Professional Documents
Culture Documents
Quantum Energy Generator - Free Energy Device Blueprints
Quantum Energy Generator - Free Energy Device Blueprints
3-25-2014
The Quantum Electric Generator system (QEG) is an adaptation of one of Nikola Teslas many patented electrical generator / dynamo / alternator designs. The particular patent referenced is No. 511,916, titled simply Electric Generator, and dated January 2, 1894 (see back of this manual) . The adaptation is a conversion from a linear system, to a rotary system. The QEG prototype is scaled to produce electrical power in the range of 10-15 kW (kilowatts) continuously, and can be set up to provide either 120 Volt or 230-240 Volt single phase output. We are also planning future designs to provide 3-phase power. Service life of the device is limited only by certain replaceable components, such as bearings, v-belts, and capacitors. The basic machine should operate trouble-free (with minimal maintenance) for as long as any good quality electro-mechanical appliance, such as a quality washing machine or refrigerator. Heavy-duty mechanical components are used throughout for reliability. The QEG is not a complicated device, as it is designed (like Teslas other discoveries), to work in harmony with natural laws, rather than with the power-wasting symmetric motor and generator designs used in todays mainstream industry. An effective way to understand the operating principle of the QEG is to think of it as a high-powered, selfresonant oscillator (a power tank circuit), which generates high-voltage AC (15 to 25kV). These HV oscillations are then transformed into line voltage AC output, at current levels up to approximately 85 A. In todays alternative energy terminology, it would be called a type of resonance machine. The circuitry that develops high power in this device is really based on an existing but under-utilized power oscillator configuration, however, the quantum part of the design has to do w ith how the generator output is tuned for maximum power. Conventional alternators (AC generators) consume more input power than the output power they provide. For example, one brand of power take off (PTO) alternator uses 18,000 watts (24 horsepower) to develop 13,000 watts of output power. In the QEG, input power is used only to maintain resonance in the core, which uses a small fraction of the output power (under 1000 watts to produce 10,000 watts), and once running, the QEG provides this power to its own 1 horsepower motor. This is known as overunity. Once the machine builds up to the resonant frequency, it powers itself (self-running). In the QEG, the exciter coil is used to provide a conduction path through the quantum field (zero point) into the generator core. This has the effect of polarizing the core, which increases power output over time.
James M. Robitaille
NOTICE
TO BE READ AND UNDERSTOOD BY ALL QEG PROJECT CREWS Fix the World (FTW) is not responsible for the actions of others. We can only tell you our experience. We have discovered it is essential that those wishing to build a QEG use careful thinking, patience, and consideration for the greater good. The inhabitants of planet Earth are entering into a new paradigm and a new way of doing business. In honor of Nikola Tesla, the QEG is a gift freely given to the world, and FTWs involvement is strictly altruistic. The QEG is an electromechanical device and as such, safety for the individual and end user should always be of prime concern. It is therefore essential that persons assembling the device are experienced in the field of electro-mechanical assembly. A considerable level of knowledge in quantum physics is also required. IF YOU ARE TRAINED IN TRADITIONAL PHYSICS, AND HAVE NOT BEEN DOING THIS WORK FOR MANY YEARS, YOU MUST FIRST DO YOUR RESEARCH ON BASIC QUANTUM ENERGY DEVICES AND HOW THEY WORK (e.g. resonance and tuning). Electrical / Mechanical devices are inherently dangerous. Electrical shock hazards can cause serious injury and in some cases death. Mechanical hazards can result in dismemberment and in some cases death. Due diligence has been applied to ensure that the QEG instructions are complete and correct. All local and country-specific electrical and mechanical code implications, by which a QEG might be installed and operated, cannot possibly be known. Nor is it conceivable that any and all possible hazards and/or results of each procedure or method have been accounted for. It is for these reasons that the QEG must be either directly installed or supervised by an experienced electromechanical engineer to ensure the installation is done safely and in accordance with local electrical code, however, the QEG is installed the same way as any commercial generator and does not violate any electrical codes. Anyone who uses the QEG installation instructions (including but not limited to any procedure or method of installation) must first satisfy themselves that neither their safety, nor the safety of the end user, will be endangered over the course of the installation and operation of the QEG. It is imperative to understand YOU NEED PROFESSIONALS AND EXPERT ADVICE to build a QEG.
