Professional Documents
Culture Documents
Dias NT
Dias NT
Introduction
Figure 1
DIAS Architecture
The DIAS has a Digital Subscriber Unit (DSU) that combines voice and
Internet data packets on a single twisted-pair wire at the subscribers premises. At the
service providers premises, the Integrated Access Node (IAN) separates voice and
data traffic from a number of subscribers and routes them independently to the PSTN
and the Internet respectively. Apart from this DIAS supports a Lifeline option, which
provides a simple telephone service in the case of power failure or any problem in the
customer premises modem. The IAN is connected to the PSTN via an E1 voice port
when V5.2 protocol is running between the DIAS and the PSTN switch, and to the
Internet either through E1 data ports or through an Ethernet port. In the case of V5.2
protocol the lifeline unit is a separate unit will be catering for 240 Lines. Alternatively
the PSTN connectivity can be achieved through POTS lines with the addition of an
optional 2-wire lifeline unit that converts a single E1 line to 30 POTS lines. This unit
is capable of support 120 subscribers per sub rack
The DIAS system as shown in figure 2 below provides two types of voice and
data services to the customer
Figure 2
The BDSU (Basic Digital Subscriber Unit) is designed for the SOHO (Small
Office Home Office) and residential Internet user. It provides a permanent
Internet connection at a maximum data rate of 128 kbps, which drops to 64
kbps when the telephone is in use and transparently, goes back to 128 kbps
when the telephone goes on-hook.
The HDSU (High bit rate Digital Subscriber Unit), which is designed for
corporate subscribers, can provide voice connectivity for a telephone and
permanent data connectivity of up to 2 Mbps. The Basic Rate DSU (BDSU)
located at the subscriber's premises has a telephone interface (RJ11) and an
Ethernet port (RJ45) or a Serial Port to provide Internet Access. The High Bit
Rate DSU (HDSU) has an Ethernet port and 4/8 Telephone Interfaces (RJ11), thus
having the ability to connect to 4 or 8 independent telephones at a corporate
office. The BDSU has local powering off the AC Mains (230V).
In the case of Power failure the system will offer simple POTS connection. The
Ethernet port providing Internet access is off during power failure.
The BDSU and the HDSU are connected to the Integrated Access Node,
located either at a street corner (curb) or at the central office, using a twisted pair
copper wire. For the BDSU, the maximum length of the copper can be 3.5 km when
0.4- mm-twisted pair copper is used. 128 kbps Internet access can be provided on the
BDSU Ethernet port in such a configuration when the telephone is not being used.
The Internet access rate seamlessly drops to 64kbps when the BDSU telephone is
being used providing the telephone a 64kbps circuit-switched access. The HDSU is
also connected using copper to the IAN. The maximum rate at which Internet Access
is provided to the HDSU Ethernet port is 2 Mbps, and this is possible when the length
of the copper is less than 2 Km (0.4mm twisted pair copper). The bit-rate on the
HDSUIAN link drops for higher lengths of copper, thus reducing Internet access rate
on the HDSU Ethernet port. Each telephone on the HDSU uses 64kbps when off-hook
and reduces the bit-rate of the HDSU Internet access by the same amount. In on-hook
mode, the Internet access rate seamlessly reverts to the original value. Figure 3 shows
various cards of the IAN
Figure 5
3.0
Stacking of more than one IAN is required in the case where a higher number
of subscribers are concentrated through the same voice-E1 and data-E1 lines. The
stacking strategy differs for voice and data. Stacking for Data Stacking of IANs for
data is carried out over the Ethernet backbone. Four IANs can be stacked to serve a
maximum of 240 subscribers. A proprietary stack management protocol distributes
the routing table to the IANs connected through the backbone. Thus, over a period of
time, all the IANs will get complete information about all the other IANs that are
connected to the backbone. One of the IANs connected to the E1 link of the ISP is
considered as the default gateway by the other IANs. Stacking for Voice Two voice
E1 lines connected to the exchange, is shared by all other IANs in a stack as shown in
the figure 6. Each IAN is allocated a few slots on the E1 link. Individual IANs
establish and receive calls using the slots allocated to them. Basically, each IAN acts
like a drop/insert multiplexer for those slots. A Distributed V5.2 stack is run across
the IANs. Out of the 8E1 ports two are used for the data and two are used for the
stacking and the remaining 4E1s are used for the Lifeline units
.
Figure 6 Stacking for Data and Voice
10