Professional Documents
Culture Documents
Preview Proposed Amendments UBBL 2013
Preview Proposed Amendments UBBL 2013
Remarks
1.
1. Interpretation. In these By-laws, unless the context otherwise requires "dead load" means that static weight of all walls, partitions, floors, roofs and finishes, including all other permanent construction; -None.
Permanent load is used in MS EN 1991-1-1:2010: Actions on Structures Part 1-1: General Actions Densities, Self-weight, Imposed Loads for Buildings. To enable the latest published edition of the relevant MS EN to be applied in these By-laws to replace the British Standard.
NO.
EXISTING PROVISION
Remarks
2.
-None-
3.
-None-
This Part shall apply to the demolition of a To provide a new Part regulating building before reconstruction thereof. any building demolition before reconstruction. 2B. Preparation and submission of demolition plan, etc. (1) Before the demolition is commenced, one copy of the detailed demolition plan together with a copy of the stability report prepared in accordance with MS 2318:2010 (P) shall be submitted to the local authority. (2) The detailed demolition plan shall bear a cerficate by the submitting person as in Form A as set out in the Second Schedule to these By-laws to the effect that the details are in accordance with MS 2318:2010 (P) and that the submitting person accepts full responsibility. To adopt MS 2318:2010 (P): Demolition of Buildings Code of Practice (First Revision) in regards to the details of the demolition plan and the stability report.
Page 2
NO.
4.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
2C. Power of local authority to reject demolition plan and stability report. Notwithstanding paragraph (2) of by-law 2B, the local authority may examine and in so doing may reject any demolition plan or stability report which is not in accordance with MS 2318:2010 (P) and if it rejects such plan or report it may require such submitting person to resubmit a new demolition plan or stability report in respect of the rejected portion.
Remarks
The local authority may examine the plan and require the principal submitting person or submitting person to resubmit a plan.
5.
-None-
or
(1) Notice of the intention to commence or resume the demolition of a building required under subsection (9) of section 70 of the Act shall be made in Form B as set out in the Second Schedule to these Bylaws and shall include particulars of the intended work. (2) If the work is not commenced or resumed on the date given in such notice, a further notice in Form B as set out in the Second Schedule to these By-laws shall be given before the work may be commenced or resumed.
To provide that a notice of the commencement or the resumption of the demolition shall be given to the local authority before the work is carried out.
Page 3
NO.
6.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
2E. Methods of demolition.
Remarks
7.
-None-
The demolition works shall conform to MS To adopt MS 2318:2010 (P) in 2318:2010 (P). regards to the methods of demolition. 2F. Duties of submitting person. (1) The submitting person certifying the To provide the duties plan under paragraph (2) of by-law 2B shall submitting person. be responsible for the proper execution of the demolition works and shall continue to be so responsible until the completion of the demolition works unless (a) with the agreement of the local authority, another submitting person is appointed to take over; or (b) the local authority agrees to accept his withdrawal or replacement at the request of the owner provided that the demolition works has not commenced. (2) Where the local authority agrees to accept the submitting persons withdrawal or replacement under subparagraph (1)(b), the demolition works shall not commence until another submitting person is appointed to take over.
Page 4
of
the
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
(3) Where any submitting person who has submitted the demolition plan has died or become bankrupt or cannot be found or has been deregistered from the register or for any other reason ceased to practice, the owner or occupier shall as soon as practicable appoint another submitting person to act for him and to submit adquate evidence to the local authority of the circumstances.
Remarks
8.
-None-
2G. Exemption from this Part. The local authority may if it deems fit To provide for power to exempt if exempt any minor demolition work from the the nature of the demolition work requirements of this Part. does not warrant the measures provided in this Part.
Page 5
NO.
EXISTING PROVISION
Remarks
9.
(1) All plans for buildings submitted to (1) All plans for buildings submitted to the the local authority for approval in local authority for approval in addition to the addition to the requirements of section requirements of section 70 of the Act shall70 of the Act shall (d) have attached thereto a stamped -Deletedcopy of the relevant site plan approved by the competent planning authority and certified within twelve calendar months preceding the date on which the building plans are deposited unless otherwise exempted under any law relating to planning. 10. 5. Supervision of work. Where under these By-laws any plan, drawing or calculation in relation to any building is required to be submitted by a principal submitting person or submitting person, no erection or continued erection of that building shall take unless that principal submitting person or submitting person or any person duly authorized by him undertakes the supervision of the 5. Supervision of work. (1) Where under these By-laws any plan, drawing or calculation in relation to any building is required to be submitted by a principal submitting person or submitting person, no erection or continued erection of that building shall take place unless that principal submitting person or submitting person or any person duly authorized by him undertakes the supervision of the
This paragraph is proposed to be deleted to facilitate the concurrent processing system implemented at the One-Stop Centre (OSC). The system enables application for planning permission and building plans approval to be submitted to the OSC simultaneousy.
Page 6
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
out, where
Remarks
erection and the setting out, where erection and the setting applicable, of that building. applicable, of that building.
(2) The erection of a building shall be carried out under the fulltime supervision of a construction site supervisor who is acrredited and certified by the Lembaga Pembangunan Industri Pembinaan Malaysia under the Lembaga Pembangunan Industri Pembinaan Malaysia Act 1994 [Act 520]. 11. 8. Plans to be deposited in triplicate. 8. Plans to be deposited in triplicate.
To ensure supervision of work to be carried out by by a person with relevant site supervision experience.
(1) All building plans shall be deposited (1) All building plans shall be deposited in in triplicate or in as many copies as may triplicate or in as many copies as may be be required by the local authority. required by the local authority. (2) One set of the plans shall be on linen (2) One set of the plans shall be returned The linen requirement is dispensed or other equally wear-resistant and after approval. with to allow the usage of any other durable material which, together with dependable medium or material. one other set, shall be retained by the local authority and the third set shall be returned after approval.
Page 7
NO.
12.
EXISTING PROVISION
10. Plans required.
PROPOSED AMENDMENT
10. Plans required.
Remarks
(1) All building plans in respect of any (1) All building plans in respect of any building shall, unless inapplicable, building shall, unless inapplicable, contain contain the following: the following: (a) A site plan showing (iv) where required by the local authority the dimensions of the lot; . 13. 16. Details and structural plans. calculation (a) A site plan showing (iv) where required by the local Dimensions and area of the lot authority the dimensions and provides for a more perfect 2D area of the lot; mesures of the lot. ... .
of 16. Details and calculation of structural plans. (2) The detailed structure plans shall bear a To allow the usage of any other certificate by the submitting person as in dependable medium or material. Form A as set out in the second schedule to these By-laws to the effect that the details are in accordance with there Bylaws and that the submitting person accepts full responsibility.
(2) The detailed structure plans shall be on linen and each copy shall bear a certificate by the submitting person as in Form A as set out in the second schedule to these By-laws to the effect that the details are in accordance with there By-laws and that the submitting person accepts full responsibility.
Page 8
NO.
EXISTING PROVISION
Remarks
14.
(6) The requirements of this by-law shall apply to any of the following buildings or any part thereof: (a) offices, banks, post offices, shops, department stores, supermarkets and other administrative and commercial buildings; except shophouses existing at the commencement of this by-law; (b) rail, road, sea and air travel buildings and associated concourses, car parking buildings and factories; (c) hospitals, medical centres, clinics and other health and welfare buildings; (d) restaurants, concert halls, threatres, cinemas, conference buildings, community buildings,
Page 9
NO.
EXISTING PROVISION
swimming pools, sports buildings and other refreshment, entertainment and recreation buildings; (e) religious buildings; (f) schools, colleges, universities, zoos, museums, art galleries, libraries, exhibition buildings and other educational, cultural and scientific buildings; and (g) hostels, hotels and other residential building other than single family private dwelling houses.
PROPOSED AMENDMENT
Remarks
15.
38. Width of footway. (1) The width of any verandah-way or uncovered footway shall not be less than 2.25 metres but piers or columns to a maximum depth of 600 millimetres from the boundary of the street may be permitted on such verandah-way or footway.
38. Width of footway. (1) The width of any verandah-way or The reduction of the measurement uncovered footway shall not be less than to 7 feet or 2.10 metres is in line 2.10 metres but piers or columns to a with the current practice. maximum depth of 600 millimetres from the boundary of the street may be permitted on such verandah-way or footway.
Page 10
NO.
16.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
38A. Energy efficiency in buildings.
Remarks
(1) New or renovated non-residential To facilitate the efficient use of buildings with air-conditioned space energy, as requested by the Ministry exceeding 4,000 square metres shall be of Energy, Green Tecnology and Water (KeTTHA). (a) designed to meet the requirements of MS 1525 with regards to the Overall Thermal Transfer Value (OTTV) and the Roof Thermal Transfer Value (RTTV); and (b) provided with an Management System. Energy
(2) The roof for all buildings (residential and non residential) shall not have a thermal transmittance (U-value) greater than (a) 0.4 W/m2K for Light (under 50 kg/m2) weight roof; and 0.6 W/m2K for Heavy (above 50 kg/m2) weight roof,
(b)
Page 11
NO.
17.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
38B. Protection of building structures against lightning strikes.
Remarks
(1) The assessment of risks and provision To ensure proper lightning strikes of measures to protect building structures protection to be installed for public against lightning strikes shall comply with safety. the requirements set out in MS IEC 62305. (2) For the purpose of paragraph (1), MS IEC means the latest published edition of the Malaysian Standard which is identical to the International Electrotechnical Commission Standard. 18. 39. Natural lighting and ventilation. (1) Every room designed, adapted or used for residential, business or other purposes except hospitals and schools shall be provided with natural lighting and natural ventilation by means of one or more windows having a total area of not less than 10% of the clear floor area of such room and shall have openings capable of allowing a free uninterrupted passage of air of not less than 5% of such floor area. 39. Natural lighting and ventilation. (1) Every room designed, adapted or used for residential, business or other purposes except hospitals and schools shall be provided with natural lighting and natural ventilation by means of one or more windows having a total area of not less than 10% of the clear floor area of such room and not less than half out of this 10% floor area shall have openings capable of allowing a free uninterrupted passage. There are no substantive changes and the proposed amendment is only to clarify the technical meaning of this provision.
Page 12
NO.
EXISTING PROVISION
(2) Every room used for the accommodation of patients in a hospital shall be provided with natural ventilation by means of one or more windows having a total area of not less than 15% of clear floor area of such room and shall have openings capable of allowing a free uninterrupted passage of air of not less than 10% of such floor area. (3) Every room used for the purpose of conducting classes in a school shall be provided with natural lighting and natural ventilation by means of one or more windows having a total area of not less than 20% of clear floor area of such rooms and shall have openings capable of allowing a free uninterrupted passage of air of not less than 10% of such floor area.
PROPOSED AMENDMENT
(2) Every room used for the accommodation of patients in a hospital shall be provided with natural lighting and natural ventilation by means of one or more windows having a total area of not less than 15% of clear floor area of such room and not less than two third out of this 15% floor area shall have openings capable of allowing a free uninterrupted passage. (3) Every room used for the purpose of conducting classes in a school shall be provided with natural lighting and natural ventilation by means of one or more windows having a total area of not less than 20% of clear floor area of such rooms and not less than half out of this 20% floor area shall have openings capable of allowing a free uninterrupted passage of air. ventilation and air-
Remarks
19.
41. Mechanical ventilation and air- 41. Mechanical conditioning. conditioning. (1)Where permanent mechanical ventilation or air-conditioning is intended, the relevant building by-laws relating to natural ventilation, natural lighting and heights of rooms may be waived at the discretion of the local authority.
(1) Where permanent mechanical ventilation or air-conditioning is intended, the relevant building by-laws relating to natural ventilation, natural lighting and height of rooms shall not apply.
To exclude the application of the relevant provisions of these by-laws, instead of having to make application to the local authority for exemption.
Page 13
NO.
EXISTING PROVISION
(2) Any application for the waiver of the relevant by-laws shall only be considered if in addition to the permanent air-conditioning system there is provided alternative approved means of ventilating the air-conditioned enclosure, such that within half an hour of the air-conditioning system failing, not less than the stipulated volume of fresh air specified hereinafter shall be introduced into the enclosure during the period when the air-conditioning system is not functioning.
PROPOSED AMENDMENT
(2) Permanent air-conditioning system shall be provided with alternate means of ventilating the air-conditioned enclosure, such that within half an hour of the airconditioning system failing, not less than the stipulated volume of fresh air specified hereinafter shall be introduced into the enclosure during the period when the airconditioning system is not functioning.
Remarks
Page 14
NO.
EXISTING PROVISION
Remarks
20.
54. General requirements of loading. (1) In determining, for the purposes of these By-laws, the loads to which any building will be subjected, the dead and imposed loads and wind loads shall be calculated in accordance with this Part: .
(1) In determining, for the purposes of Consequential amendment to bythese By-laws, the loads to which any law 1: Interpretation. building will be subjected, the permanent and imposed loads and wind loads shall be calculated in accordance with this Part: .
(2) In determining, for the purposes of (2) In determining, for the purposes of this this Part, the loads to which a building Part, the loads to which a building will be will be subjected subjected (a) dead loads shall be calculated in accordance with BSCP 3 Chap. V Part 1 or as provided hereinafter in this Part; (b) imposed loads shall be calculated in accordance with BSCP 3 Chap. V Part 1 or as provided hereinafter in this Part: Provided that, if any actual imposed load will exceed or is likely to exceed the load so calculated that actual load shall be substituted for the load so (a) permanent loads shall be calculated To adopt MS EN 1991-1-1 to in accordance with MS EN 1991-1-1 replace the British Code of Practice. or as provided hereinafter;
(b) imposed loads shall be calculated in accordance with MS EN 1991-1-1 or as provided hereinafter; Provided that, if any actual imposed load will exceed or is likely to exceed the load so calculated that actual load shall be substituted for the load so
Page 15
NO.
EXISTING PROVISION
calculated; and (c) wind loads shall be calculated in accordance with BSCP 3 Chap. V Part: Provided that (aa) in no case shall the factor S 3 be taken as less than 1; and (bb) if a building falls outside the range of those for which that code gives them forces and pressure coefficients values shall be used which are appropriate in relation to that building; having regard to its construction, size, proportions, shape, profile and surface characteristics. (3) Advice on appropriate wind velocities applicable to a particular locality to which the building is to be located shall, whenever possible be obtained from the local meteorological office.
PROPOSED AMENDMENT
calculated; and
Remarks
(c) Wind loads shall be calculated in To adopt MS 1553 to replace the accordance with MS 1553. British Code of Practice, and reference to details shall be made to the Standard.
-Deleted-
Page 16
NO.
21.
