HILTI System & Solution

expertise. in every case.
Drilling & Demolition Systems

Diamond Coring, Cutting & Sawing Systems
Cutting & Sawing
Screw Fastening Systems
Powder Actuated Systems
Pneumatic Fasteners
Mechanical & Adhesive Anchoring Systems
Strut & Hanger Installation Systems
Firestop Systems
Foam Systems
Maintenance Chemicals
Specials

P.O. Box 21148, Tulsa, OK 74121
Customer Service 1-800-879-8000
Fax 1-800-879-7000
In Canada call 1-800-363-4458
Hilti is an equal opportunity employer.
Hilti is a registered trademark of Hilti, Corp.
Copyright 2002 by Hilti, Inc. (US)
H600 00099510 05/02 LB, DBS
Customer Service
1-800-879-8000
Hilti Inc. (US), 5400 South 122nd East Avenue, Tulsa OK 74146
Fax (800) 879-7000 www.us.hilti.com
For reference and conversion charts see reverse.
www.us.hilti.com
*14001 US only
The data contained in this literature was current as of the date of publication. Updates and
changes may be made based on later testing. If verification is needed that the data is still current, please contact the Hilti Technical Support Specialists at 1-800-879-8000. All published load
values contained in this literature represent the results of testing by Hilti or test organizations.
Local base materials were used. Because of variations in materials, on-site testing is necessary
to determine performance at any specific site.
Hilti Tool Support Program
no hassle. no cost.*
* Some limitations apply.
Please contact Hilti for program details.
Customer Service 1-800-879-8000 I www.us.hilti.com I Systems and Solutions I 2002-2003
Laser Measuring & Positioning Systems
Table of Contents I Ordering Information I Hilti Centers I Help
Reference/Conversion Tables
Hilti Center Directory I Online Store Locator www.us.hilti.com/stores
Customer Service 1-800-879-8000 (M-F, 6:00 am - 8:00 pm CST)
for their knowledge of various trades.
1-800-879-8000
www.us.hilti.com
Hilti, Inc. (US) 1-800-879-8000

Direct access to highly trained customer
service teams that can provide immediate
service for:
Quotes
Processing orders
Pricing
Technical information
Order and inventory status
FT. LAUDERDALE
5601 N Powerline Rd, #102
Ft Lauderdale FL 33309
JACKSONVILLE
2517 Edison Ave
Jacksonville FL 32204
MIAMI
7210 NW 25th St
Miami FL 33122
ORLANDO
4374 L.B. McLeod Rd, #6
Orlando FL 32811
TAMPA
5011 W Hillsborough Ave, Ste K
Tampa FL 33634
Maryland
BALTIMORE
175 W Ostend St, Unit D
Baltimore MD 21230
BELTSVILLE
11602 Baltimore Ave
Beltsville MD 20705
Michigan
DETROIT
28190 Schoolcraft Rd
Livonia MI 48150
FLINT
3433 Lapeer Rd
Flint MI 48503
GRAND RAPIDS
640 44th St SW
Grand Rapids MI 49508
Minnesota
MINNEAPOLIS
2575 University Ave West, #120
St. Paul MN 55114
Missouri
ST. LOUIS
3637 N Lindbergh Blvd
St. Ann MO 63074
Georgia
North Carolina
ATLANTA MIDTOWN
1050 Marietta St NW
Atlanta GA 30318
ATLANTA SUPER
6155-H Jimmy Carter Blvd
Norcross GA 30071
CHARLOTTE
801 Clanton Rd, Ste 113
Charlotte NC 28217
RALEIGH
628 Hutton St, Ste 105
Raleigh NC 27606
CINCINNATI
2736 E Kemper Rd, Bldg A
Cincinnati OH 45241
CLEVELAND
5400 Transportation Blvd
Garfield Heights OH 44125
COLUMBUS
818 Rose Ave
Columbus OH 43219
Oklahoma
OKLAHOMA CITY
411 N Meridian
Oklahoma City OK 73107
TULSA
10660 E 31st St
Tulsa OK 74146
Oregon
PORTLAND
316 SE Taylor St
Portland OR 97214
Pennsylvania
PHILADELPHIA
1618 S Columbus Blvd
Philadelphia PA 19148
PITTSBURGH
1301 Beaver Ave
Pittsburgh PA 15233
18
18
16
16
2.1-3.4
18
18
18
16
16
14
3.5-5.0
18
18
16
14
12
12
18
16
14
14
12
10
16
14
12
10
10
12.1-16.0
14
12
10
10
16.1-20.0
12
12
10
20.1-25.0
12
10
10
Utah
5.1-7.0
SALT LAKE CITY

2180 South 300 West, #108
Salt Lake City UT 84115
7.1-12.0
Virginia
CHESAPEAKE
200 Tintern Court, 101
Chesapeake VA 23320
FAIRFAX
2800 Gallows Rd, Ste F
Vienna VA 22180
RICHMOND
4203 W Broad St
Richmond VA 23230
Washington
KIRKLAND
11251 120th Ave NE
Kirkland WA 98033
SEATTLE
555 S Lander St, Ste 1
Seattle WA 98134
Wisconsin
MILWAUKEE
1461 S 108th St
West Allis WI 53214
Puerto Rico
PUERTO RICO
Calle Calaf #31, Parque Ind. (Tres
Monjitas)
Hato Rey PR 00918
Rhode Island
PROVIDENCE
155 Jefferson Blvd
Warwick RI 02888
expertise. in every case. Customer Service 1-800-879-8000 (M-F, 6:00 am 8:00 pm CST) H600
Fractional to
Decimal
Conversion
Fraction Decimal
of an Inch Equivalent
1/64
1/32
3/64
1/16
5/64
3/32
7/64
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
180
170
18
110
BOSTON
60 Arsenal St
Watertown MA 02472
Ohio
18
0.015
0.031
0.046
0.062
0.078
0.093
0.109
0.125
0.140
0.156
0.171
0.187
0.203
0.218
0.234
0.250
Screw
Diameter Gauge
90
Florida
Massachusetts
0-2.0
Fraction Decimal
80
Hilti team members are highly trained and known worldwide
NEW ORLEANS
5630 Jefferson Hwy
Harahan LA 70123
Extension Cord Length
25' 50' 75' 100' 150' 200'
#6
#8
#10
#12
#14
0.138
0.164
0.190
0.216
0.242
70
manufacturers, sells and supports their products directly.
Louisiana
Tool
Ampere
Rating
60
HARTFORD
304 Murphy Rd
Hartford CT 06114
STAMFORD
87 Harvard Ave
Stamford CT 06902
LOUISVILLE
4524 Bishop Lane
Louisville KY 40218
Extension Cord Ordering Information

Hilti extension cords are UL Listed and meet
OSHA requirements for indoor and outdoor use.
For product information, see Drilling & Demolition (2)
or Diamond Coring, Cutting & Sawing (3)
40
Connecticut
Kentucky
BUFFALO
1000 Young St, Ste 490
Tonawanda NY 14150
HAUPPAUGE
11 Central Ave
Hauppauge NY 11788
MANHATTAN (Downtown)
76 9th Ave
New York NY 10011
MANHATTAN (Uptown)
1819 Second Ave
New York NY 10128
QUEENS
40-15 Northern Blvd
Long Island City NY 11101
30
company in the industry who researches, develops,
KANSAS CITY
1845 Foxridge Drive
Kansas City KS 66106
WICHITA
1703 SW Blvd
Wichita KS 67213
New York
20
DENVER
5855 Stapleton Dr North,
Unit A-160
Denver CO 80216
Kansas
contact with our customers is so important. Hilti is the only
INDIANAPOLIS
4086 Pendleton Way
Indianapolis IN 46226
Colorado
Indiana
160
AUSTIN
9010 IH 35 North, #116
Austin TX 78753
DALLAS
13635 Stemmons Fwy, #100
Farmers Branch TX 75234
EL PASO
7230 Gateway Blvd E, Unit C
El Paso TX 79915
FORT WORTH
2400 Meacham Blvd,
Ste G
Fort Worth TX 76106
HOUSTON NORTH
13240 Hempstead,
Ste 224
Houston TX 77040
HOUSTON SOUTH
8555 Knight Rd
Houston TX 77054
SAN ANTONIO
2411 NE Loop 410,
Ste 102
San Antonio TX 78217
150
Texas
HACKENSACK SUPER
263 S River St
Hackensack NJ 07601
PERTH AMBOY
788 Convery Blvd
Perth Amboy NJ 08861
BURBANK
2907 Empire Ave
Burbank CA 91504
LOS ANGELES
3310 Garfield Ave
Commerce CA 90040
OAKLAND
842 66th Ave
Oakland CA 94621
ORANGE
1070 N Batavia Ave,Ste D
Orange CA 92867
SACRAMENTO
3500 Power Inn Rd, Ste C
Sacramento CA 95826
SAN DIEGO
8303 Clairemont Mesa Blvd, Ste
101
San Diego CA 92111
SAN FRANCISCO
180 Pennsylvania
San Francisco CA 94107
SAN JOSE
691 E Brokaw Rd
San Jose CA 95112
140
New Jersey
California
130
NASHVILLE
561 Murfreesboro Rd
Nashville TN 37210
120
Tennessee
LAS VEGAS
5480 S Valley View Blvd, #140
Las Vegas NV 89118
100
Nevada
CHICAGO NORTH
451 S Busse Rd
Elk Grove Village IL
60007
CHICAGO SOUTH
6343 W 95th St
Oak Lawn IL 60453
50
Illinois
PHOENIX
325 S 48th St, Ste 106
Tempe AZ 85281
An undersized cord will cause a drop in voltage,

resulting in loss of power and overheating of the
tool. Use an extension cord heavy enough to carry
the current your tool requires. A heavier gauge
extension cord is required as the distance from the
electrical supply outlet increases.
To determine the proper size and length of extension cord, first refer to the ampere rating shown on
the tool nameplate. Apply this value to the chart at
right showing the recommended American Wire
Gauges (AWG) for use with electric tools. Always
use UL Listed extension cords. When in doubt, use
the next heavier gauge (the smaller the gauge, the
heavier).
0
10
Millimeters
Arizona
Choosing Extension Cord Wire Size (AWG)
COLUMBIA
1424 Bluff Rd
Columbia SC 29201
OMAHA
8310 F St
Omaha NE 68127
HONOLULU
1199 Dillingham Blvd
Honolulu HI 96817
call.
ANCHORAGE
7655 King St
Anchorage AK 99518
drive our actions which is why close personal
South Carolina
Metric Conversion Ruler
at Hilti, our customers requirements
Nebraska
Inches
0
there
Hawaii
Wire Size
Hilti is
Alaska
click.
visit.
Online www.us.hilti.com
Instant and convenient, our website offers:
Technical library with download
function
Design Centers for Anchoring, Decking
and Firestopping
Interactive product advisors
Product information
Maps to local Hilti Center locations
Now available, easy online ordering
see website for details
CORDLESS
DIRECT
FASTENING
DRILLING &
DEMOLITION
DIAMOND
CORING
& SAWING
Local Hilti Centers provide convenience

with:
Hands-on product demonstrations
of the latest in Hilti innovation
On hand inventory
Training/certification
FIRESTOPPING
SAWING &
GRINDING
SCREW
FASTENING
ADHESIVE &
MECHANICAL
ANCHORING
MEASURING
SYSTEMS
Customer Service 1-800-879-8000 (M-F, 6:00 am 8:00 pm CST) | www.us.hilti.com
onsite.
More than 800 Sales Representatives

and specialists come to you with:
Application solutions
Training
Hands-on product demonstrations
of the latest in Hilti innovation
Technical support
INSTALLATION
SYSTEMS
More Productivity with Less Administration
Hilti Fleet
Management
The Innovative
Tool Management Solution
For companies with large tool fleets, the acquisition,

maintenance and management of tools can be a major
ongoing expense and inconvenience. With the Hilti Fleet
Management Program*, your company can benefit from a
new tool fleet, less downtime, more reliability and a
predictable monthly cash flow, without a large up-front
capital investment.
The Hilti Fleet Management Program can help reduce your
total tool ownership costs. With Hilti Fleet Management,
youll avoid surprises for unscheduled fleet upgrades and
maintenance costs. There is no huge up-front cash outlay
for fleet upgrades and your costs are limited to one payment
per month, which includes tool purchases and repairs. This
allows you to spread your exact tool costs over several
years, providing better productivity with less administration.
Since this is a Hilti Full Service program, tools that need
servicing can immediately be sent in for repair at no
additional cost. This means no more estimates,
purchase orders or internal delays saving you time
and money. Your Fleet Management Program tools
are given priority status at our Repair Centers, so they
are repaired and sent back to you as quickly as possible.
For more than 50 years, Hilti has been a leader in
pioneering and developing professional quality
tools for the construction market. A constant
focus on product and service improvement
allows us to provide better tools for our
customers while increasing their
productivity. The Fleet
Management Program is another
way to better satisfy customer
needs as the industry changes.
*Some limitations apply.
Contact Hilti for details.
1-800-950-6629
With Hilti Fleet Management you can afford to

acquire the tools you need to generate cash flow
without a large up front capital investment.
How The Hilti Fleet Management

Program Works For You.
New Tool Fleet You get the latest in safety and work saving
technology direct from the manufacturer.
Less Downtime New tools reduce downtime keeping work flow
smooth and on track.
Predictable Cash Flow One monthly fixed cost for tool purchases,
repair and replacement.
More Reliable With new tools youll work longer by reducing the
likelihood of costly break downs.
Less Repairs Fewer repairs mean less hassle on the job site and
reduced administration.
More Productivity Reliable, top-of-the-line tools mean increased
worker productivity and getting the work done quicker.
Systems & Solutions
Hilti is
there
whats
New Products from Hilti
Page vi
Measuring Systems
Section 1
Section 2
Section 3
Wood Cutting & Sawing, Specialty Drilling
Section 4
Screw Fastening & Drill Driver Systems
Section 5
Direct Fastening Systems
Section 6
Anchoring Systems
Section 7
Installation Systems
Section 8
Firestop Systems
Section 9
1-800-879-8000
www.us.hilti.com
*14001 U.S. only
The data contained in this catalog was current

as of the date of publication. Updates and
changes may be made based on later testing. If
verification is needed that the data is still current, please contact the Hilti Technical Support
Specialist at 1-800-879-8000.
Please see Terms and Conditions of Sale.
All published load values contained in this catalog represent the results of testing by Hilti or
test organizations. Local concretes were used.
Because of variations in materials, on-site testing should be performed to determine performance at any specific site.
All Hilti Chemical Products and Chemical
Anchors have the expiration date stamped on
each individual product. The product is suitable
for use through the last day of the month indicated, provided storage instructions are followed.
Foam & Construction Chemicals
Terms & Conditions of Sale

Hilti Center Directoryinside back cover
Appendix
Section 10
Tool Repair
2 Years.
Full Service.
No Charge.
*
Hilti Tool Support

Program
For years, Hilti has been devoted to making reliable and rugged
tools to withstand your demanding jobsite activity.
Our customers trust Hilti to provide durable and
reliable tools, to stand up to even the most
demanding jobs. We also know that sometime tools
will need service or repair. With Hiltis goal of providing
Total Customer Satisfaction we have developed a Full Service
Tool Support Program with you in mind.
The Hilti Full Service Tool Support Program includes:

Transportation of the tool; to and from the repair center
Maintenance service
Repair and replacement of all defective parts, including labor
Functional test; adjustment and safety check after any repair
Worry-Free
FREE repairfor up to 2 years*
Quick and reliable repair
No worriesclear and defined Tool Support coverage
As of January 2001, with the purchase of

the following tools you will receive FREE
service and repair for up to 2 years*:
2 Years
Rotary & Combihammers
Breakers
Diamond Coring Systems
Laser Positioning Systems
Ferroscan
1 Year
Diamond Cutters
Screwdrivers
Rotary Drills & Hammer Drills
iv
Look for the Full Service icon located on

product pages for tools supported
by the Full Service Tool Support Program.
Some limitations apply.
Please contact Hilti for details.
1-800-879-8000
* Some limitations apply. Misuse, failure to comply with the operating instructions or damage
caused by undue force (dropping or impact damage, acts of God, etc.),manipulation of the tool
or its parts by unauthorized persons are not covered by this Full Service Tool Support Program.
At the discretion of Hilti, Inc. discontinued models may or may not be included in the repair
program. Select accessories are not covered, please contact Hilti for details.
Tool Repair
Hilti Tool Repair

Program
*
*Typical turnaround time
R e p a i r
P r o g r a m
The Hilti Top Stop Tool Repair Program limits exposure to high
repair costs by establishing a maximum repair billing for
specified tool models. If tool repair charges exceed the standard Top
Stop limit for the tool the customer is billed only the amount allowed by
Top Stop for that tool. If repair charges are less than the Top Stop
amount the customer is only billed for the work completed.
Whether its a tool requiring regular service to provide peak
performance and long life or a tool in need of repair, Hilti Repair
Centers are equipped to complete repairs to the highest standards. Hilti
Repair Technicians utilize state-of-the-art technology and equipment
designed specifically for Hilti machines to complete high quality, quick
turnaround repairs. All tools are inspected and tested before being
returned to the customer.
If you have a Hilti tool requiring service, contact Hilti Customer Service.
The Hilti ARS program is a convenient UPS pick-up service designed to
get your Hilti tool to the repair shop quicker for repair and back on the
job sooner.
Total Tool Service

Easy as 1,2,3
1-800-879-8000
Ext. 5861
For all your Hilti tool service needs, contact Hilti Customer
Service at 1-800-879-8000, Monday thru Friday, 6am-8pm
Central Standard Time.
whats
from
Hilti GX 100 Gas-Driven Fastening System
Charge Up Your Work. Not Your Batteries.
No
B
atte
to Charger. y
The Right System for All Your Interior Finishing Fastening Needs. GX 100
The new high-performance system from Hilti with no battery to charge. Ever.
EVER.
Advantages
Convenient No battery to charge
Reliable Fasten into steel & hard concrete with ease & confidence
Versatile Wide range of applications and consumables
Fast You be the judge
Technical Data
Dimensions (LxWxH)
16.75" x 6.9" x 14.6"
Magazine Capacity
40 collated fasteners
Tool weight
9.15 lb Loaded with fasteners
Power Source
GC 12 (gas canister)
Fastener Range
1/2" to 1-5/8"
Steel
For beams and columns
Repetitive fastening of metal track
and hat-track, Z brackets and slip
track
Easily Fasten Into

Steel & Hard
Concrete
Concrete
For floors, walls and ceilings
Repetitive fastening of metal
track,hat-track and wood
Metal profile fastening to walls for
suspended ceilings
Concrete Block
Fastening of metal track and hat-track
GX 100 Gas-Driven Fastening System
Item No.
Description
00338047
GX 100 Gas-Driven Fastening Tool
Supplied in an impact resistant plastic Hilti case with

attachable support leg, ear protectors, safety glasses,
cleaning cloth and operating instruction manual.
Accessories
Item No.
Description
00378586
00378587
00378588
00379693
X-GM 40 Nail Magazine

X-100 SL Support Leg
X-100 TN Nosepiece
GC12 Gas Canister (750 fastenings)
Item No.
Description
00338872
00340227
00338875
00340229
00338878
00338881
X-EGN 14MX Combo

X-GHP 18MX Combo
X-GN 20MX Combo
X-GN 27MX Combo
X-GN 32MX Combo
X-GN 39MX Combo
1/2"
11/16"
3/4"
1"
1-1/4"
1-9/16"
Fasteners Package content: 750 pins (collated instrips of 10)

Nail
Length (in.)
Typical Base Material
Steel
Hard Concrete
Concrete
Concrete and Block
Concrete and Block
Concrete and Block
www.us.hilti.com
for latest product information
vi

Easily Fasten Into Steel & Hard Concrete
No
B
atte
to Charger. y
EVER.
Adjustable
& removable
tool nose.
40 nail
capacity
magazine.
Removable
magazine with
quick release
lever.
www.us.hilti.com
vii
whats
from
WSR 900 Reciprocating Saw
Grip it & Rip it: The ultimate in handling, performance and durability.
Advantages
Handling
Innovative, lightweight, design
allows comfortable us of the
tool in a variety of working
positions
Performance
Efficient gear design allows
more of the power input to
be delivered to the blade and
cutting surface
Durability
Metal gearing is carburized
extending the life of the tool
* Some limitations apply. Contact Hilti for details.
Technical Data
Amps
8.5 / 8.5 Plus Smart Power (900-PE)
Watts
900
No Load SPMs
0-850,0-2700
Weight
6.3 lb / 7.2 lb (900-PE)
Stroke Length
1-1/4 in.
Switch
Variable Speed
Speed Adjustment
1-6 settings
Blade Change
One-handed, keyless blade change
Adjustable Shoe
7 positions, Removable
Cord Length
15 ft
Introducing the first in a

growing line of cutting tools for
the professional user.
The WSR 900-PE Reciprocating Saw
incorporates the Smart Power
System; providing consistent power
when under load, maintaining the
stroke rate.
*Case not included with

all models.
See product description
for details.
Smart Power System

A combination of efficient gears
and load management sensor
provides constant blade speed when
under load.
Anti-Vibration
With 20% less vibration than
competitors, the user experiences
smooth, even cutting , resulting in
reduced fatigue.
Orbital Function
For faster, more aggressive cutting
into wood and other soft materials.
WSR 900-PE shown in

use with optional Pipe
Clamp Adapter sold below.
Ordering Information
Item No.
Description
00376748
WSR 900 Reciprocating Saw

Supplied with 1 WSR 900, complimentary 6" x 6T wood
blade, operating instructions in a cardboard box
00378275
WSR 900-PE Reciprocating Saw

Supplied with 1 WSR 900-PE, complimentary 6 x 6T wood
blade, operating instructions in an impact resistant plastic
Hilti case
Accessories
Item No.
Description
00378888
Pipe Clamp Adapter

For use with WSR 900 or WSR 900-PE for precision pipe
cutting at 90 degree angle.
www.us.hilti.com
viii

Metal Cutting
Bi-Metal Reciprocating
Saw Blades
The blades that give you superior
cutting performance and longer life.
Blade Applications
Hilti reciprocating blades are designed for many different construction
conditions and building materials. Typical applications include cutting:
Wood, including nail-embedded
wood
Heavy and light duty gauge metal
Plastic
Cast aluminum
Non-ferrous metals
Bar-stock and angles

Pipe, channel
Thick conduit
All types of composition material
(e.g., plasterboard, sheetrock,
rubber, fiber)
To help you select the appropriate Hilti

blade, remember these general rules:
For faster cutting, use fewer teeth per inch.

For thicker material, use fewer teeth.
For very hard materials, use more teeth to
improve performance.
For a smoother finish, use more teeth.
Item No.
Description: Metal Cutting
00205993
96300109
00205995
00253240
00205996
00253241
00304685
00205997
00253242
00304686
00205998
00253243
00304687
00205999
00253244
00304688
02006315
00253245
00304689
00374336
00304673
00374337
00304674
Wood and Nail
R-MB 4" X 18T Metal cutting

Quantity
Item No.
Description: Wood and Nail
00205989
00253236
00304682
00205990
00253237
00304683
00205991
00253238
00304684
Combination
R-NB 6" X 6T Wood and Nail

5
50
5
50
5
50
500
5
50
500
5
50
500
5
50
500
5
50
500
5
50
5
50
Quantity
Item No.
Description: Combination
00374338
00304675
00374339
00304676
00374340
00304677
Demolition
R-CB 6" X 10/14T Combination

R-CB 6" X 10/14 Combination
5
50
500
5
50
500
5
50
500
Quantity
Item No.
Description: Demolition
96300041
03004678
00374341
00304679
96300039
00304680
Drywall/Plaster
R-DB 6" X 6T Demolition

5
50
5
50
5
50
Quantity
Item No.
Description: Drywall/Plaster
00374342
96300090
R-PB 6" X 6T Drywall/Plaster

R-PB 6" X 6T Drywall/Plaster
3
25
3
25
3
25
Quantity
5
50
www.us.hilti.com
ix
whats
from
TE 46 Combihammer
Put the power where it counts with the TE 46 and TE-T bits.
TE-T
Advantages
Up to 40% better drilling
performance.
Up to 30% better chiseling
performance .
Ergonomic design for more
operator comfort.
Technical Data
Power Input
1050 W
Voltage
115 V
Hammering Speed Under Load

Many hammer drills are
powerful enough, but
only the Hilti TE 35 and
the new TE 46 use
the exclusive
TE-T connection
end to get more
Competition
power out of the drill
and into the bit, where it
counts. Perfectly matched to
harness the strength of the powerful
motor, TE-T bits pack a punch that
leave other bits in the dust.
Setting I: 02046 blows/min

Setting II: 02886 blows/min
New Hilt
Combihammi ers
Single Impact Energy

Setting I: 2.6 ft-lb
Setting II: 5.2 ft-lb
Out-Perform
& Out-Last
the
Speed Loaded
Setting I: 260 rpm
Setting II: 484 rpm
Machine Weight
13.9 lb
Dimensions (LxWxH)
18.4" x 3.7" x 9.4"
Drilling performance
with 3/4" bit 6.3 in3/min
TE-T: Higher productivity & longer life

1/4"
CONCRETE
9/16"
3-9/16"
7/8"
The Hilti TE-T medium mass system combines the

high torque transmission of the SDS Max with the
reduced mass of the SDS+ for better impact
transmission. This combination creates an insert tool
that more efficiently drills at a reduced wear rate
across a wide diameter range.
TE-T: For a lighter combihammer

Less weight means better handling. As the TE-T
connection end is smaller than the SDS Max (TE-Y),
the TE 46s hammering mechanism is more compact,
reducing the machine weight by about 2 lbs.
compared to other combihammers.
R e p a i r
P r o g r a m
Ordering information
www.us.hilti.com
for Hilti product information
Item No.
Description
00374069
TE 46 DLX grounded 115V

Comes with 13 ft. supply cord, impact resistant plastic
Hilti case, Hilti grease, cleaning cloth and operating
instructions.
Drill Bits see page:
2.33
x

TE 56 Combihammer
TE 56 and TE 56-ATC Deliver Maximum Performance
Advantages
TE-Y
(SDS Max)
Up to 50% longer run time.

Covered by Hiltis no worries,
no additional cost, 2-Year Full
Service Warranty.
ATC Active Torque Control
on TE 56-ATC for added
operator protection.
TE 56-ATC has 3rd speed for
drilling without hammering.
Less vibration for more
comfortable working.
ATC Active Torque Control:
Lets you work easier

New Hilt
Combihammi ers
Out-Perform
& Out-Last
the Competit
The TE 56 Combihammer is the top

performer in its class. Designed and built
to take long periods of hard use in stride,
ion
its reliability is second to none. And with
the added feature of the ATC Active Torque
Control System, the TE 56-ATC provides additional
operator protection not available in competitive tools.
With a wide variety of tough, long lasting bits and chisels with the durable
TE-Y connection end, the TE 56 could quite possibly be the hardest working
tool on your job.
A Hilti patented feature, the ATC

(Active Torque Control) system
stops the TE 56-ATC in a fraction
of a second if it senses the tool
beginning to rotate too quickly,
providing additional protection for
the operator.
Technical Data
Power Input
1100 W
Voltage
115 V
Hammering Speed Under Load

Setting I: 02046 blows/min
Setting II: 02886 blows/min

Setting I: 2.6 ft-lb
Setting II: 5.2 ft-lb
Speed Loaded
Setting I: 260 rpm
Setting II: 484 rpm
Rotary Only (TE 56-ATC): 720 rpm
Machine Weight
TE 56: 13.9 lb
TE 56-ATC: 15.2 lb
Dimensions (LxWxH)
18.7" x 3.7" x 9.4" (10.2" ATC)
with 3/4" bit 6.3 in3/min
1/2"
CONCRETE
5/8"
Item No.
Description
00374056
TE 56 DLX grounded 115V
3-9/16"
1"
Steel: Up to 1/2"
Wood: 3/8" to 1-1/4"
Comes with 13 ft. supply cord, impact resistant plastic Hilti

case, Hilti grease, cleaning cloth and operating instructions.
R e p a i r
P r o g r a m
www.us.hilti.com
00374040
TE 56 ATC grounded 115V

Comes with 13 ft. supply cord, impact resistant plastic Hilti
case, Hilti grease, cleaning cloth and operating instructions.
2.38
Chisels see page:
2.40
xi
whats
from
Measuring
Systems
PD 22 Range Meter
PD 28 Range Meter
see page:
see page:
1.5
1.6
PR 16 & PR 16-IF
Rotating Lasers
see page:
1.13
www.us.hilti.com
xii
Drilling &
Demolition
Systems
TE-SP
Self Sharpening
Chisels
see page:
2.49
TE 6-S
Rotary
Hammer
see page:
2.15
TE 6-C
Rotary
Hammer
see page:
2.16
xiii
whats
from
Diamond Coring,
Cutting & Sawing
Systems
DD 130 Diamond
Coring System
see page:
3.18
DG 150 Diamond
Grinding System
see page:
3.47
HG 500-D
see page:
3.49
www.us.hilti.com
xiv
Screw Fastening
& Drill Driver
Systems
SF 180-A Cordless
Drill/Driver
see page:
SF 4000-A
Battery Drywall
Screwdriver
see page:
5.8
5.10
Anchoring
Systems
HIT-ICE System
see page:
7.12
www.us.hilti.com
xv
whats
from
Installation
Systems
MQN Pushbutton
see page:
8.10
3D System
see page:
8.12
MQW-Q2
Preassembled
90 Angle
see page:
8.13
www.us.hilti.com
xvi

www.us.hilti.com
Visit Hilti online for the latest in product
information, Hilti News and Special Events.
Design Centers for Anchoring, Decking and
Firestopping
Product Technical Guide
Firestop Technical Guide
For complete technical information, refer to the

Hilti North America Product Technical Guide.
Anchoring
Screw Fastening
Powder Actuated Fastening
Installation Systems (Strut & Hanger program)
For complete firestop technical information,

refer to the Hilti Firestop Systems Guide
Technical
Resources
How can I get copies of Hilti

Technical Publications?
Please contact Hilti Customer Service.
1-800-879-8000
xvii
NEW
Hilti PD 22 / PD 28 Laser Range Meters
What your
tape
measure
cant do...
See page 1.3
Measuring Systems
Range Meters
NEW !
NEW !
PD 22
PD 28
Page 1.5
Page 1.6
Plumb Laser
PM 22
Page 1.9
Multi-Directional
PM 24
Page 1.10
Rotating Laser Systems

NEW !
PR 16 & PR 16-IF
PR 60
Page 1.13
Page 1.14
Tripods/Leveling Staffs
NEW !
Heavy Duty Tripod PA 911

Short Tripod PA 920
Large Tripod PA 932
Leveling Staff PA 960 (fractional/metric)
Leveling Staff PA 961 (fractional)
Leveling Staff PA 962 (feet/tenths)
Leveling Staff PA 951 (metric)
Page 1.17
Page 1.17
Page 1.17
Page 1.18
Page 1.18
Page 1.18
Page 1.18
Detection Systems
Multi-Detector PS 20
Ferroscan FS 10
Page 1.19
Page 1.21
Measuring Systems
System
Application
Page
tool22
PD
Measure distances to 500' (150m) with an

accuracy of 1/12" (2mm)
Measure to inaccessible places without contact
Calculate areas and volumes
Measure heights without the need for ladders,
scaffolds or lifts
Estimate material requirements
000
1.5
Measure distances to 500' (150m) with an

accuracy of 1/12" (2mm)
Measure to inaccessible places without contact
Calculate angles and areas of triangles
Measure and calculate sloped objects
Calculate circumference
Lay out predefined distances
Store and identify 1,000 measurements
1.6
Accessories:
000
1.8
NEW!
Class
PD 28
tool
Range Meters
NEW!
Tape
Measure
PD 22
One person operation
Accuracy of 1/12" over entire range
tool
Measuring short distances (4"+)
Class
Dust and rain protected for jobsite use
Measure to inaccessible areas without contact

Measure lengths/heights indirectly
PD 28
Calculate area and volume at the touch of a button
Accurate measuring from corners with the built in spike
Integrated bubble for precise horizontal measurements
Measure perimeters and offsets
Calculate slopes (roofs, pipes, ceilings, etc)
000
Accessories:
000
Determine angles of corners and other inaccessible places
Store and identify measurements for later processing
Export measurements to a PC in Microsoft Excel for analysis
tool
PM 22
Plumb Laser
Class
Accessories:
000
What your tape measure cant do

Setting out distances and marking positions
1.3
Accessories:
1.8
000
000
Accessories:
000
Transferring points from floors to ceilings for:

- Alignment of upper and lower drywall track
- Marking installation points for duct work,
piping, sprinkler systems, electrical boxes and
lighting applications
Plumbing window and door frames, steel beams,
formwork, tilt wall construction, etc
1.9
Accessories:
1.12
Measuring Systems
Application
PM 24
Horizontal leveling
Laying out right angles
Plumbing window and door frames, steel beams,
formwork, tilt wall construction, etc
Transferring points from floors to ceilings
1.10
Horizontal alignment of suspended ceilings,

electrical fixtures, setting benchmarks, etc.
Vertical alignment of drywall track, water/sprinkler
pipes, electrical fixtures, HVAC ductwork, etc.
Lay out of 90 degree and 180 degree right angles
Lay out of conveyance systems, piping, concrete
forms on an inclination
1.13
Pouring and compacting concrete foundations

Alignment of formwork, floors and decks
Leveling work in general construction and civil
engineering
Excavation of foundations
1.14
Multi-Directional
System
PR 16 & PR 16-IF
Rotating Laser Systems
NEW!
PR 60
Page
Accessories:
1.12
Accessories:
1.16
Tripods:
1.17
Leveling
Staffs:
1.18
Accessories:
1.16
Tripods:
1.17
Leveling
Staffs:
1.18
Detection Systems
PS 20
Ferroscan FS 10
Locate and identify rebar, copper and aluminum

pipes in concrete
Perform precautionary checks before drilling
Check the concrete cover over reinforcement
Determine the presence of live electrical wires
1.19
1.21
Locate reinforcement in concrete up to 7

Get an exact picture of the rebar in concrete
Avoid cutting statically relevant reinforcement
Verify coverage of concrete over reinforcement for
quality inspections or renovation work
Calculate the average concrete cover over large
areas
Accessories:
1.20
Accessories:
1.22
1.4
Range Meters
PD 22 Range Meter
Instant Distance
NEW!
Technical Data PD 22
Accuracy
Typically 1/12"
Range
500 ft (150 m)*
Laser
635 nm, class 2 (IEC 825-1), Class II
(FDA 21 CFR)
Measuring functions
Single and continuous measurement
Data memory
Last 3 measurements
Protection class
IP 54
Operating temperature range

14F to 122F (10C to 50C)
Battery Life
Approx. 10,000 measurements with 2
type AA batteries
Measure distances and calculate areas and volumes

accurately with one person.
Measure heights safely and easily without ladders, lifts or

scaffolding.
Dimensions (LxWxH)
6-1/2" x 2.6" x 1.8"
(165 mm x 67 mm x 47 mm)
* The maximum range depends on target
surface reflectivity and brightness of ambient
light. The PA 412 target plate should be used
if the light reflected by the target is
insufficient.
The Hilti PD 22 Laser Range Meter measures

distances, offsets and calculates areas and
volumes faster and more accurately than
traditional tape measures. Just aim the laser
at the target, press the measuring key and the
PD 22 shows the distance. Whether
measuring heights that used to require two
people using ladders or lifts, measuring difficult
to reach areas or simply distance measuring,
the PD 22 makes it safe, fast and accurate.
Features
C A U T I O N
LASER RADIATION DO NOT
STARE INTO BEAM
620-690 nm/ 0.95 W max.
CLASS II LASER PRODUCT
Laser beams are shown symbolically in

the illustration as red lines.
Measure up to 500' without contact

Highly accurate to 1/12" over entire
operating range
Calculation functions: addition, subtraction
and multiplication
Pythagoras function for measuring heights
indirectly
Integrated bubble level for precise
horizontal measurements
Built in spike for accurate measuring from
corners
Advantages
www.us.hilti.com
Ordering information:
Fast and accurate ONE PERSON operation

Calculate areas and volumes at the touch
of a button
Measure to inaccessible places without
contact
Measure more safely and efficiently
without the need for ladders, scaffolding
or lifts
1.7
Accessories see page:
1.8
1.5
Range Meters
PD 28 Range Meter
NEW!
When Close Enough Isnt
Technical Data PD 28
Accuracy
Typically 1/12"
Range
500 ft (150 m)*
Laser
635 nm, class 2 (IEC 825-1),
Class II (FDA 21 CFR)
Measuring functions
Single and continuous measurement
Data memory
1000 values, in structured form with
identity tags
Data transfer
To PC in Microsoft Excel format
Protection class
Measure heights indirectly without ever leaving the ground.
Measure to inaccessible places even when the laser spot is

no longer visible using the PA 421 Telescopic Sight.
One person can calculate angles, sloped distances, circumferences,

averages and set out predefined distances at the touch
of a button. With simple, graphic instructions,
the PD 28 makes even the toughest measurement jobs easy.
Features
Measure up to 500 without contact
Highly accurate to 1/12 over entire
operating range
Calculation functions: addition, subtraction,
multiplication, division, squaring and square root
Expanded Pythagorean functions for measuring
indirectly
Store and identify up to 1,000 measurements
with the capability to download to your PC
Circular, slope and angle calculations
Advantages
Fast and accurate ONE PERSON operation
Measure to inaccessible places without
contact
Measure heights and lengths indirectly
Determine the angle, height and area of
triangular measurements
Calculate length and angle of
inclination of sloped distances
Set out distances from the
same start point for increased
accuracy
Measure more safely and efficiently
without the need for ladders,
scaffolding or lifts
IP 54

14F to 122F (10C to 50C)
Battery Life
Approx. 10,000 measurements with 2
type AA batteries
Dimensions (LxWxH)
6-1/2" x 2.6" x 1.8"
(165 mm x 67 mm x 47 mm)
* The maximum range depends on target
surface reflectivity and brightness of ambient
light. The PA 412 target plate should be used
if the light reflected by the target is
insufficient.
C A U T I O N
STARE INTO BEAM
620-690 nm/ 0.95 W max.
Laser beams are shown symbolically in

the illustration as red lines.
www.us.hilti.com
1.7
1.8
1.6
Range Meters
PD 22 / PD 28 Systems
PD 22 Systems
Item No.
Description
Item No.
Description
Item No.
Description
00372112
PD 22 Laser Range Meter
00378062
PD 22 Contractor Kit
00337817
PD 22 Deluxe Kit
Includes PD 22 Laser Range

Meter and Soft Pouch
00378935

Meter, PA 412 Target Plate, Soft
Pouch and Hilti Case
PD 22 Multiple Tool Package

- 3 Pack

Meter, PA 412 Target Plate, PA
421 Telescopic Sight, PA 450
Tripod Adaptor, Soft Pouch and
Hilti Case
Includes (3) PD 22 Laser Range

Meters
00378936
PD 22 Multiple Tool Package

- 6 Pack
Includes (6) PD 22 Laser Range
Meters
PD 28 Systems
Item No.
Description
Item No.
Description
Item No.
Description
0072103
PD 28 Laser Range Meter
00378066
PD 28 Data Kit
00378064
PD 28 Deluxe Kit

Meter, Soft Pouch and Hilti Case
Item No.
Description
00378065
PD 28 Pro Kit

Meter, PA 440 Data Set, Soft

Meter, PA 421 Telescopic Sight,
PA 450 Tripod Adaptor, Soft
Includes PD 28 Laser Range Meter, PA 440 Data Set, PA

421 Telescopic Sight, PA 450 Tripod Adaptor, PA 920 Short
Tripod, PA 411 Target Plate, Soft Pouch and Hilti Case
www.us.hilti.com
1.7
Range Meters
PD Accessories
Item No.
Description
00334890
PA 421 Telescopic Sight

To measure with the PD 22 / PD 28 when the laser spot is no
longer visible.
00337829
PA 450 Tripod Adapter

Precisely target long distance measurements using one
rough and one fine adjustment screw. Use alone or
with the PA 421.
For Tripods see page 1.17
00334899
PA 440 Data Set

Data cable and software for transferring stored
measurements from the PD 28 into Microsoft Excel
00334889
PA 411 Target Plate

Target plate used to increase the measuring range of the tool
(1 target = 2 pieces that fit together)
00311212
PA 970 Laser Goggles

Dramatically improves the visibility of the laser spot
00336386
PD 22 / PD 28 Soft Carrying Pouch

Soft tool case with integrated belt loop for easy carrying
www.us.hilti.com
1.8
Plumb Laser
PM 22 Plumb Laser
It's Plumb Fast!
Technical Data PM 22
Accuracy
Plumb Beam: 1/4" at 60 ft
(3 mm at 10 m)
Reference Beam: 1/8" at 5 ft
(2 mm at 1 m)
Range
Plumb Beam: 60 ft (20 m)
Reference Beam: < 3 ft (1 m)
Dust and water spray protection

IP 52 (except battery compartment) as
per IEC 529 standard
Settling time
Less than 3 seconds
Self leveling range

5 from horizontal
Power supply
4 type AA alkaline batteries or
rechargeable NiCd batteries
Laser
625645 nm, Class 2 (IEC 825-1) and
Class II as per FDA 21 CFR standard
Battery life
40 hrs with alkaline batteries or 10 hrs
with NiCd batteries at 77F (25C)

14F to 113F (10C to 45C)
Dimensions (LxWxH)
4.3" x 2" x 3.8"
(109 mm x 51 mm x 96 mm)
C A U T I O N
STARE INTO BEAM
620-690 nm/0.95 W max
One person can quickly and accurately plumb

window frames.
The PM 22 Plumb Laser shows

plumb in less than 3 seconds.
Whether transferring points from
the floor to ceiling when installing
anchors, aligning upper and lower
drywall track or vertically aligning
walls or door frames, the PM 22
provides pinpoint accuracy.
The PM 22 makes vertical alignment fast and easy.
Features
Advantages
Integrated stand allows the

PM 22 to fit directly over drywall
track up to 1-1/2"
Self leveling mechanism settles
the tool in less than 3 seconds
Out-of-level indicator lets the
user know the tool is out of level
with a flashing beam
Excellent vibration stability
Automatic shut-off, with override
ability, enables the tool to
automatically shut-off after 15
minutes to save battery life
The PM 22 allows one person to

plumb and transfer points fast
and accurately
The fast, 3 second settling time
and advanced vibration
resistance make the PM 22
ideal for jobsite use
The integrated stand fits directly
over drywall track up to 1-1/2
making alignment of upper and
lower track fast and easy
Transfer points from floor to
ceiling with the touch of a
button
- Align upper and lower drywall
track
- Mark installation points for
ductwork, sprinkler systems
or electrical fixtures
www.us.hilti.com
1.11
1.12
1.9
Multi-directional Laser
PM 24 Multi-Directional Laser
Plumb, Level and SquareSimultaneously
Technical Data PM 24
Accuracy
Plumb, level and 90: 1/4" at 60 ft
(3 mm at 10 m)
Reference beam: 1/8" at 5 ft
(2 mm at 1 m)
Range
Plumb, level and 90 beams up to and
above 100 ft (30 m) depending on
ambient lighting conditions

The integrated stand on the PM 24
makes laying out drywall track easier
than ever before.
The optional PA 240 Magnetic Bracket makes vertical alignment from any metal
surface easy.
IP 52 (except battery compartment) as

per IEC 529
Settling time
Less than 3 seconds
Self-leveling range
At the touch of a button, the new
PM 24 Multi-Directional Laser
shows plumb, level and square in
less than 3 seconds. The PM 24
enables one person to transfer points
from floors to ceilings, layout right
angles and vertically or horizontally
align columns, doors and formwork
efficiently and accurately. And with
its magnetic and air damped
pendulum system, the PM 24 resists
vibration better than ever. The
PM 24 makes all your layout work
easy, fast, and accurate.
Features
Four laser beams from the same
point of origin
Out-of level indicator lets the
user know the tool is out of level
with a flashing beam
Magnetically dampened
pendulum system self-levels the
tool in less than 3 seconds
Easy, one-button operation
Plumb reference beam enables
precise transferring of points
from floors to ceilings
Automatic shut-off, with override

ability, enables the tool to
automatically shut-off after 15
minutes to save battery life
Sturdy construction and rubber
boot make it ideal for jobsite use
Excellent vibration stability
Advantages
One person can accurately
transfer plumb, level and square
jobs that traditionally take at
least two people
Determine 90 degree angles and
parallel lines quickly and easily
for precise layout work
Horizontal leveling from any
location is made simple with the
optional PA 940 Tripod Head,
PA 240 Magnetic Bracket,
PA 250 Frame Clamp and
PA 230 Wall Mount Plate
5 from horizontal
Power supply
4 type AA alkaline batteries
or rechargeable NiCd batteries
Laser
625-645 nm, class 2 (IEC 825-1) and
Class II as per FDA 21 CFR standard
Battery life
40 hrs with alkaline batteries or 10
hrs with NiCd batteries at 77F (25C)

14F to 113F (10 to 45C)
Dimensions (LxWxH)
4.3" x 2" x 3.8"
(109 mm x 51 mm x 96 mm)
C A U T I O N
STARE INTO BEAM
625-640 nm/0.95 W max
Online Product Tour

www.us.hilti.com/pm24tour
www.us.hilti.com
1.11
1.12
1.10
Multi-Directional Laser
PM 22 / PM 24 Multi-Directional Laser Systems

PM 22 Systems
Item No.
Description
Item No.
Description
00333649
PM 22 Single Unit
00339453
PM 22 Multiple Tool Package
Includes PM 22 Plumb Laser with integrated stand,

2 PA 220 Targets and Soft Pouch
Includes (6) PM 22 Plumb Laser Single Units
PM 24 Systems
Item No.
Description
Item No.
Description
00371962
PM 24 Single Unit
00371965
PM 24 Contractor Kit
Includes PM 24 Multi-Directional Laser, PA 271 Metal Stand,

Soft Pouch, 2 PA 211Target Plates, 4 batteries, operating
instructions
00373254
Includes Hilti case, PM 24 Multi-Directional Laser, PA 271

Metal Stand, Soft Pouch, 2 PA 211 Target Plates, 1 PA 240
Magnetic Bracket, 1 PA 250 Frame Clamp, 1 PA 230 Wall
Mount Bracket, 4 batteries, operating instructions
PM 24 Multiple Tool Package - 3 Pack

Includes (3) PM 24 Multi-Directional Laser Single Units
00373253
PM 24 Multiple Tool Package - 6 Pack

Includes (6) PM 24 Multi-Directional Laser Single Units
Item No.
Description
00375053
00376013
PR 16 Interior Deluxe Kit

PR 16-IF Interior Deluxe Kit
PR 16 Rotating Laser, PA 320 Wall Mount Bracket, PM 24 Multi-Directional Laser Single Unit
www.us.hilti.com
1.11
Multi-Directional Laser
PM Accessories
PM 22 Accessories
Item No.
Description
00333641
PA 220 Target For PM 22 (pkg of 3)

Target used to align objects when using the PM 22
PM 22 / PM 24 Accessories
Item No.
Description
00369271
PA 271 Stand
Replacement stand for the PM 22 or PM 24
PM 24 Accessories
Item No.
Description
00310727
PA 240 Magnetic Bracket

For mounting the PM 24 to steel surfaces
00310729
PA 230 Wall Mount Plate

A steel bracket for use with the PA 240 Magnetic Bracket for
mounting the PM 24 to non-steel surfaces
00310728
PA 250 Frame Clamp

For use with the PA 240 Magnetic Bracket for mounting the
PM 24 to small columns, beams, door openings, etc
00310990
PA 940 1/4" Tripod Head

Tripod adapter for mounting the PM 24 to a standard 5/8"
tripod
00371397
PA 211 Target For PM 24 (pkg of 3)

Target used to align objects with the PM 24
www.us.hilti.com
1.12
Rotating Lasers
Hilti PR 16 & PR 16-IF Rotating Lasers

Versatile. Fast. Accurate.
Technical Data PR 16 & PR 16-IF

Accuracy
3/32" at 60 ft (1 mm at 10 m)
Range (diameter)
200 ft (60m) with PA 341 Scanning
Beam Catcher
PR 16: 1000 ft (300 m)
with the PA 350 Laser Receiver
PR 16-IF: 1300 ft. (400m)
with PA 350 Laser Receiver
Alignment at right angles for drywall installations
Protection class
IP 42M as per IEC 524 std
Self-leveling range
Vertical alignment of J Hooks to hang
electrical wiring (shown with the DXA
Pole Tool Adaptor)
Fully automatic 5
Power supply
4 type D alkaline batteries or optional
rechargeable NiCd battery set
Rotation speeds
Stop mode
Manual mode
Scanning beam catcher mode
Laser receiver mode
0
50 rpm
80 rpm
300 rpm
Laser class
PR 16: 635 nm, 0.95 mW, class 2
(IEC 825-1) & Class II as per FDA21
CFR 1040 std
PR 16-IF: 635 nm, up to 4.7 mW,
class 3a (IEC 825-1) & Class IIIa as
per FDA21 CFR 1040 std
Battery life
Over 80 hours with alkaline batteries

4F to 122F (20C to 50C)
5.5 lb (2.3 kg) without batteries
Dimensions (LxWxH)
7.2" x 6.6" x 9.2"
(183 mm x 168 mm x 234 mm)
C

STARE INTO BEAM
635 nm/0.95 mW
PR 16-IF
The fully-automatic Hilti PR16 Rotating Laser comes into its own in
indoor applications. With its Magic Chalkline scanning feature, the
PR 16 projects a clearly visible line allowing the user to work hands
free easily and accurately. The line can even be extended to cover
large working areas. With the PR 16 and PR 16-IF rotating lasers,
horizontal and vertical alignment, setting inclinations and
laying out 90 degree angles and parallel lines can be
carried out by a single person faster and easier than ever
before.
The Magic Chalkline

The innovative PA 341 Scanning Beam
Catcher stops the laser beam and
projects a clear line that can be
extended to make working in large
areas faster and easier than ever before.
Features
Weight
PR 16
Horizontal alignment of suspended ceilings

STARE INTO BEAM
635 nm/4.7 mW
CLASS IIIa LASER PRODUCT
Online Product Tour

www.us.hilti.com/pr16tour
www.us.hilti.com
1.15
Fully self-leveling within 5 degrees

Automatic out-of-level cut off
Servo buttons for beam
adjustment
Use with the PA 341 Scanning
Beam Catcher or the PA 350
Laser Receiver
Dual slope capability
Rechargeable battery pack
Advantages:
One person can quickly and
easily align horizontal, vertical
and inclined planes or set out
and transfer right angles
Four rotation speeds allow
optimal beam visibility
The magic chalkline allows
the user to work hands
free
Self-explanatory control panel
makes the PR 16 easy to
operate
1.16
1.13
Rotating Lasers
PR 60 Rotating Laser
Fast. Simple. Reliable
PR 60s liquid
compensator
provides
increased
accuracy and
excellenct
vibration
resistance for
reliable jobsite
use.
Technical Data PR 60
Accuracy
1/16" at 60 ft
( 0.7 mm at 10 m)
Range (diameter)
1300 ft (400 m) with PA 350 Laser
Receiver
Easy, twobutton
operation
makes the
PR60 the best
choice for all
outdoor
leveling
projects
The intelligent PA 350 Laser Receiver notifies

the user when the tool in knocked out of level
The PR 60 horizontal rotating laser is specially designed

for your toughest outdoor leveling applications. The
rugged tool is dust and water protected and is equipped
with an outstanding vibration absorption system making
it ideal for excavating foundations or drainage pipes,
aligning ceiling and foundation formwork and the
precise leveling of concrete pours. The tool levels itself
automatically, so there's no need for manual leveling in
advance, and includes a shock indicator warning that
lets the user know if the tool has been knocked off
level. The innovative PR 60 makes leveling projects
involving concrete slabs, foundations, basements and
drainage systems a one-person job.
Advantages:
Horizontal aligning jobs that previously required
several people can be carried out faster and easier
by only one person
Rugged, dust and water protected housing make the
PR 60 ideal for demanding outdoor applications
Simple, two button control panel makes the PR 60
the best choice for everyone on the jobsite
Unique liquid compensator offers excellent vibration
control for reliable jobsite use

IP 56 as per IEC 529 standard
Self leveling range

5 from horizontal
Power supply
4 type D alkaline batteries or optional
rechargeable NiCd battery set
Laser
795 nm, class I (EN60825-1) and
Class I as per FDA 21 CFR standard
Battery life
Over 140 hrs with alkaline batteries or
60 hrs with the rechargeable battery
pack at 68F (20C)

4F to 122F (20C to 50C)
Dimensions (LxWxH)
10.2" x 5.9" x 9.5"
(260 mm x 151mm x 242 mm)
C A U T I O N
STARE INTO BEAM
795 nm/0.95 W max
CLASS I LASER PRODUCT
Features
Simple two-button control panel
makes the PR 60 easy to use
Fully self-leveling no manual
screws to adjust
Liquid compensator offers
excellent vibration
resistance
Automatic cut-off so the
tool wont operate if
knocked out of level
cut-off override function
allows the tool to relevel
itself when activated
PA 350 Laser Receiver
alerts the user with an
acoustic signal if the
tool is knocked off level
Over 140 hours of
operation with new
alkaline batteries
Rechargeable battery
pack (optional)
www.us.hilti.com
1.15
1.16
1.14
Rotating Lasers
PR 16 / PR 16-IF / PR 60 Systems
PR 16 / PR 16-IF Systems
Item No.
Description
Item No.
Description
Item No.
Description
00371897
00371898
PR 16 Rotating Laser (Class 2)

PR 16-IF Rotating Laser (Class 3a)
00375051
00376014
PR 16 Interior Standard Kit

PR 16-IF Interior Standard Kit
00376760
00376763
PR 16 Contractor Kit
PR 16-IF Contractor Kit
Includes PR16 Rotating Laser,

PA 341 Scanning Beam Catcher,
PA 321 Wall Mount Bracket and
Includes PR 16 Rotating Laser,

PA 341 Scanning Beam Catcher,
cleaning cloth, 4 type D
batteries and Hilti case
Item No.
Description
00375055
PR16 Facade Mount Kit

PA 341 Scanning Beam
Catcher, PA 350 Laser Receiver,
PA 911 Tripod, and choice of
leveling staff
PR16 Rotating Laser,

PA 372 Facade Adapter and
Item No.
Description
00375054
PR16 Jobsite Kit
Item No.
Description
Item No.
00375053
00376013
PR 16 Interior Deluxe Kit

PR 16-IF Interior Deluxe Kit
00376761
00376762
PR 16 Rotating Laser, PA 321

Wall Mount Bracket, PM 24
Multi-directional Laser Single
Unit , PA 341 Scanning Beam
Catcher
PR16 Rotating Laser, PA 370

Batter Board Adapter and
Item No.
00376012
Description
PR 16 Interior Professional Kit

PR 16-IF Interior Professional Kit
PA 932 Tripod, PA 350 Laser
Receiver and choice of leveling
staff
Description
PR 16-IF Interior Kit

Includes PR 16-IF Rotating Laser,
PA 321 Wall Mount Bracket and
2 PA 341 Scanning Beam Catchers
PR 60 Systems
Item No.
Description
Item No.
Description
Item No.
Description
00337055
PR60 Rotating Laser
00376016
PR60 Contractor Kit
00376017
PR60 Deluxe Kit

PA 350 Laser Receiver, PA 360
Receiver Holder, 4 D batteries
and Hilti Case

PA 911 Tripod and choice of
leveling staff

PA 910 Tripod, Rechargeable
Battery Pack and choice of
leveling staff
www.us.hilti.com
1.15
Rotating Lasers
PR 16 / PR 16-IF / PR 60 Accessories
PR 16 Accessories
Item No.
Description
00335526
PA 372 Facade Adaptor

Mount the PR 15 to a building to align the facade. Also allows use
of PR 16 vertically on a tripod
00333834
PA 370 Batter Board Adaptor

For aligning building foundations
00371901
PA 341 Beam Catcher

PA 341 Scanning Beam Catcher makes the laser automatically
sweep forward and back on the target resulting in excellent
visibility
00268247
DXA Beam Catcher Holder

Attaches the PA 341Scanning Beam Catcher to a Hilti Powder
Actuated tool. Ideal for overhead applications.
00377447
PR 16 Rechargeable Battery Pack

Includes NiCd batteries and 120V AC/DC adapter
00311038
PA 320 Wall Mount Bracket

For attaching the PR 16 to a wall. Scale in inches.
Perfect for leveling suspended ceilings!
PR 60 Accessories
Item No.
Description
00336954
PR 60 Rechargeable Battery Pack

Includes NiCd batteries and 120V AC/DC adapter
PR 16, PR 16-IF and PR 60 Accessories

Item No.
Description
00311393

Electronically detects the laser beam
Range with PR 16: 1000 ft diameter
Range with PR16-IF: 1300 ft diameter
Range with PR 60: 1300 ft diameter
00311778
PA 360 Receiver Holder

For attaching the PA 350 Laser Receiver to a leveling staff (not
needed with the PA 960 Leveling Staff)
www.us.hilti.com
1.16
Tripods
Laser System Tripods

Item No.
Description
00372893
PA 911 Heavy Duty Tripod

For use with PR 60 Rotating Laser
NEW!
Height adjustable from 3'3" to 5' (1 m to 1.65 m) with 5/8" thread

Heavy-duty design capable of withstanding tough jobsite
conditions
Spiked feet for steady, outdoor applications
The PA 911 is the type of tripod most frequently encountered
on construction sites and in use by surveyors
00310982
PA 920 Short Tripod with Height Adjustment

For use with PM 24, PD 22, PD 28
Ideal tripod for vertical distances ranging from 2'3" to 4'9" (0.69
m to 1.45 m) with 5/8" thread
Built-in bubble level for quick, easy set-up
The PA 920 is the type of tripod most frequently encountered
in interior finishing
Ideal for use in low to medium height range
00315999
PA 932 Large Tripod with Height Adjustment

For use with PR 16 and PR 16-IF Rotating Lasers
Ideal tripod for vertical distances ranging from 2'10" to 9'5"
(0.78 m to 2.88 m)
Integrated measuring scale allows accruate tool positioning
A measurement scale on the column tells the exact height of
the tool
Extended height capability make the PA 932 excellent for
suspended ceiling applications
Built-in bubble level for quick, easy set-up
The PA 932 has braced tripod legs for added stability
Rubber shoes at the base of the tripod leg can be adjusted
down for steady set-up on slippery surfaces
www.us.hilti.com
1.17
Leveling Staffs
Leveling Staffs
Item No.
Description
00310988
PA 960 Leveling Staff

Fractional / Metric staff with a maximum height of 7'11" (2.4 m)
High-grade anodized aluminum
fractional/metric
Built-in holder mounting the PA 341 Beam Catcher or PA 350

Laser Receiver directly to the staff
Offsets can be easily calculated by extending or retractiin the
lower section of the staff from the zero reference mark
Built-in bubble level
00338652

Fractional staff with a maximum height of 16' (4.88 m)
High-grade fiberglass reinforced plastic, electrically
non-conductive, suitable for outdoor applications
fractional
Screw mounting point for attaching the PA 350 Laser

Receiver directly to the rod for measuring different heights
Adjustable / removable bubble level
00339671

Feet / Tenths staff with a maximum height of 16' (4.88 m)
feet/tenths
Screw mounting point for attaching the PA 350 Laser receiver

directly to the rod for measuring different heights
00338129

Metric staff with a maximum height of 16' (4.88 m)
metric
Screw mounting point for attaching the PA 350 Laser receiver

directly to the rod for measuring different heights
www.us.hilti.com
1.18
Multi-Detector
PS 20 Multi-Detector
Dont Chance It.
Technical Data
For reinforcement detection:
Maximum detection depth
4" (100mm)
Maximum depth reading

3-5/32" (80mm)
Depth detection accuracy

All figures based on 1/2" (12mm) round
reinforcing bars
Depth Range
Accuracy
13/32" to 1-5/32"
(10-30mm)
1-5/32" to 2-11/32"
(30-60mm)
2-11/32" to 3-5/32"
(60-80mm)
3/32"
(2mm)
7/32" to 5/16"
(5-8mm)
7/16" to 1/2"
(11-13mm)
Determine the position of rebar before

you drill
The center hole lets you mark the

precise position of the rebar or conduit
Place anchors with confidence using

the PS 20s minimum depth function
Features
Advantages
Determine the position of

reinforcement in concrete
up to 4" deep
Determine the depth of
reinforcement up to 3-5/32"
deep for all reinforcement from
#3 - #11 (8-36 mm)
Determine the position of copper
or aluminum pipes up to
2-3/8" deep
Minimum Coverage Function
detects rebar to predefined depth
Integrated center hole
allows accurate marking of
detected objects
Check the location of rebar and

copper or aluminum pipes before
drilling
-Avoid costly and dangerous
drilling mistakes
-No more time lost from
hitting rebar
-Longer drill bit life
Check the concrete coverage
over reinforcement
Identify the presence of live,
unshielded, electrical cables
Easily distinguish between closely
spaced reinforcement
Minimum separation for

detection
1.7" (42mm) between bars or a ratio
of depth/separation of 1:1.2
Rebar diameter
#3 - #11 (8-36mm)
Non-Ferrous metal detection

maximum detection depth
2-3/8" (60mm)
Power supply
4 AA alkaline batteries or rechargeable
NiCd batteries
Battery life
40 hours at 73 F (23 C) with alkaline
batteries

with alkaline betteries
14F to 122F (-10C to 50C)
Dimensions (LxWxH)
11" x 3.7" x 3.4" (280 x 95 x 86 mm)
Accidently drilling into rebar is a

recurring problem for construction
professionals. The Hilti PS 20
Multi-Detector helps solve that
problem. Not only can this
extraordinary tool detect rebar in
concrete up to 4" deep, it also
detects copper and aluminum pipes
and post-tension cables. Just
switch the tool on, calibrate and
scan. Its that easy.
www.us.hilti.com
1.20
1.19
Multi-Detector
PS 20 System & Accessories

Item No.
Description
00340803
PS20 Multi-Detector
Includes PS 20, 2 Markers, 1 Replacement Glider Set, Soft
Carrying Pouch, Hilti Case and 4 type AA batteries
00340807
PS 20 Glider Set
Includes one replacement sensor head cover and one battery
compartment cover
00340806
PS 20 Marker (Pkg of 12)

China markers for marking the location of detected objects
00340805
PS 20 Soft Carrying Pouch

Soft tool case with integrated belt loop for easy carrying
Drill with Confidence and Safety.

No-risk drilling
With the Hilti PS 20 you
know where to drill.
Reduce time lost from
hitting rebar
Help eliminate bills for
repairs to copper water
pipes or damaged
electric cables
The risk of being
shocked from live
electric cables is
dramatically reduced.
Place anchors
with confidence
The Hilti PS 20 indicates
the depth you can expect
to encounter rebar in the
concrete.
Accurate
coverage depth
measurement
For quality assurance,
damage analysis or
evaluating the current
situation before
renovation, the PS 20 is
one of the most
economical and easiest
ways of obtaining
accurate, reliable
coverage information.
www.us.hilti.com
1.20
Detection System
FS 10 Ferroscan
Detection Made Simple.
Technical Data
Accuracy
Depth of Coverage: 10% typical
when the ratio of spacing:depth of
coverage = 2:1
Greater accuracy is possible if known
diameter is entered in the tool
Diameter: 1 size in accordance with
DIN 488, ACI 318-106, CPCI, JIS G
3112 when the ratio of spacing:depth
of coverage = 2:1
Range
Imagescan: See chart below
Quickscan: 4" (100 mm)
Imagescan function produces a precise

picture of the rebars location
The specially designed Ferroscan PC software allows further processing and
evaluation of all the data recorded on the Ferroscan.
Memory capacity
42 Imagescans and/or Quickscans
Software compatibility
Most Windows compatible word
processing software; ie. Microsoft
Word, Word for Windows, Excel, etc.
Diameter measurement accuracy

1 dia size in accordance with
DIN 488, ACI 318-106, CPCI,
JIS G 3112 when ratio of spacing to
depth of coverage is greater than 2:1
Memory capacity
42 Imagescans and/or Quickscans
Scanning speed
up to 1.64 ft/s (0.5 m/s)
Battery life per charge

4 hours of constant use
Protection class
IP 54
Detecting reinforcement,
determining depth and calculating
diameter has never been easier.
The Hilti FS10 Ferroscan Detection
System provides a quick overview
of the reinforcing bars in concrete
structures. The data can be
evaluated on site using the monitor
unit or exported to a PC for more
in-depth analysis and reporting.
When knowing the rebar
configuration in concrete is critical,
the Hilti FS10 Ferroscan is the only
tool of its kind.
Features
Applications
Produce an image of the rebar

in the concrete down to 7.1
inches*
Determine depth of coverage up
to 5.9 inches*
Identify diameter of rebar up to
2.4 inches deep
42 Scan memory for later
analysis
Quickscan function detects
individual reinforcing bars in
scans up to 98 feet
FS10 software and computer
connection cable included
Identify the reinforcement

pattern in concrete for
renovation of buildings when
plans are not at hand,
acceptance inspections of precast concrete components and
avoiding cutting of structurally
relevant rebar
Determine the amount of
concrete coverage for building
inspections, renovation and
quality control
Structural analysis, locating the
position, pattern and coverage
of rebar
Up to 42 scans can be stored in
the Ferroscan for later analysis
on a computer
Quickscan function allows quick
detection of individual
reinforcing bars in scans up to
98 feet long
Determine the mean depth of
coverage and standard deviation
of reinforcements with the
Ferroscan PC software
*see product specifications for exact depth

performance
14F to 122F (10C to 50C)
Weight
RV10 Monitor: 4.8 lb (2.2 kg),
RS10 Scanner: 2.2 lb (1 kg)
Dimensions (LxWxH)
RV10 Monitor: 11" x 8" x 3"
(275 mm x 200 mm x
80 mm)
RS10 Scanner: 8.5" x 5.5" x 5.5"
(230 mm x 140 mm x
140 mm)
www.us.hilti.com
1.22
1.22
1.21
Measurement range (inches)

Standard diameter as per
ACI standard 318-106 (inches)
Max depth (in.) for image processing
Max depth (in.) for determining depth of coverage
Max depth (in.) for determining diameter
Measurement range (mm)
Standard diameter as per Canadian CPCI (mm)
Max depth (mm) for image processing
Max depth (mm) for determining depth of coverage
Max depth (mm) for determining diameter
#3
3/8
5.5
3.8
2.4
#10
150
100
60
#4
4/8
5.9
4.1
2.4
#5
5/8
6.3
4.3
2.4
#15
160
110
60
#6
6/8
6.3
4.3
2.4
#20
160
110
60
#7
7/8
6.3
4.3
2.4
#8
1
6.3
4.3
2.4
#25
160
110
60
#9
1.13
6.5
4.8
2.4
#30
170
130
60
#10
1.27
6.8
5.3
2.4
#11
1.41
7.1
5.9
2.4
#36
180
150
60
Detection System
FS 10 Ferroscan System & Accessories

Item No.
Description
00235829
FS 10 Ferroscan System Fractional

Complete with RV10 Monitor, RS10 Scanner, RB10 Battery,
Charger TCU 12H/115V, Paper Reference Grids (pkg of 10),
Hilti Case and FS 10 Ferroscan software
00241250
FS 10 Ferroscan System Metric

Complete with RV10 Monitor, RS10 Scanner, RB10 Battery,
Charger TCU 12H/115V, Paper Reference Grids (pkg of 10),
Hilti Case and FS 10 Ferroscan software
00235899
RB10 Battery
Spare battery: 10 NiCd cells, capacity > 1.4 Ah
00241248
RC 10 Ferroscan Cable 5' (1.5 m)

5' (1.5 m) replacement cable for connecting the scanner to
the monitor
00241249
RC 10 Ferroscan Cable 32' (10 m)

Extra-long connecting cable 32' (10 m): for easy scanning
over long distances
00218105
Charger TCU12H/115V
RG10 battery charger
00235890
RG 11 Fractional Paper Grids

Spare paper grids in inch increments (in packs of 10)
00235891
RG 10 Metric Paper Grids

Spare paper grids in mm increments (in packs of 10)
The three typical areas of application
Verification of reinforcement
Checking coverage
Avoiding rebar hits
Task
Change of use of buildings when plans are

not at hand
Acceptance inspections of concrete
components
Checking reinforcement before structural
repair
Post installed reinforcement
Building acceptance inspections

Coverage checking over a large area during
renovation
Quality control
Hammer drilling without the costly problem

of drilling into rebars
No cutting through statically relevant
reinforcing bars
Achieve considerably longer drill bit life
What
information is
required?
Position of reinforcing bars

Depth of coverage
Bar diameter
Depth of coverage
Position of the reinforcing bars
Types of scan
Imagescan
Quickscan for checking
Quickscan
Imagescan in difficult situations
Quickscan
Imagescan where through holes are drilled
Typical objects
Industrial buildings, floors and decks, beams,

supporting columns, etc.
Bridges, tunnels, underground car parks,

etc.
Repetitive fastening applications, ventilation

ducts, through holes, etc.
www.us.hilti.com
1.22
NEW
Hilti TE-SP Polygon Chisels
Innovation
Self-Sharpening
Chisels
See page 2.49

1/2" Drill
SR 16
Page 2.7
Multi-Purpose Hammer Drill

TM 7SIII VSR
Page 2.8
Rotary Hammer Drills

TE 2
TE 2-S
TE 2-M
TE 5 A
TE 6-S
TE 6-C
TE 6-A
TE 15
TE 15-C
TE 18-M
TE 25
TE 25S
Page 2.10
Page 2.11
Page 2.12
Page 2.13
Page 2.15
Page 2.16
Page 2.17+
Page 2.19
Page 2.20
Page 2.21
Page 2.22
Page 2.23
Medium Mass Combihammer

TE 35
Page 2.31
Heavy Duty Combihammer

Just in
the TE 56xi
See Page s.
for detail
TE 55
TE 76-ATC & TE 76
Page 2.35
Page 2.36+
Breakers & Demolition Tools

TE 104
TE 505
TE 705
TE 805
TE 905
Page 2.42
Page 2.44
Page 2.45
Page 2.47
Page 2.48

Connection End
System
Application
Drilling Range
Page
Drilling into steel, softwood, particle

board and hardwood.
2.7
TM 7SIII VSR
For a wide variety of applications
2.8
Multi-purpose Hammer Drill
1/2" Drill
SR 16
3/16"
CONCRETE
3/16"
5/16"
TE 2
TE 2-S
TE 2-M
TE 2 drilling anchor holes in

concrete and masonry
TE 2-S precision drilling for
3/16"
CONCRETE
3/4"
anchor holes in concrete, masonry
and brittle materials
TE 2-M multifunctional tool for
3/16"
5/16"
concrete, masonry, brittle material,
wood and metal
2.10+
TE 5 A
Rotary hammer drilling into concrete

with cordless convenience
2.13
TE-C (SDS)
3/16"
CONCRETE
3/16"
* Excludes
consumable
battery pack
TE 6-S
5/8"
3/8"
Hole Saw: up to 5"

Steel: Up to 1/2"
Drilling anchor holes and through

holes in concrete and masonry as well
as drilling into wood and steel
3/16"
2.15
CONCRETE
5/16"
TE 6-C

holes in concrete and masonry as well
as drilling into wood and steel, and
3/16"
light corrective chiseling on masonry
and concrete
Cordless rotary hammer drilling into

concrete. Mobility with unmatched
power reserves.
1"
9/16"
2.16
CONCRETE
5/16"
TE 6-A
5/8"
1"
9/16"
2.17
3/16"
5/16"
CONCRETE
1"
9/16"
* Excludes
consumable
battery pack
2.3

Connection End
System
TE 15
Application
Drilling Range
Page
2.19
3/16"
TE-C (SDS)
CONCRETE
1"
3/8"
5/8"
Wood: up to 1-1/4"
Steel: Up to 1/2"
TE 15 C
Mini-combihammer provides reliability

and versatility for rotary hammer
drilling and light duty chiseling into
concrete
2.20
3/16"
CONCRETE
1"
3/8"
5/8"
Wood: up to 1-1/4"
Steel: Up to 1/2"
TE 18-M
2.21
3/16"
CONCRETE
1"
3/8"
5/8"
Steel: Up to 1/2"
TE 25
Rotary hammer drilling into concrete,

improved comfort and lighter weight
makes the powerful TE 25 the ideal
hammer drill for medium to
heavy-duty anchoring
2.22
3/16"
CONCRETE
3-1/2"
1/2"
3/4"
Hole Saw: up to 5"
Steel: Up to 1/2"
2.23
TE 25S
3/16"
CONCRETE
3-1/2"
1/2"
3/4"
Hole Saw: up to 5"

Steel: Up to 1/2"
TE 35
TE-T
(SDS TOP)
2.31
3/8"
CONCRETE
3-9/16"
1/2"
1"
Hole Saw: up to 5"
Steel: Up to 1/2"
TE 55
For chipping, anchor hole drilling and

through hole drilling in concrete and
masonry
For drilling into and breaking

concrete.
Just in
the TE 56xi
See Page s.
for detail
TE-Y
(SDS Max)
2.35
1/2"
CONCRETE
3-9/16"
5/8"
1"
Steel: Up to 1/2"
TE 76-ATC & TE 76
2.36
The mega power combihammer for

drilling into and breaking concrete.
1/2"
CONCRETE
7/8"
6"
1-3/8"
Wood: Up to 5" Hole Saw

Wood: Up to 1-1/4" Auger
Steel: Up to 1/2"
2.4

Connection End
System
Application
Chisels
TE 104
Lightest chipping hammer for

concrete, masonry, and stone
breaking, chiseling, etc.
Pointed
Flat
Channel
Mortar
Wide Flat
Flex
2.42
TE 505
A lightweight breaker for concrete,

masonry, and stone breaking,
chiseling, etc.
Pointed
Flat
Spoon
Channel
Wide Flat
Mortar
Ground Rod Adapters
1/2" to 3/4"
2.44
TE 705
Light-duty breakers with more power,

less vibration, TE-Y connection end for
Pointed
Flat
Spoon
Channel
Wide Flat
Mortar
Ground Rod Adapters
1/2" to 3/4"
2.45
TE 805
For concrete, masonry, and stone

Pointed
Flat
Wide Flat
Ground Rod Adapters
5/8" to 7/8"
2.47
TE 905
Active vibration reduction system

maximizes operator comfort. For
breaking, chiseling, ground rod driving
etc.
Pointed
Flat
Wide Flat
Ground Rod Adapters
5/8" to 7/8"
2.48
TE-C (SDS)
Breakers and Demolition Tools
TE-Y
(SDS Max)
TE-S
Page
What Makes Hilti Hammer Drills Drill Faster?

When comparing rotary hammers
and combihammers, four things must
be taken into consideration: single
impact energy, impact frequency, the
shape of the impact pulse and the
rotation angle between the impacts. All
four have to be considered before
stating one tool is faster, better or
stronger than another. It is important to
understand the four criteria of optimum
drilling performance and how they work
together.
Single impact energy measures
how hard the tool hits. It is important to
note that tool manufacturers do not all
measure single impact
energy in the same way.
For example, Hilti
measures the energy
transferred from the
point of the shortest
chisel to the work surface
while our biggest competitor measures
the energy transferred from the striker
piston to the the impact point on the
2.5
connection end. This means that our

competitors testing method will result
in a higher measure of single impact
energy.
Impact Frequency
Impact frequency
measures
the
number of times
the insert tool
strikes the base
material in one
minute
(blows per minute).
Shape of Impact Pulse
The impact pulse delivered by a
hammer drill or concrete breaker can
be determined by the tool
manufacturer. The
impact pulse of
Shape of the
impact pulse
Hilti hammer
Good for chiseling
high vibration
Force
Good for drilling

low vibration
Time
drills is optimized so that the carbide

head of the bit stays in contact with the
concrete just long enough to ensure
proper dust removal. This is illustrated
by the flatter curve in the impact pulse
diagram. Fast dust removal is the key
determinant of drilling speed.
Furthermore, lower vibration allows
greater operator comfort and less
uncontrolled fracturing of concrete
during the drilling process.
The higher arcing curve on the
impact pulse diagram illustrates an
impact pulse designed for good
chiseling performance. The energy for
each example in our diagram is equal.
The difference between them is the
shape of the energy curve
because the force has been
applied differently over time.
Rotation Angle
Between Impacts
The rotation angle
between impacts is the location
where the carbide head of the drill bit
strikes the concrete as it is drilling the

hole. The rotation angle is determined
by the impact frequency (BPMs) and
speed (rpm). This part of the optimum
drilling formula is where Hilti also
provides better value to their
customers. Hilti is the only power tool
manufacturer in the industry that
optimizes its concrete drilling systems
by ensuring that the drill bit design
works with the tools in which they are
used. Hilti hammer drills are designed
to turn the carbide head of Hilti drill bits
between each impact on the concrete
so that it does not strike in the same
place during each revolution. This
optimizes the breakage of the concrete
under the carbide of the drill bit.
If the carbide rotation angle is
not optimal, the carbide will
strike the concrete in the
same locations repeatedly.
This would lead to slower
removal rates and shorter
drill bit life.

Insert tools and accessories not shown to scale.
TE-Y
TE-S
page
page
page
page
Drill Bits
Carbide Tipped Drill Bits
2.25
2.33
2.38
Masonry/Cruciform Bits
2.27
2.34
2.39
Carbide Tipped Single Piece Core Bits
2.34
2.39
Thin Wall Core Bits
2.27
Pointed Chisels
2.29
2.34
2.40
2.49
Flat Chisels
2.29
2.34
2.40
2.49
Scaling & Offset Chisels (Wide Flat)
2.29
2.34
2.40
2.49
Channel Chisels
2.29
2.34
2.40
Clay Spade
2.46
2.49
Flex Chisels
2.29
2.40
2.49
Mortar/Joint Chisels
2.29
2.34
2.40
Ballast Chisel
2.49
Bushing Tool
2.34
2.46
2.49
2.43
2.49
2.24
2.24
2.34
Ground Rod Adapters
2.46
2.49
Spline Shank to SDS+
2.24
TE-Y to TE-C
2.41
2.41
2.41
Specialized
Chisels
TE-T
Core Bits
22
TE-C
Needle Adapter
Adapters
Chucks
Tamping Tool
Chucks
Rebar Adapters
2.6
1/2" Drill
Hilti SR 16 High-Torque 1/2" Drill

A Powerful 2-Speed 1/2" Drill Designed To Last
Technical Data
Voltage
110120 V
Nominal Power
600 W
Nominal Current
5.8 A at 100 V
No-Load Speed
1st speed: 0750 rpm
2nd speed: 01900 rpm
Max. Torque
1st speed: 442 in.-lb
2nd speed: 177 in.-lb
Weight
4.0 lb
Chuck
Keyless chuck with hard metal jaws:
1/16" to 1/2" diameter
R e p a i r
Advantages
Accessory Program
High torque motor

Hilti quality for greater reliability
2 speeds
Electronically controlled variable speed switch
Reversing lock out
Keyless chuck
For drilling into steel, softwood, particle board and hardwood
Steel twist bits to 1/2" diameter

1/2" keyed chuck
Belt hook
Impact resistant plastic Hilti
Case
Hole saw up to 3-1/2" diameter
P r o g r a m
Item No.
Description
00255948
SR 16 in cardboard box
Complete with side handle and 13 ft (4 m) supply cord,
operating instructions and safety precautions
00311165
SR 16 with keyed 1/2" chuck in cardboard box

Complete with side handle and 13 ft (4 m) supply cord,
operating instructions and safety precautions
Accessory Program
Item No.
Description
00257395
00240719
00240704
Plastic Hilti case (not shown)

Belt Hook (not shown)
1/2" Keyed Chuck
www.us.hilti.com
Steel Jobber Bits
see page:
4.6
2.7
Hilti TM 7SIII Multi-Purpose Hammer Drill

Versatile For A Wide Variety Of Applications
Technical Data
Power Input
650 W
Voltage
115 V AC
Frequency
50/60 Hz
No Load Speeds
Low: 01000 rpm
High: 03000 rpm
Percussion
Low: 20,000 blows/min
High: 57,000 blows/min
Dimensions (LxWxH)
Advantages
Accessory Program
Smooth shank carbide-tipped

masonry bits from 3/16" to 5/8"
KWIK-CON II+ driver for 3/16"
and 1/4" masonry screws
Angle attachment for right
angle drilling
1/2" to 11/16" BT style
diamond core bits
5/8"11 adapter for BI
diamond core bits
Water swivel for diamond bits
SM or BT 1/2" to 1-1/2"
Two drilling modes: rotary hammer and rotary only

Two speed ranges with variable speed control
Reversing switch for quick fastener removal
Gooseneck depth gauge and side handle for
operator convenience
Right angle drilling attachment available for work in tight places
Water swivel accessory for core drilling
Continuous-run button
UL listed, double-insulated construction
13" x 2-3/4" x 7"
Weight
6.5 lb
Drilling Rate
Up to 7" per min in 4,000 psi concrete
with a 5/16" diameter bit
3/16"
CONCRETE
3/16"
5/8"
5/16"
Item No.
Description
00095948
TM 7SIII VSR Deluxe (shown)

Includes dust shield, depth gauge, selector chart, impact
resistant Hilti case, instruction manual, chuck key, side handle,
parts list
Accessories
Item No.
Description
00235097
KWIK-CON II+Driver for 3/16" & 1/4"masonry screws
00090411
Replacement Chuck 1/2" with key
00050835
Water Swivel for diamond bits
SM, DD-BT 1/2" to 1-1/2" when encountering rebar
00052153
Angle Attachment for right angle drilling
00075283
Chuck Key
not shown
www.us.hilti.com
2.9
2.8
Carbide Tipped Smooth Shank TM Masonry Drill Bits

Fit Directly Into Jacobs Style Chuck
TM Bits
Effective
Item No.
Description
Diameter
Length
Drilling Depth
00061465
00061466
00061469
00061470
00061467
00061473
00061474
00061477
00061468
00061471
00061483
00061472
00061485
00062898
00220608
TM Bits - Metric
Bit TM 3/16-4
Bit TM 3/16-6
Bit TM 1/4-4
Bit TM 1/4-6
Bit TM 1/4-18
Bit TM 5/16-4
Bit TM 5/16-6
Bit TM 3/8-6
Bit TM 3/8-18
Bit TM 3/8-24
Bit TM 1/2-6
Bit TM 1/2-18
Bit TM 9/16-6
Bit TM 5/8-8
Bit TM 5/8-18
3/16"
3/16"
1/4"
1/4"
1/4"
5/16"
5/16"
3/8"
3/8"
3/8"
1/2"
1/2"
9/16"
5/8"
5/8"
4"
6"
4"
6"
18"
4"
6"
6"
18"
24"
6"
18"
6"
8"
18"
2-1/8"
3"
2-1/8"
3"
16"
2-1/8"
3"
3"
16"
21-1/2"
3"
16"
3"
5-1/2"
15-1/2"
Item No.
Description
Diameter
Length
Drilling Depth
00335841
00335842
00335843
00335844
00335845
00335846
00335847
00335848
00335849
00335850
Bit TM 4/8.5 Metric

Bit TM 5/8.5 Metric
Bit TM 5/15 Metric
Bit TM 6/10 Metric
Bit TM 6/15 Metric
Bit TM 8/15 Metric
Bit TM 8/20 Metric
Bit TM 10/20 Metric
Bit TM 12/15 Metric
Bit TM 14/20 Metric
4 mm
5 mm
5 mm
6 mm
6 mm
8 mm
8 mm
10 mm
12 mm
14 mm
3-5/16"
3-5/16"
6"
4"
6"
6"
7-7/8"
7-7/8"
6"
7-7/8"
1-1/2"
1-1/2"
4"
2"
4"
4"
5"
5"
4"
5"
Effective
TM Bit Packages
Effective
Pkg
Item No.
Description
Diameter
Length
Drilling Depth
Qty
00000409
00000410
00000411
00000412
00000414
00023848
00023849
00000415
00023850
00028859
00028860
00028861
00028862
00028863
00028864
00028865
00028866
00028867
00028868
00028870
TM 3/16-4 Bit Pkg

TM 3/16-6 Bit Pkg
TM 1/4-4 Bit Pkg
TM 1/4-6 Bit Pkg
TM 3/8-6 Bit Pkg
TM 3/8-18 Bit Pkg
TM 3/8-24 Bit Pkg
TM 1/2-6 Bit Pkg
TM 1/2-18 Bit Pkg
TM 3/16-4 Bit Pkg
TM 3/16-6 Bit Pkg
TM 1/4-4 Bit Pkg
TM 1/4-6 Bit Pkg
TM 1/4-18 Bit Pkg
TM 3/8-6 Bit Pkg
TM 3/8-18 Bit Pkg
TM 3/8-24 Bit Pkg
TM 1/2-6 Bit Pkg
TM 1/2-18 Bit Pkg
TM 5/8-8 Bit Pkg
3/16"
3/16"
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1/2"
3/16"
3/16"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1/2"
5/8"
4"
6"
4"
6"
6"
18"
24"
6"
18"
4"
6"
4"
6"
18"
6"
18"
24"
6"
18"
8"
2-1/8"
3"
2-1/8"
3"
3"
16"
21-1/2"
3"
16"
2-1/8"
3"
2-1/8"
3"
16"
3"
16"
21-1/2"
3"
16"
5-1/2"
12
12
12
12
12
12
12
12
12
36
36
36
36
36
36
36
36
36
36
36
www.us.hilti.com
2.9
Rotary Hammer Drill
Hilti TE 2 Rotary Hammer Drill

Designed for Drilling Anchor Holes in Concrete and Masonry
TE-C (SDS)
Features
Reverse Switch
Variable Speed Switch
Padded Side Handle
Ergonomic Design
Rotation with Hammer
Fixed TE-C+ chuck design
Technical Data
Power input
600 W
Single impact energy

1.33 ft-lb
Speed under load

1st speed: 0930 rpm
Hammering speed under load

04600 blows/min
Tool dimensions
13.5" x 7.9" x 3.1"
Tool weight
5.1 lb
TE 2 rotary hammer:
powerful and efficient
The standard class

Two drilling modes: rotation
with hammer, rotation only
Electronic variable speed switch
for infinite speed regulation
Reverse switch
Two year Full Service Tool
Support
The TE 2 is the basic model in the

TE 2 line of Hilti light-duty rotary
hammers. It is designed for drilling
anchor holes and small diameter
through-holes in concrete and
masonry. In use, it is exceptionally
powerful and comfortable.
Recommended drilling
range:
Concrete and masonry:
Drilling steel: up to 1/2"
diameter
Drilling wood: up to 3-1/2"
diameter hole saw
Drilling performance in concrete

with 5/16" diameter drill bit
Up to 500 mm/min
3/16"
CONCRETE
3/16"
TE 2 Feature Comparison
Reverse Switch
Padded Side Handle
Ergonomic Design
Rotation with Precision Hammering
Rotary Drilling:
Speed 1 (0930 rpm)

Speed 2 (02200 rpm)
Fixed TE-C+ Chuck Design

Quick Release TE-C+ Chuck Design
TE 2
TE 2-S
TE 2-M
3/4"
5/16"

all models. See product
description for details.
R e p a i r
P r o g r a m
Item No.
Description
00336786
TE 2 Deluxe 120 V
Includes TE 2 rotary hammer complete with 13 ft supply cord,
side handle, depth gauge, dust shield, impact resistant Hilti
case and operating instructions
00336799
TE 2 Standard 120 V
Includes TE 2 rotary hammer complete with 13 ft supply cord,
side handle, depth gauge, dust shield and operating
instructions. Packaged in cardboard box.
Accessories
Item No.
Description
00060208
Keyless Chuck
For rotation only drilling. Requires chuck
spindle item no. 00060459 (sold below)
00240704
www.us.hilti.com
Keyed Chuck
2.25
KWIK-CON Masonry
Screws see page:
7.41
Dust removal see page:
00060459
Chuck Spindle
2.30
2.10
Rotary Hammer Drill
Hilti TE 2-S Rotary Hammer Drill

Precision Drilling for Anchor Holes in Concrete, Masonry and Brittle Materials
TE-C (SDS)
Features
Reverse Switch
Padded Side Handle
Ergonomic Design
Rotation with Precision
Hammering
Rotary drilling:
Speed 1 (0930 rpm)
Fixed TE-C+ chuck design
Technical Data
Power input
600 W

precision hammer drilling: 0.44 ft-lb
full hammer drilling: 1.33 ft-lb
Speed under load

0930 rpm
Precision hammering speed

02400 blows/min
Full hammering speed

04600 blows/min
Tool dimensions
TE 2-S rotary hammer

for specialized drilling
13.5" x 7.9" x 3.1"
Tool weight
5.3 lb
Drilling performance in mediumhard concrete with 5/16"

diameter drill bit
Up to 500 mm/min
3/16"
CONCRETE
3/16"
3/4"
For all its power, the TE 2-S can also

hammer lightly when drilling. Thanks
to innovative technology, brittle
materials such as tile, marble
or stone, can be drilled at full speed
but with only 30% of the full
impact energy. The TE 2-S also has
rotation with hammering at 100%
full impact energy for a real impact
on concrete.
5/16"
The specialized class

Three drilling modes: rotation
with hammer, rotation with
precision
hammer or rotation only
Precision hammer drilling at
30% of full impact for drilling
anchor holes in brittle materials
Reverse switch for quick
fastener removal
Support
R e p a i r
P r o g r a m
Reverse Switch
Padded Side Handle
Ergonomic Design
Rotary Drilling:
Speed 1 (0930 rpm)

Speed 2 (02200 rpm)

www.us.hilti.com
2.25
KWIK-CON Masonry
Screws see page:
7.41
2.11
Concrete masonry, tile and

stone: 3/16" to 3/4" diameter
Drilling steel: up to 1/2"
diameter
Drilling wood: up to 3-1/2"
diameter hole saw
TE 2
TE 2-S
TE 2-M
Item No.
Description
00336763
TE 2-S Deluxe 120 V

Includes TE 2-S rotary hammer complete with 13 ft supply
cord, side handle, depth gauge, dust shield, impact resistant
Hilti case and operating instructions
Accessories
Item No.
Description
00060208
Keyless Chuck
00240704
Keyed Chuck
For rotation only drilling. Requires chuck spindle
item no. 00060459 (sold below)
2.30
range
00060459
Chuck Spindle
Rotary Hammer Drill
Hilti TE 2-M Rotary Hammer Drill

The Multifunctional Tool for Concrete, Masonry, Brittle Material, Wood and Metal
TE-C (SDS)
Features
Reverse Switch
Padded Side Handle
Ergonomic Design
Rotation with Precision
Hammering
Rotary drilling:
Speed 1 (0930 rpm)
Speed 2 (02200 rpm)
Quick Release TE-C+ chuck
design
Applies to all TE 2 models.
Technical Data
Power input
600 W

precision hammer drilling: 0.44 ft-lb
full hammer drilling: 1.33 ft-lb
Speed under load

1st speed: 0930 rpm
Tool dimensions
14.1" x 7.9" x 3.1"
Tool weight
5.7 lb
TE 2-M rotary hammer

for multifunctional use
over a wide working
range
All trades will have a firm grip on
light-duty drilling applications with
the Hilti TE 2-M. It combines the
high performance of a rotary hammer with the versatility of a camaction drill. Its chuck interface
permits the use of keyed and keyless chucks, and, with its
hammering power regulation, tiles
and stone can be drilled under
control, while the two speeds
facilitate the drilling of wood and
metal.
The multifunctional
class
range
Interface for TE-C chuck and

1/2" Jacobs style quickrelease chuck
4-mode function selection
switch: rotation with hammer,
rotation with precision hammer
(drilling 30% of full impact),
rotation only1st and 2nd
speeds for drilling wood, metal
and brick
Reverse switch for quick
fastener removal
Support
Concrete, masonry, tile and

stone, 3/16" to 3/4"
Drilling wood, up to 3 1/2"
diameter hole saw
Drilling steel, up to 1/2"
Reverse Switch
Padded Side Handle
Ergonomic Design
Rotary Drilling:
Speed 1 (0930 rpm)

Speed 2 (02200 rpm)

Description
00340956
TE 2-M Deluxe 120 V
Up to 500 mm/min
3/16"
CONCRETE
3/16"
3/4"
5/16"

TE 2
TE 2-S
TE 2-M
R e p a i r
P r o g r a m
Item No.
Drilling performance in
medium-hard concrete
with 5/16" diameter drill bit
Includes TE 2-M rotary hammer complete with 13 ft supply

cord, side handle, depth gauge, dust shield, impact resistant
Hilti case and operating instructions
www.us.hilti.com
2.25
KWIK-CON Masonry
Screws see page:
00354683
TE-C Replacement Chuck (TE 2-M)
7.41
00338905
1/2" Quick-Release Keyless Chuck

(TE 2-M only)
2.30
2.12
Rotary Hammer Drill
Hilti TE 5 A Cordless Tool

A Versatile Tool For Concrete, Wood And Steel Applications
TE-C (SDS)
* Excludes consumable battery pack
Technical Data TE 5 A
Power input
350 W
Voltage
24 V
No-load speed
0820 rpm
Hammering speed
04000 blows/min

1.5 ft-lb
Weight with BP 40 battery

9.3 lb
Weight with BP 72
Extended Life battery
Advantages
10.6 lb
Dimensions with BP 40 battery

(LxWxH) 15-5/8" x 3" x 7-3/4"
Dimensions with BP 72 battery

(LxWxH) 15-5/8 x 4-5/8 x 7-3/4"
Battery capacity
BP 40: 40 Wh (24 V x 1.7 Ah)
BP 72: 72 Wh (24 V x 2.5 Ah)
3/16"
CONCRETE
3/16"
5/8"
3/8"
Steel: Up to 1/2"
Hole Saw: up to 5"
Cordless convenience for

hammer/rotary drilling
when extension cords are a
problem
Choice of two battery packs
BP 40 for standard use or
BP 72 Extended Life battery for
more power reserves
Chuck interface for easy two
finger change from Jacobs
style chuck to TE-C+ (SDS+) to
an angle chuck
Variable speed for brittle

materials or screw fastening
Reversible
Support
Accessory Program
High performance, carbide
tipped TE-C drill bits
KWIK-CON driver and KWIK-CON
drill bits for rapid installation and
removal of the KWIK-CON
masonry anchor system
Keyless and keyed chucks

High Performance steel bits in
M2 steel, titanium steel, cobalt
steel
Fast cutting, bi-metal hole saws
Accepts TE-C carbide bits up to
5/8", steel bits up to 1/2" and
hole saws up to 5"
Item No.
Description
00201688
TE 5 A Standard
Equipped with TE-C+ (SDS+) chuck, impact resistant Hilti
case, side handle, dust guard, cleaning cloth, Hilti grease,
safety precautions and operating instructions
00254372
R e p a i r
P r o g r a m
www.us.hilti.com
2.25
Chucks see page:
2.24
00254371
TE 5 A - BP72 - TCU 24H Deluxe

Includes BP72 (2.4 Ah) battery, TCU 24H charger (115 V),
TE-C+ (SDS+) chuck, impact resistant Hilti case, side
handle, dust guard, cleaning cloth, Hilti grease, safety
precautions and operating instructions
00254481
TE 5 A - BP40 - Rapid Charger Deluxe
Wehr
2
7
w
o
24V of P
Includes BP40 (1.7 Ah) battery, rapid charger (115 V),

charger adapter, TE-C+ (SDS+) chuck, impact resistant Hilti
00254482
TE 5 A - BP72 - Rapid Charger Deluxe

Includes BP72 (2.4 Ah) battery, rapid charger (115 V),
charger adapter, TE-C+ (SDS+) chuck, impact resistant Hilti
KWIK-CON Masonry
Screws see page:
2.13
TE 5 A - BP40 - TCU 24H Deluxe

Includes BP40 (1.7 Ah) battery, TCU 24H charger (115 V),
TE-C+ (SDS+) chuck, impact resistant Hilti case, side
handle, dust guard, cleaning cloth, Hilti grease, safety
precautions and operating instructions
7.41
Batteries
Item No.
Description
00201714
BP40 Standard Battery
2.14
00331530
BP72 Extended Life Battery
BP 40
BP 72
Rotary Hammer Drill
TE 5 A Accessories
Battery Chargers & Adapter
TCU 7/36 Universal Power Charger
Item No.
Description
00337011

For all current Hilti battery types (Hilti batteries BP6-86,BP72,
BP60, BP40, SBP10 and SBP12). With conditioning charge
mode for refreshing. Requires Adapter TCU 7/36 CA (item no.
00335475 sold below) for use with BP 72 and BP 40
batteries.
00335475
Adapter TCU 7/36 CA
TCU 7/36
TCU 7/36 CA
To charge batteries BP 40, BP 60 and BP 72 on TCU 7/36

Universal Charger
Dust Removal System

TE 5 Dust Removal System Module
Complete with fitted dust container, dust container cover and extraction head.
Maximum drilling capacity 11/16".
Hilti Battery
Approximate
Charging Time
BP-6-86
BP 40
BP 60
BP 72
RB 10
SBP 10
SBP 12
SFB 105
SFB 120
32 min
20 min
25 min
30 min
15 min
15 min
15 min
35 min
35 min
Technical Data TE 5 DRS

Power input
Max 60 W
Suction capacity
17.7 cfm
Max bit length

Item No.
Description
00201390
00201397
00258106
00258107
Dust Removal Module in expanded plastic Hilti case*

Dust Removal Module in cardboard box*
Suction Tube Assembly-short (not shown)
Suction Tube Assembly-tall (not shown)
4" to 6" standard, up to 8" using tall

suction tube assembly (sold separately)
For use with TE-C drill bits

For use with 8" long bits

* TE 5 drill sold separately
www.us.hilti.com
2.14
Rotary Hammer Drill
NEW!
Hilti TE 6-S Rotary Hammer

Despite its power, the TE 6-S can also hammer lightly when drilling
TE-C (SDS)
Technical Data
Power input
650 W
Single impact energy,

full hammering
1.33 ft-lb

precision hammering
0.44 ft-lb
Speed under load

0-880 rpm
Hammering speed,
full hammering
0-5100 blows/min
Hammering speed,
precision hammering
Advantages
Comfortable switch Easy
grip electronic variable speed
switch for complete speed
control. Synchronized function
selection switch allows user to
easily change mode of
operation.
Quick change Simple
interface allows user to quickly
change from TE-C to angle
chuck or 1/2" Jacobs style
chuck.
0-2700 blows/min
Machine Dimensions
12.6" x 8.5" x 3.0"
Machine Weight
6.2 lb
medium-hard concrete,
with 3/8" dia drill bit
Uo to 550 mm/min
3/16"
CONCRETE
5/16"
1"
9/16"
2-way power Full power

forward/reverse allows user to
drill as well as remove stuck
drill bits, drive and remove
concrete screws.
Good grip Ergonomically
padded side handle with
D-handle grip to dampen
vibration and add more control.
Full hammering power for fast
drilling in concrete and
masonry
Precision rotary hammer drilling
with 2/3 hammer reduction for
brittle materials
Rotation only drilling for wood

and steel
Optional Dust Removal System
for dust free drilling
Recommended drilling range
drilling anchor and through
holes in concrete and masonry,
3/16" to 1" diameter; drilling
wood, up to 3 1/2" diameter;
drilling steel, up to 1/2"
diameter; driving anchor screws
Item No.
Description
00369025
Hilti TE 6-S Deluxe (Specialized)

TE 6-S complete with 13 ft. supply cord, side handle, dust
shield, impact resistant Hilti case and operating instructions
00370083
Hilti TE 6-S Professional
Includes TE 6-S rotary hammer complete with dust removal

module
00370028
Dust removal module in cardboard box
Chucks
Item No.
Description
00070639
1/2" Keyless Chuck (Quick Release)

For smooth shank bits up to 1/2" diameter, for rotary drilling
only
00070640
1/2" Keyed Chuck Assembly

For smooth shank bits up to 1/2" diameter, for rotary drilling
only
00070591
www.us.hilti.com
TE-AC Angle Chuck

For right angle drilling with TE-C+ (SDS+) drill bits
(with/without hammering action) in places where access is
limited. Maximum 5/8" diameter bit
2.25
2.15
Rotary Hammer Drill

NEW!
Hilti TE 6-C Rotary Hammer
A rotary hammer with enough chiseling power for most concrete clean-up work
TE-C (SDS)
Technical Data
Power input
650 W

full hammering
1.33 ft-lb
Speed under load

0-880 rpm
Hammering speed,
full hammering
0-5100 blows/min
Machine Dimensions
12.6" x 8.5" x 3.0"
Machine Weight
Features & Benefits

Light weight and perfectly
balanced design
Oversized and accessible
controls for easy operation
D-handle grip with padded side
handle

Forward/reverse switch
Chisel can be adjusted 360 for
just the right angle
Ideal for overhead work

Interface for TE-C chuck and
quick-release chuck
Drilling with full hammering
action
Rotation only drilling
6.2 lb
medium-hard concrete,
with 3/8" dia drill bit
Up to 550 mm/min
Chiseling function (TE 6-C only)
3/16"
5/16"
Item No.
Description
00369036
Hilti TE 6-C Deluxe (Chiseling)
TE 6-C complete with 13 ft. supply cord, side handle, dust

shield, impact resistant Hilti case and operating instructions
00370028
Dust removal module in cardboard box
CONCRETE
1"
9/16"
Chucks
Item No.
Description
00070639

For smooth shank bits up to 1/2" diameter,
for rotary drilling only
00070640

For smooth shank bits up to 1/2" diameter,
for rotary drilling only
00070591
TE-AC Angle Chuck

For right angle drilling with TE-C+ (SDS+) drill bits
(with/without hammering action) in places where access is
limited. Maximum 5/8" diameter bit
www.us.hilti.com
2.25
2.16
Rotary Hammer Drill
The Hilti TE 6-A Cordless Rotary Hammer Drill

An Innovative Drilling System for Complete Mobility
With Unmatched Power Reserves
TE-C (SDS)
Technical Data TE 6-A

Power input
375 W
Voltage
36 V
Weight of machine including BP

6-86 battery
10.4 lb
Dimensions (LxWxH)
13" x 3.9" x 8.9"
Battery capacity
BP 6-86: 86 Wh (36 V x 2.4 Ah)
No-load speed
0890 rpm
Hammering speed
05000 blows/min
Advantages
Accessory Program
1.1 ft-lb
Optional belt adapter for

overhead use
TCU 7/36 Universal Charger
High performance carbide
tipped TE-C drill bits
from 3/16" to 5/8" diameter
KWIK-CON driver and KWIKCON drill bits for rapid
installation and removal of
KWIK-CON masonry anchor
system
Keyed and keyless chucks
Dust-tight encapsulation and

permanent lubrication
3/16"
CONCRETE
3/16"
5/8"
3/8"
Wood: up to 3/4"
Metal: Up to 3/8"
36 Volt battery with deep discharge prevention

Electronic switch for variable speed regulation
Selector switch to change from hammer drilling to rotary only drilling
Forward/reverse switch with transport lock
Exceptional number of holes produced in concrete per charge
Removable TE-C+ (SDS+) chuck allows quick change to keyed,
keyless, or TE-AC angle chuck
Padded side handle that rotates 360 for added operator comfort
Ergonomically designed grip
R e p a i r
Item No.
Description
00332013
TE 6-A Standard
Equipped with TE-C+ (SDS+) chuck, side handle, dust shield,
cleaning cloth, operating instructions and safety precautions.
Packed in an impact resistant Hilti case.
P r o g r a m
00334951
TE 6-A Deluxe
cleaning cloth, BP 6-86 battery, TCU 7/36 universal charger,
operating instructions and safety precautions. Packed in an
impact resistant Hilti case.
00334952
2.25
KWIK-CON Masonry
Screw System see page:
Wehr
6
8
w
o
P
36V of

cleaning cloth, two (2) BP 6-86 batteries, TCU 7/36 universal
charger, operating instructions and safety precautions.
Packed in an impact resistant Hilti case.
www.us.hilti.com
TE 6-A Contractor
00334953
TE 6-A Utility
cleaning cloth, two (2) BP 6-86 batteries, TCU 7/36 universal
charger, 1/2 quick release keyed chuck, operating
instructions and safety precautions. Packed in an impact
resistant Hilti case.
7.41
2.17
Rotary Hammer Drill
TE 6-A Accessories
Item No.
Description
00333969
00333848
BP 6-86 Battery
TE 6-A BAP Belt Adapter
Technical Data BP 6-86 Battery

Voltage
36 V
Battery capacity
For attaching the battery to a waist belt. Reduces the working

weight of the machine to 6.2 lb, making it ideal for repetitive
drilling, particularly when working overhead.
36 V x 2.4 Ah = 86 Wh
Weight
4.6 lb
Deep discharge prevention

Right of technical changes reserved
Battery Charger & Adapter

Item No.
Description
00337011

For all current Hilti battery types (Hilti batteries BP6-86,BP72,
BP60, BP40, SBP10 and SBP12). With conditioning charge
mode for refreshing.
00335475
TCU 7/36
Adapter TCU 7/36 CA

To charge batteries BP 40, BP 60 and BP 72 on TCU 7/36
Universal Charger
Hilti Battery
Approximate
Charging Time
BP-6-86
BP 40
BP 60
BP 72
RB 10
SBP 10
SBP 12
SFB 105
SFB 120
32 min
20 min
25 min
30 min
15 min
15 min
15 min
35 min
35 min
TCU 7/36 CA
www.us.hilti.com
2.18
Rotary Hammer Drill
Hilti TE 15 Rotary Hammer Drill

Greater Comfort And Longer Tool Life Expectancy
TE-C (SDS)
Technical Data TE 15
Power input
650 W
Voltage
115 V AC
Frequency
5060 Hz

03800 blows/min

1.6 ft-lb
Machine weight
8.3 lb
Dimensions (LxWxH)
14" x 3.5" x 7.5"
1/2" diameter
up to 15"/min in 4000 psi concrete
Speed under load

0700 rpm
3/16"
CONCRETE
3/8"
1"
5/8"
Advantages
Accessory Program
Balanced, well-positioned controls, ergonomic design, and features for

comfortable drilling helps keep users from tiring when drilling for long
periods
Smooth starting of holes due to integrated electronics and infinite
speed regulation
Hammering cut-out
Dust removal system
Modular design makes replacement of worn parts simple
Compact design provides good accessibility in tight spaces
Two year Full Service Tool Support
Carbide-tipped drill bits:

TE-CX 3/16" to TE-C-S 1"
diameter
TE-C+ (SDS+) Chuck Assembly
TE-C+ Carbide-tipped
Unreinforced Masonry Drill Bits
1/2" Keyless Adapter
TE-AC Angle Chuck
Wood: up to 1-1/4"
Steel: Up to 1/2"
R e p a i r
P r o g r a m
Item No.
Description
00228862
TE 15 Deluxe
Includes TE 15 Rotary hammer with impact resistant Hilti
case, dust shield, cleaning cloth, lubricant spray, operating
instructions, safety precautions
00228904
TE 15 Deluxe Grounded 115 V

Includes TE 15 Rotary hammer with impact resistant Hilti
case, dust shield, cleaning cloth, lubricant spray, operating
instructions, safety precautions
www.us.hilti.com
Masonry Bits see page:
2.27
Chucks see page:
2.24
2.30
2.19
Rotary Hammer Drill
Hilti TE 15-C Mini Combihammer

Provides Reliability And Versatility
TE-C (SDS)
Technical Data TE 15-C

Power input
710 W
Voltage
115 V AC
Frequency
5060 Hz

03850 blows/min

1.6 ft-lb
Machine weight
8.7 lb
Dimensions: (LxWxH)
14" x 3.5" x 7.5"
Drilling Performance
1/2" diameter
up to15"/min in 4000 psi concrete
Speed under load
Advantages
Accessory Program
Three modes of operation: rotary, rotary-hammer drill and chipping

Electronically controlled variable speed switch
Smooth starting of holes due to integrated electronics and infinite
speed regulation
Forward/reverse rotation switch
Hammering cut-out
Modular design makes replacement of worn parts simple
Compact design provides good accessibility in tight spaces
TE-CX 3/16" to TE-C-S 1"

diameter
TE-C+ (SDS+) Chuck Assembly
TE-C+ Carbide-tipped
Unreinforced Masonry Drill Bits
1/2" Keyless Adapter
TE-AC Angle Chuck
0700 rpm
3/16"
CONCRETE
3/8"
1"
5/8"
Wood: up to 1-1/4"
Steel: Up to 1/2"
Item No.
Description
00308361
TE 15-C Deluxe (115 V)
R e p a i r
P r o g r a m
Includes impact resistant Hilti case, dust shield, cleaning

cloth, lubricant spray, operating instructions, safety
precautions
00308353
TE 15-C Deluxe (230 V)

Includes impact resistant Hilti case, dust shield, cleaning
cloth, lubricant spray, operating instructions, safety
precautions
www.us.hilti.com
Masonry Bits see page:
2.27
Chisels TE-C see page:
2.29
Chucks see page:
2.24
2.30
2.20
Rotary Hammer Drill
Hilti TE 18-M Rotary Hammer Drill

Handles A Wide Variety Of Base Materials With Speed And Efficiency
TE-C (SDS)
Technical Data
Power input
720 W
Voltage
115 V
Frequency
5060 Hz

03800 blows/min
Speed
1st Speed: 0700 rpm
2nd Speed: 01200 rpm
3rd Speed: 02000 rpm
Weight
9.8 lb
Dimensions (LxWxH)
14" x 3-1/2" x 8-1/2"
Drilling rate in 4000 psi concrete

3/8" diameter bit = up to 17"/min
3/16"
CONCRETE
3/8"
1"
5/8"
Steel: Up to 1/2"
Advantages
Accessory Program
TE-CX 3/16" to TE-C+ 11/16",

TE-C-S 3/4" to 1"
TE-C+GB Cruciform Bits 1-1/8"
to 1-1/2"
TE-C-BK Thin Wall Core Bits
1-1/4" to 2-1/2"
Hole Saws 9/16" to 4"
Wood Bits 1/4" to 1-1/4"
Steel Bits 1/8" to 1/2"
TE-AC Right Angle Chuck
Water swivel for diamond bits
SM or BT 1/2" to 1-1/2"
Three speeds always the right speed for the job

TE-C+ (SDS+) and Jacobs chuck for easy, secure bit changes
Shift from hammer drilling to rotation only drilling while in operation
2 drilling modes: Hammer with rotation or rotation only
Reversing switch
Diamond coring with 1/2" chuck and water swivel
Modular design for easy servicing and repair
UL listed double insulated construction
R e p a i r
Item No.
Description
00050524
TE 18-M 115 V Deluxe Drill
P r o g r a m
Deluxe kit includes TE 18M tool, impact resistant Hilti case,

key type chuck, dust protector, spray lubricant,
master parts list, cleaning cloth, blow-out bulb,
operator's instruction manual
00070591
TE-AC Angle Chuck
Maximum hammer drilling performance for

limited access spaces
www.us.hilti.com
00050835
Water Swivel for Diamond Bits
For use with SM or BT Diamond Core bits 1/2" to 1-1/2"

(*requires 1/2" Jacobs Style Chuck)
2.25
2.30
2.21
Rotary Hammer Drill
Hilti TE 25 Hammer Drill

Improved Comfort And Lighter Weight Make The Powerful TE 25
The Ideal Hammer Drill For Medium To Heavy-Duty Anchoring
TE-C (SDS)
Power input
830 W
Voltage
115 V
Frequency
5060 Hz

03720 blows/min
Speed loaded
1st Speed: 0310 rpm
2nd Speed: 0640 rpm

2.8 ft-lb
Machine weight
Advantages
Accessory Program
TE-C Carbide Tipped Drill Bits

3/16" to 1"
Cruciform 1-1/8" to 1-1/2"
Thin Wall Core Bits 1-1/4" to
3-1/2"
Twist Bits with Keyless Chuck
Wood to 1-1/4"
Steel to 1/2"
Superior power and performance

High reliability
Long life expectancy
Ergonomic grip and switch design with ideally
positioned supply cord
Versatile: Ideal for drilling through-hole penetrations
and anchor holes in concrete, stone or rock,
masonry and chiseling. Also uses high speed steel twist bits for
occasional drilling in wood/steel
Chipping capability with optional adapter
10.8 lb
Dimensions (LxWxH)
17" x 4" x 8-3/4"

with 9/16" diameter bit
up to 10"/ min
3/16"
CONCRETE
1/2"
3-1/2"
3/4"
Steel: Up to 1/2"
Hole Saw: up to 5"
Item No.
Description
00308330
TE-25 115 V Deluxe Kit

Includes impact resistant Hilti case, dust shield, depth gauge,
side handle, spray lubricant, blow-out bulb, cleaning cloth,
instruction manual, master parts list
00308324
R e p a i r
P r o g r a m
TE-25 220 V Deluxe Kit

00308334
TE-25 115 V Grounded Deluxe Kit

00030211
www.us.hilti.com
Chisel Adapter
2.25
Cruciform Bits see page:
2.27
2.30
2.22
Rotary Hammer Drill
Hilti TE 25S Added Protection Tool

Bringing Power And Performance To Repetitive Drilling Applications
TE-C (SDS)
Technical Data TE 25S

Power input
830 W
Voltage
115 V
Frequency
5060 Hz
on
en soluti
The prov e drilling in
it
for term agement
n
Pest Mxtearnal drill stop
no e
round.
to drag a

03720 blows/min
Speed loaded
1st Speed: 0310 rpm
2nd Speed: 0640 rpm

2.8 ft-lb
Machine weight
11 lb
Dimensions (LxWxH)
22-1/2" x 4" x 8-3/4"

with 9/16" diameter bit
up to 10"/min
3/16"
CONCRETE
1/2"
3-1/2"
3/4"
Steel: Up to 1/2"
Hole Saw: up to 5"
Advantages
Accessory Program
Innovative switch design allows access from back or top of drill

Integrated electronic drill stop device turns drill off when drill bit
encounters grounded metal
Comfortable and convenient to operate
Extended rear handle for operator comfort when drilling in downward
position
TE-C Carbide Tipped Drill Bits

3/16" to 1"
Cruciform 1-1/8" to 1-1/2"
Thin Wall Core Bits 1-1/4" to
3-1/2"
Twist Bits with Keyless Chuck
Wood to 1-1/4"
Steel to 1/2"
R e p a i r
P r o g r a m
Description
Item No.
00314361
TE 25S 120 V Deluxe Kit

Complete with TE-C+ (SDS+) chuck, supply cord, impact
resistant Hilti case, Hilti spray, dust guard, cleaning cloth and
operating instructions
www.us.hilti.com
2.27
Cruciform Bits see page:
2.27
Extension Cords see page:
2.50
2.23
Rotary Hammer Drill
Chucks
Increase your productivity using Hilti
rotary hammer drill accessories.
TE-AC Angle Chuck shown at left.
Item No.
Description
00240704
SR Keyed Chuck Assembly
Shown at right
For use with SR 16 or TE 2 and TE 2-S with chuck spindle

(item 00060459)
00240647
00090411
SR Keyless Chuck Assembly

For TM7SIII VSR
00060372
Keyless Chuck Assembly TE-C+ BFH

Includes Items 00060459 and 00060208
00060459
Keyless Chuck Spindle TE-C+ BFH
For rotation only drilling with TE 2, TE 2-S, TE 10, TE 10 A, TE 12, TE 12 S,TE 17, TE 22. Requires Keyless
Chuck TE-C+ BF (item 00060208) or Keyed Chuck (item 00240704 or 00090411)
00060208
Keyless Chuck TE-C+ BF

For insert tools with smooth shanks up to 1/2" diameter (without hammering action)
For use with TE 2-M

Item No.
Description
00354683
00338905
TE-C Replacement Chuck (TE 2-M)

1/2" Quick-Release Keyless Chuck (TE 2-M only)
Shown at right
For use with TE 1, TE 5, TE 5 A, TE 6-A, TE 14, TE 15, TE 15-C, TE 18-M

Item No.
Description
00250764
SDS Chuck Assembly
Shown at right
For TE-C+(SDS+) drill bits
00070638
TE-C Chuck Assembly (not shown)
00070591
TE-AC Angle Chuck (Right Angle Chuck)*
For old style TE-C bits (2-groove connection end)
For right angle drilling with TE-C+(SDS+) drill bits (with/without hammering action) in places where
access is limitedmaximum 5/8" diameter bit. *Not for use with TE 1.
00070639

For smooth shank bits up to 1/2" diameter, for rotary drilling only
00070640

For smooth shank bits up to 1/2" diameter, for rotary drilling only
00075283
Replacement Chuck Key (not shown)
For use with TE 24, TE 25 and TE 25S

Item No.
Description
00277057
SDS Chuck Assembly
Shown at right
For TE-C+(SDS+) drill bits
00030201
Keyless Chuck Assembly
For smooth shank bits up to 1/2" diameter
00030211
Chisel Adapter Chuck
For use with TE-C chisels in TE 24, TE 25 and TE 25S
Spline Shank to SDS+ Adapter: For Use With TE-C+ Bits

