DSR 2012
DSR 2012
All rights reserved. No part of this publication, either in English or in Hindi, may be reproduced in any form or by any means, electronic or mechanical including photocopy, recording or any information storage and retrieval system, without permission, in writing, from the Director General, CPWD, New Delhi. This Delhi Schedule of Rates 2012 is prepared for the use of CPWD. However, this may be used by other Govt. departments, PSUs, private bodies & individuals also at their own discretion. CPWD shall not be responsible for any ambiguity, discrepancy, dispute or financial loss, arising directly or indirectly by using or following items of DSR by such Govt./Private bodies or individuals.
A GOVERNMENT OF INDIA PUBLICATION Published by DIRECTOR GENERAL CPWD, NIRMAN BHAWAN, NEW DELHI-110 011 Printed & Marketed by JAIN BOOK AGENCY Authorised Dealers of Govt. Publications C-9, Connaught Place, New Delhi-110001 Phone : 44556677 Fax : 41513850 E-mail : [email protected] Website : www.jainbookagency.com Distributed by JBA DISTRIBUTORS N-67, First Floor, Munshiram Building, Connaught Place, New Delhi-110001 Phones : 23354824, 43528601 E-mail : [email protected] Website : www.jba.in JAIN BOOK AGENCY (SOUTHEND) 1, Aurobindo Place Market, Hauz Khas, New Delhi-110016 Phone : 26567066, 26566113,41755666 E-mail : [email protected] Website : www.jainbookagency.com JAIN BOOK AGENCY (GREATER NOIDA) 11 Jagat farm Complex Gama Sector Market Near OBC Bank Greater Noida Phone : 0120- 4206655, 4206657 JAIN BOOK AGENCY (CENTRAL) 5061/1, Sant Nagar, Karol Bagh, New Delhi - 110005 Phone : 44332211
JAIN BOOK AGENCY (GURGAON) 12, Central Plaza Mall, Sector 53, Golf Course Road, Gurgaon 122002, Haryana Phone : 0124- 4143020, 4142665 Mobile 9810666810
FOREWORD
Delhi Schedule of Rates, being published by C.P.W.D. from time to time, is a very comprehensive document and useful in execution of works. Apart from C.P.W.D., this Schedule of Rates is used as a guide by a number of departments, public sector undertakings, private sector builders and architects etc. The Central Public Works Department Schedule of Rates was first compiled in the year 1931, followed by a number of revisions from time to time in order to bring it in line with the prevailing technology and market rates. The Delhi Schedule of Rates were revised many times in the subsequent years viz. 1977, 1981, 1985, 1989, 1993, 1997, 2002, 2007 & 2010 (Reprint ). The last Delhi Schedule of Rates was printed in 2007. The prices of labour and materials have registered substantial increase since then. Besides the cost, there has been spurt of new construction materials and introduction of Green Building concepts, new technology etc. This has necessitated revision of existing DSR 2007 to include the above changes. Although this DSR contains most of the items of DSR 2007, the nomenclature of all existing items has been reviewed & updated whenever found necessary. Items which are either obsolete or are not in use have been deleted. Similar items have been clubbed to facilitate convenience of use. Several new items, based on new materials and new technologies in the construction sector, being adopted in CPWD works, have also been included in this document. I wish to place on record the technical input and effective coordination on the part of Shri P.K.Gupta, ADG(TD) and the efforts put in by Shri A.K. Sharma, CE(CSQ), Shri S.P. Chaudhary,SE(TAS) and his team of officers in TAS unit in finalising the DSR in a record time. I am sure that this Schedule of Rates will be quite useful to all concerned in the Building industry in general and CPWD in particular.
New Delhi
PREFACE
1. Delhi Schedule of Rates 2012 includes the existing items of DSR 2007, with deletion of few obsolete items, merger of similar items and addition of new items in line with emerging trends in construction technology. Delhi Schedule of Rates 2012 is based on the prevailing market rates of materials in Delhi between April 2011 to Sept. 2011. The labour rates adopted are as per minimum wages issued by Govt. of Delhi w.e.f. 1/4/2011. The Cost Index based on Delhi Plinth Area Rates - 2007 as base 100 as on 1/10/2007, as corresponds to DSR 2012, is 149. Many new items & sub items have been introduced in DSR 2012. Items related to Green building concepts have also been introduced. Following are the salient features of DSR 2012 (a) DSR 2012 is a bilingual (Hindi version will follow ). (b) The nomenclatures of items for cement & bitumen coefficient have been abbreviated for convenience of users. (c) New sub head for Rain Water Harvesting & Tubewells has been introduced. (d) New sub head for Conservation of Heritage Buildings has also been added. (e) This DSR 2012 should be read alongwith CPWD Specifications 2009 Vol. I & II with upto date Correction Slips. (f) New Material Codes have been assigned for the new materials incorporated. (g) The basic materials incorporated in this DSR 2012 are considered to be conforming to BIS Standards/CPWD Specifications/ Materials of good quality generally available in the market. (h) The class designations of bricks have been modified in conformity with relevant IS codes. (i) Grades of bitumen have been modified based on viscosity grade viz VG-10, VG-20 etc. 6. Sub head wise salient modifications and additions are as under :6.1 Earth Work :- Items of fly ash as filling material has been added. 6.2 Concrete work : (a) Finishing component to Precast CC members has been deleted. (b) RMC plain concrete with and without fly ash has been introduced as new items. 6.3 RCC Work :(a) Finishing component with cement plaster has been removed from items of precast RCC. (b) The quantity of cement for the items of Design Mixes has been indicated as a guiding reference only for rate estimation & justification etc. The exact quantity of cement to be used shall be worked out as per actual design & any excess/ less quantity of cement is payable/ recoverable through separate item. (c) Many new items have been added viz. stainless steel plate for expansion joint, design mix concrete using fly ash, concrete curing compound and reinforcement couplers for mechanical splices of bars.
2.
3. 4. 5.
6.4 Brick Work : (a) FPS bricks have been renamed as common burnt clay (non modular ) bricks. (b) The class designations of all bricks & tiles have been changed as per IS code. (c) Individual items for brick work above floor V levels have been merged in single item. (d) Items for super structure have been created as sub group for exposed brick. (e) Half brick masonry with fly ash bricks has been introduced. 6.5 Stone Work :(a) Items of random Rubble & coursed Rubble in super structure have been modified to have independent items without relating to foundation items. (b) Item nos. 7.8, 7.13 & 7.14 have also been modified with additional sub items. 6.6 Wood & PVC Work :(a) Fixing of Frames with dash fasteners is added. (b) Few separate items have been merged as sub items under one main item. (c) "M.S. pressed butt hinge bright finished" is specified in place of black enameled M.S. butthinges. (d) Items of Sheesham wood for shutter has been added. (e) Stainless steel wire gauge have been added as new item. (f) Item nos. 9.48 & 9.49 have been specified with priming coat. (g) Item nos. 9.123 & 9.124 of PVC frame & shutter have been modified with single extruded sections. (h) Many new items have been added viz. plain lining with ply, steel frame work for partitions, fire resistant doors & frames, PVC door/frame & uPVC windows. 6.7 Steel Work :(a) Fixing of windows & door frames with dash fasteners is added. (b) New items of stainless steel railing & stainless steel wire gauge have been introduced. 6.8 Flooring :(a) Skirting with kota stone is modified to 20 mm instead of 25 mm. (b) Vitrified flooring with cement based adhesive base is made complete item, alongwith other new items of skirting & joint grouting. (c) New items of crazy tile flooring and Turf Paver have been introduced. 6.9 Roofing : (a) New sub items have been added under main item of false ceiling viz. gypsum fire rated board, gypsum moisture resistant board & fully perforated gypsum plaster board. (b) Galvanized coating on sections of false ceiling have been modified to 120 gms/sqm. considering inside use & market availability. (c) New items have been introduced for G.I. metal ceiling lay - in tiles, (plain & perforated) and gypsum (plain & perforated). (d) New items for calcium silicate tile in false ceiling, G.I. clips- in metal ceiling (plain & perforated) have also been incorporated. (e) Similarly, new items of heat resistant tile on terrace, roof insulation with rigid polyurethane foam and thermal insulation with resin bonded fibre glass wool on wall have been added.
6.10 Finishing :(a) Item no. 13.51 with white lead has been modified with silicone acrylic emulsion based water thinnable sealer. (b) Items of forming groove in washed stone grit plaster is modified to be provided with Aluminium channels. (c) New items of VOC paint i/c primers have been added. (d) New item of cement based putty has been added. 6.11 Repairs to Building : Item nos. 14.73 & 14.74 have been shifted to this sub head from steel work. 6.12 Dismantling & Demolishing :(a) Items of demolishing CC/RCC have been modified. (b) New item of disposal of dismantled material has been introduced. 6.13 Road work :(a) Grades of bitumen have been corrected based on viscosity grades. (b) Item no. 16.31 has been modified to include bitumen emulsion (medium setting) & to include WMM also. (c) Item nos. 16.54 to 16.57 have been modified to bring at par with prevailing practice. (d) Many new items have been added to this sub head. This includes items of granular sub base having different CBR values, WMM, dry lean concrete sub base, item of temporary barricading, dismantling & relaying kerb stones/ paver blocks. 6.14 Sanitary Installations :(a) New items have been introduced for wall mounting W.C. Pan, waterless urinal & sensor based urinal. 6.15 Water supply :(a) New items of sensor based pillar cock has been introduced. 6.16 Drainage :(a) Nomenclature of items has been updated in respect of change in nomenclature of bricks. 6.17 Pile Work :(a) New item of pile integrity test has been added. (b) The design mix grade of concrete of pile has been modified to M-25 in place of M-35. 6.18 Aluminium Work :(a) Item no. 21.1, 21.7 & 21.14 have been modified in respect of fixing with dash fasteners instead of rawl plug etc. (b) New items have been introduced for Aluminium grills & toughened glass door shutters. 6.19 Horticulture & landscaping :(a) Items no. 23.10, 23.19 & 23.16 have been modified. (b) New items have been added covering items viz. tree guard, preparation of mounds, and cement concrete pots. 6.20 Rain Water Harvesting & Tubewells :This is new sub head which incorporates various new items of rain water harvesting & tubewells for different dia.
6.21 Conservation of Heritage buildings :This is new sub head created alongwith new items of cleaning & preservation of heritage buildings. 7. A lot of effort has gone into the preparation of this Schedule of Rates. I convey my deep appreciation and sincere thanks to Shri A.K.Sharma, CE(CSQ), Shri S.P. Chaudhary,SE(TAS), Shri R.K. Saraswat, EE(TAS), Shri Kamata Prasad, EE(TAS), Shri R.K. Vashisth, AE, Shri A.K. Upadhyay, AE, Shri R.K.Goel, JE, Shri A.K. Singh, JE, Shri K. Ratha, JE, Shri R. Kumar, D-Man, Shri B. Singh, D-Man and other staff of TAS unit for sincere efforts made in the preparation of this document in such a short time. Thanks are also due to all the members of drafting committee and other field officers/ staffs who have contributed actively in finalising this DSR. I also express my sincere thanks to Shri V.J. Reddy EE(P), Hydrabad Central Circle - II, who has contributed & helped in finalising the DSR in addition to his routine duties. 8. Due care has been taken to print the Schedule of Rates as correctly as possible. It is, however, possible that some errors might have crept in. In case, any error or omission is noticed, it may be brought to the notice of the Superintending Engineer (TAS), CPWD, Room no. 418, 'A' Nirman Bhawan, New Delhi - 110011. In case of any discrepancy between English and Hindi versions, the English version shall be held valid. Suggestions for improvement are welcome.
9.
(a) Ready mixed design mix concrete for R.C.C. using fly ash 5.40 (a) (b) (c) (d) (e) Brick work with clay fly ash bricks Brick work with fly ash lime (FALG) bricks Brick work with extruded burnt fly ash clay sewer bricks Brick work with autoclaved aerated cement blocks Brick work with mechanised autoclaved fly ash bricks 6.32 6.34 6.37 6.38 6.42 9.2 9.6,9.10 & 9.31 9.38 11.15 11.44 11.45 12.16 & 12.17 12.20 12.34,12.35 & 12.57 12.36 12.55 12.56 12.57
5 Wood Work
(a) Laminated Veneer Lumber frames of doors/ windows (b) Laminated Veneer Lumber door shutters (c) Providing and fixing 4mm thick coir veneer board (a) Crazy marble stone flooring (b) Crazy ceramic tiles flooring (c) Turf Paver (a) Mud phaska (b) Pressed clay tiles on roof (c) Under deck insulation (thermal insulation with Resin bonded fibre glass wool) (d) Thermal insulation of roofing with exposed polystyrene (e) Heat resistant tile on roof (f) Roof insulation with Rigid Polyurethene foam (g) Wall insulation with Resin Bonded Fibre glass wool
6 Flooring
7 Roofing
8 Finishing
(a) Distempering with 1st quality Acrylic distemper having low VOC 13.81 (b) Wall painting with Acrylic emulsion paint having low VOC 13.82
(c) Wall painting with Premium Acrylic emulsion paint having low VOC (d) Painting with synthetic emulsion paint having low VOC (e) Applying priming coat on wood /steel/wall with primer having low VOC 9 Repairs to Buildings 10 Road Work (a) Mud Mortar made with local clay good earth (a) Preparation of sub base of road pavement with fly ash stabilised soil (b) Precast lime fly ash concrete blocks (a) Vitreous China water less urinals (b) Sensor operated urinals
11 Sanitary Installations
13 Water Supply (a) Battery based, sensor based, pillar cock. 14 Water Proofing (a) Brick coba Treatment 15 Aluminium Work 16 Rain Water Harvesting (a) Double glazed aluminium windows (a) Rain Water Harvesting with PVC pipe and recharge pits etc.
C O N T E N T S
SH. No. NAME OF SUB-HEAD BASIC RATES 0.1 0.2 0.3 0.4 Hire Charges of Plants Labour Materials Carriage Codes SUB -HEADS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. (New) 25. (New) Carriage of Materials Earth Work Mortars Concrete Work Reinforced Cement Concrete Brick Work Stone Work Marble & Granite Work Wood and PVC Work Steel Work Flooring Roofing Finishing Repairs to Building Dismantling & Demolishing Road Work Sanitary Installations Water Supply Drainage Pile Work Aluminium Work Water Proofing Horticulture & Landscaping Rain Water Harvesting & Tubewells Conservation of Heritage Buildings CEMENT CONSUMPTION STATEMENT BITUMEN CONSUMPTION STATEMENT 59 69 77 81 91 105 115 125 131 171 181 195 217 231 245 255 277 299 329 343 351 359 369 377 383 389 425 3 6 8 56 PAGE No.
BASIC RATES
Code No. 0037 0038 0039 0040 0041 0042 0043 0045 0046 0047 0048
Description Mobile crane Tractor with ripper attachment Tractor with trolley Air compressor 250 cfm with two leads for pneumatic cutters/ hammers Joint cutting machine with 2-3 blades C.C. batch mix plant Road sweeper Slip form paver with sensor Water tanker 5000 Ltr. Capacity Concrete joint cutting machine Texturing machine Note :- Above hire - charges include cost of services of operating staff and supply of lubricating oil. NEW CODES
Unit day day day day day day day day day day day
Rate 6,500.00 1,350.00 1,350.00 1,800.00 900.00 10,000.00 550.00 13,000.00 1,000.00 900.00 925.00
0049 0050 0051 0052 0053 0054 0055 0056 0057 0058 0059 0060 0061 0062 0063 0064 0065 0066 0068
Dozer D-80-A 12 Motor Grader 3.35 metre blade Hydraulic Excavator of 1 cum bucket Front end loader 1 cum bucket capacity (incl POL) Tipper -5 Cum Vibratory roller 8 to 10 tonne Smooth Wheeled Roller 8 to 10 tonne Tandem Road Roller Water Tanker 5 to 6 KL capacity Air compressor Wet Mix Plant 60 TPH Mechanical Broom Hydraulic Emulsion Pressure Distributor @ 1750 sqm per hour Hot mix Plant -120 TPH capacity Hot mix Plant 100 TPH Capacity Paver finisher Hydrostatic with sensor control 100 TPH Paver finisher Mechanical 100 TPH Batching and Mixing Plant @ 75 cum per hour Concrete Paver finisher with 40 HP Motor and sensor
hour hour hour hour tonne km hour hour hour hour hour hour hour hour hour hour hour hour hour hour
3,800.00 2,450.00 1,300.00 800.00 3.00 1,550.00 460.00 1,150.00 150.00 325.00 1,200.00 360.00 800.00 23,700.00 17,500.00 2,700.00 1,000.00 2,500.00 2,900.00
Description Generator 250 KVA Generator 100 KVA/125 KVA Truck 5.5 cum/ 10 tonnes Road sweeper (Mechamical Broom) @ 1250 sqm per hour Drum Type HMP of 60-90 TPH capacity @ 75 tonne per hour actual output Hire and running charges of drill machine up to 400 mm dia (including cost of mobile oil, diesel consumption in ordinary soil and operator) Note :- Above hire - charges (from item code 0049 to 0080) include cost of services of operating staff, supply of lubricating oil and diesel also.
Description Mason (average) Carpenter (average) Operator (Pile/Special machine ) Skilled torch operator for laying tack Note :- * These rates are average of 1 st class and 2 nd class categories. This is for use in the analysis of rate only.
Code No. 0297 0298 0302 0304 0305 0308 0309 0310 0312 0313 0314 0316 0317 0318 0322 0324 0325 0326 0328 0332 0336 0339 0341 0346 0347 0348 0362 0364 0365 0367 0368
Description Stone Aggregate (single size) : 10 mm nominal size Stone Aggregate (single size) : 06 mm nominal size Safeda ballies 125 mm diameter Bajri Bamboo 25 mm dia 2.5 metre long Bhusa Paving bitumen of grade VG-10 of approved quality Bitumen emulsion Bitumen grade PMB - 40 Blown type petroleum bitumen of penetration 85/25 of approved quality Bitumen hot sealing compound : grade A Bitumen solution primer of approved quality premoulded joint filler 12 mm thick Bitumen felt fibre base (vegetable or animal): Type 2 grade 1 Bitumen felt : Type 3 grade 1 Coal Tar Blasting powder Blasting fuse ( fuse wire ) White face insulating board : 12 mm thick Natural colour insulating board : 12 mm thick Flame retardant face inslulating board : 12 mm thick Flame retardant face inslulating, impregnated fibre board 12 mm thick Flat pressed 3 layer particle board (medium density) Grade 1.12 mm thick Extra for veneered particle board with : Teak veneering on one side and commercial veneering on other side Extra for veneered particle board with Commercial veneering on both sides Extra for veneered particle board with Teak veneering both sides Brick bats Wire brush Soft brush Portland Cement White cement
Unit cum cum metre cum score quintal tonne tonne tonne tonne kilogram litre sqm sqm sqm litre kilogram each sqm sqm sqm sqm sqm sqm sqm sqm cum each each tonne tonne
Rate 1,050.00 1,100.00 37.00 900.00 300.00 375.00 37,000.00 28,500.00 41,400.00 37,000.00 26.00 40.00 350.00 55.00 50.00 25.00 35.00 15.00 360.00 270.00 315.00 350.00 325.00 235.00 155.00 455.00 325.00 20.00 18.00 5,000.00 12,000.00
Code No. 0370 0373 0378 0379 0380 0381 0382 0383 0384 0385 0386 0387 0388 0389 0390 0391 0392 0393 0394 0400 0401 0402 0403 0404 0405 0406 0408 0409 0410 0411 0412
Description Coal (steam) Cramp Gun metal 25x6x300 mm Brass butt hinges (light /ordinary type ) : 125x70x4 mm Brass butt hinges(light /ordinary type) : 100x70x4 mm Brass butt hinges (light /ordinary type ) : 75x40x2.5 mm Brass butt hinges (light /ordinary type) : 50x40x2.5 mm Brass butt hinges (heavy type) : 125x85x5.5 mm (0.70 kg) Brass butt hinges (heavy type) : 100x85x5.5 mm (0.56 kg) Brass butt hinges (heavy type) : 75x65x4.0 mm (0.20 kg) Brass parliamentary hinges 150x125x27x5 mm Brass parliamentary hinges 125x125x27x5 mm Brass parliamentary hinges 100x125x27x5 mm Brass parliamentary hinges 75x100x20x3.2 mm Brass single acting spring hinges 150 mm Brass single acting spring hinges 125 mm Brass single acting spring hinges 100 mm Brass double acting spring hinges 150 mm Brass double acting spring hinges 125 mm Brass double acting spring hinges 100 mm Brass tower bolt (barrel type ) 250 x 10 mm Brass tower bolt (barrel type ) 200x 10 mm Brass tower bolt (barrel type) 150 x 10 mm Brass tower bolt (barrel type) 100 x 10 mm Brass flush bolt 250 mm Brass flush bolt 150 mm Brass flush bolt 100 mm Brass handles 125 mm with plate 175x32 mm Brass handles 100 mm with plate 150x32 mm Brass handles 75 mm with plate 125x32 mm Brass door latch 300x16x5 mm (0.380 kg) Brass door latch 250x16x5 mm (0.350 kg)
Unit quintal each 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each each each each each each each each each each each each each each each each each each
Rate 400.00 70.00 800.00 650.00 400.00 175.00 2,900.00 2,600.00 900.00 2,600.00 2,300.00 2,000.00 1,600.00 300.00 250.00 150.00 500.00 350.00 300.00 225.00 175.00 140.00 90.00 140.00 120.00 85.00 140.00 125.00 95.00 160.00 150.00
10
Code No. 0413 0414 0417 0418 0419 0420 0421 0422 0423 0424 0425 0426 0427 0428 0429 0430 0431 0432 0433 0438 0442 0444 0445 0446 0447 0449 0450 0451 0452 0453 0524 0525 0526
Description Brass mortice latch and lock 100 x 65 mm with 6 levers and a pair of brass lever handles Brass mortice latch 100x65 mm with a pair of brass lever handles Brass 150 mm floor door stopper (0.357 kg) Brass hard drawn hooks and eyes 300 mm Brass hard drawn hooks and eyes 250 mm Brass hard drawn hooks and eyes 200 mm Brass hard drawn hooks and eyes 150 mm Brass hard drawn hooks and eyes 100 mm Brass casement window fastener Brass casement stays (straight peg type ) 300 mm weighing not less than 0.33 kg Brass casement stays (straight peg type ) 250 mm weighing not less than 0.28 kg Brass casement stays (straight peg type ) 200 mm weighing not less than 0.24 kg Brass quadrant stays 300 mm Brass fanlight catch Brass fanlight pivot Brass chain with hook for fan light catch Brass hasps and staples (safety type) 150 mm Brass hasps and staples (safety type) 115 mm Brass hasps and staples (safety type) 90 mm Brass Night latch Brass helical spring 150 mm Brass curtain rod 20 mm dia 1.25 mm thick Brass curtain rod 25 mm dia 1.25 mm thick Brass brackets (curtain rods) 20 mm Brass cupboard knob or wardrobe knob 50 mm Brass screws 50 mm Brass screws 40 mm Brass screws 30 mm Brass screws 25 mm Brass screws 20 mm Chromium plated Brass butt hinges (heavy) type 75x65x4 mm (200 gms) Chromium plated Brass butt hinges (light/ordinary) type 125x70x4 mm Chromium plated Brass butt hinges (light/ordinary) type 100x70x4 mm
Unit
Rate
each each each 10 nos 10 nos 10 nos 10 nos 10 nos each each each each each 10 nos 10 nos each 10 nos 10 nos 10 nos each each metre metre each each 100 nos 100 nos 100 nos 100 nos 100 nos 10 nos 10 nos 10 nos
350.00 300.00 160.00 700.00 675.00 625.00 600.00 500.00 45.00 120.00 100.00 90.00 120.00 170.00 190.00 30.00 700.00 600.00 500.00 450.00 300.00 100.00 120.00 40.00 30.00 200.00 160.00 130.00 95.00 80.00 950.00 810.00 675.00
11
Code No. 0527 0528 0555 0556 0557 0558 0568 0569 0570 0571 0583 0584 0585 0586 0587 0588 0589 0590 0591 0592 0594 0595 0596 0597 0608 0635 0637 0638 0639 0640 0641 0642
Description Chromium plated Brass butt hinges (light/ ordinary) type 75x40x2.5 mm Chromium plated Brass butt hinges (light/ ordinary) type 50x40x2.5 mm Chromium plated Brass handles 125 mm with plate 175 x32 mm Chromium plated Brass handles 100 mm with plate 150 x 32 mm Chromium plated Brass handles 75mm with plate 125x32 mm Chromium plated Brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever handles Chromium plated brass casement window fastener Chromium plated Brass casement stays (straight peg type ) 300 mm weighing not less than 0.33 kg Chromium plated Brass casement stays (straight peg type ) 250 mm weighing not less than 0.28 kg Chromium plated Brass casement stays (straight peg type ) 200 mm weighing not less than 0.24 kg Chromium plated Brass Night latch Chromium plated Brass Wardrobe Knob 50 mm Chromium plated Brass screws 50 mm Chromium plated Brass screws 40 mm Chromium plated Brass screws 30 mm Chromium plated Brass screws 25 mm Chromium plated Brass screws 20 mm Chromium plated Brass curtain rod 12 mm dia 1.25 mm thick Chromium plated Brass curtain rod 20 mm dia 1.25 mm thick Chromium plated Brass curtain rod 25 mm dia 1.25 mm thick Bright finished or black enameled mild steel butt hinges 125x65x 2.12 mm Bright finished or black enameled mild steel butt hinges 100x58x 1.90 mm Bright finished or black enameled mild steel butt hinges75x47x 1.70 mm Bright finished or black enameled mild steel butt hinges50x37x 1.50 mm Nickel plated bright finished mild steel piano hinges 1 mm thick 25 mm wide Bright finished or black enameled mild steel screws 50 mm Bright finished or black enameled mild steel screws 40 mm Bright finished or black enameled mild steel screws 30 mm Bright finished or black enameled mild steel screws 25 mm Bright finished or black enameled mild steel screws 20 mm Bright finished or black enameled mild steel bolts and nuts 50x6 mm Oxidised mild steel butt hinges 125x65x2.12 mm
Unit 10 nos 10 nos each each each each each each each each each each 100 nos 100 nos 100 nos 100 nos 100 nos metre metre metre 10 nos 10 nos 10 nos 10 nos metre 100 nos 100 nos 100 nos 100 nos 100 nos each 10 nos
Rate 425.00 185.00 160.00 140.00 120.00 500.00 90.00 140.00 120.00 100.00 500.00 45.00 230.00 190.00 150.00 115.00 100.00 180.00 250.00 330.00 130.00 80.00 60.00 45.00 35.00 60.00 50.00 40.00 30.00 25.00 5.00 130.00
12
Code No. 0643 0644 0645 0646 0647 0648 0649 0650 0651 0652 0653 0654 0655 0656 0660 0661 0662 0663 0664 0665 0666 0667 0668 0669 0670 0679 0680 0681 0682 0683 0684 0685 0686
Description Oxidised mild steel butt hinges 100x58x1.90 mm Oxidised mild steel butt hinges75x47x1.70 mm Oxidised mild steel butt hinges50x37x1.50 mm Oxidised mild steel parliamentary hinges150x125x27x2.8 mm Oxidised mild steel parliamentary hinges 125x125x27x2.8 mm Oxidised mild steel parliamentary hinges 100x125x27x2.8 mm Oxidised mild steel parliamentary hinges 75x100x20x2.24 mm Oxidised mild steel single acting spring hinges 150 mm Oxidised mild steel single acting spring hinges 125 mm Oxidised mild steel single acting spring hinges 100 mm Oxidised mild steel double acting spring hinges 150 mm Oxidised mild steel double acting spring hinges 125 mm Oxidised mild steel double acting spring hinges 100 mm Nickel plated mild steel piano hinges 1 mm thick 35 mm wide Oxidised mild steel sliding door bolt 300x16 mm Oxidised mild steel sliding door bolt 250x16 mm Oxidised mild steel door latch 300x20x6 mm Oxidised mild steel door latch 250x20x6 mm Oxidised mild steel tower bolt (barrel type) 250x10 mm Oxidised mild steel tower bolt (barrel type) 200x10 mm Oxidised mild steel tower bolt (barrel type) 150x10 mm Oxidised mild steel tower bolt (barrel type) 100x10 mm Oxidised mild steel handles 125 mm Oxidised mild steel handles 100 mm Oxidised mild steel handles75 mm Oxidised mild steel hasps and staples (safety type) 150 mm Oxidised mild steel hasps and staples (safety type) 115 mm Oxidised mild steel hasps and staples (safety type) 90 mm Oxidised mild steel screws 50 mm Oxidised mild steel screws 40 mm Oxidised mild steel screws 30 mm Oxidised mild steel screws 25 mm Oxidised mild steel screws 20 mm
Unit 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each each each each each each metre each each each each each each each each each each each 10 nos 10 nos 10 nos 100 nos 100 nos 100 nos 100 nos 100 nos
Rate 80.00 55.00 45.00 320.00 300.00 225.00 190.00 105.00 100.00 80.00 110.00 105.00 85.00 40.00 90.00 80.00 45.00 40.00 40.00 35.00 25.00 20.00 17.00 15.00 14.00 120.00 100.00 75.00 70.00 50.00 45.00 35.00 30.00
13
Code No. 0687 0688 0689 0690 0691 0692 0693 0694 0696 0697 0698 0699 0700 0701 0702 0703 0704 0705 0706 0713 0714 0715 0717 0718 0719 0752 0753 0754 0755
Description Anodised Aluminium butt hinges 125x75x4 mm Anodised Aluminium butt hinges 125x63x4 mm Anodised Aluminium butt hinges 100x75x4 mm Anodised Aluminium butt hinges 100x63x3.2 mm Anodised Aluminium butt hinges 100x63x4 mm Anodised Aluminium butt hinges 75x63x4 mm Anodised Aluminium butt hinges 75x63x3.2 mm Anodised Aluminium butt hinges 75x45x3.2 mm Anodised Aluminium sliding door bolt 300x16 mm Anodised Aluminium sliding door bolt 250x16 mm Anodised Aluminium tower bolt (barrel type) 300x10 mm Anodised Aluminium tower bolt (barrel type) 250x10 mm Anodised Aluminium tower bolt (barrel type) 200x10 mm Anodised Aluminium tower bolt (barrel type) 150x10 mm Anodised Aluminium tower bolt (barrel type) 100x10 mm Anodised Aluminium handles 125 mm with plate 175 x 32 mm Anodised Aluminium handles 100 mm with plate 150 x 32 mm Anodised Aluminium handles 75mm with plate 125 x 32 mm Anodised Aluminium kicking plate 50 cm long 100x3.15 mm Block board construction flush door with teak wood ply on both faces 35 mm thick Block board construction flush door with teak wood ply on both faces 30 mm thick Block board construction flush door with teak wood ply on both faces 25 mm thick Block board construction flush door with commercial ply on both faces 35 mm thick Block board construction flush door with commercial ply on both faces 30 mm thick Block board construction flush door with commercial ply on both faces 25 mm thick Block board construction flush door lipping
Unit 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each each 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each sqm sqm sqm sqm sqm sqm sqm of door area
Rate 550.00 510.00 500.00 480.00 490.00 475.00 450.00 390.00 155.00 125.00 700.00 580.00 450.00 360.00 280.00 470.00 360.00 300.00 125.00 1,600.00 1,450.00 1,300.00 1,100.00 950.00 850.00 280.00
Square vision panel (upto 0.10 sqm) in Block board construction flush sqm of door door area Circular vision panel (upto 0.10 sqm) in Block board construction flush sqm of door door area Decorative type Louvers (upto 0.20 sqm) in Block board construction sqm of flush door door area
14
Code No. 0757 0759 0761 0763 0765 0768 0769 0770 0771 0773 0775 0776 0777 0784 0785 0788 0810 0811 0815 0816 0818 0820 0821 0823 0826 0827 0828 0829 0830 0831 0833 0834 0835 0845
Description Rebate cutting in Block board construction flush door Decorative plywood 4 mm Fuel wood Glue Hessian cloth Cement Concrete Jali 50 mm thick Cement Concrete Jali 40 mm thick Cement Concrete Jali 25 mm thick Kerosene oil Unslaked lime Dehradun white lime Satna lime Dry hydrated lime (factory made) Marble dust/ powder Marble chips up to 4 mm and downsize White & black Marble chips large size above 4 mm White & black Moorum Mud (dry) Dry distemper Oil bound washable distemper/ Acrylic distemper Linseed oil (double boiled) Cement primer Distemper primer Pink primer (for wood) Aluminium paint Acid proof paint (chocolate or black) Anticorrosive bituminous paint (black) Black Japan Enamel paint Floor enamel paint in all shades except green Synthetic enamel paint in black or chocolate shade Synthetic enamel paint in all shades except black or chocolate shade Plastic emulsion paint Roofing paint for iron sheets in red colour
Unit sqm of door area sqm quintal kilogram sqm sqm sqm sqm litre quintal quintal quintal quintal cum quintal quintal cum cum kilogram kilogram litre litre litre litre litre litre litre litre litre litre litre litre litre litre
Rate 80.00 400.00 450.00 65.00 20.00 210.00 180.00 145.00 30.00 300.00 410.00 230.00 220.00 1,000.00 180.00 180.00 450.00 50.00 35.00 42.00 100.00 80.00 80.00 85.00 115.00 105.00 85.00 90.00 125.00 120.00 130.00 135.00 165.00 110.00
15
Code No. 0850 0851 0855 0856 0857 0858 0859 0863 0865 0868 0869 0870 0873 0874 0875 0876 0886 0966 0967 0969 0973 0974 0975 0976 0977
Description White lead Water proofing cement paint Wax polish (ready made) Ordinary varnish Superior copal varnish Superior spar varnish Oil type wood preservative Putty for wood work Pig lead Premixed super white gypsum plaster Plaster of Paris Plug Copper pins 6 mm dia 7.5 cm long Black colour dark shade pigment Red, chocolate, orange, buff or yellow (red oxide of iron) light shade Green or blue medium shade pigment Standard holder bat clamps for sand cast iron or cast iron pipes 150mm dia Sand Cast iron plain shoe 150 mm dia Copper plate Pulley 25 mm dia Rolling shutter made of 80x1.25 mm machine rolled laths Top cover for rolling shutters 1.25 mm thick. 27.5 cm long wire spring grade no 2 for rolling shutters Ball bearing for rolling shutters Extra for mechanical devices chain and cranked operation for operating rolling shutters : exceeding 10.00 sqm and up to 16.80 sqm area of door Extra for mechanical devices chain and cranked operation for operating rolling shutters : exceeding 16.80 sqm area of door Royalty for good earth Royalty for sludge Coarse sand (zone III) Fine sand (zone IV) Galvanised steel plain sheets Standard quality hard board sheet 3 mm thick
Unit kilogram kilogram kilogram litre litre litre litre kilogram kilogram kilogram kilogram each each kilogram kilogram kilogram each each kilogram each sqm metre each each
Rate 80.00 40.00 175.00 65.00 125.00 125.00 70.00 30.00 90.00 7.00 4.00 8.00 10.00 55.00 70.00 60.00 25.00 325.00 270.00 30.00 1,150.00 550.00 250.00 330.00
16
Code No. 0996 0999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1013 1015 1019 1020 1021 1022 1023 1024 1025 1028 1029 1030 1031 1032 1034 1035 1036 1143 1145
Description Standard quality hard board sheet 4.5 mm thick Shellac Spirit Spun yarn Mild steel round bar 12 mm dia and below Mild steel round bar above 12 mm dia Average rate of Mild steel round bars for reinforcements Twisted steel / deformed bars Mild steel square bars Structural steel such as tees, angles, channels and R.S. joists Flats up to 10 mm in thickness Flats exceeding 10 mm in thickness Mild steel plates Mild steel sheets for tanks Mild steel expanded metal 20x60 mm strands Mild steel hooks Mild steel rivets Hard drawn steel wire fabric Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots Galvanised steel J or L hooks 8 mm dia Galvanised steel bolts & nuts 10 mm dia and 125 mm long round head with slots Mild stel bolts 6 mm dia and 25 mm long with hexagonal head Straining bolts Galvanised steel barbed wire Galvanised steel turn buckles Galvanised steel bolts & nuts 10 mm dia and 27 cm long both sides threaded with 4 galvanised steel nuts Galvanised steel bolts 10 mm dia and 7 cm long with nuts Bolts and nuts up to 300 mm in length Bolts and nuts above 300 mm in length Iron pintels including welded pin Steel beading size 10 x 10 x 1.6 mm (box type) Aluminium Plain Strip edging 38x12x3 mm
Unit sqm kilogram litre kilogram quintal quintal quintal quintal quintal quintal quintal quintal quintal quintal sqm each quintal sqm 10 nos 10 nos each 10 nos each quintal each each each quintal quintal each metre metre
Rate 130.00 205.00 65.00 40.00 4,100.00 4,000.00 4,050.00 4,500.00 4,250.00 4,250.00 4,200.00 4,150.00 4,500.00 4,600.00 270.00 30.00 4,800.00 430.00 20.00 90.00 10.00 25.00 70.00 5,175.00 15.00 20.00 15.00 5,400.00 5,400.00 35.00 20.00 95.00
17
Code No. 1149 1151 1154 1157 1158 1159 1160 1161 1163 1164 1165 1166 1168 1169 1174 1175 1177 1179 1186 1187 1188 1189 1190 1194 1196 1197 1198 1199 1201 1202 1203 1207 1208 1209 1210
Description Glass strip 4 mm thick 40 mm deep Boundary stone top chisel dressed 15x15x90 cm Through and bond stone size 24 x24 x39 cm Stone for masonry work Stone for pitching 15 cm x 22.5 cm Stone dust Red sand stone block White sand stone block White sand stone slab 75 mm thick (un-dressed) Red sand stone slab 40 mm thick (un-dressed) White sand stone slab 40 mm thick (un-dressed) Red sand stone slab 30 mm thick (un-dressed) Kota stone slab 20 mm to 25 mm thick (semi-polished) Kota stone slab 25mm thick (rough chiseled) Red sand stone slab 45 mm to 50 mm thick (un-dressed) White sand stone slab 45 mm to 50 mm thick (un-dressed) Stone grit 6 mm and down size or pea sized gravel Crushed stone 2.36 mm to 12.5 mm size Superior class teak wood such as Dandeli, Balarshah or Malabar in planks First class teak wood in scantling First class teak wood in planks Second class teak wood in scantling Second class teak wood in planks Second class deodar wood in planks First class kail wood in planks Second class kail wood in scantling Second class kail wood in planks Sal wood in scantling Precast terrazzo tiles 22 mm thick (light shade) Precast terrazzo tiles 22 mm thick(medium shade) Precast terrazzo tiles 22 mm thick (dark shade) G.I. Limpet washer Bitumen washer G.I. plain washer thick G.I. plain washer thin
Unit metre each 100 nos cum cum cum 10 cudm 10 cudm sqm sqm sqm sqm sqm sqm sqm sqm cum cum 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm sqm sqm sqm 100 nos 100 nos 100 nos 100 nos
Rate 9.00 60.00 1,100.00 675.00 420.00 925.00 60.00 65.00 280.00 155.00 170.00 120.00 270.00 175.00 165.00 185.00 900.00 915.00 1,050.00 700.00 800.00 640.00 720.00 480.00 300.00 250.00 250.00 500.00 240.00 220.00 200.00 35.00 25.00 32.00 30.00
18
Code No. 1211 1213 1214 1215 1216 1219 1220 1221 1222 1224 1225 1227 1228 1229 1231 1234 1235 1237 1238 1241 1301 1304 1305 1307 1309 1314 1315 1330 1331 1332 1334 1335 1336 1337 1339 1340
Description G.I. plain washer for seam bolts Water proofing materials Welding by gas plant Welding by electric plant Whiting Wire nails Wire mesh (rabbit) 20 mm dia holding down bolts Mild steel sheets with bolts and nuts to rest on pintels Hard drawn steel wire Mild steel flat strap fitting Chequered terrazzo tiles 22 mm thick(light shade) Chequered terrazzo tiles 22 mm thick(medium shade) Chequered terrazzo tiles 22 mm thick (dark shade) Extra for selected planks of second class teakwood Aluminium Plain Strip edging 57x12x3 mm Diesel oil Cutting marble or sand stone slab up to 50 mm thick by mechanical device Extra for selected planks of first class teakwood Commercial LPG in cylinder. Bleaching powder Surface box for stop cock Surface box for sluice valve Surface box for water meter C.I. bracket for wash basin and sinks C.P.brass chain with 32 mm dia rubber plug C.P.brass chain with 40 mm dia rubber plug Clamps and M.S. stays including bolts and nuts for 100 mm pipe M.S.Holder bat clamp of approved design for 100 mm S.C.I. pipe M.S.Holder bat clamp of approved design for75 mm S.C.I. pipe Clamps and M.S. stays including bolts and nuts for 50 mm pipe Clamps and M.S. stays including bolts and nuts for 75 mm pipe Clearing eye with chain and lid 100 mm dia Clearing eye with chain and lid 150 mm dia Brass bib-cock 15 mm dia Brass bib-cock 20 mm dia
Unit 100 nos kilogram cm cm quintal kilogram sqm quintal each quintal quintal sqm sqm sqm 10 cudm metre litre metre 10 cudm kg quintal each each each pair each each each each each each each each each each each
Rate 32.00 25.00 1.50 1.50 400.00 52.00 45.00 5,400.00 110.00 4,200.00 3,950.00 300.00 260.00 225.00 115.00 130.00 41.29 8.00 140.00 51.00 1,750.00 100.00 185.00 205.00 53.00 26.00 27.00 33.00 17.00 15.00 25.00 29.00 44.00 50.00 165.00 215.00
19
Code No. 1342 1343 1350 1352 1353 1354 1355 1356 1357 1360 1361 1362 1363 1364 1366 1367 1369 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1392 1396 1397 1464 1466
Description Brass stop-cock 15 mm dia Brass stop-cock 20 mm dia Mosquito proof coupling of approved design C.I. cover and frame 300x300 mm inside C.I.cover without frame 300x300 mm inside i/c cover of 4.50 kg Rectangular cover 455x610 mm with frame (low duty) Rectangular cover 455x610 mm without frame (low duty) 500 mm dia cover with frame (medium duty) 500 mm dia cover without frame (medium duty) C.I.mouth, brass ferrule 15 mm dia C.I.mouth, brass ferrule 20 mm dia C.I.mouth, brass ferrule 25 mm dia Vitreous china foot rests 250x130x30 mm C.I. grating 100x100 mm C.I. grating 150x150 mm C.I. grating 180x180 mm S.C.I. gully or nahani grating 100 mm dia Rubber insertions for 80 mm dia pipe joints Rubber insertions for 100 mm dia pipe joints Rubber insertions for 125 mm dia pipe joints Rubber insertions for 150 mm dia pipe joints Rubber insertions for 200 mm dia pipe joints Rubber insertions for 250 mm dia pipe joints Rubber insertions for 300 mm dia pipe joints Rubber insertions for 350 mm dia pipe joints Rubber insertions for 400 mm dia pipe joints Rubber insertions for 450 mm dia pipe joints Rubber insertions for 500 mm dia pipe joints Rubber insertions for 600 mm dia pipe joints Mirror of superior make glass 60x45 cm Vitreous china pedestal for wash basin Pig lead S & S.C.I.standard specials up to 300 mm dia (heavy class) S & S.C.I.standard specials over 300 mm dia (heavy class)
Unit each each each each each each each each each each each each pair each each each each each each each each each each each each each each each each each each kilogram quintal quintal
Rate 165.00 215.00 27.00 280.00 200.00 1,415.00 980.00 4,435.00 2,210.00 115.00 145.00 205.00 90.00 15.00 25.00 30.00 15.00 11.00 14.00 15.00 17.00 22.00 32.00 40.00 45.00 67.00 84.00 106.00 118.00 290.00 650.00 90.00 3,450.00 3,550.00
20
Code No. 1468 1470 1472 1532 1533 1534 1535 1540 1541 1542 1543 1545 1546 1547 1548 1549 1550 1551 1552 1555 1559 1608 1612 1614 1616 1617 1618 1620 1621
Description Flanged C.I. standard specials up to 300 mm dia(heavy class) Flanged C.I. standard specials over 300 mm dia(heavy class) Casing pipe 100 mm dia Flush pipe with union spreaders and clamps all in C.P. brass for single stall Flush pipe with union spreaders and clamps all in C.P. brass for double stall Flush pipe with union spreaders and clamps all in C.P. brass for range of three stall Flush pipe with union spreaders and clamps all in C.P. brass for range of four stall Flush pipe and spreaders G.I.for single set of one squatting plate urinal Flush pipe and spreaders G.I.for range of two squatting plates urinal Flush pipe and spreaders G.I.for range of three squatting plates urinal each Flush pipe and spreaders G.I.for range of four squatting plates urinal G.I. pipes 15 mm dia G.I. pipes 20 mm dia G.I. pipes 25 mm dia G.I. pipes 32 mm dia G.I. pipes 40 mm dia G.I. pipes 50 mm dia G.I. pipes 65 mm dia G.I. pipes 80 mm dia G.I. back (jam) nuts 25 mm dia G.I. back (jam) nuts 65 mm dia G.I. tees (equal) 25 mm G.I. tees (equal) 65 mm G.I. inlet connection S.C.I. soil, waste and vent single socketed pipe1.80 metres long: 75mm dia S.C.I. soil, waste and vent single socketed pipe1.80 metres long: 100mm dia S.C.I. soil, waste and vent single socketed pipe1.80 metres long: 150mm dia S.C.I. plain bend 75 mm dia S.C.I. plain bend 100 mm dia
Unit quintal quintal metre each each each each each each each each metre metre metre metre metre metre metre metre each each each each each each each each each each
Rate 5,300.00 5,600.00 335.00 240.00 380.00 490.00 570.00 170.00 230.00 290.00 365.00 81.00 97.00 134.00 167.00 202.00 254.00 325.00 426.00 8.00 18.00 42.00 270.00 61.00 890.00 990.00 1,630.00 170.00 210.00
21
Code No. 1622 1624 1625 1627 1628 1630 1631 1633 1634 1636 1637 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1653 1656 1659 1662 1666
Description S.C.I. plain bend 150 mm dia S.C.I. bend with access door 75 mm dia S.C.I. bend with access door 100 mm dia S.C.I. plain single equal junctions 75x75x75 mm dia S.C.I. plain single equal junctions 100x100x100 mm dia S.C.I. single equal junctions75x75x75 mm dia with access door S.C.I. single equal junctions 100x100x100 mm dia with access door S.C.I. plain double equal junctions 75x75x75x75 mm dia S.C.I. plain double equal junctions100x100x100x100 mm dia S.C.I. double equal junctions75x75x75x75 mm dia with access door S.C.I. double equal junctions 100x100x100x100 mm dia with access door Slotted cowl (terminal guard) 75 mm dia Slotted cowl (terminal guard) 100 mm dia G.I. Union 15 mm nominal bore G.I. Union 20 mm nominal bore G.I. Union 25 mm nominal bore G.I. Union 32 mm nominal bore G.I. Union 40 mm nominal bore G.I. Union 50 mm nominal bore G.I. Union 65 mm nominal bore G.I. Union 80 mm nominal bore Polyethylene water storage tank with cover and suitable locking arrangement Sand cast iron S&S plain single unequal junctions : 100x100x75 mm dia Sand cast iron S&S single unequal junctions: 100x100x75 mm dia with access door. Sand cast iron S&S plain double unequal junctions : 100x100x75x75 mm dia Sand cast iron S&S double unequal junctions: 100x100x75x75 mm dia with access door Sand cast iron heel rest bend 75 mm dia
Unit each each each each each each each each each each each each each each each each each each each each each per litre each each each each each
Rate 470.00 187.00 233.00 240.00 310.00 260.00 350.00 335.00 490.00 395.00 530.00 137.00 187.00 40.00 60.00 70.00 100.00 135.00 180.00 390.00 480.00 4.45 350.00 390.00 510.00 550.00 200.00
22
Code No. 1667 1669 1670 1672 1673 1674 1677 1682 1683 1685 1686 1687 1688 1689 1690 1693 1700 1701 1702 1703 1704 1705 1706 1707 1709 1710 1711 1712 1713 1714 1715
Description Sand cast iron heel rest bend 100 mm dia S.C.I. single equal invert branch of required degree75x75x75 mm dia S.C.I. single equal invert branch of required degree 100x100x100 mm dia S.C.I. double equal invert branch of required degree 75x75x75x75 mm dia S.C.I. double equal invert branch of required degree 100x100x100x100 mm dia S.C.I. single unequal invert branch of required degree100x100x75 mm dia S.C.I. double unequal invert branchof required degree 100x100x75x75 mm dia S.C.I. door pieces 75 mm dia S.C.I. door pieces 100 mm dia S.C.I. collar 75 mm dia S.C.I. collar 100 mm dia Unplasticised P.V.C. connection pipe with brass union 30 cm long 15 mm bore Unplasticised P.V.C. connection pipe with brass union 30 cm long 20 mm bore Unplasticised P.V.C. connection pipe with brass union 45 cm long 15 mm bore Unplasticised P.V.C. connection pipe with brass union 45 cm long 20 mm bore S.C.I. hand pump R.C.C. pipes NP2 class 100 mm dia R.C.C. pipes NP2 class 150 mm dia R.C.C. pipes NP2 class 250 mm dia R.C.C. pipes NP2 class 300 mm dia R.C.C. pipes NP2 class 450 mm dia R.C.C. pipes NP2 class 500 mm dia R.C.C. pipes NP2 class 600 mm dia R.C.C. pipes NP2 class 700 mm dia R.C.C. pipes NP2 class 800 mm dia R.C.C. pipes NP2 class 900 mm dia R.C.C. pipes NP2 class 1000 mm dia R.C.C. pipes NP2 class 1100 mm dia R.C.C. pipes NP2 class 1200 mm dia R.C.C. collarsNP2 class 100 mm dia R.C.C. collarsNP2 class 150 mm dia
Unit each each each each each each each each each each each each each each each each metre metre metre metre metre metre metre metre metre metre metre metre metre each each
Rate 239.00 290.00 387.00 382.00 510.00 466.00 545.00 253.00 350.00 98.00 133.00 26.00 33.00 33.00 43.00 550.00 135.00 154.00 188.00 261.00 380.00 454.00 732.00 850.00 960.00 1,125.00 1,420.00 1,730.00 1,760.00 20.00 25.00
23
Code No. 1716 1717 1718 1719 1720 1721 1723 1724 1725 1726 1727 1854 1855 1856 1858 1859 1863 1871 1872 1875 1876 1878 1879 1881 1882 1885 1889 1891 1893 1895 1896 1897 1898
Description R.C.C. collarsNP2 class 250 mm dia R.C.C. collarsNP2 class 300 mm dia R.C.C. collarsNP2 class 450 mm dia R.C.C. collarsNP2 class 500 mm dia R.C.C. collarsNP2 class 600 mm dia R.C.C. collarsNP2 class 700 mm dia R.C.C. collarsNP2 class 800 mm dia R.C.C. collarsNP2 class 900 mm dia R.C.C. collarsNP2 class 1000 mm dia R.C.C. collarsNP2 class 1100 mm dia R.C.C. collarsNP2 class 1200 mm dia Stoneware pipes grade A (60 cm long) 100 mm dia Stoneware pipes grade A (60 cm long) 150 mm dia Stoneware pipes grade A (60 cm long) 200 mm dia Stoneware pipes grade A (60 cm long) 250 mm dia Stoneware pipes grade A (60 cm long) 300 mm dia Fire clay kitchen sink: 600x450x250 mm White vitreous china laboratory sink450x300x150 mm White vitreous china laboratory sink600x450x200 mm White plastic seat (solid)with lid C.P.brass hinges and rubber buffers Black plastic seat (solid) with lid C.P.brass hinges and rubber buffers Shower rose C.P.brass for 15 to 20 mm inlet 100 mm dia Shower rose C.P.brass for 15 to 20 mm inlet 150 mm dia Spun yarn Strainer brass 40 mm dia 1.5 metre long 15 mm C.P.brass tap C.P.brass toilet paper holder of standard size C.I. trap for standard urinal with vent arm with operating and other couplings in C.P.brass: 50 mm dia C.I. trap for standard urinal with vent arm with operating and other couplings in C.P.brass: 80 mm dia C.P.brass trap40 mm dia 100 mm S.C.I. trap with vent heel 100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet 100 mm S.C.I. trap with 100 mm inlet and 75 mm outlet
Unit each each each each each each each each each each each each each each each each each each each each each each each kilogram each each each each each each each each each
Rate 40.00 49.00 75.00 89.00 109.00 121.00 172.00 210.00 256.00 283.00 330.00 36.00 53.00 91.00 130.00 190.00 1,350.00 820.00 1,525.00 310.00 293.00 40.00 55.00 40.00 495.00 170.00 115.00 158.00 200.00 125.00 308.00 263.00 198.00
24
Code No. 1900 1902 1904 1913 1915 1922 1923 1924 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1940 1941 1942 1943 1944 1945 1947 1949 1950 1951 1952 1953 1954 1955 1956 1957
Description S.W. gully trap P type 100x100 mm S.W. gully trap P type 150x100 mm S.W. gully trap P type 180x150 mm Vitreous china lipped front urinal Vitreous china squatting plate urinal H.P. or L.P. ball valve with polythene floats: 15 mm dia H.P. or L.P. ball valve with polythene floats: 20 mm dia H.P. or L.P. ball valve with polythene floats: 25 mm dia Brass full way valve with C.I. wheel (screwed end) 25 mm dia Brass full way valve with C.I. wheel (screwed end) 32 mm dia Brass full way valve with C.I. wheel (screwed end) 40 mm dia Brass full way valve with C.I. wheel (screwed end) 50 mm dia Brass full way valve with C.I. wheel (screwed end) 65 mm dia Brass full way valve with C.I. wheel (screwed end) 80 mm dia Gunmetal non-return valve-horizontal (screwed end) 25 mm dia Gunmetal non-return valve-horizontal (screwed end) 32 mm dia Gunmetal non-return valve-horizontal (screwed end) 40 mm dia Gunmetal non-return valve-horizontal (screwed end) 50 mm dia Gunmetal non-return valve-horizontal (screwed end) 65 mm dia Gunmetal non-return valve-horizontal (screwed end) 80 mm dia C.I.sluice valve (with caps) class I : 100 mm dia C.I.sluice valve (with caps) class I : 125 mm dia C.I.sluice valve (with caps) class I : 150 mm dia C.I.sluice valve (with caps) class I : 200 mm dia C.I.sluice valve (with caps) class I : 250 mm dia C.I.sluice valve (with caps) class I : 300 mm dia Vitreous china flat back wash basin 630x450 mm Vitreous china angle back wash basin 600x480 mm Vitreous china angle back wash basin 400x400 mm C.P. brass waste 32 mm C.P. brass waste 40 mm Vitreous china Indian type w.c. pan size 580 mm Vitreous china orrisa type w.c. pan size 580 mm Vitreous china pedestal type water closet Bolts and nuts 16 mm dia 60 mm long Bolts and nuts 16 mm dia 65 mm long
Unit each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each each
Rate 70.00 104.00 195.00 460.00 740.00 190.00 270.00 315.00 305.00 370.00 450.00 650.00 900.00 1,550.00 310.00 400.00 510.00 780.00 1,420.00 2,030.00 2,300.00 2,600.00 3,410.00 6,550.00 9,550.00 13,500.00 675.00 580.00 405.00 55.00 62.00 340.00 750.00 680.00 10.00 11.00
25
Code No. 1958 1959 1960 1961 1962 1963 1964 1965
Description Bolts and nuts 20 mm dia 65 mm long Bolts and nuts 20 mm dia 70 mm long Bolts and nuts 20 mm dia 75 mm long Bolts and nuts 20 mm dia 80 mm long Bolts and nuts 24 mm dia 85 mm long Bolts and nuts 24 mm dia 90 mm long Bolts and nuts 27 mm dia 100 mm long White vitreous china dual purpose closet (Anglo Indian W.C.) suitable for use as squatting pan or European type water closet as per manufacturer's specifications Vitreous china foot rests 250x125x25 mm Fly ash Common burnt clay F.P.S.(non modular) bricks tile class designation 10 Common burnt clay modular bricks class designation 12.5 Strips-Aluminium fluted 3.15 mm thick and 150 mm wide Strips Aluminium fluted 3.15 mm thick and 200 mm wide Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm) Float glass sheet of nominal thickness 5.5 mm.(weight not less than 13.50 kg/sqm) Ply wood 5 ply with commercial ply on both faces 6 mm thick Hollock ballies 125 mm diameter Oxidised mild steel pull bolt lock (locking bolt) of size 85 mm x 42 mm with screws, bolts, nuts and washers complete Brass cupboard lock 6 levers of approved quality, 40 mm size Brass cupboard lock 6 levers of approved quality, 50 mm size Brass cupboard lock 6 levers of approved quality, 65 mm size Brass cupboard lock 6 levers of approved quality, 75 mm size Brass hanging type door stopper 150 mm Hydraulic door closer bottle type M.S. body with necessary accessories and screws complete Anodised Aluminium hanging type door stopper Anodised Aluminium pull bolt lock (locking bolt) of size 85 mmx42 mm with screws, bolts ,nuts and washers complete Anodised Aluminium Casement stay 250 mm Hollock wood in scantling Chromium plated Brass pull bolt lock (locking bolt) of size 85 mmx42 mm with screws, bolts, nuts and washers complete Nickeled Chromium Brass cupboard lock 40 mm size Nickeled Chromium Brass cupboard lock 50 mm size
each pair cum 1000 nos 1000 nos metre metre sqm sqm sqm metre each each each each each each each each each each 10 cudm each each each
1,250.00 100.00 7.75 3,100.00 3,600.00 228.00 323.00 310.00 450.00 340.00 35.00 44.00 65.00 70.00 75.00 95.00 60.00 535.00 21.00 46.00 46.00 310.00 145.00 62.00 70.00
1970 1980 1984 1986 2391 2392 2406 2407 2412 2447 2449 2451 2452 2453 2454 2455 2456 2459 2464 2465 2466 2467 2468 2469
26
Code No. 2470 2471 2480 2481 2483 2500 2504 2505 2602 2603 2704 2710 2750 2751 2901 2902 2903 2904 2908 2909 2910 2911 2914 2916 3002 3004 3050 3080 3084 3088 3092 3096
Description Nickeled Chromium Brass cupboard lock 65 mm size Nickeled Chromium Brass cupboard lock 75 mm size Ply wood 5 ply with teak ply on both faces 9 mm thick Ply wood 5 ply with teak ply on one face and commercial ply on another face 9 mm thick Ply wood 7 ply with teak ply on one face and commercial ply on another face 9 mm thick Extra for selected planks of second class deodar wood Kiln seasoning of timber Hollock wood in planks Common burnt clay F.P.S. (non modular) bricks class designation 7.5 Common burnt clay F.P.S. (non modular) bricks class designation 5.0 Aluminium Strip 40 mm wide and 2 mm thick White marble makrana second quality plain veined stone pieces for crazy flooring 8 mm thick granite stone tiles (mirror polished of all shades) 8 mm thick marble tiles (polished) Raj Nagar Stone Aggregate (Single size) : 100 mm nominal size Stone Aggregate (Single size) : 80 mm nominal size Stone chippings/ screenings 4.75 mm nominal size Stone chippings/ screenings 150 micron nominal size Over burnt (Jhama) Brick Aggregate: 120 mm to 40 mm size Over burnt (Jhama) Brick Aggregate: 90 mm to 40 mm size Stone chippings/ screenings 12.5/ 13.2 mm nominal size Stone chippings/ screenings 10/ 11.2 mm nominal size Solvent Paving Asphalt VG -10 of approved quality Polyvinyl chloride sheet 400 micron thick Stone ware spouts 100 mm dia 60 cm long Galvanised steel corrugated sheets Gunmetal non-return valve-vertical (screwed end) 25 mm dia Gunmetal non-return valve-vertical (screwed end) 32 mm dia Gunmetal non-return valve-vertical (screwed end) 40 mm dia Gunmetal non-return valve-vertical (screwed end) 50 mm dia Gunmetal non-return valve-vertical (screwed end) 65 mm dia
Unit each each sqm sqm sqm 10 cudm cum 10 cudm 1,000 nos 1,000 nos kilogram quintal sqm sqm cum cum cum cum cum cum cum cum kilogram tonne sqm each quintal each each each each each
Rate 82.00 103.00 960.00 775.00 845.00 73.00 680.00 350.00 2,900.00 2,450.00 210.00 130.00 675.00 340.00 750.00 750.00 1,150.00 1,150.00 330.00 360.00 1,050.00 1,050.00 23.00 37,500.00 31.00 33.00 5,075.00 320.00 490.00 680.00 930.00 1,650.00
27
Code No. 3213 3228 3229 3300 3311 3314 3317 3320 3321 3326 3617 3620 3621 3624 3625 3628 3629 3634 3635 3640 3641 3644 3645 3650 3651 3654 3655 3660 3664
Description Vitreous china Surgeon type wash basin of size 660x460 mm 600x120 mm glass shelf with anodised aluminium angle frame, C.P. brass brackets and guard rail of standard size Vitreous china flat back wash basin 550x400 mm Gunmetal non-return valve-vertical (screwed end) 80 mm dia C.I.sluice valve (with caps) class II : 100 mm dia C.I.sluice valve (with caps) class II : 125 mm dia C.I.sluice valve (with caps) class II : 150 mm dia C.I.sluice valve (with caps) class II : 200 mm dia C.I.sluice valve (with caps) class II : 250 mm dia C.I.sluice valve (with caps) class II : 300 mm dia CP Brass Union 40 mm dia C.C.I.(spun) socketed soil, waste and vent pipe 1.80 metres long : 100 mm dia C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres long : 75 mm dia S.C.I. S&S bends with access door 100 mm dia S.C.I. S&S bends with access door 75 mm dia S.C.I. S&S bend 100 mm dia S.C.I. S&S bend 75 mm dia S.C.I. S&S heel rest sanitary bend 100 mm dia S.C.I. S&S heel rest sanitary bend 75 mm dia S.C.I. S&S single equal junctions100x100x100 mm S.C.I. S&S single equal junctions 75x75x75 mm S.C.I. S&S single equal junctions with access door 100x100x100 mm S.C.I. S&S single equal junctions with access door 75x75x75 mm S.C.I. S&S double equal junctions 100x100x100x100 mm S.C.I. S&S double equal junctions 75x75x75x75 mm S.C.I. S&S double equal junctions with access door 100x100x100x 100 mm S.C.I. S&S double equal junctions with access door 75x75x75x75 mm S.C.I. S&S single unequal junctions 100x100x75 mm S.C.I. S&S single unequal junctions with access door 100x100x75 mm
Unit each each each each each each each each each each each each each each each each each each each each each each each each each each each each each
Rate 995.00 130.00 530.00 2,630.00 2,650.00 3,200.00 4,000.00 9,100.00 13,500.00 17,000.00 175.00 1,130.00 985.00 270.00 215.00 235.00 175.00 275.00 240.00 430.00 310.00 465.00 350.00 565.00 450.00 610.00 475.00 560.00 630.00
28
Code No. 3670 3674 3681 3682 3685 3686 3690 3695 3699 3707 3708 3712 3713 3716 3717 3728 3729 3733 3734 3738 3739 3746 3747 3749 3860 3861 4006 4007 4008
Description S.C.I. S&S double unequal junctions100x100x75x75 mm S.C.I. S&S double unequal junctions with access door 100x100x75x75 mm S.C.I. S&S single equal invert branch of required degree 100x100x100 mm dia S.C.I. S&S single equal invert branch of required degree 75x75x75 mm dia S.C.I. S&S double equal invert branch of required degree100x100x100x 100 mm dia S.C.I. S&S double equal invert branch of required degree 75x75x75x 75 mm dia S.C.I. S&S single unequal invert branch of required degree100x100x 75 mm dia S.C.I. S&S double unequal invert branch of required degree100x100x 75x75 mm dia S.C.I. S&S, 75 mm offset for 75 mm dia pipe S.C.I. S&S, 150 mm offset for 75 mm dia pipe S.C.I. S&S, 150 mm offset for 100 mm dia pipe S.C.I. S&S, 114 mm offset for 75 mm dia pipe S.C.I. S&S, 114 mm offset for 100 mm dia pipe S.C.I. S&S, 152 mm offset for 75 mm dia pipe S.C.I. S&S, 152 mm offset for 100 mm dia pipe S.C.I. S&S door pieces 100 mm dia S.C.I. S&S door pieces 75 mm dia S.C.I. S&S, Slotted Cowl (Terminal Guard) 100 mm S.C.I. S&S, Slotted Cowl (Terminal Guard) 75 mm S.C.I. S&S, collars 100 mm S.C.I. S&S, collars 75 mm S.C.I. S&S, 75 mm offset for 75 mm dia pipe S.C.I. S&S, 75 mm offset for 100 mm dia pipe Vitreous china toilet paper holder of standard size 560 mm dia cover with frame (Heavy duty) 560 mm dia cover without frame (Heavy duty) Pressed steel door frames (mild steel sheet 1.60 mm) Profile B Pressed steel door frames (mild steel sheet 1.60 mm) Profile C Pressed steel door frames (mild steel sheet 1.60 mm) Profile E
