty. Hand over vehicle to a service centre workshop for testing the pressures in the refrigerant circuit. Test conditions l Air conditioning operating l Fresh air blower switch -E9- in position 1 l Air conditioning switch -E35- pressed (on) Remove pressure switch and connect again to the wiring loom. Switch on ignition.
Note: In this state, the magnetic clutch must not click, otherwise the pressure switch -F129- is faulty (although air conditioning is operating).
Air conditioning high-pressure sender -G65Removing and installing KSeparate 3-pin connector and remove pressure switch -B- (5 Nm). Replace O-ring seal -A- (10.8 mm; 1.8 mm).
The high-pressure sender -G65- is the information provider for the radiator fan control unit -J293- and for the engine control unit. It can only be tested by means of the self-diagnosis of the engine control unit 1.6-ltr./74 kW Engine, Simos 2 Fuel Injection and Ignition System, Repair Group 01, Self-Diagnosis.
------------
------------
87
Air Conditioning
OCTAVIA
Note: If the heat insulation is missing or is not properly installed, this can result in a reduction in the capacity of the air conditioning system (change in the set control characteristic curve as a result of radiated heat).
Notes:
Replace both O-ring seals -E- (16.7 mm; 1.8 mm) and -F- (7.6 mm; 1.8 mm). Seal open refrigerant lines and connections at the expansion valve. Install refrigerant lines free of stress.
------------
K------------
Remove screws -A- (8 Nm). Take off expansion valve -B- and threaded plate -E-.
OCTAVIA
Air Conditioning
87
Notes:
Replace both O-ring seals -C- (14.0 mm; 1.8 mm) and -D- (10.8 mm; 1.8 mm). Seal open connections at evaporator. If the heat insulation is missing or is not properly installed, this can result in a reduction in the capacity of the air conditioning system (change in the set control characteristic curve as a result of radiated heat).
l Version -II.-: Note: Water drain openings must not be blocked by impurities and must be positioned at the bottom.
Removing and installing Open flap -D- of heat insulating mat (at prestamped point) and remove condensation drain valve.
Notes:
Remove condensation drain valve -A- by taking down and out of floor panel; ensure it is correctly installed in the cross panel -B- when re-fitted. The condensation drain valve must not be touching the flap of the heat insulating mat -D- when installed. The condensation drain valve must not be blocked by wax or underbody sealant (version -I.-) or must not be blocked by impurities (version -II.-). If a complaint exists regarding moisture in passenger compartment, check to ensure condensation drain -C- is correctly located in the condensation drain valve -A-. If valve -A- is replaced, fit only valve of version -II.-.
87
Air Conditioning
OCTAVIA
Note: Only necessary on engines with PAS pump located at bottom (e.g. 1.6-ltr. 74 kW; 1.8-ltr. 92 kW).
------------
------------
OCTAVIA
Air Conditioning
87
K-
Notes:
Push threaded bush -B- fully into the hole of the compressor before installing the compressor. When installing the ribbed V-belt, ensure that it is correctly fitted onto the belt pulley.
Notes:
The refrigerant pipe -C- runs to the condenser. The refrigerant pipe -E- comes from the expansion valve. When fitting on the refrigerant pipes, ensure the dowel pins -F- are correctly located. All opened refrigerant pipes and connections at the compressor.
------------
------------
87
Air Conditioning
OCTAVIA
Note:
Before first operating the compressor:
Rotate compressor about 10 revolutions by hand. Start engine with compressor switched off. Wait until idling speed has stabilised. Only now, switch on the compressor and allow it to run at idling speed for at least 10 minutes.
Notes:
Replace both O-ring seals -F- and -B- (10.8 mm; 1.8 mm). Keep receiver closed for as long as possible. Do not remove caps until just before installing (the receiver contains a desiccant bag which will become saturated with moisture and thus unusable within a short time if the receiver is left open.
------------
------------
OCTAVIA
Air Conditioning
87
Take condenser together with radiator off the lock carrier. General Body Repairs; repair group 50; replacing lock carrier. KTake off receiver page 87-30. Remove bolt -D- (tightening torque 15 Nm). Take off refrigerant pipes -B-. Remove bolts -C- (tightening torque 8 Nm).
Notes:
Replace O-ring seal -A- (10.8 mm; 1.8 mm). When fitting on the refrigerant pipe, ensure the dowel pin -E- is correctly located.
------------
------------
87
Air Conditioning
OCTAVIA
Notes:
Detach compressor from bracket for servicing the magnetic clutch (do not open refrigerant circuit).
Special tools, testers and aids required Counterholder MP 9-601 Insertion tool MP 9-400 1 - Hexagon nut Self-locking, replace Tightening torque: 15 Nm Removing and screwing on Fig. 1
OCTAVIA
2 - Clutch pulley Removing Fig. 2 3 - Shims For setting size of gap between clutch pulley and belt pulley Size of gap: 0.4 to 0.8 mm Inspecting and setting size of gap Fig. 6 4 - Circlip Replace Install the right way round (flat side facing toward compressor) Ensure correctly located in groove 5 - Belt pulley With interference-fit bearing Do not replace bearing Pulling off Fig. 3 Fitting on Fig. 5 Clean contact surface before installing 6 - Circlip Replace Install the right way round (flat side facing toward compressor) Ensure correctly located in groove 7 - Solenoid coil Installing Fig. 4
Air Conditioning
87
Notes:
An overheating protection is integrated in the solenoid coil. The overheating protection interrupts the coil as soon as the magnetic clutch heats up excessively (approx. 180 C) (for example if the compressor is stiff). A protective diode is also integrated in the coil (reduces voltage peaks which may arise when the magnetic clutch is switched off). 8 - Bracket with bolt 9 - Bracket 10 - Bracket 11 - Bolt 12 - Compressor 13 - Sliding bush With thread
K Fig. 1
Notes:
Self-locking, replace. Use MP 9-601 with pin diameter 6 mm.
87
Air Conditioning
OCTAVIA
K Fig. 2
Note: If coupling plate is tight, lever off carefully with two screwdrivers -A-.
K Fig. 3 -
Insert two-legged puller -A- at shoulder -Band pull off belt pulley.
Notes:
Ensure the puller is correctly located at the shoulder -B- in order to avoid damaging the belt pulley when it is removed. Clean contact face before installing.
K Fig. 4 -
Position stud -C- in recess of magnetic coil -A-. Ensure the wiring -B- to the magnetic coil -A- is correctly routed.
------------
------------
OCTAVIA
Air Conditioning
87
K Fig. 5 -
Position belt pulley flat and use MP 9-400 for fitting on.
Note: Tighten the bolt of MP 9-400 only by hand onto the compressor shaft.
K Fig. 6 -
Measure dimension 1 between belt pulley and clutch plate (-B- and -C-) with depth gauge -A- (at 3 points). Apply 12 V voltage to 2-pin connector -D(ensure correct polarity of voltage). Measure dimension 2 between belt pulley and clutch plate (-B- and -C-) with depth gauge -A- (at 3 points). Size of gap (difference between measurements 1 and 2): 0.4 to 0.8 mm.
Notes:
The size of the gap must be within the tolerance around the entire circumference. The size of the gap can also be measured with the compressor installed. If the size of the gap is not within the permissible tolerance range, take off clutch plate and adjust size of gap by removing or inserting spacers.
------------
------------
87
Servicing
Notes:
Parts marked with * can only be serviced in service centre workshops as the refrigerant has to be extracted first of all using a service station. Observe safety precautions when working on models with air conditioning and when handling the refrigerant R 134a.
------------
OCTAVIA
conditioning
The passenger compartment is ventilated through 2 ventilation frames (in the left and right of the luggage compartment in the area of the bumper) page 80-3.
The fresh air is drawn in through a dust and pollen filter; removing and installing page 80-16.
------------
OCTAVIA
1
Removing and installing Body Fitting Work; Repair Group 70 Clipped in place
10
! 7 0 & ! & 3 & E 3 " 3 ! 7 0 % @ % 0 F B A 8 7 7 1 8 7$ 7 7 ! 0 E 3 00 8 $ $1 0 0 7 A 7 0 ) ( @ 7 8 7 0 9$ 1 # ' 8 % 7 7 $ 3B 7 7 37 7 76 6 1 ) 4 ' 5 0 0 1 3 0 % ) 8 0 )'$ C 4 D " $ $ % $ ( & ' $ % & ! $ ) C$ @ 5 8# 0$ $ 2$ $ $ 0$ 0 $ " 2 1! $$! 3$
Air Conditioning 11
87
Notes:
The switch is firmly attached to the heater control. No recirculated air mode possible in Defrost mode (recirculated air mode is switched off about 15 before air distribution rotary switch reaches end position of air flow to windscreen). 1 AC
Notes:
motor
The switch is firmly attached to the heater control. Perform operational test according to current flow diagram. 13 1 1 vent
to
16
for
vent
17
Air Removing and installing page 8738 Detaching, attaching and adjusting Bowden cables page 80-8 Connection diagram for Bowden cables page 80-8 Disassembling and assembling page 87-42
18
Removing and installing page 8740 On models with mapped cooling in allmetal version because of higher temperatures
Removing and installing page 807 Detaching and attaching Bowden cables page 80-7 Adjusting Bowden cables page 808 Connection diagram for Bowden cables page 80-8 Replacing bulb page 80-10
1 W
------------
------------
87
------------
9 A D ( ( C 9 'B 29 2 3 2 3 @ 2 7 ( 4 2 & 3 4 ' 2 ( ' 0 8 6 % 1 " 4 4 #5 & ! 4 5) F$ E 8
Air Conditioning
OCTAVIA
in
Remove dust and pollen filter together with housing page 80-16.
Notes:
When the battery is again connected, please check the vehicle equipment: - Perform coding of radio - Reset time of clock - Initialise power windows. Inspection and Maintenance Disconnect battery.
Before disconnecting the battery, determine the coding of radio set fitted with anti-theft code.
Release pressure in the coolant circuit by opening the cap at the coolant expansion reservoir.
K-
Pinch off both coolant hoses to the heat exchanger of the air conditioner (e.g. with V.A.G 3094) and detach.
Notes:
Connect the coolant hoses the right way round: Coolant hose -B- return flow to water pump. Coolant hose -A- feed from cylinder head.
Position a vessel below the connection for hose -B- and carefully blow refrigerant out of the heat exchanger (with compressed air) through the connection for the hose -A-.
K-
Seal refrigerant lines and open connections -A- and -B- at the evaporator.