Item No.
Description
00001862
Adapter Spline to SDS+

Allows use of TE-C+ bits in spline drive drills
www.us.hilti.com
2.24
Rotary Hammer Drill
TE-CX Carbide Tipped Bits

10mm
Taking A Hard-Headed Approach To Longer Life

Providing Superior Drilling Performance
Larger Flute Gullets
Allows an increase in drilling
speed by as much as 15%.
Double-Helical Fluting
Solid Carbide Head
Allows faster dust removal and less

contact area with the hole wall.
Less friction means less wear on
your rotary hammer drill, increasing tool life up to 20%.
Precisely oriented, solid carbide

head for rounder holes producing
up to 70% longer life and rebar
resistance.
Red Ring
Red ring signifies Hilti quality. Bits
are manufactured under ISO 9001
and ISO 14001 certification in the
Hilti manufacturing plant Tulsa,
Oklahoma.
Large Markings
Larger markings for easier
size identification
TE-CX/TE-C+ Metric Carbide Tipped and Helical Bits
TE-CX Carbide Tipped and Helical Drill Bits

(SDS & ANSI)
Item No.
Description
Diameter x Length (in.)
00256099
00205299
00256100
00256101
00256102
00205309
00205310
00205311
00256106
00205316
00205320
00256107
00205324
00205326
00205327
00205328
00205339
00205340
00205352
00205354
00205355
Bit TE-CX 3/16-4

Bit TE-CX 3/16-6
Bit TE-CX 3/16-8
Bit TE-CX 3/16-12
Bit TE-CX 3/16-16
Bit TE-CX 1/4-4
Bit TE-CX 1/4-6
Bit TE-CX 1/4-8
Bit TE-CX 1/4-12
Bit TE-CX 5/16-6
Bit TE-CX 5/16-12
Bit TE-CX 5/16-18
Bit TE-CX 3/8-6
Bit TE-CX 3/8-12
Bit TE-CX 3/8-18
Bit TE-CX 3/8-24
Bit TE-CX 7/16-6
Bit TE-CX 7/16-18
Bit TE-CX 1/2-6
Bit TE-CX 1/2-12
Bit TE-CX 1/2-18
Effective
Drilling Depth
2"
4"
5-1/2"
9-1/2"
13-1/4"
2"
4"
5-1/2"
9-1/2"
4"
9-1/2"
15-1/4"
4"
9-1/2"
15-1/4"
21-1/4"
4"
15-1/4"
4"
9-1/2"
15-1/4"
TE-C+ Carbide Tipped and Helical Drill Bits

00028040
00028041
00028042
00028043
00028044
00028045
00028047
00028048
00028618
00028619
00028620
00028621
00028622
00028623
00028624
00028625
00028626
00028627
00028060
2.25
Bit TE-C+ 9/16-6

Bit TE-C+ 9/16-12
Bit TE-C+ 9/16-18
Bit TE-C+ 5/8-8
Bit TE-C+ 5/8-12
Bit TE-C+ 5/8-18
Bit TE-C+ 11/16-12
Bit TE-C+ 11/16-18
Bit TE-C-S 3/4-8
Bit TE-C-S 3/4-12
Bit TE-C-S 3/4-18
Bit TE-C-S 13/16-18
Bit TE-C-S 27/32-8
Bit TE-C-S 27/32-12
Bit TE-C-S 7/8-10
Bit TE-C-S 7/8-18
Bit TE-C-S 1-10
Bit TE-C-S 1-18
Bit TE-C-S 1-27
3-1/2"
9-1/2"
15-1/2"
5-1/2"
9-1/2"
15-1/4"
9-1/2"
15-1/4"
5-1/2"
9-1/2"
15-1/4"
15-1/4"
5-1/2"
9-1/2"
7-1/2"
15-1/4"
7-1/2"
15-1/4"
24-1/4"
Item No.
Description
Diameter x Length (mm)
00077833
00205297
00205298
00205300
00205304
00205305
00205306
00205315
00205317
00205322
00205325
00205330
00205331
00205334
00205342
00205343
00205344
00205356
00205357
00205358
00205360
00205364
00205366
00205368
00205372
00205373
00333739
00205375
00205376
00028002
00028003
00028004
00028005
00028011
00028012
00028016
00028017
Bit TE-C+ 4.5/11

Bit TE-CX 5/12
Bit TE-CX 5/15
Bit TE-CX 5/17
Bit TE-CX 6/12
Bit TE-CX 6/17
Bit TE-CX 6/22
Bit TE-CX 8/17
Bit TE-CX 8/22
Bit TE-CX 8.5/17
Bit TE-CX 9/22
Bit TE-CX 10/17
Bit TE-CX 10/22
Bit TE-CX 10/47
Bit TE-CX 12/17
Bit TE-CX 12/22
Bit TE-CX 12/27
Bit TE-CX 14/17
Bit TE-CX 14/22
Bit TE-CX 14/27
Bit TE-CX 14/47
Bit TE-CX 15/17
Bit TE-CX 15/27
Bit TE-CX 15/47
Bit TE-CX 16/17
Bit TE-CX 16/22
Bit TE-CX 16/27
Bit TE-CX 16/47
Bit TE-CX 16/61
Bit TE-C-S 18/22
Bit TE-C-S 18/47
Bit TE-C-S 20/22
Bit TE-C-S 20/32
Bit TE-C-S 24/27
Bit TE-C-S 25/27
Bit TE-C-S 28/27
Bit TE-C-S 28/48
Effective
Drilling Depth
2"
2"
3"
4"
2"
4"
6"
4"
6"
4"
6"
4"
6"
15-1/2"
4"
6"
7-1/2"
4"
5-9/10"
7-7/8"
15-3/4"
4"
7-7/8"
15-3/4"
4"
5-9/10"
7-7/8"
15-3/4"
21-5/8"
6"
15-1/2"
6"
10"
7-1/2"
7-1/2"
7-1/2"
15-1/2"
This inspection mark indicates that Hilti metric rotary hammer

drill bits comply with the requirements for carbide-tipped drill
bits used to drill anchor holes for metric anchors.
Rotary Hammer Drill

TE-CX/TE-C Bit Packages
Item No.
Description
Qty
Effective
Drilling Depth
00331631
00334641
00331632
00331633
00334642
00331634
00334643
00331635
00334644
00334648
00334645
00028417
00334646
00028418
00334656
00334647
00332314
00315224
00332317
00332320
00332323
00315227
00315230
00332326
00332329
00315232
00332332
00332335
00315234
00332338
00332341
00332344
00332353
00332356
00205359
00028886
00028887
00028888
00028889
Bit TE-CX 3/16-6

Bit TE-CX 3/16-12
Bit TE-CX 1/4-4
Bit TE-CX 1/4-6
Bit TE-CX 1/4-12
Bit TE-CX 5/16-6
Bit TE-CX 5/16-12
Bit TE-CX 3/8-6
Bit TE-CX 3/8-12
Bit TE-CX 1/2-6
Bit TE-CX 1/2-12
Bit TE-C+ 5/8-8
Bit TE-C+ 5/8-12
Bit TE-C-S 3/4-8
Bit TE-C-S 3/4-12
Bit TE-C-S 1-10
Bit TE-CX 3/16-4
Bit TE-CX 3/16-6
Bit TE-CX 3/16-8
Bit TE-CX 3/16-12
Bit TE-CX 3/16-16
Bit TE-CX 1/4-4
Bit TE-CX 1/4-6
Bit TE-CX 1/4-8
Bit TE-CX 1/4-12
Bit TE-CX 5/16-6
Bit TE-CX 5/16-12
Bit TE-CX 5/16-18
Bit TE-CX 3/8-6
Bit TE-CX 3/8-12
Bit TE-CX 3/8-18
Bit TE-CX 3/8-24
Bit TE-CX 1/2-6
Bit TE-CX 1/2-12
Bit TE-CX 1/2-18
Bit TE-C+ 9/16-12
Bit TE-C+ 9/16-18
Bit TE-C+ 5/8-12
Bit TE-C+ 5/8-18
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
4"
9-1/2"
2"
4"
9-1/2"
4"
9-1/2"
4"
9-1/2"
4"
9-1/2"
5-1/2"
9-1/2"
5-1/2"
9-1/2"
7-1/2"
2"
4"
5-1/2"
9-1/2"
13-1/4"
2"
4"
5-1/2"
9-1/2"
4"
9-1/2"
15-1/4"
4"
9-1/2"
15-1/4"
21-1/4"
4"
9-1/2"
15-1/4"
9-1/2"
15-1/4"
9-1/2"
15-1/4"
Item No.
Description
00332315
00315225
00332318
00332321
00332324
00315228
00315392
00332327
00332330
00332333
00332336
00332339
00332342
00332345
00028858
00332316
00315226
00332319
00332322
00332325
00315229
00315231
00332328
00332331
00315233
00332334
00332337
00315235
00332340
00332343
00332355
00332358
00332361
Bit TE-CX 3/16-4

Bit TE-CX 3/16-6
Bit TE-CX 3/16-8
Bit TE-CX 3/16-12
Bit TE-CX 3/16-16
Bit TE-CX 1/4-4
Bit TE-CX 1/4-6
Bit TE-CX 1/4-8
Bit TE-CX 1/4-12
Bit TE-CX 5/16-12
Bit TE-CX 5/16-18
Bit TE-CX 3/8-12
Bit TE-CX 3/8-18
Bit TE-CX 3/8-24
Bit TE-C+ 5/8-8
Bit TE-CX 3/16-4
Bit TE-CX 3/16-6
Bit TE-CX 3/16-8
Bit TE-CX 3/16-12
Bit TE-CX 3/16-16
Bit TE-CX 1/4-4
Bit TE-CX 1/4-6
Bit TE-CX 1/4-8
Bit TE-CX 1/4-12
Bit TE-CX 5/16-6
Bit TE-CX 5/16-12
Bit TE-CX 5/16-18
Bit TE-CX 3/8-6
Bit TE-CX 3/8-12
Bit TE-CX 3/8-18
Bit TE-CX 1/2-6
Bit TE-CX 1/2-12
Bit TE-CX 1/2-18
Qty
Effective
Drilling Depth
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
80
70
100
110
125
80
70
100
100
60
100
100
50
100
100
50
80
80
2"
4"
5-1/2"
9-1/2"
13-1/4"
2"
4"
5-1/2"
9-1/2"
9-1/2"
15-1/4"
9-1/2"
15-1/4"
21-1/4"
5-1/2"
2"
4"
5-1/2"
9-1/2"
13-1/4"
2"
4"
5-1/2"
9-1/2"
4"
9-1/2"
15
4"
9-1/2"
15"
4"
9-1/2"
15"
TE-CX Metric Bit Packages

Item No.
Description
Diameter x Length
Qty
Effective
Drilling Depth
00313008
00313031
00313029
00313030
Bit TE-CX 5/12

Bit TE-CX 5/12
Bit TE-CX 5/15
Bit TE-CX 6/17
12
36
12
12
2"
2"
3"
4"
TE-CX/TE-C Variety Bit Packages

00334633
TE-CX Bit Pack Small Diameter Assortment

Includes TE-CX 3/16-6, 1/4-4, 1/4-6, 5/16-6, 3/8-6, 1/2-6
00334634
TE-CX Sample Pack

Includes 2 each of TE-CX 1/4-6, 3/8-6, 1/2-6
00334635
TE-CX Electrician Bit Pack

Includes TE-CX 3/16-6, 1/4-4 (x2), 1/4-6, 3/8-6, 1/2-6
00334636
TE-CX Drywall Acoustical Bit Pack

Includes TE-CX 3/16-6(x2), 1/4-4, 1/4-6 (x2), 3/8-6
00334637
Large Diameter Bit Pack

Includes TE-CX 3/8-12, 1/2-6, 1/2-12;
TE-C+ 5/8-8, TE-C-S 3/4-8
00334638
GC Bit Pack
Includes TE-CX 3/16-6, 1/4-6, 5/16-6, 3/8-6, 1/2-6;
TE-C+ 5/8-8
00334639
Mechanical/Plumbing Pack
Includes TE-CX 3/8-6, 1/2-6(x2); TE-C+ 5/8-8;
TE-C-S 27/32-8, 7/8-10
www.us.hilti.com
2.26
Rotary Hammer Drill
Specialized Bits for Rotary Hammers

Carbide Tipped Unreinforced Masonry Drill Bits (TE-C+ URM)
Effective
Drilling Depth
Item No.
Description
00028061
00028062
00028063
00028065
00028064
Bit TE-C+ 5/8-20 URM ANSI

Bit TE-C+ 5/8-28 URM ANSI
Bit TE-C+ 1-11 URM ANSI
18- 3/8"
26-5/16"
9-7/16"
18-3/8"
23-3/8"
Carbide Tipped Roofing Drill Bits

Item No.
Description
00000583
00000584
00000587
00010268
SDS 7/32 x 6"

SDS 7/32 x 9 1/2"
SDS 7/32 x 11 1/2"
SDS 7/32 x 16 1/2"
Effective
Drilling Depth
4"
7"
9"
14-1/2"
Carbide Tipped Cruciform Bits

Item No.
Description
00220629
00220630
00220631
TE-C+ GB 1 1/8 - 18
TE-C+ GB 1 1/4 - 18
TE-C+ GB 1 1/2 - 18
00262030
00028584
00262031
00262029
Flute 1 1/8-18
Flute 1 1/4-10
Flute 1 1/4-18
Flute 1 1/2-18
Effective
Drilling Depth
15 1/4"
15 1/4"
15 1/4"
TE-C+ BK-TW Thin Wall Core Bits

Item No.
Description
00028844
00028845
00028846
00028847
00028896
00028897
TE-C-BK-TW 1 1/4" Core Bit

TE-C-BK-TW 2" Core Bit
TE-C-BK-TW 3" Core Bit
00028848
TE-C-BK-BS 14-112 Bit Shank (12")

use with 1-1/4" to 1-1/2" core bits
TE-C-BK-BS 2-312 Bit Shank (12")
use with 2" to 3-1/2" core bits
BK-CP 114-112 Centering Pin
used with core bits up to 1-1/2"
BK-CP 2-312 Centering Pin
used with core bits 2" to 3-1/2"
BK-TW 1 1/4" Guide Plate
BK-TW 1 1/2" Guide Plate
BK-TW 2" Guide Plate
BK-TW 2-1/2" Guide Plate
BK-TW 3" Guide Plate
BK-TW 3-1/2" Guide Plate
00028849
00028850
00028851
00028852
00028879
00028880
00028881
00028898
00028899
www.us.hilti.com
KWIK-CON Masonry
Screws see page:
7.41
2.27
Rotary Hammer Drill
Accessories
Square Drive Setting Tools for HVA adhesive anchors
Item No.
Description
00032220
00065277
00065278
00065280
Shank
9/16" Socket
3/4" Socket
15/16" Socket
Automatic Setting Tools for HDI Anchors (for TE15, TE18, TE25 drills)
Item No.
Description
00243751
HSD-M M 3/8"
00243752
HSD-M M 1/2"
Sets Anchor Size
3/8" HDI / HDI-L
TE-C-24 SD 10-3/8" Setting Tool
1/2" HDI / HDI-L
TE-C-24 SD 12-1/2" Setting Tool
KWIK-CON II+ Hex Driver System

Item No.
Description
00235097
KWIK-CON Hex Driver Deluxe Kit
Item No.
Driver System Individual Components
00235100
00235098
00235101
00083313
KWIK-CON 5/16" Hex setter/depth locator

KWIK-CON hex driver
KWIK-CON insert bit holder/depth locator
5/16" Hex Driver - KC II+
00083312
#3 Phillips Driver - KC II+
00083314
T-25 Torxalign Driver
Shown above right
For All THWH without depth setting

For use with all PFH
For use with all 3/16" TFH
00087123
KWIK-CON II+ Matched Tolerance Drill Bits

Dense concrete (2000 psi+)
For 1/4" KWIK-CON II+ Applications in dense concrete (2000 psi+)
Item No.
Description
Bit Marking
00205114
00205115
TKC Large Concrete Bit SDS+ HEX

TKC Large Concrete Bit TM HEX
0.2402
0.2402
For 3/16" KWIK-CON II+ Applications in dense concrete (2000 psi+)

Item No.
Description
Bit Marking
00205118
00205119
TKC Small Concrete Bit SDS+ HEX

TKC Small Concrete Bit TM HEX
0.1902
0.1902
Light weight concrete, block or brick

For 1/4" KWIK-CON II+ Applications in light weight concrete, block or brick
Item No.
Description
Bit Marking
00205116
00205117
TKB Large Block Bit SDS+ HEX

TKB Large Block Bit TM
0.2260
0.2260
For 3/16" KWIK-CON II+ Applications in light weight concrete, block or brick
Item No.
Description
Bit Marking
00205120
00205121
TKB Small Block Bit SDS+ HEX

TKB Small Block Bit TM HEX
0.1752
0.1752
www.us.hilti.com
2.28
TE-C Chisels
TE-C Chisels
The Connection End For Surface And Finish Work
10mm
Advantages
Designed for surfacing and
finish work
Chisel tip geometry optimizes
rate of material removal
Optimum machine to insert tool
weight ratio allows high
performance
TE-C connection end fits all
SDS+ chucks
For use with TE 15-C, TE 25
(with adapter 00030211) and
TE 104
Technical Data
Connection end / shank diameter
10 mm
Chisel / point shank diameter

12 mm
Item No.
Description
Length
Blade Width
TE-C-SM 18
TE-C-SM 25
7"
10"
---
TE-C-FM 18
TE-C-FM 25
7"
10"
9/16"
9/16"
Scaling (Wide flat)

00204738
TE-C-SPM 6/18
00204739
TE-C-SPM 6/25
7"
10"
2 3/8"
2 3/8"
Offset Chisels (Wide flat)

00204735
TE-C SPMK 4/18
00204736
TE-C SPMK 6/18
00204737
TE-C SPMK 8/18
7"
7"
7"
1 1/2"
2 3/8"
3 1/8"
Flexible Chisel
00204740
10"
3 7/8"
Pointed Chisel
00204730
00030219
Flat Chisel
00204731
00030220
For uncontrolled breaks and openings in concrete
For controlled breaks in concrete
For scaling
For scraping applications and tile removal
TE-C-BSPM 10/25
For removing linoleum,

vinyl tile and coatings
Channel Chisel
00030221
TE-C-KM 2/25
10"
3/4"
For gouging channels in grout filled block
Carbide Mortar Chisel

00204741
TE-C-FGM 25
10"
1 1/4"
For recessing mortar
Curved Mortar / Joint Chisel

00204742
TE-C-MM 0.8/18
00204743
TE-C-MM 1.2/18
7"
7"
5/16"
15/32"
For mortar removal
www.us.hilti.com
Tool Ordering information:
TE 104 see page 2.42
TE 15-C see page 2.20
TE 25 see page 2.22
2.29
Dust Removal System
Dust Removal Systems
Technical Data TE 5 DRS

Power input
Permits Drilling In Clean Room Environments
Max 60 W
Suction capacity
17.7 cfm
TE 5 DRS Advantages
Max bit length
Modular design allows for easy attachment and removal of dust

removal system
Tool length remains the same with dust removal module installed
Light weight, compact design, convenient to use
Self contained design: No vacuum or additional hoses required all
functions integrated into DRS module
Dust Removal System driven by TE 5 motor
Reusable dust filter
4" to 6" standard, up to 8" using tall

suction tube assembly (sold separately)
For use with TE-C drill bits


TE 5 Dust Removal System Module

Complete with fitted dust container, dust container cover and extraction head.
Maximum drilling capacity 11/16".
Item No.
Description
00201390
00201397
00258106
00258107
Dust Removal Module in expanded plastic Hilti case*

Dust Removal Module in cardboard box*
Suction Tube Assembly-short (not shown)
Suction Tube Assembly-tall (not shown)
For use with 8" long bits
* TE 5 drill sold separately
Technical Data TE-DRS-S

Maximum movement
For use with Hilti tools TE 2, 15, 18-M, 25, 35, 55
5 1/2"
TE-DRS-S Advantages
Removes 80% or more dust produced during drilling operations
Open suction head allows unobstructed view of centering and drilling
progress
Protects operator and surroundings from most airborne dust
generated during drilling operations
Quick release for easy attachment and
removal
Integrated depth gauge for accurate hole
depth
DRS adapter fits most industrial vacuums
One year limited warranty
Description
00340602
TE-DRS-S Assembly
1 lb
Drill bit diameter range

3/16" to 1-1/2"
Drill bit lengths

2" to 15-1/2"
Core bit diameter range

1" to 3-1/4"
Nominal power of
industrial vacuum
800 W or greater
Connector for industrial vacuum

1-5/16" minimum taper
DRS connector taper

1:20
TE-DRS-S Assembly
Item No.
Weight
Vacuum hose adapter not included
TE-DRS-S Replacement Parts

Item No.
Description
00340603
TE-DRS-S Spare Parts Kit
Includes 1 ring, 2 stops and 1 hose connection
00340604
TE-DRS-S Connection Hose (approx. 3-1/2 ft)
00340605
TE-DRS-S Dust Removal System HeadSmall
For use with 3/16" to 1" diameter drill bits
00340606
TE-DRS-S Dust Removal System HeadLarge
For use with 1" to 3-1/4" diameter drill bits
00072920
www.us.hilti.com
TE-DRS-S Vacuum Hose Adapter
2.25
TE 2 Rotary Hammer Drill
see page 2.12
TE 15 Rotary Hammer Drill
see page 2.19
TE 18-M Rotary Hammer
Drill see page 2.21
2.30
The Hilti TE 35 Medium Mass Combihammer

A Genuine Combihammer For Balanced Drilling and Chiseling
TE-T
Power input
830 W
Voltage
115 V
Frequency
5060 Hz

03720 blows/min
Speed under load

0620 rpm

2.8 ft-lb
Weight
10.9 lb
Dimensions (LxHxW)
18.1" x 8.6" x 3.9"
3/8"
CONCRETE
1/2"
3-9/16"
1"
Steel: Up to 1/2"
Hole Saw: up to 5"
Advantages
Accessory Program
Carbide tipped drill bits TE-T

1/4" to 1-1/4" diameter
Carbide tipped core bits up to
3-9/16"
Chisels: pointed, flat, channel,
scaling and mortar chisels
Designed for a wide range of applications

Lightweight yet powerful
Electronic speed switch operable when working in any direction
Infinite speed regulation ideal for accurate hole starting
Padded rubber grip to dampen vibration. Grip opening designed with
plenty of room for operator's glove
Supply cord positioned for convenience and operator comfort
R e p a i r
Item No.
Description
00312472
TE 35 Deluxe
Includes impact resistant Hilti case, side handle, dust shield,
cleaning cloth, spray lubricant, and operating instructions
P r o g r a m
00312476
TE 35 Deluxe grounded
Includes impact resistant Hilti case, side handle, dust shield,
cleaning cloth, spray lubricant, and operating instructions
www.us.hilti.com
2.33
Chisels see page:
2.34
2.30
2.31
Common Applications For The TE 35

Powerful:
Penetrations and through holes for
electrical and plumbing installations
Economical:
Serial drilling for rebar doweling
Comfortable:
Drilling holes to fasten beams and
brackets
Handy:
Enlarging openings for pipe runs
Precise:
Gouging channels for conduits
Quick:
Coring recesses for electrical installations
Versatile:
Drilling steel and wood
www.us.hilti.com
2.32
TE 35 Combihammer Drill Bits
TE-T & TE-TX Carbide Tipped Drill Bits
NEW!
Ideal For A Wide Range Of Drilling And Chiseling Applications

14mm
Advantages
Wide drilling range 1/4" to
3-9/16"
Quicker dust removal resulting
in higher bit performance
Optimal power transmission
produced with strong TE-T
connection end
For use with Hilti TE 35 and combihammers with SDS-top chuck

TE-T and TE-TX Carbide Tipped and Helical Drill Bits
TE-T Carbide Tipped and Helical Drill Bits (TE-T metric)
Item No.
Description
Effective
Drilling Depth
00338410
00338411
00335915
00335916
00335917
00338412
00333471
00333472
00333473
00332981
00333474
00333475
00331901
00333476
00333478
00372095
00340720
00340721
00340722
00340723
00340724
00340725
00340726
00340727
00340705
00340729
00340732
00340731
00340732
Bit TE-TX 1/4-9

Bit TE-TX 5/16-15
Bit TE-TX 3/8-9
Bit TE-TX 3/8-15
Bit TE-TX 3/8-21
Bit TE-TX 7/16-9
Bit TE-T 1/2-9
Bit TE-T 1/2-13
Bit TE-T 1/2-21
Bit TE-T 9/16-13
Bit TE-T 9/16-21
Bit TE-T 5/8-9
Bit TE-T 5/8-13
Bit TE-T 5/8-21
Bit TE-T 11/16-21
Bit TE-TX 11/16-13
Bit TE-TX 11/16-21
Bit TE-TX 3/4-13
Bit TE-TX 3/4-21
Bit TE-TX 13/16-21
Bit TE-TX 27/32-13
Bit TE-TX 7/8-13
Bit TE-TX 7/8-21
Bit TE-TX 1-13
Bit TE-TX 1-21
Bit TE-TX 1 1/8-15
Bit TE-TX 1 1/8-23
Bit TE-TX 1 1/4-15
Bit TE-TX 1 1/4-23
4"
10"
4"
10"
16"
4"
4"
7-3/4"
15-3/4"
7-3/4"
16-3/4"
4"
7-3/4"
15-3/4"
16"
7-3/4"
15-3/4"
7-3/4"
15-3/4"
15-3/4"
7-3/4"
7-3/4"
15-3/4"
7-3/4"
15-3/4"
9-1/2"
17-1/4"
9-1/2"
17-1/4"
00340467
TE-TX/TE-T Small Assortment
00340468
TE-TX/TE-T Sample Pack
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
Includes 2 each TE-TX 1/4-9, 3/8-9 and TE-T 1/2-9

Includes TE-TX 1/4-9, 3/8-9; TE-T 1/2-9, 5/8-9, 3/4-13, 7/8-13, 1-13;
TE-T pointed chisel (10-1/2") and 5/8" flat chisel (10-1/2")
Item No.
Description
Diameter,mm x Length,cm
00333740
00333741
00333742
00333743
00333744
00333745
00333746
00333747
00333748
00333749
00333750
00333751
00333752
Bit TE-TX 12/23

Bit TE-TX 12/33
Bit TE-TX 12/53
Bit TE-TX 12/65
Bit TE-TX 14/23
Bit TE-TX 14/33
Bit TE-TX 14/53
Bit TE-TX 15/23
Bit TE-TX 15/33
Bit TE-TX 15/53
Bit TE-TX 12/23
Bit TE-TX 12/33
Bit TE-TX 12/53
00339006
00338997
00339005
00339009
00339010
00339013
00339014
Bit TE-TX 18/32

Bit TE-TX 18/52
Bit TE-TX 24/32
Bit TE-TX 28/32
Bit TE-TX 25/52
Bit TE-TX 32/37
Bit TE-TX 32/57
Effective
Drilling Depth
5-9/10"
7-7/8"
15-3/4"
21-5/8"
5-9/10"
7-7/8"
15-3/4"
21-5/8"
7-7/8"
15-3/4"
5-9/10"
7-7/8"
15-3/4"
NEW
NEW
NEW
NEW
NEW
NEW
NEW
1-7/8"
15-3/4"
7-7/8"
7-7/8"
15-3/4"
9-27/32"
17-11/16"

www.us.hilti.com
2.33
TE-T Chisels & Accessories

TE-T Carbide Tipped Cruciform Bits

Item No.
Description
00308917
Bit TE-T-GB 1 1/2-23
Effective Drilling Depth
17-5/8"
TE-T Carbide Tipped Single Piece Core Bits

Item No.
Description
00314251
00314252
00314253
00314254
Bit TE-T-BK
Bit TE-T-BK
Bit TE-T-BK
Bit TE-T-BK
Effective Drilling Depth
2-10"
2 5/8-10"
3 1/4-10"
3 9/16-10"
6"
6"
6"
6"
TE-T Chisel Program

Pointed Chisels
Item No.
Description
00315409
00307042
00315410
00312425
TE-T-SM 27
Chisel PTD TE-T SM 27 (3 Pack)
TE-T-SM 35
Chisel PTD TE-T SM 35 (3 Pack)
Total Length
Blade Width
10-1/2"
10-1/2"
13-3/4"
13-3/4"
-----
Total Length
Blade Width
10-1/2"
10-1/2"
13-3/4"
13-3/4"
5/8"
5/8"
5/8"
5/8"
Total Length
Blade Width
9-3/4"
9-3/4"
9-3/4"
1-1/2"
2-1/4"
3"
Total Length
Blade Width
9-3/4"
2-1/4"
Flat Chisels
Item No.
Description
00315411
00307044
00315412
00312426
TE-T-FM 27
Chisel FLT TE-T FM 27 (3 Pack)
TE-T-FM 35
Chisel FLT TE-T FM 35 (3 Pack)
Scaling Chisels (Wide-Flat)

Item No.
Description
00307045
00307046
00307048
TE-T-SPM 4/25
TE-T-SPM 6/25
TE-T-SPM 8/25
For scaling and cutting asphalt
Offset Chisel (Wide-Flat)

Item No.
Description
00307047
TE-T-SPMK 6/25
Channel Chisel
Item No.
Description
00307049
TE-T-KM 2.5/27
Total Length
Blade Width
10-1/2"
1"
Total Length
Blade Width
11"
1"
Mortar Chisel
Item No.
Description
00307050
TE-T-FGM 28
Bushing Tool
Item No.
Description
00370606
TE-T SKHM Bushing Tool
Total Length
Blade Width
10"
1-1/2" x 1-1/2"
Chucks
Item No.
Description
00316076
TE-T Chuck
For use with drill bits and chisels with TE-T connection end
00314481
1/2" Keyless Chuck (For use with TE 35 only)

For use with smooth shank bits up to 1/2" diameter; rotary drilling only
For smoothing rough concrete surfaces and

roughing up smooth concrete surfaces
Drive Shaft & Sockets

Item No.
Description
00332169
Square Drive Shaft TE-T-SD 3/4"
3/4" Drive Sockets

Item No.
Description
00065279
00065281
00065282
00065283
00065284
3/4" Diameter
1-5/16" Diameter
1-1/8" Diameter
1-7/16" Diameter
1-1/2" Diameter
Hilti Case Replenishment Items

Item No.
Description
00203086
00308976
00009354
00060503
Hilti Tool Grease

Hilti Spray Lubricant
Cleaning Cloth
Blow-out Bulb
www.us.hilti.com
For use with Hilti Combihammer:
TE 35 Medium Mass
Combihammer see page:
2.31
2.34
Hilti TE 55 Combihammer
The Standard In Comfort, Performance, And Long Life
TE-Y
(SDS Max)
Power input
900 W
Voltage
115 V
Frequency
5060 Hz

02630 blows/min
Speed loaded
1st Speed: 0230 rpm
2nd Speed: 0480 rpm

100%: 4.4 ft-lb
50%: 2.2 ft-lb
Machine weight
13.0 lb
Dimensions (LxWxH)
17.3" x 3.5" x 9.2"
Drilling performance with 3/4"

bit
Up to 4.3 in3/min
Chiseling performance
Up to 18.3 in3/min
1/2"
CONCRETE
5/8"
3-9/16"
1"
Steel: Up to 1/2"
Advantages
Accessory Program
Lower vibration levels as a result of new control elements

Two-speed gearing for improved performance in smaller diameter
ranges and increased comfort
Control electronics for consistent load to tool allowing dramatic tool life
improvements
Uses carbide tipped masonry bits from 1/2" to 1-1/4", core bits from
1-1/2" to 3-9/16", and cruciform bits from 1-1/2" to 2"
Hammer drilling and chipping modes
Service indicator light advises user to provide maintenance to reduce
down time during critical periods
Two hammer settings: 100% power for tough jobs,
50% power for added control
Double-insulated construction
TE-Y Carbide-tipped Helical

Drill Bits for concrete,
brick and masonry from 1/2" to
1-1/4"
TE-Y-GB Cruciform Bits from
1-1/2" to 2"
TE-Y-BK Core Bits from 1-1/2"
to 3-9/16" diameter
TE-Y Chisels: pointed, flat,
channel, scaling, mortar,
bushing tools
in a variety of lengths and
ground rod adapters
Adapter available to allow use
with TE-C+ Bits
Steel bits with use of 1/2"
Keyed Chuck and Spindle
Just in
the TE 56xi
See Page s.
for detail
R e p a i r
P r o g r a m
Item No.
Description
00258481
TE 55 DLX double-insulated 115 V

Comes with 13 ft (4 m) supply cord, impact resistant Hilti
case, Hilti grease, cleaning cloth and operating instructions
00258474
TE 55 DLX double-insulated 220 V

case, Hilti grease, cleaning clothand operating instructions
www.us.hilti.com
00258482
TE 55 DLX grounded 115 V

case, Hilti grease, cleaning clothand operating instructions
2.38
Item No.
Description
For Use With
00256897
Adapter TE-Y to TE-C
TEC/SDS+ Bits
Chisels see page:
2.40
2.30
2.35
Hilti TE 76 & TE 76-ATC Combihammer

The complete program that makes a big impact
TE-Y
(SDS Max)
Technical Data
Power input
1300 W
Voltage
115 V
Frequency
5060 Hz

Power setting II: 02770 bpm
Power setting I: 01965 bpm
Speed loaded
Power setting II: 0282 bpm*
Power setting I: 0200 bpm*
Advantages
More benefits to the user
Active Torque Control for added operator

protection (TE 76-ATC only)
Better balance
Padded rear grip and side handle
Grippable chuck for bushing applications
Constant on for chipping applications
Service indicator light advises user to provide
maintenance to reduce down time during critical
periods
Power reduction
Optimized for operator comfort
20% higher performance than its predecessor
30% less vibration
With the TE 76-ATC, Hilti has set new standards in

the high-performance combihammer class:
More performance for higher work productivity
More quality for longer life expectancy
More protection for the operator
More comfort to save effort
More versatility for a wider range of applications
Wider range of application

Hammer drilling in concrete, masonry and
natural stone from 1/2" to 6" diameter
Chiselling in concrete, masonry and natural stone
Setting anchors
Drilling without hammering using keyed or
keyless chuck in wood: 1/2" to 1-1/4" diameter
in metal: 1/2" to 3/4" diameter
Mixing repair mortar using 3" to 6" diameter
mixing paddles
Hilti TE 76-ATC Combihammer with slip clutch and ATC

Item No.
Description
00334239
TE 76-ATC Grounded 115 V

Equipped with 13 ft supply cord, impact resistant Hilti case
with integrated selector chart, Hilti grease, cleaning cloth,
Power setting II: 6.1 ft-lb

Power setting I: 3.1 ft-lb
Tool weight
TE 76-ATC: 17.4 lb
TE 76: 15.4 lb
Dimensions (LxWxH)
TE 76-ATC: 20"x 4.5" x 11.3"
TE 76: 19.6" x 4.5" x 10.3"
Typical drilling performance in

medium-hard concrete
Dia. 3/4": Up to 360 mm/min
Dia. 1": Up to 290 mm/min
Dia. 1-1/4" 180 mm/min
Typical chiseling performance

into medium-hard concrete
up to 575 cm3/min
Minimum distance of hole

drilled from wall
1-1/2"
* bpm = blows per minute
1/2"
CONCRETE
7/8"
6"
1-3/8"
Wood: Up to 5" Hole Saw

Wood: Up to 1-1/4" Auger
Steel: Up to 1/2"
Hilti TE 76 Combihammer with slip clutch

Item No.
Description
00334225
TE 76 Grounded 115 V
Equipped with 13 ft supply cord, impact resistant Hilti case
with integrated selector chart, Hilti grease, cleaning cloth,
Accessories
R e p a i r
Item No.
Description
00334133
Depth gauge
P r o g r a m
For use in setting the desired drilling depth

Case Study #1703* Construction Supervisor
ADDED
VALUE
$48,003 project labor savings using Hilti TE 76

Combihammer to drill 15,000 holes versus using Hilti
TE 55 Combihammer.
* For complete details, contact Hilti. Actual results may vary.
www.us.hilti.com
2.38
2.36
Hilti TE 76-ATC: Top Performance And Versatility For The Professional User
Quick:
holes using TE-Y hammer drill bits
(1/2" to 1-9/16" diameter)
Installing anchors such as Hilti HVA
Adhesive Anchor using specials
setting tools.
Powerful:
Drilling through-holes using
TE-Y-GB breach bits (1-1/2" to
3-1/8" diameter)
Working surfaces with bushing tool.
Efficient:
Cutting sockets using TE-Y-BK
percussion core bits (1-3/4" to 6"
diameter)
Working with shaped chisels to
gouge channels for electrical
conduit.
Effective:
Chiseling with power and precision
Drilling into wood and metal using
chuck holder and quick release
chuck.
www.us.hilti.com
2.37
TE-Y & TE-YX Carbide Tipped Drill Bits

Power At It's Peak
NEW!
18mm
Advantages
High dimensional
accuracy throughout life
of the drill bit
Easy hole starting
Double flute helix
produces rapid removal
of dust and fragments
Two carbide pins for
faster, smoother drilling
Minimal wear of
connection end and
chuck
Coated carbide extends
life of bit
For use with Hilti TE 54, 55, 72, 74, 75, 76, 76-ATC and combihammers with SDS-max chuck
Carbide Tipped TE-Y and TE-YX Drill Bits (Metric)
Carbide Tipped TE-Y and TE-YX Drill Bits

Item No.
Description
Effective
Drilling Depth
00220632
00220633
00220634
00220635
00220636
00220637
00220638
00220639
00220640
00220641
00220642
00372094
00340694
00340695
00340696
00340697
00340698
00340699
00340700
00340701
00340702
00340703
00340704
00340705
00340706
00340707
00340708
00340709
00340710
00340711
00340712
00340713
00340714
00340715
00340716
00340717
00340718
00339040
TE-Y 1/2-13
TE-Y 1/2-21
TE-Y 9/16-13
TE-Y 9/16-21
TE-Y 5/8-13
TE-Y 5/8-21
TE-Y 5/8-36
TE-Y 11/16-21
TE-Y 3/4-13
TE-Y 3/4-21
TE-Y 3/4-36
Bit TE-YX 11/16-13
Bit TE-YX 11/16-21
Bit TE-YX 3/4-13
Bit TE-YX 3/4-21
Bit TE-YX 3/4-36
Bit TE-YX 13/16-21
Bit TE-YX 27/32-13
Bit TE-YX 27/32-21
Bit TE-YX 7/8-13
Bit TE-YX 7/8-21
Bit TE-YX 7/8-36
Bit TE-YX 1-13
Bit TE-YX 1-21
Bit TE-YX 1-36
Bit TE-YX 1 1/16-21
Bit TE-YX 1 1/8-15
Bit TE-YX 1 1/8-23
Bit TE-YX 1 1/8-36
Bit TE-YX 1 1/4-15
Bit TE-YX 1 1/4-23
Bit TE-YX 1 1/4-36
Bit TE-YX 1 5/16-23
Bit TE-YX 1 3/8-23
Bit TE-YX 1 3/8-36
Bit TE-YX 1 1/2-15
Bit TE-YX 1 1/2-23
Bit TE-YX 1 9/16-23
7"
16"
7"
16"
7"
16"
30-1/2"
16"
7"
16"
30-1/2"
7"
16"
7"
16"
30-1/2"
16"
7"
16"
7"
16"
30-1/2"
7"
16"
30-1/2"
16"
8-3/4"
17-5/8"
30-1/2"
8-3/4"
17-5/8"
30-1/2"
17-5/8"
17-5/8"
30-1/2"
8-3/4"
17-5/8"
17-5/8"
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
Item No.
Description
Diameter,mm x length,cm
00333753
00333754
00333755
00333756
00333757
00333758
00333759
00333760
00333761
00339015
00339016
00339024
00339025
00339030
00339031
00339031
00339034
00339035
00339038
00339039
Bit TE-YX 12/35

Bit TE-YX 12/55
Bit TE-YX 12/67
Bit TE-YX 14/35
Bit TE-YX 14/55
Bit TE-YX 15/35
Bit TE-YX 15/55
Bit TE-YX 16/35
Bit TE-YX 16/55
Bit TE-YX 18/32
Bit TE-YX 18/52
Bit TE-YX 24/32
Bit TE-YX 24/52
Bit TE-YX 28/32
Bit TE-YX 28/52
Bit TE-YX 28/52
Bit TE-YX 32/37
Bit TE-YX 32/57
Bit TE-YX 37/57
Bit TE-YX 37/92
Effective
Drilling Depth
7-7/8"
15-3/4"
21-5/8"
7-7/8"
15-3/4"
7-7/8"
15-3/4"
7-7/8"
15-3/4"
6-1/2"
14-1/2"
6-1/2"
14-1/2"
6-1/2"
14-1/2"
14-1/2"
9-1/2"
17-1/4"
17-1/4"
30-1/2"
TE-YX Bit Packages

Item No.
Description
00220719
Electricians Package
Includes 1/2-13(2), 3/4-13, 1-13
Plumbers Package
Includes 1/2-13, 5/8-13, 3/4-13, 7/8-13
GC/Industrial Package
Includes 1/2-13, 5/8-13, 3/4-13, 1-13
Long Bit Package
Includes 1-23, 1 1/4-23, 1 1/2-23
Variety Package (Bits and Chisels)
Incl. TE-Y 1/2-13, TE-Y 3/4-13, 19" Ptd Chisel, 19" Flt Chisel
00220721
00220720
00220802
00220803

www.us.hilti.com
2.38
TE-Y Drill Bits & Accessories
TE-Y Carbide Tipped Core Bits & Cruciform Bits

Core Bit Advantages
Core bit with rounded base
produces up to 20% higher
drilling performance and up to
20% longer life expectancy
resulting in reduced labor and
tooling costs
New pilot bit retention with
secure locking prevents pilot bit
loss
Optimized Vario flute minimizes
catching and minimizes
friction at hole wall
Carbide Tipped Single Piece Core Bits

Item No.
Description
Effective
Drilling Depth
00307053
00307054
00307055
00307056
00307059
00307060
00307061
00307062
00307063
00307064
00307065
00307066
00307067
TE-Y BK 1 3/4-12
TE-Y BK 1 3/4-22
TE-Y BK 2-12
TE-Y BK 2-22
TE-Y BK 2 5/8-12
TE-Y BK 2 5/8-22
TE-Y BK 3 1/4-12
TE-Y BK 3 1/4-22
TE-Y BK 3 9/16-12
TE-Y BK 3 9/16-22
TE-Y BK 4-17
TE-Y BK 5-17
TE-Y BK 6-17
00262750
00262751
00006135
Centering Bit
Rubber Retaining Ring
Centering Bit Retaining Pin
7-1/2"
18"
7-1/2"
18"
7-1/2"
18"
7-1/2"
18"
7-1/2"
18"
12-1/2"
12-1/2"
12-1/2"
Carbide Tipped Cruciform Bits

Item No.
Description (diameter x lengthinches)
00220609
00220611
00028903
00028366
00028367
Bit TE-Y GB 1 1/2-23

Bit TE-Y GB 2-23
00060748
00262019
00262021
00262023
00262026
00262028
Flute GB 1 1/2-17
Flute GB 1 1/2-23
Flute GB 1 3/4-23
Flute GB 2-23
Flute GB 2 1/2-23
Flute GB 3 1/8-23
Effective
Drilling Depth
17-5/8"
17-5/8"
17-5/8"
17-5/8"
17-5/8"
www.us.hilti.com
TE 55 Combihammer
see page:
2.35
TTE 76 / TE 76-ATC
2.36
2.39
TE-Y Accessories
TE-Y Chisels
ADDED
VALUE
Chisels With A Powerful Punch
Case Study #504113*

Project Manager
18mm
$8,000 project labor

savings using Hilti
TE 55 Combihammer
and flex chisel to
remove adhesive from
concrete versus using
hand scrapers.
Hilti Chisel Advantages

Induction-hardened composite chisels
(made from two materials)
Precise hardening of each section extends life of chisel
* For complete details, contact

Hilti. Actual results may vary.
TE-Y Chisels
Pointed Chisels
Item No.
Description
00002708
00204333
00336406
00204334
00336409
00204335
CHSL PTD TE-Y KSM 28

CHSL PTD TE-Y KSM 36 (4 Pack)
Total
Length
11"
14"
14"
19"
19"
27"
Flat Chisels
Item No.
Description
00002709
00204336
00336407
00204337
00336408
00204338
CHSL FLT TE-Y KFM 28

CHSL FLT TE-Y KFM 36 (4 Pack)
Scaling (Wide Flat)

Item No.
Description
00002710
00259558
00259559
00254793
00254794
CHSL Wide Flat TE-Y-KSPM4/28

CHSL Wide Flat TE-Y-KSPM 5/36
Total
Length
Blade
Width
11"
14"
14"
19"
19"
27"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
Total
Length
Blade
Width
11"
11"
14"
14"
19"
1-1/2"
2-3/4"
1-1/2"
4-1/2"
4-1/2"
Channel Chisels
Item No.
Description
00259560
00259562
00259563
CHSL Hollow CHNL TE-Y KM 2.8/28

CHSL CHNL TE-Y KM 3.6/28
CHSL Flanged CHNL TE-Y KM 3.6/28
Shown
Total
Length
11"
11"
11"
Blade
Width
1"
1-1/2"
1-1/2"
For gouging channels in concrete
For cutting channels in hollow block
Clay Spade
Item No.
Description
96204592
TE-Y CLAY SPADE
Total
Length
17"
Blade
Width
4-1/2"
For breaking compacted base such as clay or dirt
Flexible Chisel
Item No.
Description
00252462
Flex TE-Y BSPM 800
Total
Length
25-1/2"
Blade
Width
5-7/8"
For removing linoleum, vinyl tile, coatings and concrete form cleaning
Mortar Chisel
Item No.
Description
00001929
CHSL MTR TE-Y FGM 6.5/28
Total
Length
11"
Blade
Width
1-5/16"
Carbide Bushing Tool

Item No.
00062893
Description
Bushing Tool TE-Y SKHM
Total
Length
10"
TE-Y Chisel Packages

Item No.
Description
00220722
Chisel Package
Incl. 14" Ptd Chisel, 19" Ptd Chisel, 14" Flt Chisel, 19" Flt Chisel
Variety Package (Chisels and Bits)
Incl. 19" Ptd Chisel, 19" Flt Chisel, TE-Y 1/2-13, TE-Y 3/4-13
00220803
Blade
Width
1-1/2"x 1-1/2"

www.us.hilti.com
2.40
TE-Y Accessories
Chucks & Adapters
Item No.
Description
Shown
For Use With
00256897
Adapter TE-Y to TE-C
TEC/SDS+ Bits
00060208
Keyless Chuck
Wood/Steel Bits
00240704
1/2" Keyed Chuck, key included
00263359
TE-Y-BFH Spindle
Wood/Steel Bits
For rotation only drilling using TE 52, TE 55, TE 72, TE 74, TE 75,
TE 76, TE 76-ATC and TE 92. Requires Keyless Chuck (Item No. 00060208)
or Keyed chuck (Item No. 00240704).
TE-Y-K Bit Extension

Advantages
No special order bits required
Can be used with any TE-Y-K accessory (bits, cruciform, core bits)
Fits into drill just like a drill bit
Extension Shank TE-Y
Item No.
Description
00030789
TE-Y Extension Assembly
Adapter TE-Y-K
Includes TE-Y 850 Extension Shank and TE-Y-K adapter

For use with TE-Y drill bits 1-3/8" diameter and up
Extends effective drilling depth 28"
00001952
Extension Shank TE-Y 350
00001953
00001954
00062116
Adapter TE-Y-K
Overall length 13-3/4"

Overall length 23-5/8"
Overall length 33"
Ground Rod Adapters

Item No.
Description
For Use With
00220700
00220701
00220702
TE-Y-RD 1/2"
TE-Y-RD 5/8"
TE-Y-RD 3/4"
TE 52, 54, 55, 72, 74, 75, 76, 92, 505, 705
TE 52, 54, 55, 72, 74, 75, 76, 92, 505, 705
TE 52, 54, 55, 72, 74, 75, 76, 92, 505, 705
Drive Shafts & Sockets
Rebar Adapters
Item No.
Item No.
Description
00032221
Square Drive Shaft TE-Y-SD 3/4"
00020693
Square Drive Shaft TE-Y-SD 1"
3/4" Drive Sockets
www.us.hilti.com
TE 55 Combihammer
see page:
2.35
Item No.
Description
00065279
00065281
00065282
00065283
00065284
1" Drive Sockets
3/4" Diameter
1-5/16" Diameter
1-1/8" Diameter
1-7/16" Diameter
1-1/2" Diameter
Item No.
Description
00065285
1-7/8" Diameter
00220695
00220696
00220697
00220698
00220699
Description
TE-Y Rebar Adapter # 4

TE-Y Rebar Adapter # 5
TE-Y Rebar Adapter # 6*
*To be used in TE 75, TE 76, TE 76-ATC or TE 92 only.

Item No.
Description
00203086
00308976
00009354
00060503
Hilti Tool Grease

Hilti Spray Lubricant
Cleaning Cloth
Blow-out Bulb
TTE 76 / TE 76-ATC
2.36
2.41
Hilti TE 104 Chipping Hammer

Hiltis Lightest Chipping Hammer Makes the Job Go Faster
TE-C (SDS)

Power input
550 W
Voltage
115 V
Frequency
5060 Hz

03800 blows/min

1.62 ft-lb
Machine weight*
7.72 lb
Dimensions (LxWxH)
Advantages
Accessory Program
Compact, lightweight design for working overhead or in tight spaces

Perfect for light duty chipping
Variety of insert tools available including pointed, flexible, mortar
removing, flat, channel and scaling chisels
Unique needle adapter for scaling applications
Chisels: Pointed, flat, channel,

scaling, mortar, bushing tools in
a variety of lengths
Needle adapter available for
scaling applications
14" x 3" x 7-1/2"
Chiseling performance
Up to 12.2 in3/min
*Weight without supply cord.
R e p a i r
P r o g r a m
Item No.
00223497
Description
TE 104 DLX 115 V

Includes supply cord, Hilti tool grease, instruction manual

Item No.
Description
00203086
00009354
Hilti Tool Grease

Cleaning Cloth
www.us.hilti.com
Chisels see page:
2.43
Needle Adapter see page:
2.43
2.42
TE-C Chisels
TE-C Chisels
A Connection End For Surfacing And Finish Work
10mm
10mm
Advantages
Designed for surfacing and finish work

Chisel tip geometry optimizes rate of chiseling
Optimum machine-to-insert tool weight ratio allow high performance
TE-C connection end fits all SDS+ chucks
For use with:
-TE 15-C
-TE 25 (with chisel adapter 00030211)
-TE 104
Technical Data
Connection end / shank diameter
10 mm
Chisel / point shank diameter

12 mm
Item No.
Description
Length
Blade Width
7"
10"
---
7"
10"
9/16"
9/16"
7"
10"
2-3/8"
2-3/8"
Wide Flat Offset Chisels

00204735
TE-C SPMK 4/18
00204736
TE-C SPMK 6/18
00204737
TE-C SPMK 8/18
7"
7"
7"
1-1/2"
2-3/8"
3-1/8"
Flexible Chisel
00204740
10"
3-7/8"
Pointed Chisel
00204730
TE-C SM 18
00030219
TE-C SM 25
Flat Chisel
00204731
TE-C FM 18
00030220
TE-C FM 25
Wide Flat Chisels (Scaling)
00204738
TE-C SPM 6/18
00204739
TE-C SPM 6/25
TE-C BSPM 10/25
For removing linoleum, vinyl tile,

coatings and concrete form cleaning
Channel Chisel
00030221
TE-C KM 2/25
10"
3/4"
Carbide Mortar Chisel

00204741
TE-C FGM 25
10"
1-1/4"
Curved Mortar / Joint Chisel

00204742
TE-C MM 0.8/18
00204743
TE-C MM 1.2/18
Needle Adapter
7"
7"
Item No.
Description
00232800
00223428
00232860
Needle Adapter
Spare Needle (single)
Spare Needles Assembly
5/16"
15/32"
For mortar removal
To clean off rust, slag, or barnacles from steel
www.us.hilti.com
2.43
Hilti TE 505 Light Weight Chipping Hammer

Light In Weight, Strong In Power
TE-Y
(SDS Max)

Power input
900 W
Voltage
115 V
Frequency
5060Hz

1860 blows/min (low)
2630 blows/min (high)

1.92 ft-lb (low)
3.84 ft-lb (high)
Weight*
12.13 lb
Dimensions (LxWxH)
17.3" x 3.5" x 9.1"
Chiseling performance in 4000 psi

concrete with light duty chisel
Features
Advantages
Padded rear grip for added

operator comfort
Rocker switch with lock-on
button
D-style padded side handle
Hammering power regulation to

suit the application
Chisel position adjusts to 12
positions for easy access in
tight places
Modular design for easy service
and repair
Permanently lubricated
UL Listed double insulation

construction
Support
Chisels interchangeable with
combihammers
Service indicator light advises
user when to provide
maintenance
up to 22 in3/min
*Weight with side handle and

without supply cord
R e p a i r
P r o g r a m
Item No.
Description
00314403
TE 505 Deluxe 115 V

Includes 13 ft supply cord, Hilti tool grease, cleaning cloth,
operating instructions and safety precautions in impact
resistant Hilti case
www.us.hilti.com
Chisles see page:
2.46
2.44
Hilti TE 705 Versatile Breaker

More Power, Less Vibration, TE-Y Connection End
Outperforms All Other Light-Duty Breakers in its Class
TE-Y
(SDS Max)

Power input
1030 W
Voltage
115 V (220 V available)
Frequency
5060Hz

1890 blows/min (low)
2670 blows/min (high)

3.2 ft-lb (low)
6.3 ft-lb (high)
Weight
15.25 lb
Dimensions (LxWxH)
Advantages
20.5" x 4.7" x 8.7"
Chiseling performance in 4000psi

concrete with SM36 chisel
removal of up to 37 in3/min
R e p a i r
Exceptional design for user

comfort and lower vibration
20% more power than the
TP400
Lightweight design only 15.25 lb
Connection end identical to that
of TE 55 and TE 75
Uses the same proven motor as

the TE 75
Two-level hammering power
regulation for adjusting to base
material
Active no-load hammering
cut-out so the tool does not
have to work when idling
Service indicator light advises
user when to provide
maintenance
Utilizes extensive Hilti chisel

program designed for many
uses
Designed for easy repair with
easy access to wear parts
Support
P r o g r a m
Item No.
Description
00313263
TE 705 Deluxe 115 V

00313261
TE 705 Deluxe 220 V

www.us.hilti.com
Chisels see page:
2.46
2.45
TE-Y Chisels
TE-Y Chisels
Chisels With A Powerful Punch
18mm
Advantages
Optimized design with stepped
shank for maximum power
transmission
High rate of removal and
accurate guidance
Durable, long life expectancy
Induction hardened composite
chisels made from two materials
Precise hardening of each
section extends life of chisel
TE-Y Chisels
Pointed Chisels
Total
Length
Item No.
Description
00002708
00204333
00336406
00204334
00336409
00204335

11"
14"
14"
19"
19"
27"
Flat Chisels
Item No.
Description
00002709
00204336
00336407
00204337
00336408
00204338

Wide Flat Chisels (Scaling)

Item No.
Description
00002710
00259558
00259559
00254793
00254794

Total
Length
Blade
Width
11"
14"
14"
19"
19"
27"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
Total
Length
Blade
Width
11"
11"
14"
14"
19"
Channel Chisels
1-1/2"
2-3/4"
1-1/2"
4-1/2"
4-1/2"
Total
Length
Item No.
Description
00259560
00259562
00259563
CHSL Hollow CHNL TE-Y KM 2.8/28

CHSL CHNL TE-Y KM 3.6/28
CHSL Flanged CHNL TE-Y KM 3.6/28
Blade
Width
11"
11"
11"
1"
1-1/2"
1-1/2"
For gouging channels in concrete
For cutting channels in hollow block
Clay Spade
Item No.
Description
96204592
TE-Y CLAY SPADE
Total
Length
Blade
Width
17"
4-1/2"
Flexible Chisel
Item No.
Description
00252462
Flex TE-Y BSPM 800
Total
Length
25-1/2"
5-7/8"
For removing linoleum, vinyl tile, coatings
and concrete form cleaning
Mortar Chisel
Total
Length
Item No.
Description
00001929
CHSL MTR TE-Y FGM 6.5/28
Carbide Bushing Tool

Item No.
00062893
Blade
Width
11"
Total
Length
10"
Description
Bushing Tool TE-Y SKHM
Blade
Width
1-5/16"
Blade
Width
1-1/2"x 1-1/2"

Ground Rod Adapters

Item No.
Description
For Use With
00220700
00220701
00220702
TE-Y-RD 1/2"
TE-Y-RD 5/8"
TE-Y-RD 3/4"
TE 52, 54, 55, 72, 74, 75, 76, 92, 505, 705
TE 74, 75, 76, 92, 705
TE 74, 75, 76, 92, 705
www.us.hilti.com
2.46
Hilti TE 805 Breaker

Light And Powerful, The TE 805 Will Positively Impact Your Productivity
TE-S
Advantages
Compact design for operator
comfort
Longer intervals between
service resulting in lower
service costs
Powerful 1350 watt motor
enhances performance
Continuous on/off switch
eliminates need for constant
finger pressure
Support
Built to use Hiltis highperformance chisels
Quick and easy chisel changes

Power input
1350 W
Voltage
Frequency
5060 Hz

2000 blows/min

12.5 ft-lb
Weight
21.3 lb
Dimensions (LxWxH)
23.6" x 4.3" x 7.1"
Chiseling performance in
4000psi concrete with SM36
pointed chisel
Item No.
00255171
Description
TE 805 115 V
00255165
R e p a i r
TE 805 220 V
P r o g r a m

Item No.
Description
00203086
00009354
Hilti Tool Grease

Cleaning Cloth
www.us.hilti.com
2.49
2.47
Hilti TE 905 AVR Breaker

Active Vibration Reduction System Maximizes Operator Comfort
AVR
Active Vibration Reduction
TE-S
Advantages
Reduction in vibration by 2/3
with the revolutionary AVR
system (integrated vibration
damping)
Compact design for operator
comfort
Longer intervals between
service resulting in lower
service costs
Powerful 1600 watt motor for
maximum performance
Continuous on/off switch
eliminates need for constant
finger pressure
Support
Built to use Hiltis highperformance chisels
Quick and easy chisel changes

Power input
1600 W
Voltage
Frequency
5060 Hz

2200 blows/min

12.5 ft-lb
Weight
24.9 lb
Dimensions (LxWxH)
26.8" x 4.3"x 7.1"
Chiseling performance in
4000psi concrete with SM36
pointed chisel
Item No.
00376562
Description
TE 905 AVR 115 V

00376557
TE 905 220 V
R e p a i r
P r o g r a m
(TE 905 only)

Item No.
Description
00203086
00009354
Hilti Tool Grease

Cleaning Cloth
www.us.hilti.com
SP-Chisels see page:
NEW!
2.49
2.48
TE-S & TE-SP Chisels
TE-SP Self-Sharpening Chisels

22
22mm
NEW!
Innovative chisels that set new standards in performance,

lasting sharpness, working comfort and service life.
Advantages
Features and Benefits
Revolutionary new TE-SP Chisels look sharp and stay

sharp. The new self-sharpening chisels are:
More Productive: Innovative polygon geometry means
up to 30% higher productivity than conventional
chisels.
Fewer interruptions: Less sticking in the concrete or
masonry
Cost saving: No resharpening, reforging or
rehardening necessary.
More comfortable to work with, better handling, more
precise
More productive: Constant high performance over the entire chisel life, better breaking effect.
Cost saving: No resharpening, reforging or rehardening necessary.
Fewer interruptions: Less sticking in concrete or masonry.
Increased operator comfort, better handling, more precise.
Pointed chisel
Total
Length
Blade
Width
Item No.
Description
00376492
00376493
00376494
Flat chisel
00376495
00376496
00376497
Wide-flat chisel
00376498
00376499
00376500
00376501
00376502
00376503
TE-SP Chisel sets
TE-SP-SM 36
TE-SP-SM 50
TE-SP-SM 70
NEW
NEW
NEW
TE-SP-FM 36
TE-SP-FM 50
TE-SP-FM 70
NEW
NEW
NEW
360
500
700
max. 32
max. 32
max. 32
TE-SP-SPM 5/36
TE-SP-SPM 5/50
TE-SP-SPM 8/36
TE-SP-SPM 8/50
TE-SP-SPM 12/36
TE-SP-SPM 12/50
NEW
NEW
NEW
NEW
NEW
NEW
360
500
360
500
360
500
max. 50
max. 50
max. 80
max. 80
max. 120
max. 120
NEW
NEW
4 X TE-SP-SM 36
4 X TE-SP-SM 50
Item No.
Description
00377429
00377430
00000000
00000000
TE-SP-SM 36 chisel set

TE-SP-SM 50 chisel set
chisel set
chisel set
360
500
700
Description
00256234
00001829
00088594
Tamping Tool
TE-S-SS Shank
TP-SKHM 40 Head
TP-SKHM 60 Head
set includes
Bushing Tool
Item No.
Shown
Item No.
Description
00256234
00001908
Ballast Chisel
TE-S-SS Shank
TP-STP 150/150 Head
Item No.
Description
00309317
TE-S TI 60
Total
Length
Blade
Width
11-3/4"
----- 1-1/2" x 1-1/2"
--2" x 2"
Total
Length
Blade
Width
11-3/4"
---
--6" x 6"
Total
Length
Blade
Width
23-1/2"
--Blade
Width

For compacting base
For tamping material under railroad ties
Clay Spade
Item No.
Description
Total
Length
00312204
TE-S-SPI-50
19"
3-7/8"
Item No.
Description
Total
Length
Blade
Width
00256233
TE-S-BSPM 800
25-1/2"
6"
Flexible Chisel
For removing linoleum, vinyl tile, coatings and

concrete form cleaning
Ground Rod Adapters
www.us.hilti.com
2.49
Item No.
Description
For Use With
00312056
00312057
00312058
TE-S-RD 5/8" TE 805, TE 905

TE-S-RD 3/4" TE 805, TE 905
TE-S-RD 7/8" TE 805, TE 905
Rotary Hammer Drill Accessories

Extension Cords
NEW!
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0
12.1-16.0
16.1-20.0
20.1-25.0
The sharp point

The polygon design give the
chisel lasting sharpness.
The long length

Flat and pointed chisels feature a
longer working length for extra
life.
Choosing
Tool
Ampere
Rating
Extension Cord Length Extension Cord

25' 50' 75' 100' 150' 200' Wire Size
Wire Size
TE-SP
Self-Sharpening
Chisels
18
18
18
18
16
14
12
12
18
18
18
16
14
12
12
10
18
18
16
14
12
10
10
10
18
16
14
14
10
10
8
8
16
16
12
12
10
8
6
6
16
14
12
10
8
6
6
6
All-Weather Extension Cord

Super Premium:
3 conductor, UL listed, SJEOW
(AWG)
To determine the proper

size and length of extension cord, first refer to the
ampere rating shown on
the tool nameplate. Apply
this value to the chart
showing the recommended
American Wire Gauges
(AWG) for use with electric
tools (at left). Always use
UL Listed extension cords.
When in doubt, use the
next heavier gauge (the
smaller the gauge, the
heavier the cord).
Meets OSHA requirements for outdoor and indoor use. Stays

flexible down to -67F. Withstands heat up to 194F. An
excellent cord that shrugs off oil, grease, acids, solvents, and
offers resistance to abrasion and ozone.
The new shank

A new, innovative shank design
guarantees higher chiseling
performance and better handling.
Item No.
Description
00255079
Extension Cord 10/3 x 50
00255080
00090359
00090360
00090353
00090358
Heavy Duty
Outdoor Heavy Duty Extension Cords
Heavy Duty:
3 conductor, UL listed, SJTW
Vinyl, Orange. Meets OSHA requirements for outdoor and indoor
use. Stays flexible down to -23F. Withstands heat up to 158F.
Item No.
Description
00066500
00066507
00066495
00066499
Three-Way
Outdoor/Indoor Heavy Duty
Three-Way:
3 grounded outlets, 3 conductor, UL listed.
The red ring

The mark of top-class Hilti
quality.
SJTW Vinyl, Orange. Meets OSHA requirements for outdoor

and indoor use.
Item No.
Description
00066509
00066510
00066512
12/3 x 2 x 3 Three-way
Ground Fault Interrupter (GFI)

The effective dust cap
Dust cap to help prevent dust
entering the machine.
The strong connection end

Solid, hexagonal, pre-greased
connection end.
15 A, 120 V, 60 Hz, 15 A rated current

UL listed, meets OSHA, NEC requirements
Ground Fault Trip: 5 mAMP
Trip time: 25 milliseconds
Power Cord: 12/3
Item No.
Description
00086840
GFI x Three-way (15 A)
15/20 Amp Heavy Duty Adapter

Item No.
Description
00255089
15/20 Amp Heavy Duty Adapter
Detail
www.us.hilti.com
2.50
NEW
DG 150 Diamond Grinding System

Drilling Systems
Diamond Drilling Overview
DD EC-1
DD 100 Dry or Dry Vac
DD 100 Wet
DD 100 MEC Rig
Accessories
Diamond Corebits
Page 3.3
Page 3.9+
Page 3.13
Page 3.14
Page 3.15
Page 3.17
Page 3.5
Coring Systems
Diamond Coring Overview
DD 130 Wet or Dry
DD 160E
DD 250E
Accessories
Diamond Corebits
NEW !
Page 3.3+
Page 3.18
Page 3.20
Page 3.23
Page 3.26
Page 3.5
Diamond Corebits
System Overview
Product Begins
Page 3.5
Page 3.27
Diamond Blades
System Overview
Product Begins
Page 3.6+
Page 3.37
Grinding Systems
NEW !
NEW !
Grinding Overview
DG 150 Diamond Grinder
HG 450 Angle Grinder
HG 500-D Angle Grinder
DC 500-S Angle Grinder
DC 700-S Angle Grinder
Page 3.4
Page 3.47
Page 3.49
Page 3.49
Page 3.50
Page 3.50
Abrasive Blades
System Overview
Product Begins
Wire Brushes
Page 3.8
Page 3.51
Page 3.58
Diamond Coring, Cutting & Sawing

Connection
System
System
DD EC-1
tool
Application / BaseApplication
Material
WET
DD-C
Drilling Systems
DD-BI
DD 100
Dry or
Dry Vac
DD 100
Wet
DRY
tool
WET
Class
DD 100
MEC Rig
WET
tool
DD-BI
DD 130
Wet or
Dry
WET
NEW!
3/8" to 1-5/16"
DD-C Super Premium Wet
Diamond Core Bits
Application :
Small/medium diameter
through holes
Dustless dry coring
Base Material :
Brick, Block, Masonry
Lightweight Concrete
Unreinforced Concrete
:
Application
Anchorholes
Small/medium
diameter
through holes
Base Material :
Reinforced Concrete
Natural Stone
1" to 6"
3.13
DD-BI-HDM Dry Diamond
Core Bits
Accessories:
3.17
---------1" to 6"
DD-BT-PM-D Dry Diamond
Core Bits
Application :
Anchor holes
Small diameter through holes
High volume coring
Base Material :
Concrete
Reinforced Concrete
Masonry
Stone
Application :
With a wide range of
applications on a variety of
materials
Base Material :
Reinforced Concrete
Masonry
Stone
Asphalt
Application :
Large anchor holes
Concrete core sampling
Medium diameter through
holes
Base Material :
Concrete
Reinforced Concrete
Stone
Asphalt
Masonry
Accessories:
Accessories:
3.11
000
15/32" to 1-5/8"
DD-BI-HWC Wet Diamond
Core Bits
---------1" to 5"
DD-BI- Wet Diamond Core
Bits
---------1" to 5"
DD-BI-Coastal Wet
Diamond Core Bits
000
3.14
15/32" to 4-1/2"
DD-BI Diamond Core Bit Wet Coring
---------1" to 3-1/2"
DD-BI-Coastal Wet
Diamond Core Bits
3.15
Accessories:
Accessories:
000
3.17
Accessories:
3.17
000
Accessories:
000
1" to 6"
DD-BI Dry Diamond Core
Bits
---------15/32" to 6"
DD-BI Wet Diamond Core
Bits
WET
DD-BU
3.10
000
Application
:
Anchorholes
Small diameter
through holes
Base Material :
Reinforced Concrete
Natural Stone
tool
DD 160E
Page
Page
3.18
Accessories:
3.19
000
3.20
Accessories:
1" to 9"
DD-BU Diamond Core Bit - 000
Accessories:
Wet Coring
3.21
---------1/2" to 9"
DD-BS (PMRS, SM) Bits
with accessory 1-1/4 7
chuck
---------2" to 6"
DD-BU-Coastal Wet
Diamond Core Bits
Class
Coring Systems Class
DRY
Drilling Range
3.3

Connection
System
Application / Base Material
tool
DD 250E
WET
Coring Systems
DD-BU
DG 150
Diamond Grinder
NEW!
Angle Grinding Systems
HG 450
Angle Grinder
HG 500-D
Angle
Grinder
DC 500 S
Angle
Grinder
DC 700-S
Angle
Grinder
Application :
Large diameter through holes
Concrete core sampling
Deep coring
Stitch coring
Base Material :
Concrete
Reinforced Concrete
Stone
Asphalt
Masonry
toolApplication / Base Material
System
NEW!
Drilling Range
Page
1" to 12"
3.23
DD-BU Diamond Core Bit Wet Coring
Accessories:
3.24
14", 16" with adapter
---------1/2" to 12"
DD-BS (PMRS, SM) Bits
with accessory 1-1/4" 7
chuck
14", 16" with adapter
---------2" to 12"
DD-BU-Coastal Wet
Diamond Core Bits
Blades & wheels : diameter
Page
C2 Hard Aggregate
C1 Concrete
D1 Fine Finish
A1 Abrasive Base Material
B1 Spike Coatings
3.47
Application :
Smoothing and shaping
Metal grinding
Rust removal/paint preparation
tool Finishing/surface preparation of metal
Base Material :
Masonry
Mortar
Concrete
Carbon Steel
Stainless Steel
Type 27 Abrasive Blades

Diamond Cup Wheels
Diamond Blades
Wire Brushes/Cups
4-1/2" x 1/8" to 1/4"

4"
4"
3"+ 4"
3.49
Application :
Grinding of steel metal and concrete
Finishing/surface preparation of metal
Base Material :
Masonry
Mortar
Concrete
Carbon Steel
Stainless Steel Non-ferrous Metal

Diamond Blades
Diamond Cup Wheels
Tuck pointing Wheels
Joint Blade
Wire Brushes/cups
Resin Fiber Flap Discs
5" x 1/8" to 1/4"

5"
5"
4" + 5"
4"
3", 4"
5"
3.49
Application :
tool Grinding of steel metal and concrete
Finishing/surface preparation of
metal
Base Material :
Masonry
Mortar
Concrete
Carbon Steel
Stainless Steel Non-ferrous Metal

Diamond Blades
Diamond Cup Wheels
Tuck pointing Wheels
Joint Blade
Wire Brushes/cups
5" x 1/8" to 1/4"

5"
5"
4" + 5"
4"
3", 4"
5"
3.50
Application :
Smoothing, shaping
Weld grinding
Finishing/surface preparation of
metal
Base Material :
Masonry
Concrete
Carbon Steel Stainless Steel

Zirconium Blades
Diamond Cup Wheels
Wire Brushes
Wire Cup Wheels
7" x 1/8" to 1/4"

7" x 1/8" to 1/4"
7"
4"
3", 4", 5"
7"
3.50
Application :
Surface preparation of concrete and
masonry
Removal of coatings from concrete
and masonry
Base Material :
Concrete
Masonry
Natural Stone
Accessories:
3.48
3.4
Wet Coring
Dry Coring
Diamond Core Bits
3.5
Specification
Application
Connection End
Diameters
Page
HDM
Tornado
Dry Coring
Brick and Block
Average Concrete w/Mesh
Dust Removal System Requires Shop Vac
BI
1" to 6"
3.28
PMD
Dry Coring
Brick and Block
Where Dust is Not a Concern
BT (5/8" 11)
1" to 6"
3.28
HWC
Wet Coring
Hand Held Only
Very Fast Coring
Use on Granite, Marble, Tile and Hard Concrete
BI
15/32" to 5"
3.29
T2
Granite, Marble, Tile

Best Speed in Reinforced Concrete
DD-C
3/8" to 1-5/16"
3.12
T4
Reinforced Concrete
Best Life in Concrete
DD-C
1/2" to 1-5/16"
3.12
P2
Wet Coring
Heavily Reinforced Concrete
Low Abrasive Base Material
BI
BT (5/8" 11)
BU
BS (1-1/4" 7)
1" to 5"
1" to 1-1/2"
1" to 16"
1-3/4" to 16"
3.29
3.31
3.30
3.31
P4
Wet Coring
Reinforced Concrete
Abrasive Base Material
BI
BT (5/8" 11)
BU
BS (1-1/4" 7)
15/32" to 5"
1/2" to 1-5/8"
1" to 16"
1-3/4" to 16"
3.29
3.31
3.30
3.31
Coastal
Wet Coring
Heavily Reinforced Concrete
Very Fast Coring
BI
BU
BS
1" to 3-1/2"
2" to 6"
2" to 12"
3.34
SM
Wet Coring
Average Concrete
Light Reinforcement
Best Value for Smaller Jobs
BT (5/8" 11)
BS (1-1/4" 7)
1/2" to 1 5/8"
1-3/4" to 16"
3.32
PMRS
Wet Coring
Pre-Stressed Cable
Wire Mesh
Pre-Cast Concrete
BS (1-1/4" 7)
1-3/4" to 8"
3.33

Heavy Duty
Product Description
Base Material
Equipment
Sizes
Walk Behind Diamond Blades

DS-CC TransPro Super Premium
DS-AG TransPro Super Premium
DS-WB ContractorPro Premium
DS-LWB PowerPro Low Horse Power
Walk Behind Saws

Wet Cutting
12" to 36" diameter

0.110" to 0.375"
thickness
Masonry Diamond Blades
Brick / Fire Brick

Structural Block
Lightweight Block
Glazed Tiles
Refractories
Masonry Saws
Wet + Dry
14" to 20" diameter

0.110" to 0.125"
thickness
3.42+
High Speed Diamond Blades

Super Premium DS-HS
Premium DS-HS
Heavy Duty DS-HD
Brick
Granite
Masonry
Concrete
Asphalt
Block
Hand Held Saws

Cut off equipment
20mm + 1"
Arbors
Dry Cutting
12" to 16" diameter

0.110" to 0.125"
thickness
3.43+
Super Premium Dry Diamond Blades

Continuous Rim and Segmented
Concrete
Masonry
Block
Refractories
Granite
Angle Grinders
Circular Saws
4" to 9" diameter

0.080" to 0.096"
thickness
3.45
Premium Dry Diamond Blades

Continuous Rim and Segmented
Concrete
Masonry
Block
Refractories
Granite
Angle Grinders
Circular Saws
4" to 9" diameter

0.080" to 0.096"
thickness
3.45
DS-WM SuperMason Wet

DS-DM SuperMason Dry
DS-WDM ProMason Wet/Dry
Green Concrete
Asphalt
Cured concrete
Asphalt over concrete
Page
3.40+
Other sizes and

thicknesses
available
3.6

Product Description
3.7
Base Material
Equipment
Sizes
Page
Dry Diamond Blades

Tuck Pointing (Mortar joints)
Mortar joints
Hard mortar joints
Angle Grinders
Circular Saws
4" to 7" diameter

0.250" thickness
3.46
Joint Blade - V Shaped
Concrete/Masonry
Cracks
Joints
Angle Grinder
4" x 0.400"
3.46
Diamond Cup Wheels

DG-CW
Angle Grinders
4", 5", 7" x 5/8"11

Single row
Double row
Turbo
3.46
DG-CW
Concrete
Natural Stone
Masonry
DG 150
6"
3.47
Concrete
Masonry
Stone
Pavement Blocks
Roof Tiles

Product Description
Base Material/Application
Equipment
Abrasive Blades Type 27

Grinding
Grinding of:
Angle Grinders
4" to 9" diameter

1/8" and 1/4" thickness
Abrasive Zirconium
Blades Type 27
Grinding
Grinding of:
Angle Grinders
4 1/2" to 9" diameter

1/8" and 1/4" thickness
3.53

Super Premium
Zirconium
Surface Preparation:
Angle Grinders
4 1/2" to 7" diameter

36-120 grit
3.54
Carbon Steel
Stainless Steel
Non-Ferrous Metal
Cast Iron
Pipeline, Welds
Concrete, Masonry
Various Ferrous and

Non-Ferrous Metals
stainless steel
Grinding, Shaping, Smoothing,

Surface preparation of Metals
Rail Blades
Type 1
Cutting:
Wire Cup and Flat Brushes
Abrasive Thin Cut-Off

Wheels
Type 1
High Speed Abrasive Blades

Drywall Track Blades
Type 1
Walk-behind Saw
Abrasive Blades
Type 1
Page
3.52
3.55
Gas or Hydraulic
saw fixed to rail
14" and 16" diameter

1/8" thickness
Surface Preparation:
Angle Grinders
3" to 6" diameter

4" to 12" diameter
3.58
Cutting of:
Angle Grinders
4 1/2", 5", 6" diameter

0.040" thickness
3.54
Hand held gas,electric

and pneumatic saws
12" to 14" diameter

1/8" to 5/32" thickness
3.57
Track saws
12",14",16" diameter
Circular saws
7" and 8" diameter

3.56
Walk behind saws
14" diameter
3.56
Cutting of all types of rail from main

line to light rail
Rust removal
Weld Cleaning
Paint preparation
Surface finishing
Joint Cleaning
Angle iron,
Misc. Thin Metals
Tubing
PVC, Conduit
Cutting of:
Various Metals, Stainless, Masonry,
Asphalt, Rail track, Ductile Pipe
Metal Studs, Pipe, Misc. Metals,
Structural Steel
Circular Saws
Abrasive Blades
Type 1
Sizes
Cutting of:
Steel
Concrete, Stone
Masonry
Non-ferrous metal
Cast iron
Cutting of:
Cured concrete
Green concrete
Asphalt
3.8
Drilling Systems
TopSpin the future of diamond drilling produces

matched tolerance Hilti anchor holes
innovation at work!
The unique TopSpin principle is based on a slightly eccentric

movement of the core bit. Pressure is transferred selectively
to part of the diamond segment ring, thus causing the
diamonds to cut into the material more deeply and more
effectively. Especially when coring through rebar, Hilti
TopSpin technology in conjunction with the high speed of
8,000 rpm sets new standards in diamond drilling
performance efficiency.
www.us.hilti.com
3.9
Drilling Systems
Hilti DD EC-1 Diamond Drilling System

At 8,000 rpm, TopSpin technology marks the beginning
of a new era in diamond drilling
Main Applications
Drills anchor holes or through
holes of 3/8" to 1-5/16"
(8 to 35 mm) diameter quickly
and accurately
Unique TopSpin technology for
maximum efficiency
Drills through reinforcing bars up
to 100% faster
Less tiring to use thanks to low
weight of 12.5 lb (5.7 kg)
Reduces contact pressure by up
to 40% for higher productivity
Simple, one-person operation
Technical Data
Tool weight
12.5 lb
Power
1450 W
One speed
8000 rpm
Belt Driven
TopSpin kinematics
Distance to corner
1-7/8"
Maximum water pressure

88 psi
Supply cord
Integrated GFCI 10 mA
Removable, 16 ft
Diamond coring with unprecedented mobility and flexibility.
Water regulation
Auto/Manual
Smooth and quiet
Bubble levels
The low-vibration, low-noise Hilti DD EC-1 drills

smoothly and quietly in materials sensitive to
cracking, making it ideal for renovation work and
drilling jobs in inhabited buildings such as offices or
hospitals.
1 vertical, 1 horizontal
Water flow indicator wheel

Integrated centering device and
water collector
DD-C
Item No.
Description
00377420
DD EC-1 Deluxe System with DD-CR1Stand

Includes DD EC-1 drill, DD-CR1 Stand, DD-REC1 water
recycling unit, and additional DD-REC 1 replacement filter
00340573
DD EC-1 Deluxe System

Includes DD EC-1 drill, DD-REC1 water recycling unit,
and additional DD-REC 1 replacement filter
00336737
DD EC-1 Diamond Drill (120 V)

Supplied with: water collector, 16 foot supply cord with
built-in GFCI, depth gauge, Hilti spray, cleaning cloth,
impact-resistant plastic case and operating instructions
00336746
R e p a i r
DD-REC1 Water Recycling Unit
P r o g r a m
Supplied with: removable trolley, 16 foot hose set, cleaning

pad, operating instructions and spare filter
00376281
DD-CR1 Stand
00377255
DD-REC1 Replacement Filter
Case Study #5041013* Project Manager
ADDED
VALUE
$84,450 project labor savings using Hilti DD

EC-1 hand held core rig to drill reinforced
concrete in confined space instead of using a
hammer drill.
www.us.hilti.com
Diamond bits see page:
3.12
3.10
Drilling Systems
Hilti DD REC-1: Water Power!
Technical Data
Tool weight
55 lb (empty) / 84 lb with water
Power
300 W
Dimensions (WxDxH)
19-5/8" x 13-3/8" x 18"
Operating Temperature
23F to 122F
Usable water volume

2.5 gal
Filter life
7001,000 holes
(3/4" diameter x 5" deep)
Cleaning, refill interval

50 holes
(3/4" diameter x 5" deep)
Clean drilling in sensitive environments.
Sensors
Water pressure 88 psi,
water flow, temperature
Economical and environmentally

friendly
Supply lines (in nylon jacket)
The unique water recycling unit, a world first,

uses up to two-thirds less water than conventional
systems. Also equipped with a container to
facilitate environmentally correct disposal of the
drilling slurry.
Water supply hose, slurry removal

hose, 16' electrical supply cord
R e p a i r
Mobile
P r o g r a m
Take it anywhere: The Hilti DD-REC1 ensures

maximum mobility and flexibility on the jobsite thanks
to almost total independence from external water
supplies. It comes complete with a practical trolley for
easy transport.
Automatic
Electronic water management: The pump and
extraction function are activated / deactivated
automatically by the drilling machine control switch.
The operator simply regulates the water flow rate, as
necessary.
Item No.
Description
00336746
DD-REC1 Water Recycling Unit

Supplied with: removable trolley, 16 foot hose set, cleaning
pad, operating instructions and spare filter
00377255
DD-REC1 Replacement Filter
www.us.hilti.com
3.11
Drilling Systems
DD-C Super Premium Wet Diamond Core Bits

T2
T4
Granite, Marble, Tile
Reinforced concrete,
Best life
Faster
More Life
DD-C
guide sleeve
Hilti DD-C Core Bits
T2
For reinforced concrete with medium to low reinforcement, granite, marble,
natural stone, tile, pavers, firebrick and other non-abrasive base materials.
Fast coring bits with tall segments provide long life

Special core bits for optimum transmission of the revolutionary
TopSpin action
Drilling depth up to 12" (longer length available)
T4
For reinforced concrete, concrete block, clay brick, green
concrete, asphalt and other abrasive base materials.
Special DD-C core bits for the DD EC-1 and TopSpin kinematics. Each core bit comes with one matching water collector guide sleeve.
Select bit diameter
and length from
center chart below.
Follow left for T2,
right for T4
T2 single
T2 5-pack
Description
Item No.
Item No.
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
DD-C T2
00336886
00336889
00336890
00336893
00336898
00336900
00336902
00336906
00336904
00336908
00336909
00336911
00336913
00336914
00336915
00336916
00336917
00336918
00336919
00339531
00339534
00339536
00339538
00339541
00339543
00339545
00339547
00339549
00339551
00339552
00339553
00339555
00339556
00339557
00339558
00339559
00339560
00339561
T2
Diameter
3/8"
12 mm
1/2"
9/16"
5/8"
11/16"
3/4"
20 mm
13/16"
27/32"
7/8"
24 mm
1"
28 mm
1-1/8"
30 mm
32 mm
1-1/4"
1-5/16"
T4
Length
6"
150 mm
6"
6"
12"
12"
12"
300 mm
12"
12"
12"
300 mm
12"
300 mm
12"
300 mm
300 mm
12"
12"
T4 single
T4 5-pack
Description
Item No.
Item No.
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
DD-C T4
NA
NA
00336854
00336857
00336862
00336864
00336866
00336870
00336868
00336872
00336873
00336875
00336877
00336878
00336879
00336880
00336881
00336882
00336883
NA
NA
00339563
00339565
00339568
00339570
00339572
00339574
00339576
00339578
00339579
00339580
00339582
00339583
00339584
00339585
00339586
00339587
00339588
24" length EC-I Core Bits available in some sizes.
Tested for anchor applications

Matched tolerance DD-C Core Bits
For optimum load-bearing behavior of the Hilti HVU, HSE,
HSL, HKB, HLC, HCA and HDI anchors
www.us.hilti.com
3.12
Drilling Systems
Hilti DD 100 Dry Diamond Core System

Hand held dry coring in brick and block with or without dust collection
Main Applications
Dustless and hand held coring in
brick and block with dust removal
1" to 6" diameter
(Note: Dust removal system
requires the use of a shop vacuum
suitable for concrete dust collection.)
Technical Data
No load speed: Bit dia.range
1st:
2nd:
3rd:
1200 rpm 2-5/8" to 6"

2400 rpm1-5/8" to 2-1/2"
3900 rpm15/32" to 1-1/2"
Bit Range:
Dry: 1" to 6"
Power Input:
1725 W
Voltage:
115 V
Current Input:
15 A
Weight:
12.6 lb
Accessories
Dimensions (LxWxH):
5/8"11 straight shank adapter for use

with key type 1/2" chucks
17" x 4-1/2" x 6"
DD-C
DD-BI
R e p a i r
P r o g r a m
Item No.
Description
00213925
DD 100 Deluxe
Includes DD 100, plastic kit box, 5/8" DD100 PMD adapter
00332494
DD 100 Deluxe Vacuum

Includes DD 100 Deluxe and dust extraction head and
5/8" DD100 PMD adapter
www.us.hilti.com
3.29
3.35
3.13
Drilling Systems
Hilti DD 100 Wet Diamond Core Drill System

Hand Held Wet Coring In Reinforced Concrete: Simple And Fast.
Main Applications
Hand held wet coring in concrete
15/32" to 1 5/8" diameter
Wet coring with core stand in
concrete 15/32"to 5" diameter
Technical Data
No load speeds: Bit dia. range
1st spd: 1200 rpm 2-5/8" to 6"
2nd spd: 2400 rpm 1-5/8" to 2-1/2"
3rd spd: 3900 rpm 15/32" to 1-1/2"
Bit Range:
Dry: 1" to 6"
Wet: 15/32" to 5"
Power Input:
1725 W
Voltage:
115 V
Current Input:
15 A
Weight:
Accessories
Core Stand DD 80/100 RAL
Anchor/Vacuum Base 8-5/8" x
17" (item No. 00277350)
Anchor Core Stand 4" x 6" Base
(item No. 00213815)
Water Collector Up To:

Hand Held: 1-5/8" diameter
Core Stand: 3-1/2" diameter
Vacuum Pump
5/8" 11 water swivel

(for threaded bits to 1-5/8"
diameter)
Water supply tank
12.6 lb
Dimensions(LxWxH):
17" x 4-1/2" x 6"
DD-C
DD-BI
R e p a i r
P r o g r a m
Item No.
Description
00332495
100 Deluxe Wet

Includes DD 100, plastic kit box, BI water swivel
www.us.hilti.com
ADDED
VALUE
$17,784 project labor savings using Hilti DD

100 hand held core rig to remove connection
cable in tilt wall project versus using a breaker
tool to chisel out cable.
3.29
3.35
3.14
Drilling Systems
Hilti DD 100-MEC Rig

Portable, Lightweight Core Rig
Main Applications
Wet coring in reinforced concrete
for 15/32" to 4-3/4" holes
Precise coring of anchoring holes
15/32" to 1-5/8" diameter
Technical Data
Bit diameter
ranges
No loadspeeds
Features
Compact and lightweight

Low noise level
True running for precise holes
Narrow base for steps, stairs and
other confined areas
Very fast coring for holes up to
4-3/4" diameter
1st speed: 1200 rpm 2-5/8" to 6"

2nd speed: 2400 rpm 1-5/8" to 2-1/2"
3rd speed: 3900 rpm 15/32" to 1-1/2"
Bit Range
Wet: 15/32" to 4-3/4"
Power Input
1725 W
Voltage
115 V
Current Input
15 A (motor only)
Weight
12.6 lb
Dimensions (LxWxH)
17" x 4-1/2" x 6"
Accessories
DD 100-MEC
Water collector and holder for water containment and removal

Vacuum pump for fast rig hold down
Water tank for portable water supply
Optional chuck for threaded 5/8"11 core bits
DD 100-RAL
DD 100
DD-C
DD-BI
R e p a i r
P r o g r a m
Vacuum Pump
DD-WC-S
DD-HS-RA
Item No.
Description
00332420
DD 100-MEC RIG
Includes DD 100-MEC and core rig stand
www.us.hilti.com
3.29
Case Study #1838* Construction Supervisor
ADDED
VALUE
$20,000 project labor savings using Hilti core

rig to drill anchor holes in concrete reinforced
with heavy rebar instead of using a hammer drill.
3.35
3.15
Drilling Systems
DD 100 RAL Core Stand

For use with any DD 100 tool
Applications
Precise positioning and alignment of anchor holes and through holes
High volume small diameter holes with optimized speed and life
Up to 4-3/4" diameter holes wet

Low weight of 24 lb (without DD 100 motor)
Narrow base for steps and other tight areas (8-5/8" x 17")
Column and baseplate with lifting handles for easy
carrying and positioning.
Useable with core bits with up to 17" effective core depth
Water collector and holder for water containment in
any coring direction
Integrated vacuum release valve in baseplate handle for
quick repositioning of core rig
Integrated vacuum gauge in base for easy monitoring of vacuum level
Used With Other System Components
DD 100 or DD 100 MEC Motor

Water collector and holder
Vacuum pump
Application-matched wet diamond core bit program
Item No.
Description
00277350
DD 100 RAL Core Stand
www.us.hilti.com
3.16
Drilling Systems
DD 100 Accessories
Water Collection System
DD 100 RAL Stand and DD 100 MEC RIG
For use with all core bits 15/32" to 4-3/4" diameter
Item No.
Description
00332496
DD-WC-S Complete
00232204
00232224
Includes water collector, holder, 8' drain hose, vacuum adapter
Water Seals
Item No.
Description
For diameter (in.)
00207303
00207304
00207305
00207306
00207307
00207308
00207309
00207310
00207311
00207312
00207313
Water Seal 3/8 S

Water Seal 15/32-1/2 S
Water Seal 9/16-5/8 S
Water Seal 11/16-3/4-27/32 S
Water Seal 7/8-1 S
Water Seal 1 1/8 S
Water Seal 1/1/4-1 3/8-1 1/2 S
Water Seal 1 5/8-1 3/4 S
Water Seal 2-2 1/4
Water Seal 2 1/2-2 3/4 S
Water Seal 3-3 1/2 S
3/8" 15/32" to 1/2"

9/16" to 5/8"
11/16" to 3/4" to 27/32"
7/8" to 1"
1-1/8"
1-1/4" to 1-3/8" to 1-1/2"
1-5/8" to 1-3/4"
2" to 2-1/4"
2-1/2" to 2-3/4"
3" to 3-1/2"
00047298

For DD 100 Hand Held
Description
00332497
DD-WD-H Complete
00046938
00310559
For use with all core bits 15/32" to 1-5/8" diameter

Item No.
For use with water collector shown above
Water Seals
00213637
00046857
00046938
For use with hand held collector shown above

Item No.
Description
For diameter (in.)
00050231
00050232
00050233
00050234
00050235
00050236
00050237
00050238
Water Seal 3/8"-1/2"

Water Seal 9/16"- 5/8"
Water Seal 11/16" - 3/4"
Water Seal 27/32" - 7/8"
Water Seal 1"
Water Seal 1 1/8"
Water Seal 1 1/4"
Water Seal 1 3/8" - 1 5/8"
3/8" to 1/2"
9/16" to 5/8"
11/16" to 3/4"
27/32" to 7/8"
1"
1-1/8"
1-1/4"
1-3/8" to 1-5/8"
Wet Coring Accessories
Item No.
Description
00213633
DD 100 BI Water Swivel
For use with all wet core bits with BI connector
00213747
DD 100 5/8" Water Swivel

For use with all wet core bits with 5/8" 11 connector
Dry Coring Accessories

Item No.
00256883
Description
5/8"11 DD 100 PMD Adapter

For use with all dry core bits with 5/8"11 connector.
00213634
DD 100 1/2" Keyed Chuck With Shank

For use with all dry bits with hex or straight shank.
00332498
DD 100 Dust Extraction Head Complete
For use with all dry core bits with BI connector.

Includes extraction head, and vacuum adapter
00213632
www.us.hilti.com
3.17
00213148
Vacuum pump, water supply and electrical accessories: Page 3.26

Coring Systems
Introducing the Hilti DD 130 Diamond Coring System

Wet or Dry. Hand-held or Stand-mounted
NEW!
Applications
With a wide range of applications
on a variety of materials
For coring holes up to 6" in
masonry and reinforced concrete
Technical Data
Voltage
120 V
Nominal power
1800 W
Nominal current
15 A
Frequency
50/60 Hz
Weight
DD 130 tool: 16.9 lb (7.7 kg)
DD 130 rig: with motor 28.6 lb (13 kg)
Speed (no load)
1st gear: 780 rpm
2nd gear: 1400 rpm
3rd gear: 2600 rpm
Feature and Benefits
Chuck type
Versatility.
Simplicity.
Cores quickly and neatly into reinforced concrete,

natural stone, masonry and asphalt
Hand-hold or mount on a drill stand
Designed for both wet and dry coring without
modification
Drill stand base plate designed for vacuum
attachment and anchor fastening
Mobile and efficient; can be set up and operated

easily by one individual
Water flow conveniently controlled on the
side handle
Simple, click-action attachment to drill stand
The BI+ quick release chuck connects the DD 130
with DD-B+ Series performance core bits. Its a
keyless system that lets you change bits in seconds.
No additional tools are required.
Drill stand adjusts to core at angles up to 45
Quick-release BI+
Min. access to walls

1- 1/2" from the center of the hole
Min. access to corners

2-1/4" from the center of the hole
Max. stroke (rig)

17"
DD-C
DD-BI
Item No.
Description
00373696
DD130 rig kit
Including safety glasses, Hilti spray, operating instructions,

motor and stand
00370461
DD130 drill stand without motor
00092053
VP-1 vacuum pump
00373337
Vacuum seal set (replacement)
www.us.hilti.com
3.28+
3.35
3.18
Coring Systems
DD 130 Accessories
Water Collector Systems
Item No.
Description
00376728
DD130 WCS-H water collector system (hand-held)

Including: water collector holder, water collector ring, 3 m hose,
centering rings, universal splash protector and 2 vacuum attachments
Item No.
Description
00370460
DD130 WCS-R water collector system (rig)
Water collector holder (hand-held)
Including: water collector holder, water collector ring, seal adaptor, 3 m hose,
2 universal splash protectors and 2 vacuum attachments
Water Seals
Item No.
Water collector ring (hand-held)
Water collector ring (rig)
Description
Rig mounted use with 00370460

00050231
Water seal 15/32" 1/2"
00050232
00050233
00050234
00050235
Water seal 1"
00050236
Water seal 1-1/8"
00050237
Water seal 1-1/4"
00050238
Water seal 1-3/8" 1-1/2"
00046103
Water seal 1-3/4" 2-1/4"
00046104
Water seal 2-1/2" 2-3/4"
00046105
Water seal 3" 3-1/4"
00046106
Water seal 3-1/2" 4"
00046107
Water seal 4-1/4" 4-1/2"
00046108
Water seal 4-3/4" 5"
Hand-held use with 00376728
00207304
Water seal 1-5/32" 1/2" S
00207305
Water seal 9/16" 5/8" S
00207306
Water seal 1-1/16" 2-7/32" S
00207307
Water seal 7/8" 1" S
00207308
Water seal 1-1/8" S
00207309
Water seal 1-1/4" 1-1/2" S
00207310
Water seal 1-5/8" 1-3/4" S
00207311
Water seal 2" 2-1/4" S
00207312
Water seal 2-1/2" 2-3/4" S
00207313
Water seal 3" 3-1/2" S
Water collector holder (rig)
Seal adaptor (rig)
Sealing disc
Additional Accessories
Item No.
Description
00220929
00009829
Core bit extension BI+

Portable water tank10' hose
BI+ core bit extension
www.us.hilti.com
3.19
Coring Systems
DD 160E Diamond Core Rig System

Main Applications
Precise holes in the 1"to 9"
diameter range in
steel-reinforced concrete, natural
stone, masonry and asphalt
Through hole penetrations for
cable and pipes, etc
Ventilation holes
Test-cores
Deep-hole coring and angular
coring
Technical Data
Voltage
115 V
Nominal Power
2000 W
Nominal Current
18 A
Speeds
No Load
Bit Diameter
Ranges
1st speed: 500 rpm
Integrated Motor
Features
Service indicator light to
mimimize motor damage
3-speed gearing for optimized
core speed
Mechanical slip clutch for motor
protection
DD-C-BU quick-release chuck: no
tools required
Built-in ground fault interrupter to
help prevent electrical shock
Electronic overload protection to
reduce motor damage
System Features
Benefits
High performance 3-speed motor

Carriage: 8 guide rollers to help
smooth feed operation
maintenance free
Rigid, extendable column
Anchor- and/or vacuum-type
baseplates
Special baseplate for attachment
to pipes 12" or larger in diameter
Stainless steel rack (teeth)
Swivel and tilt/swivel baseplate
cones available
Water collection system
Custom solutions for most

applications
Easy to transport and store
System easy to adapt and
expand
Fast bit/core removal no tools
required
Clean, vibration-free coring
4" to 9"
(102-229 mm)
2nd speed: 1000 rpm 2" to 4"
(52-102 mm)
3rd speed: 2000 rpm 1" to 2"
(25-52 mm)
Max. bit capacity

1" to 9" diameter
Column height
39"
Column dimensions
3" x 3"
Weight
80 lb with motor
Vacuum/anchor base
dimensions (LxW): 18-3/4"x 11-3/4"
DD-BU
Item No.
Description
00256005
DD 160E Combination Vacuum/Anchor Base Rig

Consists of 115 V DD160 motor, DD-C-BU chuck,
DD-CA-S carriage, DD-R-100-S column, DD-CP-S eccentric
pin, DD-BCQ-S base cone, DD-BAV-4 anc/vac base plate,
DD-FH 1/2 hand wheel, DD BW wheels (2). .
00332510
DD 160E Combination Vacuum/Anchor Deluxe Rig

Includes all components listed above for the DD 160E
Combination Vacuum/Anchor Base Rig plus:
DD-SM-SML jack screw, DD-CO-S connecting cone,
DD-EP-S eccentric pin, DD-BCS-S tilt/ swivel cone,
DD-WC-SM water collector, DD-HSM-S water collector
holder, DD-WH 3/4" drain Hose, Vacuum Adapter
R e p a i r
P r o g r a m
www.us.hilti.com
3.30
Rig shown with optional accessories
3.21, 3.26
3.20
Coring Systems
DD 160E Accessories
For core bits 1" to 6-1/2" (25 to 162 mm) diameter
Item No.
Description
00332499
DD-WC-SM Water Collector Complete
00232221
00235825
00047298
00046938
DD-SW-M Water Seals

Item No.
Description
For Use With Bit Size
00207314
00207315
00207316
00207317
00207318
00207319
00207320
00207321
00207322
00207323
00207324
00207325
Water Seal DD-SW-1

Water Seal DD-SW-1 1/8"-1 3/16"
Water Seal DD-SW-1 1/4"
Water Seal DD-SW-2"-2 1/4"
Water Seal DD-SW-4"
Water Seal DD-SW-5 1/2"-6"
1"
1-1/8" to 1-3/16"
1-1/4"
1-5/8"
2" to 2-1/4"
2-1/2" to 2-3/4"
3"to 3-1/2"
4"
4-1/4" to 4-1/2"
5" to 5-1/4"
5-1/2"to 6"
6-1/4" to 6-1/2"
Columns
00232198
Stackable columns for deep coring and ceiling bracing
Item No.
Description
00332501
DD-R 100-S Extension Kit (39" length)
Includes DD-R 100-S column, connecting cone, and eccentric pin x 2
00232195
00232197
Jack Screw Spindle

For bracing rig to ceiling; makes great handle for moving and lifting rig
Item No.
Description
00332500
Jack Screw Kit
00009854
00232198
00232197
Includes Jack Screw DD-SL-SML, connection cone, eccentric pin x 2
Chucks
Item No.
Description
00232235
DD-CB-S 1 1/4 Universal chuck

For use with 1-1/4" 7 threaded core bits (DD-BS, PM, PMRS, SM)
DD-BV-P Special Vacuum Baseplate

Item No.
Description
00232220
DD-BV-P baseplate
13" bit capacity with spacer. Fits concrete pipe or columns 12" diameter or larger
www.us.hilti.com
3.21
Coring Systems
Create Your Own Customized Diamond Coring System

Benefits Of A Modular Core Rig System
Very flexible with broad
application range
Simple, one-person handling
with compact and lightweight
components
Highly economic system for
most common applications
Fast and easy set up and

breakdown, user friendly and
easy to transport
Basic core rig can be upgraded
to complete system
00009854
00232231
00232198
Chuck (BU) 00232234
00232197
00232192
00232195
00009843
00232197
00232198
00235812
00235812
End Stop
End Stop
00235812
00232194
00232197
00232196
End Stop
00232195
00232192
00232197
00232197
00232197
00232195
00232224
00232197
00232199
00232200
00232199
00232202
00232220
00232203
00232204
special order
00232202
special order
www.us.hilti.com
3.22
Coring Systems
DD 250E Diamond Core Rig System

Main Applications
Precision holes in the 15/32" to
16" diameter range in steelreinforced concrete, natural
stone, masonry and asphalt.
Penetrations for cables and
pipes, etc.
Ventilation holes
Test cores
Deep hole coring and angular
coring
Stitch coring for large openings
High volume coring with custom
rig combinations
Technical Data DD 250E Motor

Voltage
115 VAC 50/60 Hz
Amperage
20 A
Power Input
2300 W
Weight
40 lb (motor only)
110 lb (with motor)
Speeds
No Load
Bit Diameter
Ranges
1st speed: 275 rpm
8" to 16"
(202 to 400 mm)
2nd speed: 450 rpm 4" to 8"
(102 to 202 mm)
3rd speed: 950 rpm 2" to 4"
(56 to 102 mm)
4th speed: 1800 rpm 1" to 2"
(25 to 56 mm)
Max. bit capacity

12" dia (16" with optional spacer)
Column Height
39"
Column dimensions
3-1/2" x 3-1/2"
Vacuum base dimensions (LxW)

22-1/8" x 13-3/4"
System Features
Integrated Motor Features and Benefits
High performance, 4-speed motor

Carriage: 8 guide rollers to help smooth feed
operation
Rigid, extendable guide rails
Anchor and/or vacuum-type baseplates
Special baseplate for attachment to pipes 12" or
larger in diameter
Stainless steel rack (teeth)
Swivel and tilt/swivel baseplate cones available
Water collection system
4 motor speeds allow a wide range of optimized

coring diameters
Benefits
Earth-ground conductor (grounded) carries stray

current to ground
Custom solutions for most high volume, medium to

large diameter applications
DD-BU
Easy one-person handling, including set up and

breakdown
One motor to handle most applications
Electrical protection with built-in ground fault
interrupter and UL listed construction
DD-CU-BU quick release chuck no tools required

Electronic control unit maintains constant motor
speed (rpm) while providing current overload
protection. Maximizes bit life and performance.
Additional protections against motor damage.
Power cord with integrated GFI to help protect
operator from electric shock
Electronic restarting interlock helps prevent
unintended motor startup after power interruption
Electronic starting current regulator: delays motor

startup to avoid current input surge and extra load on
breakers
Hole-starting mode switch reduces rpm by 1/3 for
easier hole starting
Slip clutch helps provide mechanical protection
against overloading
Service indicator light alerts operator that motor
needs to be serviced approximately 10 hours prior to
brushes wearing out.
R e p a i r
P r o g r a m
www.us.hilti.com
3.30
Item No.
Description
00332511
DD 250E Combination Vacuum/Anchor Base Rig
Includes 115 V DD 250E motor, DD-C-BU Chuck,

DD-CAS carriage, DD R100S column, DD-CP-S eccentric pin,
DD-BCQ-S base cone, DD-BAV-10 baseplate, DD-FH 1/2
hand wheel, DD-BW wheels (2).
00332512
DD 250E Combination Vacuum/Anchor Deluxe Rig
Includes all components listed above for the DD 250E plus:

DD-SL-SML Jack Screw, DD-CO-ML connecting cone,
DD-EP-ML eccentric pin, DD-BCS-ML Tilt/Swivel cone,
DD-WC-ML water collector, DD-HML-M water collector
holder, DD-WH 3/4" drain hose, vacuum adapter
3.24, 3.26
Rig shown with optional accessories
3.23
Coring Systems
DD 250E Accessories
For Core Bits 1" to 6-1/2" Diameter (Small Ring Components)
Item No.
Description
00232221
Water Collector
00235851
Water Collector Holder
00047298
8' Drain Hose
00046938
Vacuum Adapter
For Core Bits 4" to 10" Diameter (Large Ring Kit)
Item No.
Description
00332502
DD-WC-ML Water Collector Complete
00232221
00235851
00047298
00046938
DD-SW-M Water Seals

For use with water collector to 6-1/2" diameter
Item No.
Description
00207314
Water Seal DD-SW-1
00207315
00207316
00207317
00207318
00207319
00207320
00207321
Water Seal DD-SW-4"
00207322
00207323
00207324
Water Seal DD-SW-5 1/2"-6"
00207325
For use with water collector 00332502 (above) to 10" diameter
00207333
Water Seal DD-SW-L 4"
00207334
Water Seal DD-SW-L 4 1/4" - 4 1/2"
00207335
Water Seal DD-SW-L 5" - 5 1/4"
00207336
Water Seal DD-SW-L 5 1/2" - 6"
00207337
Water Seal DD-SW-L 6 1/4" - 6 1/2"
00207338
Water Seal DD-SW-L 6 3/4"
00207339
00207340
00207341
00207342
For Use With Bit Size
1"
1-1/8" to 1-3/16"
1-1/4"
1-5/8"
2" to 2-1/4"
2-1/2" to 2-3/4"
3" to 3-1/2"
4"
4-1/4" to 4-1/2"
5"to 5-1/4"
5-1/2" to 6"
6-1/4" to 6-1/2"
4"
4-1/4" to 4-1/2"
5" to 5-1/4"
5-1/2" to 6"
6-1/4" to 6-1/2"
6-3/4"
7"
8"
9"
10"
Chucks
Item No.
Description
00232235
DD-CB-S 1 1/4 Universal chuck

For use with 1 1/4" - 7" threaded core bits (DD-BS, PM, PMRS, SM)
DD-BV-P Special Vacuum Baseplate

Fits DD 160E and DD 250E Core Rigs
Item No.
Description
00232220
DD-BV-P baseplate
13" bit capacity with spacer

Fits concrete pipe or columns 12" diameter or larger
Columns
00232241
Stackable columns for deep coring + ceiling bracing
Item No.
Description
00332503
DD-R 100-M Extension Kit (39" length)
Includes DD-R 100-M column, connecting cone, and eccentric pin x 2
00232244
00232211
Jack Screw Spindle

For bracing rig to ceiling; makes great handle for moving and lifting rig
Item No.
Description
00332504
Jack Screw Kit
Includes Jack Screw DD-SL-SML, connection cone, eccentric pin x 2

00009854
00232241
00232244
Spacer
For use with DD250 to expand core bit capacity to 16"
Item No.
Description
00252799
DD-EA-M spacer
www.us.hilti.com
3.24
Coring Systems
Create Your Own Customized Diamond Coring System

Benefits Of A Modular Core Rig System
Very flexible system with broad
application range
Simple one person handling
with compact and lightweight
components
Highly economic system for

most common and many
specialized applications
Fast and easy set-up and
breakdown, user friendly and
easy to transport
For specific application questions and assistance in customizing your Hilti

DD 250E core rig, contact Hilti Technical Support at 1-800-879-6666.
00221090
00252799
00232207
00232208
00009854
00232241
00009843
00235928
00232209
00232244
End Stop
00232241
00232212
00232241
00232244
00009854
00232211
00232213
59" Expandable
Column
(not shown)
00232209
00207131
00232211
00232244
00232244
00232222
00232219
00232215
00232243
00232218
(4" to 10")
Special
order
00232216
00232220
00232219
00092053
www.us.hilti.com
3.25
Coring Systems
Diamond Coring Accessories

Vacuum Pump
00092053
Vacuum Pump VP-1

(For use with any Hilti or most competitive Diamond Core Rigs)
Portable Water Tank

For use with any hand held or rig type diamond core rig.
2-1/2 gal useable water capacity
Use anywhere water is not readily available
Tank fitted with pressure gauge, stabilizing base, hose and all connectors
Item No.
Description
00009829
Water Supply Tank

Includes 10' hose and quick connectors
Water Flow Indicator

In-line indicator for visually verifying water flow and flow adjustments.
For use with all Hilti diamond core rigs.
Item No.
Description
00009301
Water Flow Indicator
Item No.
Description
00375973
15/20 AMP Twist Lock Adapter

Adapts 15/20 AMP Twist Lock to Standard 3 Prong Grounded Plug
Item No.
Description
Length
00375960
00375963
00375959
00375962
Extension Cord 12/3 x 50'

Extension Cord 12/3 x 100'
Premium Extension Cord 10/3 x 50'
Premium Extension Cord 10/3 x 100'
50'
100'
50'
100'
Sharpening Stones
Description
00314303
00051343
Small
Large
Choosing Extension Cord

Wire Size (AWG)
An undersized cord will cause a drop in voltage, resulting in loss of power
and overheating of the tool. Use an extension cord heavy enough to carry the
current your tool requires. A heavier gauge extension cord is required as the
distance from the electrical supply outlet increases.
To determine the proper size and length of extension cord, first refer to the
ampere rating shown on the tool nameplate. Apply this value to the chart at
right showing the recommended American Wire Gauges (AWG) for use with
electric tools. Always use UL Listed extension cords. When in doubt, use the
next heavier gauge (the smaller the gauge, the heavier).
Hilti extension cords are UL Listed and meet OSHA requirements for indoor
and outdoor use.
Length
1" x 1" x 11"

12" x 12" x 2"
Tool
Ampere
Rating
25'
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0
12.1-16.0
16.1-20.0
20.1-25.0
18
18
18
18
16
14
12
12
Wire Size
Item No.