EXISTING PROVISION
55. Dead and imposed loads.
PROPOSED AMENDMENT
55. Permanent and imposed loads.
Remarks
(1) The provisions of this Part relating to (1) The provisions of this Part relating to Consequential amendment to bydead and imposed loads shall apply to permanent and imposed loads shall apply law 1: Interpretation. . to . (2) The dead and imposed loads provided hereinafter shall be in addition to and not in substitution of provision relating to . 22. 56. Dead loads calculated weights of materials used. (2) The permanent and imposed loads provided hereinafter shall be in addition to and not in substitution of provision relating to .
from 56. Permanent loads calculated from weights of materials used. (1) Permanent loads shall be calculated To adopt MS EN to replace the from unit weight given in accordance with British Standard and the Fourth MS EN 1991-1-1 or from the actual known Schedule to these by-laws. weights of the materials used.
(1) Dead loads shall be calculated from unit weight given in BS 648 or from the actual known weights of the materials used.
(2) Typical values for commonly used (2) Typical values for commonly used materials are laid out in the Fourth materials are laid out in MS EN 1991-1-1. Schedule to these By-laws.
Page 17
NO.
23.
EXISTING PROVISION
57. Weight of partitions. Where partitions are shown in the plans, their actual weights shall be included in the dead load. To provide for partitions where their positions are not shown on the plans, the beams and the floor slabs where these are capable of effective lateral distributions of the load, shall be designed to carry, in addition to other loads, a uniformly distributed load per square metre of not less than one third of the weight per metre run of the finished partitions, but not less than 1kN/m2 (102kgf/m2) if the floor is used for office purposes.
PROPOSED AMENDMENT
57. Weight of partitions. Where partitions are shown in the plans, their actual weights shall be included in the permanent load. To provide for partitions where their positions are not shown on the plans, the beams and the floor slabs where these are capable of effective lateral distributions of the load, shall be designed to carry, in addition to other loads, a uniformly distributed load per square metre of not less than one third of the weight per metre run of the finished partitions, but not less than 1kN/m2 if the floor is used for office purposes.
Remarks
Consequential amendment to bylaw 1: Interpretation.
To delete 102kgf/m2 because this metric measurement is no longer referred to in the current practice.
24.
58. Contents of tanks and other 58. Contents receptacles. receptacles. The weight of tanks and other receptacles and of their contents shall be treated as dead loads; account shall be taken of the load conditions when a tank or receptacle is full and when it is empty.
of
tanks
and
other
The weight of tanks and other receptacles Consequential amendment to byand of their contents shall be treated as law 1: Interpretation. permanent loads; account shall be taken of the load conditions when a tank or receptacle is full and when it is empty.
Page 18
NO.
25.
EXISTING PROVISION
59. Imposed floor loads.
PROPOSED AMENDMENT
59. Imposed floor loads.
Remarks
(1) The loads appropriate to the different All Imposed floor loads shall be calculated To adopt the MS EN 1991-1-1. uses to which the parts of a building or in accordance with MS EN 1991-1-1. structure may be put are as specified in the Fourth Schedule to these By-laws. (2) The distributed loads specified therein are equivalent to uniformly distributed static loads per square metres of plan area and provide for the normal effects of impact and acceleration, but not for any special concentrated loads. (3) All floor slabs shall be designed to carry the appropriate distributed or concentrated imposed load whichever produces the greater stresses in the part of the floor slab under consideration. (4) In the design of floor slabs, concentrated loads shall be considered to be applied in the positions which produce the maximum stresses and, where deflection is the design criterion, in the positions which produce maximum deflections.
Page 19
NO.
EXISTING PROVISION
(5) The concentrated imposed load need not be considered where the floor slabs are capable of effective lateral distribution of this load. (6) All beams shall be designed to carry the distributed load appropriate to the uses to which they are put. (7) Beams, ribs and joists spaced at not more than one metre centres may be designed as floor slabs. (8) Where in the Fourth Schedule to these By-laws no values are given for concentrated load, it may be assumed that the tabulated distributed load is adequate for design purposes.
PROPOSED AMENDMENT
Remarks
26.
60. Mechanical stacking. Where there is the possibility of the use of mechanical stacking machines, such as fork lift trucks, special provision shall be made in the design of the floors.
60. Mechanical stacking. Where there is the possibility of the use of To adopt the MS EN 1991-1-1. mechanical stacking machines, such as fork lift trucks, special provision shall be made in the design of the floors in accordance with MS EN 1991-1-1.
Page 20
NO.
27.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
61. Imposed loads on ceilings, 61. Imposed loads on ceilings, skylights skylights and similar structures. and similar structures. (1) The support of ceilings (other than false ceilings), ribs of skylights, frames and covering (other than glazing) if access hatches and similar structures shall be designed for the following loads: (a) 0.25kN/m2 (25.5kgf/m2) distributed uniformly over the whole area of area supported; and (b) 0.9kN (91.8kgf) concentrated over a length of 125 millimetres or, in the case of coverings, over a square of 125 millimetres side so placed as to produce maximum stresses in the affected members. (2)Where any member will in no circumstances need to support the weight of a man, the concentrated load provided in paragraph (1)(b) above may be neglected. Then concentrated load should be considered to act at the same time as the distributed load and may be
Page 21
(1) The support of ceilings (other than false To adopt the MS EN 1991-1-1. ceilings), ribs of skylights, frames and covering (other than glazing) of access hatches and similar structures shall be designed in accordance with MS EN 19911-1.
NO.
EXISTING PROVISION
treated as a short term load. (3) For the purpose of this by-law false ceiling means a ceiling which is built with a space between it and the structure above and which satisfies at least one of the following conditions relating to access to that space: .
PROPOSED AMENDMENT
(2) For the purpose of this by-law false ceiling means a ceiling which is built with a space between it and the structure above and which satisfies at least one of the following conditions relating to access to that space: .
Remarks
28.
62. Reductions in total imposed floor 62. Reductions in total imposed floor loads. loads. (1) Except as provided for in paragraphs (2) and (3), the reduction in assumed total imposed floor loads given in the Table 1 below may be taken in designing columns, piers, walls, their supports and foundations. TABLE 1: REDUCTION IN TOTAL DISTRIBUTED IMPOSED FLOOR LOADS Number of floors, including the roof, carried by member under consideration Reduction in total distributed imposed load on all floors carried by the member under consideration
Page 22
The reduction in assumed total imposed To adopt the MS EN 1991-1-1. floor loads given in MS EN 1991-1-1 may be taken in designing columns, piers, walls, their supports and foundations.
NO.
EXISTING PROVISION
1 2 3 4 5 to 10 over 10 % 0 10 20 30 40 50
PROPOSED AMENDMENT
Remarks
(2) For the purposes of this by-law, a roof may be regarded as a floor. For factories and workshops design for imposed load of 5kN/m2 (510kgf/m2) or more, the reductions shown in the Table 1 may be taken provided that the loading assumed is not less than it would have been if all floors had been designed for 5k/N/m2 (510kgf/m2) with no reductions. (3) Where a single span of a beam or girder supports not less than 46 square metres of floor at one general level, the imposed load may in the design of the beam or girder be reduces by 5% or each 46 square metres supported, subject to a maximum reduction of 25%. This reduction. or that given in the Table 1, whichever is greater, may be taken into account in the design of columns of other types of members supporting such a beam.
Page 23
NO.
EXISTING PROVISION
(4) No reduction shall be made for only plant or machinery which is specifically allowed for or for buildings for storage purposes, warehouse, garage, and those office areas which are used for storage and filling purposes.
PROPOSED AMENDMENT
Remarks
29.
(1) For the purpose of this by-law all For the purpose of this by-law, imposed To adopt the MS EN 1991-1-1. slopes are measured from the horizontal, roof load shall be designed in accordance all loads are applied vertically and the with MS EN 1991-1-1. 125 millimetres and 300 millimetres squares are measured on the roof slope. (2) On flat roofs and sloping roofs up to and including 10, where access (in addition to that necessary for cleaning and repair) is provided to the roof, allowance shall be made for an imposed load of 1.5kN/m2 (153kgf/m2) measured on plan, or a load of 1.8kN (184kgf) concentrated on a square with a 300 millimetres side, measured in the plane of the roof, whichever produces the greater stresses in the part of the roof under considerations. (3) On flat roofs and sloping roofs up to
Page 24
NO.
EXISTING PROVISION
and including 10 where no access is provided to the roof except for maintenance, allowance shall be made for an imposed load of 0.25kN/m2 (25.5kgf/m2) measured in the plane of the roof, or a vertical load of 0.9kN (91.8kgf) concentrated on a square with 1225 millimetres side, measured in the plane of the roof, whichever produces the greater stresses in the part of the roof under consideration. (4) On surfaces where accumulation of rain water is possible the loads due to such accumulation of water and the imposed loads for the roofs as given above shall be considered separately and the more critical of the two shall be adopted in the design. (5) On roofs with a slope greater than 10, and with no access provided to the roof (other than that necessary for cleaning and repair), the following imposed loads shall be provided: (a) for a roof-slope of 30 or less 0.25kN/m2 (25.5kgf/m2) measured on plane or a vertical load of 0.9kN (91.8kgf)
PROPOSED AMENDMENT
Remarks
Page 25
NO.
EXISTING PROVISION
concentrated on a square with a 300 millimetres side, whichever produces the greater stress. (b) for a roof slope of 75 or more no allowance is necessary. For roof slopes between 30 and 75, the imposed load to be allowed for may be obtained by linear interpolation between 0.25kN/m2 (25.5kgf/m2) for a 30 roof slope and nil for a 75 roof slope. Note: = degrees
PROPOSED AMENDMENT
Remarks
30.
The imposed load on a curved roof shall The imposed load on a curved roof shall be To adopt the MS EN 1991-1-1. be calculated by dividing the roof into not calculated in accordance with MS EN 1991less than five equal segments and by 1-1. then calculating the load of each, appropriate to its mean slope, in accordance with paragraphs (2) and (3) of by-law 63.
Page 26
NO.
31.
EXISTING PROVISION
65. Roof coverings. To provide for loads incidental to maintenance, all roof coverings, other than glazing, at a slope less than 45 shall be capable of carrying a load of 0.9kN (91.8kgf) concentrated on any square with a 125 millimetres side, measured in the plane of the roof.
PROPOSED AMENDMENT
65. Roof coverings.
Remarks
To provide for loads incidental to To adopt the MS EN 1991-1-1. maintenance, all roof coverings, other than glazing, shall be in accordance with MS EN 1991-1-1.
32.
67. Amount of suspended load. Any panel point of the lower chord of such roof trusses or any point of such other primary structural members supporting roofs over garages, manufacturing or storage floors shall be capable of carrying safely a suspended concentrated load of not less than 9.0kN (918kgf) in addition to the imposed load on the roof.
67. Amount of suspended load. Any panel point of the lower chord of such To adopt the MS EN 1991-1-1. roof trusses or any point of such other primary structural members supporting roofs over garages, manufacturing or storage floors shall be designed in accordance with MS EN 1991-1-1.
33.
(3) In the absence of sufficient data for (3) In the absence of sufficient data for To adopt the MS EN 1991-1-1. such calculation, the increase in the such calculation, the increase in the imposed loads shall be as follows: imposed loads shall be in accordance with MS EN 1991-1-1.
Page 27
NO.
EXISTING PROVISION
Structure Increase in imposed load (per cent) 100
PROPOSED AMENDMENT
Remarks
For frames supporting lifts and hoists ... For foundation, footways and piers supporting lifts and hoistering apparatus ... For light machinery, shaft or motor units For reciprocating light machinery or power units ...
40
(4) Concentrated imposed loads including impact and vibrating effects which may arise due to installed machinery shall be considered and provided for in the design. In any event the increase in imposed loads shall not be less than 20%.
(4) Concentrated imposed loads including impact and vibrating effects which may arise due to installed machinery shall be considered and provided for in the design. In any event the increase in imposed loads shall not be less than 20% or the minimum standard specified in the MS EN 1991-1-1, whichever is the higher.
Page 28
NO.
34.
EXISTING PROVISION
69. Crane gantry girders. (1) In respect of crane gantry girders, the following allowances shall be deemed to cover all forces set up by vibration, shock from slipping of slings, kinetic action of acceleration and retardation and impact of wheel loads: (a) for loads acting vertically, the maximum static wheel loads shall be increased by 25% for an electric overhead crane and 10% for a hand-operated crane; (b) the horizontal force acting transverse to the rails shall be taken as the following percentage of the combined weight of the cab and the load lifted: (i) 10% for an electric overhead crane; and (ii) 5% for crane. a hand-operated
PROPOSED AMENDMENT
69. Crane gantry girders.
Remarks
In respect of crane gantry girders, all forces To adopt the MS EN 1991-1-1. set up by vibration, shock from slipping of slings, kinetic action of acceleration and retardation and impact of wheel loads shall be designed in accordance with MS EN 1991-1-1.
NO.
EXISTING PROVISION
considering the lateral rigidity of the rails and their fastenings; (c) horizontal forces acting along the rails shall be taken at the following percentages of the static wheel loads which can occur on the rails: (i) 10% for an electric overhead crane; and (ii) 5% for crane. a hand-operated
PROPOSED AMENDMENT
Remarks
(2) The forces specified in paragraph (1) above shall be considered as acting at the rail level and being appropriately transmitted to the supporting system. (3) Gantry girders and their vertical supports shall be designed on the assumption that either of the horizontal forces specified in paragraph 1 may act at the same time as the vertical load. (4) The provisions of paragraphs (1), (2) and (3) shall apply only to a single crane operation and to simple forms of crane gantry construction and separate
Page 30
NO.
EXISTING PROVISION
provisions shall be provided for in the calculation in respect of heavy cranes, high-speed operation or multiple crane on a single gantry.
PROPOSED AMENDMENT
Remarks
35.
70. Parapets and balustrades. Parapets and balustrades shall be designed for the minimum loads as provided in Table 2 below. The minimum loads are expressed as horizontal forces acting at handrail or coping level. TABLE 2: HORIZONTAL LOADS ON PARAPETS AND BALUSTRADES Intensity of horizontal load N/m kgf/m run run Light access stairs, 220 22.4 gangways and the like not more than 600mm wide Light access stairs, 360 36.7 gangways and the like not more than 600mm wide, stairways, landings and balconies, Use
70. Parapets and balustrades. Parapets, balustrades and lower panel of To adopt the MS EN 1991-1-1. cladding or curtain walls shall be designed for the minimum loads in accordance with MS EN 1991-1-1.
Page 31
NO.
EXISTING PROVISION
private and domestic All other stairways, 740 landings and balconies and all parapets and handrails to roof Panic barriers 3,000 75.5
PROPOSED AMENDMENT
Remarks
306.0 71. Vehicle barriers for car-parks. All vehicle barriers including enclosing To adopt the MS EN 1991-1-1. parapets and balustrades shall be designed to withstand the impact force of vehicle in accordance with MS EN 1991-1-1.
36.