Note:
A seal has to be fitted with the washers of the hexagon nuts to provide a proper seal.
------------
OCTAVIA
Air Conditioning
87
K-
Fold up the pre-punched points -A- of the heat insulation mat and remove the hexagon nuts and washers -B- behind them (tightening torque 15 Nm).
- Remove dash panel. General Body Repairs, repair group 70 Remove footwell vent page 80-15.
- Remove passenger airbag unit. Electrical System; repair group 96 Cover over all the opened connectors and air guide ducts of the air conditioner to prevent the ingress of swarf.
K-
Drill off support for dash panel at the points marked with -A- (connection points) with a 7 mm drill. Bent part -B- of the support at the specified breaking points -C- to the side in direction of arrow.
Note: After installing the he ater unit, bend back the part -B- into its original position and bolt the shaped piece marked in broken lines to the holes -A- (e.g. M 6 x 10).
Separate electrical connection between vehicle and air conditioner (plug connection and bolted-on earth cable at A pillar).
K-
Notes re installing:
Inspect all gaskets and seals at air conditioner before installing and replace any damaged gasket or seal.
When installing the air conditioner, inspect the gasket at the intake duct; it must be making contact with the vehicle body.
------------
------------
87
Air Conditioning
OCTAVIA
K Replace gasket -A- at heat exchanger and ensure that it is correctly located on the contact surface -C-. The flow direction of the coolant is marked at the connection of the heat exchanger (arrow -B-). All the cable straps which had to be taken off in order to remove the air conditioner, should be fitted on again after assembly at the same point. Replace both O-ring seals for the refrigerant pipes and the expansion valve. Install refrigerant pipes free of stress. Inspect condensation drain and condensation drain valve to ensure they are correctly installed. K Replace gasket -A- and ensure it is correctly fitted onto the evaporator connection flange.
Notes:
If the heat exchanger does not properly engage when installing in heating flap box, it should be attached with 2 suitable screws -C- (e.g. 3.2 x 20 mm self-tapping screws). Ensure the gasket -D- is correctly installed; it must not be visible after being installed.
------------
------------
OCTAVIA
Air Conditioning
87
K Replace gasket -A- and check to ensure it is correctly seated on the contact face -C-. The flow direction of the coolant is marked at the connection of the heat exchanger (arrow -B-).
------------
------------
s F q c q 6 % y $ W $ 3 W 6 yWf %& &5 7 $G )$ 10 $1 16 03 )) )R W & ) $h Wc 5 x3 4$ T 6e wb y3$ 02F )5e eBG &Y02 W0 &V 1Q &) 1P $W &R 'G $) 1$ 28 2C $ 1 W W W 5(% x31 x()( 4` xE T0 FU cd ET G` cX DT G F E E D u1 tR # 9H sS8(YHB T2S755((S(( R(5I54S(Y RS(Sg9S c5%( U5S% T5(v(XI ES57A Uia T@22 T5$2 GB4Y T15 GU HH62 qT Hv(B& $ ) & ) & 1 0 ) 3 & $ ' PH02B r$H pWI 4 " !
------------
------------
87
Air Conditioning
Air
OCTAVIA
OCTAVIA
$ & # $ 8 5 ) $ $ 7 @ 8 $ $ $9 'A' ' 6 7 3 $ 2 1 0 4 % '9 ' )' ' & & $ 5 # (' ( ( $'' ' ' ! "" #
Air Conditioning 8
87
Detaching and attaching Bowden cables page 80-7 Adjusting Bowden cables page 808 Connection diagram for Bowden cables page 80-8 Changing a bulb page 80-10
Removing and installing page 8740 On models with mapped cooling in allmetal version because of higher temperatures
Do not disassemble Detaching, attaching and adjusting Bowden cables page 80-8 Connection diagram for Bowden cables page 80-8
10 11
Notes:
Ensure the tensioning strap -A- is correctly positioned around the evaporator housing.
Note:
The gasket -A- must be inserted into the slot of the evaporator housing all round.
------------
------------
P( Q( Q XA Uu Q y y U R Q Y U x W T @' @' @ 5 r A I) ' 6 ) 3 7 @ 7 r 2 4 Aq )' 4d (1 ) ' E) ig 4 B4 4 0I 4' 3Q (5 3V 33 (U ') 44 3P 8i )( d3 P I Q R 5( H AG' AQ Ac 9( )6(6 4RI (@G( 3X 8) (e )&&e 8A 4( 3) )) 38 7) A iR( 0 B`b A Gp( P&Se&9 Q)' Q8F X8&R U3@ QW y3 y1 ) 4 ( ) 3 8 &0 C S)@ 0&2G F22R326 x4@@ ) E D B 9& a'7S@p&& Qv(h&2 QSRP Y@``(@Tr I&R)6 U9a' bG8 a`'&&r RR5sr af2t IY@ II R86 R`A6 Y' 0 3' 0 ) ( 3 ' ( ' 4 3 6 ) ( ' ' xU82&2S&&@ WT0 w3 `R(` T@I TS8 `7R `4 `3 5 1 " # " $ % !
D
------------
------------
87
Air Conditioning
motor
OCTAVIA
OCTAVIA
Air Conditioning
87
5 - Bottom part of the evaporator housing Assembling evaporator housing Fig. 1. 6 - Fresh air blower -V2 Removing and installing page 80-11. 7 - Series resistor for fresh air blower -N24 Removing and installing page 80-11. 8 - Evaporator Attaching seal to coolant pipes Fig. 2. Attaching seal to evaporator Fig. 3. 9 - Seal Attaching seal to coolant pipes Fig. 2. 10 - Seal Replace. Attaching seal to evaporator housing Fig. 4. Seals off connection area of refrigerant pipes to engine compartment.
11 - O-ring seal Removing and installing page 87-26. 12 - O-ring seal Removing and installing page 87-26. 13 - Threaded plate 14 - Expansion valve Disconnecting and connecting refrigerant pipes page 87-26. Removing and installing page 87-26. Removing and installing heat insulation page 87-25. 15 - Bolt Tightening torque: 8 Nm
K Fig. 1 -
Use suitable bolts -A- to screw together the two halves of the housing at the attachment points -B- provided.
Note: The attachment points -B- are provided around the entire circumference.
------------
------------
87
Air Conditioning
OCTAVIA
K Fig. 2 -
The refrigerant pipes -C- should be sealed off to the two halves of the housing -B- with seal -A-.
K Fig. 3 -
The evaporator -A- should be sealed off to the evaporator housing at the top and at both sides with the seal -B-.
Note: No seal should be fitted to the bottom of the evaporator (to allow the condensation to drain off).
K Fig. 4 -
Replace gasket -A- and ensure it is correctly fitted onto the evaporator connection flange.
------------
------------
OCTAVIA
Air Conditioning
------------
87
OCTAVIA
# " # C # % 3 5 ' i # # f ( C % & C & % # % C # ' ' h D D 5 ' ! C # 5 2 2 2 ) 2 ' h ( # & ! $ $ ! h # & # C # & ! ' 5 # " # & 3 B 4 4 2 2 ) & D $ $ $ f$ C # & & # & # # " %% # $ ' ' 9 e g ($ #& 0 #% % # & # %5 C # % 1 ! %f ' & & ($ % & 7 # & % % 5 8 ' ' ' ' 2 & # " & @ ' ' ( #% # C #6 ! 2 3 %56 )C 2 1 !' d%) B % ) # 0 6 " A # @ C # & % # A &8 9 2 #2 5 "2 4 2 @5 'g ') 4 & C # " # % %' 8' & ) )% $ $ % # # % 8( )' 5 & # C & 8 ) ) 8 ) % r r x u u % x w r w x q u s x r r % p t% t i G X F G F G I F I g Y P P Q E a RU # G# I " H G H V g e e c h f ` d Q WYU! S Xvt H& VUP$ H H$ Vyv VQb Y HP I R G HQ G G I F H PP P P TQ E U Q
T T Air Conditioning K K K K If no readout appears in the display: Note:
OCTAVIA
------------
------------
87
1 & % &" " " $ & o o s D n 6 5 $ & $ & 0 " & @ A r 4 F % % 5 " $ " 0 " @ p r ! % 5 $ 1 $ 0 " " @ p r % 5 $ & 0 " & @ n r 59 0 " & @9 69 r9 q 5# " 0 & " & " or @# 8o % 3 5 $ & 0 " & 0 " @ op 6n 5@ " " $ " 0 " & 0 # " @# 81 A 01 & k g l# d l m j f f d f i S i S S v V Q# Q S# a## S5 a# e5 i5 d R# d R d b g0 S q e S d UE h9 h5 p T V & 1 " F % P I 5 A "#5 & 1 15 & " & " " $ # H %Q 9 % ' B # "I 6 #5 "# " & " #R # 0 " & % ! D '# E & " # " & 0 & # " % 9& %I % % ` I # $5 &B # 1 0 " 4 D & Q Q R S R R q a S q R a V h Q Qh Q Sd ` a#h ae I R d a S a d q R ` q a d e Ub he p WR S R S S q S QI Q Q fS cWYUYYW& Re9 S13 bd d&0 qW9 aYg RYU S d8 S% a `& e S gU `( R7 g T V Y Q$$ Q `b9 Rh" R@ Re" `d0 Sd S a5 S$ g 6 b q q6 bB a d S a # pYUU VTT h V Yi YW ( Q Q c X R S S q6 d b RA d R ` h V p" # y V SI i" r uI s) tH QG S5 `S Rq$ SI" eUY! d#g dw b SU Rw eT9 S' R a gUgA b a S g Uq V h p Y Qx$ Q9 " $ " SV# bdW# ag4 d$1 d qd& a S e g Sg#YW$ e SUUY5 dU# d a eU iYg0 S& dYUWU" R1 ( % pU#" V! h! TS! V5 W YH# WWWU Q Qg Q" Q f R cWUYUT$# e"Y% aeYE S!" X#D `"B aUUF dvYU" Sg2 dUUTU dd' bY a `Y' R S2 9 VT" TWC WgUY"
T T T T T
------------
------------
87
Air Conditioning
K If
Note:
Notes:
HELP
by
OCTAVIA
OCTAVIA
Notes:
e g w h e h e z { f h g he f w g ee ee ex ek f eh h e e dx e x x x h w x e }h } } e } { k e k k z {xk j yvit wdf he xiilih gd{ dx| xgg xw{ eh } wfu xge eit x gh h e w d e{ ij f i e di x e d f d ke i} ik e ie d ~t rh ye y i di xxili x Xy toq u 'no %sr %y "sn %n o % "q %s 's # q qp Xqm % " % # % q ) ) ) X X EQ # % % T # " % ' # & )Y ) X p % # % % & % ) ) ) % " % % ) X X X % # % ) ) f E ' % " % & " % & " r ) q i Ew T4B A v #X8 3 3 # B # # % & " % & % %8 ) R f E # # " # % & " # &p & V S ) U g X c %H # " ) ) X Hp E & '& % #& " # # % ' Yd& aE `' V# F b# E# #& %& & & ' # & )e F # T % ) ) ) V U T&W H# #h "&d! H& #d& &$ #&# " % && 0 # % & e $ F& ) % H H &H & H % &h # R R Pe I&& G S#" Q#" F D( AE# CB C30) 6 4&E& 7$ 2E# 8 7' 5&9! 6$ 8$ 2 4 5 5( 3 3 @g 1#
Air Conditioning
87
key.