The installation instructions are designed to show how we have found the building of the device to be accomplished, and any negative outcomes that result are completely the responsibility of the person/company building it; FTW provides no guarantee for the successful installation of the QEG. This notice serves the purpose of communicating the serious nature of building a quantum machine, as we are well aware that there have been severe restrictive agencies involved with their suppression. Quantum free energy isnt taught at University and most designers have heretofore been unsuccessful at mass distribution. It is YOUR RESPONSIBILITY therefore to make certain you are building the QEG with positive intentions for humanity, and lashing out legally or otherwise to FTW, HopeGirl and/or the designer and his family, is a violation of goodwill and will in no way be attended to. We know of no other way to do this but to go back to the HONOR SYSTEM. In reading this notice I agree that: 1) I WILL NOT ATTEMPT TO BUILD A QEG UNLESS I DO SO APPROPRIATELY WITH AN ELECTROMECHANCIAL ENGINEERING PROFESSIONAL. 2) I WILL NOT COMMISSION (TURN ON) OR INSTALL THE QEG WITHOUT AN ELECTROMECHANICAL ENGINEERING PROFESSIONAL. 3) UNDER THE ABOVE CONDITIONS, I MAY USE THE QEG INSTALLATION INSTRUCTIONS FOR PERSONAL USE, AND UNDERSTAND THE NEED FOR IMPECCABLE COMMITMENT TO THE BETTERMENT OF HUMANITY. IN THE BEST INTEREST OF THE PEOPLE OF PLANET EARTH, I WILL NOT ATTEMPT TO MISUSE OR MONOPOLIZE THE QEG INSTALLATION INSTRUCTIONS IN ANY CAPACITY, NOR WILL I ATTEMPT TO MAKE A HUGE PROFIT AT THE EXPENSE OF ANOTHER HUMAN BEING. IMPORTANT Please make certain that persons who are to use this equipment thoroughly read and understand these instructions and any additional instructions prior to construction, installation and operation. In addition, we require you to read this notice again when you are ready to assemble the core.
3-25-2014
Dear Builder, It is no easy task to build the QEG, and we want to encourage you by offering a short treatise on the importance of consciousness in this endeavor. Many are becoming more familiar with Nikola Tesla, his desire for all people to have access to free energy, and his failed attempt to expose this technology to the world. Many have followed him with the same aspirations and, similar to Teslas plight, have also been prevented by powers beyond their control. The free energy movement is rife with horror stories ranging from government theft of patents, to reputations destroyed, to the murder of untold numbers of brilliant scientists/inventors. We must all consciously and constantly rise above these tyrannical infringements, and create an environment for ourselves and our neighbors, and rediscover Natures Laws to be able to live and thrive. We must leave off responding in incredulity to what was done to us when we were told and believed we couldnt create free energy. We are now awake to the point that we know they were lying. Whos they? The elite for starters follow the money (watch THRIVE); J.P. Morgan couldnt put a meter on an energy plan for the world, and so destroyed any chance of that happening through several vicious attacks on Teslas reputation and livelihood basically got Teslas ideas out of the way for his own profit and power and maliciously destroyed the man (youtube: Teslas Autobiography). While the electric companies have told the people theirs is the only way to get electricity, and we are dependent on them, the truth is that we have been deprived of this alternative (quantum) energy source for close to 130 years. Morgans grip on the energy supply has not loosened one bit in all that time, in fact, you are probably paying more for electricity than ever before, all things being equal. So how do we effect our future now, and free ourselves and the generations to come after us completely from energy tyranny? Building the QEG is one way. It is a journey that requires you think deeply about processes that will, in turn, expand your senses to enable you to receive information from the quantum field of consciousness, or God if you prefer this reference. We believe we had Divine inspiration and help, which began with a burning desire to get off the grid and also do something significant for humanity. The timing is wonderful because, as of the writing of this, the entire planet is in turmoil as never before, and people will need to not only be self-sufficient, we will all need to live according to what is good for all (Ubuntu), and help each other for our continued evolution as species/planet. It is with great love that the QEG is offered to the world, and as you take on the task of building one, it is hoped that this becomes your path also: the mission of free energy for all! The next step we ask you to take on your journey, before and during building, is to listen to the discussion here: http://www.youtube.com/watch?v=3FqzTW7qh2U&feature=youtu.be with HopeGirl, Ralph and Marsha Ring, Fernando Vossa and the 3D Global Network. I am, in service to Gaia and its inhabitants, deeply grateful for this technology, and the opportunity to share it! Valerie Robitaille