71. Vehicle barriers for car-parks. (1) Where a barrier to withstand the force of a vehicle is required for a carpark it shall be designed to withstand a force F uniformly distributed over any length of 1.5 metres where F = 0.5MV2 kN (1000 (0.5 mv2)) kgf ------------------------------------------- c + b ( 9.8 ( c + b)) m = mass of vehicle in kg v = velocity in m/s c = deflexion of the vehicle in mm b = deflexion of the barrier in mm (2) Where the car park has been designed on the basis that vehicles using it will not exceed 2500 kilograms
Page 32
NO.
EXISTING PROVISION
the following values shall be used to determine the force F: m = 1500 kg* v = 4.47 m/s c = 100 mm unless better evidence is available. For a rigid barrier the force appropriate to vehicles up to 2500 kilogrammes shall be taken as 150 kN. *The mass of 1500 kg is taken as being more representative of the vehicle population than the extreme value of 2500 kg. (3) Where the car park has been designed for a vehicle exceeding 2500 kilogrammes the following values shall be used to determine the force F: m = the actual mass of the vehicle for which the car park is designed in kilograms. v = 4.47 m/s. c = 100mm unless better evidence is available. (4) The impact force provided under paragraph (2) or (3) above shall be
PROPOSED AMENDMENT
Remarks
Page 33
NO.
EXISTING PROVISION
considered to act at bumper height. In the case of car parks intended for motor cars not exceeding 25010 kilogrammes this shall be taken as 375 millimetres the floor level. (5) Barriers to access ramps of car parks shall be designed to withstand one half* of the force determined in paragraph (2) or (3) above acting at a height of 610 millimetres above the ramp. Opposite the ends of straight ramps intended for downyard travel which exceed 20 metres in lenght the barrier shall be designed to withstand twice +the force determined in paragaraph (2) or (3) above acting at the height of 610 millimetres above the ramp. (6) The recommendations in these Bylaws may be used to form the basis of designs either within or beyond the usual serviceability limits of materials. NOTES: * The mass of 1500 kg is taken as being more representative of the vehicle population than the extreme value of 2500 kg.
PROPOSED AMENDMENT
Remarks
Page 34
NO.
+
EXISTING PROVISION
The force in the paragraph (5) above is only half that of paragraph (2) or (3) because although the speed of vehicles may be greater the angle of impact is likely to be less. At the ends of straight ramps however not only is the speed likely to be greater but the angle of impact will also be greater so that the barrier must withstand a greater force is therefore double that given in paragraph (2) or (3).
PROPOSED AMENDMENT
Remarks
37.
72. Basement walls and floors. (3) In the design of basement floors and similar structures underground, the upward pressure of water, if any, shall be taken as the full hydrostatic pressure applied over the entire area.
72. Basement walls and floors. (3) In the design of basement floors and To include all type of underground similar structures underground, the upward pressure. pressure of water, if any, shall be taken as the full hydrostatic pressure applied including any artesian pressure over the entire area. 73. Foundations. (1) The earthworks, the underground To ensure a proper building works and the foundations for the investigation is carried out. building shall be designed based on the field and laboratory tests of a proper site investigation. The tests are to be initiated and supervised by a Professional Engineer site
38.
Page 35
NO.
EXISTING PROVISION
(1) The foundations of a building shall (a) safely sustain and transmit to the ground the combined dead load, imposed load and wind load in a such manner as not to cause any settlement beyond the limits designed for or other movement which would impair the stability of, or cause damage to, the whole or any part of the building or of the any adjoining building or works; (b) be taken down to such a depth, or be so constructed, as to safeguard the building against damage by swelling and shrinking of the subsoil; and (c) be capable of adequately resisting any attack by sulphates or any other deleterious matter present in the subsoil. (2) The requirements of paragraph (1) shall be deemed to be satisfied if the foundations of a building are constructed in accordance with the relevant
PROPOSED AMENDMENT
with the relevant geotechnical experience. (2) The foundations of a building shall
Remarks
(a) safely sustain and transmit to the Consequential amendment to byground the combined permanent law 1: Interpretation. load, imposed load and wind load in a such manner as not to cause any settlement beyond the limits designed for or other movement which would impair the stability of, or cause damage to, the whole or any part of the building or of the any adjoining building or works; (b) be taken down to such a depth, or To cover any other causes of soil be so constructed, as to safeguard movement. the building against damage by soil settlement and movement; and (c) be capable of adequately resisting any attack by sulphates or any other deleterious matter present in the subsoil.
(3) The requirements of paragraph (2) shall To adopt MS EN 1997. be deemed to be satisfied if the foundations of a building are designed and constructed in accordance with MS EN 1997.
Page 36
NO.
EXISTING PROVISION
recommendation of the BSCP 2004 Foundations.
PROPOSED AMENDMENT
Remarks
39.
74. Foundations of buildings not exceeding four storeys. If the foundations form part of a building other than a factory or storage building, having not more than four storeys the requirements of by-law 73 shall be deemed to be satisfied if such foundations are constructed in accordance with BSCP 101 Foundations and Substructures for NonIndustrial Buildings not more than Four Storeys.
-Deleted-
40.
75. Reinforced concrete foundations. The requirements of by-law 73 shall be deemed to be satisfied as to such part of any foundation as is constructed of reinforced concrete if the work complies with BSCP 110 The Structural Use of Concrete, BSCP 114, BSCP 115 or BSCP 116, where applicable.
75. Reinforced concrete foundations. Reinforced concrete foundation shall be To adopt the specifed Standards. designed and constructed in accordance with MS EN 1990, MS EN 1991 and MS EN 1992.
Page 37
NO.
41.
EXISTING PROVISION
76. Strip foundations. If the foundations of a building are constructed as strip foundations of plain concrete situated centrally under the walls, the requirements of by-law 74 shall be deemed to be satisfied if (a) there is no made ground or wide variation in the type of subsoil within the loaded area and no weaker type of soil exists below the soil on which the foundations rest within such a depth as may impair the stability of the structure; (b) the width of the foundation is not less than the width specified in the Fourth Schedule to these By-laws;
PROPOSED AMENDMENT
-Deleted-
Remarks
This provision is no longer relevant in the current practice.
(c) the concrete is composed of cement and fine and coarse aggregate conforming to BS 882 and is of a nominal mix not learner than 50 kilogrammes cement: 0.3 cubic metre all-in aggregate; (d) the thickness of the concrete is not less than its projection from the base of the wall or footing and is in
Page 38
NO.
(e)
EXISTING PROVISION
no case less than 150 millimetres; where the foundations are laid at more than one level, at each change of level, the higher foundations extend over the unite with the lower foundations for a distance not less than the thickness of the foundations and in no case less than 300 millimetres; and
PROPOSED AMENDMENT
Remarks
(f) where there is a pier, buttress or chimney forming part of a wall, the foundations project beyond the pier, buttress or chimney on all sides to at least the same extent as they project beyond the wall. 42. -None76A. Buildings on hill slopes. Every building to be constructed on hill To be in line with the current slopes shall comply with any planning engineering practice. requirement as the local authority may determine.
Page 39
NO.
43.
EXISTING PROVISION
77. Brick footings. (1) Where brick footings are provided in the foundations of a wall, they shall be in regular off-sets of 50 millimetres wide and the height from the bottom of such footings to the base of the wall shall be equal to at least two-thirds of the thickness of the wall at its base. Wherever possible, the bricks in the footings shall be laid as headers. (2) Brick footings in the foundations of a wall may be omitted if allowance is made for such omission in the thickness of the concrete foundations for the wall. (3) Where in the opinion of the principal submitting person or submitting person ground conditions are favourable, the foundations for non-load bearing internal walls may be formed by increasing the depth of the concrete floor slabs under such internal walls.
PROPOSED AMENDMENT
-Deleted-
Remarks
This provision is no longer relevant in the current practice.
Page 40
NO.
44.
EXISTING PROVISION
78. Foundations drains. below invert
PROPOSED AMENDMENT
of 78. Foundations below invert of drains.
Remarks
(1) When a building or part of a building is erected at a distance from the centre of a drain less than the depth of the drain, except where the whole of such building is carried on piles other than timber piles, the bottom of the foundation of such building or part thereof shall be stepped down within an angle of 45 so that the bottom of the foundation of that part of the building situated within the aforesaid distance shall be at least 450 millimetres below the drain invert. (2) For the purpose of paragraph (1) of by-law 77, in framed building, the foundations shall be deemed to be foundations under the load-bearing columns. 45.
Within a distance not less than the depth of Restructuring of the sentences to a drain measured from the closer edge of give clearer understanding. the drain, no part of a building shall be erected with its substructure foundation level higher than 450 millimetres below the drain invert level, unless the whole of such building is carried on piles other than timber piles.
79. Foundations under external and 79. Foundations under external and party walls. party walls. Where an external wall is built against another external wall or against a party wall, the widths of concrete foundations specified in the Fourth Schedule to these By-laws shall be modified accordingly. Where an external wall is built against To specify the necessary another external wall or against a party wall requirement for foundations under of an adjacent building lot, the extent of external and party walls. concrete foundations shall not extend beyond its own lot boundary
Page 41
NO.
46.
EXISTING PROVISION
80. Structure above foundations. (1) The structure of a building above the foundations shall be designed and constructed to safety sustain and transmit to the foundations the combined dead and imposed loads and wind loads without such deflection or deformation as will impair the stability of, or cause damage to, the whole or any part of the building. (2) The requirements of paragraph (1) shall be deemed to be satisfied if the design and construction of the structure or part of the sructure complies with the following Codes of Practice of Standard Specifications: BS 449 The Use of Structural Steel in Building; BSCP 110 The Structural Use of Concrete; BSCP 111 Structural Recommendations for Load Bearing Walls; BSCP 114 Sructural Use of Reinforced Concrete in Building; BSCP 115 The Structural Use of Prestressed Concrete in Buildings;
PROPOSED AMENDMENT
80. Structure above foundations.
Remarks
(1) The structure of a building above the Consequential amendment to byfoundations shall be designed and law 1: Interpretation. constructed to safety sustain and transmit to the foundations the combined permanent and imposed loads and wind loads without such deflection or deformation as will impair the stability of, or cause damage to, the whole or any part of the building.
(2) The requirements of paragraph (1) shall To replace the British Standards be deemed to be satisfied if the design and and Codes of Pratice with MS EN. construction of the structure or part of the structure complies with the following Standards: MS EN 1990 Basis of Structural Design; MS EN 1991 Actions on structures; MS EN 1992 Design of concrete structures; MS EN 1993 Design of steel structures; MS EN 1994 Design of composite steel and concrete structures; MS EN 1995 Design of timber structures; MS EN 1996 Design of masonry structures; MS EN 1998 Design of structures for earthquake resistance; and
Page 42
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
BSCP 116 The Structural Use of MS EN 1999 Design of aluminum Precast Concrete; structures. BSCP 117 Composite Construction in Structural Steel and Concrete; BSCP 118 The Structural Use of Aluminium; BSCP 2007 Design and Construction of Reinforced and Prestressed Concrete Structure for the Storage of Water and other Aqueous LIquids; BS 5337 The Structural Use of Concrete for Retaining Aqueous Liquids; and MSCP The Sructural Use of Timbers.
Page 43
NO.
48.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
83. Protection against soil erosion, 83. Protection against soil erosion, etc. etc. (1) All slopes in and around buildings shall Protection should not be limited to (1) All air-wells and open spaces in and be suitably protected against soil erosion air-wells and open spaces, but to all around buildings shall be suitably and slope failures and shall be monitored slopes in and around a building. protected against soil erosion. and maintained regularly. 84. Prevention of dampness. 84. Prevention of dampness. More relevant in engineering practice. the current
49.
(3) Every brick or masonry wall of a (3) Every wall of a building founded on building founded on strip footings shall foundation shall be provided with a damp be provided with a damp proof course proof course which shall be which shall be (b) beneath the level of the (b) beneath the level of the underside underside of the lowest of the lowest portion of the ground timbers of the ground floor floor resting on the wall, or where resting on the wall, or where the ground floor is a solid floor, not the ground floor is a solid floor, higher than level of the upper not higher than level of the surface of the concrete or other upper surface of the concrete similar solid material forming the or other similar solid material structure of the floor. forming the structure of the floor.
To cover whatever material used for construction of the lowest portion of the ground floor.
Page 44
NO.
50.
EXISTING PROVISION
86. Party walls. (1) All party walls shall generally be of not less than 200 millimetres total thickness of solid masonry or insitu concrete which may be made up of two separate skins each of not less than 100 millimetres thickness if consctructed at different times: Provided that in multi-storeyed flats and terrace houses of reinforced concrete or of protected steel framed construction having floors and roofs constructed to the requirements of these By-laws, the party wall thereof shall not be less than 100 millimetres total thickness. (2) Party walls in single storeyed houses may be in load-bearing 100 millimetres solid masonry or insitu concrete provided the requirements of Part V, VI and VII of these By-laws are complied with. (3) All party walls shall be carried above the upper surface of the roof to a distance of not less than 230 millimetres at right angles to such upper surface.
PROPOSED AMENDMENT
-Deleted-
Remarks
By-law 141: Separating walls has already provided the necessary fire requirements served to prevent the spread of fire from one separate unit of house to another. As such the Fire Authority will only make reference to by-law 141.
Page 45
NO.
EXISTING PROVISION
(4) Other non-combustible materials may be used for party walls provided the requirements of Part V, VI and VII of these By-laws are complied with.
PROPOSED AMENDMENT
Remarks
51.
87. Openings in party walls (1) Openings may be made or left in a party wall if(a) such openings may be made with the consent of and in accordance with the requirements of the local authority; and (b) the owners of the properties concerned give written permission. (2) Every opening in a party wall shall be solidly built up with brick or stonework to the full thickness of the party wall and properly bonded therewith when the use of such opening is discontinued. -DeletedConsequential amendment to bylaw 86.
Page 46
NO.
52.
EXISTING PROVISION
88. Recess.
PROPOSED AMENDMENT
88. Recess.
Remarks
Where a recess is made in an external Where a recess is made in an external Consequential amendment to bywall or a party wall wall law 86. (a) the wall at the back of the recess shall be not less than 100 millimetres thick in an external wall and 200 millimetres thick in a party wall; . 89. Chases. A chase made in a wall for pipes and other service facilities shall leave the wall at the back of the chase not less than 100 millimetres thick in external walls and not less than 100 millimetres thick in a party wall and shall be not wider than 200 millimetres. 54. 92. Projections in brickwork. All projections in brickwork shall be corbelled but gradually and no projection shall extend more than 230 millimetres from the face of any wall unless built in strong cement mortar. -DeletedNot relevant in the engineering practice. current (a) . the wall at the back of the recess shall be not less than 100 millimetres thick in an external wall;
53.
-Deleted-
This provision is redundant as the statement is very general and concern best practice rather than requirement.
Page 47
NO.
55.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
93. Measurement of the length of a 93. Measurement of the length of a wall. wall. For the purposes of these by-laws For the purposes of these by-laws ,,, (ii) piers therein having a (ii) column therein having a dimension Column is more accurate term and it dimension measured parallel measured parallel to the length of includes pier. to the length of the wall of not the wall of not less than twice the less than twice the thickness thickness of the wall and a of the wall and a dimension dimension measured at right measured at right angles to angles to the wall of not less than the wall of not less than three three times the thickness of the times the thickness of the wall. wall.