50'
75' 100' 150' 200'
18
18
18
16
14
12
12
10
18
18
16
14
12
10
10
10
18
16
14
14
10
10
-
16
16
12
12
10
-
16
14
12
10
-
www.us.hilti.com
3.26
Diamond Core Bits
Hilti Diamond Core Bits

HWC
P2
P4
Faster
More Life
T2
Coastal
SM
HDM
PMRS
PMD
T4
Connection Ends
Hilti BI
Hilti BU
Hilti Threaded
Fits Hilti
Fits Hilti
BS (1-1/4"7)
DD 100
DD 100 MEC
DD 80 Core Rigs
DCM1
DD 160E
DD 250E
DCM1.5
Fits older models Hilti and competive

Core Rigs
BT (5/8"11)
DD 250E
DCM II
Retipping
Retippable DD-B Modular Diamond Core Bits*
Why throw away perfectly good diamond core bit barrels and connection ends?
Retip your DD-B diamond core bits using the Hilti unique Change Module System!
Retippable
Easy retipping of worn core bits

Change modules with brazed service interface. Worn core bits can be reconditioned
quickly and easily: Remove the old change module, clean the interface, braze on
the new module finished!
Barrel, base and connection end can be reused.
Core bit effective coring depth does not change barrel is simply
cleaned and rewelded
* All Hilti HWC / P2 / P4 and P130 bits 1-3/8" to 7" are retippable.
Call 1-800-879-8000 Today For Retipping Service Details!
www.us.hilti.com
3.27
Diamond Core Bits

Faster
HDM
PMD
Glazed Brick
and Concrete
Brick and Block
More Life
BI
DD-BI Super Premium Dry Diamond Core Bits

Used with DD 100 with dust extraction head and vacuum cleaner
Works L
ike a
TORNA
DO
HDM
For dry coring of brick and block, medium to soft aggregate concrete with
wire mesh.
Item No.
Description
Dry Diamond Core Bit DD-BI 1"/12"

Dry Diamond Core Bit DD-BI 1-1/4"/12"
Dry Diamond Core Bit DD-BI 1-3/4/12"
Diameter (in.)
Length (Useable)
1"
1-1/4"
1-1/2"
1-3/4
2"
2-1/2"
3"
3-1/2"
4"
5"
6"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
Connector
Item No.
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
96333650
96333651
96333652
96333653
96333654
96333655
96333656
96333657
96333658
96333659
96333660
Stock Status
2D
2D
2D
2D
2D
2D
2D
2D
2D
2D
2D
Note: HDM core bits require the use of a dust extraction head and shop vacuum suitable for concrete dust collection.
DD-BT Premium Dry Diamond Core Bits

Used without dust collection system.
Approved operator dust protection required.
BT
PM-D
For dry coring of abrasive brick and block only.
Description
Diameter (in.)
Dry Diamond Core Bit DD-BT 1-00 PM-D

1"
1-1/4"
1-1/2"
1-3/4"
2"
2-1/2"
3"
3-1/2"
4"
5"
6"
Length (Useable)
10"
10"
10"
10"
10"
10"
10"
10"
10"
10"
10"
Connector
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
Item No.
00260781
00260782
00260783
00260784
00260785
00260786
00260787
00260788
00260789
00260790
96254353
www.us.hilti.com
3.28
Diamond Core Bits
DD-BI Super Premium Wet Diamond Core Bits

P2
P4
Granite, marble, tile

best speed
best life
Faster
More Life
DD-BI
HWC
Retippable
Hilti BI Quick Connection
Select sizes
No Tools Required
HWC
P2
P4
Hand held wet coring in hard aggregate and

heavy rebar
For hand held coring with DD 100
For wet coring in reinforced concrete with very

hard aggregate. Also good for granite,
marble, tile, glazed brick and other hard base
materials with low abrasiveness.
Use with all sizes and grades of rebar.
For wet coring in reinforced concrete with

medium to hard aggregate. Also good for clay
brick, concrete block and limestone.
HWC
Description
Diameter/Length
Nominal Diameter
Diamond Core Bit DD-BI

12 mm/13"
1/2"/13"
9/16"/13"
5/8"/13"
11/16"/13"
3/4"/13"
20 mm/13"
27/32"/13"
7/8"/13"
24 mm/13"
1"/13"
28 mm/13"
1-1/8"/13"
30 mm/13"
32 mm/13"
1-1/4"/13"
1-3/8"/17"
1-1/2"/17"
1-5/8"/17"
1-34"/17"
2"/17"
2-1/4"/17"
2-1/2"/17"
2-3/4"/17"
3"/17"
3-1/4"/17"
3-1/2"/17"
4"/17"
4-1/4"/17"
5"/17"
15/32" (12 mm)

1/2"
9/16"
5/8"(16 mm)
11/16"(18 mm)
3/4"
20 mm
27/32"
7/8"(22 mm)
24 mm
1"
28 mm
1-1/8"
30 mm
32 mm
1-1/4"
1-3/8"(35 mm)
1-1/2"(40 mm)
1-5/8"(42 mm)
1-3/4"(47 mm)
2"(52 mm)
2-1/4"(57 mm)
2-1/2"(66 mm)
2-3/4"(72 mm)
3"(77 mm)
3-1/4"(82 mm)
3-1/2"(92 mm)
4"(102 mm)
4-1/4"(112 mm)
5"(132 mm)
Working Length
Bit Connector
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"HWC/17"P
12-5/8"HWC/17"P
12-5/8"HWC/17"P
17"
12-5/8"HWC/17"P
17"
17"
17"
17"
17"
17"
17"
17"
17"
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
Item No.
370567*
370569*
370570*
370571*
370572*
370574*
370575*
370576*
370578*
370579*
370580*
370582*
370583*
370585
370586
370587
-
P2
Item No.
370245
370247
370250
370253
370255
370931
370932
370934
370935
370936
370937
370939
370940
370941
370943
P4
Item No..
370295*
370296*
370298*
370299*
370300*
370301*
370302*
370303*
370304*
370305*
370307*
370308*
370309*
370310*
370311*
370312*
370313*
370315
370316
370317
370998
370999
371001
371002
371003
371004
371006
371008
371009
371011
*This item non-retippable

Matched tolerance DD-B Core Bits
www.us.hilti.com
3.29
Diamond Core Bits
DD-BU Super Premium Wet Diamond Core Bits

P2
P4
Granite, marble, tile

best speed
best life
Faster
More Life
DD-BU
Retippable
Hilti BU Quick Connection
Select sizes
No Tools Required
P2
P4


P2
Description
Diameter /Length
Nominal Diameter
Diamond Core Bit DD-BU

1"/17"
28 mm/17"
1-1/8"/17"
30 mm/17"
32 mm/17"
1-1/4"/17"
1-3/8"/17"
1-1/2"/17"
1-5/8"/17"
1-34"/17"
2"/17"
2-1/4"/17"
2-1/2"/17"
2-3/4"/17"
3"/17"
3-1/4"/17"
3-1/2"/17"
4"/17"
4-1/4"/17"
5"/17"
6"/17"
6-1/4"/17"
7"/17"
8"/17"
9"/14"
10"/14"
12"/14"
14"/14"
16"/14"
1"
28 mm
1 1/8"
30 mm
32 mm
1-1/4"
1-3/8"(35 mm)
1-1/2"(40 mm)
1-5/8"(42 mm)
1-3/4"(47 mm)
2"(52 mm)
2-1/4"(57 mm)
2-1/2"(66 mm)
2-3/4"(72 mm)
3"(77 mm)
3-1/4"(82 mm)
3-1/2"(92 mm)
4"(102 mm)
4-1/4"(112 mm)
5"(132 mm)
6"(152 mm)
6-1/4"(162 mm)
7"(182 mm)
8"(205 mm)
9"
10"
12"
14"
16"
Working Length
Bit Connector
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
14"
14"
14"
14"
14"
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
BU
P4
Item No.
Item No.
370259*
370263*
370269*
370272
370273
370274
370951
370952
370954
370955
370956
370958
370960
370961
370962
370964
370965
370967
370969
332505
332506
332507
332508
332509
370321*
370323*
370325*
370327*
370329*
370331*
370332*
370334
370335
370336
371105
371106
371108
371110
371111
371113
371114
371115
371117
371118
370119
371120
371122

www.us.hilti.com
3.30
Coring Systems
DD-BS/BT Super Premium Wet Diamond Core Bits

DD-BS
Faster
P2
P4
Granite, marble,
tile best speed
best life
More Life
DD-BT
BS (1-1/4"7) Connection End
Retippable
Select sizes
Internally Threaded
BT (5/8"11) Connection End

Internally threaded
P2
P4


P2
Description
Diameter /Length
Nominal Diameter
Diamond Core Bit DD-BT

Diamond Core Bit DD-BS
1/2"/13"
5/8"/13"
11/16"/13"
3/4"/13"
27/32"/13"
7/8"/13"
1"/13"
1-1/8"/13"
1-1/4"/13"
1-3/8"/17"
1-1/2"/17"
1-5/8"/17"
1-34"/17"
2"/17"
2-1/4"/17"
2-1/2"/17"
2-3/4"/17"
3"/17"
3-1/4"/17"
3-1/2"/17"
4"/17"
4-1/4"/17"
5"/17"
6"/17"
6-1/4"/17"
7"/17"
8"/17"
9"/14"
10"/14"
12"/14"
14"/14"
16"/14"
1/2"
5/8"(16 mm)
11/16"(18 mm)
3/4"
27/32"
7/8"(22 mm)
1"
1-1/8"
1-1/4"
1-3/8"(37 mm)
1-1/2"(40 mm)
1-5/8"(42 mm)
1-3/4"(47 mm)
2"(52 mm)
2-1/4"(57 mm)
2-1/2"(66 mm)
2-3/4"(72 mm)
3"(77 mm)
3-1/4"(82 mm)
3-1/2"(92 mm)
4"(102 mm)
4-1/4"(112 mm)
5"(132 mm)
6"(152 mm)
6-1/4"(162 mm)
7"(182 mm)
8"(205 mm)
9"
10"
12"
14"
16"
Working Length
Bit Connector
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
12-5/8"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
14"
14"
14"
14"
14"
BT
BT
BT
BT
BT
BT
BT
BT
BT
BT
BT
BT
BT
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
BS
P4
Item No.
Item No.
370288*
370289*
370290*
370291*
370292
370294
370975
370976
370978
370979
370980
370981
370983
370984
370985
370987
370988
370989
370990
370992
-
370360*
370362*
370363*
370364*
370365*
000000*
370367*
370368*
370369*
370371
370372
370373
371125
371126
371128
371130
371131
371133
371134
371135
371137
371138
371140
371142
96062463*
62464*
62465*
62466*
96061132*

www.us.hilti.com
3.31
Coring Systems
DD-BS/BT Premium Wet Diamond Core Bits

Faster
SM
DD-BS
More Life
Concrete
DD-BT
BS (1-1/4"7) Connection End

Internally Threaded
Retippable
BT (5/8"11) Connection End
Select sizes
Internally threaded
SM
For use with Hilti and other manufacturers core rigs using 1-1/4" 7 or 5/8"11 connection ends.
SM
Bit series formulated to provide exceptional
value to those with light to medium duty
coring applications. SM bit series is designed
for coring in a wide range of concrete
conditions with soft to hard aggregate and light
to medium steel reinforcing.
SM
Description
Diameter
Working Length
Bit Connector
Item No.
Stock Status
Wet Diamond Core Bit SM 0-12 / 14"

1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
1-3/8"
1-1/2"
2"
2-1/4"
2-1/2"
2-3/4"
3"
3-1/4"
3-1/2"
4"
4-1/4"
4-1/2"
5
5-1/4"
5-1/2
6"
7"
8"
9"
10"
12"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
1/2" 20
1/2" 20
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
5/8" 11
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
96046677
96046678
96046679
96046680
00046681
00046682
96046683
00046684
00046696
96046697
00046698
96046685
00046686
96046687
96046688
00046689
96046690
96046691
00046692
96046693
96046694
00046695
96046699
00046700
96046701
00046702
96046703
96046704
10D
10D
10D
*
*
*
10D
*
*
10D
*
10D
*
10D
2D
*
10D
10D
*
10D
10D
*
2D
*
10D
*
2D
2D
* Also available with BU connection ends
Stock Status:
*
Regular Stock Item
2D
2 business days plus shipping from East Coast typical
10D
www.us.hilti.com
3.32
Coring System
Specialty Wet Diamond Core Bits

DD-BS
PMRS
Faster
More Life
Pre-stressed Concrete,
good speed and life
BS (1-1/4" 7) Connection End

Internally Threaded
PMRS
For use with Hilti and other manufacturers core rigs using 1-1/4" 7 connection end.
PMRS
Bits
PMRS
Unique premium bit series especially designed for coring applications
where embedded pre-stressed cable, wire mesh or heavy rebar in small
diameters are anticipated. The special webbing between the segments
prohibits such metal obstacles from lodging between the segments which
often results in segment loss.
Conventional
Bits
Special
Gullets
Wire
Bundle
PMRS
Description
Diameter
Wet Diamond Core Bit PMRS 1-34 / 14"

1-3/4"
2"
2-1/2"
3"
3-1/2"
4"
4-1/2"
5"
5-1/2"
6"
7"
8"
Working Length
Bit Connector
Item No.
Stock Status
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
14"
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
1-1/4" 7
96062846
00062577
00062578
00062579
00062580
00062581
00062582
00062583
00062584
00062585
00062570
00062571
2D
*
*
*
*
*
*
*
10D
*
10D
2D
BS (1 1/4" - 7)
Connection End
Internally Threaded
Hole Genie Assembly
Walker Duct
For use with Hilti and other manufacturers core rigs.
Walker Duct
Combines the efficiency of diamonds in
coring concrete and carbide in metal cutting to
create a fast, economical solution for recessed
inserts (communications, electrical, computer,
etc.) in Walker Duct.
BS Connector 1-1/4" 7 Internally

threaded
Carbide Hole Saw
Open Back
Diamond Bit
Expansion Adapter
Walker Duct
Description
Diameter
In Concrete
Diameter
In Duct
Bit Connector
Item No.
Stock Status
Wet Diamond Core Bit DD-BS- 2 1/2" / 2 1/4" WD
2-1/2"
2-1/4"
1-1/4" 7
96025865
2D
Special Length Diamond Core Bits & Other

Specialty Diamond Core Bit Configurations
www.us.hilti.com
3.33
Diamond core bits can be supplied in custom lengths. Optional connection

ends, custom matrix specifications, threaded barrel bits and other diameters
are available. Contact Hilti Customer Service or your Local Sales
representative at 1-800-879-8000.
Stock Status
*
Regular Stock Item
2D 2 business days
plus shipping from
East Coast typical
10D 10 business days
plus shipping from
East Coast typical
Coring System
Coastal Core Bits

Connection ends to fit all Hilti and Competitive Core Rigs.
Faster
Coastal
DD-BI
More Life
DD-BU
Reinforced concrete, heavy rebar great speed, good life
DD-BS
Coastal
Super premium core bit for very fast coring in very hard aggregate and
heavy rebar applications.
A good balance of speed and life with an extremely tall 11mm segment.
Description
Diameter
Working Length
BI
Wet Diamond Core Bit Coastal 1"/17"

Wet Diamond Core Bit Coastal 1-1/8" / 17"
Wet Diamond Core Bit Coastal 2" / 17"
1"
1-1/8"
1-1/4"
1-1/2"
2"
2-1/4"
2-1/2"
3"
3-1/2"
4"
5"
6"
8"
10"
12"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
17"
96254694
96254695
96254696
96254697
96254689
96254690
96254691
96254692
96254693
Connection End
BU
BS (1 1/4"7)
96254706
96254635
96254708
96254637
96254638
96254639
96254640
96254641
96254642
96254643
96254644
96254710
96254711
96254712
All Coastal core bits have a 2D delivery status
www.us.hilti.com
3.34
Diamond Core Bits
Dry Diamond Core Bit Accessories

Adapters
Item No.
Description
00256883
5/8"- 11 / DD-100 Dry Core Bit Adapter
00258080
PM-D Straight Shank Adapter
5/8"- 11 Thread For Dry Diamond Core Bits, BT Connection To DD-100 Chuck
5/8"- 11 Thread For Dry Diamond Core Bits, Straight Shank For Jacobs Chuck)
Extension
Item No.
Description
00092049
BT (5/8" 11) Core Bit Extension
Length
7"
Minimum Core Bit Diameter
7/8"
For 5/8" 11 core bits > 7/8" diameter
Wet Diamond Core Bit Accessories

DD-BI Connection End
Adapters
Item No.
00373422
Description
1-1/4"7 Adapter BI
Converts 1 1/4" - 7 Spindle to BI Quick Connection
00373419
00373420
1-1/4"7 Adapter BI to BS
5/8"11 Adapter BI to BT
Extension
Item No.
Description
Length
00220929
BI Core Bit Extension
11.8"
2-1/4"
DD-BT Connection End (5/8"- 11) Internal Thread

Reducers
Item No.
Description
00092052
Reducer 1 1/4"7 to 5/8" 11
DD-BU Connection End

Adapters
Item No.
00009869
Description
1-1/4"7 Adapter BU
Converts 1 1/4" 7 Spindle to BU Quick Connection
Extensions
Item No.
Description
Length
00000074
BU Core Bit Extension
11.8"
2-1/2"
Length
DD-BS Connection End

Adapters
Item No.
Description
00004427
BU to BS (1-1/4" 7 Thread)
Converts BU Quick Connection to BS
Extensions
DD-BS Connection End (1 1/4" 7) Internal Thread
Item No.
Description
00092050
BS (1-1/4" 7) Core Bit Extension
00009802
Core Bit Ring Pack
12"
1-5/8"
Qty. 6, Use Between Bit End And Motor For Easier Bit Removal)
For DD-BS (PM, SM) bits 1-1/4" thread only.
www.us.hilti.com
3.35
Diamond Core Bits
Factors Influencing Diamond Bit Performance

Net Result to Performance
Variables
Change
Material
Hardness
Aggregate Size
Material
Abrasiveness
Bit Life
harder
slower
longer
softer
faster
shorter
Softer materials get ripped apart by the diamonds. Those edges are larger and coarser getting
through the material quicker, but shortening bit life.
smaller
faster
shorter
Aggregate is denser than concrete. Small pieces take less time to core through. Bit life is
shorter because the aggregate chips off into sharp edges, the matrix drops the diamonds.
larger
slower
longer
more
faster
shorter
Abrasiveness causes matrix wear. This exposes more diamonds that may fall from the matrix
before they wear out.
less
slower
longer
Lack of abrasiveness retards matrix wear, fewer new diamonds are exposed. The bit lasts
longer but cuts slower.
light
faster
longer
Cutting through steel which is very tough and dense compared to concrete wears a bit very
quickly. Decreasing the amount of steel improves cutting.
heavy
slower
shorter
To cut heavy steel reinforcement you can increase pressure, and/or rpms. Alternately you can
decrease water flow or add sharp silica sand into the hole. All decrease bit life.
harder
softer
slower
faster
longer
shorter
A harder matrix slows the controlled erosion of exposing new diamonds.
less
faster
shorter
Causes the cuttings to remain in the hole, this exposes more diamonds giving a faster coring
speed, but shorter life.
more
lower
slower
faster
longer
shorter
Too much water retards matrix erosion, and may lead to bit glazing.
higher
slower
longer
The matrix becomes glazed with higher than recommended rpms, thus affecting cutting
speed. Less contact time with the concrete decreases cutting.
lower
slower
longer
Low pressure allows the bit to glaze. Bit life goes up, performance goes down.
higher
faster
shorter
High pressure exposes new cutting edges that cut faster but the diamonds may fall-out
before they wear out. Excessive pressure may cause the crown to collapse.
Embedded Steel
Matrix Hardness
Water Volume
(rpm)
Motor Speed
(Pressure)
Bit Feed Rate
Reasons for
Performance Change
Drilling Speed
Harder materials are usually less abrasive. They are cut into small, fine particles that dont
wear the matrix. Since new diamonds arent exposed coring speed goes down, bit life goes up.
Large aggregate takes longer to core through, bits last longer because the cuttings from the
aggregate come off in smaller, finer, pieces causing less matrix wear.
Bit life decreases because of faster matrix erosion. Diamonds fall-out not wear out.
Cuttings/slurry not cleared from hole. The cuttings expose new diamond edges that cut fast
and wear fast. The diamonds are in contact with the concrete longer so they cut faster.
Sharpening Procedure for Diamond Core Bits

Diamond core bits must maintain good diamond exposure in order to work efficiently. Many factors work in unison to provide the controlled erosion cycle of
the bit segment. When this controlled erosion cycle is altered, the bit can become dull or glazed. Glazing becomes noticeable when the
coring feed rate slows dramatically or the bit does not cut. Examine the bit immediately. If the diamonds are flush with the metal, they are underexposed or
glazed.
The following steps will often correct this problem:
1. Reduce water flow until it becomes very muddy. Continue using as little water as possible until penetration increases.
2. If bit does not open up, remove from hole. Pour into kerf a thick (1/4") layer of silica sand, the coarser the better.
3. Resume coring for approximately 3 to 5 minutes with very little water and at a lower RPM if possible.
4. Gradually increase water flow to flush sand from kerf.
5. Repeat as needed.
Alternate sharpening procedure:
Use sharpening stone designed for diamond core bits.
Sharpening Stones
Item No.
Description
00314303
00051343
Small
Large
Length
1" x 1" x 11"

12" x 12" x 2"
www.us.hilti.com
3.36
Diamond Blades
How Diamond Blades Work
Technical Information
Maximum Blade Cutting Depths
Diamond Blades are actually grinding

wheels with diamond particles as the
abrasive agent. Individually
exposed diamond particles are
held in place by a metal
matrix. These diamond
particles, often visible at
the leading edge of a
bond tail (also called
comet tail remove
material by scratching
out particles of hard,
dense substances, or
by knocking out larger
particles of loosely
bonded, abrasive materials.
This process eventually cracks
or fractures the diamond particle,
breaking it down into small pieces. To
control this planned process, the diamond
type, quality, and grit is matched to the saw and the
base material.
Note: Diamond blade cutting

depths listed are approximate.
Actual cutting depth will vary with
the exact blade diameter or saw
type (or brand), or the exact
diameter of the blade flanges.
Cutting depth will also be reduced
if saw components (motor
housing, blade guard, etc.) extend
below the blade flanges.
As the diamond particles break down through

contact with the base material, the metal matrix
holding the diamond particle also begins to wear.
Large particles of soft, abrasive materials wear
down this metal matrix faster than the small
particles removed from hard, dense materials.
Because of this, a diamond blade for cutting a soft,
abrasive material must have a hard metal matrix
composition to resist this erosion long enough for
the exposed diamonds to be properly utilized.
Conversely, a blade for cutting a hard, non-abrasive
base material must have a soft bond to insure that
it will erode and expose new diamonds embedded
in the matrix. These simple
principles are the foundation of controlled bond
erosion.
This controlled bond erosion continues until the
blade segment is consumed. It is important to
understand that the diamond blade and the base
material must work together to allow this process to
occur enabling the blade to work effectively.
Right Angle Grinder
Masonry Saw
Circular Saw
Low HP Saw (5-18 HP)
Std HP Saw (18-35 HP)
High HP Walk Behind (35-65 HP)
Walk Behind Diamond Blades

12"
14"
16"
18"
20"
24"
26"
30"
36"
42"
48"
3-5/8"
4-5/8"
5-5/8"
6-5/8"
7-5/8"
9-5/8"
10-5/8"
11-5/8"
14-5/8"
17-5/8"
20-5/8"
Masonry Saw Diamond Blades

14"
18"
20"
5"
7"
8"
High Speed Blades for Gas Hand

Held Saws
12"
14"
16"
4"
5"
6"
High Speed Gas Saw
*These are symbols only. Make sure appropriate guarding is utilized for your particular application.
Wet or Dry Blades?

Water Cooled
Wet cutting diamond blades must be
used with water to prevent excessive
heat build-up during cutting. Using water
also reduces dust and helps remove
cuttings. A continuous water flow is
critical. Using wet blades without water,
even for a few seconds, causes
excessive heat and blade damage, and
creates a safety hazard. Check the saw
or tool carefully before using a wet
cutting diamond blade. Make sure it is
safe to use the saw or tool with water.
Air Cooled
Dry-cutting blades eliminate the need for
water tanks, water hoses, and wet slurry
cleanup. These blades depend on airflow
around the blade to prevent excessive
heat buildup during cutting. Use dry
diamond blades for intermittent sawing.
After every 10 to 15 seconds of cutting,
take pressure off the blade and allow it
to run back up to full speed for several
seconds. This cooling interval allows air
to flow around the blade. Use dry blades
for shallow cutting only (1-2" deep) or
step cutting. The use of water with dry
blades will not increase life or cutting
speed, but will reduce dust.
www.us.hilti.com
3.37
Diamond Blades
Green or Cured Concrete?

The drying or curing time of concrete greatly affects
how the material will interact with a diamond blade.
Green concrete is freshly poured concrete that has
set up but not yet fully cured. It is softer and more
abrasive than cured concrete. A harder bonded
blade is required to cut green concrete. Typically but
not always a softer bonded blade would be required
to cut the same concrete in a cured state.
temperature, moisture in the aggregate, time of year

and the amount of water in the mix all influence
curing time. Also, concrete now can have additives
which can either shorten or extend curing time.
Consult your mix design
to find the relative curing time for your job. As soon
as wet concrete sets up and does not spall or ravel,
green cutting can begin.
Usually, concrete defined as green is 72 hours from

pour or younger, but this can vary widely. Weather,
Undercut Protection
for Segmented Diamond Blades
Diamond blades used to saw abrasive materials such as green concrete and asphalt are
susceptible to premature wear (called undercutting). Undercutting is caused by abrasive
slurry wearing away the steel blade core, usually just below the diamond segment,
causing lateral movement and premature wear on the segment. Undercut core
protection delays this undercutting and allows maximum performance from
your Hilti blade.
SLURC - Slanted undercut retardant

core
Blade Wearing Too Fast or Not Cutting?

The hardness or softness of a diamond blade is
determined by the hardness or softness of the
metal matrix in which the diamonds are
suspended. The hardness is indicated by the
number or specification (see specification chart for
specific type of blade). A high number indicates a
hard blade, while a lower number indicates a
softer blade.
In general, a harder blade should be used when
cutting softer, more abrasive materials and a
softer blade should be used on harder, denser
materials. The reason for this is the diamonds are
doing the actual cutting, not the metal matrix.
Therefore, soft abrasive material (block, asphalt,
green concrete) will cause the metal matrix to wear
away more rapidly on a soft blade thereby
exposing the diamonds more quickly. By exposing
the diamonds at a faster rate the cutting will go
faster but the blade life will be shorter.
Conversely, a hard-non-abrasive material (hard
brick, glazed tile) will not wear away the matrix as
fast on a hard blade. This will result in longer

blade life, but the cutting will not be as fast since
the diamonds are exposed at a slower rate.
As a general rule, if you find a blade is wearing too
fast, the matrix may be too soft for the material
being cut, try using a harder blade (higher
number). If a blade is cutting too slowly or not
cutting at all, move to a softer blade (lower
number).
Many factors dramatically influence blade
performance. Even after following the blade
selection procedure, blade performance can be
less than anticipated due to the many
unanticipated external influences surrounding the
sawing application. These may include: the
condition of the saw, operator technique,
unexpected aggregate/steel content in the base
material, concrete PSI, etc.
Review each sawing application separately and
monitor the blade carefully during operation to
insure tool cost efficiency. Hilti Sales
Contact Hilti Customer Service at 1-800-879-8000

to help with blade selection or products not shown in this catalog.
www.us.hilti.com
3.38
Diamond Blades
Wet Diamond Blades For Walk Behind Saws

Diamond Blade Specification Selection
TransPro Super Premium Series: This high-performance line of

diamond blades is designed to meet the demanding requirements of
contractors who are highly experienced in production pavement
sawing. These blades are intended for use on high-horsepower
(35 hp to 65 hp) saws and will deliver excellent production rates
coupled with economical cutting costs.
ContractorPro Premium Series: Designed primarily for the

general contractor who needs a diamond blade that will provide
cost-effective life performance and will meet production rate
requirements on medium to large size jobs. These blades will
generally provide the best balance between blade life and cutting
speed when used on mid-range saws, 18 hp to 35 hp, but can
also be used effectively by experienced operators on higher
horsepower equipment.
PowerPro Low Horse Power Series: Value-priced line of

diamond blades that are well-suited for use on low-horsepower
(<18 hp) saws to cut many different types of concrete and asphalt
pavement. Provides free-cutting characteristics and good value to
the contractor. Ideal for small jobs.
www.us.hilti.com
3.39
Diamond Blades
TransPro Super Premium Blades

For Cured Concrete, Asphalt/Green Concrete
Hard Aggregate, Heavy rebar
Very Good Speed
Cured Concrete
Asphalt
Faster
100
High HP Saw (35-65 HP)
More Life
200
300
400
600
750 900
Series Standards
Formulated for wet use only

Standard 1" arbor hole with drive pin hole
Super Premium segment composition
Undercut protection (slurc) on all blades
Laser welded segments
Carbon adjusted steel cores
Cured Concrete Blades (DPCC)

0.315 usable segment height 0.075 backer pad
Applications:
Description
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
DSCC
Size
12"x 0.125"
14"x 0.110"
14"x 0.125"
14"x 0.150"
14"x 0.250"
14"x 0.375"
16"x 0.125"
18"x 0.125"
18"x 0.150"
18"x 0.165"
20"x 0.125"
20"x 0.150"
24"x 0.150"
24"x 0.165"
26"x 0.150"
26"x 0.165"
30"x 0.165"
30"x 0.187"
36"x 0.165"
36"x 0.187"
48"x 0.220"
Hard Aggregate Hard Aggregate

Heavy Rebar
Medium Rebar
General Purpose
Light Rebar
General Purpose
Asphalt Overlay
100
96253789
00253790
00253791
96253792
96253793
96253794
96253795
96253796
96253797
96253798
96253799
96253807
96253808
96253809
96253823
96253831
-
300
96254884
96253885
00253886
96253887
00253888
96253889
96253890
96253891
96253892
96253893
96253894
96253895
96253896
96253897
-
400 stock
96253901 2D
96253902 2D
96253903 10D
96253898 2D
96253904 2D
96253905 2D
96253906 2D
-
stock
10D
*
*
10D
2D
10D
10D
10D
10D
10D
10D
2D
10D
10D
10D
10D
-
200
96253833
96253835
00253839
96253844
96253911
96253899
96253845
96253849
96253852
96253856
96253858
96253859
96253868
96253877
96253878
96253879
96253880
96253881
96253882
96253883
96253900
stock
10D
10D
*
10D
10D
2D
10D
2D
2D
10D
2D
10D
10D
2D
10D
2D
2D
10D
10D
10D
2D
stock
10D
10D
*
10D
2D
10D
2D
10D
10D
10D
10D
10D
10D
10D
-
Specifications
100 CC For cutting cured concrete with
extremely hard aggregates, or for use
in areas where the sand used in the
concrete mix is relatively non-abrasive.
The blade of choice for sawing
pavements with heavy steel
reinforcement.
200 CC Designed to cut a range of
cured concrete mixes that contain
medium to medium-hard aggregates and
are moderately abrasive. Also performs
very well when cutting light to medium
steel reinforced concrete.
300 CC For longer life on a wide range
of cured concrete pavements with
medium to very soft aggregates, and
that are moderately to highly abrasive.
400 CC This formulation is specifically
designed to cut asphalt overlays in
combination with cured concrete
pavements with soft to medium hard
aggregates.
Asphalt/Green Concrete (DPAG)

0.300 usable segment height 0.080 backer pad
Applications:
Description
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
DSAG
Hard Aggregate
Rebar
Size
12"x 0.125"
12"x 0.187"
14"x 0.125"
14"x 0.150"
14"x 0.187"
14"x 0.250"
18"x 0.125"
18"x 0.150"
18"x 0.165"
24"x 0.165"
24"x 0.187"
26"x 0.165"
30"x 0.165"
Soft/Medium
Aggregate
Light Rebar
Asphalt
600
stock
750
stock
900 stock
96253915 10D 96253938 10D 96253947 10D
96253930 10D 96253939 10D
96253933 2D 96253940 2D 96253948 2D
- 96253941 10D
96253934 2D 96253942 10D 96253949 10D
96253935 2D 96253943 2D 96253950 10D
96253936 2D 96253944 2D 96253951 10D
96253937 2D
- 96253952 10D
- 96253945 10D
96253907 2D
- 96253946 2D
96253908 2D 96253910 2D
96253909 2D
-
Specifications
600 AG For green concrete with extremely
hard to medium-hard aggregates. Will
provide an excellent balance between blade
life and cutting speed across a wide range
of concrete mix designs.
750 AG Will provide outstanding overall
performance in green concrete pavements
with soft to medium aggregate hardness
and moderate to highly abrasive sand. Also
may be used to achieve faster cutting speed
in asphalt mixes with hard aggregates.
900 AG Good balance of blade life and
cutting speed in a broad range of asphalt
cutting applications, excellent
performance in highly abrasive asphalt.
www.us.hilti.com
3.40
Diamond Blades
Cured Concrete
Asphalt
Faster
More Life
300
200
600
900
ContractorPro Premium Blades

Std HP Saw (18-35 HP)
200 CC Designed to cut a range of

cured concrete mixes that contain
medium to medium-hard
aggregates, and medium rebar, or
base materials that are moderately
abrasive. Also performs very well
when cutting light to medium steel
reinforced concrete.

Premium segment composition
Undercut protection (slurc) on all 600 &
900 series blades and 200 & 300 series
blades 24" and larger
Applications:
Hard Aggregate Med. Aggregate

Medium Rebar Light Rebar
300 CC For longer life on a wide

range of cured concrete pavements
with medium to very soft
aggregates, and light rebar that are
moderately to highly abrasive.
600 AG For green concrete with

extremely hard to medium-hard
aggregates and rebar. Will provide
an excellent balance between blade
life and cutting speed across a
wide range of concrete mix
designs.
900 AG Good balance of blade life
and cutting speed in a broad range
of asphalt cutting applications,
excellent performance in highly
abrasive asphalt.
Description
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
DS-WB
Size
12" x 0.110"
12" x 0.125"
12" x 0.375
14" x 0.110"
14" x 0.125"
14" x 0.250"
14" x 0.375"
18" x 0.125"
20" x 0.125"
24" x 0.155"
24" x 0.175"
26" x 0.155"
30" x 0.175"
36" x 0.175"
Green Concrete
Asphalt
200
Stock
300 Stock
600
Stock
900 Stock
00337205 *
96337206 2D 00337227 2D 96337228 2D
96337207 2D 00337208 *
00337229 2D 96337230 2D
00337237 2D
00337209 2D 96337210 2D 00337231
* 96337232 2D
00337211 *
00337212 *
00337233
* 00337234 *
96337213 2D 96337235 2D 96337236 2D
96337214 2D
00337215 *
00337216 *
00337238 2D 00337239 *
00337217 *
00337240
* 96337241 2D
96337218 2D 00337219 *
00337242 2D 00337243 2D
96337220 2D 96337221 2D 96041380 2D 96041381 2D
96337222 2D 00337223 2D 00337244
* 00337245 2D
96337224 2D 00337225 2D 00337246
* 96337247 2D
96337226 2D 96337248 2D 96337249 2D
PowerPro Low Horse Power Blades

Low HP Saw (5-18 HP)
Cured Concrete Balanced

formulation to provide
acceptable blade life and
cutting rate performance in
many types of cured concrete.
Not recommended for concrete
mixes that contain extremely
hard aggregates.
Asphalt/Green Concrete Offered
in a single specification that
provides a good performance
value when cutting a variety of
abrasive pavement materials,
especially asphalt. Serves as a
good combination blade, 80%
asphalt and 20% green
concrete, for infrequent users.
Not generally recommended for
extended use in cutting green
concrete.
www.us.hilti.com
3.41

Special D or wide slot design
Applications:
Description
DS-LWB
DS-LWB
DS-LWB
DS-LWB
General Purpose Green Concrete

Cured Concrete Asphalt
Size
12"x 0.125"
14"x 0.110"
14"x 0.125"
18"x 0.125"
Stock Status:
*
2D
10D
Regular Stock Item

Cured Stock Green Stock

00253785 * 00253899 *
00253786 * 00253900 *
00253787 * 00253911 *
00253788 * 96253914 2D
Other diameters, thicknesses
and specifications available.
Contact your local Hilti Sales Representative
or Hilti Customer Service 1-800-879-8000.
Diamond Blades
Granite
Brick and Block
Limestone
Faster
More Life
WM1
DM1
WM2
DM2
WM3
DM3
WM4
DM4
WM5
SuperMason Wet Series

Standard 1" arbor hole
Super Premium Wet Masonry

Recommended for a full range of production wetcutting masonry jobs where both maximum
productivity and a high level of diamond blade
cost-effectiveness are required.
Applications:
Granite
Hard Brick
Fire Brick
Description Size
WM1 Stock
DS-WM
14"x 0.110"x1" 00253953 *
DS-WM
14"x 0.125"x1" 00253957 *
DS-WM
20"x 0.125"x1" 96254167 2D
WM3
WM1 A fast, free-cutting blade for use
on structural brick, brick pavers, firebrick
and other non-abrasive materials.
WM2 A general purpose brick blade
also effective on structural tiles and
hard, dense block
Marble
Structural Tile
Structural Block
Pavers
Clay Brick
Concrete Block
Lightweight Block Sandstone

Limestone
Firebrick
<70% Alumina
WM2 Stock
WM3 Stock WM4 Stock
WM5 Stock
00253954 *
96253955 2D 96253956 2D
00253958 *
00253959 * 96253960 2D
96253961 10D 00253962 * 96253963 2D 96253964 10D
A good combination brick/block

blade. Makes a very good general
purpose blade.
WM4 A long life blade for concrete

block, limestone and other abrasive
materials.
Stock Status
*
Regular Stock Item
2D 2 business days
plus shipping from
East Coast typical
10D 7 business days
plus shipping from
East Coast typical
WM5 A very long life blade for

sandstone, soft firebrick and other highly
abrasive materials.

Contact your local Hilti Sales
Representative or Customer
Service 1-800-879-8000.
SuperMason Dry Series

Formulated for wet and dry cutting
Fast cutting, wide gullet design
SuperMason Dry Masonry:

Recommended for high-production, dry-cutting masonry jobs
where the diamond blade must deliver the lowest possible cost
per cut.
Applications:
Granite
Hard Brick
Fire Brick
Description
DS-DM
DS-DM
DS-DM
DM1
Size
14"x 0.110"x1"
14"x 0.125"x1"
20"x 0.125"x1"
Marble
Structural Tile
Structural Block
Pavers
Clay Brick
Concrete Block
Lightweight
Block
Limestone
DM1
Stock
DM2 Stock
DM3
Stock
DM4
Stock
96253965 2D 00253966 * 00253967
*
00254168 *
00253968 *
00253969 * 00253970
*
00253971 * 00253972
*
00253973 *
Fast cutting of a range of materials that are extremely

hard and dense, and relatively non-abrasive including very hard
structural brick, some refractory brick, and very hard natural
stone materials.
DM2
Fast cutting of a wide variety of brick materials,
including brick pavers and acid brick. An excellent combination
blade for dry cutting of many different types of brick.
DM3
An outstanding multi-application blade for dry cutting of

both brick (60%) and block (40%). This blade will provide its best
performance when used on a blend of brick and block materials,
and when you avoid extremely hard brick and very abrasive block.
DM4
Provides very long blade life, and reasonable cutting

speed, on all types of soft brick, concrete pavers, and block. This
can also be used as a longer-life combination blade for dry
cutting of block (80%) and brick (20%).
Stock Status
*
Regular Stock Item
2D 2 business days
plus shipping from
East Coast typical
10D 7 business days
plus shipping from
East Coast typical
Contact your local Hilti Sales
Representative or Customer
Service 1-800-879-8000.
www.us.hilti.com
3.42
Diamond Blades
Brick and Block
Granite
Limestone
Faster
More Life
WDM3
WDM2
ProMason Wet & Dry Series

Standard 1" arbor hole
ProMason
Recommended for lower volume and intermittent cutting with
wet or dry masonry saws. Blades perform well in a large variety
of common masonry materials.
Applications:
Description
DS-WDM
DS-WDM
Brick WDM2
Clay and medium

hard brick cutting with good
cutting speed and average life.
Clay Brick
Med Hard Brick
Size
14" x 0.110" x 1"
20" x 0.125" x 1"
Concrete Block
WDM2
00338402
WDM3
00338403
Concrete Block WDM3

General purpose concrete block
cutting with good cutting speed
and average life.
Heavy Duty Dry Blades

Series Standards
NEW!
General Purpose (Turbo)
For
cutting of marble, brick, reinforced
concrete and other hard, nonabrasive base materials. A good
choice for fast, clean and
economical cutting.
General Purpose (Segmented)
For cutting of concrete, concrete
block, clay brick, limestone and
other medium hard/abrasive base
materials. A good choice for
balanced cutting speed and life.
Formulated for dry use blades can be used wet to help reduce dust and noise
Standard 20mm arbor with 1" knockout
Formulated for fast cutting in a large variety of base materials
Blade thickness 0.118" for quick and economical cutting
Carbon adjusted and tensioned steel cores
Applications:
Marble
Brick
Reinforced
Concrete
Size
Description
DS-HD
Blade Style
12"x.118"x1"/20 mm
DS-HD
14"x.118"x1"/20 mm
Pkg Qty
Single
5 Pack
Single
5 Pack
Gen Purpose
Turbo
00375265
00375269
00375266*
00375270*
Concrete
Concrete Block
Clay Brick
Limestone
Gen Purpose
Segmented
00375263
00375267
00375264
00375268
* 14" = 0.125" thickness
www.us.hilti.com
3.43
Diamond Blades
Brick and Block General Purpose
Granite
Sandstone
Faster
More Life
General Purpose Turbo
Granite
General Purpose Segmented
Sandstone
Super Premium Dry Blades

Series Standards
Formulated for dry use - blades can be used wet to help reduce dust and noise
Optimized blade design for each specification
Blade thickness 0.125" for reduced flexing
Drive pin hole for use with low horsepower walk
behind saws
Applications:
Granite
Glazed Brick
Tile
Concrete
Description
DS-HS
Size
Blade Style
12"x.125"x1"/20 mm
DS-HS
14"x.125"x1"/20 mm
DS-HS
16"x.125"x1"/20 mm
Granite (Turbo) For cutting of

granite, glazed brick, tile, firebrick
(alumina over 90%) and other very
hard, non-abrasive base materials.
Also the best choice for very fast
and clean cutting.
Pkg Qty
Single
5 Pack
Single
5 Pack
Single
Granite
Turbo
00333673
00336604
00333674
00336605
-

For cutting of marble, brick,
reinforced concrete, firebrick
(alumina over 80%) and other hard,
non-abrasive base materials. A good
choice for fast and clean cutting
with a good balance of life.
Marble
Brick
Reinforced
Limestone
Concrete
Concrete Block
Clay Brick
Gen Purpose
Turbo
00333668
00336600
00333669
00336601
00333670
Gen Purpose
Segmented
00333665
00336598
00333666
00336599
00333667

block, clay brick, limestone, firebrick
(alumina over 70%) and other
medium hard/abrasive base
balanced cutting speed and life. Can
also be used on low horsepower
walk behind saws for cured
concrete.
Sandstone
Green Concrete
Asphalt
Haydite Block
Sandstone
Segmented
00333671
00336602
00333672
00336603
Sandstone (Segmented)
For cutting of sandstone, green
concrete, lightweight concrete,
mortar, asphalt, firebrick (alumina
over 70%) and other soft and
highly abrasive base materials. A
good choice for long life. Can also
be used on low horsepower walk
behind saws for green concrete
and asphalt.
Premium Dry Blades

Series Standards
Formulated for dry use blades can be used wet to help reduce dust and noise
Formulated for fast cutting in a large variety of base materials
Blade thickness 0.110" for fast and good life
Applications:
Marble
Brick
Reinforced
Concrete
Size
Description
DS-HS
Blade Style
12"x.110"x1"/20 mm
DS-HS
14"x.110"x1"/20 mm
Pkg Qty
Single
5 Pack
Single
5 Pack
Gen Purpose
Turbo
00333677
00336608
00333678
00336609
Concrete
Concrete Block
Clay Brick
Limestone
Gen Purpose
Segmented
00333675
00336606
00333676
00336607

For
cutting of marble, brick, reinforced
concrete and other hard, nonabrasive base materials. A good
choice for fast, clean and
economical cutting.
block, clay brick, limestone and
other medium hard/abrasive base
balanced cutting speed and life.
www.us.hilti.com
3.44
Diamond Blades
Faster
More Life
Granite
General Purpose Segmented
Sandstone
Super Premium Dry Cutting Blades
Applications:
Small diameter diamond blades for angle grinders and circular saws
Super Premium formulation in three specifications
for fast cutting speed with excellent life;
best value for the high volume user
Standard 5/8" arbor with 7/8" knockout
7" with diamond arbor knockout - DM
Granite
Clay Brick
Formulated for dry use
Marble
Glazed Brick
Tile
Description
Super Premium DC-D
Super Premium DC-D
Super Premium DC-D
Super Premium DC-D
Size
Pkg
Blade
Qty
4"x 0.080"x 7/8 1
4 1/2"x 0.080"x 7 1
5"x 0.080"x 7/8 1
7"x 0.094"x DM 1
Granite
Turbo
00315456
00315457
00315458
00315459
Concrete Block
Concrete
Stock
*
*
*
*
Gen Purpose
Segmented
00315467
00315468
00315469
00315470
Stock
*
*
*
*
Asphalt
Green Concrete
Lightweight Block
Limestone
Sandstone
Segmented
00315478
00315479
00315480
00315481
Stock
*
*
*
*
DM = Diamond Knockout fits 7/8", 5/8" and diamond arbors

All 7/8" arbor blades supplied with 5/8" bushing
Granite Best suited for granite, marble,

glazed brick, firebrick, tile and other
hard, non-abrasive materials, fast
cutting
General Purpose For use on a wide

variety of base materials such as
concrete, concrete block, limestone and
clay brick
Sandstone Optimum choice for soft

abrasive materials such as sandstone,
lightweight concrete block, haydite block,
asphalt and green concrete
Premium Dry Cutting Blades

Small diameter diamond blades for angle grinders and circular saws
Premium formulation in a general purpose specification for a good balance
of cutting speed and life; best value for the lower volume user
Standard 5/8" arbor with 7/8" knockout
7" and 8" with diamond arbor knockout DM
Packaged
in convenient
Applications:
Description
Premium DC-D
Premium DC-D
Premium DC-D
Premium DC-D
Premium DC-D
Premium DC-D
Premium DC-D
blade
packs
Size
Pkg Qty
4"x 0.080" x 7/8
2
4-1/2"x 0.080" x 7/8
2
5"x 0.080" x 7/8
2
6"x 0.080" x 7/8
2
7"x 0.094" x DM
2
8"x 0.094" x DM
2
9"x 0.094" x 7/8
2
Marble
Clay
Brick
Tile
Firebrick
Concrete Block
Concrete
Limestone
Gen Purpose
Gen Purpose
Turbo
Stock Segmented Stock
00315471
*
00315460
*
00315472
*
00315461
*
00315473
*
00315462
*
00315474
*
00315463
*
00315475
*
00315464
*
00315476
*
00315465
*
00315477
*
00315466
*
DM = Diamond Knockout fits 7/8", 5/8" and diamond arbors

All 7/8" arbor blades supplied with 5/8" bushing
Stock Status:
*Regular Stock Item
www.us.hilti.com
3.45
Other diameters, thicknesses and specifications available.

Contact your local Hilti Sales Representative or Hilti Customer
Service 1-800-879-8000.
General Purpose Segmented, best used on concrete,

concrete block, clay brick, limestone, for economical
cutting on smaller jobs
General Purpose Turbo Style, best choice for marble,
brick, tile, firebrick, for economical cutting on smaller jobs
Diamond Blades
Faster
More Life
Joint Blade
Turbo Cup Wheels
Segmented Cup Wheels
Hard Mortar
General Purpose
Mortar
Premium Dry Tuck Point Blades

Mortar joint removal
Renovation
Standard 7/8" Arbor, 5/8" bushing included
Applications:
Description
Premium DC
Premium DC
Premium DC
Premium DC
Size
Pkg Qty:
4"x 0.250"x 7/8
4 1/2"x 0.250"x 7/8
5"x 0.250"x 7/8
7"x 0.250"x DM
Hard Mortar
Fast Cutting
Concrete
Concrete Block
1X
00333636
00333637
00333638
00333639
General Purpose Mortar

Good Balance of Life and Speed
Sandstone
Green Concrete
Hard Mortar DC-TH

General Purpose DC-T
12X
50X
Stock
1X
12X
50X
Stock
00338229 00338230
*
00333632 00336610 00336612
*
00338231 00338232
*
00333633 00336611 00336613
*
00333634
*
00333635
*
-
All blades supplied with a 5/8" bushing
Premium Dry Joint Blade

For crack and joint repair
Surface preparation
Very aggressive labor saving method for preparing cracks and damaged joints for
sealing or caulking repairs. V design grinds, cleans and shapes cracks for proper
sealant/caulking application. One step operation.
Applications:
Description
Super Premium DC
General Purpose Cleans and Prepares Cracks

One-step Operation
Size
4"x 0.400"x5/8"-11
Joint Blade
00251887s
Stock
*
Diamond Cup Wheels
One specification for all applications

All cup wheels with integrated 5/8"11 connector
No tools required for mounting wheels
Excellent design for use with dust extraction hoods
Single Row
Best used for fast grinding, heavy material removal, roughening of the base material
Double Row
Best used for long wheel life, light surface material removal, smoothing of the base
material
Turbo Style
Best used for long wheel life, light surface material removal, smooth finish of the base
material
Applications:
Description
DG-CW
DG-CW
DG-CW
General Purpose
Diameter
4"
5"
7"
Single Row
00340629
00340632
00340635
Style
Double Row
00340630
00340633
00340636
Turbo
00340631
00340634
00340637
www.us.hilti.com
3.46
Grinding Systems
Introducing the Revolutionary Hilti

DG 150 Diamond Grinding System
NEW!
The Clean Machine

Top grinding performance
Unique cup wheels with innovative
boomerang segments remove
material at a rate almost twice as
fast as a standard cup wheel.
Technical data
(DG150 with DPC20)
Nominal voltage:
120 V
Nominal current:
No clogging
Employing a new self-sharpening
principle, Type B1 cup wheels
remove thin coatings with less
clogging. The new innovative
sharpening technology is perfect for
removal of thin coatings like epoxy
and glue.
15.0 A
Power input:
1800 W
Power output:
1285 W
Mains frequency:
60 Hz
No-load speed, setting no. 1:

4700 rpm
Built to last
The powerful, two-speed, brushless
SR motor has a life expectancy up to
30 times longer than conventional
angle grinders.
No-load speed, setting no. 2:

6600 rpm
Weight (without DPC 20):

9.0 Lbs.
Cup wheel diameter:

6 Inches
Approval/Listing:
CSA
Power Cord 2 Wire:

Double Insulated
Dimensions (Tool):
Also offers a high rate of removal and a smooth finish on concrete,

natural stone and masonry.
Right to the edge

The new dust head design rotates to
allow easy access to those hard-toreach areas.
18 L x 10 W x 9 H
Quick stop:
in two seconds or less after switching
off. Restart interlock, adjustable grip,
dust hood with opening section and
adjustable in height
Item No.
Description
00374258
DG 150 grinder system dlx w/vacuum

Includes grinder, vacuum and vacuum accessories
00374263
DG 150 grinder system w/vacuum

Includes grinder and vacuum
00369388
DG 150 diamond grinder system w/power conditioner

Includes grinder only
Diamond cup wheels for the Hilti DG150 (dry grinding)

Cup wheel: 6 inch diameter
Color
Item No.
Description
C2
00369415
DG-CW 6" C2
C1
00369414
DG-CW 6" C1
For hard aggregate concrete

C2
C1
D1
A1
General purpose concrete
D1
00369417
DG-CW 6" D1
For fine finishing on concrete,
rounding edges
A1
00369413
DG-CW 6" A1
For sandstone, green concrete
www.us.hilti.com
B1 (Spike)
00369418
DG-CW 6" B1 (spike)

For coatings on concrete, sealers
and paint
3.48
B1 (Spike)
3.47
NEW!
The Perfect Compliment to the DG 150
SELF-C
LEA
NIN
G
Hilti VCD 50 Dry Vacuum
FIL
TE
Grinding Systems
Suction
Hilti VCD 50
Conventional
Vacuum
Amount of Dust Removed

Filter Cleaned
The above graph illustrates that even after only a few minutes, the suction capacity of conventional vacuums decreases. Filter
cleaning only briefly improves performance.

Consistently high suction performance over long periods of time
Reduce annoying stops for filter cleaning
Dust control up to 95% dust free
Item No.
Description
00374268
VCD 50 dry vacuum cleaner deluxe kit

Includes vacuum and vacuum accessories
00369405
VCD 50 Dry Vacuum Cleaner

Accessories for the VCD50
Item No.
Description
00370636
Accessory set
For the VCD 50: 2 extension tubes, 1 rotating nozzle with
bend, 1 floor nozzle with brushes, 1 narrow nozzle, 1 hose
(complete), 1 tapered adapter
00370635
Dust bags (5x)

For use with the VCD 50 Dry Vacuum
www.us.hilti.com
3.48
Grinding Systems
HG 450
HG 500-D
NEW!
Technical Data
Voltage:
115 Volts AC only
Current Input:
5.3 A
Weight:
3.25 lb
Frequency:
60 Hz
Power Input:
600 W
No Load Speed:
11,000 rpm
Max. Blade Diameter:

4-1/2" (abrasive, wire brush or diamond)
Removing rust and scale for metal
surface preparation is quickly
accomplished with the HG 450 and
Hilti wire brushes.
Spindle Thread:
HG 450 Accessories
Item No.
Description
00005240
HG 450
Slide action, locking
on/of switch
00005467
HG 450 DLX
5/8"11
Two wire power supply cord:
Operator Comfort
7' length
Item No.
Description
00005315
00253713
00005313
00004302
Safety Guard
Flange Kit
Spanner Wrench
Kit Box (Metal)
The dead man switch is designed

not only to quickly switch off the Hilti
500-D when the operator lets go,
but it also lends the new angle
grinder with paddle switch a more
convenient design for greater
working comfort.
HG 450 with metal kit

box
00005676
HG 450D
Slide action, constant
pressure on/off switch
00005120
HG 450D DLX
HG 450 D with metal
kit box
4 1/2" Blade Guard
Inner Flange
Wire Brush Cup Wheels

(Knotted or Crimped)
(5/8"11 arbor)
115 volts AC only
Current Input:
8.5 A
Weight
4.1 lb
Frequency
60 HZ
High Performance and

Long Life Expectancy
Power Input
Thanks to the larger blade diameter,

5" grinders remove more material
for a longer period of time without
the blade having to be changed.
The additional dust-resistant
enclosure of the powerful 8.5 amp
motor and housing result in the long
service life.
No Load Speed
900 W
11,000 rpm
Max. Blade Diameter

5" (abrasive, wire brush or diamond)
Spindle Thread
5/8" 11
Two wire power supply cord

7' length
Outer Flange
Type 27
Abrasive Wheels
(7/8" arbor)
Wire Brush Flat Wheels

(Stringer Bead or Full Cable)
(5/8"11 arbor)
Technical Data
Voltage:
Item No.
Description
00373608
HG 500-D
DC 500-D Accessories
Item No.
Description
00258282
00244063
00244034
00334782
00257735
Plastic Kit Box

Flange Kit for DC/HG 500
Kwik-Lock Blade Guard DC 500S
Cutting Guard with Foot
Grinding Guard
Warning:
Dry Diamond
Cup Wheels
3.49
Abrasive blades should only be used

on angle grinders equipped with
blade guards specially designed for
the blade being used.
Grinding Systems
DC 500-S
DC 700-S
Technical Data
Voltage:
Technical Data
Voltage:
120 Volts AC only
120 Volts AC only
Current Input:
Current Input:
12 A
15 A
Weight
Weight
4.1 lb
9.25 lb
Frequency
Frequency
60 Hz
60 Hz
Power Input
Power Input
1400 W
2000 W
No Load Speed
No Load Speed
11,000 rpm
8,500 rpm
Max. Blade Diameter
Max. Blade Diameter
5" (abrasive, wire brush or diamond)

Using Hilti diamond grinding wheels
with the new DC 500-S provide cost
efficiency in time and material when
finishing concrete.
Spindle Thread
5/8"11

7' length
00310020
Description
Item No.
Description
00337031
DC 700-S
DC 500-S
DC 700 Accessories
With constant-on button
Item No.
Description
00005380
00005396
00005397
00005395
Blade Guard 7"

Flange Nut
Flange
HG Flange Kit
DC 500-S Accessories
Item No.
Description
00258282
00244063
00244034
00244062
00334782
00257735
Plastic Kit Box

Flange Kit for DC/HG 500
Kwik-Lock Blade Guard DC 500S
Depth Guard
Cutting Guard with Foot
Grinding Guard
Inner Flange
5/8"11

7' length
1 Flange Nut, 1 Spanner Wrench and 1 Flange
00005399
Spanner Wrench
7" Blade Guard
5" Kwik-Lock Blade Guard
Spindle Thread
Item No.
7" (abrasive, wire brush or diamond

cup wheel)
With Hilti premium abrasives, the

DC 700-S grinder is suited for weld
grinding and metal preparation.
Flange Nut
Flange
Type 27
Abrasive Wheels
(7/8" arbor)
Outer Flange
Type 27
Abrasive Wheels
(7/8" arbor)

(5/8"11 arbor)
Type 27
Abrasive Wheels
(5/8"11 arbor)
Dry Diamond
Cup Wheels

(5/8"11 arbor)
Warning:
Dry Diamond
Cup Wheels
Abrasive blades should only be used

on angle grinders equipped with
blade guards specially designed for
the blade being used.

(5/8"11 arbor)

(5/8"11 arbor)
www.us.hilti.com
3.50
Abrasive Blades
Hilti Resin-Bonded Abrasive Wheel Program

Formulated To Meet The Needs Of The Professional
The Hilti selection of grinding abrasive discs and cut-off wheels
are formulated to meet the rigors of grinding, cutting and
finishing required by the professional user. All of the premium
products in this line have met the quality testing required for Hilti
products. This high quality translates into high performance
minimizing work time and maximizing tool efficiency.
Hilti reinforced resin bonded abrasives offer:
Select abrasive particles of silicon carbide or aluminum oxide
to provide aggressive grinding/cutting with minimal equipment
heat-up translating into longer tool life.
Double or triple reinforcement contains the abrasive mixture
prolonging blade life while adding a high measure of safety
to the product.
Product consistency as a result of close tolerance
manufacturing
A wide variety of formulations and dimensions available
engineered to meet the requirements of professionals for
cutting or grinding applications
Abrasive material removed to show fiberglass reinforcement mats.
Abrasive Wheel Nomenclature

Nomenclature for Hilti abrasive products reflects the wheel application. Thickness and bond of each wheel is matched
to its specific application.
AB-C 1 G-7X1/4X5/8-11
Blade dimensions
Diameter x Thickness x Arbor configuration
Designates blade type
Abrasive Blade (AB) as opposed to Diamond
Blade (DB)
= 5/8" 11 arbor
= 7/8" arbor
Designates blade composition

C = Silicon Carbide
A = Aluminum Oxide
Z = Zirconium
Equipment type
G = grinder
H = hand-held
M = masonry
P = portable track saw
R = road saw
S = stationary track saw
RC = rail cutting saw
Designates bond. Refer to the Specification
Code chart adjacent to each product group.
www.us.hilti.com
3.51
Abrasive Blades
Premium Type 27 Abrasives Metal

Type 27 abrasive wheels are designed with a depressed center flange for use in hand held angle grinders. Formulated
to be used for grinding, Type 27 wheels perform best when used at a 1530 degree angle to flat surfaces.
Specification Codes: Type 27 Metal
A2G
Specifically formulated for the non-loading grinding of aluminum, brass/bronze and
non-ferrous metals
A4G
Fast cutting blades for grinding stainless steel and other hard materials. Meets nuclear industry
standards for nuclear construction and maintenance.
A6G
Long life blade for grinding pipeline welds
A8G
Specially formulated blades for grinding cast iron, cast steels and foundry materials
A10G
General purpose, fast cut blades for grinding in a wide range of metal applications,
including harder metal materials
5/8" 11 arbor
A12G
General purpose long life blades formulated for grinding welds and surface conditions
A14G
General purpose cut-off blades for metal applications
= 7/8" arbor
= 5/8" 11 arbor
Type 27 Abrasives - Metal, Pipeline Welds

Item No.
Description
Application
Material
Max rpm
Box Qty
00087796
00053816
00053810
00339495
98555571
00053808
00087797
00087798
00223897
00053647
00053930
AB-10G - 4 x 14 x 58"
AB-A2G - 4-12 x 14 x 78
AB-A4G - 4-12 x 14 x 78
AB-A4G - 4-1/2 x 1/8 x 5/8-11
AB-A4G - 4-1/2 x 1/4 x 5/8-11
AB-A8G - 4-12 x 14 x 78
AB-A10G - 4-12 x 18 x 78
AB-A10G - 4-12 x 14 x 78
AB-A10G - 4-12 x 14 x 58-11
AB-A12G - 4-12 x 14 x 78
AB-A14G - 4-12 x 18 x 78
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Cutting
Steel
Aluminum
S. Steel
S. Steel
S. Steel
Cast
Steel
Steel
Steel
Steel
Metal
15,000
13,300
13,300
13,300
13,300
13,300
13,300
13,300
13,300
13,300
13,300
25
10
25
25
25
25
25
25
10
25
25
00253480
00253481
00253482
00053817
00253485
00253486
00253487
00253488
AB-A2G - 5 x 1/4 x 7/8

AB-A4G - 5 x 1/4 x 7/8
AB-A8G - 5 x 1/4 x 7/8
AB-A10G - 5 x 1/4 x 7/8
AB-A10G - 5 x 1/8 x 7/8
AB-A10G - 5 x 1/4 x 5/8-11
AB-A12G -5 x 1/4 x 7/8
AB-A14G -5 x 1/8 x 7/8
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Grinding
Cutting
Aluminum
S. Steel
Cast
Steel
Steel
Steel
Steel
Steel
11,000
11,000
11,000
11,000
11,000
11,000
11,000
11,000
10
25
25
25
25
10
25
25
00087800
98555573
00053827
00053819
00053821
00053941
AB-A4G - 7 x 14 x 58-11
AB-A4G - 7 x 1/8 x 5/8-11
AB-A10G - 7 x 14 x 58-11
AB-A12G - 7 x 14 x 78
AB-A12G - 7 x 14 x 58-11
AB-A14G - 7 x 18 x 58-11
Grinding
Grinding
Grinding
Grinding
Grinding
Cutting
S. Steel
S. Steel
Steel
Steel
Steel
Metal
8,600
8,600
8,600
8,600
8,600
8,600
25
25
10
25
25
25
00053838
AB-A12G - 9 x 14 x 58-11
Grinding
Steel
6,800
25
Pipeline Welds
98560042
00053887
98560043
00253490
AB-A6G 4-1/2 x 1/8 x 5/8-11

AB-A6G - 4-12 x 316 x 78
AB-A6G 4-1/2 x 1/4 x 5/8-11
AB-A6G - 5 x 316 x 78
Grinding
Grinding
Grinding
Grinding
S. Steel
Pipeline Weld
Steel
Pipeline Weld
13,300
13,300
13,300
11,000
25
25
25
25
Grinding
Grinding
Pipeline Weld
Steel
8,600
8,600
25
25
7/8" arbor
Use Wire Brush - 4CS Stringer Bead, Item #00041364 with the above discs.
00025921
98555572
AB-A6G - 7 x 18 x 58-11
AB-A6G 7 x 1/4 x 5/8-11
www.us.hilti.com
3.52
Abrasive Blades
Premium Type 27 Abrasives for Concrete

Specification Codes for Type 27 Concrete
Feature
and or bullets
C1G text General
purpose blades for the grinding of concrete, stone and masonry materials.
C3G
General purpose blades for the cutting of concrete, stone and masonry materials.
Type 27 Abrasives - Concrete/Masonry Grinding

= 5/8" 11 arbor
= 7/8" arbor
Item No.
Description
Application
Material
Max rpm
Box Qty
00025919
00253492
00025925
AB-C1G - 4-12 x 14 x 78
AB-C1G - 5 x 14 x 78
AB-C1G - 7 x 14 x 58-11
Grinding
Grinding
Grinding
Concrete
Concrete
Concrete
13,300
11,000
8,600
25
25
25
Type 27 Abrasives - Concrete/Masonry Cutting

= 5/8" 11 arbor
Item No.
00053947
00253494
= 7/8" arbor
Description
AB-C3G - 4-12 x 18 x 78
AB-C3G - 5 x 18 x 78
Application
Cutting
Cutting
Material
Concrete
Concrete
Max rpm
Box Qty
13,300
11,000
25
25
Super Premium Zirconium Abrasive Discs

Rugged, free-cutting grinding performance
Hilti Zirconium abrasive blades typically have a life 3
to 7 times that of ordinary abrasive blades
The operating cost of the Hilti Zirconium blades is
typically less than standard abrasives
Hilti Zirconium blades provide aggressive stock

removal
Best choice for stainless steel
Type 27 Zirconium Abrasives - Metal Grinding

Item No.
Description
Application
Material
Max rpm
Box Qty
00033945
00033950
00253496
AB-Z-4-12 x 14 x 78
AB-Z-4-12 x 14 x 58-11
AB-Z-5 x 14 x 58-11
Grinding
Grinding
Grinding
Metal
Metal
Metal
13,300
13,300
11,000
10
10
10
00033951
AB-Z-7 x 14 x 78
Grinding
Metal
13,300
10
00033955
AB-Z-7 x 14 x 58-11
Grinding
Metal
13,300
10
www.us.hilti.com
3.53
Abrasive Blades

Alumina Zirconia Flap Discs 5/8" 11 Arbor
Features
Applications
Base Material
One step grind

and finish
10-15 times the life of
conventional fibre discs
Integrated backer, no separate
pad required
Best suited for:

Stainless steel
Carbon steel
Plastic
Fiberglass
Wood
Deburring
Edge grinding
Rust and paint removal
Surface conditioning and
preparation
Specification Codes: Resin Fibre Flap Disc

36
Coarse surface finish, heavy metal removal
60
Medium surface finish, some metal removal
80
Fine surface finish, little metal removal
120
Very fine surface finish, no metal removal
Item No.
Description
Diameter
Grit Size
Arbor
Max rpm
00252368
00252370
00252371
00252372
FD-36AZ-4-1/2
FD-60AZ-4-1/2
FD-80AZ-4-1/2
FD-120AZ-4-1/2
4-1/2"
4-1/2"
4-1/2"
4-1/2"
36
60
80
120
5/8" - 11
5/8" - 11
5/8" - 11
5/8" - 11
13,300
13,300
13,300
13,300
Box Qty
5
5
5
5
00252373
00252374
00252375
00252376
FD-36AZ-5
FD-60AZ-5
FD-80AZ-5
FD-120AZ-5
5"
5"
5"
5"
36
60
80
120
5/8" - 11
5/8" - 11
5/8" - 11
5/8" - 11
12,150
12,150
12,150
12,150
5
5
5
5
00252377
00252378
00252382
FD-36AZ-7
FD-60AZ-7
FD-120AZ-7
7"
7"
7"
36
60
120
5/8" - 11
5/8" - 11
5/8" - 11
8,600
8,600
8,600
3
3
3
Premium Thin Cut Off Wheels

Hilti Thin Cut Off Wheels are a premium, double
reinforced wheel with a special bond and protective
coating designed to hold the grains together tightly.
General purpose, designed for fast cutting of metal

products.
Specification Codes: Thin Cut Off Wheels

A8H General purpose, designed for fast cutting of metal products.
Item No.
Description
00253777
00253778
00253779
AB-A8H-412 x 0.040 x 78
AB-A8H-5 x 0.040 x 78
AB-A8H-6 x 0.040 x 78
Application
Material
Max rpm
Box Qty
Cutting
Cutting
Cutting
Metal
Metal
Metal
17,000
15,000
14,200
50
50
50
www.us.hilti.com
3.54
Abrasive Blades
Abrasive Blades for Hand-Held Saws (Type 1)

For use with gas powered, electric or pneumatic saws
Specifications
C1H
C5H
A2H
Asphalt/Green concrete
General purpose blade for cutting
concrete (green or cured), brick, block,
clay pipe, and other masonry materials.
Ductile iron, cast iron, concrete lined metal
sewage pipe. Comprised of Silicon Carbide
and Aluminum Oxide.
A6H
A8H
Super Premium for sheet metal, roof decking,

car dismantling. Also good for general purpose
steel, stainless steel pipe and profiles.
General purpose metal - mild steel and
stainless steel including rebar, pipe, and
structural profiles.
= 20 mm or 1" arbor
Premium
Metal (Type 1)
Item No.
Description
Max rpm
Box Qty
00087806
00025473
00087808
00025784
AB-A8H-12x18x1
AB-A8H-12x18x20mm
AB-A8H-14x18x1
AB-A8H-14x18x20mm
6,300
6,300
5,400
5,400
10
10
10
10
Concrete (Type 1)
00087807
00025317
00087809
00025785
AB-C5H-12x18x1
AB-C5H-12x18x20mm
AB-C5H-14x18x1
AB-C5H-14x18x20mm
6,300
6,300
5,400
5,400
10
10
10
10
Asphalt/Green Concrete (Type 1)

00025850
AB-C1H-12x532x20mm
00025852
AB-C1H-12x532x1"
6,300
6,300
10
10
Ductile Metal (Type 1)

00025846
AB-A2H-12x18x1
00025844
AB-A2H-12x18x20mm
00025849
AB-A2H-14x18x1
00025847
AB-A2H-14x18x20mm
6,300
6,300
5,400
5,400
10
10
10
10
6,300
6,300
5,400
5,400
10
10
10
10
Super Premium
Metal Decking (Type 1)
00041457
AB-A6H-12x532x1
00041455
AB-A6H-12x532x20mm
00041308
AB-A6H-14x532x20mm
00041311
AB-A6H-14x532x1
Abrasive Blades for Rail Track Cutting

Fixed saw cutting only
Specification Code: Abrasive Blades for Rail Track Cutting
Z RC
Rail track cutting for mainline to light gauge rail.
Super Premium
Item No.
Description
Max rpm
Box Qty
00339497
00339498
Rail Pro AB-Z 14" x 1/8" x 1"

Rail Pro AB-Z 16" x 1/8" x 1"
5,400
4,800
10
10
www.us.hilti.com
3.55
Abrasive Blades
Premium Abrasive Blades

for Walk Behind Saws (Type 1)
18 HP or less
Specifications
C1R
C5R
Asphalt/Green Concrete
Cured concrete. Best performance on low HP equipment.
= 1" arbor with drive pin hole

Cured Concrete
Item No.
Description
Max rpm
Box Qty
00087814
00087816
AB-C5R-14x316x1
AB-C5R-14x14x1
4,365
4,365
10
10
Asphalt/Green Concrete
00087815
AB-C1R-14x316x1
00087817
AB-C1R-14x14x1
4,365
4,365
10
10
Premium Abrasive Blades for Circular Saws (Type 1)

Specifications
C1
A6
General purpose-concrete, stone, masonry, non-ferrous metals, aluminum and cast iron.
General purpose applications for steel and other ferrous metals. Good balance of speed to life.
= DM = 5/8" arbor with diamond-shaped knockout
Metal - Alum. Oxide Wheel

Item No.
Description
Max rpm
Box Qty
00087802
00087804
AB-A6-7x332xDM
AB-A6-8x332xDM
8,600
7,500
25
25
Concrete - Silicon Carbide Wheel

Item No.
Description
Max rpm
Box Qty
00087803
AB-CI-7x18xDM
8,600
25
www.us.hilti.com
3.56
Abrasive Blades
Abrasive Blades for Track Saws (Type 1)

Specification Codes: Type 1-Portable Saws
A4P
For dry wall track. Good balance of speed and life.
(Recommended for use on 18 to 26 gauge drywall track.)
A6P
General purpose metal: dry wall track, angle iron, rebar, light tubing.
= 1" arbor
Premium Track Saw Blade (Type 1)

Item No.
Description
Max rpm
Box Qty
00087810
00087811
AB-A4P - 12 x 332 x 1
AB-A4P - 14 x 332 x 1
5,092
4,365
10
10
Super Premium Track Saw Blade (Type 1)

Item No.
Description
Max rpm
Box Qty
00025839
00025916
00025917
AB-A6P - 12 x 332 x 1
AB-A6P - 14 x 332 x 1
AB-A6P - 16 x 332 x 1
5,092
4,365
3,820
10
10
10
www.us.hilti.com
3.57
Wire Brushes
Premium Wire Brush Program

W. Brush-4 CS - Full Cable
Material
CS = Carbon Steel
SS = Stainless Steel
Brush Diameter
Application
Deburring
Wire Brush
Knotted Cup
Wire Brush
Crimped Cup
Fine
Coarse
Edge Blending
Weld, Scale Removal
Stringer Bead Weld Prep
Surface Finishing
Rust Oxide Removal
Fine
Coarse
Paint Removal
Roughening
Cleaning
Flash Removal
Tool Mark Removal
Expansion Joint
Narrow Groove Cleaning
Wire Brush
Nomenclature Guide
Brush Type
See application guide
Wire Brush
Full Cable
Wire Brush
Stringer Bead
Wire Brush
Selection Guide
Knotted Cup
Use brushes for cleaning welds, and for operating in tight places such as corners, angle welds and T-connections.
Item No.
Description
00041362
00041367
00053733
98570037
Wire Brush-3CS Knotted Cup

Wire Brush-3SS Knotted Cup*
Wire Brush-4CS Knotted Cup
Wire Brush-4CS 24 Knot Wheel
Spindle
Max rpm
Wire Size
inches
Box Qty
5/8"11
5/8"11
5/8"11
3/8"24
12,500
12,500
8,000
8,000
.020
.020SS
.020
.014
6
6
2
5
Wire Size
inches
Box Qty
Crimped Cup
Designed for light duty jobs. Fast brushing action quickly removes light rust and oxides.
Good choice for flat surface
Item No.
Description
00041363
00053736
Wire Brush-3CS Crimped Cup

Wire Brush-4CS Crimped Cup
Spindle
Max rpm
5/8"11
5/8"11
12,500
8,000
.0118
.014
6
2
Full-Cable Twist
Constructed for heavy duty work. Made with larger knots than stringer bead wire brushes.
Good choice for high-volume work.
Item No.
Description
00041365
Wire Brush-4CS Full Cable
Spindle
Max rpm
5/8"11
20,000
Wire Size
inches
Box Qty
.020
Stringer Bead
Excellent for stringer bead weld cleaning and other applications where a narrow brush is necessary.
Item No.
Description
98570033
00041364
98570035
00041366
98570036
98570034
Stringer Bead-4CS Knot Wheel

Wire Brush-4CS Stringer Bead
Stringer Bead-4SS Knot Wheel
Wire Brush-4SS Stringer Bead*
Stringer Bead-6SS Knot Wheel
Stringer Bead 6SS Knot Wheel
Spindle
5/8"11
5/8"11
5/8"11
5/8"11
5/8"11
5/8"11
Wire Size
inches
Max rpm
Box Qty
.020
.020
.020
.020
.020
.020
20,000
20,000
6
6
6
6
6
6
Assortment Kit
Item No.
Description
00054106
HG-450 Mini Grinder Brush Assortment
Spindle
Box Qty
5/8-11
Assortment includes 1 each: Wire Brush-3CS Knotted Cup, Wire Brush-3CS Crimped Cup,
Wire Brush-4CS Stringer Bead,Wire Brush-4CS Full Cable)
Walk Behind Wire Brush

Item No.
Description
00067477
Wire Brush-FW-12 x .375 x 1
Spindle
Max rpm
Box Qty
1"
4,500
Includes 1" arbor with drive pin hole.

* Stainless steel brushes are made of 302 grade stainless steel wire. Stainless steel is typically used to brush stainless steel, high strength alloys and
aluminum.
www.us.hilti.com
3.58

Saw Blades
e
Just in th-PE
0
0
9
WSR ating
Reciproc .
Saw
viii
e
e
S Pageils.
ta
e
d
for
Saw Blade Selector Guide
Page 4.3
Carbide-Tipped Saw Blades
Page 4.3
Reciprocating Saw Blades
Page 4.4
Band Saw Blades, Bi-Metal
Page 4.4
Hack Saw Blades, Bi-Metal
Page 4.4
Metal Twist Drill Bits

Drill Bit Selector Guide
Page 4.5
Jobber Fractional Heavy Duty Drill Bits
Page 4.6
Jobber Fractional Cobalt Drill Bits
Page 4.7
Jobber Titanium Coated Drill Bits
Page 4.8
Silver And Deming
Page 4.8
Fractional Screw Machine Stubby Bit
Page 4.9
Stepper Bits
Page 4.11
Bi-Metal Hole Saws And Arbors
Page 4.13
Specialty Bits
Aircraft Style HSS Drill Bits
Page 4.10
Bell Hanger Drill Bits
Page 4.10
Wood Bits
Spade Bits
Page 4.12
Ship Auger Bits
Page 4.12
Saw Tooth Multispur Wood Drill Bits
Page 4.12
Annular Cutters
Page 4.14
Saw Blade Selector Guide
Carbide Tipped Saw Blades

Contractor Carbide Tipped Blades (CC Series)
Specification
CC - Contractor Carbide
Carbide tipped, general purpose blades designed to stay sharp

up to 25 times longer than regular steel blades.
Carbide blade for the contractor.
= ATB
Item No.
Description (diameter, bore, teeth)
00372178
00372179
00372180
00372181
00372182
00372183
00372184
00372185
SB-CS 7 1/4 X 5/8 X 13/16 20T

SB-CS 7 1/4 X 5/8 X 13/16 20T
SB-CS 7 1/4 X 5/8 X 13/16 20T
SB-CS 7 1/4 X 5/8 X 13/16 24T
SB-CS 7 1/4 X 5/8 X 13/16 24T
SB-CS 7 1/4 X 5/8 X 13/16 24T
SB-CS 7 1/4 X 5/8 X 13/16 40T
SB-CS 7 1/4 X 5/8 X 13/16 40T
Kerf
Grind
Hook
Angle
Max RPM
0.084"
0.084"
0.084"
0.084"
0.084"
0.084"
0.084"
0.084"
ATB
ATB
ATB
ATB
ATB
ATB
ATB
ATB
20
20
20
20
20
20
20
20
9000
9000
9000
9000
9000
9000
9000
9000
Application
General Purpose: rip or cutoff

Rip or cross cut
Rip or cross cut
Rip or cross cut
Cross cut: excellent finish
Cross cut: excellent finish
Qty
2
25
100
2
25
100
2
25
Kwik-Pro Fused Teeth CS Series Durable Fast wood blades-thin kerf

Item No.
Description (diameter, bore, teeth)
96000563
96000564
96000566
96000568
SB-CS 8-1/4 x 5/8 x 13/16 24T

SB-CS 8 1/4 x 5/8 x 13/16 40T
SB-CS 10 x 5/8 x 40T
SB-CS 10 x 5/8 x 60T
Kerf
Grind
Hook
Angle
Max RPM
0.084"
0.084"
0.094"
0.094"
ATB
ATB
ATB
ATB
20
20
13
10
7900
7900
6500
6500
Application
Qty
Heavy Duty Rip or Cross Cut

Heavy Duty Cross Cut - Excellent Finish
Good Finish Cutoff All Wood
Cutoff Excellent Cut for Wood
2
2
2
2
Special Purpose Saw Blades (HDC Series)

Fire and Rescue Blade
Specification
HDC - Heavy Duty Contractor
Used by Fire Dept. & Rescue Teams for lifesaving

Use on gas powered portable machines
To be used only by trained personnel wearing appropriate protective equipment
Semi-industrial blade for the

professional.
= NCG
Item No.
Description
(diameter, bore, teeth)
Grind
96002438
96002440
SB-HDC-12x1x12T
SB-HDC-12x20mmx12T
NCG
NCG
Hook
Angle
Max
rpm
Application
Qty
15 5,500 Fire & Rescue

15 5,500 Fire & Rescue
Number of Teeth in the Cut
Selection Tips
Selecting the proper saw blade for your application is
critical for achieving maximum tool performance.
For further assistance, please contact Hilti
Customer Service at 1-800-879-8000.
1. All saw blades are designed to reach beyond the
thickness of the material being cut about 5/8".
2. General Rule:
Fewer teeth on thick material
More teeth on thin material
Fewer teeth on green (wet) material
More teeth on dry material
3. Carbide typically stays sharp from 25 to 50 times

longer than steel.
4. Maximum rim speed of blade, 18,000 SFPM SFPM =
Surface feet per minute
5. Carbide needed on man-made material for longer life
6. Two to four teeth should be in the material at all times
(see diagram at right).
RIGHT
WRONG
Top Grinds
ATB
Alternate Top Bevel

For crosscutting, cut-off and
trimming.
NCG
Nail Cutting Grind

Modified grind for rough
applications.
RIGHT
www.us.hilti.com
4.3
1
1
Bi-Metal Reciprocating Saw Blades

General Guidelines:
Harder/thinner base material =
finer pitch teeth
No less than two teeth in
contact with work surface.
Example:
Band Saw Blades, Bi-Metal

Box Item No.
Description
96257902
96257903
96257904
Band Saw Blade 44 7/8 X .020 X 14T

Box Qty
12
12
12
Hack Saw Blades, Bi-Metal
1/8" material = 16 teeth per inch

minimum (2 teeth every 1/8")
Bi-Metal:
Thicker steel body for strength

Medium grade alloy steel body for flexibility
Teeth - M3 steel
Teeth electron beam welded to body
Metal cutting (0.035" Blade for ductile metal, plastics)

Item No.
Description
00205993
00205995
00205996
00253241
00205997
00253242
00205998
00253243
00205999
00253244
00206315
00253245
00374336
00374337
R-MB 4" X 18T SHORT METAL CUTTING

R-MB 6" X 10T HD METAL CUTTING
R-MB 8" X 18T METAL CUTTING
R-MB 12" X 18T METAL CUTTING
Box Qty
5
5
5
50
5
50
5
50
5
50
5
50
5
5
Wood/Nail
(0.05" Blade - sloped for tight access and progressive strength)
Item No.
Description
00205989
00253236
00205990
00253237
00205991
00253238
R-NB 6" X 6T WOOD & NAIL

Box Qty
5
50
5
50
5
50
Item No.
Description
96257900
96257901
12" X 24T Bi-Metal Hand Hack Blade

12" X 32T Bi-Metal Hand Hack Blade
Box Qty
100
100
96257905
Hi-Tension 12" Hack Saw Frame with

24T Blade
e
Just in th-PE
WSR 900ating
Reciproc .
Saw
viii
See Pageils.
for deta
Combination (0.05" Blade - metal, composites)

Item No.
Description
00374338
00374339
00374340
R-CB 6X10/14 COMBINATION

Box Qty
5
5
5
Demolition (0.062" Ultra thick blade-heavy materials)

Item No.
Description
00374341
R-DB 9X6 DEMOLITION
Box Qty
Drywall/Plaster (0.035" Blade- bi-directional V-Tooth Fast Cut)

Item No.
Description
00374342
R-PB 6X6 DRYWALL/PLASTER
Box Qty
www.us.hilti.com
4.4
Drill Bit Selector Guide

Selecting the proper drill bit for your application is critical for achieving maximum tool
performance. Hilti provides a broad range of drill bit diameters for use with a wide variety
of base materials. The selector guide below has been developed and organized to help you
choose the correct Hilti Wood Systems drill bit.
For further assistance, please contact Hilti Customer Service at 1-800-879-8000.
Suggested Hilti Drill Bits By Material Type
Material
Carbon Steel
Ductile Brass
Carbon Steel
Aluminum
Stainless Steel
Cast Iron
Hard Steel
Heat Treated Alloys
Wood
Drill Style
General
Purpose
Titanium
Angle
Point
118 point
Operator
Applied
Pressure*
M-H
135 split point
M-H
Cobalt
135 split point
M-H
Cobalt
135 split point
Heavy
N/A
N/A
N/A
N/A
M-H
M-H
M-H
M-H
Spade
Ship Auger
Holesaw
Stepper
*M-H: medium to heavy
Coolant or
Lubricant
oil or
water solution
oil or
activated solution
oil or
activated solution
oil or
activated solution
N/A
N/A
N/A
N/A
Bit Style Reference

118
Standard point for general purpose

applications
135
Split point for hard, tough materials;

designed to self-center
Black Oxide
Provides additional tempering and stress

relief to high speed twist drills
Cobalt
Use for drilling tough materials such as

stainless steel, titanium, or heat treated
steel with 135 split point for fast and
accurate starting
Hole Saw
For cutting holes 9/16" to 6".

Must be mounted to an arbor.
Jobber Length
Used for drilling deep holes
Screw Machine Length Also known as stubby, main use

drilling in materials such as sheet metal
Ship Auger
Screw point bit used for heavy timber

such as railroad ties or creosoted poles
Silver and Deming
Generic term for drills from 17/32" to

1-1/2" with 1/2" shank; 118 point with
black oxide coating
Spade
Wing Tip style bit use for boring

medium-sized holes in wood
Stepper
Incrementally flared bit used to widen

existing holes with consistent precision
Titanium
Titanium nitride improves drill life by

acting as wear-resistant, thermal barrier
between high speed twist drill and
material being drilled. These bits typically
have 135 split point for fast and
accurate starting
www.us.hilti.com
4.5
Fractional Heavy Duty Jobber Drill Bits

135 Degree Split Point
Features
Applications
Medium Alloyed Materials

Medium Alloyed Steel
Stainless Steel
Jobber Length
Straight Shanks
Thicker Web to provide extra strength and rigidity
Ground Flute suitable for medium alloyed steel and
stainless steel
Special aerospace 135 split point for self centering (no
center punching necessary)
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
Flute
Length (in.)
96053745
96053746
96053747
96041328
96041329
96053748
96053749
96053754
96041330
96053756
96053757
96053758
96041331
96086907
96086908
96086909
96041332
96086911
96086912
96086913
96041333
96086915
96086916
96086917
96053759
96086919
96086920
96086921
96041334
Bit HSS Jobbers 1/16

Bit HSS Jobbers 1/8
Bit HSS Jobbers 1/4
Bit HSS Jobbers 3/8
Bit HSS Jobbers 1/2
0.0625
0.0781
0.0938
0.1094
0.1250
0.1406
0.1563
0.1719
0.1875
0.2031
0.2188
0.2344
0.2500
0.2656
0.2812
0.2969
0.3125
0.3281
0.3438
0.3594
0.3750
0.3906
0.4062
0.4219
0.4375
0.4531
0.4688
0.4844
0.5000
1-7/8"
2"
2-1/4"
2-5/8"
2-3/4"
2-7/8"
3-1/8"
3-1/4"
3-1/2"
3-5/8"
3-3/4"
3-7/8"
4"
4-1/8"
4-1/4"
4-3/8"
4-1/2"
4-5/8"
4-3/4"
4-7/8"
5"
5-1/8"
5-1/4"
5-3/8"
5-1/2"
5-5/8"
5-3/4"
5-7/8"
6"
Bit Sets
96002421
HSS 13 Piece Set 1/16" to 1/4"
13
96087090
BIT 29 Piece Set 1/16" to 1/2"
29
7/8"
1"
1-1/4"
1-1/2"
1-5/8"
1-3/4"
2-1/8"
2-1/3"
2-5/16"
2-7/16"
2-1/2"
2-5/8"
2-3/4"
2-7/8"
2-15/16"
3-1/16"
3-3/16"
3-5/16"
3-7/16"
3-1/2"
3-5/8"
3-3/4"
3-7/8"
3-15/16"
4-1/16"
4-3/16"
4-5/16"
4-3/8"
4-1/2"
Box
Qty
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
6
6
6
6
6
6
6
6
6
6
6
www.us.hilti.com
4.6
Fractional Cobalt Jobber Drill Bits

Features
Applications
Jobber Length
Straight Shanks
Thicker Web to provide extra strength and rigidity
Ground Flute suitable for medium alloyed steel
and stainless steel
Special aerospace 135 split point for self centering
(no center punching necessary)
Stainless Steel
Hardened grades of Stainless Steel
High Temperature Alloys
Heat Treated Materials
Plastic Abrasives
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
96205122
96205123
96205124
96205125
96205126
96205127
96205128
96205129
96205130
96205131
96205132
96205133
96205134
96205135
96205136
96205137
96205138
96205139
96205140
96205141
96205142
96205143
96205144
96205145
96205146
96205147
96205148
96205149
96205150
Sets
Fractional Cobalt Jobber 1/16

0.0625
0.0781
0.0938
0.1094
0.1250
0.1406
0.1563
0.1719
0.1875
0.2031
0.2188
0.2344
0.2500
0.2656
0.2812
0.2969
0.3125
0.3281
0.3438
0.3594
0.3750
0.3906
0.4062
0.4219
0.4375
0.4531
0.4688
0.4844
0.5000
1-7/8"
2"
2-1/4"
2-5/8"
2-3/4"
2-7/8"
3-1/8"
3-1/4"
3-1/2"
3-5/8"
3-3/4"
3-7/8"
4"
4-1/8"
4-1/4"
4-3/8"
4-1/2"
4-5/8"
4-3/4"
4-7/8"
5"
5-1/8"
5-1/4"
5-3/8"
5-1/2"
5-5/8"
5-3/4"
5-7/8"
6"
Item No.
Description
96205184
13 Piece Set Fractional Cobalt Jobbers
Flute
Length (in.)
7/8"
1"
1-1/4"
1-1/2"
1-5/8"
1-3/4"
2"
2-1/8"
5-5/16"
2-7/16"
2-1/2"
2-5/8"
2-3/4"
2-7/8"
2-15/16"
3-1/16"
3-3/16"
3-5/16"
3-7/16"
3-1/2"
3-5/8"
3-3/4"
3-7/8"
3-15/16"
4-1/16"
4-3/16"
4-5/16"
4-3/8"
4-1/2"
Shown below
Box
Qty
2
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
6
6
6
6
6
6
6
6
6
6
6
Box Qty
13
15
29
not shown
29
Set includes: 1/16" to 1/4" in 1/64" increments
96205185

96205186

96205187
29 Piece 3/8 Shank Fractional Cobalt Jobbers

Set includes: 1/16" to 1/2"
www.us.hilti.com
4.7
Titanium Coated Jobber Drill Bits

Features
Ground flute suitable for

tool steel
Jobber length
alloys
Straight shank
stainless steel
cast iron
hard to machine materials
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
96205151
96205153
96205155
96205157
96205159
96205161
96205163
96205165
96205167
96205169
96205171
96205173
96205175
96205177
96205179
Titanium Coated Jobber 1/16

0.0625
0.0938
0.1250
0.1563
0.1875
0.2188
0.2500
0.2812
0.3125
0.3438
0.3750
0.4062
0.4375
0.4688
0.5000
1-7/8"
2-1/4"
2-3/4"
3-1/8"
3-1/2"
3-3/4"
4"
4-1/4"
4-1/2"
4-3/4"
5"
5-1/4"
5-1/2"
5-3/4"
6"
Flute
Length (in.)
7/8"
1-1/4"
1-5/8"
2"
5-5/16"
2-1/2"
2-3/4"
2-15/16"
3-3/16"
3-7/16"
3-5/8"
3-7/8"
4-1/16"
4-5/16"
4-1/2"
Box
Qty
12
12
12
12
12
12
12
12
12
6
6
6
6
6
6
Silver And Deming

1/2" Reduced Shank 118 Degree Point
Features
Suitable Base Materials
6" length
Cast Iron
Steel
Steel Forging
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
Flute
Length (in.)
Box
Qty
96087072
96087073
96087074
96087075
96087076
96087077
96087078
96087079
96087080
96087081
96087082
96087083
96087084
96087085
96087086
96087087
96087088
96087089
Bit HSS S&D 17/32

Bit HSS S&D 9/16
Bit HSS S&D 19/32
Bit HSS S&D 5/8
Bit HSS S&D 21/32
Bit HSS S&D 11/16
Bit HSS S&D 23/32
Bit HSS S&D 3/4
Bit HSS S&D 25/32
Bit HSS S&D 13/16
Bit HSS S&D 27/32
Bit HSS S&D 7/8
Bit HSS S&D 29/32
Bit HSS S&D 15/16
Bit HSS S&D 31/32
Bit HSS S&D 1
Bit HSS S&D 1 1/8
Bit HSS S&D 1 1/4
0.5312
0.5625
0.5938
0.6250
0.6562
0.6875
0.7188
0.7500
0.7812
0.8125
0.8438
0.8750
0.9062
0.9375
0.9688
1.0000
1.1250
1.2500
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
6"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
www.us.hilti.com
4.8
Fractional Screw Machine Stubby Bit

Features
Applications
Heavy duty black oxide finish

Short flute for exceptional strength
Thicker web to provide extra strength and rigidity
Ground flute suitable for medium alloyed steel and stainless steel
Stainless steel
Medium alloy steel
Sheet metal
All types of automotive work
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
96086989
96086990
96086991
96086992
96086993
96086994
96086995
96086996
96086997
96086998
96086999
96087000
96087001
96087002
96087003
96087004
96087005
96087006
96087007
96087008
96087009
96087010
96087011
96087012
96087013
96087014
96087015
96087016
96087017
Bit HSS SCR MAC 1/16

Bit HSS SCR MAC 1/8
Bit HSS SCR MAC 1/4
Bit HSS SCR MAC 3/8
Bit HSS SCR MAC 1/2
0.0625
0.0781
0.0938
0.1094
0.1250
0.1406
0.1563
0.1719
0.1875
0.2031
0.2188
0.2344
0.2500
0.2656
0.2812
0.2969
0.3125
0.3281
0.3438
0.3594
0.3750
0.3906
0.4062
0.4219
0.4375
0.4531
0.4688
0.4844
0.5000
1-5/8"
1-1/16"
1-3/4"
1-13/16"
1-7/8"
1-15/16"
2-1/16"
2-1/8"
2-3/16"
2-1/4"
2-3/8"
2-7/16"
2-1/2"
2-5/8"
2-11/16"
2-3/4"
2-13/16"
2-15/16"
3"
3-1/16"
3-1/8"
3-1/4"
3-5/16"
3-3/8"
3-7/16"
3-9/16"
3-5/8"
3-11/16"
3-3/4"
Wire Size Drill Bits

Flute
Length (in.)
5/8"
11/16"
3/4"
13/16"
7/8"
15/16"
1"
1-1/16"
1-1/8"
1-3/16"
1-1/4"
1-5/16"
1-3/8"
1-7/16"
1-1/2"
1-9/16"
1-5/8"
1-11/16"
1-11/16"
1-3/4"
1-13/16"
1-7/8"
1-15/16"
2"
2-1/16"
2-1/8"
2-1/8"
2-3/16"
2-1/4"
Features
Wire gauge
Straight shank
Black finish
Cast iron
Steel
Steel forging
Box
Qty
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
6
6
6
6
6
6
6
6
6
6
6
Item No.
Description
Decimal
Equiv. (in.)
Overall Bit
Length (in.)
96257843
96257844
96257849
96257852
96257853
96257862
96257863
96257864
96257871
96257872
Wire Size 1
Wire Size 2
Wire Size 7
Wire Size 10
Wire Size 11
Wire Size 20
Wire Size 21
Wire Size 22
Wire Size 29
Wire Size 30
0.2280
0.2210
0.2010
0.1935
0.1910
0.1310
0.1590
0.1570
0.1320
0.1285
3-7/8"
3-7/8"
3-5/8"
3-5/8"
3-1/2"
3-1/4"
3-1/4"
3-1/8"
1-3/4"
2-3/4"
96257878
60 PC. Wire Drill Set #1-#60
Flute
Length (in.)
2-5/8"
2-5/8"
2-7/16"
2-7/16"
2-5/16"
2-1/8"
2-1/8"
2"
1-3/4"
1-5/8"
Box
Qty
12
12
12
12
12
12
12
12
12
12
1
www.us.hilti.com
4.9
Aircraft Style HSS Drill Bits
Bell Hanger Drill Bits

Feeler Bits with Fish Hole
Features
Features
Extended shanks for drilling holes in inaccessible areas

Thicker web to provide extra strength and rigidity
Ground flute suitable for medium alloyed steel
and stainless steel
Straight shank to 1/2"

Fish hole in flute for pulling wire
118 point on HSS drills quickly through wood and light to
medium grade steel
Tungsten carbide tip on carbide bell hangers drill in
masonry, brick, block, and wood
Applications
Applications
Medium alloyed materials

Medium alloyed steel
Stainless steel
Drilling through drywall and aluminum stud

Drilling holes for cables and telephone lines
through walls with insulation
Telephone installation
Security systems
Wire and cable applications
Item No.
Description Drill Size
96256925
96256926
96256940
96256927
96256928
96256941
96256929
96256942
96256930
96256943
96256931
96256944
96256932
96256945
96256933
96256946
96256934
96256947
96256935
96256948
96256936
96256949
96256937
96256950
96256938
96256951
96256939
96256952
1/16"
1/8"
1/8"
9/64"
5/32"
5/32"
3/16"
3/16"
7/32"
7/32"
1/4"
1/4"
9/32"
9/32"
5/16"
5/16"
11/32"
11/32"
3/8"
3/8"
13/32"
13/32"
7/16"
7/16"
15/32"
15/32"
1/2"
1/2"
O/A Length
6"
6"
12"
6"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
6"
12"
Flute
Length
7/8"
1-5/8"
1-5/8"
1-3/4"
2"
2"
2-5/16"
2-5/16"
2-1/2"
2-1/2"
2-3/4"
2-3/4"
2-15/16"
2-15/16"
3-3/16"
3-3/16"
3-7/16"
3-7/16"
3-5/8"
3-5/8"
3-7/8"
3-7/8"
4-1/16"
4-1/16"
4-5/16"
4-5/16"
4-1/2"
4-1/2"
Item No.
Description
96256910
96256913
96256916
96256919
96256920
96256921
96256911
96256914
96256917
96256912
96256915
96256918
1/4" x 12" HSS

1/4" x 18" HSS
1/4" x 24" HSS
5/16" x 12" HSS
5/16" x 18" HSS
5/16" x 24" HSS
3/8" x 12" HSS
3/8" x 18" HSS
3/8" x 24" HSS
1/2" x 12" HSS
1/2" x 18" HSS
1/2" x 24" HSS
Pkg Qty
6
6
3
6
6
3
6
6
3
6
6
3
www.us.hilti.com
4.10
Stepper Bits
Accurate control of hole diameter in various materials up to 1/8" thick
Each multi-cone bit drills a range of sizes. The deeper the bit advances, the
larger the diameter of hole drilled.
Multi-cone drill bits enter the material one step at a time allowing the
operator to drill the desired hole diameter using the individual steps as a
guide (a washer may also be used as a simple stop).
Self-starting tip eliminates the need for pilot holes.
Usage applications include the installation of junction and switch boxes, metal
studs, electrical applications, installation of lighting fixtures, auto body work
and various other uses.
Features
Suitable for:
High speed steel

Two flutes
Ferrous and non-ferrous

sheet metal
Wood
Plastic laminates
Maintenance
Electrical contracting
Plumbing
Auto body repair
Heating
Air conditioning
Rust proofing
Recommended Cutting Speeds

1/8" to 3/8"
3/8" to 1/2"
1/2" to 5/8"
5/8" to 3/4"
3/4" to 7/8"
1"
1-1/8"
1-1/2"
1200 rpm
600 rpm
400 rpm
350 rpm
300 rpm
260 rpm
240 rpm
200 rpm
Drilling increments noted below description
Item No.
Description
Drilling Range
96256900
Stepper 13
1/8" to 1/2"
Qty
3/16" to 1/2"
3/16" to 7/8"
1/4" to 3/4"
3/8" to 3/4"
7/16" to 1-1/8"
7/8" to 1-1/8"
7/8" to 1-3/8"
3/4" to 1-3/8"
13 Steps: 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16",11/32", 3/8",13/32", 7/16", 15/32", 1/2"
96256901
Stepper 6
6 Steps: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2"
96256903
Stepper 12
12 Steps: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8"
96256902
Stepper 9
9 Steps: 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4"
96256906
Stepper 3
For drilling 3 standard size holes to accommodate drive screws for knockout punches
3 Steps: 3/8", 7/16", 3/4"
96256904
Stepper 12B
12 Steps: 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1", 1-1/16", 1-1/8"
96256907
Stepper 2
7/8" hole for 1/2" conduit, 1-1/8" hole for 3/4" conduit
2 Steps: 7/8", 1-1/8"
96256975
Stepper 5
1-7/32" hole for oil tight switches
5 Steps: 7/8", 1-1/8", 1-7/32", 1-1/4", 1-3/8"
96256905
Stepper 11
11 Steps: 3/4", 13/16", 7/8", 15/16", 1", 1-1/16", 1-1/8", 1-3/16", 1-1/4", 1-5/16", 1-3/8"
www.us.hilti.com
4.11
Spade Bits
Ship Auger Bits
Features
Features
Cold forged
Machine finished cutting groove
Wing tip design
Precision ground hex shank
Size stamped on blade for easy
identification
Industrial quality
Applications
Applications
Boring holes through any soft

wood
Boring holes through any soft
laminated wood
Saw Tooth Multispur

Wood Drill Bits
Bore Large Deep HolesFast
Will cut Nail embedded wood

12" Twist Length
Heat Treated
Machine ground hollows
Single Twist
Single Cutter
Self Feeding Screw Point
Boring creosoted poles
Railroad ties
Bulk heads
Heavy Timber
Deep wood boring work
For plumbing, rough-in work, and many other

uses.
Features
Item No.
Description
96300070
96300071
96300072
96300073
96300074
96300075
96300076
96300077
96300078
96300079
96300080
96300081
96300082
96300083
96300084
96300085
96300086
Spade Bit 1/4" X 6"

Spade Bit 5/16" X 6"
Spade Bit 3/8" X 6"
Spade Bit 1/2" X 6"
Spade Bit 5/8" X 6"
Spade Bit 3/4" X 6"
Spade Bit 7/8" X 6"
Spade Bit 1" X 6"
Spade Bit 1-1/8" X 6"
Sets and Accessories

96300089 Spade Bit 17 Piece Set
Box Qty
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
17
Set includes 1 of each of single

blades listed above
96300087
Spade Bit 6 Piece Set
Item No.
Description
96300050
96300051
96300052
96300053
96300054
96300055
96300056
96300057
96300058
96300059
96300060
96300061
96300062
96300063
96300064
Ship Auger 3/8" X 18"

Ship Auger 1" X 18"
Ship Auger 1-1/8" X 18"
Accessories
96300065 Ship Auger Extension 12"
96300066 Ship Auger Extension 18"
Box Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Inside cutter that pushes the wood chips to

the rear of the bit, allowing you to bore faster,
deeper holes in wood, without clogging or
binding
Double-end screw point with medium pitch
screw on one end and a fine pitch screw on
the other provides operator a choice of feed
speeds, depending on the base material
involved
2 recesses provided on one flat of the shank
gives positive grip when used with
extensions, reducing the possibility of losing
the bits in hollow walls or floors.
Packaged individually with extra screws and
wrench
Applications
Boring fast holes through all woods to install
pipes and conduit
Use with Ship Auger extensions for added
reach
Item No.
Multispur
Drill Bit
Description
Application
96902023
96902024
96902083
96902084
96902085
1-3/8"
1-1/2"
1-3/4"
2-1/8"
2-9/16"
For 7/8" Pipes

For 1" Pipes
For 1-1/4" Pipes
For 1-1/2" Pipes
For 2" Pipes
Shank
7/16"
7/16"
7/16"
7/16"
7/16"
Set includes 1 each of 3/8",

1/2",5/8", 3/4", 7/8", 1"
96300088
SPADE BIT EXTENSION 12
www.us.hilti.com
4.12
Bi-Metal Hole Saws And Arbors

Variable Pitch
Individual Hole Saws
Features
Benefits
Arbor sold separately. (See note below for suggested arbor.)
Bi-metal construction
1-1/2" cutting depth
Teeth stay sharp longer

Long life
Smoother cuts
Cuts through 2x4's
Applications
Cut holes in wood, plastic or machinable metal including nail-embedded
wood, plywood, pipe and stainless steel.
Item No.
Description
Arbor
Box
Qty
96205875
96030494
96030496
96030497
96030498
96030499
96030500
96030501
96230502
96030503
96030504
96030505
96205976
96030506
96205977
96030507
96205978
96030508
96030509
96030510
96030511
96030512
96030513
96205979
96030514
96030515
96205980
96030516
96030517
96030518
96030519
96030521
96205981
96030522
96030523
96030524
96205982
96030525
96030526
96205983
96030527
96030528
96030529
96030530
96205984
96030531
9/16" Hole Saw (BI-MTL Var Pitch)

1" Hole Saw (BI-MTL Var Pitch)
1-1/16" Hole Saw (BI-MTL Var Pitch)
*
*
*
*
*
*
*
*
*
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Arbors
1/2" 20 thread size
Includes HSS pilot drill bit
Item No.
Description
96205985
96205989
*ARBOR 1/4 ROUND 9/16" to 1 3/16"

*ARBOR 1/4 HEX 9/16" to 1 3/16"
96205986
*ARBOR 7/16 HEX 9/16 to 1 3/16"
Fits hole saws 9/16" to 1 3/16"
96205987
**ARBOR 3/8 HEX 1 1/4" to 6"
Fits hole saws 1 1/4" to 6"
96205988
**ARBOR 7/16 HEX 1-1/4 - 6

Fits hole saws 1 1/4" to 6"
96030536
Pilot Bit 6pk 1/4 X 4-1/2 for hole saws
Hole Saw Sets
Item No.
Description
96030532
Electricians Kit - Hole Saw (BI-MTL Var Pitch)

8 pc. set complete: 1 each 7/8", 1-1/8", 1-3/8", 1-3/4",
2", 2-1/2" and 2 arbors
96030533
4.13
1
1
Fits hole saws 9/16" to 1 3/16"
* Use with arbors 96205985 or 96205986 (see next column)

* * Use with arbors 96205987 or 96205988 (see next column)
www.us.hilti.com
Box
Qty
Plumbers Kit - Hole Saw (BI-MTL Var Pitch)

8 pc. set complete: 1 each 3/4", 7/8", 1-1/8", 1-1/2",
1-3/4", 2-1/4" and 2 arbors
Annular Cutters
Product Advantages
Features
Applications
Tooth Geometry provides greater mass in the cutting edge

to dissipate heat
One 3/4" arbor system, instead of two, makes it
easy and cost effective
No center punching required
Tougher and more durable than carbide cutters
Cuts faster with less friction for longer life
Can cut up to 2" thick
I-Beams and all structural drilling

Use as faster alternative to Silver
& Deming Drill Bits
Pilots and adapters will work with the
following Magnetic Drill Machines:
Unibor SE100/32, E100/32, E40
Magnabor 18581
Slugger MT3S, MT3
Champion RB65
M2 High Speed Steel

3/4" shanks
Aggressive cutting edges
Industrial quality
For all magnetic drilling
machines
For use with all Hilti and conventional annular cutters.