After completing repairs, always once again erase and re-interrogate the fault memory with the vehicle system tester V.A.G 1552.
The fault type may also appear additionally in the fault table.
If faults occur only occasionally, these are displayed as sporadically occurring fault (SP).
All the possible faults which can be detected by the Climatronic control unit -J255- and displayed on V.A.G 1552, are listed below arranged according to the fault code.
If a complaint exists regarding the Climatronic, but it was not possible to detect any fault, perform the function Final control diagnosis 03 page 87-59 or the function Read measured value block 08 page 87-64. If the display flashes although no fault has been detected, initiate one after the other the function Code control unit 07 and the function Basic setting 04 page 87-61. It may then be necessary to carry out fault finding on a complaint-related basis without self-diagnosis.
on
------------
------------
87
------------
OCTAVIA
on
00281
Short circuit or open circuit at cable - Test road speed signal in measured value block or at plug connections for road speed 001 page 87-64. signal from engine control unit to Cli- - Test wiring and plug connections to control unit matronic control unit according to CFD. Speedometer sender -G22- faulty (only if speedometer -G21- also not operating) - Check speedometer reading.
This display only appears if final control diagnosis has been performed before interrogating the fault memory. This fault is erased in the fault memory of the control unit after the ignition is switched off. If -G68- is faulty, the fault again appears when driving.
Supply voltage
Alternator faulty
- Test alternator: Current Flow Diagrams, Electrical Fault Finding and Fitting Locations
- Test supply voltage (voltage at terminal 15) with function 08 Read measured value block page 87-64.
- Test supply voltage (voltage at terminal 15) with function 08 Read measured value block page 87-64. - Repair wiring or plug connections according to CFD.
- Test alternator: Current Flow Diagrams, Electrical Fault Finding and Fitting Locations
1)
A fault is detected by the speedometer sender -G22- and not by the road speed sender -G68-. The fault is only detected if no road speed signal is measured during 5 driving cycles (start, driving at more than 15 km/h, switching off engine) within 4 minutes after start of engine.
------------
OCTAVIA
87
on
00538
- Test cables and plug connections to Climatronic control unit -J255- according to current flow diagram.
- Test operation of AC control motors by selecting 03 Final control diagnosis page 87-59.
Potentiometer -G92- or poten- Separate plug connections of the stated compotiometer -G112- or potentiometer nents one after the other, erase fault memory -G113- or potentiometer -G114- faulty page 87-62, and once again interrogate page 87-51. - If the fault Reference voltage is now no longer detected, replace the appropriate positioning motor, which leads to the fault after it is plugged in to the plug housing. Climatronic control unit -J255- faulty - Replace control unit -J255- if necessary, then select the following functions one after the other: 07 Code control unit page 87-63 04 Basic setting page 87-61.
005761)
Terminal 15
Cables or plug connections to Climatronic control unit -J255- faulty Battery discharged Alternator faulty
- Test alternator. Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder - Test cables and plug connections to Climatronic control unit according to current flow diagram.
- Test battery. Electrical System; Repair Group 27 - Test alternator. Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder - Test cables and plug connections to Climatronic control unit according to current flow diagram.
1)
------------
------------
87
Readout on V.A.G 1552 00603 Footwell/Defrost flap motor -V85-1)
Air Conditioning
OCTAVIA
Rectifying fault
Short circuit or open circuit at wiring or plug connections to footwell / Defrost motor -V85-
- Perform final control diagnosis page 87-59. - Test -V85- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Replace -V85- page 87-84. - Then, perform function 04 Basic setting page 87-61.
-V85- faulty 006062) Two-way valve for coolant shutoff valve -N147Short to earth Open/short circuit to positive Short circuit or open circuit at the wiring or plug connections to the twoway valve for coolant shutoff valve -N147Climatronic control unit -J255- not, or incorrectly coded 007052) Radiator fan stage 1 relay -J279Short to positive Short to positive at wiring or plug connections to radiator fan control unit -J293-J293- faulty -N147- faulty
- Test wiring and plug connections to radiator fan control unit -J293- according to current flow diagram. - Replace -J293-. Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder - Test wiring and plug connections to radiator fan control unit -J293- according to current flow diagram. - Replace -J293-. Current Flow Diagrams, Electrical Fault Finding and Fitting Locations binder
Open circuit or short circuit to earth at wiring or plug connections to radiator fan control unit -J293-J293- faulty
This fault is detected in Basic setting 04, Final control diagnosis 03 and in the normal mode. Both end stops must be reached. Applies to models from 08.00.
------------
------------
OCTAVIA
87
on
00779
Short circuit to positive or open circuit in wiring or plug connections to outside temperature sensor -G17-
- Test -G17- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
Short circuit to earth at wiring or plug connections to outside temperature sensor -G17-G17- faulty
- Test -G17- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Replace -G17-. Electrical System; Repair Group 90
00787
Short circuit to positive or open circuit in wiring or plug connections to fresh air intake duct temperature sensor -G89-
- Test -G89- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
Short circuit to earth at wiring or plug connections to fresh air intake duct temperature sensor -G89-G89- faulty
- Test -G89- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Replace -G89- page 87-74.
------------
------------
87
OCTAVIA
on
00792
Short circuit or open circuit in wiring or plug connections to AC pressure switch -F129Incorrect filling of refrigerant circuit Poor engine cooling
- Test -F129- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
- Hand over vehicle to a service centre workshop. - Test engine cooling. Engine, Mechanical Components; Repair Group 19
-F129- faulty
00797
This readout only appears if final control diagnosis has been performed before interrogating the fault memory and the pressure switch could not be checked (e.g. at a measured outside temperature below 12C). This fault is erased in the fault memory of the control unit after the ignition is switched off.
Short circuit to positive or open circuit at wiring or plug connections to sunlight penetration photo sensor -G107-
- Test -G107- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
Short circuit to earth at wiring or plug connections to sunlight penetration photo sensor -G107-G107- faulty
- Test -G107- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Replace -G107- page 87-74.
1)
This fault cannot be detected at an outside temperature below 12 C, or if -G17- and -G89- fail. The switch is a triple switch. The 0.2 MPa (2 bar)/3.2 MPa (32 bar) switching part is tested, but not the 1.6 MPa (16 bar) switching part.
OCTAVIA
! # "
Air Conditioning
87
on
00818
Short circuit to positive or open circuit at wiring or plug connections to evaporator outlet temperature sender -G263-
Short circuit to earth at wiring or plug connections to evaporator outlet temperature sender -G263-G263- faulty
- Test wiring and plug connections according to current flow diagram. - Replace -G263- page 87-84.1.
00819
Short circuit to positive at wiring or plug connections to high-pressure sender -G65-G65- faulty
- Test wiring and plug connections to high-pressure sender -G65- according to current flow diagram. - Replace -G65- page 87-25.
Short circuit to earth or open circuit at wiring or plug connections to highpressure sender -G65Open circuit or short circuit to positive or to earth at wiring or plug connections between -G65- and Climatronic control unit -J255-G65- faulty
- Test wiring and plug connections to high-pressure sender -G65- according to current flow diagram. - Test wiring and plug connections to high-pressure sender -G65- according to current flow diagram. - Replace -G65- page 87-25.
- Replace Climatronic control unit -J255- page 87-15. - Then, select the following functions one after the other: 07 Code control unit page 87-63, 04 Basic setting page 87-61.
87
OCTAVIA
on
01044
01087
01206
- Test dash panel insert and replace if necessary. - Test stationary time signal with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
Short circuit or open circuit at wiring or plug connections to Climatronic control unit -J255-
- Replace Climatronic control unit -J255- page 87-15. - Then, select the following functions one after the other: 07 Code control unit page 87-63, 04 Basic setting page 87-61.
1)
The permanent stationary time signal is supplied by the dash panel insert. The Climatronic control unit -J255analyses the time measurement after the engine is switched off in order to replace the measured values of the outside temperature sensor -G17- and of the fresh air intake temperature sensor -G89- with the temperatures used during last engine operation after the vehicle is stopped (ignition off) and then re-started. The measured values would otherwise be falsified when the engine is not running by the heat radiated. The stationary time signal is supplied only after engine start.
OCTAVIA
87
on
01271
Short circuit or open circuit in wiring or plug connections to temperature flap motor -V68-
- Test -V68- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
-V68- was installed without having performed function 04 Basic setting -V68- is blocked -V68- is faulty
- Test end position of motor -V68- when installed page 87-59. - Perform function 03 Final control diagnosis page 87-59.
01272
- Replace -V68- page 87-82 and perform function 04 Basic setting page 87-61.
Short circuit or open circuit in wiring or plug connections to central flap motor -V70-
- Test -V70- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
-V70- was installed without having performed function 04 Basic setting -V70- is blocked -V70- is faulty
- Test end position of motor -V70- when installed page 87-59. - Perform function 03 Final control diagnosis page 87-59.
- Replace -V70- page 87-83 and perform function 04 Basic setting page 87-61.