56.
94. Use of 100 millimetres brickwork and concrete blocks in load-bearing. Walls built of burnt bricks or of cement bricks 100 millimetres in thickness and walls in concrete blocks of a thickness of not less than 100 millimetres may be used for both internal and external loadbearing walls provided they are designed in accordance with by-law 80. -DeletedThis should be covered under the Fire Requirement Part.
Page 48
NO.
57.
EXISTING PROVISION
97. Timber built into party walls. No timber such as joists, beams, wall plates, tile battens and ties shall be built into the thickness of any party wall unless there are not less than 100 millimetres of brickwork or cement between such timbers.
PROPOSED AMENDMENT
-Deleted-
Remarks
This provision is proposed to be shifted to paragraph (4) of by-law 141 because it is the duty of the Fire Authority to ensure this requirement is satisfied.
58.
99. Cooking facilities in residential 99. Cooking facilities buildings. buildings. (1) Every residential building and every floor of a residential building which is or may be separately let for dwelling purposes shall be provided with a kitchen having a properly constructed fireplace with a flue and chimney as may be required by the local authority. (2) The chimney and smoke flue shall be continued up above the roof and shall be of a thickness all round of not less than 100 millimetres of brick or concrete to a height of not less than 1.2 metres above the highest point in the line of junction with the roof. (3) Flues shall be not less than 230 millimetres in diametre and a separate
in
residential
(1) Every residential building and every The Fire Authority does not approve floor of a residential building which is or this pratice. may be separately let for dwelling purposes shall be provided with a kitchen.
(2) Where a common vertical kitchen More relevant in current practice. exhaust riser is provided, the riser shall be continued up to a mechanical floor or roof for discharge to the open, and shall be constructed with fire resisting material of at least 2 hours rating in accordance with BS 476: Part 3. -Deleted-
Page 49
NO.
EXISTING PROVISION
flue shall be provided for each fireplace.
PROPOSED AMENDMENT
Remarks
59.
100. Cooking facilities in quarters. (1) In the case of one room or two room quarters for labourers, artisans or servants, a kitchen not less than 2.32 square metres in floor area may be provided. Such kitchen shall be provided with a properly constructed fireplace, flue and chimney, and shall be adequately lighted and ventilated. (2) Where it is intended to install in any residential building or floor in a residential building as specified in by-law 99 gas, electric or oil cookers for cooking purposes and the plan for such building is endorsed accordingly, fireplaces, flues and chimneys shall not be required. (3) For the purposes of by-laws 99 and 100, the expression "properly constructed fireplaces" means a concrete slab not less than 80 millimetres thick supported on brick or concrete piers with a smoke hood over such concrete slab constructed of
Page 50
-Deleted-
NO.
EXISTING PROVISION
incombustible materials at a height of 1.91 metres from the floor to the lower edge of such smoke hood. The smoke hood shall project 230 millimetres on each side and in front of the slab and shall be constructed with an angle of inclination of not less than thirty degrees.
PROPOSED AMENDMENT
Remarks
60.
103. Timber floors. (1) Where structural timber floors are permissible under these By-Laws they shall be designed of hardwood or of species of timber treated with a suitable wood preservative. (2) All timber floors joists shall be designed in accordance with these Bylaws. (3) All timber trimming joists shall be at least 25 millimetres thickers than the joist of the adjoining floor. -DeletedNot relevant in the engineering practice. current
61.
104. Bearing for joists. (1) All joists shall have at least 100 millimetres bearing on the walls and where supported on corbelled brickwork, such corbelling shall be continuous over-DeletedConsequential amendment to bylaw 103.
Page 51
NO.
EXISTING PROVISION
sailing courses. Separate corbels shall not be allowed.
PROPOSED AMENDMENT
Remarks
(2) No joists shall be built into the thickness of any party wall unless there is at least 100 millimetres of fire resisting material between the sides and end of such timbers. 62. 107. Handrails. 107. Handrails.
(1) Except for staircases of less than 4 (1) Except for staircases of less than 4 risers, all staircases shall be provided risers, all staircases shall be provided with with at least one handrail. at least one handrail. (2) Staircases exceeding 2225 millimetres in width shall be provided with intermediate handrail for each 2225 millimetres of required width spaced approximately equally. 63. 109. Winders. (1) Subject to the provisions of Part VII and VIII of these By-laws spiral staircases may be permitted as a secondary staircase in buildings where the topmost floor does not exceed 12.2 metres in height. (2) Staircases exceeding 2200 millimetres To be in line with the current pratice. in width shall be provided with intermediate handrail for each 2200 millimetres of required width spaced approximately equally. 109. Winders. -DeletedTo explain provision better and to clarify common misinterpretation.
Page 52
NO.
EXISTING PROVISION
(2) Winding staircase may be permitted where they are not used as a required means of egress. 111. Lighting and ventilation of staircases.
PROPOSED AMENDMENT
Winding and spiral staircase shall not form part of the exit route. 111. Lighting staircases. and ventilation of
Remarks
64.
All staircases shall be properly lighted All staircases shall be properly lighted at and ventilated according to the an average illuminance level of not less requirements of the local authority. than 100 lux and ventilated according to the requirements as stipulated under by-laws 198 to 200 of Part VII. 65. 114. Timber roofs. (1) Structural timber for roof construction shall be designed and constructed of timbers of adequate sizes which shall either be in hardwood or, if in other species of timber, shall be treated by a suitable wood preservative. (2) All built-in or concealed roof timbers shall be coated with wood preservative. -Deleted-
To specify the requirement of lighting in this by-law and ventilation under the relevant by-laws under Part VII.
current
Page 53
NO.
66.
EXISTING PROVISION
117. Access to roof space (1) Where the space beneath a roof is enclosed by a ceiling, access to such space shall be provided by means of a trap door at least 0.75 metre in any direction.
PROPOSED AMENDMENT
117. Access to roof space Where the space beneath a enclosed by a ceiling, access space shall be provided by means door at least 600 millimetres direction. -Deleted-
Remarks
roof is 600 milimetres is the acceptable to such and standard size. of a trap in any Not relevant in the current engineering practice.
(2) No verandah-way shall be constructed except to levels approved by the local authority and shall have a cross-fall of 25 millimetres towards the road or drain. 67. 118. Refuse chutes and alternate means for disposal of refuse. (1) All residential buildings which are four storeys and above shall be provided with refuse chutes unless alternate means for the disposal of refuse such as container-based systems, in-sink waste disposal units, Garcheys system and one-site compression systems are installed. (2) Where such alternative means of refuse disposal are installed, they are subject to the approval of the local
Page 54
-Deleted-
Not relevant in current practice. Selection of means of refuse disposal shall not be restricted to a few selected means.
NO.
EXISTING PROVISION
authority. (3) Where refuse chutes are to be provided, the number shall be determined by the local authority. (4) For non-residential buildings, no refuse chutes will be permitted. The removal of refuse and trash in such buildings shall be by way of the service lift or other means to the satisfaction of the local authority. (5) In multi-purpose buildings containing residential accomodation, refuse chutes shall be provided for the residential portions running through the building, but no openings will be permitted where such chutes pass through the nonresidential portions of the building. (6) Other alternate means for the disposal of refuse as stated in paragraph (1) to the local authority may be provided to serve the residential portions of the building.
PROPOSED AMENDMENT
Remarks
68.
construction
of
Page 55
NO.
EXISTING PROVISION
The design and construction of all refuse chutes shall conform to the following requirements: (a) the chute shall be vertical for the whole lenght and shall be constructed with a smoothfinished impervious inner surface; (b) the internal diametre shall not be less than 400 millimetres; (c) adequate ventilation at the top of the chute shall be provided; (d) the chute shall discharge into a suitable metal receptacle or receptacles of not more than 0.95 cubic metre in capacity or as specified by the local authority; (e) openings into any refuse chute shall be fitted with a self-closing and tight-fitting flap or hopper; and (f) openings into refuse chutes shall not be located in any stairway enclosure or corridor, nor in a stairway protected lobby.
PROPOSED AMENDMENT
-Deleted-
Remarks
Consequential amendment to bylaw 118.
Page 56
NO.
69.
EXISTING PROVISION
121. Requirements receptacle chambers. for refuse
PROPOSED AMENDMENT
Remarks
All refuse receptacles shall be housed in a chamber which shall (a) be provided with concrete curbs for the refuse receptacles to stand on;
-Deleted-
(b) be adequately fly and vermin proofed; (c) be connected to and drained by a foul water drain; open to the external air; be lined throughout with glazed tiles; and be located near to a water point. -DeletedConsequential amendment to bylaw 103.
(d) (e)
(f) 70.
122. Access to refuse receptacle chambers. The approach access to the loading point from refuse chute chambers for the removal of refuse vehicles shall be at
Page 57
NO.
EXISTING PROVISION
gradient to enable the refuse vehicles to approach it and shall be to the approval of the local authority: Provided that where direct access to refuse chutes for refuse vehicles is not possible, specific points for storing refuse receptacles shall be provided to the satisfaction of the local authority. 123. Pipes and service ducts. (1) Where ducts or enclosures are provided in any building to accommodate pipes, cables or conduits the dimensions of such ducts or enclosures shall be (a) adequate for the accommodation of the pipes, cables or conduits and for crossings of branches and mains together with supports and fixing; and sufficiently large to permit access to cleaning eyes, stop cocks and other controls there to enable repairs, extensions and modifications to be made to each or all of the service
PROPOSED AMENDMENT
Remarks
71.
-Deleted-
This provision is redundant as it is very general and concern best practice rather than requirement. The local authority does not regulate as long as the pipes and cables are covered and protected.
(b)
Page 58
NO.
EXISTING PROVISION
accommodated. (2) The access openings to ducts or enclosures shall be long enough and suitably placed to enable lengths of pipe to be installed and removed.
PROPOSED AMENDMENT
Remarks
In this Part and Part VIII unless the In this Part and Part VIII unless the context context otherwise requires otherwise requires D.G.F.S. means the Director General of Fire Services, Malaysia or the relevant Fire Authority; dry rising system means a vertical water main which is normally dry, of appropriate size, and fitted with hydrant outlets which can be charged with water by the Fire Authoritys pumps via a fire service inlet and shall comply with BS 3980 and BSCP 402.101; D.G.F.R. means the Director General of To streamline with Fire Services Act Fire and Rescue, Malaysia or the relevant 1988 (Act 341) (reprinted version). Fire Authority; -DeletedThere is no necessity to define the term as there is no confusion as to its understanding in practice. The technical meaning applies.
Page 59
NO.
EXISTING PROVISION
fire alarm installation means an installation capable of warning persons of an outbreak of fire. Such installation must have detectors conforming to the Rules of the Fire Officers Committee for Automatic Fire Alarm Installation, and installed in accordance with BSCP 1019; -None-
PROPOSED AMENDMENT
-Deleted-
Remarks
There is no necessity to define the term as there is no confusion as to its understanding in practice. The technical meaning applies.
Fire Authority means the officer in charge To define the term Fire Authority. of the relevant Fire and Rescue Department or any officer authorized by him in writing; -DeletedThere is no necessity to define the term as there is no confusion as to its understanding in practice. The technical meaning applies.
fire hydrant means an installation of pipes, water tanks, pumps and hydrant outlets in a building to provide a ready means by which a jet of water can be delivered in any part of the building for the purpose of fire fighting and to comply with BSCP 402.101; fire resistance period means the period for which an element will meet the requirements in respect of transmission of heat or resistance to collapse with
fire resistance period means the period For reference to be made to the for which an element will meet the equivalent Malaysian Standard. requirements in respect of transmission of heat or resistance to collapse with passage
Page 60
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
passage of flame when tested in of flame when tested in accordance with accordance with BS 476; Part 1: 1953; MS 1073; "fire resisting" means the construction so designated, including doors, has a minimum standard of fire-resistance of not less than half hour in accordance with the relevant Schedules of these Bylaws or which achieves such standard when tested in accordance with BS 476: Part 8: 1972 except that, in the case of the doors ; "fire resisting" means the construction so For reference to be made to the designated, including doors, has a overall Standard. minimum standard of fire-resistance of not less than half hour in accordance with the relevant Schedules of these By-laws or which achieves such standard when tested in accordance with BS 476 except that, in the case of the doors ;
F.O.C. means Fire Officers Committee of the United Kingdom; hose reel installation means an installation of pipes, water tanks, pumps and hose reels in a building to provide a ready means by which a jet of water can be delivered in any part of the building for the purpose of fire fighting and to comply with BSCP 402.101;
-Deleted-
-Deleted-
There is no necessity to define the term as there is no confusion as to its understanding in practice. The technical meaning applies.
non-combustible shall apply to "non-combustible" shall apply to materials For reference to be made to the materials as specified under BS 476; as specified under BS 476; overall Standard.
Page 61
NO.
EXISTING PROVISION
Part 4 (1970); -None-
PROPOSED AMENDMENT
Remarks
open corridor means a corridor that has This new term is used in by-law 189 wall openings open to the atmosphere and in the Tenth Schedule. primarily for the adequate dissipation of smoke; open structure means a structure that, at This new term is used in the Tenth each level, has wall openings opening to Schedule. the atmosphere; "smoke stop door" means a door or pair of For reference to be made to the doors which when fitted in a frame satisfies equivalent Malaysian Standard. the requirements of MS 1073 as to ... ;
-None "smoke stop door" means a door or pair of doors which when fitted in a frame satisfies the requirements of Section 7 of BS 476: Part 8: 1972 as to ;
sprinkler installation means an installation of water supplies, pump, pipes, valves and delivery points so arranged as to automatically detect a fire and attack it with water, sound an alarm and installed in accordance with the current edition of the F.O.C. Rules for Automatic Sprinkler Installation or other approved standards; wet rising system means any permanently charged vertical water main
-Deleted-
There is no necessity to define the term as there is no confusion as to its understanding in practice. The technical meaning applies.
-Deleted-
NO.
EXISTING PROVISION
installed for firefighting purposes, of an appropriate size, and fitted with connections suitable for use by the Fire Authoritys and to comply with the requirements of BSCP 402.101.
PROPOSED AMENDMENT
Remarks
its understanding in practice. The technical meaning applies.
73.
136. Provisions of compartment walls 136. Provisions of compartment walls and compartment floors. and compartment floors. Any building, other than a single storey building, of a purpose group specified in the Fifth Schedule to these By-laws and which has : Provided that if any building is provided with an automatic sprikler installation which complies with the relevant recommendations of the F.O.C. Rules for Automatic Sprinkler Installation, 29th edition, this by-law has effect in relation to that building as if the limits of dimensions specified are doubled. Any building, other than a single storey building, of a purpose group specified in the Fifth Schedule to these By-laws and which has : Provided that if any building is provided To adopt MS 1910. with an automatic sprikler installation which complies with MS 1910, this by-law has effect in relation to that building as if the limits of dimensions specified are doubled.