Pilot pins are necessary for:
Aligning annular cutter to precise drilling point
Providing a steady flow of lubricant to cutting edges
Ejecting the slug from the center of cutter once drilling is complete
1" Length Annular Cutters3/4" shank
2" Length Annular Cutters3/4" shank
Item No.
Description Cutter Size x O/A length
Item No.
Description Cutter Size x O/A length
96902025
96902026
96902027
96902028
96902029
96902030
96902031
96902032
96902033
96902034
96902035
96902036
96902037
96902038
96902039
96902040
96902041
96902042
96902043
96902044
96902045
96902046
96902047
96902048
96902049
96902050
96902051
7/16" X 1" Long Annular Cutter

1" X 1" Long Annular Cutter
1-1/16" X 1" Long Annular Cutter
96902053
96902054
96902055
96902056
96902057
96902058
96902059
96902060
96902061
96902062
96902063
96902064
96902065
96902066
96902067
96902068
96902069
96902070
96902071
96902072
96902073
96902074
96902075
96902076
96902077
96902078
96902079

1-3/4"X 2" Long Annular Cutter
Accessories
Item No.
Description
96902052
96902080
96902081
96902082
Pilot For 1" Cutter

Pilot For 2" Cutter
Adaptor Morse 2
Adaptor Morse 3
www.us.hilti.com
4.14
NEW
Hilti SF 4000-A Cordless Drywall Screwdriver

Cordless Drill/Drivers
NEW !
SF 100-A 9.6 V
SF 121-A 12 V
SF 150-A 15.6 V
SF 180-A 18 V
Page 5.5
Page 5.6
Page 5.7
Page 5.8
Screwdrivers
SF 4000 Drywall Screwdriver
SF 4000-A Cordless Drywall Screwdriver
ST 18 Heavy Duty Torque Adjustable
SU 25 Heavy Duty Depth Adjustable Universal
NEW !
Page 5.9
Page 5.10
Page 5.14
Page 5.15
Screw Program
Collated Drywall Screws
Single Drywall Screws
Self-Drilling Screw Selection Guide
Self-Drilling Screws
Page 5.12
Page 5.13
Page 5.16
Page 5.20+
Accessories
Insert Bits
Power Bits
Magnetic Nut Setter
Page 5.27
Page 5.27
Page 5.27

System
Tool Description
SF 100-A
Application
Page
0-350 rpm for high torque applications

0-1300 rpm for high speed applications
New soft grip, rubber handle
Single sleeve keyless chuck with automatic
spindle lock
20-position adjustable clutch settings
Electronically controlled variable speed reversing
switch
Base materials: wood, steel

All types of screwdriving
applications
Light-duty drilling in wood and
sheet metal
5.5
Overall quality and durability improves and

lengthens life of the tool.
Advanced battery and charging technology
Optimized handling and weight
Small, compact, and cordless
Soft-grip cover
High adjustable torque rating and larger battery
capacity

applications
Light-duty drilling in wood and
sheet metal
5.6
Advanced battery and charging technology

Overall quality and durability
Optimized handling and weight
Small, compact, and cordless
Soft-grip cover
High adjustable torque rating and larger battery
capacity

applications
Cutting recesses with a hole-saw
Drilling rapidly through sheet metal
5.7
Powerful motor and durable steel gear for long

lifetime and reliability
Performance similar to corded tools, while high
battery capacity ensures mobility and flexibility
Rubber-padded grip, superb balance,
ergonomically placed control buttons for optimum
working comfort
Tapered chuck for better corner accessibility
Base materials: wood, steel, masonry,

tile, light concrete
applications
Drilling in metal and wood
Hammer drilling in masonry and
light concrete
5.8
Accessories:
5.27
9.6 V
Cordless Drills/Drivers
SF 121-A
Accessories:
5.27
12 V
SF 150-A
Accessories:
5.27
15.6 V
SF 180-A
NEW!
18 V
SF 100-A
SF 121-A
Drill/Driver
SF 150-A
Drill/Driver
SF 180-A
Hammer Drill/Driver
SF 4000-A
Drywall Screwdriver
TE 6-A
Rotary Hammer Drill
Battery
Standard
charger
Type of battery
2.0 Ah
NiCd
3.0 Ah
NiMH
2.0 Ah
NiCd
3.0 Ah
NiMH
2.0 Ah
NiCd
3.0 Ah
NiMH
2.0 Ah
NiCd
3.0 Ah
NiMH
2.0 Ah
NiCd
3.0 Ah
NiMH
2.4 Ah
NiCd
Voltage
9.6 V
9.6 V
12 V
12 V
15.6 V
15.6 V
18 V
18 V
18 V
18 V
36V
Designation
SBP
10
SFB
105
SFB
121
SFB
126
SFB
150
SFB
155
SFB
180
SFB
185
SFB
180
SFB
185
BP
TCU 4/36
SCF 7/18H
Top charger
SFC 7/18
Application
Hilti Battery Systems
Tool
Drill/Driver
TCU 7/36
Screw driving
Drilling
Hammer drilling (cam action)
+
+
Rotary hammer drilling (electro pneumatic)
5.3
TE 6-A
See Page
2.17

System
Tool Description
Application
Page
SF 4000
No load-speed: 4300 rpm

Controlled Air Guidance diverts exhaust air out
of the bottom of the tool
2.8 lb Lightweight for less user fatigue
8.3 inches in length Compact design for
access to tight spaces
Integrated scaffold hook for easy tool storage on
lifts and scaffolds
Cord options: 15 ft and 50 ft with twist lock
Drywall installation and framing

Touch-up work
Inspections
5.9
SF 4000-A

Optimal performance for all drywall applications in
interior finishing
Lockbutton power switch increases battery
capacity for longer use
Drywall installation and framing

Touch-up work
Inspections
5.10
SMI 55
Collated drywall screw magazine for use with

SF 4000 snd SF 4000-A drywall screwdrivers
Automatic feeding system for

drywall installation
5.11
ST 18
Heavy
Duty

18-position torque clutch and 192 in.-lb. of max
torque for a variety of heavy duty workloads
Depth sensitive clutch for controlled pressure on
sealing washer allows for optimal sealing of
fastener exposed to weather
Electronic variable speed switch for increased
control
Reversing switch for clockwise or counterclockwise rotation
Lockbutton for sustained operation
Sheet metal to sheet metal

Sheet metal to steel or aluminum
structures
Sheet metal to wood structure
Composite panel to steel structure
5.14
SU 25
Heavy
Duty

Snap on/off adjustable depth nose cone for proper
installation of self sealing rubber gasket fasteners
or driving screws in soft material such as wood
switch for easy fastener starts and greater user
control
KWIK CLUTCH provide consistent fastener depth
with quiet operation and longer life
Metal to wood
Wood to wood
Wood to chipboard
5.15
Screwdrivers
18 V Cordless
Accessories:
5.27
Accessories:
5.27
Screw Driving Torque

Torque is a measure of rotational force, typically expressed in foot-pounds
[ft-lb], or inch-pounds [in-lb] (recall 1 ft-lb = 12 in-lb). Its how hard a product
can twist. The only current nationally-recognized test for measuring torque on
Electric Screw Drivers (ESDs) is a European standard. Following are a few common
terms you may encounter, and what they mean (per the European standard).
Rigid Joint, or Hard Joint torque: This test condition involves
driving a screw or bolt into a pre-drilled hole in a hard base material
(usually metal). The screw is driven in until the head bottoms out and the
tool stalls. Because of the rigid base material, the screw is stopped quickly
once it bottoms out (<30 after snug). A calibrated wrench is then used to
measure the torque required to further tighten the screw this is the Rigid
Joint or Hard Joint torque. A Rigid Joint or Hard Joint torque figure will
always be the highest number that can be obtained for an ESD.
Flexible Joint, or Soft Joint torque: This test condition is the
same as the Rigid/Hard Joint, except that the screw/bolt is driven into a
soft base material (such as wood, or a series of washers that can be
compressed). Under these conditions, the screw/bolt will rotate considerably
farther after it becomes snug (>720), meaning the stalling takes longer to
occur. The Flexible/Soft Joint torque more closely represents the capability
of the tool in these more common applications.
5.4
SF 100-A 9.6 V Cordless Drill/Driver

Lightweight, Comfortable Soft Grip Ideal For Production Work
Technical Data
Battery voltage and capacity
2.0Ah 3.0Ah
s
H Cells
NiCd Cell NiM
SBP 10: 2.0 Ah on 9.6 V = 19.2 Wh

SFB 105: 3.0 Ah on 9.6 V = 28.8 Wh
No-load speed
1st speed: 0350 rpm
Tool weight with battery

with 2.0 Ah NiCd: 3.75 lb
with 3.0 Ah NiMH: 3.83 lb
Max torque
Flexible screw fstng in wood: 11.8 ft-lb
Rigid screw fstng in metal: 17 ft-lb
Torque clutch
Precision range between 15.2 ft-lb
with 20 settings
Chuck type /clamping range

Keyless chuck,1/32" to 3/8" diameter
capacity
fstng =fastening

Features & Benefits

3.0 Ah NiMH batteries provide
50% longer run time
Two speed gear setting for a
wide range of applications
0350 rpm for high torque
applications ideal for
larger diameter drill bits
01250 rpm for high speed
applications ideal for driving
screws or using small diameter

drill bits
Soft grip, rubber handle for
increased operator comfort
Single sleeve keyless chuck with
automatic spindle lock provides
easy bit changes and secure
retention of bits
20 position adjustable clutch
settings for proper fastener
installation and reducing fastener

overdrive providing greater user
control
Electronically controlled variable
speed reversing switch for
greater control and ease of
fastener start
Lightweight, compact design for
less user fatigue
SF 100-A Cordless Drill/Driver

Item No.
Description
00334591
Hilti SF 100-A 9.6 V Drill/Driver Kit

with 2x 2.0 Ah NiCd Batteries
Supplied with 1 screwdriver SF 100-A, 2 batteries SBP 10
(2.0 Ah NiCd), 1 charger SFC 7/18, 1 double bit S-B PH2,
operating instructions and safety precautions in a plastic Hilti
case
00334600
www.us.hilti.com
Hilti SF 100-A 9.6 V Drill/Driver Kit

with 2x 3.0 Ah NiMH Batteries
Supplied with 1 screwdriver SF 100-A, 2 batteries SFB 105
(3.0 Ah NiMH), 1 charger SFC 7/18, 1 double bit S-B PH2,
case
Batteries For SF 100-A

Item No.
Description
Screw Program see page:
00334584
SFB105 battery in cardboard box (3.0 Ah NiMH)
5.16
00315079
SBP10 battery in cardboard box (2.0 Ah NiCd)
SFC 7/18 Charger
5.27
Item No.
Description
00334627
SFC 7/18 charger in cardboard box
Operating instructions and safety precautions included
Drill Bits/Holesaw
see section:
4.0
Drill & Specialty Bits
Drill Bits see page 4.5+
Specialty Bits see page 4.11+
5.5
SF 121-A 12 V Cordless Drill/Driver

Ergonomic Soft Grip Design For Easy Installation Of Screws And Comfortable Drilling
2.0Ah 3.0Ah
s
H Cells
NiCd Cell NiM
Technical Data
SFB 121: 2.0 Ah at 12 V = 24 Wh
SFB 126: 3.0 Ah at 12 V = 36 Wh
No-load speed
1st speed: 0400 rpm

with 2.0 NiCd: 4.3 lb
with 3.0 NiMH: 4.4 lb
Max torque
Rigid screw fstng in metal: 18.4 ft-lb
Torque clutch
Features & Benefits

Ultimate battery capacities
provide top performance less
down time
Great energy reserves for
demanding screwdriving and
drilling jobs
High torque for a wide range of
applications
Optimum design permits working

without tiring
Tapered chuck for easy access in
tight corners
Motor brake minimizes stopping
time for even drill/driving depth
and neat appearance of the
finished fastening
Built-in spindle lock for easy

chuck operation
Soft grip on batteries protect
work surfaces from scuffing and
scratching and prevents tool from
sliding on slippery surfaces
Two long-lasting batteries and
rapid charger in every kit permits
continuous work

with 15 settings

Keyless chuck, 1/16" to 1/2" Diameter
capacity
fstng =fastening

SF121-A & SF 150-A Cordless Drill/Drivers

Item No.
Description
00340440
Hilti SF 121-A 12 V Drill/Driver

Supplied with one SF 121-A cordless drill/driver, two SFB 121
batteries (2.0 Ah NiCd), one SFC 7/18 battery charger, operating
instructions and safety precautions in a plastic Hilti case
00340446
Hilti SF 121-A 12 V Drill/Driver Kit

batteries (3.0 Ah NiMH), one SFC 7/18 battery charger,
case
Batteries for SF 121-A

00340888
SFB 121 battery (2.0 Ah NiCd) in cardboard box
00340889
SFB 126 battery (3.0 Ah NiMH) in cardboard box
SFC 7/18 rapid charger
00334627
SFC 7/18 battery charger in cardboard box
5.16
Accessories
Item No.
Description
00370494
SFL 12/15 Flashlight
www.us.hilti.com
Supplied with operating instructions and safety precautions,

battery not included
5.27
Drill Bits/Holesaw
see section:
4.0
Drill & Specialty Bits
Drill Bits see page 4.5+
Specialty Bits see page 4.11+
5.6
Cordless Drill/Driver
SF 150-A 15.6 V Cordless Drill/Driver

Ergonomic Soft Grip Design For Easy Installation Of Screws And Comfortable Drilling
Technical Data
SFB 150: 2.0 Ah at 15.6 V = 31.2 Wh
SFB 155: 3.0 Ah at 15.6 V = 46.8 Wh
No-load speed
1st speed: 0450 rpm
h
2.0Ah 3.0A
Cells
ells NiMH
NiCd C

with 2.0 NiCd: 4.8 lb
with 3.0 NiMH: 4.9 lb
Max torque
Rigid screw fastening in metal: 25 ft-lb
Torque clutch
with 15 settings

Keyless chuck, 1/16" to 1/2"
fstng =fastening

Features & Benefits

Ultimate battery capacities
provide top performance less
down time
Great energy reserves for
demanding screwdriving and
drilling jobs
High torque for a wide range of
applications
Optimum design permits working

without tiring
Tapered chuck for easy access in
tight corners
Motor brake minimizes stopping
time for even drill/driving depth
and neat appearance of the
finished fastening
Built-in spindle lock for easy
chuck operation
Soft grip on batteries protect

work surfaces from scuffing and
scratching and prevents tool from
sliding on slippery surfaces
Two long-lasting batteries and
rapid charger in every kit permits
continuous work
SF 150-A Cordless Drill/Drivers

Item No.
Description
00340455
Hilti SF 150-A 15.6V Drill/Driver Kit

batteries, one SFC 7/18 battery charger, operating
instructions and safety precautions in a plastic kit box
00340462
Supplied with one SF 150-A cordless drill/driver, two SFB SFB

155 batteries, one SFC 7/18 battery charger, operating
instructions and safety precautions in a plastic kit box
www.us.hilti.com
5.16
Batteries for SF 150-A

00340890
SFB 150 battery (2.0 Ah NiCd) in cardboard box
00340891
SFB 155 battery (3.0 Ah NiMH) in cardboard box
SFC 7/18 Charger
00334627
SFC 7/18 charger in cardboard box
Drill Bits/Holesaw
see page:
5.27
Hilti SF 150-A 15.6V Drill/Driver Kit

Accessories
00370494
SFL 12/15 Flashlight
Supplied with operating instructions and safety precautions,

battery not included
4.2
5.7
SF 180-A Cordless Cam-Action Hammer Drill/Driver

Ultimate Versatility and Mobility
NEW!
Technical Data
Power
SFB 180: 2.0 Ah on 18V = 36 Wh
SFB 185: 3.0 Ah on 18V = 54 Wh
Chuck type: clamping range

Quick Release: 1/16" to 1/2"
Max torque
Flexible screw fastening in wood:
22.9 ft-lb
Rigid screw fastening in metal:
30 ft-lb
Clutch torque setting

18 to 106 in-lb in 13 increments
Smooth electronic speed control

Professional screwdriving, drilling
and hammer drilling in one tool,
with a speed up to 1,600 rpm
Drills in wood, metal, masonry,
tiles; drives medium-duty screws
and anchors
Powerful motor and durable steel

gear for long life and reliability
Smooth speed control ensures
perfectly matched spindle speed
and torque for maximum drilling
and screwdriving
Performance similar to corded
tools, with high battery capacity
for increased mobility and
flexibility
Rubber-padded grip, superb

balance, ergonomically placed
control buttons for optimum
comfort
Tapered chuck for better corner
accessibility
1st gear: 0460 rpm

2nd gear: 01600 rpm
Hammering speed
028800 blows/min
Weight with battery and side

handle
5.73 lb
Drilling capacity
Softwood/particle boards:
up to 1-1/4" diameter
(up to 4" with holesaw)
Sheet metal (max 3/8" thick):
up to 1/2" diameter
Masonry, light concrete, tiles:
up to 3/8" diameter
Hilti SF 180-A cordless hammer drill/driver

Item No.
Description
00374998
SF 180A 18 V Hammer Drill/Driver

with 2x2.0 Ah NiCd Batteries

Supplied with 1 SF180-A, 2 batteries SFB 180 (2.0 Ah, NiCd),

1 standard battery charger SFC 7/18H, side handle, operating
instructions and safety precautions in a kit box.
00375005
SF 180-A 18 V Hammer Drill/Driver

with 2x3.0 Ah NiMH Batteries
Supplied with 1 SF 180-A, 2 batteries SFB 185 (3.0 Ah, NiMH),
1 top battery charger SFC 7/18, side handle, operating
instructions and safety precautions in a kit box.
Batteries for SF 180-A / SF 4000-A / SFL18

00370100
SFB 180 battery in a cardboard box (2.0 Ah NiCd)
00370102
SFB 185 battery in a cardboard box (3.0 Ah NiMH)
Chargers
00334627
www.us.hilti.com
5.16
SFC 7/18 top charger (rapid) in a cardboard box
5.27
Supplied with operating instructions and safety precautions
00370097
SFC 7/18H standard charger (hour) in a cardboard box

Accessories
00370561
SFB 180/185 battery belt adapter in a cardboard box

00370495
SFL 18V Flashlight in a cardboard box
Drill Bits/Holesaw
see page:
4.2
5.8
Screwdrivers

The Light Tool For Heavy Rockin
Technical Data SF 4000

Voltage
Save $$$
with special
120 V
Bulk Pricing!
Nominal power
500 W
Nominal current
4.5 A
No-load speed
Ask your Hilti Sales Person or
Customer Service Representative for details
04000 rpm
Max. torque
4.8 ft-lb
Weight (without supply cord)

2.8 lb
Supply cord length

15 ft/50 ft
Features/Benefits
2.8 lb lightweight for less
user fatigue
Compact design (8.3 inch in
length) for tight access
Controlled Air Guidance
diverts exhaust air out of the
bottom of the tool and provides
protection to users hands
SF 4000 available with 15 ft

standard cord or 50 ft cord with
twist lock plug for greater
freedom of movement
Integrated scaffold hook easy
tool storage on lifts and on
scaffolds (adjustable and
removeable)
Push-through forward reverse

button provides easy access and
greater durability
Lock on button for continuous
operation
Removable belt clip easy
storage and easy tool-free
removal

Item number
00334424
Description
Hilti SF 4000
Equipped with 2-1/4" magnetic bit holder, Phillips #2 bit,
aluminium depth gauge, operating instructions, 15 foot cord
00337803
Hilti SF 4000 W
Equipped with 2-1/4" magnetic bit holder, Phillips #2 bit,
aluminium depth gauge, operating instructions, 50 foot cord
with twist lock plug
Accessories
Item number
Description
00334431
00240488
00240489
00265869
00265879
Plastic Hilti case

Depth gauge
Threaded bush assembly
Scaffolding hook (for SF 4000)
Belt hook (for SF 4000)
Insert tools
Item number
Description
00338991
Hilti magnetic bit holder (2 1/4")
Packaging Contents
www.us.hilti.com
5.13
5.9
Cordless Screwdriver
SF 4000-A Cordless Drywall Screwdriver
NEW!
Up to 1,400 screw fastenings per battery charge.*

Powerful corded performance in a cordless tool.
Technical data
Battery capacity*
SFB 180: 6001,000 screws
SFB 185: 9001,400 screws
No-load speed
04,000 rpm
Features & Benefits

Complete mobility and flexibility
from being independent of an
electric supply
Power like a corded tool
Unequalled battery capacity
Performance optimized for all
drywall applications
SMI55 screw magazine for

extremely high fastening rate
Lockbutton for sustained
operation
Ideal cooling air guidance keeps
dust away from user
Much quieter motor than on
corded tools
Practical belt and scaffolding

hooks
Rubber-padded grip
Light as a corded tool when
using the belt adaptor
Robust design, service-friendly
components, sense of security
from full service for 12 months
Max. torque
4.8 ft-lb
Tool weight
with battery: 5.11 lb
with belt adapter: 2.9 lb

*Results based on fastening drywall with 1" drywall screws into light guage framing with trigger lock engaged. Results may vary.
SF4000-A battery drywall screwdriver

Item No.
Description
00340746
Hilti SF4000-A 18V Drywall Screwdriver

Supplied with one SF 4000-A cordless drywall screwdriver,
two SFB180 batteries (2.0 Ah NiCd), one SFC7/18H standard
battery charger (hour), operating instructions and safety
precautions in a plastic toolbox
00373989
Hilti SF4000-A 18V Screwdriver Kit

with 2x 3.0 Ah NiMh Batteries
Supplied with one SF 4000-A cordless drywall screwdriver,
two SFB185 batteries (3.0 Ah NiMH), one SFC7/18 top battery
charger (rapid), operating instructions and safety precautions
in a plastic toolbox
00340790
Hilti SF4000-A 18V Drywall Screwdriver

Supplied with one SF 4000-A cordless drywall screwdriver in
a cardboard box
Batteries
Item No.
Description
00370100
SFB180 battery 2.0 AH (NiCd) in cardboard box
00370102
SFB185 battery 3.0 AH (NiMH) in cardboard box
Battery chargers
Item No.
Description
00370097
In cardboard box with operating instructions and safety precautions
00334627
SFC7/18 battery charger (rapid)
In cardboard box with operating instructions and safety precautions
SFC7/18H battery charger (hour)
Accessories
Item No.
Description
00340748
00266054
00257255
00318440
00318439
00370561
Insert tools
SF 4000-A Plastic toolbox

Depth gauge (75 mm)
Depth gauge (40 mm)
Scaffolding hook (for SF 400-A)
Belt hook (for SF 4000-A)
18V battery belt adapter
Item number
Description
00338991
Hilti magnetic bit holder (2 1/4")
Packaging Contents
www.us.hilti.com
5.13
5.10
Cordless Screwdrivers
SMI 55 Collated Drywall Screw Magazine

Teamwork For Peak Performance with SF 4000 Screwdriver and
SF 4000-A Cordless Screwdriver
Features & Benefits
No tools required for easy
attachment and adjustment for
use with Hilti SF 4000 screwdriver
Completely modular, high-tech
durable plastic unit designed for
easy disassembly and cleanup
with water
Lightweight design (only 0.8 lb)
and low contact pressure required
for driving screws mean less user
fatigue and ease of operation
Innovative screw transport
system design for easy screw
advancement and less jamming
Easy-to-adjust depth setting
allows proper fastener installation
Technical Data SF 4000 SMI 55

Voltage
120 V
Nominal power
500 W
Nominal current
4.5 A
No-load speed
04000 rpm
Max. torque
4.8 ft-lb
Weight (without supply cord)

3.6 lb
Supply cord length

15 ft/50 ft
Length:
15.5 in
Hilti Drywall Screw Magazine SMI 55 - Savings Calculation - Example*

Job Total: 100,000 screws
Screws per day
Man-days to complete job
2500
40.0
Increased productivity with SMI 55

Screws installed per day without Hilti SMI 55
Screws installed per day with Hilti SMI 55
2500
3000
Savings with increased productivity using SMI 55

Man-Days to complete job using SMI 55
33.3
Man-Days Savings
6.7
* Example takes into account screw installation time only
20% greater productivity
17% savings
Item No.
Description
00310953
SMI 55 Collated Drywall Screw Magazine

Supplied with S-MBL 166 PH2 Phillips bit, strip guide, built-in
SD-45 adapter and operating instructions
SMI 55 Drywall Screw Magazine System

Item No.
Description
00095853
SMI 55 & SF 4000 in cardboard box

Supplied with S-MBL 166 PH2 Phillips bit, strip guide , builtin adapter, magnetic bit holder, Phillips #2 bit, depth gauge,
operating instructions, safety precautions, 15-foot supply cord
00095859
SMI 55 & SF 4000 W in cardboard box

Supplied with S-MBL 166 PH2 Phillips bit, strip guide , builtin adapter, magnetic bit holder, Phillips #2 bit, depth gauge,
operating instructions, safety precautions, 50-foot supply cord
with twist lock plug
00373990
www.us.hilti.com
SMI 55 & SF 4000-A W in cardboard box

Supplied with one SF 4000-A cordless screwdriver, two
SFB180 batteries (2.0 Ah, NiCd), one SFC 7/18H battery
charger (hour); and SMI 55 magazine including S-MBL 166
PH 2 Phillips bit
5.12
5.11
Drywall Screws
SMI 55 Collated Drywall Screws

Save $$$
with special
Screws In Magazine Strips of 50
Bulk Pricing!
S-DS Sharp Drywall Screws With Fine Thread

For Drywall sheets on metal profile up to 25 gauge
Item No.
Description
00254805
S-DS 6 x 1 1/8 PBH sharp collated
00254806
00254807
00331927
S-DS 6 x 2 PBH sharp collated
S-DC Sharp Course Thread Drywall Screws
Length (in.)
Pkg Qty
6 x 1-1/8
6 x 1-1/4
6 x 1-5/8
6x2
1000
1000
1000
1000
For Drywall sheets on wood

Item No.
Description
00314640
S-DC 6 x 1 1/8 PBH S. CRS collated
00254809
00254810
00331919
S-DC 6 x 2 PBH S. CRS collated Kwik-Cote
00331921
S-DC 6 x 2 PBH S. CRS collated black
S-DD Self-drilling Zinc-plated1 Drywall Screws
Length (in.)
Pkg Qty
6 x 1-1/8
6 x 1-1/4
6 x 1-5/8
6x2
6x2
1000
1000
1000
1000
1000
For Drywall sheets on metal profile up to 20 gauge

Item No.
Description
Length (in.)
Pkg Qty
00316645
00314646
00314647
00331931
S-DD 6 x 1 1/8 PBH SD zinc collated

S-DD 6 x 2 PBH SD zinc collated
6 x 1-1/8
6 x 1-1/4
6 x 1-5/8
6x2
1000
1000
1000
1000
1 Zinc-plated in accordance with ASTM B633.
Special Bit For SMI 55

Item No.
Description
00310954
S-MBL 166 PH2

All screws from the drywall screw program are
also available in bulk packages.
Ask your Customer Service Representative for details.
Hilti Screw Fasteners Test Methods and Approval Listings

All Hilti, Inc. screw fasteners are tested in accordance
with and meet all criteria outlined in ICBO ES AC 118
Acceptence Criteria for Tapping Screw Fasteners.
ICBO ES AC 118 references and specifies the following
documents:
ANSI/ASME B 18.6.4
SAEJ78
ASTM A370
ASTM B117
ASTM C954
ASTM C1002
AISI Test Methods for Mechanically Fastened
Cold-Formed Steel Connections (CF-92-1),
February 1992
Hilti Kwik-Pro Self-drilling screws are covered under
ICBO ES Evaluation Report 5202 and City of Los
Angeles Research Report 25294.
Hilti Kwik-Flex self-drilling screws are covered under

ICBO ES Evaluation Report 4780 and City of Los
Angeles Research Report 25095.
All Hilti Drywall sharp point screws meet or exceed
ASTM C1002 requirements for corrosion resistance and
performance.
All Hilti Drywall self-drilling screws meet or exceed
ASTM C-954 requirements for corrosion resistance and
performance.
All Hilti zinc plated screw conform to ASTM B633, as
tested in accordance with ASTM B117.
All Hilti screw fasteners conform with The Industrial
Fasteners Institute (IFI) specifications for tapping screws
published in 1988, Sixth Edition, Section H, Page H-1
through H-78.
www.us.hilti.com
5.12
Drywall Screws
KWIK-PROTM Sharp Point Drywall Screws

Hilti Drywall Screws meet ASTM C-1002 Standards.
Sharp Point Screws
Description
Item No.
6 x 1 PBH S
6 x 1 1/8 PBH S
6 x 1 1/4 PBH S
6 x 1 5/8 PBH S
6 x 2 PBH S
6 x 2 1/4 PBH S
7 x 2 1/2 PBH S
8 x 3 PBH S
10 x 3-3/4 PBH S
10 x 4-1/2 PBH S
10 x 5 PBH S
10 x 6 PBH S
6 x 1 PBH S H/L
6 x 1-1/8 PBH S H/L
6 x 1-1/4 PBH S H/L
6 x 1-5/8 PBH S H/L
6 x 2 PBH S H/L
6 x 2-1/4 PBH S H/L
7 x 2-1/2 PBH S H/L
8 x 3 PBH S H/L
6 x 1 PBH S CRS THRD
6 x 1-1/8 PBH S CRS THRD
10 x 1-1/2 PBH S Laminating
00084297
00084329
00084291
00084323
00084310
00084311
00084319
00084328
00084326
00086894
00084306
00084334
00086197
00086198
00086199
00086200
00086201
00086202
00086302
00086204
00084325
00084316
00084294
00084307
00084320
00084295
00084322
00084317
00086205
Carton qty
10,000
10,000
8,000
5,000
3,500
3,000
2,500
2,000
1,000
750
1,300
500
10,000
10,000
8,000
5,000
3,500
3,000
2,500
2,000
10,000
10,000
8,000
5,000
3,500
3,000
2,500
2,000
5,000
7 x 7/16 PPH S Framer

6 x 7/16 S CRS Framer
8 x 1/2 PTH S Lathing Zinc
8 x 3/4 PTH S Lathing Zinc
8 x 1 PTH S Lathing Zinc
8 x 1-1/4 PTH S Lathing Zinc
6 x 1-5/8 PFH S Trim Head
6 x 2-1/4 PFH S Trim Head
6 x 1-5/8 SFH S Trim Head*
6 x 2-1/4 SFH S Trim Head*
*Square Drive (#1)
00086206
00086207
00010262
00010263
00010264
00010265
00084313
00084332
00086210
00084331
10,000
10,000
10,000
10,000
8,000
6,000
5,000
3,000
5,000
3,000
Applications
Fastening drywall to metal studs

from 25 ga through 20 ga
Fastening drywall to metal studs

from 25 ga through 20 ga
Fastening drywall to woods studs
Type G laminating screw for

temporary fastening of drywall
to drywall
Fastening stud to track from
20 ga 25 ga
Fastening wire lath to 20 ga 25 ga
studs
Fastening wood trim and base to

20 ga 25 ga studs
KWIK-PROTM Self-Drill Drywall Screws

Hilti Self-Drilling Drywall Screws meet ASTM C-954 Standards.
Self Drilling Screws
$$
Saitvhesp$ecial
ricin
P
k
l
u
B
w
g!

www.us.hilti.com
5.13
Description
Item No.
6 x 1 PBH SD
6 x 1 PBH SD Zinc
6 x 1-1/8 PBH SD
6 x 1-1/8 PBH SD Zinc
6 x 1-1/4 PBH SD
6 x 1-5/8 PBH SD
6 x 1-7/8 PBH SD
8 x 2-3/8 PBH SD
8 x 2-5/8 PBH SD
8 x 3 PBH SD
8 x 3 PBH SD Zinc
7 x 7/16 PPH SD Framer
7 x 7/16 PPH SD Framer Zinc
8 x 1/2 PPH SD Framer Zinc
8 x 1/2 PTH SD Lathing Zinc
8 x 3/4 PTH SD Lathing Zinc
8 x 1 PTH SD Lathing Zinc
8 x 1-1/4 PTH SD Lathing Zinc
6 x 1-5/8 SFH SD*
6 x 1-5/8 SFH SD Zinc*
6 x 2-1/4 SFH SD*
6 x 2-1/4 SFH SD Zinc*
*Square Drive (#1)
00086211
00086212
00086213
00086214
00084290
00086215
00086216
00086217
00086218
00086219
00086220
00086221
00084293
00086222
00086223
00086224
00086225
00086226
00086897
00086228
00087145
00086231
00086232
00086233
00086234
00086235
00086236
Carton qty
10,000
10,000
10,000
10,000
8,000
8,000
5,000
5,000
4,000
4,000
2,500
2,500
1,600
1,600
1,400
1,400
10,000
10,000
10,000
10,000
10,000
8,000
6,000
5,000
5,000
3,000
3,000
Applications
Fastening drywall, plywood,

insulation, etc. to metal studs from
14 ga 20 ga metal studs
Fastening stud to track from

14 ga 20 ga
Fastening wire lath to 14 ga 20 ga

studs
Fastening wood trim and base to
14 ga 20 ga studs
Electric Drills/Drivers
Hilti ST 18 Heavy Duty Torque Adjustable Screwdriver

Ideal Tool For Fastening Steel To Steel Or Steel To Wood
Applications
Sheet metal to sheet metal
Sheet metal to steel or
aluminum structures
Sheet metal to wood structures
Composite panels to steel
structures
Technical Data
Voltage:
110115 V
Nominal Power:
600 W
Nominal Current:
6.0 A
No-Load Speed:
01900 rpm
Weight:
4.0 lb
Max. Torque:
192 in-lb
Adj. Torque
Features & Benefits

Heavy-duty 6A motor provides efficient power for high
torque fastener applications
01900 rpm provides proper speed and torque for a
wide variety of self-drilling fasteners in a broad range
of materials
18 position adjustable torque clutch provides the
proper installation torque to reduce stripping and
fastener overdrive.
Snap on/off adjustable depth nose cone for proper

installation of self-sealing rubber gasket fasteners or
driving screws in soft material such as wood
switch for easy fastener starts and greater user
control.
9 in-lb to 177 in-lb
Chuck:
1/4" hexagon socket with ball-notch
retention

Hilti Depth Gauge Selection

Depth Gauge
R e p a i r
P r o g r a m
Depth Gauge Accessories
Item No.
Type
Dimensions
00240549
S-GU 131
00240550
S-GT 172
00240551
S-GT 23
Length
Bore3
O.D.
Length
Bore3
O.D.
Length
Bore3
O.D.
60 mm
13 mm
25 mm
55 mm
17.5 mm
27 mm
55 mm
23.5 mm
33 mm
Magnetic Bit Holder
Nut Setter
00257257 Short
N/A
N/A
1/4"
5/16"
3/8"
1/4"
5/16"
3/8"
N/A
Bit Tip
PHL#2 or PHL#3
00374640
00374641
00374642
00374640
00374641
00374642
N/A
N/A
1 S-GU 13 utilized for short bit holder with insert bit tips only, packaged standard with SU 25
2 S-GT 17 Depth Gauge packaged standard with ST 18
3 Bore measurement designates maximum washer diameter of screw, for proper depth gauge
www.us.hilti.com
Item No.
Description
00255932
ST 18 Tapper in cardboard box

Complete with S-GT 17 depth gauge depth gauge, 13+ft.
supply cord, operating instructions and safety precautions.
00257395
Plastic Hilti Case
Self-drilling screws, page:
5.20+
5.27
5.14
Electric Drills/Drivers
Hilti SU 25 Heavy Duty

Depth Adjustable Universal Screwdriver
Technical Data SU 25
Voltage
110115 V
Nominal Power
600 W
Nominal Current
6.0 A
No-Load Speed
02200 rpm
Max. Torque
168 in.-lb
Weight
3.3 lb
Chuck
1/4" hexagon socket with ball-notch
retention

R e p a i r
Features
Heavy duty 6 A motor provides
efficient power for high torque
fastener applications
02200 rpm ideal speed for
installing self drilling screws
Snap on/off adjustable depth
nose cone for proper installation
of self sealing rubber gasket
fasteners or driving screws in

soft material such as wood
Electronically controlled variable
speed reversing switch for easy
fastener starts and greater user
control
KWIK CLUTCH provides
consistent fastener depth with
quiet operation and longer life
Applications
Metal to wood
Wood to wood
Wood to chipboard
P r o g r a m
Hilti Depth Gauge Selection

Depth Gauge
Depth Gauge Accessories
Item No.
Type
Dimensions
00240549
S-GU 131
00240550
S-GT 172
00240551
S-GT 23
Length
Bore3
O.D.
Length
Bore3
O.D.
Length
Bore3
O.D.
60 mm
13 mm
25 mm
55 mm
17.5 mm
27 mm
55 mm
23.5 mm
33 mm
Magnetic Bit Holder
Nut Setter
00257257 Short
N/A
N/A
1/4"
5/16"
3/8"
1/4"
5/16"
3/8"
N/A
Bit Tip
PHL#2 or PHL#3
00374640
00374641
00374642
00374640
00374641
00374642
N/A
N/A
1 S-GU 13 utilized for short bit holder with insert bit tips only, packaged standard with SU 25
2 S-GT 17 Depth Gauge packaged standard with ST 18
3 Bore measurement designates maximum washer diameter of screw, for proper depth gauge
www.us.hilti.com
5.24
Item No.
Description
00255940
SU 25 Universal Screwdriver
Complete with S-GU 13 depth gauge, 13 ft supply cord,
operating instructions and safety precautions.
00257395
Plastic Hilti Case
5.27
5.15
Screw Selection
What you need to know about Hilti self-drilling screws
Nomenclature Guide
S-MD 10 - 16 x 3/4 HWH #3 XX YY

Screw
Diameter
of Screw (d)
Length
of screw (L)
Threads per inch (TPI)
Sealing or other
description
Drill point
Head style
Coating
General Application Description

MD = Metal Drill-fastening accessories or metal to metal
WD = Wood Drill-fastening wood (< 1/2") to metal
WW = Wood Wing-fastening wood (>1/2") to metal
Diameter of the screw (d)
TPI-Threads Per Inch
The diameter is important, because the larger

the screw the higher the shear valves that can
be realized.
Thread Length
Holding
Always choose a fastener with sufficient threads

to fully engage in the base metal. For example: If
you are fastening into 1/4" steel, the fastener
should have at least 1/4" of threads. It is helpful,
but not critical, that the threads also engage in
the material being
fastened. The head of the fastener provides the
holding power for the material being
fastened, while the threads provide the holding
power in the base material.
Material Being Fastened

Base Material
Holding
Thread Pitch
The thickness of material being fastened and
diameter of the screw determine the type of
thread pitch to be used. In general, the thinner
the base material, the fewer the number of
threads. The thicker the material, the greater the
number of threads. This principle is due to two
primary methods of thread engagement/holding
power: Clamping and Threading. In light
gauge metal, the materials are actually being
clamped together by the upper and lower
threads.
Therefore, the thinner the material, the coarser

the thread pitch must be to assure proper
clamping. The thicker the material, the finer the
threads must be. In very thick metal
(3/8" 1/2" thick), a fine thread is advisable.
This will allow the thread to tap into the base
material with less installation torque than a
coarse thread.
Thread Engagement
Clamping
Holding
Holding
www.us.hilti.com
5.16
Screw Selection
What you need to know about Hilti self-drilling screws
Hilti Screw Fastening Systems Guide to Corrosion Resistance
CARBON STEEL COATED
Protective Coating
Composition/Appearance
Salt Spray
Test Results
Salt Spray
Properties
Anti-Corrosion
Comments
Phosphate and Oil
Black oil finish
24 to 48 hours
Poor
Basic coating for drywall screws

Good adhesion to drywall mud
Non-corrosive applications
Zinc electroplate
with Chromate
Silver to graybright
24 to 48 hours
Fair
Standard for industrial applications

Superior to cadmium in most industrial
atmospheres
Non-corrosive applications
Hot-dip Galvanized/Chromate
Organic (Kwik-cote or Equal)
Gray
144 to 800 hours
Very Good
High performance coating

Superior to most plated finishes
Kwik Seal Screws- Exposed
Zinc is the standard coating
Length of Screw (L)
Head Style
Depending on the screwhead, there are two

different ways of measuring the overall length of
a screw.
HWH, PPH screws overall length is measured
from the bottom of the collar under the head to
the point of the screw.
HWH Hex Washer Head

Washer face provides a bearing surface for the
driving sockets.
PWH Phillips Wafer Head

Large head provides the bearing surface
necessary to seat flush in soft materials.
MF
L
PPH Phillips Pan Head
PWH, PFH screws overall length is measured
from the top of the head to the point of the
screw.
Conventional head for general applications and

provides low profile fastening.
PFH Phillips Flat Head

Used primarily in wood to countersink and seat
flush without splintering the wood.
MF
L
Maximum thickness fastened(MF)

The maximum thickness fastened for all screws
is the length of the threads reduced by the first
three threads (embedment in the base material).
See drawings above.
The maximum thickness fastened (MF) is the
total thickness of all materials being fastened.
www.us.hilti.com
5.17
Self-Drilling Screw Program

Thread selection
Drill point / drilling capacity
Conversion Tables
Metal Gauge
Drill point selection
000000
00000
0000
000
00
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Aluminum
Sheet
Metal
(Thickness in decimal
parts of an inch)
0.5800
0.5165
0.4600
0.4096
0.3648
0.3249
0.2893
0.2576
0.2294
0.2043
0.1819
0.1620
0.1443
0.1285
0.1144
0.1019
0.0907
0.0808
0.0720
0.0641
0.0571
0.0508
0.0493
0.0403
0.0359
0.0320
0.0285
0.0253
0.0226
0.0201
0.0179
0.0159
0.0142
0.0126
0.0113
0.0100
0.0089
0.0080
0.0071
0.0063
0.0056
0.0050
0.0045
0.0040
0.4062
0.375
0.3437
0.3125
0.2812
0.2656
0.2391
0.2242
0.2092
0.1943
0.1793
0.1644
0.1495
0.1345
0.1196
0.1046
0.0897
0.0747
0.0673
0.0598
0.0538
0.0478
0.0418
0.0359
0.0329
0.0299
0.0269
0.0239
0.0209
0.0179
0.0164
0.0149
0.0135
0.0120
0.0105
0.0097
0.0090
0.0082
0.0075
0.0067
0.0064
0.0060
Fraction
Decimal
Equivalent
1/64
1/32
3/64
1/16
5/64
3/32
7/64
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
0.015
0.031
0.046
0.062
0.078
0.093
0.109
0.125
0.140
0.156
0.171
0.187
0.203
0.218
0.234
0.250
Top Material to be Drilled

Bottom Material to be Drilled
Total Thickness to
be Drilled
Top Material to be Drilled

Void or Insulation
Total Thickness to
be Drilled
Hole Diameter
Larger than Screw Threads
Top Material to be pre- Drilled
Void or Insulation
Total Thickness to
be Drilled
Sealing
The Kwik Seal sealing screws offer weather resistant fastenings where
moisture or condensation is a factor. The integrated washer/head design seals
the hole to help prevent moisture from dripping into the fastener threads,
reducing corrosive build-up. As added protection against corrosion, all Kwik
Seal sealing screws come standard with Kwik Cote coating. The torque control
and adjustment of the Kwik-Tapper electric screwdrivers help ensure that the
optimal seal is applied.
Screw Diameter Gauge

Number of
Gauge
Decimal
Equivalent
#6
#8
#10
#12
#14
0.138
0.164
0.190
0.216
0.242
Drilling Capacity MD-Applications (Steel to Steel)

#2 Point
.500
Thickness of Material to be Drilled (inches)
Number
of
Gauge
#5
#4 Point Point
#3 Point
.400
.312 .312
.300
.250
.210
.200
.250
.187 .175
.175 .175
.110
.100 .100
.110 .110 .110
0.035
0
#8
#10 #12 #10 #12
1/4 *#12 1/4** #12
Note:
The above chart covers the Hilti standard self-drilling screw

program. For information on specialty fasteners (Kwik Seal, wing
reamers. etc.) contact your Hilti representative.
Shaded area represents optimal drilling range.
* #12 #4 point winged reamer fasteners have a maximum
drill capacity of 0.232".
** 1/4" #4 point winged reamer fasteners have a maximum
drill capacity of 0.250".
www.us.hilti.com
5.18
Product Performance
Ultimate Strengths - Pullout
Considers Base Material Thickness
Average Ultimate Pullout Loads (lb) for Standard Self-Drilling Screws
Screw Thread
#6-20
#8-18
#10-16
#8-18
#10-16
#12-14
1/4-14
Head Style
HWH/PPH
HWH/PPH
HWH
SHWH
HWH/PPH
HWH
HWH
Point
2
2
2
3
3
3
3
Steel Thickness
20 GA 18 GA 16 GA 14 GA 13 GA 12 GA
285
470 585
875 1065
300
525 660
950 1215 1540
320
535 700
980 1290 1600
1330
1450
1545
1745
10 GA 5/32" 3/16" 7/32"
1/4"
1/2"
1/4"
1/2"
1575*
1970 2100*
2180 2685 2800*
2285 3220 3850* 3850*
Average Ultimate Pullout Loads (lb) for Specialty Self-Drilling Screws

Screw Thread
#10-24
#8-18
#12-24 W/WINGS
1/4-20 W/WINGS
#12-24
#12-24
11-16 W/WINGS
12-14
Steel Thickness
Point 20 GA 18 GA 16 GA 14 GA 13 GA 12 GA
3
300
495 605
920
3
290
475 585
845 1070 1550
4
530
780 1070 1125
4
605
985 1200 1450
4
675
880
1350
DRILL-IT
740
885
1400
4
905
5
Head Style
PWH
PFH
PFH
PFH
HWH
HWH
PWH
HWH
10 GA 5/32" 3/16" 7/32"

1575
1645
2070
1940
2010
1900
2120
2500
2605
2555
2350
3520 4120*
3195 3250*
3125 3250* 3250* 3250*
1960
2050
2850 4000
* Indicates screw failed in tension before pull-out occurred.

Test cannot be run for each possible combination of fastener and materials. Published tests should be used as a guide only. Sheet metal used for standard and specialty self-drilling screw test data is
cold rolled 1010 strip steel, 1/4 to 1/2 hard; RB 60-85, yield strength 33 to 50 ksi. Consideration must also be given to the pull-through strength of the material being fastened.
Ultimate Strengths - Screw Only
Pullover Test
Does Not Consider Base Material Thickness
Average Ultimate
Pullover Loads for Standard Self-Drilling Screws*
Size
4-24
4-40*
6-20
6-32*
8-18
8-32*
10-16
10-24
10-32*
12-14
12-24
Torsional
Strength
(in.-lb)
14
14
25
26
42
50
61
65
75
92
100
Tension
Strength
(lb)
750
800
1185
1200
1575
1900
2100
2300
2700
2800
3250
Shear
Strength
(lb)
490
520
740
790
1050
1265
1400
1570
1800
1875
2175
* Indicates screw failed in tension before pull-out occurred.
Fastener
#10-16x1 1/2" HWH**
#12-14x2"HWH
#12-24x1 1/2"HWH
#1/4-14x2"HWH
18 GA 20 GA 22 GA 24 GA 26 GA
1655 1100 830 750 505
1525 1050 795 710 505
1440 1100 730 700 470
1940 1224 950 855 600
*All gauges of steel tested were 33,000 psi minimum yield strength.
**The washer on HEX Washer Head screws is an integral part of the head and cannot be removed.
Average Ultimate
Pullover Loads for Special Self-Drilling Screws
Fastener
#12-14x1 1/4FLO-SEAL
1/4-14x 1 1/2 FLO-SEAL
12-24 DRILL-IT 5/8
BONDED WASHER
24 GA siding*
1015
985
1045
26 GA siding**
850
845
-
* Actual yield strength 61,00 psi

** Actual yield strength 106,000 psi
Torsional
Tension
Shear
www.us.hilti.com
5.19

= Unexposed
= Exposed
Unsupported Metal SheetsSide Lap: Steel to Steel
Unexposed to weather
U
Recommended Screws : Diameter and Point selection based on design/base material
Item No.
00312011
00312010
Description
S-MD 10-16X7/8 HWH Pilot Point

S-MD 12-14x1 HWH Stitch
Drilling Capacity (DC)

min, in. / max, in.
0.028
0.028
0.100
0.100
Max. Thickness
Fastened (MF) in.
3/16
3/8
0.188
0.375
Socket
Recess
Box
Qty
5/16"
5/16"
6000
3000
Major applications
Overlapping sheets
Recommended Tools & Accessories

Item No.
Description
00255932
ST 18 Heavy Duty Tapper in cardboard box

Complete with S-GT 17 depth gauge, 13+ft. supply cord,
00374641
Magnetic Nut Setter 5/16" Short
Exposed to weather

Item No.
00311619
Description
S-MD 1/4-14x7/8 HWH Stitch Kwik Seal

min, in. / max, in.
0.024
0.045
Max. Thickness
Fastened (MF) in.
5/16
0.313
Socket
Recess
5/16"
Box
Qty
2500

Item No.
Description
00255932

00374641

Major applications
Exterior overlapping sheets
and corner sheets
For specific requirements, such as Buy American Act, or special diameter, points, or lengths,
please contact your Hilti Salesperson or Hilti Customer Service at 1-800-879-8000.
www.us.hilti.com
5.20
Light Gauge Applications: Steel to Steel
= Unexposed
$$
Saitvhesp$ecial
ing
c
i
r
P
ulk
w

Major applications
Fastening of HVAC ducts
Sheet metal assembly
Accessories (electrical, clips,
etc) to steel
Lower profile head for above
mentioned applications (PPH)

min, in. / max, in.
Max. Thickness
Fastened (MF) in.
Item No.
Description
00311438
00311439
00311440
S-MD 8-18 x 1/2 HWH #2

S-MD 8-18 X 3/4 HWH #2
S-MD 8-18 X 1 HWH #2
0.035
0.035
0.035
0.100
0.100
0.100
1/8
3/8
1/2
0.125
0.375
0.500
00311441
00311442
00311443
00311444
00311445
00311446
00311447
S-MD 8-18 x 1/2 PPH #2

S-MD 8-18 X 3/4 PPH #2
S-MD 8-18 X 1 PPH #2
S-MD 8-18 X 1-1/2 PPH #2
S-MD 10-16 x 1/2 HWH #2
S-MD 10-16 x 3/4 HWH #2
S-MD 10-16 x 1 HWH #2
0.035
0.035
0.035
0.035
0.035
0.035
0.035
0.100
0.100
0.100
0.100
0.110
0.110
0.110
1/8
3/8
1/2
1
3/16
5/16
1/2
0.125
0.375
0.500
1.000
0.188
0.313
0.500
Socket
Recess
Box
Qty
1/4" 10000
1/4" 10000
1/4" 8000
PHL #2
PHL #2
PHL #2
PHL #2
5/16"
5/16"
5/16"
10000
10000
8000
5000
8500
6500
5000
Recommended Tools & Accessories see ordering information at bottom of page.
Medium Gauge Applications: Steel to Steel

U
Major applications
Liner panel/light gauge to frame
Sub-girt to interior steel profile
Stud assemblies/track to stud
Steel to framing/floor joists
Framing assemblies/trusses
HVAC duct fastening
Accessories (clips, electrical,
etc.) to purlin, girt or c-bars
Roof deck to bar joists or beams
Roof clips to bar joist
Lower profile head for above
mentioned applications (PPH )

min, in. / max, in.
Max. Thickness
Fastened (MF) in.
Socket
Recess
Box
Qty
Item No.
Description
00311450
00311451
00311452
00311453
00311454
S-MD 10-16x5/8 HWH #3*

S-MD 10-16x3/4 HWH #3*
S-MD 10-16x1 HWH #3
S-MD 10-16x1 1/4 HWH #3
S-MD 10-16x1 1/2 HWH #3
0.110
0.110
0.110
0.110
0.110
0.175
0.175
0.175
0.175
0.175
5/16
3/8
1/2
3/4
1
0.313
0.375
0.500
0.750
1.000
5/16"
5/16"
5/16"
5/16"
5/16"
7500
6500
5000
4000
4000
00311458
00311459
00311460
00311511
S-MD 12-14x3/4 HWH #3*

S-MD 12-14x1 HWH #3
S-MD 12-14x1 1/2 HWH #3
S-MD 12-14x2 HWH #3
0.110
0.110
0.110
0.110
0.210
0.210
0.210
0.210
5/16
1/2
1
1 1/2
0.313
0.500
1.000
1.500
5/16"
5/16"
5/16"
5/16"
5000
3000
2500
2000
00311461
00311462
00311463
00311464
S-MD 1/4-14x3/4 HWH #3

S-MD 1/4-14x1 HWH #3
S-MD 1/4-14x1 1/2 HWH #3
S-MD 1/4-14x2 HWH #3
0.110
0.110
0.110
0.110
0.220
0.220
0.220
0.220
5/16
1/2
1
1 1/2
0.313
0.500
1.000
1.500
3/8"
3/8"
3/8"
3/8"
4000
3000
2000
1000
00311455
00311456
00311457
S-MD 10-16x5/8 PPH #3*

S-MD 10-16x3/4 PPH #3
S-MD 10-16x1 PPH #3
0.110
0.110
0.110
0.175
0.175
0.175
5/16
3/8
5/8
0.313
0.375
0.625
PHL #2 7500
PHL #2 6500
PHL #2 5000
* Available in special Bulk quantities

Item No.
Description
00255932

00374640
00374641
00374708
Mag. Nut Setter 1/4" Short 00257258

Mag. Nut Setter 5/16" Shrt 00087102
#2 PHL TEK for PHL #2 (10) 00257257
Mag. Bit Holder Long

Mag. Bit Holder Long Brnze
Mag. Bit Holder Short
www.us.hilti.com
5.21
Light / Medium Gauge Applications: Steel to Steel
= Exposed
Exposed to weather

Item No.
Description
00311620
00311621
00311622
00311623
00311624
00311625
00311626
00311627
S-MD 12-14x3/4 HWH #3 Kwik seal

S-MD 12-14x1 HWH #3 Kwik seal
S-MD 12-14x1 1/4 HWH #3 Kwik seal
S-MD 12-14x1 1/2 HWH #3 Kwik seal
S-MD 12-14x2 HWH #3 Kwik seal
S-MD 1/4-14x3/4 HWH #3 Kwik Seal
S-MD 1/4-14x1 HWH #3 Kwik Seal
S-MD 1/4-14x1 1/2 HWH #3 Kwik Seal

min, in. / max, in.
0.035
0.035
0.035
0.035
0.035
0.110
0.110
0.110
0.187
0.187
0.187
0.187
0.187
0.250
0.250
0.250
Max. Thickness
Fastened (MF) in.
1/4
3/8
5/8
7/8
1 3/8
1/4
3/8
7/8
0.250
0.375
0.625
0.875
1.375
0.250
0.375
0.875
Socket
Recess
5/16"
5/16"
5/16"
5/16"
5/16"
3/8"
3/8"
3/8"
Box
Qty
3000
2500
2000
2000
1500
2500
2000
1500

Item No.
Description
00255932

00374641
00374642

Major applications
Pipe flashing/wall flashing
Exterior panel to girt
End lap-end cap/roof panel
to purlin
Outer wall panels/roof panel
blanket insulation to z-purlin
www.us.hilti.com
5.22

= Unexposed
= Exposed
Heavy Gauge Applications: Steel to Steel

U
Item No.
Description
00311613
00311614
00311616
00311617
00311618
00311615
S-MD 12-24x7/8 HWH #4

S-MD 12-24x1 1/4 HWH #4
S-MD 12-24x1 1/4 HWH #5
S-MD 12-24x2 HWH #5 KWIK COTE
S-MD 12-24x3 HWH #5
S-MD 12-24x1 1/4 HWH #5 KWIK COTE

min, in. / max, in.
0.175
0.175
0.250
0.250
0.250
0.250
0.312
0.312
0.500
0.500
0.500
0.500
Max. Thickness
Fastened (MF) in.
3/8
5/8
1/2
1 3/16
2 3/16
1/2
0.375
0.625
0.500
1.187
2.187
0.500
Socket
Recess
Box
Qty
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
4500
3500
4000
2000
1000
4000

Major applications
Roof deck/floor deck to
structural member
Panel/Panel clips to structural
member
Accessories (clips, etc.) to
structural members
Assembly of multiple layers
of metal to steel
Item No.
Description
00255932

00374641
Exposed to weather
E
Item No.
Major applications
Corrugated metal sheet to
structural member
Exterior decking and siding to
structural members
Assembly of multiple layers
of metal to steel
Description

min, in. / max, in.
00311628 S-MD 12-24x1 1/4HWH #5 KwikCote Bnd Wshr 0.250
0.500
Max. Thickness
Fastened (MF) in.
5/16
0.313
Socket
Recess
5/16"
Box
Qty
2500

Item No.
Description
00255932

00374641
www.us.hilti.com
5.23
Wood Drill Screws: Wood to Steel

Decking Screws
Item No.
Description

min, in. / max, in.
00311629
S-WD 8-18x1 5/16 PFH #3 BLK PHSPHTD 0.050
00311630
S-WD 8-18x1 15/16 PFH #3 BLK PHSPHTD 0.050
BLK PHSPHTD=Black Phosphated
0.140
0.140
Max. Thickness
Fastened (MF) in.
1/2
3/4
0.500
0.750
Socket
Recess
Box
Qty
PHL #2 6000
PHL #2 4000

Item No.
Description
00255940
00084143
00257258
00087102
00257257
#2 PHL TEK
Magnetic Bit Holder Long
Magnetic Bit Holder Long Bronze
Magnetic Bit Holder Short
Major applications
3/8" or 1/2" wood to steel
framing
Plywood to steel framing
Wafer Head Screws

Item No.
Description
00311632
00311633
00311634
S-WD 10-24x1 PWH #3

S-WD 10-24x1 1/4 PWH #3
S-WD 10-24x1 1/2 PWH #3

min, in. / max, in.
0.062
0.062
0.062
0.175
0.175
0.175
Max. Thickness
Fastened (MF) in.
5/8
7/8
1 1/8
0.625
0.875
1.125
Socket
Recess
Box
Qty
PHL #2 6000
PHL #2 5000
PHL #2 3500

Item No.
Description
00255940
00374708
00257258
#2 PHL TEK (10 Bits)

00087102
Major applications
3/8" or 1/2" wood to steel
framing
Wing Screws/Reamers
Item No.
Description
00311635
00311636
00311637
00311638
S-WW 10-24x1 7/16 PWH #3 wings

S-WW 12-24x2 PFH #4 wings
S-WW 12-24x2 1/2 PFH #4 wings
S-WW 1/4-20x2 3/4 PFH #4 wings

min, in. / max, in.
0.062
0.062
0.062
0.062
0.175
0.232
0.232
0.250
Max. Thickness
Fastened (MF) in.
3/4
1 1/4
1 5/8
2
0.750
1.250
1.625
2.000
Socket
Recess
PHL #2
PHL #3
PHL #3
PHL #3
Box
Qty
4000
2000
1500
1000

Item No.
Description
00255940
00374708
00374709
00257258
00087102
00257257

Major applications
(Minimum 16 ga base steel
required to break wings off)
Wood to steel member
2x4 to steel member
Truck trailer flooring
5.24
KWIK-FLEX Screws Keep Their Heads

While The Competition Loses Theirs From Hydrogen Embrittlement
KWIK-FLEX: the most significant innovation in screw fastening technology since the advent of the
self-drilling screw. While competitors are losing their heads" as a result of hydrogen embrittlement,
KWIK-FLEX screws keep performing even in hostile environments.
Advantages
Recommended for*
Virtually immune to embrittlement failure

Self-drilling for convenience, labor savings
KWIK-COTE finish provides corrosion resistance
even greater than zinc or cadmium plating
Complies with the Buy America Act
Aluminum to Steel
Fire Retardant Plywood
Corrosive Environments
Listings/Approvals
ICBO ES Evaluation Report #4780
COLA Research Report RR25095
Item No.

min, in.max, in.
Description
99638042
10-16 x 3/4 HWH #3
Recommended Tools
00255932 ST 18 Heavy Duty Tapper
0.035
0.150
Recommended Accessories
00374641 Magnetic Nut Setter 5/16" Short
1/2"

min, in.max, in.
Item No.
Description
00010354
10-24 x 1-1/4 PWH #3
Item No.
Description
0.062
0.175
0.062
0.187
00084143 #2 PHL TEK
00084148 #3 PHL TEK
00257258 Magnetic Bit Holder Long
00087102 Magnetic Bit Holder Long Bronze
00257257 Magnetic Bit Holder Short
3/4
Description
00087572
00087646
00087647
00008595
12 - 14 x 7/8 HWH #3
12 - 14 x 1 HWH #3
12 - 14 x 1 1/2 HWH #3
12 - 14 x 2 HWH #3
Item No.
Description
00087648
00087649
00008598
1/4 - 14 x 1 HWH #3
1/4 - 14 x 1 1/2 HWH #3
1/4 - 14 x 2 HWH #3
Item No.
Description
00000451
00000452
1/4 - 20 x 1 1/2 HWH #4

1/4 - 20 x 2 HWH #4
0.062
0.062
0.062
0.062
0.187
0.187
0.187
0.187
1/2
0.210
0.210
0.210
1/2
1/2
1
1 1/2
0.375
0.375
0.500
0.500
1.00
1.50
Max.Thickness
Fastened(MF)
15/32
15/16
1 7/16

min, in.max, in.
0.062
0.062
0.500
Max.Thickness
Fastened(MF)

min, in.max, in.
0.062
0.062
0.062
0.750
Max.Thickness
Fastened(MF)

min, in.max, in.
Item No.
0.500
Max.Thickness
Fastened(MF)

min, in.max, in.
00010355
12-14 x 1 PFHUC #3
Recommended Tools
00255940 SU 25 Universal Screwdriver
Recommended Tools
00255932 ST-18 Heavy Duty Tapper
Max.Thickness
Fastened(MF)
0.460
0.950
1.450
Max.Thickness
Fastened(MF)
13/16
1 5/16
0.830
1.300
Socket
Recess
Box
Qty
5/16"
6000
Socket
Recess
Box
Qty
PHL #2
5000
Socket
Recess
Box
Qty
PHL #3
4000
Socket
Recess
Box
Qty
5/16"
5/16"
5/16"
5/16"
5000
4000
2500
2000
Socket
Recess
Box
Qty
3/8"
3/8"
3/8"
3000
2000
1500
Socket
Recess
Box
Qty
3/8"
3/8"
2000
1500
* These fasteners address delayed failures due to hydrogen embrittlement. They are NOT any more resistant to corrosion than our standard Kwik-Coted screws.
www.us.hilti.com
5.25
Roofing Screws
Screws For the Fastening of Insulation to Structural Roof Decks

#10 Std. Steel Deck Screws
Also available in Hex Washer Head
Description
Item No.
10 x 1 5/8 RS MPTH
10 x 2 1/4 RS MPTH
10 x 2 7/8 RS MPTH
10 x 3 3/4 RS MPTH
10 x 4 1/2 RS MPTH
10 x 6 RS MPTH
96092066
96092067
96092068
96092070
96092071
96092073
Thread Length
Box Qty
Recommended Installation System
FULL
FULL
FULL
3"
3"
3"
1000
1000
1000
1000
1000
1000
ST-18 SCREW DRIVER

KT POWER BIT #3 PHL-4"
#12 Heavy-Duty All-Purpose Deck Screws

Also available in Hex Washer Head and as 410 SS.
Description
Item No.
12 x 1 5/8 RS MPTH
12 x 2 1/4 RS MPTH
12 x 2 7/8 RS MPTH
12 x 3 1/4 RS MPTH
12 x 3 3/4 RS MPTH
12 x 4 1/2 RS MPTH
12 x 5 RS MPTH
12 X 6 RS MPTH
12 X 7 RS MPTH
12 X 8 RS MPTH
96087232
96087233
96087234
96087235
96087236
96087237
96087238
96087239
96087240
96087241
Thread Length
Box Qty
FULL
FULL
FULL
3"
3"
3"
3"
4"
4"
4"
1000
1000
1000
1000
1000
1000
1000
1000
500
500
ST-18 SCREW DRIVER

--FOR CONCRETE DECKS-TE-15 HAMMER DRILL
3/16" DIAMETER
MATCHED TOLERANCE
DRILL BIT
#14 Heavy-Duty All-Purpose Deck Screws

Also available in Hex Washer Head.
Description
Item No.
14 x 1 5/8 RS MPTH
14 x 2 1/4 RS MPTH
14 x 3 1/4 RS MPTH
14 x 4 1/4 RS MPTH
14 X 5 RS MPTH
14 x 6 RS MPTH
14 X 8 RS MPTH
14 x 10 RS MPTH
14 x 12 RS MPTH
14 x 7 RS MPTH
14 x 9 RS MPTH
14 x 11 RS MPTH
96010233
96010235
96010237
96010239
96010240
96010241
96010243
96087260
96087262
96010242
96087259
96087261
Thread Length
Box Qty
FULL
FULL
3"
3"
3"
4"
4"
4"
4"
4"
4"
4"
1000
1000
1000
1000
1000
1000
500
500
500
500
500
500
ST-18 SCREW DRIVER

--FOR CONCRETE DECKS-TE-15 HAMMER DRILL
7/32" DIAMETER
MATCHED TOLERANCE
DRILL BIT
Tap-Fast Screws A #10 ROOF SCREW WITH A FLO-SEAL HEAD. IDEAL FOR METAL TO WOOD CONSTRUCTION. USES 1/4" NUT SETTER.
Description
Item No.
10-12 X 1 HWH TAPFAST

10-12 X 1 1/2 HWH TAPFAST
10-12 X 2 1/2 HWH TAPFAST
00010226
00010228
00010230
00010231
00010232
Decking Screws (Coated Course Thread)

Description
Item No.
6 X 1 1/4 PBHS DECKING

6 X 2 PBHS DECKING
8 X 3 PBHS DECKING
00010196
96010198
00010215
00010222
00010224
Thread Length
Box Qty
1"
1 1/2"
2"
2 1/2"
3"
3000
2500
1500
1000
800
IDEAL FOR WOOD TO WOOD CONSTRUCTION.

Thread Length
Box Qty
1 1/4"
1 5/8"
1 5/8"
1 5/8"
1 5/8"
8000
5000
3500
2500
2000
www.us.hilti.com
5.26
Accessories
Accessories
Insert Bit Package
NEW!
Item No.
Description
00374632
Professional bit kit
containing: magnetic bit holder long, Phillips bits: 3xPH1,

10xPH2, 3xPH3, square bits: 4xSQ1, 7xSQ2, Slotted bits:
1xSL6, 1xSL8, 1xSL12, nut setters: 1x1/4", 1X5/16", 1X3/8"
00374636
Insert bit pocket pack
containing: magnetic bit holder with locking sleeve, Phillips

bits: 1xPH1, 2xPH2, 1xPH3, square bits: 1xSQ1, 2xSQ2, Slotted
bits: 1xSL6, 1xSL8
Insert Bits
$$
Saitvhesp$ecial
ricin
P
k
l
u
B
w
g!
Ask your Hilti Sales Person

or Customer Service Representative
for details
Item No.
Description
00374702
00374703
00374706
00374708
00374711
#1 PHL Drywall
#2 PHL Drywall
#1 PHL TEK
#2 PHL TEK
#3 PHL TEK
Package Qty
10 pcs
10 pcs
10 pcs
10 pcs
10 pcs
Item No.
Description
00374682
00374683
#1 SQDRV
#2 SQDRV
Package Qty
Item No.
Description
00084165
00084167
00084169
00374728
00274730
00084175
00374733
3F-4R SLTD (0.032" x 5/32")

4F-5R SLTD (0.034" x 3/16")
5F-6R SLTD (0.036" x 7/32")
6F-8R SLTD (0.040" x 1/4")
8F-10R SLTD (0.042" x 9/32")
10F-12R SLTD (0.046" x 9/32")
12F-14R SLTD (0.050" x 9/32")
10 pcs
10 pcs
Package Qty
Insert Bit Holders

Item No.
Description
00257258
00084126
00087102
00257257
Magnetic Bit Holder Long 2-1/4 Standard

Non Magnetic Bit Holder Short
Magnetic Bit Holder Long Bronze 2-1/2 Standard
Item No. (Single)
Item No. (5 Pack)
Description
00084179
00084183
00084195
00084181
00084191
00084197
00374696
00374698
00374700
00374692
#1 PHL Short
#2 PHL Short
#3 PHL Short
#1 PHL Long
#2 PHL Long
#3 PHL Long
Item No. (Single)
Item No. (5 Pack)
Description
00084199
00084203
00084201
00084205
00374684
00374686
#1 SQDRV Short
#2 SQDRV Short
#1 SQDRV Long
#2 SQDRV Long
Power Bits
Magnetic Nut Setter
www.us.hilti.com
5.27
Item No.
Description
00374640
00374641
00374642
00084221

1
1
10
10
1
10
Accessories
Insta-Back Drywall Fastener

Industrys Only Fire-Rated Drywall Repair System Saves Time and Material,
Eliminates Deformation
The 1992 supplement to the
Uniform Fire Code (Sec. 10.601)
requires that when fire-rated
gypsum walls or ceilings are
broken to the extent that through
openings exist, the damaged
wallboard must be replaced or
returned to the required level of fire
resistance using a listed repair
system.
At this date, Hilti's easy to use
Insta-Back system is the only
repair system so listed.
Advantages
Listings/Approvals:
ICBO (International Conference
of Building Officials)
Report No. 2451
SBCCI (Southern Building Code

Congress International)
Report No. 95109
BOCA (Building Officials Code

Administrators
Report No. 88-13 approval
Tested in accordance with

ASTM E119 fire criteria
ASTM E72-77 shear wall
requirement
Eliminates time consuming measuring and cutting, reduces scrap in

both repair jobs and new installations
No special tools required
Eliminates ridging or crowning in long walls
Permits faster,easier ceiling installation
Assures strong, clean and accurate installation
Installation Instructions
1. Position Insta-Back
clip as per product
instructions.
2. Join drywall over

clips.
3. Break off tabs.
Item No.
Description
00068450
00068454
Insta-Back Fastener 1/2"

Box Qty
200
200
www.us.hilti.com
5.28
NEW
Hilti GX 100 Gas-Driven Fastening Tool
Charge Up
Your Work,
Not your BaNttoery
Batteries. to ECVhaErgR.e.
See page 6.15

Short Fastener Tools
NEW !
DX 35
DX 351
GX 100
Page 6.12
Page 6.13
Page 6.15
Long Fastener Tools
NEW !
DX E72
DX 36M
DX 460
Page 6.11
Page 6.16
Page 6.17
Sprinkler Stud Tools

DX 600N
DX A41 I
Page 6.20
Page 6.19
Pneumatic Fastening Tool

R4DW-X Pneumatic Fastener
Page 6.18
Grating Fastening Tool

DX A40 Grating Tool
DX 750 Grating Tool
Page 6.21
Page 6.22
Identification & Marking

DX A40 HM
DX A40 CM
Page 6.28
Page 6.28
Steel Deck Fastening Tools

NEW !
DX 460 SM
R4X12
DX 750 Standard
DX 750 MX
DX A70 ROOFIX
Page 6.23
Page 6.24
Page 6.25
Page 6.25
Page 6.26
Fasteners
Online Decking Design Center

www.us.hilti.com/steeldeckingdc
www.us.hilti.com
Fastener Overview
Drywall/Lathing
Acoustical Ceilings
Electrical Clamps/Clips
Cable & Rod Hangers
HVAC Duct Straps
Hardwood Flooring
Insulation/EIFS
Steel Deck (Structural Steel)
Steel Deck (Bar Joist)
Grating/Checkerplate
Forming Work
Sill Plate
Sprinkler
Page 6.6+
Page 6.37+
Page 6.40
Page 6.41
Page 6.41
Page 6.42
Page 6.6
Page 6.39
Page 6.25
Page 6.23
Page 6.21+
Page 6.37+
Page 6.37+
Page 6.20
System
Tool Description
Application
Page
DX 35
Semi-automatic powder actuated tool for

medium to high volume applications, fastening
many types of pins, studs, clips and clip
assemblies.
This tool fastens pins from 1/2"to 1-1/2"
(14 mm to 37 mm) to concrete, steel and
other suitable base materials. There is also a
pole tool available for ceiling applications.
Drywall track and hat

channel
Angle track
Electrical clips, clamps and
boxes
EMTC conduit clips
HVAC duct straps
Acoustical ceilings
6.12
DX 351
Lightweight, fully-automatic powder-actuated

tool designed for interior finishing and
mechanical/electrical applications (drywall
track, ceiling clip assemblies, cable hangers)
As a single fastener tool the DX 351E can
fasten pins 1/2" to 1-3/4" (14mm to 47mm)
This tool has a high fastener driving rate up
to 700 pins per hour with MX 32 magazine.
The magazine uses collated fasteners
1/2" to 1-3/4"
6.13
Fully automatic, gas-driven fastening tool

designed specifically for interior finishing
applications (drywall track, hat track, angle
track). The GX 100 utilizes a wide range of
fasteners from 1/2" to 1-5/8" in length.
(14 to 39 mm).
The GX 100 system is the only gas-driven
system capable of fastening at a high rate of
speed into concrete, steel, and concrete block
without the use of a rechargeable battery.
Drywall track
Hat track
Angle track
6.15
DX E72
Single .22 caliber powder actuated tool for

light to medium duty fastenings, designed for
easy handling and dependability.
This tool fastens pins from 1/2"to 2-7/8"
(14 mm to 72 mm) to concrete, steel and
other suitable base materials.
Forming work
Sillplate
boxes
EMTC and other conduit
clips
HVAC duct straps
6.11
DX 36M
The worlds best selling semi-automatic

powder actuated tool. Fastens over 140
different sizes of Hilti fasteners, clips and
threaded studs.
This single shot tool fastens pins from
1/2" to 2-7/8" (14 mm to 72 mm) to concrete,
steel and other suitable base materials.
Drywall track and hat track

Angle track
Forming work (2 x 4,etc.)
Hardwood flooring
Sillplate
boxes
HVAC duct straps
Acoustical ceilings
Insulation/EIFS
6.16
DX 460 MX 72
Fully automatic powder actuated tool.

Provides speed, versatility and reliability to a
wide range of jobsite applications. This fully
automatic tool fastener pins from 1/2" to
2-7/8" (14 mm to 72 mm) to concrete, steel,
and other suitable base materials.
6.17
DX 351 MX 32 (shown)
GX 100
Long Fastener Tools
NEW!
NEW!
6.3
Drywall Track
Hat track, angle track
HVAC duct straps
EMTC conduit clips
Acoustical ceilings
Electrical boxes
Telecom cable hangers
Sillplate
Forming work
Hardwood flooring
Drywall track
Angle track
Water prooing
Electrical clips
HVAC duct straps
Insuulation/EIFS
Acouustical ceilings
System
Tool Description
Applications
Page
R4DW-X
Pneumatic
Fastener
High production pneumatic tool with fastener

length capacity of 5/8" to 2-1/2" collated in
strips of 10.
Magazine capacity of 30 nails.
Drywall track to concrete

Hardwood floors
Metal to concrete/steel
Wood to concrete/steel
6.18
DX A41 I
High power, fully automatic, single fastener

powder actuated tool. Fastens 3/8" studs and
10 mm washered nails to concrete, pandeck.
This tool also fastens 10 mm washered pins
with lengths from 3/4" to 2-7/8" (19 mm to
72 mm) to concrete, steel and other suitable
base materials.
Sprinkler pipe hangers

Most 10 mm washered pin
applications
6.19
DX 600N
Heavy-duty, single fastener powder actuated

tool. Fastens all 3/8" studs and 10 mm nails
to high strength steel and concrete.
This tool fastens 10 mm washered pins with
lengths from 3/4" to 2-3/4" (19 mm to 72 mm)
to concrete, steel and other suitable base
materials.
Sprinkler pipe hangers

Any 10 mm washered pin
application
6.20
DX A40 Grating Tool
The DX A40 automatic grating tool fastens

standard and stainless steel studs for grating
and checkerplate disks for many styles of
open-bar grating and checkerplate.
Grating
Checkerplate
6.21
DX A40 HM
The DX A40 HM is a fully automatic, powder

actuated tool that is for use in hot or cold
marking applications.
The DX A40 HM can be used on most metal
types where specification and/or identification
marks are required.
Marking
Identification stamping
6.28
The DX A40 CM is a fully automatic, powder

actuated tool for use in cold marking
applications.
The DX A40 CM can be used on pipe (with
centering device) and most cold metal types
where specification and/or identification marks
are required.
Marking
Identification stamping
DX A40 CM
Stamping on:
Finished/semi-finished metal
Castings
6.28
Stamping on:
Cold Metal
Finished/semi-finished metal
Castings
6.4

System
Tool Description
Applications
Page
The lightweight Hilti DX 460 SM powderactuated tool gives you outstanding mobility
and increased comfort.
With integrated power regulation, you can
count on consistent, accurate fastenings for
siding and decking applications, with a driving
rate of up to 700 fastenings per hour.
Fastening metal decking to

bar joists
6.23
R4X12
Pneumatic tool with high fastening rate for

steel decking applications. 20 nail magazine
using high shear fasteners collated in strips of
10 for high volume and productivity.
Steel deck and form deck

to bar joist 1/8" up to 3/8"
thick
6.24
DX 750 Standard
Specialty semi-automatic powder actuated tool

for medium and heavy-duty decking and
siding. With conversion sets, the tool can be
changed for a variety of applications.
Interchangeable parts allow

the tool to be changed for the
following applications:
Decking (magazine)
Grating/checkerplate
Shear connection
General fastenings to
concrete and steel
6.25
DX 750 MX
Specialty semi-automatic powder actuated tool

for medium and heavy-duty deck fastening.
The MX magazine eliminates the handling of
single pins, providing a capacity of 10 strip
boosters and nails.
Steel deck attachment to

structural steel
6.25
DX A70 R
ROOFIX
Fully automatic tool for use in fastening profiled

metal deck to structural steel 1/4" and greater.
By utilizing a magazine capacity of 40 nails and
boosters, the DX A70 R provides speed and
performance in decking applications up to
1200 fastenings per hour.
Steel deck attachment to

structural steel
6.26
DX 460 SM
NEW!
Steel & Decking

Design Center
Online Decking Design Center
www.us.hilti.com/steeldeckingdc
6.5
Get product info and technical data

online for bar joist and structural
steel applications or go directly to
diaphragm tables.
Download the latest version of the
Hilti Decking Program for
calculating diaphragm shear
capacities. All calculations are in
accordance with the Steel Deck
Institute Diaphragm Design Manual.
Additional online resources:

Technical Papers
Project References
Guide Specifications
Decking CAD Details
UL Roof Deck Constructions
FAQs
Direct Fastening Terminology (.PDF)
Decking Terminology (.PDF)

Fastener
DX E37
DX 35
DX 351E
DX E72
DX 350
DX 460
DX 36M
R4DW-X
DX 351
DX 460 with
Magazined Tool AM72 Mag.
X-ZF22
X-ZF20
(MX)
(MX)
(MX)
(MX)
ESD16
CC-27-AL
X-RH (Wall mount)
X-RH (Ceiling mount)
X-DW
(Available with
pre-tied wires)
CC-27-ZF
(Available with
pre-tied wires)
ECH
X-HS
EMTC-ZF
X-DNI
Cable & Rod Hangers
X-JH (Ceiling mount)
HVAC Duct Straps
X-CR/
X-CRW6
X-ZF
Hardwood Flooring
Electrical Clamps/Clips
Acoustical Ceilings
Drywall/Lathing
Application
X-ZF
X-DNI
X-JH (Wall mount)
X-HS
X-DNI
X-AL
MX
Pins
6.6
Insulation/EIFS
Application / Fastener
DX 350
Steel Deck (Structural Steel)

Steel Deck (Bar Joist)
DX 460 XIE
DX 351
R4X12
DX 460 MX SM
X-IE
X-SW 30
Grating/Checkerplate
DX 460
DX 36M
DX A40
Grating
DX 750 with
Grating
Conversion
DX 750 MX DX 750
ENP2/ENPH2
MX Pins
MXR Pins
EDNI9 HSN M
EDNK22 HSN M
X-ZF22 FDN M
DX A70 R
X-FCM
X-FCP
X-CRM
6.7
Forming Work
Application / Fastener
DX 350
DX 460
DX A41 I
DX 600N
Sill Plate
DX 36M
DX E72
EW10
W10
X-ZF
X-CF
SL, SL MX
X-ZF
X-CF
Sprinkler
DX A40 HM
DX A40 CM
X-ZF MX Pins
Identification
DX 460 MX
(with washer
holder)
Marking
Characters
6.8
6.9
Powder Actuated Fasteners
Superior Fastener Technology From Hilti

Hilti X-AL-H : Highest Strength Nail
Specially hardened material
providing maximum strength for driving into
hard materials.
Raised head
designed to mate
perfectly with the
piston tip which
provides optimal
guidance
Rigid washer material for

superior guidance in the nail
channel
Head stamped
with letter "H"
High performance ballistic point

for easier penetration into very hard
concrete or steel
Zinc plated
for easier identification

and inspection
High Performance
X-AL-H Series
A hardened powder actuated fastener
with high application limits for high
strength concrete and steel.
Product Features
Use X-AL fasteners for hard base
materials
For concrete up to 7200 psi
For steel up to A572/Grade 50
Special design nail point for
maximum penetration
Optimal head guidance for lowest
failure rate
Specially heat-treated
high-strength steel
Zinc plated
Key Applications
Renovation of old buildings

Pre-cast buildings/parking garages
Bridges
Steel Building
(Structural members)
Tilt-wall building construction
Any project where standard
fasteners do not perform properly
Lengths
Universal
X-DNI/EDNI Series
A top quality nail for most applications
in concrete and steel.
Product Features
Proven universal application
fastener
Zinc plated
Ballistic point for better
performance
Available in collated strips of 10
Key Applications
Cables and electrical pipe

Masonry ties and forms
Electrical components
HVAC Duct straps
Plywood to concrete
Thin materials to steel
Door frames to concrete
Window mullions
Hardwood flooring
Drywall Track
X-DW Series
Standard Quality
X-ZF Series
A high-quality nail for fastening drywall

track to concrete and block (CMU).
Product Features
Specifically designed to require
less driving energy (reduced
recoil and noise)
Zinc plated
Available in collated
strips of 10
A standard quality nail for fastenings

into concrete and steel.
Product Features
Lengths
Suitable for most standard

fastenings
Ideal for nailing to new concrete
Zinc plated
Available in many configurations
- with plastic or metal tophat
- with pre-mounted washers
- with pre-mounted clips and clamps
- collated strips of 10
3/4" to 1-5/8" (20 mm to 39 mm)
Key Applications
Key Applications
Drywall trackconcrete
and block
Hat track concrete and block
Lengths
7/16" to 2-7/8" (12 mm to 72 mm)
MX Collated Pins
7/16" to 2-7/8" (12 mm to 72 mm)
Concrete form work

Drywall track concrete and steel
Wood sill plates to concrete
Basket clips
Safety barriers
Metal sheeting to concrete or steel
Lengths
1/2" to 2-7/8" (14 mm to 72 mm)
ADDED
VALUE
$16,000 project labor savings using Hilti DX AL pins to

attach electrical boxes to concrete walls versus pre-drilling
and anchoring with plastic screw anchors.
www.us.hilti.com
6.10
Powder Actuated Fasteners
Specialty Fasteners
Stainless Steel : X-CR Series
The worlds first and only powder actuated

stainless steel fastener corrosion resistance
equivalent to 316 stainless steel.
Product Features
Great performance tested at almost three
times higher stress than 316 SS
High level of corrosion protectionoutperforms 316 SS in salt spray test
Selected sizes of threaded studs available
Five times faster than drilling or screw
fastening
For concrete or steel
Limited Purpose : X-CF Series
An economical nail made specifically for

repetitive 2x4 fastenings to new concrete.
Product Features
Black lacquered coating for temporary
fastening or interior applications
Suitable for fastening into green concrete
Available in two lengths 2-1/2" and 2-7/8"
with pre-mounted steel washer
Ideal for concrete form work and
residential sill plates
Removable : SL Nails
A breakaway fastener for temporary forming

applications.
Product Features
Special head shape allows wood to
be pulled over with minor damage
3 Predetermined breaking points
2 plastic washer assures guidance
Available in collated strips of 10
Insulation Fastening : X-IE
An insulation fastener that consists of a

plastic section and a pre-fitted hardened nail.
Product Features
Fasten most kind of insulation
25 mm to 120 mm thick
Fastener resistant to aging and rotting
High holding power
Fasten to different base materials like
concrete, steel, masonry, plastered masonry
Non compression of insulating material
Sheeting/Insulation Fastening : X-SW
A soft washer for fastening thin sheeting and

insulating material less than 30 mm thick.
Product Features
2 washer sizes 30 mm and 60 mm
Soft washer protect material
against damage
Adapts to the shape of the fastened material
1 preassembled component with nail
Key Applications & Projects
Exterior Applications
Water Treatment
Food Processing
Paper Mills
Chemical Plants
Industrial Plants
Tunnels/Highway Bridges
Tank Linings
Lengths
1/2" to 2-1/8" (14 mm to 54 mm)
Key Applications
Residential sill plate attachment
to concrete
Concrete form work
Attachment of 2x4 to concrete
Lengths
2-1/2", 2-7/8"
Key Applications
Fastening of baseboards, stop and
offcuts to secure jacks
Fastening of guide boards and nailers
for wall, column and step forming
Barriers and safety installations
securing and protecting hoses
or cables against slipping
or mechanical damage
Key Applications
Attach styrofoam or EIFS insuulation panels
to concrete
Curtain wall cladding/facades, warehouses
and cold stores, separations and joints,
acoustic insulation
Lengths
Nail: 1-1/2" to 2-7/8" (37 mm to 72 mm)
Insulation thickness: 1" to 4-3/4"
(25 mm to 120 mm)
Key Applications
Sheeting, drainage panel
Separating and joint insulation
Insulation materials
Plastic corrugated sheeting
Netting
Pin Lengths
1-1/2" to 2-1/2" (37 mm to 62 mm)
www.us.hilti.com
6.11
Long Fastener Tools
DX E72 Powder Actuated Fastening Tool

Hiltis Versatile Single Load .22 cal.
Technical Data
Dimensions (LxWxH)
15.0" x 1.8" x 6.0"
Weight
4.5 lb
Working principle
Impact piston
Piston bore
8 mm
Boosters/Power Levels
Gray (1)
Brown (2)
Green (3)
Yellow (4)
Fastener range
1/2" to 2-7/8" (14 mm to 72 mm)
Approvals
Meets ANSI standard A 10.3 and
OSHA requirements
Advantages
Quick, economical and universal fastenings to concrete and steel

Practical single-hand cycling
Piston and stop ring change without using a tool
Very little cleaning or servicing
Hand protected by enclosed grip
Operator and function safety
Practical and handy kit box
R e p a i r
P r o g r a m
Contact your Hilti Sales

Representative for details.
Item No.
Description
00001092
DX E72 Deluxe
Deluxe kit supplied in impact resistant plastic carrying case
with accessories (spare parts package, ejection rod, rubber
stabilizer, round brush, cleaning cloth, spray lubricant),
safety goggles and operating instructions.
Booster Cartridge (5.6 x 16 mm) .22 Caliber

Item No.
Description
00050395
00050396
00050397
00050398
.22 CAL Gray

.22 CAL Brown
.22 CAL Green
.22 CAL Yellow
Box Qty
100
100
100
100
www.us.hilti.com
6.12

Technical Data
Dimensions (LxWxH)
11.25" x 1.8" x 5.6"
DX 35 Drywall Track Installation Tool

Lightweight, Fast And Reliable
Weight
4.25 lb
Working principle
Impact
Piston bore
8mm
Boosters
Hilti .25 caliber short in white plastic
strips of 10
Power Levels
Green (3)
Yellow (4)
Red (5)
Fastener range
1/2" to 1-1/2" (14mm to 37mm)
Fasteners
X-CR, X-AL, X-DNI, X-EDNI, X-ZF, ESD,
X-DW
Assemblies
Ceiling clips, conduit clips, CTV clips
Approvals
OSHA requirements
R e p a i r
P r o g r a m

Advantages
Specially designed for drywall and acoustical applications

High speed, high volume in light duty applications
Semi-automatic booster advance
Ten-booster strip in three power levels
Pole tool available for overhead work
Drives pins from 1/2" to 1-1/2" (14 mm to 37 mm)
Various baseplates aid in reaching limited access areas
Item No.
Description
00002506
DX35 tool in deluxe kit box

Deluxe kit supplied in impact resistant plastic carrying case
with accessories (spare parts package, rubber stabilizer,
cleaning brushes, spray lubricant), safety goggles and
operating instructions.
Booster Cartridge .25 Caliber

Item No.
Description
00050106
00050107
00050108
.25 CAL Green

.25 CAL Yellow
.25 CAL Red
Box Qty
100
100
100
Replacement Parts
00002565
Piston 21/SDF
00002556
Base plate 21/S1
00002554
Fastener guide 21/F3-1
X-PT 35 Modular Pole Tool

Advantages:
www.us.hilti.com
Pole Tool see page:
6.32
6.13
Variable, modular length (4' to 13')

Rugged and durable construction
Eliminates need for scaffolding
Reduces operator fatigue
Easy jobsite storage
Can be used with DX 35 and DX 350
your
Extenadch!
re
Applications
Acoustical ceilings
DX 351 Powder Actuated Fastening System

Boost Your Productivity: Fully Automatic Up to 700 Fastenings Per Hour!
16"
Quick
Lightweight, fully automatic powder-actuated tool
designed primarily for interior finish and
mechanical/electrical applications (drywall track,
ceiling clip assemblies, conduit, cable hangers)
Collated pins and boosters reduce reloading time
High fastener driving rate up to 700 pins per hour!
Comfortable
Quick Change
The MX Magazine answers
your need for speed letting
you fasten up to 700 pins
per hour! With the simple
push-in system, reloading
is quick and easy.
2" x 6-1/4"
Length (with or without

magazine)
Advantages
Technical Data
Dimensions (WxH)
Extremely light and compact

Ideal for repetitive applications and overhead use
Low recoil
Low noise level
Versatile
Weight
5 lb
Boosters
10-booster plastic strip .27 cal. short
Power level
White (2)
Green (3)
Yellow (4)
Red (5)
Pin range (with fastener

magazine)
1/2" to 1-1/4" (14 mm to 32 mm)
Pin range (without fastener

magazine)
1/2" to 1-7/8" (14 mm to 47 mm)
For use on a wide variety of base materials

Applications: track, hat track, angle track, ceiling clips,
conduit clips, HVAC duct strips
Fastener driving power regulation
Item No.
Description
00373103
DX 351E Single Baseplate Tool
Shown
R e p a i r
Supplied in an impact-resistant plastic carrying case with

accessories (ECH hanger adapter, extra piston, safety
goggles, cleaning brushes, cleaning cloth, Hilti spray and
operating instructions)
00374308
DX 351W/MX32 Magazine
Supplied in an impact-resistant plastic carrying case with

accessories (extra piston, safety goggles, cleaning brushes,
cleaning cloth, Hilti spray and operating instructions
00377826
P r o g r a m

DX 351 W/MX 32 Magazine & Single Baseplate Tool
10-booster (.27 caliber short mag.) strips for DX 351

Item No.
Description
Power level
00333317
00247446
00004841
00004842
3/90MA white
3/110MA green
3/130MA yellow
3/220MA red
Extra light
Light
Medium
Heavy
Box quantity
1000
1000
1000
1000
Accessories & Spare parts (not shown)

Item No.
Description
00333315
00339474
00331300
00331047
00331194
00331206
00331193
00332579
X-MX27 Magazine* 1"(27 mm) capacity

X-MX32 Magazine 1-1/4" (32 mm) capacity
X-FG8ME-351 Standard baseplate
X-P8S-351 Standard piston
X-P8AL-351 Piston for AL type pins
X-FG8L-351 Narrow baseplate
X-P8L-351 Narrow baseplate piston
DX 351 tool case
* Note: this magazine must be used only with a Hilti DX 351.

** Note: DX 351 Pole tool uses same grip section as the X-PTA and X-PT35/350 modular pole tools.
X-PT 351 Modular Pole Tool

Advantages:
Variable, modular length (4' to 13')

Easy jobsite storage
your
d
n
e
t
x
E ach!
re
Applications
Acoustical ceilings
www.us.hilti.com
Pole Tool see page:
6.32
6.14
Short Fastener Tool

Charge Up Your Work. Not Your Batteries.
No
B
atte
to Charger. y
The Right System for All Your Interior Finishing Fastening Needs. GX 100
The new high-performance system from Hilti with no battery to charge. Ever.
EVER.
Technical Data
Dimensions (LxWxH)
Advantages
Convenient No battery to charge
Reliable Fasten into steel & hard concrete with ease & confidence
Versatile Wide range of applications and consumables
Fast You be the judge
16.75" x 6.9" x 14.6"
Magazine Capacity
40 collated fasteners
Tool weight
9.15 lb Loaded with fasteners
Power Source
GC 12 (gas canister)
Fastener Range
1/2" to 1-5/8"
Easily Fasten Into

Steel & Hard
Concrete
Steel
For beams and columns
Repetitive fastening of metal track
and hat-track, Z brackets and slip
track
Concrete
For floors, walls and ceilings
Repetitive fastening of metal
track,hat-track and wood
Metal profile fastening to walls for
suspended ceilings
Concrete Block
Fastening of metal track and hat-track
GX 100 Gas-Driven Fastening System
Item No.
Description
00338047
GX 100 Gas-Driven Fastening Tool
Supplied in an impact resistant plastic Hilti case with

attachable support leg, ear protectors, safety glasses,
cleaning cloth and operating instruction manual.
Accessories
Item No.
Description
00378586
00378587
00378588
00379693
X-GM 40 Nail Magazine

X-100 SL Support Leg
X-100 TN Nosepiece
GC12 Gas Canister (750 fastenings)
Item No.
Description
00338872
00340227
00338875
00340229
00338878
00338881
X-EGN 14MX Combo

X-GHP 18MX Combo
X-GN 20MX Combo
X-GN 27MX Combo
X-GN 32MX Combo
X-GN 39MX Combo
1/2"
11/16"
3/4"
1"
1-1/4"
1-9/16"
Fasteners Package content: 750 pins (collated in strips of 10)

Nail
Length (in.)
Typical Base Material
Steel
Hard Concrete
Concrete
Concrete and Block
Concrete and Block
Concrete and Block
www.us.hilti.com
6.15
Long Fastener Tools
DX 36M Fastening System
Technical Data
Dimensions (LxWxH)
Faster Nailing, Easier to Use, and Greater Operator Comfort
14.5" x 1.9" x 6"
Weight
5.3 lb
Working principle
Impact
Piston bore
8 mm
Boosters
Hilti .27 caliber short in plastic strips
of 10
Power Level
Green (3)
Yellow (4)
Red (5)
Fastener range
1/2" to 2-7/8" (14 mm to 72 mm)
Fasteners
Booster Power Regulator
DX 36M comes with a booster
power regulator, allowing the right
amount of power for the job.
X-CR, X-AL-H, X-DNI, X-EDNI,

X-ZF (MX), X-CF, X-IE, (E)W6-P8,
ESD, X-EDNK, X-SW, SL
Assemblies
Ceiling clips, conduit clips, basket
clips, gunite clips
Approvals
Advantages

OSHA requirements
10-booster semi-automatic advance

Booster power regulator provides variable power
choices for accurate nail driving
Durable construction, proven dependability
Pole Tool available for ceiling applications
Versatile, drives wide range of fasteners
R e p a i r
Item No.
Description
00003690
DX 36M Deluxe
P r o g r a m

Deluxe kit supplied in impact resistant Hilti case

with accessories (safety glasses, cleaning cloth, brushes,
spray lubricant) and operating instructions
Booster .27 Caliber

Item No.
Description
00247446
00004841
00004842
.27 CAL Green

.27 CAL Yellow
.27 CAL Red
Box Qty
100
100
100
PT-36M II Pole Tool

Advantages
Increases productivity
Enables DX 36M to be used with
Hilti pre-tied ceiling clips
Item No.
Description
00338759
00003295
PT-36M Modular Pole Tool

DX 36M with Pole Tool Adapter
Extend your
reach!
Length
7'
www.us.hilti.com
6.16
Long Fastener Tools

Technical Data
Weight
7.78 lb (3.53 kg) incl. magazine
DX 460 Fully Automatic Powder Tool

The Fast Versatile Powder Tool System for a Variety of Applications
NEW!
Tool length
18.11 in. (460 mm)
Magazine capacity
fasteners in magazine strips of 10,
lengths 1/2" to 2-7/8" (14 to 72 mm)
Cartridges
6.8/11 M, in magazine strips of 10,
4 power levels (green, yellow, red,
purple)
Fastener Range
1/2" to 2-7/8"
R e p a i r
P r o g r a m

Advantages
Safety
Reliability
The well-proven Hilti piston principle and a whole

range of other safety devices help provide user
protection.
This system has endured countless months of jobsite

and laboratory testing to ensure a long life
expectancy, especially in high production use.
Versatility
Whether fastening thick or thin materials to concrete
or steel, the power regulation, variety of cartridge
power levels, and wide range of fastener lengths
permit consistent fastenings over a large array of
applications.
User-friendliness
The ergonomic design and padded grip dramatically
increase comfort, while the new magazine makes
loading and fastening a breeze.
Speed
A durable magazine combined with the automatic
piston return system assures you of a tremendous
number of fastenings in even less time without any
manual cycling of the tool.
Item No.
Description
00370448
DX 460 tool complete with MX72 magazine

With impact-resistant plastic toolbox, single fastener guide,
spare piston, cleaning set, spare buffer, ear protectors, safety
glasses and Hilti lubricant spray.
00372830
DX 460 Deluxe Single Baseplate Tool
Cartridges (strips of 10)
Item No.
Package contents
Description
00247446
Light
00004841
Medium
00004842
Heavy
00004843
Extra-heavy
Spare parts for the DX 460
Power
1000
1000
1000
1000
6.8/11 M green
6.8/11 M yellow
6.8/11 M red
6.8/11 M purple
Item No.
Designation
Package contents
Description
00373313
Fastener guide
X 460F8
00373297
Piston
for single nails, lengths 1472 mm
X 460P8
for X-DNI, X-EDNI, X-ZF, X-FS and X-CR nails
00373299
Piston
X 460P8 AL
for X-AL-H nails
Online Product Tour

www.us.hilti.com/dx460tour
00373330
Buffer
X 460B
00373331
Washer holder
X 460WH23/36
for steel washers of 23 mm or 36 mm diameter
Pole Tool
00371661
Pole tool extension
your
Extenadch!
re
X-PT 460
www.us.hilti.com
6.17
R4DW-X High Speed Heavy-Duty

Pneumatic Fastening System
Technical Data
Dimensions (LxWxH)
17-3/4" x 4" x 20-1/4"
Weight
Handles Everything From Drywall Track to Hardwood Flooring
11.9 lb
Fastener range
5/8" to 2-1/2"
Magazine capacity
30 fasteners
Fastening rate
2 fasteners/second
Maximum operating pressure

175 psi
Air Consumption
0.23 ft3 /fastening
R e p a i r
Advantages
High fastening rate for greater productivity

Lightweight and compact for minimal operator fatigue
Powerful enough for wide range of applications
Ergonomic design for superior balance, operator
comfort
Durable construction for long service life, minimal
maintenance
P r o g r a m
MX nail collation for compatibility with Hilti DX

magazine tools
Large capacity magazine holds up to 30 fasteners for
fewer reloads
Backed by Hiltis nationwide network of sales/service
stations for on-site service
Narrow nose configuration available as option
Item No.
Description
00014921
R4DW-X Deluxe Drive Tool
Includes O-Ring Repair Kit, Deluxe Kit Box, Goggles, O-ring

Lubricant, Repair Tool Kit, Hilti Cleaning Cloth, Air Tool Oil
Accessories
Item No.
Description
00374783
AC2-PH11-30H (Honda Gas)
Horsepower
CFM
11
20.0 at 175 psi
Fasteners
Item No.
Description
Pin length
Qty
00298777
X-ZF14MX/M
1/2"
1000
00034436
X-ZF20MX/M
3/4"
1000
00034437
X-ZF27MX/M
1"
1000
00034438
X-ZF32MX/M
1-1/4"
1000
00034439
X-ZF37MX/M
1-1/2"
1000
00034440
X-ZF47MX/M
1-7/8"
1000
00034444
X-ZF52MX/M
2"
1000
00034452
X-ZF62MX/M
2-1/2"
1000
00034454
X-ZF72MX/M
2-7/8"
1000
00040386
SL 44-25 MX
1-3/4"
1000
00040291
SL 62-25 MX
2-1/2"
1000
00034541
X-EDNI 16 MX
5/8"
100
www.us.hilti.com
6.18

Technical Data
Dimensions (LxWxH)
17-3/4" x 2-3/4" x 6-5/8"
DX A41 I Fully Automatic Powder Actuated Tool

Install 3/8" Threaded Studs for Sprinkler Applications
Weight
9.2 lb with stop spall, 7.9 lb without
stop spall
Advantages:
Working principle
Fully automatic piston return

Integrated noise suppressor
10 booster safety tab" strips
contribute to increased operating
speed
Impact piston
Piston bore
10 mm
Booster
Hilti .27 caliber short collated strips of
10
Power Levels
Yellow (medium), Red (heavy), Purple
(ex heavy)
Fastener range
3/4" to 2-7/8"
R e p a i r
P r o g r a m
DX A41 I Program
Item No.
Description
00309769
DX A41-I
STD Basic tool with an X-AF10L baseplate and X-AP10L
piston pre-mounted
00311395
DX A41-I
DLX Basic tool with an X-SS10L spall stop and X-AP10L piston
pre-mounted
Pole Tool
X-PTA Modular Pole Tool for DX A40 / A 41 series tools
Item No.
Description
Length
00254682
X-PTA Modular Pole Tool Complete*
7 ft
Grip section
Includes grip section assembly (1.9 ft), receptacle assembly

(1.75 ft), 1 ft pipe section and 3 ft pipe section
* Note: All components can be ordered individually
Replacement Components
00254687
Grip section assembly
00254686
Receptacle assembly
00254685
1 ft pipe section (Optional)
00254684
3 ft pipe section
Receptacle
1.9 ft
1.75 ft
1 ft
3 ft
Pipe DXA 1 ft (Optional)
Pipe DXA 3 ft
X-PTA Modular Pole Tool

Advantages:
For Fastener Selection
see page:
6.20
Variable, modular length from 4' to 13'

Rugged, durable construction
Applicable to stand-up floor fastening
Easy Job-box storage
your
Extenadch!
re
www.us.hilti.com
6.19

Technical Data
Length
DX 600N Heavy-Duty Powder Actuated Tool

Ideal for Sprinkler Pipe Installation Using 3/8" Threaded Studs
14.5"
Weight
Advantages
Designed with the sprinkler

contractor in mind, the virtually
indestructible 10mm DX600N is
unequaled in consistent
performance and power for
demanding sprinkler installation
applications.
8.75 lb
The DX600 N is used in concrete

with strengths up to 8000 psi, and
tough aggregates such as river rock
and blue stone. It is also suitable
for structure steel up to grade 50.
Green (3)
Yellow (4)
Red (5)
Purple (6)
Working principle
co-acting piston
Piston bore
10 mm
Boosters
Hilti .27 caliber long in singles
Power Levels
Fastener range
3/4" to 4-5/8"
Drives 3/8" threaded studs, DS pins from 1" to

4-5/8" and EDS 3/4" or 7/8" pins for steel
Uses powerful .27 cal. long boosters for heavy duty

applications in concrete and steel
Stop spall reduces concrete spalling

R e p a i r
Low recoil when setting heavy duty fasteners in steel

or dense concrete
Pole tool accessory eliminates need for scaffolding
P r o g r a m

U.L. listed threaded studs for sprinkler pipe

installation in either concrete or steel
Item No.
Description
00006059
DX 600N Deluxe Kit

Deluxe kit supplied in impact resistant plastic Hilti case with
accessories (round wire brush 5/8", bore brush, flat wire
brush, ramrods, ramrod chain, spray lubricant), stop spall
stabilizer 6N/S4, guide 6N/F2 and piston 6N/DS,
safety goggles, selector chart and operating instructions
Grip Section
Pole Tool
00338757
Modular Pole Tool (for use with DX600N only)
00338758
Modular Pole Tool Receptacle (for use with DX600N only)
Fasteners
DS Heavy-Duty Pins
your
Extenadch!
re
Pipe DXA 3 ft
Receptacle
Shank diameter 0.177" for concrete and steel. Packaged in boxes of 100.
Item No.
Description
Length
00046157
00046158
00046159
00046160
00046161
00046162
00046164
00046165
00046166
00046167
00046168
DS 27 P10
DS 32 P10
DS 37 P10
DS 42 P10
DS 47 P10
DS 52 P10
DS 62 P10
DS 72 P10
DS 82 P10
DS 97 P10
DS 117 P10
1"
1-1/4"
1-1/2"
1-5/8"
1-7/8"
2"
2-1/2"
2-7/8"
3-1/4"
3-7/8"
4-5/8"
EDS Heavy-Duty Pins

Shank diameter 0.177" for steel. Packaged in boxes of 100.
Item No.
Description
Length
00046554
00046556
EDS 19 P10
EDS 22 P10
3/4"
7/8"
3/8"16 Studs
Shank diameter 0.205" for concrete. Packaged in boxes of 100.
Item No.
Description
Thread
Shank
00026472
00026473
00026476
00026569
W10-30-27 P10
W10-30-32 P10
W10-30-42 P10
EW10-30-18 P10 (steel)
1 1/4"
1 1/4"
1 1/4"
1 1/4"
1"
1-1/4"
1-5/8"
37/64"
3/8"-16 Studs Bulk Quantity

Combos include 1000 pins and boosters. Specify booster level with your order.
Item No.
Description
00299265
00299266
00299267
00299268
00299273*
00299274*
00299275*
00299276
W10-30-27/DXA Combo 1000 pc.

W10-30-32/DXA Combo 1000 pc.
W10-30-42/DXA Combo 1000 pc.
EW10-30--15/DXA (steel) Combo 1000 pc.
W10-30-27/DXA Coupler Combo 1000 pc.
EW-30-15 DXA (steel) Coupler Combo 1000 pc.
* Coupler combo includes 1000 pins, boosters and couplers.
www.us.hilti.com
6.20

Technical Data
Height
6-5/8 in.
Fully Automatic DX A40 Grating Tool

Hilti Makes Fastening Grating Discs Quicker - Saving Time and Money.
Power Adjustment Regulator

Yes
System Advantages
Automatic Tool
Fully automatic piston return

Optimal safety features and Hilti
DX safety principles.
Independent of any external
power source.
Low recoil for operator comfort.
Uses stainless steel threaded
studs and discs.
Yes
Working Principle
Impact
Approvals/Listings
Meets ANSI standard A10.3 and OSHA
requirements
Grating Disc Advantages

Provides flush surface and
minimized profile to help prevent
tripping.
Excellent for steel, fiberglass, and
aluminum grating.
Skid resistant surface.
Case Study #512502* Project Supervisor
ADDED
VALUE
$10,000 costs savings using Hilti

powder actuated system to fasten
grating instead of welding fasteners
and repainting the base steel.
DX Powder Actuated Fastening Tools

Item No.
Description
00312910 DX A40 Grating Tool, Complete

Supplied completely assembled for grating applications. Includes cleaning
brushes, spare parts pack, cleaning cloth, Hilti spray and operating instructions in
impact resistant plastic Hilti case
X-FCP checkerplate fastening disk

For a fastening height of 1/4" to 1/2"
Item No.
Description
00308859 X-FCP-F5/10
00308860 X-FCP-R5/10*
00308856 X-FCP sealing ring
Fastening height
Hot-dipped Stainless Package

galv.
steel
contents
1/4" to 1/2"
1/4" to 1/2"
200
200
200
X-FCP
* Special order. Allow 6 weeks for delivery.
X-FCM grating fastening disk

For a fastening height of 1" to 2"
Item No.
Description
Fastening height
00247181 X-FCM-R25/30
1" to 1-3/16"
00247182 X-FCM-R35/40
1-3/8" to 1-9/16"
00247183 X-FCM-R45/50
1-3/4" to 2"
00247184 X-FCM-R1 1/4"-1 1/2" 1-1/4" to 1-1/2"
00026582 X-FCM 25/30
1" to 1-3/16"
00026583 X-FCM 35/40
1-3/8" to 1-9/16"
00026584 X-FCM 45/50
1-3/4" to 2"
00247175 X-FCM 1 1/4"-1 1/2"
1-1/4" to 1-1/2"
00378683 X-FCM-25/30
1" to 1-3/16"
00378684 X-FCM-35/40
1-3/8" to 1-9/16"
00378685 X-FCM-45/50
1-3/4" to 2"
00378686 X-FCM-1 1/4"-1 1/2" 1-1/4" to 1-1/2"
X-CRM8 stainless steel threaded stud
Electrogalv.
Hot-dipped Stainless
galv.
steel
Package
contents
100
100
100
100
100
100
100
100
100
100
100
100
Sealing Ring
X-FCM
Shank diameter 5/32". Packages of 100.

Item No.
www.us.hilti.com
6.21
Description
Fastening height
For Disk
X-FCP-F
For Disk
X-FCP-R
X-FCM /
X-FCM-F Package
X-FCM-R Contents
00308857 X-CRM8-9-12 P8
1/4" to 21/64"
100
00255979 X-CRM8-15-12 P8
11/32" to 1/2"
Accessories
00306452 G40 conversion set (required to convert standard DX A40 to grating fastening tool)
X-CRM8-9-12P8
X-CRM8-15-12P8
Includes baseplate, piston, spare parts pack, 1" and 1-3/16" dia. centering device
and bit
DX 750 Grating System
Technical Data
Piston Bore
Up to 120 Grating Fastenings per Hour by a Single Operator
15 mm
Booster
.27 long magazine 10 booster strip
Fastener Types
ENP and HVB

Yes
Working Principle
Impact
Approvals/Listings
Meets ANSI standard A10.3 and OSHA
requirements
R e p a i r
P r o g r a m

System Advantages
Grating Disc Advantages
Optimal safety features and Hilti DX safety principles

Independent of any external power source
Uses stainless steel threaded studs and discs
Provides flush surface and minimized profile to help

prevent tripping
Excellent for steel, fiberglass, and aluminum grating
Skid resistant surface
DX Powder Actuated Fastening Tool

Item No.
Description
For Complete
Grating System Tool
Order Items:
00023252 DX 750 Deluxe
00023444 Baseplate Guide
Assembly
00023447 Piston 75-10/G
00023252 DX 750 Deluxe

Tool supplied in Hilti plastic case with accessories (ramrod,spare parts pack,
cleaning brushes, cleaning cloth, Hilti spray) and operating instructions
00023444 Baseplate Guide Assembly

00023447 Piston 75-10/G
00023246 Stop Ring Spare Pack
00006211 Ramrod (not shown)
00309218 Flat Bit For X-FCP (not shown)
X-FCP checkerplate fastening disk
For a fastening height of 1/4" to 1/2"

Item No.
Description
00308859 X-FCP-F5/10
00308860 X-FCP-R5/10*
00308856 X-FCP sealing ring
galv.
steel
Fastening height
1/4" to 1/2"
1/4" to 1/2"
Box
Qty
200
200
200
X-FCP
* Special order. Allow 6 weeks for delivery.
X-FCM grating fastening disk

For a fastening height of 1" to 2"
Item No.
Description
Fastening height
00247181 X-FCM-R25/30
1" to 1-3/16"
00247182 X-FCM-R35/40
1-3/8" to 1-9/16"
00247183 X-FCM-R45/50
1-3/4" to 2"
00247184 X-FCM-R1 1/4"-1 1/2" 1-1/4" to 1-1/2"
00026582 X-FCM 25/30
1" to 1-3/16"
00026583 X-FCM 35/40
1-3/8" to 1-9/16"
00026584 X-FCM 45/50
1-3/4" to 2"
00247175 X-FCM 1 1/4"-1 1/2"
1-1/4" to 1-1/2"
00378683 X-FCM-25/30
1" to 1-3/16"
00378684 X-FCM-35/40
1-3/8" to 1-9/16"
00378685 X-FCM-45/50
1-3/4" to 2"
00378686 X-FCM-1 1/4"-1 1/2" 1-1/4" to 1-1/2"
X-CRM8 stainless steel threaded stud
Electrogalv.
galv.
steel
Package
contents
100
100
100
100
100
100
100
100
100
100
100
100
Shank diameter 5/32". In packages of 100.

Item No.
Description
00308858 X-CRM8-9-12 P10

00247186 X-CRM8-15-12 P10
Fastening height
1/4" to 21/64"
11/32" to 1/2"
For Disk
X-FCP-F
For Disk
X-FCP-R
X-FCM /
X-FCM-F Package
X-FCM-R Contents
100
100
Sealing Ring
X-FCM
X-CRM8-9-12P8
X-CRM8-15-12P8
www.us.hilti.com
6.22

Technical Data
Piston Bore
10 mm
DX 460 SM Fastening System
NEW!
Fast Portable Tool for Reliable Decking Installation

Yes
Features & Benefits

The lightweight HiltiDX 460 SM
powder-actuated tool gives you
outstanding mobility and increased
comfort.
With integrated power regulation,
you can count on consistent,
accurate fastenings over a large
array of applications, with a driving
rate of up to 700 per hour.
DX 460 SM Deluxe Decking System

Item No.
Description
00371685 DX 460 SM Decking System

Supplied with impact-resistant plastic Hilti case, single fastener guide,
spare piston, cleaning set, spare buffer, ear protectors, safety glasses and
Hilti lubricant spray.
00370831 Stand Up Handle DX 460 SM DLX

Use the DX 460 SM as an upright decking system
Combo decking pins for DX 460 SM incl. 10-booster (.27 caliber short) strips
Diaphragm roof and floor deck applications
Item No.
Base steel thickness
Box Qty
00332770 X-EDNK 22 THQ12M HSN/DX 460 SM Combo 1/8" to 3/16"

00332769 X-EDN 19 THQ 12M HSN/DX 460 SM Combo 5/32" to 3/8"
Non-critical form deck applications
1000
1000
Item No.
Description
Description
00332771 X-ZF 22 THS 12M FDN/DX 460 SM Combo
Base steel thickness
Box Qty
1/8" to 1/4"
1000
X-EDNK22
X-EDN19
X-ZF22
Decking Pins Pallet Program
Pallet orders include toolbox complete with 2 pair of gloves, 4 pair of safety glasses and
deck markers.
Item No.
Description
Pallet Qty
00337703 X-EDN19 THQ 12M/ DX 460 SM Combo Pallet

00337704 X-EDNK22 THQ 12M/ DX 460 SM Combo Pallet
00337705 X-ZF22 THS12M/DX460 SM Combo Pallet
32,000
32,000
32,000
10-booster (.27 caliber short mag.) strips for DX 460 SM

Item No.
Description
00004842 Boosters 3/220MA red Bulk

00004843 Boosters 3/240MA purple Bulk
Power level
Color
Box Qty
Heavy
Extra Heavy
Red
Purple
1000
1000
Replacement Parts
Item No.
Description
00370827
00373303
00373330
00034122
00023924
Magazine X-SM
Piston X-AP PSM
Buffer (reinforced) X-460-B
Stand off gauge
Fingerless Leather Gloves (large size)
Shown at right
www.us.hilti.com
6.23
R4X12 Pneumatic Fastening System
Technical Data
Dimensions (LxWxH)
Excellent For Steel Decking Applications
17-3/4" x 20-1/4" x 4"
Weight
11.9 lb
Magazine capacity
20 fasteners
Fastening rate
2 fasteners/second
Maximum operating pressure

175 psi
Air consumption
0.23 ft3/fastening
R e p a i r
P r o g r a m

Advantages
High fastening rate for greater productivity

Lightweight and compact for minimal operator fatigue
Versatile enough for wide range of steel thicknesses (1/8" to 3/8")
Durable construction for long service life
High Shear Nails for fastening metal deck to bar joist in diaphragm applications
Form Deck Nails for attaching form deck to bar joist
Narrow nose configuration for F deck
R4X12 Pneumatic Decking System

Item No.
Description
00014939
R4X12 Deluxe Drive Tool
Includes O-Ring repair kit, deluxe Hilti steel case , safety goggles,
O-Ring lubricant, repair tool kit, Hilti cleaning cloth, air tool oil
Accessories
Item No.
Description
00374783
00014937
AC2-PH11-30H (Honda Gas)

Extension Handle for R4X12
Horsepower
CFM
11
20.0 at 175 psi
High Shear Fasteners

Item No.
Description
00034133
00034134
00332586
X-EDNK22 THQ12M High Shear Nail

X-EDN19 THQ12M High Shear Nail
X-ZF22 THS12M Form Deck Nail
Pin length
Quantity
7/8"
3/4"
7/8"
1,000
1,000
1,000
X-EDNK22
X-EDN19
X-ZF22
Pallet orders include toolbox complete with 2 pair of gloves, 4 pair of safety glasses and
deck markers.
Item no.
Description
Pallet Qty
00337700
00337701
00337702
X-EDN19 THQ12MX HSN Pallet

X-EDNK22 THQ12MX HSN - Pallet
X-ZF22 THS 12MX FDN - Pallet
32,000
32,000
32,000
www.us.hilti.com
6.24

Technical Data
Dimensions (LxWxH)
17-5/8" x 3-3/4" x 11-1/4"
DX 750 Decking System

The Portable Decking System for Structural Steel
Weight
9.8 lb with magazine
9.1 lb without magazine
Advantages
Working principle
Unique cycling feature reduces

operator effort, increases speed
and productivity
Power regulator broadens
application range: one tool for
thick or thin base materials
Magazined fasteners and
boosters mean increased
operating speed, fewer wasted
fasteners, easier handling in cold
weather
Shear connector
Impact piston
Piston bore
15 mm
Booster
Hilti .27 caliber long collated strips of
10
Power Levels
Green (light)
Yellow (medium)
Red (heavy)
Purple (ex heavy)
R e p a i r
P r o g r a m

DX 750 Decking System

Item No.
Description
00023252
00023274
DX 750 DLX (does NOT include MX75 Magazine)

DX 750 DLX with MX75 Magazine
Accessories
00023246
00023456
Stop Ring Spare 10-Pack

MX75 Magazine (for use with MX Fasteners)
Non Combo Fasteners (100/box)

Item No.
Description
Base Material
Base Steel Thickness
00046594
00077936
00040425
00040711
ENP2-21 L15
ENPH2-21 L15
ENP2K-20 L15
NPH2-42 L15*
Steel
Steel
Steel
Concrete
1/4" and greater

1/4" and greater
1/8" to 3/8"
Combo Fasteners (1000/box with cartridges)

Item No.
Description
Base Material
00040215
00040687
00040686
ENP2-21 L15
ENPH2-21 L15
ENP2K-20 L15
Steel
Steel
Steel
1/4" and greater

1/4" and greater
1/8" to 3/8"
Magazine Combo Fasteners (1000/box in rigid white strips of 10 for MX75

magazine) not for use in DX A70R ROOFIX
Item No.
Description
Base Material
Base
Steel Thickness
00040694
ENP2-21 L15MX
00040695
ENPH2-21 L15MX
00040696
ENP2K-20 L15MX
Steel
Steel
Steel
1/4" and greater

1/4" and greater
1/8" to 3/8"
Pallet orders include toolbox complete with 2 pair of gloves, 4 pair of safety glasses and deck markers.
Item no.
Description
Pallet Qty
00337706
00337707
ENP2-21 L15 MX Combo - Pallet

ENPH2-21 L15 MX Combo - Pallet
32,000
32,000
X-HVB Shear Connectors**

Item No.
Description
00023574
X-HVB 750 Conversion Set For use with X-HVB

shear connectors (not shown)
X-HVB 80
X-HVB 95
X-HVB 110
X-HVB 125
X-HVB 140
00239357
00239358
00239359
00239360
00239361
Qty
250
250
250
200
200
For higher steel strengths *NPH2 Fasteners are used for attaching metal decking to concrete
Requires baseplate 75/S3 (00023414) and piston 75/NPH (00023428) with the DX KWIK System.
** Shear connector. Requires conversion set X-HVB750 (item no. 00023574)
www.us.hilti.com
6.25

Technical Data
Dimensions (LxWxH)
DX A70 R (ROOFIX) Decking System

Fasten Profiled Metal Sheet Deck Quickly And Easily To Structural Steel
38" x 12-1/2" x 5"
Weight
26 lb
Advantages
Magazine Capacity
Fully automatic
Ergonomic design allows the
operator to remain in an upright
position while tool is in use
Provides speed and performance
in decking applicationup to
1200 fastenings per hour
Increases productivity
For use in fastening to structural
steel 1/4" thick and greater
40/40 (40 nails and 40 boosters)
Boosters
Red (5)
Purple (6)
collated strips of 40
Load fastening pins with ease while in upright position
DX A70 R (ROOFIX) Powder Actuated Fastening System

Item No.
Description
00311793
DX A70 R Tool, complete

Supplied in plastic carrying case with accessories (cleaning brushes, safety
goggles, spare parts pack, cleaning cloth, Hilti spray, spare piston and
operating instructions)
00275562
X-DX A70 R-M Magazine
40-Booster (.27 caliber long mag.) strips for DX A70 R

Item No.
Description
00258971
5/300M-40 red
00258972
5-370M-40 purple
Combo Decking Pins for DX A70 R
Power Level
Color
Box Qty
Heavy
Extra Heavy
Red
Purple
400
400
Includes 40-booster (.27 caliber long mag.) flexible gray strips

Item No.
Description
00315650
00315651
ENP2-21L15 MXR DX A70 R Combo 1/4" and greater

ENPH2-21L15 MXR DX A70 R Combo* 1/4" and greater
Box Qty
2000
2000
* High strength nail for higher steel grades
Pins (non-combo decking) for DX A70 R, DX 750

Item No.
Description
Box Qty
00258969
00258968
ENP2-21L15 MXR
ENPH2-21L15 MXR
1/4" and greater

1/4" and greater
1000
1000
Pallet orders include toolbox complete with 2 pair of gloves, 4 pair of safety glasses and deck
markers.
Item No.
Description
Box Qty
00337708
00337709
Spare Parts
ENP2-21 L15 MXR DX A70R Combo - Pallet

ENPH2-21 L15 MXR DX A70R Combo - Pallet
32,000
32,000
Item No.
Description
Shown at right
00023268
00023246
00034122
Piston 75/ENP2-L
Stop Ring Spare Pack (package of 10)
Stand off gauge
www.us.hilti.com
6.26
Turbine Pin Removal System

Technical Data
Length
Hilti Turbine Pin Removal System
NEW!
14.5"
Weight
7.75 lb
Operating principle
Co-acting
Piston bore
8mm & 12mm
Boosters
Hilti .27 caliber long singles
Power levels
Green (3)
Yellow (4)
Red (5)
Purple (6)
The Hilti Turbine Pin Removal

System can reduce the need for
milling. The Hilti system loosens
small and large diameter bucket
pins with reduced recoil and noise.
Advantages
Increase
Uses powerful .27 caliber long

boosters
Low recoil
Reduced noise
Utilizes efficient co-acting
operating principle
Operator Comfort
Productivity
Efficiency
System Includes
Item No.
Description
00377451
DX 600N Turbine Piston Removal System

Deluxe kit supplied in impact-resistant plastic
Hilti case with tool & accessories:
1 each DX 600N Turbine Tool

2 each 12mm 6N/F1 piston guides
12 each 12mm 6N/12 pistons(anvils)
2 each 8mm 6N/F3 piston guides
12 each 8mm 6N/DN1 pistons (anvils)
12 each DX 600N Stop Rings
1 each Ramrod
1 each Cleaning kit and spray lubricant
1 each Safety Glasses and operating instructions
12 each
Stop Rings
2 each
Piston Guides: 8mm, 12mm
12 each
Pistons: 8mm, 12mm
Replacement Parts
Item No.
Description
00377452
00377829
00006411
00006413
00006188
00006211
12mm diameter pistons (anvils)

8mm diameter pistons (anvils)
12mm 6N/F1 piston guide
8mm 6N/F3 piston guide
DX600N Stop Rings
Ramrod
Qty
12 pack
12 pack
12 per Pack
Boosters (charges)
www.us.hilti.com
6.27
Item No.
Description
00050315
00050316
00050317
00050506
booster 5/140 light (green)

booster 5/260 medium (yellow)
booster 5/300 heavy (red)
booster 5/370 extra heavy (purple)
Fully Automatic
DX A40 HM Marking
System
DX A40 CM Portable Cold

Marking System With
Polyurethane Head
Technical Data DX A40 HM

Tool With Marking Head
Dimensions (L x W x H)
16-3/16" x 2-3/4" x 6-5/8"
Weight
10.47 lb
Working principle
Impact piston
Piston bore
15 mm
Booster
.27 cal. short in strips of 10
Power Levels
Green (3)
Yellow (4)
Technical Data DX A40 CM

Tool With Marking Head
Dimensions (L x W x H)
16-9/16" x 2-3/4" x 6-5/8"
Weight
8.93 lb
Working principle
Impact piston
DX A40 HM Advantages
DX A40 CM Advantages
Piston bore
Ideal for use by steel mills, heavy industry and testing

agencies
Cost effectively fulfills ISO requirements
Quick and reliable
Completely portable
Booster (cartridge)
Urethane head reduces tool weight

For marking on cold metal materials and pipes
Independent of any external power source
Effective system for ISO 9000, quality control and
inventory identification processes
15 mm
.27 cal. short in strips of 10
Power levels
Green (3)
Yellow (4)
DX A40 HM Hot Marking

Item No.
Description
00311190
DX A40 with an X-A40/HM steel marking head

Supplied in impact resistant plastic carrying case with
accessories (spare parts pack,cleaning brushes, cleaning
cloth, Hilti spray), safety glasses and operating instructions.
DX A40 CM Cold Marking

Item No.
Description
00315924
DX A40 with X-A40/CM polyurethane marking head

Supplied in impact resistant carrying case with accessories
(spare parts pack, cleaning brushes, cleaning cloth, Hilti
spray), safety glasses and operating instructions.
00267900
Piston X-AP 15H
Marking Characters (marking head accepts 7 or 10 characters)

See Page 6.29
Boosters
Item No.
Description
Power level
Qty
00247447
00004838
Accessories
Boosters 3/110MA Green

Boosters 3/130MA Yellow
light
medium
100
100
Item No.
Description
For diameter (inches)
00007984
Centering device
3/4" to 1 3/8"
00007985
Centering device
1 3/8" to 2"
00007986
Centering device
2" to 3 1/8"
00007987
Centering device
3 1/8" to 5 1/2"
Centering devices for marking on curved surfaces
(only for polyurethane head)
Item No.
00268222
For diameter (mm)
20 to 35 mm
35 to 50 mm
50 to 80 mm
80 to 140 mm
Description
Axle-CML (required when using a centering device)
www.us.hilti.com
Marking Characters see
page:
6.29
6.28
Powder Actuated Marking System
Marking Characters
Letters
Nomenclature
LS =
Low stress to minimize fissure
cracking
S=
Sharp character face
8/10
8 = 8mm character block width for
7 characters per row
10 = 10 mm actual character
height
5.6/6
5.6 =5.6 mm block width for
10 characters per row (narrow)
6 = 6 mm actual character height
5.6/10
5.6 =5.6 mm block width for
10 characters per row (narrow)
10 = 10 mm actual character
height
Letter
S 8/10
LS 8/10
LS 5.6/6
S 5.6/10
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Spacer
Dash
Point
00007276
00007277
00007278
00007279
00007280
00007281
00007282
00007283
00007284
00007285
00007286
00007287
00007288
00007289
00007290
00007291
00007292
00007293
00007294
00007295
00007296
00007297
00007298
00007299
00007300
00007301
00007747
00007783
00007785
00312532
00312533
00312534
00312535
00312536
00312537
00312538
00312539
00312540
00312541
00312542
00312543
00312544
00312545
00312546
00312547
00312548
00312549
00312550
00312551
00312552
00312553
00312554
00312555
00312556
00312557
00008127
00008128
00008129
00008130
00008131
00008132
00008133
00008134
00008135
00008136
00008137
00008138
00008139
00008140
00008141
00008142
00008143
00008144
00008145
00008146
00008147
00008148
00008149
00008150
00008151
00008152
00007784
00007786
00008157
00008159
00007591
00007592
00007593
00007594
00007595
00007596
00007597
00007598
00007599
00007600
00007601
00007602
00007603
00007604
00007605
00007606
00007607
00007608
00007609
00007610
00007611
00007612
00007613
00007614
00007615
00007616
00007930
00007083
00006072
LTR Set*
00007744
00373523
00008115
00007622
Numbers
Number
www.us.hilti.com
Marking Tools see page:
6.28
6.29
0
1
2
3
4
5
6
7
8
9
Spacer
Dash
Point
NBR Set*
S 8/10
LS 8/10
LS 5.6/6
S 5.6/10
00007266
00007267
00007268
00007269
00007270
00007271
00007272
00007273
00007274
00007275
00007747
00007783
00007785
00007743
00312558
00312559
00312560
00312561
00312562
00312563
00312564
00312565
00312566
00312567
00008116
00008117
00008118
00008119
00008120
00008121
00008122
00008123
00008124
00008125
00007784
00007786
00373524
00008157
00008159
00008114
00007581
00007582
00007583
00007584
00007585
00007586
00007587
00007588
00007589
00007590
00007930
00007083
00006072
00007621
Plastic Case for 120 Characters
00007767
* Set includes two spacers along with letters and numbers.
Accessories
Accessories
Compressor Accessories
Item No.
Description
Thread Diameter
00210203
00210207
00012990
00210204
00014635
00095495
00210834
Regulator with Gauge (200psi)

Filter (200psi)
Filter Assembly G154 (Incl. filter element and metal housing)
Gauge (300psi)
Compressor Pump Oil (1 Qt)
Synthetic Blue Compressor Oil (1 Qt)
Auxiliary Air Tank (8 gal)
1/4" external
Shown Right
Not Shown
Not Shown
Item No.
Description
00014615
00014616
00012056
00014618
00014648*
00014632
00014633*
00014631*
Coupler Female 580-38

Coupler Male 581-38
Conn. Male 5801-38
Conn. Female 5802-38
Hose Barb B3838
38 NPT Brass Tee T38
Nipple NL 38-38
Bushing Hex 12-38
Pneumatic Fittings
Connection Size
Thread Diameter
3/8"
3/8"
3/8"
3/8"
3/8"
N/A
N/A
N/A
3/8" internal
3/8" external
3/8" external
3/8" internal
3/8"external
3/8" (3) internal
3/8"x 2" external
1/2" x 3/8" internal
Shown Right
*Limited stock
Lubricants & Accessories

Item No.
Description
Shown Right
00014637
00014599
00012423
Hoses
Air Tool Lubricant (1 Pint)

Kilfrost Lubricant (For cold weather operation of tools)
O-Ring Lube/Grease
Item No.
Description
00031517
00031516
Safety Glasses
Straight Hose with Fittings R38-100

Straight Hose with Fittings R38-50
Item No.
Description
00337051
00337050
Safety Glasses - Mirrored (UVEX)

Safety Glasses - Clear (UVEX)
Hose Diameter
Hose Length
Material
3/8"
3/8"
100'
50'
Rubber
Rubber
Shown Right
not shown
Shown Right
NEW
NEW
NEW!
www.us.hilti.com
6.30
Hilti Booster Selector Guide
Powder Actuated Fastening

Booster Selection
1 2 3 4 5 6
Commitment to Quality: Producing a high-quality booster means each component of the processdriving power,
firing sensitivity, propellant specification and magazine strength is correct.
Using Hilti powder actuated tools combined with Hilti boosters and fasteners produce the #1 powder actuated fastening
system in the industry! The resultsthe highest quality fastenings combined with safety, reliability and low maintenance.
Tool
DX E72/DXE37
DX 35
DX 350
DX 351
DX 36M
DX 450
DX A40 HM**
DX A40 CM**
Hilti Booster Type
Power Level
Color/Number
Hilti .22 Cal.
Gray/1
Brown/2
Green/3
Yellow/4
Green/3
Yellow/4
Red/5
Green/3
Yellow/4
Red/5
White/2****
Green/3
Yellow/4
Red/5
Purple/6*
White/2****
Green/3
Yellow/4
Red/5
Purple/6*
Hilti .25 Cal. in

strips of 10 each
Hilti .27 Cal. Short in

strips of 10 each
** Green/Yellow Only
DX A41****
**** Yellow/Red/
Purple Only
DX A41 I***
DX A41 SM
DX 460
DX 460 SM***
*** Red/5 & Purple/6 Only
DX 600N
DX 650
DX 750
DX 750 MX
DX 750G
DX 750H*
DX 750HM*
DX 750 I
Item No.
Box Qty
.22 Caliber
.22 Caliber
.22 Caliber
.22 Caliber
Booster 75M Light
Booster 120M Medium
Booster 150M Heavy
Booster 75M Light Bulk
Booster 120M Medium Bulk
Booster 150M Heavy Bulk
Booster 3/90MA Extra Light
Booster 3/110MA Light
Booster 3/130MA Medium
Booster 3/220MA Heavy
Booster 3/240MA Extra Heavy
Booster 3/90MA Extra Light Bulk
Booster 3/110MA Light Bulk
Booster 3/130MA Medium Bulk
Booster 3/220MA Heavy Bulk
Booster 3/240 Extra Heavy Bulk
00050395
00050396
00050397
00050398
00050106
00050107
00050108
00050115
00050116
00050117
00333318
00247447
00004838
00004839
00004840
00333317
00247446
00004841
00004842
00004843
100
100
100
100
100
100
100
1000
1000
1000
100
100
100
100
100
1000
1000
1000
1000
1000
Purple/6 for DX 450,

DX 451 & DX A41 I
**** For DX 351 only
Hilti .27 Cal. Long Single
Green/3
Yellow/4
Red/5
Purple/6
Booster 5/140 Light

Booster 5/260 Medium
Booster 5/300 Heavy
Booster 5/370 Extra Heavy
00050315
00050316
00050317
00050506
100
100
100
100
Hilti .27 Cal. Long in

strips of 10 each
Green/3
Yellow/4
Red/5
Purple/6
Green/3
Yellow/4
Red/5
Purple/6
Booster 5/140M Light

Booster 5/260M Medium
Booster 5/300M Heavy
Booster 5/370M Extra Heavy
Booster 5/140M Light Bulk
Booster 5/260M Medium Bulk
Booster 5/300M Heavy Bulk
Booster 5/370M Extra Heavy Bulk
00050318
00050320
00050322
00050605
00050323
00050324
00050326
00050614
100
100
100
100
1000
1000
1000
1000
Hilti .27 Cal. Long in

strips of 40 each
Red/5
Purple/6
5/300 M-40 Red

5/370 M-40 Purple
00258971
00258972
400
400
* Green/Yellow only
DX A70 R
Description
www.us.hilti.com
6.31
Modular Pole Tools
The Most Complete Line of

Modular Pole Tools In The Industry
Advantages
Completely modular
Eliminates need for ladders or
scaffolding
Adjustable 4' to 13'
Disassembles for easy storage
Applications
Acoustical ceilings
Drywall lathing
Overhead sprinklers
HVAC straps
Lighting
Extend your
reach!
ADDED
VALUE
Case Study #6397*
Project Manager

savings installing Hilti
X-EMCH clips from the
ground using Hilti
powder actuated tool
mounted on pole tool
versus drilling anchor
holes and installing
J-hooks while standing
on a ladder.
* For complete details, contact
Hilti. Actual results may vary.
DX 351: X-PT 351 Modular Pole Tool*

Includes grip section assembly (1.9 ft), receptacle assembly (1.75 ft), 1 ft pipe
section and 3 ft pipe section
Item No.
Description
00333310
X-PT351 Modular Pole Tool Complete*
Item No.
00254687
00333312
00254685
00254684
Description

Receptacle assembly
3 ft pipe section
Grip section
Length
7 ft
Length
1.9 ft
1.75 ft
1 ft
3 ft
Pipe DXA 3 ft
DX A40/A41 and DX 460: X-PTA Modular Pole Tool*

Grip section
Item No.
Description
Length
00371661
X-PTA 460 Modular Pole Tool Complete*
7 ft
00254682
X-PTA DX A40/41 Modular Pole Tool Complete* 7 ft
Item No.
Description
Length
00254687
00371663
00254686
00254685
00254684

Receptacle assemblyDX 460
Receptacle assemblyDX A40/41
3 ft pipe section
1.9 ft
1.75 ft
1.75 ft
1 ft
3 ft
Receptacle
Pipe DXA 3 ft
DX 35/350: X-PT 35 Pole Tool

Grip section
Item No.
Description
00309067
Pole X-PT 35/350 Pole Tool Complete*
00254687
00309508
ReceptacleDX 35/350
00254685
Pipe DXA 1 ft section (Optional)
00254684
Pipe DXA 3 ft section
Length
www.us.hilti.com
7 ft
1.9 ft
1.75 ft
1 ft
3 ft
Receptacle
Pipe DXA 3 ft

DX 351 see page 6.14
DX A41 see page 6.19
DX 460 see page 6.17
*All components can be ordered individually.
6.32
Accessories
Accessories
Wire Tying Fixture
Storage Cabinet
To attach suspension wire to ceilings clips.
Lockable, wall-mount cabinet measuring 34"H x 27"W x 6"D.
Item No.
Description
Item No.
Description
00052075
Wire Tying Fixture WTF II (drill not included)
00059903
00331543
Cabinet CH-36
Replacement Lock and Key Set
NEW!
Nuts, Washers, Couplers, etc.
Instruction Manuals*/Selector Charts
Item No.
Description
Item No.
Description
00069850
00069851
00058068
00051731
0037671
00051726
00051739
00051741
00376712
00058378
00058387
00058831
00058275
00058295
Nut-Wshr 1/4 for W6 studs

Nut-Wshr 3/8 for W10 studs
Washer R-18 5/8 Neoprene Backed
Washer R-23 7/8"
Washer R-23 7/8" - Bulk
Washer R-25S 1" w/ 1/4. 20 threads
Washer R-32 1 1/4"
Washer R-36 1 7/16
Washer R-36 1 7/16 - Bulk
Coupler 1/4-20
Coupler 3/8-16
Adapter B 1/4 x 3/8
Eye Coupling EC 1/4
Eye Coupling EC 3/8
00001082*
00002143*
00002726*
00003098*
00232346*
00089025*
00006084*
00006071*
00059049*
00254192*
00011951*
00014940*
00089026
00089808
00371665*
00332581*
DXE Instruction Manual

DX35 Instruction Manual
DX36M Instruction Manual
DXA40/41 Instruction Manual
DX600N Instruction Manual
DX650HM Instruction Manual
R4DW-X Instruction Manual
R4X12 Instruction Manual
DX451 Selector Chart
DX600N Selector Chart
DX 460 Instruction Manual
DX 351 Instruction Manual
*Manuals mailed direct to customer from Tulsa, OK
Cleaning Kits / Safety Glasses

Item No.
Description
00259271
DX Cleaning Kit
Includes 3 brushes, spray lubricant and cleaning cloth
www.us.hilti.com
6.33
00372810
00337260
00337051
00337050
DX 460 Cleaning Kit

DX 351 Cleaning Kit
Safety Glasses - Mirrored (UVEX)
Safety Glasses - Clear (UVEX)
Fastener Program
Indicates fastener/tool compatibility
X-CR Pins (Stainless Steel)

For applications in exposed and corrosive environments. Packaged in boxes of 100.
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
X-CR
Description
X-CR 14 P8
Shank" (mm)
0.145 (3.7)
Length" (mm)
1/2" (14)
100
00306701
DX 460
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.158 (4.0)
0.158 (4.0)
0.158 (4.0)
0.158 (4.0)
5/8" (16)
5/8" (18)
13/16" (21)
15/16" (24)
1-1/8" (29)
1-5/16" (34)
1-1/2" (39)
1-3/4" (44)
2-1/8" (54)
1-1/2" (39)
100
100
100
100
100
100
100
100
100
100
00247356
00247357
00247358
00247359
00247360
00247361
00247362
00247363
00247429
00247354
X-CR Pins with 1/2" stainless steel washer
X-CR 16 P8
X-CR 18 P8
X-CR 21 P8
X-CR 24 P8
X-CR 29 P8
X-CR 34 P8
X-CR 39 P8
X-CR 44 P8
X-CR 54 P8
X-CR 39 P8 S12
X-CR 44 P8 S12
0.158 (4.0)
1-3/4" (44)
100
00247355
X-AL Pins (High Strength)

For high strength psi concrete and heavy grade steel applications
Description
Shank" (mm)
Length" (mm)
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
X-AL With plastic 'top hat' washer
X-AL-H 12THP
0.146 (3.7)
5/16" (12)
100
00020082
X-AL With standard 8mm plastic washer
X-AL-H 14THP
X-AL-H 19THP
X-AL-H 22THP
X-AL-H 16 P8
0.146 (3.7)
0.158 (4.0)
0.158 (4.0)
0.146 (3.7)
1/2" (14)
3/4" (19)
7/8" (22)
5/8" (16)
100
100
100
100
00020083
00020084
00020085
00040876
0.158 (4.0)
0.158 (4.0)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
3/4" (19)
3/4" (19)
7/8" (22)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-5/8" (42)
1-7/8" (47)
2" (52)
2-1/4" (57)
2-1/2" (62)
2-7/8" (72)
1000
100
100
100
100
100
100
100
100
100
100
100
00034116
00040877
00040878
00040863
00040879
00040880
00040881
00040882
00040883
00040884
00040886
00232599
00232600
00232600
00232600
X-AL COMBO X-AL-H19THP Combo
X-AL-H 19 P8
X-AL-H 22 P8
X-AL-H 27 P8
X-AL-H 32 P8
X-AL-H 37 P8
X-AL-H 42 P8
X-AL-H 47 P8
X-AL-H 52 P8
X-AL-H 57 P8
X-AL-H 62 P8
X-AL-H 72 P8
0.158 (4.0)
X-AL-H22P8 Combo
X-AL-H27P8 Combo
X-AL-H32P8 Combo
X-AL-H37P8 Combo
X-AL-H47P8 Combo
X-AL-H52P8 Combo
X-AL-H62P8 Combo
0.158 (4.0)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
7/8" (22)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-7/8" (47)
2" (52)
2-1/2" (62)
1000
1000
1000
1000
1000
1000
1000
00232603
00232606
00232609
00254145
00232612
00232614
00232616
00232603
00232606
00232609
00254145
00232612
00232614
00232616
00232603
00232606
00232609
00254145
00232612
00232614
00232616
Combos include 1000 pins and boosters packaged separately.