1)
This fault is detected in Basic setting 04, Final control diagnosis 03 and in the normal mode. Both end stops must be reached.
e d f e e e g h 4 $ 2 $ 2 ) ) B 9 @ Q 7 W P 0 0 4' & T '2 2 $ 2 # # B B B 5 S 9 D W Q $ 2 b B c Q & T $ 2 )! ) 2 ' ' D a ` P V Y " T 2 $ 2 D " & $ 2 ' ' ) ' $ ' 2 # $ D D I $ 2 B W @ Q &( ") & U " T4 ' 2%0 0 2 ) 2 # B SV D( D 5 Q P 1 9 I b Q 4d 4$ 4 2 ' #!" $X) 2 X!( $R 2# 0 B(# B4 5R(4 6 W2 Q S @5 64 90 X!4 " $ 2 B3 b Q c! X9 !( !3 !" & $) 2' )& )!' '4 # ) T5 2(# (4 DR5 V %!45 a(X `# P4 Y 0 "A &! T4%#!!0 2 $ 2& % # (2 D! )9 9 !4%44 "& &%##! $Q' 22! '!V#!' ''3 1 )1u '%44 $%# 0B '5 2 #(# $! () D# D! I3 XD 4444 & ! $ 2 24 )4 ' #!04 ## B%69 @!6 Q%6! W&0w 1# BBf ! R4 4!#0!4 4% "(% &f@ &%)A U(X#& " T 4)4B 2 4 )!4 #B ! %C '89 2!!( 26( # $40 #! (T DR# 5$ 17 6( 34 S!)( C##!x D" V'22 Qy P4 I' %(X5 5 6 3 6 (%4(0! F'` # vi H GCa 1 ' 34# 2 9 a W %# # 44 B) s s E"%%! %B 8#P 9) # $%%%4 P %# q p #i h (1 (!%%2 t E r g
on ----------------------Short circuit or or Short circuit or or
------------
87
Air Conditioning
circuit to
circuit to
or
or
OCTAVIA
to to
OCTAVIA
) 1 0# $# '( & #$ & (' &" (( $! %
Air Conditioning
87
on
012961)
Short circuit or open circuit at wiring or plug connections to middle outlet temperature sender -G191-
- Test -G191- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Test -G191- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram.
Short circuit to earth at wiring or plug connections to middle outlet temperature sender -G191-G191- faulty
01297
Short circuit or open circuit at wiring or plug connections to footwell outlet temperature sender -G192-
- Test -G192- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Test -G192- with 08 Read measured value block page 87-64. - Test wiring and plug connections according to current flow diagram. - Replace -G192- page 87-74.
Short circuit to earth at wiring or plug connections to footwell outlet temperature sender -G192-G192- faulty
1)
-----------------------
------------
87
Air Conditioning
OCTAVIA
------------
-----------------------
} t # u } n" j | t # " # # t ~ y k j # # t | # l # u k v v t y x u u u z # "| #n l # l t l # t # r r k$ # u s u q n n l l# ! " lw p$ ol mt k d i h{ i d g x h# c D Q g e Q S g e D Q cj g d 9# h H Q c g d D C D C Q C S A 9 B P H D C D uE cR DIe CG C Q Q C Q Q g Q D C Q Q S F y y y y x h h H f QQ D C D C D Fd C S g S Q g Ee @ @ S R p B i Q c g 9 Hh H T fh CEH QGRGE SIg gf Q g Q e g Q GEEE Fh PC P E hE h u HIxD f fR DEh C DI CG D C S g S Q e @ @EH EI yEGEB pE B iEC x q H D @ B wGE B v i uh He H C CdS cEEGIF DIeS CGeIhEIG gFD DgF CFC Sf SFFIC Q@ eHE Dp DGC CEIGD SIhh cIQ dC SIq DC gE FS cIID DIGC Q D D D S c Ed EED PFFIhRFE Pe b IFEIC GEE T Q B 2 0EgIIGEIG rgIR 0Q 0W 0 tSY@ sIGcIG3 'WSID `E71 &4 )FF 'F9 &H 'G@ `A ) &C V ) & 1VE3 1V 1ED 7 %RIESE adI@ YUIE aD WSC X 5 aQ aGP YF' 8 % 6 (
T
on
OCTAVIA
Air Conditioning
Final control diagnosis has to be performed when the engine is not running, ignition switched on and Climatronic switched off (pushbutton for Blower slower page 87-73, item 17).
Notes:
No control of the Climatronic system takes place during final control diagnosis.
To obtain meaningful results, final control diagnosis should be carried out at an ambient temperature shown in the display of the operating and display unit of at least 12 C.
------------
------------
87
87
Air Conditioning -
OCTAVIA
Press keys 0 and 3 for the function Final control diagnosis and confirm the entry with the key Q.
K Readout in display: The following tests are performed: Readout of display of operating and display unit -E87- page 87-60. Function test of the 4 positioning motors. Test of the current path to fresh air blower -V2-. Test of switching operation of magnetic clutch -N25- of control unit. Test of all the sensors. The test procedure is completed after about 30 seconds.
K Readout in display: If Function is unknown or cannot be carried out at the moment appears in the display, final control diagnosis is completed. Press the key.
Note: After completion of final control diagnosis, interrogate fault memory page 87-51. Testing readout of display of operating and display unit -E87K Complete readout in display Note: All the segments in the display appear during the duration of final control diagnosis 03. If this is not the case, replace the Climatronic control unit -J255-.
------------
------------
OCTAVIA
Air Conditioning
87
Basic setting
Note: If the display flashes after Ignition on although no fault was indicated by the function 02 Interrogate fault memory, perform the function 07 Code control unit and then the function 04 Basic setting. Connect vehicle system tester V.A.G 1552 and select the Climatronic control unit with the address word 08. (Connecting vehicle system tester and selecting Climatronic control unit page 87-49.) Interrogate fault memory page 87-51 and rectify any faults displayed. Erase fault memory page 87-62. Check coding page 87-63 and correct, if necessary.
K Readout in display (function selection): HELP Press keys 0 and 4 for the function Basic setting and confirm the entry with the key Q.
K Readout in display: Press the key 0 three times for display group number 000 and confirm the entry with the key Q.
Note: When all the positioning motors are moved as far as the end positions, the Climatronic control unit -J255- stores the values of the potentiometer and thus adopts the basic settings of all the positioning motors. System in basic setting 0 XXX XXX XXX XXX K Readout in display: Note: The movements of the four positioning motors can be followed in the display. The changes to the feedback values, however, do not provide any indication of a faulty positioning motor.
------------
------------
87
Basic setting Enter display group number 000 Basic setting 0 0 0 0
Air Conditioning Q K Readout in display: 0 Confirm the entry with the key Q.
OCTAVIA
K Readout in display: If the readout is 0, basic setting is completed. Faults detected by the system are stored in the fault memory. Press key.
X faults recognized!
Test of vehicle systems Fault memory is erased! Test of vehicle systems Select function XX
------------
' ' 7 85 $ " 4 ( 2 3 2 && ) 1 ' ( " $ # " " 0 ) ! % 6% &
Press the keys 0 and 2 for the function Interrogate fault memory and confirm the entry with the key Q. K The number of stored faults or no fault recognized appears in the display. Press key. The faults stored are displayed one after the other. After the last fault has been displayed, rectify the faults according to the fault table page 87-51. Press key. HELP K Readout in display: l Fault memory has been interrogated. HELP K Readout in display: Press the keys 0 and 5 for the function Erase fault memory and confirm the entry with the key Q. K Readout in display: Press key. HELP K Readout in display:
-----------Edition 08.98 S00.5102.51.20
HELP
K Readout in display:
OCTAVIA
A $ 9 1 ! @ " 7 ! Y V " " 5 ) ! 0 1 " " B 3 9 C ! 0 ! Y V a `4 W b 3 ! ## # C " V $ # ! # W 5 " " " $ 9 1 4 ! # ! @ VB " ! B B 2 # I1 I V G# F E8 P#3 H % % Q & R R # I I G F EX PB H D 3 C # C 0 ! 0 @ C $ @ ) !3 0 1 " " B# 9$ $B B T 1 ! 1 " A0 @B8 4 7! BU S ' 2 ! # 1 # ' "! 6 " 5 4 # ) " ! 0 13 23 #3" # ! " ! "# %" & & ( ' '
Air Conditioning
87
Ending
the
the
the
the
off
to the
Coding
Notes:
Each replacement Climatronic control unit -J255- has to be coded after being installed.
Each time after coding the control unit, carry out the basic setting (function 04).
If the coding displayed does not match the vehicle or the equipment, the control unit has to be coded. The display of the operating and display unit -E87- flashes for 15 seconds if the control unit -J255- has not been coded. vehicle system select the
the
vehicle system
the the
the
------------
------------
h 1 1 b H a a C R 4 (b 11 1C 4 ( ( % ' 1 ' % ) 1 a2 G I C G f2 %1 1 ( ( 1 ' ( % 1 G% a G $ f % b ( 2 1 G e G E R 1 6 % ( ( A V W 4 (G %2 '` )' h 1 2 % 2 1 1 % % F $ G G G 83 4 1 1 1 2 1 2 b 2 1 ' 1 ` ( Bc B8 F a 2 0 #02 53 xd x v 8) 0b p4 q p w q u p t y 3) )&&) r i r f' 0 %0P 1 b ' ( % G1 G 1 1R( e(3& CP3 X 41&0 %g&2 001 bb 1a 21 (Y %' 11 2 % 1 G2 a2 D` F %'& ( 1)0 () % ( % ( 1 )( ' ( 1 ) a8) G' G Y 1 ( 6 ( Ba A0&R De E& 9 CP 5 @ 4 !& "0 58 $P $ # 8 1 1 ' 7 BP A( 9 DP C 5 4 1( (c 6I () 2b 12 % 0@ &P ! " 5 $ $ # 1&2 ( 21 % ' ) ! " $q $p $P #P s &&' ) 3 X 8d 4 ( % ' 1 1 b H&g a a C 4X %00&Y 1)6 2) ( 20) V (5 11 15 (2 )8 ) h&300&1 1&20b %(2 1EW (803)1 (XG ' ` &0) ' IGa a04 a$ I' E1 G1 0 U 4 ( 1 1 ( ' $E $2 $W #( S $' P P P G fRA0& T(& %0P) P3 b)1) (0P 20RF %Q$ 1100 g030I ( 1 ' H&3 GP0 &2 0R( GF G
01000
------------
------------
87
Air Conditioning
Note:
The Climatronic control unit uses the code which is entered and which appears in the display, only after the ignition has been switched off once.
Note:
The Climatronic control is in operation during the function Read measured value block.
01000
11010
11000
OCTAVIA
OCTAVIA
Air Conditioning K Readout in display: Q Enter the desired display group number.
87
Read measured value block Enter display group number XXX Read measured value block Enter display group number 001 Read measured value block 1 2 1 3
K Readout in display: Notes: Explanation of the readouts in the individual display blocks page 87-66, List of available display group numbers.
