Professional Documents
Culture Documents
Sep Ed 303004 en
Sep Ed 303004 en
SEPED303004EN 01/2013
Logipam
SFT2885 Programming Software
for Sepam Series 80
Users Manual
SEPED303004EN
01/2013
www.schneider-electric.com
SEPED303004EN 01/2013
Document Set
Structure of this Manual
This manual consists of 7 chapters and 2 appendices:
SEPED303004EN 01/2013
SEPED303004EN 01/2013
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction to the Logipam Software . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registering the Logipam Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Method of Creating and Operating a Logipam Program . . . . . . . . . . . . . .
SEPED303004EN 01/2013
9
11
13
14
15
16
17
19
20
21
22
24
25
26
27
28
29
30
32
33
34
35
36
38
40
41
42
44
46
48
Coils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comment Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rules for Executing the Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
53
54
55
59
60
62
63
66
68
70
71
72
74
76
81
83
85
86
87
90
92
94
97
98
100
102
104
105
108
110
111
112
113
114
117
119
123
124
125
126
129
SEPED303004EN 01/2013
131
132
134
136
143
145
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
147
Appendix A Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
149
SEPED303004EN 01/2013
150
154
156
159
164
SEPED303004EN 01/2013
Safety Information
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
SEPED303004EN 01/2013
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the construction
and operation of electrical equipment and its installation, and has received safety
training to recognize and avoid the hazards involved.
10
SEPED303004EN 01/2013
At a Glance
Document Scope
This manual describes how to use Logipam in MS Windows to create control system
programs for Sepam series 80 protection relays.
It explains how the software works, its programming language, programming
elements, creation and simulation of programs and also program operation.
Who is This Manual Aimed at?
This document is aimed at design office personnel who wish to create a control
system program, and at anyone involved in setting up control system programs and
maintaining them on Sepam series 80 protection relays.
Knowledge Required
The creation and setup of a Logipam control system program requires knowledge of
the MS Windows environment and applied control system projects.
Validity Note
Conditions of Use for the Logipam Software
Logipam can only be used to develop control system programs for Sepam series
80.
A cartridge with the Logipam SFT080 option must be used on the Sepam when
executing control system programs developed with Logipam.
Functions programmed using another editor are not compatible with Logipam
programmed functions.
Environment Supported
Logipam runs on PCs with the following operating systems:
Windows 2000
Windows XP
Only Sepam series 80 protection relays with a cartridge including the Logipam
SFT080 option are capable of executing the control and monitoring functions with
the Logipam SFT2885 software.
SEPED303004EN 01/2013
11
Related Documents
Title of Documentation
Reference Number
SEPED303001FR
SEPED303001EN
SEPED303002FR
SEPED303002EN
SEPED303003FR
SEPED303003EN
63230-216-230
63230-216-231
63230-216-229
You can download these technical publications and other technical information from
our website at www.schneider-electric.com.
User Comments
We welcome your comments about this document. You can reach us by e-mail at
[email protected].
12
SEPED303004EN 01/2013
Logipam
Introduction to the Logipam Software
SEPED303004EN 01/2013
SEPED303004EN 01/2013
Page
Introduction
14
15
Architecture
16
17
13
Introduction
General
Logipam (SFT2885 software) is used to program control system functions for
Sepam series 80.
Logipam runs in MS Windows.
Programming Language
The programs are created in Ladder language.
Ladder language is a graphic language used to transcribe ladder diagrams. It uses
the basic graphic symbols of a diagram: contacts, coils and connections.
When Should Logipam Be Used?
Logipam is used to create specific functions or to complement Sepam predefined
functions.
NOTE: Each Sepam contains the appropriate predefined functions for the chosen
application.
Composition of the Logipam Software
Logipam consists of:
14
SEPED303004EN 01/2013
It is possible for the license rights to be transferred to another user from a different
company.
SEPED303004EN 01/2013
15
Architecture
Introduction
Logipam is used to create, simulate and generate control system programs. The
programs are then set up and operated with the aid of SFT2841 and Sepam.
Hardware and Software Architecture
The hardware and software architecture requires the creation of a control system
program that consists of:
16
SEPED303004EN 01/2013
Description
SEPED303004EN 01/2013
17
With SFT2841:
in disconnected mode to configure Sepam with the Logipam program
18
The parameters of the objects used in the program and the configuration bits can
be set in both modes.