SCHEMATIC
Parts List
Part Capacitors Ceramic Disc Capacitors Film Capacitors End Plates and Shrouds Fiberglass reinforced epoxy laminate (for 2 end plates) Fiberglass reinforced epoxy laminate (shrouds) Exciter Coil Clear Cast Acrylic Tube #10 Magnet wire (see generator core) V-Belts and Pulleys Goodyear 4L430 V-Belt 1 Groove, 3 x 7/8 bore, type A Pulley (Motor) 1 Groove 2.50 Pulley 7/8 bore type A (Generator) Drive Motor
Quantity
G10/FR4 G10/FR4
(1) sheet inch thick by 3 feet by 4 feet (2) 1/8 x 5.875 diameter
1 1 1
DC PM Variable Speed, 2500 RPM, 180V armature, 7/8 shaft, with base
Generator Core Spacer Blocks 1-1/2 x 1-1/2 x 4-1/2 Mica Tape 1.00 x 50YD Bonder for shaft/rotor 7387 Activator (use with bonder) Mica Plate NEMA 6 7/8 Three Bolt Flange Bearings Magnet Wire #10 Round HPT or HAPT Magnet Wire #20 Round Pulse Shield
16 1 1 1.75oz 1 2 ~620
~5200
Teflon tubing Fiberglass sleeving w/PVC for #10 HAPT wire (tubing) Tape, white, 1fiberglass, hitemp (outer wrap) Tape, black, 1 reinforced, high-strength Nomex Corner Insulation
TFT20019 NA005 (Alpha Wire) PF1308 RG48 (Intertape) 60020719 (Von Roll) Torelco
8 pieces (12 each) 8 pieces (12 each) 2 rolls 2 rolls 16 7/8 dia. x 11
Shafting 7/8 dia. x 11.0 long C1045 TGP Trukey w/standard 3/16 x 3/32 keyway 8 inch Bolts, - 28 thread, 1050095555 (Instock Grade 8 Fasteners) Electrical Terminals Assorted ring, spade, and quick connect terminals
Additional Parts Variac, 120/240V in, 0-280V out, 9.5 Amps Console Box w/panel Plexiglass sheet for mounting 2.5uF capacitors Electrical box 50 amp plug 50 amp receptacle Switch, start/run Bridge Rectifier Nuts Washers Frame and Base Angle aluminum
Type 1520 (STACO) 1456FG4BKBU (Hammond Mfg.) inch thick by 12 inches sq. 4 x 4
1 1 1 1 1 1 1 1 8 16
DPDT center off, 15 amp, 240V 600 volt, 25 Amp., quick connect terminals - 28 Grade 8 flat 1 x 1 x 4 feet. 1/8 thk.
POLARIS LASER LAMINATIONS Generator Core; Rotor TORELCO Toroidal winding service and complete core processing ready to ship FASTENAL Retaining (bonding) compound (Loctite 648: bonds rotor to shaft) with activator EIS Mica tape; 20 gauge Magnet wire S & W 10 gauge Magnet wire INDUSTRIAL SENSORS AND CONTROLS (ebay) Motor controller KBIC-240D variable speed DC motor controller; Resistor MOUSER Capacitors, Enclosures, Variac, Rectifiers, Start/Run switch JDS (ebay) V belt; pulleys EMCO PLASTICS End plates ASHEVILLE-SCHOONMAKER MICA Mica plates DISCOUNT STEEL Aluminum squares (spacers) BRIGHTON BEST 8 in. bolts MCMASTER-CARR Clear acrylic tube for exciter coil LAKE CITY ELECTRIC (ebay) Variable speed DC Motor (1 hp) THE BIG BEARING STORE 7/8 Three Bolt Flange Bearing w/set screws
Additional Parts High-temperature fiberglass tape (outer wrap) 4 x 4electrical box 50 amp plug 50 amp receptacle Black fiberglass sleeving (pvc-coated) Black mylar insulating tape Wood or welded steel tubular frame for base 12 - TPC Thomson / AVX Medium Power Film Capacitors Angle aluminum Start/run switch
MAJOR GENERATOR COMPONENTS Stator Rotor Bearings V belts Capacitors External exciter coil End panels/plates Magnet wire Drive motor Control box Frame and packaging Variac Inverter Pulleys
THE STATOR, or generator core, is made using 140 laminations of 24 gauge M19 C5 electrical steel forming a stack of 3 - inches, with a 4 pole configuration. Corresponding ROTOR with 2 poles. Both STATOR and ROTOR are tig welded in 4 places.
Shaft
Shaft contd*
* We didnt use the splines, rather, we used Loctite 648 retaining compound to bond the rotor to the shaft. This technique works very well with a close slip fit between the parts.
End Plates Fiberglass reinforced epoxy laminate (FR-4/G10) is used for end plate construction. End plates must be constructed of insulating material, but must also be structurally strong as they support all generator components, including bearings, shaft, rotor and stator. FR4 is the same material used to make circuit boards and is very strong, machinable, and dimensionally stable. Dimensions: End Plates: .500 Thk. G10/FR -4 15 X 16.5 with 15 radius and 2.450 center hole.