Specify booster power level (color) with your order.
00232602
00232605
00232608
00232600
00232603
00232606
00232609
00254145
00232612
Case Study #51102* Project Planner/Engineer
X-EDNI Premium Ballistic Point Pins
ADDED
VALUE
$4,680 project labor savings fastening metal brackets to steel using Hilti powder
actuated systems with steel pins versus tek screw (self drilling screw) method. No
electric power source was required using Hilti Powder Actuated System.
For steel
Description
Shank" (mm)
X-EDNI single pins
X-EDNI 16 P8
0.145" (3.7 mm)
X-EDNI MX collated pins in strips of 10
X-EDNI 19 P8
X-EDNI 22 P8
X-EDNI 16 MX (collated)
(Tool with magazine required)
X-EDNI 19 MX (collated)
Length" (mm)
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
5/8" (16 mm)
100
00034536
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
3/4" (19)
7/8" (22)
5/8" (16)
100
100
100
00034537
00034538
00034541
0.145 (3.7)
3/4" (19)
100
00034542
Qty
100
Non-Combo Item No.

44159
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
1000
44164
00298507
00298900
00298436
00298436
00298436
00298436
00332580
00332580
DX 460
DAK Premium Pin

For steel fastening
DAK premium pins for steel fastening
Description
DAK 16P8
Shank" (mm)
0.145 (3.7)
DAK 16P8T
0.145 (3.7)
Combos include 1000 pins and boosters packaged separately. Specify booster power level (color) with your order.
DAK Combo
DAK 16P8T Combo
Length" (mm)
5/8 (16)
5/8 (16)
0.145 (3.7)
5/8 (16)
1000
DAK MX Combo pins in strips of 10 (Tool w/ magazine required) DAK 16 MX SP Combo 0.145 (3.7)
5/8 (16)
1000
00332580
6.34
Fastener Program
X-DNI Premium Ballistic Point Pins

For concrete and steel
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
X-DNI single pins
Description
X-DNI 19 P8
0.145" (3.7)
3/4" (19)
100
00034347
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
7/8" (22)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-1/2" (42)
1-7/8" (47)
2" (52)
2-1/4" (57)
2-1/2" (62)
2-7/8" (72)
3-1/4" (82)
3-3/4" (97)
4-1/2" (117)
1" (27)
100
100
100
100
100
100
100
100
100
100
100
100
100
100
00034351
00034352
00034353
00034354
00034355
00034357
00034360
00034361
00034363
00034364
00034365
00034368
00034548
00034388
X-DNI single pins with 15 mm diameter pre-mounted steel washer
X-DNI 22 P8
X-DNI 27 P8
X-DNI 32 P8
X-DNI 37 P8
X-DNI 42 P8
X-DNI 47 P8
X-DNI 52 P8
X-DNI 57 P8
X-DNI 62 P8
X-DNI 72 P8
X-DNI 82 P8
X-DNI 97 P8
X-DNI 117 P8
X-DNI 27 P8 S15
X-DNI single pins with 36 mm diameter pre-mounted steel washer
X-DNI 32 P8 S15
X-DNI 32 P8 S36
0.145" (3.7)
0.145" (3.7)
1-1/4" (32)
1-1/4" (32)
100
100
00034398
00034549
X-DNI 72 P8 S36
X-DNI 19 P8 Combo
0.145" (3.7)
0.145" (3.7)
2-7/8" (72)
3/4" (19)
500
1000
00034552
X-DNI Premium pin combo for concrete (non-collated)
00095624
00095623
00095623
00095623
00095623
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
7/8" (22)
1" (27)
1 1/4" (32)
1 1/2" (37)
1 5/8" (42)
1 7/8" (47)
2" (52)
2 1/4" (57)
2 1/2" (62)
2 7/8" (72)
5/8" (16)
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
00095626
00095628
00095636
00095638
00095625
00095627
00095629
00095637
00095639
00095640
X-DNI premium pin combo for steel (non-collated)
X-DNI 22 P8 Combo
X-DNI 27 P8 Combo
X-DNI 32 P8 Combo
X-DNI 37 P8 Combo
X-DNI 42 P8 Combo
X-DNI 47 P8 Combo
X-DNI 52 P8 Combo
X-DNI 57 P8 Combo
X-DNI 62 P8 Combo
X-DNI 72 P8 Combo
X-EDNI 16 P8 Combo
00095646
00095645
00095625
00095627
00095629
00095637
00095639
00095640
00095641
00095642
00095643
00095644
00095645
00095625
00095627
00095629
00095637
00095639
00095640
00095641
00095642
00095643
00095644
00095645
00095625
00095627
00095629
00095637
00095639
00095640
00095641
00095642
00095643
00095644
00095645
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
3/4" (19)
7/8" (22)
3/4" (19)
1000
1000
100
00095648
00095650
00095647
00095649
00095647
00095649
X-DNI MX collated pins in strips of 10
X-EDNI 19 P8 Combo
X-EDNI 22 P8 Combo
X-DNI 19 MX (collated)
00095647
00095649
00095647
00095649
X-DNI MX premium pin combo for concrete (pins collated in strips of 10) X-DNI 19 MX Combo
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
7/8" (22)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-1/2" (42)
1-7/8" (47)
2" (52)
2-1/2" (62)
2-7/8" (72)
3/4" (19)
100
100
100
100
100
100
100
100
100
1000
00247111

Combos include pins and boosters
packaged separately in boxes of 100 each.
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
7/8" (22)
1" (27)
1 1/4" (32)
1 1/2" (37)
1 5/8" (42)
1 7/8" (47)
2" (52)
2 1/2" (62)
2 7/8" (72)
5/8" (16)
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
00247112
00247113
00247114
00247112
00247113
00247114
00247115
00247116
00247117
00247118
00247119
X-EDNI MX premium pin combo for steel (pins collated in strips of 10)
X-DNI 22 MX Combo
X-DNI 27 MX Combo
X-DNI 32 MX Combo
X-DNI 37 MX Combo
X-DNI 42 MX Combo
X-DNI 47 MX Combo
X-DNI 52 MX Combo
X-DNI 62 MX Combo
X-DNI 72 MX Combo
X-EDNI 16 MX Combo
00247109
00247109
00247112
00247113
00247114
00247115
00247116
00247117
00247118
0024711
0009566
00247109
X-EDNI 19 MX Combo
0.145" (3.7)
1000
00247110
00247110
00247110

packaged separately in boxes of 100 each.
Shank" (mm) Length" (mm)
3/4" (19 )
00034370
00034372
00034377
00034378
00034379
00034380
00034382
00034384
00034386
00034545
00247111
www.us.hilti.com
6.35

Fastener Program
X-DW Premium Drywall Track Pins

For concrete and concrete block
Description
Shank" (mm)
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
X-DW COMBO
X-DW 20 THP Combo
0.118" (3.0 mm)
Length" (mm)
3/4" (20 mm) 1000
00338857
00338706
00337806
00337806
00337806
00337806

packaged separately. Specify booster
power level (color) with your order.
X-DW 20 THP MC Combo

X-DW 20 THP Pallet Combo
X-DW 27 THP Combo
X-DW 39 THP Combo
0.118" (3.0 mm)

0.118" (3.0 mm)
0.118" (3.0 mm)
0.118" (3.0 mm)
3/4" (20 mm) 4000

3/4" (20 mm)40000
1" (27 mm) 1000
1 5/8" (39 mm) 1000
00373664
00373663
00338858
00373666
00373665
00338707
00373666
00373665
00337807
00338461
00373666
00373665
00337807
00338461
00373666
00373665
00337807
00338461
00373666
00373665
00337807
00338461
Description
Shank" (mm)
DX 35
DX E72
DX 351
DX 350
DX 36M
X-DW MX COMBO collated in strips of 10
X-DW 20 MX Combo
0.118" (3.0 mm)
3/4" (20 mm) 1000
00337808
00337808

Combos include pins and boosters packaged separately.
Specify booster power level (color) with your order
X-DW 20 MX MC Combo
X-DW 20 MX Pallet Combo
X-DW 27 MX Combo
0.118" (3.0 mm)

0.118" (3.0 mm)
0.118" (3.0 mm)
3/4" (20 mm) 4000

3/4" (20 mm)40000
1" (27 mm) 1000
00373656
00373655
00337809
00373656
00373655
00337809
Length" (mm)
Qty
Qty
Non-Combo Item No.
Non-Combo Item No.
DX 460
ESD Premium Drywall Track Pins

For steel
Description
Shank" (mm)
ESD single pins
ESD 16 P8 TH
0.145" (3.7 mm)
Length" (mm)
5/8" (16 mm) 1000
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
00044171
ESD COMBO
ESD 16 P8T Combo
0.145" (3.7 mm)

ESD 16 P8T MC Combo

ESD 16 P8T Pallet Combo
0.145" (3.7 mm)

0.145" (3.7 mm)
DX 460
5/8" (16 mm) 1000
00040081
00040788
00040082
00040082
00040082
00040082
5/8" (16 mm) 6000

5/8" (16 mm)24000
00373670
00373669
00373668
00373667
00373668
00373667
00373668
00373667
00373668
00373667
www.us.hilti.com
6.36

Fastener Program
X-ZF Pins Standard Pins

For concrete and steel
Description
Shank
in. (mm)
Length
in. (mm)
Qty
Non-Combo
Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
X-ZF single pins
X-ZF 14 THP
0.145" (3.7)
9/16" (14)
1000
00034558
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.145" (3.7)
3/4" (20)
7/8" (22)
1" (27)
1-1/4" (32)
1-7/8" (47)
2-1/2" (62)
9/16" (14)
1000
1000
1000
1000
1000
1000
1000
00034559
00298794
00034408
00034411
00034415
00239186
00299603
X-ZF single pins COMBO
X-ZF 20 THP
X-ZF 22 P8 TH B
X-ZF 27 P8
X-ZF 32 P8
X-ZF 47 P8
X-ZF 62 P8
X-ZF 14 THP Combo
00299607
00299607
00299607
00299607
X-ZF 14 THP MC-Combo

X-ZF 14 THP Pallet
X-ZF 14 THP Pallet
X-ZF 20 THP Combo
X-ZF 20 THP MC-Combo
X-ZF 20 THP P-Combo
X-ZF 22 P8T Combo
X-ZF 22 P8T MC-Combo
X-ZF 22 P8T P-Combo
X-ZF 27 P8 Combo
X-ZF 32 P8 Combo
X-ZF 37 P8 Combo
X-ZF 42 P8 Combo
X-ZF 47 P8 Combo
X-ZF 52 P8 Combo
X-ZF 62 P8 Combo
X-ZF 62 P8 1/2 Pallet
X-ZF 62 P8 Pallet
X-ZF 27 P8 S23
X-ZF 37 P8 S23
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
9/16" (14)
9/16" (14)
9/16" (14)
3/4" (20)
3/4" (20)
3/4" (20)
7/8" (22)
7/8" (22)
7/8" (22)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-5/8" (42)
1-7/8" (47)
2-1/8" (52)
2-1/2" (62)
2-1/2" (62)
2-1/2" (62)
1" (27)
1-1/2" (37)
6000
20000
24000
1000
4000
40000
1000
4000
20000
1000
1000
1000
1000
1000
1000
1000
5000
10000
1000
00373658
00373658
00373658
00373658
00299608
00299615
00373660
00299616
00299621
00095401
00095372
00299624
00299632
00299640
00299649
00299654
00299608
00299615
00373660
00299616
00299621
00095401
00095372
00299624
00299632
00299640
00299649
00299654
00299659
00239245
00299668
00299669
00299608
00299615
00373660
00299616
00299621
00095401
00095372
00299624
00299632
00299640
00299649
00299654
00299659
00239245
00299668
00299669
X-ZF single pins with 23 mm pre-mounted steel washer Combo X-ZF 27 P8 S23 Combo
0.138" (3.5)
1" (27)

X-ZF 32 P8 S23 Combo

X-ZF 37 P8 S36
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
1-1/4" (32)
1-1/2" (37)
1-5/8" (42)
1-7/8" (47)
1-1/4" (37)
X-ZF 62 P8 S36
X-ZF 72 P8 S36
X-ZF single pins with 36 mm pre-mounted steel washer Combo X-ZF 37 P8 S36 Combo
0.138" (3.5)
0.145" (3.7)
0.138" (3.5)
2-1/2" (62)
2-7/8" (72)
1-1/2" (37)
500
100
1000


X-ZF 72 P8 S36 1/2 P-Combo
X-ZF 72 P8 S36 P-Combo
X-ZF 14 MX (collated)
0.138" (3.5)
0.138" (3.5)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
2-1/8" (52)
2-1/2" (62)
2-7/8" (72)
2-7/8" (72)
2-7/8" (72)
9/16" (14)
1000
1000
1000
5000
10000
1000
X-ZF 14 MX Combo
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.145" (3.7)
0.145" (3.7)
3/4" (20)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-7/8" (47)
2-1/2" (62)
2-7/8" (72)
9/16" (14)
1000
1000
1000
1000
1000
1000
1000
1000
X-ZF 14 MX MC-Combo
X-ZF 14 MX Pallet
X-ZF 20 MX Combo
X-ZF 20 MX MC-Combo
X-ZF 20 MX Pallet
X-ZF 27 MX Combo
X-ZF 32 MX Combo
X-ZF 37 MX Combo
X-ZF 47 MX Combo
X-ZF 52 MX Combo
X-ZF 62 MX Combo
X-ZF 72 MX Combo
0.145" (3.7)
0.145" (3.7)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
0.145" (3.7)
9/16" (14)
9/16" (14)
3/4" (20)
3/4" (20)
3/4" (20)
1" (27)
1-1/4" (32)
1-1/2" (37)
1-7/8" (47)
2-1/8" (52)
2-1/2" (62)
2-7/8" (72)
4000
20000
1000
4000
40000
1000
1000
1000
1000
1000
1000
1000

X-ZF single pins with 23 mm pre-mounted steel washer
X-ZF single pins with 36 mm pre-mounted steel washer
X-ZF MX collated in strips of 10

X-ZF MX collated in strips of 10 Combo

Combos include pins and boosters packaged separately
www.us.hilti.com
6.37
00299605
00373657
00299604
00299606
00299613
00373654
00299614
00299620
00373675
00373674
00299623
00299631
00299639
00034457
00299608
00299615
00373660
00299616
00299621
00095401
00095372
00299624
00299632
00299640
00299649
00299654
00299659
00239245
00299668
00299669
1000
00299627
00299627
00299629
00299629
00299629
00299629
1000
1000
1000
1000
500
00299635
00299642
00299651
00299656
00299635
00299642
00299651
00299656
00299637
00299646
00299652
00299657
00299637
00299646
00299652
00299657
00299637
00299646
00299652
00299657
00299637
00299646
00299652
00299657
00299643
00299643
00299647
00299647
00299647
00299647
00299662
00299667
00299671
00299672
00299673
00299662
00299667
00299671
00299672
00299673
00299662
0029966
00299671
00299672
00299673
00034455
1000
00034473
00034480
00239187
00299611
00095186
00299612
00299619
00299622
00299630
00299638
00299648
00299653
00299658
00239244
00299661
00299666
00299670
00299674
00298777
00034436
00034437
00034438
00034439
00034440
00034452
00034454
00299610
00299610
00373671
00239526
00299618
00373672
00239257
00299626
00299634
MC = Master Carton
00373671
00239526
00299618
00373672
00239257
00299626
00299634
00299641
00299655
00299660
00299665
00251695
P=Pallet

Fastener Program
X-CF Economy Pins

For low strength / green concrete & temporary applications
Description
Shank
" (mm)
Length
" (mm)
Qty
Non-Combo
Item No.
00034492
X-CF single pins
X-CF 62 P8
0.138" (3.5)
2-1/2" (62)
1000
X-CF single pins Combo
X-CF62P8 Combo
0.138" (3.5)
2-1/2" (62)
2000

X-CF pin with 23mm steel washer combo
X-CF72P8S23 Combo
0.145" (3.7)
2-7/8" (72)
2000
Shank
" (mm)
Length
" (mm)
Qty
DX 35
DX E72
DX 351
00298639
DX 350
DX 36M
DX 460
00298636
00298636
00298636
00298638
00298638
00298638
SL Special Removable Forming Nails

For fastening 2x4, 2x6 etc. to concrete
Description
SL single pins Combo
SL44 DP8 Combo
0.145" (3.7)
1-3/4"(44)
1000

SL62 DP8 Combo
0.145" (3.7)
2-1/2" (62)
1000
Non-Combo
Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
00041307
00041307
00041307
00041307
00040641
00040641
00040641
00253663
Case Study #501408* Site Foreman
ADDED
VALUE
$4,200 project labor savings using Hilti

SL-MX breakaway fasteners versus using
standard powder actuated pins that must be
removed when job is complete.
Description
Shank
" (mm)
Length
" (mm)
Qty
Non-Combo
Item No.
DX 36M
DX 460
SL MX collated pins in strips of 10 Combo
SL 44-25 MX Combo
0.145" (3.7)
1-3/4"(44)
1000
00040409
00040409

SL 62-25 MX Combo
0.145" (3.7)
2-1/2" (62)
1000
00040406
00040406
Shank
" (mm)
Length
" (mm)
Qty
Non-Combo
Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
0.145" (3.7)
1"(28)
100
00040500
Non-Combo
Item No.
DX 35
Description
X-RE special removable fastener
X-RE 28P8
DX 35
DX E72
DX 351
DX 350
BC Rebar basket clips

Clips with pre-mounted pins for fastening rebar baskets during concrete highway / slab construction
Description
Shank
" (mm)
Length
" (mm)
Qty
DX E72
DX 351
DX 350
DX 36M
DX 460
BC
BC-ZF22 P8T Combo
0.138" (3.5)
7/8" (22)
1000
00299581
00299582
00299582
00299582
00299582

BC-ZF37 P8T Combo

BC-ZF47 P8T Combo
BC-ZF62 P8T Combo
0.138" (3.5)
0.138" (3.5)
0.138" (3.5)
1-1/2" (37)
1-7/8" (47)
2-1/2" (62)
1000
1000
1000
00299585
00299589
00299593
00299586
00299590
00299594
00299586
00299590
00299594
00299586
00299590
00299594
00299586
00299590
00299594
www.us.hilti.com
6.38
Fastener Program
X-IE Insulation Fasteners

For fastening EPS / EIFS insulating materials to concrete
Description
Insulating
Material Thickness
Qty
Non-Combo
Item No.
1" (25)
300
00376463
00376465
00373466
00367467
00367468
00367469
00367470
00367471
00367472
00367474
00367475
00299712
00299712
00299714
00299715
00299716
00299717
00299718
00299719
00299720
00299721
00299714
00299715
00299716
00299717
00299718
00299719
00299720
00299721
X-IE
X-IE 6-25 PH 37
(Special equipment and pistons required)
X-IE 6-35 PH 47
X-IE 6-40 PH 52
X-IE 6-45 PH 52
X-IE 6-50 PH 52
X-IE 6-60 PH 52
X-IE 6-70 PH 52
X-IE 6-75 PH 52
X-IE 6-80 PH 52
X-IE 6-100 PH 52
X-IE 6-120 PH 72
X-IE 6-25 PH 37 Combo
1-1/2" (35)
1-5/8" (40)
1-3/4" (45)
2" (50)
2-1/2" (60)
2-3/4" (70)
3" (75)
3-1/4" (80)
4" (100)
4-3/4" (120)
1" (25)
300
300
300
300
300
200
200
200
200
150
300

1-5/8" (40)
1-3/4" (45)
2" (50)
2-1/2" (60)
2-3/4" (70)
3" (75)
3-1/4" (80)
4" (100)
300
300
300
300
200
200
200
200
X-IE COMBO
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
X-SW Soft Washer Pins with large pre-mounted soft plastic washers
For fastening insulation and membranes / plastic sheeting to concrete
Description
Washer
Diameter
Length
" (mm)
Qty
Non-Combo
Item No.
Washers only (without pins)
X-SW30 Soft Washer
30 mm
no pin
500
00244724
Pins pre-mounted with washers
X-SW30 Soft Washer Bulk

X-SW60 Soft Washer
X-SW60 Soft Washer Bulk
X-SW 30 ZF37
30 mm
60 mm
60 mm
30 mm
no pin
no pin
no pin
1-1/2" (37)
7000
500
2100
150
00040701
00244725
00040702
00040643
30 mm
30 mm
60 mm
60 mm
60 mm
30 mm
1-1/2" (37)
2-1/2" (62)
1-1/2" (37)
1-7/8" (47)
2-1/2" (62)
1-1/2" (37)
500
100
100
100
100
1000
00040614
00040645
00040617
00040618
00040619
X-SW COMBO (pins & boosters)
X-SW 30 ZF37
X-SW 30 ZF62
X-SW 60 ZF37
X-SW 60 ZF47
X-SW 60 ZF62
X-SW 30 ZF37 Combo (Gray)
X-SW 30 ZF37 Combo (White)
30 mm
30 mm
60 mm
60 mm
60 mm
2-1/2" (62)
1-1/2" (37)
1-1/2" (37)
1-7/8" (47)
2-1/2" (62)
1000
1000
1000
1000
1000
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
00299386
00299385
00299387
00299387
00299387
00299387
00299394
00299410
00299398
00299402
00299406
00299393
00299409
00299397
00299401
00299405
00299395
00299411
00299399
00299403
00299407
00299395
00299411
00299399
00299403
00299407
00299395
00299411
00299399
00299403
00299407
00299395
00299411
00299399
00299403
00299407
www.us.hilti.com
6.39

Fastener Program
CC Ceiling Clips
For suspending ceiling grids and electrical services. Available with or without pre-tied wires.
All items marked combo include pins and boosters packaged separately. Specify booster power level (color) with your order.
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
Clip only pre-mounted with high performance pins
CC27XALH-22P8T
Description
7/8" (22)
0.158" (4.0)
100
00299814
Clip only pre-mounted with standard pins
CC27XALH-22P8T Combo
CC27XALH-27P8T
CC27XALH-27P8T Combo
CC27 ZF 27 P8T
7/8" (22)
1" (27)
1" (27)
1" (27)
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100
00299817
00299848
00299816
00299847
00299818
00299849
00299818
00299849
00299818
00299849
00299818
00299849
1" (27)
1" (27)
1-1/4" (32)
1-1/4" (32)
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
10000
100
1000
00299436
00299544
00299787
00299535
00299543
00299786
00299437
00299545
00299788
00299437
00299545
00299788
00299437
00299545
00299788
00299437
00299545
00299788
CC27 ZF 27 P8T Combo

CC27 ZF 27 P8T Pallet Combo
CC27 ZF 32 P8T
CC27 ZF 32 P8T Combo
4' Wire
Clip and pre-tied 12 Ga. 4' wire pre-mounted with high performance pins CC27XALH-22P8T 4'PT
Clip and pre-tied 12 Ga. 4' wire pre-mounted with standard pins
0.158" (4.0)
100
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100
CC27 ZF 27 P8T 4'PT Combo

CC27 ZF 32 P8T 4'PT
1" (27)
1-1/4" (32)
1-1/4" (32)
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
100
1000
00310228
00299819
00299823
00299850
00310223
7/8"
0.158" (4.0)
100
CC27XALH-22P8T 6'PT Combo

CC27XALH-27P8T 6'PT
CC27 ZF 27 P8T 6'PT
7/8" (22)
1" (27)
1" (27)
1" (27)
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100

CC27 ZF 32 P8T 6'PT
1" (27)
1-1/4" (32)
1-1/4" (32)
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
100
1000
00310229
00299827
00299854
00310224
7/8" (22)
0.158" (4.0)
100

CC27XALH-27P8T 8'PT
CC27 ZF 27 P8T 8'PT
7/8" (22)
1" (27)
1" (27)
1" (27)
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100

CC27 ZF 32 P8T 8'PT
1" (27)
1-1/4" (32)
1-1/4" (32)
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
100
1000
00310230
7/8" (22)
0.158" (4.0)
100
00299831
7/8" (22)
1" (27)
1" (27)
1" (27)
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
100
1000
00310231
00299835

CC27XALH-27P8T 10'PT
CC27 ZF 27 P8T 10'PT

1" (27)
1-1/4" (32)
CC27 ZF 32 P8T 10'PT Combo 1-1/4" (32)
12' Wire
00310325
7/8" (22)
1" (27)
1" (27)
1" (27)
10' Wire
Clip and pre-tied 12 Ga.10' wire pre-mounted with high performance pins CC27XALH-22P8T 10'PT
Clip and pre-tied 12 Ga.10' wire pre-mounted with standard pins
00310322
7/8" (22)
8' Wire
00299845

CC27XALH-27P8T 4'PT
CC27 ZF 27 P8T 4'PT
6' Wire
Pin Length Shank" (mm)

CC27XALH-27P8T 12'PT
00299858
00310225
00299862
00310226
7/8" (22)
0.158" (4.0)
100
7/8" (22)
1" (27)
1" (27)
1" (27)
0.158" (4.0)
0.177" (4.5)
0.177" (4.5)
0.138" (3.7)
1000
100
1000
100
0.138" (3.7)
0.138" (3.7)
0.138" (3.7)
1000
100
1000
Pin Length
Clip only
7/8"
7/8"
100
1000
00299551

1" (27)
1-1/4" (32)
CC27 ZF 32 P8T 12'PT Combo 1-1/4" (32)
DX 460
00299821
00299852
00299820
00299851
00299822
00299853
00299822
00299853
00299822
00299853
00299822
00299853
00299521
00299794
00299520
00299789
00299522
00299799
00299522
00299799
00299522
00299799
00299522
00299799
00299825
00299856
00299824
00299855
00299826
00299857
00299826
00299857
00299826
00299857
00299826
00299857
00299526
00299795
00299525
00299790
00299527
00299800
00299527
00299800
00299527
00299800
00299527
00299800
00299829
00299860
00299828
00299859
00299830
00299861
00299830
00299861
00299830
00299861
00299830
00299861
00299531
00299796
00299530
00299791
00299532
00299801
00299532
00299801
00299532
00299801
00299532
00299801
00299833
00299864
00299832
00299863
00299834
00299865
00299834
00299865
00299834
00299865
00299834
00299865
00299536
00299797
00299535
00299792
00299537
00299802
00299537
00299802
00299537
00299802
00299537
00299802
00299837
00299868
00299836
00299867
00299838
00299869
00299838
00299869
00299838
00299869
00299838
00299869
00310232
00299541
00299798
00299540
00299793
00299542
00299803
00299542
00299803
00299542
00299803
00299542
00299803
Qty
Non-Combo Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
100
00053461
00299553
00299552
00299554
00299554
00299554
00299554
00299866
00310227
CTV Clips
For fastening 1/4" TV or communication cable
Description
CTV
Cable Clip CTV 1/4"

CTV ZF22 P8T 1/4"

CTV ZF22 P8T 1/4" Combo
6.40
Fastener Program
X-ECH Plenum Rated Cable Hangers

For telecom/data and premise wiring applications
Description
Max # of
1/4" cables
Size
Qty
Non-Combo
Item No.
DX 35
DX E72
DX 351E
Hanger with pre-mounted pins
X-ECH-F/R-S DNI H42P8
1522
small
100
00373258
(Special equipment required)
X-ECH-F/R-M DNI H42P8

X-ECH-F/R-L DNI H42P8
ECH-F/R-S
3037
4552
1522
medium
large
small
100
50
100
00373259
00373260
00266694
ECH-F/R-M
ECH-F/R-L
3037
4552
medium
large
100
50
00266695
00266696
Hanger only - for use with drilled anchors
DX 350
DX 36M
DX 460
X-JH Cable Hangers

For fasteniing to concrete or steel
Description
Hanger Size
Shank
" (mm)
Shank
Length
" (mm)
Qty
NonCombo
Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
Ceiling mount J-Hook with pre-mounted premuim pins for concrete
X-JH/C-S DNI 27
Small 3/4"
0.145" (3.7)
1" (27)
50
03711013
Wall mount J-Hook with pre-mounted premium pins for concrete
X-JH/C-M DNI 27
X-JH/C-L DNI 27
X-JH/W-S DNI 27
Medium 1 5/16"
Large 2"
Small 3/4"
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
1" (27)
1" (27)
1" (27)
50
50
50
03711014
03711015
03711017
X-JH/W-M DNI 27
X-JH/W-L DNI 27
Ceiling mount J-Hook with pre-mounted high performance pins for concrete X-JH/C-S AL-H-22
Medium 1 5/16"
Large 2"
Small 3/4"
0.145" (3.7)
0.145" (3.7)
0.158" (4.0)
1" (27)
1" (27)
7/8" (22)
50
50
50
03711018
03711019
03711021
Wall mount J-Hook with pre-mounted high performance pins for concrete
X-JH/C-M AL-H-22
X-JH/C-L AL-H-22
X-JH/W-S AL-H-22
Medium 1 5/16"
Large 2"
Small 3/4"
0.158" (4.0)
0.158" (4.0)
0.158" (4.0)
7/8" (22)
7/8" (22)
7/8" (22)
50
50
50
03711022
03711023
03711025
Ceiling mount J-Hook with pre-mounted premium pins for steel
X-JH/W-M AL-H-22
X-JH/W-L AL-H-22
X-JH/C-S EDNI 16
Medium 1 5/16"
Large 2"
Small 3/4"
0.158" (4.0)
0.158" (4.0)
0.145" (3.7)
7/8" (22)
7/8" (22)
5/8" (16)
50
50
50
03711026
03711027
03711029
Medium 1 5/16"
Large 2"
Small 3/4"
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
5/8" (16)
5/8" (16)
1" (27)
50
50
500
03711030
03711031
95823
Ceiling mount J-Hook with pre-mounted premuim pins for concrete
X-JH/C-M EDNI 16
X-JH/C-L EDNI 16
X-JH/C-S DNI 27 P8TH Combo
95699
95699
95699
95699
Combos include J-Hook assembly and booster packaged separately.

Wall mount J-Hook with pre-mounted premium pins for concrete
X-JH/C-M DNI 27 P8TH Combo

X-JH/C-L DNI 27 P8TH Combo
X-JH/W-S DNI 27 P8TH Combo
Medium 1 5/16"
Large 2"
Small 3/4"
0.145" (3.7)
0.145" (3.7)
0.145" (3.7)
1" (27)
1" (27)
1" (27)
500
500
500
95824
95824
95826
95814
95815
95816
95814
95815
95816
95814
95815
95816
95814
95815
95816
X-JH/W-M DNI 27 P8TH Combo Medium 1 5/16"

X-JH/W-L DNI 27 P8TH Combo
Large 2"
Ceiling mount J-Hook with pre-mounted high performance pins for concrete X-JH/C-S ALH-22P8TH Combo
Small 3/4"
0.145" (3.7)
0.145" (3.7)
0.158" (4.0)
1" (27)
1" (27)
7/8" (22)
500
500
500
95827
95828
95817
95818
95882
95817
95818
95882
95817
95818
95882
95817
95818
95882
0.158" (4.0)
0.158" (4.0)
7/8" (22)
7/8" (22)
500
500
95883
95884
95883
95884
95883
95884
95883
95884
X-JH/C-M ALH-22P8TH Combo

X-JH/C-L ALH-22P8TH Combo
Medium 1 5/16"
Large 2"
www.us.hilti.com
6.41
Fastener Program
X-HS Hanger Brackets

For suspension of 1/4" and 3/8" threaded rod from concrete or steel.
1/4"
Description
Thread Size
Qty
Non-Combo Item No.
DX 35
DX 351
DX 350
Fastening to concrete
Fastening to steel
Stainless steel pin and bracket
Combo (includes boosters)
3/8"
X-HS W6 DNI-32P8S15
X-HS W6 EDNI-19P8 S15
X-HSR W6 CR 29 P8
X-HS W6 DNI-32P8 Combo
Pin Length
1-1/4"
3/4"
1-1/8"
1-1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
1000
00335425
00335435
00255915
00253751
DX E72
00253749 00253753
DX A40
00253753
00253753
DX 36M
00253753 00253753
DX 460
Fastening to concrete
Fastening to steel
Fastening to high strength concrete
Stainless steel pin and bracket
Combo (includes boosters)
X-HS W10 DNI-32P8S15

X-HS W10 EDNI 19 P8 S15
X-HS W10 AL-H 27 P8S15
X-HSR W10 CR 29 P8
X-HS W10 DNI-32P8 Combo
1-1/4"
3/4"
1"
1-1/8"
1-1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
100
100
100
100
1000
00335426
00335430
00335434
00255916
00336929
00336928 00336930
00336930
00336930
00336930 00336930
X-RH Rod Hangers

For suspension applications using smooth rod
Description
Rod
Diameter
Thread
Length
" (mm)
Shank
Length
" (mm)
Qty
Non-Combo
Item No.
DX 35
DX E72
DX A40
DX 351
DX 350
DX 36M
DX 460
Ceiling mount rod hanger with pre-mounted premuim pins for concrete
X-RH1/4-C-DN127
1/4"
0.145" (3.7)
1" (27)
50
0371037
Wall mount rod hanger with pre-mounted premium pins for concrete
X-RH1/4-W-DN127
1/4"
0.145" (3.7)
1" (27)
50
0371039
X-RH1/4-W AL-H-22
1/4"
0.158" (4.0)
7/8" (22)
50
0371043
Ceiling mount rod hanger with pre-mounted premuim pins for concrete
X-RH1/4-C-DN127 Combo
1/4"
0.145" (3.7)
1" (27)
1000
95829
95819
95819
95819
95819
95819
Combos include J-Hook assembly and booster packaged separately.

Wall mount rod hanger with pre-mounted premium pins for concrete
X-RH1/4-W-DN127 Combo
1/4"
0.145" (3.7)
1" (27)
1000
95831
95821
95821
95821
95821
95821
Ceiling mount rod hanger with pre-mounted high performance pins for concrete
X-RH1/4-C-ALH-22 Combo
1/4"
0.158" (4.0)
7/8" (22)
1000
95885
95885
95885
95885
95885
Ceiling mount rod hanger with pre-mounted high performance pins for concrete
Wall mount rod hanger with pre-mounted high performance pins for concrete
Ceiling mount rod hanger with pre-mounted premium pins for steel
www.us.hilti.com
6.42
Fastener Program
Concrete
Steel
EMTC Conduit Clips

Conduit
Size
Pin
Length
Qty
Non-Combo
Item No.
X-EMTC Conduit Clip 3/8"
3/8"
no pin
100
00335116
Clips with pre-mounted standard ZF pins

X-EMTC Conduit Clip 1"
X-EMTC ZF22 P8TH 3/8"
1/2"
3/4"
1"
3/8"
no pin
no pin
no pin
7/8"
100
100
100
100
00335117
00335118
00335119
00335120
1/2"
3/4"
1"
3/8"
1/2"
3/4"
1"
3/8"
7/8"
7/8"
7/8"
1"
1"
1"
1"
1"
100
100
100
100
100
100
100
1000
00338761
00338762
00338763
00335121
00335122
00335123
00335124
Clips with pre-mounted standard ZF pins

X-EMTC ZF22 P8TH 1"
X-EMTC ZF27 P8TH 1"
X-EMTC ZF27 P8TH 3/8" Combo
Premium clip no pins

X-EMTC ZF27 P8TH 1" Combo
EMTC Conduit Clip 1/2"
1/2"
3/4"
1"
1/2"
1"
1"
1"
no pin
1000
1000
1000
100
00053463
Premium clip with pre-mounted premium DNI pins
EMTC Conduit Clip 3/4"

EMTC Conduit Clip 1"
EMTC DNI22P8T 3/8"
3/4"
1"
3/8"
no pin
no pin
7/8"
100
100
100
00053464
00053465
00053249
1/2"
3/4"
1"
1/2"
1"
1"
1"
1"
100
100
100
1000
00299555
00299559
00299563
Premium clip with pre-mounted premium DNI pins
EMTC DNI27P8T 1/2"

EMTC DNI27P8T 3/4"
EMTC DNI27P8T 1"
EMTC DNI27P8T 1/2" Combo

EMTC DNI27P8T 3/4" Combo

EMTC DNI27P8T 1" Combo
3/4"
1"
1"
1"
1000
1000
Standard/premium grade
Description
Standard clip only no pins

DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
00335126
00335125
00335127
00335127
00335127
00335127
00335129
00335132
00335135
00335128
00335131
00335134
00335130
00335133
00335136
00335130
00335133
00335136
00335130
00335133
00335136
00335130
00335133
00335136
00299557
00299556
00299558
00299558
00299558
00299558
00299561
00299565
00299560
00299564
00299562
00299566
00299562
00299566
00299562
00299566
00299562
00299566
1/4" Threaded studs

For fastening to concrete and steel
Description
Thread
Length(in.)
Shank
Length (in.)
Qty
Non-Combo
Item No.
DX 35
DX E72
DX 351
DX 350
DX 36M
DX 460
1/4" Stainless studs for steel
X-CR W6-11-12 FP8
3/8"
1/2"
100
00255904
7/8"
3/8"
1/2"
1"
100
1/4" Stainless studs for concrete
X-CR W6-22-12 FP8

X-CR W6-11-27 FP8
00255905
00255906
X-CR W6-22-27 FP8
00255907
00306483
1/2"
100
100
X-EW6-11-12 FP8
7/8"
3/8"
1"
1/4" Studs for steel
7/8"
1-3/16"
1-1/2"
3/4"
1/2"
1/2"
1/2"
11/32"
100
100
100
100
00306116
00306119
00306484
00306125
1/4" Hardened studs for high strength steel
X-EW6-20-12 FP8
X-EW6-28-12 FP8
X-EW6-38-12 FP8
X-EW6H-20-9 FP8
1/4" Studs for concrete
X-EW6H-20-12 FP8
X-EW6H-30-12 FP8
X-EW6H-38-12 FP8
X-W6-11-22 FP8
3/4"
1-3/16"
1-1/2"
3/8"
1/2"
1/2"
1/2"
7/8"
100
100
100
100
00306126
00239344
00239345
00306486
X-W6-11-27 FP8
W6-20-22 FP8
W6-20-27 FP8
W6-38-27 FP8
3/8"
3/4"
3/4"
1-1/2"
1"
7/8"
1"
1"
100
100
100
100
00306487
00306073
00306074
00306075
www.us.hilti.com
6.43

Fastener Program
1/4" Threaded studs

Thread
Length(in.)
Shank
Length (in.)
Qty
3/8"
7/8"
1000
Combos include threaded studs and boosters packaged separately. X-W6-11-22FP8 Combo
X-W6-11-27FP8 Combo
X-W6-20-22FP8 Combo
X-W6-20-27FP8 Combo
1/4" Studs for steel - Combo
X-EW6-11-12FP8 Combo
3/8"
3/8"
3/4"
3/4"
3/8"
7/8"
1"
7/8"
1"
1/2"
1000
1000
1000
1000
1000
95834
Combos include threaded studs and boosters packaged separately. X-EW6-20-12FP8 Combo
3/4"
1/2"
1000
95835
3/8"
3/4"
1 3/16"
3/4"
1/2"
1/2"
1/2"
11/32"
1000
1000
1000
1000
3/4"
3/4"
3/4"
1/2"
11/32"
1/2"
1000
1000
1000
Description
1/4" Studs for concrete - Combo
1/4" Hardened studs for high strength steel - Combo
X-W6-11-22FP8 Combo
X-EW6H-20-8FP8 Combo
Combos include threaded studs and boosters packaged separately. X-EW6H-20-12FP8 Combo
Non-Combo
Item No.
DX 35
DX E72
DX 351E
DX 350
DX 36M
DX 460
95838
95839
95840
95841
95838
95839
95840
95841
95838
95839
95840
95841
95838
95839
95840
95841
95842
95843
95844
95842
95843
95844
95842
95843
95844
95842
95843
95844
95845
95846
95845
95846
95845
95846
95845
95846
95833
95836
95837
3/8" Threaded studs

Description
Thread
Length(in.)
Shank
Length (in.)
Qty
Non-Combo
Item No.
DX 600N DX A41 I
3/8" Studs for concrete
W10-30-27P10
1 3/16"
1"
100
00026472
3/8" Studs for steel
W10-30-32P10
W10-30-42P10
EW10-30-15P10
1 3/16"
1 3/16"
1 3/16"
1 1/4"
1 5/8"
37/64"
100
100
100
00026473
00026476
00026569
3/8" Studs for concrete - Combo
W10-30-27P10 Combo
1 3/16"
1"
1000
299261
299265
1 3/16"
1 3/16"
1 3/16"
1 1/4"
1 5/8"
37/64"
1000
1000
1000
299262
299263
299264
299266
299267
299268
1 3/16"
1"
1000
299269
299273
1 3/16"
1 3/16"
1 3/16"
1 1/4"
1 5/8"
37/64"
1000
1000
1000
299270
299271
299272
299274
299275
299276
Combos include threaded studs and boosters packaged separately. W10-30-32P10 Combo
W10-30-42P10 Combo
3/8" Studs for steel - Combo
EW10-30-15P10 Combo
Combos include threaded studs and boosters packaged separately.
3/8" Studs for concrete with coupler - Combo
W10-30-27P10 Combo w/ coupler
Combos include threaded studs and boosters packaged separately. W10-30-32P10 Combo w/ coupler
W10-30-42P10 Combo w/ coupler
3/8" Studs for steel with coupler - Combo
EW10-30-15P10 Combo w/ coupler
Combos include threaded studs and boosters packaged separately.
www.us.hilti.com
6.44
DX 600N Selector Guide
DX 600N
Stabilizers
6N/S1
00006461
6N/S1-3
00006485
6N/S1-4
00006486
6N/S4
00006223
ROUND
DEEP LIMITED ACCESS
HS-158 HILTI STRUT
STOP SPALL
6N/S2
00006462
6N/S5
00006465
STANDARD
NARROW ACCESS
Guides
6N/S7
00006467
12mm
00006188
EXTRA NARROW ACCESS
Stop Ring
Pistons
6N/F1
00006411
6N/F2
00006412
6N/F3
00006413
12mm
10mm
8mm
6N/DN1
00006529
6N/DS
00006531
6N/W6-11
00006556
6N/W6-20
00006557
6N/W6-28
00006558
6N/W6-38
00006559
DX 600N Selection Chart

GUIDES
PISTONS
Fasteners
STP RNG
12mm
00006188
STABILIZERS
6N/S1
00006461
6N/S1-3
00006485
6N/S1-4
00006223
6N/S4
00006223
6N/S2
00006462
6N/S5
00006465
6N/S7
00006467
6N/F1
00006411
6N/F2
00006412
6N/F3
00006413
6N/DNI
00006529
6N/DS
00006531
6N/W6-11
00006556
6N/W6-20
00006557
6N/W6-28
00006558
6N/W6-38
00006559
Recommended
Solution
Description
X-CR
STAINLESS STEEL
X-AL
HIGH STRENGTH
X-(E)DNI
STANDARD PIN
E(DS)
HEAVY DUTY PIN
(E)W6-11-D12
1/4" THREADED STUD
(E)W6-20-D12
1/4" THREADED STUD
(E)W6-28-D12
1/4" THREADED STUD STEEL
(E)W6-38-D12
1/4" THREADED STUD
(E)W6-FP8
1/4" THREADED STUD
(E)W10
3/8" THREADED STUD
TB-P12
EYE PIN
www.us.hilti.com
6.45
DX 35 Selector Guide
DX 35
Baseplates
Guides
21/S1
00002556
(ROUND)
21/S2
00002557
(TAPERED)
Pistons
21/F3-1
00002554
21/F2-1
00002553
21/SDF
00002565
21/SDF-R
00002018
REDUCED POWER
DX 35 Selection Chart
Recommended Solution
BASEPLATES
GUIDES
PISTONS
Fasteners
Description
X-CR
STAINLESS STEEL
HIGH STRENGTH
STANDARD PIN
X-ZF
COMBO PIN
X-DNI S15/36
PINS W/ 26/36mm WASHER
ESD
DRYWALL TRACK TO STEEL
CC20, CC27
CEILING CLIP
EMTC
CONDUIT CLIP
CTV
CABLE CLIP
X-AL
X-(E) DNI
21/AL
00241400
21/SDF-R
00002018
21/SDF
00002565
21/F4-2
00299232
21/F2-1
00002553
21/F3-1
00002554
Options
(Part prefix numbers must match)
Example Option 1:
X-DNI pin fastened with
baseplate 21/S2, guide 21/F2-1
and piston 21/SDF-R
21/S2
00002557
21/S1
00002556
Possible Solution
www.us.hilti.com
6.46
DX 35 1/350 Selector Guide
DX 351
Magazine
MX32
00339474
GUIDES
Fasteners
Narrow Access
Pistons
X-P8S-351
00331047
X-P8AL-351
00331194
Piston Tip
Piston Tip
PISTONS
X-P8L-351
00331193
Narrow Access
X-FG8ME-351
00331300
P8L-351
00331193
Possible solution
* 14mm to 32mm Only
* * CPL = Complete
Standard
MAG.
P8AL-351
00331194
MX27
00333315
P85-351
00330147
FG8L-351
00331206
MX27
00333315
X-FG8ME-351
00331300

Recommended solution
F68L-351
00331206
Guides
Description
X-CR
STAINLESS STEEL
X-AL
HIGH STRENGTH
X-DNI
STANDARD PIN
X-EDNI
PIN FOR STEEL
X-DW
PIN FOR DRYWALL TRACK
X-ZF, X-CF
ECONOMY PIN
X-DNI MX
COLL. FASTENERS 10/STRP
X-DW MX
PIN FOR DRYWALL TRACK
XZ-F MX
X DNI, S12, S23/36
PINS W/ 12mm WASHER
ESD16
CC20, CC27
CEILING CLIP
Piston Tip
DX 350
Baseplates
Guides
2/S13
00002363
2/S13-1
00078482
2/S14-1
00002397
2/S14-2
00002398
STANDARD
HS-158 HILTI STRUT
LIMITED ACCESS
DEEP LIMITED ACCESS
2/F3
00002303
2/F4
00002304
2/F4-2
00002330
DX-350 Selection Chart

Recommended
Solution
Pistons
2/DN-1
00002413
1,2
X-(E) DNI
STANDARD PIN
2
2
2
1
1
1
2
2
2
1,2
1,2
1,2
2/AL
00224799
2/F4-2
00002330
1
1
1
2/K
00002416
2/F4
00002304
HIGH STRENGTH
Slightly longer piston for fastening

through sprayed on insulation
2/F3
00002303
2/S14-2
00002398
STAINLESS STEEL
X-AL
Fasteners
www.us.hilti.com
Options (Numbers of parts must match)

Example:
Option 2 - X-DNI pin fastened with baseplate
2/S14-2, guide 2/F4-2 and piston 2/AL or
2/DN-1
X-CR
6.47
PISTONS
2/S14-1
00002397
1,2
2/S13-2
00002399
2/AL
00224799
2/S13-1
00007848
2/K
00002416
2/S13
00002363
2/DN-1
00002413
GUIDES
BASEPLATES
Possible
Solution
Description
X-ZF, X-CF
COMBO PIN
X-DNI S26/36
1,2
A
A
A
SL
FORMING NAIL
ESD
(E)W6-FP8
1/4" THREADED STUD
CC20, CC27
CEILING CLIP
EMTC
CONDUIT CLIP
CTV
CABLE CLIP
BC
REBAR BASKET CLIP
GC
GUNITE CLIP
1,2
1,2
1,2
DX 36M Selector Guide
DX 36M
Baseplates
36/S13
00003738
36/S13-1
00003046
36/S14-1
00003791
36/S14-2
00003047
36/S19
00003795
36/IE
00003207
STANDARD
HS-158 HILTI STRUT
LIMITED ACCESS
DEEP LTD. ACCESS
MAGNETIC3
For 80-120mm
X-IE
36/AL
00003483
Optional
Accessories
Guides
Pistons
36MX
00003293
36/DN-L
00003171
36/DNN
00003726
36/IE
00003185
STANDARD
36/F3
36/F4
36/F4-2
36/IE
00003737 00003780 00003045 00003184
36/BV STOP SPALL

00003778
FITS ONTO 36/S13 AND

36/S16 BASEPLATES
STD.
DX 36M Selection Chart

Recommended
Solution
MAG.
BASEPLATES
GUIDES
PISTONS
1, 2, 3
Fasteners
Options (Numbers of
parts must match)
Example:
Option 2 - X-DNI pin fastened with baseplate
36/S14-2, guide 36/F4-2
and piston 36 AL
36-S13
00003738
36/S13-1
00003046
36/S14-1
00003791
36/S14-2
00003047
36/S16
00003792
36/MXS
00003335
36/S19
00003795
36/IE
00003207
36/MX32
00003466
36/MX62
00003467
36/F3
00003737
36/F4
00003780
36/F4-2
00003045
36/F10
00003783
36/IE
00003184
36/AL
00003483
36/MX
00224740
36/DN-L
00003171
36/DNN
00003726
36/IE
00003185
Possible
Solution
Description
X-CR
STAINLESS STEEL
1,2
X-AL
HIGH STRENGTH
1,2
X-(E)DNI
STANDARD PIN
1,2
X-ZF, X-CF
COMBO PIN
1,2
X-DNI-MX
COLLATED FASTENERS
X-ZF-MX
COLLATED FASTENERS
X-DNI S23/36
SL
FORMING NAIL
ESD
X-IE
INSULATION
(E)W6-FP8
1/4" THREADED STUD
CC20, CC27
CEILING CLIP
EMTC
CONDUIT CLIP
CTV
CABLE CLIP
BC
REBAR BASKET CLIP
3
3
1
1,2
www.us.hilti.com
6.48
DX A40 Selector Guide
DX A40
Fastener Guides/Magazine
Pistons (X-AP)
X-AF 8K3
00232520
X-AF 8K
00004692
X-AF 8K7
00232524
LIMITED ACCESS
X-AF 8K GRATING
00232525
X-4 8K/E
00267822
ECH
X-AF 8KL
(CO-ACTING)
00004834
X-AF 8K2
00232519
LIMITED ACCESS
X-AF IE
00232636
X-AF 8K-S12
00232508
X-AP 8K-AL
00004796
X-AP 8K-DNI
00232376
Piston Tip
Piston Tip
X-AP KWIK 1 X-AP GRATING

00232310
00267865
X-AP IE52
00004745
Piston Tip
X-AP 8K1
00232754
Limited Access
X-AP-8K/E
ECH
00232543
DX A40
208
X-AM32
00232369
X-AM32
Piston Tip
Piston Tip
Piston Tip
Piston Tip
DX A40 Selection Chart

FASTENER GUIDE/BASEPLATES
MAG.
PISTONS
BUFF.
Fasteners
Description
X-CR
STAINLESS STEEL
X-AL*
HIGH STRENGTH
X-DNI
STANDARD PIN
X-EDNI
PIN FOR STEEL
X-ZF, X-CF
ECONOMY PIN
X-DNI-MX*
X-ZF-MX*
X-DNI S12
PINS W/ 12mm WASHER
X-DNI S23/36
ESD16
X-IE
INSULATION
(E)W6-FP8
1/4" THREADED STUD
CC20, CC27
CEILING CLIP
EMTC
CONDUIT CLIP
CTV
CABLE CLIP
BC
REBAR BASKET CLIP
X-RE
REMOVABLE FASTENER
X-FCM
GRATING SYSTEM
X-FCP
CHECKERPLATE
CHARACTER
MARKING
ECH
CABLE HOLDERS
www.us.hilti.com
6.49
X-AA 8 (5 PACK)
00251519
X-A-8K/E ECH
00232543
X-AP 15H
00267900
X-AP 8K GR
00267865
X-AP 8K KWIK 1
00232310
X-AP 8K IE
00004745
X-AP 8K-DNI(Standard)
00232376
X-AP 8K AL
00004796
MAGAZINE X-AM32
00232369
X-A 8K/E ECH

00267822
X-AF 8K CPL
00004692
X-AF IE CPL
002300636
X-AF 8K-S12 CPL

00232508
X-AF 8KL CPL

00004834
X-AF 8K3 CPL*(STD.)

00232520
X-A40 CM
00268160
X-A40 HM
00267999
* 14mm to 32mm Only

* * CPL = Complete
X-AF 8K Grating
00232525
Possible solution
DX 460 / DX A41 Selector Guide
DX 460 / DX A41
Fastener Guides/Magazine
X-460 F8
00373313
X-460-F10
00373319
X-460-F10-SS
00373320
MX-SM
00370827
Stop Spall
Magazine
X-460-P8W
X-460-P8AL
X--460-P8I
X-460-PSM
00373298
00373299
00373297
00373303
Piston Tip
Piston Tip
Magazine
X-460-F1E
00373321
X-460 F8N15
00373314
LIMITED ACCESS
X-460 F8 N10
00373315
LIMITED ACCESS
8,4
8,4
208
208
X-MX72
00370844
Pistons (X-AP)
X-460 P10
X-460 PIE
00373300
00373301
Piston Tip
Piston Tip
Piston Tip
DX 460/DX A41 Selection Chart
Fasteners
X-460-B
00373330
X-460 PSM
00373303
X-460 P8W
00373298
BUFF.
X-460-PIE
00373301
X-460P10
00373300
X-460 P8AL
00373299
X-460P8
00373297
MAG. MX-SM
00370827
MAG. X-MX72
00370899
PISTONS
X-460-FIE
00373321
X-460 F10
00373319
X-460 P8
00373313
Possible
Solution
X-460 P8N10
00373315
Recommended
Solution
X-460 P8N15
00373314
FASTENER GUIDES/MAGAZINE
Description
X-CR
STAINLESS STEEL
X-AL
HIGH STRENGTH
X-DNI
STANDARD PIN
X-EDNI
STEEL PIN
X-ZF, X-CF
COMBO PIN
X-DNI-MX
COLLATED FASTENERS
X-DW-MX
X-ZF-MX
COLLATED FASTENERS
X-DNI S12
PINS W/ 12mm WASHER
X-DNI S23/36
SL
REMOVABLE FORMING NAIL
X-IE
INSULATION
(E)W6-FP8
1/4" THREADED STUD
(E)W10-P10
3/8" THREADED STUD
CC20, CC27
CEILING CLIP
EMTC
CONDUIT CLIP
CTV
CABLE CLIP
BC
REBAR BASKET CLIP
X-RE
REMOVABLE FASTENER
ZF MX
FLOORING APPLICATIONS
ALL
NARROW ACCESS
HSN
DECKING PIN
www.us.hilti.com
6.50
DX 750
75/HVB 75/ENP2-L
00023524 00023268
75/NPH2
00023428
75/ENP2K-L
00023360
75/HM
00023451
75/10G
00023447
Magazine
BASEPLATES
MX75 Magazine
00023456
STOP
RING
PISTONS
STOP RING
00023139
75/10G
00023447
75/HM
00023451
75/HVB
00023524
APPLICATION
75/ENP2K-L
00023360
FASTENERS
75/NPH2
00023428
75/ENP2-L
00023268
75/S10-G
00023444
75/ENP2-S
00023132
75/S10 G
00023444
75/HVB
00023525
75/F10-G
00023449
75/S3
00023414
75/S3
00023414
Pistons
75/HVB
00023525
75/S2
00023394
Guide
75/S2
00023394
Baseplate Assemblies
ENP2
DECKING
TO STEEL
ENP2K
ENPH2
NPH2
TO CONCRETE
EM8/M8/X-CRM8
GRATING
CHARACTERS
STEEL MARKING
ENP2
SHEAR CONNECTOR
www.us.hilti.com
6.51
DX 450
45/S3
00000779
STANDARD
LIMITED ACCESS
Stop Ring
45/F1
00000729
45/F3
00000781
45/NK
00000748
DX450 Selection Chart
ENKK
STOP RING
12MM
00000855
45/NK
00000748
APPLICATION
PISTONS
45/F3
00000781
FASTENERS
GUIDES
45/S3
00000779
BASEPLATES
Recommended
Solution
45/F1
00000729
12mm
00000855
45/S2
00000775
NORMAL
45/S2
00000775
45/S1
00000731
45/S1
00000731
Piston
Guides
Baseplates
DECKING
TPRS
www.us.hilti.com
6.52
a HIT for all seasons

HIT RE 500 23F (-5C) to 115F (46C)
F
-10
23
40
60
90
104
115
C -23
-5
15
32
40
46
HIT HY 150 & HY 20

F
104F (40C) down to 23F (-5C)
-10
23
40
60
90
104
115
C -23
-5
15
32
40
46
HIT ICE down to -10F (-23C)

F
-10
23
40
60
90
104
115
C -23
-5
15
32
40
46
Anchoring Systems
Heavy Duty
HVU Adhesive Capsule
HIT RE-500 Epoxy Adhesive
HIT HY 150 Adhesive
HIT TZ Threaded Anchor
HDA Heavy Duty Mechanical Anchors
HSL Heavy Duty Expansion Anchor
Page 7.20+
Page 7.10
Page 7.11
Page 7.14
Page 7.23+
Page 7.25+
Hollow Base
HIT HY 20 Adhesive
Page 7.15+
Cold/Specialty
NEW !
HIT-ICE
Page 7.12
Medium Duty
KWIK Bolt II Expansion Anchor
HCKB14 Anchor
HCA Coil Anchor
HDI Drop In Anchors
HLC Sleeve Anchor
Page 7.28+
Page 7.31
Page 7.32
Page 7.33+
Page 7.38+
Light Duty
KWIK-CON Masonry Fastening System
TapCon Masonry Fastening System
Metal HIT Anchor
HPS-1 Impact Anchor
Toggler Bolt
KwikTog
HSP/HFP Drywall Anchor
HUD-1/HUD-L Anchor
IDP Insulation Anchor
Light Duty Assortment (LDA) Kit
Split Bolt
Expansion Shields
Page 7.40+
Page 7.44+
Page 7.46
Page 7.47
Page 7.48
Page 7.49
Page 7.50
Page 7.51
Page 7.52
Page 7.53
Page 7.54
Page 7.54
Technical Resources
Hilti North America Technical Guide
Online Design Center www.us.hilti.com/anchordc
www.us.hilti.com
Anchoring Systems
System
Features
HIT-RE 500 Epoxy

Adhesive
Conforms to ASTM C881 meeting most DOT and Federal

project specifications
ICBO AC58, ASTM E 1512 testing allows usage in wet holes
ICBO AC58, ASTM E 1512 testing allows usage in seismic
applications
Fast, easy dispensing in cold concrete temperatures
23F (-5C) to 115F (46C)
Virtually odor-free allowing continuous work in confined areas
Contains no hazardous chemicals for worker safety as well as
easy storage and transportation
NSF/ANSI Standard 61 approval for use in potable water
Suitable for use in underwater applications
7.10
HIT HY 150 Adhesive
HIT-TZ threaded rods with HIT HY 150 can be set in uncleaned,

water-filled and/or diamond cored holes
Fast cure allows quick bolt ups
Seismic tested per ICBO AC58, ASTM E 1512
NSF/ANSI Standard 61 approval for use in potable water
Virtually odor free for applications indoor or in confined spaces!
Contains no hazardous chemicals
Outstanding high temperature performance
Cleans up with soap and water
Large 37 oz or 11.1 oz cartridge
7.11,
7.14
HVU Adhesive
Capsule
No hole brushing required, just blowing out hole with

compressed air makes installation fast and easy
Arrowhead shaped capsule stays in the hole for easy overhead
installations
HVU aggregate roughens hole which allows for use in Hilti
matched tolerance diamond cored holes
ICBO AC58, ASTM E 1512 testing for usage
in seismic applications and damp holes
NSF/ANSI Standard 61 approval allows for use in
potable water
HVU combined with HIT HY150 allows for underwater
installations
7.20
HDA Heavy Duty

Mechanical Anchor
Self-undercutting anchor installs in one minute. For a fast and

easy setting operation.
Fastening quality comparable to cast-in headed studs
Excellent for resisting seismic, shock and fatigue loads
Fully removable for temporary fastening
Minimal expansion forces during installation allow small edge
distance and close anchor spacing
Reliable ductile steel failure in virtually all strengths of
concrete 2500 psi
Undercut allows use in tension zones and cracked concrete
HDA-T version allows use of fewer fasteners in high shear
load applications
Available sizes M10 (3/8") to M20 (3/4")
Sherardised (H.D.G.) and 316 stainless available
7.23+
HSL Heavy Duty

Expansion Anchor
ICBO AC01 testing allows usage in seismic applications

Bolt head versions available to provide flexibility of flush
mounted, low profile applications
HSL-I M12 (1/2") is perfect for applications requiring a
flush-mounted fastener
Steel spacer sleeve allows use of fewer fasteners in high shear
load applications
Heavy-duty expansion sleeve and collapsible mid section
provide positive clamping of fastened materials to concrete
Heavy-duty expansion sleeve allows installation in Hilti matched
tolerance diamond-cored holes
Heavy-duty expansion sleeve provides follow up expansion for
fastenings in tension zones of concrete such as under bridge
decks, floor slabs and beams
7.25+
HIT HY 20 Adhesive
High load performance allows use in a wide range of hollow

base materials including hollow concrete block, terra cotta,
solid brick or with holes, multi-wythe brick walls and
composites
URM tested for use in seismic regions
Fast curing for high productivity and fast threaded rod usage
Formulated for easy installation in freezing temperatures
allowing year round installation
Virtually odor free allowing contiuous work in confined areas
Contains no hazardous chemicals for worker safety
as well as easy job site storage and transportation
Large 37 oz cartridges for high volume or 11.1 oz cartridges
for small to meduim-sized projects provide increased flexibility
Formula allows soap and water cleanup
7.15+
Hollow Base
Heavy Duty
HIT-TZ Threaded
Anchor
7.3
Page
Anchoring Systems
System
Features
Page
Cures at low temperatures down to -10F (-23C)

HIT-TZ threaded rods with HIT-ICE can be set in uncleaned,
water-filled and/or diamond cored holes
High performance in concrete
Fast curing for high productivity
Good handling due to low dispensing force
Nonstructural crack filler
Stone, masonry
7.12
Kwik Bolt II
Expansion Anchor
Impact section (Dog Point) prevents thread damage

during installation
Independent 3-piece wedge with dimples prevents anchor from
spinning during installation
Length identification code facilitates quality control
and inspection after installation
Anchor size is same as drill bit size for easy installation
Comprehensive performance testing to provide high and
consistent performance in concrete, light-weight
concrete & grout filled block base materials
Mechanical expansion allows immediate load application
Can be installed through the fixture, improving productivity
7.28+
HCKB14 Anchor
7.31
HCA Coil Anchor
Hex Head enables low profile fastening

Removable and reusable provides cost savings
Stud type anchor design allows easy through type
fastenings and can be set in bottomless hole
Depth set mark on the anchor shank assists
in proper installation
Low cost disposable coil keeps costs to a minimum
Pre-assembled anchors ensure easy and fast installation
7.32
HDI Flush Mount

Internal Thread
Anchor
HDI
Anchor, setting tool & Hilti drill bit form a matched
tolerance system to provide reliable fastenings
Below surface setting for easy patchwork
Allows for shallow embedment without sacrificing performance
7.33+
HDI-L Flush Drop-in

Anchor
HDI-L
Lip provides flush installation, consistent anchor depth,
and easy rod alignment
Lip allows accurate flush surface setting, independent
of hole depth and ideal for repetitive fastenings with
threaded rods of equal length
Intelligent expansion section adapts to the base material and
reduces number of hammer blows up to 50%
NEW!
Medium Duty
Cold / Specialty
HIT-ICE
HDI-P Drop-in
Anchor
Independent 3-piece wedge

Enlarged eyelet
Reinforced head
Reinforced gripping area
Enhanced collar area
Accommodates two #9 wires or one 1/4" penrod
Optimized 3/4" anchor length to allow reliable fastenings in

hollow core panels, pre-cast plank and post tension slabs
Shallow drilling enables fast installation
Lip provides flush installation, consistent anchor depth, and easy
rod alignment
Setting tool leaves mark on flange when anchor is
set properly to enable inspection & ensure reliable
installation
7.35
7.4
Light Duty
Medium Duty
Anchoring Systems
7.5
System
Features
Page
HDI-S
Speed Thread
Mechanical Anchor
Designed to accept coil rod, and used in combination with the

standard Hilti HDI setting tool and drill bits: the reliable HDI-S
speed thread drop-in anchor forms a matched tolerance
system for your forming applications.
Ideal for temporary concrete forming application, i.e. bridge,
highway, tunnel and subway constructions and repair, the HDI-S
can be used in solid concrete, hard stone and solid block.
7.36+
HLC Sleeve Anchor
Stud type anchor design allows easy through-type fastenings

and can be set in bottomless hole
Pre-assembled anchor ensures easy and fast installation
Anchor size is same as drill bit size for easy installation
Variety of head styles, lengths and sizes allow for versatile
applications
Comprehensive testing to provide high performance in block,
masonry and concrete base materials
7.38+
KWIK-CON Masonry
Fasteners
Hilti's unique system of matched tolerance drill bits and

tri-lobular screw design provide the highest performance values of
any comparable system on the market.
Choice of head styles: Torx Hex Washer Head for fast, secure
driving; Torx or Phillips Flat Head for countersinking
applications.
Matched tolerance carbide-tipped drill bit supplied with each
combo box of KWIK-CON II+ fasteners
Exclusive internal torx drive
Choice of 3/16", 1/4" and 3/8" diameter fasteners
Fasteners protected by corrosion resistant coating; stainless
steel fasteners available in select sizes
7.40+
TapCon Masonry
Fastening System
3/16 and 1/4 Anchor diameters, with additional sizes

available through our specials offering
Hex Head and Phillips Flat Head styles available to suit
customer needs
Save time with the Comprehensive TapCon DeLuxe Driver
Installation Kit: Designed to work with drill bits in placeno
need to remove the drill bit to set the anchor!
Matched Tolerance Drill bits in straight-shank and SDS and HEX
design
7.44+
Metal HIT Anchor
Quick and easy fastening for maximum speed and installation

Low profile mushroom head style provides a nice
finish and tamper proof fastening
Anchor design allows easy through-type fastenings
even in bottomless holes
Thorough test data for safe light duty
fastenings in concrete and masonry
Choice of Stainless Steel or Carbon Steel finish
allows for indoor or outdoor use
7.46
HPS-1 Impact
Anchor
Phillips drive connection is recessed in the screw head

providing protection during hammering, allowing simple setting
and removal
Anchor collar and screw head form a compact unit which
allows for countersinking in soft wood and solid clamping
action with metal parts
Expanding head opens in hollow base material to provide
reliable keying effect
One type anchor reduces inventory, providing versatile
use in brick, hollow block and concrete
Can be set with hammer or screw driver for quick and easy
installation
7.47
Specialty Light Duty
Light Duty
Anchoring Systems
System
Features
Toggler Bolt
Unique installation legs and locking cap facilitate

fastenings in wide range of drywall and hollow wall
materials up to 2-1/4" thick
One piece metal channel provides greater holding power
Plastic pull ring assists in setting lock cap (3/8" & 1/2")
Anchor is adjustable for various base material thicknesses for
easier installation as well as minimum inventory investment
Remains mounted in the wall without screw for convenient
handling, installation and reuse
Comprehensive offering with and without machine screws
7.48
KwikTog
Unique one piece design for easy setting

Three convenient sizes for use in a variety of hollow
base materials from 1/4" drywall to block and concrete
Leg braces provide added support
Ribs on body help prevent anchor from spinning
during installation
Remains mounted in the wall without screw for
convenient handling, installation and reuse
7.49
HSP/HFP Drywall
Anchor
Shark tooth design for correct positioning and

quick installation
Cuts its own thread no pre-drilling necessary
One Hilti bit for anchor and screw setting
Can be set with electric or standard screwdriver
for quick and simple installation
Removability adds to the anchors versatility
Available in non-conductive nylon or zinc for
a variety of applications
Available with and without screws for your convenience
7.50
HUD-1/HUD-L
Anchor
Precisely controlled screw guidance prevents wandering and

keeps the screw within the anchor shank
Flared collar makes the anchor suitable for pre-installation or
installation through fixtures
Anti rotation wings help prevent the anchor from rotating
or falling out during installation
Four way expanding head enhances keying effect
in hollow base material
Forms a keying knot when installed in hollow material
to improve holding values
Available with and without screws
7.51
IDP Insulation
Anchor
Specially structured head to help ensure bonding

of plaster applied directly over the anchor
Suitable for insulation thickness up to 4-3/4"
for enhanced versatility
Installation in concrete and masonry allow versatile use
No metal parts which reduces potential condensation behind
finish coat of EIF systems
7.52
LDA Kit Box
One box with anchors for a wide range of base materials

A compact unit to move from job to jobno loose parts
The potential to customize the box after the
initial purchase
The opportunity to use new product without
purchasing box quantities
7.53
Page
7.6
Specialty Light Duty
Anchoring Systems
System
Features
Split Bolt
For use in concrete and stone

One-piece pre-expanded anchor
7.54
Expansion Shields
7.54
single
For use in concrete, block, brick and stone

Removable
Corrosion resistant
Internally threaded
Page
double
Lag Shield
www.us.hilti.com

Tech Center
Technical Resources
click on tool bar
Online Resources:
Anchor System Advisor
Make anchor selection
based on design criteria.
Anchor System Overview
Browse Hilti anchors by
base material and type.
Hilti Anchor Program*
Download or place an order
for Hilti anchor design
software.
Anchors used in conjunction
with fire
Resistive construction
Anchor guide specification
Anchor CAD details
Base materials
Evaluation of test data
Anchor terminology
Anchor working principles
Design considerations
Corrosion
Design Center
click on Anchor
For complete anchor setting instructions and

product information.
* This version is for U.S. only and will

not ship internationally.
er
Summ
2004
ProfIs
Professional
7.7
Anchor Calculation
Software
HIT Adhesive Anchors, Hilti Injection Technique
Hilti Injection Technology System A HIT For All Seasons

A Versatile, Easy-To-Use Adhesive Anchoring Aystem for Faster Cure and use in Extended Temperature Ranges
HIT RE 500
HIT HY 150 & HY 20
HIT-ICE
23F (-5C) to 115F (46C)
104F (40C) down to 23F (-5C)
down to -10F (-23C)
For hot environments and/or deep

embedment fastenings, HIT RE 500 is a slow
curing epoxy for use in solid base material
temperatures from 23F (-5C) to 115F (46C).
RE 500s formulation allows for installations in
oversized or diamond cored holes and
underwater applications down to 165 feet (50
meters).
Hilti HIT HY 150 and HY 20 are hybrid adhesives

consisting of a methacrylate resin, hardener,
cement and water.
HIT HY 150 is for solid base material installations
while HIT HY 20 is specifically formulated for
hollow base material fastenings. Both HY 150
and HY 20 are fast curing adhesives for use in a
wide range of base material temperatures from
104F (40C) down to 23F (-5C).
For colder environment installations, HIT-ICE

adhesive is a winter formulation for solid base
material temperatures down to -10F (-23C), as
well as a quick setting solution in warmer
temperatures. HIT-ICE consists of a methacrylate
resin and hardener.
Very suitable for application

page 7.10
May be suitable per application
Application
HIT RE 500
page 7.11
page 7.15
HIT HY 150
HIT HY 20
page 7.12
HIT-ICE
Open Gel Time Table (approximate)*

Base Material
Temperature
ICBO
NSF ANSI
STD 61
Drinking Water
Diamond
Cored
Holes
with HIT-TZ
with HIT-TZ
-10 -23
0 -18
23 -5
32
0
41
5
68 20
86 30
104 40
115 46
HIT RE 500 HIT HY 150 HIT HY 20
4 hrs
3 hrs
2 hrs
30 min
20 min
12 min
7 min
25 min
18 min
13 min
5 min
4 min
2 min
-
40 min
30 min
20 min
6 min
3 min
1 min
-
HIT-ICE
1.5 hrs
1.5 hrs
40 min
26 min
11 min
4 min
1.5 min
-
* Product temperatures must be maintained above 41F (5C), except HIT-ICE must be above 0F (-18C)
Drilled
Holes
Final Cure Time Table (approximate)1

Initial Cure Time
Base Material
Temperature
Oversized
Holes
F
with HVU
Underwater
Solid Base
Hollow
Base
-10 -23
0 -18
23 -5
32
0
41
5
68 20
86 30
104 40
115 46
25% of Working Load
HIT RE 500 HIT RE 500 HIT HY 150 HIT HY 20
36 hrs
25 hrs
12 hrs
6 hrs
4 hrs
2 hrs
78 min
72 hrs
50 hrs
24 hrs
12 hrs
8 hrs
4 hrs
2.6 hrs
6 hrs
4 hrs
2 hrs
1 hrs
45 min
30 min
-
6 hrs
3 hrs
90 min
50 min
40 min
30 min
-
HIT-ICE
24 hrs
24 hrs
6 hrs
4 hrs
2 hrs
1 hr
30 min
-
1 Product temperatures must be maintained above 41F (5C), except HIT-ICE must be above 0F (-18C)
www.us.hilti.com
7.8
Heavy Duty Anchor
The Hilti HIT System

Versatile, Easy-To-Use, Offers Faster Cure Times and Extended Temperature Ranges
HIT HY 150,
HIT RE 500 or
HIT-ICE
Adhesive for fastening into solid
base material such as concrete,
grouted block and stone.
HIT HY 20
HIT HY 20
Adhesive with screen tube

for fastening thru masonry
construction with voids.
Adhesive with screen tube

for fastening to hollow
block, hollow clay tile, and
solid brick or with holes.
Hilti System Advantages
HIT Applications
Versatile
For fastening a variety of fasteners into many

different base materials within a wide range of
temperatures.
A) HIT HY 150, HIT-ICE

or HIT RE 500
Easy To Use
Rebar doweling into solid

concrete. Quick and easy.
Easy dispensing adhesive even in cold temperatures.

Application-matched, compact system; simply drill
and clean the hole, dispense the adhesive and insert
the fastener or rebar.
B) HIT HY 150/HIT-ICE
Uniform Quality
C) HIT HY 150/HIT-ICE
with HIT-TZ or HAS-E
Threaded Rods
Anchorage of threaded rod

into solid grouted bond
beam.
Mixing errors eliminated; two components of the

adhesive are in separate containers and are
proportional and mixed as they are dispensed.
Reliable
Consistent fastenings; no expansion forces exerted on
base material.
D) HIT HY 20
Clean
With screen tube. 22.5

combination anchor for
seismic upgrade in
unreinforced masonry
(URM) and solid brick
walls.
No direct contact with the adhesive, since there is no

manual mixing; no setting tools required.
Economical
Waste is minimal since only the amount required for
the job is used. If adhesive is not completely
dispensed during initial usage, cartridge may be
reused; one cartridge may be sufficient for several
fastenings. Cartridge waste volume for disposal is
also minimal.
E) HIT HY 20
With screen tube. Veneer
wall pinning using rebar or
HAS rods as brick tie for
building renovation.
HIT-TZ Advantages
Reliable
Holes may be uncleaned, waterfilled or both and

the high performance remains the same as
cleaned dry holes with Hilti HAS-E threaded
rods at 20% deeper embedment. Even in
diamond cored holes made with the Hilti
EC-1, the HIT-TZ is fast and reliable.
Simple
20% less embedment than standard

embeded threaded rods uses less
HIT HY 150/HIT-ICE and saves drilling,
cleaning and inspection time. Drill bit
life is also extended more than 20%.
With screen tube.

Anchorage to face of
hollow concrete block
using HIT-A anchor rod or
HIT-I internally threaded
insert.
With screen tube.
Anchorage to face of brick
with holes using HIT-A rods
or HIT-I internally threaded
inserts.
Fast
Economical
F) HIT HY 20
G) HIT HY 20
Installs easily with the Hilti HIT HY 150/HIT-ICE

injection adhesive.
No cleaning, less drilling and fast curing
HIT HY 150/HIT-ICE .
Anchorage to solid base

materials.
Secure
HIT TZ not only means trouble zones of uncleaned
holes, but tension zones of concrete where cracking
occurs e.g. overhead.
7.9
Heavy Duty Anchor
HIT RE 500 Epoxy System: Solid Base Material

The New Power of Injection
23F (-5C) to 115F (46C)
Listings
High performance
The new Hilti HIT RE 500 epoxy system leaves nothing to
chance. The high strength formula of HIT RE 500 is
excellent for diamond cored and water filled holes.
HIT RE 500 has a longer working time making it ideal for
deep rebar embedment fastenings, smooth rebar doweling
applications and oversized drilled holes. HIT RE 500s
long working time compliments the fast curing Hilti HIT HY
150 which is ideal for threaded rod applications where
quick attachments save time and labor.
The HIT RE 500 dispenses as fast and easy as the HIT
HY 150 and its the only true epoxy (ASTM C881, Type
IV) on the market for fastening in base materials down to
23F (-5 C), thus making it an all weather product.
Reliable
Very high load values
Optimum working time in the extended temperature
range from 23 to 105F (-5 to +40C)
Suitable for use in holes drilled using diamond coring

equipment, rotary hammers, or pneumatic drills
Low sensitivity to oversized holes and wet holes
Red colored adhesive for easy on site inspection
Comprehensive technical software for effective
fastening designs
Convenient
Well proven, self-opening foil pack system saves time
especially in cold temperatures
Low dispensing force for quick and easy dispensing
saves time
Wide range of HIT dispensers for different job site
conditions
Long working time of 30 minutes, yet cures quickly in
approx. 12 hours at 68F (20C)
Reduced waste due to unique foil pack
Virtually odorless adhesive
ER-6010
COLA (City of Los Angeles)

RR-25514
NSF/ANSI Standard 61 for

potable water
Meets ASTM C 881-90 Type IV
requirements, most state D.O.T.s have
approved RE 500 for use on bridge
and pavement doweling applications
Package Volume
Volume of HIT Refill Pack is 20.2
in3, (330 mL), (11.1 oz)
Volume of HIT Jumbo Cartridge is
85.4 in3, (1400 mL), (47.3 oz)
Components
HIT-RE Mixer (Jumbo)
HIS Internally Threaded Insert
HAS Threaded Rod
Rebar (supplied by contractor)
Eye Bolt (supplied by contractor)
For secure fastening of reinforcing bars: Hilti HIT-RE 500
For fastening under water to 165 feet

(50 m)
The new
adhesive
provides
reliable
fastenings,
even when
holes are
drilled using
diamond
coring
equipment or
pneumatic
drills, wet or
oversized.
Convenient, fast dispensers for

different job site conditions (manual,
battery, pneumatic)
00340225
00373958
Description
Master
Carton
Item No
HIT RE 500
HIT RE 500 Jumbo
00369251
--
Refer to the
Hilti North
America Product
Technical Guide
Visit Hilti Online and
click on Tech Center
www.us.hilti.com
HIT Adhesives (11.1 fl oz/330 ml or jumbo 47.3 fl oz/1400 ml)
Cartridge
Item No
For complete
Hilti Anchoring
Systems
technical
information:
Contents
Master
Carton
Contents
Incuded in each Package
Dispensers see page:
1 Refill Pack
1 Jumbo
25
4
1 Mixer & 3/8" filler tube

1 Mixer
7.19
7.10
Heavy Duty Anchor
HIT HY 150 System:

Solid Base Material
104F (40C) down to 23F (-5C)
Listings
ER-5193
HIT-TZ: ER-5942
What It Does
How It Works
Volume of HIT Refill Pack is 20.2 in3,

(330 mL), (11.1 oz)
Volume of HIT Jumbo is 85.4 in3,
(1400 mL), (47.3 oz)
The HY 150 provides an economical method to anchor

into solid base materials such as concrete, grout, and
stone. Threaded rod, rebar, HIS internally threaded
inserts and eyebolts can be fastened into concrete and
diverse solid base materials such as cut stone and rock.
There are five basic components in the HIT HY 150
system:
HIT HY 150 adhesive
HIT dispenser
Fastener
Drill
Drill bit
Components
How HIT-TZ Works
HIT HY 150 is packaged in dual refill packs which keep

the resin and hardener components separate. The resin
and hardener are dispensed through a mixing tube,
which provides proper mixing and eliminates the
possibility of measuring errors. The dispenser has a dual
piston system to ensure accurate dispensing of the resin
and hardener. The mixed adhesive is injected directly
into the drilled hole in the solid base material.
The formulation of HIT HY 150 is based on a
revolutionary hybrid mortar. The organic component, a
urethane methacrylate resin, reacts with a hardener to
provide a fast, dependable reaction in a wide range of
temperatures. The inorganic component, Portland
Cement, reacts with water to provide a stable,
temperature resistant basis for the cured product. The
combination of these four components provides excellent
bond strength, stiffness, temperature resistance and a
rapid cure.

RR-25257

Report No. 9930
HIT-TZ: RR-25515
NSF/ANSI Standard 61 for

potable water
Package Volume
HIT-M Mixer (Small)

HIT-RE Mixer (Jumbo)
HAS Threaded Rod
When an axial load is applied the innovative HIT-TZ

threaded rod creates expansion forces which
supplement the bonding power of HIT HY 150 and the
concrete. This compensates for unfavorable hole
conditions, which means:
No more brushing and blowing
No need to remove water or dry holes
No need to Roughen diamond cored holes
HIT-TZ threaded rods provide the same published tensile
load performance as HAS-E rods with HIT HY 150 at
20% less embedment.
How It Holds
The HIT HY 150 system obtains holding values from
bonding and keying. The adhesive viscosity of HIT HY
150 permits use in horizontal anchoring and doweling
applications. The resin formulation allows HIT HY 150 to
cure in relatively short periods of time over a wide range
of temperatures while maintaining superior aging
stability and weathering resistance.
HIT-TZ
For complete
Hilti Anchoring
Systems
technical
information:
7.11
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
HIT Adhesives (11.1 fl oz/330 ml or large 37 fl oz/1100 ml)
Cartridge
Item No
Description
Master
Carton
Item No
Contents
Master
Carton
Contents
7.19
00371957
--
HIT HY 150
HIT HY 150 Jumbo
00332230
00373955
1 Refill Pack
Jumbo
25
4
1 Mixer & 3/8" filler tube

1 Mixer
Cold / Specialty Anchor
HIT-ICE System: Solid Base Material

The New Power of Injection
NEW!
down to -10F (-23C)
Package Volume
Volume of HIT-ICE cartridge 18.1 in3,
(297 mL), (10 oz)
Hilti HIT-ICE presents a solution for the difficult problems

when fastening in a solid base material from the extreme
cold temperatures of winter to the hot days of summer.
Its wide application temperature range and fast cure
compliment the Hilti HIT system to provide a HIT for all
seasons.
For colder environment installations, HIT-ICE adhesive is
a formulation for solid base material temperatures down
to -10F (-23C) ideal for all threaded rod and rebar
applications. For warmer environment installations,
HIT-ICE keeps you moving with a quick cure perfect for
stone, masonry and non-structural crack filling. When
used with the HIT-TZ rod, HIT-ICE provides optimum
versatility and performance in the most unfavorable
conditions.
HIT-ICE consists of a methacrylate resin and hardener in
a single hard cartridge container. Fast and easy
dispensing in temperature from -10F to 90F (-23C to

32C) makes HIT-ICE the best combination of low
application temperature and performance.
High load fastenings in extreme cold temperatures
Fast cure times
For use with HIT-TZ rods
Good handling due to low dispensing forces
Threaded rod applications
Non-structural crack filler
Stone masonry
Rebar doweling
Easy clean up
Components
HIT-MZ Mixer (Small)
HAS Threaded Rod
HIT-TZ
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Specification Table
see page:
HIT ICE (10 fl oz/297 ml)
Single
Cartridge
Item No
00371292
Description
Master
Carton
Item No
Contents
Master Incuded in
Carton each
Contents Package
HIT ICE
00372705
1 Cartridge
24
1 Mixer
7.13
7.19
7.12
Heavy Duty / Specialty Anchors

Specification Table HIT HY 150 / HIT-ICE
Fastener
HAS-E,
HAS Super
or
HAS SS Rods3
HIT-TZ9,10
Threaded
Rods
HIS or HIS-R
Internally
Threaded
Inserts5
Rebar1, 2
Anchor
Diameter/
Rebar Size
Std
Embed
3/8"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4
3/8"
1/2"
5/8"
3/4"
3/8"
1/2"
5/8"
3/4"
#3
#4
#5
#6
#7
#8
#9
#10
#11
3-1/2"
4-1/4"
5"
6-5/8"
7-1/2"
8-1/4"
12
2-5/8"
3-1/2"
4"
5-1/4"
4-1/4"
5"
6-5/8"
8-1/4"
3-1/2"
4
5"
7"
7-1/2"
8"
10"
12"
14"
Recommended
(Item No.) Hilti Drill Bits8
Approximate No. Fastenings/Cartridge7

HY 150
Small
Jumbo
HIT-ICE
(00205339) TE-C+ 7/16 x 6"

(00028041) TE-C+ 9/16 x 12"
(00028047) TE-C+ 11/16 x 12"
(00028621) TE-C-S 13/16 x 18"
(00028720 TE-Y 24mm x 32cm
(00340707) TE-YX 1-1/16 x 21"
(00340718) TE-YX 1-1/2 x 23
(00205339) TE-C+ 7/16 x 6"
(00028041) TE-C+ 9/16 x 12"
(00028047) TE-C+ 11/16 x 12"
(00028621) TE-C-S 13/16" x 18"
(00028047) TE-C+ 11/16 x 12"
(00028624) TE-C+ 7/8 x 10"
(00340708) TE-YX 1-1/8 x 15"
(00340711) TE-Y 1-1/4" x 15"
(00205352) TE-CX 1/2 x 6"
(00028043) TE-C+ 5/8 x 8"
(00028618) TE-C-S 3/4 x 8"
(00028624) TE-C-S 7/8 x 10"
(00340704) TE-YX 1 x 13"
(00340708) TE-YX 1-1/8 x 15"
(00340715) TE-YX 1-3/8 x 23"
(00340718) TE-YX 1-1/2 x 23"
(00220611) TE-YGB 1-3/4 x 23"
50
31
18
10
9
6
1
58
44
21
12
37
23
8
6
62
31
19
11
9
7
3
2
1
248
154
90
50
45
30
5
288
218
104
60
184
114
40
30
308
154
94
55
45
35
15
10
6
46
28
17
9
8
6
1
53
40
19
11
34
21
7
6
57
28
17
10
8
7
3
2
1
Bond Strength
in 4000 psi Concrete4
Tension (lb)
Steel Strength
HAS Super
Tension (lb)
Shear (lb)
For Allowable &

Ultimate Load Values,
refer to the
Hilti North American
Technical Guide,
2002 Ed.,
Section 4.2.2
Click here for product load values.
* For HIT Volume Charts, see Hilti Product Tech Guide, 2002 Ed. section 4.22 (p. 97).
1 Drill bit diameter may vary due to rebar tolerances. Use smallest practical drill bit for each size
rebar.
2 Refer to Hilti Product Technical Guide or contact Technical Service Specialist for embedments to
develop ultimate tensile capacities of rebar, and additional technical information.
3 Compare allowable bond strength to allowable tensile strength of appropriate threaded rod in the
Hilti Product Technical Guide, use lowest value.
4 Refer to Hilti Product Technical Guide for load tables in various base materials and ultimate load tables.
5
6
7
8
Ultimate steel strength values based on AISC values for A325 Bolts (fy = 92 ksi, fu = 120 ksi).
Not recommended.
Assumes no waste.
Use carbide bits. For use of diamond core bits, contact Hilti. HIT-TZ can be used with Hilti matched
tolerance Diamond Core Bits.
9 HIT-TZ steel strength values based on ASTM A510 or AISI 316.
10 HIT-TZ must be installed at temperature >40F with HIT HY-150.
Specification Table HIT RE 500

Fastener
HAS-E,
HAS Super
or
HAS SS Rods3
HIS or HIS-R
Internally
Threaded
Inserts5
Rebar1, 2
Anchor
Diameter/
Rebar Size
Std
Embed
3/8
1/2
5/8
3/4
7/8
1
1-1/4
3/8
1/2
5/8
3/4
#3
#4
#5
#6
#7
#8
#9
#10
#11
3-3/8
4-1/2
5-5/8
6-3/4
7-7/8
9
11-1/4
4-1/4
5
6-5/8
8-1/4
3-3/8
4-1/2
5-5/8
6-3/4
7-7/8
9
10-1/8
11-1/4
12-3/8
Recommended
(Item No.) Hilti Drill Bits8
Approximate No
Fastenings/Cartridge7
Small
Jumbo
(00028032) TE-C+ 7/16 x 6"

(00028041) TE-C+ 9/16 x 12"
(00028618) TE-C+ 3/4 x 8"
(00028624) TE-C+ 7/8 x 10"
(00340704) TE-YX 1 x 13"
(00340708) TE-YX 1 1/8 x 15"
(00340715) TE-YX 1 3/8 x 23"
(00028047) TE-C+ 11/16 x 12"
(00028624) TE-C+ 7/8 x 10"
(00340708) TE-YX 1 1/8 x 15"
(00340711) TE-YX 1 1/4 x 15"
(00205352) TE-CX 1/2 x 6"
(00028043) TE-C+ 5/8 x 8"
(00028618) TE-C+ 3/4 x 8"
(00028624) TE-C+ 7/8 x 10"
(00340704) TE-YX 1 x 13"
(00340708) TE-YX 1 1/8 x 15"
(00340715) TE-YX 1 3/8 x 23"
(00340718) TE-YX 1 1/2 x 23"
(00220611) TE-YGB 1 3/4 x 23"
52
28
11
7
5
4
2
27
16
6
4
44
25
16
11
8
6
3
2
1
* For HIT Volume Charts, see Hilti Product Tech Guide, 2002 Ed. section 4.2.4 RE 500 (p. 122).
1 Drill bit diameter may vary due to rebar tolerances. Use smallest practical drill bit for each size
rebar.
2 Refer to Hilti Product Technical Guide or contact Technical Service Specialist for embedments to
develop ultimate tensile capacities of rebar, and additional technical information.
www.us.hilti.com
for product information
for setting instructions,
7.13
255
137
56
37
27
19
12
168
105
38
27
221
125
83
56
41
31
14
11
7
Bond Strength
Tension (lb)
Click
Steel Strength
HAS Super
Tension (lb)
Shear (lb)
For Allowable &

Ultimate Load Values,
refer to the
Technical Guide,
here for
product
load
2002 Ed.,
Section 4.2.4
values.
3 Compare allowable bond strength to allowable tensile strength of appropriate threaded rod in the
Hilti Product Technical Guide, use lowest value.
4 Refer to Hilti Product Technical Guide for load tables in various base materials and ultimate load
tables.
5 Ultimate steel strength values based on AISC values for A325 Bolts (fy = 92 ksi, fu = 120 ksi).
6 Not recommended.
7 Assumes no waste.
8 Use carbide bits. For use of diamond core bits, contact Hilti. HIT-TZ can be used with Hilti
matched tolerance Diamond Core Bits.
Heavy Duty / Specialty Anchors
bronze medal
Winner 2001
Hilti HIT-TZ Threaded Rod

Threaded Rod
Diameter
(in.)
Drill Bit
Diameter
(in.)
Depth of
Embedment
(in.)
Maximum
Fastening
Thickness (in.)
Overall
Length
(in.)
Quantity
per Box
Item No.
HIT-TZ ISO 5.8
Carbon Steel
Item No.
HIT-RTZ 316
Stainless Steel
Description
3/8
1/2
5/8
3/4
7/16
9/16
11/16
13/16
2-7/8
3-1/2
4
5-1/4
1
1-1/2
2-1/4
2-1/4
4-1/2
5-11/16
7-1/16
8-9/16
40
24
16
8
00337484
00337485
00337486
00337487
00337498
00337499
00337500
00337501
HIT-TZ
HIT-TZ
HIT-TZ
HIT-TZ
3/8x2-7/8/1
1/2x3-1/2/1-1/2
5/8x4/2-1/4
3/4x5-1/4/2-1/4
Threaded Rods
Item No.
(Box)
00333184
00333185
00333183
00333186
00333187
00333188
00333189
00333190
00333191
00333192
HAS-E Rods 5.8

Master
Carton
(MC)
Description
00338933
00338934
00338932
00338935
00338936
00338937
00338938
00338939
00338940
00338941
HAS Super A193, B7 High Strength Rods

Qty
Box/MC
3/8x3
3/8x4-3/8
3/8x5-1/8
3/8-8
3/8x12
1/2x3-1/8
1/2x4-1/2
1/2x6-1/2
1/2x8
1/2x10
10/360
10/180
20/240
10/160
10/90
10/240
10/160
20/160
10/120
10/120
00333193 00338942
00333194 00338943
1/2x12
5/8x8
10/80
20/80
00333197
00333195
00333196
00333201
00333198
00333202
00333203
00338946
00338944
00338945
00338947
00338948
00338949
00338950
5/8x9
5/8x12
5/8x17
3/4x10
3/4x11
3/4x12
3/4x14
10/60
10/60
10/40
10/40
10/30
10/30
10/30
00333204
00333205
00333206
00333207
00333208
00338951
00338952
00338953
00338954
00338955
3/4x17
3/4x19
3/4x21
3/4x25
7/8x10
10/20
10/20
10/20
10/20
10/20
00333209
00333210
00333211
00333212
00333213
00333214
00333215
00338956
00338957
00338958
00338959
00338960
00338961
00338962
7/8x13
1x12
1x14
1x16
1x20
1-1/4x16
1-1/4x22
10/20
4/16
2/16
2/12
2/12
4/8
2/8
HAS-R Rods 304 Stainless Steel
HAS-R Rods 316 Stainless Steel
Item No.
Description
Qty
Box
Item No.
Description
Qty
Box
00068657
3/8x5-1/8
10
00068675
3/8x5-1/8
10
96803000 3/8x5-1/8
00068658
1/2x6-1/2
10
00068676
96802000
96802001
1/2x6-1/2
1/2x8
1/2x10
10
1
1
96803001 1/2x6-1/2
96803003
00333783
5/8x7-5/8
10
00333782
96802002
5/8x7-5/8
5/8x10
10
1
00068660
3/4x9-5/8
00068678
3/4x9-5/8
96901822
3/4 x 14
96802003
96802004
96802005
3/4x12
3/4x14
3/4x16
1
1
1
96802006
7/8x10
96802007
1x12
00068661 7/8x10 (HDG)

96901815
7/8x11
96901816 7/8x12 (HDG)
00045259 7/8x16 (HDG)
00068662
1x12
96901818
1x14
96901819
1x16
96901820
1x21
00333779
1-1/4x16
5
5
5
5
5
5
5
5
4
96901821
1-1/4x23
Item No.
Description
1/2x11
Qty
Box
00333781 5/8x7-5/8
10
96803004
96803005
1
1
5/8x9
5/8x12
96803006 3/4x9-5/8
96803007
1x12
4/16
HIS Carbon Steel and HIS-R 316 Stainless Steel Internally Threaded Inserts
HIS
Item No.
00258029
00258030
00258031
00258032
HIS-R
Item No.
00258029
00258030
00258031
00258032
Description
Useable
Thread
Length (in.)
Qty
Box
3/8x4-1/4
1/2x5
5/8x6-5/8
3/4x8-1/4
1
1-3/16
1-1/2
2
10
5
5
5
www.us.hilti.com
7.14
Hollow Base Anchor
HIT HY 20 System:
Masonry Construction With Voids
104F (40C) down to 23F (-5C)
Approvals

ER-4815 for URM

RR-24564 for URM

Report No. 9930
Package Volume
Volume of HY 20 Refill Pack is
20.2 in3, (330 mL), (11.1 oz)
Volume of HY 20 Jumbo is 85.4 in3,
(1400 mL), (47.3 oz)
Components
HIT-M Mixer (Small)
Screen Tube
RE-M Mixer (Jumbo)
Bent Anchor Rod with Nut and Washer

(URM)or HAS-E Rod with Beveled Washer
HAS-E Rod with Nut and Washer
What It Does
The Hilti HIT HY 20 system represents a unique solution
to the difficult problem of fastening thru masonry
construction where the quality of brick and mortar is
inconsistent, and where voids may be present between
wythes of brick walls.
The HIT HY 20 application is ideally suited to solving
multi wythe problems in renovation and seismic upgrade
of URM (unreinforced masonry) buildings.
There are six basic components in the HIT HY 20
system:
HY 20 Adhesive HAS threaded anchor rod or rebar
HIT dispenser
Drill
HIT screen tube Drill bit
How It Works
The Hilti HIT HY 20 is packaged in dual refill packs which
keep separate the resin and hardener components of the
adhesive. The resin and hardener are dispensed through
a mixing tube, providing uniform quality. The screen tube
is a key part of this system. It is filled with adhesive
outside the hole, so the correct quantity of adhesive is

used each time. The screen tube is then inserted into the
hole and the anchor rod is pushed into the adhesive
filled screen, displacing the adhesive into the wall.
The formulation of the HY 20 is based on a revolutionary
hybrid mortar. The hybrid refers to the combination of
organic and inorganic components. The organic
component is a urethane methylcrylate resin which
reacts with a hardener to provide a fast, dependable
reaction in a wide range of temperatures. The organic
component is Portland Cement which reacts with the
water to provide a stable, temperature resistant basis for
the cured product.
How It Holds
The HIT HY 20 system obtains holding values from
bonding and keying. Where the wall is solid, the adhesive
bonds itself to the masonry. Where voids exist, the
adhesive fills the voids with an adhesive plug keying
itself into masonry. This outstanding feature allows the
HIT HY 20 system to function in poor quality base
material, even when the size and location of voids are
unknown.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Specification Table
see page:
7.16
7.19
HIT Adhesives (11.1 fl oz/330 ml or large 47.3 fl oz/1400 ml)
Single
Cartridge
Item No.
00371959
--
Description
Master
Carton
Item No.
HIT HY 20
HIT HY 20 Jumbo
00332229
00373957
Contents
Master
Carton
Contents
1 Refill Pack
Jumbo
25
4
1 Mixer with extension

1 Mixer
7.15
Hollow Base Anchor
HIT HY 20 System: Masonry Construction With Voids

Specification Table
HAS-E Anchor
Rod Size
Screen
Tube Size
Hole
Depth
3/8" x 8"
3/8" x 12"
1/2" x 8"
1/2" x 12"
5/8" x 8"
5/8" x 12"
3/4" x 10"
3/4" x 17"
3/8" x 6"
3/8" x 10
1/2" x 6
1/2" x 10
5/8" x 6
5/8" x 10
3/4" x 8"
3/4" x 13"
6-1/4"
10-1/4"
6-1/4"
10-1/4"
6-1/4"
10-1/4"
8-1/4"
13-1/4"
Recommended
Hilti Drill Bit
Item No.
00205354
00205355
00028047
00028048
00220644
00220645
00220650
00220650
TE-C 1/2"-12"
TE-C 1/2"-18"
TE-C + 11/16"-12"
TE-C + 11/16"-18"
TE-YX 27/32"-13"
TE-YX 27/32"-21"
TE-YX 1"-21"
TE-YX 1"-21"
Approx. Fastenings
per Cartridge2
Small
Jumbo
15
9
8
4
5
3
3
1.5
70
43
38
19
24
13
13
7
Allowable Load Values

for Multi-Wythe Brick Walls1
Tension (lb)
Shear (lb)
685
815
745
1270
815
1285
1400
2100
590
590
930
930
1355
1355
1800
1800
1 Values represent test results based on mortar shear strength of 45 PSI or greater. Based on a safety factor of 5.
2 Volume of HIT refill pack is 20.2 in3 (11.1 oz), (330 mL) Volume of HIT Large Cartridge is 67.2 in3, (37 oz), (1100 mL). Assumes no waste.
Threaded Rods (Stainless Steel Rods are also available. Contact Customer Service for information.)
Item No.
Description
00333186
00333187
00333191
00333193
00333194
00333195
00333196
00333201
00333202
00333203
00333204
00333205
00333206
00333207
HAS-E 3/8 x 8 with Nut and Washer

Use with Screen Size
Qty/Pkg
Master
Carton (MC)
Qty/MC
3/8" x 6"
3/8" x 10"
1/2" x 6"
1/2" x 10"
5/8" x 6"
5/8" x 10"
5/8" x 10"
3/4" x 8"
3/4" x 8"
3/4" x 8"
3/4" x 13"
3/4" x 17"
3/4" x 17"
3/4" x 21"
10
10
10
10
20
10
10
10
10
10
10
10
10
10
00338935
00338936
00338940
00338942
00338943
00338944
00338945
00338947
00338949
00338950
00338951
00338952
00338953
00338954
160
90
120
80
80
60
40
40
30
30
20
20
20
20
Screen Tubes (Stainless Steel HIT Screens are also available. Contact Customer Service for information.)
Item No.
Description
00020953
00020954
00020955
00020956
00063930
00063931
00020836
00020837
00020838
00020839
Screen Tube 3/8 x 6

Screen Tube 3/8 x 10
Screen Tube 1/2 x 6
Screen Tube 5/8 x 6
Screen Tube 3/4 x 8
Filler Tubes
Included in Package
Hole/Bit
Diameter
Use with Anchor

Rod Diameter
Qty/Pkg
3/8" x 8" (2)

3/8" x 8" (2)
1/2" x 4-1/2" (2)
1/2" x 9-1/2" (2)
1/2" x 4-1/2" (2)
1/2" x 9-1/2" (2)
1/2" x 4-1/2" (2)
1/2" x 9-1/2" (2)
1/2" x 13-1/2" (2)
1/2" x 17-1/2" (2)
1/2"
1/2"
11/16"
11/16"
27/32"
27/32"
1"
1"
1"
1"
3/8"
3/8"
1/2"
1/2"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
10
10
10
10
10
10
10
10
10
10
Accessories
Item No.
Description
00065797
Beveled Washer
Qty/Pkg
10
Use with 3/4" diameter threaded rod in seismic upgrade of URM buildings for
22.5 shear/tension anchor. Bevel washer eliminates the use of bent threaded rods.
00020951
HIT Rod 3/4 x 19 Bent
10
00027535
Plate Washer for 5/8" diameter rod (6" x 6" x 3/8")
10
www.us.hilti.com
7.16
Hollow Base Anchor
HIT HY 20 System:
Hollow Block, Hollow Clay Tile & Brick with Holes
104F (40C) down to 23F (-5C)
Approvals

Report No. 9930
Package Volume
Volume of HIT HY 20 Refill Pack is
20.2 in3, (330 mL), (11.1 oz)
Volume of HIT HY 20 Jumbo is 85.4
in3, (1400 mL), (47.3 oz)
Components
HAS Threaded Rod
What It Does
The Hilti HIT HY 20 system excels in its capability to
solve many fastening problems in masonry construction
with voids. HY 20 is the ideal solution for fastenings to
hollow block, hollow clay tile, and brick with holes.
There are six basic components in the HIT HY 20
system:
HIT HY 20 Adhesive
Drill
HIT dispenser
Drill bit
HIT-S screen tube
HIT threaded anchor rod or insert
How It Works
HIS Setting Tool
Square Drive Shaft
Drive Socket
The Hilti HIT HY 20 is packaged in dual refill packs which

keep separate the resin and hardener components of the
adhesive. The resin and hardener are dispensed through a
mixing tube, providing uniform quality. The screen tube is
a key part of this system. It is inserted into the hole and
then filled with adhesive with the extension attached to the

mixer. The anchor rod is then pushed into the adhesive
filled screen, displacing the adhesive into the wall.
The formulation of the HY 20 is based on a revolutionary
hybrid mortar. The hybrid refers to the combination of
organic and inorganic components. The organic
component is a urethane methylcrylate resin which reacts
with a hardener to provide a fast, dependable reaction in
a wide range of temperatures. The organic component is
Portland Cement which reacts with the water to provide a
stable, temperature resistant basis for the cured product.
How It Holds
The HIT HY 20 system obtains holding values from bonding
and keying. Where the wall is solid, the adhesive bonds
itself to the masonry. Where voids exist, the adhesive fills
the voids with an adhesive plug keying itself into masonry.
This outstanding feature allows the HIT HY 20 system to
function in poor quality base material, even when the size
and location of voids are unknown.
Rebar Adapter
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Specification Table
see page:
7.18
7.19
7.17
HIT Adhesives (11.1 fl oz/330 ml or large 47.3 fl oz/1400 ml)
Single
Cartridge
Item No.
Description
Master
Carton
Item No.
Contents
Master
Carton
Contents
00371959
--
HIT HY 20
HIT HY 20 Jumbo
00332229
00373957
1 Refill Pack
Jumbo
25
6
1 Mixer with extension

1 Mixer
Hollow Base Anchor
HIT HY 20 System:
Hollow Block, Hollow Clay Tile & Brick with Holes
Specification Table
Anchor
System
HIT-A
Standard
and
HIT-A
Short
Anchor
Rods
HIT-I
Standard
and
HIT-I
Short
Internally
Threaded
Inserts
Base
Material
HIT Rod-A/Insert-I
Item No.
(10 pcs/Pkg)
HIT-S Screen Tube