From the Sepam interface during operation, to monitor program execution
SEPED303004EN 01/2013
Logipam
Description of Logipam Variables and Objects
SEPED303004EN 01/2013
SEPED303004EN 01/2013
Page
Introduction
20
21
Logic Inputs
22
Remote Controls
24
Predefined Inputs
25
Protection Outputs
26
Memorized Bits
27
Non-memorized Bits
28
Configuration Bits
29
Logic Outputs
30
Predefined Outputs
32
Outputs to Matrix
33
Protection Inputs
34
Remote indications
35
Timers
36
Counters
38
Clocks
40
19
Introduction
General
Ladder language consists of Boolean variables and Logipam objects.
The three types of Boolean variable are:
Logipam inputs
Logipam internal variables
Logipam outputs
20
SEPED303004EN 01/2013
An invariable identifier
A name
A comment
Predefined
Predefined variables (predefined inputs and outputs as well as protection inputs
and outputs) have a predefined invariable name and comment.
Free entry
Each unpredefined variable or each object can be identified by a name and a
comment in free text, to make the program easier to understand. It is not
compulsory to enter a name or comment. It is entered in the variable or object
parameter-setting window. For further information on inserting comments, see
Defining Variables and Objects, page 87.
SEPED303004EN 01/2013
21
Logic Inputs
Definition
"Logic input" variables are Logipam input variables; they are divided into two
categories:
"Logic images" of the electrical state of the Sepam MES120 module inputs (IXYY)
GOOSE (GXYY) logic inputs used by the protocol IEC 61850
They can only be used in the program contact zone.
The logic inputs are updated at the start of each program execution cycle.
Identification
The logic inputs are identified by:
An identifier:
IXYY for the MES120 module logic inputs, for example I105
GXYY for the GOOSE logic inputs, for example G403
A name
A comment
22
SEPED303004EN 01/2013
Use
A logic input that is not present or is declared "unused" in SFT2841 is always at 0.
The logic inputs used only in Logipam should be assigned as "Other use" in
SFT2841.
If a name has been allocated to the input in Logipam, this name appears in the input
assignment table in SFT2841, instead of "Other use".
SEPED303004EN 01/2013
23
Remote Controls
Definition
"Remote control" variables are Logipam input variables. These are logic orders sent
by a remote system (a supervisor, for example) to Sepam by the communication
system.
The 96 available remote controls are divided into two categories:
A name
A comment
24
SEPED303004EN 01/2013
Predefined Inputs
Definition
"Predefined input" variables are Logipam input variables. These derive from the
Sepam predefined functions.
They can only be used in the program contact zone.
Identification
The predefined inputs are identified by:
An identifier, SIxxx
A name
A comment
The name and the comment are predefined and cannot be modified.
The exhaustive list of predefined inputs is provided in the appendix and gives a
complete identification of each predefined input (identifier, name and comment)
together with the predefined function from which it derives.
For example:
Identifier: SI087
Name: V_OPG_ON
Comment: Disturbance recording on
Derives from the function: Disturbance recording
Use
Predefined functions are available in each Sepam depending on the chosen
application: not all the predefined functions are processed by all Sepams.
If a predefined input is used in the Logipam program even though the associated
function is not processed by Sepam, the value of this input is always 0.
SEPED303004EN 01/2013
25
Protection Outputs
Definition
"Protection output" variables are Logipam input variables.
They can only be used in the program contact zone.
Identification
Protection outputs are identified by:
An identifier PXX_Y_ZZ, where:
XX is the ANSI protection code
Y is the number of the protection unit
ZZ is the variable sequence number, between 01 and 99
The name and the comment are predefined and cannot be modified.
The exhaustive list of protection outputs is provided in the appendix.
For example:
Identifier: P50/51_2_7
Name: P50/51_2_7
Comment: Protection 50/51 Unit 2 Phase 1 fault.
Use
Protection functions are available in each Sepam depending on the chosen
application: not all the protection functions are processed by all Sepams.
If a protection output is used in the Logipam program although the associated
function is not processed by Sepam, the value of this output is always 0.
26
SEPED303004EN 01/2013
Memorized Bits
Definition
The 128 "Memorized bit" variables are Logipam internal variables. The state of a
memorized bit is saved on loss of the Sepam auxiliary power supply.
They can be used in both the program contact zone and coil zone.
Identification
Memorized bits are identified by:
An identifier, MS001 to MS128
A name
A comment
The name and the comment can be modified.
Use
Memorized bits can be viewed during operation with the aid of SFT2841.
SEPED303004EN 01/2013
27
Non-memorized Bits
Definition
The 512 "Non-memorized bit" variables are Logipam internal variables. The state of
a non-memorized bit is not saved on loss of the Sepam auxiliary power supply and
is 0 on each energization.