Bearings The bearings should have a narrow inner ring with set screws for attaching to the shaft. Housing is cast iron with a grease zerk for re-lubing the bearing. We used a 3-bolt flange type mount, but 2-hole or 4hole can also be used. Bearings are mounted on the inside of the end plates toward the rotor.
Capacitors The capacitors are a critical part of the system. The initial configuration on our prototype uses 12 caps, 2.5uF (microfarad) each. Each cap is rated for 2000V. These capacitors are wired in series in order to be able to withstand up to 25,000V in the primary circuit. The value and quantity of these capacitors will be adjusted to tune the frequency of the generator.
Variac The variac is used to control the drive motor speed which effectively controls the system power. Its used during construction/tuning, and prior to self-running set-up when it can be replaced with the smaller, lighter electronic motor drive circuit board.
Drive motor control circuit board The drive motor control circuit board is an industry standard SCR type DC motor drive manufactured by KB Electronics. The control board can be mounted in the console box we have included in the parts list, and is provided with a speed control potentiometer for adjusting motor speed.
CORE ASSEMBLY
This is the time to review the NOTICE and section on consciousness at the beginning.
We highly recommend ordering your generator set (stator and rotor) from an experienced professional lamination house. When your stator/rotor is welded and drilled, you are ready to bolt down the 8 spacers and wrap the core with 2 types of tape: Wrap 2 layers mica tape around the steel core (round part) followed by 1 layer of 1 reinforced, high-strength black tape. These 3 layers will bring the thickness needed for insulation to 17 mil (be very mindful at the corners of the pole pieces making certain there is no opening in the insulation for the wire to fall down into contact with the steel. If this happens, the coil will be short-circuited).
Installing Mica Plates After youve cut 16 c-shaped mica plates, install them on the top and bottom of each pole piece (front and back). We used a small amount of contact cement to hold them in place for the rest of the processing, but they can also be taped in place with the reinforced black mylar tape. These are installed after core taping and before winding.
Wiring You will need to commission a toroidal winding service. They might agree to process the entire core if you supply the materials (mica tapes and plates, corner insulation, aluminum spacers, bolts, outer taping, etc.). Proper winding is critical. Teflon sleeving is installed on the first complete turn of each winding of the #20 wire, and fiberglass/PVC sleeving on the #10 wire. Two coils of 3100 turns each of #20 wire are wound on opposing sides (left and right), and 2 coils of 350 turns each of #10 wire on the other sides (top and bottom). Leave about 3 feet of wire at the start of each winding and also at the finish for lead wires. Use enough sleeving to make sure the lead wires are completely insulated where they come through the back end panel. Be sure to secure the finish leads of each coil so that they dont unravel during handling.
Outer Wrap Taping Wrap a single layer of 1 white fiberglass tape tightly and securely around each coil making sure that all wire is covered and tape is butted up against the 4 pole pieces.
longer than necessary or a rotor imbalance can occur. Shrouds are used to quiet the windage noise generated by the spinning rotor.
Bearings Mount bearings to the inside of the front and rear end plates. Center each bearing on the 2.450 hole in the center of the plate. Drill the holes oversize for the mounting bolts. This is done to provide adjustability in the position of the shaft at final assembly. The bearings will have to be moved slightly to center the rotor in the bore of the generator. The gap between rotor and stator is very small (.010) and the rotor will need to be positioned so it does not rub on the stator bore. Only tighten finger tight at this time. We opted to bring the leads from the coils out directly through holes drilled in the rear end plate. You may decide to bring the leads out a different way. Here are the steps for our method: 1) Insert all 8 bolts into the rear end plate, then lay the plate down on a flat work surface with the bolts pointing up. The work surface should have a hole under the center hole in the end plate to provide clearance when the rotor is inserted. About 1 inches of clearance is needed below the plate. 2) With an assistant or two, place the fully processed core (about 90 lbs.) down onto the bolts. Slide the core all the way down into contact with the end plate. 3) Insert the short end of the rotor/shaft/shroud assembly through the stator bore and into the rear bearing. Let the rotor assembly drop gently to the bottom and place the front end plate with bearing over the bolts and shaft end. Tap into place with rubber mallet if necessary. Once plate is in contact with stator assembly, install washers and nuts and tighten securely. 4) With assistance, place the assembly upright onto the raised portion of the base. We used 5 lag bolts across the bottom of the end plates on each side to mount the assembly to the wood base/frame. Other methods could be employed. 5) Mount the drive motor to the base/frame. We mounted the shaft end of the motor onto the aluminum angle on the front of the base with one bolt to provide adjustability for belt tightening. We built a sliding mount for the rear of the motor using sheet metal parts, but sliding motor bases are commercially available that provide adjustability for proper belt tensioning. 6) When the motor is mounted to the base, install 3 pulley on motor shaft using set screws. 7) At this point the rotor position should be adjusted so that it spins freely inside the core without rubbing. This is where you may need to adjust the bearing positions repeatedly until the rotor spins freely. (The gap between the rotor and stator is .010 making this step a little delicate.) however, once the rotor is tightened in position it does not tend to move. Place the 2 pulley on the generator shaft at this time; it can be used to turn the rotor by hand while adjusting its position.