Item No.
(10 pcs/Pkg)
HIT-A Rod 1/4 x 2-1/2

HIT Combi-S12/A
00078739
00049765 2" long
Brick
HIT-A Rod 5/16 x 4
HIT-S-16
with
00088977
00068613 3-3/8" long
Holes
HIT-A Rod 3/8 x 4-3/8
HIT-S-16
00088978
00068613 3-3/8" long
HIT-A Rod 1/2 x 4-1/2
HIT-S-16
00088979
00068613 3-3/8" long
HIT-A Rod 1/4 x 2-1/2
HIT Combi-S12/A
00078739
00049765 2" long
Hollow Block
HIT S-16/2
Lightweight HIT-A Rod 5/16 x 2-1/2
00088392
00077810
2" long
or
HIT-A Rod 3/8 x 3
HIT S-16/2
Normal
00088393
00077810 2" long
Weight
HIT-A Rod 1/2 x 3-1/8
HIT S-16/2
00088394
00077810 2" long
HIT-A Rod 1/4 x 2-1/2
HIT Combi-S12/A
00078739
00049765 2" long
HIT-A Rod 5/16 x 2-1/2
HIT S-16/2
00088392
00077810
2" long
Clay Tile
HIT-A Rod 3/8 x 3
HIT S-16/2
00088393
00077810 2" long
HIT-A Rod 1/2 x 3-1/8
HIT S-16/2
00088394
00077810 2" long
Screen Tube with Insert Combi-S12/I (for #14 screw)
00049766 2" long
Brick
HIT-I Insert 5/16 x 3-3/16
HIT-S-16
with
00088996
00068613 3-3/8" long
HIT-S-22
Holes
00088997
00068615 3-3/8" long
HIT-S-22
00088998
00068615 3-3/8" long
00049766 2" long
Hollow Block
HIT-I Insert 5/16 x 2
HIT-S-16/2
Lightweight
00088397
00077810 2" long
or
HIT-S-22/2
Normal
00088398
00077811 2" long
Weight
HIT-S-22/2
00088399
00077811 2" long
00049766 2" long
HIT-S-16/2
Clay Tile
00088397
00077810 2" long
HIT-S-22/2
00088398
00077811 2" long
HIT-S-22/2
00088399
00077811 2" long
Recommended
Hilti Bit
TE-CX 1/2 - 6
00205352
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-CX 1/2 - 6
00205352
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-CX 1/2 - 6
00205352
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-C+ 5/8 - 8
00028043
TE-C+ 1/2 - 6
00205352
TE-C+ 5/8 - 8
00028043
TE-C-S 27/32-12
00028623
TE-C-S 27/32-12
00028623
TE-CX 1/2 - 6
00205352
TE-C+ 5/8 - 8
00028043
TE-C-S 27/32-12
00028623
TE-C-S 27/32-12
00028623
TE-CX 1/2 - 6
000205352
TE-C+ 5/8 - 8
00028043
TE-C-S 27/32-12
00028623
TE-C-S 27/32-12
0028623
Approx.1
Fastenings
Sm Cartridge
Approx.1
Fastenings
Jumbo
38
189
365
305
43
565
530
43
775
930
43
775
1375
38
189
255
340
13
58
370
505
13
58
525
790
13
58
525
1230
38
189
130
100
13
58
150
220
13
58
150
220
13
58
150
500
38
189
300
530
43
585
750
43
1160
1380
43
1160
1635
38
189
240
510
13
58
400
780
13
58
400
1425
13
58
400
1800
38
189
85
150
13
58
175
220
13
58
185
435
13
58
185
500
Allowable
Working Values2 (lb)
Tension
Shear
1 Volume of HIT refill pack is 20.2 in 3, (11.1 oz), (330 mL) Volume of HIT Large Cartridge is 67.2 in 3, (37 oz), (1100 mL). Assumes no waste.
2 Due to wide strength variations encountered in masonry, these values should be considered to be guide values. Based on a safety factor of 6 for tension, safety factor of 4 for shear.
www.us.hilti.com
7.18
Dispensers / Hole Cleaning
Dispensers
Battery Powered
Item No.
Ordering designation
00335288
BD2000 Battery Dispenser Kit
Includes: BD2000 battery dispenser, 2 foil pack holders, battery, charger, blow-out pump and
3 cleaning brushes. Packed in the BD2000 toolbox.
00332117
BD2000 Battery Dispenser only
Manual
Item No.
00371291
00229154
00229170
MD 1000 Manual Dispenser for HIT ICE

MD 2000 dispenser includes foil pack holder
Foil pack holder 3:1 spare
Hilti HIT Dispenser
with 1/4" female compressed air coupling

Item No.
00255032
00373959
00373960
HIT-P3000F dispenser (for foil packs)

HIT-P8000D pneumatic dispenser (for jumbo cartridges)
Jumbo pack holder replacement for P8000D
Mixers and Filler Tubes
Item No.
Qty/pkg
00068071
HIT-ME, Mixer with extension
HY 20 Mixer with extension for S16, S16/2, S22, S22/2 screen tubes
00068156
HIT-M static mixer for HY foil packs
For use with small HIT HY 150 and HY 20 refill packs
00371290
HIT-M2 static mixer for HIT ICE
00337111
HIT-RE-M static mixer (suitable for foil pack and jumbo cartridges)
00063799
Filler Tube 3/8" x 8"
HIT-M Mixer (Small)
HIT-RE-M Mixer
Attach filler tube to small mixer to fill deeper holes & 3/8" diameter screen tubes
00063993
Filler Tube 1/2" x 11 1/2
00063995
Filler Tube 1/2"x 17 1/2"
HIT Filler Tube
Attach filler tube to large mixer to fill deeper holes & 1/2" and larger diameter screen tubes.
Attach filler tube to large mixer to fill deeper holes & 1/2" and larger diameter screen tubes.
Hole Cleaning Accessories

Nylon Brushes are required for all applications in brick or softer masonry.
Wire brushes are required for all applications using HY 150 Adhesive.
HIT RE 500 can be used with nylon or wire brushes.
Item No.
Description
Qty/pkg
00063964
Air Nozzle (Length 24")
00060579
Blow Out Pump
For Use with HY 20 or RE 500
1
1
Item No.
Description
Hole Diameter
Qty/pkg
00063855
00063856
00063857
00063963
Nylon Brush 5/8" x 12"

Nylon Brush 7/8" x 12"
Nylon Brush 1" x 12"
Nylon Brush 1-1/4" x 29"
3/8" to 1/2"
1/2" to 5/8"
5/8" to 3/4"
> 3/4"
1
1
1
1
For Use with HY150 or RE 500
7.19
Item No.
Description
Hole Diameter
Qty/pkg
00255781
00255782
00059893
00255783
00255784
00003206
Wire Brush 3/8" x 8"

Wire Brush 5/8" x 5/8"
Wire Brush 1" x 18"
Flat Wire Brush
7/16" to 1/2"
9/16" to 5/8"
11/16" to 3/4"
13/16" to 15/16"
1" to 1-1/8"
> 1-1/8" holes
1
1
1
1
1
1
Heavy Duty Anchor

Listings
The Hilti HVA Adhesive Anchor System
ICBO (International Conference of

Building Officials)
ER-5369
Bringing Anchor Technology To A New Standard

Report No. 9930

RR-25363
NSF/ANSI STD 61 certification

for potable water
Formulated for easy installation in freezing temperatures

without preheating capsules for all weather installation
Virtually odor free: allows continuous work in
confined areas
Contains no hazardous chemicals for worker safety
as well as easy storage and transportation
No expansion forces on concrete allows use in
applications with small edge distance and/or anchor
spacing
Durable plastic capsule packaging
Flexible plastic capsules allow use in irregular holes
resulting from rebar hits during the drilling process
High load values for threaded rod and rebar
applications allows use in a broad range of applications
Fast curing for high productivity and quick bolt-ups
Advantages
No hole brushing required, just blow out hole with
compressed air makes installation fast and easy
Arrowhead-shaped capsule stays in the hole for easy
overhead installation
HVU aggregate roughens hole which allows use in
Hilti matched tolerance diamond-cored holes
ICBO AC 58, ASTM E 1512 testing for use in seismic
applications
NSF/ANSI Standard 61 approval allows use in
potable water
HVU combined with HIT HY 150 allows use in
underwater installations
ICBO AC 58, ASTM E 1512 testing allows use in
damp holes
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Square Drive Shaft
HAS Threaded Rod
Drive Socket
HIS Internally Threaded

Insert
HIS Setting Tool

Rebar Adapter
Specification Table
HVU
HAS-E/HIS/Rebar
Hole
Diameter
Embed
Depth
Max Thkns
of Object
Fastened1
Hilti Drill
(Item No.) Hilti Drill Bit3
3/8 x 3-1/2
1/2 x 4-1/4
5/8 x 5
3/4 x 6-5/8
7/8 x 6-5/8
1 x 8-1/4
1-1/4 x 12
1/2 x 4-1/4
5/8 x 5
7/8 x 6-5/8
1 x 8-1/4
1/2 x 4-1/4
5/8 x 5
7/8 x 6-5/8
1 x 8-1/4
1 x 8-1/4 & 5/8 x 5
HAS-E 3/8 x 5-1/8

HAS-E 1/2 x 6-1/2
HAS-E 5/8 x 8
HAS-E 3/4 x 10
HAS-E 7/8 x 10
HAS-E 1 x 12
HAS-E 1-1/4 x 16
HIS 3/8 x 4-1/4
HIS 1/2 x 5
HIS 5/8 x 6-5/8
HIS 3/4 x 8-1/4
Rebar #4
Rebar #5
Rebar #6
Rebar #7
Rebar #8
7/16"
9/16"
11/16"
7/8"
1"
1-1/8"
37mm
11/16"
7/8"
1-1/8"
1-1/4"
5/8"
13/16"
1"
1-1/8"
1-1/4"
3-1/2"
4-1/4"
5"
6-5/8"
6-5/8"
8-1/4"
12"
4-1/4"
5"
6-5/8"
8-1/4"
4-1/4"
5"
6-5/8"
6-5/8"
8-1/4"
1"
1-1/2"
1-3/4"
2"
2-1/4"
2-1/2"
2-3/4"
-
TE 5/15
TE 18/25
TE 18/25
TE 55/76
TE 55/76
TE 76
TE 76
TE 5/25
TE 18/25
TE 55/76
TE 55/76
TE 55/76
TE 55/76
TE 75
TE 75
TE 75
(00205340) TE-CX 7/16-18

(00028041) TE-C+ 9/16-12
(00028047) TE-C+ 11/16-12
(00340701) TE-YX 7/8-13
(00340704) TE-YX 1-13
(00340708) TE-YX 1-1/8-15
(00339039) TE-YX 37-92
(00028047) TE-C+ 11/16-12
(00028624) TE-C-S 7/8-10
(00220653) TE-C-S 1-1/8-17
(00340711) TE-YX 1-1/4-15
(00220636) TE-YX 5/8-13
(00340698) TE-YX 13/16-21
(00340704) TE-YX 1-13
(00340708) TE-YX 1-1/8-15
(00340711) TE-YX 1-1/4-15
Recommended
Tightening
Torque (ft-lb)
Wrench
Size2
18
30
75
150
175
235
400
18
30
75
150
-
9/16"
3/4"
15/16"
1-1/8"
1-7/16"
1-1/2"
1-7/8"
-
1 Based on standard HAS Rod sizes, special length HAS rods available.
2 Based on use with setting nuts.
3 Rebar diameters can vary. Use smallest practical bit for each size rebar.
7.20
Heavy Duty Anchor
HVU Adhesive Capsules, Carbon Steel HAS-E and HAS Rods / Stainless Steel HAS Rods
HAS-E/
HVU Adhesive Capsules
HVU Qty
Product
Item No.
Per Box
3/8" x 3-1/2"
3/8" x 3-1/2"
1/2" x 4-1/4"
1/2" x 4-1/4"
1/2" x 4-1/4"
5/8" x 5"
5/8" x 5"
5/8" x 5"
3/4" x 6-5/8"
3/4" x 6-5/8"
3/4" x 6-5/8"
3/4" x 6-5/8"
7/8" x 6-5/8"
7/8" x 6-5/8"
7/8" x 6-5/8"
1" x 8-1/4"
1" x 8-1/4"
1" x 8-1/4"
1" x 8-1/4"
1-1/4" x 12"
1-1/4" x 12"
00256692
10
00256693
10
00256694
10
00256702
00256695
00256696
00256699
HAS-E Rods 5.82

Product
HAS Super A193 B72
Item No.
Product
3/8" x 5-1/8" 00333183

3/8" x 8" 00333186
1/2" x 6-1/2" 00333190
1/2" x 8" 00333191
1/2" x 10" 00333192
5/8" x 8" 00333194
5/8" x 9" 00333197
5/8" x 12" 00333195
3/4" x 10" 00333201
3/4" x 11" 00333198
3/4" x 12" 00333202
3/4" x 14" 00333203
7/8" x 10" 00333208
7/8" x 13" 00333209
1" x 12"
1" x 14"
1" x 16"
1" x 20"
1-1/4" x 16"
1-1/4" x 22"
00333210
00333211
00333212
00333213
00333214
00333215
Item No.
HAS Rods 304 SS2

Product
HAS Rods 316 SS2
Item No.
Product
Item No.
HAS Qty
Per Box
3/8" x 5-1/8" 00068657 3/8" x 5-1/8" 00068675 3/8" x 5-1/8" 96803000 20/10
10
1/2" x 6-1/2" 00068658 1/2" x 6-1/2" 00068676 1/2" x 6-1/2" 96803001 20/10
1/2" x 8" 96802000
10
1/2" x 10" 96802001 1/2" x 11" 96803004 10
5/8" x 7-5/8" 00333783 5/8" x 7-5/8" 00333782 5/8" x 7-5/8" 00333781 20/10
5/8" x 10" 96802002 5/8" x 12" 96803004 10
5/8" x 9-5/8" 96803005 10
3/4" x 9-5/8" 00068660 3/4" x 9-5/8" 00068678 3/4" x 9-5/8" 96803006 10/5
10
3/4" x 12" 96802003
10
3/4" x 14" 96901822 3/4" x 14" 96802004
10
7/8" x 10" hdg1 00068661 7/8" x 10" 96802006
10/5
7/8" x 12" hdg1 96901816
10/5
7/8" x 16" hdg1 00045259
5
1" x 12"
00068662 1" x 12"
96802007 1" x 12"
96803007 4/5
1" x 14"
96901818
2/5
1" x 16"
96901819
2/5
1" x 21"
96901820
2/5
1-1/4" x 16" 00333779
4/4
1-1/4" x 23" 96901821
2/4
1 Hot-Dip Galvanized
2 Requires setting nuts.
HVU Adhesive Capsules, Carbon Steel HAS-E Combos and Master Cartons (MC)
HAS-E1
Qty
Product
Item No.
MC Item No.
Per Box/MC
Product
Item No.
Item No.
Qty
MC Item No.
Box/MC
3/8" x 3-1/2"
3/8" x 3-1/2"
1/2" x 4-1/4"
1/2" x 4-1/4"
1/2" x 4-1/4"
5/8" x 5"
5/8" x 5"
3/4" x 6-5/8"
3/4" x 6-5/8"
3/4" x 6-5/8"
7/8" x 6-5/8"
7/8" x 6-5/8"
1" x 8-1/4"
1" x 8-1/4"
1-1/4" x 12"
1-1/4" x 12"
00256692
00334742
10/200
00256693
00334743
10/200
00256694
00334744
10/200
00256702
00338262
5/100
00256695
00334745
5/100
00256696
00334746
5/60
00256699
3/8" x 5-1/8"
3/8" x 8"
1/2" x 6-1/2"
1/2" x 8"
1/2" x 10"
5/8" x 8"
5/8" x 12"
3/4" x 10"
3/4" x 12"
3/4" x 14"
7/8" x 10"
7/8" x 13"
1" x 12"
1" x 14"
1-1/4" x 16"
1-1/4" x 22"
00333183
00333186
00333190
00333191
00333192
00333194
00333195
00333201
00333202
00333203
00333208
00333209
00333210
00333211
00333214
00333215
00338468
00338469
00338470
00338471
00338472
00338473
00338474
00338475
00338476
00338477
00338478
00338479
00338480
00338481
00338482
00338483
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
00338932
00338935
00338939
00338940
00338941
00338943
00338944
00338947
00338949
00338950
00338955
00338956
00338957
00338958
00338961
00338962
240
160
160
120
120
80
60
40
30
30
20
20
16
16
8
8
HVU Adhesive Capsules
HAS-E Rods 5.81
HVU Qty
HVU/HAS-E Combo1
1 Requires setting nuts.
HVU Adhesive Capsules, HIS Internally Threaded Carbon Steel Inserts/HIS-R Stainless Steel Inserts
HIS Insert Carbon Steel
Product
Item No.
3/8" x 4-1/4"
1/2" x 5"
5/8" x 6-5/8"
3/4" x 8-1/4"
00258020
00258021
00258022
00258023
HIS-R Insert 316 SS

Product
Item No.
3/8" x 4-1/4"
1/2" x 5"
5/8" x 6-5/8"
3/4" x 8-1/4"
00258029
00258030
00258031
00258032

used with HIS inserts
Product
Item No.
1/2" x 4-1/4"
5/8" x 5"
7/8" x 6-5/8"
1" x 8-1/4"
00256693
00256694
00256695
00256696
HIS Setting Tool

Drive Socket*
Item No.
9/16"
3/4"
15/16"
1-1/8"
00045969
00045970
00045971
00045972
Qty per Box

HIS
HVU
10
5
5
5
10
10
5
5
*Required for HIS setting tool
www.us.hilti.com
7.21
Heavy Duty Anchor

HVA Allowable Bond Strength and Steel Strength for HAS Rods in Concrete4
HVU Allowable Tensile Bond Strength (lb)2
2000 psi
3000 psi
4000 psi
Concrete
Concrete
Concrete
Anchor
Dia
Embedment
Depth
HVU Capsule
Required
3/8"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
3-1/2"
4-1/4"
5"
6-5/8"
6-5/8"
8-1/4"
12 "
(1) 3/8 x 3-1/2

(1) 1/2 x 4-1/4
(1) 5/8 x 5
(1) 3/4 x 6-5/8
(1) 7/8 x 6-5/8
(1) 1 x 8-1/4
(1) 1-1/4 x 12
2085
3250
3970
6080
7145
8640
19175
2340
3990
4605
7345
8135
11035
21545
2595
4735
5245
8615
9130
13425
23920
Allowable Steel Strength1,2

HAS Super
Tensile
Shear
(lb)
(lb)
HAS-E
Tensile
Shear
(lb)
(lb)
2640
4700
7340
10570
14385
18790
29360
1360
2420
3780
5445
7410
9680
15125
4555
8100
12655
18225
24805
32400
50620
2345
4170
6520
9390
12780
16690
26080
Tensile
(lb)
HAS 304 SS
Shear
(lb)
3645
6480
10125
12390
16865
22030
34425
1875
3335
5215
6385
8690
11350
17735
1, 2, 3, 4 See notes below.
HVA Ultimate Bond Strength and Steel Strength for Rebar in Concrete
Anchor
Dia
Embedment
Depth
HVU Capsule
Required
Rebar #4
Rebar #5
Rebar #6
Rebar #7
Rebar #8
4-1/4"
5"
6-5/8"
6-5/8"
8-1/4"
(1) 1/2 x 4-1/4

(1) 5/8 x 5
(1) 7/8 x 6-5/8
(1) 1 x 8-1/4
(1 ea.) 1 x 8-1/4 & 5/8 x 5
Curing Times
HVU Tensile Bond Strength (lb)2

2000 psi
3000 psi
4000 psi
Concrete
Concrete
Concrete
Grade 60 Rebar Strength

Tensile
Yield
(lb)
(lb)
9680
15000
21020
23650
35640
18000
27900
39600
54000
71100
10980
16920
24250
27280
40500
12270
18830
27470
30910
45360
12000
18600
26400
36000
47400
Approx. Curing Time
20 Minutes
30 Minutes
1 Hour
5 Hour
Base Material Temp*
Above 68F/20C
50F/10C
32F/0C
23F/-5C
* For temperatures below 23F/-5C,

consult your Hilti Engineer.
1, 2, 3, 4 See notes below.
HVA Allowable Bond and Steel Strength for HIS & HIS-R Internally Threaded Inserts4
Anchor
Embedment
HVU Capsule
HVU Bond Strength (lb)2
Dia
Depth
Required
in Concrete 2000 psi
Tension (lb)
Shear (lb)
3/8"
1/2"
5/8"
3/4"
4-1/4"
5"
6-5/8"
8-1/4"
1/2 x 4-1/4
5/8 x 5
7/8 x 6-5/8
1 x 8-1/4
3180
4570
7460
9165
4860
8635
13500
19440
1875
3335
5215
7510
1 Steel strength as defined in AISC Manual of Steel Construction (LRFD, except where shear is limited
by concrete strength. Shear values based on anchors installed at standard embedment.
2 Use lower value of either bond or steel strength for tensile load.
Steel Bolt Strength2, 3
3 Steel values based on AISC values for A325 Bolts (fy = 92 ksi, fu = 120 ksi).
4 Bond values based on a safety factor of 4.
Steel values based on a safety factor of 2.27 for tension end 2.65 for shear.
Square Drive Shaft
HAS-E Threaded Rod w/Setting Nut
HIS Internally Threaded Sleeve Insert
Drive Socket
HIS Setting Tool

Rebar
Setting Products
HAS Rod,
HIS/
Rebar
Diameter
Item No 00032220
TE-C + SD-1/2"
Item No.
Drive Socket
Square Drive Shaft

Item No 0032221
TE-Y-SD-3/4" (00332169)
Item No.
Drive Socket
3/8"
00065277 9/16" x 1/2"
1/2" / #4 00065278 3/4" x 1/2" 00065279
5/8" / #5 00065280 15/16" x 1/2" 00065281
3/4" / #6
00065282
7/8" / #7
00065283
1" / # 8
00065284
1-1/4"
3/4" x 3/4"
15/16" x 3/4"
1-1/8" x 3/4"
1-7/16" x 3/4"
1-1/2" x 3/4"
Setting Nuts2,3
Item No 00220693
TE-Y-SD-1"
Item No.
Drive Socket
Item No.
00045138
00045140
00045139
00045141
00045142
00045143
00065285 1-7/8" x 1" 00045144
Rebar Setting Tools
Qty/Pkg
10
10
5
5
5
5
5
HIS Setting
Tool1
Item No.
HIS Drive
Socket
Size Rqd
TE-Y
Item No.
00045969 9/16"
00045970 3/4" 00220695
00045971 15/16" 00220696
00045972 1-1/8" 00220697
00220698
00220699
Adapter
#4
#5
#6
#7
#8
1 To be used with appropriate drive socket and drive shaft from selector chart above. Setting nuts not required with HIS setting tools.
2 Setting nuts are required for proper fit of drive socket.
3 Setting nuts have a black finished coating except 7/8" which are HDG.
Accessories
24" Air Nozzle
Item No.
Description
00063964
Air Nozzle (Length 24")
Use
For all hole sizes 24"
www.us.hilti.com
7.22
Heavy Duty Anchor

Approvals
Hilti HDA:
The Ideal Solution For Heavy Duty/Safety Fastening

ER-5608

RR-25422
HDA-T
Through-Set Anchor
HDA-P
Pre-Set Anchor
Advantages
Unity with the base material
Self-undercutting anchor installs in one

The undercut is formed during the setting
minutefast and easy setting operation
operation as the rotating segments are
forced outwards by the tapered section. The
Performance comparable to cast-in
resulting keying hold remains secure even
headed studs
in cracked concrete under dynamic loading.
Excellent for resisting seismic and shock
HDA Removal Tool
Fully removable for temporary fastening
Features
Reduced expansion forces during
gold medal
installation allow small edge distance and
Threads are stripped during anchor removal to
Winner 2000
close anchor spacing
prevent reuse for safety reasons
Reliable ductile steel failure in virtually all strengths of
Suitable for all rotary hammers with TE-C type
concrete 2500 psi
chucks
Undercut allows use in tension zones and cracked
concrete
HDA Drill Bits & Required Setting/Removal Tools/ Technical Data

HDA Drill Bits & Setting Tool
HDA-T Anchor
Minimum 2500 psi
Concrete Strength
Item No.
Anchor (mm)
(dia x min. emb.
/max. thickness fastened)
HDA-T
Item No.
(Galvanized)
HDA-T F1
Item No.
(Sherardised)
HDA-T R
Item No.
(316 Stainless)
Qty/box
00331545
00331548
00331549
00331552
00331553
00339267
00339268
HDA-T M10x100/20
HDA-T M12x125/30
HDA-T M12x125/50
HDA-T M16x190/40
HDA-T M16x190/60
HDA-T M20x250/50
HDA-T M20x250/100
331545
331548
331549
331552
331553
339267
339268
339361
339362
339363
339364
339365
---
339351
339352
339353
339354
339355
---
12
8
8
4
4
2
2
Item No.
Anchor (mm)
(dia x min. emb.
/max. thickness fastened)
HDA-P
Item No.
(Galvanized)
HDA-P F1
Item No.
(Sherardised)
HDA-P R
Item No.
(316 Stainless)
Qty/box
00331544
00331546
00331547
00331550
00331551
00339265
00339266
HDA-P M10x100/20
HDA-P M12x125/30
HDA-P M12x125/50
HDA-P M16x190/40
HDA-P M16x190/60
HDA-P M20x250/50
HDA-P M20x250/100
331544
331546
331547
331550
331551
339265
339266
339356
339357
339358
339359
339360
---
339346
339347
339348
339349
339350
---
12
8
8
4
4
2
2
Tension, lb
Shear, lb
For complete Load Values,

refer to the
SeeTechnical
load Guide,
values.
2002 Ed.,
Section 4.3.1
Max. fastenable
thickness,
tfix. (in)
Clearance
hole,
dh (in)
Drill bit
depth,
h1 (in)
Anchorage
length,
l (in)
Socket Size
for nut
(mm)
3/8
1 3/16
2
1 5/8
2 3/8
2
4
7/8
1
1
1 1/4
1 1/4
1 5/8
1 5/8
4 7/32
5 5/16
5 5/16
8
8
10 1/2
10 1/2
6
7 1/2
8 1/4
10 13/16
11 5/8
14 3/16
16 1/8
17
19
19
24
24
30
30
Max. fastenable
thickness,
tfix (in).
Clearance
hole,
dh (in)
Drill bit
depth,
h1 (in)
Anchorage
length,
l (in)
Socket Size
for nut
(mm)
3/8
1 3/16
2
1 5/8
2 3/8
2
4
7/16
9/16
9/16
11/16
11/16
15/16
15/16
1. Standard lead time of 6 to 8 weeks
HDA-P Anchor
Minimum 2500 psi
Concrete Strength
Tension, lb
Shear, lb

refer to the
SeeTechnical
load Guide,
values.
2002 Ed.,
Section 4.3.1
4 7/32
6
5 5/16
7 1/2
5 5/16
8 1/4
8
10 13/16
8
11 5/8
10 1/2 14 3/16
10 1/2
16 1/8
17
19
19
24
24
30
30
1. Standard lead time of 6 to 8 weeks
www.us.hilti.com
7.23
Heavy Duty Anchor
Examples Of Through-Fastening And Pre-Setting
Steel Construction
Pipe Installation
Machine fastening
Reliable heavy-duty fastening
High shear forces are taken up without difficulty,

for example, when installing large-diameter pipes
Maximum safety under dynamic loading for

fastening machines
HDA-T
HDA-P
Definition of Nomenclature
P-pre-set before baseplate
T-through-set after/
through base plate
metric
threaded diameter (mm)
HDA-P-F M 12 x 125/50
Hilti
Design
Anchor
Stop Drill Bit
Hilti Diamond Core Bit
Item No.
Description (mm)
(dia x
drill depth)
00332090
00332092
00332093
00332098
00332099
00339271
00339272
TE-C-B20x120
TE-C-B22x155
TE-C-B22x175
TE-Y-B30x230
TE-Y-B30x250
TE-Y-B37x300
TE-Y-B37x350
Stop Drill Bit
Item No.
Diameter
00239782
00306736
00306736
00306739
00306739
00251068
00251068
20 mm (25/32")
22 mm (7/8")
22 mm (7/8")
30 mm (1-1/8")
30 mm (1-1/8")
37 mm
37 mm
Hilti Diamond Core Bit
Item No.
Description (mm)
(dia x
drill depth)
00332089
00332091
00332091
00332097
00332097
00339270
00339270
TE-C-B20x100
TE-C-B22x125
TE-C-B22x125
TE-Y-B30x190
TE-Y-B30x190
TE-Y-B37x250
TE-Y-B37x250
Item No.
Diameter
00239782
00306736
00306736
00306739
00306739
00251068
00251068
20 mm (25/32")
22 mm (7/8")
22 mm (7/8")
30 mm (1-1/8")
30 mm (1-1/8")
37 mm
37 mm
Setting Tool
blank-carbonsteel zinc plated

F-Carbon steel (HDG)
R-316 stainless steel
Item No.
Setting Tool
Hammer Drill
for Anchor
Installation
Item No.
00331843
00331844
00331844
00331846
00331846
00339269
00339269
TE-C-ST-M10
TE-C-ST-M12
TE-C-ST-M12
TE-Y-ST-M16
TE-Y-ST-M16
TE-Y-ST-M20
TE-Y-ST-M20
00308334
00308334
00308334
00258460
00258460
00258460
00258460
Item No.
Setting Tool
Hammer Drill
for Anchor
Installation
Item No.
00331843
00331844
00331844
00331846
00331846
00339269
00339269
TE-C-ST-M10
TE-C-ST-M12
TE-C-ST-M12
TE-Y-ST-M16
TE-Y-ST-M16
TE-Y-ST-M20
TE-Y-ST-M20
Setting Tool
00308334
00308334
00308334
00258460
00258460
00258460
00258460
Minimum
embedment
of undercut
Maximum
fastening
thickness
Removal Tool For Anchor (With Adapter)
Hammer Drill
TE 25
TE 25
TE 25
TE 76
TE 76
TE 76
TE 76
Item No.
Description
00333433 TE-C-HDA-RT M10

00333434 TE-C-HDA-RT M12
00333435 TE-C-HDA-RT M16
00339273 TE-C-HDA-RT M20
Removal Tool For Anchor (With Adapter)
Hammer Drill
TE 25
TE 25
TE 25
TE 76
TE 76
TE 76
TE 76
Item No.
Description
00333433 TE-C-HDA-RT M10

00333434 TE-C-HDA-RT M12
00333435 TE-C-HDA-RT M16
00339273 TE-C-HDA-RT M20
www.us.hilti.com
7.24
Heavy Duty Anchor

Approvals

HSL Heavy-Duty Expansion Anchor
SBCCI Report No. 9930

Embedment
mark
ES Report No. 3987
Advantages
Plastic
collapsible
section

Report No. 25290
360
expansion
sleeve
Inner bolt
or
stud
Spacer
sleeve
Anchor Program
HSL Heavy-Duty Anchor

Bolt head for applications where finished appearance is required. Easy
removal and re-installation of inner bolt allows for flexible anchoring systems.
ICBO AC01 testing allows usage

in seismic applications
Bolt head versions available to
provide flexibility of flush
mounted, low profile applications
Steel spacer sleeve for fewer
fasteners in high shear load
applications
Heavy-duty expansion sleeve and
collapsible mid section provides
positive clamping of fastened
materials to concrete
Heavy-duty expansion sleeve
allows installation in Hilti
matched tolerance diamondcored holes
Heavy-duty expansion sleeve
provides follow up expansion for
fastenings in tension zones of
concrete such as under bridge
decks, floor slabs and beams
HSLG-I M12 (1/2") is perfect for
thin slab applications requiring a
flush-mounted fastener
HSLB Heavy-Duty Anchor with Indicator Cap

Pre-determined torque is automatically achieved by shearing off red torque
cap with ordinary wrench. No torque wrench is required. Inspection is made
easy with green indicator seal, revealed when red torque cap shears off.
HSLG-N Heavy-Duty Anchor with Threaded Rod (Stud Version)

Variable rod lengths available for standoff anchoring (shimming and levelling).
Slotted end allows removal of inner threaded rod after installing anchor.
Stainless steel version for corrosive environments available (HSLG-R).
NEW!
HSLG-I M12/0 *65-80 Flush Anchor
(Internally Threaded; 12mm Diameter)
Flush mount applications accommodated by standard and shallow
embedments. Correct torque obtained by shearing the torque nut with an
ordinary wrench. Inspection after installation facilitated by red plastic ring on
standard nut.
Bolt/Rod Material
HSLG-R:
HSL/HSLG-N (zinc plated):
Stainless Steel Type 316

Carbon Steel 8.8
min. fu = 101.5 ksi

min. fu = 116 ksi
Definition of Nomenclature
www.us.hilti.com
7.25
blank - carbon steel

N - slot at rod end
R - stainless steel
Heavy Duty
Expansion Anchor
Metric
HSLG-R M 12/25
blank-bolt
G-stud
B-Torque Cap
I-Internal Thread
Maximum fastened
thickness (mm)
Thread size (mm); not hole
diameter (see specification
following page)
fy = 65.3 ksi
fy = 92.8 ksi
Example:
HSLG-RM12/25
This is an HSL stud anchor.
The anchor material is type
316 Stainless Steel. The
thread size is 12 mm and this
anchor can attach up to a 25
mm thick plate.
Heavy Duty Anchor

HSL (Bolt Version)
Item No
Description
Bit dia
(mm)
Anchor
Length
(mm)
Minimum
Embedment
Depth (mm)
00066573
00066575
00066576
00066578
00066592
00066593
00066594
00066595
00066596
00066597
00260383
00260384
HSL M 8/20
HSL M 8/40
HSL M 10/20
HSL M 10/40
HSL M 12/25
HSL M 12/50
HSL M 16/25
HSL M 16/50
HSL M 20/30
HSL M 20/60
HSL M 24/30
HSL M 24/60
12
12
15
15
18
18
24
24
28
28
32
32
95
115
107
127
120
145
148
173
183
213
205
235
65
65
75
75
80
80
105
105
130
130
155
155
Average Ultimate Loads

in 4000 psi Concrete
Tension (lb)
Shear (lb)
5870
5870
8500
8500
11240
11240
20205
20205
25500
25500
34390
34390
8345
8345
13220
13220
18900
18900
33640
33640
45020
45020
62615
62615
Allowable Working Loads

4000 psi Concrete
Tension (lb)
Shear (lb)
1680
1680
2435
2435
3220
3220
5790
5790
7310
7310
9860
9860
Qty
Box
2390
2390
3790
3790
5420
5420
9645
9645
12905
12905
17950
17950
40
40
20
20
20
20
10
10
6
6
4
4

4000 psi Concrete
Tension (lb)
Shear (lb)
Qty
Box
HSLB Torque Cap

Item No
Description
Bit dia
(mm)
Anchor
Length
(mm)
Minimum
Embedment
Depth (mm)
00045706
00067400
00067401
00045707
00067402
00067404
00260385
HSLB M 12/6
HSLB M 12/25
HSLB M 12/50
HSLB M 16/6
HSLB M 16/25
HSLB M 20/30
HSLB M 24/30
18
18
18
24
24
28
32
100
120
145
148
183
205
80
80
80
105
105
130
155

Tension (lb)
Shear (lb)
11240
11240
11240
20205
20205
25500
34390
18900
18900
18900
33640
33640
45020
62615
3220
3220
3220
5790
5790
7310
9860
5420
5420
5420
9654
9654
12905
17950
20
20
20
10
10
6
4

4000 psi Concrete
Tension (lb)
Shear (lb)
Qty
Box
HSLG-N Stud Anchor

Item No
Description
Bit dia
(mm)
Anchor
Length
(mm)
Minimum
Embedment
Depth (mm)
00068411
00068425
00068439
00068440
00068452
00068453
00068465
00068467
HSLG-N 8/20
HSLG-N 10/20
HSLG-N 12/25
HSLG-N 12/50
HSLG-N 16/25
HSLG-N 16/50
HSLG-N 20/30
HSLG-N 20/60
12
15
18
18
24
24
28
28
95
107
120
145
148
173
183
213
65
75
80
80
105
105
130
130

Tension (lb)
Shear (lb)
5870
8500
11240
11240
20205
20205
25500
25500
6845
10840
15500
15500
27585
27585
36915
36915
1680
2435
3220
3220
5790
5790
7310
7310
1965
3110
4445
4445
7910
7910
10585
10585
40
20
20
20
10
10
6
6

4000 psi Concrete
Tension (lb)
Shear (lb)
Qty
Box
HSLG-I Flush Anchor (Internally Threaded; 12mm Diameter)1

Item No
Description
00374627 HSLG-I M12/0 *65-80
Bit dia
(mm)
Anchor
Length
(mm)
Minimum
Embedment
Depth (mm)
18
113/130
65/80

Tension (lb)
Shear (lb)
9345/12597
9055/9408
2480/2875
2420/2605
20
12mm Metric Flush Anchor with Torque Nut

1 Loads indicated are for 65/80 mm embedment respectively.
HSLG-R Stainless Steel Stud Anchor

Item No
Description
Bit dia
(mm)
Anchor
Length
(mm)
Minimum
Embedment
Depth (mm)
00067922
00067924
00067926
00067928
HSLG-R M 10/20
HSLG-R M 12/25
HSLG-R M 16/25
HSLG-R M 20/30
15
18
24
28
107
120
148
183
75
80
105
130

Tension (lb)
Shear (lb)
8985
10835
19005
28520
12410
18300
35320
50540

4000 psi Concrete
Tension (lb)
Shear (lb)
2575
3105
5450
8175
3560
5245
10125
14490
Qty
Box
20
20
10
6
www.us.hilti.com
7.26
Heavy Duty Anchor

HSL Metric Specification Table
Anchor Thread Size (mm)
Specifications
Drill Bit Diameter = Anchor O.D.(mm)

Hole Depth (mm)
Min. Depth of Embedment (mm)
Max.Thickness Fastened (mm)
Anchor Length (mm)
Head Height + Washer (mm)
Max.Tightening Torque (ft-lb)
Max.Gap Between Concrete & Fastened Mat'l (mm)
Wrench Size (mm)
HSL/HSLG
Wrench Size (mm)
HSLB
Clearance Hole Thru Fastened Mat'l (mm)
Washer Diameter (mm)
Min. base Material Thickness (mm)
Drill Bit
Hammer Drill
10
12
75
65
10
15
85
75
20
95
40
115
7.5
20
4
13
14-15
20
120
TE-CX 12/22
00205343
TE-YX 12/35
00333753
TE5,TE6-A
TE15,TE18M
TE25,TE55
TE76
20
107
40
127
10
40
5
17
17-18
25
140
TE-CX 15/27
00205366
TE-YX 15/35
00333758
TE5,TE6-A
TE15,TE18M
TE25,TE55
TE76
12
12
18
100
80
25
50
120
145
11
60
8
19
24
20-21
30
160
TE-C 18/22
00028002
TE-YX 18/32
00339015
TE15,TE15C
TE18M,TE25
TE55,TE76
12-I*
12-I*
18
76
65
90
80
38
113
130
TN
60
19
20-21
30
120
160
TE-C 18/22
00028002
TE-YX 18/32
00339015
TE15,TE15C
TE18M,TE25
TE55,TE76
16
16
24
125
105
25
50
148
173
14
150
9
24
30
26-28
40
180
TE-C-T 24/27
00028011
TE-YX 24/32
00339024
TE15,TE18M
TE25,TE55
TE76
20
20
28
150
130
30
60
183
213
17
300
12
30
36
31-33
45
220
TE-C-T 28/27
00028016
TE-YX 28/32
00339030
TE25,TE55,
TE76
24
24
32
175
155
30
60
205
235
19
525
16
36
41
35-37
50
270
TE-YX 32/37
00339034
TE55,TE76
See definition of nomenclature. Thread size differs from drill diameter. To convert millimeters (mm) to inches divide by 25.4.
*12-I indicates HSLG-I M12/0 *65/80 with torque nut.
HSL Specification Table - Approximate Fractional Equivalents (for Comparison Only)

Anchor Thread Size (mm)
Specifications
Anchor Outside Diameter1

Clearance Hole Thru Fastened Material
Equivalent Fractional Anchor Size2
Thread Diameter3 (approximate)
Hole Depth
Maximum Thickness Fastened
Overall Anchor Length
Head Height + Washer
10
10
12
12
12-I
12-I
16
16
20
20
24
24
1/2"
9/16"
11/16"
11/16"
1"
1-1/8"
1-1/4"
9/16"
11/16"
13/16"
13/16"
1-1/16"
1-1/4"
1-7/16"
1/2"
5/8"
3/4"
3/4"
1"
1-1/8"
1-1/4"
5/16"
3/8"
1/2"
1/2"
5/8"
3/4"
15/16"
3"
3-3/8"
4"
3" 3-1/2"
5"
6"
7"
3/4" 1-1/2" 3/4" 1-1/2" 1"
2"
1-1/2"
1"
2" 1-3/16" 2-3/8" 1-3/16" 2-3/8"
3-3/4" 4-1/2" 4-3/16" 5" 4-11/16" 5-11/16" 4-1/2" 5-1/8" 5-13/16" 6-13/16" 7-3/16" 8-3/8" 8-1/16" 9-1/4"
5/16"
3/8"
7/16"
9/16"
11/16"
3/4"
1 Approximate fractional equivalent only; correct metric drill bit must be used.
2 The metric anchor will fit through fixture holes normally specified for this diameter anchor.
3 Actual thread is metric; nut or coupler must have metric threads.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.27
Medium Duty Anchor

Listings/Approvals
Meets the description in Federal
Specification
Kwik Bolt II Expansion Anchor

Unique Wedge Design Satisfies Wide Range of Fastening Applications
FF-S-325, Group II, Type 4, Class 1

Nut
Washer
UL (Underwriter Laboratories)
Collar
Prevents wedges from
sliding up anchor body
Anchor Body
Wedge Dimple
Prevents spinning
in the hole
Listed Std. No 203, Pipe Hangers

(3/8"to 3/4" diameters)
FM (Factory Mutual)
Listed Pipe Hangers
(3/8" KBII with Rod Coupling)

Evaluation Report No. 4627

Wedges
Improved wedge
design ensures more
consistent and
reliable fastening
Impact Section
(Dog Point)
Prevents thread damage
during installation
Expansion Cone
Provides consistent
expansion of wedges
Report No. 9930

Research Report No. 24946
Metro-Dade County Approval

98.0901.13
Product Details
Kwik Bolt II anchor sizes range from 1/4" to 1" in diameter and
are supplied with washers and nuts or rod couplings.
Advantages
Anchor Program
Impact section (Dog Point) prevents thread damage

during installation
Independent 3-piece wedge with dimples prevents
anchor from spinning during installation
Length identification code facilitates quality control
and inspection after installation
Anchor size is same as drill bit size for easy
installation
Comprehensive performance testing demonstrating
high and consistent performance in concrete, lightweight concrete and grout filled block base materials
Mechanical expansion allowsimmediate load
application
Can be installed in bottomless hole, which allows the
anchor to be driven flush with the surface after use,
eliminating the need to cut bolt heads
Can be installed through the fixture, improving
productivity
Comprehensive product offering includes many head
styles, sizes, carbon steel and stainless steel
materials for a variety of applications
Standard Kwik Bolt II

Long Thread Kwik Bolt II
304 and 316 Stainless Steel Kwik Bolt II
(all component parts of same stainless steel grade)
Countersunk Post Nut
(Carbon and 304 Stainless Steel)
Eyelet Anchor
Rod Coupling Kwik Bolt II
Custom special orders available in
various lengths and materials
Hilti Tamper Proof Nut (HTN)
Length
Identification Mark
Kwik Bolt II Length Identification System

Stamp on Anchor
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
From 1-1/2 2 2-1/2 3 3-1/2 4 4-1/2 5 5-1/2 6 6-1/2 7 7-1/2 8 8-1/2 9 9-1/2
Length of Up To
Anchor
But Not 2 2-1/2 3 3-1/2 4 4-1/2 5 5-1/2 6 6-1/2 7 7-1/2 8 8-1/2 9 9-1/2 10
(inches) Including
Stamp on Anchor
R
From 10
Length of Up To
Anchor
But Not 11
(inches) Including
S
11
T
12
U
13
V
14
W
15
X
16
Y
17
Z
18
12
13
14
15
16
17
18
19
Stamp on Anchor AA
From 19
Length of Up To
Anchor
But Not 20
(inches) Including
BB
20
CC
21
DD
22
EE
23
FF
24
GG
25
HH
26
II
27
JJ
28
KK
29
LL
30
MM NN
31 32
OO
33
PP QQ
34 35
21
22
23
24
25
26
27
28
29
30
31
32
34
35
Stamp on Anchor RR
From 36
Length of Up To
Anchor
But Not 37
(inches) Including
SS
37
TT
38
UU
39
VV WW XX
40
YY
ZZ
38
39
40
41
33
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
36
www.us.hilti.com
7.28
arton
MasterallCets
&P
Medium Duty Anchor
B e s t Va l
Kwik Bolt II Anchor Program
ue

Kwik Bolt Specification Table
Anchor Size
Setting Details
KB II 1/4"
KB II 3/8"
KB II 1/2"
BD = D drill bit size = anchor diameter (in.)

E
depth of embedment (minimum:standard) (in.)
HD
hole depth E + D (minimum:standard) (in.)
DC
wedge clearance hole (in.)
L
anchor length (minimum:maximum) (in.)
TL
thread length (standard:extra) (in.)
M
Installation
stainless min. E
torque (ft-lb) steel
std. E
guide values carbon
min. E
steel
std. E
BMT minimum base material thickness (in.)
1/4
3/8
1/2
1-1/8 : 2
1-5/8 : 2-1/2 2-1/4 : 3-1/2
1-3/8 : 2-1/4 2 : 2-7/8
2-3/4 : 4
5/16
7/16
9/16
1-3/4 : 4-1/2 2-1/4 : 7
2-3/4 : 7
3/4 : 3
7/8 : 4
1-1/4 : 4
4
20
40
7
30
75
4
20
40
7
25
65
All: 3 or 1.3E whichever number is greater
KB II 5/8"
KB II 3/4"
KB II 1"
5/8
2-3/4 : 4
3-3/8 : 4-5/8
11/16
3-3/4 : 10
1-1/2 : 4-1/2
85
110
85
110
3/4
3-1/4 : 4-3/4
4 : 5-1/2"
13/16"
4-3/4 : 12
1-1/2 : 4-1/2
150
200
150
235
1
4-1/2 : 6
5-1/2 : 7
1-1/8
6 / 12
2-1/4 : 4-1/2
235
450
250
450
Carbon Steel Kwik Bolt II

Item No.
(Box)
Master
Carton#
(MC)
Description
00045359
00045360
00045361
00045362
00045363
00045364
00045365
00045366
00045367
00045368
00045369
00045370
00045371
00045372
00045373
00045374
00045375
00045376
00045377
00045412
00045413
336024
336025
336026
336027
336028
336029
336030
336031
336032
336033
336034
336035
336036
336037
336038
336039
336040
336041
336042
336043
336044
KB II 1/4-1-3/4
KB II 1/4-2-1/4
KB II 1/4-3-1/4
KB II 3/8-2-1/4
KB II 3/8-3
KB II 3/8-3-3/4
KB II 3/8-5
KB II 1/2-2-3/4
KB II 1/2-3-3/4
KB II 1/2-4-1/2
KB II 1/2-5-1/2
KB II 5/8-3-3/4
KB II 5/8-4-3/4
KB II 5/8-6
KB II 5/8-7
KB II 3/4-4-3/4
KB II 3/4-5-1/2
KB II 3/4-7
KB II 3/4-8
KB II 1-6
KB II 1-9
Bit
dia
Anchor
Length
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
1"
1"
1-3/4"
2-1/4"
3-1/4"
2-1/4"
3"
3-3/4"
5"
2-3/4"
3-3/4"
4-1/2"
5-1/2"
3-3/4"
4-3/4"
6"
7"
4-3/4"
5-1/2"
7"
8"
6"
9"
Min
Emb
Depth
Thread
Length
1-1/8" 3/4"
1-1/8" 3/4"
1-1/8" 3/4"
1-5/8" 7/8"
1-5/8" 1-1/8"
1-5/8" 1-1/8"
1-5/8" 1-1/8"
2-1/4" 1-1/4"
2-1/4" 1-1/4"
2-1/4" 1-1/4"
2-1/4" 1-1/4"
2 3/4" 1-1/2"
2 3/4" 1-1/2"
2 3/4" 1-1/2"
2 3/4" 1-1/2"
3-1/4" 1-1/2"
3-1/4" 1-1/2"
3-1/4" 1-1/2"
3-1/4" 1-1/2"
4-1/2" 2-1/4"
4-1/2" 2-1/4"
Hilti
Drill Bit
Ultimate Loads
Emb Depth Tension (lb) Shear (lb)
Allowable Wk Loads
TE-CX 1/4-6
TE-CX 1/4-6
TE-CX 1/4-6
TE-CX 3/8-6
TE-CX 3/8-6
TE-CX 3/8-6
TE-CX 3/8-12
TE-CX 1/2-6
TE-CX 1/2-6
TE-CX 1/2-12
TE-CX 1/2-12
TE-C+ 5/8-8
TE-C+ 5/8-8
TE-C+ 5/8-12
TE-C+ 5/8-12
TE-C-S 3/4-8
TE-C-S 3/4-8
TE-C-S 3/4-12
TE-C-S 3/4-12
TE-Y 1-13
TE-Y 1-13
1-1/8"
2"
2"
1-5/8"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-1/2"
6"
1 1/8"
2"
2"
1-5/8"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-1/2"
6"
Hilti
Drill Bit
Ultimate Loads
Allowable Wk Loads
TE-CX 1/4-8
TE-CX 3/8-6
TE-CX 3/8-6
TE-CX 3/8-12
TE-CX 3/8-12
TE-CX 1/2-6
TE-CX 1/2-12
TE-CX 1/2-12
TE-CX 1/2-12
TE-C 5/8-8
TE-C 5/8-12
TE-C 5/8-12
TE-C+ 5/8-12
TE-C+ 5/8-12
TE-C-S 3/4-8
TE-C-S 3/4-8
TE-C-S 3/4-12
TE-C-S 3/4-12
TE-C-S 3/4-18
TE-Y 1-21
2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
3-1/2"
4"
4"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
6"
2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
3-1/2"
4"
4"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
6"
1430
2350
2350
2825
5150
5150
5150
5450
5450
9000
9000
8000
12350
12350
12350
10000
18000
18000
18000
17500
26500
1600
20001
20001
3900
55001
55001
55001
7360
7360
92001
92001
11500
142002
142002
142002
15500
192002
192002
192002
30500
34500
380
630
630
750
1370
1370
1370
1450
1450
2400
2400
2130
3290
3290
3290
2670
4800
4800
4800
4670
7070
430
5301
5301
1100
14701
14701
14701
1970
1970
24501
24501
3070
38402
38402
38402
4140
51202
51202
51202
8140
9200
Qty
Box/MC
100/900
100/900
100/500
100/500
100/400
100/400
50/250
50/200
50/200
50/200
25/125
25/100
25/100
25/75
25/75
20/80
20/60
10/40
10/40
5/25
5/25
Long Thread Carbon Steel Kwik Bolt II

Item No.
(Box)
Master
Carton#
(MC)
Description
00045378
00331952
00331953
00331954
00242538
00331955
00331956
00331957
00045379
00331958
00369423
00331959
00045380
00045381
00331960
00331961
00332044
00332045
00045415
00045416
336045
336620
336621
336622
336046
336623
336624
336625
336047
336626
369424
336627
336048
336049
336628
336629
336630
336050
336051
336052
KB II 1/4 4-1/2
KB II 3/8 x 3
KB II 3/8 x 3-3/4
KB II 3/8 x 5
KB II 3/8 x 7
KB II 1/2 x 3-3/4
KB II 1/2 x 4-1/2
KB II 1/2 x 5-1/2
KB II 1/2 x 7
KB II 5/8 x 4-3/4
KB II 5/8 x 6
KB II 5/8 x 7
KB II 5/8 x 8-1/2
KB II 5/8 x 10
KB II 3/4 x 4-3/4
KB II 3/4 x 5-1/2
KB II 3/4 x 7
KB II 3/4 x 10
KB II 3/4 x 12
KB II 1 x 12
Bit
dia
Anchor
Length
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
1"
4-1/2"
3"
3-3/4"
5"
7"
3-3/4"
4-1/2"
5-1/2"
7"
4-3/4"
6"
7"
8-1/2"
10"
4-3/4"
5-1/2"
7"
10"
12"
12"
Min
Emb
Depth
Thread
Length
1-1/8" 3"
1-5/8" 1-3/4"
1-5/8" 2-1/2"
1-5/8" 3-1/4"
1-5/8" 4"
2-1/4" 2-1/4"
2-1/4" 3"
2-1/4" 3"
2-1/4" 4"
2-3/4" 2-1/2"
2-3/4" 2-1/2"
2-3/4" 4"
2-3/4" 3-1/2"
2-3/4" 4-1/2"
3-1/4" 2-1/2"
3-1/4" 3-1/2"
3-1/4" 4-1/2"
3-1/4" 4-1/2"
3-1/4" 4-1/2"
4-1/2" 4-1/2"
2350
5150
5150
5150
5150
5450
9000
9000
9000
12350
12350
12350
12350
12350
10000
18000
18000
18000
18000
26500
2000
55001
55001
55001
5500
73601
92001
92001
9200
142002
142002
142002
14200
14200
155002
192002
192002
19200
19200
34500
630
1370
1370
1370
1370
1450
2400
2400
2400
3290
3290
3290
3290
3290
2670
4800
4800
4800
4800
7070
530
14701
14701
14701
1470
19701
24501
24501
2450
38402
38402
38402
3840
3840
41402
51202
51202
5120
5120
9200
Qty
Box/MC
100/500
100/400
100/400
50/250
50/200
50/200
50/200
25/125
25/125
25/100
25/75
25/75
25/75
25/75
20/80
20/60
10/40
10/30
10/30
5/15
1 Values shown are for a shear plane acting through the anchor bolt shank. When the shear plane is acting through the anchor bolt threads, reduce the shear value by 15%.
2 Values shown are for a shear plane acting through the anchor bolt shank. When the shear plane is acting through the anchor bolt threads, reduce the shear value by 7%.
3 See Hilti Product Technical Guide for complete performance data.
7.29
arton
MasterallCets
P
&
304 Stainless Steel Kwik Bolt II
Item No.
(Box)
Master
Carton#
(MC)
Description
00230984
00230985
00230986
00230394
00230395
00230396
00230397
00229232
00229233
00229077
00229234
00045394
00045395
00045396
00045398
00045399
00045400
00045401
00045402
00045403
336053
336054
336055
336056
336057
336058
336059
336060
336061
336062
336063
336064
336065
336066
336067
336068
336069
336070
336071
336072
KB II 304 SSCF 1/4-1-3/4

KB II 304 SSCF 1/4-2-1/4
KB II 304 SSCF 1/4-3-1/4
KB II 304 SSCF 3/8-2-1/4
KB II 304 SSCF 3/8-3
KB II 304 SSCF 3/8-3-3/4
KB II 304 SSCF 1/2-2-3/4
KB II 304 SSCF 1/2-3-3/4
KB II 304 SSCF 1/2-4-1/2
KB II 304 SSCF 1/2-5-1/2
KB II 304 SSCF 5/8-3-3/4
KB II 304 SSCF 5/8-4-3/4
KB II 304 SSCF 3/4-4-3/4
KB II 304 SSCF 3/4-5-1/2
KB II 304 SSCF 1-6
KB II 304 SSCF 1-9
Medium Duty Anchor
ue
B e s t Va l
Bit
dia
Anchor
Length
Min
Emb
Depth
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
1"
1"
1-3/4"
2-1/4"
3-1/4"
2-1/4"
3"
3-3/4"
5"
2-3/4"
3-3/4"
4-1/2"
5-1/2"
3-3/4"
4-3/4"
6"
4-3/4"
5-1/2"
7"
8"
6"
9"
1-1/8"
1-1/8"
1-1/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-3/4"
2-3/4"
2-3/4"
3-1/4"
3-1/4"
3-1/4"
3-1/4"
4 1/2"
4-1/2"
Bit
dia
Anchor
Length
Min
Emb
Depth
1/4"
1/4"
3/8"
3/8"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
1"
2-1/4"
3-1/4"
3"
3-3/4"
3-3/4"
4-1/2"
5-1/2"
3-3/4"
4-3/4"
6"
4-3/4"
5-1/2"
6"
Thread Hilti
Length Drill Bit
3/4" TE-CX 1/4-6

3/4" TE-CX 1/4-6
3/4" TE-CX 1/4-6
7/8" TE-CX 3/8-6
1-1/8" TE-CX 3/8-6
1-1/8" TE-CX 3/8-6
1-1/8" TE-CX 3/8-12
1-1/4" TE-CX 1/2-6
1-1/4" TE-CX 1/2-6
1-1/4" TE-CX 1/2-12
1-1/4" TE-CX 1/2-12
1-1/2" TE-C+ 5/8-8
1-1/2" TE-C+ 5/8-8
1-1/2" TE-C+ 5/8-12
1-1/2" TE-C-S 3/4-8
1-1/2" TE-C-S 3/4-8
1-1/2" TE-C-S 3/4-12
1-1/2" TE-C-S 3/4-12
2 1/4" TE-Y 1-13
2-1/4" TE-Y 1-13

Ultimate Loads
Allowable Wk Loads
1-1/8"
2"
2"
1-5/8"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-1/2"
6"
1-1/8"
2"
2"
1-5/8"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-1/2"
6"
1300
2070
2070
2050
4700
4700
4700
4800
4800
8000
8000
6800
11000
11000
8800
14500
14500
14500
17300
27000
2200
2200
2200
4300
5000
5000
5000
7100
7100
8340
8340
12500
12500
12500
14000
18000
18000*
18000
28000
28000
350
550
550
550
1250
1250
1250
1280
1280
2130
2130
1810
2930
2930
2350
3870
3870
3870
4610
7200
590
590
590
1150
1330
1330
1330
1890
1890
2200
2200
3330
3330
3330
3730
4800
4800
4800
7470
7470
Qty
Box/MC
100/900
100/900
100/500
100/500
100/400
100/400
50/250
50/200
50/200
50/200
25/125
25/100
25/100
25/75
20/80
20/60
10/40
10/40
5/25
5/20
316 Stainless Steel Kwik Bolt II1

Item No.
(Box)
Master
Carton #
(MC)
Description
00238483
00238484
00238486
00238487
00238491
00238493
00238492
00045475
00045476
00045477
00045479
00045480
00045483
336073
336074
336075
336076
336077
336078
336079
336080
336081
336082
336083
336084
336086
KB II 316 SSCF 1/4-2-1/4

KB II 316 SSCF 1/4-3-1/4
KB II 316 SSCF 3/8-3-3/4
KB II 316 SSCF 1/2-3-3/4
KB II 316 SSCF 1/2-4-1/2
KB II 316 SSCF 1/2-5-1/2
KB II 316 SS 5/8-3-3/4
KB II 316 SS 5/8-4-3/4
KB II 316 SS 5/8-6
KB II 316 SS 3/4-4-3/4
KB II 316 SS 3/4-5-1/2
KB II 316 SS 1-6
Thread
Length
1-1/8" 3/4"
1-1/8" 3/4"
1- 5/8" 1-1/8"
1-5/8" 1-1/8"
2-1/4" 1-1/4"
2-1/4" 1-1/4"
2-1/4" 1-1/4"
2-3/4" 1-1/2"
2-3/4" 1-1/2"
2-3/4" 1-1/2"
3-1/4" 1-1/2"
3-1/4" 1-1/2"
4-1/2" 1-1/4"
Hilti Drill Bit
Ultimate Loads
Allowable Wk Loads
TE-CX 1/4-6
TE-CX 1/4-6
TE-CX 3/8-6
TE-CX 3/8-6
TE-CX 1/2-6
TE-CX 1/2-12
TE-CX 1/2-12
TE-C+ 5/8-8
TE-C+ 5/8-8
TE-C+ 5/8-12
TE-C-S 3/4-8
TE-C-S 3/4-8
TE-Y 1-13
2"
2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
3-1/4"
4-3/4"
4-1/2"
2"
2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
2-3/4"
4"
4"
3-1/4"
4-3/4"
4-1/2"
Hilti Drill Bit
Ultimate Loads in 4000 psi

Concrete at Std Emb Depth2
Allowable Wk Loads in 4000 psi

Concrete at Std Emb Depth2
TE-CX 1/4-8
TE-CX 3/8-6
TE-CX 3/8-6
TE-CX 3/8-12
TE-CX 3/8-12
TE-CX 1/2-6
TE-CX 1/2-12
TE-CX 1/2-12
TE-CX 1/2-12
TE-C 5/8-8
TE-C+ 5/8-12
TE-C+ 5/8-12
TE-C-S 3/4-8
TE-C-S 3/4-8
TE-C-S 3/4-12
TE-C-S 3/4-12
TE-C-S 3/4-18
TE-Y 1-21
2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
3-1/2"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
6"
2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/4"
3-1/2"
3-1/2"
3-1/2"
4"
4"
4"
3-1/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
6"
2070
2070
4700
4700
4800
8000
8000
6800
11000
11000
8800
14500
17300
2200
2200
5000
5000
7100
8340
8340
12500
12500
12500
14000
18000
28000
550
550
1250
1250
1280
2130
2130
1810
2930
2930
2350
3870
4610
590
590
1330
1330
1890
2200
2200
3330
3330
3330
3730
4800
7470
Qty
Box/MC
100/900
100/500
100/400
100/400
50/200
50/200
25/125
25/100
25/100
25/75
20/80
20/60
5/20
Stainless Steel Long Thread Kwik Bolt II1

Item No.
(Box)
Master
Carton #
(MC)
Description
00045404
00331962
00331963
00331964
00242539
00331965
00331966
00331967
00229235
00331968
00045407
00045408
00331969
00331970
00045409
00045490
00045410
00045411
336087
336631
336632
336633
336088
336634
336635
336636
336089
336637
336090
336091
336638
336639
336092
336085
336093
336094
KB II 304SS 1/4 x 4-1/2

KB II 304SS 3/8 x 3
KB II 304SS 3/8 x 3-3/4
KB II 304SS 3/8 x 5
KB II 304SS 3/8 x 7
KB II 304SS 1/2 x 3-3/4
KB II 304SS 1/2 x 4-1/2
KB II 304SS 1/2 x 5-1/2
KB II 304SS 1/2 x 7
KB II 304SS 5/8 x 4-3/4
KB II 304SS 5/8 x 8-1/2
KB II 304SS 5/8 x 10
KB II 304SS 3/4 x 4-3/4
KB II 304SS 3/4 x 5-1/2
KB II 304SS 3/4 x 10
KB II 316SS 3/4 x 10
KB II 304SS 3/4 x 12
KB II 304SS 1 x 12
Bit
dia
Anchor
Length
Min
Emb
Depth
Thread
Length
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
1"
4-1/2"
3"
3-3/4"
5"
7"
3-3/4"
4-1/2"
5-1/2"
7"
4-3/4"
8-1/2"
10"
4-3/4"
5-1/2"
10"
10"
12"
12"
1-1/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-3/4"
2-3/4"
2-3/4"
3-1/4"
3-1/4"
3-1/4"
3-1/4"
3-1/4"
4-1/2"
3"
1-3/4"
2-1/2"
3-1/4"
4"
2-1/4"
3"
3"
4"
2-1/2"
3-1/2"
4-1/2"
2-1/2"
3-1/2"
4-1/2"
4-1/2"
4-1/2"
4-1/2"
2070
4700
4700
4700
4700
4800
8000
8000
8000
11000
11000
11000
8800
14500
14500
14500
14500
27000
2200
5000
5000
5000
5000
7100
8340
8340
8340
12500
12500
12500
14000
18000
18000
18000
18000
28000
1 Additional 304 and 316 Stainless Steel sizes available through Custom Specials. Contact your nearest Hilti Representative.
2 See Product Technical Guide for complete performance data.
550
1250
1250
1250
1250
1280
2130
2130
2130
2930
2930
2930
2350
3870
3870
3870
3870
7200
Qty
Box/Ctn
590 100/500
1330 100/400
1330 100/400
1330 50/250
1330 50/200
1890 50/200
2200 50/200
2200 25/125
2220 25/125
3330 25/100
3330 25/100
3330 25/75
3730 20/80
4800 20/60
4800 10/30
4800 10/30
4800 10/30
7470
5/15
www.us.hilti.com
7.30
Medium Duty Anchor
Post Nut Series Anchors

Countersunk Kwik Bolt II
Item No.
(Box)
Master
Carton #
(MC)
Description
00045427
00045428
00045430
00045431
00045432
00045433
00045434
336095
336096
336097
336098
336099
336100
336101
KB II C1/4-2
KB II C1/4-3
KB II C1/4-5
KB II C3/8-2-1/4
KB II C3/8-3
KB II C3/8-4
KB II C3/8-5
Bit
dia
Anchor
Length
Min
Embed
Depth
Thread
Diameter
Thread
Length
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
2"
3"
5"
2-1/4"
3"
4"
5"
1-1/8"
1-1/8"
1-1/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
3/16"
3/16"
3/16"
5/16"
5/16"
5/16"
5/16"
7/16"
7/16'
7/16"
9/16"
9/16"
9/16"
9/16"
Anchor
Length
Min
Embed
Depth
Thread
Diameter
Thread
Length
3"
4"
1-1/8"
1-5/8"
3/16"
5/16"
7/16"
9/16"
Min
Embed
Depth
Thread
Rod
Coupling
1-5/8"
7/8"
1"
Min
Embed
Depth
Thread
Length
Eyelet
size
1/4"
Ultimate Working Loads1

3000 psi Concrete
Tension (lb)
Shear (lb)
1800
1800
1800
3240
3240
3240
3240
1400
1400
1400
3000
3000
3000
3000
Allowable Working Loads1

3000 psi Concrete
Tension (lb)
Shear (lb)
450
450
450
810
810
810
810
350
350
350
750
750
750
750
Qty
Box/MC
100/900
100/500
100/500
100/500
100/400
50/250
50/250
Stainless Steel Countersunk Kwik Bolt II

Item No.
(Box)
Master
Carton #
(MC)
Description
Bit
dia
00045435 336102 KB II 304SS C1/4-3 1/4"

00045436 336103 KB II 304SS C3/8-4 3/8"

3000 psi Concrete
Tension (lb)
Shear (lb)2
1920
3560
2000
5320

3000 psi Concrete
Tension (lb)
Shear (lb)2
480
880
500
1330
Qty
Box/MC
100/500
50/250
1 Round Head Post Nut Available in Standard and Stainless Steel through Special Orders.
2 Shear values for shear plane acting through threads of anchor bolt.
Rod Coupling Kwik Bolt II

Item No.
(Box)
Master
Carton #
(MC)
Description
Bit
dia
Anchor
Length
00045438 336104 KB II 3/8-2-1/4W/RC 3/8" 2-1/4"

00058387 Rod Coupler 3/8-16 for 3/8" all thread

3000 psi Concrete
Tension (lb)
Shear (lb)
2450
3900

3000 psi Concrete
Tension (lb)
Shear (lb)
650
1040
Qty
Box/MC
100/400
HCKB 1/4 Ceiling Hangers

Item No.
(Box)
Master
Carton #
(MC)
Description
00229630 248310 HCKB 14
Bit
dia
1/4"
Anchor
Length
2-1/2" 1-7/16"

Normal Wt Concrete
Tension (lb)
Shear (lb)
675
155

Light Wt Concrete
Tension (lb)
Shear (lb)
465
145
Qty
Box/MC
100/900
HHDCA 1/4 Ceiling Hangers

Item No.
(Box)
Master
Carton #
(MC)
Description
00371389 371390 HHDCA 1/4
Bit
dia
Anchor
Length
Min
Embed
Depth
Thread
Length
Eyelet
size
1/4"
2"
1-7/16"
1/4"

Normal Wt Concrete
Tension (lb)
Shear (lb)

Light Wt Concrete
Tension (lb)
Shear (lb)
Qty
Box/MC
100/1000
Hilti Tamper Proof Nut (HTN)

HTN is made of carbon steel conforming to ASTM A563 grade A and zinc plated in accordance with ASTM B633 SC1
Item No.
Description
00071689
00071690
00071691
00248311
00071699
00070973
00260212
3/8 HTN for use on 3/8" Kwik Bolt IIs at all embedment depths (1-5/8", 2-1/2", 4-1/4")
1/2 HTN-M for use on 1/2" Kwik Bolt IIs at minimum embedment depth (2-1/4")
1/2 HTN-SD for use on 1/2" Kwik Bolt IIs at standard embedment depth (3-1/2") or deeper
1/2 HTN-CSM Conical Sleeve Kwik Bolt IIs at standard embedment depth (3-1/2") or deeper
5/8 HTN-SD for use on 5/8" Kwik Bolt IIs at standard embedment depth (4") or deeper
HTN Removal Tool 3/8 (3/8" size HTN)
HTN Removal Tool 1/2, 5/8 (1/2" size HTN)
Torque required to set
Box Qty
23 ft-lb
40 ft-lb
65 ft-lb
65 ft-lb
110 ft-lb
50
50
50
50
50
1
1
1 See Product Technical Guide for complete performance data.
www.us.hilti.com
7.31
Medium Duty Anchor
Hilti Removable & Reusable Coil Anchors

The Only Truly Reusable Anchor for Temporary & Permanent Applications
Replacement Coil
HCAs utilize a
disposable low-cost
coil which keeps
reuse cost to a
minimum.
Depth Set Mark

HCAs have a clear depth set
mark on the shank of the anchor
that assists proper installation.
Hex Head
HCAs utilize a hex bolt head style that
enables low profile fastenings to be
made. Separate washer included.
Significant Cost Savings as result of
multiple-use design
Stud Type Anchor HCAs are stud type

anchors that make through-type fastenings
a snap.
Pre-Assembled HCAs are preassembled
units to keep production fastenings
moving quickly!
HCA Hex Head
Item No.
(Box)
Master
Carton#
(MC)
Description
00252000
00252002
00252003
00252004
00252005
00252007
00252010
00252011
00252012
00252013
00252014
00252015
00252016
00252017
00252018
00252019
339622
339623
339624
339625
339626
339628
339629
339630
339631
339632
339633
339634
339635
339636
339637
339638
HCA 1/4" X 1-3/4"

HCA 1/4" X 2-1/2"
HCA 1/4" X 3-1/2"
HCA 3/8" X 2-1/4"
HCA 3/8" X 3"
HCA 3/8" X 5"
HCA 1/2" X 3"
HCA 1/2" X 4"
HCA 1/2" X 5-1/2"
HCA 1/2" X 7"
HCA 5/8" X 3-1/2"
HCA 5/8" X 5"
HCA 5/8" X 8"
HCA 3/4" X 4-1/2"
HCA 3/4" X 6"
HCA 3/4" X 10"
Bit
dia
Min.
Emb
Depth
Max.
Fixture
Thickness
At Min.
Emb
Install
Torque
ft-lb
Ultimate Loads in
4000 psi Concrete1
Allowable Loads in
4000 psi Concrete1
Emb
Depth
Tension
(lb)
Shear
(lb)
Tension
(lb)
Shear
(lb)
Qty Box/
MC
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
2"
2-3/8"
2-3/8"
2-3/8"
3-1/4"
3-1/4"
3-1/4"
5/8"
1-3/8"
2-3/8"
1/8"
7/8"
2-7/8"
3/8"
1-3/8"
2-7/8"
4-3/8"
3/8"
1-7/8"
4-7/8"
1/4"
1-3/4"
5-3/4"
10
10
10
40
40
40
80
80
80
80
130
130
130
180
180
180
3/4"
1"
1"
1-1/2"
2"
2"
2"
3"
3"
3"
2-3/8"
3-7/8"
3-7/8"
3-1/4"
4-1/2"
4-1/2"
1305
2005
2005
3690
5675
5675
5675
10430
10430
10430
7345
15305
15305
11760
19160
19160
1315
2145
2145
4825
7615
7615
8575
13570
13570
13570
12305
21240
21240
22150
30590
30590
325
500
500
920
1420
1420
1420
2605
2605
2605
1835
3825
3825
2940
4790
4790
330
535
535
1205
1965
1965
2145
4270
4270
4270
3075
7070
7070
5540
9630
9630
100/1000
100/1000
100/600
100/500
100/500
50/250
50/250
50/250
25/125
25/125
25/125
25/100
20/80
20/80
10/40
10/40
HCT Replacement Coil

Item No.
(Box)
00255985
00255987
00255988
00255989
00255980
Master
Carton#
(MC)
Description
Qty
Box/MC
339639
339640
339641
339642
339643
HCT 1/4"
HCT 3/8"
HCT 1/2"
HCT 5/8"
HCT 3/4"
100/3000
100/2500
100/2000
50/1500
50/1000
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.32
Medium Duty Anchor

Listings/Approvals
Control No. 767G
HDI Flush-Mount Internal Thread Anchor

Meets Wide Range Fastener Requirements
FM (Factory Mutual)
Serial No. 22765

ER Report No. 2895 Seismic Data
Supplemental Pending

Report No. 9930

Report No. 23709

Specification
FF-S-325, Group VIII, Type 1
Applications
Materials
The HDI is an internally threaded metal anchor for medium load range
applications such as fastenings with bolts and threaded rods for plumbing,
heating, air-conditioning and ventilation installations, pipe suspension, air
ducts etc., for securing channels, rails, plates, brackets and suspended
ceilings
HDI Carbon Steel material meets

the requirements of AISI 1110M or
AISI 1010 for the 1/4", 3/8" and
1/2" HDIs and AISI 12L14 for the
5/8" and 3/4" HDIs.
HDI Stainless Steel material meets
the requirements of AISI 303.
Carbon Steel HDI plated with a dull
zinc finish for corrosion protection
in accordance with ASTM B633,
Sc. 1, Type III.
Features
Anchor, setting tool and Hilti drill bit form a matched tolerance system to
provide reliable fastening
Below surface setting for easy patchwork
Allows for shallow embedment without sacrificing performance
HDI Flush Mount Internal Thread Anchor

Carbon Steel
Item No.
(Box)
Master
Carton#
(MC)
Description
Bit
dia
Embed &
Anchor
Length
Useable
Thread
Length
Internal
Thread
Size
Ultimate Loads
4000 psi Concrete1
Tension (lb)
Shear (lb)
HDI 1/4"
HDI 3/8"
HDI 1/2"
HDI 5/8"
HDI 3/4"
3/8"
1/2"
5/8"
27/32"
1"
1"
1-9/16"
2"
2-9/16"
3-3/16"
7/16"
5/8"
11/16"
7/8"
1-3/8"
1/4"
3/8"
1/2"
5/8"
3/4"
2270
4460
7140
11685
16260
Master
Carton#
(MC)
Description
Bit
dia
Embed &
Anchor
Length
Useable
Thread
Length
Internal
Thread
Size
Ultimate Loads
4000 psi Concrete1
Tension (lb)
Shear (lb)
339617
339618
339619
339620
339621
HDI 1/4" (SS303)

HDI 3/8" (SS303)
HDI 1/2" (SS303)
HDI 5/8" (SS303)
HDI 3/4" (SS303)
3/8"
1/2"
5/8"
27/32"
1"
1"
1-9/16"
2"
2-9/16"
3-3/16"
7/16"
5/8"
11/16"
7/8"
1-3/8"
1/4"
3/8"
1/2"
5/8"
3/4"
1930
4170
7350
10540
15340
00045752 32366
00045753 32367
00045754 32368
00336428 258540
00336429 258541
Stainless Steel
Item No.
(Box)
00336430
00336431
00336432
00336433
00336434
2500
5000
8500
13000
20000
2400
4920
11040
18040
22320

4000 psi Concrete1
Tension (lb)
Shear (lb)
570
1115
1785
2920
4065
625
1250
2125
3250
5000

4000 psi Concrete1
Tension (lb)
Shear (lb)
480
1040
1840
2630
3830
600
1230
2760
4510
5580
Qty
Box/MC
100/1200
50/600
50/300
25/100
25/100
Qty
Box/MC
100/1200
50/600
50/300
25/100
25/100
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
arton
MasterallCets
&P
B e s t Va l
ue

HDI Setting Tools see page:
7.37
7.33
Medium Duty Anchor

Listings/Approvals
HDI-L Flush Drop-In Anchor

The Unsinkable, Awesome Anchor.
Control No. 767G
FM (Factory Mutual)
serial No. 22765

Specification
FF-S-325, Group VIII, Type 1
Applications
Features
The HDI-L is an internally threaded metal anchor for a

wide range of uses by virtually all trades.
Applications include: fastenings with bolts and threaded
rods for plumbing, heating, air-conditioning and
ventilation installations, pipe suspension, air ducts etc.,
for securing channels, rails, plates, brackets and
suspended ceilings
Lip provides flush installation, consistent anchor

depth, and easy rod alignment
Lip allows accurate flush surface setting, independent
of hole depth and ideal for repetitive fastenings with
threaded rods of equal length
Intelligent expansion sections adapts to the base
material and reduces number of hammer blows up to
50%
Easy to read brand and size identification (red laser
print)
HDI-L Flush Drop-in Anchor

Carbon Steel
Item No.
(Box)
Master
Carton#
(MC)
00247818 309429
00247817 309430
00247816 309431
Description
Bit
dia
Embed &
Anchor
Length
Useable
Thread
Length
Internal
Thread
Size
HDI-L 1/4"
HDI-L 3/8"
HDI-L 1/2"
3/8"
1/2"
5/8"
1"
1-9/16"
2"
7/16"
5/8"
11/16"
1/4"
3/8"
1/2"
Ultimate Loads
4000 psi Concrete1
Tension (lb)
Shear (lb)
2270
4460
7140
2500
5000
7750

4000 psi Concrete1
Tension (lb)
Shear (lb)
570
1115
1785
625
1250
1940
Qty
Box/MC
100/1200
50/600
50/300
Hilti Exclusive Intelligent Expansion Section

3/8" and 1/2" Sizes
Low-strength base material (fully set)
High-strength base material (fully set)
arton
MasterallCets
&P
B e s t Va l
ue

For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.37
7.34
Medium Duty Anchor

Listings/Approvals
FM (Factory Mutual)
HDI-P Drop-in Anchor

Reliable Fastenings in Pre-cast Hollow Core, Post-Tensioned and Poured Concrete
Report No. 5264

Report No. 25350
Technical Data
Materials
Anchor material is AISI 1010 or
AISI 1110M
Carbon steel anchor plating is dull
zinc, in accordance with ASTM
B633, SC.1, Type III
Features
The HDI-P Setting Tool System

leaves a mark on the flange when
the anchor has been fully set
increasing reliability of
installations.
Optimized 3/4" anchor length to allow reliable fastening

in hollow core panels, pre-cast plank and post tension slabs
Shallow drilling enables fast installation
Lip provides flush installation, consistent anchor depth,
and easy rod alignment
Setting tool leaves mark on flange when anchor is set properly
to aide inspection and ensure reliable installation
HDI-P Drop-in Anchor (exclusive anchor for Pre-Cast Hollow Core & Post-Tensioned)
Carbon Steel
Item No.
(Box)
Master
Carton#
(MC)
00243554 339616
Description
Bit
dia
Embed &
Anchor
Length
Useable
Thread
Length
Internal
Thread
Size
Ultimate Loads
4000 psi Concrete1
Tension (lb)
Shear (lb)

4000 psi Concrete1
Tension (lb)
Shear (lb)
HDI-P 3/8"
1/2"
3/4"
3/8"
3/8"
1900
3000
Hollow Core1
2100
4000
380
600
Hollow Core1
420
800
Qty
Box/MC
100/1200
arton
MasterallCets
P
&
B e s t Va l
For complete
Hilti Anchoring
Systems
technical
information:
ue

Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.37
7.35
Medium Duty Anchor

Materials
HDI-S Speed Thread Mechanical Anchor
Anchor material is carbon steel with

zinc plating
Reliable Fastenings in Normal Weight Concrete, Hardstone & Solid Block

for Coil Rod Applications
Features
Designed to accept coil rod, and used in combination with the standard
Hilti HDI setting tool and drill bits: the reliable HDI-S speed thread Drop-In
Anchor forms a matched tolerance system for your forming applications.
Ideal for temporary concrete forming application, i.e. bridge, highway,
tunnel and subway constructions and repair, the HDI-S can be used in
solid concrete, hard stone and solid block.
HDI-S Speed Thread Mechanical Anchor

Carbon Steel
Item No.
(Box)
Master
Carton#
(MC)
00336931 337858
00336932 337859
Description
Bit
dia
Embed &
Anchor
Length
HDI-S 1/2"
HDI-S 3/4"
5/8"
1"
2"
3-3/16"
Useable
Thread
Length
Internal
Thread
Size
11/16"
1/2" - 6 TPI
1-3/8" 3/4" - 4-1/2" TPI
Ultimate Loads
4000 psi Concrete
Tension (lb)
Shear (lb)
7140
16260
6280
14800

4000 psi Concrete
Tension (lb)
Shear (lb)
1785
4065
1570
3700
For complete
Hilti Anchoring
Systems
technical
information:
Qty
Box/MC
50/300
25/100
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.37
7.36
Medium Duty Anchor
Setting Tools for HDI Anchors

Hand Setting ToolStandard
Item No
Description
Sets Anchor Size
00032978
00032979
00032980
00032981
00032982
HST 1/4" Hand Setting Tool

1/4" HDI / HDI-L

3/8" HDI / HDI-L
1/2" HDI / HDI-L
5/8" HDI / HDIS
3/4" HDI / HDIS
Hand Setting Tool for HDI-P only

Item No
Description
00247776 HSD-G 3/8" to 3/4" Hand Setting Tool with hand guard
00253784 HST-P 3/8" to 3/4" Hand Setting Tool
Sets Anchor Size
HDI-P-3/8"
HDI-P-3/8"
Automatic Setting Tool (for TE15, TE18, TE25 drills)
Item No
Description
00243751 HSD-M M 3/8" (TE-C-24 SD 10-3/8" Setting Tool")

00243752 HSD-M M 1/2" (TE-C-24 SD 12-1/2" Setting Tool")
For complete
Hilti Anchoring
Systems
technical
information:
Sets Anchor Size
3/8" HDI / HDI-L

1/2" HDI / HDI-L
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.37
Medium Duty Anchor

Listings and Approvals
Versatile Hilti HLC Sleeve Anchor

Wide Variety Of Head Styles, Easy to Install
Listing (1/2" to 3/4")
For Fastening To Concrete, Masonry, Hollow Block or Grout-filled Block
HLC-H shown this page. Other versions available on following page.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Variety of head styles, lengths and sizes allow for

versatile applications
Comprehensive testing demonstrating high
performance in block, masonry and concrete base
materials
New bolt version with low profile head provides
aesthetically pleasing finish and increased safety
Features
Stud-type anchor design allows easy through-type
fastenings and can be set in bottomless hole
Pre-assembled anchor ensures easy and fast
installation
Anchor size is same as drill bit size
for easy installation
Anchor Program
HLC-H Sleeve Anchor, bolt version
Item No.
(Box)
00336244
00336245
00336252
00336253
00336259
00336260
00336261
Master
Carton#
(MC)
338090
338091
338098
338099
338105
338106
338107
Description
dbit/
dbit/anchor
dia (in.)
Lc
Anchor
Length (in.)
h1
Min. Drill
Depth (in.)
hmin
Min. Embed.
Depth (in.)
tfix
Max. Mat.
Fastened
HLC-H 5/16x1-5/8
HLC-H 5/16x2-5/8
HLC-H 3/8x1-7/8
HLC-H 3/8x3
HLC-H 1/2x2-1/4
HLC-H 1/2x3
HLC-H 1/2x4
5/16"
5/16"
3/8"
3/8"
1/2"
1/2"
1/2"
1-5/8"
2-5/8"
1-7/8"
3"
2-1/4"
3"
4"
1-3/8"
1-3/8"
1-3/4"
1-3/4"
2-1/8"
2-1/8"
2-1/8"
1"
1"
1-1/4"
1-1/4"
1-1/2"
1-1/2"
1-1/2"
5/8"
1-5/8"
5/8"
1-3/4"
3/4"
1-1/2"
2-1/2"
Load Values (lb)

4,000 psi Concrete1
Tension
Shear
Load Values (lb)

Hollow C-90 Block1
Tension
Shear

refer to the
Click
hereAmerican
for product
load2002
values.
Hilti North
Technical Guide,
Ed.,
Section 4.3.7
Qty
Box/MC
100/1200
100/600
50/600
50/450
50/400
25/225
25/225
304SS Sleeve Anchor (304SS)

Item No.
(Box)
Master
Carton#
(MC)
Description
dbit/
dbit dia
00015731
00015732
00015733
00015734
00015735
20752
20753
20754
20755
20756
Slv Anch HX 304 SS 1/4-2-1/4

Slv Anch HX 304 SS 5/16-1-1/2
Slv Anch HX 304 SS 5/16-2-1/2
Slv Anch HX 304 SS 3/8-1-7/8
Slv Anch HX 304 SS 3/8-3
1/4"
5/16"
5/16"
3/8"
3/8"
Lc
Anchor
Length
hmin
Min. Embed.
Depth
2-1/4"
1"
1-1/2"
1"
2-1/2"
1"
1-7/8" 1-1/4"
3"
1-1/4"
Thread
Size
(UNC)
tfix
Max. Mat.
Fastened
3/16"
1/4"
1/4"
5/16"
5/16"
1-1/4"
1/2"
1-1/2"
5/8"
1-3/4"
Ultimate Load Values

2000 psi Concrete1
2000 psi Concrete1
Tension (lb)
Shear (lb) Tension (lb) Shear (lb)
940
1240
1240
1800
1800
1800
2700
2700
4000
4000
235
310
310
450
450
Qty
Box/MC
450 100/1200
675 100/1200
675 100/1200
1000
50/
1000
50/
1 Based on average ultimate values obtained during testing performed by Hilti. We recommend a safety factor of at least 4:1.
7.38
Medium Duty Anchor
Hilti HLC Sleeve Anchor
Lc
For Fastening To Concrete, Masonry, Hollow Block or Grout-filled Block
HLC-H*
HLC-HX
HLC-FPH
HLC-T
HLC-AC
HLC-RS
HLC-RC
Anchor Program
HLC-HX Sleeve Anchor, stud version
Item No.
(Box)
Master
Carton#
(MC)
Description
Bit Dia (in.)
00336242 338088 HLC-HX 5/16x1-5/8 5/16"

00336243 338089 HLC-HX 5/16x2-5/8 5/16"
00336246 338092 HLC-HX 3/8x1-7/8
3/8"
00336247 338093 HLC-HX 3/8x3
3/8"
00336255 338101 HLC-HX 1/2x2-1/4
1/2"
00336256 338102 HLC-HX 1/2x3
1/2"
00336257 338103 HLC-HX 1/2x4
1/2"
00336258 338104 HLC-HX 1/2x6
1/2"
00336263 338109 HLC-HX 5/8x2-1/4
5/8"
00336264 338110 HLC-HX 5/8x4-1/4
5/8"
00336265 338111 HLC-HX 5/8x6
5/8"
00336266 338112 HLC-HX 3/4x2-1/2
3/4"
00336267 338113 HLC-HX 3/4x4-1/4
3/4"
00336268 338114 HLC-HX 3/4x6-1/4
3/4"
HLC-FPH Sleeve Anchor, flat head version
00336234 338080 HLC-FPH 1/4x1-3/8 1/4"
00336235 338081 HLC-FPH 1/4x2
1/4"
00336236 338082 HLC-FPH 1/4x3
1/4"
00336237 338083 HLC-FPH 1/4x4
1/4"
00336248 338094 HLC-FPH 3/8x2-7/8 3/8"
00336249 338095 HLC-FPH 3/8x4
3/8"
00336250 338096 HLC-FPH 3/8x5
3/8"
00336251 338097 HLC-FPH 3/8x6
3/8"
HLC-T Sleeve Anchor, tie-wire version
00336241 338087 HLC-T 1/4x1-3/8
1/4"
HLC-AC Sleeve Anchor, acorn nut version
00336232 338078 HLC-AC 1/4x1-3/8 1/4"
00336233 338079 HLC-AC 1/4x2-1/4 1/4"
HLC-RS Sleeve Anchor, round head version
00336238 338084 HLC-RS 1/4x1-1/4 1/4"
00336239 338085 HLC-RS 1/4x2
1/4"
00336240 338086 HLC-RS 1/4x4
1/4"
HLC-RC Sleeve Anchor, rod coupler version
00336254 338100 HLC-RC 3/8x1-7/8
3/8"
00336262 338108 HLC-RC 1/2x2-1/4
1/2"
00251966 369429 SLV ANC RC 5/8 x 2-1/4 5/8"
Lc
Anchor
Length (in.)
h1
Min. Drill
Depth (in.)
hmin
Min. Embed.
Depth (in.)
tfix
Max. Mat.
Fastened (in.)
Load Values (lb)

4,000 psi Concrete1
Tension
Shear
Load Values (lb)

Hollow C-90 Block1
Tension
Shear
1-5/8"
2-5/8"
1-7/8"
3"
2-1/4"
3"
4"
6"
2-1/4"
4-1/4"
6"
2-1/4"
4-1/4"
6-1/4"
1-3/8"
1-3/8"
1-3/4"
1-3/4"
2-1/8"
2-1/8"
2-1/8"
2-5/8"
2-5/8"
2-5/8"
2-5/8"
2-5/8"
2-5/8"
2-5/8"
1"
1"
1-1/4"
1-1/4"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
2"
2"
2"
5/8"
1-5/8"
5/8"
1-3/4"
3/4"
1-1/2"
2-1/2"
4-1/2"
1/4"
2-1/4"
4"
1/2"
2-1/4"
4-1/4"
1-3/8"
2"
3"
4"
2-7/8"
4"
5"
6"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/4"
1-3/4"
1-3/4"
1-3/4"
1"
1"
1"
1"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
3/8"
1"
2"
3"
1-5/8"
2-3/4"
3-3/4"
4-3/4"
1-3/8"
1-3/8"
1"
50/600
1-3/8"
2-1/4"
1-3/8"
1-3/8"
1"
1"
3/8"
1-1/4"
100/1800
100/1200
1-1/4"
2"
4"
1-3/8"
1-3/8"
1-3/8"
1"
1"
1"
1/4"
1"
3"
100/1800
100/1800
100/1200
1-7/8"
2-1/4"
2-1/4"
1-3/4"
2-1/8"
2-5/8"
1-1/4"
1-1/2"
2"
50/400
25/225
25/75
Qty
Box/MC
100/1200
100/900
50/600
50/450
50/400
25/225
25/225
15/135
10/120
10/120
10/120
10/80
10/60
10/60
Click

refer to the
Technical Guide,
2002 Ed.,
here forSection
product
4.3.7 load
values.
100/2400
100/2400
100/1600
100/1200
50/600
50/400
50/400
25/300
1 Based on average ultimate values obtained during testing performed by Hilti. We recommend a safety factor of at least 4:1.
* HLC-H ordering information on previous page.
7.39
Light Duty Anchor
KWIK-CON II+ Masonry Screw Anchor System

Tri-Lobular Design Yields Higher Shear and Tensile Values, Cuts Stronger Threads
Thread Forming Lobes
Relief Areas
Hilti's advanced KWIK-CON II+ Masonry Screw Anchor

System, with its unique tri-lobular design, provides superior
fastening performance in concrete, cement block, brick,
masonry or stone.
Developed for a wide range of fastening applications, the
self-tapping screw anchor system is ideal for use by
electricians, general contractors, glaziers and maintenance
technicians.
The improved KWIK-CON II+ system features a more
compact setting tool and requires no bit adapter, making
masonry screw anchoring faster and easier than ever
before. The tri-lobular thread-cutting design and larger
cross section of KWIK-CON II+ screws improve thread
engagement and provide greater shear values and tensile
strengths than competitive products.
Select sizes of stainless steel are also available.
Hole Diameter
Determining Correct
Fastener and Hole Depth
The KWIK-CON II+ masonry
fastening system consist of the
KWIK-CON II+ drive tool and a
matched tolerance carbide-tipped
drill bit. Consistent performance and
maximum pullout strength are
attained when all system elements
are used properly.
KWIK-CON II+ fasteners come in
three diameters: 1/4", 3/16" and
3/8". Fastener diameter and
embedment depth affect pullout
strengths. Application strength
requirements and safety factors
should be considered when
determining the embedment depth
and fastener diameter.
Fastener Length (A+B)
Hole Diameter
The length of the KWIK-CON II+

fastener to be used is determined by
combining the thickness of the
fixture being attached (A) with the
desired depth of embedment in the
masonry material (B). It is
recommended that a minimum of
1" and a maximum of 1-3/4"
embedment be used in determining
fastener length.
The diameter of the drilled hole is

also important to the performance of
the KWIK-CON II+ masonry fastening
system. Use Hilti matched tolerance
carbide-tipped bits to obtain
consistent fastener performance and
maximum pullout strength.
C
1/2"minimum
Hole Depth (B+C)

A matched tolerance carbide-tipped
drill bit is supplied with each combo
box of KWIK-CON II+ fasteners. In all
cases, the hole must be at least 1/2"
(C) deeper than the depth of the
fastener embedment. Normal safety
precautions should be observed
when drilling holes to avoid electrical
or other utility installations and
reinforcement bars.
A = Fixture Being Attached

B = KWIK-CON II+ Embedment
(minimum 1", maximum of 1-3/4"
recommended)
A+B = Length of KWIK-CON II+
recommended for application
B+C = Depth of Hole Drilled
(must be at least 1/2" deeper than
KWIK-CON II+ embedment)
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.40
Light Duty Anchor
KWIK-CON II+ Matched Tolerance Masonry Fastening System

Matched Tolerance System Provides The Highest Performance
Features
Choice of head styles: Torx Hex
Washer Head for fast, secure
driving; Torx or Phillips Flat Head
for countersinking applications
Matched tolerance carbide-tipped
drill bits for highest performance
The Kwik-CON II+ fastening system is

convenient to use. Simply insert the
carbide-tipped SDS+ or TM bit directly
into the rotary hammer. No special
adapters are needed.
Exclusive internal torx drive

Choice of 1/4" or 3/16" diameter
fasteners
Fasteners protected by corrosion
resistant coating; stainless steel
fasteners available in select sizes
Drill a hole 1/2" deeper than the

required screw penetration.
For individual item description,

see ordering information listed below.
Change the rotary hammer setting to

rotation only. Lock the compact setting
tool over the special detent receiver on
the bit.
Adjust the depth location and set the

screw.
Its that easy.
KWIK-CON II+ Hex Driver System

KWIK-CON II+ Matched Tolerance Drill Bits*
Item No.
Description
* For 3/16" diameter KWIK-CON use small bits. for 1/4" diameter KWIK-CON use large bits.
00235097
KWIK-CON Hex Driver Deluxe Kit
Item No.
Description
00205114
00205116
00205118
00205120
TKC Large Concrete Bit SDS+ HEX

TKB Large Block Bit SDS+ HEX
TKC Small Concrete Bit SDS+ HEX
TKB Small Block Bit SDS+ HEX
Bit Marking
1/4 C
1/4 B
3/16 C
3/16 B
00205115
00205117
00205119
00205121
00205322
TKC Large Concrete Bit TM+ HEX

TKB Large Block Bit TM+ HEX
TKC Small Concrete Bit TM+ HEX
TKB Small Block Bit TM+ HEX
TE-C+ 8.5 mm x 17 mm for 3/8" KWIK-CON
1/4 C
1/4 B
3/16 C
3/16 B
Item No.
Driver System Individual Components
00235100
00235098
00235101
00083313
KWIK-CON 5/16" Hex setter/depth locator

KWIK-CON hex driver
KWIK-CON insert bit holder/depth locator
5/16" Hex Driver - KC II+
Shown above right
00083312
#3 Phillips Driver - KC II+
For All THWH without depth setting
00083314
T-25 Torxalign Driver Short
For use with all 3/16" TFH / THWH + 1/4" THWH
T-27 Torxalign Driver Short

7.41
For use with all PFH
00087123
www.us.hilti.com
00369306
00084209
00084213
T-25 Torxalign Long

T-27 Torxalign Long
For use with all 3/8" TPH
er &
Fasten
l
Dril Bit
Light Duty Anchor
Combo
KWIK-CON II+ Fasteners
Available
Matched Tolerance System Provides The Highest Performance

Setting Tool: 5/16" Hex Driver (00083313) or T-25 Torx Bit Align Driver (Short 00083314 / Long 00084209)
Item No.
(Box)
00219915
00219916
00219917
00219918
00219919
00219920
00219921
Combo #
W/ Bit
Master
Carton # (MC)
00256009
00256010
00256011
00256012
00256013
00256014
00256015
00220590
00220591
00339503
00220592
00339504
00339505
00339506
QtyBox/
MC
Total
Length
Description
Diameter
KWIK-CON II+ 316-114 THWH

3/16" 100/1000 1-1/4"

3/16" 100/1000 1-3/4"
3/16" 100/1000 2-1/4"
3/16"
100
2-3/4"
3/16"
100
3-1/4"
3/16"
100
3-3/4"
3/16"
100
4"
Setting Tool: 5/16" Hex Driver (00083313) or T-25 Torx Bit Align Driver (Short 00083314 / Long 00084209)
Item No.
(Box)
00219906
00219907
00219908
00219909
00219910
00219911
00219912
00219913
00219914
Combo #
W/ Bit
Master
Carton # (MC)
00256016
00256017
00256018
00256019
00256020
00256021
00256022
00256051
00256052
00220593
00220594
00339507
00220595
00339508
00220596
00339509
00335059
00235060
Diameter
QtyBox/
MC
Total
Length
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
100
100
100
100
100
100
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
4"
1-1/4"
2-3/4"
Description
Diameter
QtyBox/
MC
Total
Length
KWIK-CON II+ 316-114 TFH

3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
100
100
100
100
100
100
100
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
4"
Diameter
QtyBox/
MC
Total
Length
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
100
100
100
100
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
4"
Description
Diameter
QtyBox/
MC
Total
Length
KWIK-CON II+ 316-114 PFH

KWIK-CON II+ 316 x 334 PFH
KWIK-CON II+ 316-114 PFH Stainless Steel
KWIK-CON II+ 316-234 PFH Stainless Steel
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
100
100
100
100
100
100
100
100
100
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
4"
1-1/4"
2-3/4"
Diameter
QtyBox/
MC
Total
Length
Description

KWIK-CON II+ 14-114 THWH Stainless Steel
KWIK-CON II+ 14-234 THWH Stainless Steel
Setting Tool: T-25 Torxalign Driver Bit (Short 00083314 / Long 00084209)
Item No.
(Box)
00219896
00219897
00219898
00219899
00219900
00219901
00219902
Combo #
W/ Bit
Master
Carton # (MC)
00256023
00256024
00256025
00256026
00256027
00256028
00256029
00339510
00220597
00339511
00220548
00339512
00220599
00339513
Setting Tool: T-27 Torxalign Driver Bit (Short 00087123 / Long 00084213)
Item No.
(Box)
00219886
00219887
00219888
00219889
00219890
00219891
00219892
Combo #
W/ Bit
Master
Carton # (MC)
00256030
00256031
00256032
00256033
00256034
00256035
00256036
00339514
00219953
00339515
00339516
00219954
00339517
00339518
Description

Setting Tool: #3 Phillips Driver (00083312)

Item No.
(Box)
00219924
00219925
00219926
00219927
00219928
00219929
00219930
00219931
00219932
Combo #
W/ Bit
Master
Carton # (MC)
00256037
00256038
00256039
00256040
00256041
00256042
00256043
00256053
00256054
00339519
00219955
00339520
00219956
00339521
00339522
00339523
00235058
00235061
Setting Tool: #3 Phillips Driver (00083312)

Item No.
(Box)
00219934
00219935
00219936
00219937
00219938
00219939
00219940
Combo #
W/ Bit
Master
Carton # (MC)
00256044
00256045
00256046
00256047
00256048
00256049
00256050
00339524
00219957
00339525
00219958
00339526
00339527
00339528
Description

1/4"
100
1/4"
100
1/4"
100
1/4"
100
1/4"
100
1/4" 100/1000
1/4" 100/1000
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
4"
www.us.hilti.com
7.42
Light Duty Anchor
Performance Data KWIK-CON II+ Masonry Fastening System

Ultimate Loads (lb)
Ultimate Tensile and Shear Strength in Concrete1
Anchor
Diameter
Embedment
Depth
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
2000 psi
Tension
Shear
4000 psi
Tension
Shear
6000 psi
Tension
Shear
400
1100
760
1700
500
1180
970
2500
750
1300
1100
2600
1050
1050
1300
2250
1050
1070
1575
2550
1150
1200
2175
2400
Ultimate Tensile and Shear Strength in Hollow Block*1

Anchor
Embedment
Diameter
Depth
Tension
Shear
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
595
1160
660
1235
895
1200
1100
1605
Ultimate Tensile and Shear Strength in Red Brick Guide Values1

Anchor
Embedment
Diameter
Depth
Tension
Shear
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
510
1740
825
1405
950
1205
1660
1995
This test was performed on individual specimens of ASTM

C62 common red brick. Due to the wide variations
encountered in the compressive strength of brick, these
values should be considered to be guide values.
Allowable Loads (lb)

Allowable Tensile and Shear Strength in Concrete1 Allowable Loads**
Anchor
Diameter
Embedment
Depth
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
2000 psi
Tension
Shear
100
275
190
425
260
260
325
560
4000 psi
Tension
Shear
125
295
240
625
260
265
390
635
6000 psi
Tension
Shear
185
325
275
650
280
300
540
600
Allowable Tensile and Shear Strength in Hollow Block*1 Allowable Loads**

Anchor
Diameter
Embedment
Depth
Tension
Shear
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
150
290
165
310
225
300
275
400
Allowable Tensile and Shear Strength in Red Brick Guide Values1 Allowable Loads**
Anchor
Embedment
Diameter
Depth
Tension
Shear
3/16"
3/16"
1/4"
1/4"
1"
1-3/4"
1"
1-3/4"
125
435
205
350
235
300
415
500
This test was performed on individual specimens of ASTM

C62 common red brick. Due to the wide variations
encountered in the compressive strength of brick, these
values should be considered to be guide values.
* ASTM Specification C90 Grade N, Type II Pilot holes drilled with TKB matched tolerance bits for concrete blocks.
** Allowable working loads are based on a safety factor of 4 to 1.
1 Published load values represent the average test results of testing conducted in local base materials using Hilti matched-tolerance drill bits. Because of
variations in materials, on-site testing is necessary to determine actual performance at any specific site.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.43
Light Duty Anchor

The Complete TapCon System Now Available from Hilti
NEW!
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@@@
;;;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
@@@@@@@@@@@@
@@@@@@@@@@@@
;;;;;;;;;;;;
@@@@@@@@@@@@
;;;;;;;;;;;;
1/4" minimum
Hilti saves you time and money by offering a total TapCon

System with matched tolerance drill bits and a
comprehensive installation kit for quick and easy anchor
installation.
Hilti TapCon anchors are stalgard corrosion protected
masonry fasteners available in both Hex head and
Phillips flat head style in 3/16" and 1/4" anchor
diameters. For optimum performance, anchors must be
installed using the matched tolerance drill bits available
as part of the TapCon System.
TapCon anchors can be set in concrete, hollow brick and
red brick and represent excellent value-to-performance
as complimentary anchors to the extensive Hilti KWIKCon selection.
Features & Benefits

3/16" and 1/4" anchor diameters, with additional
sizes available by special order
Available in Hex head and Phillips Flat head styles

Stalgard coating with improved corrosion resistance
Nail point improves anchor guidance into pre-drilled
hole for smooth and safe installation
Removable for temporary fastening
Save time with the comprehensive TapCon Deluxe
Driver Installation Kit designed to work with drill bits in
placeno need to remove the drill bit to set the
anchor
Installation kit contains all required toolsno
searching for additional setting tools
Hex Driver has fitted magnet for easy anchor
installation and recessed head designed to ensure
torque control during installation
Matched tolerance drill bits in straight-shank, SDS
and HEX design
A = Fixture Being Attached

B = TapCon Embedment
A+B = Length of TapCon
recommended for application
B+C = Depth of Hole Drilled
(must be at least 1/4" deeper than
TapCon embedment)
Performance Data TapCon Masonry Fastening System

Allowable Loads (lb)
Allowable Tensile and Shear Loads in Concrete(Note 1, 3, and 4)
Anchor Diameter
3/16"
1/4"
Embedment Depth
Tension (lb)
Shear (lb)
1"
1-3/4"
1"
120
225
120
150
150
285
Embedment Depth
Tension (lb)
Shear (lb)
1-1/4"
1-1/4"
80
175
140
320
Allowable Tensile and Shear Loads in Hollow Brick(Note 2 and 3 )

Anchor Diameter
3/16"
1/4"
Because of variations in materials, on-site testing is necessary to determine actual performance at any specific site
Notes
1. Concrete Strength tested is 2,925 psi and results published are relevant only to this Concrete Strength
2. Hollow Block Strength tested is 1500 psi and results published are relevant only to this Hollow Block Strength
3. Allowable loads are based on a safety factor of 5 to 1 applied to the average ultimate test values
4. Load Values represent the results of testing when installing TapCon Anchors using Hilti SDS & HEX Drill Bits
Tension Load Values only: Reduce these Values by 50 % for applications in Concrete with no reduction for applications in Hollow Block if using
straight-shank drill bit's supplied inside the TapCon box.
www.us.hilti.com
7.44
Medium Duty Anchor

The Complete TapCon System Now Available from Hilti
Item No. (Box)
Master Carton # (MC)
00377212
00377213
00377218
00377210
00377211
00377355
00377356
00377357
00377358
00377359
Description
Qty/Box
Qty/MC
Anchor Diameter
Drill Diameter
Anchor Length
Setting Tool
TapCon 1/4 x 1-1/4 SHWH

100
100
100
100
100
1000
1000
1000
1000
1000
1/4"
1/4"
1/4"
1/4"
1/4"
3/16"
3/16"
3/16"
3/16"
3/16"
1-1/4"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
5/16" Hex Driver

5/16" Hex Driver
5/16" Hex Driver
5/16" Hex Driver
5/16" Hex Driver
Note: 1 Carbide Tipped straight-shank Drill Bit is supplied with every box of 100 TapCon Anchors
Item No. (Box)
Master Carton # (MC)
00377220
00377223
00377215
00377217
00377222
00377219
00377224
00377216
00377221
00377214
00377360
00377361
00377362
00377363
00377364
00377365
00377366
00377367
00377368
00377369
Description
Qty/Box
Qty/MC
Anchor Diameter
Drill Diameter
Anchor Length
Setting Tool
TapCon 3/16 x 1 3/4 PFH

TapCon 1/4 x 1-1/4 PFH
TapCon 1/4 x 4 PFH
100
100
100
100
100
100
100
100
100
100
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
3/16"
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
5/32"
5/32"
5/32"
5/32"
5/32"
3/16"
3/16"
3/16"
3/16"
3/16"
1-3/4"
2-1/4"
2-3/4"
3-1/4"
3-3/4"
1-1/4"
1-3/4"
2-3/4"
3-1/4"
4"
#2 Phillips Bit
#2 Phillips Bit
#2 Phillips Bit
#2 Phillips Bit
#2 Phillips Bit
#3 Phillips Bit
#3 Phillips Bit
#3 Phillips Bit
#3 Phillips Bit
#3 Phillips Bit
Note: 1 Carbide Tipped straight-shank Drill Bit is supplied with every box of 100 TapCon Anchors
Installation Tool
Comprehensive system specially designed TapCon Driver Deluxe Kit contains all the tools required for easy and quick
installation of TapCon anchors. All TapCon Systems tools are designed to work in conjunction with both straightshanked and SDS/HEX drill bits while using a rotary hammer with "Jacobs" chuck or SDS chuck and SDS drill bit.
Drills need not be removed for installation of TapCon anchors saving you time and installation costs.
Item No.
Description
00377370
TapCon Driver Deluxe Installation Kit

1each: straight-shank drill adapter, Phillips #2 bit, Phillips #3 bit, Phillips driver adapter, 1/4" magnetic
Hex driver, 5/16" magnetic Hex driver, drive sleeve assembly and 1/8" Hex keyDrill Bits
Drill Bits
TapCon straight-shank or SDS/HEX drill bit can remain in place with driver tool fitting over drill bit no removal of
drill required for installation of TapCon anchors saving time and reducing installation costs.
TapCon Straight-shank Drill Bits
Designed specifically to work either with a standard "Jacobs" chuck or together with the TapCon Driver Deluxe Kit. Straightshank drill adapter included. Carbide-tipped drill bit included in every TapCon box of 100 pieces.
Item No. (Tube)
Description
00377691
00377692
00377693
00377694
TapCon 5/32 x 3 1/2 straight-shank Drill Bit

Qty / tube
10
10
10
10
Max. Drilling Depth
TapCon Size
2 1/4"
4 1/4"
2 1/4"
4 1/4"
3/16"
3/16"
1/4"
1/4"
TapCon SDS and HEX Drill Bits

Carbide tipped SDS and HEX drill bit specifically designed to work with rotary hammer drills.Drill must be in rotary-only mode
during TapCon anchor installation.
Item No. (Tube)
Description
00377695
00377696
00377697
00377698
TapCon 5/32 x 5 SDS & HEX Drill Bit

Qty / tube
1
1
1
1
Max. Drilling Depth
TapCon Size
2 1/4"
4 1/4"
2 1/4"
4 1/4"
3/16"
3/16"
1/4"
1/4"
www.us.hilti.com
7.45
Light Duty Anchor
Hilti Metal HIT Anchor

Fast, Easy Installation; Low Profile Appearance
Features
Quick and easy fastening for maximum speed and installation

Low profile mushroom head style provides a nice finish and tamper proof fastening
Anchor design allows easy through-type fastenings even in bottomless holes
Consistent load values provide safe light duty fastenings in concrete and masonry
Choice of Stainless Steel or Carbon Steel nail allows for indoor or outdoor use
Metal HIT Anchor Program

Item No.
(Box)
Master
Carton#
(MC)
Description
00066137
00015538
00066138
00066139
00066140
00045453
00230567
00230568
00230569
00230570
20679
20680
20681
20682
20683
20684
308495
308496
308497
308498
Metal HIT 3/16 x 7/8

3/16"
Metal HIT 1/4 x 3/4
1/4"
Metal HIT 1/4 x 1
1/4"
Metal HIT 1/4 x 1-1/4
1/4"
Metal HIT 1/4 x 1-1/2
1/4"
Metal HIT 1/4 x 2
1/4"
Metal HIT w/SS Nail2 1/4 x 1
1/4"
Metal HIT w/SS Nail2 1/4 x 1-1/4 1/4"
Metal HIT w/SS Nail2 1/4 x 1-1/2 1/4"
Metal HIT w/SS Nail2 1/4 x 2
1/4"
Bit
dia
Anchor
Length
Embed
Depth
(min)
7/8"
3/4"
1"
1-1/4"
1-1/2"
2"
1"
1-1/4"
1-1/2"
2"
5/8
5/8
3/4
1
1
1
3/4
1
1
1
2000 psi Concrete

Tension
Shear
Load Values (lb)1

Hollow Block
Tension
Shear
Red Clay Brick

Tension
Shear

contact your Hilti Field Engineer.
Qty
Box/MC
100/2000
100/1000
100/1000
100/1000
100/1000
100/1000
100/1000
100/1000
100/1000
100/1000
1 Contact your Hilti Field Engineer for allowable design values.

2 304 Stainless Steel Nail.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.46
Light Duty Anchor
Hilti HPS-1 Impact Anchor

Fast Installation For Permanent Or Temporary Fastenings In Brick, Block And Concrete
Features
Phillips drive connection is recessed in the screw head providing
protection during hammering, allowing simple setting and removal
Anchor collar and screw head form a compact unit which allow
countersinking in soft wood and solid clamping action with metal parts
Expanding head opens in hollow base material to provide reliable keying
effect
One type anchor reduces inventory, providing versatile use in brick, hollow
block and concrete
Can be set with hammer or screw driver for quick and easy installation
Available with 304 stainless steel nail for corrosive environments
Suitable for through-hole fastenings to improve productivity
Plastic body is temperature resistant from 40F to 176F. Anchor can
be installed from +14F to 104F. Both features allow use in extreme
climatic conditions.
Removability adds to HPS-1 versatility
Carbon Steel
Item No.
(Box)
00260347
00260348
00260368
00260344
00260345
00260346
00260353
00260354
00260355
00260356
Stainless Steel
00260357
00260358
00230520
00230521
00230522
00230523
00260365
00260366
Master
Carton#
(MC)
Description
Bit
dia
Anchor
Length
Fastenable Material Thickness

in Hollow
in Concrete
Base Materials
(max)
(max)
Qty
Box/MC
247053
247054
247055
247056
247057
247058
247059
247060
247061
247062
HPS-1 3/16 X 1
HPS-1 3/16 X 1-1/2
HPS-1 1/4 X 1
HPS-1 1/4 X 1-5/8
HPS-1 1/4 X 2-1/16
HPS-1 1/4 X 2-5/8
HPS-1 5/16 X 1-5/8
HPS-1 5/16 X 2-1/2
HPS-1 5/16 X 3-5/8
HPS-1 5/16 X 4-3/8
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
5/16"
5/16"
5/16"
5/16"
1"
1-1/2"
1"
1-5/8"
2-1/16"
2-5/8"
1-5/8"
2-1/2"
3-5/8"
4-3/8"
3/16"
5/8"
1/8"
5/8"
1"
1-5/8"
3/8"
1-3/16"
2-3/8"
3-1/8"
3/8"
3/4"
3/16"
3/4"
1-3/16"
1-3/4"
5/8"
1-3/8"
N/A
N/A
200/2400
200/2400
200/2400
100/900
100/900
100/900
100/900
75/600
50/600
50/600
246935
246936
246937
246938
246939
246940
246943
246944
HPS-1 R 3/16 X 1
HPS-1 R 3/16 X 1-1/2
HPS-1 R 1/4 X 1
HPS-1 R 1/4 X 1-5/8
HPS-1 R 1/4 X 2-1/16
HPS-1 R 1/4 X 2-5/8
HPS-1 R 5/16 X 3-5/8
HPS-1 R 5/16 X 4 3/8
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
5/16"
5/16"
1"
1-1/2"
1"
1-5/8"
2-1/16"
2-5/8"
3-5/8"
4-3/8"
3/16"
5/8"
1/8"
5/8"
1"
1-5/8"
2-3/8"
3-1/8"
3/8"
3/4"
3/16"
3/4"
1-3/16"
1-3/4"
N/A
N/A
200/2400
200/2400
200/2400
100/900
100/900
100/900
50/600
50/600
HPS-1 Allowable Working Loads (lb) Guide Values*

Base Material
Concrete 2000 psi

Brick Masonry
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
Hollow Concrete Block (Normal Wt.)

Minimum Embed Depth Concrete
Minimum Embed Depth Hollow Base
Tensile
Shear
Tensile
Shear
Tensile
Shear
3/16" X 1"
3/16" X 1-1/2"
30
95
35
105
50
120
3/4"
5/8"
1/4" X 1"
1/4" X 1-5/8"
1/4" X 2-1/16"
1/4" X 2-5/8"
5/16" X 1-5/8"
5/16" X 2-1/2"
5/16" X 3-5/8"
5/16" X 4-3/8"
55
130
40
145
55
140
7/8"
13/16"
70
135
45
165
60
160
1"
13/16"
80
215
45
220
65
185
1-3/16"
1"
90
110
N/A
N/A
N/A
N/A
1-3/16"
N/A
* Based upon a safety factor of 5.
www.us.hilti.com
7.47
Light Duty Anchor
Hilti Toggler Bolt Hollow Wall Anchor

Specifically Designed for Hollow Wall Applications
3/16" & 1/4"
3/8" & 1/2"
Features
Unique installation legs and locking cap facilitate fastenings in wide
range of drywall and hollow wall materials up to 2-1/4" thick
One piece zinc plated carbon steel channel provides greater holding
power
Anchor is adjustable for various base material thicknesses for easier
installation as well as minimum inventory investment
Remains mounted in the wall without screw for convenient handling,
installation and re-use
Comprehensive offering with and without machine screws
Toggler Bolt Anchor Program
Item No.
(Box)
00374497
00374493
00374494
00374499
00374495
00374496
Item No.
(Box)
00066365
00066366
00066370
00066371
Master
Carton#
(MC)
Description
00374498
00374489
00374490
00374500
00374491
00374492
Master
Carton#
(MC)
20673
20674
20677
20678
Bit
dia
Togglerbolt II 3/16" W/PFH Screw

Togglerbolt II 3/16" W/SRH Screw
Togglerbolt II 1/4" W/SRH Screw
Togglerbolt II 1/4" W/PFH Screw
Togglerbolt II 3/16" W/O Screw
Togglerbolt II 1/4" W/O Screw
Description
Toggler Bolt 3/8 with Screw

Toggler Bolt 1/2 with Screw
Toggler Bolt 3/8 without Screw
Toggler Bolt 1/2 without Screw
Bolt
Size
1/2" 3/16"
1/2" 3/16"
1/2" 1/4"
1/2" 1/4"
1/2" 3/16"
1/2" 1/4"
Bolt
Length
2-1/2"
2-1/2"
2-1/2"
2-1/2"
Bit
dia
Bolt
Size
Bolt
Length
3/4"
3/4"
3/4"
3/4"
3/8"
1/2"
3/8"
1/2"
2-1/2"
2-1/2"
1/2" Drywall
Tension
Shear
30
30
35
35
*
*
70
70
85
85
*
*
1/2" Drywall
Tension
Shear
35
35
*
*
70
85
*
*
Allowable Loads (lb.)1

5/8" Drywall
Tension
Shear
45
45
50
50
*
*
95
95
105
105
*
*
Allowable Loads (lb.)1

5/8" Drywall
Tension
Shear
50
50
*
*
105
110
*
*
Tension
Block
Shear
Qty
Box/MC
140
140
160
160
*
*
160
160
240
240
*
*
100/500
100/500
100/500
100/500
100/500
100/500
Tension
Shear
Qty
Box/MC
200
240
*
*
380
420
*
*
25/250
25/250
25/250
25/250
Block
1 Based on a safety factor of 4.