They can be used in both the program contact zone and coil zone.
Identification
Non-memorized bits are identified by:
An identifier, MX001 to MX512
A name
A comment
28
SEPED303004EN 01/2013
Configuration Bits
Definition
The 64 "configuration bit" variables are Logipam internal variables. The state of a
configuration bit is saved on loss of the Sepam auxiliary power supply.
They can be used in both the program contact zone and coil zone.
Identification
Configuration bits are identified by:
An identifier, MP01 to MP64
A name
A comment
The name and the comment can be modified.
Use
Configuration bits are used to configure the Logipam program processing.
For example, configuration bit MP01 can be used to set the parameters of the
switchgear control to the type of breaking device where:
SEPED303004EN 01/2013
29
Logic Outputs
Definition
"Logic output" variables are Logipam output variables.
They can be used in both the program contact zone and coil zone.
Identification
Logic outputs are identified by:
An identifier, OXYY
A name
A comment
Sepam performs a logical OR on these three orders from different sources to control
the output relay.
NOTE: A single logic output should never be controlled from these different
functions.
We recommend that each logic output is controlled from a single function, and that
predefined I/O are used to interface data sent by other functions.
The state of "Logic output" variables is only determined by their processing in the
Logipam program.
30
SEPED303004EN 01/2013
The "Logic output" variables that are not controlled by Logipam have state 0.
The state of a "Logic output" variable is not necessarily the "logic image" of the
electrical state of the Sepam output.
Example: O101 is controlled by Logipam and the control matrix.
SEPED303004EN 01/2013
If O101=1 for Logipam and O101=0 for the control matrix, then the Sepam O101
output is controlled and logic output variable O101=1 for Logipam
If O101=0 for Logipam and O101=1 for the control matrix, then the Sepam O101
output is controlled but logic output variable O101=0 for Logipam
31
Predefined Outputs
Definition
"Predefined output" variables are Logipam output variables.
Logipam predefined outputs are Sepam predefined function inputs.
They can be used in both the program contact zone and coil zone.
Identification
Predefined outputs are identified by:
An identifier, SOxxx
A name
A comment
The name and the comment are predefined and cannot be modified.
The exhaustive list of predefined outputs is provided in the appendix and gives a
complete identification of each predefined output (identifier, name and comment) as
well as the function to which it is assigned.
For example:
Identifier: SO057
Name: V_CLOSECB
Comment: circuit breaker closing order - Switchgear control function input
Function input: Switchgear control
Use
Predefined functions are available in each Sepam depending on the chosen
application: not all the predefined functions are processed by all Sepams.
If a predefined output is used in the Logipam program even though the associated
function is not processed by Sepam, the value of this output is not processed.
32
SEPED303004EN 01/2013
Outputs to Matrix
Definition
The 128 "Output to matrix" variables are Logipam output variables to be linked to the
control matrix inputs.
They can be used in both the program contact zone and coil zone.
Identification
Outputs to matrix are identified by:
An identifier, MAT001 to MAT128
A name
A comment
The name and the comment can be modified.
Use
Outputs to matrix can be accessed in the SFT2841 "Control matrix" screen with the
Logipam button.
They can be used to control:
SEPED303004EN 01/2013
33
Protection Inputs
Definition
"Protection input" variables are Logipam output variables.
They can be used in both the program contact zone and coil zone.
Identification
Protection inputs are identified by:
An identifier PXX_Y_ZZZ, where:
XX is the ANSI protection code
Y is the number of the protection unit
ZZZ is the variable sequence number, between 100 and 199
The name and the comment are predefined and cannot be modified.
The exhaustive list of protection inputs is provided in the appendix.
For example:
Identifier: P12_1_101
Name: P12_1_101
Comment: Protection 12 Unit 1 Reset
Use
Protection functions are available in each Sepam depending on the chosen
application: not all protection functions are processed by all Sepams.
If a protection input is used in the Logipam program even though the associated
function is not processed by Sepam, the value of this input is not processed.
34
SEPED303004EN 01/2013
Remote indications
Definition
The 240 "Remote indication" variables are Logipam output variables. These are
logic data items sent by Sepam to a remote system (a supervisor, for example) by
the communication system.
They can be used in both the program contact zone and coil zone.
Identification
Remote indications are identified by:
An identifier, TS001 to TS240
A name
A comment
The name and the comment can be modified.
Use
Remote indications are used:
By predefined control and monitoring functions: each remote indication is
preassigned to a logic data item resulting from the processing of a predefined
function.