8) Place the V-belt over both pulleys and position pulleys as close to the motor and the generator as possible. Both pulleys should be positioned an equal distance from the faces of the motor and generator to assure that the belt runs true. 9) The variac can be mounted on the base at this time. We used two 1/4 20 x 1 bolts with nuts to mount the variac to the aluminum angle. After all the components are mounted on the base, wiring and testing will be performed using the variac. (After set-up and testing is completed, the variac can be replaced with the electronic motor control circuit board for less bulk and weight. The console box in the parts list can be used as an enclosure/control panel for the motor speed control board, and for mounting the DPDT start/run switch.) 10) With all components mounted on the base, wiring can begin. Please follow the schematic to make connections. We mounted a 4 x 4 electrical box on the base to support a large (50 Amp) receptacle to bring the power out of the generator. Wiring Notes: The generator output can be wired in series (220, 230-240V), or parallel (110, 115, 120V). For the series connection shown on the schematic, the start leads from each coil are connected together. This connection provides the highest voltage output from the windings. If using a parallel connection for lower voltage/higher current, be careful to connect the four leads with polarity opposed (start lead of one coil connected to finish lead of other coil). The variac we used can be wired for 120 or 240 volt input, and provides 0-280 volts output, at up to 9.5 amps. This is a versatile variac and can be used with either a 120 or 240 volt system. The output of the variac is connected to a 600 volt, 25 Amp full-wave bridge rectifier to power the variable speed DC drive motor.
Starting with the wiring setup as shown in the schematic, disconnect the primary coils from the series capacitor string on one end (disconnect capacitors). This will prevent resonance momentarily. Connect input power to the variac. We started with a full 240 volt series wired system, but parallel 120 volt wiring can also be used. Test mechanical assembly by spinning up the motor/rotor/belt and observing operation. Adjust variac voltage from zero to about through its range. The active rpm range is under 2500 rpm, so we dont need to spin very fast. Assure there is no stack rub (rotor scrubbing on stator), or other mechanical issues that need to be corrected for smooth operation.
When proper mechanical operation is assured, re-connect the series capacitor bank. The initial configuration of 12 (twelve) 2.5 uF, 2000 volt capacitors gives us .208uF, that will withstand up to 24,000 volts. This initial value should be in the range to produce resonance. As the machine spins up to resonance, the sound will change, and the rotor speed will lock into the resonant frequency. At this point any further increase of the motor speed control will change the speed only slightly, but the additional mechanical power (horsepower) will drive the core deeper into resonance, thereby increasing the power output. With a single control, the voltage and current (power) can be increased or decreased. As previously mentioned, the exciter coil is used to provide a conduction path through the quantum field (zero point) into the generator core. This has the effect of polarizing the core, which increases power output over time. After the QEG is first built, the spark gap on the exciter coil should be adjusted (with power off) to between .005 and .010. Start the generator and let it spark for 2-3 seconds, and repeat this 4 or 5 times. Do this whenever starting the generator for the first few weeks of operation.
Where is the energy this device is using coming from ? The quantum field How much overall power does the QEG produce? 10 KW (same design scaled up can produce 40 KW) If free energy devices work, why arent the electric companies using them? This should be obvious but in case you need a reference, please see: http://hopegirl2012.wordpress.com/ How is the QEG started up if it doesnt require fuel? All thats needed is to spin the machine up to resonance. At that point it will run itself. It can be started using existing electrical power if available, or a crank mechanism, or a battery powered motor-start system. A battery start system could also keep its own batteries fully charged, by tapping some power from the generator. How long will the QEG run? Indefinitely (or until parts wear out) How did the QEG improve upon Teslas work? This design adapts the linear, reciprocating element of the Patent, to a rotating element, and some electronics are employed for added stability; controlled amount of power and correct frequency range. Does the QEG slow down when more of a load is added? No its not that type of energy. Does the QEG emit radiation? No its not that type of energy. What form of energy does QEG use? Electromagnetic and atmospheric charge