* Contact your Hilti Engineer for load values.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.48
Light Duty Anchor
Hilti KwikTog
Unique One-Piece Design for Use in Sheet Rock, Block or Concrete
Features
Unique one-piece design for easy setting
Three convenient sizes for use in a variety of hollow base materials from
1/4" drywall to block and concrete
Leg braces provide added support
Ribs on body help prevent anchor from spinning during installation
Remains mounted in the wall without screw for convenient handling,
installation and reuse
KwikTog Anchor Program

Item No.
(Box)
00063581
00063582
00063583
Master
Carton#
(MC)
20668
20669
20670
Bit
diameter
Description
KwikTog 2 (HLD2)
KwikTog 3 (HLD3)
KwikTog 4 (HLD4)
3/8"
3/8"
3/8"
Recommended Screw Size

Hollow
Solid
Base Mat
Base Mat
#8 or #10
#8 or #10
#8 or #10
#10
#10
#10
Hollow Base
Material
Thickness
Allowable*
Loads in 5/8" Drywall
Tension (lb)
Qty
Box/MC
3/16" to 5/8"
5/8" to 7/8"
15/16" to 1-1/4"
25
35
100/1000
50/500
50/500
* Based on a safety factor of 5.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
-eAr
0
8
1
F
SCordless Driv
e5
see pag
.8

www.us.hilti.com
7.49
Light Duty Anchor
Hilti HSP/HFP Light-Duty Drywall Anchor

The Anchor With Powerful Front Teeth
Cuts Its Own Thread, Quick and Easy Fastening To Drywall Panels
The zinc HSP (Hilti Speed Plug) and glass fibre reinforced polyamide HFP (Hilti
Fiber Plug) are ideal for light-duty fastenings on drywall panels. One bit that
fits both anchor and screw allows a fast and easy setting process.
Features
Exceptional versatility
Sharks tooth design for correct

positioning and quick installation
Cuts its own thread
One Hilti bit for anchor and
screw. No setting tool required.
Hilti HSP also available with 1/4"
male connecting thread
HSP and HFP delivered with or
without screws
HSP
Item No.
(Box)
00332682
00332683
00332686
00332687
00332688
Master
Carton No.
(MC)
00333979
00333980
00333982
00333983
-
Bathroom accessories
Light fixtures
Picture frames
Signs
Shelving
Mirrors
Junction boxes
Conduit
Curtain rods
Anchor
Description
Anchor
length
(in.)
Screw
diameter
Qty
Box/MC
HSP
HSP-S (Delivered with 100 screws, # 8 x 1-3/16")
HFP
HFP-S (Delivered with 100 screws, # 8 x 1" )
D-B PH2 HSP/HFP Phillips Head Bit
1-1/2
1-1/2
1-1/8
1-1/8
-
#8
#8
#8
#8
-
100/1600
100/1600
100/1600
100/1600
5
*For complete Load Values, refer to the Hilti North American Technical Guide, 2002 Ed., Section 4.13.14.
HSP-S
+
HFP
HFP-S
+
Phillips Head Bit for HSP and
HFP (D-B PH2 HSP/HFP)
-eAr
0
5
1
F
SCordless Driv
e 5.7
see pag
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.50
Light Duty Anchor
Hilti HUD-1 And HUD-L

Light-Duty Universal Plastic Anchors
Engineered For Universal Use In Attaching Fixtures To Wide Variety Of Base Materials
Hollow Brick
Aerated Concrete
Double-Panelled Drywall 2 x 1/2"

Not recommended for single
panel drywall application.
Use HSP/HFP or Toggler bolt
(pages 7.50, 7.48).
HUD-1
HUD-L
Light-duty universal plastic anchor

Fastening wood furring strips, junction boxes, cable clips,
light switches, light fixtures, brackets, signs, shelves,
bathroom fixtures, and much more.
Extra long universal plastic anchor

Special plastic anchor for new & renovation applications;
fastening through thick materials e.g. plaster; stucco
applied to concrete, block, brick base materials
Base Materials
Base materials
Hollow and solid brick masonry with plaster layers

up to 1-3/16"
Concrete with plaster layers up to 1-3/16"
Double-panelled drywall (2 x 1/2" thick)
Aerated concrete
Hollow & solid concrete block (cmu)
Hollow & solid brick

Hollow & solid concrete block (cmu)
Concrete
Aerated concrete
HUD-1/HUD-L Features
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
Precisely controlled screw guidance prevents wandering and keeps the screw within the anchor shank
Four-way expanding head: Enhances keying effect in hollow base material
Anti-rotation wings help prevent the anchor from rotating and falling out during installation
High-grade nylon material: contains no halogen and no heavy metals, resistant in temperatures from 40 F to 176 F
HUD-1: Flared collar: makes the anchor suitable for pre-installation or installation through fixtures, e.g. junction box
HUD-L: No collar: suitable for installation through fixtures
HUD-1: Forms a keying knot when installed in hollow material. 1/4" and 5/16"
diameter sizes are preferred recommendation.
HUD-L: Forms a keying knot when installed in hollow material and in double panelled drywall. 1/4" and 5/16"
diameter sizes are preferred recommendation for these applications.
HUD-1 Universal Plastic Anchor

Item No.
Description
00331615 HUD-1 3/16 x 1 without screws

00336483 HUD-1 3/16 x 1 with #8 x 1-1/2 combo screw,
TM masonry drill bit and #2 Phillips bit in
2-compartment plastic box
00336484 HUD-1 3/16 x 1 with #8 x 1-1/2 combo screw
00331616 HUD-1 1/4 x 1-3/16 without screws
00336485 HUD-1 1/4 x 1-3/16 with #10 x 1-1/2 combo screw,
TM masonry drill bit and #2 Phillips bit in
2-compartment plastic box
00336486 HUD-1 1/4 x 1-3/16 with #10 x 1-1/2 combo screw
00336487 HUD-1 5/16 x 1-5/8 with 1/4 x 2-1/2 combo screw
00331618 HUD-1 3/8 x 2 without screws
00336488 HUD-1 3/8 x 2 with 5/16 x 2-1/2 combo screw
00336489 HUD-1 1/2 x 2-3/8 with 3/8 x 3 combo screw
00336490 HUD-1 9/16 x 2-3/4 with 1/2 x 3-1/2 combo screw
HUD-L Universal Plastic Anchor
7.51
Head
Style
Outside dia (in.) =

nom. bit dia
Min hole
depth (in.)
Anchor length (in.)
Screw
Size (in.)
Box/Bag
Qty
-Pan Head
3/16
3/16
1-3/8
1-3/8
1
1
#8
#8
500
100
Pan Head
Pan Head
3/16
1/4
1/4
1-3/8
1-5/8
1-5/8
1
1-3/16
1-3/16
#8
#10
#10
500
500
100
Pan Head
-Hex Head Lag Screw
-Hex Head Lag Screw
-Hex Head Lag Screw
-Hex Head Lag Screw
1/4
5/16
5/16
3/8
3/8
1/2
1/2
9/16
9/16
1-5/8
2-3/16
2-3/16
2-5/8
2-5/8
3-1/8
3-1/8
3-1/2
3-1/2
1-3/16
1-5/8
1-5/8
2
2
2-3/8
2-3/8
2-3/4
2-3/4
#10
1/4
1/4
5/16
5/16
3/8
3/8
1/2
1/2
500
400
400
200
200
100
100
50
50
Head
Style
Outside dia (in.) =

nom. bit dia
Min hole
depth (in.)
Anchor length (in.)
Screw
Size (in.)
Box/Bag
Qty
Item No.
Description
00315938
00336491
00315939
00336487
00315940
00336488
HUD-L 1/4 x 2 without screws

-1/4
2-3/4
2
#10
400
HUD-L 1/4 x 2 with #10 x 2-1/2 combo screw
Pan Head
1/4
2-3/4
2
#10
400
HUD-L 5/16 x 2-3/8 without screws
-5/16
3-1/8
2-3/8
1/4
200
HUD-L 5/16 x 2-3/8 with 1/4 x 2-1/2 combo screw
Hex Head Lag Screw
5/16
3-1/8
2-3/8
1/4
200
HUD-L 3/8 x 2-3/4 without screws
-3/8
3-1/2
2-3/4
5/16
100
HUD-L 3/8 x 2-3/4 with 5/16 x 3-1/2 combo screw
Hex Head Lag Screw
3/8
3-1/2
2-3/4
5/16
100
Specialty Light Duty Anchor
IDP Insulation Anchor

Fast, Easy Installation
Features
Specially structured head to help ensure bonding of plaster applied directly over the
anchor
Suitable for insulation thickness up to 4-3/4" for enhanced versatility
Installation in concrete and masonry allow versatile use
No metal parts which reduces potential condensation behind finish coat of EIF
systems
Item No.
(Box)
Description
Bit
Diameter
Anchor
Length
Minimum
Embedment
Insulation
Thickness
00332105
00332106
00332107
00332108
00332109
00332110
IDP 0/2
IDP 2/4
IDP 4/6
IDP 6/8
IDP 8/10
IDP 10/12
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
2"
2-3/4"
3-1/2"
4-1/4"
5"
6"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
to 7/8"
7/8 to 1-3/4"
1-3/4" to 2-3/8"
2-3/8 to 3-1/8"
3-1/8 to 4"
4 to 4-3/4"
Average Ultimate Pullout (lb)3

Hollow
Concrete
Block2
Brick
Concrete1
110
110
110
110
110
110
45
45
45
45
45
45
55
55
55
55
55
55
Box Qty
250
250
250
250
250
250
1 Concrete Strength fc = 2500 psi

2 Hollow Concrete Block meets ASTM SPEC C90, Grade N, Type II
3 Pullout values may be limited by the strength of the material fastened.
For complete
Hilti Anchoring
Systems
technical
information:
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.52
Light Duty Anchor Kit Box

All Your Light Duty Anchor Needs In One Box
Features
One box with anchors for a wide range of base materials

A compact unit to move from job to jobno loose parts
The potential to customize the box after the initial purchase
The opportunity to use new product without purchasing box quantities
Additional Light Duty Anchor Information:

Product
HLC Sleeve Anchor

Metal HIT**
HPS-1**
HUD-1
HSP/HFP
KWIK Tog
Toggler Bolt
Diameter Range
Length Range
Bit Diameter
1/4" to 3/4"
3/16" to 1/4"
3/16" to 5/16"
3/16" to 9/16"
3/8"
3/16" to 1/2"
1-3/8" to 6-1/4
7/8" to 2"
1" to 4-3/8"
1" to 2-3/4"
1" to 1-5/16"
3/16" to 1-1/4"
3/8" to 3-3/4"
1/4" to 3/4"
3/16" to 1/4"
3/16" to 5/16"
3/16" to 9/16"
3/8"
1/2" to 3/4"
**Also available in 304 stainless steel
HLC Sleeve Anchors
Metal HIT
HPS-1
For complete
Hilti Anchoring
Systems
technical
information:
Typical Application
Information
Concrete
Solid Brick
Hollow Block
Stone
Hollow Brick
Solid Block
Lockers
Door Frames
Plumbing
Partitions
Piping
Signs
Handrails
Cabinets
Duct Work
Concrete
Stone
Hollow Brick
Solid Brick
Hollow Block
Conduit
Control Boxes
Drywall Track
TV Cables
Lighting
Window Grating
Concrete
Solid Brick
Hollow Block
Stone
Hollow Brick
2X4s
Signs
Chalkboards
Alarms
Furring Strips
Unistrut
Headboards
Controls
Drywall Track
HUD-1
Concrete
Stone
Hollow Brick Block
Solid Brick
Aerated Concrete
Signs
J Boxes
Pictures
Mirrors
Conduits
Clocks
HSP/HFP
Drywall
Signs
Pictures
Mirrors
Phone/TV Cables
Bathroom Fixtures
Window Coverings
KWIK TOG
Drywall
Hollow Brick
Hollow Block
Signs
Mirrors
Lighting Fixtures
Window Coverings
TOGGLER BOLT
Hollow Block
Drywall
Drain Pipes
Lockers
2X4s
Outdoor Lighting
Bathroom Partition
Refer to the
Hilti North
America Product
Technical Guide
www.us.hilti.com
7.53

for Light Duty Anchors
Item No
Description
00234984
Light Duty Anchor Kit Box
00376175
Light Duty Anchor Kit Box and Insert Only (empty)
Kit includes anchors listed above
Split Bolt
Item No.
Description
Bit Diam
Length
96248205
96248206
96248207
96248208
96248209
96248210
96248211
96248212
96248213
96248214
1/4 X 1-1/2 FH SPLIT BOLT

1/4 X 2 FH SPLIT BOLT
1/4 X 1-1/4 RH SPLIT BOLT
1/4 X 2 RH SPLIT BOLT
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1 1/2"
2"
2-1/2"
3"
3-1/2"
4"
1-1/4"
1-1/2"
2"
2-1/2"
Stock Status
2D
2D
2D
2D
2D
2D
2D
2D
2D
2D
Head Styles:
FH: Flat Head
RH: Round Head
Expansion Shields
Double
Expansion
Shield
Single
Expansion
Shield
Item No.
Description
Bit Diam
Length
96248215
96248216
96248217
96248218
96248219
96248220
1/4 SINGLE EXPANSION SHIELD

1/2"
5/8"
5/8"
7/8"
1"
1-1/4"
1-5/16"
1-1/2"
1-1/2"
2-1/16"
2-5/8"
2-3/4"
Stock Status
Item No.
Description
Bit Diam
Length
96248221
96248222
96248223
96248224
96248225
96248226
1/4 DOUBLE EXPANSION SHIELD

1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
1-1/16"
1-1/8"
1-9/16"
1-7/8"
2"
3"
2D
2D
2D
2D
2D
2D
Stock Status
2D
2D
2D
2D
2D
2D
Lag Shields
Item No.
Description
Bit Diam
Length
96248231
96248232
96248233
96248234
96248227
96248228
96248229
96248230
1/4 LAG SHIELD-LONG

5/16 LAG SHIELD-LONG
3/8 LAG SHIELD-LONG
1/2 LAG SHIELD-LONG
1/4 LAG SHIELD-SHORT
1/2"
1/2"
5/8"
3/4"
1/2"
1/2"
5/8"
3/4"
1-1/2"
1-3/4"
2-1/2"
3"
1"
1-1/4"
1-3/4"
2"
Stock Status
2D
2D
2D
2D
2D
2D
2D
2D
Stock Status:
2D 2 business days plus shipping
from East Coast typical
www.us.hilti.com
7.54
So many parts...
...so little time.

NEW
Pre-Assembled 90 Angle
Strut Program
Strut
Fasteners
Angles & Connectors
Clamps
Bases
Accessories
Strut Clamps
Seismic Bracing
Page 8.7
Page 8.10
Page 8.12
Page 8.18
Page 8.19
Page 8.21
Page 8.23
Page 8.25
Hanger Program
Hangers
Riser Clamps
Pipe Straps
Beam Clamps
Accessories
Page 8.26
Page 8.30
Page 8.31
Page 8.32
Page 8.34
Installation Systems Data

Load Data
Pipe Data
Page 8.40
Page 8.46
Technical Resources
Hilti North America Technical Guide
Tech Center www.us.hilti.com
The Components Of Your New Installation System

Strut
C-profile with serrated edges for
greater hold and adjustability
Scaled tick marks every 2" to

assist with measurement, cutting,
and installation
Slots for greater flexibility

Longitudinal swaging for greater
strength
Back to Back Strut

Self-riveting process provides
consistent channel to channel
fastening over spot welding
Slotted back to back profile
Integrity of galvanized coating is
maintained
Saddle Nut
A single part, easy to use and time saving

Pleasing appearance
Compatible with C-profile strut types
Accommodates 1/4", 3/8", 1/2"
and 5/8" threaded rod
www.us.hilti.com
8.3
Hilti Installation Systems

Less Time = Less Cost, More Profit
Pushbutton
The MQN Pushbutton is the main tie between
connector and strut
Simple and universal one MQN Pushbutton
fits all Hilti strut types
One part replaces a spring nut, bolt and washer
Removeable and reusable
NEW!
Connectors
Only a few connectors necessary for all applications
Used together, connector and Pushbutton
save time and make installation work easier
Preassembeled 90 Angle
Its so simple: press, turn and lock its fastened
Dismantling the installation, if necessary, is just as easy
NEW!
Case Study #1402* Electrical Supervisor
ADDED
VALUE
$12,576 annual labor savings using Hilti Installation

Systems to build customer shut-off box brackets versus
welding brackets made of angle iron.
www.us.hilti.com
8.4
Save Time And Money With Hilti Kwik Cuts!

Very often the short length needed for an application is not 10' or 20' but only 2', 4' or 6'
Save the time of cutting strut
and get the convenient Hilti Kwik
Cuts. Available in pre-cut
lengths of 2', 4' and 6',
pre-galvanized and green.
Easy handling and storage
No measuring
No cutting
Clean factory edge
ADDED
VALUE
Case Study Top*

Construction Supervisor

savings using Hilti
Installation Systems to
hang conduit and pipe
versus welding
trapezes made of angle
iron in-place and then
threading pipe and
conduit through welded
trapezes.
* For complete details, contact Hilti.

Actual results may vary.
2' Kwik Cut

4' Kwik Cut
6' Kwik Cut
10' Hilti Strut
20' Hilti Strut
www.us.hilti.com
8.5
Installation Systems Table of Contents

Strut Program
HS installation
channels/strut
Brackets
Angle Brace
MQN Pushbutton
MKN-FX Pushbutton
page 8.9
page 8.9
page 8.10
page 8.10
MQW-Q2
Pre-Assembled
90 Angle
Angles
Angles
page 8.14
page 8.15
page 8.7
3D System
page 8.12
Angle
Brackets
45
page 8.15
page 8.13
MQA Saddle Nut
MQM-F Strut Nut
page 8.11
page 8.11
Connector,
Two
Dimensional
Connector,
Three
Dimensional
page 8.16
page 8.16
Splices
Splices
Clamps
Strut Bases
Pivot Base
Base Plates
Strut Tie
page 8.17
page 8.17
page 8.18
page 8.19
page 8.20
page 8.21
page 8.21
MEK Strut End Cap
Beam Clamp
Assembly
(BC-A)
Strut Beam clamp

(SBC)
Spring Nut (SNA)
Channel Nut
page 8.22
page 8.22
Strut Clamp
Copper-Plated
(STCC)
Strut Clamp
Rigid (STCR)
page 8.21
page 8.22
page 8.22
page 8.23
page 8.23
Strut Clamp
EMT
(STC-EMT)
Strut Clamp
Universal
(STC-UNIV)
Cushion
Clamps &
Inserts
page 8.23
page 8.23
page 8.24
Concrete Insert Strut Steel Concrete Spot

Insert
page 8.24
Nut for Concrete

Spot Insert
Seismic Hinge
page 8.25
page 8.24
page 8.24
Split ring: electro

galvanized/copperplated
Riser clamps (RC)
Pipe Straps, Clamps
page 8.30
page 8.31
Bolts, nuts and

washers
Rod couplers
Internal & external

rod stiffeners
page 8.25
Hanger Program
Speed lock clevis
(SLC)
page 8.26
Standard duty clevis Insulation shield

hanger: electropage 8.27
galvanized
(SDC-EG)
Loop hangers
(LH)
page 8.28
page 8.29
page 8.27
Beam clamps
(BC)
Steel C-clamp
with lock nut
page 8.32
page 8.33
U-bolts
page 8.36
Retainer straps
Threaded Rod
Eye couplers
page 8.33
page 8.34
page 8.34
page 8.35
page 8.35
brackets
8.37
Strut technical
information
Wall plates
8.37
pages 8.398.45
Lag bolts/screws
8.38
Also Available: Side beam
Pipe Data: pages 8.468.47

Cast iron
Glass pipe
PVC plastic tube
Copper tube
Steel pipe
www.us.hilti.com
8.6
Strut
Hilti Strut
Material:
C-profile with serrated edges
Scale to assist
installation/assembly/
measurement
Slots for greater flexibility
Longitudinal swaging for greater
strength
Hilti Self-Riveted Back-to-Back Strut

Features
Self-riveting process provides consistently superior channel-to-channel fastening over spot welding
Integrity of galvanized coating is maintained in self-riveting process
9/16" x 1-9/16" slots, allow up to 1/2" threaded rod to pass through back-to-back strut without drilling
C-profile with serrated edges
Scale imprinted on strut to assist in measuring, cutting, assembly and installation
Material/Finishes
PG = Pre-Galvanized
Pre-galvanized (PG)
Pre-galvanized strut is manufactured using material produced by passing carbon steel sheets through a molten zinc
bath in a process known as hot-dip mill galvanization. The material conforms to ASTM A653 GR 33 with a zinc
thickness of G90 or 0.9 ounces of zinc per square foot. The channel is formed and slots are punched after the hot-dip
process hence the name pre-galvanized strut. Surfaces of the punched and cut portions are somewhat protected by
the adjacent zinc plating which acts as a sacrificial anode impeding corrosion of the raw edges.
Electro-Deposition Coating
GR E-Coat = Green
Electro-Deposition Coating or "E-Coating" uses electricity to deposit a smooth, thin, uniform layer of plastic coating on
the surface of the steel channel. The epoxy-coated strut is then cured in an oven at approximately 400C for at least
20 minutes. Salt spray (fog) testing has been conducted to verify the performance of the finishthe plastic coating
was tested 600 hours in a salt spray chamber, in accordance with ASTM B117-95 specification. Since the coating is
applied as a liquid, the epoxy travels into crevices and trouble spaces so that outside moisture is less able to invade
the coated area and cause corrosion.
www.us.hilti.com
8.7
Strut
Hilti Strut 12 Gauge

HS-13/16" 12 gauge
Item No.
Description
Hole Configuration
00309919
00309920
00312949
HS-1316-12/PG 10'
HS-1316-12/PG 20'
HS-1316-12/PGS 10'
Full Slot
Full Slot
Solid
Bundle Qty
50
50
50
Weight/Piece (lb)
12.2
24.3
15.4
HS-13/16" 12 gauge back to back

Item No.
Description
Hole Configuration
00247902
MS-21D 10'
1-9/16" x 9/16"
Bundle Qty
25
Weight/Piece (lb)
23.0
HS-1 5/8" 12 gauge

Item No.
Description
Hole Configuration
00309935
00309936
00309937
00309938
00338906
00309939
00309949
00309950
00373441
00373442
HS-158-12/PG 2'
HS-158-12/PG 4'
HS-158-12/PG 6'
HS-158-12/PG 10'
HS-158-12/PG 10'
HS-158-12/PG 20'
HS-158-12/PGS 10'
HS-158-12/PGS 20'
HS-158-12/GR E-Coat 10'
HS-158-12/GR E-coat 20'
Full Slot
Full Slot
Full Slot
Full Slot
2-5/8" x 11/16"
Full Slot
Solid
Solid
Full Slot
Full Slot
Bundle Qty
50
50
50
50
50
50
50
50
50
50
Weight/Piece (lb)
3.6
7.2
10.8
18.0
18.0
36.0
18.5
37.0
18.0
36.0
HS-1 5/8" 12 gauge back to back

Item No.
Description
Hole Configuration
00247903
MS-41D 10'
1-9/16" x 9/16"
Bundle Qty
25
Weight/Piece (lb)
35.9
HS-2 7/16" 12 gauge

Item No.
Description
Hole Configuration
00309965
00309966
HS-2716-12/PG 10'
HS-2716-12/PG 20'
Full Slot
Full Slot
Bundle Qty
40
40
Weight/Piece (lb)
24.5
49.0
Hilti Strut 14 Gauge

HS-13/16" 14 gauge
Item No.
Description
Hole Configuration
00309911
00309912
00373434
HS-1316-14/PG 10'
HS-1316-14/PG 20'
HS-1316-14/GR E-coat 10'
Full Slot
Full Slot
Full Slot
Bundle Qty
50
50
50
Weight/Piece (lb)
8.7
17.4
8.7
HS-1 5/8" 14 gauge

Item No.
Description
Hole Configuration
00309927
00309928
HS-158-14/PG 10'
HS-158-14/PG 20'
Full Slot
Full Slot
Bundle Qty
50
50
Weight/Piece (lb)
13.6
27.2
www.us.hilti.com
Beam Loading Table
see page:
8.40
8.8
Strut
Technical Data
Material
Brackets
Carbon steel
Finish
Electro-galvanized
Features
1/ "
4
Serrated C-section
Installation assisted by dimension
marking
Great flexibility due to slots
Back-to-back brackets welded all
around
11-13/16" , 17-11/16"
13/16" x 9/16"
3-1/8"
4-15/16"
2"
5/ "
16
11-13/16" , 17-11/16"
23-5/8"
13/ " x 9/ "
16
16
3-1/8"
4-15/16"
2"
Strut Length
(in.)
3/8"
17-11/16" , 23-5/8"
13/16" x 9/16"
4-3/4"
6-1/2"
2-3/8"
5/ "
16
Item No.
Description
00369607
00369608
00370595
00370597
00369616
00369617
00369619
MQK-21/300
MQK-21/450
MQK-41/3/300
MQK-41/3/600
MQK-72/600
MQK-21D/300
MQK-21D/600
Strut Length
(mm)
Strut Section
(gauge/mm)
300
450
300
600
600
300
600
14 / 2
14 / 2
12 / 3
12 / 3
12 / 2.75
14 / 2
14 / 2
A
(in./mm)
H
(in./mm)
L
(in./mm)
Box Qty
14"/355
25"/635
13"/328
20-7/8"/528
12-13/16"/324 45
20-1/2"/524
45
10
10
11-13/16"
17-11/16"
11-13/16"
23-5/8"
23-5/8"
11-13/16"
23-5/8"
Weight/Piece
(lb)
1.48
1.96
2.62
4.54
6.90
2.76
4.83
Box Qty
1
1
1
1
1
1
1
11-13/16" , 17-11/16"
23-5/8"
13/16" x 9/16"
3-1/8"
4-15/16"
2"
Angle Brace
Technical Data
Material
Carbon steel
Finish
Item No.
Description
Electro-galvanized
00369622
00369621
MQK-SK
MQK-SL
Material width
Angle brace, short

Angle brace, long
1-9/16" (40 mm)
Material thickness
3/16" or 1/8" (4 or 3 mm)
2-15/16"
7/16"
1-5/16"
9/16"
www.us.hilti.com
Bracket Loading Table
see page:
8.44
8.9
Fasteners
Fasteners
Replace a spring nut, bolt and washer with only one item . . . the Hilti Pushbutton!
Technical Data
Material
Carbon steel
Finish
Electro-galvanized
Features
Simple, compact, time saving

Single part
Easy to use
Universal: one and the same nut
for all struts
Simple removal
Item
MQN
MKN-FX
Allowable Loads2
Tension (lb)
Shear (lb)1
Zrec
Qrec
14 ga 12 ga
1125 1800
1125
N/A 2000
1500
Tightening
Torque
MD (ft-lb)
30
50
1 Shear loading applies to a single fastening and using Hilti strut.

Loads apply when used with Hilti serrated strut.
The value for MQN double fastening is 2025 lb.
The value for MKN-FX double fastening is 2400 lb.
2 Based on a safety factor of 2.2. Contact Hilti for loading information
when using Hilti Pushbuttons, MKN-FX or MQN in non-serrated strut
profiles.
NEW!
MQN Pushbutton
Item No.
Description
Weight/Piece
(lb)
Box Qty
00369623
MQN
0.145
50
Put in position.
Press and turn.
Tighten.
MKN-FX Pushbutton
Features:
For heavy duty applications
Fantastic time, labor and cost savings
A single part which can be pre-fitted
Item No.
Description
Box Qty
00337697
MKN-FX
25
Case Study # 2438* Project Manager
K
IC
CL

using oneADDED savings
piece Hilti MKN-FX
VALUE Pushbutton over traditional fastening method
using spring nuts, bolts
and washers.
www.us.hilti.com
8.10
Fasteners
Technical Data
Material
MQA-F Saddle Nut
Carbon steel
Finish
Features:
Electro-galvanized
A single part for simple, timesaving installation

For all types of channels
Trapeze application:
1. Secure threaded rod to ceiling.
2. Thread hex nut & saddle nut onto
threaded rod.
3. Hold strut in place and simply
twist saddle nut into strut.
4. Tighten hex nut.
1/4"
3/ "
8
1/2"
5/8"
Item No.
Description
Connection
Thread
Weight/Piece
(lb)
Box Qty
00377884
00377885
00377886
00377887
MQA-F 1/4"
MQA-F 3/8"
MQA-F 1/2"
MQA-F 5/8"
1/4"
3/8"
1/2"
5/8"
0.194
0.192
0.183
0.185
50
50
50
50
Item
MQA-F
MQA-F
MQA-F
MQA-F
1/4"
3/8"
1/2"
5/8"
Rec. Load1
Tension
Zrec (lb)
14 ga
Tightening
Torque
MD (ft-lb)
12 ga
600
1125
1125
1125
600
1500
1800
2100
7
15
30
30
1 Based on a safety factor or 2.2
Technical Data
Material
MQM-F Strut Nut
Carbon steel
Rec. Loads1
Tension
Shear
Zrec (lb)
Qrec (lb)
Item
14 ga 12 ga
MQM-F 1/4" 600 600
450
MQM-F 1/4" 1125 1500
1000
MQM-F 1/4" 1125 1500
1125
Finish
Electro-galvanized
1/4"
3/8"
1/2"
Tightening
Torque
MD (ft-lb)
7
15
30
Features:
Alternative to spring nut

Functions in shallow, standard and deep strut
Eliminates stocking of spring nuts for each depth of strut
Fast, easy installation
1 Based on a safety factor or 2.2
Item No.
Description
00377881
00377882
00377883
MQM-F 1/4"
MQM-F 3/8"
MQM-F 1/2"
Connection
Thread
1/4"
3/8"
1/2"
Weight/Piece
(lb)
Box Qty
0.077
0.075
0.073
50
50
50
www.us.hilti.com
8.11
Angles and Connectors
3D System
Technical data
Material
NEW!
Features
Carbon steel
Material thickness
Universal: few parts for all

applications
For installation of angles or
connectors on-site
Quick and easy to use
45 angle and bracing with
predetermined bending point
3/ "
4
1-3/8"
Item No.
Description
00369694
00369695
00369696
00369697
MQ3D-B 3D Base Connector

MQ3D-W90 3D 90 Connector
MQ3D-W45 3D 45 Connector
MQ3D-A 3D Threaded Rod Brace
1/8" (3 mm)
Finish
Electro-galvanized
Tightening torque
30 ft-lb (40 Nm)
3/ "
4
3/ "
8
3-9/16"
Weight/Piece
(lb)
Box Qty
0.454
0.467
0.337
0.209
20
20
16
20
7/ "
8
2-3/8"
Supported at both ends
Frec = 560 Ib
(2.5 kN)
Example of application
Frec Qrec MQN
with MQ3D-B
1"
Tension/compression bracing
ds
Frec = 560 Ib (2.5 kN)

th
bo
at
d
pp
or
te
Frec Qrec MQN

with MQ3D-B
Su
1-15/16"
en
Variable angle
45
Directly to strut
1-3/16"
Frec Qrec MQM-F3/8"

fastened to strut with
MQZ-L3/8" base plate
3/8"-1" (min.) hex. bolt
MQM-F3/8" strut nut
Frec = 560 Ib
(2.5 kN)
Variable angle
Tension bracing
Frec = 560 Ib (2.5 kN)

Frec Qrec MQN
with MQ3D-B
1-15/16"
Variable
angle
45
See Note
1"
Directly to strut
Frec Qrec MQM-F3/8"
Note: The pre-assem- fastened to strut with

Frec = 560 Ib
MQZ-L / " base plate
bled bolt may be re(2.5 kN)
/ "-1" (min.) hex. bolt
Variable angle
MQM-F / " strut nut
moved and replaced
with an anchor or
longer 3/8" bolt when
mounting to surface
other than the 3D Base Connector. All recommended
loads are based on a safety factor of 2.2.
3
See Note
See Note
www.us.hilti.com
8.12

Technical Data
Material
MQW-Q2 Pre-assembled 90 Angle
Carbon steel
Finish
Features
Electro-galvanized
Tightening torque
Single item 90 connection

Fits all Hilti Strut
Utilizes pushbutton technology
NEW!
30 ft-lb
Material thickness
1/8"
Advantages
Width across flats

11/16"
Reduces inventory costs

No parts to lose
Lightening fast installation
Item No.
Description
Weight/Piece
(lb)
Box Qty
00369655
MQW-Q2 90 Angle
0.441
20
Frec
900 Ib (4.0 kN)
Frec based on safety factor of 2.2
2-3/16"
2-3/16"
Press and turn.
Tighten.
* Loads apply when used with Hilti serrated strut. Use with non-serrated strut may result
in a significant reduction in load capacity. Contact Hilti for details.
www.us.hilti.com
8.13

Technical Data
Material
Carbon steel
Material thickness
3/16" (4 mm)
Features
Finish

applications
Easy to use
Three-dimensional, thus high
strength
Electro-galvanized
Opening dimensions:
Three Hole 90 Angle
Frec 1.8 x Qrec of

Single MQN pushbutton A
Features:
3- hole angle for Pushbuttons
4-3/8"
Item No.
Description
Weight/Piece (lb)
00369656
MQW-3
0.353
Box Qty
2-3/8"
20
Four Hole 90 Angle
Frec Qrec
(MQN A )
Features:
2-3/16"

90 angle
Replace left and right hole single corner connector
Item No.
Description
Weight/Piece (lb)
00369658
MQW-4
0.485
Box Qty
10
Eight Hole 90 Angle
Frec 1.8 x Qrec of

Single MQN pushbutton A
Features:
4-1/8"

90 angle
Item No.
Description
Weight/Piece (lb)
00369659
MQW-8/90
0.926
Box Qty
10
Three Hole 45 Angle

Features:
Compression: Frec 1685 Ib (7.5 kN)

Tension: Frec 1350 Ib (6.0 kN)
4-3/16"
(double bolted A )
45
Item No.
Description
Weight/Piece (lb)
00369657
MQW-3/45
0.342
Box Qty
2-3/16"
20
www.us.hilti.com
8.14

Eight Hole 45 Angle
Frec
1350 Ib (6.0 kN)
(double bolted A )
4-1/8"
Features:

45

Item No.
Description
Weight/Piece (lb)
00369660
MQW-8/45
0.904
Box Qty
10
Two Hole 45 Angle
3-15/16"
Features:
Compression: Frec = 1010 lb/4.5kN

Tension: Frec = 340 lb/1.5kN

45
Item No.
Description
Weight/Piece (lb)
00369662
MQW-2/45
0.780
Box Qty
10
3-15/16"
Single Brace Angle Bracket
4-5/16"
Frec = 450 Ib (2.0 kN)
Features:
4-5/8"
Two-dimensional bracket for Pushbuttons

For heavy wall/ceiling attachment to strut or base material
6-1/8"
Item No.
Description
Weight/Piece (lb)
00369664
MQW-S/1
1.014
4-5/8"
Box Qty
Frec based on safety

factor of 2.2
10
9/ "
16
Double Brace Angle Bracket
Frec = 900 Ib (4.0 kN)
7-7/8"
Features:
3-15/16"
4-hole angle for Pushbuttons

For heavy wall/ceiling attachment to strut or base material
7-7/8"
Item No.
Description
Weight/Piece (lb)
00369665
MQW-S/2
2.602
Box Qty
10
3-15/16"
Frec based on safety

factor of 2.2
9/ "
16
www.us.hilti.com
8.15

MQV-2/2D Connector
6-1/2"
Features:
Two-dimensional double connector for Pushbuttons
4-7/16"
Item No.
Description
Weight/Piece (lb)
00369638
MQV-2/2D
0.966
Box Qty
10
MQV-3/2D Connector
6-1/2"
Features:
Three-dimensional double connector for Pushbuttons
Item No.
Description
Weight/Piece (lb)
00369640
MQW-3/2D
1.356
Box Qty
4-7/16"
10
MV-3/2D X Connector
10-1/4"
Features:
6-11/16"
Three-dimensional heavy-duty double connector for Pushbuttons

Item No.
Description
Weight/Piece (lb)
00339590
MV-3/2D X
3.245
Box Qty
10
2"
2-3/16"
MQV-3/3D Connector
Features:
Three-dimensional double connector for MKN-FX Pushbutton
Item No.
Description
Weight/Piece (lb)
00369641
MQV-3/3D
0.994
Box Qty
4-7/16"
10
MQV-4/3D Connector
2-3/16"
Features:
Three-dimensional double connector for MKN-FX Pushbutton
Item No.
Description
Weight/Piece (lb)
00369642
MQV-4/3D
1.698
Box Qty
10
MQV-12 Connector
4-7/16"
8-1/16"
Features:
1-3/4"
Connector for HS-158 and HS-2716 strut for Pushbuttons

Item No.
Description
Weight/Piece (lb)
00369643
MQV-12
1.224
Box Qty
10
www.us.hilti.com
8.16

Four Hole Splice Plate
8-1/16"
Features:
Splice plate for Pushbuttons
Item No.
Description
Weight/Piece (lb)
00369644
MQV-P4
0.415
Box Qty
10
Two Hole Tee Splice Plate
1-7/8"
Features:
Item No.
Description
Weight/Piece (lb)
00370630
MQV-P2
0.22
Box Qty
10
3-3/4"
1-5/8"
Four Hole Tee Splice Plate

Features:
Item No.
Description
Weight/Piece (lb)
00369645
MQV-T
0.432
Box Qty
10
Three Hole Cross Splice Plate

Features:
Item No.
Description
Weight/Piece (lb)
00370629
MQV-P3
0.309
Box Qty
10
Five Hole Cross Splice Plate

Features:
Item No.
Description
Weight/Piece (lb)
00370631
MQV-P5
0.309
Box Qty
10
www.us.hilti.com
8.17
Clamps
Technical Data
Material
Clamps
Carbon steel
Material thickness
Features
3/16" (4 mm)

applications
Easy to use
Electro-galvanized
Finish
3/ "
4
1-3/8"
MQB-21 Clamp
3/ "
4
3/ "
8
6-5/16"
Features:
4-3/16"
3-hole clamps for Pushbuttons

For use with 13/16" strut
Item No.
Description
Weight/Piece (lb)
00369666
MQB-21
0.465
Box Qty
10
MQB-41 Clamp
6-5/16"
Features:
4-3/16"

For use with 1-5/8" strut
Item No.
Description
Weight/Piece (lb)
00369668
MQB-41
0.536
Box Qty
10
MQB-82 Clamp
6-5/16"
Features:
For use with 1-5/8" back to back strut
Item No.
Description
Weight/Piece (lb)
00369671
MQB-82
0.75
Box Qty
10
MQB-G41 Clamp
4-3/16"
9-1/16"
Features:
6-5/16"

Wall attachment for 1-5/8" strut
Item No.
Description
Weight/Piece (lb)
00369674
MQB-G41
0.807
Box Qty
10
www.us.hilti.com
8.18
Strut Bases
Technical Data
Material
Strut Bases
Carbon steel
Finish
Features
Electro-galvanized
Reliable and easy to use

Connection of strut to base material
3/ "
4
3/ "
4
3/ "
8
1-3/8"
Item
MQV-2/2D-14
MQP-21-72
MQP-82
MQP-G
Frec (lb)1, 2
1750
1890
2025
2835
2025
Bolt
Double
Quadruple
Double
Quadruple
Double
Pushbutton Tightening Torque

(A)
MD (ft-lb)
MQN
30
MQN
30
MQN
30
MQN
30
MQN
30
1 Based on a safety factor of 2.2

2 Separate design verification of the fastening on the base material must be provided
Wall and Ceiling Strut Base
6-1/2"
4-7/16"
Features:
Two-dimensional double connector for Pushbuttons

Wall, ceiling or floor mount. Used with KWIK-Bolt or HDI anchors
Item No.
Description
Weight/Piece (lb)
00369639
MQV-2/2D-14
0.966
4-7/16"
Frec
Box Qty
10
Light Duty Strut Base
NEW!
Features:
One hole connector for Pushbuttons
Attaches strut to base material
9/ " x 3/ "
16
4
Item No.
Description
Weight/Piece (lb)
00369646
MQP-1/1
0.243
2-3/8"
Box Qty
20
2-3/8"
Standard Strut Base

A
Features:
4-1/8"
6-hole base for Pushbuttons

Attachment to wall, ceiling or floor with KWIK-Bolt II or HDI anchors
Baseplate thickness 1/4" (6 mm)
Item No.
Description
Weight/Piece (lb)
00369651
MQP-21-72
2.535
13/
9
16" x /16"
Frec
1/ "
4
3-1/8"
5-5/16"
7-5/16"
Box Qty
12
1-5/8" Back to Back Strut Base

A
Features:
12-hole base for Pushbuttons
Baseplate thickness 5/16" (8 mm)
Item No.
Description
Weight/Piece (lb)
00369652
MQP-82
4.145
4-3/16"
13/ " x 9/ "
16
16
5/ "
16
3-15/16"
Frec
5-7/8"
7-7/8"
Box Qty
www.us.hilti.com
8.19
Strut Bases
Pivot Base
Features:
6"

Adjustable Angle
Item No.
Description
Weight/Piece (lb)
00369654
MQP-G
2.326
1-15/16"
Box Qty
10
2-15/16"
2-15/16"
2-1/8"
7-1/2"
45 Base
Features:
4-hole 45 angle mount for Pushbuttons
4-1/8"
45
9/
Item No.
Description
Weight/Piece (lb)
00369649
MQP-45
0.772
16"
Box Qty
10
1-5/8"
1-5/8"
www.us.hilti.com
8.20
Accessories
Accessories
Base Plates
Technical Data
Material
Features:
For wall, ceiling or floor attachment of angles, connectors or brackets
with KWIK-Bolt II or HDI anchors
For strut nut or spring nut applications with angles, connectors and brackets
Used as heavy plate washer for strut
Carbon steel
Finish
Electro-galvanized
Item No.
Description
For Thread
Weight/Piece
(lb/g)
Box Qty
00370632
00370633
00370634
MQZ-L 3/8"
MQZ-L 1/2"
MQZ-L 5/8"
3/8"
1/2"
5/8"
0.203 / 92
0.185 / 84
0.176 / 80
20
20
20
7/ "
16
9/ "
16
11/ "
16
1-13/16"
3/
16"
Strut Tie
Features:
NEW!
For user-assembled back to back struts

Item No.
00369691
00369693
Description
Technical Data
Material
Carbon steel
Finish
Item
MQZ-SS*
MQZ-SVS
2-1/16"
Locking device
Magnetic wrench
Width Across
Flats (mm)
Weight/Piece
(lb/g)
13 mm
13 mm
0.006/2.5
Electro-galvanized
Box Qty)
40
1
AF 13
with magnetic insert
* MQZ-SVS tool or 13 mm wrench required to set.
Item
MQZ-SS
Rec. tensile load,1

Zrec (lb/kN)
675/3.0
Rec. shear load,1

Qrec (lb/kN)
1125/5.0
7-7/8"
Tightening torque,
MD (ft-lb/Nm)
15/20
1 Rec. loads based on a safety factor of 2.2
Strut End Cap

Features:
13/16" and 1-5/8" strut sizes
Helps protect sharp edges when handling strut
Item No.
Description
00244886
00313377
MEK Red
MEK Gray
Box Qty
50
50
www.us.hilti.com
8.21
Accessories
Beam Clamp Assembly
Features:
Beam clamp for fastening strut to steel beams
Item No.
Description
00306570
BC-A Beam Clamp Assembly
Box Qty
25
Max. Allowable
Tensile Load = 1100 lb/pair
(Based on a safety factor of 3)
BC-A installed on I-beam
Strut Beam Clamp

Features:
Beam clamp for fastening 1-5/8" strut to steel beam
3/8"
Item No.
00258316
00314330
Description
SBC 1-5/8" Strut Beam Clamp

SBC 2-7/16" to 3-1/4" Strut Beam Clamp
2 3/16"
3/16"
Box Qty
25
25
3 1/4"
3 5/8"
2"
Max. Allowable
Tensile Load = 1100 lb/pair
(Based on a safety factor of 3)
Spring Nut
Features:
Spring nut for 1-5/8" strut
Zinc-plated
Item No.
Description
00258246
00258247
00258248
SNA 1/4" Spring Nut

SNA 3/8" Spring Nut
SNA 1/2" Spring Nut
Box Qty
100
100
100
Channel Nut (without spring)

Features:
Zinc-plated
Item No.
Description
00311937
00311938
00311939
00311940
3/8" Channel Nut

1/2" Channel Nut
5/8" Channel Nut
3/4" Channel Nut
Box Qty
100
100
100
100
www.us.hilti.com
8.22
Strut Clamps
Strut Clamps
Strut Clamp - Copper-Plated (STCC)
Copper plated strut clamps for copper tubing
NOTE: This hanger is not designed for corrosion or electrolysis resistance.
Copper plating is for identification purposes only.
Item No.
Description
00371544
00371545
00371546
00371547
00371548
00371549
00371550
00371551
00371552
00371553
00371554
Strut Clamp Copper 1/4"

Strut Clamp Copper 1"
Strut Clamp Copper 1-1/4"
Box Qty
100
100
100
100
100
100
100
50
50
25
25
Other sizes available by special order
Strut Clamp - Rigid (STCR)

Strut clamp for rigid pipes on strut
Item No.
Description
00371557
00371558
00371559
00371560
00371561
00371562
00371563
00371564
00371565
00371566
Strut Clamp Rigid 1/2"

Strut Clamp Rigid 3/4"
Strut Clamp Rigid 1"
Strut Clamp Rigid 1-1/4"
Box Qty
100
100
100
50
50
50
25
25
25
25
Strut Clamp - EMT (STC-EMT)

Strut clamps for EMT pipe
Item No.
Description
00371568
00371569
00371570
00371571
00371572
00371573
Strut Clamp -EMT 1/2"

Strut Clamp -EMT 3/4"
Strut Clamp -EMT 1"
Strut Clamp -EMT 1-1/4"
Strut Clamp -EMT 1-1/2"
Strut Clamp -EMT 2"
Outside Diameter OD (in.)
Box Qty
0.706"
0.922"
1.163"
1.510"
1.740"
2.197"
100
100
100
50
50
50
Outside Diameter OD (in.)
Box Qty
0.773"
0.986"
1.239"
1.585"
1.820"
2.286"
100
100
50
50
50
50
Strut clamp - Universal (STC-UNIV)

Strut clamp for EMT or rigid pipes
Item No.
Description
00371574
00371575
00371576
00371577
00371578
00371579
Strut Clamp-UNIV 1/2"

Strut Clamp-UNIV 3/4"
Strut Clamp-UNIV 1"
Strut Clamp-UNIV 1-1/4"
Strut Clamp-UNIV 1-1/2"
Strut Clamp-UNIV 2"
www.us.hilti.com
8.23
Strut Clamps
Cushion Clamps & Inserts

Cushion clamps: yellow chromate finish for steel pipe
Item No.
Description
96901692
96901693
96901694
96901695
96901696
96901697
96901698
96901699
96901713
96901714
96901715
96901716
Cushion Clamp 1/4" Pipe

Cushion Clamp 1" Pipe
Cushion Clamp 1-1/4" Pipe
Box Qty
25
25
25
25
10
10
10
10
10
10
5
5
OD cushion clamps: yellow chromate finish for copper pipe

Item No.
Description
96901717
96901718
96901719
96901739
96901720
96901738
96901721
96901740
96901722
96901741
96901723
96901742
96901744
96901745
96901725
96901726
96901727
Cushion Clamp 1/4" Tube O.D.

Cushion Clamp 1" Tube O.D.
Cushion Clamp 1-1/8" Tube O.D.
Box Qty
25
25
25
25
25
25
25
25
20
10
10
10
10
20
10
10
10
Concrete insert strut

NOTE: Concrete Insert Strut supplied with closure strips
Item No.
Description
*
*
Strut CIS 138 - 12/PG 20'

Strut CIS 1316 - 12/PG 20'
Bundle Qty
20
20
* Available by special order
Steel concrete spot insert

NOTE: Nut sold separately. See item below.
Item No.
Description
96900644
96900645
Concrete Insert Plain

Concrete Insert EG (Electro-Galvanized)
Box Qty
100
100
Nut for steel concrete spot insert

Item No.
Description
96900649
96900651
96900646
96900648
96900650
96900652
Nut Concrete Insert Plain 3/8"

Nut Concrete Insert Plain 1/2"
Nut Concrete Insert EG 1/4"
Box Qty
100
100
100
100
100
100
www.us.hilti.com
8.24
Seismic Bracing
Seismic Bracing System

Hilti Seismic Hinge
Item No.
Description
00333309
00369714
00333308
00369715
00369716
HILTI SEISMIC HINGE, STRUT HALF w/ BOLT & NUT

HILTI SEISMIC HINGE, BASE / HANGER HALF, 3/8"
Hanger Rod/
Bolt Diameter
Box Qty
3/8"
1/2"
5/8"
3/4"
10
10
10
10
10
Hanger Rod/
Bolt Diameter
Box Qty
3/8"
3/8"
10
25
Vertical Rod Stiffeners
*Assembled hinge +
Item No.
Description
00370468
00311943
HILTI ROD STIFFENER - EXTERNAL

HILTI ROD STIFFENER - INTERNAL
Speed Lock Clevis Restraining Bolt and Nut (not shown)

Item No.
Description
00339186
00339187
00339188
00339189
00339190
SLC 3" BOLT & NUT (3/8" x 5-1/2")

SLC 4" BOLT & NUT (3/8" x 6-1/2")
SLC 5" BOLT & NUT (1/2" x 7-1/2")
SLC 6" BOLT & NUT (5/8" x 9")
SLC 8" BOLT & NUT (5/8" x 12")
Bolt Diameter
Box Qty
3/8"
3/8"
1/2"
5/8"
5/8"
10
10
10
10
10
www.us.hilti.com
8.25
Hangers
Hilti Speed Lock Clevis
Technical Data
Size range
Time Is MoneyIncrease your productivity with the Hilti SLC Speed Lock Clevis
2" to 8" pipe sizes
Material
Electro-galvanized carbon steel
Approvals:
Factory Mutual FM (2" to 8")
Time Is Money
Your time equals your money. Thats
why Hilti developed the Speed Lock
Clevis. The innovative design and
revolutionary Speed Lock system helps
you greatly increase the efficiency and
productivity of your pipe installations.
Listings
Underwriters Laboratories UL, cUL
(2" to 8")
Conforms with
Federal specifications WW-H-171E
(Type 1)
Manufacturers Standardization
Society MSS-SP-58 (Type 1)
Quick And Easy

Unique Speed Lock System
eliminates hanger disassembly
One pieceno lost/dropped
nuts and bolts
Simple one person
installationsaves you lift time
Installation
Install in accordance with MSS-SP-69
Safe And Reliable

FM approved and UL, cUL listed
Stainless-steel spring on locking
devicelong-term reliable
performance
Item No.
Description
Qty
SLC-EG 2"
00334700
00337250
00334701
00337251
00334702
00337252
00334703
00337253
00334704
00337254
00334705
00337255
1
50
1
50
1
20
1
20
1
10
1
10
SLC-EG 3"
SLC-EG 4"
SLC-EG 5"
SLC-EG 6"
SLC-EG 8"
Weight
per
piece (lb)
Pipe
size
0.32
2"
5"
0.69
3"
1.06
MRI
Min. rod
insertion
Max
allow.
load (lb)*
CL
RS
Rod size
3-9/16"
3-5/8"
3/8"
9/16"
1-1/8"
5/16"
610
6-7/8"
5-1/16"
4-13/16"
1/2"
3/4"
1-5/16"
7/16"
1130
4"
8-1/2"
6-1/8"
5-7/8"
5/8"
15/16"
1-5/8"
7/16"
1430
1.33
5"
9-3/4"
7-5/16"
6-9/16"
5/8"
15/16"
1-3/4"
9/16"
1430
2.80
6"
11-1/4"
8-15/16"
7-7/16"
3/4"
1-1/16"
1-13/16"
11/16"
1940
3.75
8"
13-13/16" 11-3/16"
8-15/16"
3/4"
1-3/16"
2-3/16"
11/16"
2000
* Maximum allowable loads based on the lower of:

1. Maximum safe load of the threaded hanger rod at rod temperature of 650F per Manufacturers Standardization Society Standard Practice 58
2. Allowable load for SLC-EG hanger with a safety factor of 3
3. Industry standard for clevis hangers
RS
Open Hanger
MRI
A
S
H
CL
Close Hanger
www.us.hilti.com
8.26
Hangers
Clevis Hangers
Technical Data
Application
Standard duty clevis hanger: electro-galvanized
Use for the support of stationary,

non-insulated pipe lines
Size range
1/2" to 30" pipe sizes
Material
Electro-galvanized carbon steel
Approvals
Factory Mutual (FM) (2" to 8" only)
Listings
Underwriters Laboratories (UL)
(2" to 8" only)
Conforms with
Federal specification WW-H-171
(Type 1); Manufacturers
Standardization Society
MSS-SP-58(Type 1); install in
accordance with ANSI/MSS-SP-69
Ordering
Specify pipe size and item number.
Sold by the piece. Other sizes
available by special order.
Weight per
piece (lb)
Item No.
Description
00333236
00333237
00333239
00333240
00337250
00337251
00337252
00337253
00337254
00337255
00333242
00333243
SDC-EG 3/4"
SDC-EG 1"
SDC-EG 1-1/2"
SDC-EG 2-1/2"
SLC-EG 2"
SLC-EG 3"
SLC-EG 4"
SLC-EG 5"
SLC-EG 6"
SLC-EG 8"
SDC-EG 10"
SDC-EG 12"
Pipe
size
A
(Rod size)
0.16 3/4" 3/8"

0.18 1" 3/8"
0.32 1-1/2" 3/8"
0.58 2-1/2" 1/2"
Material Size
Upper
Material Size
Lower
2-3/8" 1-13/16"
1/2" 1/4" 12ga x 3/4 14ga x 3/4
2-3/4"
2"
5/8" 1/4" 12ga x 3/4 14ga x 3/4
3-15/16" 2-29/32" 1-1/8" 1/4" 12ga x 1
14ga x 1
5-1/4" 3-3/4" 1-1/8" 5/16" 10ga x 1-1/4 14ga x 1-1/4
Please refer to page 8.26
of SLC-EG
for dimensional information
of SLC-EG
8.90
10.9
10"
12"
Max allow Box

load (lb)1 Qty
7/8" 16-1/2" 10-7/8" 3-1/4" 3/4"

7/8" 18-5/8"
12"
3-1/16" 3/4"
3/8 x 2
3/8 x 2
1/4 x 2
1/4 x 2
610
610
610
1130
50
50
25
25
50
50
20
20
10
10
3600 1
3800 1
1 Based on a safety factor of 3
Technical Data
Application
Insulation Shield
Shield for use with the standard-duty

clevis hangers (SDC)
Material
Pre-galvanized carbon steel
Sold by the piece
Ordering
Other sizes available by special order.
Item No.
Description
ID
Gauge
00306575
00306576
00306577
00306578
00306579
00306580
00306581
00306582
00306583
Insulation Shield 2"

Insulation Shield 2-1/2"
2-1/2"
3"
3-5/8"
4-5/8"
5-5/8"
6-3/4"
8-3/4"
10-3/4"
12-3/4"
18
18
18
18
18
16
16
16
14
12"
12"
12"
12"
12"
12"
12"
18"
24"
Weight/Piece (lb)
0.70
0.84
1.01
1.28
1.60
1.90
3.05
5.63
11.10
www.us.hilti.com
8.27
Hangers
Technical Data
Application
Loop Hanger
Pipe support manufactured to use

minimum rod sizes permitted by NFPA
for fire sprinkler piping
Zinc Plated Loop Hangers

Copper Loop Hangers available by special order
Size range
Material
Pre-galvanized carbon steel with
zinc-electroplated insert nut
Approvals
FM (Factory Mutual)
Listings
UL (Underwriters Laboratories, cUL)
Conforms with
Federal Specification WW-H-171
Standardization Society ANSI/MSS-SP58 (Type 10); install in accordance
with ANSI/MSS-SP-69
Ordering
Loop Hanger
Item No.
Description
Wt.(lb)
per 100
Box Qty
Pipe Size
Rod Size A
Max
allow
load (lb)1
00257353
00257354
00337820
00257356
00257357
00257358
00257359
00257360
00257362
00257364
00257365
LH 1/2"
LH 3/4"
LH 1"
LH 1-1/4"
LH 1-1/2"
LH 2"
LH 2-1/2"
LH 3"
LH 4"
LH 6"
LH 8"
8
10
10
10
10
11
30
34
40
140
170
100
100
100
100
100
100
100
50
50
20
15
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
4"
6"
8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
3-1/4"
3-7/16"
3-3/16"
4"
4-1/4"
4-13/16"
6-1/16"
6-3/8"
7-5/16"
9-7/16"
12"
2-11/16"
2-3/4"
2-1/2"
3-1/8"
3-1/8"
3-1/2"
4-1/4"
4-3/8"
4-13/16"
5-3/4"
7-1/4"
1-3/8"
1-3/8"
1-15/16"
1-7/16"
1-1/8"
1-7/16"
1-5/8"
1-1/2"
1-11/16"
2-7/16"
3"
400
400
400
400
400
400
600
600
1000
1250
1250
Insert Nuts For use with Loop Hangers

Item No.
Description
96901598
96901599
96901600
Insert Nuts EG 3/8" (electro-galvanized)

Insert Nuts EG 1/2" (electro-galvanized)
Insert Nut CP 3/8" (copper plated)
Weight (lb)
per 100
2.6
5.7
2.6
Box Qty
100
100
100
www.us.hilti.com
8.28
Hangers
Split Rings
Technical Data
Application
Split Ring: electro-galvanized
For suspending non-insulated

stationary pipe lines. Allows for piping
runs close to ceilings or walls.
Size range
Material
Malleable iron body, carbon steel rivet
and bolt
Conforms with
Federal specification WW-H-171 (Type
25); Manufacturers Standardization
Society MSS-SP-58 (Type 12); install
in accordance with ANSI/MSS-SP-69.
Ordering
Item No.
Description
00306630
00306631
00306632
00306633
00306634
SR-EG 1/2"
SR-EG 3/4"
SR-EG 1"
SR-EG 1-1/2"
SR-EG 2"
Box Qty
Weight/
Piece (lb)
Pipe Size
Rod Size
(RS)
CL
Min Rod
Insertion (MRI)
100
100
100
50
50
0.18
0.22
0.23
0.34
0.37
1/2"
3/4"
1"
1-1/2"
2"
3/8"
3/8"
3/8"
3/8"
3/8"
7/8"
1"
1-1/32"
1-7/16"
1-5/8"
3/8"
3/8"
3/8"
3/8"
3/8"
Max allow
load (lb)1
180
180
180
180
180
Technical Data
Application
Split ring for copper tubing
For suspending non-insulated

stationary copper tubing lines. Allows
for piping runs close to ceilings or
walls.
Size range
Material
Malleable iron body, carbon steel rivet
and bolt with copper electroplate finish
Conforms with: Federal specification
WW-H-171 (Type 25); Manufacturers
Standardization Society MSS-SP-58
(Type 12); install in accordance with
ANSI/MSS-SP-69
Ordering
Note: this pipe support is not designed for
corrosion or electrolysis resistance.Copper
plating is for identification purposes only.
Item No.
Description
00306623
00306624
00306625
00306626
00306627
00306628
COPPER SR 1/2"
COPPER SR 3/4"
COPPER SR 1"
COPPER SR 1-1/4"
COPPER SR 1-1/2"
COPPER SR 2"
Box Qty
Weight/
Piece (lb)
Pipe Size
Rod Size
(RS)
CL
Min Rod
Insertion (MRI)
100
100
100
100
100
50
0.18
0.22
0.23
0.25
0.34
0.37
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
7/8"
1"
1-1/32"
1-1/32"
1-7/16"
1-5/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
Max allow
load (lb)1
180
180
180
180
180
180
www.us.hilti.com
8.29
Riser Clamps
Riser Clamps
Riser clamps: electro-galvanized
Technical Data
Application
For supporting vertical steel pipe
risers, utilizing the structure to support
the legs on each end of the clamp.
Normally rests on the floor through
which riser passes. Use welded lugs
on pipe above clamp for greater loads.
Size range
Alternate material or finish

Stainless steel and copper plated
Conforms with
Federal specification WW-H-171
ANSI/MSS-SP-69
Ordering
Specify pipe size and item number
Sold by the piece. Other sizes
Item No.
Description
00336347
00336348
00336349
00336350
00336351
00336352
00336354
00336356
00333279
RC-EG 1"
RC-EG 1 1/4"
RC-EG 1 1/2"
RC-EG 2"
RC-EG 2 1/2"
RC-EG 3"
RC-EG 4"
RC-EG 6"
RC-EG 8"
Weight/Piece (lb)
1.05
1.10
1.16
1.33
2.20
2.34
3.33
7.45
9.90
Pipe size
Max allow load1
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
4"
6"
8"
8-15/16"
9-7/16"
9-7/8"
10 1/4"
11"
11-3/4"
13"
16"
18-1/4"
255
255
255
300
400
500
750
1400
2200
Box Qty
25
25
25
20
20
1
1
1
1
www.us.hilti.com
8.30
Pipe Straps / Pipe Clamps
Pipe Straps
Pipe straps: electro-galvanized (For attachment to wall)
Weight per
piece (lb)
Item No.
Description
96900018
96900020
96900022
96900024
96900026
96900028
96900030
96900031
96900032
96900033
Two-hole Pipe strap EG 3/8"

Two-hole Pipe strap EG 1"
Two-hole Pipe strap EG 1-1/4"
Strap ID
0.013
0.018
0.022
0.037
0.052
0.058
0.096
0.180
0.213
0.300
Box Qty
11/16"
1-5/8"
13/16"
1-3/4"
1-1/16"
1-7/8"
1-5/16"
2-3/8"
1-21/32" 2-7/8"
1-7/8"
3-1/4"
2-3/8"
4-1/4"
2-7/8"
4-7/8"
3-1/2"
5-5/8"
4-1/2" 6-15/16"
100
100
100
100
100
50
50
50
50
50
Pipe straps: copper plated (For attachment to wall)

Item No.
Description
96900021
Two-hole Pipe strap CP 3/4"
Weight per
piece (lb)
Comes
with Nails
0.015
yes
Box Qty
100
Pipe Clamps
One-hole pipe clamp: electro-galvanized
(For attachment to wall)
Item No.
Description
96900009
96900010
96900011
96900012
96900013
One-hole Pipe Strap 1/2"

One-hole Pipe Strap 3/4"
One-hole Pipe Strap 1"
One-hole Pipe Strap 1-1/4"
One-hole Pipe Strap 1-1/2"
Weight per
piece (lb)
0.040
0.050
0.100
0.120
0.160
1-7/8"
2-1/2"
3"
3-3/8"
3-7/8"
Max Rec
Load1 Box Qty
3/8" 1/4" 100

1/2" 5/16" 100
5/8" 3/8" 100
3/4" 3/8" 100
3/4" 1/2" 100
100
100
100
100
100
Technical Data
Application
Standard pipe clamp: plain black finish
For suspension of cold or hot pipe

lines where no insulation is required
Size range
Material
Carbon steel
Conforms with
4) and Manufacturers Standardization
Society MSS-SP-58 (Type 4). Install in
accordance with ANSI/MSS-SP-69
Ordering
Item No.
Description
96901025
96901027
96901029
96901031
96901035
96901039
96901041
96901043
96901047
96901051
Standard Pipe Clamp 1-1/2"

Standard Pipe Clamp 2"
Standard Pipe Clamp 2-1/2"
Wt per
piece(lb)
Pipe OD
Gap
A
0.590 1-15/16" 7/8"

0.700 2-3/8" 7/8"
1.010 2-7/8" 7/8"
1.850 3-1/2" 7/8"
2.370 4-1/2" 7/8"
5.100 6-5/8" 7/8"
6.400 8-5/8"
1"
13.500 10-3/4" 1"
20.900
14" 1-1/8"
35.300
18" 1-1/4"
Bolt Hole
Size
C
Material
Size
D
Max
Load1
650F
Max
Load1
750F
Box
Qty
1-7/8"
2-1/4"
2-1/2"
3"
3-5/16"
5-1/8"
6-1/4"
7-1/2"
9"
12"
5/16"
1/2"
1/2"
1/2"
5/8"
3/4"
3/4"
7/8"
7/8"
7/8"
11 ga x 1
1/4 x 1
1/4 x 1
1/4 x 1
1/4 x 1-1/4
3/8 x 1-1/2
3/8 x 1-1/2
1/2 x 2
1/2 x 2-1/2
5/8 x 2-1/2
800
1050
1050
1050
1050
1620
1620
2500
2500
3050
720
940
940
940
940
1440
1440
2230
2230
2720
25
25
25
25
25
1
1
1
1
1
www.us.hilti.com
8.31
Beam Clamps
Beam Clamps
Technical Data
Application
Structural attachment (with infinite
adjustment) to top or bottom of metal
beams, purlins, channel or angle iron
to support hanger rod.
Beam clamps (BC)
Size range
1/4" to 3/4" rod sizes
Material
Malleable iron casting with a hardened
cup point set screw and locknut
Alternate finish
Electro-galvanized
Listings
UL (Underwriters Laboratories) (3/8"
thru 3/4" only)
Approvals
FM (Factory Mutual) (3/8" thru 3/4"
only)
Conforms with
Minimum set-screw
torque (ft-lb)
Item No.
Description
00257366
00257367
00257368
00257369
00258002
00306600
00306601
BC 3/8"
5.0 (60 in-lb)
BC 1/2"
5.0 (60 in-lb)
BC 5/8"
10.0 (120 in-lb)
BC 3/4"
10.0 (120 in-lb)
BC-EG 1/4" 3.5 (40 in-lb)
BC-EG 3/8" 5.0 (60 in-lb)
BC-EG 1/2" 5.0 (60 in-lb)
Maximum set-screw
torque (ft-lb)
Box Qty
Rod Size
Max. Pipe Size
7.5 (90 in-lb)

7.5 (90 in-lb)
15.0 (180 in-lb)
15.0 (180 in-lb)
5.0 (60 in-lb)
7.5 (90 in-lb)
7.5 (90 in-lb)
100
50
50
50
100
100
50
3/8"
1/2"
5/8"
3/4"
1/4"
3/8"
1/2"
4"
8"
8"
8"
4"
8"
Max. Allow Load (lb)1

Top
Bottom
500
950
950
950
500
950
250
760
760
760
250
760
CAUTION! Correct torquing is essential for proper clamp performance.

Note: In the absence of a torque wrench:
a. MINIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-third turn applied to the set-screw.
b. MAXIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-half turn applied to the set-screw.
Beam clamps-wide mouth (BC-WM)

19) and Manufacturers
(Type 19). Install in accordance with
ANSI/MSS-SP-69
Ordering
Specify size and item number
Note: Set screw must be tightened onto the
sloped side of the I-Beam, channel or angle
iron flange. Recommended torque values for
the set screw are as shown in the table.
Technical Data
Application
Structural attachment (with infinite
adjustment) to top or bottom of roll
formed, large lipped metal beams,
purlins, channel or angle iron which
require a 1-1/4" maximum jaw
opening.
Size range
3/8" and 1/2" rod sizes
Material
malleable iron casting with a hardened
cup point set screw and locknut
Alternate finish
Electro-galvanized
Approvals
FM (Factory Mutual)
Listings
UL (Underwriters Laboratories)
Conforms with
Item No.
Description
00306602
00306603
BC-WM 3/8"
BC-WM 1/2"
Recommended Torque
Values (ft-lb)
Box Qty
Rod Size
Max. Pipe Size
5.0
10.0
50
50
3/8"
1/2"
4"
8"
Max. Allow Load (lb)1

Top
Bottom
500
950
250
760
Note: In the absence of a torque wrench:

a. MINIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-third turn applied to the set-screw.
b. MAXIMUM: The set-screw should be finger tightened to the I-Beam and then an additional one-half turn applied to the set-screw.

(Type 19). Install in accordance with
ANSI/MSS-SP-69
Note: Set screw must be tightened onto the
sloped side of the I-Beam, channel or angle
iron flange. Recommended torque values for
the set screw are as shown in the table.
www.us.hilti.com
8.32
Beam Clamps
Beam Clamps
Technical Data
Application
Steel C-clamp with lock nut
Structural attachment to metal

beams, purlins, or angle iron for the
support of hanger rod
Range
3/8" to 5/8" rod size
Material
Carbon steel with hardened steel cup
point set screw and lock nut
Approvals
FM (Factory Mutual)
Listings
Conforms with
23) and Manufacturers Standardization
Society MSS-SP-58 (Type 23). Install
in accordance with ANSI/MSS-SP-69
Set screw must be tightened onto the sloped
side of the I-beam, channel or angle iron flange
and torqued to 60 inch pounds for 3/8" rod
size and 125 inch pounds for 1/2" rod size.
Item No.
Description
00306571
00306572
00306573
C-CLAMP W/LOCK NUT 3/8"

Box Qty
Rod Size
Max. Pipe Size
Min. Rod Insertion
100
50
50
3/8"
1/2"
5/8"
4"
8"
8"
13/16"
13/16"
7/8"
2-5/16"
2-5/16"
2-1/4"
Max allowable1
load (lb)
600
1000
1000
Technical Data
Application
Retainer Straps
To be used when a retainer strap is

specified for the BC and BC-WM beam
clamps
Retainer Straps
Material
Ordering
Sold by the piece
Note
Field bend and use jam nut over
hanger to secure
3/8" to 1/2"
Item No.
Description
00311944
3/8" RETAINER STRAP
Length (in)
12"
Box Qty
1 each
www.us.hilti.com
8.33
Accessories
Accessories
Technical Data
Material
Threaded Rod
AISI 1008 or A36

Item No.
Description
00257963
00257964
00257965
00257966
00257967
00257968
00257969
00257970
00309386
00309387
00309388
00309389
00309390
00309391
00309392
00309393
00309394
00309395
1/4"-6' THREADED ROD - ZINC

1/4"-6' THREADED ROD - PLAIN
Rod size
Weight per pkg (lb)
Max allowable1
tensile load (lb)
Weight
lb/ft
240
610
1130
1810
2710
0.12
0.30
0.50
0.84
1.20
1/4"
3/8"
1/2"
5/8"
3/4"
(Tube) pkg quantity
35.70
42.60
38.80
39.80
36.20
35.70
42.60
38.80
59.50
71.30
61.40
66.50
60.00
59.50
71.30
61.40
66.50
60.00
50
25
12
8
5
50
25
12
50
25
12
8
5
50
25
12
8
5
Lengths
6' and 10'
Finishes
Plain and zinc electroplated to
ASTM B633-85, SC 1 Type I
1 Based on MSS-SP 58, threaded rod has a minimum safety factor of 4.0
Technical Data
Application
Eye Coupler 3/8"
A structural attachment used to join

hanger rod to a structure
Material
Approval
FM (Factory Mutual)
Listing
RS
Item No.
Description
00258317
Eye Coupler 3/8"
Rod
Size (RS)
HS1
HS2
Min Rod
Insertion
(MRI)
Max.
Pipe
Size
Max.
allowable
load (lb)*
3/8"
2-1/4"
1/2"
1/4"
1-3/16"
1 1/8"
4"
250
Box Qty
250
*Load applied axially to threaded rod. Based on capacity of eye coupler only, and a safety factor of 3.
Technical Data
Application
Offset Eye Coupler 3/8"

RS
A structural attachment used to join

hanger rod to a structure. Provides
unlimited vertical rod adjustment.
Size range
3/8" rod size
Material
Approval
FM (Factory Mutual)
Listing
Item No.
Description
00258318
Offset Eye Coupler 3/8"
Rod
Size (RS)
HS1
3/8"
3 1/8"
1/2"
HS2
Min Rod
Insertion
(MRI)
Max.
Pipe
Size
1/4"
1 3/16"
1 1/8"
4"
Max.
allowable
load (lb)* Box Qty
250
250
*Load applied axially to threaded rod. Based on capacity of offset eye coupler only, and a safety factor of 3.
www.us.hilti.com
8.34
Accessories
Accessories
Technical Data: Nuts
Material
Nuts and Washers
ASTM A563 Grade A
Item No.
Description
Dimensions
00335549
00335550
00335551
00336402
00336403
HEX NUT-HEAVY HEX 1/4" (10 x 100)

HEX NUT-5/8"
HEX NUT-3/4"
Item No.
Description
Inside Dia.
Outside Dia.
Pkg Desc
Box Qty
00335552
00335553
00335554
00336404
00336405
WASHER-USS 1/4" (10 x 100)

WASHER-USS 3/8" (10 x 100)
WASHER-USS 1/2" (10 x 100)
WASHER-5/8"
WASHER-3/4"
0.312
0.438
0.562
0.656
0.812
0.734
1.000
1.375
1.312
1.469
Box
Box
Box
Box
Box
1000
1000
1000
250
250
00313068
00313069
00313070
FENDER WASHER 1/4" (10 x 100)

0.281
0.406
0.406
1.250
1.500
2.000
Box
Box
Box
1000
1000
1000
Technical Data
Material
Hex Head Bolts

Pkg Desc
Box Qty
ANSI/ASME B18.2.2 1986
Finish
Technical Data: Washers

Material
AISI 1005 through 1035
Dimensions
ANSI/ASME B18.22.1 1986
Finish
ASTM A307
Dimensions
ANSI/ASME B18.2.1 1981
Finish
Zinc-electroplated to
ASTM B633-85, SC 1, Type I
Technical Data
Material
Grade 2 carbon steel
Finish
Zinc-electroplated to
ASTM B633-85, SC 1, Type I
Item No.
Description
00311951
00311952
00311953
00311954
00311955
HEX HEAD BOLT 3/8" x 1-1/4"

HEX HEAD BOLT 1/2" x 1"
Pkg Desc
Box Qty
Box
Box
Box
Box
Box
1000
1000
1000
250
250
Box
Box
Box
Box
Box
500
500
250
250
250
Rod Couplers
Item No.
Description
00257983
00257984
00257985
00257986
00257987
1/4" ROD COUPLER

3/8" ROD COUPLER
1/2" ROD COUPLER
5/8" ROD COUPLER
3/4" ROD COUPLER
Length
Pkg Desc
Box Qty
7/8"
1-1/8"
1-1/4"
2-1/8"
2-1/4"
Box
Box
Box
Box
Box
1000
500
500
300
200
www.us.hilti.com
8.35
Accessories
Standard U-Bolt
Technical Data
Application
For support, anchor or guidance of
heavy loads.
Size range
Material
Carbon steel
Conforms with
ANSI/MSS-SP-69
Ordering
Standard U-bolt: electro-galvanized

NOTE: Each furnished with 4 hex nuts
Wt per
piece (lb)
Std U Bolt 1/2" pipe EG

Std U Bolt 3/4" pipe EG
Std U Bolt 1" pipe EG
Std U Bolt 1-1/4" pipe EG
0.23
0.24
0.27
0.28
0.30
0.33
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
2-3/8"
2-1/2"
2-3/4"
2-7/8"
3"
3-5/16"
1-5/16"
2"
1-1/2
2"
1-3/4"
2"
2-1/8" 2-1/2"
2-3/8" 2-1/2"
2-13/16" 2-1/2"
15/16"
1-1/8"
1-3/8"
1-3/4"
2"
2-7/16"
100
100
100
100
100
50
96900441
96900443
96900445
96900447

0.70
0.75
0.82
0.88
1/2"
1/2"
1/2"
1/2"
3-13/16"
4"
4-1/4"
4-1/2"
3-7/16"
4-1/16"
4-1/2"
5-1/16"
3"
3"
3"
3"
2-15/16"
3-9/16"
4-1/16"
4-9/16"
50
50
50
50
96900451
96900453
96900455
96900457

2.41
2.84
4.89
7.76
5/8"
5/8"
3/4"
7/8"
6-1/16"
6-15/16"
8-3/8"
9-5/8"
7-3/8"
9-3/8"
11-5/8"
13-3/4"
3-1/2"
3-1/2"
4"
4-1/2"
6-3/4"
8-3/4"
10-7/8"
12-7/8"
1
1
1
1
Item No.
Description
96900429
96900431
96900433
96900435
96900437
96900439
Box Qty
Standard U-bolt: plain

NOTE: Each furnished with 4 nuts
Item No.
Description
96900430
96900432
96900434
96900440
96900442
96900444
96900448
Std U Bolt 1/2" pipe Plain

Std U Bolt 3/4" pipe Plain
Std U Bolt 1" pipe Plain
Std U Bolt 2-1/2" pipe Plain
Wt per
piece (lb)
0.23
0.24
0.27
0.33
0.70
0.75
0.88
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
2-3/8"
1-5/16"
2"
2-1/2"
1-1/2
2"
2-3/4"
1-3/4"
2"
3-5/16" 2-13/16" 2-1/2"
3-13/16" 3-7/16"
3"
4"
4-1/16"
3"
4-1/2"
5-1/16"
3"
15/16"
1-1/8"
1-3/8"
2-7/16"
2-15/16"
3-9/16"
4-9/16"
Box Qty
100
100
100
50
50
50
50
www.us.hilti.com
8.36
Accessories
Side Beam Brackets & Wall Plates
Side Beam Bracket: Electro-galvanized

Item No.
Description
Wt per
piece (lb)
Material
Size
96900594
96900596
96900598
96900600
96900602
Side Beam EG 3/8"

Side Beam EG 1/2"
Side Beam EG 5/8"
Side Beam EG 3/4"
Side Beam EG 7/8"
0.430
0.430
0.800
1.200
1.760
7/16"
9/16"
11/16"
13/16"
15/16"
2
2
3
3-1/2
3-1/2
1-1/2
1-1/2
3
3-7/16
3-1/2
1/2
13/16
1
1-1/4
1-1/4
1/4 x 1-5/8"
1/4 x 1-5/8"
3/8 x 2
3/8 x 2
1/2 x 2
Box Qty
100
100
25
25
10
Side Beam Bracket: Plain Finish

Item No.
Description
96900607
Side Beam Bracket Plain 3/8"
Wt per piece (lb)
Box Qty
0.350
100
Tapped Side Beam Connector

Item No.
Description
Wt per
piece (lb)
Bolt size
Max
pipe size
96900613
Tapped Side Beam 3/8"
0.170
3/8"
2"
Box Qty
100
1/2" Available through special order.
Malleable Iron Wall Plate

Item No.
Description
96900703
96900706
96900704
96900707
Mall Wall Plate Plain 3/8"

Mall Wall Plate Plain 1/2"
Mall Wall Plate EG 3/8"
Mall Wall Plate EG 1/2"
Wt per piece (lb)
Box Qty
0.160
0.160
0.160
0.160
2-3/4"
2-3/4"
2-3/4"
2-3/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
2
2
2
2
100
100
100
100
Technical Data
Application
Brace Fitting: Plain Finish (For 1" Pipe)
For bracing pipe against sway and

seismic disturbances
Item No.
Description
Brace Fitting
Material
Carbon steel
Wt per piece (lb)
Box Qty
0.520
25
Suggested use with Side Beam Attachment sold above

* Available by special order.
Ordering
Specify pipe size and item number
Locking Attachment End

Each assembly includes:
one attachment end to fasten to ceiling and one to fasten to pipe clamp
Max. Bolt
www.us.hilti.com
37
Item No.
Description
*
*
*
*
*
*
Locking Attachment End 3/8 X 1

Locking Attachment End 3/8 X 1-1/4
Pipe Size (in.)
Torque (ft-lb)
1
1-1/4
1
1-1/4
1
1-1/4
20
20
50
50
90
90
Box Qty
30
30
25
25
25
25
* Available by special order.
Accessories
Assorted Screws
Coach screw rod: electro-galvanized

Item No.
Description
Weight/
Piece (lb)
B
Rod Length
Max
Pipe Size
96900121
96900122
96900124
Coach Screw 3/8 X 4

Coach Screw 3/8 X 6
Coach Screw 3/8 X 10
0.100
0.150
0.240
3/8"
3/8"
3/8"
4
6
10
1-1/2"
2"
2"
1-1/2"
2"
2-1/2"
2"
2"
2"
Box Qty
100
100
100
Lag screw: electro-galvanized

Item No.
Description
96900131
96900133
96900134
96900135
96900136
96900138
96900140
96900141
96900142
Lag Screw 1/4" X 1-1/2"

Lag Screw 3/8" X 1"
Lag Screw 3/8" X 1-1/2"
Lag Screw 3/8" X 2"
Lag Screw 3/8" X 2-1/2"
Lag Screw 3/8" X 4"
Lag Screw 1/2" X 2"
Lag Screw 1/2" X 2-1/2"
Lag Screw 1/2" X 3"
Weight/Piece (lb)
0.010
0.040
0.050
0.070
0.080
0.120
0.130
0.160
0.180
Box Qty
100
100
100
100
100
100
50
50
50
www.us.hilti.com
38
Technical Data & Strut Profiles
12 Gauge
HS-1316-12
HS-158-12
HS-2716-12
HS-1316D-12 or MS-21D
HS-158D-12 or MS-41D
Profile Weight
1.307 lb/ft
1.94 kg/m
1.887 lb/ft
2.81 kg/m
2.468 lb/ft
3.67 kg/m
2.533 lb/ft
3.77 kg/m
3.588 lb/ft
5.34 kg/m
Area of Section
0.384 in2
2.48 cm2
0.555 in2
3.58 cm2
0.725 in2
4.68 cm2
0.729 in2
4.70 cm2
1.060 in2
6.84 cm2
Moment of Inertia lx
0.033 in4
1.39 cm4
0.191 in4
7.97 cm4
0.533 in4
22.17 cm4
0.137 in4
5.70 cm4
0.892 in4
37.13 cm4
Moment of Inertia ly
0.138 in4
5.76 cm4
0.237 in4
9.87 cm4
0.336 in4
13.98 cm4
0.264 in4
10.99 cm4
0.454 in4
18.90 cm4
Section Modulus Sx
0.077 in3
1.26 cm3
0.220 in3
3.61 cm3
0.409 in3
6.70 cm3
0.170 in3
2.79 cm3
0.549 in3
9.00 cm3
Section Modulus Sy
0.170 in3
2.79 cm3
0.292 in3
4.78 cm3
0.413 in3
6.77 cm3
0.324 in3
5.31 cm3
0.559 in3
9.16 cm3
Radius of Gyration Rx
0.295 in.
0.75 cm
0.587 in.
1.49 cm
0.857 in.
2.18 cm
0.437 in.
1.11 cm
0.917 in.
2.33 cm
Radius of Gyration Ry
0.601 in.
1.53 cm
0.654 in.
1.66 cm
0.681 in.
1.73 cm
0.602 in.
1.53 cm
0.654 in.
1.66 cm
Gravity Axis e1
0.435 in.
1.10 mm
0.868 in.
2.21 mm
1.302 in.
3.31 cm
0.811 in.
2.06 cm
1.626 in.
4.13 cm
Gravity Axis e2
0.378 in.
0.96 mm
0.757 in.
1.92 mm
1.136 in.
2.88 cm
0.811 in.
2.06 cm
1.626 in.
4.13 cm
Nominal thickness of 12 gauge strip steel is 0.105 inches (2.66 mm)
Slot Configurations
Technical Data & Strut Profiles
Industry Half Slot
Hilti Full Slot
www.us.hilti.com
8.39
Industry Full Slot
14 Gauge
HS-1316-14
HS-158-14
Profile Weight
0.989 lb/ft
1.47 kg/m
1.404 lb/ft
2.09kg/m
Area of Section
0.291 in2
1.87 cm2
0.413 in2
2.66 cm2
Moment of Inertia lx
0.027 in4
1.14 cm4
0.149 in4
6.22 cm4
Moment of Inertia ly
0.108 in4
4.51 cm4
0.182 in4
7.56 cm4
Section Modulus Sx
0.064 in3
1.05 cm3
0.176 in3
2.88 cm3
Section Modulus Sy
0.133 in3
2.18 cm3
0.223 in3
3.66cm3
Radius of Gyration Rx
0.307 in.
0.78 cm
0.602 in.
1.53 cm
Radius of Gyration Ry
0.611 in.
1.55 cm
0.663 in.
1.69 cm
Gravity Axis e1
0.426 in.
1.08 cm
0.849 in.
2.16 cm
Gravity Axis e2
0.387 in.
0.98 cm
0.776 in.
1.97 cm
Nominal thickness of 14 gauge strip steel is 0.075 inches (1.9 mm)
Beam Loading Data
Strut
Beam Span
in.
mm
Max Allow
Uniform Load
lb
kN
Deflection
at Uniform Load
in.
mm
1/180 Span
lb
kN
Uniform Loading at Deflections

1/240 Span
1/360 Span
lb
kN
lb
kN
639
2.834
0.12
2.9
639
2.834
546
2.507
364
1.671
1,837
8.153
0.06
1.4
1,837
8.153
1,837
8.153
1,837
8.153
3,409
15.130
0.04
1.0
3,409
15.130
3,409
15.130
3,409
15.130
1,417
6.298
0.06
1.6
1,417
6.298
1,417
6.298
1,417
6.298
MS-41D
HS-158D-12
4,575
20.292
0.03
0.8
4,575
20.292
4,575
20.292
4,575
20.292
HS-1316-14
535
2.373
0.12
2.9
535
2.373
448
2.056
299
1.371
1,466
6.505
0.06
1.5
1,466
6.505
1,466
6.505
1,466
6.505
426
1.889
0.26
6.5
323
1.486
243
1.114
162
0.743
1,225
5.436
0.13
3.2
1,225
5.436
1,225
5.436
929
4.269
2,272
10.087
0.09
2.2
2,272
10.087
2,272
10.087
2,272
10.087
944
4.198
0.14
3.5
944
4.198
944
4.198
665
3.054
MS-41D
HS-158D-12
3,050
13.528
0.07
1.7
3,050
13.528
3,050
13.528
3,050
13.528
HS-1316-14
356
1.582
0.27
6.6
265
1.219
199
0.914
133
0.609
HS-158-14
977
4.337
0.13
3.3
977
4.337
977
4.337
725
3.332
HS-1316-12
319
1.417
0.47
11.5
182
0.836
136
0.627
91
0.418
918
4.077
0.23
5.8
918
4.077
784
3.602
523
2.401
1,704
7.565
0.16
3.8
1,704
7.565
1,704
7.565
1,455
6.681
708
3.149
0.25
6.2
708
3.149
561
2.577
374
1.718
MS-41D
HS-158D-12
2,288
10.146
0.13
3.1
2,288
10.146
2,288
10.146
2,288
10.146
HS-1316-14
267
1.187
0.48
11.7
149
0.685
112
0.514
75
0.343
HS-158-14
733
3.253
0.24
5.9
733
3.253
612
2.811
408
1.874
HS-1316-12
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
24
610
HS-158-14
HS-1316-12
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
36
914
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
48
1,219
Based on simple beam condition using an allowable design stress of 25,000 psi (172 MPa) with adequate lateral bracing.
See page 8.45 for different load and support conditions.
Above loads include the weight of the member. This weight must be subtracted to determine the net allowable load the beam will support.
Beam loading data is given for solid strut. For beam loading capacity of slotted strut, use 85% of appropriate load from chart. No load reduction is needed for back to back strut.
www.us.hilti.com
8.40
Beam Loading Data
Strut
Beam Span
in.
mm
Max Allow
Uniform Load
lb
kN
Deflection
at Uniform Load
in.
mm
1/180 Span
lb
kN

1/240 Span
1/360 Span
lb
kN
lb
kN
255
1.134
0.73
17.9
116
0.535
87
0.401
58
0.267
735
3.261
0.37
9.0
669
3.073
502
2.305
335
1.537
1,363
6.052
0.24
6.0
1,363
6.052
1,363
6.052
931
4.276
567
2.519
0.39
9.7
479
2.199
359
1.649
239
1.099
MS-41D
HS-158D-12
1,830
8.117
0.20
4.8
1,830
8.117
1,830
8.117
1,559
7.162
HS-1316-14
214
0.949
0.75
18.3
96
0.439
72
0.329
48
0.219
HS-158-14
586
2.602
0.37
9.2
522
2.399
392
1.799
261
1.199
HS-1316-12
213
0.945
1.05
25.8
81
0.371
61
0.279
40
0.186
HS-158-12
612
2.718
0.53
12.9
465
2.134
349
1.601
232
1.067
1,136
5.043
0.35
8.6
1,136
5.043
970
4.454
646
2.969
472
2.099
0.57
14.0
333
249
1.145
166
0.764
MS-41D
HS-158D-12
1,525
6.764
0.28
6.9
1,525
6.764
1,525
6.764
1,083
4.974
HS-1316-14
178
0.791
1.07
26.4
66
0.305
50
0.228
33
0.152
HS-158-14
489
2.168
0.54
13.2
363
1.666
272
1.249
181
0.833
HS-1316-12
182
0.810
1.43
35.2
59
0.273
45
0.205
30
0.136
HS-158-12
525
2.330
0.72
17.6
341
1.568
256
1.176
171
0.784
HS-2716-12
974
4.323
0.48
11.7
950
4.226
712
3.272
475
2.181
405
1.799
0.77
19.0
244
1.122
183
0.841
122
0.561
MS-41D
HS-158D-12
1,307
5.798
0.38
9.4
1,307
5.798
1,193
5.481
796
3.654
HS-1316-14
153
0.678
1.46
35.9
49
0.224
37
0.168
24
0.112
HS-158-14
419
1.859
0.73
18.0
266
1.224
200
0.918
133
0.612
HS-1316-12
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
60
1,524
HS-2716-12
MS-21D
HS-1316D-12
MS-21D
HS-1316D-12
72
84
1,829
2,134
15.27
www.us.hilti.com
8.41
Beam Loading Data
Strut
Beam Span
in.
mm
Max Allow
Uniform Load
lb
kN
Deflection
at Uniform Load
in.
mm
1/180 Span
lb
kN

1/240 Span
1/360 Span
lb
kN
lb
kN
160
0.709
1.87
45.9
45
0.209
34
0.157
23
0.104
459
2.038
0.94
23.0
261
1.201
196
0.900
131
0.600
852
3.782
0.62
15.3
727
3.340
545
2.505
364
1.670
354
1.574
1.01
24.8
187
0.859
140
0.644
94
0.429
MS-41D
HS-158D-12
1,144
5.073
0.5
12.3
1,144
5.073
914
4.196
609
2.798
HS-1316-14
134
0.593
1.91
46.9
37
0.171
28
0.129
19
0.086
HS-158-14
366
1.626
0.96
23.5
204
0.937
153
0.703
102
0.469
HS-1316-12
142
0.630
2.37
58.1
36
0.165
27
0.124
18
0.083
HS-158-12
408
1.812
1.19
29.1
207
0.949
155
0.711
103
0.474
HS-2716-12
757
3.362
0.79
19.4
575
2.639
431
1.979
287
1.320
315
1.399
1.28
31.4
148
0.679
111
0.509
74
0.339
MS-41D
HS-158D-12
1,017
4.509
0.63
15.5
963
4.421
722
3.316
481
2.210
HS-1316-14
119
0.527
2.42
59.4
29
0.135
22
0.102
15
0.068
HS-158-14
326
1.446
1.21
29.8
161
0.740
121
0.555
81
0.370
HS-1316-12
128
0.567
2.92
71.8
29
0.134
22
0.100
15
0.067
HS-158-12
367
1.631
1.46
35.9
167
0.768
125
0.576
84
0.384
HS-2716-12
682
3.026
0.98
24.0
465
2.138
349
1.603
233
1.069
283
1.260
1.58
38.8
120
0.550
90
0.412
60
0.275
MS-41D
HS-158D-12
915
4.058
0.78
19.2
780
3.581
585
2.686
390
1.790
HS-1316-14
107
0.475
2.99
73.3
24
0.110
18
0.082
12
0.055
HS-158-14
293
1.301
1.50
36.7
131
0.600
98
0.450
65
0.300
HS-1316-12
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
MS-21D
HS-1316D-12
MS-21D
HS-1316D-12
96
108
120
2,438
2,743
3,048
www.us.hilti.com
8.42
Beam Loading Data
Strut
Beam Span
in.
mm
Max Allow
Uniform Load
lb
kN
Deflection
at Uniform Load
in.
mm
1/180 Span
lb
kN

1/240 Span
1/360 Span
lb
kN
lb
kN
106
0.472
4.21
103.4
20
0.093
15
0.070
10
0.046
306
1.359
2.11
51.8
116
0.534
87
0.400
58
0.267
568
2.522
1.41
34.5
323
1.485
242
1.113
162
0.742
236
1.050
2.27
55.9
83
0.382
62
0.286
42
0.191
MS-41D
HS-158D-12
763
3.382
1.13
27.6
541
2.487
406
1.865
271
1.243
HS-1316-14
89
0.396
4.30
105.5
17
0.076
12
0.057
0.038
HS-158-14
244
1.084
2.16
52.9
91
0.416
68
0.312
45
0.208
HS-1316-12
91
0.405
5.73
140.7
15
0.068
11
0.051
0.034
HS-158-12
262
1.165
2.87
70.4
85
0.392
64
0.294
43
0.200
HS-2716-12
487
2.161
1.91
47.0
237
1.091
178
0.818
119
0.545
202
0.900
3.09
76.0
61
0.280
46
0.210
31
0.140
MS-41D
HS-158D-12
654
2.899
1.53
37.6
398
1.827
298
1.370
199
0.914
HS-1316-14
76
0.339
5.85
143.6
12
0.056
0.042
0.028
HS-158-14
209
0.929
2.93
72.0
67
0.306
50
0.229
33
0.153
HS-1316-12
64
0.283
11.70
287.1
0.033
0.025
0.017
HS-158-12
184
0.815
5.86
143.8
42
0.192
31
0.144
21
0.100
HS-2716-12
341
1.513
3.91
95.9
116
0.534
87
0.401
58
0.267
142
0.630
6.31
155.2
30
0.137
22
0.103
15
0.069
MS-41D
HS-158D-12
458
2.029
3.13
76.8
195
0.895
146
0.671
97
0.448
HS-1316-14
53
0.237
11.94
293.1
0.027
0.021
0.014
HS-158-14
147
0.651
5.99
147.0
33
0.150
24
0.112
16
0.075
HS-1316-12
HS-158-12
HS-2716-12
MS-21D
HS-1316D-12
MS-21D
HS-1316D-12
MS-21D
HS-1316D-12
144
168
240
3,658
4,267
6,096
www.us.hilti.com
8.43
Allowable Loads MQK Bracket
F1
F1 = qxl
F1
1/2 1/2
Bracket
(continued below)
Type of load 1 - uniform

F1 [lb]
Kwik Bolt II 2
1
Steel
1/2" x 3-3/4"
lb
N
lb
N
Type of load 2 - single

F1 [lb]
Kwik Bolt II 2
1
Steel
1/2" x 3-3/4"
lb
N
lb
N
Type of load 3
F1 [lb]
Kwik Bolt II 2
1
Steel
1/2" x 3-3/4"
lb
N
lb
N
L (in.)
L (mm)
MQK-21/300
11-13/16"
300
205
910
205
910
240
1070
240
1070
75
335
75
335
MQK-21/450
17-11/16"
450
90
400
90
400
140
625
140
625
35
155
35
155
MQK-41/3/300
11-13/16"
300
920
4095
735
3270
920
4095
735
3270
460
2045
365
1625
MQK-41/3/600
23-5/8"
600
395
1755
365
1625
460
2045
365
1625
145
645
145
645
MQK-72/600
23-5/8"
600
1025
4560
645
2870
1025
4560
645
2870
510
2270
320
1425
MQK-21 D/300
11-13/16"
300
680
3025
680
3025
680
3025
680
3025
340
1510
340
1510
MQK-21 D/600
23-5/8"
600
280
1245
280
1245
340
1510
340
1510
105
465
105
465
Bracket
(continued from above)
L (in.)
Steel 1
L (mm)
F2 F2
F3 F3 F3
1/3 1/3 1/3
1/4 1/4 1/4 1/4
Type of load 4
F2 [lb]
Kwik Bolt II 2
1/2" x 3-3/4"
lb
N
lb
Steel 1
N
Type of load 5
F3 [lb]
Kwik Bolt II 2
1/2" x 3-3/4"
lb
N
lb
MQK-21/300
11-13/16"
300
120
535
120
535
80
355
80
355
MQK-21/450
17-11/16"
450
60
265
60
265
35
155
35
155
MQK-41/3/300
11-13/16"
300
460
2045
365
1625
305
1355
245
1090
MQK-41/3/600
23-5/8"
600
230
1025
180
800
150
665
120
535
MQK-72/600
23-5/8"
600
510
2270
320
1425
340
1510
215
955
MQK-21 D/300
11-13/16"
300
340
1510
340
1510
225
1000
225
1000
MQK-21 D/600
23-5/8"
600
170
755
170
755
110
490
110
490
1 Loading capacity of bracket (steel load capacity)

2 Loading capacity of bracket fastened with Kwik Bolt II 1/2" x 3-3/4" (with an embedment depth of 3")
The loads apply only if bracket fastenings are correctly positioned, i.e. strut opening pointing upwards.
The brackets own weight has been allowed for.
Concrete strength minimum 2000 psi.
The loads apply only if the bracket is fastened away from a component edge (fastenings made at component edges must be designed separately).
Separate verification must be provided that forces are transferred to the respective base material, i.e. steel and concrete.
The application guidelines in anchor approvals must be observed.
Load values are based on the lesser of allowable stress or a deflection limit of L/180 at the outer most loading point.
Allowable Loads for MQK Brackets with MQK-SK and MQK-SL Supports
F1
Bracket
Length
F1
MQK-SL
F1
MQK-SL
MQK-SL
in.
mm.
lb
lb
lb
MQK-41/3/600
23-5/8"
600
1010
4500
785
3500
450
2000
MQK-72/600
23-5/8"
600
1350
6000
785
3500
560
2500
MQK-21 D/600
23-5/8"
600
785
3500
785
3500
335
1500
8.44
Technical Data - Strut
Load and support condition
Load factor
Deflection factor
Simple Beam - Uniform Load
1.00
1.00
Simple Beam - Concentrated Load at Center
0.50
0.80
Simple Beam - Two Equal Concentrated Loads at 1/4 Points
0.50
1.10
Beam Fixed at Both Ends - Uniform Load1.50
0.30
Beam Fixed at Both Ends - Concentrated Load at Center
1.00
0.4
Cantilever Beam - Uniform Load
0.25
2.40
Cantilever Beam - Concentrated Load at End
0.12
3.20
Continuous Beam - Two Equal Spans, Uniform Load on One Span
1.30
0.92
Continuous Beam - Two Equal Spans, Uniform Load on Both Spans
1.00
0.42
Continuous Beam - Two Equal Spans, Concentrated Load at Center of One Span
0.62
0.71
Continuous Beam - Two Equal Spans, Concentrated Load at Center of Both Spans
0.67
0.48
www.us.hilti.com
8.45
Cast Iron Pipe Data
Nominal
pipe
size
Class
3"
150
4"
150
6"
150
8"
150
10"
150
12"
150
14"
150
16"
150
18"
150
20"
150
24"
150
30"
150
36"
150
42"
150
48"
150
PVC Plastic Pipe Data

OD
(in.)
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
Wall
thickness
(in.)
0.32
0.35
0.38
0.41
0.44
0.48
0.51
0.54
0.58
0.62
0.73
0.85
0.94
1.05
1.14
Wt per
foot
(lb)
12.2
16.4
25.7
36.7
48.7
62.9
78.8
95.0
114.7
135.9
190.4
277.3
368.9
479.1
595.2
Wt of
water
per ft
(lb)
3.73
5.72
12.80
23.10
35.50
51.00
69.30
90.30
114.00
141.50
201.00
312.00
449.00
612.00
803.00
Glass Pipe Data
Regular Schedule
Nominal
pipe
size
1 1/2"
2"
3"
4"
6"
OD
(in.)
1.84
2.34
3.41
4.53
6.66
Wall
thickness
(in.)
0.12
0.14
0.17
0.20
0.24
Wt per
foot
(lb)
0.64
0.94
1.60
2.60
4.70
Wt of
water
per ft
(lb)
0.89
1.45
3.19
5.79
12.78
Wt per
foot
(lb)
0.60
0.87
1.10
2.00
3.40
6.30
Wt of
water
per ft
(lb)
0.35
0.76
1.36
3.06
5.44
12.42
Heavy schedule
Nominal
pipe
size
1"
1 1/2"
2"
3"
4"
6"
OD
(in.)
1.31
1.84
2.34
3.41
4.53
6.66
Wall
thickness
(in.)
0.16
0.17
0.17
0.20
0.26
0.33
Schedule 40 and 80
Nominal
pipe Schedule
size
No.
1/8"
40
80
1/4"
40
80
3/8"
40
80
1/2"
40
80
3/4"
40
80
1"
40
80
1 1/4"
40
80
1 1/2"
40
80
2"
40
80
2 1/2"
40
80
3"
40
80
3 1/2"
40
80
4"
40
80
5"
40
80
6"
40
80
8"
40
80
10"
40
80
12"
40
80
OD
(in.)
0.405
0.540
0.675
0.840
1.050
1.315
1.660
1.990
2.375
2.875
3.500
4.000
4.500
5.563
6.625
8.625
10.750
12.750
Wall
thickness
(in.)
0.068
0.095
0.088
0.119
0.091
0.126
0.109
0.147
0.113
0.154
0.133
0.179
0.140
0.191
0.145
0.200
0.154
0.218
0.203
0.276
0.216
0.300
0.226
0.318
0.237
0.337
0.258
0.375
0.280
0.432
0.322
0.500
0.366
0.593
0.406
0.687
Wt per
foot
(lb)
0.043
0.055
0.074
0.094
0.100
0.129
0.150
0.150
0.199
0.259
0.295
0.382
0.400
0.527
0.478
0.639
0.643
0.884
1.020
1.350
1.333
1.804
1.598
2.195
1.899
2.636
2.770
4.126
3.339
5.028
5.280
8.023
7.505
11.894
10.023
16.365
Wt of
water
per ft
(lb)
0.025
0.016
0.045
0.031
0.083
0.061
0.132
0.101
0.230
0.186
0.374
0.311
0.647
0.555
0.882
0.765
1.452
1.279
2.072
1.834
3.200
2.860
4.280
3.850
5.510
4.980
8.660
7.870
12.150
11.290
21.600
19.800
34.100
31.100
48.500
44.000
1 cubic foot of water weighs 62.35 lb

1 gallon (US) weighs 8.335 lb
www.us.hilti.com
8.46
Copper Tube Data
Steel Pipe Data
Type L
Schedule 40 and 80
Nominal OD
pipe tubing
size
(in.)
1/4"
3/8"
1/2"
5/8"
3/4"
1"
1 1/4"
1 1/2"
2"
2 1/2"
3"
3 1/2"
4"
5"
6"
8"
10"
12"
3/8
1/2
5/8
3/4
7/8
1 1/8
1 3/8
1 5/8
2 1/8
2 5/8
3 1/8
3 5/8
4 1/8
5 1/8
6 1/8
8 1/8
10 1/8
12 1/8
OD
(in.)
Wall
thickness
(in.)
Wt per
foot
(lb)
Wt of
water
per ft
(lb)
0.375
0.500
0.625
0.750
0.875
1.125
1.375
1.625
2.125
2.625
3.125
3.625
4.125
5.125
6.125
8.125
10.125
12. 125
0.030
0.035
0.040
0.042
0.045
0.050
0.055
0.060
0.070
0.080
0.090
0.100
0.110
0.125
0.140
0.200
0.250
0.280
0.126
0.198
0.285
0.362
0.455
0.655
0.884
1.14
1.75
2.48
3.33
4.29
5.38
7.61
10.20
19.29
30.10
40.40
0.034
0.065
0.100
0.151
0.209
0.357
0.546
0.767
10.341
2.064
2.949
3.989
5.188
8.081
11.616
20.289
31.590
45.426
Type K
Nominal OD
pipe tubing
size
(in.)
1/4"
3/8"
1/2"
5/8"
3/4"
1"
1 1/4"
1 1/2"
2"
2 1/2"
3"
3 1/2"
4"
5"
6"
8"
10"
12"
3/8
1/2
5/8
3/4
7/8
1 1/8
1 3/8
1 5/8
2 1/8
2 5/8
3 1/8
3 5/8
4 1/8
5 1/8
6 1/8
8 1/8
10 1/8
12 1/8
OD
(in.)
Wall
thickness
(in.)
Wt per
foot
(lb)
Wt of
water
per ft
(lb)
0.375
0.500
0.625
0.750
0.875
1.125
1.375
1.625
2.125
2.625
3.125
3.625
4.125
5.125
6.125
8.125
10.125
12.125
0.035
0.049
0.049
0.049
0.065
0.065
0.065
0.072
0.083
0.095
0.109
0.120
0.134
0.160
0.192
0.271
0.338
0.405
0.145
0.269
0.344
0.418
0.641
0.839
1.04
1.36
2.06
2.92
4.00
5.12
6.51
9.67
13.87
25.90
40.30
57.80
.032
.055
.094
.144
.188
.337
.527
.743
1.310
2.000
2.960
3.900
5.060
8.000
11.200
19.500
30.423
43.675
Nominal
pipe Schedule
size
No.
3/8"
40
80
1/2"
40
80
3/4"
40
80
1"
40
80
1 1/4"
40
80
1 1/2"
40
80
2"
40
80
2 1/2"
40
80
3"
40
80
3 1/2"
40
80
4"
40
80
5"
40
80
6"
40
80
8"
40
80
10"
40
80
12"
40
80
14"
40
80
16"
40
80
18"
40
80
20"
40
80
24"
40
80
30"
20
36"
API
OD
(in.)
0.675
0.840
1.050
1.315
1.660
1.900
2.375
2.875
3.500
4.000
4.500
5.563
6.625
8.625
10.750
12.750
14.000
16.000
18.000
20.000
24.000
30.000
36.000
Wall
thickness
(in.)
0.091
0.126
0.109
0.147
0.113
0.154
0.133
0.179
0.140
0.191
0.145
0.200
0.154
0.218
0.203
0.276
0.216
0.300
0.226
0.318
0.237
0.337
0.258
0.375
0.280
0.432
0.322
0.500
0.365
0.530
0.406
0.687
0.437
0.750
0.500
0.843
0.563
0.937
0.593
1.031
0.687
1.218
0.500
0.500
Wt per
foot
(lb)
0.567
0.738
0.850
1.087
1.130
1.473
1.678
2.171
2.272
2.996
2.717
3.631
3.652
5.022
5.790
7.660
7.570
10.250
9.110
12.510
10.790
14.980
14.620
20.780
18.970
28.570
28.550
43.390
40.480
64.400
53.600
88.600
63.000
107.000
83.000
137.000
105.000
171.000
123.000
209.000
171.000
297.000
158.000
190.000
Wt of
water
per ft
(lb)
0.083
0.061
0.132
0.101
0.230
0.311
0.374
0.311
0.647
0.555
0.882
0.765
1.452
1.279
2.072
1.834
3.200
2.860
4.280
3.850
5.510
4.980
8.660
7.870
12.510
11.290
21.600
19.800
34.100
31.100
48.500
44.000
58.500
51.200
76.500
69.700
97.200
88.500
120.400
109.400
174.200
158.200
286.000
417.000
1 cubic foot of water weighs 62.35 lb

1 gallon (US) weighs 8.335 lb
www.us.hilti.com
8.47
www.us.hilti.com
8.48
Hilti CP 680 Cast-In Firestop Device
Firestop Systems
Firestop Systems
Hilti Firestop Solutions
Firestop Systems
Page 9.5+
Page 9.7+
Accessories
Dispensers
System Identification
Mineral Wool
Insta-Back Drywall Repair
Technical Resources
Hilti Firestop Guide to Specification, Installation & Inspection
Online Tech Center www.us.hilti.com
Online Design Center www.us.hilti.com/firestopdc
Page 9.24
Page 9.25
Page 9.25
Page 9.25
Product Information
See Page
9.7
Features
Benefits
CP 680
Firestop Cast-in Device
Quick and simple installation

Integrated water and smoke seal
Tested in concrete floor thicknesses
from 2-1/2" (63 mm)
Innovative adapter for metal deck applications
Ready to use no additional caulk required

Easy to specify, install and inspect
Cost effective solutions
9.8
CP 681
Tub Box Kit
Assembles easily with solvent cement no

additional tools required
Triangular shape makes working around rebar
easy
3 fastening points instead of 4 reduces installation time
Saves time and labor costs

Stable during concrete pouring
No special tools required for installation
9.9
Aerator Adapter
For use with CP 680
Allows for vertical/horizontal and angle

movement
Allows for aerator positioning in 360 degree
radius
No limitation for pipe/aerator connection
Simple and flexible installation

Coupler or welding installation
9.10
FS-ONE
High Performance
Intumescent Firestop
UL Listings for various penetrating items

Several 1/4" depth systems
Available in foil pack (600 mL)
ONE product to specify, purchase or inspect

for most applications
Low cost per penetration
Quick and simple installation procedure
Soft flexible design

Easy to cut and shape
User friendly UL designs
Innovative designs
Easy to install, reuse and repenetrate

Just trim BLOCK to fit around penetrating
items
Reduces need for extra labor, tools and parts
Easiest solution for large openings with
multiple penetrations
Firestopping combustible pipe penetrations

Firestopping insulated pipe penetrations
Difficult applications where space is limited
Penetrations through concrete over metal
deck
Quick and easy closure without the use

of a tool
Ideal for very tight installations
tlk
e0
9^
)&
(/R
84
sod
tc
fm,
)v
Z8Z ev
64
iJd
53
4i5 23aw jfiw
kird
hriu
u9+ wilo p3i4e h.
12 i4jt
028 NoW
oeo f-x
-.vb 8u27 E
o
vbv uze
h, irei
v
A water-based intumescent
firestop sealant,
designed to expand when
exposed to heat
FS 657
Fire Block
9.11
An innovative and simple

to install firestop block
designed to expand when
exposed to heat
9.12
CP 645
Firestop Wrap Strip
An intumescent, flexible
firestop wrap for
plastic and insulated pipe
penetrations
9.139.14
A ready-to-use firestop
device designed to collapse
plastic pipe penetrations
when exposed to fire conditions
h.
ma
CP 642/CP 643
Firestop Collar
nsc
E
ze
eiv
CP 672
Speed Spray
Firestop
System
9.15
A flexible fire-rated mastic

for construction joints
where movement up to
50% is expected
www.us.hilti.com
Ready-to-use out of package

Adjustable mounting tabs
Low profile design (CP 643)
Simple and quick installation

Flexibility in positioning of collar
Allows for correct installation in tight areas
(CP 643)
Water based formulation

Maximum flexibility
Can be used with standard texture
spray equipment
Fast and easy clean-up

Tested to new UL 2079 Test Standard
No special modification or extra expense for
product application
For complete firestop technical information, refer to the

Hilti Firestop Systems Guide to Specification, Installation & Inspection.
Contact your Hilti Sales Representative or Customer Service for your copy today.
Joints
Multiple penetrations
Metal ducts
Insulated metal pipes
Cables/cable trays
Product Description
A one step cast-in firestop

device for a wide variety of
pipe materials and diameters
9.3
Plastic/glass pipes
Firestop Systems Application Review
Metal pipes
Application
Product Information
See Page
Product Description
Features
Benefits
CP 777
Speed Plugs
Leaves no gaps or voids

Smooth surface porvides cost
effective spray coverage
No asbestos. Inorganicwill not mildew
Up to 60% faster than castle cutting
Pre-cut flute configuration

for top of wall firestopping
Firestop
System
9.16
9.17
Pre-cut
Superior finish
Safe to use
User friendly
CP 767
Speed Strips
CP 601S
Elastomeric Firestop
Sealant
Joints
Metal ducts
Cables/cable trays
Plastic/glass pipes
Firestop Systems Application Review
Metal pipes
Application
Silicone based formula

1/4" depth systems
Allows for movement and vibration

Cost effective solutions
Fast and easy dispensing
1/4" depth systems

Excellent elongation/compression properties
Resistant to smoke, fumes and water
Meets 500 cycle requirements
(ASTM E 1399 & UL 2079)
Smoke, fumes and water resistant

No tooling required
One stop application

Virtually impervious to smoke
Fully cures in approximately 1 minute
No additional materials required
High yield
One solution for various applications

Easy handling for difficult to reach
applications
Use with confidence
UL Classified, FM Approved
A single component silicone firestop sealant for

joint applications where
movement up to 25% is
expected
CP 604
Self-Leveling Firestop
Sealant
9.18
A self-leveling, single-component, silicone-based firestop

sealant for use with throughpenetrations as well as con-
struction joints in floors
CP 620
Fire Foam
9.19
CP 620
Brandsch
utzbesch
ichtung
sodfm,ev
iJdjfiwhriuh
. NoWE
4i5kirdwiloi
u9+12oeo4jtf-x-.vbv
bvh, ireiv
o
Universal firestopping solution for common construction materials. Use in conjunction with CP 645 wrap
strip
CP 606
Flexible Firestop
Sealant
9.20
* When used with CP 645 Wrap Strip

Acrylic based formula
Can be painted
Fast and easy clean-up with water

Allows for excellent finished appearances
Fast and easy dispensing
Mixes in its own container

Some applications require
minimum 2-1/2" depth
Cleans up with water
No need for added pails

Economical and simple to use
Fast and easy clean-up
6"x 7" or 7" x 7" or 9" x 9" pad sizes

1 & 2 hour listing
Tested for wood and steel studs
Fits most common electrical boxes

Only one pad to stock and install
Can be used for commercial and residential
applications
Non-curing formulation
No volatile solvents
Intumescent
Reusable and easily repenetrated

Approved for combustible penetrations
(cables) along with conduit,
EMT and steel pipe
An acrylic based firestop

sealant for through penetration applications or joint
applications where movement up to 10% is expected
CP 637
Firestop Mortar
9.21
Dry powder, which is mixed

with water to form a
pourable or trowelable
firestop mortar
CP 617/617 L / 617 XL
Firestop Putty Pad
9.22
An intumescent putty sheet

designed to help protect
electrical outlet boxes
9.23
CP 618
Firestop Putty Stick
An intumescent putty which
remains pliable over time

www.us.hilti.com
9.4
Restoration of Fire-Rated Structural Elements

10
Problem Areas
The illustration on the left indicates a range
of typical problems facing the designer.
Construction may consist of:
concrete
wood
gypsum
The problem areas are:
7
11
Movement joints
Rigid or low movement joints
Head of wall and perimeter joints
Metal and plastic pipes
Plastic pipes
Multiple penetrations, pipes and/or cables
Cable trays (with permanent sealing of

opening during construction, or temporary
sealing allowing additional cables to be
installed subsequently)
Cable trays (with permanent sealing of

opening during construction)
Cables (single or bundled)
10
Electrical outlet boxes
11
Heating/ventilation/air conditioning
Fire Resistance Rating
To help prevent the rapid spread of fire within a

building, certain walls, floors and joints are
required to meet a specific fire resistance
ratingthe period of time during which a building
component has been tested to confine a fire or
continue to perform a structural function or both.
Through-penetrations and joints created during
the construction process require the installation of
firestop systems in order to bring the wall or floor
back up to its original fire-rating.
Firestopping
1
5
It is essential that every penetration or joint in a

fire-rated wall or floor is adequately protected by
sealingor firestopping such that the building
component is restored to its original fire-rated
condition in order to maintain compartmentalization.
The quality and excellence of Hilti Firestop Products
help ensure that fire, smoke and toxic gases are
contained to reduce the tragic loss of human life
and damage to property.
www.us.hilti.com
9.5

The illustration on the right provides a basic guide

to the range of Hilti Firestop products available for
the applications shown
3
12
CP 606 Flexible Firestop Sealant

CP 601S Elastomeric Firestop Sealant
1-A
CP 604 Self-Leveling Firestop Sealant
CP 672 Speed Spray
CP 680 Firestop Cast-In Device
CP 642 Firestop Collar

CP 645 Firestop Wrap Strip
FS 657 Fire Block
CP 637 Firestop Mortar
CP 618 Firestop Putty Stick
CP 617 / CP 617L / CP 617XL

Firestop Putty Pad
10
FS-ONE High Performance

Intumescent Sealant
10

11
CP 620 Fire Foam
12
CP 777 Speed Plugs
13
CP 604 Self-Leveling Firestop Sealant
11
10
6
11
8
6
Firestop Design Center online

System design search by through-penetration
or joint application
Direct link to Hilti Tech Center for additional
technical information about Hilti products
Search for UL System drawings by number
Firestop Terms & Definitions
Project References
Firestop FAQs
UL Nomenclature
Engineering Judgments
Fire Protection Triangle
Building, Regulations & Codes
CSI Format Specifications
UL Drawing Schedules
Submittal Toolkit
Firestop Detail Sheets
13
10
4
2
1-A
1
Online Design Center

www.us.hilti.com/firestopdc
www.us.hilti.com
9.6
Firestop Systems
Technical Data
Dimensions CP 680-75/2.5"
O.D. of fastening flange: 6.4" (162 mm)
Metal Deck Opening Size Required
When Used With Adapter: 4.3"
(110 mm)
CP 680
Cast-In Firestop Device
System Advantage /
Customer Benefits
Dimensions CP 680-110/4"
One step simple and fast

installation
No additional caulking required
Ready to use out of the package
Ecomomical in use with short
installation time
Easy to remove and replace pipe
Allows for pipe adjustments
during installation
O.D. of fastening flange: 8.5" (215 mm)

When Used With Adapter: 6.7"
(170 mm)
Dimensions CP 680-160/6"
O.D. of fastening flange: 11.1"
(282 mm)
When Used With Adapter: 9"
(230 mm)
Put Hilti Firestop

Cast-In Solutions
to work.
Expansion temperature
392F (200C)
Expansion rate
1:50 (unrestrained)
1:30 (Load expansion,Load=20g/cm3)
CP 680 in concrete deck
CP 680 over metal deck
Maximum 212F (100C)
Product description
Types of installation
For use with
Color
Innovation that has revolutionized

the firestopping of pipes through
concrete floors and concrete over
metal decking.
A one step cast-in firestop device
for a variety of pipe
materials and diameters.
Concrete floors from 2.5"

(63 mm) thickness
Concrete floors from 2.5"
(63 mm) thickness over
metal decking
Metal pipesinsulated or noninsulated

Plastic pipes such as PVC, CPVC,
ABS, ENT and FRPP
EMT and electrical conduits
Cable bundles
Multiple pipes
Floor assemblies rated up to 3
hours
Height
10"
Temperature resistance
Red
Approvals
ER 5071
California State Fire Marshal

Listing No. 4485-1200:116
City of New York

MEA-102-00-M, Vol. II

UL 1479
ASTM E 814
UL 2043
Product features
Quick and simple installation
Integrated water and smoke seal
Tested in concrete floor
thicknesses from 2.5" (63 mm)
Innovative adapter for metal deck
applications
Approved for plenums
Areas of application
Fresh water pipes
Waste water pipes
Dust and fiber-free environments
such as hospitals,
computer centers and
laboratories
Not suited for use with

Areas with high condensation
Outdoor areas
Wall applications
Internationally tested and

approved
FIRESTOP DEVICE
FOR USE IN THROUGH-PENETRATION
FIRESTOP SYSTEMS
SEE UL FIRE RESISTANCE DIRECTORY
5N76
FM
APPROVED
F
Fi
CP 680 Cast-In Device

Item No.
Description
00333545
00337457
00333547
CP 680-75 / 2.5" Cast-In Device

CP 680-110 / 4" Cast-In Device
CP 680-160 / 6" Cast-In Device
Qty/Pkg
1
1
1
CP 680 Metal Deck Adapter

Each metal-deck adapter kit includes 2 metal plates and 1 rigid plastic extension tube.
Item No.
Description
00333551
00333552
00333553
CP 680- Metal Deck Adapter 75 / 2.5"

CP 680- Metal Deck Adapter 110 / 4"
CP 680- Metal Deck Adapter 160 / 6"
Qty/Pkg
1/bag
1/bag
1/box
wing clip
www.us.hilti.com
Firestop Design Center
9.7
Plastic
extension tube

Firestop Systems
CP 681
Technical Data
Dimensions (LxWxH)
NEW!
Tub Box Kit
10-3/4" x 13" x slab thickness
Application dimension
System Advantage / Customer
Benefits
Enhanced system stability, no

additional fastening materials
needed
Unique triangular shape, easier to
work around rebar
Pre-cut to customer height, no
additional adjustment required
Easy assembly, just glue it
together with PVC cementno
special tools needed
One system for all pipe materials,
easy to choose and inspect
Special elastomeric bushing, no
protecting tape required
Pipe support products available
for one stop buy
Creates a 2-1/2" deep recess in the

slab
Minimum slab thickness

4-1/2"
Intumescent activation
Approx. 375F (190C)
Expansion ratio (unrestricted)

1:10
Maximum 212F (100C)
Color
Red with white PVC legs and coupling
Storage
Store in dry location
Approvals
In progress; call for details

UL 1479
ASTM E 814
Put Hilti Firestop

Cast-In Solutions
to work.
The Hilti Cast-In Solutions
include an innovative tub box
solution.
Improved system stability
stable during concrete pouring
Assembles easily with solvent
cement no additional tools
required
Triangular shape makes working
around rebar easy
3 fastening points instead of 4
reduces installation time
Pre-cut to customers height

requirement saves expensive
field labor costs
One system for all pipe materials,
easy to choose and inspect
The CP 681 Tub Box Kit

includes an Elastomeric
Sealing Bushing.

approved
FIRESTOP DEVICE
FIRESTOP SYSTEMS
5N76
Versatile CP 681 tub box kit

allows sealing bushing to be
installed from top or bottom
Accepts a pass through 1-12"
pipe or a standard 2" P-trap
direct connection to the coupling
Sealing bushings available for

standard schedule 40 pipe or
thin wall piping
CP 681 Tub Box Kit

Item No.
Description
98459145
Tub Box Kit Complete

Precut to desired slab thickness
Qty/Pkg
Includes sealing bushing for schedule 40 pipe
00377920
Tub Box Kit Standard

Uncut 10-1/2" Height
Includes sealing bushing for schedule 40 pipe; cut to desired

height in field
98459148
1-1/2" Thin wall seal

(sealing bushing for thin wall pipe)
NOTE: Drain and overflow piping provided by contractor

www.us.hilti.com
9.8
Firestop Systems
Aerator Adapter Technical Data
Dimensions
9" dia. x 4" height
Application dimension
Creates 7-3/4" x 4"deep recess in the
slab
Minimum slab thickness
Aerator Adapter
NEW!
For use with CP 680
Use in combination with CP 680-110/4"

(Item No. 00337457) for firestopping Aerator Assemblies
System Advantage /
Customer Benefits
6"
Flexibility in choice of pipe

connections, i.e. coupling and
welding, etc. to meet customer
requirements
360 turn radius of aerator
enables it to be set in any position
Direct connection to the vertical
waste pipe reduces pipe
interfaces
Excellent sound insulation to
satisfy the building owner
Fast installation when you utilize
Hilti concrete spot insert anchors
(see page 8.24 for ordering
information) for pipe supports
Provide all pipe support products
for one-stop buy
Maximum 212F (100C)
Color
Red
Storage
Store in dry location
Approvals
In progress; call for details

UL 1479
ASTM E 814
Put Hilti
Firestop
Cast-In
Solutions
to work.
Product description
Product features
For use with
Used in conjunction with CP 680 to

provides an underside concrete deck
recessed area for the installation of
single stack waste pipe system
aerators thus allowing for greater
finished ceiling height
Up to 4" recess in the slab to

reduce final ceiling height
Allows for vertical/horizontal and
angle movement to simplify
plumbing installation
Allows for aerator positioning in
360 degree radius thus
increasing installation flexibility
No limitation for pipe/aerator
connection (accepts coupler or
welding)
1/4" 5/8" thread sizes available
to meet your requirements
Soil/waste vented aerators
Aerator Adapter
Item No.
Description
00373044
Aerator Adapter
Qty/Pkg
NOTE: To be used in conjunction with 4" CP 680 device
www.us.hilti.com
Concrete Spot Insert
Anchors see page:

8.24
9.9
Firestop Systems
FS-ONE
Technical Data
At 73F (23C) and 50% relative
humidity
High Performance Intumescent Firestop Sealant
Chemical basis
Water-based intumescent acrylic
dispersion
System Advantage /
Customer Benefits
Density
Protects most typical firestop

penetration applications
Easy to work with and fast
cleanup
Can be repenetrated when
laying new cables
Can be painted
Approx. 1.5 g/cm3
Color
Red
Working time
Approx. 20-30 min.
Curing time
Approx. 2mm/3 days
Shore A Hardness
Approx. 50
Movement capability
Approx. 5%
Intumescent Activation
tlk
e0
9^
)&
(/R
84
sod
tc
fm
)v
Z8Z ,ev
64
iJ
53
4i5 23aw djfiw
k
h
u9+ irdwil p3i4e riuh.
12 oi4jt 02 No
oeo f-x 88u WE
-.vb 27
o
vbv uze
h, ir
eiv
Approx 482F (250C)
Expansion rate (unrestricted)

Up to 3-5 times original volume
Temperature resistance (cured)

40F to 212F (40C to 100C)
Application temperature
Product description
Examples
Intumescent (expands when exposed

to fire) firestop sealant that helps
protect combustible and noncombustible penetrations for up to 4
hours fire rating
Sealing around plastic pipe

penetrations in fire rated
construction
Sealing around combustible and
non-combustible
penetrations in fire rated
construction
Product features
Smoke, gas and water resistant
after material has cured
Contains no halogen, solvents or
asbestos
High fire rating properties
Water based, easy to clean
Steel, copper and EMT pipes

Insulated steel and copper pipes
Cable bundles
Closed or vented plastic pipes
HVAC penetrations
For use with
41F to 104F (5C to 40C)
Surface burning characteristics

(ASTM E 84-96)
Flame Spread: 0
Smoke Development: 5
Sound transmission classification

ASTM E 90-97: 56
Approvals
Concrete, masonry, drywall and

wood floor assemblies
Wall and floor assemblies rated
up to 4 hours
Report No. 5071

Listing No. 4485-1200:108
City of New York

MEA 326-96-M Vol. IV
Item No.
Description
Color
00259579 FS-ONE, tube Red

00311387 FS-ONE, foil Red
00259578 FS-ONE, pail Red
Package Contents
Volume
10.1 oz (300 ml)

18 in3
20.2 oz (600 ml) Qty 20 36 in3
5 gal (19 L)
1155 in3
Item No.
Description
00369166
15:1 transfer pump, 2 HP contractor grade compressor, selfcontained, fully portable, operates on 15 Amp outlet. Sold
complete with 2 tapered nozzles,12" flexible extension, 12"
rigid extension, 25' supply hose, variable speed flow gun.
HSSD High Speed Sealant Dispenser*
UL 1479
ASTM E 814
ASTM E 84

approved
FILL, VOID OR CAVITY MATERIAL
FIRESTOP SYSTEMS
66Y7
*HSSD Dispenser and Firestop product available in combo packs. Contact Hilti Customer Service for details.
FM
Not Shown
APPROVED
Item No.
Description
00055205
00024669
CB 200 Pl-300/310 ml Dispenser

600 ml Foil Dispenser
tion
applica
Reduce ost by up to
labor c
60%

www.us.hilti.com
9.10
Firestop Systems
Technical Data
humidity
FS 657
Fire Block
Density
Approx. 0.25 g/cm3
System Advantage /
Customer Benefits
Dimensions (LxWxH)
2"x 5"x 8"
Suitable for re-penetration or

new penetrations
Economical in use with short
installation times
Easy installation as no special tool
is required
Ideal for use in floorsno
forming is required
Smoke resistant
Color
Red
23F to 104F (5C to 40C)
60F to 140F (51C to 60C)
Approx. 572F (300C)

Up to 1:5

(ASTM E 84-96)
Flame Spread Index: 0
Smoke Development Index: 25

54
Approvals
Report No. 5071

Listing No. 4485-1200:106
Product description
City of New York

MEA 325-96-M, Vol. III
Ready-to-use, intumescent flexible

block based on a two-component
polyurethane foam
Product features
UL 1479
ASTM E 814
ASTM E 84
Completely free from dust

and fibers
Halogen, asbestos and solvent
free
Operational immediately after
installation
Can be painted
Sealing single or multiple

penetrations in small to large
openings
Temporary or permanent sealing
of cables and cable tray
penetrations
Temporary or permanent sealing
of insulated and non-insulated
metallic pipes and combustible
pipe penetrations

approved
FIRESTOP SYSTEMS
66Y7
FM
APPROVED
F
Fi
For use with

Walls (UL tested up to max.
opening 52" x 48")
Floors (UL tested up to max.
opening 36" x 36")
Concrete, porous concrete,
masonry and gypsum wall
assemblies
Wall assemblies rated up to

4 hours
Floor assemblies rated up to
3 hours
Examples
Completely dust and fiber-free
rooms and places where
electrical installations are
frequently used, such as
computer centers, hospitals and
laboratories
New buildings in the construction
phase and during renovation
Large openings containing
multiple penetrations as found in
production bays, warehouses,
hospitals etc.
FS 657 Fire Block
www.us.hilti.com
9.11
Item No.
Description
00306241
00306242
00332847
FS 657 Fire Block

Red 80 in3
Blocks
FS 657 Fire BlockCase
Red 2,080 in3 Blocks
FS 657 Fire BlockPallet (18 cases) Red 22 ft3
Blocks
Color
Volume
Type
Qty/Pkg
1
26
468

Firestop Systems
CP 645
Technical Data
humidity
Firestop Wrap Strip
Density
System Advantage /
Customer Benefits
Quick and easy closure without

tools
Ideal for very tight installations
Approx. 1.85 g/cm3
Dimensions (LxWxH)
1/4" x 1" x 25 ft or 1/4" x 2" x 25 ft
Color
Red
Up to 120F (49C)
Approx. 375F (190C)

1:10

(ASTM E 84-96)
Flame Spread Index: 5
Smoke Development Index: 5
Approvals
Iisting No. 4485-1200:118
City of New York

MEA 240-02-M
Product description
For use with
An intumescent, flexible firestop

wrap strip for plastic and insulated
pipe penetrations
Firestopping combustible pipe

penetrations
Difficult applications where space
is limited
Penetrations through concrete
over metal deck
Plastic and insulated penetrations
using PVC, CPVC, ABS and FRPP
Concrete, masonry, wood floor

and gypsum wall assemblies
up to 3 hours
Product features
Highly Intumescent
Long length avoids waste
Can be continuously wrapped
Cost effective
UL 1479
ASTM E 814
ASTM E 84

approved
FIRESTOP SYSTEMS
66Y7
Examples
Waste water pipes
Fresh water pipes
Decking penetrations
FM
APPROVED
CP 645 Wrap Strip

Item No.
Description
Color
Volume
00338975
00338976
00338977
00338978
CP 645, 1" wrap strip

CP 645, 1" wrap 6 pack
CP 645, 2" wrap strip
CP 645, 2" wrap 6 pack
red
red
red
red
1/4" x 1" x 25 ft.

