Sony BE5 Service Mode PDF
Sony BE5 Service Mode PDF
+
(ON SCREEN DISPLAY)
5
(DIGIT 5)
+
(VOLUME +) (TV)
"TT-- " will appear in the top right corner of the screen Other status information will also be displayed. 3. Press the MENU button on the Remote Commander to obtain the menu on the screen.
Software version
4. Press the Blue (Next) or Green (previous) buttons to select the adjustment item from the table. 5. Press the Yellow (+) or Red (-) buttons to change the data as required. 6. Turn off the power to quit the service mode when adjustments are completed.
19
KV-20WS1
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14
Switch 'TT' Mode off. Set picture level to maximum. Set picture level to minimum. Set volume to 35%. Set volume to 50%. Set volume to 65%. Set volume to 80%. Ageing condition (picture max., brightness max.). Shipping condition (Analog values are RESET to factory setting, Prog 1 is selected, TTmode switched off, Vol = 35%). Dummy. No function. Dummy Dummy. Dummy. Dummy. Read factory setting from ROM to NVM - Reads Volume, Brightness, Picture, Hue, Sharpness and Colour values from ROM to the actual used values (Last Power Memory). Save actual used values as reset values. Enable / Disable Sharpness Operation. Dummy. RGB priority. No function. No function. Sub Colour (Pal / Secam Different Stores) Sub Brightness. RGB priority on.
Destination Systems DKE. Destination Systems I/U. Destination System I/I'. Destination BG only. Dummy. No function. Picture level to 50% No function. Audio mute ON. OSD off. Enter G2 adjustment mode. Sub-brightness No function. Re-initialise NVM. Dummy. Re-initialise Geometry settings. Dummy Set NVM testbyte to 44h in NVM. Erase NVM testbyte No function. Toggle 60/100 programs.
15
16 17 18 19 20 21 22 23 24
Note : For Test Modes 41 - 51, it is necessary to ensure that the TV is set to Prog 59.
20
KV-20WS1
DEFLECTION SYSTEM ADJUSTMENT 1. Enter into the service mode. 2. Using the Blue or Green buttons select the Adjust item. 3. Press the Yellow button to enter the adjustment submenu. 4. Select and adjust each item in order to obtain the optimum image. See Note on page 22
VERT, AMPL
V, LINEAR
V, CENTRE Adjustment V size V breth Pin amp Para. tilt V linear Corner corr H size V pos H phase Blue Green Red HV blk 1 HV blk 2 V cent Zwei max zwei min Set 21 32 12 43 42 05 34 00 42 26 32 42 00 00 06 36 18 Range 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 PAR TILT 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 PAR AMP H, CENTRE
AGC ADJUSTMENT 1. Receive a signal of 63dBuV / 75 ohm terminated via the tuner socket. 2. Measure the voltage at AGC TP. 3. Adjust TU101 RV to obtain a voltage of 3.0 0.3V.
IC301
A
- A Board Component Side -
21
KV-20WS1
Notes
Only reported on mains power up. Reported on mains power up or exiting standby. Reported at any time and result in the set reverting to standby mode. Reported at any time and result in the set reverting to audio mute mode.
Note : Deflection System Adjustments should not be carried out whilst using an NTSC (60Hz) signal, or if the signal is unlocked.
OFF
OFF
22