If the specified values are achieved in all the display blocks: Test of vehicle systems Select function XX HELP Press key.
After completing the function Read measured value block, interrogate fault memory page 87-51.
higher lower
skipping
V.A.G 1552 Press key C Press key Press key
-----------------------
87
------------
OCTAVIA
Display block 1
Designation
Compressor, magnetic clutch -N25(code number 1 up to 17 states reason for switching off N25) 0 N25 is not switched off. 1 N25 is switched off by AC pressure switch -F129- because of excessively high pressure in refrigerant circuit.
N25 is switched off because the fresh air blower -V2- or the fresh air blower control unit -J126- is faulty. 3 N25 is switched off by the AC pressure switch -F129- because of insufficient pressure in the refrigerant circuit. Is not displayed.
N25 is switched off for 4 seconds (not a fault). Code 5 appears only for 5 seconds. If display remains, test engine speed signal.
N25 is switched off, ECON mode (not a fault). 7 N25 is switched off because the delivery of the fresh air blower was switched off at the fan button (not a fault). 8 N25 is switched off because the ambient temperature is below 3 C (to prevent icingup, not a fault). If necessary, test temperature sensor -G17- and -G89-.
Is not displayed. 10 N25 is switched off because the voltage in the electrical system is less than 9.5 V. 11 N25 is switched off because a coolant temperature of more than 118 C was detected (as a protection against overheating of engine). N25 is switched off by the automatic gearbox control unit or by the engine control unit through the Climatronic control unit -J255-. 13 N25 is switched off because the supply voltage (terminal 15) is more than 17 V.
N25 is switched off in order to prevent icing-up of evaporator (not a fault). Test -G263-, if necessary. N25 is switched off because no or incorrect coding of Climatronic control unit -J255-.
N25 is switched off because of fault in cable connections to magnetic clutch -N25-. 17 N25 is switched off because of fault at high-pressure sender -G65-.
------------
OCTAVIA
Air Conditioning
87
Display block 2
Designation Engine speed detected (code 0 - no) (code 1 - yes) Possibly: on off
3 4
002
1 2 3
Stationary time (code 0 up to 240 - time for Ignition off in minutes) (code 250 - battery was disconnected) (code 255 - transmission fault) Temperature flap positioning motor -V68(code of measured value: 0 up to 255) (permissible variation from specification 2) Temperature flap positioning motor -V68(specification: 0 up to 255)
Temperature flap positioning motor -V68Flap stop: cold (code 0 up to 149 - V68 faulty) (code 150 up to 250 - V68 is o.k. provided basic setting 04 has been performed) (code 251 up to 255 - V68 faulty) Temperature flap positioning motor -V68Flap stop: warm (code 0 up to 4 - V68 faulty) (code 5 up to 100 - V68 is o.k. provided basic setting 04 has been performed) (code 101 up to 255 - V68 faulty) Central flap positioning motor -V70(code of measured value: 0 up to 255) (permissible variation from specification 2) Central flap positioning motor -V70(specification: 0 up to 255)
003
1 2 3
Central flap positioning motor -V70Flap stop: air to dash panel vents (code 0 up to 149 - V70 faulty) (code 150 up to 250 - V70 is o.k. provided basic setting 04 has been performed) (code 251 up to 255 - V70 faulty) Central flap positioning motor -V70Flap stop: air to footwell/Defrost vents (code 0 up to 4 - V70 faulty) (code 5 up to 100 - V70 is o.k. provided basic setting 04 has been performed) (code 101 up to 255 - V70 faulty)
------------
------------
W ' R ' G 7 R G 7 ' R !4 ' ((B (E (4 A7 4 ' &4 & % 3 E5 R0 R @% 0 4 D 3 4 4( A 4 4 ( D " 2 & ' 3 % %D EV ' R R D@ 35 @ 0 3 & D B (5 5(& A 5 ( & % D 2( &4 ' E 3E C( RT D4 R D 3 @D 04 3 3 " D ( 4% 4 5 ' "4 4 & 4 %4 % & ' B4 & 5 E R% Q DBD 3 "(4 D R 4' 43 4 2' 'A ' U ' @ ( ' D 4 ! 34 C D D0 D $& 3 B% ( 4 A & E P 0 3 D I ( (% 4 ! 4Q 4 ' & 4 ' 2 % 2 3 5 3 ) 3%D D D3 D G H ' % " 4 A E ) 3 5 '(3 3 3 & 2 %" % % E ) 34 D ( 5 7$& 3 3 C F 3 4 A E 3 ) 4 'F '% &7 4 2 %( 2 & 2 & ( 3 ( ( ' & & E ) D A E 3 ) 7 5 'A 4 4 & 4 (5 % % 4 & % E 3& D 7$ 3 3% ) C % 3 4 A E ) @ 3 7 & & '4 '2 2 $ &$I 2 2B % ( D ( ( '% % & & % E$ D ) & 2 "1 ( '" % & & % E$% )% 2 D 5 ' C ' 2 5 % &" 2 2 9$%1 2 & 8 4 4 ' 2 % % 3 7B 3 (2 ( '"% & & % E%1 2 D )% 4 A S ) 0 7" 3 B B 5"$ 'Q"" $D"I % $"$ & (B (2 2 %G %4 %$ ( D 32$$ D% 72 3% 32 $ ) C 0 3 4 A 3 ) 0 % "$ S 2 & & 3 ( (( ! '$%" "% ( F & & D % ) 0$(% A$ ) 0 7( 3 $ 52 '&""" 2 &" 4% & 5 %$ %" %( ( % 3! D%3 7 7$& 3 3 C ) 0 ( 4 A $ 3 ) 0 @ ! " & & ( (2 ! '% 2 ( ( & & %B"$ 2 ) 071 & 2 2 1 1 ( (B( ! '" "6 ("1 $1 1 1 & & %"$ %1 )7"%"" 0 5 '% ' %% (1 $$ &% 2$ 2 6$ % $ 1 9 % & 77%1 8 $1 % 4"1 41 5 6$$ "$6 6 6 '"" " 2 "$ 3$"" 7"%% 3 $$ ( (B6$ ! '"% %#"" (1 (# "$ % "1 &1 &$ "# %B"%# $ $ 1 %% $ "6 )7"% 07$ "" """ " " ""
-----------Display block play in 0 up up up air 0 up up up 0 up air 0 up up up air air air air air an is up up is sensor
------------
87
Air Conditioning
0 up
0 up
air
in
sensor in
abnormal
by
air
passenger
is
is
in
0 up
0 up
is
is
sensor 0 up
passenger
is
basic
basic
sensors
basic
basic
sensor
been
been
been
been
appears in
OCTAVIA
is
is
w w f g u w w y ` # ( 4 ' $ $ 1 1 ! ` # 4 ' 1 1 ' 2 # g # $ # $ # # 4 # ' & ' $ H 1 f 2 3 3 # ( # ( # 5 h y B$ 6( 6' ' # 4 # $ & (' 1 #q &9 $( ' &u i '$ q 4 $ 52 )& )4 ) )! 1 1 E H$ #d 2 Eu E$ BA Pi % ` 3 ( 4 # ( # # ' 1 ' D #u 4 $ ' # # ' $ e 1 ' # ( d ' Dy 2u 3 4u (y #x $u ( # 4 # ' $ ) E V ` # ( 4 ' $ $ 1 1 ! ` # ( 4 ' $ 1 1 ` #vr (e 4ti ' $ 1 1 c 6( 6u 9x 2xrv 9 Dv D 9y 9 #5i ($i r ' ( $y # y (u ( % a)p !qr `q Ey X ` ( 4 ' $ #y 1 1h 2q 9rv 2 9 3i #S &y (x u #u (s # # Irtr 1 B F X S# 9 3) ')P% $ (%%5 #U 4 5 8 $ ' ( ( 3 # # W$ )$ I( ' $Y V 2 2 2 3) #%Y ( # $ # ( ( ISP 1B B5 6 D # # I8 b C E P D 9 ( # $ 5 ' # # I%5% )% %% T D ( # $ # ' Q G I)8 I Q ' ( 4 $ I 6 D # # $ I) ) C E @ 2b 2 9 2 3 #8 (P # ( # $ ' # ASB B 1P 6# 6$ 2 2 3 #5 ' # # ( $! # 4 # # 55 5 ( 4 ( 7P%5%% G( 1P5 H @ 2b 2 9 2 3 #B (P # ( # $ ' # 1P A58 B5 6)5 65 2 3 # ( # 4 # ( $ F65 E 7)S) G9 " @) 2P 2 9) 2 3 #S8 ( #) (b #P $P ' # 5 APB 1) B! 69 65) D 2R8 2 3PR #B5 ')S8 #58 #R) ()8 $))8 #) 45 # # 56 # 7%5)8 $%% 55 55 1 C @5) 2% 9)P 2 28 #S%5 (UP ' # 3%Y #) ( #b $ 58 A5)Y 15 B 6P%))5 65)) 2P) 2 3)%Y #55 ')5 #)5 #)5 (B $R) #%6 45 555 #) #%) # ) 155 0 1 1 75) P% 5)5 ' P% (Y '%% & # $ )%%%% " %P
Display group number
After completing the function Read measured value block, interrogate fault memory page 87-51.
Note:
OCTAVIA
Applies
is
Display
in
on
Display
erminal
panel
air
air
in 0
Air Conditioning
in
in
sensor in
in
in
in
on 0 up
in
------------
------------
87
87
------------
Air Conditioning
OCTAVIA
conditioning
Notes:
When the AUTO button is pressed, all the settings which vary from the automatic mode, are cancelled.
In the ECON mode only the compressor is switched off, the heating and ventilation mode continues to be controlled electronically. If a variation is made from the automatic mode before switching off the ignition, the functions selected remain permanently stored. Only the *Recirculated air mode function is cancelled 20minutes after switching off the ignition. Variations from automatic mode Owners Manual.
If all the symbols in the display panel of the operating and display unit of the Climatronic -E87- flash after the ignition is switched on, there is a fault in the system. In this case, first of all interrogate the fault memory page 87-51.
------------
OCTAVIA
9 4 E H G 0 3 2 I606FF IC7' )B6' 93B@ E@8@6 G57 997 59@3 953 9'G 4@9 7A G5 E0 7A H4 G4 0D 5 7& 4 ) ) 0 3 30 39 2F4 ( 2 1 D8 " " ! % # $
Air Conditioning
87
In the automatic mode -8- an average blower stage is displayed irrespective of the actual blower speed.