Page 63
NO.
74.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
To provide stricter requirements in relation to the extent of subdivision of a building as compartment floors.
137. Floor in building exceeding 30 137. Compartmentation by height. metres in height to be constructed as compartment floor. In any building which exceeds 30 metres in height, any floor which is more than 9 metres above ground floor level which separates one storey from another storey, other than a floor which is either within a maisonette or a mezzanine floor shall be constructed as a compartment floor. (1) In any building not exceeding 30 metres in height, any floor which is more than 9 metres above ground floor level which separates one storey from another storey, other than a floor which is either within a maisonette or a mezzanine floor shall be constructed as a compartment floor. (2) In any building exceeding 30 metres in height, all floors shall be constructed as compartment floors, other than a compartment which is within a residential maisonette which may comprise two storey levels. (3) An atrium shall comply with the requirements of by-law 252A. -None-
-None-
75.
139. Separation of fire risk area. The following areas or uses shall be separated from the other areas of the occupancy in which they are located by fire resisting construction of elements of
139. Separation of fire risk area. (1) The following areas or uses shall be separated from the other areas of the occupancy in which they are located by fire resisting construction of elements of
Page 64
NO.
EXISTING PROVISION
structure of a FRP to be determined by the local authority based on the degree of fire hazard: . -None-
PROPOSED AMENDMENT
structure of a FRP to be determined by the local authority based on the degree of fire hazard: . (2) For hospital and nursing home of Purpose Group II (Institutional), laboratories and kitchens shall not have sleeping accommodation above them and shall form separate compartments from inpatient treatment areas, public areas, staircase and lift discharge areas. 140. Fire appliances access. (1) Accessway shall be provided within the site of a building to enable fire appliances to gain access to the building. Access openings shall also be provided along the external walls of buildings fronting the accessway to provide access into the building for fire fighting and rescue operations. (2) The requirements of accessway shall be as follows: (a) the accessway shall have a minimum width of 6 metres throughout its entire length and shall be able to accommodate the entry
Remarks
This provision is transferred from the existing Note (iv) under the Institutional item of the Tenth Schedule because this requirement is a planning matter (rather than fire protection systems) and therefore should be covered under this Part.
76.
140. Fire appliances access. All buildings in excess of 7000 cubic metres shall abut upon a street or road or open space of not less than 12 metres width and accessible to fire brigade appliances. The proportion of the building abutting the street, road or open space shall be in accordance with the following scale: Volume of building in cubic metre Minimum proportions of perimetre of building one-sixth
To provide more detailed requirements concerning fire applicances access in line with the current fire fighting practice.
7000 to 28000
Page 65
NO.
EXISTING PROVISION
2800 to 56000 56000 to 84000 84000 to 112000 112000 and above one-fourth one-half three-fourths island site
PROPOSED AMENDMENT
and manouvering of fire engine, extended ladders pumping appliances, turntable and hydraulic platforms; (b) the accessway shall be metalled or paved or laid with strengthened perforated slabs to withstand the loading capacity of stationary 30 tonnes fire appliance;
Remarks
(c) the accessway shall be positioned so that the nearer edge shall be not less than 2 metres or more than 10 metres from the centre position of the access opening, measured horizontally; (d) the accessway shall be laid on a level platform or if on an incline, the gradient shall not exceed 1:15. The access road shall be laid on a incline not exceeding a gradient of 1:8.3; (e) the dead-end accessway and fire engine access road shall not exceed 46 metres in length or if exceeding 46 metres, be provided with turning facilities;
Page 66
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
(f) the outer radius for turning of accessway and fire engine access road shall comply with the requirements of the Fire Authority; (g) the overhead clearance of fire engine access road shall be at least 4.5 metres for passage of fire appliances;
Remarks
(h) public roads may serve as accessway provided that the location of such public roads is in compliance with the requirements of distance from access openings as the Fire Authority may specify; and (i) the accessway and the fire engine access road shall be kept clear of obstructions and others parts of the building, plants, trees or other fixtures shall not obstruct the path between the accessway and the access openings. (3) All corners of the accessway shall be marked as follows:
Page 67
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
(a) the marking of corners shall be in contrasting colour to the ground surfaces or finishes; (b) the accessway provided on turfed area shall be marked with contrasting object (preferably reflective) that is visible at night. The markings are to be at an interval not more than 3 metres apart and shall be provided on both sides of the accessway; and (c) a sign post displaying the wordings Fire Engine Access Keep Clear shall be provided at the entrance of the accessway. Size of wordings shall not be less than 50 milimeteres. (4) The proportion of the building in excess of 7000 cubic metres fronting the accessway shall be in accordance with the following scale: Volume of building in cubic metre Minimum proportions of perimetre of building
Remarks
Page 68
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
7000 to 28000 2800 to 56000 56000 to 84000 84000 to 112000 112000 and above one-sixth one-fourth one-half three-fourths island site
Remarks
77.
141. Separating walls. (4) No timber such as joists, beams, wall This paragraph is moved from byplates, tile battens and ties shall be built law 97 because it is a fire into the thickness of any separating wall requirement. unless there are not less than 100 millimetres of brickwork or cement between such timbers. 144. Cladding on external wall. (2) Any cladding on any external wall situated 1.2 metres or more from the relevant boundary shall, if the building is more than 18 metres in height, have a surface complying with the requirements
Page 69
78.
144. Cladding on external wall. (2) Any cladding on any external wall situated 1.2 metres or more from the relevant boundary shall, if the building is more than 18 metres in height, have a surface complying with the requirements
NO.
EXISTING PROVISION
specified for Class O in by-law 204 except that any part of such cladding below the height of 18 metres from the ground may consist of timber of not less than 10 millimetres finished thickness or of a material having a surface which, when tested in accordance with BS 476: Part 6: 1968, has an index of performance not exceeding twenty.
PROPOSED AMENDMENT
Remarks
specified for Class O in by-law 204 except that any part of such cladding below the height of 18 metres from the ground may consist of timber of not less than 10 millimetres finished thickness or of a material having a surface which, when tested in accordance with BS 476, has an For reference to be made to the index of perfomance not exceeding twenty. Standard as a whole.
79.
154. Emergency mode of operation in the event mains power failure. (1) On failure of mains power of lifts shall return in sequence directly to the designated floor, commencing with the fire lifts, without answering any car or landing calls and park with doors open. (2) After all lifts are parked the lifts on emergency power shall resume normal operation: Provided that where sufficient emergency power is available for operation of all lifts, this mode of
Page 70
-Deleted-
This provision is shifted to new bylaw 243A because it concerns about fire protection systems and therefore should be covered under Part VIII.
NO.
EXISTING PROVISION
operation need not apply.
PROPOSED AMENDMENT
Remarks
80.
159. Open stages. Open stages without proscenium walls may be permitted provided suitable protection devices to the satisfaction of the D.G.F.S. are installed.
159. Open stages. Open stages without proscenium walls may Consequential amendment to bybe permitted provided suitable protection law 133: Interpretation. devices to the satisfaction of the D.G.F.R. are installed.
81.
162. Fire doors in compartment walls and separating walls. (5) Fire doors including frames shall be constructed to a specification which can be shown to meet the requirements for the relevant FRP when tested in accordance with section 3 of BS 476: 1951. -DeletedFire door specifications should be provided under by-law 163.
82.
Fire doors conforming to the method of Fire doors including frames shall be To adopt MS 1073. construction as stipulated below shall be constructed in accordance with MS 1073. deemed to meet the requirements of the specified FRP:
Page 71
NO.
EXISTING PROVISION
(a) doors and frames constructed in accordance with one of the following specifications shall be deemed to satisfy the requirements for doors having FRP of half-hour: (i) a single door 900 millimetres wide X 2 100 millimetres high maximum or double doors 1 800 millimetres X 2 100 millimetres high maximum constructed of solid hardwood core of not less than 37 millimetres laminated with adhesives conforming to either BS 745 "Animal Glues", or BS 1204, "Synthetic resin adhesive (phenolic and aminoplastic) for wood" Part 1, "Gap-filling adhesives " or BS 1444, "Cold-setting casein glue for wood", faced both sides with plywood to a total thickness of not less than 43 millimetres with all edges finished with a solid edge strip full width of the door.
PROPOSED AMENDMENT
Remarks
Page 72
NO.
EXISTING PROVISION
The meeting stiles of double doors shall be rabbeted 12 millimetres deep or may be butted provided the clearance is kept to a minimum; (ii) doors may be double swing provided they are mounted on hydraulic floor springs and clearance at floor not exceeding 4.77 millimetres and frame and meeting stiles not exceeding 3 millimetres;
PROPOSED AMENDMENT
Remarks
(iii) a vision panel may be incorporated provided it does not exceed 0.065 square metre per leaf with no dimension more than 1 370 millimetres and it is glazed with 6 millimetres Georgian Wired Glass in hardwood stops; (iv) doors constructed in accordance with BS No. 459; Part 3: 1951 Fire Check Flush Doors and Wood and Metal Frames (Half-Hour
Page 73
NO.
EXISTING PROVISION
Type); (v) timber frames for single swing half-hour fire doors of overall width of 60 millimetres including 25 millimetres rabbet and depth to suit door thickness plus 34 millimetres stop;
PROPOSED AMENDMENT
Remarks
(vi) metal frames for half-hour fire doors shall be of sheet steel not lighter than 18 gauge of overall width 50 millimetres including 18 millimetres rabbet and depth to suit the door thickness plus 53 millimetres stop; (vii) timber or metal frames for double swing doors shall be as specified above with minimum clearances between frame and door; (b) doors and frames constructed in accordance with one of the following specifications shall be deemed to satisfy the requirements for doors having
Page 74
NO.
EXISTING PROVISION
FRP of one hour: (i) a single door not exceeding 900 millimetres wide X 2100 millimetres high or double doors not exceeding 1800 millimetres X 2100 millimetres high constructed as for specification (a) for half-hour door but incorporating on both faces either externally or beneath the plywood faces a layer of asbestos insulating board to BS 3536 (not asbestos cement) not less than 3 millimetres thick; doors may swing one way only and double doors shall have 12 millimetres wide rabbet at the meeting stiles;
PROPOSED AMENDMENT
Remarks
(ii)
(iii) a vision panel may be incorporated provided it does not exceed 10 square metres per leaf with no dimension more than 300 millimetres and it is glazed with 6 millimetres Georgian Wire
Page 75
NO.
EXISTING PROVISION
Glass in hardwood stop; (iv) doors constructed in accordance with BS No. 459: Part 3: 1951: Fire Check Flush Doors and Wood and Metal Frames (One Hour Type):
PROPOSED AMENDMENT
Remarks
83.
frames for one hour doors shall be as for half-hour doors except that timber frames shall be pressure impregnated with 15% to 18% solution of monoammonium phosphate in water. 165. Measurement of travel distance 165. Measurement of travel distance to to exits. exits. (3) In the case of individual rooms which are subject to occupancy of not more than six persons, the travel distance shall be measured from the doors of such rooms: (3) In any of individual room which is To clarify that this requirement is subjected to occupancy of not more than applicable to each individual room. six persons, the travel distance shall be measured from the door of such room:
(v)
Provided that the travel distance from Provided that the area of the room does not Measurement based on floor area of any point in the room to the room door exceed 15 square metres or any other area a room provides stricter control. does not exceed 15 metres. determined by the Fire Authority.
Page 76
NO.
84.
EXISTING PROVISION
167. Storey exits. (1) Except as provided for in by-law 194 every compartment shall be provided with at least two storey exits located as far as practical from each other and in no case closer not exceed than 4.5 metres and in such position that the travel distances specified in the Seventh Schedule to these By-laws are not exceeded.
PROPOSED AMENDMENT
167. Storey exits.
Remarks
(1) Except as provided for in by-law 194 To streamline with by-law 174. every compartment shall be provided with at least two storey exits located as far as practical from each other and shall not be less than 5.0 metres and in such position that the travel distances specified in the Seventh Schedule to these By-laws are not exceeded.
85.
168. Staircases. (3) The required width of a staircase shall be the clear width between walls but handrails may be permitted to encroach on this width to a maximum of 75 millimetres.
168. Staircases. (3) The required width of a staircase shall 80 milimetres is more appropriate be the clear width between walls but measurement. handrails may be permitted to encroach on this width to a maximum of 80 millimetres.
86.
No exit route may reduce in width along (1) No exit route may reduce in width along its path of travel from the storey exit to its path of travel from the storey exit to the the final exit. final exit. -None(2) For hospital and nursing home of This provision is transferred from Purpose Group II (Institutional) the existing Notes (ii) and (iii) under the Institutional item of the Tenth
Page 77
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
(a) corridors and landings shall be be Schedule because these designed to accommodate requirements are planning matters stretcher and bed movement; and (rather than fire protection systems) and therefore should be covered (b) design shall provide for horizontal under this Part. evacuation of bed patients for at least 50% of the total bed patients from the floor concerned.
87.
(3) Every exit sign shall have the word (3) The design and installation of every To adopt MS 983 and MS 619. "KELUAR" in plainly legible letters not emergency exit sign shall be in compliance less than 150 millimetres high with the with MS 983 and MS 619. principal strokes of the letters not less than 18 millimetres wide. The lettering shall be in red against a black background. 88. 189. Enclosing means of escape in 189. Enclosing means of escape in certain buildings. certain buildings. (1) Every staircase provided under these By-laws in a building of four storeys or more, or in a building where the highest floor level is more than 1,200 millimetres (1) Every staircase provided under these 12 metres is the correct By-laws in a building of four storeys or measurement, not 1,200 milimetres. more, or in a building where the highest floor level is more than 12 metres above
Page 78
NO.
EXISTING PROVISION
above the ground level, or in any place of assembly, or in any school when such staircase is to be used as an alternative means of escape shall be enclosed throughout its length with fire resisting materials. -None-
PROPOSED AMENDMENT
the ground level, or in any place of assembly, or in any school when such staircase is to be used as an alternative means of escape shall be enclosed throughout its length with fire resisting materials. (2) In a building of Purpose Group IV (Office), open corridor design may have unenclosed staircases if provided with extended landings of not less than twice staircase width and walls separating the staircase from the occupancy be returned for a distance of not less than 1 metre along the frontage of adjacent occupancies.
Remarks
This provision is transferred from the existing Note under the Office item of the Tenth Schedule because this requirement is a planning matter (rather than fire protection systems) and therefore should be covered under this Part. The original term open balcony approach is changed to open corridor design because the latter is more precise term. The purpose of this requirement is to prevent the spread of fire to the staircase.
89.
A single staircase may be permitted in A single staircase may be permitted in the To provide better control concerning any building the top most floor of which following premises: the usage of single staircase in does not exceed 12 metres in height: order to mitigate the risk of fire. (a) any dwellings at a height of 12 metres Provided that such building complies measured from the fire appliance with the following conditions: access level to the highest and lowest floor; and
Page 79
NO.