1/4" x 1" x 25 ft.
1/4" x 2" x 25 ft.
1/4" x 2" x 25 ft.
Qty/Pkg
1
6
1
6

www.us.hilti.com
9.12
Firestop Systems
CP 642-160/6" 6.6 8.2 4.4

CP 642-200/8" 8.8 10.0 6.9
CP 642-250/10" 10.8 12.4 9.1
No. of hooks & fasteners
Collar Height (in.)
Collar outside dia. (in.)
Pipe outside dia (in.)
Description
Technical Data
CP 642
Firestop Collar
System Advantage /
Customer Benefits
Snap connection for quick and

easy closure without use of a tool
Adjustable position tabs for
convenient fastening
Ready to use out of the package
6
7
9
Approvals
Report No. 5071

Listing No. 4485-1200:105
City of New York


UL 1479
ASTM E 814
DIN 4102
h.
sc
an
zm
ut
ch
ds
E
an
r
W
o
B
e
N
uz
h.
hriu 88u27 ireiv
jfiw
iJd e02 vbvh,
i4
b
p3 x-.v
jtfoi4
eoo

approved
FIRESTOP DEVICE
FIRESTOP SYSTEMS
5N76
FM
APPROVED
Product description
Galvanized sheet steel containing

sections of intumescent material
(designed to expand when exposed
to fire) for firestopping large
combustible pipes
Sealing of penetrations for

combustible pipes from 6" to 10"
in diameter.
Vented or closed pipe
PVC, CPVC, ABS, FRPP, PVDF
pipes
Wall: two collars, one on each

side
Floor: one collar on underside
(bottom)
Product features
Ready-to-use collar, no
construction required, allowing
fast installation
Adjustable/moveable fastening
tabs
For use with
Examples
Waste water pipes
Fresh water pipes

assemblies and gypsum walls
up to 4 hours

Item No.
Description
00236709*
00310084*
00310085*
CP 642 Firestop Collar-160/6"

00236711
CP 642 Fastening hook
Qty/Pkg
1
1
1
10
* includes fastening hooks
www.us.hilti.com
9.13

Firestop Systems
CP 643
CP 643-50/1.5" 1.42.0
CP 643-63/2" 2.02.5
CP 643-90/3" 2.63.6
CP 643-110/4" 3.64.5
Collar Height (in.)

No. of hooks & fasteners
Quick and easy closure

without tools
Adjustable position tabs
for simple fastening
Low profile for tight installations
Collar outside dia. (in.)
System Advantage /
Customer Benefits
Pipe outside dia (in.)
Firestop Collar
Description
Technical Data
2.8
3.4
4.9
6.0
0.9
1.3
1.7
1.9
2
2
3
3
Approvals
ICBO (International Conference of
Building Officials)
Report No. ER-5071

Listing No. 4485-1200:110
City of New York

h.
sc
an
tzm
hu
sc
E
nd
oW
Bra
h. N uze
hriu 8u27 eiv
CP
djfiw028 bvh, ir
e
v iJ
bv
fm,e p3i4 x-.v
sod 3aw jtf-
2
i4
Z
Z8 irdwilo o
o
k
4i5 12oe
u9+
2
64

UL 1479
ASTM E 814

approved
Product description
A ready-to-use firestop collar, made

of a galvanized steel housing and
intumescent inserts for firestopping
combustible pipes
Firestopping combustible pipes

up to 4" in diameter in
penetrations through fire walls
and floors.
Suitable for the following pipe
materials: PVC, CPVC, ABS,
PVDF, PP and FRPP
Wall: two collars, one on each

side
Floor: one collar on underside
(bottom)
Product features
Adjustable mounting tabs
Ready-to-use collar; no
construction required, allowing
fast installation
Example
FIRESTOP DEVICE
FIRESTOP SYSTEMS
5N76
FM
APPROVED
Waste water pipes

Fresh water pipes
For use with

and gypsum wall assemblies
up to 4 hours

Item No.
Description
00307707*
00307708*
00307709*
00307710*
00307701
CP 643 Firestop Collar CP 643-50/1.5"

CP 643 Firestop Collar CP 643-63/2"
CP 643 Fastening Hook
Qty/Pkg
1
1
1
1
30
* includes fastening hooks

www.us.hilti.com
9.14
Firestop Systems
Technical Data
humidity
Density
Approx. 9 lb/gal (1.27 g/cm3)
CP 672
Speed Spray
Your Complete Top-of-Wall Firestopping Solution!
Color
System Advantage /
Customer Benefits
Red
Maximum flexibility, exceeds 500

cycle requirements (Class II & III
Approval) (UL 2079 &
ASTM E 1399)
Save time and money using the
Spray Tech EP2510 Sprayer for
quick and easy installation
CP 672 Speed Spray contains no
halogens, solvents or asbestos so
it is safe to use and wont harm
the environment
Water based formulation so spills
and over-spray cleanup quick and
easy
40F to 90F (5C to 32C)
Temperature Resistance
35F to 120F (2C to 49C)
Consistency
Sprayable liquid
Chemical basis
Latex based dispersion
Working time
30-45 minutes
Curing time
24 hrs
Ph-value
Firestop
System
Approx. 8.0
Movement capability
Approx. 50%

(ASTM E 84-00)
Flame spread: 5
Smoke development: 0

(ASTM E 90-00)
55
Approvals
Report No. ER-5614

Listing No. 1451-1200:114
Listing No. 1452-1200:109
Product description
Examples
A sprayable fire-rated mastic for

construction joints where maximum
movement is required
Top-of-wall joints
Curtain wall / Edge of slab
Expansion joints
Where a gypsum wall assembly

meets the underside of a metal
or concrete deck
Where a concrete floor assembly
meets with non-rated exterior
wall (concrete, glass, etc.)
Where two concrete floor/wall
assemblies meet
Product features
Contains no halogens, solvents or
asbestos
Water based, easy to clean
Sprayable or apply by brush
For use with

Concrete, masonry and gypsum
wall assemblies
Wall and floor / wall assemblies
rated up to 4 hours
City of New York

MEA 99-99-M, Vol.III

UL 2079
ASTM E 1399
ASTM E 84
CP 672 Speed Spray

Item No.
Description
Color
Volume
00377230
CP 672 Speed Spray, pail 5 gal (19 L)
red
1155 in3 Pail
Type
00304540
Spray Tech EP2510 Firestop Sprayer
Qty/Pkg

approved
FOR USE IN JOINT SYSTEMS
66Y7
FM
APPROVED
EP 2510
Airless Sprayer
www.us.hilti.com

Speed Strips see page:
9.16
9.15
Firestop Systems
CP 767 & CP 777

CP 767 Speed Strips & CP 777 Speed Plugs
Complete Top-of-Wall Firestopping Solution when used with CP 672 Speed Spray
System Advantage / Customer
Benefits
Pre-cutleaves no gaps or voids

Smooth surface provides cost
effective spray coverage
Safe to useno asbestos /
inorganic, will not mildew
Up to 60% faster than castle
cutting!
Technical Data
Density
CP 777: 6 pcf
CP 767: 4 pcf

approved
FORMING MATERIAL
17RL
Complete Top-of-Wall
Firestopping Solution
when used with
CP 672 Speed Spray
Firestop
System
Product description
Product features
Tested and approved
Pre-formed mineral wool strips for

1.5", 2" and 3" decks
Pre-cut to industry standard size

decking flutes
Reduces material waste
3 sizes available
UL Classified when used in

conjunction with CP 606 flexible
firestop, CP 601S or CP 672
Speed Spray
Top of wall
Easy One step installation...

Simply cut to length and install.
Full Coverage Pre-cut flute configuration

leaves no gaps or voids.
Superior Finish Smooth surface allows for

quick and cost effective coverage with Hilti Speed
Spray.
Saves Time and Money!

Castle Cutting
Conventional Mineral Wool
Hilti Speed Plugs
50 MINUTES
35 MINUTES
20 MINUTES
60% Faster than Castle Cutting

43% Faster than Conventional Mineral Wool
*Based upon 40 linear feet of installation
CP 677 Speed Plugs

Item No.
Description
Flute Dimensions (H x Flute x L)
00371925
00340998
00340999
CP 777 1.5" Speed Plug

CP 777 2" Speed Plug
CP 777 3" Speed Plug
1.5" x 3.5" x 4.5" x 36"

2" x 4.5" x 5.5" x 36"
3" x 5" x 7" x 36"
Qty/Pkg
18
18
18
CP 767 Speed Strips

Item No.
Description
Strip Dimensions (W x H x L)
00374507
00374508
00374505
00374506
CP 767 2" Speed Strips (1 Hour)

2" x 0.625" x 36"

2" x 1.25" x 36"
4" x 0.625" x 36"
4" x 1.25" x 36"
Qty/Pkg
84
42
42
21

www.us.hilti.com
CP 672 Speed Spray
see page:
9.15
Dispenser EP2510
see page:
9.15
9.16
Firestop Systems
Technical Data
humidity
CP 601S
Elastomeric Firestop Sealant
Density
Approx. 1.4 g/cm3
System Advantage /
Customer Benefits
Color
Red
Simple use and application

Good adhesion without use of
a primer
Smoke, fume and water resistant
Excellent movement capability,
meets 500 cycle requirements
(UL 2079 & ASTM E 1399)
40F to 104F (5C to 40C)
Skin-forming time
Approx. 15 min.
Curing rate
Approx. 2mm/3 days
Volume shrinkage
Approx. 0 5%
Movement capability
Approx. 25%
40F to 320F (40C to 160C)

(ASTM E 84-96)
Flame spread: 0
Sound transmission
classification
(ASTM E 90-97)
50
Approvals
Report No. ER-5614

Listing No. 1451-1200:115
Listing No. 1452-1200:113
Product description
Examples
A silicone based firestop sealant

that provides maximum movement
in fire-rated joint applications and
pipe penetrations
Sealing construction/expansion
joints
Top-of-wall joints
Metal pipes
Cable bundles
HVAC penetrations*

or concrete deck
Sealing expansion joints to
impede the passage of fire,
smoke and toxic fumes
Sealing HVAC penetrations
through fire-rated assemblies
Product features
Halogen and solvent free
Weather and UV-resistant
Asbestos free
City of New York

MEA 101-99-M, Vol. IV

UL 2079
ASTM E 1399
UL 1479
ASTM E 814
ASTM C 920
ASTM E 84
For use with

Various base materials such
as masonry, concrete, metal,
glass, etc.
up to 4 hours

approved
66Y7
FM
Item No.
Description
Color
Volume
00314268
00314269
00314270
CP 601S, tubes 10.5oz (310 ml)

CP 601S, foil 20.2oz (600 ml)
CP 601S, pail 5 gal (19 L)
red
red
red
18 in3
Tube
36 in3
Foil
1155 in3 Pail
Type
00055205
00055205

Qty/Pkg
1
20
1
1
1
APPROVED
www.us.hilti.com
* For metal ducts with damper, consult damper manufacturer.

9.24
9.17
Firestop Systems
CP 604
Technical Data
humidity
Self-Leveling Firestop Sealant
Chemical basis
System Advantage /
Customer Benefits

(ASTM E 1399 & UL 2079)
Smoke, fumes and water resistant
Neutral elastic silicone
Density
Approx. 1.35 g/cm3
Color
Gray
40F to 104F (5C to 40C)
4F to 248F (20C to 120C)
Curing time
Approx. 5 mm/3 days
Tensile strength (modulus of

elasticity)
Approx. 0.7 N/mm2
Shore A Hardness
Approx. +20%
Joint movement capability

Approx. +20%
Product description
For use with
Self-leveling, single-component,
silicone-based firestop sealant for
use with through-penetrations as
well as construction joints in floors.
joints
Metal pipes
Cable bundles
Sealing multiple penetrations in
small or large openings
Concrete floors rated up to 3 hours
Product features
Self-levelingrequires no tooling
Excellent elongation/compression
properties
Resistant to smoke and water
Approvals
In progress, call for details
Examples
Penetrations for metal pipes

between floor levels
Construction joints and expansion
joints in floors
Listing No. 4485-1200:117
City of New York

MEA 237-02-M

UL 1479
UL 2079
ASTM E 1399
ASTM E 814
ASTM E 84 (testing in progress)

approved
CP 604 Firestop Self-leveling Firestop Sealant

Item No.
Description
Color
Volume
00369637
00369177
CP 604, Foil 20.2 oz (600 mL)

CP 604, Pail 4 gal
gray 36 in3
gray 924 in3
00024669
600 mL Foil Dispenser
Type
Foil
Pail

FIRESTOP SYSTEMS AND JOINT SYSTEMS
66Y7
Qty/Pkg
12
1
1
FM
APPROVED

www.us.hilti.com
9.24
9.18
Firestop Systems
Technical Data
humidity
CP 620
Fire Foam
Color
Red
System Advantage /
Customer Benefits
Cartridge content
10.1 oz (300 ml)
Fire Foam Yield

Up to 110 in
CP 620
One solution for various

applications
Easy handling for difficult to reach
applications
One step application
Paintable
Virtually impervious to smoke
Bacteria resistant
No additional materials required
Saves time and money
Brands
chutzb
esc
hichtu
sodfm,e
ng
v iJdjfiwh
riuh. No
WE
4i5kirdw
u9+12 iloi4jtf-x-.v
bvbvh,
oeoo
ireiv
50F to 86F (10C to 30C)
Temperature resistance of cured

foam
22F to 212F (30C to 100C)
Minimum temperature
Substrate 32F (0C)
Cartridge 50F (10C)
Curing
Non-tacky after Approx. 35 seconds
Ready to cut after Approx. 1 minute
Thermal insulation (R-value)

2.83.0 per inch of thickness
Sound transmission
classification (ASTM E 90-97)
50
Structure-borne sound
insulation
Pipe/wall 3050%

(ASTM E 84-01)
Flame spread: 0
Approvals
Product description
Innovative firestopping solution for

complex applications
Sealing small- to medium-sized

openings
Permanent fire seal for cables
and cable trays
Permanent fire seal for noncombustible pipes
Permanent fire seal for
combustible pipes when used in
conjunction with CP 645 Wrap
Strips
Permanent fire seal where
cables, steel, copper, cast iron or
plastic pipes all pass through the
same opening
Product features
Up to 6 times expansion
Repenetrable
Cures within 60 seconds
In progress, please call for details

Listing No. 4485-1200:119
City of New York

MEA 238-02-M
For use with

floor and wall assemblies
Floor and wall assemblies
Concrete, drywall, masonry
Examples
Power cables and cables of
various types and diameters
Non-combustible pipes (steel,
cast iron, copper)
Combustible pipes when
used in conjunction with
CP 645 Wrap Strips

UL 1479
ASTM E 814
ASTM E 84

approved
FIRESTOP SYSTEMS AND JOINT SYSTEMS
66Y7
FM
CP 620 Fire Foam

Item No.
Description
00369757
CP 620 Fire Foam 10.2 oz (300 ml)
Qty/Pkg
00338720
Dispenser
00371883
CP 620 Deluxe Starter Kit
Includes 2 mixers and 1 extension pipe per cartridge
Includes 1 dispenser, 9 cartridges, 18 mixers and

9 extension pipes in Hilti case
APPROVED
00338718
00338716
CP 620-M Mixer
CP 620-Ext Extension pipe
12
12
www.us.hilti.com
9.19

Firestop Systems
CP 606
Technical Data
humidity
Flexible Firestop Sealant
Chemical basis
System Advantage /
Customer Benefits
Paintable
(ASTM E 1399 & UL 2079)
Smoke, fume and water resistant
Easy clean up with water
Acrylic based firestop sealant
Density
Approx. 1.5 g/cm3
Color
Red or white
40F to 104F (5C to 40C)
Skin-forming time
Approx. 15 min
Curing rate
Approx. 2mm/3 days
Volume shrinkage
Less than 20%
Movement capability
Approx. 10%
22F to 176F (30C to 80C)

(ASTM E 84-96)
Flame Spread: 0
Smoke Development: 5
Product description
Examples
An acrylic based firestop sealant

that provides movement capability in
fire rated joint applications
joints
Top-of-wall joints
Metal pipes
Cable bundles
HVAC penetrations*

or concrete deck
Sealing expansion joints to
impede the passage of fire,
smoke and toxic fumes
Sealing around HVAC
penetrations through fire-rated
assemblies
Product features
Silicone free
Halogen, asbestos and
solvent free
UV-resistant
For use with

Various base materials such as
masonry, concrete, metal, etc.
up to 3 hours

ASTM E 90-97
50
Approvals
Report No. ER-5614

Listing no. 1452-1200:112
City of New York

MEA 100-99-M, Vol. IV

UL 2079
ASTM E 1399
UL 1479
ASTM E 814
ASTM E 84

approved
Item No.
Description
Color
Volume
00337191
00314272
00337192
00337193
CP 606, Tube10.5oz (310 mL)

CP 606, Foil 19.6oz (580 mL)
CP 606, Foil 19.6oz (580 mL)
CP 606, Pail 5 gal (19 L)
red 18 in3
white 36 in3
red 36 in3
red 1155 in3
Type
Tube
Foil
Foil
Pail

66Y7
Qty/Pkg
1
20
20
1
FM
APPROVED
00055205
00024669

600 ml Foil Dispenser
* For metal ducts with damper, consult damper manufacturer.

www.us.hilti.com
9.24
9.20
Firestop Systems
Technical Data
humidity
CP 637
Firestop Mortar
Application temperature (ideal)

40F to 110F (5C to 43C)
System Advantage /
Customer Benefits
Color
Light red
Saves time
Versatile
Form removal
(depending on consistency)
Approx. 2 hours
Density
Approx. 40.6 pcf (dry)
Expansion on setting (approx.)

0.08%
Compressive strength
24 hrs
After Casting
Pourable 360 psi
(2.5 N/mm2)
Plastic 610 psi
(4.2 N/mm2)
Stiff
870 psi
(6.0 N/mm2)
After
Full Cure
725 psi
(5.0 N/mm2)
1200 psi
(8.3 N/mm2)
1784 psi
(12.3 N/mm2)

(ASTM E 84-01)
Flame spread: 5
Yield (30 lb pail)

900-1000 cubic inches depending on
mix ratio
Approvals
4485-1200:120
City of New York

MEA 239-02-M
Product description
Examples
Fire-resistant, mortar suitable for

firestopping large openings
Sealing medium-sized to large

openings with non-combustible
pipes or cable trays
Permanent fire seal for cables,
cable trays and non-combustible
pipes
Large openings containing

multiple steel, conduit and EMT
pipes
Large openings with single or
multiple cable tray applications
Product features
Quick-settingforms can be
removed in as little as 2 hours
Superior working properties
Can be used in horizontal or
vertical applications
ASTM E 814
UL 1479
ASTM E 84
For use with

Concrete and masonry
assemblies
Walls and floors rated up to
4-hours

approved
FIRESTOP SYSTEMS
SEE UL/cUL FIRE RESISTANCE DIRECTORY
66Y7
www.us.hilti.com
9.21
CP 637 Firestop Mortar

Item No.
Description
Color
Type
00340645
00307587
00307588
00332849
CP 637 Firestop Mortar, Pail 30 lb

Lt. red
Lt. red
Lt. red
Lt. red
Pail
Pail
Pail
Pail
Qty/Pkg
1
18
27
54

Firestop Systems
CP 617, CP 617L & CP 617XL
Technical Data
humidity
Firestop Putty Pad
Dimensions (LxWxH)
System Advantage /
Customer Benefits
Applied by hand
Fast installation
CP 617:
6" X 7" X 1/8" (15 X 18 X 0.3 cm)
CP 617L:
7" X 7" X 1/8" (18 X 18 X 0.3 cm)
CP 617XL:
9" X 9" X 1/8" (23 X 23 X 0.3 cm)
Consistency
Moldable putty
Color
Red
40F to 95F (5C to 35C)
Storage temperature
40F to 104F (5C to 40C)
Cure
Non-curing
Density
1.48 g/cm3
Approx. 220F to 250F
(104C to 121C)
Volatile solvents
None
Product description
Examples
Asbestos fibers
An intumescent moldable firestop

putty designed to help protect
Protection of
Where two outlets are within a

single stud/cavity or within 24"
(not back to back)

(ASTM E 84-96)
Product features
Gypsum wall assemblies with

wood or metal studs
Applied by hand
Fast installation
For use with
None
Flame Spread: 5
Sound transmission
classification
(ASTM E 90-97)
49
Approvals
City of New York
MEA 102-99-M

UL 263
ASTM E 84
CP 617 Firestop Putty Pad

Item No.
Description
Color
Area
00309760
00333583
00000000
CP 617 Putty Pad 6" X 7"

red 42 in2 per pad (840 in2 total)
CP 617L Putty Pad 7" X 7" red 49 in2 per pad (980 in2 total)
CP 617XL Putty Pad 9" X 9" red 81 in2 per pad (1620 in2 total)
Qty/Pkg

approved
20
20
20
WALL OPENING PROTECTIVE MATERIAL

FIRE RESISTANCE CLASSIFICATION
SEE PRODUCT CATEGORY IN
UL FIRE RESISTANCE DIRECTORY
66Y7
FM
APPROVED

www.us.hilti.com
9.22
Firestop Systems
Technical Data
humidity
CP 618
Firestop Putty Stick
Dimensions
18 in3
System Advantage /
Customer Benefits
Consistency
Moldable putty
Reusable
Easy to add or subtract cables
Fast installation
Color
Red
40F (5C) to 95F (35C)
Cure
Non-curing
Density
Approx. 1.48 g/cm3
Approx. 220F to 250F
(104C to 121C)

(ASTM E 84-96)
Flame Spread: 5

(ASTM E 90-97)
49
Approvals
Report No. ER-5071

Listing No. 4485-1200:111
City of New York
Product description
Examples
An intumescent, non-hardening,
firestop putty for cable and pipe
penetrations
Single or bundled cables

Non-combustible pipe
Blank openings
Where telecommunication and

data lines penetrate
gypsum wall assemblies
Where steel conduit and EMT
penetrate concrete
and block wall assemblies
Where blank openings exist in
concrete and block
wall assemblies
Product features
For use with
Contains no volatile solvents or

asbestos
Water resistant
Easy to re-penetrate
Concrete, masonry and gypsum

wall assemblies
up to 3 hours
MEA-98-99-M, Vol.III

UL 1479
ASTM E 814
ASTM E 84

approved
FIRESTOP SYSTEMS
SEE PRODUCT CATEGORY IN
UL FIRE RESISTANCE DIRECTORY
66Y7
CP 618 Firestop Putty Stick

Item No.
Description
00314721
CP 618 Putty Stick red 18 in3 per stick (216 in3 total)
Color
Volume
Qty (sticks)
12
FM
APPROVED
www.us.hilti.com
9.23

Firestop Accessories
Dispensers
Foil
Item No.
Description
00024669
00334548
00220139
Tube
Foil Pack (600 mL) Dispenser

Foil Pack (600 mL) Dispenser Replacement Nut
Nozzles for Foil Pack (10/pkg)
Item No.
Description
00055205
00024825
Bulk
300/310 mL Dispenser (CB 200 Pl)

300/310 mL Dispenser (Standard)
Item No.
Description
09645002
98450020
09645004
Bulk Caulk Gun

Force Flow Bulk Loader
Follow Plate
Pneumatic Foil Pack Dispenser

Size: Barrel 20-1/2", Handle 7" X 4-1/2" X 1-1/2"
NEW!
Item No.
Description
00374502
00334548
00220139
00374504
Pneumatic Dispenser
Screw Cap Replacement

Clear Plastic Nozzle CS-280-D5 (10/pk)
Floating Plunger Assembly and Quick Exaust Valve Repair Kit
High Speed Sealant Dispenser (HSSD)

Dispenser
Item No.
Description
00369166
HSSD High Speed Sealant Dispenser*
15:1 transfer pump, 2 HP contractor grade compressor, self-contained,

fully portable, operates on 15 Amp outlet. Sold complete with 2 tapered
nozzles,12" flexible extension, 12" rigid extension, 25' supply hose,
variable speed flow gun.
*HSSD Dispenser and Firestop product available in combo packs. Contact Hilti Customer Service for details.
Tip Assemblies for HSSD Dispenser

Item No.
Description
00297225
00297425
0.225 Tip Assembly

0.425 Tip Assembly
tion
applica
Reduce ost by up to
labor c
60%
Airless Sprayer EP 2510

Item No.
Description
00334123
00376840
00376841
00376844
00376843
00376842
00304541
00304542
00304543
00304544
Spray Tech Sprayer EP 2510 CSA Approved

Spray Tech EP 2510 Sprayer Tip (.425)
Spray Tech EP 2510 Sprayer Tip (.225)
Spray Tech Sprayer EP 2510 Tip (.427)
Spray Tech EP 2510 Sprayer 3' X 1/4" Whip Hose
Spray Tech EP 2510 3/8" X 1/4" Fitting
Spray Tech Combo W/18 Pails
As Shown
www.us.hilti.com
9.24
Firestop Accessories
Indentification
Item No.
Description
00306219
00339611
Hilti Firestop System Identification Plate

Hilti Firestop Identification Stickers (100 stickers/roll)
Miscellaneous
Item No.
Description
00024155
Stainless Steel Mixing Paddle
Qty/Pkg
00236993
00029410
00029783
Mineral Wool
Retaining Collar
Collar Clamps 4" diameter
1
18,432 in3
(1) 25 ft. Roll
10
Insta-Back Fire-Rated Drywall Repair System

Item No.
Description
00068450
00068454

Qty/Pkg
200
200
Installation instructions for Insta-Back Fastener

1. Position Insta-Back
clip as per product
instructions.
2. Join drywall over
clips.
3. Break off tabs.
www.us.hilti.com
9.25
Notes
Firestop Design Center online
System design search by through-penetration
or joint application
Direct link to Hilti Tech Center for additional
technical information about Hilti products
Search for UL System drawings by number
Firestop Terms & Definitions
Project References
Firestop FAQs
UL Nomenclature
Engineering Judgments
Fire Protection Triangle
Building, Regulations & Codes
CSI Format Specifications
UL Drawing Schedules
Submittal Toolkit
Firestop Detail Sheets
Online Design Center

www.us.hilti.com/firestopdc
9.26
Hilti Foam & Construction Chemical Systems
Foam & Construction Chemical Systems

Foams
Insulating Foam CF 128-DW
Filler Foam CF 511
Grip Filler Foam CF 116
Page 10.6
Page 10.7
Page 10.8
Construction Adhesives
General Purpose CA 3200
Heavy Duty Subfloor CA 3400
High Performance Water-Based CA 3600
Page 10.9
Page 10.10
Page 10.11
Concrete Repair Products

Crack Injection System CI 060 EP
Repair Mortar RM 700 EP
Repair Mortar RM 710 EP
Repair Mortar RM 800 PC
Page 10.12
Page 10.13
Page 10.13
Page 10.14
Cementitious Grout
Cementitious Grout CG 200 PC
Page 10.15
Sealers
Pavement Joint Sealant CS 300 EP
Clear Epoxy Sealer CC 400 EP
Gray Epoxy Skidproofer CC 410 EP
Page 10.16
Page 10.17
Page 10.18
Cleansers & Degreasers

So-Safe Graffitti Remover
Biodegradable Cleaner MC 200
Biodegreaser MC 300
Waterless Hand Cleaner MC 400
Page 10.19
Page 10.19
Page 10.19
Page 10.19

System
CF 128-DW
Insulating Foam
Description/Feature
Page
CF 128-DW is a CFC-free, one-component polyurethane insulating foam for

insulating residential and commercial structures from air, dirt, sound and pest
infiltration. CF 128-DW is suitable for indoor use. Its low expansion
characteristics make it perfect for insulating around doors and windows
10.6
Features
Contains no CFCs
Meets Class I fire-rated building specs
Contains no urea formaldehyde or PCBs
Physiologically harmless when fully cured
CF 511
Filler Foam
CF 511 is the first gun foam introduced on the market that has the ability of
performing at and below freezing. The CF 511 formula is designed to be used for
sealing and insulating residential and commercial structures against air, dirt,
sound and pest infiltration.
10.7
Foams
Features
Low temperature performance allows the CF 511 to be applied in cold
weather conditions
Enhanced performance characteristics allow foam to cure at freezing without
bubbling or becoming brittle
CF 116
Grip Filler Foam
CF 116 is a single-component polyurethane-based filling foam. The can is

equipped with a precision valve (gold valve).
10.8
Features
HFC propellant
Meets Class I fire-rated building specs
Physiologically harmless when fully cured
Neutral Odor
Does not rot or deteriorate with age if protected from direct UV exposure
CA 3200
General Purpose Construction Adhesive
CA 3200 bonds to most common building materials including: wood, metal,

plaster, concrete, drywall, acoustical panels, paneling, tileboard, trim, corkboard
and polyurethane foam.
Features
Bonds polyurethane foam
Water-resistant bond
Strong initial tack
Automatic shimming
CA 3400
Heavy Duty Subfloor Adhesive
Stays resilient
Will not freeze
Freeze/thaw stable
Water resistant
CA 3400 bonds securely to: wood, plywood, fiberboard, hardboard, concrete,

masonry, stone, tile, marble, acoustical material and most other common building
materials.
10.10
Features
Reduces nailing, helps prevent squeaky floors
Bridges to 3/8 in.
PFS tested to APA AFG-01
High strength, Water-resistant bond
Will not become brittle or hard
Suitable for hot and cold gunning
CA 3600
High Performance Water Based
Construction Adhesive
CA 3600 provides superior adhesion in a water based formulation

for most common building materials including:
Wood
Wet, Frozen or Treated lumber
Waferboard
Paneling
Ceramic or Acoustical Tile
Corian
Concrete
Most Porous substrates
Polyurethane or Polystyrene Foam
Features
Lowest VOC content available
Non-toxic, non-flammable
Weather resistant
10.3
10.9
10.11
Superior bonding strength

Solvent free
PFS tested to APA AFG-01 specs.

System
CI 060 EP
Crack Injection System
Description/Feature
Page
Features
10.12
RM 700 EP
Concrete Repair System
Repair Mortar
RM 710 EP
Repair Mortar
RM 800 PC
Repair Mortar
Concrete columns, beams, floor slabs, and walls

Basement walls
Swimming pools
Cracks in large concrete structures, such as parking garages, grain silos,
bridges, and containment walls
100% solids epoxy
Self-contained cartridge with resin and hardener in a single package
Non-return valves in ports and injection hoses help eliminate spills
No expensive equipment required
Tenacious adhesion, chemical resistance and excellent weatherability makes

RM 700 EP Repair Mortar suitable for a variety of repair work:
Repairs to floor slabs, ramps, expansion joint edges
Replacement of chemically attacked concrete.
Concrete exposed to extreme weather conditions, i.e. freeze/thaw cycles,
constant moisture
Concrete in high traffic areas such as warehouse floors, loading docks,
driveways, etc.
Concrete subject to chloride (salt) or sulfate attack
For interior applications where a faster cure or applications at lower
temperatures are required, use RM 710 EP
10.13
Tenacious adhesion, chemical resistance and excellent weatherability makes

RM 710 EP Repair Mortar suitable for a variety of repair work at lower temperatures:
Repairs to floor slabs, ramps, expansion joint edges
Replacement of chemically attacked concrete.
Concrete exposed to extreme weather conditions, i.e. freeze/thaw cycles,
constant moisture
Concrete in high traffic areas such as warehouse floors, loading docks,
driveways, etc.
Concrete subject to chloride (salt) or sulfate attack
Areas where water based latex type patching compounds have failed
10.13
The fast cure, primerless adhesion and durability of RM 800 PC makes it suitable
wherever pedestrian and vehicular traffic are anticipated.
Roadways
Runways and taxiways
Bridges
Parking structures
Warehouse floors
Loading docks
Setting posts, railings and parking meters
10.14
Other Concrete Repair and Coating Products Available from Hilti

These items are available by special order. Contact your Hilti representative or our Customer Service Department
for ordering procedures, lead times and pricing. 1-800-879-8000
Application
Hilti Product
Heavy duty interior floor coating
CC 99 EP 100% Solids Epoxy
Heavy duty exterior coating, abrasion and chemical resistant
CC 321 UR Polyurethane
CC 324 UR V.O.C. Compliant Polyurethane
Acid-resistant floor coating
CC 251 EP Novolac Epoxy
Sub-zero floor repairs
RM 720 EP Epoxy Repair Mortar
Vertical concrete repairs
RM 705 EP Epoxy Gel Repair Mortar
Fast set concrete repairs
RM 800 PC Rapid-Set Portland Cement Repair Mortar
Epoxy grout for heavy or vibrating loads
CG 500 EP High-strength Epoxy Grout
Water activated injection foam seals underground leaking
HPC 111 Hydrophilic Injection Resin
10.4

System
CG 200 PC
Cementitious Grout
CS 300 EP
Sealers / Cementitious Grout
Pavement Joint Sealant
Description/Feature
CG 200 PC is a non-metallic, non-corrosive and non-shrink portland cement

grout. CG 200 PC is designed for applications where high fluid mixes and
compressive strengths in excess of 10,000 psi are desired. CG 200 PC is
suitable for use in the grouting of heavy equipment and machinery, concrete
and structural steel columns, anchors and bearing plates, as well as grouting
and leveling precast and prestressed members.
CS 300 EP is a two component polymer hybrid containing both urethane and

epoxy resins in order to provide a resilient filler for control joints in pavement and
floors. This unique chemistry allows excellent flexural strength and elongation
while maintaining high tensile strength. The epoxy/urethane blend exhibits
excellent adhesion, which results in a long lasting, durable repair.
Page
10.15
10.16
CS 300 EP is designed for sawcut or cast joints in floors and pavement. It is

recommended for use on highways, bridges, airports, garages, industrial floors,
and marine decks.
CC 400 EP
Clear Epoxy Sealer
CC 400 EP is a USDA approved two-component water based clear epoxypolyamide sealer used to protect concrete surfaces from dusting and enhance
the cleanability of floors.
10.17
Because CC 400 EP is water based, there is no strong solvent odor, and

CC 400 EP is V.O.C. compliant in New York, New Jersey and California.
CC 410 EP
Gray Epoxy Skidproofer
CC 410 EP is a USDA approved two-component water based gray epoxypolyamide skid proofer, used to help protect concrete surfaces from wear and
to minimize the likelihood of slipping on wet floors.
10.18
Because CC 410 EP is water based, there is no strong solvent odor, and CC 410
EP is V.O.C. compliant in New York, New Jersey and California. Unlike many other
water based coatings, CC 410 EP performs as a durable, wear resistant sealer.
So-Safe
Graffiti Remover System
So-Safe Graffiti RemoverLight Duty Liquid

This liquid formulation is designed to safely remove spray paint, marker, pen,
glue, and grease from non-porous materials without affecting most surfaces.
Suitable for graffiti removal from painted surfaces such as signs, as well as
stainless steel and most plastic surfaces.
10.19
Maintenance Chamicals
So-Safe Graffiti RemoverHeavy Duty Sprayable Gel

This gel formulation is designed to safely remove spray paint, marker, pen, glue, and
grease from porous surfaces and for difficult-to-remove graffiti on non-porous surfaces.
Suitable for graffiti removal from uncoated concrete, hollow block and masonry.
MC 200
Biodegradable Cleaner
MC 300
Biodegreaser
10.19
MC 300 Biodegreaser
MC 300 is a citrus-based, biodegradable degreaser designed to clean grease,
grime and soap scum, lift oil from concrete and help maintain grease traps.
MC 400
Waterless Hand Cleaner
10.5
MC 200 Biodegradable Cleaner

MC 200 is a non-flammable, biodegradable, all purpose cleaner designed for use
on plastic, metal and other surfaces. MC 200 removes grease, oil scum, ink,
wax, dirt and soil from floors, printing presses, lathes, milling machines,
machining equipment, shower stalls and many other areas.
MC 400 Waterless Hand Cleaner

MC 400 is a creamy, protective hand cleaner. This product may be used with or
without water to remove grease, grime, oil, tar, ink, paint, moly, asphalt, carbon,
putty adhesives and other soils.
10.19
Foams
CF 128-DW Insulating Foam
Technical Data
All data measured at 73F (23C) and
55% relative humidity
Main applications Insulating
Window frames and sills

Around doors
Floor/Wall joints
Electrical junction boxes
Attics
Refrigeration units and pipes
Air conditioning systems
Filling
Product description
System advantages
CF 128-DW is a CFC-free, onecomponent polyurethane filler foam

for sealing residential, commercial
and industrial structures from air,
dirt, sound and pest infiltration. CF
128-DW contains no urea
formaldehyde and is suitable for
indoor use.
CF 128-DW Insulating Foam
combined with the CF-DS1
Dispenser provides precise metering
of product, stop-and-go capability
and long service life for the
professional user.
Minimal expansion of foam

reduces warping pressure on
doors and windows
High yield of 1.55 ft3 provides
more foam per can than
competitive foams
Precision dispenser allows for
exact placement of foam without
waste
Adjustment knob allows for
accurate control of bead to as
small as 1/8 inch
Hardened steel dispenser tip for
longer life
Precision plastic valve prevents
pressure loss, prolongs shelf life
and prevents waste
Breaches in walls
Pipe penetrations in
non-fire-rated walls
Voids in concrete forms
Underground utility ductwork
Foam can contents

24 oz (680 g)
Color
white-yellow
Foam yield per 24 oz can

approx. 1.55 ft3 (44L)
Approximate cure schedule

Non tacky: After approx. 810 min
Ready to cut: After approx. 25 min
Tensile strength
11 psi (7.5 N/cm2)
Shear strength
5 psi (3.5 N/cm2)
(10% compression): 8 psi (5 N/cm2)
Dimensional stability (up to

104F (40C) and 90% r.h.)
10%
Product features
Gross density foamed freely
Contains no CFCs
Meets Class I fire-rated
building specs
Contains no urea formaldehyde
or PCBs
Physiologically harmless when fully
cured
Neutral odor
Does not rot or deteriorate with
age if protected from direct U.V.
exposure
1.5 lb/ft3 (17 kg/m3)

foam
22F to 176F (30C to 80C)
Ideal application temperature

59F to 90F (15C to 32C)
Possible application temp. range

50F to 96F (10C to 35C)
Min. temp.
substrate/ambient/can
41F (5C)
Building material class

Class A
Shelf life from date of

manufacture (when stored at
68F (20C)
12 months
Item No.
Description
00338255
CF 128-DW Insulating Foam 24 oz can
00336256
CF 128-DW Insulating Foam Case of 12 cans
Foam Combo Items
Item No.
Description
00338643
CF 128 Foam Kit Complete
Caulking and Sealants

Surface Burning characteristics
Applied to inorganic
reinforced cement board +
Flame Spread 10
Smoke Developed 35
+ - Tested as applied in three 3/4 in. diameter beads
5 in. on center
covering 12.5 percent of the exposed test sample area.
Includes 3 cans of CF 128-DW Foam, 1 CF-DS1 Dispenser,1 CF-R1 Cleaner and Hilti
Case
Bulk: Foam only

Item No.
Description
00338257
CF 128-DW Foam: 9 cases
00338258
00338259
Combo: Foam + Dispenser
00338573
CF 128-DW Foam: 3 Cases with 1 CF-DS1 Dispenser
00338574
CF 128-DW Foam: 6 Cases with 1 CF-DS1 Dispenser
00338575
CF 128-DW Foam: 9 Cases with 2 CF-DS1 Dispensers
00338576
CF 128-DW Foam: 16 Cases with 2 CF-DS1 Dispensers
00338577
CF 128-DW Foam: 32 Cases (1 Pallet) with 4 CF-DS1 Dispensers
00338578
CF 128-DW Foam: 64 Cases (2 Pallets) with 8 CF-DS1 Dispensers
Dispenser
Item No.
Description
00259768
00313187
00311512
Accessories
CF-DS1 Dispenser
P20-600K Extra Long Dispenser (with 27" barrel)
CF & EX/DS Plastic Nozzel Tip
Item No.
Description
00024631
00311111
CF-R1 Cleaner: 17oz (500 mL) can

Foam Kit Box Empty
ADDED
VALUE
Case Study #510103*

Project Planner/Engineer
$4,800 annual
clean-up labor
savings using Hilti
CF 128-DW Insulating
Foam to seal seams in
concrete forms around
steel columns to
prevent slurry runthrough, greatly
reducing clean-up.

www.us.hilti.com
10.6
Foams
Technical Data
CF 511 Filler Foam
Foam can contents
Main Applications
Filling
24 oz (624 g)
Foam yield per can
Insulating
Around mechanical/electrical
penetrations through wood studs
Voids in concrete form work
Breaches in walls
Repair areas in drywall before
coating of drywall mud
1.59 ft (45 L)
3
Application temperatures
20F to 80F (6C to 27C)

Non tacky after approx. 10 to 15 min,
Ready to cut after approx. 30 min
Tensile strength
11 psi
Floor/Wall joints
Electrical junction boxes
Attics
Refrigeration units and pipes
Air conditioning systems
Adhesion
Adhere drywall to stud framing
per ASTM D 6464-99
Shear strength
5 psi
8 psi
Dimensional stability
10%
Gross density foamed freely

1.06 lb/ft3
Building material class

Class A

foam
22F to 176F (30C to 80C)
Flame spread
5
Smoke developed
30

manufacture
12 months

UL 723
ASTM E90
ASTM D 6464-99

approved
Flame Spread 5
Smoke Developed 30
5 in. on center covering 12.5 percent
of the exposed test sample area.
Product Description
CF 511 is the first gun foam
introduced on the market that has
the ability of performing at and
below freezing. The CF 511
formula is designed to be used for
sealing and insulating residential
and commercial structures against
air, dirt, sound and pest infiltration.
Like CF 128-DW, CF 511 is a
CFC-free, one-component
polyurethane filler foam that
contains no urea formaldehyde and
is suitable for indoor use.
CF 511 Filler Foam and the CF-DS1
Dispenser together are a system
designed to provide precise
metering of product, stop-and-go
capability, and long service life for
the professional user.
Product Features/Benefits
Low temperature performance
allows the CF 511 to be applied
in cold weather conditions
Enhanced performance
characteristics allow foam to cure
at freezing without bubbling or
becoming brittle
Improved propellant provides
sufficient pressure to empty can
completely at or below freezing
without waste
Improved low temperature usage
formula can be used on
applications where CF 128-DW
is not suitable
Adhere drywall to stud framing
Can substitute up to 3238 tubes
of construction adhesive
Product Attributes:
Meets Class A fire rated
building specs
Contains HFC propellant
Physiologically harmless
when fully cured
Neutral odor for indoor use
Does not rot or deteriorate with
age if protected from UV
exposure
Adhering
Adhering drywall to stud framing
ASTM D 6464-99
Item No.
Description
00339427
CF 511 Filler Foam : 24 oz can
00339428
CF 511 Filler Foam : 1 case of 12 cans
00339429
CF 511 Filler Foam : 9 cases
00339430
00339431
Foam Combo Items
Item No.
Description
00339433
CF 511 Filler Foam :
Kit Complete
Includes 3 cans of CF 511 Foam, 1 CF-DS1 Dispenser,

1 CF-R1 Cleaner and Hilti Case
00339434
00339435
00339436
00339437
00339438
00339439
00339440
Dispenser
www.us.hilti.com
10.7
CF 511 Filler Foam : 3 cases with dispenser

CF 511 Filler Foam : 6 cases with dispenser
CF 511 Filler Foam : 9 cases with 2 dispensers
CF 511 Filler Foam : 64 cases with 4 long dispensers
Item No.
Description
00259768
00313187
00311512
Accessories
CF-DS1 Dispenser
P20-600K Extra Long Dispenser (with 27" barrel)
CF & EX/DS Plastic Nozzel Tip
Item No.
Description
00024631
CF-R1 Cleaner: 17 oz (500 ml) can
00311111
Foam Kit Box Empty
Foams
CF 116 Stop-N-Seal Grip Filler Foam
Technical Data
Reusable Filling Foam System
Product Description
Stop-N-Seal CF 116 is a reusable,
polyurethane filler foam system
which is perfect for stop and go
applications.
The Stop-N-Seal CF 116 system is
packaged in a kitbox making it easy
to carry and store. The CF 116
filling foam system is ideal for use
by plumbers, electricians, HVAC
contractors, and general
contractors.
Main Applications
Plumbing
Seal around plumbing pipes
Reduce pipe rattling and
vibration
Fill around drainage systems
Insulate around hot water lines
Electrical
Seal around electrical wiring and
conduit
Seal electrical boxes, outlets,
and light switches
Fill in and around cable trays to
reduce air movement

Heating & Air Conditioning
Seal return air vents
Seal HVAC duct penetrations
Seal around leaky vent pipes
Fill around A/C inlets
General Construction
Seal concrete formwork
Seal metal decking seams
Reduce drafts and energy loss
Fill pest penetrations
Bond foam panels and blocks
Product Features & Benefits

Reusable system allows user to
dispense contents of can after
several hours, days or even
weeks.
High yield provides over 50%
more foam per can than most
competitive foams
Unique grip dispenser allows
comfort and increased control of
application over traditional straw
foams
Cardboard kitbox is resistant to

weather and abuse while housing
the kit contents
Stops drafts which reduces
heating/cooling expenses.
Reduces noise and vibration to
provide a quieter living
environment
Yield of one can is equivalent in
volume to 46 10-oz tubes of
caulk
Foam can contents

12 fluid oz (340 g)

manufacture
9 months
Foam yield per can

0.5 ft3 (864 in3)
Linear feet yield at 1/2" bead

367 ft

Tack free: 1012 min
Ready to cut: 30 min
Fully cured: 23 hrs
Application temperature range

41F to 95F (5C to 35C)

UL 723
ASTM E 90
CF 116 is not to be used as a firestop
backer

approved
Flame Spread 15 Smoke Developed 45
5 in. on center covering 12.5 percent
of the exposed test sample area.
CF 116 System Components

Item No.
Description
00336320
Stop-N-Seal CF 116 Kit

CF 116 Refill Pack: (3)12 oz cans, (1) CF-GR Grip Dispenser
and (3) CF-GA Nozzles supplied in cardboard kit
00336321
CF 116 Refill Pack +
00259764
00024631
00259766
Bulk Items
CF-GR Grip Dispenser

CF-R1 Cleaner (not shown)
CF-FA1 Foam Finger Adaptor Nozzle (pack of 12)
(3)12 oz cans CF 116 Filler Foam and (3)CF-GA Nozzles
Item No.
Description
00311983
00259765
CF 116 Foam (case of 12 cans) & 12 Straws

CF-GA Straw Nozzles (pack of 12)
NEW!
www.us.hilti.com
10.8
Technical Data
Material
Synthetic Elastomeric Polymer
CA 3200 General Purpose Construction Adhesive

Bonds Wide Variety Of Materials, Including Foam Insulation
Consistency
Medium-Viscosity Mastic
Typical Applications
Color
CA 3200 bonds to most common

building materials including: wood,
metal, plaster, concrete, drywall,
acoustical panels, paneling,
tileboard, trim, corkboard and
polyurethane foam.
Tan
Application Temperature
Adhesive: 10F to 100F
Substrate: 10F to 100F
Service Temperature
0F to 150F
Flashpoint
Less than 0F
Freeze-Thaw Stability
Will not freeze
Open Time
20 minutes
Block Strength
232 psi
Shelf Life when stored at

temperatures between 40F to
90F
2 years from date of manufacture
Features/Benefits
Bonds polyurethane foam

Strong initial tack
Automatic shimming
Stays resilient
Will not freeze

Freeze/thaw stable
Water resistant
ASTM-C557
CA 3200 IS NOT
RECOMMENDED FOR
SUBFLOOR
APPLICATIONS.
Estimating Formula*
Lineal Feet : 29 oz Tube
Bead Size
Coverage
1/4"
88 lineal feet
3/8"
39 lineal feet
No. of Units Required =
(B2 * (L * 12))/66
B = bead size in inches
L = length in feet
*Numbers are approximate and assume
no waste.
NOT FOR SALE IN CALIFORNIA
1. Place adhesive cartridge into standard one quart dispenser, then cut the tip of the
cartridge nozzle at a slant to the desired bead diameter.
2. Puncture inner seal with nail or wire and apply adhesive in a continuous bead to
furring strips or studs and top and bottom plates. Material to be adhered should be
partially nailed or braced to aid alignment during installation. For laminating, use a
zig zag pattern.
3. When used for installing paneling, all panels should be measured and prefit, and
cutouts for switches and outlets completed before applying adhesive.
4. To speed bond development, materials should be pressed into position, then
removed for one minute and repressed. Apply only as much CA 3200 as can be
covered in 15 minutes. For best results, store at room temperature and use entire
contents of tube once it has been opened.
Surface Preparation
All surfaces should be clean, dry and free from all contaminants such as oil and
grease.
For Bonding Foam Products Foam Installations:
1. If adhering directly to wall, grind off excessive mortar and other high areas from
wall surface.
2. For urethane foam, apply a maximum 3/8" bead.
3. Press foam panel firmly against adhesive to make transfer, then partially pull out
panel for two to three minutes to release solvents and improve the grab of the
adhesive.
4. Gap should not exceed 1/16" after repressing panel in place.
5. When bonding polystyrene foam, surface temperatures should not exceed 90F.
Excessive adhesive thickness may cause significant etching of foamboard.
Cleaning
Tools and excess adhesive should be cleaned with mineral spirits.
Item No.
Description
00024808
00024809
00024933
CA 3200 Tube: 29 oz
CA 3200 Case of 12 tubes
CA 3200 Pallet of 240 tubes
Accessories
Item No.
Description
00024824
Adhesive Dispenser for 29 oz tube
www.us.hilti.com
10.9
CA 3400 Heavy Duty Subfloor Adhesive

Increases Structural Strength
Technical Data
Material
Consistency
Color
CA 3400 bonds securely to wood,

plywood, fiberboard, hardboard,
concrete, masonry, stone, tile,
marble, acoustical material and
most other common building
materials.
Light Tan
Application Temperature:
Adhesive: 0F to 100F
Substrate: 0F to 100F
Service Temperature
0F to 150F
Flashpoint
Less than 0F
Will not freeze
Open Time
20 minutes
Block Strength
Features/Benefits
Reduces nailing, helps prevent
squeaky floors
High strength bond
Will not become brittle or hard
Suitable for hot and cold gunning
Will not freeze
Water resistant
Remains resilient
1035 psi

90F
APA AFG-01
ASTM-C557
ASTM-D3498
FHA-UM60
Surface Preparation
1. All surfaces should be clean and free from all contaminants such as oil and grease.
2. Joist covered with ice, water, saw dust, snow, mud or other foreign materials should
be cleaned prior to application.
Installation
1. Place adhesive cartridge into standard one quart dispenser, then cut the tip of cartridge nozzle at a slant to desired bead diameter.
2. Puncture inner seal with nail or wire and apply adhesive in a continuous bead.
3. Press surfaces firmly together.
4. Apply only as much CA 3400 Subfloor Adhesive as can be covered within 20 minutes, and use a 1/4" zig zag bead when laminating underlayment to joists.
5. When installing CA 3400 for glued APA floor systems, apply per the American
Plywood Association specifications.
Cleaning
Tools and excess adhesive should be cleaned with mineral spirits.
Item No.
Description
00024806
00024807
00024932
CA 3400 Tube, 29 oz
CA 3400 Case of 12, 29 oz tubes
CA 3400 Pallet of 240, 29 oz tubes
DO NOT USE CA 3400

ON POLYSTYRENE
FOAM PRODUCTS.
Estimating Formulas*
Lineal Feet : 29 oz Tube
Bead Size
Coverage
1/4"
88 lineal feet
3/8"
39 lineal feet
(B2 * (L * 12))/66
L = length in feet
no waste.
NOT FOR SALE IN CALIFORNIA
Accessories
Item No.
Description
00024824
Adhesive Dispenser for 29 oz tube
www.us.hilti.com
10.10
Technical Data
Material
CA 3600 Water Based Construction Adhesive

High Performance, Superior Bond Strength
Consistency
Color
Beige
Application Temperature:
30F to 100F
Service Temperature
10F to 120F
Flashpoint
N/A
Passes 3 Cycles
Open Time
20 minutes
Block Strength
523 psi
Features/Benefits
Installation Data

90F:
Lowest VOC content available

Versatile: bonds most
construction materials
Superior bonding strength
Non-toxic, non-flammable
Solvent-free
Weather resistant; freeze/thaw
stable
specifications for subfloor
applications
Basic Use

APA AFG-01
ASTM-C557
ASTM-D3498
FHA-UM60
CA 3600 IS NOT
RECOMMENDED FOR
MATERIALS NOT LISTED,
SPECIFICALLY
INCLUDING VINYL.
Estimating Formula*
Lineal Feet : 10.5 oz Tube
Bead Size
Coverage
1/4"
32 lineal feet
3/8"
14 lineal feet
(B2 * (L * 12))/24
CA 3600 provides multi-purpose

versatility, far exceeding the
adhesive requirements of the
American Plywood Associations
AFG-01 Specification for Subfloor
Applications. CA 3600 provides
excellent bonding for a myriad of
construction applications including:
subfloors, furring strips, paneling,
drywall and cultured marble. CA
3600 is easily applied and cleans
off with water when uncured.
CA 3600 far exceeds APA AFG-01

Specifications for Subfloor
Applications and also provides
superior adhesion for most common
building materials including:
Wood
Slateboard
Wet, Frozen or Treated
Most other porous substrates
Lumber
Polyurethane
Waferboard
Gypsum Wallboard
Cultured Marble
Paneling
Masonry
Concrete
Ceramic or Acoustical Tile
Corian
Surface Preparation
All surfaces should be clean and free from all contaminants such as oil and grease.
Installation
1. Place adhesive cartridge in dispenser and cut tip at slant to desired bead diameter.
2. Puncture inner seal with nail or wire and apply adhesive in a continuous bead.
3. Press the surfaces firmly together. Large applications may require bracing until
adhesive has set.
4. When using on glued floor systems, follow APA guidelines for applying adhesive.
Note: Store adhesive at room temperature for 24 hours prior to use to allow proper
extrusion when application involves temperatures below 400F.
Cleaning
Tools and excess adhesive may be cleaned with water while adhesive is in an
uncured state. Dried adhesive can be removed with scraper.
L = length in feet
CA 3600 is packaged in two convenient sizes: standard 10.5
fl oz tubes and larger, more economical 29 fl oz tubes.
Lineal Feet : 29.0 oz Tube

Bead Size
Coverage
1/4"
88 lineal feet
3/8"
39 lineal feet
(B2 * (L * 12))/66
L = length in feet
no waste.
10.5 fl oz
Item No.
Description
00020128
00020129
00020130
29 fl oz
CA 3600 Tube 10.5 fl oz

CA 3600 Case of 24 Tubes
Item No.
Description
00020125
00020126
00020127
CA 3600 Tube 29 fl oz
CA 3600 Case of 12 tubes
Accessories
www.us.hilti.com
10.11
Item No.
Description
00024825
00024824
Dispenser for 10.5 oz tube

Dispenser for 29 oz tube
Concrete Crack Repair System
CI 060 EP/CI 070 EP Crack Injection System

Concrete Crack Repair System: Simple, Cost Effective and Provides Significant Savings
Technical Data
Injection Resin CI 060 EP
Shelf life from date of manufacture
when stored at 50 to 80F
Resin and hardener: 2 years
Concrete columns, beams, floor

slabs, walls
Basement walls
Swimming pools
Cracks in large concrete
structures, such as parking
garages, grain silos, bridges,
containment walls
Rec. application temp. Range

50 to 113F
Working Time
90 minutes at 50F
40 minutes at 73F
15 minutes at 90F
MInimum curing time at 68F

Approx. 24 hrs
Compressive Strength
12,000 psi
Tensile Strength
7,120 psi
Features & Benefits

100% solids epoxy
New, self contained cartridge with resin and hardener
in a single package
Non-return valves in ports and injection hoses help
eliminate spills
No expensive equipment required

No drilling required to install ports
Effectively seals cracks in concrete structures
Excellent resistance to many chemicals
Meets requirements of ASTM C-881, Type II, Grade 1,
Class B
Compressive Modulus
265,000 psi
Contents
1 tube CI 060 EP resin and
hardener=14.3 in.3
Technical Data
Surface Sealing Compounds
Shelf life from date of manufacture
when stored at 59 to 77F
Resin and hardener: 1 year
Rec. application temp. Range

40 to 90F
Working Time
Application Instructions
1. Clean surface along the crack. Blow out crack with dry and
oil-free compressed air.
2. Bond injection ports with CI 070 EP Crack Sealing
Compound. Port spacing approximately 6" to 12" with wider
spacing for thinner slabs.
3. Seal the crack with CI 070 EP crack sealing compound in
strips of minimum 2" wide, 1/8" deep.
4. A light tap with a hammer to the rear end of the CI 060 EP
cartridge breaks the glass cylinder, releasing the hardener.
Mix by see-saw motion for approximately 30 motions do
not shake.
5. Puncture the seal of the cartridge tip. Then screw on
connection hose.
6. Plug connection hose to bottom port. Place air relief stopper

in next port above.
7. Inject CI 060 EP resin until it appears visibly in the next port
above. Remove air relief stopper (non-return valve is now
closed) and insert into next port. Continue injecting into
original port until the port accepts no more resin (when
normal hand pressure is used on the dispenser).
8. Detach connection hose from port and plug to the next
higher port. Repeat operating steps 6 and 7 up to the end
of the crack.
9. After the injection resin has set generally over night
the ports and the sealing compound can be removed with a
flat chisel. If required, the surface can be ground even.
0.0100 0.0200
0.06
0.12
0.24
0.36
0.48
0.60
0.72
0.96
1.08
1.44
2.16
0.12
0.24
0.48
0.72
0.96
1.20
1.44
1.92
2.16
2.88
4.32
0.24
0.48
0.96
1.44
1.92
2.40
2.88
3.84
4.32
5.76
8.64
Crack Width (in.)

0.0312 0.0400 0.0550 0.0625
(1/32")
(1/16")
0.37
0.48
0.66
0.75
0.75
0.96
1.32
1.50
1.50
1.92
2.64
3.00
2.25
2.88
3.96
4.50
3.00
3.84
5.28
6.00
3.74
4.80
6.60
7.50
4.49
5.76
7.92
9.00
5.99
7.68 10.56
12.00
6.74
8.64 11.88
13.50
8.99
11.52 15.84
18.00
13.48
17.28 23.76
27.00
0.0700
0.84
1.68
3.36
5.04
6.72
8.40
10.08
13.44
15.12
20.16
30.24
0.1250
(1/8")
1.50
3.00
6.00
9.00
12.00
15.00
18.00
24.00
27.00
36.00
54.00
0.1450
1.74
3.48
6.96
10.44
13.92
17.40
20.88
27.84
31.32
41.76
62.64
0.1770
2.12
4.25
8.50
12.74
16.99
21.24
25.49
33.98
38.23
50.98
76.46
0.1870
(3/16")
2.24
4.49
8.98
13.46
17.95
22.44
26.93
35.90
40.39
53.86
80.78
0.2050
2.46
4.92
9.84
14.76
19.68
24.60
29.52
39.36
44.28
59.04
88.56
Item No.
Description
00220244
CI 060 EP Kit
Includes: 172 in3 injection epoxy, 30 ports with non-return
valves, 6 connection hoses with non-return valves,
4 air relief stoppers
00225491
00225493
00020132
00020133
00020134
00055205
CI 070EP: Min. 3 hrs at 70F
Quick Set Epoxy

Approx. 30 mins at 73F
CI 070EP: 11,000 psi
Tensile Strength
CI 070EP: 6,900 psi
Compressive Modulus
Contents
CI 060 EP Crack Injection System Volume of Resin per Linear Foot of Crack (in )
0.0050
Approx. cure schedule
CI 070EP: 293,000 psi

3
Depth of
Crack (in)
1"
2"
4"
6"
8"
10"
12"
16"
18"
24"
36"
CI 070EP: 34 mins at 40F

10 mins at 77F
Quick Set Epoxy: 6 mins at 40F
34 mins at 77F
CI 070 Crack Sealing Compound (1 quart)

CI 070 EP Crack Sealing Compound, Case of 4 quarts
Bag of 30 ports with non-return valves
Bag of 6 connection hoses with non-return valves
Bag of 4 air relief stoppers
CB 200 PI dispenser
CI 070: 1 quart resin and hardener

(covers approx. 5070 ft)
Quick Set Epoxy: 9 fl oz tube
(covers approx. 5070 ft)
Read product labeling

and accompanying
literature before using.
Estimating Formula*
Vol. of resin per lineal feet of crack (in3)
To estimate how many kits (12 tubes per
kit) of CI 060 EP are required to fill a
crack:
No. of Kits Required = (V * L) / 172
(round up to next whole number)
V = Volume per linear foot from above chart
in cubic inches
L = Length of crack in feet
*Numbers are approximate and assume no
waste.
www.us.hilti.com
10.12
Concrete Crack Repair System
RM 700 EP/ RM 710 EP Epoxy Based Repair Mortars
Technical Data
Solids Content
Long Lasting, Economical, Easy to Use, and USDA Approved
100%
Color
light gray
Shelf Life
The tenacious adhesion, chemical

resistance and excellent weatherability makes RM 700 EP Repair
mortar suitable for a wide variety of
repair projects including:
Repairs to floor slabs, ramps,
expansion joint edges
Replacement of chemically
attacked concrete
Application Temp. Range

RM 700 EP: 40 to 80 F
RM 710 EP: Base matl: 25 to 80F;
Mortar: 50 to 90F
Pot Life
RM 700 EP: At 70F: 3045 mins
(150 gm. mass)
RM 710 EP: At 40 F: 3040 mins
Other applications for

RM 700 EP include:
Initial Cure
RM 700 EP: 24 hrs to full traffic at
70F
RM 710 EP: Approx. 24 hrs to full
traffic at 30F; 34 hrs to
full traffic at 70F
Full Cure
RM 700 EP: 27 days at 70F
RM 710 EP: 37 days at 30F
Compressive Strength (psi)

(ASTM D695, 1/2"x1/2"x1" bars)
RM 700 EP: 10,849 at 10%

deformation or less
RM 710 EP: 7,560 at 10%
deformation or less
Tensile Strength (psi) (ASTM D638)

RM 700 EP: 8,157
RM 710 EP: 6,030
Features & Benefits

Durable, Long lasting
High strength mortars resist
weather, abrasion
Virtually unaffected by freeze/thaw
cycles
Withstands significant physical
abuse
Easy to Use
All resin/hardener and aggregate
premeasured
Mortar is easily troweled into place
Cures rapidly
100% Solids Epoxy

Bonds to both concrete and steel
Excellent water and chemical
resistance
No shrinkage, no solvent fumes
Primerless
Richer blend eliminates the need
for primer
Coverage
One 65 lb. pail covers approximately
25 ft2 at 1/4" thickness
One 9 lb. pail covers approximately
3.5 ft2 at 1/4" thickness
Read product labeling and

accompanying literature before using.
RM 700 EP: 0.44 ft-lb /in. notch

RM 710 EP: N/A
For faster Cure, Application

at lower Temperatures:
For interior applications where a
faster cure or application at lower
temperatures is required, use
RM 710 EP.
Impact Strength (IZOD)

(ASTM D256, 1/2" x 1/2" x 2-1/2" bars)
Concrete exposed to extreme

weather conditions such as
freeze/thaw cycles, constant
moisture
Concrete in high traffic areas
such as warehouse floors,
loading docks, driveways, etc.
Concrete subject to chloride
(salt) or sulphate attack
Areas where water based latextype patching compounds have
failed
Impact Resistance
Excellent
Heat Deflection Temperature

(ASTM D648, 1/2"x1/2" bars, span = 4")
RM 700 EP: 156F

RM 710 EP: 113F
Chemical Resistance
RM 700 EP
RM 710 EP
Acids*
Excellent
Bases*
Excellent
Salt Water
Excellent
Animal Fats Excellent
Hot Water
Excellent
Solvents
Very Good
*pH between 3 and 10
Excellent
Excellent
Excellent
Very Good
Excellent
Very Good
Estimating Formula*
Number of Units Required =
(L * W * (Dave / 12)) / Yprod
L = length of void in feet
W = width of void in feet
Dave = ave. depth of void in inches
Yprod = Yield for product
(see table below)
Estimated Yield for Repair Mortars
& Grout (Yprod) in ft3
Product
RM 700 EP (65 lb. unit)
Yprod
0.521
0.073
0.521
0.073
*Numbers are approximate and assume no waste.
10.13
Application Instructions
1. Score concrete around damaged area to a minimum of 1/4" using a Hilti dry diamond blade.
2. Expose fresh concrete surface and chip out edges to a depth of 1/4" using a Hilti
Combihammer (such as TE 55) and chisel or bushing head. Remove dust and
debris from surface using vacuum or compressed air.
3. Open RM 700EP/RM 710EP container. Pour sand into box and empty contents of
both liquid components into the mixing pail provided. Allow liquid to drain completely into the mixing pail. Place empty Part B container upside down into Part A
container.
4. Using a Hilti drill that accepts smooth shank 1/2" bits (HIlti SR 16 suggested) with
Hilti mixing paddle (item no. 00024155) , mix parts A and B until thoroughly blended. Pour sand back into liquid portions and continue to mix until mortar has
achieved a uniform consistency, free of lumps of dry sand.
5. Place mortar on damaged area. Using a trowel, push mortar into all corners and
exposed edges.
6. Finish patch with trowel. Protect from traffic until cured.
Item No.
Description
00020264
00020428
00020268
00020429
00024155
RM 700 EP Fast-Set Pail

65 lb pail
RM 700 EP
9 lb unit
RM 710 EP Fast-Set Pail
65 lb pail
RM 710 EP
9 lb unit
Stainless Steel Paddle Mixer smooth shank (shown below)
Size
Specially designed for epoxy mortar. Use with Jacobs style chuck.
www.us.hilti.com
Concrete Repair System
RM 800 PC Portland Cement Based Repair Mortar

Durable, Fast Setting and Exceeds ASTM Standards
Technical Data
Working time
1520 mins
Set Time (ASTM Test C-266)
The fast cure, primerless adhesion

durability of RM 800 PC make is
suitable wherever pedestrian and
vehicular traffic are anticipated.
Roadways
Runways and taxiways
Bridges
Parking structures
Warehouse floors
Loading docks
Setting posts, railings and
parking meters
Fast Setting
Initial (Hrs:Min): 0:35

Final (Hrs:Min): 0:45
Flexural Strength
(ASTM Test C-580) 28 Days
800 psi
(ATSTM Test Method C-109)
3 hrs
1 day
28 days
C-928 Req
RM800PC
500 psi
2000 psi
4000 psi
2500 psi
4500 psi
6500 psi
Percentage Length Change

(ASTM Test Method C-157)
C-928 Req
RM800PC
Air-cured
0.20 max 0.06 max
Moist-cured +0.20 max +0.06 max
Resistance to deicing salts

Takes vehicular traffic after 3 hours at 70F

Minimizes downtime and revenue loss
(10% Calcium Chloride, 25 cycles)
Self Bonding
Water Absorption
Requires no bonding agents or primers

Shorter application process
Pre-Blended
Just add water
Mix with Hilti drill and paddle or mortar mixer
Coverage
One 50 lb pail yields 0.42 ft3 and covers approximately 10 ft2 when
applied 1/2" thick
C-928 Req
RM800PC
2.5 rating max 2.0
9.8%
Freeze-Thaw Resistance
(ASTM Test Method C-666,
procedure A) 3000 cycles
88% Dynamic modulus
Flow (15 min)

C-928 Req
RM800PC
100%
100%
Estimating Formula*
1. Score concrete around damaged area at a slight backward angle to a minimum
depth of 1/2" using Hilti Dry Diamond Blade.
2. Expose fresh concrete surface and chip out edges to a depth of 1/2" using a Hilti
Combihammer (TE 55 suggested) and chisel or bushing head .
Remove dust and debris with vacuum or compressed air.
3 Saturate prepared area with water. Add 2 quarts of potable water to an empty 5 gal
pail. Slowly add powdered RM 800PC and mix using Hilti SR 16 drill
(or equivalent) and stainless steel paddle mixer (sold on previous page) until free of
lumps. Add an additional quart of water, alternating with remaining
powder, until entire contents have been thoroughly blended.
4. After removing excess water from prepared area, Using a trowel, place mortar and
push into all corners and edges.
5. Finish patch with trowel. Protect from traffic until cured.

(L * W * (Dave / 12)) / Yprod
(see table below)
Estimated Yield for Repair

Mortars & Grout (Yprod) in ft3
Product
Yprod
RM 800 PC
0.420

waste.
Item No.
Description Size
00020270
RM 800 PC 50 lb pail
00024155
Stainless Steel Paddle Mixer smooth shank

Specially designed for epoxy mortar.
Use with Jacobs style chuck.
www.us.hilti.com
10.14
Cementitious Grout
Technical Data
Color
CG 200 PC Cementitious Grout

For Heavy Equipment, Steel Columns, Bearing Plates
concrete gray
Water content by weight

Plastic
Fluid
17.7%
23.0%
Compressive Strength (psi)

ASTM C-943 confined
1 day
3 days
7 days
28 days
Plastic
Fluid
3,000 psi
8,000 psi
10,000 psi
11,000 psi
2,500 psi
5,000 psi
7,000 psi
8,500 psi
CG 200 PC is suitable for use in

the grouting of heavy equipment
and machinery, concrete and
structural steel columns, anchors
and bearing plates, as well as
grouting and leveling precast and
prestressed members.
Working Time
Plastic
Fluid
1520 min 1520 min
Set Time (hrs:min) ASTM C-191

Initial:
Final
Plastic
Fluid
2:45
5:15
5:15
7:45
Consistency (seconds)
Plastic
Flow,
ASTM C-230
Cone,
ASTM C-939
Fluid
112
N/A
N/A
21
Volume Change (% expansion)
Limitations
CG 200 PC is a non-metallic, noncorrosive and no-shrink portland

cement grout. CG 200 PC is
designed for applications where high
fluid mixes or compressive strengths
in excess of 10,000 psi are desired.
CG 200 PC is not for use in

areas subject to spillage of acids
or sulfates.
CG 200 PC must not be vibrated
during placement. Consolidation
is to be by rodding.
CG 200 PC must be coated with
a protective membrane when
exposed to acids or sulfates.
ASTM C-827
Plastic
At time of set: +0.21%

24 hrs:
+0.13%
Fluid
+0.30%
+0.33%
Volume Change (% expansion)

CRD-C-621
3 days
7 days
14 days
28 days
Plastic
Fluid
+0.04%
+0.05%
+0.03%
+0.03%
+0.08%
+0.07%
+0.07%
+0.05%
Applicable standards
ASTM C-1107
Corps of Engineers Specification
CRD-C-621 Type A and C
Estimating Formula*
(L * W * (Dave / 12)) / Yprod
(see table below)
Estimated Yield for Repair

Mortars & Grout (Yprod) in ft3
Product
Yprod
CG 200 PC (Plastic Consistency) 0.510
CG 200 PC (Fluid Consistency) 0.550
waste.
Installation instructions
Temperatures
During mixing and placing maintain a temperature of 60F for grout and water. Air
and substrate temperatures must be above 45F during placement, and must remain
above freezing for 48 hours afterwards.
Surface Preparation
Saturate the substrate with water for 24 hours prior to grout placement. The area to
be grouted must be free of loose or deteriorated concrete, dust, dirt, grease, oil and
paints or other coatings. If grouting beneath structural systems, provide air relief
holes as necessary. Remove excess water with absorbent cloths, compressed air or
vacuuming, leaving no puddles.
Mixing
CG 200 PC may be mixed to a dry pack, hand trowel or fluid pourable consistency,
depending on the amount of water added. Do not add additional cement or other
materials for any reason.
The water additions shown below will provide a general guideline for achieving the
desired consistency. Amounts shown are for 55 pounds (one unit) of powdered
product. The actual amount of water required may be affected by the temperature,
batch size and mix method chosen.
DO NOT add excessive water which may cause bleeding or segregation of
aggregates under job conditions.
DO NOT use vibrators in placing the grout
Desired Consistency
Plastic (Trowel Consistency)
Fluid (PumpingConsistency)
Grout
Water
Yield
Unit Weight
55 lb
1.1 gal (9.1 lb)
0.51 ft3
126 lb/ft3
55 lb
1.5 gal (12.3 lb)
0.55 ft3
122 lb/ft3
CG 200 PC is packaged in resealable pails containing 55 lb of product
Item No.
Description
00020271
CG 200 PC Cementitious Grout - 55 lb Pail
www.us.hilti.com
10.15
Sealers
CS 300 EP Pavement Joint Sealant
Technical Data
Color
concrete gray
Type
CS 300 EP is designed for sawcut
or cast joints in floors and
pavement. It is recommended for
use on highways, bridges, airports,
garages, industrial floors and
marine decks.
Epoxy-urethane hybrid
Solids by weight
100%
Working time
30 minutes at 70F
Approx. Cure Schedule at 75F*

Tack Free:68 hrs
Time to Traffic: 24 hrs
Full Cure:35 days
Mix Ratio
1:1 by volume
Application Temperature
50F minimum
Service Temperature
40 to 200F

CS 300 EP is a two-component,
polymer hybrid containing both
urethane and epoxy resins in order to
provide a resilient filler for control
joints in pavement and floors. This
unique chemistry allows excellent
flexural strength and elongation while
maintaining high tensile strength. The
epoxy/urethane blend exhibits
excellent adhesion, which results in a
long-lasting, durable repair.
CS 300 EP contains 100% solids.
There are no solvents to cause
shrinkage or odor. This product also
complies with VOC (Volatile
Organic Content) regulations in New
York, New Jersey and California.
CS 300 EP is a flexible yet tough
sealant. It can accommodate minor
slab movements, yet withstand the
abuse of forklift traffic and other

types of heavy rolling loads. CS 300
EP also resists damage from point
loads such as high heel shoes.
Tensile Strength
3,289 psi
Elongation to Break
50.4% at 70F
Flexural Strength
Coverage
2,782 psi
2 gallons at 1/2" x 1" yields

approximately 6070 lineal feet
Shore A Hardness
Limitations
Shore D Hardness
CS 300 EP is not designed for

expansion joint applications.
CS 300 EP is a self-leveling
sealant, which is not appropriate
for vertical wall or steep slope
applications.
Substrate and sealant
temperature must be above 50F
during installation and for 24
hours afterward
CS 300 EP is a 2-component
sealant requiring thorough mixing
prior to use.
56
84
Abrasion Resistance
Taber abrasion, CS10 wheel, 1000
cycles, 1000 gm load, 25.4 mg weight
loss
ASTM C-881
The above data represent the results of
actual testing.
*Tested at 75F at 55%RH.
Surface Preparation
The joint edges must be clean, dry and free of loose mortar, dust and laitance.
Waterproofing or dampproofing coatings, curing agents and form release compounds
must be completely removed. Sandblasting or grinding are the preferred methods.
Mixing
Mix Part A and Part B thoroughly prior to use. Using a Hilti TE-25 drill and a Hilti
mixing paddle, mix for 5 minutes minimum, stopping after 2 to 3 minutes to scrape
the sides of the mixing container and the paddle and to incorporate any remaining
unblended material.
If, at the end of the mixing period, there are streaks present in the material, scrape
the can and mix for an additional 2 minutes. Repeat as necessary until material is
streak-free.
Joint backing
In moving joints, a non-absorbent joint backing must be inserted under compression
in order to control joint depth. Construction joints, crack control joints, or cold joints,
in which no movement is expected may be filled completely, or to a depth of 1-1/2",
whichever is less.
Application
Allow 24 hours prior to opening area to traffic.
CS 300 EP is packaged in a 2 gallon kit containing equal volumes of Part A
and Part B
Item No.
Description
00020295
CS 300 EP Pavement Joint Sealant 2 gal Kit
www.us.hilti.com
10.16
Sealers
Technical Data
Solids content
CC 400 EP Epoxy-Polyamide Sealer

For Protecting Concrete Surfaces
45-50%
Color
Clear, pale amber
Coverage
250350 ft2 per gal
CC 400 EP is a USDA approved,

two-component water based
epoxy-polyamide sealer used to
protect concrete surfaces from
dusting and enhance the
cleanability of floors.
Because CC 400 EP is water
based, there is not strong solvent
odor. CC 400 EP is V.O.C.
compliant in New York, New Jersey
and California.
Recommended Thickness
3 mils dry
Weight Per Kit

Part A: 6.55 lb
Part B: 1.90 lb
Mix Ratio
4:1 by volume
Shelf Life
12 months from date of manufacture
VOC Content
Part A: 1.26 lb/gal
Part B: 0.0 lb/gal
Mixed: 1.0 lb/gal
Abrasion Results
V.O.C. in New York, New Jersey and California
56 mg loss, Taber Abrasor CS-17

Calibrase Wheel 1000 gm load, 500
cycles
Impact Resistance
Gardiner Variable Impactor, 50 in.-lb,
direct passed
Flexibility
No cracks on 1/8" mandrel

Tack free: 4 hrs
Recoat: 57 hrs
Light Traffic: 816 hrs
Full Cure: 27 days
CC 400 EP should not be used in place of an elastomeric waterproofing

membrane (Waterproofing membranes are designed to bridge small
moving cracks)
CC 400 EP must not be permitted to freeze prior to application
Do not place CC 400 EP when slab temperatures are below 50F or above
90F, or when relative humidity is above 70%
Material should be placed within 1 hour after mixing resin and hardener
Surface Preparations
Pot Life
4590 mins at 75F
Chemical Resistance
Immersion Splash
Weak Acids:
Strong Acids:
Bases (Alkali):
Petroleum Solvents:
Hydraulic Fluid:
Gasoline:
Ethylene Glycol:
Battery(Sulfuric) Acid:
Limitations
G
NR
VG
NR
G
G
EX
G
G
NR
EX
NR
G
G
EX
G

G=Good, VG=Very Good, Excellent=EX,
NR=Not Recommended
Surfaces to be coated with CC 400 EP must be clean, and free of surface

contamination, such as dust, dirt and laitance. Surfaces may be damp, but there must
be no standing water.
Concrete surfaces may be prepared by high pressure water cleaning, wire brushing,
sand or shot blasting, or acid etching.
If acid etching is chosen, the surface must be thoroughly rinsed with clear water
afterward, to remove all traces of the acid.
Where previously applied coatings are present, in many cases they may remain in
place if desired. The coatings must be firmly bonded, and a test patch of CC 400 EP
must be applied to determine adhesion. Prior to application of CC 400 EP, the
coating must be wire brushed or scarified, then cleaned.
Mixing
Combine Part A and Part B and mix thoroughly, using a TE-25 and a Hilti mixing
paddle.
Application
CC 400 EP may be rolled, brushed, or sprayed onto surfaces. If rolling, choose a
roller with a 3/8" nap for best results.
CC 400 EP is packaged in 5 gallon and 0.5 gallon kits, consisting of
premeasured portions of resin and hardener in a water base.
Item No.
Description
00020272
CC 400 EP Clear Epoxy Sealer 5 gal Kit
www.us.hilti.com
10.17
Sealers
CC 410 EP Gray Epoxy-Polyamide Skidproofer

For Protecting Concrete Surfaces
Technical Data
Solids content
64% 3%
Color

CC 410 EP is USDA approved, two-component water based epoxypolyamide sealer with aggregate, used to protect concrete surfaces from
wear and to minimize the likelihood of slipping on wet floors.
Because CC 410 EP is water based, there is not strong solvent odor and is
VOC (Volatile Organic Content) compliant in New York, New Jersey and
California. Unlike many other water based coatings, CC 410 EP
performs as a durable, wear-resistant sealer.
Light gray
Coverage
125-150 ft2 per gal
Recommended Thickness
5-6 mils wet
Weight Per Kit

Part A: 20.5 lb
Part B: 4.25 lb
Silica Aggregate: 12.4 lb
Mix Ratio
4:1 by volume (liquids only)
Shelf Life
12 months from date of manufacture
VOC Content
Mixed: 0.79 lb/gal
Meets V.O.C. in New York, New Jersey and California
Limitations
Abrasion Results
56 mg loss, Taber Abrasor CS-17
Calibrase Wheel 100 gm load, 500
cycles
CC 410 EP should not be used in place of an elastomeric waterproofing

membrane (Waterproofing membranes are designed to bridge small
moving cracks).
CC 410 EP must not be permitted to freeze prior to application.
Do not place CC 410 EP when slab temperatures are below 50F or above
90F, or when relative humidity is above 70%.
Material should be placed within 1 hour after mixing resin and hardener.
Impact Resistance
Surface Preparations
Pot Life
Surfaces to be coated with CC 410 EP must be clean and free of surface

contamination, such as dust, dirt and laitance. Surfaces may be damp, but there must
be no standing water.
Concrete surfaces may be prepared by high pressure water cleaning, wire brushing,
sand or shot blasting, or acid etching.
If acid etching is chosen, the surface must be thoroughly rinsed with clear water
afterward, to remove all traces of the acid.
Where previously applied coatings are present, in many cases they may remain in
place if desired. The coatings must be firmly bonded, and a test patch of CC 410 EP
must be applied to determine adhesion. Prior to application of CC 410 EP, the coating
must be wire brushed or scarified, then cleaned.
Mixing
Gardiner Variable Impactor, 50 in.-lb,

direct passed
Flexibility
No cracks on 1/8" mandrel

Tack free: 46 hrs
Recoat: 68 hrs
Light Traffic: 816 hrs
Full Cure: 27 days
90 mins at 75F
Chemical Resistance
Immersion
Weak Acids:
Strong Acids:
Bases (Alkali):
Petroleum Solvents:
Hydraulic Fluid:
Ethylene Glycol:
G
NR
VG
NR
G
EX
Splash
G
G
EX
NR
G
EX

G=Good, VG=Very Good, Excellent=EX,
NR=Not Recommended
Combine Part A, Part B and aggregate and mix thoroughly, using a TE-25 and a Hilti
mixing paddle.
Application
CC 410 EP may be rolled, brushed, or sprayed onto surfaces. If rolling, choose a
roller with a 1/4" nap for best results.
CC 410 EP is packaged in 3.5 gallon kits, consisting of premeasured portions
of resin and hardener in a water base, with non-skid grit.
Item No.
Description
00020273
CC 410 EP Epoxy Non-Skid Floor Sealer 3.5 gal
www.us.hilti.com
10.18
MC 800/MC 850 So-Safe Biodegradable Graffiti Remover

Works on Variety of Surfaces
Features & Benefits
MC 800 Light Duty
Liquid
This liquid formulation is
designed to safely remove
spray paint, marker, pen,
glue, and grease from nonporous materials without
affecting most surfaces.
Suitable for graffiti removal
from painted surfaces such
as signs, as well as
stainless steel and most
plastic surfaces.
MC 850 Heavy Duty

Sprayable Gel
This gel formulation is
designed to safely remove
spray paint, marker, pen,
glue, and grease from
porous surfaces and for
difficult-to-remove graffiti
on non-porous surfaces.
Suitable for graffiti
removal from uncoated

concrete, hollow block and
masonry. Formulation will
not run or sag, allowing for
maximum contact time
with the graffiti.
Who can benefit

from So-Safe Graffiti
Remover?
Schools
Airports
Postal facilities
Utilities/Teleco
Transit systems
Neighborhood
D.O.T.s
Housing Authorities
groups
Parks departments
Where can So-Safe

Graffiti Removers be
used?
Restrooms
1 quart bottles,
12 quart cases
Mailboxes
Buses and trains
Street signs
Concrete/masonry
Bridges
Countertops
Machinery
Building panels
Printing presses
Bus shelters
Proven in the field.

So-Safe Graffiti Removers
have been evaluated for
effectiveness and safety by
a number of agencies and
organizations, including:
D.O.T.s
Marking film
manufacturers
Transit authorities
School Systems
Community
organizations
City and county
governments
Shelf Life / Storage

1 year from date of
production. Store in Hilti
package or polyethylene
container. Avoid storing
product in PVC.
Limitations
MC 800 and MC 850 may
dull the finish of certain
painted surfaces and
plastics. It is
recommended that the
product be tested in an
inconspicuous area before
general use. MC 800 and
MC 850 are neutralized
by water. When not in use,
keep containers tightly
sealed. Do not dilute
before use.
Item No.
Description
Item No.
Description
00254391
00254390
MC 800 QT
MC 800 CASE
00254388
00254389
MC 850 QT
MC 850 CASE
MC 200 Biodegradable Cleaner

MC 300 Biodegreaser
MC 200
MC 200 is a non-flammable,
biodegradable, all purpose cleaner
designed for use on plastic, metal
and other surfaces. MC 200
removes grease, oil scum, ink, wax,
dirt and soil from floors, printing
presses, lathes, milling machines,
machining equipment, shower stalls
and many other areas.
MC 200 is non-acidic, making it safe

for use on oxidizable metals. It
effectively replaces flammable
solvents and may be diluted at a rate
of 1 part MC 200 : 15 parts water.
MC 300
maintain grease traps.

MC 300 contains no petroleum
derivatives which can turn rancid.
This product is also safe for use in
parts washers as an additive or sole
degreaser. Water dilutible for general
cleaning and degreasing.
MC 300 also helps control odors on
surfaces and in sewage treatment
facilities.
MC 300 is a citrus-based,
biodegradable degreaser designed
to clean grease, grime and soap
scum, lift oil from concrete and help
MC 200 and MC 300 are also available in 5 gallon units MC 200 and MC 300 are also available in 5 gallon units
Item No.
Description : Size
Item No.
Description : Size
0020275
MC 200 Biodegradable Cleaner:

(1 gal units) Case of 4
0020276
0020277
MC 300 Biodegreaser: 1 gal

MC 300 Biodegreaser: (1-gal units)
Case of 4

MC 400 is a creamy, protective hand cleaner. This product may be used with or without water to remove grease,
grime, oil, tar, ink, paint, moly, asphalt, carbon, putty adhesives and other soils.
MC 400 is formulated for use by mechanics, oil field teams, construction and airport personnel among others. MC 400
contains a lanolin-based skin conditioner and leaves hands smelling fresh with no oily odor.
10.19
Item No.
Description
0020278
0020279

MC 400 Waterless Hand Cleaner (22 oz unit) Case of 12
Size
22 oz Tube
Product Notes
CORDLESS
DIRECT
FASTENING
DRILLING &
DEMOLITION
DIAMOND
CORING
& SAWING
FIRESTOPPING
SAWING &
GRINDING
SCREW
FASTENING
ADHESIVE &
MECHANICAL
ANCHORING
MEASURING
SYSTEMS
INSTALLATION
SYSTEMS
www.us.hilti.com
Product Notes
Call 1-800-879-8000
for program details.
* Limitations apply. Please contact Hilti for program details.
CORDLESS
DIRECT
FASTENING
DRILLING &
DEMOLITION
DIAMOND
CORING
& SAWING
FIRESTOPPING
SAWING &
GRINDING
SCREW
FASTENING
ADHESIVE &
MECHANICAL
ANCHORING
MEASURING
SYSTEMS
INSTALLATION
SYSTEMS
www.us.hilti.com
Product Notes
CORDLESS
DIRECT
FASTENING
DRILLING &
DEMOLITION
DIAMOND
CORING
& SAWING
FIRESTOPPING
SAWING &
GRINDING
SCREW
FASTENING
ADHESIVE &
MECHANICAL
ANCHORING
MEASURING
SYSTEMS
INSTALLATION
SYSTEMS
www.us.hilti.com
Terms & Conditions of Sale

PAYMENT TERMS:
Net 30 days from date of invoice. Customer agrees to pay all costs incurred by Hilti in collecting
delinquent amounts, if any, including reasonable attorneys fees.
FREIGHT:
All sales are F.O.B. Destination with transportation allowed via Hilti designated mode. Additional
charges may apply for expedited shipments, special handling requirements, and orders below
certain dollar amounts.
CREDIT:
RETURN POLICY:
WARRANTY:
All orders sold on credit are subject to Credit Department approval.

Products must be in saleable condition to qualify for return. Saleable condition is defined as those
unused items in original packaging and in unbroken quantities. All returns are subject to Hilti
inspection and acceptance, and a 15% restocking charge. Proof of purchase is required for all
returned materials. Special orders and discontinued items are not eligible for return credit. Dated
materials are not returnable 30 days beyond date of invoice.
Hilti warrants that for a period of 12 months from the date it sells a product it will, at its sole option
and discretion, refund the purchase price of, repair, or replace such product if it contains a defect in
material or workmanship. Absence of receipt of a written notification to Hilti of such a defect within
this 12-month period shall constitute a waiver of all claims with regard to such product. The
warranty time periods for certain products are limited by the warranty period in the literature that
accompanies these products.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANT-ABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Hilti shall in no event be liable for, and Customer hereby
agrees to indemnify Hilti against all claims related to, special, direct, indirect, consequential, or any
damages arising out of or related to the sale, use, or inability to use the product.
ACCEPTANCE OF
ORDER:
DOMESTIC ORIGIN:
BUSINESS SIZE:
PRICES:
CONSENT TO
JURISDICTION:
Acceptance is limited to the express terms contained herein, and terms are subject to change by Hilti
with reasonable notice to Customer. Additional or different terms proposed by Customer are deemed
material and are objected to and rejected, but such rejection shall not operate as a rejection of the
offer unless it contains variances in the terms of the description, quantity, price or delivery schedule
of the goods.
Any non-domestic Hilti product will be so identified on shipping documents and invoices for federal
government customers. All other customers may obtain such information by written request to Hilti,
Inc., Contract Compliance, P.O. Box 21148, Tulsa, Oklahoma 74121. Hilti sales personnel are not
authorized to warrant the country of origin of Hilti products.
Hilti is a large business.
Prices are those stated on the order. Hilti does not maintain most favored customer records, makes
no representation with respect to same, and rejects any price warranty terms proposed by
Customer. The Hilti published net price list is subject to change without notice.
All transactions made pursuant hereto shall be deemed to have been made and entered into in
Tulsa, Oklahoma. Any and all disputes arising directly or indirectly from such transactions shall be
resolved in the courts of the County of Tulsa, State of Oklahoma, to the exclusion of any other court,
and any resulting judgment may be enforced by any court having jurisdiction of such an action. All
transactions shall be governed by and construed in accordance with the laws of the State of
Oklahoma.
INDEMNIFICATION:
Customer hereby agrees to indemnify Hilti for any costs, including attorneys fees, incurred by Hilti
as a result, in whole or in part, of any violation by Customer of any Federal, State or Local statute or
regulation, or of any nationally accepted standard. It shall be Customers sole responsibility to
comply with all applicable laws and regulations regarding the handling, use, transportation, or
disposal of products upon taking possession of same.
AUTHORIZATION:
HILTI SALES REPRESENTATIVES ARE NOT AUTHORIZED TO MODIFY THESE TERMS AND CONDITIONS,
WARRANT SPECIFIC APPLICATIONS, OR EXECUTE CUSTOMER DOCUMENTS.
Reference/Conversion Tables
Hilti Center Directory I Online Store Locator www.us.hilti.com/stores
Customer Service 1-800-879-8000 (M-F, 6:00 am - 8:00 pm CST)
for their knowledge of various trades.
1-800-879-8000
www.us.hilti.com
Hilti, Inc. (US) 1-800-879-8000

Direct access to highly trained customer
service teams that can provide immediate
service for:
Quotes
Processing orders
Pricing
Technical information
Order and inventory status
FT. LAUDERDALE
5601 N Powerline Rd, #102
Ft Lauderdale FL 33309
JACKSONVILLE
2517 Edison Ave
Jacksonville FL 32204
MIAMI
7210 NW 25th St
Miami FL 33122
ORLANDO
4374 L.B. McLeod Rd, #6
Orlando FL 32811
TAMPA
5011 W Hillsborough Ave, Ste K
Tampa FL 33634
Maryland
BALTIMORE
175 W Ostend St, Unit D
Baltimore MD 21230
BELTSVILLE
11602 Baltimore Ave
Beltsville MD 20705
Michigan
DETROIT
28190 Schoolcraft Rd
Livonia MI 48150
FLINT
3433 Lapeer Rd
Flint MI 48503
GRAND RAPIDS
640 44th St SW
Grand Rapids MI 49508
Minnesota
MINNEAPOLIS
2575 University Ave West, #120
St. Paul MN 55114
Missouri
ST. LOUIS
3637 N Lindbergh Blvd
St. Ann MO 63074
Georgia
North Carolina
ATLANTA MIDTOWN
1050 Marietta St NW
Atlanta GA 30318
ATLANTA SUPER
6155-H Jimmy Carter Blvd
Norcross GA 30071
CHARLOTTE
801 Clanton Rd, Ste 113
Charlotte NC 28217
RALEIGH
628 Hutton St, Ste 105
Raleigh NC 27606
CINCINNATI
2736 E Kemper Rd, Bldg A
Cincinnati OH 45241
CLEVELAND
5400 Transportation Blvd
Garfield Heights OH 44125
COLUMBUS
818 Rose Ave
Columbus OH 43219
Oklahoma
OKLAHOMA CITY
411 N Meridian
Oklahoma City OK 73107
TULSA
10660 E 31st St
Tulsa OK 74146
Oregon
PORTLAND
316 SE Taylor St
Portland OR 97214
Pennsylvania
PHILADELPHIA
1618 S Columbus Blvd
Philadelphia PA 19148
PITTSBURGH
1301 Beaver Ave
Pittsburgh PA 15233
18
18
16
16
2.1-3.4
18
18
18
16
16
14
3.5-5.0
18
18
16
14
12
12
18
16
14
14
12
10
16
14
12
10
10
12.1-16.0
14
12
10
10
16.1-20.0
12
12
10
20.1-25.0
12
10
10
Utah
5.1-7.0
SALT LAKE CITY

2180 South 300 West, #108
Salt Lake City UT 84115
7.1-12.0
Virginia
CHESAPEAKE
200 Tintern Court, 101
Chesapeake VA 23320
FAIRFAX
2800 Gallows Rd, Ste F
Vienna VA 22180
RICHMOND
4203 W Broad St
Richmond VA 23230
Washington
KIRKLAND
11251 120th Ave NE
Kirkland WA 98033
SEATTLE
555 S Lander St, Ste 1
Seattle WA 98134
Wisconsin
MILWAUKEE
1461 S 108th St
West Allis WI 53214
Puerto Rico
PUERTO RICO
Calle Calaf #31, Parque Ind. (Tres
Monjitas)
Hato Rey PR 00918
Rhode Island
PROVIDENCE
155 Jefferson Blvd
Warwick RI 02888
Fractional to
Decimal
Conversion
Fraction Decimal
1/64
1/32
3/64
1/16
5/64
3/32
7/64
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
180
170
18
110
BOSTON
60 Arsenal St
Watertown MA 02472
Ohio
18
0.015
0.031
0.046
0.062
0.078
0.093
0.109
0.125
0.140
0.156
0.171
0.187
0.203
0.218
0.234
0.250
Screw
Diameter Gauge
90
Florida
Massachusetts
0-2.0
Fraction Decimal
80
Hilti team members are highly trained and known worldwide
NEW ORLEANS
5630 Jefferson Hwy
Harahan LA 70123
25' 50' 75' 100' 150' 200'
#6
#8
#10
#12
#14
0.138
0.164
0.190
0.216
0.242
70
manufacturers, sells and supports their products directly.
Louisiana
Tool
Ampere
Rating
60
HARTFORD
304 Murphy Rd
Hartford CT 06114
STAMFORD
87 Harvard Ave
Stamford CT 06902
LOUISVILLE
4524 Bishop Lane
Louisville KY 40218
Extension Cord Ordering Information

Hilti extension cords are UL Listed and meet
OSHA requirements for indoor and outdoor use.
For product information, see Drilling & Demolition (2)
or Diamond Coring, Cutting & Sawing (3)
40
Connecticut
Kentucky
BUFFALO
1000 Young St, Ste 490
Tonawanda NY 14150
HAUPPAUGE
11 Central Ave
Hauppauge NY 11788
MANHATTAN (Downtown)
76 9th Ave
New York NY 10011
MANHATTAN (Uptown)
1819 Second Ave
New York NY 10128
QUEENS
40-15 Northern Blvd
Long Island City NY 11101
30
company in the industry who researches, develops,
KANSAS CITY
1845 Foxridge Drive
Kansas City KS 66106
WICHITA
1703 SW Blvd
Wichita KS 67213
New York
20
DENVER
5855 Stapleton Dr North,
Unit A-160
Denver CO 80216
Kansas
contact with our customers is so important. Hilti is the only
INDIANAPOLIS
4086 Pendleton Way
Indianapolis IN 46226
Colorado
Indiana
160
AUSTIN
9010 IH 35 North, #116
Austin TX 78753
DALLAS
13635 Stemmons Fwy, #100
Farmers Branch TX 75234
EL PASO
7230 Gateway Blvd E, Unit C
El Paso TX 79915
FORT WORTH
2400 Meacham Blvd,
Ste G
Fort Worth TX 76106
HOUSTON NORTH
13240 Hempstead,
Ste 224
Houston TX 77040
HOUSTON SOUTH
8555 Knight Rd
Houston TX 77054
SAN ANTONIO
2411 NE Loop 410,
Ste 102
San Antonio TX 78217
150
Texas
HACKENSACK SUPER
263 S River St
Hackensack NJ 07601
PERTH AMBOY
788 Convery Blvd
Perth Amboy NJ 08861
BURBANK
2907 Empire Ave
Burbank CA 91504
LOS ANGELES
3310 Garfield Ave
Commerce CA 90040
OAKLAND
842 66th Ave
Oakland CA 94621
ORANGE
1070 N Batavia Ave,Ste D
Orange CA 92867
SACRAMENTO
3500 Power Inn Rd, Ste C
Sacramento CA 95826
SAN DIEGO
8303 Clairemont Mesa Blvd, Ste
101
San Diego CA 92111
SAN FRANCISCO
180 Pennsylvania
San Francisco CA 94107
SAN JOSE
691 E Brokaw Rd
San Jose CA 95112
140
New Jersey
California
130
NASHVILLE
561 Murfreesboro Rd
Nashville TN 37210
120
Tennessee
LAS VEGAS
5480 S Valley View Blvd, #140
Las Vegas NV 89118
100
Nevada
CHICAGO NORTH
451 S Busse Rd
Elk Grove Village IL
60007
CHICAGO SOUTH
6343 W 95th St
Oak Lawn IL 60453
50
Illinois
PHOENIX
325 S 48th St, Ste 106
Tempe AZ 85281
An undersized cord will cause a drop in voltage,

resulting in loss of power and overheating of the
tool. Use an extension cord heavy enough to carry
the current your tool requires. A heavier gauge
extension cord is required as the distance from the
electrical supply outlet increases.
To determine the proper size and length of extension cord, first refer to the ampere rating shown on
the tool nameplate. Apply this value to the chart at
right showing the recommended American Wire
Gauges (AWG) for use with electric tools. Always
use UL Listed extension cords. When in doubt, use
the next heavier gauge (the smaller the gauge, the
heavier).
0
10
Millimeters
Arizona
Choosing Extension Cord Wire Size (AWG)
COLUMBIA
1424 Bluff Rd
Columbia SC 29201
OMAHA
8310 F St
Omaha NE 68127
HONOLULU
1199 Dillingham Blvd
Honolulu HI 96817
call.
ANCHORAGE
7655 King St
Anchorage AK 99518
drive our actions which is why close personal
South Carolina
Metric Conversion Ruler
at Hilti, our customers requirements
Nebraska
Inches
0
there
Hawaii
Wire Size
Hilti is
Alaska

Cutting & Sawing
Screw Fastening Systems
Powder Actuated Systems
Mechanical & Adhesive Anchoring Systems
Strut & Hanger Installation Systems
Firestop Systems
Foam Systems

P.O. Box 21148, Tulsa, OK 74121
Customer Service 1-800-879-8000
Fax 1-800-879-7000
In Canada call 1-800-363-4458
Specials
Hilti is an equal opportunity employer.

Hilti is a registered trademark of Hilti, Corp.
Copyright 2003 by Hilti, Inc. (U.S.)
H600 00099510 09/03 LB, DBS
Customer Service
1-800-879-8000
Customer Account #
Hilti, Inc. (U.S.) 5400 South 122nd East Avenue, Tulsa OK 74146
Fax (800) 879-7000 www.us.hilti.com
For reference and conversion charts see reverse.
www.us.hilti.com
*14001 US only
The data contained in this literature was current as of the date of publication. Updates and
changes may be made based on later testing. If verification is needed that the data is still current, please contact the Hilti Technical Support Specialists at 1-800-879-8000. All published load
values contained in this literature represent the results of testing by Hilti or test organizations.
Local base materials were used. Because of variations in materials, on-site testing is necessary
to determine performance at any specific site.
Customer Service 1-800-879-8000 I www.us.hilti.com I Systems and Solutions I 2003-2004
Measuring Systems
Bookmarks provide
an additional form of
navigation through
the interface. Clicking
a bookmark will
take you directly to
that page.
This window shows

what page you are
currently on. By clicking and typing in the
page number here,
you can instantly go
to any desired page
in the book.
The ARROW tools

allow you to flip
through pages or
return instantly to the
first or last page just
like in a book.
The GO TO PREVIOUS
VIEW tool will take
you to your previously viewed page, even
if it is in a different
section of the CD.
Any time this hand

turns into a pointing
finger, you are over a
link. This means you
can click on it to go
to that topic or
Web site.

HILTI System &amp; Solution

Uploaded by

Copyright:

Available Formats

You might also like

HILTI System &amp; Solution

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HILTI System &amp; Solution

Uploaded by

Copyright:

Available Formats

expertise. in every case.

Drilling & Demolition Systems

expertise. in every case.

expertise. in every case.

For reference and conversion charts see reverse.

Hilti Tool Support Program

Customer Service 1-800-879-8000 I www.us.hilti.com I Systems and Solutions I 2002-2003

Laser Measuring & Positioning Systems

Table of Contents I Ordering Information I Hilti Centers I Help

Hilti Center Directory I Online Store Locator www.us.hilti.com/stores

Customer Service 1-800-879-8000 (M-F, 6:00 am - 8:00 pm CST)

for their knowledge of various trades.

Hilti, Inc. (US) 1-800-879-8000

SALT LAKE CITY

Hilti team members are highly trained and known worldwide

Extension Cord Length

25' 50' 75' 100' 150' 200'

expertise. in every case.

manufacturers, sells and supports their products directly.

Extension Cord Ordering Information

company in the industry who researches, develops,

contact with our customers is so important. Hilti is the only

An undersized cord will cause a drop in voltage,

Choosing Extension Cord Wire Size (AWG)

drive our actions which is why close personal

Metric Conversion Ruler

at Hilti, our customers requirements

Local Hilti Centers provide convenience

Customer Service 1-800-879-8000 (M-F, 6:00 am 8:00 pm CST) | www.us.hilti.com

More than 800 Sales Representatives

expertise. in every case.

More Productivity with Less Administration

For companies with large tool fleets, the acquisition,

With Hilti Fleet Management you can afford to

How The Hilti Fleet Management

Systems & Solutions

Drilling & Demolition Systems

Diamond Coring, Cutting & Sawing Systems

Wood Cutting & Sawing, Specialty Drilling

Screw Fastening & Drill Driver Systems

Direct Fastening Systems

*14001 U.S. only

The data contained in this catalog was current

Foam & Construction Chemicals

Terms & Conditions of Sale

Hilti Tool Support

Hilti Tool Support Program

The Hilti Full Service Tool Support Program includes:

As of January 2001, with the purchase of

Look for the Full Service icon located on

Hilti Tool Repair

*Typical turnaround time

Total Tool Service

Easily Fasten Into

GX 100 Gas-Driven Fastening System

GX 100 Gas-Driven Fastening Tool

Supplied in an impact resistant plastic Hilti case with

X-GM 40 Nail Magazine

HILTI System & Solution

HILTI System & Solution

HILTI System & Solution