Or by Logipam: any logic data item can be assigned to each remote indication
Once a remote indication is used by Logipam, it is no longer generated by the
predefined function to which it has been assigned.
SEPED303004EN 01/2013
35
Timers
Definition
60 "Timer" objects are available in Logipam.
They can be used:
Identification
Timers are identified by:
A predefined identifier, T01 to T60
A name
A comment
A status variable
A control instruction (TON or TOF)
The "duration" parameter
The duration setting range
State of a Timer
The status variable follows the state at the start of the timer with an on-delay or offdelay.
The status variable is used in the contact zone, and is identified as the object.
A Timer TON or TOF Control Instruction
Two special instructions can be used to control a timer to be used in the coil zone.
However, a timer can only have one coil on the whole diagram.
36
SEPED303004EN 01/2013
Control
TON timer
Start of an on-timer, on the rising edge of the
associated condition programmed in the contact zone.
TOF timer
Start of an off-timer, on the falling edge of the
associated condition programmed in the contact zone.
Duration of a Timer
The duration of each timer can be set between 0 and 650000 ms in 10 ms steps:
Setting Range
The timer duration setting range is used to fix the maximum and the minimum value
of this duration.
This defined setting range is used to limit the values allowed for the timer duration
during setting with SFT2841.
SEPED303004EN 01/2013
37
Counters
Definition
24 "Counter" objects are available in Logipam.
Identification
Counters are identified by:
An identifier, C01 to C24
A name
A comment
A status variable
A current value
Two control instructions
The "set point" parameter
State of a Counter
The status variable is:
Control
Increments the counter by one unit.
38
SEPED303004EN 01/2013
The set point of each counter must be set between 0 and 65535.
Viewing the Current Value
The current value of the counters can be viewed:
SEPED303004EN 01/2013
39
Clocks
Definition
4 "Clock" objects are available in Logipam.
Clocks are used to generate periodic pulses with a weekly cycle to trigger periodic
actions.
Identification
Clocks are identified by:
An identifier, H01 to H04
A name
A comment
A status variable
The following parameters:
A start time, configurable in hours/minutes/seconds
A period, configurable in hours/minutes/seconds
A number of pulses per day, less than 1440
The days of the week on which the pulses will be generated
For example, to generate 4 pulses every Monday and Wednesday at 08.00, 11.00,
14.00 and 17.00, a clock must be set with the following parameters:
State of a Clock
On each pulse, the status variable is at 1 for one cycle duration.
The status variable is used in the contact zone.
Setting a Clock
The parameters can be set for each clock:
40
SEPED303004EN 01/2013
Logipam
Ladder Language
SEPED303004EN 01/2013
Ladder Language
3
Scope of This Chapter
This chapter describes the general principles of Ladder language.
What Is in This Chapter?
This chapter contains the following topics:
Topic
SEPED303004EN 01/2013
Page
42
Diagram Structure
44
Contacts
46
Connections
48
Coils
49
Comment Lines
53
54
Programming Tips
55
41
Ladder Language
42
SEPED303004EN 01/2013
Ladder Language
By analogy with an electrical diagram, the coils are executed if they are linked by a
passing connection on the left-hand potential bar.
Ladder Language Instructions
Logipam Ladder language has three types of instruction:
Contacts
Connections
Coils
Ladder diagrams can contain a maximum of 5000 contacts and coils.
Basic Principles of Ladder Language Programming
The programming principles are as follows:
Connections are always passing
The different types of contact are passing, depending on the value of the
associated variable
The combination of series and parallel contacts via connections is used to
program the logic conditions for executing coils
SEPED303004EN 01/2013
43
Ladder Language
Diagram Structure
General
A Ladder diagram is drawn between two potential bars (a) and (b).
The current flows from the left-hand potential bar (a) to the right-hand potential bar
(b).
Illustration
The figure below illustrates the representation of the Ladder diagram between the
potential bars.
44
SEPED303004EN 01/2013
Ladder Language
10 columns
9 columns representing the contact zone in which the conditions necessary for
an action appear
1 column representing the zone for the coil that performs the action following
a sequence of tests in the contact zone
Cells
The intersections of lines and columns are cells.
A cell can contain a contact, a connection or a coil.
Sections
To structure a program and make it easy to read, the lines can be grouped in
sections and sub-sections.
Lines can be grouped in a maximum of 100 sections.
A section can contain two levels of sub-section.
Sections and sub-sections are numbered, and can be allocated a title.