EXISTING PROVISION
(a) each element of structure shall have a FRP of not less than one hour; (b) no room or storey of the building may be used for any occupancy other than for domestic or office purpose, except that the ground storey may be used for the purposes of a shop or car park: Provided that (i) the staircase from the ground to first floor level shall be separated from the remainder of the ground floor by a wall having a FRP of not less than two hours; the wall enclosing the staircase at the main entrance be returned for a distance of not less than 450 millimetres along the frontage of any shop or car park; maximum travel
PROPOSED AMENDMENT
(b) any shophouses or dwellings not exceeding two (2) storeys or the first storey not exceeding 6 metres from the ground level.
Remarks
(ii)
(iii) the
Page 80
NO.
EXISTING PROVISION
distance shall be 12 metres measured from the door of the room or area to the exit provided the path of travel from any point in the room to the room door does not exceed 12 metres; (iv) in ground and first storeys which have windows containing opening lights sufficiently near the adjacent ground level as to make emergency escape by this means reasonable a maximum travel distance up to 30 metres is permissible.
PROPOSED AMENDMENT
Remarks
90.
197. Protected lobbies. (2) In buildings exceeding 45 metres above ground level, such protected lobbies shall be pressurised to meet the requirements of Section 7 of the Australian Standard 1668, Part 1 1974 or any other system meeting the functional requirements of the D.G.F.S.
197. Protected lobbies. (2) In buildings exceeding 45 metres above Consequential amendment to byground level, such protected lobbies shall law 133: Interpretation. be pressurised to meet the requirements of Section 7 of the Australian Standard 1668, Part 1 1974 or any other system meeting the functional requirements of the D.G.F.R.
Page 81
NO.
91.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
197A. Means of access and fire fighting in building over 18.0 metres high. (1) Buildings in which the topmost floor is more than 18.0 metres above fire appliance access level shall be provided with means of gaining access and fighting fire from within the building consisting of fire fighting access lobbies, fire fighting staircases, fire lifts and dry or wet rising systems.
Remarks
Paragraphs (1) to (6) are shifted from the existing by-law 229 because these requirements are planning matters and therefore should be covered under this Part. There are proposed amendments to the measurement so as to be in line with the current practice, i.e. 18.3 to (2) Fire fighting access lobbies shall be 18.0 metres in paragraph (1) and provided at every floor level and shall be so 45.75 to 45 metres in paragraph (2). located that the level distance from the furthermost point of the floor does not exceed 45.0 metres. (3) Fire fighting access lobbies may be ommitted if the fire fighting staircase is pressurised to meet the requirements of bylaw 200 and all fire fighting installations within the pressurised staircase enclosure do not intrude into the clear space required for means of egrees. (4) A fire fighting staircase shall be provided to give direct access to each fire fighting access lobby and shall be directly accessible from outside the building at fire appliance access level. This may be one of
Page 82
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
the staircases required as a means of egrees from the building. (5) A fire lift shall be provided to give access to each fire fighting access lobby or in the absence of a lobby to the fire fighting staircase at each floor level. (6) The fire lift shall discharge directly into the fire fighting access lobby fire fighting staircase or shall be connected to it by a protected corridor.
Remarks
(7) In a building where the top occupied Paragraphs (7) to (10) are shifted floor is over 18.5 metres above the fire from the existing by-law 243 as appliance access level fire lifts shall be these are planning matters. provided. (8) A penthouse occupying not more than 50% of the area of the floor immediately below shall be exempted from this measurement. (9) The fire lifts shall be located within a separate protected shaft if it opens into a separate lobby. (10) Fire lifts shall be provided at the rate of one lift in every group of lifts which
Page 83
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
discharge into the same protected enclosure or smoke lobby containing the rising main, provided that the fire lifts are located not more than 61 metres travel distance from the furthermost point of the floor. (11) All lifts serving upper floors shall not extend to basement floors except where the basement floors only contain low fire loads or are used solely for car parking. In all the permitted situations, protected lobbies shall be provided which shall be interposed between the lift openings and the areas served.
Remarks
This new provision is in line with the current practice. The expression in all permitted situation means if the lifts serving upper floors are allowed to be extended to basement floors. In this situation, enclosed lobbies (e.g. which are not open to the carparks) shall be provided.
92.
-None-
Transferred from the existing by-law 242 because it is a planning matter Fire fighting access lobbies shall conform and therefore should be covered to the following requirements: under this Part. In addition, there is a proposed amendment to (a) each lobby shall have a floor area of substitute 5.57 square metres with not less than 6.0 square metres; and 6.0 square metres so as to be in line with the current practice. (b) the openable area of windows or area of permanent ventilation shall be not less than 25% of the floor area of the lobby and, if ventilation is by means of openable windows, additional permanent ventilation
Page 84
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
having a free opening of 464 square centimetres shall be provided except that mechanical pressurisation may be provided as an alternative.
Remarks
93.
of
(2) Openable windows shall meet the (2) Openable windows shall meet the Consequential amendment to byoperational requirements of the D.G.F.S. operational requirements of the D.G.F.R. law 133: Interpretation. (3) In buildings not exceeding three storeys above ground level, staircase enclosures may be unventilated, provided that access to them at all levels except the top floor is through ventilated lobbies. -DeletedTo clarify the confusion concerning the application of by-laws 198(3) and 199.
Page 85
NO.
94.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
199. Ventilation of staircase 199. Ventilation of staircase enclosures enclosures in buildings not exceeding in buildings not exceeding three storeys 18 metres. or 18 metres. In buildings not exceeding 18 metres above ground level, staircase enclosures may be unventilated, provided that access to them at all levels except the top floor is through ventilated lobbies and the staircase enclosures are permanently ventilated at the top with least 5% of the area of the enclosures. In buildings not exceeding three storeys or Refer to proposed amendment to 18 metres, whichever is the earlier, above by-law 198(3). ground level, staircase enclosures may be unventilated, provided that access to them at all levels except the top floor is through ventilated lobbies and the staircase enclosures are permanently ventilated at the top with least 5% of the area of the enclosures. 200. Ventilation of staircase enclosures in buildings exceeding 18 metres. (b) mechanically pressurisation of the To adopt MS 1472. staircase enclosure designed and installed in accordance with MS 1472.
95.
96.
200. Ventilation of staircase enclosures in buildings exceeding 18 metres. (b) mechanically pressurisation of the staircase enclosure to the standard of performance as specified in section 7 of the Australian Standard 1668, Part 1 1974 or any other system meeting the functional requirements of the D.G.F.S. 202. Pressurized system for staircases.
system
for
All staircases serving buildings of more All staircases serving buildings of more To adopt MS 1472. than 45.75 metres in height where there than 45 metres in height where there is no
Page 86
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
is no adequate ventilation as required adequate ventilation as required shall be shall be provided with a basic system of provided with a staircase pressurization pressurization system designed and installed in accordance with MS 1472. (a) where the air capacity of the fan shaft be sufficient to maintain an air flow of not less than 60 metres per minute through the doors which are deemed to be open; (b) where the number of doors which are deemed to be opened at the one time shall be 10% of the total number of doors opening into the staircase with a minimum number of two doors open; where with all the doors closed the air pressure differential between the staircases and the areas served by it shall not exceed 5 millimetres water gauge; where the mechanical system to prevent smoke from entering the staircase shall be automatically activated by a suitable heat
Page 87
(c)
(d)
NO.
EXISTING PROVISION
detecting device, manual or automatic alarm or automatic wet pipe sprinkle system; and (e) which meets the funcational requirement as may be agreed with the D.G.F.S.
PROPOSED AMENDMENT
Remarks
97.
204. Classification of restriction of 204. Classification of restriction of flame flame over surface wall and ceiling. over surface wall and ceiling. For the purpose of this Part and the Eight Schedule to these By-laws any reference to a surface being of a specified class shall be construed as a requirement that the material of which the wall, ceiling or soffit is construed, shall comply with the following requirements: Class O. Surface of no flame spread. (A) Any reference to a surface being Class O shall be construed as a requirement that (a) the material of which the wall or ceiling is construed shall be non combustible throughout; or For the purpose of this Part and the Eight Schedule to these By-laws any reference to a surface being of a specified class shall be construed as a requirement that the material of which the wall, ceiling or soffit is construed, shall comply with the following requirements:
Class O. Surface of no flame spread. (a) Any reference to a surface being Class O shall be construed as a requirement that (i) the material of which the wall or ceiling is construed shall be non combustible throughout; or
Page 88
NO.
EXISTING PROVISION
(b) the surface material, or if it is bonded throughout to a substrate, the surface material in conjuction with the substrate, shall when tested in accordance with BS 476; Part 6, 1968, have an index of performance (A) not exceeding 12 and a subindex (i) not exceeding 6: Provided that the face of a plastic material having a softening point less than 120C Centigrade when tested by method 102 C of BS 2782: 1970, shall only be regarded as a surface of Class O if (i) the material is bonded throughout to a substrate which is not a plastic material and the material in conjunction with the substrate satisfies the test criteria prescribed in (a) above; or the material satisfies the test criteria prescribed in (b) above and is used as a
PROPOSED AMENDMENT
Remarks
(ii) the surface material, or if it is Reference to be made to the bonded throughout to a substrate, Standards as a whole. the surface material in conjunction with the substrate, shall when tested in accordance with BS 476.
-Deleted-
(ii)
Page 89
NO.
EXISTING PROVISION
lining of a wall so constructed that any surface which would be exposed if this lining were not present, satisfies the said test criteria and is the face of a material other than a plastic materil having a softening point less than 120C. (B) Any reference to a surface being of a class other than Class O shall be construed as a requirement that the material of which the wall or ceiling is constructed shall comply with the relevant test criteria as to surface spread of flame specified in relation to that class in clause 7 of BS 476: Part 1, Section 2, 1953.
PROPOSED AMENDMENT
Remarks
(b) Any reference to a surface being of a class other than Class O shall be construed as a requirement that the material of which the wall or ceiling is constructed shall comply with the relevant test criteria as to surface spread of flame specified in relation to that class in clause 7 of BS 476.
(C) In relation to a requirement that a (c) surface shall be of a class not lower than a specified class, Class O shall be regarded as the highest class followed in descending order by Class 1, Class 2, Class 3 and Class 4. . .
In relation to a requirement that a surface shall be of a class not lower than a specified class, Class O shall be regarded as the highest class followed in descending order by Class 1, Class 2, Class 3 and Class 4.
Page 90
NO.
98.
EXISTING PROVISION
207. Exception relating to ceilings.
PROPOSED AMENDMENT
207. Exception relating to ceilings.
Remarks
The original provision is no longer relevant in the current practice. It refers to certain construction specifications. New materials produced from new technology would be difficult to comply with these requirements. Therefore it is proposed to be deleted. The new provision proposed is to provide the exception to the requirements of bylaw 204 and the conditions thereof. It is formulated for the purpose of control over construction materials used in areas for means of escape.
(1) Any part of the ceiling of a room or Walls and ceiling finishes in the form of thin circulation space may consist of sheet of not more than 1 millimetre thickness mounted on a non combustible (a) rigid polyvinyl chloride sheeting substrate shall not be subject to the which is classified as self- requirement of surface spread of flame extinguishing when tested in provisions provided that this exception shall accordance with test method not apply to smoke stop or fire figthing 508 A or BS 2782: 1970 if the lobbies, and exit staircase and face of the sheeting which is passageway. not the surface of the ceiling is exposed to the external air; or (b) one or more panels of such plastic materials as are permitted by paragraph (2) if the upper and lower surfaces of any part of the ceiling which is not formed by a panel of plastic material and the surfaces of all other parts of the structure which enclose the space over the ceiling are of a class not lower than that prescribed in the Eight Schedule to these Bylaw for the ceiling of such a room or circulation space.
NO.
EXISTING PROVISION
refers may consist of one or more sheets or membranes of either (a) polyvinyl chloride which has a degree of flammability of not more than 75 millimetres when tested in accordance with method 508 C of BS 2782; 1970 or which has very low flammability when tested and classified in accordance with method 508 D of BS 2782: 1970, if (i) the nominal thickness of the sheet or membrane or, if a panel consist of two or more sheets or membranes, their nominal aggregate thickness does not exceed; and 0.99 millimetre; and
PROPOSED AMENDMENT
Remarks
(ii) no panel has an area exceeding 4.0876 square metres; or (b) any plastic material which has a
Page 92
NO.
EXISTING PROVISION
softening point of not more than 120C when tested by method 102 C of BS 2782: 1970, and a burning rate of not more than 50 millimetres per minute when tested in a thickness of 3 millimetres in accordance with method 508 A of BS 2872: 1970, if (i) the nominal thickness of the sheet or membrance or, if a panel consists of two or more sheets or membranes, their nominal aggregate thickness does not exceed 30 millimetres;
PROPOSED AMENDMENT
Remarks
(ii) the aggregate area of the plastic material, if situated in a building or compartment of Purpose Group II, III or VII, does not exceed 30% of the floor area of floor area of the room or 15% of the floor are of the circulation space, as the case may be, or, if situated in a building or compartment of any other
Page 93
NO.
EXISTING PROVISION
purpose group, does not exceed 50% of the floor area of the room or 15% of the floor area of the circulation space, as the case may be; (iii) no panel has any side exceeding 4.75 metres in length or an area exceeding 4.4 square metres if situated in a room or 2.0438 square metres if situated in acirculation space but if two or more panels are group so that each is less than 575 millimetres from another, the said maximum dimensions shall be applied to the smallest rectangle which would wholly enclose all such panels; and (iv) every panel is loosely mounted in such a way that it will fall out of its mountings when softtened by heat.
PROPOSED AMENDMENT
Remarks
Page 94
NO.
99.
EXISTING PROVISION
211. Roofing materials. (1) If any part of a roof cannot be designated under by-law 208 on account of the low softening temperature of its covering material, such part shall be not less than 12.2 metres ot twice the height of the building, whichever is the greater, form any point on a boundary unless such part is (a)
PROPOSED AMENDMENT
211. Roofing materials. (1) Surface or materials for roof covering and roof construction shall have a surface spread of flame rating not lower than class 1, except in the case of Purpose Groups I and III shown in Fifth Schedule of these Bylaws and in buildings that are protected throughout with automatic sprinkler system.
Remarks
This provision is deleted and substituted with a new provision to provide less prescriptive requirements on the control over the materials to be used for roof construction.
of an area not exceeding 3 (2) D.G.F.R. may approve the use of square metres; and combustible material for roof construction for buildings of Purpose Groups II, IV, V (b) separated from any other part and VI as shown in Fifth Schedule to these of the same roof which is By-laws if the following requirements are covered with the same material satisfied: or any other material by a distance which is at least 1.53 (a) the building does not exceed four metres wide and covered with storeys; non-combustible material, (b) the roof space between the roof in which case such part shall be not less and the ceiling shall be cavity than 6 metres from any such point. barrier where required to comply with relevant provisions, and (2) Nothing in this Part shall be prevent openings in cavity barriers shall any part of a roof being constructed of be fire-stopped; and such glass or rigid polyvinyl chloride sheeting as cannot be designated in (c) if the underside of the roof serves
Page 95
NO.