Unit each each each each each each each each each each each each each each each each each each each each each each each each each each metre metre metre
Rate 780.00 850.00 395.00 303.00 525.00 405.00 505.00 700.00 215.00 270.00 370.00 270.00 355.00 335.00 440.00 370.00 260.00 190.00 175.00 185.00 130.00 215.00 246.00 118.00 8,460.00 4,500.00 220.00 240.00 270.00
29
Code No. 4009 4010 4011 4012 4013 4201 4202 4203 4204 4205 4206 4207 5001 6001 6007 6010 6019 6501 7001 7003 7004 7005 7006 7008 7009 7010 7011 7012 7013 7014
Description Mild steel tubes hot finished welded type Mild steel tubes hot finished seamless type Mild steel tubes electric resistant or induction butt welded Circular C.I. Box for ceiling fan Pulley 40 mm dia Aluminium primer Red oxide Zinc chromate primer Copper acetate Hydrochloric acid Copper chloride Copper nitrate Ammonium chloride Mobil oil White marble slab Makrana second quality plain veined 18 mm thick Pink marble slab plain 18 mm thick Udaypur green marble slab plain 18 mm thick Black Zebra marble slab plain 18 mm thick Sand zone V (Jamuna) Brass 100 mm mortice latch and lock with 6 levers without pair of handles Pair of Anodised Aluminium lever handles for 100 mm mortice latch and lock Vitreous china flat back wash basin 450x300 mm Vitreous china 10 litres low level cistern without fittings Vitreous china 10 litres low level cistern with fittings F.P.S.(non modular) clay fly ash bricks class designation 7.5 12.5 mm thick tapered edge gypsum plain borad Galvanised Steel celling section (size 80x26x0.50 mm) Galvanised Steel perimetre Channel (Size 20x27x30x0.50 mm) Galvanised Steel intermediate Channel (Size 15x45x15x0.90 mm) Galvanised Steel angle hanger (Celling angle) (Size 25x10x0.50 mm) Galvanised Steel connecting clips (2.64 mm dia and 230 mm long GI wire)
Unit kilogram kilogram kilogram each each litre litre kilogram kilogram kilogram kilogram kilogram litre sqm sqm sqm sqm cum each each each each each 1,000 nos sqm metre metre metre metre each
Rate 48.00 58.00 65.00 50.00 25.00 72.00 68.00 270.00 32.00 272.00 200.00 15.00 186.00 1,850.00 610.00 660.00 470.00 500.00 250.00 300.00 425.00 890.00 1,550.00 3,000.00 160.00 39.00 27.00 42.00 19.00 6.20
30
Code No. 7015 7016 7017 7018 7019 7020 7021 7022 7023 7024 7027 7029 7032 7033 7034 7035 7036 7040 7042 7043 7044 7045 7046 7047 7048 7049 7055 7056 7059 7060 7063 7064
Description Galvanised Steel soffit cleat (Size 27x37x25x0.60 mm) Joint filler Joint finisher Joint tape roll Dash fastener/Chemical Fastener All drive screws (for gypsum board) Primer ( for gypsum board) Chlorpyriphos 20% E.C. / Lindane 20% E.C. Chromium plated brackets ( curtain rods) Acid Proof cement M.S. Butt hinges 125x90x4 mm Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia. of wire 0.63 mm Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) Nickel plated M.S. pipe 25 mm dia. Nickel plated M.S. pipe 20 mm dia. Nickel plated M.S. Brackets for curtain rod 20 mm Nickel plated M.S. Brackets for curtain rod 25 mm Oxidised mild steel screws 35 mm Mild steel conduit pipe (heavy type) ISI marked-20 mm dia. Mild steel conduit pipe (heavy type) ISI marked-25 mm dia. Rolling shutters of 80x0.90 mm laths Rolling shutters of 80x1.2 mm laths Top cover of Rolling shutters 0.90 mm thick Top cover of Rolling shutters 1.20 mm thick Rawl plug 50 mm (designation 10 nos) Teak wood lipping of size 25x3 mm in pelmets Flat pressed 3 layer and graded particle board (medium density) Grade 1 conforming to IS : 3087 - 18 mm thick Aluminium tee channel (heavy duty) with rollers and stop end Aluminium hanging floor door stopper with twin rubber & stopper Hydraulic door closer tubular type Aluminium section body Oxidised M.S.casement stay (straight peg type) 300 mm not less than 0.33 kg Oxidised M.S.casement stay (straight peg type) 250 mm not less than 0.28 kg
Unit each kilogram kilogram roll each 100 nos litre litre each tonne 10 nos sqm sqm metre metre each each 100 nos metre metre sqm sqm metre metre each metre sqm metre each each each each
Rate 4.00 22.00 24.00 140.00 13.00 56.00 85.00 160.00 7.00 8,100.00 105.00 230.00 315.00 75.00 67.00 6.00 7.00 40.00 57.00 66.00 930.00 1,010.00 270.00 305.00 10.00 20.00 390.00 45.00 58.00 810.00 21.00 18.00
31
Code No. 7065 7068 7070 7071 7077 7087 7090 7091 7095 7096 7097 7098 7101 7102 7103 7104 7105 7106 7107 7112 7113 7114 7115 7116 7117 7118
Description Oxidised M.S.casement stay (straight peg type) 200 mm not less than 0.24 kg Extra for providing grilled rolling shutters with 8 mm dia M.S. rod Chequered precast cement concrete tiles 22 mm thick using marble chips of size 6 mm - light shade using white cement White marble Raj Nagar plain 18 mm thick upto 0.50 sqm area Acid and alkali resistant tiles 300x300 mm size, 10 mm thick S.C.I. Tee 150 mm Expanded polystyrene type N- Normal Expanded polystyrene type - SE Stainless steel kitchen sink - with drain board bowl depth 250 mm Stainless steel kitchen sink - with drain board 510 x 1040 mm bowl depth 225 mm. Stainless steel kitchen sink - with drain board 510 x 1040 mm bowl depth 200 mm. Stainless steel kitchen sink - with drain board 510x1040 mm bowl depth 178 mm Stainless steel kitchen sink - without drain board 610x510 mm bowl depth 200 mm Stainless steel kitchen sink - without drain board 610x460 mm bowl depth 200 mm Stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm Coloured Orissa pattern W.C. pan 580x440 mm Coloured Pedestal type W.C. pan 580x440 mm (European type) Coloured Vitreous china 10 lit. low level cistern Coloured (other than black) solid P.V.C. seat in European W.C. pan Circular shape 450 mm dia Mirror with Plastic moulded frame Rectangular shape 453x357 mm Mirror with Plastic moulded frame Oval shape 450x350 mm (outer dimensions) Mirror with Plastic moulded frame Rectangular shape 1500x450 mm Mirror with Plastic moulded frame Hard board 6 mm thick Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings
Unit
Rate
each sqm sqm sqm 10 nos each sqm sqm each each each each each each each each each each each each each each each sqm each each
17.00 225.00 470.00 545.00 520.00 505.00 130.00 155.00 5,150.00 4,900.00 4,200.00 2,900.00 2,950.00 2,750.00 2,050.00 1,275.00 1,080.00 1,500.00 475.00 390.00 260.00 300.00 670.00 170.00 21.00 27.00
32
Code No. 7119 7120 7123 7126 7127 7128 7129 7130 7131 7132 7133 7134 7135 7136 7137
Description Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings Flexible (coil shaped) PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings Coloured High density polyethylene/ poly propylene 10 lit. (full flush) capacity controlled low level flushing cistern with fittings White Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings Coloured Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings S.W. intercepting trap 100 mm dia S.W. intercepting trap 150 mm dia Rectangular shape 600x 450 mm precast R.C.C. manhole cover with frame - L.D. - 25 Square shape 450x450 mm precast R.C.C. manhole cover with frame L.D. - 25 Circular shape 450 mm dia precast R.C.C. manhole cover with frame L.D. - 25 Rectangular shape 500x500 mm precast R.C.C. manhole cover with frame - M.D. - 10 Circular shape 500 mm dia precast R.C.C. manhole cover with frame M.D. - 10 Circular shape 560 mm dia precast R.C.C. manhole cover with frame H.D. - 20 Circular shape 560 mm dia precast R.C.C. manhole cover with frame E.H.D. - 35 Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick plain type-I, medium density flat pressed three layer, graded particle board (FPT-I) as per IS:3087 bonded with BWP type synthetic resin adhesive, as per IS:848 Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick both sides prelaminated type-I, medium density flat pressed three layer, graded particle board (FPT-I) as per IS:3087 bonded with BWP type synthetic resin adhesive, as per IS:848 Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick one side prelaminated type-I, and other side balancing lamination, medium density flat pressed three layer, graded particle board (FPT-I) as per IS:3087 bonded with BWP type synthetic resin adhesive, as per IS:848
Unit
Rate
each each each each each each each each each each each each each each
26.00 28.00 685.00 975.00 1,400.00 170.00 225.00 690.00 600.00 560.00 660.00 630.00 1,030.00 1,150.00
sqm
1,780.00
7139
sqm
1,930.00
7143
sqm
1,850.00
33
Description Factory made 30 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of sheet glass using 10 kg/ sqm glass panes Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm Factory made 30 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm Laminated veneer lumber confirming to TADS 15:1995 manufactured in factory in frames of doors, windows C.I. pile shoe M.S. clamps for pile shoe Bentonite Oxidised M.S. safety chain (weighing not less than 450 gms) for door C.I. grating 150 mm dia, weighing not less than 440 gm uPVC pipes (working pressure 4 kg / cm 2 ) Single socketed pipe 75 mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Single socketed pipe 110 mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Rubber (Seal) Ring 75 mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Rubber (Seal) Ring 110 mm dia uPVC coupler for uPVC drainage pipes 75 mm uPVC coupler for uPVC drainage pipes 110 mm uPVC pushfit coupler (single) 75 mm thick uPVC pushfit coupler (single) 110 mm thick uPVC single equal Tee (without door) 75x75x75 mm uPVC single equal Tee (without door) 110x110x110 mm uPVC single equal Tee (with door) 75x75x75 mm uPVC single equal Tee (with door) 110x110x110 mm
Unit
Rate
sqm
1,580.00
7154
sqm
1,630.00
7155
sqm
1,385.00
7157
metre
67.00
7189
metre
129.00
7190
each
16.00
7191
34
Code No. 7208 7209 7212 7213 7214 7215 7231 7232 7233 7236 7237 7239 7240 7241 7244 7245 7246
Description uPVC bend 87.5 , 75 mm bend uPVC bend 87.5 , 110 mm bend uPVC plain shoe 75 mm bend uPVC plain shoe 110 mm bend uPVC pipe clip 75 mm bend uPVC pipe clip 110 mm bend Resin Bonded Glass wool 16 kg/m 50 mm thick Resin Bonded Glass wool 24 kg/m 50 mm thick Fibre glass tissue reinforcement Type II Grade I Precast chequered cement tiles 22 mm thick Dark shade using ordinary cement Precast chequered cement tiles 22 mm thick medium shade using 50% white cement, 50% ordinary cement Epoxy paint Fire retardant paint Melamine polish Table rubbed polished stone 18 mm thick (75x50cm) Agaria Marble stone - 18 mm thick Table rubbed polished stone 18mm thick (75x50cm) Granite stone 18mm thick Vertical load testing (INITIAL) of piles in accordance with IS : 2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification and up to 50MT capacity pile Vertical load testing (INITIAL) of piles in accordance with IS : 2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & above 50MT and up to 100MT Vertical load testing (INITIAL) of piles in accordance with IS : 2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & group of two or more up to 50MT Cyclic vertical load testing of piles in accordance with IS : 2911 (PartIV) including preparation of pile head etc. for Single pile up to 50 tonne capacity Cyclic vertical load testing of piles in accordance with IS : 2911 (PartIV) including preparation of pile head etc. for Single pile above 50 tonne capacity pile and up to 100 tonnecapacity pile
0 0
Unit each each each each each each sqm sqm sqm sqm sqm litre litre litre sqm sqm
Rate 56.00 95.00 107.00 207.00 16.00 31.00 145.00 204.00 65.00 230.00 360.00 315.00 350.00 250.00 1,630.00 1,825.00
per test
33,200.00
7247
per test
40,300.00
7248
per test
48,500.00
7249
per test
15,000.00
7250
per test
23,000.00
35
Description Cyclic vertical load testing of piles in accordance with IS : 2911 (Part- IV) including preparation of pile head etc. for Group of two piles up to 50 tonne capacity each Lateral load testing of single pile in accordance with IS : 2911 part IV for determining safe allowable lateral load on pile. Up to 50 tonne capacity Lateral load testing of single pile in accordance with IS : 2911 part -IV for determining safe allowable lateral load on pile. Above 50 tonne capacity Hardening compound Road marking paint (spirit based) Superior quality road marking paint (water based) C.P. Brass bibcock 15 mm C.P. Brass long nose bibcock 15 mm C.P. Brass long body bibcock 15 mm C.P. Brass stop cock (concealed) 15 mm C.P. Brass angle valve 15 mm Pressed clay tiles 20 mm thick 250 x 250 mm size Plain ceiling tiles (BWP type phenol formaldehyde synthetic resin bonded) (600x600x12 mm) Semi perforated ceiling tiles (600x600x12 mm) 25 mm thick particle board 30 mm thick prelaminated flush door shutter IInd class teak wood lipping 25 mm wide x 12 mm thick 25 mm thick melamine faced prelaminated three layer particle board Granite of any colour, 18 mm thick (slab area upto 0.50 sqm) Granite of any colour, 18 mm thick (slab area above 0.50 sqm) Aluminium T or L sections For flush door shutters Extra for providing teak veneering on one side instead of commercial veneering Paving Asphalt of grade VG-30 of approved quality Expandable fastener with plastic sleeve and M.S. screws, 25 mm long Expandable fastener with plastic sleeve and M.S. screws, 32 mm long Expandable fastener with plastic sleeve and M.S. screws, 40 mm long
Unit
Rate
per test
29,500.00
7252
per test
15,000.00
7253
per test litre litre litre each each each each each 1,000 nos each each sqm sqm metre sqm sqm sqm kilogram sqm tonne each each each
23,500.00 37.00 120.00 170.00 325.00 330.00 350.00 350.00 370.00 12,150.00 120.00 120.00 460.00 850.00 39.00 870.00 1,550.00 1,640.00 220.00 320.00 38,500.00 8.00 9.00 12.00
7254 7255 7256 7257 7258 7259 7260 7261 7266 7267 7268 7269 7270 7271 7272 7295 7297 7306 7307 7309 7312 7313 7314
36
Code No. 7315 7318 7319 7320 7321 7322 7323 7324 7325 7326 7327 7328 7329 7330 7331 7332 7333 7334 7335 7338 7339 7340 7342 7343 7344 7345 7346 7347 7348 7349 7354 7358 7359 7361 7363 7364 7366
Description Expandable fastener with plastic sleeve and M.S. screws. 50 mm long Plasticizer / super plasticizer Wall form panel 1250x500 mm Tie bolt 12 mm dia 100 mm length Tie bolt 12 mm dia 150 mm length Tie bolt 20 mm dia 150 mm length Tie bolt 20 mm dia 225 mm length Spring coil 12 mm Plastic cone 12 mm dia Corner angle 45x45x5 mm 1.50 m long 100 mm channel shoulder 2.5 m long Double clip ( bridge clip) Single clip M.S. tube 40 mm dia Wall form panel 1250x450 mm Corner angle 45x45x5 mm 2.50 m long Column clamp 450x1070 mm Prop 2 m ( 2-3.5m) Binding wire Gun metal cramp Stainless steel cramp Stainless steel pin Adjustable span ESO+SI (2.35-3.40) Adjustable telescopic prop 3 m (2.02-3.75 m) Beam clamp 300-380 mm (450-1070 mm) Prop 4 m Double coupler Cadmium plated full threaded steel screws (30x4 mm dia.) Aluminium washer 2 mm thick 15 mm dia 12 mm M.S. U beading Plastic encapsulated M.S. foot rest 30x20x15 cm Flushing Cistern P.V.C. 10 lts capacity ( low level ) (White) ( with fittings, accessories and flush pipe) P.V.C. automatic flushing cistern 5 lts capacity P.V.C. automatic flushing cistern 10 lts capacity 15 mm C.P. brass tap with elbow operation lever White glazed fire clay draining board 600x450x25 mm Glass reinforced Gypsum (GRG) board 12.5 mm thick
Unit each kilogram each each each each each each each each each each each metre each each each each kilogram kilogram kilogram kg each each each set each each 100 nos 100 nos metre each each each each each each sqm
Rate 14.00 36.50 1,050.00 38.00 50.00 62.00 80.00 16.00 18.00 300.00 1,160.00 97.00 77.00 280.00 1,040.00 340.00 1,220.00 830.00 53.00 305.00 320.00 180.00 1,825.00 1,150.00 422.00 1,170.00 55.00 28.00 10.00 14.00 110.00 640.00 490.00 530.00 600.00 525.00 230.00
37
Code No. 7367 7369 7375 7376 7377 7378 7379 7380 7381 7382 7385 7386 7387 7388 7389 7390 7391 7392 7393 7394 7395 7396 7397 7398 7399 7400 7401 7402 7403
Description Galvanised M.S. sheet 0.5 mm thick pressed channel section of size 50x32 mm Galvanised M.S. sheet 0.50 mm thick pressed stud. 48x34x36 mm G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Single lipped urinal G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of two lipped urinals G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of three lipped urinals G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of four lipped urinals White vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per IS : 2556 Precast R.C.C. grating with frame 500x450 mm horizontal grating Precast R.C.C. grating with frame 450x100 mm vertical grating Bitumen emulsion rapid setting (R.S.) confirming to IS : 8887 3 mm thick translucent white acrylic plastic sheet 12 mm thick particle board ceiling tile Spigot for standard jointing Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt Anodising 15 microns on aluminium sections Neoprene/EPDM rubber gasket Anodising 25 microns on aluminium sections Powder coating 50 microns on aluminium sections Polyester powder coating 50 microns on aluminium sections Double action hydraulic floor spring with stainless steel cover plate 6 mm dia. G.I. adjustable hangers including clips (up to 1.2 m length) Double action hydraulic floor spring with brass cover plate Base Jack Challies Cup locks 15 mm PTMT bib cock 15 mm PTMT bib cock with flange (fancy) 15 mm PTMT bib cock long body with flange 15 mm dia PTMT stop cock(male thread)
Unit
Rate
metre metre each each each each each each each tonne sqm sqm kilogram each kilogram metre kilogram kilogram kilogram each each each each each each each each each each
60.00 72.00 440.00 1,010.00 1,240.00 1,800.00 1,440.00 650.00 305.00 27,700.00 570.00 260.00 45.00 48.00 40.00 25.00 50.00 64.00 70.00 1,525.00 28.00 1,675.00 180.00 800.00 75.00 100.00 140.00 160.00 100.00
38
Code No. 7405 7406 7407 7408 7409 7410 7411 7412 7415 7416 7417 7418 7419 7420 7421 7422 7423 7424 7425 7426 7427 7428 7429 7430 7431 7432 7439 7442 7443 7444 7445 7449 7451 7452 7453 7466
Description 20 mm dia. PTMT stop cock PTMT pillar cock PTMT push cock 15 mm dia PTMT push cock 12 mm dia 20 mm BSP PTMT grating 100 mm dia PTMT Pillar cock (fancy) 15mm foam flow 125 mm grating with waste hole Rectangular type with openable circular lid 150 mm size 18 mm high with 100 mm dia (110 gm) Double acting air valve 50 mm Double acting air valve 80 mm Double acting air valve 100 mm Water meter (including testing charges) 80 mm Water meter (including testing charges) 100 mm Water meter (including testing charges) 150 mm Water meter (including testing charges) 200 mm Dirt box strainer 80 mm Dirt box strainer 100 mm Dirt box strainer 150 mm Dirt box strainer 200 mm Cat's eye Water stops Serrated with central bulb (225 mm wide, 8-11 mm thick) Water stops Dumb bell with central bulb Kickers Wedge expansion hold fastener 1/4" or 6 mm Wedge expansion hold fastener 3/8" or 10 mm Wedge expansion hold fastener 1/2" or 12 mm 8 mm thick (mirror polished tiles machine cut edge) Raj Nagar white Wheel 75 mm dia. 40 mm wide Aluminium single cleat of size 30x32x3 mm Aluminium grip strip of size 50x12x2 mm 25 mm thick prelaminated flush door shutter both side decorative Aluminium U beading Glass sheet (Pin headed) 4 mm thick Raj nagar plain white marble (table rubbed and polished) 18 mm thick (slab area upto 0.50 sqm) Raj nagar plain white marble (table rubbed and polished) 18 mm thick (slab area more than 0.50 sqm) Second class deodar teak wood lipping 30 mm wide x 12 mm thick
Unit each each each each each each each each each each each each each each each each each each each each metre metre metre each each each sqm each each each sqm kilogram sqm sqm sqm metre
Rate 130.00 160.00 90.00 80.00 31.00 225.00 37.00 101.00 3,370.00 4,930.00 6,400.00 2,030.00 3,150.00 4,560.00 5,100.00 2,620.00 4,180.00 5,420.00 7,550.00 180.00 390.00 351.00 360.00 12.00 14.00 26.00 480.00 60.00 13.00 10.00 790.00 208.00 255.00 610.00 680.00 30.00
39
Description Veneered particle board with commercial veneering on both sides 12 mm thick Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade)12 mm thick Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade)18 mm thick Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade)25 mm thick Prelaminated particle board with both sides decorative lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade)12 mm thick Oxidised M. S. hinges finished with nickel plating 50 mm (Over all width) Oxidised M. S. hinges finished with nickel plating 65 mm (Over all width) PTMT - Waste Coupling 31/32 mm PTMT - Waste Coupling 38/40 mm PTMT - Bottle Trap 31/32 mm PTMT - Bottle Trap 38/40 mm PTMT - Ball Cock 15 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 20 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 25 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 40 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 50 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Angle Stop cock with Flange 15 mm PTMT - Swiveling shower 15 mm PTMT - Liquid Soap Container of 400 ml capacity PTMT - Towel Ring 215x200x37 mm PTMT - Towel Rail (450 mm) PTMT - Towel Rail (600 mm)
Unit
Rate
sqm
480.00
sqm
690.00
7478
sqm
810.00
7479
sqm
880.00
7480
sqm metre metre each each each each each each each each each each each each each each each
720.00 39.00 49.00 51.00 64.00 317.00 345.00 134.00 195.00 420.00 780.00 1,150.00 130.00 87.00 145.00 116.00 192.00 226.00
7485 7486 7491 7492 7493 7494 7495 7496 7497 7498 7499 7500 7501 7503 7504 7505 7506
40
Code No. 7507 7508 7509 7512 7513 7514 7515 7516 7517 7518 7552 7553 7555 7556 7651 7652 7653 7654 7655 7656 7657 7658 7659 7660 7661 7662 7663 7664 7665 7666 7668 7669 7670 7671 7672 7673 7674 7675 7676
Description PTMT - Shelf 450x124x36 mm PTMT - Urinal Spreader 15 mm PTMT - Soap Dish/Holder 138x102x75 mm PTMT - handle 125x34x24 mm PTMT - handle 150x34x24 mm PTMT - butt hinges 75x60x10 mm PTMT - butt hinges 100x75x10 mm PTMT - Tower bolt 152x42x18 mm PTMT - Tower bolt 202x42x18 mm PTMT - door catcher 72x42 mm Coir veneered board 4 mm thick Coir veneered board 6 mm thick Coir veneered board 12 mm thick Coir veneered board 18 mm thick Ductile Iron class K - 9 pipe Conforming to I.S. 8329 100 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 150 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 200 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 250 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 300 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 350 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 400 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 450 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 500 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 600 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 700 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 750 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 800 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 900 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 1000 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 100 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 150 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 200 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 250 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 300 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 350 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 400 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 450 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 500 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 600 mm dia
Unit each each each each each each each each each each sqm sqm sqm sqm metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre each each each each each each each each each each
Rate 258.00 127.00 120.00 30.00 34.00 42.00 56.00 65.00 80.00 27.00 272.00 367.00 622.00 950.00 797.00 1,170.00 1,595.00 2,105.00 2,680.00 3,225.00 4,350.00 5,085.00 6,180.00 7,430.00 10,050.00 11,350.00 11,990.00 14,030.00 15,750.00 26.00 36.00 62.00 73.00 103.00 127.00 234.00 260.00 285.00 352.00
41
Code No. 7677 7678 7679 7680 7681 7682 7683 7684 7685 7686 7687 7688 7689 7690 7691 7692 7693 7694 7695 7696 7697 7698 7699 7700 7701 7702 7703 7704
Description Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 700 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 750 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 800 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 900 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 1000 mm dia Ductile Iron K - 12 specials suitable for push on jointing upto 600 mm dia Ductile Iron K - 12 specials suitable for push on jointing over 600 mm dia Ductile Iron specials suitable for mechanical jointing as per I.S. 9523 upto 600 mm dia Ductile Iron Specials suitable for mechanical jointing as per I.S. 9523 over 600 mm dia Ductile Iron Pipe Class K-9 flanges and welding 100 mm dia Ductile Iron Pipe Class K-9 flanges and welding 150 dia Ductile Iron Pipe Class K-9 flanges and welding 200 mm dia Ductile Iron Pipe Class K-9 flanges and welding 250 mm dia Ductile Iron Pipe Class K-9 flanges and welding 300 mm dia Ductile Iron Pipe Class K-9 flanges and welding 350 mm dia Ductile Iron Pipe Class K-9 flanges and welding 400 mm dia Ductile Iron Pipe Class K-9 flanges and welding 450 mm dia Ductile Iron Pipe Class K-9 flanges and welding 500 mm dia Ductile Iron Pipe Class K-9 flanges and welding 600 mm dia Ductile Iron Pipe Class K-9 flanges and welding 700 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 100 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 125 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 150 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 200 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 250 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 300 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 350 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 400 mm dia
Unit each each each each each quintal quintal quintal quintal metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre
Rate 542.00 636.00 684.00 915.00 1,138.00 11,850.00 16,280.00 12,540.00 17,580.00 2,025.00 2,825.00 3,740.00 4,935.00 6,330.00 8,020.00 9,645.00 11,675.00 13,895.00 18,760.00 23,275.00 830.00 1,040.00 1,240.00 2,120.00 2,830.00 3,740.00 4,500.00 5,870.00
42
Code No. 7705 7706 7707 7708 7709 7710 7711 7712 7713 7714 7715 7716 7717 7718 7719 7720 7721 7722 7723 7724 7725
Description S&S Centrifugally (Spun) C.I. Pipe class LA 450 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 500 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 600 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 suitable for lead jointing up to 300 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 suitable for lead jointing over 300 mm dia S&S Centrifugally (Spun) C.I. Pipe specials suitable for mechanical joint as per I.S. 13382 up to 300 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials suitable for mechanical joint as per IS 13382 over 300 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 100 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 150 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 200 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 250 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 300 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 350 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 400 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 450 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 500 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 600 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 100 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 150 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 200 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 250 mm dia
Unit metre metre metre quintal quintal quintal quintal metre metre metre metre metre metre metre metre metre metre metre metre metre metre
Rate 7,100.00 8,250.00 11,450.00 5,850.00 7,500.00 8,200.00 8,880.00 1,260.00 1,960.00 3,170.00 3,730.00 4,770.00 6,080.00 7,890.00 9,940.00 12,390.00 15,330.00 708.00 1,035.00 1,415.00 1,920.00
43
Code No. 7726 7727 7728 7729 7730 7731 7732 7733 7734 7735 7736 7737 7738 7739 7741 7742 7800 7801 7802 7803 7804 7805 7806 7807 7808
Description Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 300 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 350 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 400 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 450 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 500 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 600 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 700 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 800 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 900 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 1000 mm dia Extruded burnt flyash clay sewer bricks conforming to I.S 4885 Fly ash lime bricks (FALG Bricks) conforming to I.S. 12894 Calcium Silicate Bricks machine moulded confirming to I.S. 4139 Modified Bitumen Refinery produced CRMB - 55 Modified Bitumen Refinery produced CRMB - 60 Bitumen emulsion medium setting (M.S.) conforming to IS : 8887 Ceramic Glazed Tiles Ist quality minimum thickness 5mm in all colours shades and designs except burgundy, bottle green, black Ceramic Glazed Tiles Ist quality 300 x 300mm in all shades and designs of White, Ivory, grey, Fume Red brown etc. Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades designs except White, Ivory, Grey, Fume Red Brown etc. Rectified - Ceramic Glazed Tiles Ist quality 300 x 300 mm or more in all shades designs White, Ivory, Grey, Fume Red Brown etc Rectified - Ceramic Glazed Tiles Ist quality 300 x 300 mm or more in all shades designs except White, Ivory, Grey, Fume Red Brown etc. Salem Stainless steel AISI - 304 (18/8) Orrisa pattern W.C. pan 724 mm X 578 mm Salem Stainless steel AISI - 304 (18/8) Round basin 405 mm X355 mm Salem Stainless steel AISI - 304 (18/8) Wash basin 530 mm X 345 mm each Centrifugally cast (spun) iron S&S 100 mm inlet and 100 mm outlet
Unit metre metre metre metre metre metre metre metre metre metre 1000 nos 1000 nos 1000 nos toone tonne tonne sqm sqm sqm sqm sqm each each each each
Rate 2,638.00 3,135.00 3,714.00 4,411.00 5,214.00 6,801.00 8,739.00 11,156.00 14,617.00 15,485.00 3,900.00 3,300.00 3,600.00 38,500.00 38,800.00 28,200.00 295.00 360.00 367.00 510.00 535.00 3,630.00 1,690.00 1,470.00 392.00
44
Code No. 7809 7850 7857 7858 7859 7861 7862 7863 7864 7865 7866 7900 7901 7902 7903 7904 8001 8002 8003 8004 8006 8007 8008 8010 8011 8012 8100 8200
Description Centrifugally cast (spun) iron S&S 100 mm inlet and 75 mm outlet Agaria White marble slab plain 18 mm thick P.T.M.T. Grating square slit 150 mm P.T.M.T. Urinal cock 15mm dia P.T.M.T. Bib cock with nozzle 15 mm P.T.M.T. Stop cock (concealed) 15 mm 15 mm nominal bore and 30 cm length PVC connection pipe with P.T.M.T. Nuts 15 mm nominal bore and 45 cm length PVC connection pipe with P.T.M.T. Nuts P.T.M.T. extension nipple 15 mm P.T.M.T. extension nipple 20 mm P.T.M.T. extension nipple 25 mm Modular common burnt clay bricks of class designation 7.5
Unit each sqm each each each each each each each each each 1,000 nos
Rate 424.00 1,090.00 77.00 94.00 133.00 173.00 33.00 38.00 32.00 38.00 57.00 3,150.00 4,150.00 3,800.00 3,550.00 3,700.00 2,025.00 2,125.00 2,025.00 2,420.00 173.00 632.00 752.00 142.00 330.00 165.00 79.00 59.00
Machine moulded perforated common burnt clay FPS (non modular) bricks of class designation 12.5 1,000 nos Machine moulded common burnt clay modular perforated bricks of class designation 12.5 1,000 nos Machine moulded common burnt clay FPS (non modular) bricks of class designation 12.5 1,000 nos Machine moulded common burnt clay tile bricks of class designation 12.5 1,000 nos 24 mm thick Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish 30 mm thick Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish Factory made PVC rigid foam panelled shutter i/c carriage Factory made PVC rigid foam panelled shutter as per IS : 4020 i/c carriage Factory made PVC rigid foam sheet 1 mm thick Factory made PVC rigid foam sheet 5 mm thick Factory made prelaminated PVC rigid foam sheet 5 mm thick 48 mmX40 mmX1.5 mm thick Factory made door frame of PVC extruded sections in white, grey or wooden finish Factory made door frame PVC extruded sheet i/c carriage Adhesive solvent cement Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm A.P.P. modified polymeric felt (two layers) 1.5 mm thick sqm sqm sqm sqm sqm sqm sqm metre metre kg 10 nos sqm
45
Code No. 8201 8203 8204 8205 8206 8207 8210 8211 8212 8214 8215 8216 8217 8218 8219 8220 8221 8222 8223 8224 8225 8300 8301 8302 8303 8304 8305 8501 8502 8504
Description A.P.P. modified polymeric felt (two layers) 2 mm thick A.P.P. modified 2 mm thick membrane reinforced with glass fibre matt A.P.P. modified 3 mm thick membrane reinforced with glass fibre matt A.P.P. modified 3 mm thick membrane reinforced with polyester matt Bitumen primer for bitumen membrane Geotextile 120 gram per sqm membrane Stainless steel screws 50 mm Stainless steel screws 40 mm Stainless steel screws 30 mm Stainless steel screws 20 mm Stainless steel butt hinges 125x64x1.9 mm IS : 12817 marked Stainless steel butt hinges 100x58x1.9 mm IS : 12817 marked Stainless steel butt hinges 75x47x1.8 mm IS : 12817 marked Stainless steel butt hinges 50x37x1.5 mm IS : 12817 marked Stainless steel butt hinges (heavy weight) 125x64x2.5 mm IS : 12817 marked Stainless steel butt hinges (heavy weight) 100x60x2.5 mm IS : 12817 marked Stainless steel bult hinges (heavy weight) 75x50x2.5 mm IS : 12817 marked M.S. heavy weight but hinges 125x90x4.0 mm IS : 1341 marked M.S. heavy weight butt hinges 100x75x3.5 mm IS: 1341 marked M.S. heavy weight butt hinges 75x60x3.1 mm IS: 1341 marked M.S. heavy weight butt hinges 50x40x2.5 mm IS : 1341 marked 1216 mm PE-AL-PE Composite pressure pipe 1620 mm PE-AL-PE Composite pressure pipe 2025 mm PE-AL-PE Composite pressure pipe 2532 mm PE-AL-PE Composite pressure pipe 3240 mm PE-AL-PE Composite pressure pipe 4050 mm PE-AL-PE Composite pressure pipe Polymer modified cementation coating Fibre glass cloth Multi surface paint
Unit sqm sqm sqm sqm litre sqm 100 nos 100 nos 100 nos 100 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos metre metre metre metre metre metre kilogram sqm litre
Rate 99.00 167.00 207.00 245.00 71.00 32.00 240.00 195.00 145.00 95.00 240.00 215.00 145.00 125.00 320.00 230.00 195.00 320.00 160.00 83.00 70.00 90.00 111.00 143.00 193.00 310.00 335.00 127.00 39.00 272.00
46
Code No. 8505 8506 8507 8508 8509 8510 8611 8612 8613 8614 8615 8616 8617 8618 8620 8621 8622 8623 8625 8626 8627 8628 8629 8630 8631 8632 8633 8634 8635 8636 8637
Description Acrylic exterior paint Premium Acrylic exterior paint Textured exterior paint Primer for cement paint Special Primer (C.W.) Metal Primer (U.G.) Main T ceiling sections 24x38x0.3 mm (3 metre long) Perimeter wall angle 24 x 24 x 0.3 mm (3 metre long) Intermediate cross T-Section 24x25x0.3 mm (1.2 mtr long) Intermediate cross T-Section 24x25x0.3 mm (0.6 mtr. long) Hanger rod 4 mm thick Adjustment clip 85x30x0.8 mm Soffit cleat (Size 27x37x25x1.60 mm) Dash fastener 6 mm dia 50 mm long Vitrified floor tile 50x50 cm Vitrified floor tile 60x60 cm Vitrified floor tile 80x80 cm Vitrified floor tile 100x100 cm Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - 16 mm Outer dia Poly propylene - Random - Co - Polymer (PPR) pipes SDR 7.4 -20 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 - 25 mm outer dia Poly propylene - Random - Co - poymer (PPR) pipes SDR 7.4 - 32 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -40 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -50 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -63 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -75 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -90 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR - 11 - 110 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR - 11- 160 mm Outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 15 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 20 mm outer dia
Unit litre litre litre litre litre litre each each each each each each each each sqm sqm sqm sqm metre metre metre metre metre metre metre metre metre metre metre metre metre
Rate 130.00 230.00 198.00 63.00 83.00 107.00 187.00 118.00 72.00 34.00 7.00 6.00 3.00 11.00 735.00 865.00 1,070.00 1,630.00 32.00 50.00 76.00 124.00 196.00 286.00 445.00 640.00 1,020.00 1,070.00 2,255.00 51.00 63.00
47
Code No. 8638 8639 8640 8641 8642 8643 8644 8645 8646 8647 8648 8649 8650 8651 8652 8653 8654 8655 8656 8657 8658 8659 8660 8661 8662 8663
Description Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 32 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 40 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 50 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 75 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 100 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 150 mm inner dia Silicon sealant Stainless steal screws 30 mm x4 mm Hermetically sealed double glazed unit made with 6 mm thick clear float glass both side having 12 mm air gap Stainless steel (SS 304 grade) adjustable friction window stay 205 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay 255 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay 355 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay. 510 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay. 710 x 19 mm Masking tape Autoclaved aerated cement (AAC) blocks Gypsum panel 666 X 500 X 100 mm size Bonding plaster for Gypsum panel Mechanised Autoclaved fly ash sand lime non modular bricks Water proof ply 12 mm thick Aluminium casement window fastener (Anodised AC 15 ) Aluminium casement window fastener (powder coated ) Aluminium casement window fastener (polyester powder coated) Aluminium round shape handle (anodised AC 15)
Unit metre metre metre metre metre metre metre metre cartridge 100 nos sqm each each each each each metre cum sqm kg 1,000 nos sqm each each each each
Rate 90.00 120.00 170.00 280.00 835.00 1,185.00 1,640.00 2,870.00 307.00 29.00 2,290.00 168.00 189.00 236.00 437.00 793.00 1.55 2,025.00 455.00 53.00 4,300.00 645.00 40.00 41.00 42.00 49.00
48
Code No. 8664 8665 8666 8667 8668 8669 8670 8671 8672 8673 8674 8675 8676 8677 8678 8683 8684 8685 8686 8687 8688 8689 8690 8691 8692 8693 8694 8695 8696
Description Aluminium round shape handle (powder coated) Aluminium round shape handle (polyester powder coated) Stainless steel screws 25 mm x 4 mm UV stabilised 2 mm thick plain FRP sheet UV stabilised 2 mm thick corrugated FRP sheet Mangalore ridge tiles 20 mm thick Mangalore tiles 20 mm thick Precoated galvanised iron profile sheet 0.50 mm TCT Precoated galvanised steel plain ridges Precoated galvanised steel flashings / aprons Precoated galvanised steel gutter Precoated galvanised steel north light curves Precoated galvanised steel barge board Precoated galvanised steel crimp curve 1 mm thick 35 mm wide bright finished stainless steel piano hinges Red sand stone gang saw cut 30 mm thick White sand stone gang saw cut 30 mm thick Delineator Precast C.C. Kerb stone M - 25 Thermoplastic paint Glass beads Interlocking C.C. paver block ( 60 mm thick, M-30 ) High intensity retro - reflective sheet Punched tape concertina coil 600 m dia. 10m openable length (Total length 90m) RBT reinforced barbed wire Turn buckle and strengthening bolt Precast pavement slab 450 x 450 x 50 mm (M - 30) Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm, PVC coated to outer dia 5 mm
Unit each each cent sqm sqm each each sqm metre metre metre metre metre sqm metre sqm sqm each cum kg kg sqm sqm bundle metre each set each sqm sqm
Rate 54.00 59.00 32.00 465.00 538.00 29.00 10.20 435.00 440.00 440.00 455.00 455.00 445.00 475.00 37.00 400.00 435.00 310.00 4,025.00 63.00 62.00 325.00 1,525.00 730.00 8.50 40.00 55.00 258.00 285.00
49
Code No. 8697 8698 8699 8700 8703 8704 8705 8706 8707 8708 8710 8711 8713 8714 8715 8716 8717 8719 8720 8721 8722 8723 8724 8725 8726 8727 8730 8731 8732 8733
Description Chain link fabric fencing mesh of size 25x25 mm made of G.I. wire of dia 3 mm Stainless steel cramps (weight 260 grams) with nuts, bolts and washer for dry stone cladding 8 mm thick tapered edge calcium silicate board 10 mm thick calcium silicate board Telescopic drawer channels 300 mm long Stainless steel roller for sliding arrangement in racks/ cupboards/ cabinets shutter 50 mmX42 mmX2 mm thick Factory made door frame of PVC extruded sections in white, grey or wooden finish 25 mm thick factory made PVC flush door shutter i/c carriage Factory made glass reinforced plastic door frame 90x45 mm i/ c carriage 30 mm thick factory made glass fiber reinforced plastic panel door shutter i/c carriage Factory made solid PVC door frame 60 x 30 mm i/c carriage 28 mm factory made solid PVC panel door shutter i/c carriage Fiber glass reinforced plastic chajja Magnetic catcher triple strip vertical type Magnetic catcher double strip horizontal type 100 mm mortice lock with 6 levers for aluminium door 12.5 mm thick Glass fibre reinforced Gypsum board 2nd class teak wood lipping/ moulded beading or Taj beading of size 18X5 mm Ceiling sections 0.55 mm thick having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm Perimeter channel having one flange of 20mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm Nylon sleeves & wooden screws (40 mm) Counter sunk ribbed head screw 25 mm 12 mm thick marine plywood conforming to IS:710 12 mm thick fire retardant plywood conforming to IS: 5509 1.5 mm thick decorative laminated sheet 1.0 mm thick decorative laminated sheet 30 mm thick factory made glass fiber reinforced plastic flush door shutter i/c carriage High polymer modified quickset tile adhesive Synthetic ployster triangular fibre of length 12 mm, effective diameter 10-40 microns and specific gravity of 1:34 to 1:40 Synthetic ployster triangular fibre of length 6 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40
Unit
Rate
sqm each sqm sqm set each metre sqm metre sqm metre sqm sqm each each each sqm metre metre metre each cent sqm sqm sqm sqm sqm per kg kg kg
340.00 84.00 223.00 370.00 135.00 8.00 135.00 2,050.00 365.00 1,715.00 270.00 2,120.00 3,460.00 15.00 12.00 310.00 160.00 25.00 39.00 25.00 1.90 72.00 825.00 860.00 475.00 350.00 1,975.00 16.00 365.00 365.00
50
Code No. 9999 0303 0801 0802 0803 0804 0805 0806 0807 0808 0824 1011 1182 1200 1204 2393 2394 2395 2396 2397 2398 2408 2413 2414 2506
Description Sundries NEW CODES Cowdung Silicon and acrylic emulsion Acrylic distemper 1st quality , having VOC content less than 50 gm/litre Acrylic emulsion , having VOC content less than 50 gm/litre Premium acrylic emulsion of interior grade, having VOC content less than 50 gm/litre Synthetic enamel paint , having VOC (Volatile Organic Compound) content less than 150 gm/litre Ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 gms/litre Ready mixed red oxide zinc chromatic on steel/ iron work, having VOC content less than 250 gms/litre Water thinnable cement primer for interior wall surface, having VOC content less than 50 gms/litre Cement base wall care putty Steel glazed door,window/ ventilator, all members viz. F7D, F4B, K11 and K12B etc. Surkhi Kiln seasoned selected sheesham wood planks Precast heat resistant terrace tiles (size 300x300 mm) and 20 mm thick 1 mm thick Stainless Steel Cover plate grade 304 Coupler 16 mm dia Coupler 20 mm dia Coupler 25 mm dia Coupler 28 mm dia Coupler 32 mm dia Float glass sheet of nominal thickness 8 mm (weight not less than 20.00 kg/ sqm) 12 mm commercial ply 18 mm thick block board with commercial ply veneering on both side
Unit L.S. cum litre Kg litre litre litre litre litre litre kg kg cum 10 cudm sqm kg each each each each each sqm sqm sqm
Rate 1.49 47.00 140.00 38.00 200.00 350.00 180.00 103.00 125.00 55.00 23.50 48.00 700.00 650.00 482.00 275.00 67.50 87.75 129.50 191.25 230.50 700.00 580.00 700.00
Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x 60 mm 10 nos Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x 80 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x 120 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x 140 mm
250.00
2507
10 nos
293.00
2508
10 nos
364.00
2509
10 nos
425.00
51
Description Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x 160 mm Truf Paver (500 x 500 x 40 mm) Ceremic Tiles Pieces for Crazy Flooring 15 mm Battery Based Sensor Pillar Cock Stainless steel (Grade-304)hollow section round/square tubes Stainless steel bolts/square bar and plates 12.5 mm thick Fully Perforated gypsum board 12.5 mm thick tapered edge gypsum fire resistant board 12.5 mm thick tapered edge gypsum moisture resistant board PU Primer 40 mm (average) PU spray having 40-45 kg/m3 density GI wire netting 3/4" x 24 G 400 G polythene sheet Wall mounted water closet Adjustable Vetrious China Cistern with fittings White Vetrious China Waterless Urinal Cistern with fittings for Waterless Urinal White Vetrious Urinal Chemical ASTMC-type I Waste plastic additive Chemical ASTMC-type II M.S. pipe 150 mm dia casing pipe M.S. pipe 200 mm dia casing pipe PVC blind pipe 150 mm dia as per IS: 12818 PVC blind pipe 200 mm dia as per IS: 12818 M.S. cap 150 mm dia M.S. cap 200 mm dia M.S bail plug 150 mm dia M.S bail plug 200 mm dia PVC slotted pipe 150 mm dia as per IS: 12818 PVC slotted pipe 200 mm dia as per IS: 12818 Boulder 50 mm to 200 mm Gravel 5 mm to 10 mm Gravel 1.5 mm to 2 mm Gravel 3 mm to 6 mm M.S. pipe 100 mm dia casing pipe uPVC blind pipe 100 mm dia as per IS: 12818
Unit
Rate
10 nos sqm quintal each kg kg sqm sqm sqm sqm sqm sqm sqm each each each each each kg tonne kg metre metre metre metre each each each each metre metre cum cum cum cum metre metre
560.00 1,080.65 130.00 5,822.50 325.00 120.00 927.00 237.00 271.00 40.75 419.40 26.25 15.00 4,548.00 2,409.60 13,208.00 3,029.60 12,592.75 100.00 40,000.00 160.00 1,042.00 1,250.00 460.00 834.75 150.00 180.00 170.00 200.00 465.15 840.00 332.00 650.00 625.00 650.00 750.00 385.00
2708 2709 3327 4001 4002 7028 7030 7031 7050 7051 7052 7053 7072 7073 7074 7075 7076 7178 7280 7281 7743 7744 7745 7746 7747 7748 7749 7750 7751 7752 7753 7754 7755 7756 7757 7758
52
Code No. 7759 7760 7761 7762 7763 7764 7765 7766 7767 7768 7769 7770 7771 7772 8014 8589 8590 8591 8592 8593 8594 8595 8597 8598 8599 8600 8601 8602 8604 8605 8606
Description uPVC slotted pipe 100 mm dia as per IS: 12818 M.S. cap 100 mm dia M.S. bail plug 100 mm dia Precast R.C.C. perforated slab Water supply tanker of 5000 litre capacity M.S. socket 100 mm dia M.S. socket 150 mm dia M.S. socket 200 mm dia Stone cleaning chemical approved by ASI Water repallent chemical approved by ASI Stone surface strengthening chemical approved by ASI Turpentine oil Liquid Amonia 5% Pea Gravel Factory made door frame of size 50x47 mm with wall thickness 5 mm made of single piece extruded profile Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm thick Galvanised Steel main Tee ceiling section Size 24 x 38 x 0.33 mm (3 metre long) Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm (3.00 metre long) Galvanised Steel intermediate cross T section Size 24 x 25 x 0.33 mm (1.2 metre long) Galvanised Steel intermediate cross T section Size 24 x 25 x 0.33 mm ( 0.6 metre long) Galvanised Steel soffit cleat size 25x35x1.60 mm Wooden screws with plastic rawl plugs 35x8 mm GI Metal Tile Clip in Plain Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick GI Metal Tile Clip in Perforated Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick GI Metal Tile Lay-in Plain Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick GI Metal Tile Lay-in Perforated Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm and 12.5 mm thick Gypsum Tiles Fully Perforated Square edge of Size 595x595 mm and 12.5 mm thick Spring T-section 24x34x0.45 mm (3.00 meter long) C Wall angle section 20x30x20x0.50 mm (3.00 meter long) Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long)
Unit metre each each each each each each each litre litre litre litre litre cum Meter sqm each each each each each each sqm sqm sqm sqm sqm sqm meter meter meter
Rate 390.00 120.00 140.00 750.00 600.00 165.00 200.00 250.00 164.01 1,586.25 1,017.17 67.50 160.80 650.00 450.00 858.00 192.00 125.00 77.00 39.00 3.00 0.55 894.00 998.00 809.00 906.00 468.00 484.00 180.00 155.00 164.00
53
Code No. 8607 8608 8609 8610 8682 8709 8712 8734 8735 8736 8737 8738
Description Spring T-connector C Carrier Connector C Suspension Clip Wire Coupling Clip Epoxy Grout 30 mm thick factory made solid PVC profile panelled door single piece extruded profile decorative finish (wood grain printed on both side) 30 mm thick factory made solid PVC profile panelled door single piece extruded profile non decorative finish P.V.C. Single piece extruded door frame of profile size 50 mm x 47 mm with wall thickness of 5 mm 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished) 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile decorative finished (Wood grain finished) Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50 mm dia wire Factory made door frame fire rated ( 60 minutes) made with 16 SWG G.I. Sheet of section 143 mm x 57 mm duly filled with vermuculite based concrete mix Fire rated door shuttere made with 16 SWG G.I. sheet (60 minutes) without panel Fire seal Putty Clear fire resistant glass panes 6mm thick (60 minutes) G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/m 2) with ceramic tape of suitable thickness and fire resistant primer coating Matrix Mineral Board Panic Bar / latch (Double point) 65 mm x 55 mm x 2 mm thick Factory made door frame of PVC extruded section in white,grey or wooden finish 37 mm thick Factory made shutter with style,rails and panels of PVC extruded section in white or grey finish i/c carriage 75 mm x 53 mm x 2.0 mm thick Factory made door frame of PVC extruded section in white,grey or wooden finish 37 mm thick Factory made fusion welded shutter with style, rails and panels of PVC extruded section in wooden finish Zinc alloy (white powder coated) casement handle for uPVC windows Zinc alloy (white powder coated) Touch Lock for uPVC windows Zinc alloy rollers for uPVC windows Zinc alloy rollers for uPVC door Zinc alloy (white powder coated) casement lock for uPVC windows
Unit each each each each Kg sqm sqm metre sqm sqm sqm
Rate 5.00 11.00 11.00 9.00 500.00 2,500.00 2,120.00 340.00 2,088.00 2,536.00 760.00
metre metre each metre sqm metre sqm each each each each each
247.00 61.85 5,000.00 318.00 2,225.00 327.00 2,300.00 150.00 100.00 50.00 80.00 100.00
8743 8744 8745 8746 8747 8748 8750 8751 8752 8753 8754
54
Code No. 8755 8756 8757 8758 8759 8760 8761 8762 8763 8764 8765 8766 8767 8768 8769 8770 8771 8772 8773 8774 8775 8776 8778
Description Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 300 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 350 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 400 mm x 19 x 1.9 mm for uPVC windows uPVC extruded profile casement window Frame (50 mm x 50 mm) uPVC extruded profile casement window sash (Style and Rail) (62 mm x 34 mm) uPVC extruded profile casement window mullion (intermediate section) (66 mm x 50 mm) uPVC extruded profile casement window 'T' profile (one vertical length in between two shutters) (24 mm x 34.5 mm) uPVC extruded profile casement window glazing bead (12 mm x 18 mm) uPVC extruded profile casement window Frame ( 67 mm x 62 mm) uPVC extruded profile casement Window Sash/Mullion ( 67 mm x 75 mm) (Style,rail and intermediate section) uPVC extruded profile casement window glazing bead (35 mm x 18 mm) uPVC extruded profile Two Track Sliding frame (67 mm x 52 mm) uPVC extruded profile Sliding window Sash (60 mm x 44 mm) uPVC extruded profile Sliding Interlock for Window (one vertical length in each shutter) (45.5 mm x 28 mm) uPVC extruded profile Sliding Door Sash (80 mm x 44 mm) Aluminium Track on bottom rail for uPVC window Wool Pine for uPVC window Aluminium Grill Steel Galvanised tubular reinforcement for uPVC door/ window Stainless steel dash fastener of 8 mm dia and 75 mm long bolt Toughened glass 12 mm thickness
Unit
Rate
each each each each each metre metre metre metre metre metre metre metre metre metre metre metre metre metre kg metre each sqm
225.00 275.00 350.00 400.00 500.00 158.00 145.00 175.00 46.00 46.00 225.00 250.00 78.00 235.00 212.00 45.00 275.00 20.00 15.00 250.00 50.00 20.00 1,800.00
55
56
Code No. 2275 2281 2287 2290 2299 2302 2303 2308 2309 2311 2314 2317 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2341 2342 2343 2344 2345 2346 2347
Description R.C.C. pipes 100 mm dia R.C.C. pipes 150 mm dia R.C.C. pipes 250 mm dia R.C.C. pipes 300 mm dia R.C.C. pipes 450 & 500 mm dia G.I.sheet and accessories R.C.C. pipes 600, 700, 750 & 800 mm dia Plaster of paris Cast iron fittings Red bajri Barbed wire Sludge Spun iron S & S pipes 100 mm dia Spun iron S & S pipes 125 mm dia Spun iron S & S pipes 150 mm dia Spun iron S & S pipes 200 mm dia Spun iron S & S pipes 250 mm dia Spun iron S & S pipes 300 mm dia Spun iron S & S pipes 350 mm dia Spun iron S & S pipes 400 mm dia Spun iron S & S pipes 450 mm dia Spun iron S & S pipes 500 mm dia Spun iron S & S pipes 600mm dia C.I. pipes 500 mm dia R.C.C. pipes 900 mm dia R.C.C. pipes 1000 mm dia R.C.C. pipes 1100 mm dia R.C.C. pipes 1200 mm dia Jamuna sand Pig lead Solvent/ Diesel Ductile iron pipes (k7) 100 mm dia Cast iron pipes 150 mm dia Cast iron pipes 200 mm dia Cast iron pipes 250 mm dia Cast iron pipes 300 mm dia
Unit 100 metre 100 metre 100 metre 100 metre 100 metre tonne 100 metre tonne tonne cum tonne cum 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre cum tonne quintal 100 metre 100 metre 100 metre 100 metre 100 metre
Rate 191.48 319.12 737.68 911.78 2,127.50 77.87 3,191.25 77.87 77.87 87.60 77.87 95.22 191.48 255.77 319.12 519.11 737.68 911.78 1,276.50 1,740.68 2,127.50 2,127.50 3,191.25 2,127.50 4,786.87 6,382.50 6,382.50 6,382.50 87.60 77.87 8.76 191.48 319.12 519.11 737.68 911.78
57
Code No. 2348 2349 2350 2351 2352 2353 2355 2356 2357
Description Cast iron pipes 350 mm dia Cast iron pipes 400 mm dia Cast iron pipes 450 mm dia Cast iron pipes 500 mm dia Cast iron pipes 600 mm dia Cast iron pipes 700 mm dia Cast iron pipes 800 mm dia Cast iron pipes 900 mm dia Cast iron pipes 1000 mm dia
Unit 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre
Rate 1,276.50 1,740.68 2,127.50 2,127.50 3,191.25 3,191.25 3,191.25 4,786.87 6,382.50
58
CARRIAGE OF MATERIALS
59
61
1. CARRIAGE OF MATERIALS
1.1 Carriage of materials by mechanical transport including loading, unloading and stacking Code Materials Unit 1 km 2 km 3 km Rate ( 4 km ) 5 km Beyond 5 km upto 10 km per km 9 7.38 9.22 8.02 14.76 7.38 8.02 8.68 19.68 11.81 6.56 Beyond Beyond 10 km 20 km upto 20 per km km per km 10 6.08 7.59 6.60 12.15 6.08 6.60 7.15 16.20 9.72 5.40 11 4.96 6.20 5.39 9.92 4.96 5.39 5.84 13.23 7.94 4.41 12 The rates will be applicable to net quantities after deduction of prescribed percentage for voids mentioned in the specification under subhead "Carriage of Materials". Remarks
2 Lime, moorum, building rubbish Earth Manure or sludge Excavated rock Sand, stone aggregate below 40 mm nominal size Stone aggregate 40 mm nominal size and above Soling stone Bricks Brick Tiles
3 cum cum cum cum cum cum cum 1,000 Nos. 1,000 Nos. tonne
4 66.23 82.78 71.98 132.45 66.23 71.98 77.91 176.60 105.96 58.87
5 75.15 93.94 81.69 150.31 75.15 81.69 88.42 200.41 120.25 66.80
6 83.99 104.98 91.29 167.98 83.99 91.29 98.81 223.97 134.38 74.66
7 92.48 115.60 100.52 184.96 92.48 100.52 108.80 246.62 147.97 82.21
8 100.74 125.92 109.50 201.48 100.74 109.50 118.52 268.64 161.18 89.55
1.1.10 Cement, stone blocks, G.I.. C.I., A.C., & C.C. pipes below 100 mm dia and other heavy materials
62
Code
Materials
Unit 1 km 2 km 3 km
Rate ( 4 km
) 5 km Beyond 5 km upto 10 km per km 9 6.56 8.43 7.38 0.74 8.43 9.84 19.68 32.80 56.23 70.28 98.40 140.57 178.90 196.79 245.99 Beyond Beyond 10 km 20 km upto 20 per km km per km 10 5.40 6.94 6.08 0.61 6.94 8.10 16.20 27.00 46.29 57.86 81.01 115.73 147.29 162.02 202.53 11 4.41 5.67 4.96 0.50 5.67 6.61 13.23 22.05 37.79 47.24 66.14 94.48 120.25 132.27 165.34
Remarks
1 1.1.11 1.1.12 1.1.13 1.1.14 1.1.15 1.1.16 1.1.16.1 1.1.16.2 1.1.16.3 1.1.16.5 1.1.16.6 1.1.16.7 1.1.16.8 1.1.16.9 1.1.16.10 1.1.16.11 1.1.17
2 Steel Timber Tar Bitumen Solvent Steam Coal S.W. pipe 100 mm dia 150 mm dia 200 mm dia 200 mm dia 300 mm dia 350 mm dia 400 mm dia 450 mm dia 500 mm dia 600 mm dia R.C.C. pipe, A.C. pipes, steel cylinder, R.C. pipes, C.I. pipes, C.I. pipes and unreinforces cement pipes
3 tonne cum tonne qtl tonne 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m
4 58.87 75.69 66.23 6.62 75.69 88.30 176.60 294.34 504.58 630.72 883.01 1,261.44 1,605.47 1,766.02 2,207.53
5 66.80 85.89 75.15 7.52 85.89 100.21 200.41 334.02 572.61 715.76 1,002.06 1,431.52 1,821.93 2,004.12 2,505.15
6 74.66 95.99 83.99 8.40 95.99 111.98 223.97 373.28 639.91 799.88 1,119.83 1,599.76 2,036.06 2,239.67 2,799.59
7 82.21 105.69 92.48 9.25 105.69 123.31 246.62 411.03 704.62 880.77 1,233.08 1,761.55 2,241.97 2,466.17 3,082.71
8 89.55 115.13 100.74 10.07 115.13 134.32 268.64 447.73 767.54 959.43 1,343.20 1,918.85 2,442.18 2,686.39 3,357.99
12
63
Code
Materials
Unit 1 km 2 km 3 km
Rate ( 4 km
) 5 km Beyond 5 km upto 10 km per km 9 16.13 21.55 26.88 43.73 62.15 76.81 107.54 146.64 179.23 268.84 403.26 537.69 Beyond Beyond 10 km 20 km upto 20 per km km per km 10 13.28 17.74 22.13 36.00 51.16 63.24 88.54 120.73 147.56 221.34 332.01 442.68 11 10.84 14.48 18.07 29.39 41.77 51.63 72.28 98.57 120.47 180.70 271.05 361.41
Remarks
1 1.1.17.1 1.1.17.2 1.1.17.3 1.1.17.4 1.1.17.5 1.1.17.6 1.1.17.7 1.1.17.8 1.1.17.9 1.1.17.10 1.1.17.11 1.1.17.12
2 100 mm dia 125 mm dia 150 mm dia 200 mm dia 250 mm dia 300 mm dia 350 mm dia 400 mm dia 450 mm & 500 mm dia 600, 700, 750 & 800 mm dia 900 mm dia 1000, 1100 & 1200 mm dia
3 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m
4 144.76 193.36 241.26 392.45 557.69 689.31 965.04 1,315.96 1,608.40 2,412.60 3,618.90 4,825.19
5 164.27 219.43 273.79 445.36 632.88 782.25 1,095.15 1,493.38 1,825.25 2,737.87 4,106.81 5,475.74
6 183.58 245.22 305.97 497.70 707.26 874.19 1,223.86 1,668.90 2,039.77 3,059.66 4,589.49 6,119.32
7 202.15 270.02 336.91 548.04 778.79 962.60 1,347.63 1,837.68 2,246.06 3,369.08 5,053.63 6,738.17
8 220.20 294.13 366.99 596.98 848.33 1,048.55 1,467.97 2,001.78 2,446.62 3,669.94 5,504.90 7,339.87
12
64
2 Lime, moorum, building rubbish Earth Manure or sludge Excavated rock Sand, stone aggregate below 40 mm nominal size Stone aggregate 40 mm nominal size and above Soling stone Bricks
6 The rate is applicable to net quantities after deduction of prescribed percentage for voids mentioned in the specifications under sub-head "Carriage of Materials".