If the road speed drops below 15 km/h and the coolant temperature is higher than 70C, no change occurs to the temperature displayed. In other words, it is not the actual measured ambient temperature which is displayed as this could be falsified at low speeds by the heat dissipated by the vehicle engine.
------------
------------
87
Air Conditioning
OCTAVIA
------------
% $ " " # $ ! # ! " " "
7 When pushbutton -14- is pressed, the display for air flow to footwell appears or goes out. When pushbutton -15- is pressed, the display for air flow to head appears or goes out. Switching over from Celsius to Fahrenheit and vice versa: Press and hold pushbutton -11- and then press pushbutton -9-. The appropriate unit of measurement for the temperature appears in the display.
-----------Edition 08.98 S00.5102.51.20
OCTAVIA
8 - Display AUTO: for automatic mode In the automatic mode, the Climatronic maintains the selected interior temperature fully automatically. In this case, the temperature of the air flowing out, the blower speed and the air distribution are varied automatically. ECON: for cooling system off In the ECON mode, only the compressor is switched off; the heating and ventilation continue to be controlled automatically. OFF: entire system switched off Switch off with pushbutton -17-. 9 - Pushbutton for automatic mode 10 - Dash panel temperature sensor -G56and blower for temperature sensor -V42 Installation point for right-hand steering models 11 - ECON pushbutton In the ECON mode, only the compressor is switched off; the heating and ventilation continue to be controlled automatically.
Air Conditioning 12 - Pushbutton for warmer 13 - Pushbutton for colder 14 - Pushbutton for air directed to footwell 15 - Pushbutton for air directed to head 16 - Pushbutton for blower faster 17 - Pushbutton for blower slower Switching off air conditioning: Press pushbutton often enough until the display OFF appears (blower speed: 0). 18 - Pushbutton for fresh air/recirculated air 19 - Dash panel temperature sensor -G56and blower for temperature sensor -V42 Installation point for left-hand steering models
87
------------
------------
87
Notes:
Before disconnecting the battery, determine the code of radio sets fitted with anti-theft coding.
------------
Air Conditioning
OCTAVIA
Important!
Disconnect the battery earth strap before commencing any work in the electrical system.
When the battery is re-connected: - encode radio, - re-set clock, - initialise all power windows. Inspection and Maintenance
Parts marked with * can only be serviced in service centre workshops as the refrigerant must first of all be extracted with a service station.
------------
OCTAVIA
1
2 ' 4 % @ $ 9 7 2 ! A @ ! # " $ $ % 9 % 2 1 2 2 0 ( ) ( ) 8 4 3 ! ! 2 0 ' $ & % # " ! # 5 ' 6 7
Air Conditioning 7
87
Removing: lever out carefully, unplug connector from sunlight penetration photo sensor -G107-
Task: controlling temperature flap and fresh air blower in line with intensity of sunlight Emergency mode if it fails: control unit -J255- adopts fixed value Testing: by self-diagnosis Removing and installing Fig. 1
The control -J255-, operating display unit -E87- and dash panel temperature sensor -G56- with temperature sensor blower -V42- are a single component which cannot be dismantled Testing: by self-diagnosis Operation and function page 8771 Removing and installing page 8779 After replacing: Code control unit function 07 page 87-63 and then perform Basic setting function 04 page 87-61
Unit with warning light switch Removing: lever out carefully, unplug connector from warning light switch
Only with Climatronic Located in air guide duct for dash panel vents Remove and install together with dash panel
The control -J255-, operating display unit -E87- and dash panel temperature sensor -G56- with temperature sensor blower -V42- are a single component which cannot be dismantled Testing: by self-diagnosis Task: controlling temperature flap and fresh air blower in line with temperature Emergency mode if -G56- fails: continuous operating with assumed value of +24 C After replacing: Code control unit function 07 page 87-63 and then perform Basic setting function 04 page 87-61
Models with mapped cooling Removing and installing, testing page 87-84.1
Task: controlling temperature flap and fresh air blower in line with temperature Emergency mode if it fails: outside temperature sensor -G17- performs task Testing: by self-diagnosis Replacing: - Remove glove box. Body Fitting Work; Repair Group 70; Removing and installing dash panel - Turn temperature sensor through 90 and pull out. - When installing, moisten rubber seal with oil. 1 Operates fresh and recirculated air flap at the same time Testing: by self-diagnosis Replacing page 87-80 Setting: Perform function 04 Basic setting page 87-61
# 1 S ` t s Y 4 #p "! 1 I " 2 " h I 2 q a i g r f # " 3 ) A #5 1Y S5 #I " 1 S I `a TQ Y Y 2 "B ## # 11 " " ## Q " & " Q S 0 % & bU 2 S c1 I BX 2 1 v ) w1 u % S & 2 % #1 1 S2 " 2 P 1 I `B t1 s2 Y0 4 #p& "!# )1 10 ! I! " 0 "# 2@ "" hQ I 2" PP A qQ a i# g5 r fB #3 "3 36 )(8 !$D # 11 S4 #1 " 1# S3 E I" # # " 2 5 `R 8W Y6 Y!PF 2('$!2C'$! "PSP'$ #P'! !)(9 1!(#! W `() #!5 Y(!7 "( &1' " " # 1 # " & 0P#P! %!7 0 % )!$! B b(V' b"C C'!!! d'QP' c$!!H D1)!'' !!G$ T!! c!'( R 2!!'P ('C2 " C4 d#P''C!!' eC G!)2!!! G"
T T T
------------
------------
87
15 Air
13
Air Conditioning
17
T T
OCTAVIA
G 1 @ 2 1 1 @ 1 2 2 1 0 0 3 G P 1 0 b 1 ` C Y 4 4 i " p4 # 4 %4 3 U U g h "U e " F 7 S E E 99 B4 2U 5 2 3 G5 1 1 d5 c a c i ' # %" " % g 4 ! ' S "" c E g % $ % ' F c S E f U $ $ A ' c S 5 FA E55 G G 1 25 1 0v 1 @ 0 0 B 2 1 4 3 5 $ ' G F d I E X G 0 2 1 2 ` 0 1 b" S c A W B8 2d " B' 2' 3 @ A 0 F4 Sc EE E' )' 4 13 2% BU g f BE 2 C 0 Qe A' 9 F X f $ #3 $ A " $ ` (3 3V (F x4 y4 w e ' 0 3 G Sh ) 2 1% 2U B3 T A v$ 2 B C 2I C 1 e 3 52 Qa A 22 1 1g 1) 01 G @ t) 3 YE cB EB 1u PI 2 `` 22 1 2Q 1F 02 @A CU 2 1 4U 0 3Q 3 Uf A 6 54 A3 A G FA b 2E 1 B$ CF c 01 TTB DS U AT1 ! " P% P @ 1 Q A(3 1AA8U Ud3 20 1A ` 4AA 4 3Y Q 1 UH U4U ) U P4 UA2 14 14 151T 38 525 BR 2X 152 2 11 0D 4E4 TS 342 35' rA q8 533 5A UUQ sA U1 5 0 1 i1 ' !W p #P 32 5# %5(3 3P AA23 3A f7 0 9 3" U$ B %@3 3 A P5 7A A0 AIA 4 45 e4AT '0 &" 5
1 18 3 0 1 Removing and installing page Only Removing and installing page unit and ture sensor sensor ponent and passenger side page unit to panel temperature are a single dismantled 07 page setting Air Conditioning K Installation is Unplug sor. 8 Air to Removing and installing page 7 4 1 Removing and page E Pay attention to installation position page plete Removing and installing page Removing and installing Fig. page air and delivery air in line outlet temperature mode it operation assumed value temperature page and take out in t reverse order. setting testing
------------ 87-77 ------------
OCTAVIA
Removing and installing Body Fitting Work; Repair Group 70; moving and installing panel
87
B $ h H H # TR "9 " $ R I " % 7 C $ " 7 9 7 $ R WE 2 U # " 7 C B C & 7 I C 7 7 C I P 2 2 !9 ! 1 H& "% B E $ C B " $ & 7 9 F 8 D G7 4 @ ! # $ " ) $ & $ ( d g f e $ " b a b & P cC C T $ C Y H H$ T 72 E% T $R 7 C 7 $ " $ C " E I 6` 27 29 2 U ( P 5AB 5 V HR #66 "H0i Ep T $ E ) $ $ $ & 7 " C SH66 T' " X H6 H C7 "" C'6'55 I$ 75A $0 "c 7 7 9" $ R & E B 9 R " C C " 6% PQ35 W95''56 V " $ $ % R C W ! # $ " $ U ( ! 0$ TH "HQ 7$ $B 7 # $ C R " 9I $ % R " 9 $ " % # $ " C $ 2% 5" ( S # "@ 7H C9 B60 & 7 C 7 7 C I 7 C I 2 P 2 !5& ! 1 H" "60% C'A B0 "0 $ $ 9H BH9 EH9 $'@ & 7 A9Q59 96H F( @ 8 D5H0 G" 4 2 ! # " $ & % $ % $ ) ( " 5$ R '66555Q''5' H6'Q5'9 99 5H6 6Q 9 50 ''9 5 3 9 95Q5''Q 5669
Edition 08.98 S00.5102.51.20
87
Air Conditioning
K-
OCTAVIA
l d d q r m j d } m r m j k x } m q d k s m j s m s | | { z E @ 1 E @ E 1 a E @ E 3 1 9 E w B t d s k d q l m d k j i d d d dr er r v s v s v s nhg q w s q v x v r u uq y y wmh vahgg r gunp s7Pngn x~ whyn qgyu vg7v vPghg x v C w v x s y p un Y Y boghg 2 1 E 1 1 V b @ C 1 9 1 E 1 7 Uf Dt e dn c B 1 2 3q @ 1 1 C V E 1 3 C Q E @ E 7 D1 R 8 8 F Y 3 V 3 V 9 E Q E V 3 1 C B e D D f Y Y3 2 1 E 1 1 b V @ C 1 9 1 E 1 A5 1 3 4 3 A X dx c B gA 1 E 1 C e d c U B ` YV 2A b @PE 1E 9@ 13 E 1 1 4 3 3 @ 3 A1 1 E E 3 a Q 9 E a 7 7 2 1 E @ 9 @ Q E C @ E E @ C Q E 3 D B B 0Y 0 G YA 1B @ 9 1 3 T A 9u VA 3 Q E W4 XD Ru U I S 0 F 2uu 1A E3 @x 2 96u @ 3 C @ 9 3 3 1 1 3 1 4 D B 8 %3 %5 P 56i5 u767 $7A 77 F7 7u " #Y #u # &A7 )V (CF 'H A7P P7P57 !V5P 55 4P AP5P557 775P75655P56 7h PA A T7 51 Y A77 A 57 7 7 7
Notes: When the battery is re-connected, Before disconnecting the battery, determine the coding of radio set fitted with anti-theft coding. Disconnect earth strap of battery before performing any work on the electrical system. Warning! be - Perform coding of radio - Re-set time windows and -E87- are a f ng and disand cannot
------------
OCTAVIA
Air Conditioning
the
------------
87
r y x p e d r y y y r y r r t r y r t q r x q r vr u px p r x r y r y r ru y x w r r r ruuuuvv pu puu q s b a a c cvv a c Y a c i c g b a V fuu cuuvvv cuu d bu avvv a c c V g d T h @ 7 ( % Q 1 S R 0g "q &$t 7 S "uvuu " " " # I 4 5 9 Y 7% Q (p " & % " % " % " & Q P H uvu % 4 ) "P " 8 " & % " % 4 D @ 3 2e 0 " % " " % 7 & ( ! (2 $ " Y $ 5 " & % " % % 9 6 & U I 7 % "$ &0 F ( 8 " 7 " ( $$G $ 4% 4W$ " ( 4 4 3 ) % ! )`$ % ($$ X "$C 2e %g $5 $" $ $$ 40 5 4 0 " & % & 1` %0$'$ X ) (R "50 & e'0$ e `$ ``E `W "`G 2E $$ ! $ $$ $$2 #` 2''$F $ 'B '''''' A
------------
------------
87
Air Conditioning
K-
Notes:
Before disconnecting the battery, determine the coding of radio set fitted with anti-theft coding.
