Professional Documents
Culture Documents
ch06 Behrouz Forozan 4ed
ch06 Behrouz Forozan 4ed
Bandwidth Utilization:
Multiplexing and
Spreading
6.1 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Note
6.2
6-1 MULTIPLEXING
Whenever the bandwidth of a medium linking two
devices is greater than the bandwidth needs of the
devices, the link can be shared. Multiplexing is the set
of techniques that allows the simultaneous
transmission of multiple signals across a single data
link. As data and telecommunications use increases, so
does traffic.
Topics discussed in this section:
Frequency-Division Multiplexing
Wavelength-Division Multiplexing
Synchronous Time-Division Multiplexing
Statistical Time-Division Multiplexing
6.3
Figure 6.1 Dividing a link into channels
6.4
Figure 6.2 Categories of multiplexing
6.5
Figure 6.3 Frequency-division multiplexing
6.6
Note
6.7
Figure 6.4 FDM process
6.8
Figure 6.5 FDM demultiplexing example
6.9
Example 6.1
6.11
Example 6.2
Solution
For five channels, we need at least four guard bands.
This means that the required bandwidth is at least
5 × 100 + 4 × 10 = 540 kHz,
as shown in Figure 6.7.
6.12
Figure 6.7 Example 6.2
6.13
Example 6.3
Solution
The satellite channel is analog. We divide it into four
channels, each channel having a 250-kHz bandwidth.
Each digital channel of 1 Mbps is modulated such that
each 4 bits is modulated to 1 Hz. One solution is 16-QAM
modulation. Figure 6.8 shows one possible configuration.
6.14
Figure 6.8 Example 6.3
6.15
Figure 6.9 Analog hierarchy
6.16
Example 6.4
6.18
Note
6.19
Figure 6.11 Prisms in wavelength-division multiplexing and demultiplexing
6.20
Figure 6.12 TDM
6.21
Note
6.22
Figure 6.13 Synchronous time-division multiplexing
6.23
Note
6.24
Example 6.5
Solution
We can answer the questions as follows:
a. The data rate of each input connection is 1 kbps. This
means that the bit duration is 1/1000 s or 1 ms. The
duration of the input time slot is 1 ms (same as bit
duration).
6.25
Example 6.5 (continued)
6.26
Example 6.6
6.29
Example 6.7
Solution
We can answer the questions as follows:
a. The duration of 1 bit before multiplexing is 1 / 1 kbps,
or 0.001 s (1 ms).
6.32
Example 6.8
6.34
Example 6.9
Solution
Figure 6.17 shows the output for four arbitrary inputs.
The link carries 50,000 frames per second. The frame
duration is therefore 1/50,000 s or 20 μs. The frame rate
is 50,000 frames per second, and each frame carries 8
bits; the bit rate is 50,000 × 8 = 400,000 bits or 400 kbps.
The bit duration is 1/400,000 s, or 2.5 μs.
6.35
Figure 6.17 Example 6.9
6.36
Figure 6.18 Empty slots
6.37
Figure 6.19 Multilevel multiplexing
6.38
Figure 6.20 Multiple-slot multiplexing
6.39
Figure 6.21 Pulse stuffing
6.40
Figure 6.22 Framing bits
6.41
Example 6.10
Solution
We can answer the questions as follows:
a. The data rate of each source is 250 × 8 = 2000 bps = 2
kbps.
6.42
Example 6.10 (continued)
Solution
We can allocate one slot to the first channel and two slots
to the second channel. Each frame carries 3 bits. The
frame rate is 100,000 frames per second because it carries
1 bit from the first channel. The bit rate is 100,000
frames/s × 3 bits per frame, or 300 kbps.
6.44
Figure 6.23 Digital hierarchy
6.45
Table 6.1 DS and T line rates
6.46
Figure 6.24 T-1 line for multiplexing telephone lines
6.47
Figure 6.25 T-1 frame structure
6.48
Table 6.2 E line rates
6.49
Figure 6.26 TDM slot comparison
6.50
6-1 SPREAD SPECTRUM
In spread spectrum (SS), we combine signals from
different sources to fit into a larger bandwidth, but our
goals are to prevent eavesdropping and jamming. To
achieve these goals, spread spectrum techniques add
redundancy.
6.51
Figure 6.27 Spread spectrum
6.52
Figure 6.28 Frequency hopping spread spectrum (FHSS)
6.53
Figure 6.29 Frequency selection in FHSS
6.54
Figure 6.30 FHSS cycles
6.55
Figure 6.31 Bandwidth sharing
6.56
Figure 6.32 DSSS
6.57
Figure 6.33 DSSS example
6.58