cum cum
1000 Nos.
Brick Tiles, Allahbad 1000 Nos. roofing tiles(flat or round) Steam Coal Stone blocks ,G.I., C.I. pipes below 100 mm dia and other heay material Cement Steel Timber Tar, bitumen etc. S.W. pipe 100 m 100 m 100 m 100 m tonne tonne
6.61 14.20 9.13 8.34 The length of S.W. pipes will be measured exclusive of the internal depth of sockets.
1.2.16.1 100 mm dia 1.2.16.2 150 mm dia 1.2.16.3 200 mm dia 1.2.16.5 250 mm dia
65
Description 2 300 mm dia 350 mm dia 400 mm dia 450 mm dia 500 mm dia 600 mm dia R.C.C. pipes, Steel cylinder, R.C. pipes, C.I. pipes, C.I. pipes and unreinforces cement pipes 100 mm dia 125 mm dia 150 mm dia 200 mm dia 250 mm dia 300 mm dia 350 mm dia 400 mm dia 450 mm & 500 mm dia 600, 700, 750 & 800 mm dia Asbestos cement pipes 50 mm dia 80 mm dia 100 mm dia 150 mm dia
Unit
Rate
1.2.17.1 1.2.17.2 1.2.17.3 1.2.17.4 1.2.17.5 1.2.17.6 1.2.17.7 1.2.17.8 1.2.17.9 1.2.17.10 1.2.18 1.2.18.1 1.2.18.2 1.2.18.3 1.2.18.4
100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m 100 m
153.54 187.87 216.33 324.63 570.58 714.01 1020.80 1187.85 1583.79 1742.17
22.53 27.57 31.74 47.64 83.73 104.77 149.79 174.30 232.40 255.65
The length of the flanged or plain ended concrete R.C.C. pipes, steel cylinders, R.C. pipes and C.I. pipes shall be measured overall. The length of socketed pipes shall be measured exclusive of internal depth of sockets.
The length of asbestos cement pipes shall be measured exclusive of internal depth of sockets.
66
Description Description 2 Loading in or unloading cement from the Railway wagon at siding and carrying the same from or into godowns adjacent to the siding, including stacking the same properly in rows upto any height as per the direction of Engineer-in-charge, sweeping the wagons and screening the swept cement and filling in bags complete. Loading in or unloading from the Railway wagon as per the direction of Engineer-in-charge. Steel
Unit 3 Tonne
Rate 4 42.30
Unit Remarks 5
Rate
1.4
1.4.1
Tonne
61.95
The rates will be applicable in all cases whether materials are unloaded or loaded from Railway siding or directly unloaded on or loaded from transport.
1.4.2
G.I.,C.I.,R.C.C or C.C. pipes upto 500 mm dia. And similar heavy materials. Heavy materials where each piece or bundle, crate or case weighs more than one tonne and R.C.C, C.I. and concrete pipes above 500 mm dia.
Tonne
37.70
1.4.3
Tonne
83.30
No deduction shall be made from carriage rates for such direct unloading or loading.
67
EARTH WORK
69
71
2.0 E A R T H W O R K
Code No. 2.1 Description Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed : 2.1.1 2.2 All kinds of soil 100 sqm 3,786.95 Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : 2.2.1 2.3 All kinds of soil cum 287.40 Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : 2.3.1 2.4 2.5 2.6 All kinds of soil cum cum cum 181.25 2.65 12.10 Deduct for not rolling with power roller of minimum 8 tonnes for banking excavated earth in layers not exceeding 20 cm in depth. Deduct for not watering the excavated earth for banking Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 2.6.1 2.7 All kinds of soil cum 129.35 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. 2.7.1 2.7.2 2.7.3 2.8 Ordinary rock Hard rock (requiring blasting) Hard rock (blasting prohibited) cum cum cum 197.75 347.80 490.10 Unit Rate
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil. cum 130.80 Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift
2.9
72
Code No.
Description upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. 2.9.1 2.9.2 2.9.3 Ordinary rock Hard rock (requiring blasting) Hard rock (blasting prohibited)
Unit
Rate
2.10
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2.10.1 All kinds of soil metre metre metre 101.40 165.60 258.55 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm
2.11
Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). Extra for excavating trenches for pipes, cables, etc, in all kinds of soil for depth exceeding 3 m in depth, but not exceeding 4.5 m. (Rate is over corresponding basic item for depth upto 1.5 metre.) Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : 2.13.1 Ordinary rock : 2.13.1.1 Pipes, cables etc. not exceeding 80 mm dia 2.13.1.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia 2.13.1.3 Pipes, cables exceeding 300 mm dia but not exceeding 600 mm dia 2.13.2 Hard rock (requiring blasting) 2.13.2.1 Pipes, cables etc. not exceeding 80 mm dia 2.13.2.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia 2.13.2.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm dia 2.13.3 Hard rock (blasting prohibited) 2.13.3.1 Pipes, cables etc. not exceeding 80 mm dia 2.13.3.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia 2.13.3.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm dia
metre
135 %
2.12
metre
347%
2.13
73
Description Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 3m in depth but not exceeding 4.5 m. (Rate is over corresponding basic item for depth upto 1.5 metre). Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered). 2.16.1 2.16.2 2.16.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m
Unit
Rate
metre
105%
2.15
metre
262%
2.16
2.17
Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered). 2.17.1 2.17.2 2.17.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m sqm sqm sqm 104.90 114.15 123.85
2.18
Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered) : 2.18.1 2.18.2 2.18.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m sqm sqm sqm 90.25 95.30 100.75
2.19
Extra for planking, strutting and packing materials for cavities (in close timbering) if required to be left permanently in position. (Face area of timber permanently left to be measured). Open timbering in trenches including strutting and shoring complete (measurements to be taken of the face area timbered): 2.20.1 2.20.2 2.20.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m
sqm
1,329.05
2.20
2.21
Open timbering in case of shafts, wells, cesspits, manholes and the like including strutting and shoring complete (Measurements to be taken of the face area timbered): 2.21.1 2.21.2 2.21.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m sqm sqm sqm 44.90 49.20 54.85
2.22
Open timbering over areas including strutting, shoring etc. complete. (Measurements to be taken of the face area timbered): 2.22.1 2.22.2 2.22.3 Depth not exceeding 1.5 m Depth exceeding 1.5 m but not exceeding 3 m Depth exceeding 3 m but not exceeding 4.5 m sqm sqm sqm 30.60 33.65 38.40
74
Description Extra for planking and strutting in open timbering if required to be left permanently in position. (Face area of the timber permanently left to be measured). Extra rates for quantities of works, executed : 2.24.1 2.24.2 In or under water and/or liquid mud, including pumping out water as required In or under foul position, including pumping out water as required
Unit
Rate
sqm
683.85
2.24
20% 25%
Note for item no. 2.24:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level upto the centre of gravity of the quantity executed in difficult conditions. The depth shall be reckoned correct to 0.1 metre. 0.05 metre or more shall be taken as 0.1 metre and less than 0.05 metre ignored. 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. 2.26.1 2.26.2 2.27 2.28 All kinds of soil Ordinary or hard rock cum cum cum 34.60 62.00 749.30
cum
83.80
2.26
Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. 2.28.1 All kinds of soil
100sqm
935.25
2.29
Ploughing the existing ground to a depth of 15 cm to 25 cm and watering the same. 2.29.1 All kinds of soil 100sqm 939.95 Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. 2.30.1 All kinds of soil Ordinary rock 2.30.3 2.30.4 Hard rock (requiring blasting) Hard rock (blasting prohibited) each each each each 41.60 65.95 116.00 149.90
2.30
2.30.2
2.31
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 100sqm Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 100sqm
482.00 247.00
2.32
75
Description Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. 2.33.1 2.33.2 2.33.3 2.33.4 Beyond 30 cm girth upto and including 60 cm girth Beyond 60 cm girth upto and including 120 cm girth Beyond 120 cm girth upto and including 240 cm girth Above 240 cm girth
Unit
Rate
2.34
Supplying chemical emulsion in sealed containers including delivery as specified. 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 185.95 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 2.35.1 Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: 11.80 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: 17.70 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : sqm 88.25 Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : metre 13.30 Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same
2.35
2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration metre 2.35.2
2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration metre 2.35.3
metre cum
127.75 25.35
2.36 2.37
Deduct for disposed soil not levelled and neatly dressed. NEW ITEMS Supply and stacking of Fly ash conforming to IRC- 58 at site, including carriage, loading , unloading & stacking up to any lead (measured stacks will be reduced by 20% for payment). Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.
cum
110.75
2.38
cum
83.80
76
MORTARS
77
79
3.0 MORTAR
Note : These rates are exclusive of water charges, overheads and contractor's profit. Code No. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 Description Cement mortar 1:1 (1 cement : 1 fine sand) Cement mortar 1:2 (1 cement : 2 fine sand). Cement mortar 1:3 (1 cement : 3 fine sand). Cement mortar 1:4 (1 cement : 4 fine sand). Cement mortar 1:5 (1 cement : 5 fine sand). Cement mortar 1:6 (1 cement : 6 fine sand). Cement mortar 1:2 (1 cement : 2 coarse sand). Cement mortar 1:3 (1 cement : 3 coarse sand). Cement mortar 1:4 (1 cement : 4 coarse sand). Cement mortar 1:5 (1 cement : 5 coarse sand). Cement mortar 1:6 (1 cement : 6 coarse sand). Cement mortar 1:2 (1 cement : 2 stone dust). Cement mortar 1:2 (1 cement : 2 marble dust). Cement mortar 1:5 (1 cement : 5 marble dust). White cement mortar 1:2 (1 white cement : 2 marble dust). White cement mortar 1:3 (1 white cement : 3 marble dust). White cement mortar 1:5 (1 white cement : 5 marble dust). Mud mortar Mortar in lime , surkhi ( 50% red and 50% light yellow) and marble dust 1:1.5:0.5 Unit cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum Rate 5,961.50 4,407.85 3,631.95 2,971.80 2,616.35 2,311.70 4,863.85 4,145.55 3,485.40 3,129.95 2,825.30 4,678.60 4,749.85 3,001.55 9,509.85 7,587.15 5,171.55 301.10 2,111.30
80
CONCRETE WORK
81
83
Code No. 2260 2261 2262 7319 7326 7327 7328 7329 7330 7331 7332 7333 7334 8732 9999
Description Carriage of Brick aggregate Carriage of Fine sand (1 part badarpur sand : 2 parts jamuna sand) Carriage of Fly ash Wall form panel 1250x500 mm Corner angle 45x45x5 mm 1.50 m long 100 mm channel shoulder 2.5 m long Double clip ( bridge clip) Single clip M.S. tube 40 mm dia Wall form panel 1250x450 mm Corner angle 45x45x5 mm 2.50 m long Column clamp 450x1070 mm Prop 2 m ( 2-3.5 m) Synthetic ployster triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1:34 to 1:40 Sundries
Unit cum cum cum each each each each each metre each each each each kg L.S.
Rate 95.22 87.60 87.60 1,050.00 300.00 1,160.00 97.00 77.00 280.00 1,040.00 340.00 1,220.00 830.00 365.00 1.49
84
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 4.2.1 4.2.2 4.2.3 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1:3 (1 cement:1 coarse sand:3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum cum cum 6,901.90 5,663.30 5,272.40
85
Code No.
Description 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 1:3:6 (1 cement : 3 fine sand : 6 graded stone aggregate 40 mm nominal size) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
Unit
Rate
4.3
Centering and shuttering including strutting, propping etc. and removal of form work for : 4.3.1 4.3.2 Foundations, footings, bases for columns Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. Columns, piers, abutments, pillars, posts and struts sqm 166.90
sqm sqm
285.15 365.60
4.3.3 4.4
Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 4.4.1 4.4.2 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum 4,514.05 4,024.00
CEMENT CONCRETE (PRE-CAST) 4.5 Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering complete. 4.5.1 4.5.2 4.5.3 4.6 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum cum 5,528.25 5,137.35 4,736.60
Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 4.6.1 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cum 4,712.80
4.7
Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3
86
Code No.
Description (1 cement : 3 coarse sand), cost of required centering, shuttering complete : 4.7.1 4.7.2 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
Unit
Rate
cum cum
7,758.85 7,268.80
4.8
Providing and fixing up to floor five level precast cement concrete hollow block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 4.8.1 4.8.2 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum 5,939.00 5,713.60
4.9
Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape, including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes 40 mm dia and 450 mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150 mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), including necessary excavation of size 250x250x450 mm deep for the same in bitumen/concrete pavement at specified spacing. DAMP- PROOF COURSE Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
each
465.80
4.10
sqm
207.55
4.11
sqm
254.70 35.35
4.12 4.13
Extra for providing and mixing water proofing material in cement concrete per 50 kg work in doses by weight of cement as per manufacturer's specification. cement Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. MISCELLANEOUS Extra for concrete work in superstructure above floor V level for each four floors or part thereof.
sqm
96.65
4.14 4.15
cum
539.35 325.10
Extra for laying concrete in or under water and/or liquid mud including cum per cost of pumping or bailing out water and removing slush etc. complete. meter depth Note for item No. 4.15 :- The quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.
87
Description Extra for laying concrete in or under foul positions. Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
Unit cum
Rate 128.10
sqm
338.75
4.18
Extra for addition of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete/RCC/Flooring/water retaining structures by using Per Bag of 125gms of synthetic Polyester triangular fibre for 50 Kg cement used 50 Kg of as per directions of Engineer-in-Charge. cement NEW ITEMS Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : (1) Excess/less cement used than specified in this item is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC. 4.19.1 All works upto plinth level : cum cum 4.19.1.1 M-15 grade plain cement concrete (cement content considered @ 240 kg/cum) 4.19.1.2 M-10 grade plain cement concrete (cement content considered @ 220 kg/cum) 4.19.2 All works above plinth and upto floor V level : cum cum 4.19.2.1 M-15 grade plain cement concrete (cement content considered @ 240 kg. /cum) 4.19.2.2 M-10 grade plain cement concrete (cement content considered @ 220 kg/cum) Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases.
53.00
4.19
4,969.95 4,847.75
5,358.30 5,236.10
4.20
Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit
88
Code No.
Description mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in charge. Note : 1) Excess/less cement used than specified in this item is payable/ recoverable separately. 4.20.1 All works upto plinth level : 4.20.1.1 M-15 grade plain cement concrete (cement content considered @ 240 kg/cum) 4.20.1.2 M-10 grade plain cement concrete (cement content considered @ 220 kg/cum) 4.20.2 All works above plinth and upto floor V level : 4.20.2.1 M-15 grade plain cement concrete. (cement content considered @ 240 kg. /cum) 4.20.2.2 M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)
Unit
Rate
cum cum
5,086.95 4,964.75
cum cum
5,475.30 5,353.10
89
91
93
Code No. 0370 0639 0768 0769 0770 0982 0983 0992 1004 1005 1015 1021 1034 1197 1198 1224 1225 2200 2202 2203 2204 2205 2209 2211 2261 2273 2302 2391 2392 2447 7318 7319 7320 7321
Description Coal (steam) Bright finished or black enameled mild steel screws 25 mm Cement Concrete Jali 50 mm thick Cement Concrete Jali 40 mm thick Cement Concrete Jali 25 mm thick Coarse sand (zone III) Fine sand (zone IV) Galvanised steel plain sheets Average rate of Mild steel round bars for reinforcements Twisted steel / deformed bars Mild steel expanded metal 20x60 mm strands Hard drawn steel wire fabric Bolts and nuts up to 300 mm in length Second class kail wood in scantling Second class kail wood in planks Hard drawn steel wire Mild steel flat strap fitting Carriage of Steam coal Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Timber Carriage of Steel Carriage of Cement Carriage of Tar bitumen Carriage of Fine sand (1 part badarpur sand : 2 parts jamuna sand) Carriage of A.C.sheet and accessories Carriage of G.I.sheet and accessories Strips-Aluminium fluted 3.15 mm thick and 150 mm wide Strips Aluminium fluted 3.15 mm thick and 200 mm wide Hollock ballies 125 mm diameter Plasticizer / super plasticizer Wall form panel 1250x500 mm Tie bolt 12 mm dia 100 mm length Tie bolt 12 mm dia 150 mm length
Unit quintal 100 nos sqm sqm sqm cum cum quintal quintal quintal sqm sqm quintal 10 cudm 10 cudm quintal quintal tonne cum cum cum tonne tonne tonne cum tonne tonne metre metre metre kilogram each each each
Rate 400.00 30.00 210.00 180.00 145.00 1,120.00 640.00 4,750.00 4,050.00 4,500.00 270.00 430.00 5,400.00 250.00 250.00 4,200.00 3,950.00 100.11 87.60 87.60 100.11 77.87 77.87 87.60 87.60 77.87 77.87 228.00 323.00 35.00 36.50 1,050.00 38.00 50.00
94
Code No. 7322 7323 7324 7325 7326 7327 7328 7329 7330 7331 7332 7333 7334 7342 7343 7344 7345 7346 8659 9999
Description Tie bolt 20 mm dia 150 mm length Tie bolt 20 mm dia 225 mm length Spring coil 12 mm Plastic cone 12 mm dia Corner angle 45x45x5 mm 1.50 m long 100 mm channel shoulder 2.5 m long Double clip ( bridge clip) Single clip M.S. tube 40 mm dia Wall form panel 1250x450 mm Corner angle 45x45x5 mm 2.50 m long Column clamp 450x1070 mm Prop 2 m ( 2-3.5m) Adjustable span ESO+SI (2.35-3.40) Adjustable telescopic prop 3 m (2.02-3.75 m) Beam clamp 300-380 mm (450-1070 mm) Prop 4 m Double coupler Water proof ply 12mm thick Sundries NEW CODES
Unit each each each each each each each each metre each each each each each each each set each each sqm L.S.
Rate 62.00 80.00 16.00 18.00 300.00 1,160.00 97.00 77.00 280.00 1,040.00 340.00 1,220.00 830.00 1,825.00 1,150.00 422.00 1,170.00 55.00 645.00 1.49
1 mm thick Stainless Steel Cover plate grade 304 Coupler 16 mm dia Coupler 20 mm dia Coupler 25 mm dia Coupler 28 mm dia Coupler 32 mm dia Chemical ASTMC-type I Chemical ASTMC-type II
95
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 5.2.1 5.2.2 5.2.3 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum cum cum 6,974.30 5,735.75 5,344.80
5.3
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15 up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Reinforced cement concrete work in chimneys, shafts, up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Reinforced cement concrete work in well-steining, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
cum
5,494.55
5.4
cum
5,181.25
5.5
cum
5,684.55
5.6
cum
5,419.40
5.7
cum
4,537.00
96
Description Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1:3 (1 cement : 1 coarse sand : 3 graded stone aggregate 20 mm nominal size). FORM WORK
Unit
Rate
cum
5,442.00
5.9
Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.1 5.9.2 5.9.3 5.9.4 5.9.5 5.9.6 5.9.7 5.9.8 5.9.9 5.9.10 5.9.11 5.9.12 5.9.13 5.9.14 5.9.15 Foundations, footings, bases of columns, etc. for mass concrete Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Suspended floors, roofs, landings, balconies and access platform Shelves (Cast in situ) Lintels, beams, plinth beams, girders, bressumers and cantilevers Columns, Pillars, Piers, Abutments, Posts and Struts Stairs, (excluding landings) except spiral-staircases Spiral staircases (including landing) Arches, domes, vaults up to 6 m span Extra for arches, domes, vaults exceeding 6 m span Chimneys and shafts Well steining Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards Extra for shuttering in circular work (20% of respective centering and shuttering items) Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like Edges of slabs and breaks in floors and walls metre sqm sqm sqm sqm sqm 99.45 441.10 495.50 398.35 411.10 488.05 sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm 166.90 285.15 311.20 311.20 262.25 365.60 326.30 290.90 866.70 417.85 285.15 205.15 470.10 20.00%
sqm
166.90
5.9.16
5.9.16.1 Under 20 cm wide 5.9.16.2 Above 20 cm wide 5.9.17 5.9.18 5.9.19 5.9.20 Cornices and mouldings Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like Weather shade, Chajjas, corbels etc., including edges Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick
97
Code No.
Description 5.9.21 Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick
Unit
Rate
sqm
459.00
5.10
Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering complete as per the direction of Engineer-in-charge. 5.10.1 5.10.2 5.10.3 5.10.4 12 mm dia. & 100 mm length 12 mm dia. & 150 mm length 20 mm dia. & 150 mm length 20 mm dia.& 225 mm length each set each set each set each set 125.95 139.85 153.80 174.70
5.11
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 121.65
PRE - CAST R.C.C. 5.12 Providing, hoisting and fixing up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size). Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in small lintels not exceeding 1.5 m clear span up to floor five level, including the cost of required centering, shuttering but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc., including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in lintels, beams and bressumers, including setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering and shuttering but excluding the cost of reinforcement, with 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in vertical & horizontal fins, individually or forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse sand), including the cost of required centering, shuttering but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
cum
5,265.20
5.13
cum
8,720.30
5.14
cum
8,089.00
5.15
cum
6,754.00
5.16
cum
9,872.85
5.17
cum
5,897.50
98
Description Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 5.18.1 5.18.2 5.18.3 50 mm thick 40 mm thick 25 mm thick
Unit
Rate
ENCASING ROLLED STEEL SECTION 5.19 Encasing rolled steel sections, in beams and columns, with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size), including centering and shuttering complete but excluding cost of reinforcement. Encasing rolled steel section in grillages with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size), including centering and shuttering but excluding cost of expanded metal and hangers. Extra for providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for encasing of rolled steel sections in beams, columns and grillages, excluding cost of hangers. STEEL REINFORCEMENT 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.1 5.22.2 5.22.3 5.22.4 5.22.5 5.22.6 5.22A Mild steel and Medium Tensile steel bars Hard drawn steel wire Cold twisted bars Hot rolled deformed bars Hard drawn steel wire fabric Thermo-Mechanically Treated bars kilogram kilogram kilogram kilogram kilogram kilogram 56.75 58.15 62.25 62.25 73.40 62.25
cum
7,259.65
5.20
cum
4,941.60
5.21
sqm
349.90
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22.1 5.22.2 5.22.3 5.22.4 5.22.5 5.22.6 Mild steel and Medium Tensile steel bars Hard drawn steel wire Cold twisted bars Hot rolled deformed bars Hard drawn steel wire fabric Thermo-Mechanically Treated bars kilogram kilogram kilogram kilogram kilogram kilogram 56.75 58.15 62.25 62.25 73.40 62.25
99
Code No.
Description MISCELLANEOUS
Unit
Rate
5.23 5.24
Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). Extra for rendering smooth the top of suspended floors, landings and staircases (treads and risers) with cement mortar 1:2 (1 cement : 2 coarse sand), including a floating coat of neat cement and protecting the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand in case of suspended floor and bricks laid in mud mortar in case of landings and steps, including subsequent removal and cleaning of the same. Providing and fixing in position copper plate as per design for expansion joints. Providing and filling in position, blown bitumen in expansion joints.
sqm
101.00
sqm kg per cm depth per cm width per 100 m per cm depth per cm width per 100 m per cm depth per 100 m
5.25 5.26
5.27
Providing and filling in position bitumen mix filler of Proportion 80 kg of hot bitumen, 1 kg. of cement and 0.25 cubicmetre of coarse sand for expansion joints. Providing and fixing in position 12 mm thick bitumen impregnated fibre board conforming to IS: 1838, including cost of primer, sealing compound in expansion joints. Providing and fixing sheet covering over expansion joints with iron screws as per design. 5.29.1 Non-asbestos fibre cement board 6 mm thick as per IS: 14862. 5.29.1.1 150mm wide 5.29.1.2 200mm wide 5.29.2 Aluminium fluted strips 3.15 mm thick. 5.29.2.1 150 mm wide 5.29.2.2 200 mm wide
167.35
5.28
430.30
5.29
5.30 5.31
Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. Extra for laying reinforced cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete. Note For Item No. 5.31:- The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.
cum
325.10
5.32
cum
128.10
100
Code No.
Unit
Rate
5.33
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). 5.33.1 5.33.2 All works upto plinth level All works above plinth level upto floor V level cum cum 5,242.15 5,781.50
5.34
Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. 5.34.1 Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum) Providing M-35 grade concrete instead of M-25 grade BMC/ RMC. (Note : Cement content considered in M-35 is @ 350 kg/ cum) Providing M-40 grade concrete instead of M-25 grade BMC/ RMC.(Note : Cement content considered in M-40 is @ 360 kg/ cum)
cum
63.20
5.34.2
cum
126.45
5.34.3
cum quintal
186.90 589.80
5.35 5.36
Add for using extra cement in the items of design mix over and above the specified cement content therein. Providing and placing in position precast reinforced cement concrete waffle units, square or rectangular, as per design and shape for floors and roofs in 1:1:3 (1 Cement : 1 coarse sand : 3 graded stone aggregate 10 mm nominal size), including flush or deep ruled pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), making necessary holes of required sizes for carrying through service lines etc., providing steel hooks for lifting etc, form work in precasting, handling, hoisting, centering and erection complete for all floor levels but excluding the cost of reinforcement. Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge.
cum
14,097.20
5.37
101
Code No.
Description (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). 5.37.1 5.37.2 All works upto plinth level All works above plinth level upto floor V level
Unit
Rate
5.38
Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.
NEW ITEMS 5.40 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC. 5.40.1 5.40.2 All works up to Plinth level. All works above plinth & up to floor V level. cum cum 5,519.40 6,059.20
Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases. 5.41 Supplying and applying pre tested and approved water based concrete curing compound to concrete/ masonry surface, all as per manufacturers specification and direction of Engineer-in-charge. 5.41.1 5.41.2 5.42 Non pigmented wet curing compound Pigmented wet curing compound kg kg 83.05 97.00
Providing and fixing tapered / parallel threaded couplers conforming to IS code on Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification, to reinforcement bars including threading, enlargement at connection by forging, protecting the prepared reinforcement bars and related operations as required to complete the works per direction of Engineer-in-Charge. (The length of the bars in
102
Code No.
Description which coupler is to be provided should not be less than 4 metre, no deduction for labour and binding wire saved for not providing lap length shall be made). 5.42.1 5.42.2 5.42.3 5.42.4 5.42.5 Coupler for 16 mm diameter reinforcement bar Coupler for 20 mm diameter reinforcement bar Coupler for 25 mm diameter reinforcement bar Coupler for 28 mm diameter reinforcement bar Coupler for 32 mm diameter reinforcement bar
Unit
Rate
5.43
Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. 5.43.1 5.43.2 200 mm wide. 300 mm wide. kg kg 559.85 815.40
103
BRICK WORK
105
1,000 nos 1,000 nos 1,000 nos cum tonne 1,000 nos cum tonne 1,000 nos 1,000 nos 1,000 nos, 1,000 nos,
3,100.00 3,600.00 233.60 100.11 77.87 140.16 87.60 77.87 2,900.00 3,000.00 3,900.00 3,300.00
1986 2201 2204 2205 2207 2208 2302 2602 7008 7736 7737
107
Code No. 7738 7900 7901 7902 7903 7904 8655 8656 8657 8658 9999
Description Calcium Silicate Bricks machine moulded conforming to I.S. 4139 - 1989 Modular common burnt clay bricks of class designation 7.5 Machine moulded perforated common burnt clay FPS (non modular) bricks of class designation 12.5 Machine moulded common burnt clay modular perforated bricks of class designation 12.5 Machine moulded common burnt clay FPS (non modular) bricks of class designation 12.5 Machine moulded common burnt clay tile bricks of class designation 12.5 Autoclaved aerated cement (AAC) blocks Gypsum panel 666 X 500 X 100 mm size Bonding plaster for Gypsum panel Mechanised Autoclaved fly ash sand lime non modular bricks Sundries
Unit
Rate
1,000 nos 1,000 nos 1,000 nos 1,000 nos 1,000 nos 1,000 nos cum sqm kg 1,000 nos L.S.
3,600.00 3,150.00 4,150.00 3,800.00 3,550.00 3,700.00 2,025.00 455.00 53.00 4,300.00 1.49
108
Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: 6.2.1 6.2.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement Mortar 1:6 (1 cement : 6 coarse sand). cum cum 3,370.55 3,201.90
6.3
Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : 6.3.1 6.3.2 With F.P.S.(non modular) bricks With Modular bricks cum cum 4,593.40 4,118.80
6.4
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 6.4.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) cum cum 4,067.85 3,876.15
6.5
Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means. Extra for forming cavity 5 cm to 7.5 cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. ties 300 mm long of 25x3 mm section at not less than 3 ties per sqm as per approved design. Providing half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in cement mortar 1:3 (1 Cement : 3 coarse sand) in superstructure for closing cavity 5 to 7.5 cm wide in cavity wall complete with 10 cm / 11.4 cm wide bitumen felt type 3 grade 1. Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. Brick work in plain arches in superstructure above plinth level and upto floor five level including centering and shuttering complete for span up to 6 metres with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand). Brick work in gauged arches in superstructure above plinth level and upto floor five level in cement mortar 1:3 (1 cement : 3 coarse sand) including centering and shuttering complete, for span up to 6 meters with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
cum
250.45
6.6
sqm
80.60
6.7
metre
135.05
6.8
sqm
372.00
6.9
cum
6,384.10
6.10
cum
7,555.35
109
Description Extra for additional cost of centering for arches exceeding 6m span including all shuttering, bolting, wedging and removal (Area of the soffit to be measured). HALF BRICK MASONRY
Unit
Rate
sqm
417.85
6.12
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : 6.12.1 6.12.2 Cement mortar 1:3 (1 cement : 3 coarse sand) cement mortar 1:4 (1 cement : 4 coarse sand) sqm sqm 438.40 416.95
6.13
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.1 6.13.2 Cement mortar 1:3 (1 cement :3 coarse sand) Cement mortar 1:4 (1 cement :4 coarse sand) sqm sqm sqm sqm 498.35 476.85 22.20 63.30
6.14 6.15
Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. BRICK TILE WORK
6.16
Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in foundation and plinth in: 6.16.1 6.16.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) cum cum 5,520.30 5,213.60
6.17
Tile brick masonry with common burnt clay machine moulded tile bricks of class designation 12.5 conforming to IS : 2690 (Part I) in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in superstructure above plinth level up to floor V level in cement mortar 1:6 (1 cement : 6 coarse sand). Deleted. Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in plain arch work in superstructure above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4 coarse sand) including centering and shuttering complete. Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in gauged arch work in superstructure above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4 coarse sand) including centering and shuttering complete. Tile brick masonry work 5 cm thick with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth and upto floor five level.
cum
5,755.10
6.18
cum
5,804.20
6.19 6.20
cum
8,165.45
6.21
cum
9,299.70
6.22
sqm
379.10
110
Code No.
Unit
Rate
6.23
Honey-comb brick work 10 / 11.4 cm thick with common burnt clay bricks of class designation 7.5 in super structure above plinth level upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand).
sqm
316.45 325.10
6.24
Extra for laying brick work in or under water and/or liquid mud including cum/mtr cost of pumping or bailing out water and removing slush etc. complete. depth NOTE :- The quantity will be calculated by multiplying the depth measured from sub - soil water level up to the centre of gravity of brick work under sub - water with the quantity of brick work in cum executed under the sub - soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored.
6.25 6.26
Extra for laying brick work in or under foul position. EXPOSED BRICK WORK Brick work with common burnt clay selected F.P.S. (non modular) bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand) 6.26.1 6.26.2 From ground level upto plinth level Above plinth level upto floor V level
cum
128.10
cum cum
3,390.90 3,979.20
6.27
Brick work with common burnt clay modular bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). 6.27.1 6.27.2 From ground level upto plinth level Above plinth level upto floor V level cum cum 3,225.50 3,785.10
6.28
Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). 6.28.1 6.28.2 From ground level upto plinth level Above plinth level upto floor V level cum cum 3,480.05 4,039.60
6.29
Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). 6.29.1 6.29.2 From ground level upto plinth level Above plinth level upto floor V level cum cum 3,713.15 4,252.75
6.30
Brick work with common burnt clay machine moulded perforated F.P.S. (non modular) bricks of class designation 12.5 conforming IS : 2222 in exposed brick work including making horizontal and vertical grooves 10mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). 6.30.1 6.30.2 From ground level upto plinth level Above plinth level upto floor V level cum cum 4,057.40 4,617.00
111
Description Brick work with common burnt clay machine moulded perforated modular bricks of class designation 12.5 conforming to IS : 2222 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). 6.31.1 6.31.2 From ground level upto plinth level Above plinth level upto floor V level
Unit
Rate
cum cum
3,593.15 4,152.75
6.32
Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : 6.32.1 6.32.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) cum cum 4,102.05 3,910.35
6.33 6.34
Deleted. Brick work with non modular fly ash lime bricks (FALG Bricks) conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : 6.34.1 6.34.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 Coarse sand) cum cum 4,147.20 3,978.50
6.35
Brick work with modular calcium silicate bricks machine moulded conforming to IS:4139, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : 6.35.1 6.35.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 Coarse sand) cum cum 4,316.85 4,148.20
6.36
Brick work with modular extruded brunt fly ash clay sewer bricks (Conforming to IS: 4885 ) in foundation and plinth : 6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) cum 3,794.80
6.37
Brick work with modular extruded brunt fly ash clay sewer bricks (conforming to IS : 4885) in arches in foundation and plinth in cement mortar 1:3 ( 1 cement : 3 fine sand). Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. Deleted. Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturers specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2 Extra for Gypsum panel Partitions in superstructure above floor V level for every four floors or part thereof.
cum
6,221.65
6.38
cum
4,508.30
6.39 6.40
sqm sqm
730.90 49.65
6.41
112
Description Brick work with mechanized autoclaved flyash sand lime non modular bricks conforming to IS: 12894 of class designation 10 in superstructure above plinth level up to floor V level in. 6.42.1 6.42.2 Cement mortar 1:4 (1 cement :4 coarse sand) Cement mortar 1:6 (1 cement :6 coarse sand)
Unit
Rate
cum cum
4,871.10 4,679.45
6.43 6.44
Deleted. Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
metre
26.05
NEW ITEMS 6.45 Half brick masonry with non modular fly ash lime Gypsum bricks (FALG bricks) of class designation 10, conforming to IS : 12894, in super structure above plinth and upto floor V level. 6.45.1 6.45.2 6.46 Cement mortar 1 : 3 (1 cement : 3 coarse sand) Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm sqm 524.60 503.10
Half brick masonry with non modular mechanised auto claved fly ash sand lime bricks of class designation 10, conforming to IS : 12894, in super structure above plinth and upt floor V level. 6.46.1 6.46.2 Cement mortar 1 : 3 (1 cement : 3 coarse sand) Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm sqm 590.20 568.75
113
STONE WORK
115
117
Description Second class kail wood in scantling Welding by electric plant Mild steel flat strap fitting Cutting marble or sand stone slab up to 50 mm thick by mechanical device Carriage of Timber Carriage of Soling stone & masonry stone Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of G.I.sheet and accessories 8 mm thick granite stone tiles (mirror polished of all shades) Mild steel tubes hot finished welded type Stainless steel cramp 8 mm thick (mirror polished tiles machine cut edge) Raj Nagar white Red sand stone gang saw cut 30 mm thick White sand stone gang saw cut 30 mm thick Stainless steel cramps(weight 260 grams) with nuts, bolts and washer for dry stone cladding Sundries
metre cum cum tonne tonne sqm kilogram kilogram sqm sqm sqm
8.00 100.11 103.06 77.87 77.87 675.00 48.00 320.00 480.00 400.00 435.00
2204 2215 2216 2302 2750 4009 7339 7439 8683 8684 8698
each L.S.
84.00 1.49
9999
118
Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 3,615.35
7.3 7.4
Deleted Extra for random rubble masonry with hard stone in : 7.4.1 7.4.2 Square or rectangular pillars Circular pillars cum cum cum 261.35 812.75 328.05
7.5
Extra for random rubble masonry with hard stone curved on plan for a mean radius not exceeding 6 m. COURSED RUBBLE MASONRY
7.6
Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : 7.6.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 3,468.80
7.7
Coursed rubble masonry (second sort) with hard stone in foundation & plinth with : 7.7.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 3,255.25
7.8
Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level. 7.8.1 7.8.2 Masonry work (first sort) , in cement mortar 1:6 (1 cement : 6 coarse sand) Masonry work (second sort) , in cement mortar 1:6 (1 cement: 6 coarse sand) cum cum 4,017.70 3,804.10
7.9 7.10
Deleted. Extra for coursed rubble masonry with hard stone (first or second sort) in : 7.10.1 7.10.2 Square or rectangular pillars Circular pillars cum cum cum 289.90 919.15 356.10
7.11
Extra for coursed rubble masonry with hard stone (first or second sort) curved on plan for a mean radius not exceeding 6 m. ASHLAR MASONRY
7.12
Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement
119
Code No.
Description mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.12.1 One face dressed 7.12.1.1 Red sand stone 7.12.1.2 White sand stone 7.12.2 Both face dressed 7.12.2.1 Red sand stone 7.12.2.2 White sand stone
Unit
Rate
7.13
Stone work plain ashlar in arches in super structure upto floor V level in cement mortar 1:3 (1 cement : 3 coarse sand) including centring, shuttering and pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. 7.13.1 One face dressed cum cum cum cum 26,021.00 26,795.00 32,244.00 33,017.00 7.13.1.1 Red sand stone 7.13.1.2 White sand stone 7.13.2 Both face dressed 7.13.2.1 Red sand stone 7.13.2.2 White sand stone
7.14
Stone work plain ashlar in domes , in super structure upto floor V level in cement mortar 1:3 (1 cement : 3 coarse sand) including centring, shuttering and pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. 7.14.1 One face dressed cum cum cum cum 38,362.00 39,136.00 53,528.00 54,302.00 7.14.1.1 Red sand stone 7.14.1.2 White sand stone 7.14.2 Both face dressed 7.14.2.1 Red sand stone 7.14.2.2 White sand stone
7.15
Stone work ashlar punched (ordinary) in superstructure upto floor five level in cement mortar 1:6 (1 white cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. 7.15.1 One face dressed cum cum cum cum cum 21,366.00 22,141.00 26,668.00 27,442.00 574.00 7.15.1.1 Red sand stone 7.15.1.2 White sand stone 7.15.2 Both faced punched 7.15.2.1 Red sand stone 7.15.2.2 White sand stone
7.16
Extra for stone work, random rubble / coursed rubble masonry / ashlar masonry above floor V level for every four floors or part thereof.
120
Description Extra for plain ashlar or ashlar punched in : 7.17.1 Square or rectangular pillars
Unit
Rate
cum cum
1,552.00 1,080.00
Extra for stone work; plain ashlar or ashlar punched curved on plan with a mean radius not exceeding 6 m. Extra for additional cost of centering for arches exceeding 6m span including all strutting, bolting, wedging etc. and removal (area of soffit to be measured). SUNK, MOULDED, CARVED ASHLAR MASONRY Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.20.1 7.20.2 Red sand stone White sand stone
sqm
417.85
7.20
cum cum
30,116.00 30,891.00
7.21
Extra for stone work ashlar sunk or moulded or sunk and moulded or carved in : 7.21.1 7.21.2 Triangular or Square or rectangular pillars Circular or polygonal pillars cum cum per metre per cm girth 2,024.00 5,736.00 16.60
7.22
Extra for stone work ashlar sunk or moulded in cornices. MISCELLANEOUS STONE WORK
7.23
Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 7.23.1 Red sand stone - exposed face fine dressed with rough backing. sqm sqm sqm sqm sqm 2,015.55 1,919.85 1,824.35 1,728.45 1,632.70 7.23.1.1 70 mm thick 7.23.1.2 60 mm thick 7.23.1.3 50 mm thick 7.23.1.4 40 mm thick 7.23.1.5 30 mm thick 7.23.2 Red sand stone - Exposed face machine cut and table rubbed with rough backing. sqm sqm sqm sqm sqm 2,618.85 2,523.15 2,427.65 2,331.75 2,236.00
7.23.2.1 70 mm thick 7.23.2.2 60 mm thick 7.23.2.3 50 mm thick 7.23.2.4 40 mm thick 7.23.2.5 30 mm thick
121
Code No.
Description 7.23.3 White sand stone - exposed face fine dressed with rough backing .
Unit
Rate
7.23.3.1 70 mm thick 7.23.3.2 60 mm thick 7.23.3.3 50 mm thick 7.23.3.4 40 mm thick 7.23.3.5 30 mm thick 7.23.4 White sand stone - Exposed face machine cut and table rubbed with rough backing.
7.23.4.1 70 mm thick 7.23.4.2 60 mm thick 7.23.4.3 50 mm thick 7.23.4.4 40 mm thick 7.23.4.5 30 mm thick 7.24 7.25 Extra for stone work (veneer work) curved on plan with a mean radius not exceeding 6 m. Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. Providing and fixing stone dowels 10x5x2.50 cm cut to double wedge shape as per design in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. Providing and fixing sloping chajja of stone 40 mm thick and upto 80 cm wide beyond the wall as measured along the slope in cement mortar 1:4 (1 cement : 4 coarse sand) with 12 mm diameter anchoring steel bar, 45 cm long, fixed in each stone and supported on and including with bricks cove in cement mortar 1:4 (1 cement : 4 coarse sand), including pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.28.1 Red sand stone : 7.28.1.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 7.28.2 White sand stone : 7.28.2.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 7.29 Providing and fixing horizontal chajja of stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand), including
kg
524.10
7.26
each
30.60
7.27
each
27.40
7.28
sqm
1,011.55
sqm
1,035.50
122
Code No.
Description pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.29.1 7.29.2 Red sand stone White sand stone
Unit
Rate
sqm sqm
619.70 640.60
7.30
30 mm red sand stone sun-shade (chisel-dressed) supported on red sand stone brackets, fixed in walls with cement mortar 1:4 (1 cement : 4 coarse sand), including finishing complete. Providing and fixing red sand stone brackets 55x22.5x45 cm sunk and moulded including providing and fixing with 4 Nos gun metal cramp 25x6 mm 30 cm long and dowel bars 7.5 cm long 6 mm dia as per design. Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. 7.32.1 7.32.2 Red sand stone White sand stone
sqm
652.65
7.31
each
2,218.65
7.32
cum cum
29,914.00 30,690.00
7.33
Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. 7.33.1 7.33.2 Red sand stone White sand stone sqm sqm 6,798.15 6,817.30 325.10
7.34
Extra for laying stone work in or under water and/or liquid mud including cum/ mtr cost of pumping or bailing out water and removing slush etc. complete. depth NOTE :- The quantity will be calculated by multiplying the depth measured from sub - soil water level up to the centre of gravity of stone work under sub - water with the quantity of stone work in cum executed under the sub - soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored.
7.35 7.36
Extra for laying stone work in or under foul position. Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge. Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete.
cum
128.10
sqm
1,192.45
7.37
123
Code No.