Disconnect earth strap of battery before performing any work on the electrical system.
Warning!
be so that they do not come into contact with any the of the motors).
motors, enare
the
OCTAVIA
3 Q Q & & ' ' ) @ @ ' ' E R ' B ' ` Y ) H E & @ H % F % U @ ' R ' E % R A 5 S 5 5 t 3 % @ ' H H E F R % F H % U F U % B 9 9 1 S 5 S a V @ ' @ ) @ ' S s 3@ Q Q & ' ' ) @ @ ' ' E F R ' B % @ @ ' U @ 9 `0' Y F ' R & VU )) @8E & '0@ ' % ' % E % F % E R ' ' % ' S 0% QR FX FB @8 % F R9 F ' U @ ' ' E R F % F 9% 9 c 5 & %r @U % E E H ' R V ' R ) @ @ ' ' E R 9H S0@ 5 h Q V ' F E F F % F H B h ` 5 F9BX & %% & 'U R8998B F8Q %8 ' R H B@ ' H E BB % F S SB9 SQ g% f &808 V89 %% FB88 @8X F9 @ ' ' ' ) @ @ ' ' E B 9S 9% S% 59 5 @ &@ %0H )B83B F3R FU '8B9 FB '8 % (9 ' % @ ' eF @ ' F % B U 5 S 5BB 5X0g8X 5 & )S @ HE 'X839 %U R' @R % H ) ' ' R ) @ @ ' % SR SU 5 5 c 8' b880Q88898 W 30Q QQ &9 '8q V '9 ) @ F F U ' % @ R S 1 a 3B88 QBX0 @B080989 '8eB %898i @B8 @09 'X UB ) Hp EX U9 % F E % Y9r89098 ` Q & %B %U V %U (X8 ' E F BF ' F ' S( Y 5 W Q% % FR %0B E9 'Q EQ @ H V U H % F 6 ' % B) U % ( 98X' 5 T 3F % )QX908 V0 @S 'XB %9 @ ' @ ' F U ' % B@ % ' BU ( U B 9% 9 SQB8B 5 1 S 8E & %R @9898009 FXB8 E9 F9 ) @ R8 F @ @ F R ) @ ' ( Sd 50 5 $' $88 4 Q' %F E9D980888 HBB '8B8 F9B E3 %9 ' ) @ B99 ' B39 6 D999 IU A99 GB089X 7 C9 PU8 5 $ & ' % 2B ' ) % ( ( 1 88 " ! #Q B 00X800 ' B00998 B R % R8 BB83 9800XBQ 8X98 88 0 X 8 B 888B
The positioning motor for the air flow flap also operates the fresh and recirculated air flap. Note: and air -----------------------
OCTAVIA
Air Conditioning
KKK-
87
3 $ A 2 @ 9 & ( " ) 5 " I H H P 6 # t s % ) @ & ) ( 7 1 " s # % ) 5 # ( " r # $ D I H E F B d % # ) ( ( q $ 9 2 " " d d f # i( 3# g p 9 4 h " d % % " C h " d d f # " % !! i g p 2R A( 4 h d S G T T ( " " d du f # i 3( g p 9% 4 h " "# & " !# d e ( ! %# # & " " ) ! !! # # ! # 5 c D E E I H H E ` b a W CR U! P C I H P V5 H R V P D U P4 D C H I H E S S Q B X T 3 2 $G A @!! 9 & 8 % )i!! !i ! " 7 & " 6 ) U ( ! T !S i " 5 !! 5 ' % F ) ! 3 3 "E 4 1 2%! 0 2 1 & ! ' # #!!% C (G # $ "! Y ' 5 ! ! % Y ( ' & #! ! ! G G $# "' ! #! # %#%! T!! SG !!! S ! !!G V! G % !
------------
------------
87
Air Conditioning
K-
K-
OCTAVIA
OCTAVIA
Air Conditioning
K-
87
and First of all, perform the following steps: Remove glove box, trim surround for dash panel insert and bottom part of dash panel on left. Body Fitting Work; Repair Group 70; Removing and installing dash panel - Remove centre console. Body Fitting Work; Repair Group 68; Removing and installing centre console - Remove centre part of dash panel. Body Fitting Work; Repair Group 70; Removing and installing dash panel Remove footwell vent page 80-15. Separate plug connection -1-. Use a screwdriver to carefully unclip operating rod -2- from lever -arrow A-. Unscrew bolts -3- attaching motor. Turn operating rod -2- and take it off from positioning motor -4-. Take out positioning motor. Installation is performed in the same way in the reverse order. Initiate basic setting function 04 page 87-61.
------------ 87-83 ------------
B U ' G 4 3 @ ) @ R G W @ ' S X h g c T ' 4 @ ' @ ) @ ) 4 ' W G @ 4 5 @ 2 2 7 9 ' 4 8 ) W @ ) 8 1 ( )b ') 45 3 @ W ' ) ' 0 ' ) 4 8 S 7 1 9 6 g U @9 4 8' G @ 4 ' 3 ) ' 4 ' @ ' 8 ' W 74 72 9 9 7 ' G 4 3 @ ) S g a g (9 ( ` 44 R8 @W 4' ' G @ 8 @ D ) 8 @ ) 4 ' W ) 98 7 9 A@ ( @ ) 4 ( 43 @1 'FA4 W@ 4 @ ' D ' 8 8 ' 8 8 D 8 2) 2 7D AW F2 & )F) '9 @8 ) @ ( ) 4 ' W G @ 4 5R @ @ 8 4 G @ ' 7 9 6' 7 FW 5 s u' r5 q v u w u w y u v u w r x2 x i t' ' G S X h g @ ) @ R G W @ ' 4 8 ' W 8 4 @ c2 T2 1 '6 ) ' ' ' 7 @ ) 4 (FFD `tB25F (6FA2 @5FF22 4F@ '9 DF) 4F2FA5F '2U @22F6 8UF 'F2 )2 'A6 3 8 95A2 75 F2F0 FA2 A b B' U U (F5 G2FAAW @4 Rp )5FF2 'UA 89 )2 ) ) G @ @ ) ) 3 98 9B c5 F4 6 6 G22 @62 @F2 R 1 7 b U (2F2 G4FA @3 49 '' 3622FF )I 'FF2 )FAA ) ) G @ 50 @ ) ) 3 5 28 9F5 c FFD 6 Y BI ( )t ) G ` @ 4 4 W ) 5 8 ' @ 2 9 a 1 V U U ' 4 4 3 ' @ ) ' @ @ ) W G R 3 W Xtt ( ' @ 4 3 4 G @ 8 4 @ @ 4 8 G @ ) 9 7 7 &' & C Ud '' 4U 36 'B ) 5 D 326F R2 )2 G @ PU 5 SB5 H2 QUF2 T25 E I 7 & B4 ( '4 @262 )0 ( 'A2F2 @2 4F5 3FB 45 ) 82 4 3 ) ) ' ) ' 0 2 9P 7B 1 68 A) A8 f FF ! %5 #U $A5 2FAAFe ! W 52F 52FA F2 F22F 25F UA AF5 5 2F Ff F 22 F 52 F2 82 "2 ) U2 "2 FFF
------------
------------
87
Air Conditioning
K-
tioner
OCTAVIA
A E b a e e t g B B A A V h A q b a A q C A R d b A b E C r g B A E b a V d C V C V C q b q e sA v C E V A Y V C b h C E V q V b E V S Q S B dV bb bU v A qT q b E h b C X V A d Uy U Si S F b A R A V h h r Bh v bV E bh C V A d v C E V q C XA `Fq b E V q q QX Q A A b D V q C b h A q A q Q i @ IQ B AX Vi AX Ah d b hh A a A A d XX C A V A X A b a A q QA A A b D C V q V C b h q A Q i i e f s V C b q b u A V A h Q i vUFX Cb byFg VTR Ch ha qXyU AIX VU q` A A A A V b q A A h d h A Ua UTh U iX G yY 7 6 ' % IbT BTTUx AA CUTUITTFTT Ah AX AFU h AI DU V A Xq C X A a XU V C b X h Qt iX Q 7U 6y 6 B A r gAT gD gTUTT vXXTT Aa Vq b' XA A V A V d h CFXX bFXU EF d C XU X QXTIX Q fTTX ty iX i s u p CU ATT V V C q E d a V q B AUTTyx VUT bg aU b E V hX b V V b h E V C D iX Q Q @C @UTTU P gAy Aa A C R aFh dX C bUU aFU C E V `3 XX XU eq WTTTF cTUy fUUy S Y Q @ A C E D B CT H A C A D G 2 7U 6y # 9x % 8 2I 7gyT 6IUI ( #XT #UI 4I 5X 4T % 3 # ' % 0 " $I 1 $ )I &X b X& T0 ) UU&FF TXT0 X UUT& U)U U T) XITT T TFFI)Fx !V `FUw
----------------------------------
OCTAVIA
Air Conditioning
K-
87
D b F G f f i e X S S D D U T D Y F G D Y H D Q F D F b H X S D b F G U Q H U H U H Y F Y f e y H b U T D U H F T H b U Y U F b U V V S QU FU F y D Y Y F b T F H I U D Pa P F D D U T T D SD y FI b F H U D Q y H b U Y H IF RY F b U Y Y D I V V D D F E U Y H F T Y D Y V ` D XD S UG DQ DRWI QWT FT TD D G D D Q H H F H G II F D I D F G D Y P d D D F E H U Y U H F T D G D Y V ` p p i F U H F D D U D D T V yPRI UI D D D D Q D HEP FaRXW U HPWPaX TG YIIP DcI YP D U F Y D T PG w x `RPWR aT CW B 1 v cF D HYa DWWPWu DP D TPc Ec IY I` I I SWWWWP UI D H D G U H F T F U VV V CWW B B c` SRII DPRIPWW HII DPI ET Ua FI b Q H D U D I U Q T VcWWI pR i ` ` V q HP DX UWW U H Y Y b Q G U h cY XT S DWu b F G D U H U H F D Y H E I fWPWWP g` e) eWaa d V cD bt H F D D F UT QT HPPWcc TPI HI FcI HP GRI FI D D EP II IP ` V ` ` W1 XPF SIWR HIY DT UPWPPX TqPWW DIW DIP QPI FI TPP DP Ga D Q H ID H F H G F D I E D VPWPa RF W` 4 CP Ba ' @u ) 9 7W 4WW ' ' 1 ) 3 & 8a 5c 6c 5c ( ! "P %X $X #0 W2WRu A RIRR Is PIAr !s PWP P PX PIWP WA IX P P PI0 a0
-----------------------
------------
87
Air Conditioning
The
he
OCTAVIA
s 8 30 ' # ' 2 # 1 ` 3 ( # % % cC 7& a 3 c w s& 8 (1 #S 1S 3' 1h 3p (& ## %b &1 %( 0@ aD AQ A1 B1 CS C2 Q D x& yA 3C 3 ( b ' V ' cU wg a sT 6G 10A 3#D (P #b &f # V V 3 %% ( # # 2 1 (v0A #0H 101 30c %9' %$$B 093 a1 Cd Gr A C H G B B A C D pB @ 3$( t$$3 5 cQD s) 3H(Fq ($$%E1FY% buC$$00 'W0RY8 V%#D$$9 '$D3$8% #$8A%R '8I% 28$10E #T%9 13V 'SY$%9 ##RE6 `c$ 1'7 30`$4 (qG V24 #( %D0X %2e &' ' # & % 0iE 0A 0 av0Y1G a$A ) " !