EXISTING PROVISION
accordance with by-law 208 but which, in the case of sheeting, is classified as selfextiguishing when tested in accordance with method 508A of BS 2782: 1970, whether either (a)
PROPOSED AMENDMENT
as ceiling to room or space, the elements of the underside or the roof shall comply with the relevant provision of by-law 204.
Remarks
(3) At the junctions with separating wall or that part of the roof is not less compartment wall, the roof construction than 6 metres from any shall comply with the requirements as the boundary; or Fire Authority may specify. that part of the roof is less than 6 metres from any boundary, and the roof is that of a garage, conservatory or outbuilding having a floor area not exceeding 40 square metres whether or not attached to a forming part of another building, or is the roof of, or canopy over, a balcony, verandah, open carpark, covered way or detached swimming pool.
(b)
Page 96
NO.
100.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
211A. Materials For Construction. (1) Materials used in the construction of building elements shall comply with the requirements stated under this Part in addition to the performance requirements such as for fire resistance and limit to spread of flame. (2) Instumescent paints is allowed to be used for protection of structural steel member of all building provided that (a) the paints shall be of proprietary system that has been tested to achieve the fire resistance performance as required in BS 476; and coating of instumescent paint onto structural steel, and subsequent maintenance shall conform to BS 8202.
Remarks
To emphasise that the materials for the construction of building shall conform to performance specifications.
(b)
(3) In buildings which are protected by automatic sprinkler system, fire rated glass can be used for the construction of compartment wall, compartment floors, enclosure to smoke stop lobby, fire fighting lobby, protected shafts not containing exit
Page 97
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
staircase and fire lift, subject to the following: (a) the wall and doors shall have necessary fire resistance, including insulation, when subject to test under BS 476 for the wall and MS 1073 for the door; and the walls and door shall meet the Class A of impact performance requirements when subject to test under BS 6206 or AS 2208.
Remarks
(b)
(4) Walls, ceiling, roof covering and finishes shall not contain any plastic material. (5) For the purpose of this by-law, AS means the latest published edition of the Australian Standard. 101. 222. Fire resistance for walls. (4) : Provided that, for the purposes of these by-laws, the wall shall be capable of satisfying the requirements of clause 11c of section 3 of BS 476: Part 1: relating to insulation, for a period of not less than fifteen minutes. 222. Fire resistance for walls. (4) : Provided that, for the purposes of these by- For reference to be made to the laws, the wall shall be capable of satisfying Standard as a whole. the requirements of clause 11c of section 3 of BS 476 relating to insulation, for a period of not less than fifteen minutes.
Page 98
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
102. 223. Fire resistance for floors above 223. Fire resistance for floors above ground floor. ground floor. Any floor above the ground storey of a house falling within Purpose Group 1 shall, if the underside of such floor is exposed to test by fire in accordance with BS 476: Part 1: be capable of satisfying the requirements of that test as to freedom from collapse for a period of not less than half an hour and as to insulation and resistance to passage of flame for not less than fifteen minutes. Any floor above the ground storey of a For reference to be made to the house falling within Purpose Group I shall, Standards as a whole. if the underside of such floor is exposed to test by fire in accordance with BS 476 be capable of satisfying the requirements of that test as to freedom from collapse for a period of not less than half an hour and as to insulation and resistance to passage of flame for not less than fifteen minutes.
Page 99
NO.
103.
EXISTING PROVISION
PART VIII FIRE ALARMS, FIRE DETECTlON, FIRE EXTINGUISHMENT AND FIRE FIGHTING ACCESS
PROPOSED AMENDMENT
PART VIII FIRE DETECTlON, FIRE ALARM AND FIRE EXTINGUISHMENT
Remarks
FIRE ALARM is inserted after FIRE DETECTION because the fire fighting systems will detect and warn later. FIRE FIGHTING ACCESS is deleted because it is a planning matter and should be covered under Part VII.
warning
and
(1) Every building shall be provided with means of detecting and extinguishing fire and with fire alarms together with illuminated exit signs in accordance with the requirements as specified in the Tenth Schedule to these By-laws. (2) Every building shall be served by at least one fire hydrant located not more than 91.5 metres from the nearest point of fire brigade access
(1) Every building shall be provided with means of detecting, warning and extinguishing fire in accordance with the requirements as specified in the Tenth Schedule to these By-laws.
The fire fighing systems should be able to detect, warn and extinguish fire. The requirement of illuminated exit signs has already been covered under by-law 172.
(2) Every building shall be served by at To streamline with MS 1489. The least one fire hydrant located not more than term nearest point of is deleted to 45 metres from the fire brigade access, avoid confusion. designed and installed in accordance with MS 1489. In any case, hydrants shall be located not more than 90 metres apart. (3) Depending on the size and location of To streamline the building and the provision of access for practice. fire appliances, additional fire hydrants shall be provided as may be required by the D.G.F.R. with the current
(3) Depending on the size and location of the building and the provision of access for fire appliances, additional fire hydrants shall be provided as may be required by the Fire Authority.
Page 100
NO.
105.
EXISTING PROVISION
-None-
PROPOSED AMENDMENT
226A. Hose reel systems.
Remarks
Hose reel systems shall be designed and To streamline with the relevant installed in accordance with MS 1489. Malaysian Standard. 106. 227. Portable extinguishers. 227. Portable extinguishers.
Portable extinguisher shall be provided Portable extinguisher shall be designed To streamline with the relevant in accordance with the relevant codes of and installed in accordance with MS 1539. Malaysian Standard. practice and shall be sited in prominent positions on exit routes to be visible from all directions and similar extinguishers in a building shall be of the same method of operation. 107. 228. Sprinkler valves. (1) Sprinkler valves shall be located in a safe and enclosed position on the exterior wall and shall be readily accessible to the Fire Authority. (2) All sprinkler systems shall be electricity connected to the nearest fire station to provide immediate and automatic relay of the alarm when activated. 228. Sprinklers systems. Sprinkler systems shall be designed and To streamline with the relevant installed in accordance with MS 1910. Malaysian Standard.
Page 101
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
108. 229. Means of access and fire fighting 229. Means of access and fire fighting To be in line with the current inbuilding over 18.3 metres high. inbuilding over 18 metres high. practice. (1) Buildings in which the topmost floor is more than 18.3 metres above fire appliance access level shall be provided with means of gaining access and fighting fire from within the building consisting of fire fighting access lobbies, fire fighting staircases, fire lifts and dry or wet rising systems. (2) Fire fighting access lobbies shall be provided at every floor level and shall be so located that the level distance from the furthermost point of the floor does not exceed 45.75 metres. 109. 230. Installation and testing of dry rising system. (1) Dry riser systems shall be provided in every building in which the topmost floor is more than 18.3 metres but less than 30.5 metres above fire appliance access level. (1) Buildings in which the topmost floor is more than 18 metres above fire appliance access level shall be provided with means of gaining access and fighting fire from within the building consisting of fire fighting access lobbies, fire fighting staircases, fire lifts and dry or wet rising systems.
(2) Fire fighting access lobbies shall be provided at every floor level and shall be so located that the level distance from the furthermost point of the floor does not exceed 45 metres. 230. Dry riser systems.
(1) Dry riser systems shall be provided in every building in which the topmost occupied floor is more than 18 metres but less than 30 metres above fire appliance access level.
To clarify that topmost floor is the occupied floor because in certain building, the topmost floor is M&E room.
(2) A hose connection shall be provided (2) Dry riser systems shall be designed and in each fire fighting access lobby. installed in accordance with MS 1489 such that all parts of the floor are within 45 metres from a landing valve.
To streamline with the relevant Malaysian Standard. Also to be consistent with the new by-law 197A(2).
Page 102
NO.
EXISTING PROVISION
(3) Dry risers shall be of minimum "Class C" pipes with fittings and connections of sufficient strength to withstand 21 bars water pressure. (4) Dry risers shall be tested hydrostatically to withstand not less than 14 bars of pressure for two hours in the presence of the Fire Authority before acceptance. (5) All horizontal runs of the dry rising systems shall be pitched at the rate of 6.35 millimetres in 3.05 metres.
PROPOSED AMENDMENT
-Deleted-
Remarks
These are covered by MS 1489.
-Deleted-
-Deleted-
(6) The dry riser shall be not less than 102 millimetres in diametre in buildings in which the highest outlet is 22.875 metres or less above the fire brigade pumping inlet and not less than 152.4 millimetres diametre where the highest outlet is higher than 22.875 metres above the pumping inlet. (7) 102 millimetres diametre dry risers shall be equipped with a two-way pumping inlet and 152.4 millimetres dry risers shall be equipped with a four-way
-Deleted-
-Deleted-
Page 103
NO.
EXISTING PROVISION
pumping inlet.
PROPOSED AMENDMENT
Remarks
110. 231. Installation and testing of wet 231. Wet riser systems. rising system. (1) Wet rising systems shall be provided in every building in which the topmost floor is more than 30.5 metres above fire appliance access level. (1) Wet rising systems shall be provided in To streamline with the relevant every building in which the topmost Malaysian standard. occupied floor is more than 30 metres above fire appliance access level.
(2) A hose connection shall be provided (2) Wet riser systems shall be designed in each fire fighting access lobby. and installed in accordance with M.S. 1489 such that all parts of the floor are within 45 metres from a landing valve.
(3) Wet risers shall be of minimum 152.4 millimetres diametre and shall be hydrostatically tested at a pressure 50% above the working pressure required and not less than 14 bars for at least twentyfour hours. (4) Each wet riser outlet shall comprise standard 63.5 millimetres instantaneous coupling fitted with a hose of not less than 38.1 millimetres diametre equipped with an approved typed cradle and a variable fog nozzle.
-Deleted-
-Deleted-
Page 104
NO.
EXISTING PROVISION
(5) A wet riser shall be provided in every staircase which extends from the ground floor level to the roof and shall be equipped with a three-way 63.5 millimetres outlet above the roof line. (6) Each stage of the wet riser shall not exceed 61 metres, unless expressly permitted by D.G.F.S but in no case exceeding 70.15 metres.
PROPOSED AMENDMENT
-Deleted-
Remarks
-Deleted-
111. 233. Foam inlets. Boiler rooms and storage areas below ground level where automatic extinguishing installations are not provided shall be equipped with foam inlets.
-Deleted-
Boiler rooms and storage areas refer to special hazardous areas and this requirement has already been covered under Note 2 of Group VI under the Tenth Schedule to these By-laws. Furthermore, the suitability of the use of foam inlets should be determined by the Fire Authority.
112. 234. Underground structures and windowless buildings to have foam inlets. All underground structures, windowless buildings depending on the type of occupancy, storage, processes or type of protection installed shall be provided -DeletedThese buildings refer to special hazardous areas and should be covered under the Tenth Schedule.
Page 105
NO.
EXISTING PROVISION
with foam inlets as may by the Fire Authority. be required
PROPOSED AMENDMENT
Remarks
113. 235. Fixed installation. Fixed installations shall either be total flooding system or unit protection system depending upon the nature of hazard process and occupancy as may be required by the Fire Authority. 114. 236. Special hazards. Places constituting special hazards or risk due to the nature of storage, trade, occupancy or size shall be required to be protected by fixed installations, protective devices, systems and special extinguishers as may be required by the Fire Authority. 115. 237. Fire Alarms.
235. Fixed extinguishing systems. Fixed extinguishing systems shall either be To clarify that the system is meant total flooding system or unit protection for fire extinguishment. system depending upon the nature of hazard process and occupancy as may be required and approved by the D.G.F.R. 236. Special hazards. Places constituting special hazards or risk In line with the current practice. due to the nature of storage, trade, occupancy or size shall be required to be protected by fixed installations, protective devices, systems and special extinguishers as may be required by the D.G.F.R.
(1) Fire alarms shall be provided in Fire detection and fire alarm systems shall To streamline with the relevant accordance with the Tenth Schedule to be designed and installed in accordance Malaysian Standard. these By-laws. with MS 1745. (2) All premises and buildings with gross floor area excluding car park and storage -Deleted-
Page 106
NO.
EXISTING PROVISION
areas exceeding 9290 square metres or exceeding 30.5 metres in height shall be provided with a two-stage alarm system with evacuation (continuous signal) to be given immediately in the affected section of the premises while an alert (intermittent signal) be given in adjoining section. (3) Provision shall be made for the general evacuation of the premises by action of a master control.
PROPOSED AMENDMENT
Remarks
-Deleted-
116. 238. Command and control centre. Every large premises or building exceeding 30.5 metres in height shall be provided with a command and control centre located on the designated floor and shall contain a panel to monitor the public address, fire brigade communication, sprinkler, waterflow detectors, fire detection and alarm systems and with a direct telephone connection to the appropriate fire station by-passing the switchboard.
238. Fire Command Centre. Where it is specified in the Tenth Schedule More relevant to these By-Laws that a fire command practice. centre shall be provided, the fire commond centre shall be located on the designated floor with easy fire appliances access and shall contain a panel to monitor the public address, fireman intercom, sprinkler, waterflow detectors, fire detection and alarm systems and with a computerised monitoring system connected to the appropriate fire station by-passing the with the current
Page 107
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
switchboard.
Remarks
117. 239. Voice communication system. 239. Voice communication system. (b) in every office area exceeding (b) in every office area exceeding 100 To provide more convenient 92.9 square metres in area; square metres in area; measurement and technically there . . is not much different between 92.9 and 100 metres. 118. 240. Electrical isolating switch. (1) Every floor or zone of any floor with a net area exceeding 929 square metres shall be provided with an electrical isolation switch located within a staircase enclosure to permit the disconnection of electrical power supply to the relevant floor or zone served. (2) The switch shall be of a type similar to the fireman's switch specified in the Institution of Electrical Engineers Regulations then in force. 240. Electrical isolating switch. (1) Every floor or zone of any floor with a To provide more convenient net area exceeding 1000 square metres measurement. Also to adopt the shall be provided with an electrical isolation relevant Standard. switch complying with IEC 60947-3 and located within a staircase enclosure to permit the disconnection of electrical power supply to the relevant floor or zone served. (2) For purpose for this by-law, IEC means the latest published edition of the International Electrotechnical Commission Standard.