Description (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately). 7.37.1 Kota stone slabs exposed face dressed and rubbed. 7.37.1.1 25 mm thick
Unit
Rate
sqm
1,177.50
7.38
Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 7.38.1 8mm thick (mirror polished and machine cut edge) sqm sqm sqm 1,466.35 1,234.20 65.85 7.38.1.1 Granite stone of any colour and shade 7.38.1.2 Raj Nagar plain white marble/ Udaipur green marble/ Zebra black marble
7.39
Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of. STONE WORK IN DRY CLADDING Providing and fixing dry cladding upto 10 metre heights with 30 mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). 7.40.1 7.40.2 Red sand stone White sand stone
7.40
sqm sqm
1,989.40 2,048.35
7.41
Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid). Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.
kg
119.00
7.42
each
171.20
124
125
127
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 8.2.1 8.2.1.1 8.2.1.2 8.2.2 8.2.2.1 8.2.2.2 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm Area of slab over 0.50 sqm Granite of any colour and shade Area of slab upto 0.50 sqm Area of slab over 0.50 sqm sqm sqm 3,041.15 3,083.40 sqm sqm 1,894.75 1,980.80
8.3
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.1 8.3.2 Marble work Granite work metre metre 105.70 178.75
8.4
Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.
metre
185.80
8.5
each sqm
281.10 163.10
8.6
128
Description Providing and fixing cramps of required size & shape in RCC/ CC / Brick masonry backing with cement mortar 1:2 ( 1 cement :2 coarse sand), including drilling necessary hole in stones and embedding the cramp in the hole (fastener to be paid separately). 8.7.1 8.7.2 Gunmetal cramps Stainless steel cramps
Unit
Rate
kg kg
492.70 524.10
8.8
Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. 8.8.1 8.8.1.1 8.8.1.2 8.8.1.3 Wedge expansion type Fastener with threaded dia 6 mm Fastener with threaded dia 10 mm Fastener with threaded dia 12 mm each each each 22.05 24.70 38.95
8.9
Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8.9.1 8.9.1.1 8.9.1.2 8mm thick Raj nagar plain white marble/ Udaipur green marble/ Zebra black marble Granite of any colour and shade sqm sqm 1,207.90 1,606.70
8.10
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. 8.10.1 8.10.2 White Agaria Marble Stone Granite Stone of approved shade sqm sqm 2,670.75 2,942.05
129
131
133
Code No. 0400 0401 0402 0403 0408 0409 0410 0411 0412 0413 0414 0423 0424 0425 0426 0431 0432 0433 0438 0447 0449 0450 0451 0452 0453 0555 0556 0557 0558
Description
Unit
Rate
Brass tower bolt (barrel type ) 250 x 10 mm Brass tower bolt (barrel type ) 200x 10 mm Brass tower bolt (barrel type) 150 x 10 mm Brass tower bolt (barrel type) 100 x 10 mm Brass handles 125mm with plate 175x32 mm Brass handles 100 mm with plate 150x32 mm Brass handles 75mm with plate 125x32mm Brass door latch 300x16x5mm (0.380 kg) Brass door latch 250x16x5mm (0.350 kg) Brass mortice latch and lock 100 x 65 mm with 6 levers and a pair of brass lever handles Brass mortice latch 100x65 mm with a pair of brass lever handles Brass casement window fastener Brass casement stays (straight peg type ) 300 mm weighing not less than 0.33 kg Brass casement stays (straight peg type ) 250 mm weighing not less than 0.28 kg Brass casement stays (straight peg type ) 200 mm weighing not less than 0.24 kg Brass hasps and staples (safety type) 150 mm Brass hasps and staples (safety type) 115 mm Brass hasps and staples (safety type) 90 mm Brass Night latch Brass cupboard knob or wardrobe knob 50 mm Brass screws 50 mm Brass screws 40 mm Brass screws 30 mm Brass screws 25 mm Brass screws 20 mm Chromium plated Brass handles 125 mm with plate 175 x32 mm Chromium plated Brass handles 100 mm with plate 150 x 32 mm Chromium plated Brass handles 75 mm with plate 125x32 mm Chromium plated Brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever handles
each each each each each each each each each each each each each each each 10 nos 10 nos 10 nos each each 100 nos 100 nos 100 nos 100 nos 100 nos each each each each
225.00 175.00 140.00 90.00 140.00 125.00 95.00 160.00 150.00 350.00 300.00 45.00 120.00 100.00 90.00 700.00 600.00 500.00 450.00 30.00 200.00 160.00 130.00 95.00 80.00 160.00 140.00 120.00 500.00
134
Code No. 0568 0569 0570 0571 0583 0584 0585 0586 0587 0588 0589 0590 0591 0592 0594 0595 0596 0597 0608 0635 0637 0638 0639 0640 0641 0642 0643
Description Chromium plated brass casement window fastener Chromium plated Brass casement stays (straight peg type ) 300 mm weighing not less than 0.33 kg Chromium plated Brass casement stays (straight peg type ) 250 mm weighing not less than 0.28 kg Chromium plated Brass casement stays (straight peg type ) 200 mm weighing not less than 0.24 kg Chromium plated Brass Night latch Chromium plated Brass Wardrobe Knob 50 mm Chromium plated Brass screws 50 mm Chromium plated Brass screws 40 mm Chromium plated Brass screws 30 mm Chromium plated Brass screws 25 mm Chromium plated Brass screws 20 mm Chromium plated Brass curtain rod 12 mm dia 1.25 mm thick Chromium plated Brass curtain rod 20 mm dia 1.25 mm thick Chromium plated Brass curtain rod 25 mm dia 1.25 mm thick Bright finished or black enameled mild steel butt hinges 125x65x2.12 mm Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm Bright finished or black enameled mild steel butt hinges 75x47x1.70 mm Bright finished or black enameled mild steel butt hinges 50x37x1.50 mm Nickel plated bright finished mild steel piano hinges 1 mm thick 25 mm wide Bright finished or black enameled mild steel screws 50 mm Bright finished or black enameled mild steel screws 40 mm Bright finished or black enameled mild steel screws 30 mm Bright finished or black enameled mild steel screws 25 mm Bright finished or black enameled mild steel screws 20 mm Bright finished or black enameled mild steel bolts and nuts 50x6 mm Oxidised mild steel butt hinges 125x65x2.12 mm Oxidised mild steel butt hinges 100x58x1.90 mm
Unit each each each each each each 100 nos 100 nos 100 nos 100 nos 100 nos metre metre metre 10 nos 10 nos 10 nos 10 nos metre 100 nos 100 nos 100 nos 100 nos 100 nos each 10 nos 10 nos
Rate 90.00 140.00 120.00 100.00 500.00 45.00 230.00 190.00 150.00 115.00 100.00 180.00 250.00 330.00 130.00 80.00 60.00 45.00 35.00 60.00 50.00 40.00 30.00 25.00 5.00 130.00 80.00
135
Code No. 0644 0645 0646 0647 0648 0649 0650 0651 0652 0653 0654 0655 0656 0660 0661 0662 0663 0664 0665 0666 0667 0668 0669 0670 0679 0680 0681 0682 0683 0684 0685 0686
Description Oxidised mild steel butt hinges75x47x1.70 mm Oxidised mild steel butt hinges50x37x1.50 mm Oxidised mild steel parliamentary hinges150x125x27x2.8 mm Oxidised mild steel parliamentary hinges 125x125x27x2.8 mm Oxidised mild steel parliamentary hinges 100x125x27x2.8 mm Oxidised mild steel parliamentary hinges 75x100x20x2.24 mm Oxidised mild steel single acting spring hinges 150 mm Oxidised mild steel single acting spring hinges 125 mm Oxidised mild steel single acting spring hinges 100 mm Oxidised mild steel double acting spring hinges 150 mm Oxidised mild steel double acting spring hinges 125 mm Oxidised mild steel double acting spring hinges 100 mm Nickel plated mild steel piano hinges 1 mm thick 35 mm wide Oxidised mild steel sliding door bolt 300x16 mm Oxidised mild steel sliding door bolt 250x16 mm Oxidised mild steel door latch 300x20x6 mm Oxidised mild steel door latch 250x20x6 mm Oxidised mild steel tower bolt (barrel type) 250x10 mm Oxidised mild steel tower bolt (barrel type) 200x10 mm Oxidised mild steel tower bolt (barrel type) 150x10 mm Oxidised mild steel tower bolt (barrel type) 100x10 mm Oxidised mild steel handles 125 mm Oxidised mild steel handles 100 mm Oxidised mild steel handles75 mm Oxidised mild steel hasps and staples(safety type) 150 mm Oxidised mild steel hasps and staples(safety type) 115 mm Oxidised mild steel hasps and staples(safety type) 90 mm Oxidised mild steel screws 50 mm Oxidised mild steel screws 40 mm Oxidised mild steel screws 30 mm Oxidised mild steel screws 25 mm Oxidised mild steel screws 20 mm
Unit 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each each each each each each metre each each each each each each each each each each each 10 nos 10 nos 10 nos 100 nos 100 nos 100 nos 100 nos 100 nos
Rate 55.00 45.00 320.00 300.00 225.00 190.00 105.00 100.00 80.00 110.00 105.00 85.00 40.00 90.00 80.00 45.00 40.00 40.00 35.00 25.00 20.00 17.00 15.00 14.00 120.00 100.00 75.00 70.00 50.00 45.00 35.00 30.00
136
Code No. 0687 0688 0689 0690 0691 0692 0693 0694 0696 0697 0698 0699 0700 0701 0702 0703 0704 0705 0706 0713 0714 0715 0717 0718 0719 0752 0753
Description Anodised Aluminium butt hinges 125x75x4 mm Anodised Aluminium butt hinges 125x63x4 mm Anodised Aluminium butt hinges 100x75x4 mm Anodised Aluminium butt hinges 100x63x3.2 mm Anodised Aluminium butt hinges 100x63x4 mm Anodised Aluminium butt hinges 75x63x4 mm Anodised Aluminium butt hinges 75x63x3.2 mm Anodised Aluminium butt hinges 75x45x3.2 mm Anodised Aluminium sliding door bolt 300x16 mm Anodised Aluminium sliding door bolt 250x16 mm Anodised Aluminium tower bolt (barrel type)300x10 mm Anodised Aluminium tower bolt (barrel type)250x10 mm Anodised Aluminium tower bolt (barrel type)200x10 mm Anodised Aluminium tower bolt (barrel type)150x10 mm Anodised Aluminium tower bolt (barrel type)100x10 mm Anodised Aluminium handles 125 mm with plate 175 x 32 mm Anodised Aluminium handles 100 mm with plate 150 x 32 mm Anodised Aluminium handles 75mm with plate 125 x 32 mm Anodised Aluminium kicking plate 50 cm long100x3.15 mm Block board construction flush door with teak wood ply on both faces 35 mm thick Block board construction flush door with teak wood ply on both faces 30 mm thick Block board construction flush door with teak wood ply on both faces 25 mm thick Block board construction flush door with commercial ply on both faces 35 mm thick Block board construction flush door with commercial ply on both faces 30 mm thick Block board construction flush door with commercial ply on both faces 25 mm thick Block board construction flush door lipping Square vision panel (upto 0.10 sqm) in Block board construction flush door
Unit 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each each 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos each sqm sqm sqm sqm sqm sqm sqm of door area sqm of door area
Rate 550.00 510.00 500.00 480.00 490.00 475.00 450.00 390.00 155.00 125.00 700.00 580.00 450.00 360.00 280.00 470.00 360.00 300.00 125.00 1,600.00 1,450.00 1,300.00 1,100.00 950.00 850.00 280.00 110.00
137
Code No. 0754 0755 0757 0759 0763 0834 0869 1003 1008 1015 1021 1022 1189 1190 1199 1211 1231 1238 2204 2205 2406 2407 2412 2449 2451 2452 2453
Description Circular vision panel (upto 0.10 sqm) in Block board construction flush door Decorative type Louvers (upto 0.20 sqm) in Block board construction flush door Rebate cutting in Block board construction flush door Decorative plywood 4 mm Glue Synthetic enamel paint in all shades except black or chocolate shade Plaster of Paris Mild steel round bar above 12 mm dia Flats up to 10 mm in thickness Mild steel expanded metal 20x60 mm strands Hard drawn steel wire fabric Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots Second class teak wood in scantling Second class teak wood in planks Sal wood in scantling G.I. plain washer for seam bolts Extra for selected planks of second class teakwood Extra for selected planks of first class teakwood Carriage of Timber Carriage of Steel Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm). Float glass sheet of nominal thickness 5.5 mm.(weight not less than 13.50 kg/sqm) Ply wood 5 ply with commercial ply on both faces 6 mm thick Oxidised mild steel pull bolt lock (locking bolt) of size 85 mm x 42 mm with screws, bolts, nuts and washers complete Brass cupboard lock 6 levers of approved quality 40 mm size Brass cupboard lock 6 levers of approved quality 50 mm size Brass cupboard lock 6 levers of approved quality 65 mm size
Unit sqm of door area sqm of door area sqm of door area sqm kilogram litre kilogram quintal quintal sqm sqm 10 nos 10 cudm 10 cudm 10 cudm 100 nos 10 cudm 10 cudm cum tonne sqm sqm sqm each each each each
Rate 170.00 290.00 80.00 400.00 65.00 135.00 4.00 4,000.00 4,200.00 270.00 430.00 20.00 640.00 720.00 500.00 32.00 115.00 140.00 100.11 77.87 310.00 450.00 340.00 44.00 65.00 70.00 75.00
138
Code No. 2454 2455 2456 2459 2464 2465 2466 2468 2469 2470 2471 2480 2481 2483 2504 2505 7001 7003 7018 7019 7020 7021 7023 7029 7032 7033 7034
Description Brass cupboard lock 6 levers of approved quality 75 mm size Brass hanging type door stopper 150 mm Hydraulic door closer bottle type M.S. body with necessary accessories and screws complete Anodised Aluminium hanging type door stopper Anodised Aluminium pull bolt lock (locking bolt) of size 85 mmx42 mm with screws, bolts, nuts and washers complete Anodised Aluminium Casement stay 250 mm Hollock wood in scantling Nickeled Chromium Brass cupboard lock 40 mm size Nickeled Chromium Brass cupboard lock 50 mm size Nickeled Chromium Brass cupboard lock 65 mm size Nickeled Chromium Brass cupboard lock 75 mm size Ply wood 5 ply with teak ply on both faces 9 mm thick Ply wood 5 ply with teak ply on one face and commercial ply on another face 9 mm thick Ply wood 7 ply with teak ply on one face and commercial ply on another face 9 mm thick Kiln seasoning of timber Hollock wood in planks Brass 100mm mortice latch and lock with 6 levers without pair of handles Pair of Anodised Aluminium lever handles for 100 mm mortice latch and lock Joint tape roll Dash fastener/Chemical Fastener All drive screws ( for gypsum board) Primer ( for gypsum board) Chromium plated brackets ( curtain rods) Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) Nickel plated M.S. pipe 25 mm dia Nickel plated M.S. pipe 20 mm dia
Unit each each each each each each 10 cudm each each each each sqm sqm sqm cum 10 cudm each each roll each 100 nos litre each sqm sqm metre metre
Rate 95.00 60.00 535.00 21.00 46.00 46.00 310.00 62.00 70.00 82.00 103.00 960.00 775.00 845.00 680.00 350.00 250.00 300.00 140.00 13.00 56.00 85.00 7.00 230.00 315.00 75.00 67.00
139
Code No. 7035 7036 7040 7042 7043 7048 7049 7055 7056 7059 7060 7063 7064 7065 7137
Description Nickel plated M.S. Brackets for curtain rod 20 mm Nickel plated M.S. Brackets for curtain rod 25 mm Oxidised mild steel screws 35 mm Mild steel conduit pipe (heavy type) ISI marked-20 mm dia Mild steel conduit pipe (heavy type) ISI marked-25 mm dia Rawl plug 50 mm (designation 10 nos.) Teak wood lipping of size 25x3 mm in pelmets Flat pressed 3 layer and graded particle board (medium density) Grade 1 conforming to IS : 3087 - 18 mm thick Aluminium tee channel (heavy duty) with rollers and stop end Aluminium hanging floor door stopper with twin rubber & stopper Hydraulic door closer tubular type Aluminium section body Oxidised M.S. casement stay (straight peg type) 300 mm not less than 0.33 kg Oxidised M.S. casement stay (straight peg type) 250 mm not less than 0.28 kg Oxidised M.S. casement stay (straight peg type) 200 mm not less than 0.24 kg Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick plain type-I, medium density flat pressed three layer, graded particle board (FPT-I) as per IS : 3087 bonded with BWP type synthetic resin adhesive, as per IS : 848 Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick both sides prelaminated type-I, medium density flat pressed three layer, graded particle board (FPT-I) as per IS : 3087 bonded with BWP type synthetic resin adhesive, as per IS : 848 Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of 12 mm thick one side prelaminated type-I, and other side balancing lamination, medium density flat pressed three layer, graded particle board (FPT-I) as per IS : 3087 bonded with BWP type synthetic resin adhesive, as per IS : 848 Factory made 30 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of sheet glass using 10 kg/ sqm glass panes Factory made 35 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15 : 1995 and panels of galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm
Unit each each 100 nos metre metre each metre sqm metre each each each each each
Rate 6.00 7.00 40.00 57.00 66.00 10.00 20.00 390.00 45.00 58.00 810.00 21.00 18.00 17.00
sqm
1,780.00
7139
sqm
1,930.00
7143
sqm
1,850.00
7151
sqm
1,580.00
7154
sqm
1,630.00
140
Description Factory made 30 mm thick shutters with laminated veneer lumber styles & rails as per TADS 15:1995 and panels of galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm Laminated veneer lumber confirming to TADS 15:1995 manufactured in factory in frames of doors, windows Oxidised M.S. safety chain (weighing not less than 450 gms) for door 25 mm thick particle board IInd class teak wood lipping 25 mm wide x 12 mm thick 25 mm thick melamine faced prelaminated three layer particle board For flush door shutters Extra for providing teak veneering on one side instead of commercial veneering Expandable fastener with plastic sleeve and M.S. screws : 25 mm long Expandable fastener with plastic sleeve and M.S. screws : 32 mm long Expandable fastener with plastic sleeve and M.S. screws : 40 mm long Expandable fastener with plastic sleeve and M.S. screws : 50 mm long 12 mm M.S. 'U' beading Glass reinforced Gypsum ( GRG) board 12.5 mm thick Galvanised M.S. sheet 0.5 mm thick pressed channel section of size 50x32 mm Galvanised M.S. sheet 0.50 mm thick pressed stud : 48x34x36 mm Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt Aluminium single cleat of size 30x32x3 mm Aluminium grip strip of size 50x12x2 mm 25 mm thick prelaminated flush door shutter both side decorative Aluminium U beading Glass sheet (Pin headed) 4 mm thick Veneered particle board with commercial veneering on both sides 12 mm thick Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade), 12 mm thick Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade), 18 mm thick
Unit
Rate
sqm 10 cudm each sqm metre sqm sqm each each each each metre sqm metre metre each each each sqm kilogram sqm sqm
1,385.00 665.00 60.00 460.00 39.00 870.00 320.00 8.00 9.00 12.00 14.00 14.00 230.00 60.00 72.00 48.00 13.00 10.00 790.00 208.00 255.00 480.00
7157 7184 7269 7271 7272 7307 7312 7313 7314 7315 7349 7366 7367 7369 7388 7443 7444 7445 7449 7451 7468 7477
sqm
690.00
7478
sqm
810.00
141
Description Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade), 25 mm thick Prelaminated particle board with both sides decorative lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade), 12 mm thick Oxidised M. S. hinges finished with nickel plating 50 mm (Over all width) Oxidised M. S. hinges finished with nickel plating 65 mm (Over all width) PTMT- handle 125x34x24 mm PTMT -handle 150x34x24 mm PTMT- butt hinges 75x60x10 mm PTMT- butt hinges 100x75x10 mm PTMT -Tower bolt 152x42x18 mm PTMT- Tower bolt 202x42x18 mm PTMT - door catcher 72x42 mm Coir veneered board 4 mm thick Coir veneered board 6 mm thick Coir veneered board 12 mm thick Coir veneered board 18 mm thick 24 mm thick Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish 30 mm thick Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish Factory made PVC rigid foam panelled shutter i/c carriage Factory made PVC rigid foam panelled shutter as per IS : 4020 i/c carriage Factory made PVC rigid foam sheet 1mm thick 48 mmX40 mmX1.5 mm thick Factory made door frame of PVC extruded sections in white, grey or wooden finish Factory made door frame PVC extruded sheet i/c carriage Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm Stainless steel screws 50 mm Stainless steel screws 40 mm Stainless steel screws 30 mm
Unit
Rate
sqm
880.00
7480
sqm metre metre each each each each each each each sqm sqm sqm sqm sqm sqm sqm sqm sqm metre metre 10 nos 100 nos 100 nos 100 nos
720.00 39.00 49.00 30.00 34.00 42.00 56.00 65.00 80.00 27.00 272.00 367.00 622.00 950.00 2,025.00 2,125.00 2,025.00 2,420.00 173.00 142.00 330.00 79.00 240.00 195.00 145.00
7485 7486 7512 7513 7514 7515 7516 7517 7518 7552 7553 7555 7556 8001 8002 8003 8004 8006 8010 8011 8100 8210 8211 8212
142
Code No. 8214 8215 8216 8217 8218 8219 8220 8221 8222 8223 8224 8225 8678 8699 8700 8703 8704 8705 8706 8707 8708 8710 8711 8713 8714 8715 8716 8717
Description Stainless steel screws 20 mm Stainless steel butt hinges 125x64x1.9 mm IS : 12817 marked Stainless steel butt hinges 100x58x1.9 mm IS : 12817 marked Stainless steel butt hinges 75x47x1.8 mm IS : 12817 marked Stainless steel butt hinges 50x37x1.5 mm IS : 12817 marked Stainless steel butt hinges (heavy weight) 125x64x2.5 mm IS : 12817 marked Stainless steel butt hinges (heavy weight) 100x60x2.5 mm IS : 12817 marked Stainless steel bult hinges (heavy weight) 75x50x2.5 mm IS : 12817 marked M.S. heavy weight but hinges 125x90x4.0mm IS : 1341 marked M.S. heavy weight butt hinges 100x75x3.5 mm IS: 1341 marked M.S. heavy weight butt hinges 75x60x3.1 mm IS: 1341 marked M.S. heavy weight butt hinges 50x40x2.5 mm IS : 1341 marked 1mm thick 35mm wide bright finished stainless steel piano hinges 8 mm thick tapered edge calcium silicate board 10 mm thick calcium silicate board Telescopic drawer channels 300mm long Stainless steel roller for sliding arrangement in racks/ cupboards/ cabinets shutter 50mmX42mmX2mm thick Factory made door frame of PVC extruded sections in white, grey or wooden finish 25mm thick factory made PVC flush door shutter i/c carriage Factory made glass reinforced plastic door frame 90x45 mm i/ c carriage 30 mm thick factory made glass fiber reinforced plastic panel door shutter i/c carriage Factory made solid PVC door frame 60 x 30mm i/c carriage 28mm factory made solid PVC panel door shutter i/c carriage Fiber glass reinforced plastic chajja Magnetic catcher triple strip vertical type Magnetic catcher double strip horizontal type 100 mm mortice lock with 6 levers for aluminium door 12.5 mm thick Glass fibre reinforced Gypsum board
Unit 100 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos 10 nos metre sqm sqm set each metre sqm metre sqm metre sqm sqm each each each sqm
Rate 95.00 240.00 215.00 145.00 125.00 320.00 230.00 195.00 320.00 160.00 83.00 70.00 37.00 223.00 370.00 135.00 8.00 135.00 2,050.00 365.00 1,715.00 270.00 2,120.00 3,460.00 15.00 12.00 310.00 160.00
143
Code No. 8719 8720 8721 8722 8723 8724 8725 8726 8727 8730 9999
Description 2nd class teak wood lipping/ moulded beading or Taj beading of size 18X5mm Ceiling sections 0.55 mm thick having a knurled web of 51.55mm and two flanges of 26mm each with lips of 10.55mm Perimeter channel having one flange of 20mm and another flange of 30mm with thickness of 0.55mm and web of length 27mm Nylon sleeves & wooden screws (40mm) Counter sunk ribbed head screw 25mm 12mm thick marine plywood conforming to IS:710 12mm thick fire retardant plywood conforming to IS: 5509 1.5mm thick decorative laminated sheet 1.0mm thick decorative laminated sheet 30 mm thick factory made glass fiber reinforced plastic flush door shutter i/c carriage Sundries NEW CODES
Unit
Rate
metre metre metre each cent sqm sqm sqm sqm sqm L.S.
25.00 39.00 25.00 1.90 72.00 825.00 860.00 475.00 350.00 1,975.00 1.49
Kiln seasoned selected sheesham wood planks 12 mm commercial ply 18 mm thick block board with commercial ply veneering on both side Factory made door frame of size 50x47mm with wall thickness 5 mm made of single piec extruded profile 30 mm thick factory made solid PVC profile panelled door single piece extruded profile decorative finish (wood grain printed on both side) 30 mm thick factory made solid PVC profile panelled door single piece extruded profile non decorative finish P.V.C. Single piece extruded door frame of profile size 50 mm x 47 mm with wall thickness of 5 mm 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished) 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile decorative finished (wood grain finished) Stainless steel wire guage (Grade-304) aperture 1.4mm and 0.50 mm dia wire Factory made door frame fire rated ( 60 minutes) made with 16 SWG G.I. Sheet of section 143 mm x 57 mm duly filled with vermuculite based concrete mix
metre
978.00
144
Description Fire rated door shuttere made with 16 SWG G.I. sheet( 60 minutes) without panel Fire seal Putty Clear fire resistant glass panes 6mm thick (60 minutes) G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/m2) with ceramic tape of suitable thickness and fire resistant primer coating Matrix Mineral Board Panic Bar / latch (Double point) 65 mm x 55 mm x 2 mm thick Factory made door frame of PVC extruded section in white, grey or wooden finish 37 mm thick Factory made shutter with style,rails and panels of PVC extruded section in white or grey finish i/c carriage 75 mm x 53 mm x 2.0 mm thick Factory made door frame of PVC extruded section in white, grey or wooden finish 37 mm thick Factory made fusion welded shutter with style, rails and panels of PVC extruded section in wooden finish Zinc alloy (white powder coated) casement handle for uPVC windows Zinc alloy (white powder coated) Touch Lock for uPVC windows Zinc alloy rollers for uPVC windows Zinc alloy rollers for uPVC door Zinc alloy (white powder coated) casement lock for uPVC windows Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 300 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 350 mm x 19 x 1.9 mm for uPVC windows Stainless steel friction hinge of size 400 mm x 19 x 1.9 mm for uPVC windows uPVC extruded profile casement window Frame (50 mm x 50 mm) uPVC extruded profile casement window sash (Style and Rail) (62 mm x 34 mm) uPVC extruded profile casement window mullion (intermediate section) (66 mm x 50 mm)
Unit
Rate
sqm kg sqm
metre metre each metre sqm metre sqm each each each each each each each each each each metre metre metre
247.00 61.85 5,000.00 318.00 2,225.00 327.00 2,300.00 150.00 100.00 50.00 80.00 100.00 225.00 275.00 350.00 400.00 500.00 158.00 145.00 175.00
8743 8744 8745 8746 8747 8748 8750 8751 8752 8753 8754 8755 8756 8757 8758 8759 8760 8761 8762
145
Code No. 8763 8764 8765 8766 8767 8768 8769 8770 8771 8772 8773 8775
Description uPVC extruded profile casement window 'T' profile (one vertical length in between two shutters) (24 mm x 34.5 mm) uPVC extruded profile casement window glazing bead (12 mm x 18 mm) uPVC extruded profile casement window Frame ( 67 mm x 62 mm) uPVC extruded profile casement Window Sash / Mullion ( 67 mm x 75 mm)(Style,rail and intermediate section) uPVC extruded profile casement window glazing bead (35 mm x 18 mm) uPVC extruded profile Two Track Sliding frame (67 mm x 52 mm) uPVC extruded profile Sliding window Sash (60 mm x 44 mm) uPVC extruded profile Sliding Interlock for Window (one vertical length in each shutter) (45.5 mm x 28 mm) uPVC extruded profile Sliding Door Sash (80 mm x 44 mm) Aluminium Track on bottom rail for uPVC window Wool Pine for uPVC window Steel Galvanised tubular reinforcement for uPVC door/ window
Unit
Rate
metre metre metre metre metre metre metre metre metre metre metre metre
46.00 46.00 225.00 250.00 78.00 235.00 212.00 45.00 275.00 20.00 15.00 50.00
146
Providing laminated veneer lumber conforming to IS:14616 and TAD -15: 2001( Part B) in factory made frames of doors, windows, clerestory windows and other frames, wrought framed and fixing in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : 9.3.1 9.3.2 Sal wood Kiln seasoned and chemically treated hollock wood
cum
86,951.10
9.3
cum cum
65,549.90 43,393.20
9.4
Extra for additional labour for circular works, such as in frames of fan light : 9.4.1 9.4.2 9.4.3 Second class teak wood Sal wood Kiln seasoned and chemically treated hollock wood cum cum cum 8,581.10 6,865.00 4,661.45
9.5
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. 9.5.1 9.5.1.1 9.5.1.2 9.5.2 9.5.2.1 9.5.2.2 9.5.3 9.5.3.1 9.5.3.2 Second class teak wood 35 mm thick shutters 30 mm thick shutters Kiln seasoned and chemically treated hollock wood 35 mm thick shutters 30 mm thick shutters Kiln seasoned selected planks of sheesham wood 35 mm thick shutters 30 mm thick shutters sqm sqm 2,260.70 2,000.75 sqm sqm 1,445.30 1,310.60 sqm sqm 2,434.05 2,162.65
9.6
Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S. pressed butt hinges bright finished of required
147
Code No.
Description size with necessary screws, all complete as per directions of Engineerin-charge and panelling with panels of : 9.6.1 12 mm thick plain grade - 1, medium density flat pressed three layer particle board FPT - I or graded wood particle board FPTI, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848 : 12 mm thick pre-laminated particle board (decorative lamination on both sides) grade - 1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPTI, conforming to IS : 3087, bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade 1, Type - II marked : 12 mm thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1 medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade -1, Type II marked :
Unit
Rate
sqm
2,300.75
9.6.2
sqm
2,475.00
9.6.3
sqm
2,382.10
9.7
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 9.7.1 9.7.2 9.7.3 9.7.3.1 9.7.3.2 Second class teak wood Kiln seasoned and chemically treated hollock wood Ply wood 5 ply, 9 mm thick Decorative plywood both side decorative veneer (Type - I) conforming to IS 1328 BWR type Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type Ply wood 7 ply, 9 mm thick Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type Particle Board 12 mm thick Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked Veneered flat pressed three layer or graded wood particle board with commercial veneering on both sides conforming to IS:3097, grade I sqm 775.85 sqm 1,669.85 sqm sqm 1,950.35 1,149.35
sqm
1,409.40
9.7.4 9.7.4.1
sqm
1,507.95
sqm
994.10
9.7.5 .3 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked 9.7.5.4 Pre-laminated particle board with decorative lamination on both sides, Grade I, Type II, IS:12823 marked
sqm sqm
1,289.75 1,332.00
148
Code No.
Description 9.7.6 9.7.6.1 9.7.7 9.7.7.1 9.7.7.2 9.7.8 Coir Veneer Board (conforming to IS 14842) 12 mm thick Float glass panes 4 mm thick glass pane 5.5 mm thick glass panes Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching wood beading
Unit
Rate
sqm
1,339.90
9.8 9.9
Deleted. Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 9.9.1 9.9.1.1 9.9.1.2 9.9.2 9.9.2.1 9.9.2.2 9.9.3 9.9.3.1 9.9.3.2 Second class teak wood 35 mm thick 30 mm thick Kiln seasoned and chemically treated hollock wood 35 mm thick 30 mm thick Kiln seasoned selected planks of sheesham wood 35 mm thick 30 mm thick sqm sqm 2,758.75 2,475.80 sqm sqm 1,830.40 1,676.50 sqm sqm 2,955.90 2,645.70
9.10
Providing and fixing factory made laminated veneer lumber glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick float glass panes for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, all as per directions of Engineer-in-charge. 9.10.1 30 mm thick shutters sqm 2,068.45 Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) 9.11.1 5.5 mm thick instead of 4 mm thick. sqm 162.60 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). Deduct for providing pin headed glass panes instead of ordinary float glass panes weighing 4 mm thick in doors, windows and clerestory windows shutters (Area of opening for glass panes excluding portion inside rebate shall be measured). Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured). Deduct for not providing hinges in doors, windows or clerestory window shutters with : 9.15.1 Stainless steel butt hinges with stainless steel screws :
9.11
9.12
sqm
5.80
9.13
sqm
63.90
9.14
sqm
97.45
9.15
149
Code No.
Description 9.15.1.1 For 2nd class teak wood and other class of wood shutters 9.15.2 ISI marked M.S. pressed butt hinges bright finished of required size
Unit sqm
Rate 142.05
9.15.2.1 For 2nd class teak wood and other class of wood shutters 9.16 Providing and fixing 25 mm thick shutters for cup board etc. : 9.16.1 Panelled or panelled & glazed shutters : 9.16.1.1 Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws 9.16.1.2 Second class teak wood including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws 9.16.2 Glazed shutters : 9.16.2.1 Second class teak wood including ISI marked anodized aluminium butt hinges with necessary screws 9.16.2.2 Second class teak wood including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws 9.17 Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) : 9.17.1 9.17.2 9.18 12 mm thick 18 mm thick
sqm
44.65
sqm sqm
2,440.25 2,457.15
sqm sqm
2,463.25 2,423.35
sqm sqm
488.10 568.95
Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 9.18.1 9.18.2 18 mm thick 25 mm thick sqm sqm 1,099.80 1,187.80
9.19 9.20
Deleted Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 9.20.2 9.20.3 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws sqm sqm 2,159.05 1,984.80
sqm
1,789.45
9.21
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply
150
Code No.
Description veneering with vertical grains or cross bands and face veneers on both faces of shutters : 9.21.1 9.21.2 9.21.3 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws
Unit
Rate
9.22
Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) 9.22.1 On one side only sqm 371.70 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : 9.24.1 9.24.2 Rectangular or square Circular sqm sqm 127.75 197.45
9.23
sqm
325.20
9.24
9.25
Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door shutters to be measured). 9.25.1 Decorative type door sqm sqm 336.85 92.90 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 9.27.1 9.27.1.1 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size sqm sqm sqm sqm sqm sqm 2,737.90 1,741.20 2,563.20 2,835.35 1,838.65 2,660.65
9.26 9.27
9.27.1.1.1 Second class teak wood 9.27.1.1.2 Kiln seasoned and chemically treated hollock wood 9.27.1.1.3 Kiln seasoned selected class of sheesham wood 9.27.1.2 With ISI marked stainless steel butt hinges of required size 9.27.1.2.1 Second class teak wood 9.27.1.2.2 Kiln seasoned and chemically treated hollock wood 9.27.1.2.3 Kiln seasoned selected class of sheesham wood 9.27.2 9.27.2.1 30 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size
9.27.2.1.1 Second class teak wood 9.27.2.1.2 Kiln seasoned and chemically treated hollock wood
SUBHEAD -9.0 WOOD AND PVC WORK
sqm sqm
2,412.70 1,560.65
151
Code No.
Description 9.27.2.1.3 Kiln seasoned selected class of sheesham wood 9.27.2.2 With ISI marked stainless steel butt hinges of required size 9.27.2.2.1 Second class teak wood 9.27.2.2.2 Kiln seasoned and chemically treated hollock wood 9.27.2.2.3 Kiln seasoned selected class of sheesham wood
Deleted. Deleted. Deleted. Providing and fixing wire gauge laminated veneer lumber shutters conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per IS :1568, for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, as per directions of Engineer-in-charge: 9.31.1 9.31.2 35 mm thick shutters 30 mm thick shutters sqm sqm 2,126.55 1,842.00
MISCELLANEOUS - WOOD WORK 9.32 Providing 50x50x50 mm 2nd class teak wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement : 3 fine sand) and making good the walls etc. Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. 9.33.1 9.33.2 9.33.3 9.33.4 9.34 25 mm long 32 mm long 40 mm long 50 mm long each each each each 12.90 14.95 18.45 20.75
each
17.40
9.33
Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 9.34.1 9.34.2 9.34.3 9.34.4 40 mm thick 25 mm thick 20 mm thick 12 mm thick sqm sqm sqm sqm 4,525.00 2,922.80 2,361.20 1,506.70
9.35
Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete : 9.35.1 9.35.2 9.35.3 12 mm thick 18 mm thick 25 mm thick sqm sqm sqm 1,059.90 1,213.25 1,302.65
152
Description Providing and fixing specified wood frame work consisting of battens 50x25 mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. 9.36.1 Kiln seasoned and chemically treated hollock wood
Unit
Rate
cum
84,413.10
9.37
Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : 9.37.1 Decorative veneer facings of approved manufacture sqm 975.15 Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete. Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and priming coat on unexposed surface complete : 9.39.1 9.39.2 18 mm thick 25 mm thick sqm sqm 1,395.40 1,484.80
9.38
sqm
796.70
9.39
9.40
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 9.40.1 2nd class teak wood metre metre metre metre 98.40 135.70 70.05 88.40 9.40.1.1 50x12 mm 9.40.1.2 50 x 20 mm 9.40.2 Kiln seasoned and chemically treated hollock wood 9.40.2.1 50x12 mm 9.40.2.2 50x20 mm
9.41
Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm beading complete with : 9.41.1 Second class teak wood sqm 1,589.10 Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete. Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.
9.42
metre
298.45
9.43
metre
406.75
153
Description Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm thick 150mm wide. 9.44.1 9.44.2 Non decorative veneer on both sides Particle board with decorative veneering on both sides
Unit
Rate
9.45 9.46
Providing and fixing teak wood lipping of size 25x3 mm in pelmet. Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 9.46.1 9.46.2 9.46.3 12 mm dia 20 mm dia 25 mm dia
9.47
Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 9.47.1 9.47.2 20 mm dia (heavy type) 25 mm dia (heavy type) metre metre 107.10 117.55
9.48
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 9.48.2 Fixed to steel windows by welding Fixed to openings /wooden frames with rawl plugs screws etc. kg kg 90.75 98.20
9.49
Providing and fixing expanded metal 20x60 mm strands 3.25 mm wide and 1.6 mm thick for windows etc. including 62 x19 mm beading of II nd class teak wood and priming coat with approved steel primer all complete. Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 9.51.1 9.51.2 With 2nd class teak wood beading 62X19 mm With 12 mm mild steel U beading
sqm
837.95
9.50
sqm
1,033.85
9.51
sqm sqm
758.20 484.75
9.52
Deduct for fixing 75x25 mm hard drawn steel wire fabric of weight not less than 7.75 Kg per sqm in panelled and glazed door and window shutter instead of glass sheet 4 mm thick. Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Providing beams including hoisting, fixing in position and applying wood preservative for the unexposed surfaces, etc. complete with : 9.54.1 9.54.2 Sal wood Hollock wood
sqm
139.40
9.53
each
96.75
9.54
cum cum
63,829.70 41,315.00
154
Code No.
Unit
Rate
9.55
Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 9.55.1 9.55.2 9.55.3 9.55.4 125x65x2.12 mm 100x58x1.90 mm 75x47x1.70 mm 50x37x1.50 mm each each each each 28.15 21.45 17.10 9.10
9.56
Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : 9.56.1 9.56.2 9.56.3 9.56.4 125x90x4.00 mm 100x75x3.50 mm 75x60x3.10 mm 50x40x2.50 mm each each each each 50.25 30.70 19.75 12.00
Note: - In coastal areas, M.S. heavy weight butt hinges or stainless steel hinges shall be used. COPER OXIDISED MILD STEEL FITTINGS (COPPER OXIDISED AS PER IS: 1378) 9.57 Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. 9.57.1 9.57.2 9.57.3 9.57.4 9.58 125x65x2.12 mm 100x58x1.90 mm 75x47x1.70 mm 50x37x1.50 mm each each each each 29.25 21.45 16.85 9.30
Providing and fixing ISI marked oxidised M.S. pressed Parliamentary hinges with necessary screws etc. complete : 9.58.1 9.58.2 9.58.3 9.58.4 150x125x27x2.80 mm 125x125x27x2.80 mm 100x125x27x2.80 mm 75x100x20x2.24 mm each each each each 50.75 48.40 39.70 34.15
9.59
Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete : 9.59.1 9.59.2 9.59.3 150 mm 125 mm 100 mm each each each 147.35 141.55 116.45
9.60
Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete. 9.60.1 9.60.2 9.60.3 150 mm 125 mm 100 mm each each each 153.15 147.35 122.25
9.61
Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. 9.61.1 Overall width 35 mm metre 130.25
155
Code No.
9.62
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 9.62.1 9.62.2 300x16 mm 250x16 mm each each 142.35 129.85
9.63
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 9.63.1 9.63.2 9.63.3 9.63.4 250x10 mm 200x10 mm 150x10 mm 100x10 mm each each each each 55.50 48.50 35.80 29.40
9.64
Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete. Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : 9.65.1 9.65.2 300x20x6 mm 250x20x6 mm
each
60.15
9.65
each each
60.35 54.55
9.66
Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 9.66.1 9.66.2 9.66.3 125 mm 100 mm 75 mm each each each 23.75 21.25 20.10
9.67
Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 9.67.1 9.67.2 9.67.3 150 mm 115 mm 90 mm each each each 20.05 17.30 14.40
9.68
Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 9.68.1 9.68.2 9.68.3 300 mm weighing not less than 200 gms 250 mm weighing not less than 150 gms 200 mm weighing not less than 120 gms each each each each 29.80 25.85 24.70 75.45
9.69
Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors, (weighting not less than 450 gms). STAINLESS STEEL FITTINGS Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 9.70.1 9.70.2 9.70.3 9.70.4 125x64x1.90 mm 100X58X1.90 mm 75x47x1.80 mm 50x37x1.50 mm
9.70
156
Description Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 9.71.1 9.71.2 9.71.3 125x64x2.50 mm 100x60x2.50 mm 75x50x2.50 mm
Unit
Rate
BRASS FITTINGS 9.72 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 9.72.1 9.72.2 9.72.3 9.72.4 9.72.5 9.72.6 9.72.7 9.73 125x85x5.5 mm (heavy type) 125x70x4 mm (ordinary type) 100x85x5.5 mm (heavy type) 100x70x4 mm (ordinary type) 75x65x4 mm (heavy type) 75x40x2.5 mm (ordinary type) 50x40x2.5 mm (ordinary type) each each each each each each each 368.45 124.55 325.10 98.60 121.85 63.75 27.15
Providing and fixing bright finished brass parliamentary hinges with necessary screws etc. complete : 9.73.1 9.73.2 9.73.3 9.73.4 150x125x27x5 mm 125x125x27x5 mm 100x125x27x5 mm 75x100x20x3.2 mm each each each each 326.25 291.40 256.55 204.30
9.74
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.1 9.74.2 9.74.3 9.74.4 250x10 mm 200x10 mm 150x10 mm 100x10 mm each each each each 280.70 219.30 178.65 117.55
9.75
Providing and fixing bright finished brass door latch with necessary screws etc. complete : 9.75.1 9.75.2 300x16x5 mm 250x16x5 mm each each 200.60 189.00
9.76
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 9.79.1 40 mm
each
472.25
9.77
each each
414.20 588.40
9.78 9.79
each
141.25
157
Code No.
9.80 9.81
Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws. Providing and fixing bright finished brass handles with screws etc. complete : 9.81.1 9.81.2 9.81.3 125 mm 100 mm 75 mm
9.82 9.83
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete. Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete : 9.86.1 9.86.2 9.86.3 300 mm weighing not less than 330 gms 250 mm weighing not less than 280 gms 200 mm weighing not less than 240 gms
each
662.80
9.84
each each
981.75 60.35
9.85 9.86
9.87
Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 9.87.1 9.87.2 9.87.3 150 mm 115 mm 90 mm each each each 93.25 79.30 67.70
CHROMIUM PLATED BRASS FITTINGS 9.88 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete. Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. 9.90.1 9.90.2 9.90.3 9.90.4 Size 40 mm Size 50 mm Size 65 mm Size 75 mm each each each each 137.75 147.05 161.00 185.35
each each
646.50 646.50
9.89 9.90
158
Description Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete. Providing and fixing chromium plated brass handles with necessary screws etc. complete: 9.92.1 9.92.2 9.92.3 125 mm 100 mm 75 mm
Unit
Rate
each
57.65
9.93 9.94
Providing and fixing chromium plated brass casement window fastener with necessary screws etc. complete. Providing and fixing chromium plated brass casement stays (straight peg type) with necessary screws etc. complete : 9.94.1 9.94.2 9.94.3 300 mm weighing not less than 330 gms 250 mm weighing not less than 280 gms 200 mm weighing not less than 240 gms
ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI MARKED) 9.95 Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 9.95.1 9.95.2 9.95.3 9.95.4 9.95.5 9.95.6 9.95.7 9.95.8 125x75x4 mm 125x63x4 mm 100x75x4 mm 100x63x4 mm 100x63x3.2 mm 75x63x4 mm 75x63x3.2 mm 75x45x3.2 mm each each each each each each each each 98.70 94.05 83.70 82.50 81.35 73.40 70.50 63.55
Note :- Aluminum hinges shall not be used in wooden shutters, stainless steel hinges shall be preferred. 9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1 9.96.2 9.97 300x16 mm 250x16 mm each each 203.80 168.95
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.1 9.97.2 9.97.3 9.97.4 9.97.5 300x10 mm 250x10 mm 200x10 mm 150x10 mm 100x10 mm each each each each each 100.40 86.45 71.05 59.00 46.25
9.98
Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed
159
Code No.
Description to required colour and shade, with necessary screws bolts, nut and washers etc. complete.
Unit
Rate
each
62.45
9.99
Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.100.1 125 mm 9.100.2 100 mm 9.100.3 75 mm
each
155.35
9.100
9.101
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 9.101.1 Single rubber stopper 9.101.2 Twin rubber stopper each each 28.60 71.55
9.102
Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. Providing and fixing aluminium tee channels (heavy duty) with rollers & stop end in pelmets as curtain rod. GYPSUM BOARD PARTITIONS Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher
each
62.40
9.103
each metre
706.15 55.85
9.104
9.105
160
Code No.
Description and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 9.105.1 75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS: 2095: part I 9.105.2 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS: 2095: part I 9.105.3 66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm 9.105.4 66mm overall thickness partition using 8mm thick double skin non- asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS: 14862 with suitable fibre cement screws
Unit
Rate
sqm
1,145.70
sqm
983.10
sqm
1,129.45
9.106
Providing and fixing PTMT handles with necessary screws etc. complete. 9.106.1 125x34x24 mm weighing not less than 23 gms 9.106.2 150x34x24 mm weighing not less than 26 gms
9.107
Providing and fixing PTMT Butt hinges with necessary screws etc. complete. 9.107.1 75x60x10 mm fitted with 5.5 mm dia M.S. Bright Bar Rod weighing not less than 34 gms 9.107.2 100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod weighing not less than 53 gms each each 58.90 77.20
9.108
Providing and fixing PTMT Tower Bolts with 12 mm one piece rod inside and necessary screws etc., complete. 9.108.1 152x42x18 mm weighing not less than 60 gms 9.108.2 202x42x18 mm weighing not less than 78 gms each each each 81.30 100.30 33.60
9.109 9.110
Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms Providing and fixing Bamboo jaffery/ fencing consisting of superior quality 25 mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-charge. Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 9.111.1 50x50 mm (base and height)
sqm
328.90
9.111
metre
170.95
9.112
Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge. Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineerin-charge.
metre
44.15
9.113
each
410.00
161
Description Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 9.114.1 Triple strip vertical type 9.114.2 Double strip (horizontal type)
Unit
Rate
each each
21.90 18.45
9.115
Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineerin-charge. Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance 1mm), with wall thickness 2.0 mm ( 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm ( 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineerin-charge 9.117.1 Extruded section profile size 48x40 mm 9.117.2 Extruded section profile size 42x50 mm
one set
177.50
9.116
each
11.10
9.117
metre metre
185.15 177.05
9.118
Providing and fixing to existing door frames. 9.118.1 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm ( 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ( 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm ( 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 9.118.2 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm ( 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm ( 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter
sqm
2,471.10
162
Code No.
Description frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm ( 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm ( 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturers specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places
Unit
Rate
sqm
2,587.25
sqm
2,500.15
9.119
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturers specification and direction of Engineerin-Charge. Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 9.120.1 30 mm thick plain PVC door shutters 9.120.2 30 mm thick pre laminated PVC door shutters
metre
404.60
9.120
sqm sqm
2,499.20 2,958.00
163
Description Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat . Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. Providing and fixing to existing door frames. 9.122.1 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. 9.122.2 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
Unit
Rate
metre
445.25
9.122
sqm
2,139.15
sqm
2,441.10
9.123
Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement , including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge. Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge. 9.124.1 Non decorative finish 9.124.2 Decorative finish (both side wood grained finish)
metre
334.90
9.124
sqm sqm
2,609.55 3,050.90
9.125
Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.
sqm
632.40
164
Description Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 9.126.1 Marine plywood conforming to IS: 710 9.126.2 Fire retardant plywood conforming to IS: 5509
Unit
Rate
sqm sqm
1,457.70 1,506.25
9.127
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 9.127.1 1.5 mm thick 9.127.2 1.0 mm thick sqm sqm 756.05 596.30
9.128
Providing and fixing factory made Fiberglass Reinforced plastics (F.R.P.) chajja 4 mm thick of required colour, size and design made by Resin Transfer Moulding (RTM) Machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature for easy drainage of water and duly reinforced by 2nos vertically and 1nos horizontally 50x2 mm thick M.S. flat with 12 mm in built hole for grouting on the existing wall along with the 50 mm flanges duly inserted and sealed in the wall complete in one single piece casted monolithically, including all necessary fittings . The FRP Chajja should be manufactured using unsaturated Polyester resin as per IS: 6746, duly reinforced with fibre glass chopped strand mat (CSM) as per IS: 11551 complete with protective Gel coat U/V coating on Top for complete resistance from the extreme of temperature, weather & sunlight. Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. 9.130.1 With decorative veneering on one side and commercial veneering on other side 9.130.2 With non decorative veneering on both sides
sqm
4,560.40
9.129
sqm
1,442.80
9.130
sqm sqm
1,239.50 1,146.60
9.131
Providing and fixing factory made shutters of Pre-laminated particle board flat pressed three layer or graded wood particle board with one side decorative finish and other side balancing lamination conforming to IS: 12823 Grade l Type ll, of approved design, and edges sealed with water resistant paint and lipped with aluminium 'U' type edge beading allround the shutter, including fixing with angle cleat, grip strip, cadmium plated steel screws, including fixing of aluminium hinges 100x63x4 mm etc. complete as per architectural drawing and direction of Engineer-inCharge (Cost of 'U' beading and hinges will be paid for separately). 9.131.1 25 mm thick sqm 1,179.80
165
Description Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge. Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. 9.133.1 Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/ sq.cm, Bending strength 100 kg/sq.cm. 10mm thick Non-asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (high pressure steam cured) as per IS : 14862 with suitable fibre cement screw. 8 mm thick Gypsum board conforming to IS: 2095 Part - I . 12.5 mm thick
Unit
Rate
kg
400.75
9.133
9.133.1.1 9.133.2
sqm
854.55
sqm sqm
644.95 586.15
Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 9.134.1 9. 134.1.1 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size sqm sqm sqm sqm sqm sqm 3,139.75 2,143.05 2,965.05 3,237.20 2,240.50 3,062.50
9. 134.1.1.1 Second class teak wood 9. 134.1.1.2 Kiln seasoned and chemically treated hollock wood 9. 134.1.1.3 Kiln seasoned selected class of sheesham wood 9. 134.1.2 With ISI marked stainless steel butt hinges of required size 9. 134.1.2.1 Second class teak wood 9. 134.1.2.2 Kiln seasoned and chemically treated hollock wood 9. 134.1.2.3 Kiln seasoned selected class of sheesham wood 9. 134.2 9.134.2.1 30 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size
sqm
2,814.50
166
Code No.
Description 9. 134.2.1.2 Kiln seasoned and chemically treated hollock wood 9. 134.2.1.3 Kiln seasoned selected class of sheesham wood 9. 134.2.2 With ISI marked stainless steel butt hinges of required size 9. 134.2.2.1 Second class teak wood 9.134.2.2.2 Kiln seasoned and chemically treated hollock wood 9.134.2.2.3 Kiln seasoned selected class of sheesham wood
9.135
Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. 9.135.1 With 2nd class teak wood beading 62X19 mm 9.135.2 With 12 mm mild steel U beading sqm sqm 1,433.75 1,160.30
9.136
Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately). Providing and fixing glazing in fire resistant door shutters, fixed panels, ventilators and partitions etc., with G.I. beading of appropriate size, made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant, including applying a coat of approved fire resistant primer on G.I. beading etc., complete all as per direction of Engineer-in-charge. 9.138.1 With clear fire resistant glass panes 6mm thick of approved brand, having minimum 60 minutes fire resistance
metre
1,161.45
9.137
sqm
5,727.20
9.138
sqm
25,435.15
9.139
Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately). 9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type
nos.
5,873.25
9.140
sqm
861.05
167
Description Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm ( 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge. 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm ( 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge. 9.142.1 Non decorative finish (matt finish) 9.142.2 Decorative finish (wood grained finish)
Unit
Rate
metre
544.50
9.142
sqm sqm
2,579.65 3,100.00
9.143
Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections , of size 65 mm x 55 mm with wall thickness 2.0 mm ( 0.2 mm) , corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge. Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge.
metre
389.60
9.144
sqm
2,703.40
168
Description Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm ( 0.2 mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness ( 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineerin-charge. Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm ( 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm ( 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm ( 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer's specification and direction of engineer-in-charge. Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. 9.147.1 Casement Window (Outward/Inward opening) with hinge System
Unit
Rate
metre
400.05
9.146
sqm
2,790.50
9.147
9.147.1.1 Frame (50 mm x 50 mm) 9.147.1.2 Sash (Style and Rail) (62 mm x 34 mm) 9.147.1.3 Mullion (intermediate Section) (66 mm x 50 mm) 9.147.1.4 'T' Profile (one vertical length in between two shutters) (24 mm x 34.5 mm) 9.147.1.5 Glazing bead (12 mm x 18 mm) 9.147.2 Casement Window (With friction hinge & outward opening) 9.147.2.1 Casement Frame (67 mm x 62 mm) 9.147.2.2 Casement Window Sash / Mullion (67 mm x 75 mm ) (style, rail and intermediate section) 9.147.2.3 Casement Glazing bead (35 mm x 18 mm)
SUBHEAD -9.0 WOOD AND PVC WORK
169
Code No.
Unit
Rate
9.147.3.1 Two Track Sliding Frame (67 mm x 52 mm) 9.147.3.2 Sliding window Sash (60 mm x 44 mm) 9.147.3.3 Sliding Interlock for Window (one vertical length in each shutter)( 45.5 mm x 28 mm) 9.147.3.4 Sliding Glazing bead (35 mm x 18 mm) 9.147.4 Sliding Door (Two Track, 2/4 Shutters) 9.147.4.1 Two Track Sliding Frame (67 mm x 52 mm) 9.147.4.2 Sliding Door Sash (80 mm x 44 mm) 9.147.4.3 Sliding Interlock for Door (one vertical length in each shutter) (45.5 mm x 28 mm) 9.147.4.4 Sliding Glazing bead (35 mm x 18 mm) 9.148 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge. 9.148.1 200 x 19 x 1.9 mm 9.148.2 250 x 19 x 1.9 mm 9.148.3 300 x 19 x 1.9 mm 9.148.4 350 x 19 x 1.9 mm 9.148.5 400 x 19 x 1.9 mm 9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete. Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete. Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete. Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.
kg
80.85
170
STEEL WORK
171
520.00 550.00 4,100.00 4,000.00 4,250.00 4,200.00 4,150.00 4,500.00 48.00 4,600.00
173
Code No. 1019 1020 1034 1035 1036 1143 1214 1215 1221 1222 1549 2205 2271 2406 2407 4006 4007 4008 4009 4010 4011 4012 4013 7029 7044 7045 7046 7047 7068 9999
Description Mild steel hooks Mild steel rivets Bolts and nuts up to 300 mm in length Bolts and nuts above 300 mm in length Iron pintels including welded pin Steel beading size 10 x 10 x 1.6 mm (box type) Welding by gas plant Welding by electric plant 20 mm dia holding down bolts Mild steel sheets with bolts and nuts to rest on pintels G.I. pipes 40 mm dia Carriage of Steel Carriage of G.I. pipes below 100 mm dia Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm). Float glass sheet of nominal thickness 5.5 mm (weight not less than 13.50 kg/sqm) Pressed steel door frames (mild steel sheet 1.60mm) Profile "B" Pressed steel door frames (mild steel sheet 1.60mm) Profile "C" Pressed steel door frames (mild steel sheet 1.60mm) Profile "E" Mild steel tubes hot finished welded type Mild steel tubes hot finished seamless type Mild steel tubes electric resistant or induction butt welded Circular C.I. Box for ceiling fan Pulley 40 mm dia Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm Rolling shutters of 80x0.90 mm laths Rolling shutters of 80x1.2 mm laths Top cover of Rolling shutters 0.90 mm thick Top cover of Rolling shutters 1.20 mm thick Extra for providing grilled rolling shutters with 8 mm dia M.S. rod Sundries
Unit each quintal quintal quintal each metre cm cm quintal each metre tonne tonne sqm sqm metre metre metre kilogram kilogram kilogram each each sqm sqm sqm metre metre sqm L.S.
Rate 30.00 4,800.00 5,400.00 5,400.00 35.00 20.00 1.50 1.50 5,400.00 110.00 202.00 77.87 77.87 310.00 450.00 220.00 240.00 270.00 48.00 58.00 65.00 50.00 25.00 230.00 930.00 1,010.00 270.00 305.00 225.00 1.49
174
Code No.
Unit
Rate
2506
Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave, Size 10 mm x 60 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave, Size 10 mm x 80 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave, Size 10 mm x 120 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave, Size 10 mm x 140 mm Carben Steel galvanised dash fastner (min 5 micron) of 10 mm dia double threaded 6.8 grade counter sunk head screw comprising of 10 mm dia polyamide PA 6 grade sleave, Size 10 mm x 160 mm Stainless steel (Grade-304) hollow section round / square tubes Stainless steel bolts / square bar and plates Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50 mm dia wire
10 nos
250.00
2507
10 nos
293.00
2508
10 nos
364.00
2509
10 nos
425.00
2510
10 nos kg kg sqm
175
kg
59.90
10.2
kg
66.50
10.3
sqm
4,234.25
10.4
sqm
2,996.40
10.5
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 10.6.1 10.6.2 10.6.3 80x1.25 mm M.S. laths with 1.25 mm thick top cover 80x1.20 mm M.S. laths with 1.20 mm thick top cover 80x0.90 mm M.S. laths with 0.90 mm thick top cover sqm sqm sqm each 1,840.85 1,583.40 1,476.90 429.85
10.7 10.8
Providing and fixing ball bearing for rolling shutters. Extra for providing mechanical device chain and crank operation for operating rolling shutters. 10.8.1 10.8.2 Exceeding 10.00 sqm and upto 16.80 sqm in the area Exceeding 16.80 sqm in area
sqm sqm
627.35 662.20
176
Description Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). Fixing standard steel glazed doors, windows and ventilators in walls, including fixing of float glass panes with glazing clips and special metalsash putty of approved make, or metal beading with screws, (only steel windows, glass panes cut to size and glazing clips or metal beading with screws, shall be supplied by department free of cost. 10.10.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 10.10.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
Unit
Rate
sqm
261.35
10.10
kg kg
27.55 15.00
10.11
Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 10.11.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 10.11.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
kg kg
96.30 68.75
10.12
Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units. Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 10.13.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 10.13.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
metre
29.25
10.13
kg kg
73.30 70.40
10.14
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-
177
Code No.
Description plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: 10.14.1 Profile B
Unit
Rate
10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb 10.14.1.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 10.14.2 Profile C
metre metre
346.75 339.85
10.14.2.1 Fixing with adjustable lugs with split end tail to each jamb 10.14.2.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 10.14.3 Profile E
metre metre
370.00 363.10
10.14.3.1 Fixing with adjustable lugs with split end tail to each jamb 10.14.3.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 10.15 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 10.15.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 10.15.2 Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 10.16 Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes 10.16.2 Hot finished seamless type tubes 10.16.3 Electric resistance or induction butt welded tubes 10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
metre metre
404.85 397.90
kg kg
121.45 114.30
kg kg kg
each
106.30
10.18
each
117.45
178
Description Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. Providing and fixing bolts including nuts and washers complete. Providing and fixing M.S. rivets of sizes in position. Welding by gas or electric plant including transportation of plant at site etc. complete. Item Shifted to Sub head 14 as item 14.73. Item Shifted to Sub head 14 as item 14.74. Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
Unit
Rate
kg kg kg cm
kg kg
67.20 77.90
10.26
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 10.26.1 M.S. tube 10.26.2 E.R.W. tubes 10.26.3 G.I. pipes kg kg kg 86.45 109.95 93.30
NEW ITEMS 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10.27.1 10 x 60 mm 10.27.2 10 x 80 mm 10.27.3 10 x 120 mm 10.27.4 10 x 140 mm 10.27.5 10 x 160 mm 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). each each each each each 54.95 59.90 74.20 81.30 103.00
kg
558.00
179
Description Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. 10.29.1 Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides 10.29.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides
Unit
Rate
sqm sqm
458.95 1,134.50
10.30
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 10.30.1 4.0 mm thick glass panes 10.30.2 5.5 mm thick glass panes sqm sqm 657.75 836.65
180
FLOORING
181
183
Code No. 0983 1007 1008 1149 1164 1165 1168 1187 1190 1194 1201 1202 1203 1215 1227 1228 1229 1231 2201 2202 2203 2204 2205 2209 2211 2216 2261 2268 2500 2602
Description Fine sand (zone IV) Structural steel such as tees, angles channels and R.S. joists Flats up to 10 mm in thickness Glass strip 4 mm thick 40 mm deep Red sand stone slab 40 mm thick (un-dressed) White sand stone slab 40 mm thick (un-dressed) Kota stone slab 20 mm to 25 mm thick (semi-polished) First class teak wood in scantling Second class teak wood in planks Second class deodar wood in planks Precast terrazzo tiles 22 mm thick (light shade) Precast terrazzo tiles 22 mm thick(medium shade) Precast terrazzo tiles 22 mm thick (dark shade) Welding by electric plant Chequered terrazzo tiles 22 mm thick(light shade) Chequered terrazzo tiles 22 mm thick(medium shade) Chequered terrazzo tiles 22 mm thick (dark shade) Extra for selected planks of second class teakwood Carriage of Bricks Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Timber Carriage of Steel Carriage of Cement Carriage of Tar bitumen Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of Fine sand (1 part badarpur sand : 2 parts jamuna sand) Carriage of Marble dust and marble chips Extra for selected planks of second class deodar wood Common burnt clay F.P.S. (non modular) bricks class designation 7.5
Unit cum quintal quintal metre sqm sqm sqm 10 cudm 10 cudm 10 cudm sqm sqm sqm cm sqm sqm sqm 10 cudm 1000 nos cum cum cum tonne tonne tonne tonne cum cum 10 cudm 1000 nos
Rate 640.00 4,250.00 4,200.00 9.00 155.00 170.00 270.00 700.00 720.00 480.00 240.00 220.00 200.00 1.50 300.00 260.00 225.00 115.00 233.60 87.60 87.60 100.11 77.87 77.87 87.60 77.87 87.60 87.60 73.00 2,900.00
184
Code No. 2710 2751 6001 6007 6010 6019 7024 7070 7071 7077 7236 7237 7254 7388 7800 7801 7802 7803 7804 7850 8620 8621 8622 8623
Description
Unit
Rate
White marble makrana second quality plain veined stone pieces for crazy flooring 8 mm thick marble tiles (polished) Raj Nagar White marble slab Makrana second quality plain veined 18 mm thick Pink marble slab plain 18 mm thick Udaypur green marble slab plain 18 mm thick Black Zebra marble slab plain 18 mm thick Acid Proof cement Chequered precast cement concrete tiles 22 mm thick using marble chips of size 6 mm - light shade using white cement White marble Raj Nagar plain 18 mm thick upto 0.50 sqm area Acid and alkali resistant tiles 300x300 mm size, 10 mm thick Precast chequered cement tiles 22 mm thick Dark shade using ordinary cement Precast chequered cement tiles 22 mm thick medium shade using 50% white cement, 50% ordinary cement Hardening compound Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt Ceramic Glazed Tiles Ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green, black Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades and designs of White, Ivory, grey, Fume Red brown etc. Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades designs except White, Ivory, Grey, Fume Red Brown etc Rectified - Ceramic Glazed Tiles Ist quality 300 x 300 mm or more in all shades designs White, Ivory, Grey, Fume Red Brown etc Rectified - Ceramic Glazed Tiles Ist quality 300 x 300 mm or more in all shades designs except White, Ivory, Grey, Fume Red Brown etc Agaria White marble slab plain 18 mm thick Vitrified floor tile 50x50 cm Vitrified floor tile 60x60 cm Vitrified floor tile 80x80 cm Vitrified floor tile 100x100 cm
quintal sqm sqm sqm sqm sqm tonne sqm sqm 10 nos sqm sqm litre each sqm sqm sqm sqm sqm sqm sqm sqm sqm sqm
130.00 340.00 1,850.00 610.00 660.00 470.00 8,100.00 470.00 545.00 520.00 230.00 360.00 37.00 48.00 295.00 360.00 367.00 510.00 535.00 1,090.00 735.00 865.00 1,070.00 1,630.00
185
Description High polymer modified quickset tile adhesive Sundries NEW CODES
Truf Paver (500 x 500 x 40 mm) Ceremic Tiles Pieces for Crazy Flooring Epoxy Grout
sqm quintal Kg
186
11.0 FLOORING
Code No. 11.1 Description Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 11.1.1 11.1.2 11.2 1:4 (1 cement : 4 coarse sand) 1:6 (1cement : 6 coarse sand) sqm sqm 489.20 455.90 Unit Rate
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate
sqm
339.55
11.3
sqm
280.05
11.4
52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufactures specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 11.6.1 18 mm thick
sqm
420.50
11.5
sqm
464.80
11.6
sqm
258.20
11.7
Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc. TERRAZO FLOORING 40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in
cum sqm
5,269.10 24.10
11.8
11.9
187
Code No.