Edition 03.01 S00.5102.54.20
OCTAVIA
and
Air Conditioning
seal to
seal to
seal to
------------
lines
lines
------------
87
87
Air Conditioning
OCTAVIA
8 9
4 5 ' ) " 0' 3 !' )# 2 1( " ! %# % !&$ ) & 0' $$% $
Separating and assembling evaporator housing Fig. 1 10 Air When installing, ensure clearance to moving parts Fig. 6 11 Removing and installing page 8778, Fig. 2 Screwed on After replacing, fill system complete with fresh coolant Removing and installing page 8740 1 Screwed on and attached with tensioning strap -2 Must rest firmly against evaporator housing Models from 03.01 Removing and installing, testing page 87-84.2
Edition 03.01 S00.5102.54.20
E & $ ( 6 $ 1 & $ ( 1 6 0 5 3 ' % D # # # # '# $ ( $ $ 1 3 ' 1 $ 5 5 1 ( $ 6 % y 7 8 7 # $ )# % 9 v t u w x q S b H T H W H Q W Y Y ` S W q W X c c YY H Y `T d$ H H W Q W T X q S S T H c a c c qq S9F b H T9 H W H Q W Y Y ` S b H Y X b H c c a p Y$ H9 s' d d% Q T W q S S H T S X Y XS Y T P1 r9 c I" 9% x4@% 4)@4)4 %2 @ ) ! i e Y S Y Y b Ugc SU Yg YP S b H W Y H Q Y ` W S X T H Ph cT a a V a F 9 9 ' ( 1 5 6 ' $ 6 5 3 1 7 EX 8 D # 9H BP 'Y Cb 5R0 'P C) 17 5 $ ( ( $ A @a ( $ 6 ' $ %G #PR #P # " 9WRP 3)XU 'R%PRP 6X 5X 39 1IPX 1 ' $ ( 1 $ $UP)RP & ' $ ' %S #XP 8 7X4UR # # 20 # 4d # 49 PX !X P $ fR%RIR Q4P Y 4%Rd $ 7 T %@)% %P %4 %X %%% X % d 2RgRP4P @X
Notes: The Note: The to
------------ 87-87 ------------
OCTAVIA
Air Conditioning
K K K
87
87
Air Conditioning
Note:
No gasket is fitted to the bottom part of the evaporator (to allow the condensation to flow off).
K ig. -
K ig.
Notes:
R Q P $ $ 6 3 " 3 $ 3 3 $ D D 3 $ & " 2 C $ E" D# D 9 0 3 3 0 " % % " 6 & ( 2 B $ &H D % II I F# G " 6 3 9 $ $ 0 " '& ' 5@ " 6 0 0 0 $ $" &$ &A 7 2 8F&)%&11) $ 4 30 "17& #" $&0 "1& " 0 $ " $ # " ! 0 &3 2 ! 2 (% )! )')& %)% '1 ' ')&& ) & # & &&% 3 1@ %
OCTAVIA
to to Install the wiring loom -A- so that it cannot come into contact with any moving parts (e.g. levers -B- of positioning motors). Route wiring loom so that it does not rattle.
Edition 08.98 S00.5102.51.20
@ ) ( & ( G ) & # ) # " ) # ) & ! ) & 1 & & 1 ) D % 4 ) 4 ) # # ( & # 0 0 % 0 B 4 & ) # @ " & ( & 2 & 6 % ) I1 Q4 i&) TU6 f% d4 T%A f# f3 e# d# R1 d1 c0 YS) b `g1# a) hS)0 h&" hW) S)( & ('') @ " & ( # " & & 0 7 )$ 7 &8 1 & 4 # " " # " & ) & & & !# % % 6 &% 3 & 4 ( 8 " ) ) 2 ( ) & & 0 7 % 0 '1 6 )$8 & 1'" ) & # " ) 4 " & 1 & & " !!2 0'!! % 3# &''!!'! 1''!$ )'! "" 2" )'$ "" # ) # & ( # " 0 % I#! V"9!'55'5 QSS&$'A'!555$ Q8 T)" Q"( RF'555!!'! QE''!!' UC!! U) U&!$'! W&% Y"! X)& P$$!'5'' `W1!''!'!! H&!''A S&&
Edition 08.98 S00.5102.51.20
Notes:
OCTAVIA
All
Air Conditioning
Low-pressure side For extracting, filling and measuring Always fit on cap with seal
Removing and installing page 87-30 Replace the receiver each time the refrigerant circuit is opened
------------
------------
87
87
Air Conditioning
OCTAVIA
4 - Air conditioning pressure switch -F129or high-pressure sender -G65 -G65- is fitted in place of -F129- on models from Model Year 99 with 1.6ltr./74 kW engine -G65- is fitted to all models as of Model Year 2000 -F129- (4-pin plug connection), operation, removing and installing, testing page 87-24
------------
------------
3 - Extraction and filling valve* High-pressure side For extracting, filling and measuring Always screw on cap with seal
-G65- (3-pin plug connection), operation page 87-11, removing and installing, testing page 87-25
5 - Expansion valve* Removing and installing heat insulation page 87-26 Detaching and attaching refrigerant lines page 87-26 Removing and installing page 87-26
6 - Dust and pollen filter Below plenum chamber cover Removing and installing page 80-16
Edition 07.99 S00.5102.53.20
OCTAVIA
7 - Condensation drain valve Inspecting, removing and installing page 87-27 8 - Coolant temperature warning switch (+119 C) -F14 In refrigerant circuit -F14- switches magnetic clutch -N25off if coolant temperature too high (off at 119 C, on at 112 C) 1.6-ltr./74 kW Model Year 98 and all models Model Year 99 9 - Radiator fan control unit -J293 Bolted on below battery rack The magnetic clutch -N25- of the compressor is also operated through this control unit 10 - Ambient temperature sensor -G17 Task: operating temperature flap and fresh air blower as a function of the ambient temperature Emergency mode in the event of failure: fresh air intake duct temperature sensor -G89- performs this task. If both sensors are faulty, air conditioning continues operating with assumed value of +10 C; no recirculated air mode is possible; readout in display of operating and display unit -E87-: -. Testing: by self-diagnosis Bolted to longitudinal member at front left 11 - Pressure relief valve* O-ring seal: 8.6 mm; 1.8 mm Tightening torque: 10 Nm Testing page 87-28 12 - Oil drain plug* O-ring seal: 8.8 mm; 1.5 mm Tightening torque: 15 Nm
Air Conditioning
87
Notes: For draining refrigerant oil: Remove compressor. Remove oil drain plug. Rotate compressor at clutch plate of magnetic clutch in order to accelerate the flowing out of the oil.
13 - Compressor* Removing and installing compressor bracket Engine, Mechanical Components Detaching and attaching compressor at bracket page 87-28 Detaching and attaching refrigerant lines page 87-29 Removing and installing compressor page 87-29
Notes:
Removing and installing ribbed V-belt. Engine, Mechanical Components Mark direction of running of ribbed V-belt before removing; if the belt is fitted on to run in the opposite direction, it may be damaged. The piston stroke of the compressor is variable and depends on the refrigerant capacity requested. If a new compressor is installed or if fresh refrigerant oil is poured into the compressor (e.g. after cleaning refrigerant circuit and emptying compressor through oil drain plug), the compressor should be rotated by hand approx. 10 revolutions after being installed (in order to avoid compressor damage when first operated). 14 - Magnetic clutch -N25 Servicing page 87-32 15 - Condenser* Removing and installing page 87-31
------------
------------