119. 241. Special requirements for fire 241. Special requirements for fire alarm alarm systems. systems. In places where there are deaf persons In places where there are deaf persons and To streamline with the relevant and in places where by nature of the in places where by nature of the occupancy Malaysian Standard. occupancy audible alarm system is audible alarm system is undesirable,
Page 108
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
undesirable, visible indicator alarm special requirement for fire alarm systems signals shall be incorporated in addition shall be installed in accordance with MS to the normal alarm system. 1745. 120. 242. Fire fighting access lobbies. Fire fighting access lobbies shall conform to the following requirements: (a) each lobby shall have a floor area of not less than 5.57 square metres; and the openable area of windows or area of permanent ventilation shall be not less than 25% of the floor area of the lobby and, if ventilation is by means of openable windows, additional permanent ventilation having a free opening of 464 square centimetres shall be provided except that mechanical pressurisation may be provided as an alternative. -DeletedShifted to new by-law 197B.
(b)
121. 243. Fire lifts. (1) In a building where the top occupied floor is over 18.5 metres above the fire -DeletedShifted to new by-law 197A(7) (10).
Page 109
NO.
EXISTING PROVISION
appliance access level fire lifts shall be provided. (2) A penthouse occupying not more than 50% of the area of the floor immediately below shall be exempted from this measurement. (3) The fire lifts shall be located within a separate protected shaft if it opens into a separate lobby. (4) Fire lifts shall be provided at the rate of one lift in every group of lifts which discharge into the same protected enclosure or smoke lobby containing the rising main, provided that the fire lifts are located not more than 61 metres travel distance from the furthermost point of the floor.
PROPOSED AMENDMENT
Remarks
122.
-None-
243A. Emergency mode of operation in Shifted from the existing by-law 154. the event mains power failure. (1) On failure of mains power of lifts shall return in sequence directly to the designated floor, commencing with the fire lifts, without answering any car or landing calls and park with doors open.
Page 110
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
(2) After all lifts are parked the lifts on emergency power shall resume normal operation: Provided that where sufficient emergency power is available for operation of all lifts, this mode of operation need not apply.
Remarks
123. 244. Standards required. All fire fighting installations and appliances shall conform to the current edition of the following standards: (a) Fire Hydrants BS 750:1977 and BS CP 402.101:1952 Hydraulic Hose Reels BS 5306 Part 1:1976 Portable Extinguishers BS CP 402 Part 3:1964 Dry/Wet Rising Mains BS 3980:1966 BS 5306 Part 1:1976 BS 750:1964 Foam Inlets -DeletedHas been 225(2). described in by-law
(b)
-Deleted-
(c)
-Deleted-
(d)
-Deleted-
(e)
-Deleted-
NO.
(f)
EXISTING PROVISION
BS 3980:1966 Automatic Sprinklers FOC Rules 29th Edition: 1973 Fire Alarm Systems FOC Rules:1973 BS CP 1019:1972 BS 3116 Part 1:1970 BS 3116 Part 4:1974 BS 5446 Part 1:1977 Fire Dampers AS 1682:1974 Fire Lifts ... BS 2655: Part 1: Appendix E
PROPOSED AMENDMENT
practice. -Deleted-
Remarks
Has been described in by-law 228.
(g)
-Deleted-
(h)
-Deleted-
described
in
by-law
(i)
-Deleted-
described
in
by-law
Smoke Control AS 1668: Part 1:1974 124. 245. Approval of D.G.F.S. (j) (1) All fire fighting installations and appliances other than those conforming to the standards listed in by-law 244 shall be of those as tested and approved by the D.G.F.S.
(1) Any construction, development or To be in line with the current installation of fire fighting equipment or fire practice. safety installation other than those conforming to the requirements provided in Parts VII and VIII of these By-laws shall be submitted to and approved by the D.G.F.R.
Page 112
NO.
EXISTING PROVISION
(2) Plans, drawings and calculations of all fixed installations shall be submitted to the Fire Authority in a manner prescribed by the D.G.F.S. before commencement of work. (3) Every plan, drawing or calculation in respect of any automatic sprinklers or other fixed installations shall be submitted together with the relevant forms as prescribed in the Tenth Schedule to these By-laws.
PROPOSED AMENDMENT
before the commencement of work.
Remarks
(2) Plans, drawings and calculations of all To be in line with the current fire fighting installations shall be submitted practice. to the Fire Authority in a manner prescribed by the D.G.F.R. before commencement of work. -DeletedTo streamline with the current practice. The Forms in the Tenth Schedule should be applicable only upon completion. And the existing Form G9 under the Second Schedule to these By-laws has already covered the certification of completion concerning fire proctection systems.
125. 246. Certification on completion. When the fixed installation has been completed and final tests carried out the person submitting the plans shall certify to the Fire Authority on Form B as set out in the Tenth Schedule to these Bylaws that the work has been completed and the necessary tests carried out in accordance with the current D.G.F.S. rules for various fixed installations. 126. 247. Water storage. -DeletedForm B has been replaced by Form G9.
-Deleted-
NO.
EXISTING PROVISION
(1) Water storage capacity and water flow rate for firefighting systems and installations shall be provided in accordance with the scale as set out in the Tenth Schedule to these By-laws. (2) Main water storage tanks within the building, other than for hose reel systems, shall be located at ground, first or second basement levels, with fire brigade pumping inlet connections accessible to fire appliances.
PROPOSED AMENDMENT
Remarks
systems has been specified in MS 1489 (referred to in by-law 231) and MS 1910 (referred to in by-law 228).
(3) Storage tanks for automatic sprinkler installations where full capacity is provided without need for replenishment shall be exempted from the restrictions in their location. 127. 248. Marking on wet riser, etc. 248. Marking on wet riser, etc.
(1) Wet riser; dry riser, sprinkler and (1) Wet riser; dry riser, sprinkler and other To clarify that the whole pipes need other fire installation pipes and fittings fire installation pipes and fittings shall be not be painted red so long as it can shall be painted red. identified in red colour. be identified in red colour. (2) All cabinets and areas recessed in (2) All cabinets and areas recessed in walls D.G.F.R includes the Fire Authority. walls for location of fire installations and for location of fire installations and extinguishers shall be clearly identified to extinguishers shall be clearly identified to
Page 114
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
D.G.F.R. or
Remarks
the satisfaction of the Fire Authority or the satisfaction of the otherwise clearly identified. otherwise clearly identified.
128. 251. Smoke vents to be adequate to 251. Smoke vents to prevent dangerous prevent dangerous accumulation of accumulation of smoke. smoke. Where smoke venting facilities are Smoke control systems where specified To adopt MS 1780. installed for purposes of exit safety in shall be designed and installed in accordance with the requirements of this accordance with MS 1780. Part they shall be adequate to prevent dangerous accumulation of smoke during the period of time necessary to evacuate the area served using available exit facilities with a margin of safety to allow for unforeseen contingencies. 129. Smoke vents to be openable by Fire Authority. The discharge apertures of all manual smoke vents shall be so arranged as to be readily openable by the Fire Authority working from the exterior. 130. -None252A. Atriums in buildings. An atrium may be permitted in a building provided that To streamline practice. with the current -DeletedHas been covered by MS 1780.
Page 115
NO.
EXISTING PROVISION
(a)
PROPOSED AMENDMENT
the horizontal dimension is not less than 6 metres and the area of opening is not less than 95 square metres; the exits are separately enclosed from the atrium though exit access may be within the atrium; the atrium unobstructed; is open and
Remarks
(b)
(c)
(d)
the building is fully protected by automatic sprinklers; sprinklers may be omitted for ceiling of the atrium if it is more than 17 metres above the floor; a smoke control or smoke exhaust system of the atrium and adjacent spaces be provided as per Table 1 below or other approved standards; the smoke control or smoke exhaust system shall be activated by (i) smoke detectors located at the top of the atrium and adjacent to each return air intake from
Page 116
(e)
(f)
(g)
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
the atrium; (ii) the automatic sprinkler system; (iii) the automatic detector system (but not the manual break glass system); and (iv) manual controls readily accessible to the Fire Authority; and (h) the atrium be separated from adjacent spaces by one hour fire resistance fire barriers except that (i) any three levels of the building may open directly to the atrium without enclosure; and
Remarks
(ii) glass walls may be used in lieu of fire barriers where automatic sprinklers are spaced 1.8 metres or less apart along both sides of the glass wall, not more than 0.3 metres from the glass so that the surface of the glass is wet upon operation of the sprinklers. The glass shall be float glass held in place by a
Page 117
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
gasket system allowing the frame to deflect without the glass before the sprinklers operate.
Remarks
17 less
or
17,000 or less
19
17
or
17,000
19
Page 118
NO.
EXISTING PROVISION
less
PROPOSED AMENDMENT
or less 4 of Exhaust Mechanical 75% of Exhaust 17 or more
Remarks
131. 253. Emergency power system. (5) Current supply shall be such that in the event of failure of the normal supply to or within the building or group of buildings concerned, the emergency lighting or emergency power, or both emergency lighting and power will be available within 10 seconds of the interruption of the normal supply. The supply system for emergency purposes shall comprise one or more of the following approved types: . 132. -None-
253. Emergency power system. (5) Current supply shall be such that in the The current system is not able to event of failure of the normal supply to or achieve the existing requirement of within the building or group of buildings available within 10 seconds. concerned, the emergency lighting or emergency power, or both emergency lighting and power will be changed over within 60 seconds immediately after the interruption of the normal supply. The supply system for emergency purposes shall comprise one or more of the following approved types: . 253A. Emergency lights. Emergency lighting shall be installed to provide sufficient illumination for escape purposes. Such lighting shall be of the selfcontained type to MS 619 or supplied with emergency power from an emergency power system or central battery bank. In all cases, the duration of emergency illumination in the event of failure of normal supply shall not be less than one hour. This requirement is transferred from Note 4 of the Tenth Schedule to these By-laws with amendment to be in line with the current practice.
Page 119
NO.
EXISTING PROVISION
Remarks
133. 256. Buildings exempted. Except for by-law 141 and paragraph (2) of by-law 225 the provisions under Part VII and VIII of these By-laws shall not apply to private dwelling houses, detached or semi-detached and terrace houses intended for single family occupancies.
256. Buildings exempted. Except for by-laws 134 and 141 and paragraph (2) of by-law 225 the provisions under Part VII and VIII of these By-laws shall not apply to private dwelling houses, detached or semi-detached and terrace houses intended for single family occupancies. By-law 134 which provides the designation of purpose groups of buildings should not be exempted by this provision.
134. 257. Malaysian standard Specification 257. Application of standard or code of and Code of Practice to prevail over practice. British Standard Specification and Code of Practice. In these By-laws where there is any reference to the British Standard Specifications or British Code of Practice and there is, whether on the date of the coming into operation of these By-laws or subsequently, a corresponding Malaysian Standard Specification or Malaysian Code of Practice in respect of that subject, the Malaysian Standard Specification or Malaysian Code of Practice shall be deemed to have Where any standard or code of practice is To ensure the inclusiveness of the referred to in these By-laws, and there is latest published edition of the subsequently published a corresponding relevant standards. Malaysian Standard or any other corresponding standard or code of practice which is acceptable to the local authority or D.G.F.R., as the case may be, on the same subject matter, the corresponding Malaysian Standard or standard or code of practice shall be deemed to have superseded such standard or code of
Page 120
NO.
EXISTING PROVISION
PROPOSED AMENDMENT
Remarks
superseded the British Standard practice referred to and shall be complied Specification or British Code of Practice with. respectively and shall be deemed to apply. 135. 258. Failure to buildings. (1) In the event of any failure to any building or part of the building, whether in the course of construction or after completion, the principal submitting person or submitting person who 258. Failure to buildings. (1) In the event of any failure to any To include failure to building in the building or part of the building, whether in course of demolition. the course of erection or after completion, the principal submitting person or submitting person who
(a)
submitted the plans, drawings or calculations for such building; supervised the setting out of such building; certified that the setting out was carried out in accordance with the approved site plan; supervised the construction of such building; certified that the proper supervision of such building as
(a)
(b)
(b)
supervised the setting out of such building; certified that the setting out was carried out in accordance with the approved site plan; supervised the erection of such building; certified that the proper supervision of such building as
Page 121
(c)
(c)
(d)
(d)
(e)
(e)
NO.
EXISTING PROVISION
carried out; shall within one week of the occurrence of such failure or such further period as may be specified by the local authority within whose jurisdiction such building is situated (aa) report such failure; (bb) explain the cause of failure; and (cc) if such failure occurred during the construction of such building, state the remedial action taken. (2) Such principal submitting person or submitting person shall submit such further information in such manner and within such period as may be specified by the local authority. (3) Where the local authority has reason to believe that a failure to any building or part of a building has occurred which failure has not been reported to such local authority it shall serve a notice on the principal submitting person or
PROPOSED AMENDMENT
carried out; shall within one week of the occurrence of such failure or such further period as may be specified by the local authority within whose jurisdiction such building is situated
Remarks
(i) (ii)
(iii)
if such failure occurred during the erection of such building, state the remedial action taken.
(2) Such principal submitting person or submitting person shall submit such further information in such manner and within such period as may be specified by the local authority. (3) Where the local authority has reason to believe that a failure to any building or part of a building has occurred which failure has not been reported to such local authority it shall serve a notice on the principal submitting person or submitting person
Page 122
NO.
(a)
EXISTING PROVISION
submitting person who submitted the plans, drawings or calculations for such building; supervised the setting out of such building; certified that the setting out was carried out in accordance with the approved site plan; (a)
PROPOSED AMENDMENT
who submitted the plans, drawings or calculations for such building;
Remarks
(b)
(b)
supervised the setting out of such building; certified that the setting out was carried out in accordance with the approved site plan;
(c)
(c)
(d)
supervised the construction of such building; certified that proper supervision of such building was carried out;
(d)
supervised the erection of such building; certified that proper supervision of such building was carried out;
(e)
(e)
requiring him within one week of such requiring him within one week of such service to service to (aa) state whether occurred; such failure (i) state whether occurred; such failure
(ii)
Page 123
NO.
EXISTING PROVISION
(cc) if such failure occurred during the construction of such building, state the remedial action taken.
PROPOSED AMENDMENT
(iii) if such failure occurred during the erection of such building, state the remedial action taken.
Remarks
(4) Any principal submitting person or submitting person who fails to comply with paragraph (1), (2) or (3) shall be guilty of an offence. (5) Notwithstanding that any plan, drawing or calculation has been approved by the local authority, the responsibility for the failure of any building or part of a building shall prima facie lie with the principal submitting person or submitting person who submitted such plan, drawing or calculation. (6) The principal submitting person or submitting person as mentioned under paragraph (1)(a) of by-law 7 shall be subject to the same provision as specified under this by-law.
(4) Any principal submitting person or submitting person who fails to comply with paragraph (1), (2) or (3) shall be guilty of an offence. (5) Notwithstanding that any plan, drawing or calculation has been approved by the local authority, the responsibility for the failure of any building or part of a building shall prima facie lie with the principal submitting person or submitting person who submitted such plan, drawing or calculation.
(6) The principal submitting person or submitting person, as the case may be, as mentioned under paragraph (1)(a) of by-law 2F or paragraph (1)(a) of by-law 7 shall be subject to the same provision as specified under this by-law.
Page 124