Description proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement slurry etc. complete : 11.9.1 11.9.2 11.9.3 11.9.4 11.9.5 11.9.6 Dark shade pigment with ordinary cement Light shade pigment with white cement Medium shade pigment with 50% white cement and 50% ordinary cement White cement without any pigment Light shade pigment with ordinary cement Ordinary cement without any pigment
Unit
Rate
11.10
40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 31 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 9 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 4 mm to 7 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder : 7 marble chips) by volume, including cement slurry etc. complete. 11.10.1 Dark shade pigment with Ordinary cement 11.10.2 Light shade pigment with white cement 11.10.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.10.4 White cement without any pigment 11.10.5 Light shade pigment with ordinary cement 11.10.6 Ordinary cement without any pigment sqm sqm sqm sqm sqm sqm 478.45 532.50 504.30 503.25 485.50 451.60
11.11
40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 28 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 12 mm thick with white, black, chocolate, grey yellow or green marble chips of sizes from 7 mm to 10 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 2:3 (2 cement marble powder mix : 3 marble chips) by volume, including cement slurry etc. complete : 11.11.1 Dark shade pigment with ordinary cement 11.11.2 Light shade pigment with white cement 11.11.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.11.4 White cement without any pigment 11.11.5 Light shade pigment with ordinary cement 11.11.6 Ordinary cement without any pigment sqm sqm sqm sqm sqm sqm 501.65 577.40 537.85 530.40 511.55 464.55
11.12
Marble chips skirting up to 30 cm height, rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from smallest to 4 mm
188
Code No.
Description nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume : 11.12.1 18 mm thick with under layer 12 mm thick in cement plaster 1:3 (1 cement : 3 coarse sand) :
Unit
Rate
11.12.1.1 Dark shade pigment with ordinary cement 11.12.1.2 Light shade pigment with white cement 11.12.1.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.12.1.4 White cement without any pigment 11.12.1.5 Light shade pigment with ordinary cement 11.12.1.6 Ordinary cement without any pigment 11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 11.13.1 40 mm wide and 4 mm thick 11.14 11.15 Extra for laying terrazo flooring on staircase treads not exceeding 30 cm in width, including cost of forming, nosing etc. Crazy marble stone flooring, including filling the gaps with light shade pigment with white cement marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1 mm to 4 mm nominal size by volume), with under layer 25 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and cement slurry etc. complete : 11.15.1 18 mm thick crazy marble stone white, black or as specified TILE FLOORING 11.16 Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : 11.16.1 Light shade pigment using white cement 11.16.2 Medium shade pigment using 50%white cement and 50% ordinary cement 11.16.3 Dark shade pigment using ordinary cement 11.16.4 Ordinary cement without any pigment 11.17 11.18 Extra if terrazo tiles are laid in treads of steps not exceeding 30 cm in width. Precast terrazo tiles 22 mm thick with graded marble chips of sizes upto 12 mm, in skirting and risers of steps not exceeding 30 cm in height, on 12 mm thick cement plaster 1:3 (1 cement : 3 coarse sand),
metre sqm
29.40 26.75
sqm
773.45
189
Code No.
Description jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of : 11.18.1 Light shade pigment using white cement 11.18.2 Medium shades pigment using 50% white cement and 50% ordinary cement 11.18.3 Dark shade pigment using ordinary cement 11.18.4 Ordinary cement without any pigment
Unit
Rate
11.19
Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : 11.19.1 Light shade pigment using white cement 11.19.2 Medium shade pigment using 50% white cement, 50% ordinary cement 11.19.3 Dark shade pigment using ordinary cement 11.19.4 Ordinary cement without any pigment sqm sqm sqm sqm 846.00 773.40 709.00 671.30
11.20
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). 11.20.1 Light shade pigment using white cement 11.20.2 Medium shade pigment using 50% white cement 50% Grey cement 11.20.3 Dark shade pigment using ordinary cement 11.20.4 Ordinary cement without any pigment sqm sqm sqm sqm 953.20 789.55 602.15 564.35
11.21
Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. 11.21.1 In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) sqm 1,075.60 In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) sqm 1,129.95
11.21.2.1 Acid and alkali resistant tile 11.22 Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. 11.22.1 Marble tiles (polished) Raj Nagar 11.22.1.1 8 mm thick STONE FLOORING 11.23 Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick
sqm
748.15
190
Code No.
Description base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : 11.23.1 Makrana white second quality 11.23.2 Raj Nagar plain 11.23.3 Agaria White 11.23.4 Black Zebra 11.23.5 Udaipur green marble 11.23.6 Pink plain marble
Unit
Rate
11.24 11.25
Extra for pre finished nosing to treads of steps of marble stone. Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre . KOTA STONE FLOORING Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick
11.26
sqm
945.70
11.27
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. SAND STONE FLOORING 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 ( 1cement : 5 coarse sand) with joints finished flush. 11.28.1 Red sand stone 11.28.2 White sand stone
sqm
954.10
11.28
sqm sqm
462.20 481.40
11.29
40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. 11.29.1 Red sand stone 11.29.2 White sand stone sqm sqm 538.30 557.50
11.30
40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement :5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. 11.30.1 Red sand stone 11.30.2 White sand stone sqm sqm metre 591.40 610.55 52.45
11.31
Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.
191
Description Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre . WOODEN FLOORING 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : 11.33.1 Second class teak wood 11.33.2 Second class deodar wood
Unit
Rate
sqm
12.10
11.33
sqm sqm
3,049.05 2,045.60
11.34
38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete. Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete. CERAMIC GLAZED TILES Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete. Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete. Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except
sqm
5,455.30
11.35
kg
77.50
11.36
sqm
724.25
11.37
sqm
764.55
11.38
sqm
772.90
11.39
sqm
931.50
11.40
192
Code No.
Description White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete. VITRIFIED FLOOR TILES
Unit
Rate
sqm
961.25
11.41
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 11.41.1 Size of Tile 500x500 mm 11.41.2 Size of Tile 600x600 mm 11.41.3 Size of Tile 800x800 mm 11.41.4 Size of Tile 1000x1000 mm sqm sqm sqm sqm sqm 1,182.35 1,337.10 1,579.40 2,246.10 360.15
11.42 11.43
Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles. Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement , all complete as per direction of Engineer-in-charge. Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge. Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. 11.46.1 Size of Tile 500x500 mm 11.46.2 Size of Tile 600x600 mm 11.46.3 Size of Tile 800x800 mm 11.46.4 Size of Tile 1000x1000 mm
sqm
336.75
sqm
347.25
11.45
sqm
1,651.20
11.46
193
Description Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 11.47.1 Size of Tile 500x500 mm 11.47.2 Size of Tile 600x600 mm 11.47.3 Size of Tile 800x800 mm 11.47.4 Size of Tile 1000x1000 mm
Unit
Rate
11.48
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 11.48.1 Size of Tile 500x500 mm 11.48.2 Size of Tile 600x600 mm 11.48.3 Size of Tile 800x800 mm 11.48.4 Size of Tile 1000x1000 mm sqm sqm sqm sqm 194.25 164.10 133.95 98.00
11.49
Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622 , of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 11.49.1 Size of Tile 500x500 mm 11.49.2 Size of Tile 600x600 mm 11.49.3 Size of Tile 800x800 mm 11.49.4 Size of Tile 1000x1000 mm sqm sqm sqm sqm sqm 1,302.95 1,457.70 1,701.75 2,368.45 7.15
11.50
Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.
194
ROOFING
195
197
Description
Unit
Rate
Non-Asbestos fibre ( high impact poly propelene reinforced ) cement eaves filler piece Non-Asbestos fibre ( high impact poly propelene reinforced ) cement north light curves Non-Asbestos fibre ( high impact poly propelene reinforced ) cement ventilator curves Non-Asbestos fibre ( high impact poly propelene reinforced ) cement barge boards 6 mm thick Non-Asbestos fibre ( high impact poly propelene reinforced ) cement ridge finial Non-Asbestos fibre ( high impact poly propelene reinforced ) cement special north light curves Non-Asbestos fibre ( high impact poly propelene reinforced ) cement S type louvers Non-Asbestos multi purpose fibre ( high impact poly propelene reinforced ) cement board 6 mm thick Stone Aggregate (single size), 20 mm nominal size Stone Aggregate (single size), 10 mm nominal size Bhusa Paving bitumen of grade VG-10 of approved quality Bitumen hot sealing compound, grade A White face insulating board, 12 mm thick Natural colour insulating board, 12 mm thick Flame retardant face inslulating board, 12 mm thick Flat pressed 3 layer particle board (medium density) Grade 1, 12 mm thick Portland Cement White cement Coal (steam) Brass screws 25 mm Bright finished or black enameled mild steel screws 40 mm
each
150.00
0230
metre
310.00
0231
each
390.00
0232
metre
395.00
0233
pair
140.00
0234
each
514.00
0235
each
250.00
0236
198
Code No. 0765 0771 0811 0845 0865 0869 0870 0875 0886
Description
Unit
Rate
Hessian cloth Kerosene oil Mud (dry) Roofing paint for iron sheets in red colour Pig lead Plaster of Paris Plug Red, chocolate, orange, buff or yellow (red oxide of iron) light shade Standard holder bat clamps for sand cast iron or cast iron pipes 150mm dia Sand Cast iron plain shoe 150 mm dia Coarse sand (zone III) Galvanised steel plain sheets Standard quality hard board sheet 3 mm thick Standard quality hard board sheet 4.5 mm thick Spun yarn Flats up to 10 mm in thickness Mild steel expanded metal 20x60 mm strands Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots Galvanised steel J or L hooks 8 mm dia Galvanised steel bolts & nuts 10 mm dia and 125 mm long round head with slots Mild stel bolts 6 mm dia and 25 mm long with hexagonal head Galvanised steel bolts & nuts 10 mm dia and 27 cm long both sides threaded with 4 galvanised steel nuts Galvanised steel bolts 10 mm dia and 7 cm long with nuts Red sand stone slab 45 mm to 50 mm thick (un-dressed)
10 nos 10 nos
20.00 90.00
1023 1024
each 10 nos
10.00 25.00
1025 1031
1032 1174
199
Code No. 1175 1190 1196 1207 1208 1209 1210 1211 1213 1219 1220 1331 1984 2202 2203 2204 2205 2207 2209 2211 2216 2273 2302 2308 3002 3004 3050 4009
Description
Unit
Rate
White sand stone slab 45 mm to 50 mm thick (un-dressed) Second class teak wood in planks First class kail wood in planks G.I. Limpet washer Bitumen washer G.I. plain washer thick G.I. plain washer thin G.I. plain washer for seam bolts Water proofing materials Wire nails Wire mesh (rabbit) M.S.Holder bat clamp of approved design for 100 mm S.C.I. pipe Common burnt clay F.P.S. bricks tile class designation 10 Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Timber Carriage of Steel Carriage of Brick tiles Carriage of Cement Carriage of Tar bitumen Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of A.C.sheet and accessories Carriage of G.I.sheet and accessories Carriage of Plaster of paris Polyvinyl chloride sheet 400 micron thick Stone ware spouts 100 mm dia 60 cm long Galvanised steel corrugated sheets Mild steel tubes hot finished welded type
sqm 10 cudm 10 cudm 100 nos 100 nos 100 nos 100 nos 100 nos kilogram kilogram sqm each 1,000 nos cum cum cum tonne 1,000 nos tonne tonne tonne tonne tonne tonne sqm each quintal kilogram
185.00 720.00 300.00 35.00 25.00 32.00 30.00 32.00 25.00 52.00 45.00 17.00 3,100.00 87.60 87.60 100.11 77.87 140.16 77.87 87.60 77.87 77.87 77.87 77.87 31.00 33.00 5,075.00 48.00
200
Code No. 4202 7009 7010 7011 7012 7013 7014 7015 7016 7017 7018 7019 7020 7021 7090 7091 7187 7188 7189 7190 7191 7192 7193 7194 7195 7196 7197
Description Red oxide Zinc chromate primer 12.5 mm thick tapered edge gypsum plain borad Galvanised Steel celling section (size 80x26x0.50 mm) Galvanised Steel perimetre Channel (Size 20x27x30x0.50 mm) Galvanised Steel intermediate Channel (Size 15x45x15x0.90 mm) Galvanised Steel angle hanger (Celling angle) (Size 25x10x0.50 mm) Galvanised Steel connecting clips (2.64 mm dia and 230 mm long GI wire) Galvanised Steel soffit cleat (Size 27x37x25x0.60 mm) Joint filler Joint finisher Joint tape roll Dash fastener / Chemical Fastener All drive screws ( for gypsum board) Primer ( for gypsum board) Expanded polystyrene type N- Normal Expanded polystyrene type - SE C.I. grating 150 mm dia, Weighing not less than 440 gm uPVC pipes (working pressure 4 kg / cm 2 ) Single socketed pipe 75 mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Single socketed pipe 110 mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Rubber (Seal) Ring 75mm dia uPVC pipes (working pressure 4 kg / cm 2 ) Rubber (Seal) Ring 110 mm dia uPVC coupler for uPVC drainage pipes 75 mm uPVC coupler for uPVC drainage pipes 110 mm uPVC pushfit coupler (single) 75 mm thick uPVC pushfit coupler (single) 110 mm thick uPVC single equal Tee (without door) 75x75x75 mm uPVC single equal Tee (without door) 110x110x110 mm
Unit litre sqm metre metre metre metre each each kilogram kilogram roll each 100 nos litre sqm sqm each metre metre each each each each each each each each
Rate 68.00 160.00 39.00 27.00 42.00 19.00 6.20 4.00 22.00 24.00 140.00 13.00 56.00 85.00 130.00 155.00 22.00 67.00 129.00 16.00 20.00 34.00 52.00 50.00 81.00 95.00 128.00
201
Code No. 7198 7199 7208 7209 7212 7213 7214 7215 7231 7232 7266 7267 7268 7385 7386 7388 7857 7904 8611 8612 8613 8614 8615 8616 8617 8618 8667 8668 8669 8670
Description uPVC single equal Tee (with door) 75x75x75 mm uPVC single equal Tee (with door) 110x110x110 mm uPVC bend 87.50 75 mm bend uPVC bend 87.50 110 mm bend uPVC plain shoe 75 mm bend uPVC plain shoe 110 mm bend uPVC pipe clip 75 mm bend uPVC pipe clip 110 mm bend Resin Bonded Glass wool 16 kg/m 50 mm thick Resin Bonded Glass wool 24 kg/m 50 mm thick Pressed clay tiles 20 mm thick 250 x 250 mm size Plain ceiling tiles (BWP type phenol formaldehyde synthetic resin bonded) (600x600x12 mm) Semi perforated ceiling tiles (600x600x12 mm) 3 mm thick translucent white acrylic plastic sheet 12 mm thick particle board ceiling tile Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt P.T.M.T. Grating square slit 150 mm Machine moulded common burnt clay tile bricks of class designation 12.5 Main T ceiling sections 24x38x0.3 mm (3 metre long) Perimeter wall angle 24 x 24 x 0.3 mm (3 metre long) Intermediate cross T-Section 24x25x0.3 mm (1.2 m long) Intermediate cross T-Section 24x25x0.3 mm (0.6 m long) Hanger rod 4 mm thick Adjustment clip 85x30x0.8 mm Soffit cleat (Size 27x37x25x1.60 mm) Dash fastener 6 mm dia 50 mm long UV stabilised 2 mm thick plain FRP sheet UV stabilised 2 mm thick corrugated FRP sheet Mangalore ridge tiles 20 mm thick Mangalore tiles 20 mm thick
Unit each each each each each each each each sqm sqm 1,000 nos each each sqm sqm each each 1,000 nos each each each each each each each each sqm sqm each each
Rate 115.00 180.00 56.00 95.00 107.00 207.00 16.00 31.00 145.00 204.00 12,150.00 120.00 120.00 570.00 260.00 48.00 77.00 3,700.00 187.00 118.00 72.00 34.00 7.00 6.00 3.00 11.00 465.00 538.00 29.00 10.20
202
Code No. 8671 8672 8673 8674 8675 8676 8677 9999
Description Precoated galvanised iron profile sheet 0.50 mm TCT Precoated galvanised steel plain ridges Precoated galvanised steel flashings/aprons Precoated galvanised steel gutter Precoated galvanised steel north light curves Precoated galvanised steel barge board Precoated galvanised steel crimp curve Sundries NEW CODES
1204 7028 7030 7031 7050 7051 7052 7053 8589 8590 8591 8592 8593 8594 8595 8597 8598 8599
Precast heat resistant terrace tiles (size 300x300 mm) and 20 mm thick 12.5 mm thick Fully Perforated gypsum board 12.5 mm thick tapered edge gypsum fire resistant board 12.5 mm thick tapered edge gypsum moisture resistant board PU Primer 40 mm (average) PU spray having 40-45 kg/m3 density GI wire netting 3/4" x 24 G 400 G polythene sheet Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm thick Galvanised Steel main Tee ceiling section Size 24x38x0.33 mm (3 metre long) Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm (3.00 metre long) Galvanised Steel intermediate cross T section Size 24 x 25 x 0.33 mm (1.2 metre long) Galvanised Steel intermediate cross T section Size 24 x 25 x 0.33 mm (0.6 metre long) Galvanised Steel soffit cleat size 25x35x1.60 mm Wooden screws with plastic rawl plugs 35x8 mm GI Metal Tile Clip in Plain Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick GI Metal Tile Clip in Perforated Beveled edge global white colour tiles of size 600x600 mm and 0.5 mm thick GI Metal Tile Lay-in Plain Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick
sqm sqm sqm sqm sqm sqm sqm sqm sqm each each each each each each sqm sqm sqm
482.00 927.00 237.00 271.00 40.75 419.40 26.25 15.00 858.00 192.00 125.00 77.00 39.00 3.00 0.55 894.00 998.00 809.00
203
Description GI Metal Tile Lay-in Perforated Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm and 12.5 mm thick Gypsum Tiles Fully Perforated Square edge of Size 595x595 mm and 12.5 mm thick Spring T-section 24x34x0.45 mm (3.00 meter long) C Wall angle section 20x30x20x0.50 mm (3.00 meter long) Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long) Spring T-connector C Carrier Connector C Suspension Clip Wire Coupling Clip
Unit
Rate
sqm
906.00
8601
sqm
468.00
8602
204
12.0 ROOFING
Code No. 12.1 Description Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.1 12.1.2 12.1.3 12.2 1.00 mm thick with zinc coating not less than 275 gm/m 0.80 mm thick with zinc coating not less than 275 gm/m 0.63 mm thick with zinc coating not less than 275 gm/ m sqm sqm sqm 878.45 742.80 627.25 Unit Rate
Extra for straight cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter for chimney stacks, sky light etc. : 12.2.1 12.2.2 12.2.3 1.00 mm thick 0.80 mm thick 0.63 mm thick metre metre metre 31.80 25.45 25.45
12.3
Extra for circular cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter : 12.3.1 12.3.2 12.3.3 1.00 mm thick 0.80 mm thick 0.63 mm thick metre metre metre 183.95 146.95 146.95
12.4
Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 12.4.1 12.4.2 0.80 mm thick with zinc coating not less than 275 gm/m 0.63 mm thick with zinc coating not less than 275 gm/m metre metre 470.10 411.40
12.5
Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete : 12.5.1 1.60 mm thick with zinc coating not less than 350 gm/m metre 893.95 Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts, G.I. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1cement : 3 coarse sand). 12.6.1 1.00 mm thick with zinc coating not less than 275 gm/m metre 350.10 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 12.7.1 12.7.2 0.80 mm thick with zinc coating not less than 275 gm/m 0.63 mm thick with zinc coating not less than 275 gm/m metre metre 439.05 390.15
12.6
12.7
205
Code No.
Unit
Rate
12.8
Providing non-asbestos high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required. Extra for straight cutting in non- asbestos polypropylene reinforced cement corrugated, semi-corrugated 6 mm thick sheet roofing for making openings of area exceeding 40 square decimeter for chimney stacks, skylights etc. Extra for circular cutting in non-asbestos polypropylene reinforced cement corrugated/semi-corrugated 6 mm thick sheet roofing for making openings of area exceeding 40 square decimeter. Extra for providing and fixing wind ties of 40x 6 mm flat iron section. Providing and fixing ridges and hips in non-asbestos fibre cement high impact polypropylene reinforced roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete. 12.12.1 12.12.2 12.12.3 12.12.4 Corrugated serrated adjustable ridges Plain wing adjustable ridges Close fitting adjustable ridges Unserrated adjustable hips
sqm
375.75
12.9
metre
25.45
12.10
metre metre
70.35 109.30
12.11 12.12
NON AC ACCESSORIES 12.13 Providing and fixing non-asbestos fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete: 12.13.1 12.13.2 12.13.3 12.13.4 12.13.5 12.13.6 12.13.7 12.13.8 12.14 Corrugated apron pieces Eave's filler pieces North light curves Ventilator curves Barge boards Ridge finials Special north light curves S type louvers metre metre metre metre metre pair each metre 288.30 198.95 424.35 522.50 517.35 189.40 671.35 287.30
Providing flat iron brackets 50x3 mm size with necessary bolts, nuts and washers etc. for fixing asbestos cement / G.S. sheets gutters with purlins. Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : 12.15.1 With residual type petroleum bitumen of grade VG - 10
metre
46.40
12.15
sqm
105.50
206
Description 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat : 12.16.1 With common burnt clay F.P.S.(non modular) brick tile of class designation 10
Unit
Rate
sqm
375.60
12.17
10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar with bhusha @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow-dung) and covered with machine moulded tile bricks, grouted with cement mortar 1:3 ( 1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat. 12.17.1 With machine moulded common burnt clay F.P.S. (non modular) brick tiles of class designation 12.5, conforming to IS 2690
sqm sqm
402.10 8.65
12.18 12.19
Extra for every additional 1 cm thickness of mud phaska. Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat : 12.19.1 With common burnt clay F.P.S. (non modular) brick tiles of class designation 10
sqm
283.65
12.20
Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete. Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1 In 75x75 mm deep chase
sqm
431.90
12.21
metre
109.05
12.22
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : 12.23.1 Red sand stone slab
each
148.75
12.23
207
Code No.
Description 12.23.1.1 12.23.2 12.23.2.1 CEILING 40 to 50 mm thick White sand stone slab 40 to 50 mm thick
12.24
Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) : 12.24.1 12.24.1.1 12.24.2 12.24.2.1 12.24.3 12.24.3.1 Natural colour insulating board 12 mm thick White face insulating board 12 mm thick Flame retardant face insulating board 12 mm thick sqm 565.70 sqm 623.20 sqm 508.20
12.25
Providing and fixing flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) : 12.25.1 12 mm thick sqm 578.00 Providing and fixing plain Multipurpose Cement board ( High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) : 12.26.1 6 mm thick cement board 2nd class teak wood planks 20 mm thick Natural colour insulating board 12 mm thick White face insulating board: 12 mm thick Flame retardant face insulating board: 12 mm thick Standard quality hard board sheet: 3 mm thick 4.5 mm thick metre metre sqm 140.20 143.40 124.05 metre 172.90 metre 180.05 metre 165.75 sqm metre 395.30 345.65 Extra for Circular cutting including wastages in ceiling with: 12.27.1 12.27.2 12.27.2.1 12.27.3 12.27.3.1 12.27.4 12.27.4.1 12.27.5 12.27.5.1 12.27.5.2
12.26
12.27
12.28 12.29
Extra for providing and fixing ceiling to curved surfaces in narrow widths Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminium primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodised aluminium (with 15 micron anodic coating) T-sections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to
208
Code No.
Description main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminium frame work shall be paid separately).
Unit
Rate
sqm
588.70
12.30
Extra for providing 3 mm thick translucent white acrylic plastic sheets of approved quality in false ceiling instead of 12 mm thick plain or design particle board ceiling tiles. Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) : 12.31.1 12.31.2 Flat surfaces Curved surfaces
sqm
360.05
12.31
Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling. Extra for providing plaster of Paris (Gypsum anhydrous) ceiling above 5metres height from floor level. Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building. Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183. Density 16 kg/m3 , 50 mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by criss-crossing GI wire. Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in-charge : 12.36.1 12.36.2 With Type N - Normal 50 mm thick With Type SE - Self Extinguishing type 50 mm thick
sqm
431.70
12.35
sqm.
226.10
12.36
sqm sqm
200.90 232.85
RAIN WATER SPOUT AND PIPE 12.37 Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand). 12.37.1 12.38. Stone ware spout each 68.10 Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 12.38.1 12.38.2
SUBHEAD -12.0 ROOFING
each each
112.50 121.80
209
Description Providing lead caulked joints to sand cast iron rain water pipes and fittings : 12.39.1 12.39.2 100 mm dia Pipe 150 mm dia Pipe
Unit
Rate
each each
207.85 287.10
12.40
Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately) : 12.40.1 12.40.1.1 Sand cast iron plain shoes : 150 mm diameter each 407.85
12.41
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.1 12.41.2 75 mm diameter 110 mm diameter metre metre 124.90 206.90
12.42
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 12.42.1.1 12.42.1.2 12.42.2 12.42.2.1 12.42.2.2 12.42.3 12.42.3.1 12.42.3.2 12.42.4 12.42.4.1 12.42.4.2 12.42.5 12.42.5.1 12.42.5.2 12.42.6 12.42.6.1 12.42.6.2 Coupler 75 mm 110 mm Single pushfit Coupler 75 mm 110 mm Single tee with door 75x75x75 mm 110x110x110 mm Single tee without door 75x75x75 mm 110x110x110 mm Bend 87.5 75 mm bend 110 mm bend Shoe (Plain) 75 mm Shoe 110 mm Shoe each each 163.80 287.05 each each 104.55 156.95 each each 184.70 241.65 each each 207.95 302.05 each each 116.15 163.95 each each 97.60 130.25
12.43
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length,
210
Code No.
Description including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 12.43.1 12.43.2 75 mm 110 mm
Unit
Rate
12.44 12.45
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.45.1 12.45.2 12.45.3 12.45.4 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I 12.5 mm thick tapered edge gypsum moisture resistant board Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60
sqm
1,626.80
211
Description Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms. Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 12.47.1 12.47.2 2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified 2mm thick flat
Unit
Rate
each
96.65
12.47
sqm sqm
932.50 822.05
12.48
Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately). Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.51.1 12.51.2 12.51.3 12.51.4 12.51.5 12.51.6 Ridges plain (500 - 600mm) Flashings/ Aprons.( Upto 600 mm) North light curves Barge board (Upto 300 mm) Crimp curve Gutter .(600 mm over all girth)
sqm
249.65
12.49
sqm
127.00
12.50
sqm
601.75
12.51
212
Description Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I , of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48
Unit
Rate
sqm
1,425.90
12.52.2
sqm
1,538.60
12.52.3
sqm
1,029.60
12.52.4
213
Code No.
Description mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.
Unit
Rate
sqm
1,048.20
NEW ITEMS 12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/cosmos / Hexa or equivalent of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main 'T' , bottom exposed with 24 mm of all T-sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/m 0 KC. 12.54 Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and
sqm
1,566.00
214
Code No.
Description spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring 'T' with : 12.54.1 GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.
Unit
Rate
sqm
1,559.45
12.54.2
sqm
1,680.30
12.55
Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/ cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-in-Charge. Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge.
sqm
1,033.70
12.56
sqm
1,077.15
12.57
sqm
304.95
215
FINISHING
217
219
Code No. 0833 0834 0835 0850 0851 0855 0856 0857 0858 0859 0868 0869 0982 0999 1000 1179 1198 1213 1216 2202 2203 2209 2911 4201 4202 4203 4204 4205 4206 4207
Description Synthetic enamel paint in black or chocolate shade Synthetic enamel paint in all shades except black or chocolate shade Plastic emulsion paint White lead Water proofing cement paint Wax polish (ready made) Ordinary varnish Superior copal varnish Superior spar varnish Oil type wood preservative Premixed super white gypsum plaster. Plaster of Paris Coarse sand (zone III) Shellac Spirit Crushed stone 2.36 mm to 12.5 mm size Second class kail wood in planks Water proofing materials Whiting Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Cement Stone chippings/ screenings 10/ 11.2 mm nominal size Aluminium primer Red oxide Zinc chromate primer Copper acetate Hydrochloric acid Copper chloride Copper nitrate Ammonium chloride
Unit litre litre litre kilogram kilogram kilogram litre litre litre litre kilogram kilogram cum kilogram litre cum 10 cudm kilogram quintal cum cum tonne cum litre litre kilogram kilogram kilogram kilogram kilogram
Rate 130.00 135.00 165.00 80.00 40.00 175.00 65.00 125.00 125.00 70.00 7.00 4.00 1,120.00 205.00 65.00 915.00 250.00 25.00 400.00 87.60 87.60 77.87 1,050.00 72.00 68.00 270.00 32.00 272.00 200.00 15.00
220
Code No. 7239 7240 7306 8504 8505 8506 8507 8509 8510 8733 9999
Description Epoxy paint Fire retardant paint Aluminium T or L sections Multi surface paint Acrylic exterior paint Premium Acrylic exterior paint Textured exterior paint Special Primer (C.W.) Metal Primer (U.G.) Synthetic ployster triangular fibre of length 6mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 Sundries NEW CODES
Unit litre litre kilogram litre litre litre litre litre litre kg L.S.
Rate 315.00 350.00 220.00 272.00 130.00 230.00 198.00 83.00 107.00 365.00 1.49
Silicon and acrylic emulsion Acrylic distemper 1st quality, having VOC content less than 50 gm/litre Acrylic emulsion , having VOC content less than 50 gm/litre Premium acrylic emulsion of interior grade, having VOC content less than 50 gm/litre Synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 gm/litre Ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 gms/litre Ready mixed red oxide zinc chromatic on steel/ iron work, having VOC content less than 250 gms/litre Water thinnable cement primer for interior wall surface, having VOC content less than 50 gms/litre
221
13.0 FINISHING
Code No. Description Note :- Rates for external plaster are for height upto 10m from ground level unless otherwise stated. CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 13.1.1 13.1.2 13.2 1:4 (1 cement: 4 fine sand) 1:6 (1 cement: 6 fine sand) sqm sqm 123.50 112.50 Unit Rate
15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 13.2.2 1:4 (1 cement: 4 fine sand) 1:6 (1 cement: 6 fine sand) 1:4 (1 cement: 4 fine sand) 1:6 (1 cement: 6 fine sand) sqm sqm sqm sqm 143.35 130.20 173.30 156.15
13.3
CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster of mix : 13.4.1 13.4.2 13.5 13.5.1 13.5.2 13.6 13.6.1 13.6.2 1:4 (1 cement: 4 coarse sand) 1:6 (1 cement: 6 coarse sand) 1:4 (1 cement: 4 coarse sand) 1:6 (1 cement: 6 coarse sand) 1:4 (1 cement: 4 coarse sand) 1:6 (1 cement: 6 coarse sand) sqm sqm sqm sqm sqm sqm 132.10 121.05 153.60 140.45 186.70 169.50
CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 13.7 12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.1 13.7.2 13.8 1:3 (1 cement: 3 fine sand) 1:4 (1 cement: 4 fine sand) sqm sqm 164.50 153.45
15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 13.8.1 13.8.2 1:3 (1 cement: 3 fine sand) 1:4 (1 cement: 4 fine sand) sqm sqm 186.50 173.30
13.9
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 13.9.1 13.9.2 12 mm cement plaster 20 mm cement plaster sqm sqm 173.10 233.80
13.10
15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.
sqm
196.75
222
Code No.
Unit
Rate
13.11
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. 12 mm cement plaster 1:2 (1 cement : 2 stone dust). 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall. 20 mm cement plaster 1:2 (1 cement : 2 stone dust). 6 MM CEMENT PLASTER 6 mm cement plaster of mix : 13.16.1 1:3 (1 cement : 3 fine sand)
sqm
182.90
13.12
sqm
101.00
6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. Neat cement punning. ROUGH CAST PLASTER Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. 13.19.1 Ordinary cement finish using ordinary cement
sqm sqm
136.25 31.10
13.18 13.19
sqm
315.30
PEBBLE DASH PLASTER 13.20 Pebble dash plaster upto 10 m height above ground level with a mixture of washed pebble or crushed stone 6 mm to 12.5 mm nominal size, dashed over and including fresh plaster in two layers under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
sqm Per bag of 50 kg cement used in the mix sqm sqm sqm
300.15
13.21
13.22 13.23
Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. Extra for plastering on circular work not exceeding 6 m in radius: 13.23.1 13.23.2 In one coat In two coats
223
Description Extra for plastering done on moulding, cornices or architraves including neat finish to line and level : 13.24.1 13.24.2 In one coat In two coats Spherical ceiling Groined ceiling Flewing soffits
Unit
Rate
13.25
13.26
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ARTIFICIAL STONE PLASTER Extra for lining out plaster to imitate stone or concrete blocks walling. PLAIN CEMENT MORTAR BANDS 12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) : 13.28.1 13.28.2 13.28.3 13.28.4 Flush Band Sunk Band Raised Band Moulded Band
13.27 13.28
13.29
18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): 13.29.1 13.29.2 13.29.3 13.29.4 Flush Band Sunk Band Raised Band Moulded Band cm per metre cm per metre cm per metre cm per metre 2.90 3.15 3.55 6.35
13.30
18 mm thick moulded cement mortar band in two coats under layer 12 mm thick with cement mortar 1:5 (1 cement : 5 coarse sand) top layer 6 mm thick with cement mortar 1:4 (1 cement : 4 fine sand). POINTING OF BRICK WORK Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand) : 13.31.1 13.31.2 Flush / Ruled/ Struck or weathered pointing Raised and cut pointing
cm per metre
6.40
13.31
sqm sqm
78.35 126.90
POINTING ON TILE BRICK WORK 13.32 Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand) : 13.32.1 13.33 Flush/ Ruled/ Struck or weathered pointing sqm 107.35 POINTING ON STONE WORK Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : 13.33.1 13.33.2 Flush/ Ruled pointing Raised and cut pointing sqm sqm 111.80 201.85
224
Description Raised and cut pointing on stone work in white cement mortar 1:3 (1 white cement : 3 marble dust). Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 fine sand) : 13.35.1 Flush/ Ruled pointing
Unit
Rate
sqm
219.30
sqm sqm
63.75 4.65
13.36
Extra for pointing on walls on the outside at height more than 10 m from ground level for every additional height of 3 m or part there of. INTERIOR FINISHING
13.37
White washing with lime to give an even shade : 13.37.1 New work (three or more coats) sqm sqm 11.75 4.75
13.38 13.39
Satna lime wash on walls with one coat. Colour washing such as green, blue or buff to give an even shade : 13.39.1 13.39.2 New work (two or more coats) with a base coat of white washing with lime New work (two or more coats) with a base coat of whiting
sqm sqm
16.15 15.85
13.40
Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade. Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer
sqm
46.30
13.41
sqm
66.70
13.42
Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. 13.42.1 Two or more coats on new work sqm 37.35
13.43
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1 Water thinnable cement primer sqm 27.55
EXTERIOR FINISHING 13.44 Finishing walls with water proofing cement paint of required shade : 13.44.1 13.45 New work (Two or more coats applied @ 3.84 kg/10 sqm) sqm 44.95
Finishing walls with textured exterior paint of required shade : 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
sqm
117.70
13.46
Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
sqm
67.50
225
Description Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : 13.47.1 New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
Unit
Rate
sqm
80.45
13.48
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand and manufacture Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
sqm
78.75
13.48.2
sqm
67.70
13.48.3
sqm
70.40
13.49 13.50
Deleted Applying priming coat : 13.50.1 13.50.2 13.50.3 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) sqm sqm 25.85 24.70
sqm
20.70
13.50.4
sqm
11.40
13.51
Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : 13.51.1 13.51.2 One coat Two coats sqm sqm 48.95 77.85
13.52
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. 13.52.1 13.52.2 On steel work On concrete work sqm sqm 105.50 108.55
13.53
Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.53.1 New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution sqm 59.35
226
Description Applying a coat of mordant solution on G.S. sheet : 13.54.1 13.54.2 With a solution of 38 gms of copper acetate in a litre of soft water With a solution made of 13 gms of hydrochloric acid in a solution of 13 gms each of copper chloride, copper nitrate and ammonium chloride dissolved in a litre of soft water
Unit
Rate
sqm
20.15
sqm
19.95
13.55
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture, over and including a priming of ready mixed zinc chromate yellow primer on new work : 13.55.1 13.55.2 100 mm diameter pipes 150 mm diameter pipes metre metre 25.60 38.20
13.56
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 13.56.1 13.56.2 100 mm diameter pipes 150 mm diameter pipes metre metre 28.90 43.10
13.57
Painting with oil type wood preservative of approved brand and manufacture : 13.57.1 New work (two or more coats) sqm 18.70 Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant. Coal tarring two coats on new work using 0.16 Litre and 0.12 litre coal tar per sqm in the first coat and second coat respectively. Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 13.60.1 Two or more coats on new work sqm 60.25 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1 Two or more coats on new work sqm 53.85 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
13.58
sqm sqm
267.15 24.55
13.59 13.60
13.61
13.62
sqm
78.80
13.63
Painting with aluminium paint of approved brand and manufacture to give an even shade . 13.63.1 Two or more coats on new work sqm 47.70 Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade : 13.64.1 Two or more coats on new work sqm 50.50
13.64
227
Description Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 13.65.1 Two or more coats on new work
Unit
Rate
sqm
44.55
13.66
Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade : 13.66.1 Two or more coats on new work Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish Two or more coats glue sizing with spar varnish or an under coat of flatting varnish Two or more coats on new works including a coat of wood filler sqm 57.00 Varnishing with varnish of approved brand and manufacture : 13.67.1 13.67.2 sqm sqm 80.60 81.60
13.67
13.68
13.69
Polishing on wood work with ready mixed wax polish of approved brand and manufacture : 13.69.1 New work sqm sqm per letter per cm height 60.50 28.50 Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture. Lettering with black Japan paint of approved brand and manufacture
13.70 13.71
1.70
13.72
Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (payment for providing grooves shall be made separately). Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 13.73.1 13.73.2 15 mm wide and 15 mm deep groove 20 mm wide and 15 mm deep groove
sqm
417.35
13.73
metre metre
23.65 24.10
13.74
Extra for washed grit plaster on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. Extra for washed stone grit plaster on circular work not exceeding 6 m in radius (in two coats).
sqm sqm
65.85 41.15
13.75
228
Description Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineerin-Charge. Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster. Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete. Extra for addition of synthetic Polyester triangular fibre of length 6 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement plaster/mortar by using 125 gms. of synthetic Polyester triangular fibre for 50 Kgs. cement used in cement mortar as per directions of Engineer-in-Charge.
Unit
Rate
metre sqm
72.15 81.30
13.77 13.78
sqm
214.40
13.79
53.00
NEW ITEMS 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 13.81.1 13.81.2 13.82 One coat Two coats sqm sqm 21.25 34.40
sqm
76.05
13.81
Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 13.82.1 13.82.2 One coat Two coats sqm Sqm 37.65 56.60
13.83
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 13.83.1 13.83.2 One coat Two coats sqm Sqm 40.75 61.45
229
Description Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 13.84.1 13.84.2 One coat Two coats
Unit
Rate
sqm Sqm
35.70 53.90
13.85
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ litre With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
sqm
27.40
13.85.2
sqm sqm
24.30 25.55
13.85.3
230
REPAIRS TO BUILDING
231
233
Code No. 0419 0420 0421 0422 0423 0427 0428 0429 0430 0442 0444 0445 0446 0449 0450 0452 0524 0525 0526 0527 0528 0585 0586 0587 0589 0595 0597 0608 0637 0639 0640
Description Brass hard drawn hooks and eyes 250 mm Brass hard drawn hooks and eyes 200 mm Brass hard drawn hooks and eyes 150 mm Brass hard drawn hooks and eyes 100 mm Brass casement window fastener Brass quadrant stays 300 mm Brass fanlight catch Brass fanlight pivot Brass chain with hook for fan light catch Brass helical spring 150 mm Brass curtain rod 20 mm dia 1.25 mm thick Brass curtain rod 25 mm dia 1.25 mm thick Brass brackets (curtain rods) 20 mm Brass screws 50 mm Brass screws 40 mm Brass screws 25 mm Chromium plated Brass butt hinges (heavy) type 75x65x 4 mm (200gms) Chromium plated Brass butt hinges (light/ordinary) type 125x 70x4 mm Chromium plated Brass butt hinges (light/ordinary) type 100x 70x4 mm Chromium plated Brass butt hinges (light/ordinary) type 75x 40x2.5 mm Chromium plated Brass butt hinges (light/ordinary) type 50x40x2.5 mm Chromium plated Brass screws 50 mm Chromium plated Brass screws 40 mm Chromium plated Brass screws 30 mm Chromium plated Brass screws 20 mm Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm Bright finished or black enameled mild steel butt hinges 50x37x1.50 mm Nickel plated bright finished mild steel piano hinges 1 mm thick 25 mm wide Bright finished or black enameled mild steel screws 40 mm Bright finished or black enameled mild steel screws 25 mm Bright finished or black enameled mild steel screws 20 mm
Unit 10 nos 10 nos 10 nos 10 nos each each 10 nos 10 nos each each metre metre each 100 nos 100 nos 100 nos 10 nos 10 nos 10 nos 10 nos 10 nos 100 nos 100 nos 100 nos 100 nos 10 nos 10 nos metre 100 nos 100 nos 100 nos
Rate 675.00 625.00 600.00 500.00 45.00 120.00 170.00 190.00 30.00 300.00 100.00 120.00 40.00 200.00 160.00 95.00 950.00 810.00 675.00 425.00 185.00 230.00 190.00 150.00 100.00 80.00 45.00 35.00 50.00 30.00 25.00
234
Code No. 0761 0771 0775 0811 0815 0816 0826 0827 0828 0829 0833 0835 0845 0851 0855 0856 0857 0858 0859 0863 0982 0999 1000 1003 1007 1008 1023 1034 1174 1186 1188 1189 1190 1194 1196 1199
Description Fuel wood Kerosene oil Dehradun white lime Mud (dry) Dry distemper Oil bound washable distemper/ Acrylic distemper Aluminium paint Acid proof paint (chocolate or black) Anticorrosive bituminous paint (black) Black Japan Synthetic enamel paint in black or chocolate shade Plastic emulsion paint Roofing paint for iron sheets in red colour Water proofing cement paint Wax polish (ready made) Ordinary varnish Superior copal varnish Superior spar varnish Oil type wood preservative Putty for wood work Coarse sand (zone III) Shellac Spirit Mild steel round bar above 12 mm dia Structural steel such as tees, angles channels and R.S. joists Flats up to 10 mm in thickness Galvanised steel J or L hooks 8 mm dia Bolts and nuts up to 300 mm in length Red sand stone slab 45 mm to 50 mm thick (un-dressed) Superior class teak wood such as Dandeli, Balarshah or Malabar in planks First class teak wood in planks Second class teak wood in scantling Second class teak wood in planks Second class deodar wood in planks First class kail wood in planks Sal wood in scantling
Unit quintal litre quintal cum kilogram kilogram litre litre litre litre litre litre litre kilogram kilogram litre litre litre litre kilogram cum kilogram litre quintal quintal quintal 10 nos quintal sqm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm 10 cudm
Rate 450.00 30.00 410.00 50.00 35.00 42.00 115.00 105.00 85.00 90.00 130.00 165.00 110.00 40.00 175.00 65.00 125.00 125.00 70.00 30.00 1,120.00 205.00 65.00 4,000.00 4,250.00 4,200.00 90.00 5,400.00 165.00 1,050.00 800.00 640.00 720.00 480.00 300.00 500.00
235
Code No. 1208 1209 1213 1215 1314 1315 2201 2202 2203 2204 2205 2209 2216 2264 2406 2407 2466 2467 2602 4009 4202 7019 7241 7340 7346 7387 7397 7398 7399 7442 8505 8506 8507 8508 9999
Description Bitumen washer G.I. plain washer thick Water proofing materials Welding by electric plant C.P.brass chain with 32 mm dia rubber plug C.P.brass chain with 40 mm dia rubber plug Carriage of Bricks Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Timber Carriage of Steel Carriage of Cement Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of Rubbish Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm) Float glass sheet of nominal thickness 5.5 mm (weight not less than 13.50 kg/sqm) Hollock wood in scantling Chromium plated Brass pull bolt lock (locking bolt) of size 85 mmx 42 mm with screws, bolts, nuts and washers complete Common burnt clay F.P.S. (non modular) bricks class designation 7.5 Mild steel tubes hot finished welded type Red oxide Zinc chromate primer Dash fastener/Chemical Fastener Melamine polish Stainless steel pin Double coupler Spigot for standard Jointing Base Jack Challies (M.S. tube) Cup locks Wheel 75 mm dia 40 mm wide Acrylic exterior paint Premium Acrylic exterior paint Textured exterior paint Primer for cement paint Sundries
Unit 100 nos 100 nos kilogram cm each each 1000 nos cum cum cum tonne tonne tonne cum sqm sqm 10 cudm each 1,000 nos kilogram litre each litre kg each Kilogram each each each each litre litre litre litre L.S.
Rate 25.00 32.00 25.00 1.50 26.00 27.00 233.60 87.60 87.60 100.11 77.87 77.87 77.87 87.60 310.00 450.00 310.00 145.00 2,900.00 48.00 68.00 13.00 250.00 180.00 55.00 45.00 180.00 800.00 75.00 60.00 130.00 230.00 198.00 63.00 1.49
236
Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead : 14.2.1 14.2.2 14.2.3 Door chowkhats Window chowkhats Clerestory window chowkhats each each each 600.10 367.05 267.90
14.3
Fixing chowkhat in existing opening in brick / RCC wall with dash fasteners/ Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener. Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground. 14.4.1 For door/ window/ clerestory window
each
131.55
14.4
sqm
366.65
14.5
Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: 14.5.1 14.5.2 Float glass panes of thickness 4 mm Float glass panes of thickness 5.5 mm Float glass panes of thickness 4 mm Float glass panes of thickness 5.5 mm Float glass panes of thickness 4 mm Float glass panes of thickness 5.5 mm 2nd class teak wood fillets Hollock wood fillets sqm sqm sqm sqm sqm sqm metre metre metre 585.20 764.10 724.65 903.50 610.80 789.65 29.85 24.35 17.25
14.6
Renewing glass panes, with wooden fillets wherever necessary: 14.6.1 14.6.2
14.7
Renewing glass panes and refixing existing wooden fillets: 14.7.1 14.7.2
14.8
Supplying and fixing new wooden fillets wherever necessary: 14.8.1 14.8.2
14.9
237
Description Refixing old glass panes with putty and nails Fixing old glass panes with wooden fillets (excluding cost of fillets) Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete. Regrading terracing of mud phaska covered with tiles or brick, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) within 50 metres lead. Replacing sand stone slabs in roofing, laid in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary repairs and cement pointing with same mortar complete, including disposal of rubbish to dumping ground within 50 metres of lead : 14.14.1 Red/ white sand stone slabs 30 to 50 mm thick
each
190.10
14.13
sqm
206.30
14.14
sqm
459.10
14.15
Renewing wooden battens in roofs, including making good the holes in wall and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground within 50 metres lead : 14.15.1 Sal wood battens cum 63,053.20
14.16
Renewing wooden beams in roofs including making good the holes in walls and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground within 50 metres lead : 14.16.1 14.16.1.1 14.16.1.2 14.16.2 14.16.2.1 14.16.2.2 Not exceeding 4.00 metres in length. Sal wood beams Hollock wood beams Above 4.00 metres and upto 5.00 metres length. Sal wood beams Hollock wood beams cum cum 65,676.30 42,912.50 cum cum 64,870.70 42,131.00
14.17
Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground within 50 metres lead. Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska : 14.18.1 14.18.2 With F.P.S. brick tiles With modular brick tiles
sqm
19.85
14.18
sqm sqm
42.65 43.55
238
Description Taking out wind ties from roof including cutting out rusted bolts, nuts etc. and removing materials to any distance within compound and stacking. Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand. Renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer. Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. complete. 14.22.1 14.22.2 Wheel 50 mm dia and below Wheel above 50 mm dia
Unit
Rate
kg
1.45
14.20
metre
55.45
14.21
kg
120.25
14.22
111.15 170.45
EARTH WORK 14.23 14.24 14.25 Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. Mud mortar made with local clay good earth. BRICK WORK Brick work with common burnt clay bricks of class designation 7.5 in mud mortar WOOD WORK 14.26 Providing and fixing 25 mm thick shutters for cup board etc. : 14.26.1 14.26.1.1 14.26.1.2 14.26.2 14.26.2.1 14.26.2.2 14.27 Panelled or panelled & glazed shutters : Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws. Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws. Glazed shutters : Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws. Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws. sqm sqm 3,193.30 2,615.20 sqm sqm 3,069.85 2,532.10 cum 2,583.60 kilo litre cum 72.55 301.10
Providing and fixing plain jaffri door and window shutters including bright or/and black enamelled M.S. butt hinges with necessary screws 35x10 mm laths placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm beading complete with : 14.27.1 Second class teak wood sqm 2,714.20 Providing and fixing curtain rods of 1.25 mm thick brass plates with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 14.28.1 14.28.2 20 mm diameter. 25 mm diameter. metre metre 187.45 210.65
14.28
239
Description Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows. Providing joists (karries) including hoisting, fixing in position and applying wood preservative on unexposed surface etc. complete with : 14.30.1 14.30.2 Sal wood Hollock wood
Unit
Rate
kg
62.00
14.30
cum cum
62,391.40 39,881.50
14.31
Providing and fixing bright finished brass single acting spring hinges with necessary brass screws etc. complete : 14.31.1 14.31.2 14.31.3 150 mm 125 mm 100 mm each each each 387.40 329.30 209.45
14.32
Providing and fixing bright finished brass double acting spring hinges with necessary brass screws etc. complete : 14.32.1 14.32.2 14.32.3 150 mm 125 mm 100 mm each each each 619.70 445.45 383.65
14.33
Providing and fixing bright finished brass flush bolts with necessary brass screws etc. complete : 14.33.1 14.33.2 14.33.3 250 mm 150 mm 100 mm each each each 176.85 152.40 111.75
14.34
Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete Providing and fixing bright finished brass hard drawn hooks and eyes : 14.35.1 14.35.2 14.35.3 14.35.4 14.35.5 300 mm 250 mm 200 mm 150 mm 100 mm
each
197.30
14.35
Providing and fixing bright finished brass fan light pivot with necessary brass screws etc. complete. Providing and fixing 300 mm long bright finished brass chain with hook for fan light including necessary brass screws etc. complete. Providing and fixing bright finished brass quadrant stay 300 mm long with necessary brass screws etc. complete. Providing and fixing bright finished brass helical door spring (superior quality).
240
Description Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 14.40.1 14.40.2 14.40.3 14.40.4 14.40.5 125x70x4 mm (ordinary type) 100x70x4 mm (ordinary type) 75x65x4 mm (heavy type) 75x40x2.5 mm (ordinary type) 50x40x2.5 mm (ordinary type)
Unit
Rate
14.41
Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete. FINISHING White washing with lime to give an even shade : 14.42.1 14.42.2 Old work (two or more coats) Old work (one or more coats)
each
177.45
14.42
sqm sqm
7.05 4.35
14.43
Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade. Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 14.45.1 Old work (one or more coats)
sqm
5.70
14.44
sqm
21.25
14.45
sqm
23.40
14.46
Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.47.1 Old work (one or more coats)
sqm
7.50
14.47
sqm
30.30
14.48
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture over and including a priming coat of ready mixed zinc chromate yellow primer on new work : 14.48.1 75 mm diameter pipes metre 19.10 Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture on old work : 14.49.1 14.49.2 14.49.3 75 mm diameter pipes 100 mm diameter pipes 150 mm diameter pipes metre metre metre 9.30 12.20 17.40
14.49
14.50
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with aluminium paint of approved brand and
241
Code No.
Description manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work : 14.50.1 14.50.2 14.50.3 75 mm diameter pipes 100 mm diameter pipes 150 mm diameter pipes
Unit
Rate
14.51
Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work : 14.51.1 14.51.2 14.51.3 75 mm diameter pipes 100 mm diameter pipes 150 mm diameter pipes metre metre metre 9.75 12.55 17.85
14.52
Painting with oil type wood preservative of approved brand and manufacture : 14.52.1 Old work (one or more coats) sqm 14.25
14.53
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 14.53.1 One or more coats on old work sqm 39.30
14.54
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.54.1 One or more coats on old work sqm 35.20
14.55
Painting with aluminium paint of approved brand and manufacture to give an even shade : 14.55.1 One or more coats on old work sqm 30.75
14.56
Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade : 14.56.1 One or more coats on old work sqm 33.15
14.57
Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 14.57.1 One or more coats on old work sqm 29.80
14.58
French spirit polishing : 14.58.1 One or more coats on old work sqm 69.80
14.59
Polishing on wood work with ready made wax polish of approved brand and manufacture : 14.59.1 Old work sqm Per letter per cm height sqm 30.80
14.60
1.10 31.95
14.61
Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.
242
Description Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin : 14.62.1 14.62.2 32 mm dia 40 mm dia
Unit
Rate
each each
44.15 45.30
14.63
Distempering with 1st quality acrylic washable distemper (ready made) of approved manufacturer and of required shade and colour complete. as per manufacturer's specification. 14.63.1 One or more coats on old work sqm 21.35
14.64
Finishing walls with water proofing cement paint of required shade : 14.64.1 Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. Old work (one or more coats @ 2.20 kg/10 sqm) complete.
sqm sqm
41.65 28.40
14.64.2 14.65
Finishing walls with textured exterior paint of required shade : 14.65.1 14.65.2 Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm. Old work (One or more coats) applied @ 1.82 ltr/10 sqm. sqm sqm 99.50 59.90
14.66
Finishing walls with Acrylic Smooth exterior paint of required shade : 14.66.1 14.66.2 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface Old work (One or more coat applied @ 0.90 ltr/10 sqm). sqm sqm 48.30 31.65
14.67
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade 14.67.1 14.67.2 Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface Old work (one or more coats applied @ 0.83 ltr/10 sqm). sqm sqm 62.20 40.30
14.68 14.69
Deleted. Varnishing with varnish of approved brand and manufacture: 14.69.1 14.69.2 One or more coats with copal varnish One or more coats with spar varnish sqm sqm sqm sqm 33.85 34.40 64.20 32.00
Melamine polishing on wood work (one or more coat). Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work. Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the
243
Code No.
Description required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.
Unit
Rate
sqm
127.10
14.73
Providing and fixing bright finished brass casement window fasteners or peg stays to windows/ ventilators with necessary welding and machine screws etc. complete. Providing and fixing 14 mm bright finished brass spring catch to steel centre hung ventilators with necessary welding and machine screws etc. complete.
kg
373.15
14.74
each
42.10
Note :- Item no. 14.73 & 14.74 are brought from Sub head 10 Steel work (Item no. 10.23 & 10.24).
244
245
247
cum
234.20
15.2
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge. Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in -charge. Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 15.7.1 15.7.2 15.7.3 15.7.4 In mud mortar In lime mortar with old mughal bricks In lime mortar In cement mortar
cum
978.95
15.4
cum
874.50
15.5
sqm kg
325.15 2.60
15.6 15.7
15.8
Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured) : 15.8.1 15.8.2 15.8.3 From brick work in mud mortar From brick work in lime mortar From brick work in cement mortar 1000 nos 1000 nos 1000 nos 1,277.55 1,474.15 1,841.60
15.9
Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : 15.9.1 15.9.2 In lime mortar In cement mortar cum cum 318.95 676.05
15.10
Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means
248
Code No.
Description including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : 15.10.1 15.10.2 In lime mortar In cement mortar
Unit
Rate
cum cum
403.50 790.80
15.11
Removing mortar from and cleaning stones and concrete articles (net quantity of stacks of cleaned materials will be measured) : 15.11.1 15.11.2 In lime mortar In cement mortar cum cum 131.50 189.55
15.12
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 15.12.1 15.12.2 Of area 3 sq. metres and below Of area beyond 3 sq. metres each each 101.70 139.85
15.13
Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : 15.13.1 15.13.2 Of area 3 sq. metres and below Of area beyond 3 sq. metres each each 39.70 52.45
15.14
Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : 15.14.1 15.14.2 Of sectional area 40 square centimetres and above Of sectional area below 40 square centimetres cum metre 1,231.15 4.90
15.15
Extra for dismantling trusses, rafters, purlins etc. of wood work for every additional span of one metre or part thereof beyond 10 metres : 15.15.1 15.15.2 Of sectional area 40 square centimetres and above Of sectional area below 40 square centimetres Cum per metre span Metre per metre span 172.65 0.50
15.16
Extra for dismantling trusses, rafters, purlins etc. of wood work for every additional height of one metre or part thereof beyond 5 metres : 15.16.1 15.16.2 Of sectional area 40 square centimetres and above Of sectional area below 40 square centimetres Cum per metre height Metre per metre height 245.90 0.95
15.17
Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: 15.17.1 15.17.2 R.S. Joists Channels, angles, tees and flats kg kg 0.95 0.65
15.18
Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50metres lead.
kg
1.55
249
Description Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge. Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional span of one metre or part thereof beyond 10 metres Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional height of one metre or part thereof beyond 5 metres. Extra for marking of structural steel work required to be re-erected. Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 15.23.1 15.23.2 For thickness of tiles 10 mm to 25 mm For thickness of tiles above 25 mm and up to 40 mm
Unit
Rate
1.05
15.20
sqm sqm
20.30 31.25
15.24
Demolishing dry brick pitching in floors, drains etc. including stacking serviceable material and disposal of unserviceable material within 50 metres lead : Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Demolishing mud phaska in terracing and disposal of material within 50 metres lead. Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of : 15.28.1 15.28.2 G.S. Sheet Asbestos sheet
cum
363.35
15.25
sqm
73.70
15.26
sqm cum
29.05 251.40
15.27 15.28
sqm sqm
45.70 21.60
15.29
Dismantling stone slab roofing over wooden karries or R.C.C. battens (dismantling karries and battens to be paid for separately), including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Dismantling jack arch roofing and floors including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Demolishing thatch roofing including mats, bamboo, jaffari etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. Dismantling wooden ballies in posts and struts including stacking within 50 metres lead.
cum
736.90
15.30
sqm
70.25
15.31
sqm
58.20
15.32
sqm metre
16.10 5.75
15.33
250
Description Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of : 15.34.1 15.34.2 T' or 'L' iron or pipe R.C.C.
Unit
Rate
each each
76.00 87.35
15.35
Cutting ballies or wooden posts of fencing at the point of projection above the concrete or ground and stacking the same within 50 metres lead. Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. Dismantling wooden trellis work excluding frames but including stacking the serviceable material within 50 metres lead. Dismantling expanded metal or I.R.C. fabrics with necessary battens and beading including stacking the serviceable material within 50 metres lead. Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : 15.39.1 15.39.2 15.39.3 Up to 10 mm thick Thickness above 10 mm up to 25 mm Thickness above 25 mm up to 40 mm
each kg sqm
sqm
21.10
15.39
15.40
Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 metres lead : 15.40.1 15.40.2 Thickness up to 40 mm Thickness above 40 mm up to 75 mm sqm sqm 80.40 120.35
15.41
Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 15.42.1 15.42.2 15.42.3 75 to 80 mm dia pipe 100 mm dia pipe 150 mm dia pipe
sqm
15.85
15.42
15.43
Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : 15.43.1 15.43.2 Water bound macadam road bituminous road sqm sqm 61.70 119.95
15.44
Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15.44.1 15.44.2 15 mm to 40 mm nominal bore Above 40 mm nominal bore metre metre 44.10 50.30
251
Description Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: 15.45.1 15.45.2 15.45.3 Up to 150 mm diameter Above 150 mm dia up to 300 mm dia Above 300 mm diameter
Unit
Rate
15.46
Dismantling steel cylinder R.C. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metres lead as per direction of Engineer-in-charge : 15.46.1 15.46.2 Up to 600 mm diameter Above 600 mm diameter metre metre 204.75 508.80
15.47
Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually/ by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-charge : 15.47.1 15.47.2 Up to 150 mm diameter Above 150 mm diameter metre metre 91.05 110.65
15.48
Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge. Taking out C.I. cover with frame from R.C.C. top slab of inspection chambers of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge. Dismantling of R.C.C. spun vent shaft including excavating the cement concrete pit completely, taking out the shaft, refilling the excavated gap, stacking the useful materials near the site and disposal of unserviceable materials within 50 metres lead. Dismantling of road gully chamber of various sizes including C.I. grating with frame including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead including refilling the excavated gap. Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 metres 15.53.1 15.53.2 Up to 150 mm diameter Above 150 mm diameter
each
198.25
15.49
each
116.50
15.50
each
1,298.15
15.51
each
269.70
15.52
each
261.90
15.53
each each
95.10 331.85
252
Description Dismantling of spindle fire hydrant including stacking of useful materials within 50 metres lead. Dismantling of cement concrete platform along with curtain walls and base concrete etc. including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead : 15.55.1 15.55.2 15.55.3 120 x 120 cm (outside to outside) 210 x 120 cm (outside to outside) 320 x 120 cm (outside to outside)
Unit
Rate
each
198.90
15.56
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars. Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of Engineer-in-charge. Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
sqm
15.00
15.57
sqm
15.90
15.58
cum
1,075.90
15.59
cum
166.70
cum
101.75
253
ROAD WORK
255
257
Code No. 0114 0115 0123 0124 0126 0128 0130 0131 0138 0139 0155 0157 0286 0287 0291 0292 0293 0294 0295 0296 0297 0298 0304 0309 0310 0312 0313 0314 0317 0364 0365
Description Beldar Coolie Mason (brick layer ) 1st class Mason (brick layer ) 2nd class Mason (for ornamental stone work) 1st class Mate Mistry Painter Sprayer (for bitumen, tar etc.) Skilled Beldar (for floor rubbing etc.) Mason (average) Operator (Pile/Special machine ) Brick Aggregate (single size ) : 50 mm nominal size Brick Aggregate (single size) : 40 mm nominal size Stone Aggregate (single size ) : 63 mm nominal size Stone Aggregate (single size) : 50 mm nominal size Stone Aggregate (single size) : 40 mm nominal size Stone Aggregate (single size) : 25 mm nominal size Stone Aggregate (single size) : 20 mm nominal size Stone Aggregate (single size) : 12.5 mm nominal size Stone Aggregate (single size) : 10 mm nominal size Stone Aggregate (single size) : 06 mm nominal size Bajri Paving bitumen of grade VG-10 of approved quality Bitumen emulsion Bitumen grade PMB - 40 Blown type petroleum bitumen of penetration 85 / 25 of approved quality Bitumen hot sealing compound : grade A premoulded joint filler 12 mm thick Wire brush Soft brush
Unit day day day day day day day day day day day day cum cum cum cum cum cum cum cum cum cum cum tonne tonne tonne tonne kilogram sqm each each
Rate 247.00 247.00 301.00 273.00 301.00 260.00 301.00 273.00 260.00 260.00 287.00 327.00 490.00 500.00 850.00 900.00 950.00 1,000.00 1,050.00 1,050.00 1,050.00 1,100.00 900.00 37,000.00 28,500.00 41,400.00 37,000.00 26.00 350.00 20.00 18.00
258
Code No. 0367 0370 0588 0777 0784 0810 0979 0982 0983 1007 1008 1013 1021 1028 1029 1030 1151 1158 1159 1179 1235 1241 1980 2200 2201 2202 2203 2205 2206 2208 2209 2211
Description Portland Cement Coal (steam) Chromium plated Brass screws 25 mm Dry hydrated lime (factory made) Marble dust/ powder Moorum Royalty for good earth Coarse sand (zone III) Fine sand (zone IV) Structural steel such as tees, angles channels and R.S. joists Flats up to 10 mm in thickness Mild steel sheets for tanks Hard drawn steel wire fabric Straining bolts Galvanised steel barbed wire Galvanised steel turn buckles Boundary stone top chisel dressed 15x15x90 cm Stone for pitching 15 cm x 22.5 cm Stone dust Crushed stone 2.36 mm to 12.5 mm size Diesel oil Commercial LPG in cylinder Fly ash Carriage of Steam coal Carriage of Bricks Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Steel Carriage of Stone aggregate 40 mm nominal size and above Carriage of Lime Carriage of Cement Carriage of Tar bitumen
Unit tonne quintal 100 nos quintal cum cum cum cum cum quintal quintal quintal sqm each quintal each each cum cum cum litre kg cum tonne 1,000 nos cum cum tonne cum cum tonne tonne
Rate 5,000.00 400.00 115.00 220.00 1,000.00 450.00 30.00 1,120.00 640.00 4,250.00 4,200.00 4,600.00 430.00 70.00 5,175.00 15.00 60.00 420.00 925.00 915.00 41.29 51.00 7.75 100.11 233.60 87.60 87.60 77.87 95.22 87.60 77.87 87.60
259
Code No. 2215 2216 2241 2260 2261 2265 2267 2302 2311 2314 2335 2342 2602 2704 2901 2902 2903 2904 2908 2909 2910 2911 2914 2916 5001 6501 7254 7255 7256 7309 7318
Description Carriage of Soling stone & masonry stone Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of Good earth Carriage of Brick aggregate Carriage of Fine sand (1 part badarpur sand : 2 parts jamuna sand) Carriage of Moorum Carriage of Stone dust Carriage of G.I.sheet and accessories Carriage of Red bajri Carriage of Barbed wire Carriage of Jamuna sand Carriage of Solvent/ Diesel Common burnt clay F.P.S. (non modular) bricks class designation 7.5 Aluminium Strip 40 mm wide and 2 mm thick Stone Aggregate (Single size) : 100 mm nominal size Stone Aggregate (Single size) : 80 mm nominal size Stone chippings/ screenings 4.75 mm nominal size Stone chippings/ screenings 150 micron nominal size Over burnt (Jhama) Brick Aggregate: 120 mm to 40 mm size Over burnt (Jhama) Brick Aggregate: 90 mm to 40 mm size Stone chippings/ screenings 12.5/ 13.2 mm nominal size Stone chippings/ screenings 10/ 11.2 mm nominal size Solvent Paving Asphalt VG -10 of approved quality Mobil oil Sand zone V (Jamuna) Hardening compound Road marking paint (spirit based) Superior quality road marking paint (water based) Paving Asphalt VG-30 of approved quality Plasticizer / super plasticizer
Unit cum tonne cum cum cum cum cum tonne cum tonne cum quintal 1,000 nos kilogram cum cum cum cum cum cum cum cum kilogram tonne litre cum litre litre litre tonne kilogram
Rate 103.06 77.87 109.50 95.22 87.60 87.60 87.60 77.87 87.60 77.87 87.60 8.76 2,900.00 210.00 750.00 750.00 1,150.00 1,150.00 330.00 360.00 1,050.00 1,050.00 23.00 37,500.00 186.00 500.00 37.00 120.00 170.00 38,500.00 36.50
260
Code No. 7382 7426 7739 7741 7742 8685 8686 8687 8688 8689 8690 8691 8692 8693 8694 8695 8696 8697 9999
Description Bitumen emulsion rapid setting (R.S.) confirming to IS : 8887 Cat's eye Modified Bitumen Refinery produced CRMB - 55 Modified Bitumen Refinery produced CRMB - 60 Bitumen emulsion medium setting (M.S.) confirming to IS : 8887 Delineator Precast C.C. Kerb stone M - 25 Thermoplastic paint Glass beads Interlocking C.C. paver block ( 60 mm thick, M-30 ) High intensity retro - reflective sheet Punched tape concertina coil 600 m dia 10m openable length (Total length 90m) RBT reinforced barbed wire Turn buckle and strengthening bolt Precast pavement slab 450 x 450 x 50 mm (M - 30) Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm, PVC coated to outer dia 5 mm Chain link fabric fencing mesh of size 25x25 mm made of G.I. wire of dia 3 mm Sundries NEW CODES
Unit tonne each tonne tonne tonne each cum kg kg sqm sqm bundle metre each set each sqm sqm sqm L.S.
Rate 27,700.00 180.00 38,500.00 38,800.00 28,200.00 310.00 4,025.00 63.00 62.00 325.00 1,525.00 730.00 8.50 40.00 55.00 258.00 285.00 340.00 1.49
Dozer D-80-A 12 Motor Grader 3.35 metre blade Hydraulic Excavator of 1 cum bucket Front end loader 1 cum bucket capacity (incl POL) Tipper -5 Cum Vibratory roller 8 to 10 tonne Smooth Wheeled Roller 8 to 10 tonne Tandem Road Roller Water Tanker 5 to 6 KL capacity
261
Code No. 0058 0059 0060 0061 0062 0063 0064 0065 0066 0068 0069 0070 0071 0075 0076 7280
Description Air compressor Wet Mix Plant 60 TPH Mechanical Broom Hydraulic Emulsion Pressure Distributor @ 1750 sqm per hour Hot mix Plant -120 TPH capacity Hot mix Plant 100 TPH Capacity Paver finisher Hydrostatic with sensor control 100 TPH Paver finisher Mechanical 100 TPH Batching and Mixing Plant @ 75 cum per hour Concrete Paver finisher with 40 HP Motor and sensor Generator 250 KVA Generator 100 KVA/125 KVA Truck 5.5 cum/ 10 tonnes Road sweeper (Mechamical Broom) @ 1250 sqm per hour Drum Type HMP of 60-90 TPH capacity @ 75 tonne per hour actual output Waste plastic additive
Unit hour hour hour hour hour hour hour hour hour hour hour hour tonne km hour hour tonne
Rate 325.00 1,200.00 360.00 800.00 23,700.00 17,500.00 2,700.00 1,000.00 2,500.00 2,900.00 900.00 700.00 3.00 360.00 14,000.00 40,000.00
262
sqm
61.25
16.2
cum
7.75
16.3
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . Laying water bound macadam sub-base with brick aggregate and blinding material, earth etc. including screening, sorting and spreading to template and consolidation with light power road-roller etc. complete.(payment for brick aggregate and moorum etc. to be made separately) 16.5.1 16.5.2 Over burnt (Jhama) brick aggregate 120 mm to 40 mm Over burnt (Jhama) brick aggregate 90 mm to 45 mm
cum
330.15
16.5
cum cum
246.35 246.35
16.6
Supplying, stacking and Spreading 6 mm thick red bajri, watering and rolling complete including preparation of the surface and rolling. 16.6.1 With road roller/ hand roller sqm 11.65 Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres. 16.7.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 metre 84.25
16.7
16.8
Brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres : 16.8.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 metre 23.80
263
Description Scarifying metalled (water-bound) road surface including disposal of rubbish, lead upto 50 m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity. Making bajri path including preparation of subgrade, supplying and laying brick aggregate of 50 mm nominal size 7.5 cm deep with blinding material consisting of 12 mm moorum and 12 mm red bajri consolidated with road roller. Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete. Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Unit
Rate
sqm
10.90
16.10
sqm sqm
105.20 336.50
16.11 16.12
sqm
292.40
16.13
Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required. 16.13.1 16.13.2 bituminous portion Water bound macadam cum cum sqm 1,861.60 989.25 92.40
16.14
Cutting bajri paths and making good the same including supply of extra quantities of brick aggregate, moorum and red bajri required. FENCING Supplying at site : 16.15.1 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-incharge (cost of earth works in excavation, concrete works in foundation to be paid separately). Welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Priming & Painting to be paid for separately).
16.15
cum
16,302.45
16.15.2
kg each set
64.55 135.15
16.16 16.17
Supplying and fixing turn buckles and straining bolts for barbed wire fencing. Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. 16.17.1 With G.I. barbed wire
metre
7.60
16.18
Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I.
264
Code No.
Description staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. 16.18.1 With G.I. barbed wire
Unit
Rate
metre
11.60
16.19
Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. Welded steel wire fabric fencing with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x 60 cm of mix 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size), every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50 cm of the same mix, provided with welded steel wire fabric fixed between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts, welded steel wire fabric, painting, earth work in excavation and concrete to be paid for separately). ROAD SIGNS Engraving letters in hard stone Providing and fixing 15x15x90 cm boundary stone of hard stone with top 30 cm chisel dressed on all four sides including top (cost of excavation, refilling and concrete etc. to be paid for separately). Providing and fixing 15 cm dia at top, 20 cm at bottom and 90 cm high precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) boundary stone as per standard design, including finishing smooth with cement mortar 1:3 (1 cement : 3 fine sand) (cost of excavation, refilling and concreting to be paid for separately). Providing and fixing precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) kilometre stone as per standard design, including finishing smooth in 1:3 cement mortar (1 cement : 3 fine sand) but excluding the cost of earth work, concrete in foundation, painting and lettering etc. which shall be paid for separately. 16.24.1 16.24.2 16.24.3 35x111x25 cm size 50x152.5x25 cm size 35x93.5x18 cm size
Kg.
62.10
16.20
20.65
16.21 16.22
3.00
each
111.30
16.23
each
380.55
16.24
SURFACE DRESSING 16.25 Surface dressing on new surface with paving bitumen of grade VG 10 of approved quality using 2.25 kg of bitumen per sqm with 1.65 cum of stone chippings 13.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity etc. complete: Surface dressing on new surface in two coats with bitumen of grade VG -10 of approved quality using 1.8 kg of bitumen per sqm with 1.5 cum of stone chippings 13.2 mm nominal size per 100 sqm of road surface for first coat and 1.1 kg. of bitumen per sqm with 1.00 cu. metre of stone chippings 11.2 mm nominal size per 100 sqm of road surface for second coat, including consolidation of each coat separately with road roller of 6 to 8 tonne capacity etc. complete.
sqm
145.80
16.26
sqm
197.35
265
Description Surface dressing on old surface with hot bitumen of grade VG - 10 of approved quality using 1.95 kg of bitumen per sqm with 1.50 cum of stone chippings 11.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity, etc. complete. Surface dressing one coat on new surface with bitumen of specified grade at a rate of 1.95 kg/sqm of surface area with 1.5 cum of stone chippings 13.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity , etc. complete : 16.28.1 Using bitumen emulsion (minimum 50% bitumen contentRS grade conforming to IS : 8887)
Unit
Rate
sqm
120.45
16.28
sqm
106.80
16.29
Surface dressing one coat on old surface with bitumen of specified grade at the rate of 1.22 kg/ sqm of surface area with 1.10 cum of stone chippings 11.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity etc. complete : 16.29.1 Using bitumen emulsion (minimum 50% bitumen contentRS grade conforming to IS : 8887) sqm 68.25
PREMIX CARPET 16.30 Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : 16.30.1 16.30.2 16.31 On W.B.M. @ 0.75 Kg / sqm On bituminous surface @ 0.50 Kg / sqm sqm sqm 40.15 29.00
Providing and applying tack coat using bitumen emulsion conforming to IS: 8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. 16.31.1 With rapid setting bitumen emulsion sqm sqm sqm sqm 14.25 9.40 14.50 9.55 16.31.1.1 On W.B.M / W.M.M. @ 0.4kg/sqm 16.31.1.2 On bituminous surface @ 0.25kg/sqm 16.31.2 With medium setting bitumen emulsion 16.31.2.1 On W.B.M / W.M.M. @ 0.4kg/sqm 16.31.2.2 On bituminous surface @ 0.25kg/sqm Note : Use of item no. 16.31.1 shall be restricted only for sites at sub zero temperature or for emergency applications.
16.32
2 cm premix carpet surfacing with 1.8 cum and 0.90 cum of stone chippings of 13.2 mm size and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). 16.32.1 16.32.2 16.32.3 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt With paving Asphalt grade VG - 30 with no solvent With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP: 53 sqm sqm sqm 135.00 134.00 136.70
266
Description 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). 16.33.1 16.33.2 16.33.3 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt With paving Asphalt grade VG - 30 with no solvent With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP: 53
Unit
Rate
16.34
2 cm premix carpet surfacing with 2.4 cum of stone chippings 11.2 mm nominal size per 100 sqm and bitumen emulsion (medium setting min. 65% bitumen content) complying with IS : 8887, using 96 kg per cum of chippings, including consolidation with road roller of 6 to 9 tonne capacity etc. complete. 2.5 cm premix carpet surfacing with 3 cum of stone chippings 10 mm nominal size per 100 sqm and bitumen emulsion (medium setting min. 65% bitumen contents) complying with IS : 8887, using 96 kg per cum of chippings of road surface, including consolidation with road roller etc complete . Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade, including required key aggregate as specified, spreading coarse aggregate with the help of self propelled/ tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : 16.36.1 For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm. For 75 mm compacted thickness in two layers using stone aggregate of size 63-41 mm graded @ 0.90 cum per 10 sqm key aggregate of size 20.0 mm graded @ 0.18 cum per 10 sqm. With paving asphalt grade VG - 10 @ 68 kg/10 sqm.
sqm
124.15
16.35
sqm
150.90
16.36
sqm
355.30
16.36.2
sqm
505.60
MASTIC AND BITUMASTIC WEARING COURSE 16.37 Providing and laying bitumen mastic wearing course (as per specifications) with industrial bitumen of grade 85/25 conforming to IS : 702, prepared by using mastic cooker and laid to required level and slope, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of approved size at the rate of 0.005 cum per 10 sqm and at approximate spacing of 10 cm centre to centre in both directions, pressed into surface protruding 1 mm to 4 mm over mastic surface, including cleaning the surface, removal of debris etc. all complete. (Considering bitumen using 10.2% as per MORTH specification). 16.37.1 16.37.2 25mm thick 40 mm thick sqm sqm 728.05 1,164.85
267
Description 2.5 cm thick bitumastic sheet with hot bitumen of approved quality, using stone chippings (60% with 12.5 mm nominal size and 40% with 10 mm nominal size) @ 1.65 cum per 100 sqm and coarse sand @ 1.65 cum per 100 sqm of road surface and with bitumen @ 56 kg/cum of stone chippings and @ 128 kg/cum of sand over a tack coat with hot straight run bitumen, including consolidation with road roller of 8 to 10 tonne etc. complete. (tack coat to be paid separately) : 16.38.1 16.38.2 16.38.3 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt With paving Asphalt grade VG - 30 With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP : 53
Unit
Rate
16.39
4 cm thick bitumastic sheet with hot bitumen of approved quality, using stone chippings (60% with 12.5 mm nominal size and 40% with 10 mm nominal size) @ 2.60 cum per 100 sqm and coarse sand @ 2.60 cum per 100 sqm of road surface and with bitumen @ 56 kg/cum of stone chippings and @ 128 kg/cum of sand over a tack coat with hot straight run bitumen, including consolidation with road roller of 8 to 10 tonne etc. complete. (tack coat to be paid separately) : 16.39.1 16.39.2 16.39.3 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt With paving asphalt grade VG - 30 with no solvent With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP : 53 sqm sqm sqm 346.85 345.45 352.45
SEAL COAT 16.40 Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete. Providing and laying seal coat over prepared surface of road with bitumen heated in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road surface, including rolling and finishing with power road roller all complete. Note : Seal coat items to be operated only with the prior approval of Chief Engineer concerned. CONCRETE PAVEMENT 16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy
sqm
61.30
16.41
sqm
80.15
cum
4,502.55
16.43
268
Code No.
Description M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. 16.43.1 16.43.2 Cement concrete prepared with batch mixing machine Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer
Unit
Rate
cum
5,619.50
5,967.95 43.00
16.44 16.45
Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete. Providing and fixing in position pre-moulded joint filler in expansion joints.
2.40
16.46 16.46.1
Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade 'A' sealing compound. per cm depth per cm width per m length
1.65
PAINTING ROAD / RUNWAY MARKING 16.47 Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete. 16.47.1 16.47.2 16.48 New work (Two or more coats) Old work (One or more coats) sqm sqm 94.90 58.95
Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. 16.48.1 16.48.2 New work (Two or more coats) Old work (One or more coats) sqm sqm 95.75 62.10
MISCELLANEOUS 16.49 Making bell mouth opening/ entrance of size 100x50x50 cm for drainage pipe under footpath, including providing cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) for shape of bell mouth, including plastering providing and fixing precast R.C.C./ S.F.R.C. slab including plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on exposed surface of the slab & bell mouth including centring, shuttering & neat cement punning inside the bell mouth etc. all complete.
each
1,495.55
269
Description Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. Preparation of sub-base road pavement with commercial dry lime (slaked), fly ash stabilised soil with a mix of 3% lime, 12% fly ash and 85% local suitable soil by weight, so as to achieve minimum field C.B.R. of 20, including mixing, rolling with road roller curing etc. all complete. 16.51.1 Minimum thickness 15 cm
Unit
Rate
each
234.00
16.51
cum
535.60
16.52
Providing and fixing precast lime fly ash concrete blocks 1:2:3:6 (1 lime: 2 fly ash : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), including finishing with 10mm thick cement mortar 1:3 (1 cement : 3 coarse sand) in foot paths, including preparation of sub grade with a hand rammer, laying 10 mm thick leveling course of fine sand (jamuna sand) and filling the joints with fine sand. Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. 16.54.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
cum
5,211.10
16.53
metre
269.20
16.54
cum
8,331.55
16.54.2
cum
8,095.65
270
Description Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. 16.55.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.5 0% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @3.50% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
Unit
Rate
cum
6,374.25
16.55.2
cum
6,149.90
16.56
Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 16.56.1 25 mm compacted thickness with bitumen of grade VG30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 25 mm compacted thickness with bitumen of grade VG30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
sqm
208.15
16.56.2
sqm
202.25
16.57
Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 16.57.1 40/50 mm compacted thickness with bitumen of grade VG-30 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade VG-30 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and waste plastic additive @8% (percentage by weight of bitumen) prepared in Batch Type Hot Mix Plant of 100120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade PMB-40 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.
cum
9,077.05
16.57.2
cum
9,558.65
16.57.3
cum
9,513.50
271
Code No.
Description 16.57.4 40/50 mm compacted thickness with bitumen of grade CRMB-60 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade VG-30 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity. 40/50 mm compacted thickness with bitumen of grade VG-30 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and waste plastic additive @8% (percentage by weight of bitumen) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity. 40/50 mm compacted thickness with bitumen of grade PMB-40 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity. 40/50 mm compacted thickness with bitumen of grade CRMB-60 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
Unit
Rate
cum
9,122.20
16.57.5
cum
8,836.20
16.57.6
cum
9,317.85
16.57.7
cum
9,272.70
16.57.8
cum
8,881.40
16.58 16.59
Deleted. Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer--in-charge. 16.59.1 16.59.2 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm sqm 4,580.35
sqm
3,298.40
272
Description Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). 16.60.1 Overhead informatory road signage
Unit
Rate
sqm
4,516.50
16.61
Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge. Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge.
sqm
5,061.65
16.62
sqm
505.80
16.63
sqm
291.95
16.64
sqm
97.55
273
Description Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge. Excavating holes upto 0.10 cum, including getting out the excavated soil, then returning the soil as deported in layers not exceeding 20 cm in depth, including consolidating and deposited layer by ramming watering etc., disposing of surplus excavated soil as directed with in a lead of 50 mm and lift upto 1.5 m. 16.66.1 All kind of soil
Unit
Rate
each
562.55
16.66
each
13.85
16.67
Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-charge. Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. 16.70.1 16.70.2 Made of G.I. wire of dia 4 mm Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade
sqm
502.20
16.68
sqm
536.65
16.69
cum
5,046.80
16.70
sqm sqm
486.20 519.15
16.71
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site. Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete.(Payment for Stone to be made separately).
sqm cum
586.25 607.55
16.72 16.73
sqm
181.05
274
Description 75 mm thick back filling for pitching including supplying of required materials and consolidation etc. complete with : 16.74.1 16.74.2 16.74.3 Moorum Stone aggregate 20 mm nominal size Stone aggregate 40 mm nominal size
Unit
Rate
16.75
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).
cum
6,067.10
16.76 16.77
Deduct for using of M-20 grade concrete instead of M-25 grade concrete in C.C. pavement. Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material within all lifts and lead upto 1km (by mechanical means). Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. 16.78.1 16.78.2 16.78.3 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20
cum
164.95
sqm
2.90
16.79
Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as
cum.
1,960.60
16.80
275
Code No.
Description per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-incharge.
Unit
Rate
cum
2,896.15
16.81
Providing and erecting 2.00 metre high temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-inCharge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work). Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin-charge. (Old CC paver blocks shall be supplied by the department free of cost). Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5 mm), including making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost)
metre
1,078.65
16.82
metre
10.80
16.83
sqm
36.35
16.84
sqm
159.20
16.85
metre
32.10
276
SANITARY INSTALLATIONS
277
279
Code No. 1363 1369 1373 1374 1392 1396 1397 1532 1533 1534 1535 1540 1541 1542 1543 1614 1616 1617 1620 1621 1624 1625 1627 1628 1630
Description Vitreous china foot rests 250x130x30 mm S.C.I. gully or nahani grating 100 mm dia Rubber insertions for 80 mm dia pipe joints Rubber insertions for 100 mm dia pipe joints Mirror of superior make glass 60x45 cm Vitreous china pedestal for wash basin Pig lead Flush pipe with union spreaders and clamps all in C.P. brass for single stall Flush pipe with union spreaders and clamps all in C.P. brass for double stall Flush pipe with union spreaders and clamps all in C.P. brass for range of three stall Flush pipe with union spreaders and clamps all in C.P. brass for range of four stall Flush pipe and spreaders G.I.for single set of one squatting plate urinal Flush pipe and spreaders G.I.for range of two squatting plates urinal Flush pipe and spreaders G.I.for range of three squatting plates urinal each Flush pipe and spreaders G.I.for range of four squatting plates urinal G.I. inlet connection S.C.I. soil, waste and vent single socketed pipe1.80 metres long: 75 mm dia S.C.I. soil, waste and vent single socketed pipe1.80 metres long: 100 mm dia S.C.I. plain bend 75 mm dia S.C.I. plain bend 100 mm dia S.C.I. bend with access door 75 mm dia S.C.I. bend with access door 100 mm dia S.C.I. plain single equal junctions 75x75x75 mm dia S.C.I. plain single equal junctions 100x100x100 mm dia S.C.I. single equal junctions 75x75x75 mm dia with access door
Unit pair each each each each each kilogram each each each each each each each each each each each each each each each each each each
Rate 90.00 15.00 11.00 14.00 290.00 650.00 90.00 240.00 380.00 490.00 570.00 170.00 230.00 290.00 365.00 61.00 890.00 990.00 170.00 210.00 187.00 233.00 240.00 310.00 260.00
280
Code No. 1631 1633 1634 1636 1637 1639 1640 1653 1656 1659 1662 1666 1667 1669 1670 1672 1673 1674 1677 1682 1683 1685 1686 1863 1871 1872 1875 1876 1881 1885
Description S.C.I. single equal junctions 100x100x100 mm dia with access door S.C.I. plain double equal junctions 75x75x75x75 mm dia S.C.I. plain double equal junctions100x100x100x100 mm dia S.C.I. double equal junctions 75x75x75x75 mm dia with access door S.C.I. double equal junctions 100x100x100x100 mm dia with access door Slotted cowl (terminal guard ) 75 mm dia Slotted cowl (terminal guard ) 100 mm dia Sand cast iron S&S plain single unequal junctions : 100x100x 75 mm dia Sand cast iron S&S single unequal junctions: 100x100x75 mm dia with access door. Sand cast iron S&S plain double unequal junctions : 100x100x75x 75 mm dia Sand cast iron S&S double unequal junctions: 100x100x75x75 mm dia with access door. Sand cast iron heel rest bend 75 mm dia Sand cast iron heel rest bend 100 mm dia S.C.I. single equal invert branch of required degree 75x75x75 mm dia S.C.I. single equal invert branch of required degree 100x100x100 mm dia S.C.I. double equal invert branch of required degree 75x75x75x75 mm dia
Unit
Rate
each each each each each each each each each each each each each each each each
350.00 335.00 490.00 395.00 530.00 137.00 187.00 350.00 390.00 510.00 550.00 200.00 239.00 290.00 387.00 382.00 510.00 466.00 545.00 253.00 350.00 98.00 133.00 1,350.00 820.00 1,525.00 310.00 293.00 40.00 170.00
S.C.I. double equal invert branch of required degree 100x100x100x100 mm dia each S.C.I. single unequal invert branch of required degree 100x100x75 mm dia S.C.I. double unequal invert branchof required degree 100x100x75x75 mm dia S.C.I. door pieces 75 mm dia S.C.I. door pieces 100 mm dia S.C.I. collar 75 mm dia S.C.I. collar 100 mm dia Fire clay kitchen sink: 600x450x250 mm White vitreous china laboratory sink 450x300x150 mm White vitreous china laboratory sink 600x450x200 mm White plastic seat (solid)with lid C.P.brass hinges and rubber buffers Black plastic seat (solid) with lid C.P.brass hinges and rubber buffers Spun yarn 15 mm C.P.brass tap each each each each each each each each each each each kilogram each
281
Code No. 1889 1891 1893 1895 1896 1897 1898 1913 1915 1947 1949 1950 1951 1952 1953 1954 1955 1965
Description C.P.brass toilet paper holder of standard size C.I. trap for standard urinal with vent arm with operating and other couplings in C.P.brass: 50 mm dia C.I. trap for standard urinal with vent arm with operating and other couplings in C.P.brass: 80 mm dia C.P.brass trap 40 mm dia 100 mm S.C.I. trap with vent heel 100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet 100 mm S.C.I. trap with 100 mm inlet and75 mm outlet Vitreous china lipped front urinal Vitreous china squatting plate urinal Vitreous china flat back wash basin 630x450 mm Vitreous china angle back wash basin 600x480 mm Vitreous china angle back wash basin 400x400 mm C.P. brass waste 32 mm C.P. brass waste 40 mm Vitreous china Indian type w.c. pan size 580 mm Vitreous china orrisa type w.c. pan size 580 mm Vitreous china pedestal type water closet White vitreous china dual purpose closet (Anglo Indian W.C.) suitable for use as squatting pan or European type water closet as per manufacturer's specifications Vitreous china foot rests 250x125x25 mm Carriage of Stone aggregate below 40 mm nominal size Carriage of Coarse sand Carriage of Steel Carriage of Cement Vitreous china Surgeon type wash basin of size 660x460 mm 600x120 mm glass shelf with anodised aluminium angle frame, C.P. brass brackets and guard rail of standard size Vitreous china flat back wash basin 550x400 mm CP Brass Union 40 mm dia C.C.I.(spun) socketed soil, waste and vent pipe 1.80 metres long: 100mm dia
Unit each each each each each each each each each each each each each each each each each
Rate 115.00 158.00 200.00 125.00 308.00 263.00 198.00 460.00 740.00 675.00 580.00 405.00 55.00 62.00 340.00 750.00 680.00
each pair cum cum tonne tonne each each each each each
1,250.00 100.00 87.60 87.60 77.87 77.87 995.00 130.00 530.00 175.00 1,130.00
1970 2202 2203 2205 2209 3213 3228 3229 3617 3620
282
Code No. 3621 3624 3625 3628 3629 3634 3635 3640 3641 3644 3645 3650 3651 3654 3655 3660 3664 3670 3674 3681 3682 3685 3686 3690 3695 3699 3707 3708
Description C.C.I.(spun) socketed soil, waste and vent pipe 1.80 metres long: 75 mm dia S.C.I. S&S bends with access door 100 mm dia S.C.I. S&S bends with access door 75 mm dia S.C.I. S&S bend 100 mm dia S.C.I. S&S bend 75 mm dia S.C.I. S&S heel rest sanitary bend 100 mm dia S.C.I. S&S heel rest sanitary bend 75 mm dia S.C.I. S&S single equal junctions 100x100x100 mm S.C.I. S&S single equal junctions 75x75x75 mm S.C.I. S&S single equal junctions with access door 100x100x100 mm S.C.I. S&S single equal junctions with access door 75x75x75 mm S.C.I. S&S double equal junctions 100x100x100x100 mm S.C.I. S&S double equal junctions 75x75x75x75 mm S.C.I. S&S double equal junctions with access door 100x100x100x 100 mm S.C.I. S&S double equal junctions with access door 75x75x75x75 mm S.C.I. S&S single unequal junctions 100x100x75 mm S.C.I. S&S single unequal junctions with access door 100x100x75 mm S.C.I. S&S double unequal junctions 100x100x75x75 mm S.C.I. S&S double unequal junctions with access door 100x100x75x75 mm S.C.I. S&S single equal invert branch of required degree 100x100x 100 mm dia S.C.I. S&S single equal invert branch of required degree 75x75x75 mm dia S.C.I. S&S double equal invert branch of required degree 100x100x100x 100 mm dia S.C.I. S&S double equal invert branch of required degree 75x75x75x 75 mm dia S.C.I. S&S single unequal invert branch of required degree 100x100x 75 mm dia S.C.I. S&S double unequal invert branch of required degree 100x100x 75x75 mm dia S.C.I. S&S, 75 mm offset for 75 mm dia pipe S.C.I. S&S, 150 mm offset for 75 mm dia pipe S.C.I. S&S, 150 mm offset for 100 mm dia pipe
Unit
Rate
each each each each each each each each each each each each each each each each each each each each each each each each each each each each
985.00 270.00 215.00 235.00 175.00 275.00 240.00 430.00 310.00 465.00 350.00 565.00 450.00 610.00 475.00 560.00 630.00 780.00 850.00 395.00 303.00 525.00 405.00 505.00 700.00 215.00 270.00 370.00
283
Code No. 3712 3713 3716 3717 3728 3729 3733 3734 3738 3739 3746 3747 3749 4202 7004 7005 7006 7048 7095 7096 7097 7098 7101 7102 7103 7104 7105 7106
Description S.C.I. S&S, 114 mm offset for 75 mm dia pipe S.C.I. S&S, 114 mm offset for 100 mm dia pipe S.C.I. S&S, 152 mm offset for 75 mm dia pipe S.C.I. S&S, 152 mm offset for 100 mm dia pipe S.C.I. S&S door pieces 100 mm dia S.C.I. S&S door pieces 75 mm dia S.C.I. S&S, Slotted Cowl (Terminal Guard) 100 mm S.C.I. S&S, Slotted Cowl (Terminal Guard) 75 mm S.C.I. S&S, collars 100 mm S.C.I. S&S, collars 75 mm S.C.I. S&S, 75 mm offset for 75 mm dia pipe S.C.I. S&S, 75 mm offset for 100 mm dia pipe Vitreous china toilet paper holder of standard size Red oxide Zinc chromate primer Vitreous china flat back wash basin 450x300 mm Vitreous china 10 litres low level cistern without fittings Vitreous china 10 litres low level cistern with fittings Rawl plug 50 mm (designation 10 no.) Stainless steel kitchen sink - with drain board bowl depth 250 mm Stainless steel kitchen sink - with drain board 510 x 1040mm bowl depth 225 mm Stainless steel kitchen sink - with drain board 510 x 1040mm bowl depth 200 mm Stainless steel kitchen sink - with drain board 510x1040mm bowl depth 178 mm Stainless steel kitchen sink - without drain board 610x510mm bowl depth 200 mm Stainless steel kitchen sink - without drain board 610x460mm bowl depth 200 mm Stainless steel kitchen sink - without drain board 470x420mm bowl depth 178 mm Coloured Orissa pattern W.C. pan 580x440 mm Coloured Pedestal type W.C. pan 580x440 mm (European type) Coloured Vitreous china 10 lit. low level cistern
Unit each each each each each each each each each each each each each litre each each each each each each each each each each each each each each
Rate 270.00 355.00 335.00 440.00 370.00 260.00 190.00 175.00 185.00 130.00 215.00 246.00 118.00 68.00 425.00 890.00 1,550.00 10.00 5,150.00 4,900.00 4,200.00 2,900.00 2,950.00 2,750.00 2,050.00 1,275.00 1,080.00 1,500.00
284
Code No. 7107 7112 7113 7114 7115 7116 7117 7118 7119 7120 7123 7126 7127 7358 7359 7361 7363 7364 7375 7376 7377 7378 7379
Description Coloured (other than black) solid P.V.C. seat in European W.C. pan Circular shape 450 mm dia Mirror with Plastic moulded frame Rectangular shape 453x357 mm Mirror with Plastic moulded frame Oval shape 450x350 mm (outer dimensions) Mirror with Plastic moulded frame Rectangular shape 1500x450 mm Mirror with Plastic moulded frame Hard board 6 mm thick Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings Flexible (coil shaped) PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings Coloured High density polyethylene/ poly propylene 10 lit. (full flush) capacity controlled low level flushing cistern with fittings White Vitreous china 10 litres (full flush) capacity controlled low level flushing cistern with all fittings
Unit each each each each each sqm each each each each each each
Rate 475.00 390.00 260.00 300.00 670.00 170.00 21.00 27.00 26.00 28.00 685.00 975.00 1,400.00 640.00 490.00 530.00 600.00 525.00 440.00 1,010.00 1,240.00 1,800.00 1,440.00
Coloured Vitreous china 10 litres (full flush) capacity controlled low level flushing cistern with all fittings each Flushing Cistern P.V.C. 10 litres capacity ( low level ) (White) (with fittings, accessories and flush pipe) P.V.C. automatic flushing cistern 5 litres capacity P.V.C. automatic flushing cistern 10 litres capacity 15 mm C.P. brass tap with elbow operation lever White glazed fire clay draining board 600x450x25 mm G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Single lipped urinal G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of two lipped urinals G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of three lipped urinals G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe Range of four lipped urinals White vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per IS : 2556 each each each each each each each each each each
285
Code No. 7491 7492 7493 7494 7503 7504 7505 7506 7507 7508 7805 7806 7807 7808 7809 7858 9999
Description PTMT - Waste Coupling 31/32 mm PTMT - Waste Coupling 38/40 mm PTMT - Bottle Trap 31/32 mm PTMT - Bottle Trap 38/40 mm PTMT - Liquid Soap Container of 400 ml capacity PTMT - Towel Ring 215x200x37 mm PTMT- Towel Rail (450 mm) PTMT - Towel Rail (600 mm) PTMT - Shelf 450x124x36 mm PTMT - Urinal Spreader 15 mm Salem Stainless steel AISI - 304 (18/8) Orrisa pattern W.C. pan 724 mm X 578 mm Salem Stainless steel AISI - 304 (18/8) Round basin 405mm X355 mm Salem Stainless steel AISI - 304 (18/8) Wash basin 530 mm X 345 mm each Centrifugally cast (spun) iron S&S 100 mm inlet and 100 mm outlet Centrifugally cast (spun) iron S&S 100 mm inlet and 75 mm outlet P.T.M.T. Urinal cock 15mm dia Sundries NEW CODES
Unit each each each each each each each each each each each each each each each each L.S.
Rate 51.00 64.00 317.00 345.00 145.00 116.00 192.00 226.00 258.00 127.00 3,630.00 1,690.00 1,470.00 392.00 424.00 94.00 1.49
Wall mounted water closet Adjustable Vetrious China Cistern with fittings White Vetrious China Waterless Urinal Cistern with fittings for Waterless Urinal White Vetrious Urinal
286
each
6,309.20
17.2
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 17.2.2 W.C. pan with ISI marked white solid plastic seat and lid W.C. pan with ISI marked black solid plastic seat and lid each each 2,885.10 2,865.35
17.3
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 17.3.2 W.C. pan with ISI marked white solid plastic seat and lid W.C. pan with ISI marked black solid plastic seat and lid each each 4,220.80 4,201.05
17.4
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.1 17.4.2 17.4.3 17.4.4 One urinal basin with 5 litre white P.V.C. automatic flushing cistern Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern each each each each 2,844.40 4,652.80 6,229.90 8,528.75
17.5
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass,
287
Code No.
Description including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 17.5.2 17.5.3 17.5.4 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern
Unit
Rate
17.6
Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1 17.6.2 17.6.3 17.6.4 Single squatting plate with 5 litre P.V.C. automatic flushing cistern Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern each each each each 3,529.35 5,152.40 6,826.65 8,272.05
17.7
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 17.7.1 17.7.2 17.7.3 17.7.4 17.7.5 17.7.6 17.7.7 17.7.8 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap White Vitreous China Angle back wash basin size 600x 480 mm with single 15 mm C.P. brass pillar tap White Vitreous China Angle back wash basin size 400x 400 mm with single 15 mm C.P. brass pillar tap White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI marked each each each each each each each 1,848.35 1,628.95 1,679.95 1,460.50 1,518.60 1,315.35 1,338.55
each
3,218.95
17.7.9
each
2,500.05
288
Code No.
Description 17.7.10 17.7.11 Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap
Unit
Rate
each each
2,807.85 2,552.35
17.8
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required : 17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 mm
each
894.70
17.9
each
2,206.95
17.10
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board each each each each each each each 6,743.55 6,453.15 5,640.10 4,130.15 3,934.30 3,702.00 2,888.95 17.10.1.1 510x1040 mm bowl depth 250 mm 17.10.1.2 510x1040 mm bowl depth 225 mm 17.10.1.3 510x1040 mm bowl depth 200 mm 17.10.1.4 510x1040 mm bowl depth 178 mm
17.10.2
Kitchen sink without drain board 17.10.2.1 610x510 mm bowl depth 200 mm 17.10.2.2 610x460 mm bowl depth 200 mm 17.10.2.3 470x420 mm bowl depth 178 mm
17.11
Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 17.11.1 17.11.2 Size 450x300x150 mm Size 600x450x200 mm each each 1,939.80 2,758.65
17.12
Providing and fixing draining board with C.I. brackets including painting of brackets, cutting and making good the walls wherever required : 17.12.1 White glazed fire clay draining board of size 600x450x 25 mm each 896.55
17.13
Providing and fixing white vitreous china water closet squatting pan (Indian type) : 17.13.1 17.13.2 Long pattern W.C. pan of size 580 mm Orissa pattern W.C. pan of size 580x440 mm each each 759.70 1,235.95
17.14 17.15
Extra for using coloured W.C. pan instead of white W.C. pan : 17.14.1 Orissa pattern W.C. pan 580x440 mm each each 609.80 1,154.65 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.
289
Description Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. Providing and fixing a pair of white vitreous china foot rests of standard pattern for squatting pan water closet : 17.17.1 17.17.2 250x130x30 mm 250x125x25 mm
Unit
Rate
each
1,173.10
17.17
pair pair
139.45 151.10
17.18
Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 17.18.1 17.18.2 10 litre capacity - White 10 litre capacity - coloured each each 831.90 887.35
17.19
Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 17.19.1 17.19.2 10 litre (full flush) capacity-white 10 litre (full flush) capacity-coloured each each 1,474.10 1,967.75
17.20
Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : 17.20.1 17.20.2 17.20.3 White solid plastic seat with lid Black solid plastic seat with lid Coloured (other than black & white) solid plastic seat with lid each each each 383.25 363.50 574.90
Deleted. Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : 17.25.1 17.25.2 17.25.3 17.25.4 17.25.5 17.25.6 Flat back wash basin of size 630x450 mm Flat back wash basin of size 550x400 mm Angle back wash basin of size 600x480 mm Angle back wash basin of size 400x400 mm Flat back wash basin of size 450x300 mm Surgeon type wash basin of size 660x460 mm each each each each each each 893.55 725.15 783.25 579.95 603.20 1,265.25 each 94.00
each each
792.60 1,537.85
17.24 17.25
17.26
Providing and fixing kitchen sink including making all connections excluding cost of fittings. 17.26.1 White glazed fire clay sink of size 600x450x250 mm each 1,656.65
290
Description Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings : 17.27.1 17.27.2 Size 450x300x150 mm Size 600x450x200 mm
Unit
Rate
each each
1,041.05 1,859.95
17.28
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe each each 59.50 66.45
17.28.2.1 32 mm dia 17.28.2.2 40 mm dia 17.29 17.30 17.31 Providing and fixing 100 mm sand cast Iron grating for gully trap. Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.1 17.32.2 17.32.3 17.32.4 17.33 Circular shape 450 mm dia Rectangular shape 453x357 mm Oval shape 450x350 mm (outer dimensions) Rectangular shape 1500x450 mm
each
674.05
17.32
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Providing and fixing toilet paper holder : 17.34.1 17.34.2 C.P. brass Vitreous china
each
341.25
17.34
each each
250.95 259.75
17.35
Providing and fixing soil, waste and vent pipes : 17.35.1 100 mm dia metre metre 734.30 857.30
17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 17.35.2 75 mm diameter :
17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989
SUBHEAD -17.0 SANITARY INSTALLATIONS
metre metre
656.60 744.50
291
Description Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 17.36.1 17.36.2 75 mm dia pipe 100 mm dia pipe
Unit
Rate
each each
47.55 56.00
17.37
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 17.37.1 17.37.2 For 100 mm dia pipe For 75 mm dia pipe each each 112.50 110.15
17.38
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.38.1 100 mm dia each each 310.30 353.25
17.38.1.1 Sand cast iron S&S as per IS - 1729 17.38.1.2 Sand cast iron S&S as per IS - 3989 17.38.2 75 mm dia
17.38.2.1 Sand cast iron S&S as per IS - 1729 17.38.2.2 Sand cast iron S&S as per IS- 3989 17.39 Providing and fixing plain bend of required degree. 17.39.1 100 mm dia
each each
248.65 281.15
17.39.1.1 Sand cast iron S&S as per IS - 1729 17.39.1.2 Sand cast iron S&S as per IS : 3989 17.39.2 75 mm dia
each each
267.30 296.35
17.39.2.1 Sand cast iron S&S as per IS -1729 17.39.2.2 Sand cast iron S&S as per IS - 3989 17.40 Providing and fixing heel rest sanitary bend 17.40.1 100 mm dia
each each
216.15 221.95
17.40.1.1 Sand cast iron S&S as per IS - 1729 17.40.1.2 Sand cast iron S&S as per IS - 3989 17.40.2 75 mm dia
each each
301.00 342.80
17.40.2.1 Sand cast iron S&S as per IS - 1729 17.40.2.2 Sand cast iron S&S as per IS - 3989 17.41 Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 17.41.1 100x100x100x100 mm
each each
251.00 297.45
17.41.1.1 Sand cast iron S&S as per IS - 1729 17.41.1.2 Sand cast iron S&S as per IS - 3989
SUBHEAD -17.0 SANITARY INSTALLATIONS
each each
655.05 747.95
292
Code No.
Unit
Rate
17.41.2.1 Sand cast iron S&S as per IS - 1729 17.41.2.2 Sand cast iron S&S as per IS - 3989 17.42 Providing and fixing double equal plain junction of required degree. 17.42.1 100x100x100x100 mm
each each
490.25 583.15
17.42.1.1 Sand cast iron S&S as per IS - 1729 17.42.1.2 Sand cast iron S&S as per IS - 3989 17.42.2 75x75x75x75 mm
each each
592.55 679.65
17.42.2.1 Sand cast iron S&S as per IS - 1729 17.42.2.2 Sand cast iron S&S as per IS - 3989 17.43 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.43.1 100x100x100 mm
each each
407.80 541.35
17.43.1.1 Sand cast iron S&S as per IS - 1729 17.43.1.2 Sand cast iron S&S as per IS - 3989 17.43.2 75x75x75 mm
each each
446.20 579.75
17.43.2.1 Sand cast iron S&S as per IS - 1729 17.43.2.2 Sand cast iron S&S as per IS - 3989 17.44 Providing and fixing single equal plain junction of required degree : 17.44.1 100x100x100 mm
each each
333.45 438.00
17.44.1.1 Sand cast iron S&S as per IS - 1729 17.44.1.2 Sand cast iron S&S as per IS - 3989 17.44.2 75x75x75 mm
each each
383.45 522.85
17.44.2.1 Sand cast iron S&S as per IS - 1729 17.44.2.2 Sand cast iron S&S as per IS - 3989 17.45 Providing and fixing double unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 17.45.1 100x100x75x75 mm
each each
297.45 378.75
17.45.1.1 Sand cast iron S&S as per IS - 1729 17.45.1.2 Sand cast iron S&S as per IS - 3989 17.46 Providing and fixing double unequal plain junction of required degree : 17.46.1 100x100x75x75 mm
each each
678.50 1,026.95
17.46.1.1 Sand cast iron S&S as per IS - 1729 17.46.1.2 Sand cast iron S&S as per IS - 3989
SUBHEAD -17.0 SANITARY INSTALLATIONS
each each
615.75 929.35
293
Description Providing and fixing single unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 17.47.1 100x100x75 mm
Unit
Rate
17.47.1.1 Sand cast iron S&S as per IS - 1729 17.47.1.2 Sand cast iron S&S as per IS - 3989 17.48 Providing and fixing single unequal plain junction of required degree : 17.48.1 100x100x75 mm
each each
492.65 771.40
17.48.1.1 Sand cast iron S&S as per IS - 1729 17.48.1.2 Sand cast iron S&S as per IS - 3989 17.49 Providing and fixing double equal plain invert branch of required degree: 17.49.1 100x100x100x100 mm
each each
429.90 673.85
17.49.1.1 Sand cast iron S&S as per IS - 1729 17.49.1.2 Sand cast iron S&S as per IS 3989 17.49.2 75x75x75x75 mm
each each
615.75 633.20
17.49.2.1 Sand cast iron S&S as per IS - 1729 17.49.2.2 Sand cast iron S&S as per IS - 3989 17.50 Providing and fixing single equal plain invert branch of required degree : 17.50.1 100x100x100 mm
each each
462.35 489.10
17.50.1.1 Sand cast iron S&S as per iron 1729 17.50.1.2 Sand cast iron S&S as per IS - 3989 17.50.2 75x75x75 mm
each each
472.90 482.20
17.50.2.1 Sand cast iron S&S as per IS - 1729 17.50.2.2 Sand cast iron S&S as per IS - 3989 17.51 Providing and fixing double unequal invert branch of required degree : 17.51.1 100x100x75x75 mm
each each
355.50 370.60
17.51.1.1 Sand cast iron S&S as per IS - 1729 17.51.1.2 Sand cast iron S&S as per IS - 3989 17.52 Providing and fixing single unequal plain invert branch of required degree : 17.52.1 100x100x75 mm
each each
656.40 836.45
17.52.1.1 Sand cast iron S&S as per IS - 1729 17.52.1.2 Sand cast iron S&S as per IS - 3989 17.53 Providing and fixing sand cast iron S&S off sets as per IS: 1729 17.53.1 76 mm off sets
each each
564.65 609.95
each each
268.40 304.40
294
Code No.
Unit
Rate
17.53.2.1 With 75 mm dia pipe 17.53.2.2 With 100 mm dia pipe 17.53.3 152 mm off sets
each each
337.00 435.70
17.53.3.1 With 75 mm dia pipe 17.53.3.2 With 100 mm dia pipe 17.54 Providing and fixing sand cast iron S&S off sets as per IS: 3989 : 17.54.1 75 mm off sets
each each
420.15 542.10
each
268.40
17.54.2.1 With 75 mm dia pipe 17.54.2.2 With 100 mm dia pipe 17.55 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 17.55.1 100 mm
each each
341.50 457.65
17.55.1.1 Sand cast iron S&S as per IS - 1729 17.55.1.2 Sand cast iron S&S as per IS - 3989 17.55.2 75 mm
each each
446.20 469.40
17.55.2.1 Sand cast iron S&S as per IS - 1729 17.55.2.2 Sand cast iron S&S as per IS - 3989 17.56 Providing and fixing terminal guard : 17.56.1 100 mm
each each
325.30 333.45
17.56.1.1 Sand cast iron S&S as per IS - 1729 17.56.1.2 Sand cast iron S&S as per IS - 3989 17.56.2 75 mm
each each
240.60 244.10
17.56.2.1 Sand cast iron S&S as per IS - 1729 17.56.2.2 Sand cast iron S&S as per IS - 3989 17.57 Providing and fixing collar : 17.57.1 100 mm
each each
177.80 221.95
17.57.1.1 Sand cast iron S&S as per IS - 1729 17.57.1.2 Sand cast iron S&S as per IS - 3989 17.57.2 75 mm
each each
177.85 238.25
17.57.2.1 Sand cast iron S&S as per IS - 1729 17.57.2.2 Sand cast iron S&S as per IS - 3989
SUBHEAD -17.0 SANITARY INSTALLATIONS
each each
132.50 169.65
295
Description Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 17.58.1 17.58.2 17.58.3 100 mm 75 mm 50 mm
Unit
Rate
17.59
Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 17.59.1 17.59.2 17.59.3 100 mm 75 mm 50 mm each each each 61.70 52.35 45.45
17.60
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 17.60.1 100 mm inlet and 100 mm outlet each each 801.70 651.85
17.60.1.1 Sand cast iron S&S as per IS: 3989 17.60.1.2 Sand Cast Iron S&S as per IS: 1729 17.60.2 100 mm inlet and 75 mm outlet
17.60.2.1 Sand cast iron S&S as per IS - 3989 17.60.2.2 Sand Cast Iron S&S as per IS- 1729 17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 17.61.1 17.61.2 17.61.3 17.62 100 mm dia 75 mm dia 50 mm dia
each each
838.85 576.35
Painting C.I. cistern with bitumastic or any other anti-corrosive paint inside and white paint over a coat of zinc chromate yellow primer (of approved quality ) on the outside surface of the cistern, flush pipe, other fittings, etc. complete for new work. Re-painting C.I. cistern with bitumastic or any other anti-corrosive paint inside and white paint on the outside surface of the cistern, flush pipe, other fittings, etc. complete, including polishing of wooden seat and lid and cleaning of W.C. pan with acid wherever necessary. Repainting C.I. cistern with synthetic enamel paint of approved colour, brand and manufacture on the outside surface of cistern, flush pipe, other fittings etc. complete. Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 17.65.1 17.65.2 100 mm diameter pipe 75 mm diameter pipe
each
338.10
17.63
each
237.35
17.64
each
100.60
17.65
metre metre
28.75 22.00
296
Description Repainting sand cast iron/ centrifugally cast iron (spun) iron, soil, waste, vent pipes and fittings with one coat of synthetic enamel paint of any colour such as chocolate, grey or buff etc : 17.66.1 17.66.2 100 mm diameter pipe 75 mm diameter pipe
Unit
Rate
17.67 17.68
Repainting bath tub of size 1700x730x430 mm with enamel paint. Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.68.1 White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.
each
5,744.30
17.69
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 17.69.2 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms each each 94.35 109.45
17.70
Providing and fixing PTMT Bottle Trap for Wash basin and sink. 17.70.1
each
403.30
17.70.2
each
435.30
17.71
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms
each
180.10
17.72
each
169.85
17.73
each
375.70
17.73.2
each
415.20
297
Description Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms. Providing and fixing PTMT urinal cock of approved quality and colour. 17.76.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms
Unit
Rate
each
452.35
17.75
each
159.20
17.76
each
123.15
17.77
Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. 17.77.1 17.77.2 17.77.3 Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe) Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes) Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes) each each each 168.00 205.50 242.90
NEW ITEMS 17.78 Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal. Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
each
9,444.35
17.79
each
19,178.40
17.80
each
14,961.65
298
WATER SUPPLY
299
301
Code No. 1397 1464 1466 1468 1470 1472 1545 1546 1547 1548 1549 1550 1551 1552 1555 1559 1608 1612 1641 1642 1643 1644 1645 1646 1647 1648 1649 1687 1688 1689
Description Pig lead S & S.C.I.standard specials up to 300 mm dia (heavy class) S & S.C.I.standard specials over 300 mm dia (heavy class) Flanged C.I. standard specials up to 300 mm dia (heavy class) Flanged C.I. standard specials over 300 mm dia (heavy class) Casing pipe 100 mm dia G.I. pipes 15 mm dia G.I. pipes 20 mm dia G.I. pipes 25 mm dia G.I. pipes 32 mm dia G.I. pipes 40 mm dia G.I. pipes 50 mm dia G.I. pipes 65 mm dia G.I. pipes 80 mm dia G.I. back (jam) nuts 25 mm dia G.I. back (jam) nuts 65 mm dia G.I. tees (equal) 25 mm G.I. tees (equal) 65 mm G.I. Union 15 mm nominal bore G.I. Union 20 mm nominal bore G.I. Union 25 mm nominal bore G.I. Union 32 mm nominal bore G.I. Union 40 mm nominal bore G.I. Union 50 mm nominal bore G.I. Union 65 mm nominal bore G.I. Union 80 mm nominal bore Polyethylene water storage tank with cover and suitable locking arrangement Unplasticised P.V.C. connection pipe with brass union 30 cm long 15 mm bore Unplasticised P.V.C. connection pipe with brass union 30 cm long 20 mm bore Unplasticised P.V.C. connection pipe with brass union 45 cm long 15 mm bore
Unit kilogram quintal quintal quintal quintal metre metre metre metre metre metre metre metre metre each each each each each each each each each each each each per litre each each each
Rate 90.00 3,450.00 3,550.00 5,300.00 5,600.00 335.00 81.00 97.00 134.00 167.00 202.00 254.00 325.00 426.00 8.00 18.00 42.00 270.00 40.00 60.00 70.00 100.00 135.00 180.00 390.00 480.00 4.45 26.00 33.00 33.00
302
Code No. 1690 1693 1878 1879 1881 1882 1922 1923 1924 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1940 1941 1942 1943 1944 1945 1956 1957 1958 1959 1960
Description Unplasticised P.V.C. connection pipe with brass union 45 cm long 20 mm bore S.C.I. hand pump Shower rose C.P.brass for 15 to 20 mm inlet 100 mm dia Shower rose C.P.brass for 15 to 20 mm inlet 150 mm dia Spun yarn Strainer brass 40 mm dia 1.5 metre long H.P. or L.P. ball valve with polythene floats: 15 mm dia H.P. or L.P. ball valve with polythene floats: 20 mm dia H.P. or L.P. ball valve with polythene floats: 25 mm dia Brass full way valve with C.I. wheel (screwed end) 25 mm dia Brass full way valve with C.I. wheel (screwed end) 32 mm dia Brass full way valve with C.I. wheel (screwed end) 40 mm dia Brass full way valve with C.I. wheel (screwed end) 50 mm dia Brass full way valve with C.I. wheel (screwed end) 65 mm dia Brass full way valve with C.I. wheel (screwed end) 80 mm dia Gunmetal non-return valve-horizontal (screwed end) 25 mm dia Gunmetal non-return valve-horizontal (screwed end) 32 mm dia Gunmetal non-return valve-horizontal (screwed end) 40 mm dia Gunmetal non-return valve-horizontal (screwed end) 50 mm dia Gunmetal non-return valve-horizontal (screwed end) 65 mm dia Gunmetal non-return valve-horizontal (screwed end) 80 mm dia C.I.sluice valve (with caps) class I : 100 mm dia C.I.sluice valve (with caps) class I : 125 mm dia C.I.sluice valve (with caps) class I : 150 mm dia C.I.sluice valve (with caps) class I : 200 mm dia C.I.sluice valve (with caps) class I : 250 mm dia C.I.sluice valve (with caps) class I : 300 mm dia Bolts and nuts 16 mm dia 60 mm long Bolts and nuts 16 mm dia 65 mm long Bolts and nuts 20 mm dia 65 mm long Bolts and nuts 20 mm dia 70 mm long Bolts and nuts 20 mm dia 75 mm long
Unit
Rate
each each each each kilogram each each each each each each each each each each each each each each each each each each each each each each each each each each each
43.00 550.00 40.00 55.00 40.00 495.00 190.00 270.00 315.00 305.00 370.00 450.00 650.00 900.00 1550.00 310.00 400.00 510.00 780.00 1,420.00 2,030.00 2,300.00 2,600.00 3,410.00 6,550.00 9,550.00 13,500.00 10.00 11.00 13.00 13.00 14.00
303
Code No. 1961 1962 1963 1964 2271 2309 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2341 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352
Description Bolts and nuts 20 mm dia 80 mm long Bolts and nuts 24 mm dia 85 mm long Bolts and nuts 24 mm dia 90 mm long Bolts and nuts 27 mm dia 100 mm long Carriage of G.I. pipes below 100 mm dia Carriage of Cast iron fittings Carriage of Spun iron S & S pipes 100 mm dia Carriage of Spun iron S & S pipes 125 mm dia Carriage of Spun iron S & S pipes 150 mm dia Carriage of Spun iron S & S pipes 200 mm dia Carriage of Spun iron S & S pipes 250 mm dia Carriage of Spun iron S & S pipes 300 mm dia Carriage of Spun iron S & S pipes 350 mm dia Carriage of Spun iron S & S pipes 400 mm dia Carriage of Spun iron S & S pipes 450 mm dia Carriage of Spun iron S & S pipes 500 mm dia Carriage of Spun iron S & S pipes 600mm dia Carriage of C.I. pipes 500 mm dia Carriage of R.C.C. pipes 900 mm dia Carriage of R.C.C. pipes 1000 mm dia Carriage of R.C.C. pipes 1100 mm dia Carriage of R.C.C. pipes 1200 mm dia Carriage of Pig lead Carriage of Ductile iron pipes (k7) 100 mm dia Carriage of Cast iron pipes 150 mm dia Carriage of Cast iron pipes 200 mm dia Carriage of Cast iron pipes 250 mm dia Carriage of Cast iron pipes 300 mm dia Carriage of Cast iron pipes 350 mm dia Carriage of Cast iron pipes 400 mm dia Carriage of Cast iron pipes 450 mm dia Carriage of Cast iron pipes 500 mm dia Carriage of Cast iron pipes 600 mm dia
Unit each each each each tonne tonne 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre tonne 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre
Rate 15.00 27.00 29.00 35.00 77.87 77.87 191.48 255.77 319.12 519.11 737.68 911.78 1,276.50 1,740.68 2,127.50 2,127.50 3,191.25 2,127.50 4,786.87 6,382.50 6,382.50 6,382.50 77.87 191.48 319.12 519.11 737.68 911.78 1,276.50 1,740.68 2,127.50 2,127.50 3,191.25
304
Code No. 2353 2355 2356 2357 3080 3084 3088 3092 3096 3300 3311 3314 3317 3320 3321 3326 7257 7258 7259 7260 7261 7400 7401 7402 7403 7405 7406 7407 7408 7409 7410 7411 7412
Description Carriage of Cast iron pipes 700 mm dia Carriage of Cast iron pipes 800 mm dia Carriage of Cast iron pipes 900 mm dia Carriage of Cast iron pipes 1000 mm dia Gunmetal non-return valve-vertical (screwed end) 25 mm dia Gunmetal non-return valve-vertical (screwed end) 32 mm dia Gunmetal non-return valve-vertical (screwed end) 40 mm dia Gunmetal non-return valve-vertical (screwed end) 50 mm dia Gunmetal non-return valve-vertical (screwed end) 65 mm dia Gunmetal non-return valve-vertical (screwed end) 80 mm dia C.I.sluice valve (with caps) class II : 100 mm dia C.I.sluice valve (with caps) class II : 125 mm dia C.I.sluice valve (with caps) class II : 150 mm dia C.I.sluice valve (with caps) class II : 200 mm dia C.I.sluice valve (with caps) class II : 250 mm dia C.I.sluice valve (with caps) class II : 300 mm dia C.P. Brass bibcock 15 mm C.P. Brass long nose bibcock 15 mm C.P. Brass long body bibcock 15 mm C.P. Brass stop cock (concealed) 15 mm C.P. Brass angle valve 15 mm 15 mm PTMT bib cock 15 mm PTMT bib cock with flange (fancy) 15 mm PTMT bib cock long body with flange 15 mm dia PTMT stop cock(male thread) 20 mm dia. PTMT stop cock PTMT pillar cock PTMT push cock 15 mm dia. PTMT push cock 12 mm dia. 20 mm BSP PTMT grating 100 mm dia. PTMT Pillar cock (fancy) 15mm foam flow 125 mm grating with waste hole Rectangular type with openable circular lid 150 mm size 18 mm high with 100 mm dia. (110 gm)
Unit 100 metre 100 metre 100 metre 100 metre each each each each each each each each each each each each each each each each each each each each each each each each each each each each each
Rate 3,191.25 3,191.25 4,786.87 6,382.50 320.00 490.00 680.00 930.00 1,650.00 2,630.00 2,650.00 3,200.00 4,000.00 9,100.00 13,500.00 17,000.00 325.00 330.00 350.00 350.00 370.00 100.00 140.00 160.00 100.00 130.00 160.00 90.00 80.00 31.00 225.00 37.00 101.00
305
Code No. 7415 7416 7417 7418 7419 7420 7421 7422 7423 7424 7425 7495 7496 7497 7498 7499 7500 7501 7509 7651 7652 7653 7654 7655 7656 7657 7658 7659 7660 7661
Description Double acting air valve 50 mm Double acting air valve 80 mm Double acting air valve 100 mm Water meter (including testing charges) 80 mm Water meter (including testing charges) 100 mm Water meter (including testing charges) 150 mm Water meter (including testing charges) 200 mm Dirt box strainer 80 mm Dirt box strainer 100 mm Dirt box strainer 150 mm Dirt box strainer 200 mm PTMT - Ball Cock 15 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 20 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 25 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT- Ball Cock 40 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT - Ball Cock 50 mm Complete with Epoxy Coated Aluminium Rod & H.D. Ball PTMT- Angle Stop cock with Flange 15 mm PTMT - Swiveling shower 15 mm PTMT- Soap Dish/Holder 138x102x75 mm Ductile Iron class K - 9 pipe Conforming to I.S. 8329 100 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 150 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 200 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 250 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 300 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 350 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 400 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 450 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 500 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 600 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 700 mm dia
Unit each each each each each each each each each each each each each each each each each each each metre metre metre metre metre metre metre metre metre metre metre
Rate 3,370.00 4,930.00 6,400.00 2,030.00 3,150.00 4,560.00 5,100.00 2,620.00 4,180.00 5,420.00 7,550.00 134.00 195.00 420.00 780.00 1,150.00 130.00 87.00 120.00 797.00 1,170.00 1,595.00 2,105.00 2,680.00 3,225.00 4,350.00 5,085.00 6,180.00 7,430.00 10,050.00
306
Code No. 7662 7663 7664 7665 7666 7668 7669 7670 7671 7672 7673 7674 7675 7676 7677 7678 7679 7680 7681 7682 7683 7684 7685 7686 7687 7688 7689 7690 7691 7692
Description Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 750 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 800 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 900 mm dia Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 1000 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 100 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 150 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 200 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 250 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 300 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 350 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 400 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 450 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 500 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 600 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 700 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 750 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 800 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 900 mm dia Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 1000 mm dia Ductile Iron K - 12 specials suitable for push on jointing upto 600 mm dia Ductile Iron K - 12 specials suitable for push on jointing over 600 mm dia Ductile Iron specials suitable for mechanical jointing as per I.S. 9523 - upto 600 mm dia Ductile Iron Specials suitable for mechanical jointing as per I.S. 9523 over 600 mm dia Ductile Iron Pipe Class K-9 flanges and welding 100 mm dia Ductile Iron Pipe Class K-9 flanges and welding 150 mm dia Ductile Iron Pipe Class K-9 flanges and welding 200 mm dia Ductile Iron Pipe Class K-9 flanges and welding 250 mm dia Ductile Iron Pipe Class K-9 flanges and welding 300 mm dia Ductile Iron Pipe Class K-9 flanges and welding 350 mm dia Ductile Iron Pipe Class K-9 flanges and welding 400 mm dia
Unit metre metre metre metre each each each each each each each each each each each each each each each quintal quintal quintal quintal metre metre metre metre metre metre metre
Rate 11,350.00 11,990.00 14,030.00 15,750.00 26.00 36.00 62.00 73.00 103.00 127.00 234.00 260.00 285.00 352.00 542.00 636.00 684.00 915.00 1,138.00 11,850.00 16,280.00 12,540.00 17,580.00 2,025.00 2,825.00 3,740.00 4,935.00 6,330.00 8,020.00 9,645.00
307
Code No. 7693 7694 7695 7696 7697 7698 7699 7700 7701 7702 7703 7704 7705 7706 7707 7708 7709 7710 7711 7712 7713 7714 7715 7716 7717 7718
Description Ductile Iron Pipe Class K-9 flanges and welding 450 mm dia Ductile Iron Pipe Class K-9 flanges and welding 500 mm dia Ductile Iron Pipe Class K-9 flanges and welding 600 mm dia Ductile Iron Pipe Class K-9 flanges and welding 700 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 100 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 125 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 150 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 200 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 250 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 300 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 350 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 400 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 450 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 500 mm dia S&S Centrifugally (Spun) C.I. Pipe class LA 600 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 suitable for lead jointing up to 300 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 suitable for lead jointing over 300 mm dia S&S Centrifugally (Spun) C.I. Pipe specials suitable for mechanical joint as per I.S. 13382 up to 300 mm dia S&S Centrifugally (Spun) C.I. Pipe Specials suitable for mechanical joint as per IS 13382 over 300 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 100 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 150 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 200 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 250 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 300 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 350 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 400 mm dia
Unit metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre quintal quintal quintal quintal metre metre metre metre metre metre metre
Rate 11,675.00 13,895.00 18,760.00 23,275.00 830.00 1,040.00 1,240.00 2,120.00 2,830.00 3,740.00 4,500.00 5,870.00 7,100.00 8,250.00 11,450.00 5,850.00 7,500.00 8,200.00 8,880.00 1,260.00 1,960.00 3,170.00 3,730.00 4,770.00 6,080.00 7,890.00
308
Code No. 7719 7720 7721 7722 7723 7724 7725 7726 7727 7728 7729 7730 7731 7732 7733 7734 7735 7859 7861 7862 7863 7864 7865 7866 8300 8301 8302 8303 8304 8305
Description Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 450 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 500 mm dia Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B conforming to I.S. 1536, - 600 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 100 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 150 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 200 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 250 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 300 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 350 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 400 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 450 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 500 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 600 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 700 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 800 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 900 mm dia Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 1000 mm dia P.T.M.T. Bib cock with nozzle 15 mm P.T.M.T. Stop cock (concealed) 15 mm 15 mm nominal bore and 30 cm length PVC connection pipe with P.T.M.T. Nuts 15 mm nominal bore and 45 cm length PVC connection pipe with P.T.M.T. Nuts P.T.M.T. extension nipple 15 mm P.T.M.T. extension nipple 20 mm P.T.M.T. extension nipple 25 mm 1216 mm PE-AL-PE Composite pressure pipe 1620 mm PE-AL-PE Composite pressure pipe 2025 mm PE-AL-PE Composite pressure pipe 2532 mm PE-AL-PE Composite pressure pipe 3240 mm PE-AL-PE Composite pressure pipe 4050 mm PE-AL-PE Composite pressure pipe
Unit
Rate
metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre each each each each each each each metre metre metre metre metre metre
9,940.00 12,390.00 15,330.00 708.00 1,035.00 1,415.00 1,920.00 2,638.00 3,135.00 3,714.00 4,411.00 5,214.00 6,801.00 8,739.00 11,156.00 14,617.00 15,485.00 133.00 173.00 33.00 38.00 32.00 38.00 57.00 90.00 111.00 143.00 193.00 310.00 335.00
309
Code No. 8625 8626 8627 8628 8629 8630 8631 8633 8634 8635 8636 8637 8638 8639 8640 8641 8642 8643 8644 8645 9999
Description Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - 16 mm Outer dia Poly propylene - Random - Co - Polymer (PPR) pipes SDR 7.4 -20 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 - 25 mm outer dia Poly propylene - Random - Co - poymer (PPR) pipes SDR 7.4 - 32 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -40 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -50 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -63 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR 7.4 -90 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR - 11 - 110 mm Outer dia Poly propylene - Random - Co - polymer (PPR) pipes SDR - 11- 160 mm Outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 15 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 20 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 32 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 40 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 50 mm outer dia Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 75 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 100 mm inner dia Chlorinated Polyvinyl - chloride (CPVC) pipe 150 mm inner dia Sundries NEW CODES
Unit
Rate
metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre L.S.
32.00 50.00 76.00 124.00 196.00 286.00 445.00 1,020.00 1,070.00 2,255.00 51.00 63.00 90.00 120.00 170.00 280.00 835.00 1,185.00 1,640.00 2,870.00 1.49
3327
each
5,822.50
310
Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc. 18.2.1 18.2.2 18.2.3 18.2.4 1216 (16 mm OD) pipe 1620 (20 mm OD) pipe 2025 (25 mm OD) pipe 2532 (32 mm OD) pipe metre metre metre metre 297.95 340.60 405.65 507.30
18.3
Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work 18.3.1 18.3.2 1216 (16 mm OD) pipe 1620 (20 mm OD ) pipe metre metre 181.15 212.85
311
Code No.
Description 18.3.3 18.3.4 18.3.5 18.3.6 2025 (25 mm OD ) pipe 2532 (32 mm OD ) pipe 3240 (40 mm OD ) pipe 4050 (50 mm OD ) pipe
PP- R PIPES 18.4 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.4.1 18.4.2 18.4.3 18.4.4 18.4.5 18.4.6 18.5 PN - 16 Pipe, 16 mm OD PN - 16 Pipe, 20 mm OD PN - 16 Pipe, 25 mm OD PN - 16 Pipe, 32 mm OD PN - 16 Pipe, 40 mm OD PN - 16 Pipe, 50 mm OD metre metre metre metre metre metre 100.20 132.45 176.80 258.70 387.55 523.45
Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc., 18.5.1 18.5.2 18.5.3 18.5.4 PN - 16 Pipe, 16 mm OD PN - 16 Pipe, 20 mm OD PN - 16 Pipe, 25 mm OD PN - 16 Pipe, 32 mm OD metre metre metre metre 180.05 216.65 269.50 367.05
18.6
Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 18.6.1 18.6.2 18.6.3 18.6.4 PN - 16 Pipe, 16 mm OD (SDR - 7.4) PN - 16 Pipe, 20 mm OD (SDR - 7.4) PN - 16 Pipe, 25 mm OD (SDR - 7.4) PN - 16 Pipe, 32 mm OD (SDR - 7.4) metre metre metre metre 93.60 120.75 164.00 236.45
312
Code No.
Description 18.6.5 18.6.6 18.6.7 18.6.8 18.6.9 18.6.10 18.6.11 PN - 16 Pipe, 40 mm OD (SDR - 7.4) PN - 16 Pipe, 50 mm OD (SDR - 7.4) PN - 16 Pipe, 63 mm OD (SDR - 7.4) PN - 16 Pipe, 75 mm OD (SDR - 7.4) PN - 16 Pipe, 90 mm OD (SDR - 7.4) PN - 10 Pipe, 110 mm OD (SDR - 11) PN - 10 Pipe, 160 mm OD (SDR - 11)
C.P.V.C. PIPES 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.1 18.7.2 18.7.3 18.7.4 18.7.5 18.7.6 18.8 15 mm nominal outer dia Pipes 20 mm nominal outer dia Pipes 25 mm nominal outer dia Pipes 32 mm nominal outer dia Pipes 40 mm nominal outer dia Pipes 50 mm nominal outer dia Pipes metre metre metre metre metre metre 133.95 157.15 197.90 252.65 348.25 514.35
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 18.8.1 18.8.2 18.8.3 18.8.4 15 mm nominal outer dia Pipes 20 mm nominal outer dia Pipes 25 mm nominal outer dia Pipes 32 mm nominal outer dia Pipes metre metre metre metre 218.65 243.05 297.95 358.90
18.9
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 18.9.1 18.9.2 15 mm nominal outer dia Pipes 20 mm nominal outer dia Pipes metre metre 122.25 140.40
313
Code No.
Description 18.9.3 18.9.4 18.9.5 18.9.6 18.9.7 18.9.8 18.9.9 18.9.10 25 mm nominal outer dia Pipes 32 mm nominal outer dia Pipes 40 mm nominal outer dia Pipes 50 mm nominal outer dia Pipes 62.50 mm nominal inner dia Pipes 75 mm nominal inner dia Pipes 100 mm nominal inner dia Pipes 150 mm nominal inner dia Pipes
18.10
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 18.10.1 18.10.2 18.10.3 18.10.4 18.10.5 18.10.6 15 mm dia nominal bore 20 mm dia nominal bore 25 mm dia nominal bore 32 mm dia nominal bore 40 mm dia nominal bore 50 mm dia nominal bore metre metre metre metre metre metre 161.60 188.05 243.15 296.50 364.10 453.65
18.11
Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 18.11.1 18.11.2 15 mm dia nominal bore 20 mm dia nominal bore metre metre 229.10 251.30
18.12
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 18.12.1 18.12.2 18.12.3 18.12.4 18.12.5 18.12.6 18.12.7 18.12.8 15 mm dia nominal bore 20 mm dia nominal bore 25 mm dia nominal bore 32 mm dia nominal bore 40 mm dia nominal bore 50 mm dia nominal bore 65 mm dia nominal bore 80 mm dia nominal bore metre metre metre metre metre metre metre metre 142.25 161.25 209.40 248.55 294.20 355.95 453.55 573.40
18.13
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 18.13.1 18.13.2 25 to 40 mm nominal bore 50 to 80 mm nominal bore each each 277.35 630.15
314
Description Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). BRASS FITTINGS
Unit
Rate
each
228.55
18.15
Providing and fixing brass bib cock of approved quality : 18.15.1 18.15.2 15 mm nominal bore 20 mm nominal bore each each 205.60 266.15
18.16
Providing and fixing brass stop cock of approved quality : 18.16.1 18.16.2 15 mm nominal bore 20 mm nominal bore each each 205.60 266.65
18.17
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.17.1 18.17.2 18.17.3 18.17.4 18.17.5 18.17.6 25 mm nominal bore 32 mm nominal bore. 40 mm nominal bore 50 mm nominal bore 65 mm nominal bore 80 mm nominal bore each each each each each each 372.95 450.90 546.05 780.60 1,073.25 1,832.95
18.18
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 18.18.1 18.18.2 18.18.3 15 mm nominal bore 20 mm nominal bore 25 mm nominal bore each each each 258.05 360.20 421.65
18.19
Providing and fixing gun metal non- return valve of approved quality (screwed end) : 18.19.1 18.19.1.1 18.19.1.2 18.19.2 18.19.2.1 18.19.2.2 18.19.3 18.19.3.1 18.19.3.2 18.19.4 18.19.4.1 18.19.4.2 25 mm nominal bore Horizontal Vertical 32 mm nominal bore Horizontal Vertical 40 mm nominal bore Horizontal Vertical 50 mm nominal bore Horizontal Vertical each each 936.35 1,110.55 each each 620.25 817.70 each each 490.25 594.80 each each 383.45 395.05
315
Code No.
Description 18.19.5 18.19.5.1 18.19.5.2 18.19.6 18.19.6.1 18.19.6.2 65 mm nominal bore Horizontal Vertical 80 mm nominal bore Horizontal Vertical
Unit
Rate
18.20
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 18.20.1 18.20.2 18.20.3 15 mm nominal bore 20 mm nominal bore 25 mm nominal bore each each each 203.30 250.10 331.25
18.21
Providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.1 18.21.1.1 18.21.1.2 18.21.2 18.21.2.1 18.21.2.2 30 cm length 15 mm nominal bore 20 mm nominal bore 45 cm length 15 mm nominal bore 20 mm nominal bore 100 mm diameter 150 mm diameter each each each each 61.70 73.35 58.15 77.85 each each 51.35 59.50
18.22
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 18.22.1 18.22.2
C.I/ DUCTILE IRON PIPES & SPECIALS 18.23 18.24 18.25 Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe). Laying in position S&S or flanged C.I. special such as tees, bends, collars, tapers and caps etc.(excluding cost of specials). Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class) : 18.25.1 18.25.2 18.26 Up to 300 mm dia Over 300 mm dia quintal quintal 4,202.35 4,318.50 quintal quintal 101.70 186.10
Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 : 18.26.1 18.26.2 Up to 300 mm dia Over 300 mm dia quintal quintal 6,351.10 6,699.55
18.27
Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 18.27.1 18.27.2 100 mm dia pipe 125 mm dia pipe metre metre 986.40 1,237.15
316
Code No.
Description 18.27.3 18.27.4 18.27.5 18.27.6 18.27.7 18.27.8 18.27.9 18.27.10 18.27.11 150 mm dia pipe 200 mm dia pipe 250 mm dia pipe 300 mm dia pipe 350 mm dia pipe 400 mm dia pipe 450 mm dia pipe 500 mm dia pipe 600 mm dia pipe
Unit metre metre metre metre metre metre metre metre metre
Rate 1,476.70 2,516.30 3,360.20 4,437.80 5,346.45 6,965.85 8,425.25 9,787.20 13,576.25
18.28
Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 18.28.1 18.28.2 18.28.3 18.28.4 18.28.5 18.28.6 18.28.7 18.28.8 18.28.9 18.28.10 18.28.11 100 mm diameter pipe 125 mm diameter pipe 150 mm diameter pipe 200 mm diameter pipe 250 mm diameter pipe 300 mm diameter pipe 350 mm diameter pipe 400 mm diameter pipe 450 mm diameter pipe 500 mm diameter pipe 600 mm diameter pipe each each each each each each each each each each each quintal 150.00 220.65 225.10 298.65 372.70 448.75 463.85 604.35 676.85 716.75 965.35 10,462.55
18.29 18.30
Supplying pig lead at site of work. Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints : 18.30.1 18.30.2 18.30.3 18.30.4 18.30.5 18.30.6 18.30.7 18.30.8 18.30.9 18.30.10 18.30.11 18.30.12 80 mm diameter pipe 100 mm diameter pipe 125 mm diameter pipe 150 mm diameter pipe 200 mm diameter pipe 250 mm diameter pipe 300 mm diameter pipe 350 mm diameter pipe 400 mm diameter pipe 450 mm diameter pipe 500 mm diameter pipe 600 mm diameter pipe
each each each each each each each each each each each each
92.65 155.25 165.70 192.80 198.65 297.20 306.50 408.30 657.35 814.95 893.15 1,059.15
317
Code No.
Unit
Rate
18.31
Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 18.31.1 18.31.1.1 18.31.1.2 18.31.2 18.31.2.1 18.31.2.2 18.31.3 18.31.3.1 18.31.3.2 18.31.4 18.31.4.1 18.31.4.2 18.31.5 18.31.5.1 18.31.5.2 18.31.6 18.31.6.1 18.31.6.2 100 mm diameter Class I Class II 125 mm diameter Class I Class II 150 mm diameter Class I Class II 200 mm diameter Class I Class II 250 mm diameter Class I Class II 300 mm diameter Class I Class II each each 16,766.25 20,950.60 each each 12,037.80 16,723.30 each each 8,242.25 11,260.60 each each 4,487.75 5,200.40 each each 3,461.15 4,181.45 each each 3,068.35 3,498.30
18.32
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 908.95
18.33
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 5,392.90
318
Description Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.34.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Unit
Rate
each
9,277.10
18.35
Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.35.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 12,866.45
18.36
Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.36.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 5,106.65
18.37
Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.37.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 each 4,925.60
319
Description Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 18.38.1 18.38.2 18.38.3 18.38.4 18.38.5 18.38.6 15 mm diameter pipe 20 mm diameter pipe 25 mm diameter pipe 32 mm diameter pipe 40 mm diameter pipe 50 mm diameter pipe
Unit
Rate
18.39
Repainting G.I. pipes and fittings with synthetic enamel white paint with one coat of approved quality : 18.39.1 18.39.2 18.39.3 18.39.4 18.39.5 18.39.6 15 mm diameter pipe 20 mm diameter pipe 25 mm diameter pipe 32 mm diameter pipe 40 mm diameter pipe 50 mm diameter pipe metre metre metre metre metre metre 3.75 4.35 5.60 6.60 7.70 9.00
18.40
Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 18.40.1 18.40.2 18.40.3 18.40.4 18.40.5 18.40.6 18.40.7 18.40.8 15 mm diameter pipe 20 mm diameter pipe 25 mm diameter pipe 32 mm diameter pipe 40 mm diameter pipe 50 mm diameter pipe 65 mm diameter pipe 80 mm diameter pipe metre metre metre metre metre metre metre metre 4.40 5.15 6.60 7.80 8.90 10.55 12.95 15.00
18.41
Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 18.41.1 18.41.2 18.41.3 18.41.4 18.41.5 18.41.6 18.41.7 18.41.8 18.41.9 15 mm diameter pipe 20 mm diameter pipe 25 mm diameter pipe 32 mm diameter pipe 40 mm diameter pipe 50 mm diameter pipe 65 mm diameter pipe 80 mm diameter pipe 100 mm diameter pipe metre metre metre metre metre metre metre metre metre metre 54.75 55.50 56.95 58.45 59.20 61.40 96.95 99.90 105.80 157.60
320
Description Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested : 18.42.1 18.42.2 18.42.3 Up to 6 metres depth Beyond 6 m and up to 12 m depth Beyond 12 m and up to 18 m depth
Unit
Rate
Providing and placing in position filters of 40 mm diameter G.I. pipe with brass strainer of approved quality. Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe for tube well including cleaning and priming the tube well. Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories. Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 18.46.1 18.46.2 18.46.3 18.46.4 18.46.5 18.46.6 18.46.7 18.46.8 15 mm nominal bore 20 mm nominal bore 25 mm nominal bore 32 mm nominal bore 40 mm nominal bore 50 mm nominal bore 65 mm nominal bore 80 mm nominal bore
18.47
Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 18.47.1 18.47.2 18.47.3 18.47.4 18.47.5 18.47.6 18.47.7 18.47.8 15 mm nominal bore 20 mm nominal bore 25 mm nominal bore 32 mm nominal bore 40 mm nominal bore 50 mm nominal bore 65 mm nominal bore 80 mm nominal bore each each each each each each each each 259.65 282.90 294.50 329.35 370.00 498.65 742.55 847.10
18.48
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. C.P. BRASS F ITTINGS Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 18.49.1 15 mm nominal bore
per litre
6.10
18.49
each
397.50
321
Description Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1 15 mm nominal bore
Unit
Rate
each
411.40
18.51
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 18.51.1 15 mm nominal bore each 430.60 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1 15 mm nominal bore each 426.55 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 18.53.1 15mm nominal bore each 449.35 PTMT FITTINGS
18.52
18.53
18.54
Providing and fixing PTMT bib cock of approved quality and colour. 18.54.1 18.54.2 18.54.3 18.54.4 15mm nominal bore, 86 mm long, weighing not less than 88 gms 15 mm nominal bore, 122mm long, weighing not less than 99 gms 15 mm nominal bore, 165 mm long, weighing not less than 110 gms 15mm nominal bore, 90 mm long, weighing not less than 93 gms 15 mm nominal bore, 86 mm long, weighing not less than 88 gms 20 mm nominal bore, 89 mm long, weighing not less than 88 gms Concealed stop cock, 15 mm nominal bore, 108 mm long, weighing not less than 108 gms 15 mm nominal bore, 107 mm long, weighing not less than 110 gms 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms 15 mm nominal bore, 98 mm long, weighing not less than 75 gms 15 mm nominal bore, 80 mm long, weighing not less than 46 gms Circular type each each each each 130.10 176.55 199.80 168.45
18.55
Providing and fixing PTMT stop cock of approved quality and colour. 18.55.1 18.55.2 18.55.3 each each each 130.10 164.95 214.90
18.56
Providing and fixing PTMT pillar cock of approved quality and colour . 18.56.1 18.56.2 each each 202.25 277.25
18.57
Providing and fixing PTMT, push cock of approved quality and colour. 18.57.1 18.57.2 each each 118.50 106.85
18.58
Providing and fixing PTMT grating of approved quality and colour. 18.58.1
322
Code No.
Description 18.58.1.1 18.58.1.2 18.58.2 18.58.2.1 100 mm nominal dia 125 mm nominal dia with 25 mm waste hole Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating
each
124.50
AIR VALVE & WATER METER (BULK TYPE) 18.59 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 18.59.1 18.59.2 18.59.3 18.60 50 mm dia 80 mm dia 100 mm dia each each each 4,018.15 5,830.10 7,602.35
Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 18.60.1 18.60.2 18.60.3 18.60.4 80 mm dia nominal bore 100 mm dia nominal bore 150 mm dia nominal bore 200 mm dia nominal bore each each each each 2,880.60 4,329.20 6,132.00 6,860.90
18.61
Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : 18.61.1 18.61.2 18.61.3 18.61.4 80 mm dia 100 mm dia 150 mm dia 200 mm dia each each each each 3,340.90 5,300.55 6,860.90 9,436.60
18.62
Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 18.62.1 18.62.2 18.62.3 18.62.4 18.62.5 15 mm nominal bore, 105 mm long, weighing not less than 138 gms 20 mm nominal bore, 120 mm long, weighing not less than 198 gms 25 mm nominal bore, 152mm long, weighing not less than 440 gms 40 mm nominal bore, 206mm long, weighing not less than 690 gms 50 mm nominal bore, 242mm long, weighing not less than 1240 gms each each each each each each 193.00 273.05 543.65 961.75 1,391.50 164.95
18.63
Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms
323
Description Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. Providing and laying S&S C.I. Standard specials such as tees, bends, collars tapers and caps etc, suitable for flanged jointing as per IS : 1538 : 18.66.1 18.66.2 Up to 300 mm dia Above 300 mm dia
Unit
Rate
each
112.75
each
151.10
18.66
quintal quintal
6,989.95 8,906.40
18.67
Providing and laying S&S C.I. Standard specials suitable for mechanical jointing as per IS : 13382 : 18.67.1 18.67.2 Up to 300 mm dia Above 300 mm dia quintal quintal 9,719.45 10,509.25
18.68
Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523 : 18.68.1 18.68.2 Up to 600 mm dia Above 600 mm dia quintal quintal 13,958.95 19,104.40
18.69
Providing and laying D.I. Specials of Class K - 12 suitable for mechanical jointing as per IS : 9523 : 18.69.1 18.69.2 Up to 600 mm dia Above 600 mm dia quintal quintal 14,760.35 20,614.30
18.70
Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket : 18.70.1 18.70.2 18.70.3 18.70.4 18.70.5 18.70.6 18.70.7 18.70.8 18.70.9 18.70.11 100 mm dia pipes 150 mm dia pipes 200 mm dia pipes 250 mm dia pipes 300 mm dia pipes 350 mm dia pipes 400 mm dia pipes 450 mm dia pipes 500 mm dia pipes 650 mm dia pipes joint joint joint joint joint joint joint joint joint joint joint joint joint joint joint 49.25 79.05 121.65 146.80 194.05 221.95 317.05 413.65 448.85 570.10 820.55 929.75 1,005.35 1,310.85 1,594.70
18.70.10 600 mm dia pipes 18.70.12 700 mm dia pipes 18.70.13 800 mm dia pipes 18.70.14 900 mm dia pipes 18.70.15 1000 mm dia pipes
SUBHEAD -18.0 WATER SUPPLY
324
Description Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 18.71.1 18.71.2 18.71.3 18.71.4 18.71.5 18.71.6 18.71.7 18.71.8 18.71.9 100 mm dia C.I. Double Flanged Pipe 150 mm dia C.I. Double Flanged Pipe 200 mm dia C.I. Double Flanged Pipe 250 mm dia C.I. Double Flanged Pipe 300 mm dia C.I. Double Flanged Pipe 350 mm dia C.I. Double Flanged Pipe 400 mm dia C.I. Double Flanged Pipe 450 mm dia C.I. Double Flanged Pipe 500 mm dia C.I. Double Flanged Pipe
Unit
Rate
metre metre metre metre metre metre metre metre metre metre
1,493.15 2,325.20 3,752.65 4,427.80 5,662.80 7,214.85 9,354.10 11,775.05 14,654.50 18,163.60
18.71.10 600 mm dia C.I. Double Flanged Pipe 18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : 18.72.1 18.72.2 18.72.3 18.72.4 18.72.5 18.72.6 18.72.7 18.72.8 18.72.9 18.72.11 100 mm dia Ductile Iron Class K-7 pipes 150 mm dia Ductile Iron Class K-7 pipes 200 mm dia Ductile Iron Class K-7 pipes 250 mm dia Ductile Iron Class K-7 pipes 300 mm dia Ductile Iron Class K-7 pipes 350 mm dia Ductile Iron Class K-7 pipes 400 mm dia Ductile Iron Class K-7 pipes 450 mm dia Ductile Iron Class K-7 pipes 500 mm dia Ductile Iron Class K-7 pipes 700 mm dia Ductile Iron Class K-7 pipes
metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre metre
840.25 1,229.05 1,680.15 2,278.60 3,123.85 3,723.25 4,413.65 5,241.05 6,189.20 8,077.40 10,379.50 13,242.40 17,320.75 18,414.10 946.00 1,389.40 1,895.40 2,502.35 3,184.95 3,841.75 5,169.15 6,043.80 7,334.45 8,838.45
18.72.10 600 mm dia Ductile Iron Class K-7 pipes 18.72.12 800 mm dia Ductile Iron Class K-7 pipes 18.72.13 900 mm dia Ductile Iron Class K-7 pipes 18.72.14 1000 mm dia Ductile Iron Class K-7 pipes 18.72.15 100 mm dia Ductile Iron Class K-9 pipes 18.72.16 150 mm dia Ductile Iron Class K-9 pipes 18.72.17 200 mm dia Ductile Iron Class K-9 pipes 18.72.18 250 mm dia Ductile Iron Class K-9 pipes 18.72.19 300 mm dia Ductile Iron Class K-9 pipes 18.72.20 350 mm dia Ductile Iron Class K-9 pipes 18.72.21 400 mm dia Ductile Iron Class K-9 pipes 18.72.22 450 mm dia Ductile Iron Class K-9 pipes 18.72.23 500 mm dia Ductile Iron Class K-9 pipes 18.72.24 600 mm dia Ductile Iron Class K-9 pipes
SUBHEAD -18.0 WATER SUPPLY
325
Code No.
Description 18.72.25 700 mm dia Ductile Iron Class K-9 pipes 18.72.26 750 mm dia Ductile Iron Class K-9 pipes 18.72.27 800 mm dia Ductile Iron Class K-9 pipes 18.72.28 900 mm dia Ductile Iron Class K-9 pipes 18.72.29 1000 mm dia Ductile Iron Class K-9 pipes
18.73
Providing and laying Double Flanged (Screwed / Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 : 18.73.1 18.73.2 18.73.3 18.73.4 18.73.5 18.73.6 18.73.7 18.73.8 18.73.9 18.73.11 100 mm dia Ductile Iron Double Flanged 150 mm dia Ductile Iron Double Flanged 200 mm dia Ductile Iron Double Flanged 250 mm dia Ductile Iron Double Flanged 300 mm dia Ductile Iron Double Flanged 350 mm dia Ductile Iron Double Flanged 400 mm dia Ductile Iron Double Flanged 450 mm dia Ductile Iron Double Flanged 500 mm dia Ductile Iron Double Flanged 700 mm dia Ductile Iron Double Flanged metre metre metre metre metre metre metre metre metre metre metre 2,376.45 3,318.10 4,395.00 5,801.00 7,440.60 9,423.00 11,332.70 13,715.20 16,314.30 22,029.20 27,318.00
18.73.10 600 mm dia Ductile Iron Double Flanged 18.74 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 18.74.1 18.74.2 18.75 15 mm nominal bore with 30cm length 15 mm nominal bore with 45 cm length
each each
59.50 67.55
Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 18.75.1 18.75.2 18.75.3 15 mm nominal bore, weighing not less than 32 gms 20mm nominal bore, weighing not less than 40 gms 25mm nominal bore, weighing not less than 62 gms each each each 43.00 50.00 72.05
18.76
Cutting holes up to 30x30 cm in walls including making good the same: 18.76.1 With common burnt clay F.P.S. (non modular) bricks each 152.00 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.
18.77
each metre
143.95 63.60
18.78 18.79
metre
102.80
326
Description Disinfecting C.I. water mains by flushing with water containing bleaching powder @ 0.5 gms per litre of water and cleaning the same with fresh water, operation to be repeated three times including getting the sample of water from the disinfected main tested in the municipal laboratory. 18.80.1 18.80.2 18.80.3 18.80.4 18.80.5 18.80.6 18.80.7 18.80.8 18.80.9 18.80.11 80 mm diameter C.I. pipe 100 mm diameter C.I. pipe 125 mm diameter C.I. pipe 150 mm diameter C.I. pipe 200 mm diameter C.I. pipe 250 mm diameter C.I. pipe 300 mm diameter C.I. pipe 350 mm diameter C.I. pipe 400 mm diameter C.I. pipe 500 mm diameter C.I. pipe
Unit
Rate
100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre
524.55 689.60 863.55 1,041.00 1,398.35 1,773.25 1,996.10 2,230.70 2,482.85 2,742.75 3,020.15 3,596.85
18.80.10 450 mm diameter C.I. pipe 18.80.12 600 mm diameter C.I. pipe 18.81 Extra for every operation of disinfecting the C.I. main by flushing with water containing bleaching powder @ 0.5 gms per litre of water and cleaning the same with fresh water, including getting the samples of water tested in the municipal laboratory : 18.81.1 18.81.2 18.81.3 18.81.4 18.81.5 18.81.6 18.81.7 18.81.8 18.81.9 18.81.11 18.82 80 mm diameter C.I. pipe 100 mm diameter C.I. pipe 125 mm diameter C.I. pipe 150 mm diameter C.I. pipe 200 mm diameter C.I. pipe 250 mm diameter C.I. pipe 300 mm diameter C.I. pipe 350 mm diameter C.I. pipe 400 mm diameter C.I. pipe 500 mm diameter C.I. pipe
100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre
192.80 235.25 287.90 337.35 510.60 594.86 677.25 800.55 926.50 1,058.15 1,191.55 1,468.35
18.81.10 450 mm diameter C.I. pipe 18.81.12 600 mm diameter C.I. pipe Dismantling old C.I. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 metre : 18.82.1 18.82.2 18.82.3 80 mm diameter C.I. pipe 100 mm diameter C.I. pipe 125 mm diameter C.I. pipe
327
Code No.
Description 18.82.4 18.82.5 18.82.6 18.82.7 18.82.8 18.82.9 18.82.11 150 mm diameter C.I. pipe 200 mm diameter C.I. pipe 250 mm diameter C.I. pipe 300 mm diameter C.I. pipe 350 mm diameter C.I. pipe 400 mm diameter C.I. pipe 500 mm diameter C.I. pipe
Unit metre metre metre metre metre metre metre metre metre Each cut Each cut Each cut Each cut Each cut Each cut Each cut Each cut Each cut Each cut Each cut Each cut
Rate 164.60 181.90 198.65 213.10 226.35 238.15 250.40 260.65 277.65 41.35 55.65 77.65 104.70 139.65 173.10 208.05 241.45 276.20 309.80 344.55 409.80
18.82.10 450 mm diameter C.I. pipe 18.82.12 600 mm diameter C.I. pipe 18.83 Labour for cutting C.I. pipe with steel saw. 18.83.1 18.83.2 18.83.3 18.83.4 18.83.5 18.83.6 18.83.7 18.83.8 18.83.9 18.83.11 NEW ITEMS 18.84 Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 18.84.1 15 mm nominal bore 80 mm diameter C.I. pipe 100 mm diameter C.I. pipe 125 mm diameter C.I. pipe 150 mm diameter C.I. pipe 200 mm diameter C.I. pipe 250 mm diameter C.I. pipe 300 mm diameter C.I. pipe 350 mm diameter C.I. pipe 400 mm diameter C.I. pipe 500 mm diameter C.I. pipe
18.83.10 450 mm diameter C.I. pipe 18.83.12 600 mm diameter C.I. pipe
each
6,776.80
328
DRAINAGE
329
331
Code No. 1701 1702 1703 1704 1705 1706 1707 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1723 1724 1725 1726 1727 1854 1855 1856 1858 1859 1881 1900
Description R.C.C. pipes NP2 class 150 mm dia R.C.C. pipes NP2 class 250 mm dia R.C.C. pipes NP2 class 300 mm dia R.C.C. pipes NP2 class 450 mm dia R.C.C. pipes NP2 class 500 mm dia R.C.C. pipes NP2 class 600 mm dia R.C.C. pipes NP2 class 700 mm dia R.C.C. pipes NP2 class 800 mm dia R.C.C. pipes NP2 class 900 mm dia R.C.C. pipes NP2 class 1000 mm dia R.C.C. pipes NP2 class 1100 mm dia R.C.C. pipes NP2 class 1200 mm dia R.C.C. collars NP2 class 100 mm dia R.C.C. collars NP2 class 150 mm dia R.C.C. collars NP2 class 250 mm dia R.C.C. collars NP2 class 300 mm dia R.C.C. collars NP2 class 450 mm dia R.C.C. collars NP2 class 500 mm dia R.C.C. collars NP2 class 600 mm dia R.C.C. collars NP2 class 700 mm dia R.C.C. collars NP2 class 800 mm dia R.C.C. collars NP2 class 900 mm dia R.C.C. collars NP2 class 1000 mm dia R.C.C. collars NP2 class 1100 mm dia R.C.C. collars NP2 class 1200 mm dia Stoneware pipes grade A (60 cm long) 100 mm dia Stoneware pipes grade A (60 cm long) 150 mm dia Stoneware pipes grade A (60 cm long) 200 mm dia Stoneware pipes grade A (60 cm long) 250 mm dia Stoneware pipes grade A (60 cm long) 300 mm dia Spun yarn S.W. gully trap P type 100x100 mm
Unit metre metre metre metre metre metre metre metre metre metre metre metre each each each each each each each each each each each each each each each each each each kilogram each
Rate 154.00 188.00 261.00 380.00 454.00 732.00 850.00 960.00 1,125.00 1,420.00 1,730.00 1,760.00 20.00 25.00 40.00 49.00 75.00 89.00 109.00 121.00 172.00 210.00 256.00 283.00 330.00 36.00 53.00 91.00 130.00 190.00 40.00 70.00
332
Code No. 1902 1904 2201 2209 2224 2225 2226 2228 2229 2260 2261 2275 2281 2287 2290 2299 2303 2331 2332 2333 2334 2602 3860 3861 7087 7128 7129 7130 7131 7132
Description S.W. gully trap P type 150x100 mm S.W. gully trap P type 180x150 mm Carriage of Bricks Carriage of Cement Carriage of S.W. pipes 100 mm dia Carriage of S.W. pipes 150 mm dia Carriage of S.W. pipes 200 mm dia Carriage of S.W. pipes 250 mm dia Carriage of S.W. pipes 300 mm dia Carriage of Brick aggregate Carriage of Fine sand (1 part badarpur sand : 2 parts jamuna sand) Carriage of R.C.C. pipes 100 mm dia Carriage of R.C.C. pipes 150 mm dia Carriage of R.C.C. pipes 250 mm dia Carriage of R.C.C. pipes 300 mm dia Carriage of R.C.C. pipes 450 & 500 mm dia Carriage of R.C.C. pipes 600, 700, 750 & 800 mm dia Carriage of R.C.C. pipes 900 mm dia Carriage of R.C.C. pipes 1000 mm dia Carriage of R.C.C. pipes 1100 mm dia Carriage of R.C.C. pipes 1200 mm dia Common burnt clay F.P.S. (non modular) bricks class designation 7.5 560 mm dia cover with frame (Heavy duty) 560 mm dia cover without frame (Heavy duty) S.C.I. Tee 150 mm S.W. intercepting trap 100 mm dia S.W. intercepting trap 150 mm dia Rectangular shape 600x450 mm precast R.C.C. manhole cover with frame - L.D. - 25 Square shape 450x450 mm precast R.C.C. manhole cover with frame - L.D. - 25 Circular shape 450 mm dia precast R.C.C. manhole cover with frame - L.D. - 25
Unit each each 1,000 nos tonne 100 metre 100 metre 100 metre 100 metre 100 metre cum cum 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 1,000 nos each each each each each each each each
Rate 104.00 195.00 233.60 77.87 116.80 233.60 389.33 667.43 834.29 95.22 87.60 191.48 319.12 737.68 911.78 2,127.50 3,191.25 4,786.87 6,382.50 6,382.50 6,382.50 2,900.00 8,460.00 4,500.00 505.00 170.00 225.00 690.00 600.00 560.00
333
Code No. 7133 7134 7135 7136 7354 7380 7381 9999
Description Rectangular shape 500x500 mm precast R.C.C. manhole cover with frame - M.D. - 10 Circular shape 500 mm dia precast R.C.C. manhole cover with frame - M.D. - 10 Circular shape 560 mm dia precast R.C.C. manhole cover with frame - H.D. - 20 Circular shape 560 mm dia precast R.C.C. manhole cover with frame - E.H.D. - 35 Plastic encapsulated M.S. foot rest 30x20x15 cm Precast R.C.C. grating with frame 500x450 mm horizontal grating Precast R.C.C. grating with frame 450x100 mm vertical grating Sundries
Unit
Rate
334
19.0 DRAINAGE
Code No. Description NOTE : - The rates given for all the items under sub-head ' Drainage' are applicable to work executed in soils above sub- soil water level. Extra allowance has to be made for work under sub- soil water level. STONE WARE PIPES AND FITTINGS 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 19.1.1 19.1.2 19.1.3 19.1.4 19.1.5 19.2 100 mm diameter 150 mm diameter 200 mm diameter 250 mm diameter 300 mm diameter metre metre metre metre metre 150.10 219.05 323.05 446.15 597.85 Unit Rate
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 19.2.1 19.2.2 19.2.3 19.2.4 100 mm diameter S.W. pipe 150 mm diameter S.W. pipe 200 mm diameter S.W. pipe 250 mm diameter S.W. pipe metre metre metre metre 496.90 607.70 708.40 819.20
19.3
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 19.3.1 19.3.2 19.3.3 19.3.4 19.3.5 100 mm diameter S.W. pipe 150 mm diameter S.W. pipe 200 mm diameter S.W. pipe 250 mm diameter S.W. pipe 300 mm diameter S.W. pipe metre metre metre metre metre 236.15 382.75 449.90 523.75 604.35
19.4
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 19.4.1 19.4.1.1 19.4.1.2 19.4.2 19.4.2.1 19.4.2.2 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With sewer bricks conforming to IS : 4885 each each 1,278.30 1,315.55 each each 1,256.35 1,293.60
335
Code No.
Description 19.4.3 19.4.3.1 19.4.3.2 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885
Unit
Rate
each each
1,365.55 1,402.80
19.5
Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 19.5.1 19.5.2 19.5.3 19.5.4 19.5.5 19.5.6 19.5.7 19.5.8 100 mm diameter 150 mm diameter 200 mm diameter 250 mm diameter 300 mm diameter 350 mm diameter 400 mm diameter 450 mm diameter metre metre metre metre metre metre metre metre 24.40 26.95 28.70 30.40 32.15 37.00 40.45 42.15
19.6
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 19.6.1 19.6.2 19.6.3 19.6.4 19.6.5 19.6.6 19.6.7 19.6.8 19.6.9 19.6.10 19.6.11 19.6.12 19.6.13 100 mm dia. R.C.C. pipe 150 mm dia. R.C.C. pipe 250 mm dia. R.C.C. pipe 300 mm dia. R.C.C. pipe 450 mm dia. R.C.C. pipe 500 mm dia. R.C.C. pipe 600 mm dia. R.C.C. pipe 700 mm dia. R.C.C. pipe 800 mm dia. R.C.C. pipe 900 mm dia. R.C.C. pipe 1000 mm dia. R.C.C. pipe 1100 mm dia. R.C.C. pipe 1200 mm dia. R.C.C. pipe metre metre metre metre metre metre metre metre metre metre metre metre metre 218.35 254.50 342.45 422.90 620.85 722.20 1,084.25 1,247.05 1,415.70 1,678.85 2,111.10 2,554.80 2,694.55
19.7
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal
336
Code No.
Description dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 19.7.1.2 19.7.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885 Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885 Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885 Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885 Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885
Unit
Rate
each each
7,132.00 7,229.45
each each
15,322.95 15,589.40
19.7.3.1 19.7.3.2 19.8 19.8.1 19.8.1.1 19.8.1.2 19.8.2 19.8.2.1 19.8.2.2 19.9
each each
19,778.80 20,008.05
metre metre
4,061.70 4,345.40
metre metre
4,866.75 5,204.90
Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering,
337
Code No.
Description shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : 19.9.1.1 19.9.1.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming to IS : 4885
Unit
Rate
each each
7,007.40 7,162.50
19.10
Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m 19.10.1 19.10.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming IS : 4885 metre metre 3,498.25 3,735.75
19.11
Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming IS : 4885 each each 12,943.40 13,316.30
Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : 19.12.1 19.12.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming IS : 4885 metre metre 4,522.30 4,832.30
19.13
Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not
338
Code No.
Description less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : 19.13.1.1 19.13.1.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming IS : 4885
Unit
Rate
each each
26,873.70 27,934.70
19.14
Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : 19.14.1 19.14.2 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 With Sewer bricks conforming IS : 4885 metre metre 10,643.40 11,445.10
19.15
Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : 19.15.1 19.15.2 With 20x20 mm square bar With 20 mm diameter round bar each each 227.95 193.15
19.16
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) : 19.17.1 19.17.2 With 20x20 mm square bar With 20 mm diameter round bar 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg
each
256.75
19.17
each each
262.30 227.45
19.18
Supplying and fixing C.I. cover without frame for manholes : 19.18.1 19.18.2 19.18.3 each each each 1,185.05 2,624.65 5,289.10
19.19
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5
339
Code No.
Description 19.19.1.1 19.19.1.2 19.19.1.3 19.19.2 19.19.2.1 19.19.2.2 19.19.3 19.19.3.1 19.19.4 19.19.4.1 Rectangular shape 600x450 mm internal dimensions Square shape 450 mm internal dimensions Circular shape 450 mm internal diameter M D - 10 Square shape 450 mm internal dimension Circular shape 500 mm internal diameter H D - 20 Circular shape 560 mm internal diameter EHD - 35 Circular shape 560 mm internal dia
19.20 19.21
Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 19.21.1 19.21.2 19.21.3 For pipes 100 to 250 mm diameter For pipes 250 to 300 mm diameter For pipes 350 to 450 mm diameter
19.22
Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering required, cutting holes in walls and making good with brick work in cement mortar 1:4 (1 cement : 4 coarse sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand) on inside of the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 cement : 1 fine sand) joints between sand cast iron tee and S.W. pipe, making required channels complete as per standard design and specifications : 19.22.1 19.22.2 100 mm dia sand cast iron drop connection 150 mm dia sand cast iron drop connection each each 4,700.30 6,775.45
19.23
Extra for depths beyond 60 cm of sand cast iron drop connection complete : 19.23.1 19.23.2 For 100 mm dia sand cast iron drop connection For 150 mm dia sand cast iron drop connection metre metre 1,577.20 2,167.60
19.24
Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials into municipal dumps within 50 m lead : 19.24.1 Rectangular manhole 90x80 cm and 45 cm deep each 705.60
340
Code No.
Description 19.24.2 19.24.3 19.24.4 Rectangular manhole 120x90 cm and 90 cm deep Rectangular arch type manhole 140x90 cm and 2.45 m deep Circular manhole 122 cm diameter and 1.68 m deep Rectangular manhole 90x80 cm and beyond 45 cm depth Rectangular manhole 120x90 cm and beyond 90 cm depth Rectangular arch type manhole 140x90 cm and beyond 2.45 m depth (up to 4.25 m depth) Circular manhole 122 cm diameter and beyond 1.68 m depth (up to 2.29 m depth)
19.25
19.26
Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Raising depth of manhole to be paid separately) : 19.26.1 19.26.2 19.26.3 19.26.4 Rectangular manhole 90x80 cm with rectangular cover 600x450 mm of grade LD - 2.5 Rectangular manhole 120x90 cm with circular cover 500 mm dia of grade MD - 10 Rectangular manhole 120x90 cm with circular cover 560 mm dia of grade HD - 20 Circular manhole 140 cm dia with circular cover 600 mm dia of grade EHD - 35 each each each each 1,239.70 1,942.20 1,807.75 169.75
19.27
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 3,193.50
19.28
Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design : 19.28.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 3,451.90
19.29
Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : 19.29.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 6,111.70
19.30
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38
341
Code No.
Description kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : 19.30.1 19.30.1.1 19.30.2 19.30.2.1 19.30.3 19.30.3.1 Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 For 500x700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 For 600x850 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Unit
Rate
each
3,917.65
each
4,556.55
each
5,259.10
19.31
Extra for depth beyond 45 cm of brick masonry chamber : 19.31.1 19.31.1.1 19.31.2 19.31.2.1 19.31.3 19.31.3.1
metre
2,824.45
metre
3,081.70
metre
3,589.25
19.32
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 15,228.15
19.33
Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 19.34.1 19.34.2 100 mm dia 150 mm dia
each
1,591.35
19.34
each each
248.55 337.70
342
PILE WORK
343
per test
33,200.00
7247
per test
40,300.00
7248
per test
48,500.00
7249
per test
15,000.00
7250
per test
23,000.00
7251
per test
29,500.00
345
Description Lateral load testing of single pile in accordance with IS : 2911 part -IV for determining safe allowable lateral load on pile. Up to 50 tonne capacity Lateral load testing of single pile in accordance with IS : 2911 part -IV for determining safe allowable lateral load on pile. Above 50 tonne capacity Sundries
Unit
Rate
per test
15,000.00
7253
23,500.00 1.49
9999
346
Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 20.2.1 20.2.2 20.2.3 20.2.4 20.2.5 20.2.6 20.2.7 20.2.8 20.2.9 300 mm dia piles 400 mm dia piles 450 mm dia piles 500 mm dia. piles 600 mm dia piles 750 mm dia piles 1000 mm dia piles 1200 mm dia piles 1500 mm dia piles metre metre metre metre metre metre metre metre metre 1,382.15 1,613.95 2,154.40 2,526.55 3,310.90 4,723.60 7,809.25 10,079.80 14,300.30
20.3
Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 20.3.1 20.3.2 300 mm dia piles 400 mm dia piles metre metre 2,007.05 2,383.65
347
Code No.
20.4
Extra over item No. 23.3 for providing additional bulb in under reamed piles, under specified dia meter (Only the quantity of extra bulbs are to be paid). 20.4.1 20.4.2 20.4.3 20.4.4 300mm dia piles 400mm dia piles 450 mm dia piles 550 mm dia piles each each each each 1,341.85 1,509.90 1,611.45 1,776.55
20.5
Providing, driving and installing driven Pre-cast reinforced cement concrete piles of specified diameter and length below the pile cap in M-25 cement concrete to carry safe working load not less than specified. With a central through preformed hole with M.S. black pipe of dia, 40 mm for grouting with cement sand grouting of mix 1:2 (1 cement : 2 coarse sand) under sufficient positive pressure to ensure complete filling including centring, shuttering, driving and removing the steel casing pipe and lifting casing etc. complete but excluding the cost of steel reinforcement. (Length of pile for payment shall be measured from top of the shoe to the bottom of pile cap). 20.5.1 20.5.2 20.5.3 20.5.4 20.5.5 20.5.6 400 mm dia piles 450 mm dia piles 500 mm dia piles 550 mm dia piles 750 mm dia piles 1000 mm dia piles metre metre metre metre metre metre 2,172.30 2,562.40 2,724.50 3,007.90 5,436.20 7,315.50
20.6
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. 20.6.1 20.6.1.1 20.6.1.2 20.6.2 20.6.2.1 20.6.2.2 20.6.3 20.6.3.1 20.6.3.2 Single pile upto 50 tonne capacity Initial test Routine test Single pile above 50 tonne and upto 100 tonne capacity Initial test Routine test Group of two or more piles upto 50 tonne capacity Initial test Routine test per test per test 56,332.80 34,264.20 per test per test 46,808.45 26,714.50 per test per test 38,561.80 17,422.50
20.7
Cyclic vertical load testing of pile in accordance with IS Code of practice IS: 2911 (part IV) including preparation of pile head etc for. 20.7.1 20.7.1.1 Single pile Upto 50 tonne capacity pile per test 17,422.50
348
Code No.
Description 20.7.1.2 20.7.2 20.7.2.1 Above 50 tonne and upto 100 tonne capacity pile Group of two piles Upto 50 tonne capacity each
20.8
Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile : 20.8.1 20.8.2 Upto 50 tonne capacity pile Above 50 tonne and upto 100 tonne capacity pile per test per test 17,422.50 27,295.20
NEW ITEMS 20.9 Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge. Note :- The inclusion of the above item in the schedule of work shall be judiciously decided by the technical sanctioning authority, keeping in view the quality control, type of soil strata & importance of the project.
per test
696.90
349
ALUMINIUM WORK
351
353
Description Double action hydraulic floor spring with brass cover plate Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade) 12 mm thick Prelaminated particle board with both sides decorative lamination, flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS : 12823 (exterior grade)12 mm thick Silicon sealant Stainless steal screws 30 mm x 4 mm Hermetically sealed double glazed unit made with 6 mm thick clear float glass both side having 12 mm air gap. Stainless steel (SS 304 grade) adjustable friction window stay 205 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay 255 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay 355 x19 mm Stainless steel (SS 304 grade) adjustable friction window stay 510 x 19 mm Stainless steel (SS 304 grade) adjustable friction window stay 710 x 19 mm Masking tape Aluminium casement window fastener (Anodised AC 15 ) Aluminium casement window fastener (powder coated ) Aluminium casement window fastener (polyester powder coated) Aluminium round shape handle (anodised AC 15) Aluminium round shape handle (powder coated) Aluminium round shape handle (polyester powder coated) Stainless steel screws 25 mm x 4 mm Sundries NEW CODES
Unit each
Rate 1,675.00
sqm
690.00
7480
sqm cartridge 100 nos sqm each each each each each metre each each each each each each cent L.S.
720.00 307.00 29.00 2,290.00 168.00 189.00 236.00 437.00 793.00 1.55 40.00 41.00 42.00 49.00 54.00 59.00 32.00 1.49
8646 8647 8648 8649 8650 8651 8652 8653 8654 8660 8661 8662 8663 8664 8665 8666 9999
Aluminium Grill Stainless steel dash fastener of 8 mm dia and 75 mm long bolt Toughened glass 12 mm thickness Float glass sheet of nominal thickness 8 mm (weight not less than 20.00 kg/ sqm)
354
kg kg kg
21.1.2.1
kg kg kg
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 21.2.1 21.2.2 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side Pre-laminated particle board with decorative lamination on both sides sqm sqm 933.40 969.95
21.3
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket
355
Code No.
Description etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 21.3.2 21.3.3 With float glass panes of 4.0 mm thickness With float glass panes of 5.50 mm thickness With float glass panes of 8 mm thickness
Unit
Rate
21.4
Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. 21.4.1 21.4.2 With stainless steel cover plate minimum 1.25 mm thickness With brass cover plate minimum 1.25 mm thickness each each 1,953.10 2,127.30
21.5
Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-incharge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer -in-charge. Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge. 21.7.1 Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron)
kg
465.45
21.6
each
100.70
21.7
kg kg
447.05 476.35
21.7.2
356
Description Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 21.8.1 Upto 5mm depth and 5 mm width
Unit
Rate
metre
75.10
21.9
Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections. 21.9.1 21.9.2 For fixed portion For shutters of doors, windows & ventilators kg kg 11.60 11.60
21.10
Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete. Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin-charge complete. 21.11.1 21.11.2 21.11.3 21.11.4 21.11.5 205 X 19 mm 255 X 19 mm 355 X 19 mm 510 X 19 mm 710 X 19 mm
sqm
3,328.40
21.11
21.12
Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. 21.12.1 21.12.2 21.12.3 Anodized (AC 15 ) aluminium tubular handle bar Powder coated minimum thickness 50 micron aluminium tubular handle bar Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar each each each 498.85 544.40 555.80
21.13
Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately). Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete. 21.15.1 Anodized (AC 15) aluminium
each
356.10
21.14
kg
332.30
21.15
each
50.50
357
Code No.
Description 21.15.2 21.15.3 Powder coated minimum thickness 50 micron aluminium Polyester powder coated minimum thickness 50 micron aluminium
21.16
Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineerin-charge 21.16.1 21.16.2 21.16.3 Anodized (AC 15 ) aluminium Powder coated minimum thickness 50 micron aluminium Polyester powder coated minimum thickness 50 micron aluminium each each each 60.95 66.80 72.60
NEW ITEMS 21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
kg
388.40
21.18
sqm
4,444.75
358
WATER PROOFING
359
361
Code No. 2211 2216 2260 3002 7233 7427 7428 7429 8200 8201 8203 8204 8205 8206 8207 8501 8502 9999
Description Carriage of Tar bitumen Carriage of Stone blocks white & red sand stone & kota stone slab Carriage of Brick aggregate Polyvinyl chloride sheet 400 micron thick Fibre glass tissue reinforcement Type II Grade I Water stops Serrated with central bulb (225 mm wide, 8-11 mm thick) Water stops Dumb bell with central bulb Kickers A.P.P. modified polymeric felt (two layers) 1.5 mm thick A.P.P. modified polymeric felt (two layers) 2 mm thick A.P.P. modified 2 mm thick membrane reinforced with glass fibre matt A.P.P. modified 3 mm thick membrane reinforced with glass fibre matt A.P.P. modified 3 mm thick membrane reinforced with polyester matt Bitumen primer for bitumen membrane Geotextile 120 gsm membrane Polymer modified cementation coating Fibre glass cloth Sundries
Unit tonne tonne cum sqm sqm metre metre metre sqm sqm sqm sqm sqm litre sqm kilogram sqm L.S.
Rate 87.60 77.87 95.22 31.00 65.00 390.00 351.00 360.00 59.00 99.00 167.00 207.00 245.00 71.00 32.00 127.00 39.00 1.49
362
Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : 22.2.1 Using rough Kota stone sqm 884.90
22.3
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
(ii)
(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
sqm
399.60
22.4
Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between
363
Code No.
Description two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : 22.4.1 22.4.2 22.4.3 Serrated with central bulb (225 mm wide, 8-11 mm thick) Dumb bell with central bulb (180 mm wide, 8 mm thick) Kickers (320 mm wide, 5 mm thick)
Unit
Rate
22.5
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick
sqm
215.15
22.6
sqm
311.50
22.7
364
Code No.
Description jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
Unit
Rate
sqm
786.70
22.8
Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or peasized gravel spread at 6 cubic diameter per square metre including preparation of surface but excluding grading complete with : 22.8.1 Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322 sqm 262.75
22.9
Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth course of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45, 1.20 and 1.45 Kg per square metre of area respectively, second and fourth courses of roofing felt type 3 grade I conforming to IS : 1322 (Hessian based self finished bitumen felt) conforming to IS : 1322 and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic dm per sqm including preparation of surface but excluding grading, complete. Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade I (fibre base self finished bitumen felt) six and final courses of stone grit 6 mm and down size or pea sized gravel spread at 6cu.dm per sqm including preparation of surface, excluding grading, compete. Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blow or/ and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade II (glass fibre base self finished bitumen felt) and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic dm per sqm including preparation of surface but excluding grading, complete. Supplying and applying bituminous solution primer on roof and or wall surface at 0.24 litre per sqm.
sqm
406.90
22.10
sqm
459.40
22.11
sqm sqm
459.60 24.00
22.12
365
Description Deduct for omitting in water proofing treatment final course of spreading stone grit 6 mm down size or pea sized gravel : 22.13.1 22.13.2 At 6 cudm per sqm at 8 cudm per sqm
Unit
Rate
sqm sqm
11.80 15.00
22.14
Grading roof for water proofing treatment with 22.14.1 22.14.2 22.14.3 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Cement mortar 1:3 (1 cement : 3 coarse sand) Cement mortar 1:4 (1cement : 4 coarse sand) cum cum cum 4,601.85 7,327.90 6,559.55
22.15
Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat ( item of laying brick tiles shall be paid for separately). Providing and laying in situ seven course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/sqm weight consisting
sqm
391.75
22.16
sqm
300.75
22.17
366
Code No.
Description of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).
Unit
Rate
sqm
493.95
22.18
Providing and fixing APP (Atactic Polypropylene Polymer) modified prefabricated five layer 2 mm thick water proofing membrance, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrance manufacture of density at 25C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23C as 350/300 N/ 5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150C. Cold flexibility shall be upto -2C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacture of membrane. 22.18.1 2mm (for corrugated roof sheets) sqm 323.15
22.19
Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150C. Cold flexibility shall be upto -2C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 22.19.1 3 mm thick sqm 374.25
22.20
Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and
367
Code No.
Description chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150C. Cold flexibility shall be upto -2C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 22.20.1 3 mm thick
Unit
Rate
sqm
422.80
22.21
Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.
sqm
53.85
368
369
371
cum
30.90
23.2
cum
260.70
23.3
cum
215.15
23.4
Rough dressing the trenched ground including breaking clods. Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. Fine dressing of the ground Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately). Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge.. Grassing with selection No.1 grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the good earth shall be paid for separately). 23.10.1 23.10.2 In rows 5 cm apart in both directions With grass Turf
cum cum
21.00 14.35
23.9 23.10
100sqm 100sqm
700.25 528.10
23.11
Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid for separately). Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking
100sqm
1,353.10
23.12
372
Code No.
Description repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.
Unit
Rate
100sqm
2,402.55
23.13
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : 23.14.1 23.14.2 23.14.3 23.14.4 Holes 1.2 m dia and 1.2 m deep Holes 90 cm dia, and 90 cm deep Holes 60 cm dia, and 60 cm deep Holes 45 cm dia, and 45 cm deep
cum
87.50
23.14
23.15
Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete : 23.15.1 With common burnt clay F.P.S. (non modular) bricks of class designation 5 each 902.55
23.16
Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia. and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge. Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including
each
2,580.60
23.17
373
Code No.
Description providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with : 23.17.1 23.17.2 A coat of coal tar Two or more coats of synthetic enamel paint of approved quality shade over a priming coat
Unit
Rate
each each
191.30 299.30
23.18
Making tree guard 53 cm dia and 2 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing four legs 40 cm long of 30 x 3 mm M.S. flat riveted to tree guard and providing and fixing 2 nos. M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with : 23.18.1 23.18.2 A coat of coal tar Two or more coats of synthetic enamel paint of approved brand and shade over a priming coat each each 381.00 547.50
23.19
Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : 23.19.1 Common burnt clay F.P.S. (non modular) bricks of class designation 7.5 metre 23.55
23.20
Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded). Excavation in dumped stones or malba including stacking of serviceable and unserviceable material separately and disposal of unserviceable material, lead up to 50 m and lift up to 1.5 m, disposed material to be neatly dressed. Excavation in bajri path including stacking of serviceable and unserviceable material separately, lead up to 50 m and lift up to 1.5 m, disposed material to be neatly dressed. Excavation in water bound macadam road including stacking the serviceable and unserviceable material separately and disposal of unserviceable material, lead up to 50 m and lift up to 1.5 m, disposed material to be neatly dressed. Flooding the ground with water including making kiaries and dismantling the same. Supplying and stacking of well decayed cow dung manure at site including royalty and carriage upto 1 km (Cow dung manure measured in stacks will reduced by 8% for Payment). Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level. The vertical members shall consist of four nos angle iron of size 25x25x3 mm, 1.8 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical mambers shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical
cum
7.15
23.21
cum
200.80
23.22
cum
223.80
23.23
cum 100sqm
275.40 110.85
23.24
cum
128.95
23.26
374
Code No.
Description member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect.
Unit
Rate
each
1,540.85
23.27
Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground , including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect. Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 nos ( 3 nos horizontal & 4 nos vertical "U" shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. 23.29.1 23.29.2 Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm
each
2,401.60
23.28
cum
178.70
23.29
each each
148.30 109.00
23.30
Providing Square Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size), reinforced with 7 nos. ( 3 nos horizontal & 4 nos vertical "U" shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height , all complete as per direction of Officer-in-charge. 23.30.1 Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and wall thickness 25.4 mm each 179.65
375
377
day day day day day litre metre metre metre metre each each each each metre metre cum cum cum cum metre metre metre each each each each each each each cum L.S.
7,500.00 247.00 247.00 301.00 273.00 41.29 1,042.00 1,250.00 460.00 834.75 150.00 180.00 170.00 200.00 465.15 840.00 332.00 650.00 625.00 650.00 750.00 385.00 390.00 120.00 140.00 750.00 600.00 165.00 200.00 250.00 650.00 1.49
0113 0114 0123 0124 1235 7743 7744 7745 7746 7747 7748 7749 7750 7751 7752 7753 7754 7755 7756 7757 7758 7759 7760 7761 7762 7763 7764 7765 7766 7772 9999
379
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 24.2.1 24.2.1.1 24.2.1.2 24.2.1.3 24.2.2 24.2.2.1 24.2.2.2 24.2.2.3 All types of soil 300 mm dia 350 mm dia 400 mm dia Rocky strata including Boulders 300 mm dia 350 mm dia 400 mm dia metre metre metre 851.20 875.10 1,096.60 metre metre metre 418.75 465.30 628.10
24.3
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 24.3.1 24.3.2 24.3.3 100 mm nominal size dia 150 mm nominal size dia 200 mm nominal size dia metre metre metre 452.00 539.15 975.60
24.4
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with
380
Code No.
Description ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 24.4.1 24.4.2 24.4.3 100 mm nominal size dia 150 mm nominal size dia 200 mm nominal size dia
Unit
Rate
24.5
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 24.10.1 24.10.2 24.10.3 100 mm nominal size dia having minimum wall thickness 5.00 mm 150 mm nominal size dia having minimum wall thickness 5.00 mm 200 mm nominal size dia having minimum wall thickness 5.40 mm
cum
459.05
24.6
cum
828.45
24.7
cum
799.40
24.8
cum
842.80
24.9
each
897.10
24.10
24.11
Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS:
381
Code No.
Description 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 24.11.1 24.11.2 24.11.3 100 mm nominal size dia 150 mm nominal size dia 200 mm nominal size dia
Unit
Rate
24.12
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 24.13.1 24.13.2 24.13.3 100 mm dia 150 mm dia 200 mm dia
hour
549.10
24.13
24.14
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 24.14.1 24.14.2 24.14.3 100 mm clamp 150 mm clamp 200 mm clamp each each each 977.70 1,033.10 1,173.25
24.15
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 24.15.1 24.15.2 24.15.3 100 mm dia 150 mm dia 200 mm dia each each each 171.30 206.10 240.95
382
383
385
sqm
19.85
25.2
sqm
127.10
sqm
62.70
25.4
sqm
26.80
25.5
sqm
104.30
386
Description Ruled/ Flush pointing on White sand stone masonry surface with lime, surkhi and marble dust mortar in the ratio of 1:1.5:1/2 {One lime : 1.5 surkhi (15% dark red and 85% light yellow surkhi) : 1/2 marble dust}. (The rate is inclusive of all materials & labours involved except scaffolding). Applying two or more coat of Ethyl Silicate chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacturer, with brush or spray on the existing stone masonry surface till there is no further absorption of chemical by stone surface, including protecting the applied surface from direct sunlight by suitable means during application, all complete as per direction of the Engineer-in-Charge (The rate is inclusive of all materials & labours involved except scaffolding). Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).
Unit
Rate
sqm
104.30
25.7
sqm
267.00
25.8
sqm
69.70
387
389
Cement Mortar 1:1 (1 cement : 1 fine sand). Cement mortar 1:2 (1 cement : 2 fine sand). Cement mortar 1:3 (1 cement : 3 fine sand). Cement mortar 1:4 (1 cement : 4 fine sand). Cement mortar 1:5 (1 cement : 5 fine sand). Cement mortar 1:6 (1 cement : 6 fine sand). Cement mortar 1:2 (1 cement : 2 coarse sand). Cement mortar 1:3 (1 cement : 3 coarse sand). Cement mortar 1:4 (1 cement : 4 coarse sand). Cement mortar 1:5 (1 cement : 5 coarse sand). Cement mortar 1:6 (1 cement : 6 coarse sand). Cement mortar 1:2 (1 cement : 2 stone dust). Cement mortar 1:2 (1 cement : 2 marble dust). Cement mortar 1:5 (1 cement : 5 marble dust). White cement mortar 1:2 (1 white cement : 2 marble dust). White cement mortar 1:3 (1 white cement : 3 marble dust). White cement mortar 1:5 (1 white cement : 5 marble dust).
cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum cum
391
CEMENT CONCRETE (CAST - IN- SITU) 4.1 P/L cement concrete - all works upto plinth level : 4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 4.1.8 4.1.9 4.1.10 4.1.11 4.1.12 1:1:2 (1 Cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1:3 (1 Cement : 1 coarse sand : 3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 1:3:6 (1 Cement : 3 fine sand : 6 graded stone aggregate 40 mm nominal size) 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 1:4:8 (1 cement : 4 fine sand : 8 graded stone aggregate 40 mm nominal size) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) 1:2:3:9 (1 ordinary portland cement : 2 Fly ash : 3 coarse sand : 9 graded stone aggregate 40 mm nominal size) 1:2:4:11 (1 ordinary portland cement : 2 fly ash : 4 coarse sand : 11 graded stone aggregate 40 mm nominal size) cum cum cum cum cum cum cum cum cum cum cum 6.10 4.00 3.20 3.20 2.20 2.20 2.20 1.70 1.70 1.30 1.30
cum
1.70
4.1.13
cum
1.30
4.2
P/L cement concrete in retaining walls, return walls etc.: 4.2.1 4.2.2 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1:3 (1 cement:1 coarse sand:3 graded stone aggregate 20 mm nominal size) cum cum 6.10 4.00
392
Code No.
Description
Unit
1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 1:3:6 (1 cement : 3 fine sand : 6 graded stone aggregate 40 mm nominal size) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
P/L cement concrete in kerbs, steps etc.: 4.4.1 4.4.2 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum 3.20 2.20
CEMENT CONCRETE (PRE-CAST) 4.5 P/F precast cement concrete string or lacing courses, copings etc.: 4.5.1 4.5.2 4.5.3 4.6 1:1:3 (1 cement:1 coarse sand:3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum cum 4.05 3.19 2.19
P/F precast cement concrete in kerbs, edgings etc.: 4.6.1 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum 3.25
4.7
P/F precast cement concrete solid blocks: 4.7.1 4.7.2 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum 3.76 2.76
4.8
P/F precast cement concrete hollow blocks: 4.8.1 4.8.2 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) cum cum 2.099 1.693
393
Code No.
Description
Unit
4.9
Precasting and placing in position 125 mm dia Bollards 600 mm high. DAMP- PROOF COURSE
each
0.097
4.10 4.11
P/L D.P.C. 40 mm thick with C.C. (1:2:4). P/L D.P.C. 50 mm thick with C.C. (1:2:4). MISCELLANEOUS
sqm sqm
0.13 0.16
4.17 4.19
Making plinth protection 50 mm thick of cement concrete 1:3:6 P/L Ready mixed concrete using flyash: 4.19.1 All works upto plinth level
sqm
0.11
4.19.1.1 M-15 grade plain cement concrete 4.19.1.2 M-10 grade plain cement concrete 4.19.2 All works above plinth and upto floor V level
cum cum
2.40 2.20
4.19.2.1 M-15 grade plain cement concrete 4.19.2.2 M-10 grade plain cement concrete 4.20 P/L ready mix plain cement concrete : 4.20.1 All works upto plinth level
cum cum
2.40 2.20
4.20.1.1 M-15 grade plain cement concrete 4.20.1.2 M-10 grade plain cement concrete 4.20.2 All works above plinth and upto floor V level
cum cum
2.40 2.20
4.20.2.1 M-15 grade plain cement concrete 4.20.2.2 M-10 grade plain cement concrete
cum cum
2.40 2.20
394
CAST-IN-SITU 5.1 P/L R.C.C. upto plinth level : 5.1.1 5.1.2 5.1.3 5.2 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum cum cum 6.10 4.00 3.20
R.C.C work in walls etc.: 5.2.1 5.2.2 5.2.3 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum cum cum cum cum cum cum cum cum 6.10 4.00 3.20 3.20 3.20 3.20 3.20 3.20 4.00
R.C.C. (1:2:4) work in beams etc. R.C.C. (1:2:4) work in kerbs, steps etc. R.C.C. (1:2:4) work in arches,domes etc. R.C.C. (1:2:4) work in chimneys & shafts. R.C.C. (1:2:4) work in well-steining. R.C.C. (1:1.5:3) work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards. PRE - CAST R.C.C.
P/F precast R.C.C. (1:2:4) work in string courses, bands, copings, bed plates, anchor blocks, plain window sills etc. P/F precast R.C.C. (1:2:4) in small lintels not exceeding 1.5m clear span. P/F precast R.C.C. (1:2:4) in mouldings as in cornices, windows sills etc.
P/F precast R.C.C. (1:2:4) in lintels, beams and bressumers etc. cum P/F precast R.C.C. (1:2:4) in shelves. cum
P/F precast R.C.C. (1:2:4) in vertical & horizontal fins individually or forming box louvers. cum
395
Code No.
Description
Unit
5.18
Fixing precast cement concrete Jali (1:2:4). 5.18.1 50 mm thick 5.18.2 40 mm thick 5.18.3 25 mm thick * Cement for fixing only. ENCASING ROLLED STEEL SECTION 100 sqm 100 sqm 100 sqm 1.64* 1.64* 1.64*
5.19 5.20
Encasing rolled steel sections, in beams and columns, with cement concrete (1:2:4). Encasing rolled steel section in grillages with cement concrete (1:2:4). MISCELLANEOUS
cum cum
3.20 3.20
Smooth finishing of exposed surface of R.C.C. work with 6 mm thick cement mortar (1:3). Rendering smooth the top of suspended floors, landings and staircases with cement mortar (1:2). Providing and filling in position bitumen mix filler.
3.67 4.17
0.00032
DESIGN MIX CONCRETE 5.33 5.34 P/L Design mix concrete (M-25). Extra for providing richer mixes at all floor levels : 5.34.1 Providing M-30 grade concrete instead of M-25 grade B.M.C/ R.M.C. 5.34.2 Providing M-35 grade concrete instead of M-25 grade B.M.C./ R.M.C. 5.34.3 Providing M-40 grade concrete instead of M-25 grade B.M.C./ R.M.C. 5.36 5.37 5.40 P/F precast R.C.C. in waffle units. P/L RMC manufactured in fully automatic batching plant M-25 grade R.C.C. P/L design mix cement concrete M-25 using Fly ash. * Actual weight for design mix will be worked out taking into consideration the cement requirement as per particular mix design.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. -5.0 REINFORCED CEMENT CONCRETE
cum
3.30*
396
Brick work in foundation & plinth with non modular bricks. 6.1.1 6.1.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) With non modular bricks. With modular bricks. Cement mortar 1:4 (1 cement : 4 coarse sand) Cement mortar 1:6 (1 cement : 6 coarse sand) cum cum cum cum cum cum cum cum 100 metre 100 sqm cum 0.95 0.625 0.836 0.55 0.625 0.55 0.95 0.625 3.86 9.23 1.28
6.2
Brick work in foundation & plinth with modular bricks. 6.2.1 6.2.2
6.3
6.4
Half brick masonry in cement mortar (1:3) for closing cavity 5 to 7.5 cm wide in cavity wall. Brick work 7 cm in cement mortar (1:3). Brick work in plain & gauged arches in cement mortar (1:3). HALF BRICK MASONRY Half brick masonry in foundations & plinth and superstructure. 6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) & 6.13.1 6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) & 6.13.2 BRICK TILE WORK
100 sqm
14.28
100 sqm
10.64
6.16
Tile brick masonry in foundation and plinth. : 6.16.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 6.16.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum cum cum cum 100 sqm 1.52 1.00 1.00 1.33 7.65
Tile brick masonry with m/c moulded tiles in cement mortar 1:6 (1 cement : 6 coarse sand). Tile brick masonry with tile bricks in plain/gauged arches work in in cement mortar (1:4). Tile brick masonry work 5 cm thick in cement mortar (1:3).
397
Code No.
Description
Unit
HONEY COMB WORK 6.23 6.26 6.27 6.28 6.29 6.30 6.31 6.32 Honey-comb brick work 10/11.4 cm thick in cement mortar 1:4. EXPOSED BRICK WORK Brick work with selected bricks in cement mortar (1:6). Brick work with modular bricks in cement mortar (1:6). Brick work with machine moulded modular bricks in cement mortar (1:6). Brick work with m/c moulded F.P.S. bricks in cement mortar (1:6). Brick work with machine moulded perforated F.P.S. bricks in cement mortar (1:6). Brick work with machine moulded perforated modular bricks in cement mortar (1:6). Brick work with clay flyash F.P.S. brick. 6.32.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 6.34 Brick work with non modular fly ash lime bricks (FALG Bricks) in : 6.34.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) 6.35 Brick work with modular calcium silicate bricks machine moulded in : 6.35.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 6.35.3 Cement mortar 1:6 (1 cement : 6 Coarse sand) 6.36 Brick work with modular extruded burnt fly ash clay sewer bricks in : 6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) 6.37 6.38 6.42 Brick work with modular extruded burnt fly ash clay sewer bricks in cement mortar (1:3). Autoclaved aerated cement blocks masonry with 100mm thick AAC blocks in cement mortar (1:4). Brick work with mechanized autoclaved flyash, sand lime bricks. : 6.42.1 Cement mortar 1:4 (1 cement :4 coarse sand) 6.42.2 Cement mortar 1:6 (1 cement :6 coarse sand) 6.44 6.45 Brick edging 7 cm wide in cement mortar (1:4). Half brick masonry with non modular FALG bricks. 6.45.1 Cement mortar 1:3 (1 cement :3 coarse sand). 6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand). 6.46 Half brick masonry with non modular mechanized Autoclaved flyash sand lime bricks. 6.46.1 Cement mortar 1:3 (1 cement :3 coarse sand) 6.46.2 Cement mortar 1:4 (1 cement :4 coarse sand)
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. -6.0 BRICK WORK
100 sqm cum cum cum cum cum cum cum cum cum cum cum cum
6.56 0.625 0.55 0.55 0.625 0.625 0.55 0.95 0.625 0.95 0.625 0.836 0.55
cum cum cum cum cum 100 metre 100 sqm 100 sqm
14.28 10.64
398
RANDOM RUBBLE MASONRY 7.1& 7.2 COURSED RUBBLE MASONRY 7.6 Coursed rubble masonry (first sort) with : 7.6.1 7.7 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 0.750 Random rubble masonry with cement mortar (1:6). cum 0.825
Coursed rubble masonry (second sort) with : 7.7.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 0.750
ASHLAR MASONRY 7.12 7.13& 7.14 7.15 Stone work in plain ashlar in cement mortar (1:6) including pointing with white cement mortar (1:2). Stone work plain ashlar in arches/domes in cement mortar (1:3) including pointing with white cement mortar (1:2). Stone work ashlar punched in cement mortar 1:6) including pointing with white cement mortar (1:2). SUNK, MOULDED, CARVED ASHLAR MASONRY 7.20 Stone work sunk and / or moulded including pointing with white cement mortar (1:2). MISCELLANEOUS STONE WORK 7.23 Stone work (machine cut edges) for wall lining etc. (veneer work) in cement mortar (1:3) including pointing in white cement mortar (1:2). 100 sqm P/F stainless steel cramps in stone wall lining in cement mortar (1:2). P/F stone dowels 10x5x2.50 cm in cement mortar (1:2) . P/F copper pins 7.5 cm long 6 mm diameter in stone wall lining in cement mortar (1:2). kg each each cum 0.54 cum cum cum 0.54 1.07 0.54
P/F sloping chajja of stone 40 mm thick and upto 80 cm wide in cement mortar (1:4) i/c pointing in white cement mortar (1:2). 100 sqm P/F horizontal chajja of stone 40 mm thick and upto 80 cm projection in cement mortar (1:4) i/c pointing in white cement mortar (1:2). P/F 30 mm red sand stone sun-shade with cement mortar 1:4 including finishing complete. Providing and fixing red sand stone brackets 55x22.5x45cm.
7.30 7.31
399
Code No.
Description
Unit
7.32
Stone work, plain in copings, cornices, string courses etc. in Cement mortar 1:6 including pointing with white cement mortar (1:2). Wall lining butch work with Dholpur stone 40 mm thick, in cement mortar (1:3) including ruled pointing in cement mortar (1:2). Stone work ( machine cut edges) for wall lining with grout of 12 mm thick in cement mortar (1:3) and jointed with Cement mortar (1:2). Stone tile work for wall lining with 12 mm thick bed in cement mortar (1:3). STONE WORK IN DRY CLADDING P/F structural steel frame (for dry stone cladding) embedded in brick wall with cement concrete block (1:2:4) * White cement
cum
0.54
7.36
100 sqm
15.50 +1.70*
7.37
7.38
7.41
100kg
1.05
400
1.0 COEFFICIENTS FOR CEMENT CONSUMPTION 8.0 MARBLE & GRANITE WORK
Code No. 8.1 8.2 Description Unit Quantity of cement per unit quantity of work (Quintals) 8.67 + 1.70*
Marble work 18 mm thick for wall lining in cement mortar 1:3 including pointing with white cement mortar 1:2. P/F 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters etc. laid over 20mm thick base cement mortar 1:4. Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. P/F cramps in RCC/ CC backing with cement mortar 1:2 . 8.7.1 8.7.2 Gunmetal cramps Stainless steel cramps
9.12
8.4
1.27
8.7
kg kg 100 sqm
0.0635 0.0701
8.9
Stone tile work for wall lining over 12mm thick bed of cement mortar (1:3) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.
10.44 + 1.90*
* White cement
401
1.0 COEFFICIENTS FOR CEMENT CONSUMPTION 9.0 WOOD AND P.V.C. WORK
Code No. Description Unit Quantity of cement per unit quantity of work (Quintals)
MISCELLANEOUS - WOOD WORK 9.32 9.34 9.46 9.47 9.53 P/F 50x50x50 mm 2nd class teak wood plugs in cement mortar 1:3. P/F 2nd class teak wood plain lining with wooden plugs. P/F curtain rods of 1.25 mm thick chromium plated brass brackets with wooden plugs, etc. Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. Providing 40x5 mm flat iron hold fast 40 cm long with cement concrete block 30x10x15cm 1:3:6 mix. 100 nos 100 sqm 100 metre 100 metre 100 nos 0.01 0.055 0.01 0.01 1.10
COEFFICIENTS FOR CEMENT CONSUMPTION S.H.: -9.0 WOOD AND PVC WORK
402
P/F 1 mm thick M.S. sheet sliding-shutters with frame. P/F 1 mm thick M.S. sheet door with frame. Supplying and fixing rolling shutters.
10.10.1 & Fixing standard steel glaze door windows etc. 10.11.1 10.13.1 10.15 P/F T iron froms for doors windows & ventilators Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with 15x3 mm lugs 10 cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 mix.
100 kg
0.28
403
Brick on edge flooring. 11.1.1 1:4 (1 cement : 4 coarse sand) 11.1.2 1:6 (1cement : 6 coarse sand) sqm sqm sqm sqm sqm sqm cum 0.1850 0.1285 0.17 0.231 0.263 0.14 3.20
Cement concrete flooring 1:2:4. 11.3.1 40mm thick with 20mm nominal size stone aggregate 52 mm thick cement concrete flooring. 62 mm thick cement concrete flooring. Cement plaster skirting with cement mortar (1:3). Cement concrete pavement with C.C. (1:2:4). TERRAZO FLOORING 40 mm thick marble chips flooring with under layer 34 mm thick cement concrete (1:2:4). 11.9.1 Dark shade pigment with ordinary cement 11.9.2 Light shade pigment with white cement 11.9.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.9.4 White cement without any pigment 11.9.5 Light shade pigment with ordinary cement 11.9.6 Ordinary cement without any pigment sqm sqm sqm sqm sqm sqm 0.1695 0.129+0.0405* 0.1492+0.0202* 0.129+0.0202* 0.1695 0.1695
11.10
40 mm thick marble chips flooring with under layer 31mm thick cement concrete 1:2:4. 11.10.1 Dark shade pigment with Ordinary cement 11.10.2 Light shade pigment with white cement 11.10.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.10.4 White cement without any pigment 11.10.5 Light shade pigment with ordinary cement 11.10.6 Ordinary cement without any pigment sqm sqm sqm sqm sqm sqm 0.1783 0.1205+0.0578* 0.1494+0.0289* 0.1205+0.0578* 0.1783 0.1783
11.11
40 mm thick marble chips flooring with under layer 28 mm thick cement concrete 1:2:4. 11.11.1 Dark shade pigment with ordinary cement 11.11.2 Light shade pigment with white cement 11.11.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.11.4 White cement without any pigment sqm sqm sqm sqm 0.1907 0.1097+0.081* 0.1502+0.0405* 0.1097+0.081*
404
Code No.
Description
Unit
Light shade pigment with ordinary cement Ordinary cement without any pigment 18 mm thick with under layer 12 mm thick in cement plaster 1:3 (1 cement : 3 coarse sand) :
sqm sqm
11.12.1.1 Dark shade pigment with ordinary cement 11.12.1.2 Light shade pigment with white cement 11.12.1.3 Medium shade pigment with 50% white cement and 50% ordinary cement 11.12.1.4 White cement without any pigment 11.12.1.5 Light shade pigment with ordinary cement 11.12.1.6 Ordinary cement without any pigment 11.15 Crazy marble stone flooring. 11.15.1 18 mm thick crazy marble stone white, black or as specified * White Cement TILE FLOORING 11.16 Precast terrazo tiles 22mm thick in floors, and landings on 20mm thick bed of cement mortar (1:4). 11.16.1 11.16.2 11.16.3 11.16.4 11.18 Light shade using white cement Medium shade using 50%white cement and 50% ordinary cement Dark shade using ordinary cement Ordinary cement without any pigment
sqm
0.1200+0.0405*
Precast terrazo tiles 22 mm thick in skirting and risers of steps. 11.18.1 11.18.2 11.18.3 11.18.4 Light shade using white cement. Medium shades using 50% white cement and 50% ordinary cement. Dark shade using ordinary cement Ordinary cement without any pigment sqm sqm sqm sqm 0.0734+0.066* 0.1064+0.033* 0.1394 0.1394
11.19
Chequered terrazo tiles 22 mm thick in floors on 20 mm thick bed of cement mortar (1:4). 11.19.1 11.19.2 11.19.3 11.19.4 Light shade using white cement Medium shade using 50% white cement, 50% ordinary cement Dark shade using ordinary cement Ordinary cement without any pigment sqm sqm sqm sqm 0.0895+0.044* 0.0917+0.024* 0.0939 0.0939
405
Description
Unit
Chequerred precast cement concrete tiles 22 mm thick in foot path on 20 mm thick bed of cement mortar (1:4). 11.20.1 11.20.2 11.20.3 11.20.4 Light shade using white cement Medium shade using 50% white cement 50% Grey cement Dark shade using ordinary cement Ordinary cement without any pigment In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) sqm 0.0786** In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) sqm sqm 0.0862** 0.1044 sqm sqm sqm sqm 0.1291+0.066* 0.1621+0.033* 0.1951 0.1951
11.21
Providing and fixing 10mm thick acid and or alkali resistant tiles. 11.21.1
11.21.2.1 Acid and alkali resistant tile 11.22 Tile work in skirting, risers of steps etc. with 8 mm thick marble tile. STONE FLOORING 11.23 Marble stone flooring with 18 mm thick marble stone over 20 mm thick cement mortar (1:4). KOTA STONE FLOORING 11.26 11.27 Kota stone slab flooring over 20 mm thick bed of cement mortar (1:4). Kota stone slabs 20 mm thick in risers of steps, skirting etc. laid on 12 mm (average) thick cement mortar 1:3. SAND STONE FLOORING 11.28 11.29 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 with joints finished flush. 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 including pointing with cement mortar 1:2. 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 with joints 3mm thick, side buttered with cement mortar 1:2. CERAMIC GLAZED TILES 11.36 11.37 11.38 11.39& 11.40 P/F 1st quality ceramic glazed wall tiles over 12 mm thick bed of cement Mortar (1:3). P/L ceramic glazed floor tiles laid on 20 mm thick Cement Mortar (1:4). P/L ceramic glazed floor tiles laid on 20mm thick bed of Cement Mortar (1:4). P/L rectified Glazed Ceramic floor tiles laid on 20mm thick cement mortar (1:4).
sqm
0.13512
sqm sqm
0.1491 0.1374
sqm
0.0775
sqm
0.0931
11.30
sqm
0.0931
406
Code No.
Description
Unit
VITRIFIED FLOOR TILES 11.41 11.44 11.46 P/L vitrified floor tile laid on 20mm thick cement mortar (1:4). Crazy ceramic tile flooring. P/L vitrified tile in skirting in cement mortar (1:3). * White cement ** Acid alkali resistant cement. sqm sqm sqm 0.1242 0.0646 0.088
407
10 cm thick mud phaska with flat tile bricks grouted with cement mortar (1:3). 10cm thick mud phaska with machine moulded tile bricks grouted with cement mortar (1:3). Providing and laying brick tiles over mumty roofs grouted with cement mortar (1:3). Providing and laying pressed clay tiles on roofs jointed with cement mortar (1:4). Providing gola 75x75 mm in cement concrete (1:2:4). Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4). Providing sand stone slab for roofing and laying cement mortar (1 : 4). Providing and fixing M.S. holder bat clamps in cement concrete blocks 10x10x10cm of 1:2:4 mix. P/F heat resistant tile on roof with cement mortar (1:4) and filling joints with white cement marble mix. * White cement
100 sqm 100 sqm 100 sqm 100 sqm metre each 100 sqm each sqm
408
CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster: 13.1.1 1:4 (1 cement : 4 fine sand) 13.1.2 1:6 (1 cement : 6 fine sand) 13.2 15 mm cement plaster: 13.2.1 1:4 (1 cement : 4 fine sand) 13.2.2 1:6 (1 cement : 6 fine sand) 13.3 20 mm cement plaster : 13.3.1 1:4 (1 cement : 4 fine sand) 13.3.2 1:6 (1 cement : 6 fine sand) CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster : 13.4.1 1:4 (1 cement : 4 coarse sand) 13.4.2 1:6 (1 cement : 6 coarse sand) 13.5 15 mm cement plaster : 13.5.1 1:4 (1 cement : 4 coarse sand) 13.5.2 1:6 (1 cement : 6 coarse sand) 13.6 20 mm cement plaster : 13.6.1 1:4 (1 cement : 4 coarse sand) 13.6.2 1:6 (1 cement : 6 coarse sand) CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 13.7 12 mm cement plaster finished with a floating coat of neat cement : 13.7.1 1:3 (1 cement : 3 fine sand) 13.7.2 1:4 (1 cement : 4 fine sand) 13.8 15 mm cement plaster finished with a floating coat of neat cement : 13.8.1 1:3 (1 cement : 3 fine sand) 13.8.2 1:4 (1 cement : 4 fine sand) 13.9 Cement plaster (1:3) finished with a floating coat of neat cement. 13.9.1 12 mm Cement Plaster 13.9.2 20 mm Cement Plaster
COEFFICIENTS FOR CEMENT CONSUMPTION S.H.: -13.0 FINISHING
100 sqm 100 sqm 100 sqm 100 sqm 100 sqm 100 sqm
100 sqm 100 sqm 100 sqm 100 sqm 100 sqm 100 sqm
9.54 7.67
10.97 8.74
9.54 13.62
409
Description
Unit
15 mm cement plaster (1:3) finished with a floating coat of neat cement. CEMENT PLASTER IN TWO COATS
100 sqm
13.11
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 finished with a top layer 6mm thick cement plaster 1:6. 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 and a top layer 6mm thick cement plaster (1:3). 12 mm cement plaster 1:2 (1 cement : 2 stone dust). 15 mm cement plaster 1:2 (1 cement : 2 stone dust). 20 mm cement plaster 1:2 (1 cement : 2 stone dust). 6 MM CEMENT PLASTER
100 sqm
6.26
13.12
13.16
6 mm cement plaster of mix : 13.16.1 1:3 (1 cement : 3 fine sand) 100 sqm 100 sqm 100 sqm 3.67 5.87 2.20
13.17 13.18
6 mm cement plaster (1:3) finished with a floating coat of neat cement. Neat cement punning ROUGH CAST PLASTER
13.19
Rough cast plaster in two layers, under layer 12 mm cement plaster (1:4) and top layer 10mm cement plaster (1:3). PEBBLE DASH PLASTER
100 sqm
11.59
13.20
Pebble dash plaster in two layers, under layer 12mm cement plaster 1:4 and top layer 10mm cement plaster with cement mortar (1:3) . PLAIN CEMENT MORTAR BANDS
100 sqm
11.59
12 mm thick plain cement mortar bands in cement mortar (1:4) : (Flush /Sunk / Raised / Moulded Band). 18 mm thick plain cement mortar band in cement mortar (1:4). 18 mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5, top layer 6mm thick with cement mortar (1:4). POINTING OF BRICK WORK
100 metre 1cm wide 100 metre 1cm wide 100 metre 1cm wide
0.053 0.076
0.07
13.31
Pointing on brick work with cement mortar (1:3) : 13.31.1 Flush / Ruled/ Struck or weathered pointing 13.31.2 Raised and cut pointing 100 sqm 100 sqm 1.53 2.04
410
Code No.
Description
Unit
POINTING ON TILE BRICK WORK 13.32 Pointing on tile brick work with cement mortar (1:3). 13.32.1 Flush/ Ruled/ Struck or weathered pointing POINTING ON STONE WORK 13.33 Pointing on stone work with cement mortar (1:3). 13.33.1 Flush/ Ruled pointing 13.33.2 Raised and cut pointing 13.34 13.35 13.72 Raised and cut pointing on stone work in white cement mortar (1:3). Pointing on stone slab ceiling with cement mortar (1:2). Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4), top layer 15mm cement plaster 1:1/2:2. Note: - cement consumption for pointing is same for modular & non modular bricks. * White cement 100 sqm 100 sqm 100 sqm 100 sqm 1.17 2.35 2.35* 1.02 100 sqm 2.35
100 sqm
17.472
411
Repairs to plaster of thickness 12 mm to 20 mm in patches with cement mortar 1:4. Fixing chowkhats in existing opening with hold fasts in cement concrete blocks with cement concrete 1:3:6. 14.2.1 Door chowkhats 14.2.2 Window chowkhats 14.2.3 Clerestory window chowkhats
100 sqm
each each each each 100 sqm 100 sqm cum cum 100 sqm
Providing and fixing 16 mm M.S. Fan clamps in existing R.C.C. slab. Regrading terracing of mud phaska to proper slope. Replacing sand stone slabs in roofing in cement mortar 1:4. Renewing wooden battens in roofs & making good the holes in walls. Renewing wooden beams in roofs & making good the holes in walls. Flush pointing with cement mortar 1:3 for flat tile bricks on top of mud phaska.
412
FENCING 16.23 16.24 P/F boundary stone including finishing smooth with cement mortar (1:3). P/F precast R.C.C. kilometre stone including finishing smooth in cement mortar (1:3). 16.24.1 16.24.2 16.24.3 16.42 16.43 35x111x25 cm size 50x152.5x25 cm size 35x93.5x18 cm size each each each cum 0.37 0.698 0.23 3.20 each 0.082
CONCRETE PAVEMENT Cement concrete (1:2:4) in pavements. Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix. MISCELLANEOUS 16.49 16.52 Making bell mouth opening including providing cement concrete (1:3:6) & plastering with cement mortar (1:3). Providing and fixing precast lime fly ash concrete blocks including finishing with 10mm thick cement mortar (1:3), in foot paths. P/L kerb channel 30cm wide and 50mm thick of cement concrete (1:3:6). Providing and fixing factory made RCC pavement slab of M-30 grade in footpath over a bed of 20mm average thick cement mortar (1:5). Providing and laying factory made kerb stone of M-25 grade jointed with cement mortar (1:3). Providing and laying C.C. pavement of mix M-25 with ready mixed concrete. Dry lean cement concrete sub base. Laying old kerb stones, jointed with cement mortar (1:3). 10 nos 6.60
cum
3.40
sqm metre
0.05 0.11
16.63 16.67
413
17.1/17.2/ Fixing Indian type W.C. pan. 17.3 17.4 Fixing white vitreous china urinal basin : 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern 17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern 17.4.3 Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern 17.4.4 Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern 17.5 Fixing white vitreous china flat back half stall urinal : 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern 17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern 17.5.3 Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern 17.5.4 Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern 17.6 Fixing one piece construction white vitreous china squatting plate : 17.6.1 Single squatting plate with 5 litre P.V.C. automatic flushing cistern 17.6.2 Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern 17.6.3 Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern 17.6.4 Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern 17.7 17.8 17.9/ 17.10/ 17.11 17.12 17.13 17.17 17.23 Fixing wash basin with C.I. brackets. Fixing white vitreous china pedestal for wash basin. Fixing kitchen sink with C.I. brackets.
each
Fixing draining board with C.I. brackets. Fixing White vitreous china water closet squatting pan. Fixing a pair of white vitreous china foot rests. Fixing white vitreous china flat urinal basin.
414
Code No. 17.24 17.25 17.26/ 17.27 17.37 17.59 17.60 17.61
Description
Unit
Quantity of cement per unit quantity of work (Quintals) 0.02 0.015 0.015 0.005 0.005 0.025
Fixing white vitreous china squatting plate urinal. Fixing white vitreous china wash basin. Fixing kitchen sink. Providing and fixing M.S. holder-bat clamps. Providing and fixing M.S. stays and clamps. Providing and fixing trap of self-cleansing design. Cutting chases in brick masonry walls for sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with C.C.(1:3:6). 17.61.1 17.61.2 17.61.3 100 mm dia 75 mm dia 50 mm dia
* White Cement.
415
Providing and fixing G.I./ PE-AL-PE/ PP-R pipes. Internal work - Exposed on wall 18.10.1 18.10.2 18.10.3 18.10.4 18.10.5 18.10.6 15 mm dia nominal bore 20 mm dia nominal bore 25 mm dia nominal bore 32 mm dia nominal bore 40 mm dia nominal bore 50 mm dia nominal bore 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 0.05 0.06 0.07 0.075 0.08 0.08 0.88
18.2/18.5/ 18.8/18.11 18.32 18.33 18.34 18.35 18.36 18.37 18.76 18.77
P/F concealed pipes. Constructing masonry Chamber 30x30x50 cm, for stop cock. Constructing masonry Chamber 60x60x75 cm, for sluice valve. Constructing masonry Chamber 90x90x100 cm, for sluice valve. Constructing masonry Chamber 120x120x100 cm, for sluice valve. Constructing masonry Chamber 60x60x75 cm, for fire hydrants. each Constructing masonry Chamber 60x45x50 cm, for water meter. Cutting holes up to 30x30 cm in walls including making good the same. Cutting holes up to 15x15 cm in R.C.C. floors and roofs and repairing the hole after insertion of drain pipes etc. with cement concrete (1:2:4). Making chases up to 7.5x7.5 cm in walls i/c finishing. Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete (1:3:6).
0.70 0.88
18.78 18.79
100 metre
4.90
416
Jointing glazed stoneware pipes with stiff mixture of cement mortar in the proportion of (1:1). 19.1.1 19.1.2 19.1.3 19.1.5 19.1.6 100 mm diameter 150 mm diameter 200 mm diameter 250 mm diameter 300 mm diameter 100 mm diameter S.W. pipe 150 mm diameter S.W. pipe 200 mm diameter S.W. pipe 250 mm diameter S.W. pipe 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 2.17 3.23 4.33 5.40 6.47 19.24 23.53 27.43 31.72
19.2
Laying cement concrete (1:5:10) alround S.W. pipes: 19.2.1 19.2.2 19.2.3 19.2.5
19.3
Laying cement concrete (1:5:10) upto haunches of S.W. pipes: 19.3.1 19.3.2 19.3.3 19.3.5 19.3.6 100 mm diameter S.W. pipe 150 mm diameter S.W. pipe 200 mm diameter S.W. pipe 250 mm diameter S.W. pipe 300 mm diameter S.W. pipe 100x100 mm size P type 150 x 100 mm size P type. 180x150 mm size P type 100 metre 100 metre 100 metre 100 metre 100 metre each each each 9.14 14.82 17.42 20.28 23.40 0.27 0.26 0.25
19.4
Providing and fixing square-mouth S.W. gully trap : 19.4.1 19.4.2 19.4.3
19.6
P/L NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of (1:2): 19.6.1 19.6.2 19.6.3 19.6.4 19.6.5 19.6.6 19.6.7 19.6.8 19.6.9 19.6.10 19.6.11 100 mm dia. R.C.C. pipe 150 mm dia. R.C.C. pipe 250 mm dia. R.C.C. pipe 300 mm dia. R.C.C. pipe 450 mm dia. R.C.C. pipe 500 mm dia. R.C.C. pipe 600 mm dia. R.C.C. pipe 700 mm dia. R.C.C. pipe 800 mm dia. R.C.C. pipe 900 mm dia. R.C.C. pipe 1000 mm dia. R.C.C. pipe 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 100 metre 0.50 0.60 0.90 1.10 2.40 2.60 3.20 3.70 4.20 4.90 5.50
417
Code No.
Description
Unit
Quantity of cement per unit quantity of work (Quintals) 6.10 6.80 2.92 4.73 1.26 1.52
1100 mm dia. R.C.C. pipe 1200 mm dia. R.C.C. pipe Inside size 90x80 cm and 45 cm deep
Constructing brick masonry manhole in cement mortar (1:4). 19.7.2& Inside size 120x90 cm and 90 cm.deep Extra for depth for manholes 19.8.1 19.8.2 Size 90x80 cm Size 120x90 cm metre metre
19.9
Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar (1:4). 19.9.1 0.91 m deep each metre 2.75 1.40 Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar (1:4). 19.11.1 1.68 m deep each metre 5.39 1.43 Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m. Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar (1:4). 19.13.1 2.30 m deep each metre 100 nos. 100 nos 100 nos 10.86 3.11 0.88 1.98 0.88 Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m. Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks (1:3:6). Providing orange colour safety foot rest. Replacement of M.S. foot rests in manholes with 20x10x10 cm C.C. blocks (1:3:6) mix. Providing and fixing in position precast R.C.C. manhole cover and frame. 19.19.1 19.19.1.1 19.19.1.2 19.19.1.3 19.19.2 L D- 2.5 Rectangular shape 600x450mm internal dimensions Square shape 450mm internal dimensions Circular shape 450mm internal diameter M D - 10 each each 0.128 0.096 each each each 0.128 0.096 0.096
19.10 19.11
19.12 19.13
19.19.2.1 Square shape 450mm internal dimension 19.19.2.2 Circular shape 500mm internal diameter 19.19.3 H D - 20
COEFFICIENTS FOR CEMENT CONSUMPTION S.H.:. -19.0 DRAINAGE
418
Code No.
Description
Unit
19.19.3.1 Circular shape 560 mm internal diameter 19.19.4 19.21 EHD - 35 19.19.4.1 Circular shape 560 mm internal dia Making connection of drain or sewer line with existing manhole and making good the walls, floors with C.C.(1:2:4) mix. 19.21.1 19.21.2 19.21.3 19.22 For pipes 100 to 250 mm diameter For pipes 250 to 300 mm diameter For pipes 350 to 450 mm diameter
each each
Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole. : 19.22.1 19.22.2 100 mm dia sand cast iron drop connection 150 mm dia sand cast iron drop connection each each 0.34 0.46
19.23
Extra for depths beyond 60 cm of sand cast iron drop connection. : 19.23.1 19.23.2 For 100 mm dia. sand cast iron drop connection For 150 mm dia. sand cast iron drop connection metre metre each each each 0.21 0.26 0.93 0.82 1.66
Constructing brick masonry road gully chamber 50x45x 60cm in cement mortar (1:4). Constructing brick masonry road gully chamber 45x45x 77.5 cm in cement mortar (1:4). Constructing brick masonry road gully chamber 110x50x 77.5 cm in cement mortar (1:4). Constructing brick masonry chamber for underground C.I. inspection chamber and bends in cement mortar (1:4). 19.30.1 19.30.2 19.30.3 Inside dimensions 455x610 mm and 45 cm deep for single pipe line Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets For 455x610 mm size For 500x700 mm size For 600x850 mm size
19.31
Extra for depth beyond 45 cm of brick masonry chamber : 19.31.1 19.31.2 19.31.3
19.32 19.34
Making soak pit 2.5 m diameter 3.0 metre deep. Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar (1:1). 19.34.1 19.34.2 100 mm dia 150 mm dia
each each
0.013 0.019
419
Providing, driving and installing driven cast-in-situ reinforced cement concrete piles of grade M -25. 20.1.1 20.1.2 20.1.3 20.1.4 20.1.5 20.1.6 20.1.7 20.1.8 400 mm dia piles 450 mm dia piles 500 mm dia piles 550 mm dia piles 750 mm dia piles. 1000 mm dia piles 1200 mm dia piles 1500 mm dia piles metre metre metre metre metre metre metre metre 0.414 0.525 0.648 0.784 1.456 2.590 3.729 5.83
20.2
Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M -25. 20.2.1 20.2.2 20.2.3 20.2.4 20.2.5 20.2.6 20.2.7 20.2.8 20.2.9 300 mm dia piles 400 mm dia piles 450 mm dia piles 500 mm dia. piles 600 mm dia piles 750 mm dia piles. 1000 mm dia piles 1200 mm dia piles 1500 mm dia pile metre metre metre metre metre metre metre metre metre 0.232 0.414 0.525 0.648 0.932 1.456 2.590 3.729 5.830
20.3
Boring, Providing and installing cast in situ single under reamed piles of grade M -25. 20.3.1 20.3.2 20.3.3 20.3.4 300 mm dia piles 400 mm dia piles 450 mm dia piles 550 mm dia piles 300mm dia piles 400mm dia piles 450 mm dia piles 550 mm dia piles metre metre metre metre each each each each 0.257 0.488 0.629 0.792 0.109 0.208 0.267 0.396
20.4
Extra for providing additional bulb in under reamed piles. 20.4.1 20.4.2 20.4.3 20.4.4
20.5
Providing, driving and installing driven Pre-cast reinforced cement concrete piles of grade M -25.
420
Code No.
Description
Unit
Quantity of cement per unit quantity of work (Quintals) 0.414 0.525 0.648 0.784 1.795 2.590
400 mm dia piles 450 mm dia piles 500 mm dia piles 550 mm dia piles 750 mm dia piles 1000 mm dia piles
421
P/L integral cement based treatment for water proofing on horizontal surface. : 22.1.1 Using rough kota stone sqm 0.342 P/L integral cement based treatment for water proofing on the vertical surface. : 22.2.1 Using rough Kota stone sqm 0.443 P/L water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: i) ii) Ist course of applying cement slurry @ 4.4 kg/sqm IInd course of 20mm cement plaster (1:3)
22.2
22.3
iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area iv) IVth course of 400 micron thick PVC sheet 22.5 22.6 22.7 P/L water proofing treatment in sunken portion of WCs, bathroom etc. P/L water proofing treatment on roofs. P/L integral cement based water proofing treatment on roofs, balconies, terraces etc. : 22.7.1 22.14 With average thickness of 120mm and minimum thickness at khurra as 65 mm Cement concrete 1:2:4 Cement mortar 1:3 Cement mortar 1:4 sqm cum cum cum 0.387 3.20 5.10 3.80 sqm sqm sqm 0.158 0.0123 0.0195
Grading roof for water proofing treatment with 22.14.1 22.14.2 22.14.3
422
Providing circular cement concrete pots. Providing square cement concrete pots.
423
425
SURFACE DRESSING 16.25 16.26 16.27 16.28 16.29 Surface dressing on new surface with paving bitumen of grade VG -10. Surface dressing on new surface in two coats with bitumen of grade VG -10. Surface dressing on old surface with hot bitumen of grade VG -10. Surface dressing one coat on new surface : 16.28.1 16.29.1 16.30 Using bitumen emulsion Using bitumen emulsion sqm sqm 0.0195 0.0122 Surface dressing one coat on old surface : PREMIX CARPET Providing and applying tack coat with bitumen of grade VG-10 : 16.30.1 16.30.2 16.31 On W.B.M. @ 0.75 Kg / sqm On bituminous surface @ 0.50 Kg / sqm sqm sqm 0.0075 0.0050 sqm sqm sqm 0.0225 0.029 0.0195
Providing and applying tack coat using bitumen emulsion (Rapid Setting): 16.31.1 16.31.2 On W.B.M @ 0.4kg/sqm On bituminous surface @ 0.25kg/sqm sqm sqm sqm sqm sqm sqm 0.0040 0.0025 0.0144 0.018 0.033* 0.0388*
2 cm premix carpet surfacing with paving asphalt VG-10/VG-30/modified bitumen CRMB 55. 2.5 cm premix carpet surfacing with paving asphalt VG-10/VG-30/modified bitumen CRMB 55. 2 cm premix carpet surfacing with bitumen emulsion. 2.5 cm premix carpet surfacing with bitumen emulsion. Providing and laying Bitumen Penetration Macadam : 16.36.1 16.36.2 For 50mm compacted thickness with paving asphalt VG-10 @ 50 kg/10 sqm For 75 mm compacted thickness in two layers with paving asphalt VG-10 @ 68 kg/10 sqm
sqm sqm
0.05 0.068
MASTIC AND BITUMASTIC WEARING COURSE 16.37 Providing and laying bitumen mastic wearing course: 16.37.1 16.37.2 25mm thick 40 mm thick sqm sqm 0.0586 0.0938
427
Code No.
Description
Unit
16.38 16.39
2.5 cm thick bitumastic sheet with hot bitumen, paving asphalt VG-10/VG-30/modified bitumen CRMB 55. 4 cm thick bitumastic sheet with hot bitumen, paving asphalt VG-10/VG-30/modified bitumen CRMB 55. SEAL COAT P/L seal coat using 128 kg of bitumen of grade VG-10. P/L seal coat using 98 kg of bitumen of grade VG-10. P/L Dense Bituminous macadam : 16.54.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
cum
1.5438
16.54.2
cum
1.5438
16.55
cum
0.7683
16.55.2
cum
0.7683
16.56
Providing and laying Semi Dense Bituminous concrete 16.56.1 25 mm compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 100 sqm 25 mm compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity. 100 sqm 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100120 TPH capacity.
2.884
16.56.2
2.884
16.57
cum
1.296
428
Code No.
Description
Unit
16.57.2
40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and waste plastic additive @ 8% (percentage by weight of bitumen) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade PMB-40 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade CRMB-60 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity. 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and waste plastic additive @ 8% (percentage by weight of bitumen) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity. 40/50 mm compacted thickness with bitumen of grade PMB-40 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in drum Type Hot Mix Plant of 60-90 TPH capacity.
cum
1.296
16.57.3
cum
1.296
16.57.4
cum
1.296
16.57.5
cum
1.296
16.57.6
cum
1.296
16.57.7
cum
1.296
16.57.8
40/50 mm compacted thickness with bitumen of grade CRMB-60 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
cum
1.296
429
P/L water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like. P/L water proofing treatment on roofs with cement slurry & fibre glass cloth. P/L four courses water proofing treatment with bitumen felt over roofs: 22.8.1 Bitumen felt (hessian base)type 3 grade I
sqm sqm
sqm
0.029
22.9
P/L six courses water proofing treatment with bitumen felt over roofs applied hot @ 1.45, 1.20 & 1.45 for 1st, 3rd and 5th course. P/L six courses water proofing treatment with bitumen felt over roofs applied hot @ 1.45, 120 & 1.70 for 1st, 3rd and 5th course. P/L in situ seven course water proofing treatment with APP (1.5 mm thick @ 2.25 kg./sqm). P/L in situ five course water proofing treatment with APP (2.00 mm thick @ 3.00 kg./sqm). P/L in situ seven course water proofing treatment with APP (2.00 mm thick @ 3.00 kg./sqm). P/F APP. 22.18.1 2mm (for corrugated roof sheets)
sqm
0.041
P/L APP modified prefabricated five layer, 3 mm thick water proofing membrane. Tear strength in longitudinal and transverse direction as 60/80N. 22.19.1 3 mm thick sqm 0.024 P/L APP modified prefabricated five layer 3 mm thick water proofing membrane. Tear strength in longitudinal and transverse direction as 300/250N. 22.20.1 3 mm thick sqm 0.036
22.20
430
S.No.
Reference No.
Contents in Brief
431
S.No.
Reference No.
Contents in Brief
432