Execution of a section may be conditioned by a variable. The section will or will not
be executed according to the value of the selected variable, as follows:
SEPED303004EN 01/2013
45
Ladder Language
Contacts
Definition
Contact type instructions are positioned on a cell, in the contact zone.
Contacts are used to test the state of variables.
Description
The 4 types of contact and their functions are indicated in the table below.
Type
46
Illustration
Function
Normally passing
contact
SEPED303004EN 01/2013
Ladder Language
Examples
Logipam program
SEPED303004EN 01/2013
47
Ladder Language
Connections
Definition
Connections are used to link up the contacts and coils.
They are represented by lines.
Description
The types of connection and their functions are indicated in the table below.
Type
48
Illustration
Function
Horizontal
connection
Vertical
connection
SEPED303004EN 01/2013
Ladder Language
Coils
Definition
Coil-type instructions are positioned on a cell, in the coil zone.
A coil is active when at least one closed string of contacts and connections links it
to the left-hand potential bar.
Coils for Action on Variables
The types of coil and their functions are indicated in the table below.
Type
SEPED303004EN 01/2013
Illustration
Function
Direct coil
Inverse coil
Set coil
Reset coil
49
Ladder Language
Examples
Logipam program
50
Illustration
Function
TON timer
TOF timer
SEPED303004EN 01/2013
Ladder Language
Examples
Logipam program
Illustration
Function
Counter
Reset counter
Example
Logipam program
SEPED303004EN 01/2013
51
Ladder Language
52
SEPED303004EN 01/2013
Ladder Language
Comment Lines
General
Comment lines make it easier to read and interpret the diagram, but they are not
compulsory.
Description
The comment is integrated in the diagram. It consists of a maximum of 3 lines of 60
characters each.
400 comment lines are available.
Illustration
The figure below shows the position of the comment.
SEPED303004EN 01/2013
53
Ladder Language
54
Variable=0, the section is not executed in the program, the variables that could
have been modified inside the section retain their value
Variable=1, the section is executed in the program
SEPED303004EN 01/2013
Ladder Language
Programming Tips
Using Coils
All coils encountered are executed, so a single counter used twice is interpreted
twice.
A single coil can take several values during an execution cycle. However, only the
value at the end of execution is retained, as the intermediate values are replaced
each time there is a new coil. In the example below, MX001 takes the value I101
during the cycle and the value I102 at the end of execution.
Order of Coils
The order of the coils is important. The examples below illustrate the differences in
evaluation according to the order of the coils.
SEPED303004EN 01/2013
55
Ladder Language
Example 1
Example 2
56
SEPED303004EN 01/2013
Ladder Language
SEPED303004EN 01/2013
57
Ladder Language
58
SEPED303004EN 01/2013
Logipam
Familiarization With the Software
SEPED303004EN 01/2013
4
Scope of This Chapter
This chapter describes the Logipam software and the initial operations for getting
started.
What Is in This Chapter?
This chapter contains the following topics:
Topic
SEPED303004EN 01/2013
Page
60
Importing a Program
62
Software Options
63
Password Protection
66
68
70
Online Help
71
72
74
76
81
83
59
Opening Logipam
To open Logipam from the Windows menu, proceed as follows:
Step
Action
60
SEPED303004EN 01/2013
Check the Do not display this dialog box again box in the Welcome dialog box.
Or open the Options window from the File Options menu, and deselect the
Display welcome box box.
To re-enable it, open the Options window from the File Options menu, and
check the Display welcome box box.
Creating a New Program
To create a new program, proceed as follows:
Step
Action
In the Welcome dialog box, click the Create a new program button.
The Choice of editing language dialog box opens.
Action
In the Welcome dialog box, click the Open an existing program button.
The Open dialog box is displayed so you can select a program that has already
been created.
SEPED303004EN 01/2013
Action
Click OK.
The Logipam main window opens.
61
Importing a Program
Introduction
The Logipam program import function is used to retrieve a program from Sepam.
Functionality
During the import, the imported file is converted so that it can be used by Logipam.
The program is validated automatically.
Procedure
To import a program, proceed as follows:
Step
62
Action
Open Logipam.
Click OK.
A dialog box is displayed to tell you the result of the import.
SEPED303004EN 01/2013
Software Options
Introduction
The options available from the File Options menu can be used to customize use
of Logipam.
Description
The software options are as follows:
SEPED303004EN 01/2013
Action
Open Logipam.
The Logipam main window opens.
63
Step
Action
64
Action
Open Logipam.
The Logipam main window opens.
In the Diagram language drop-down menu, select the desired language and
click OK.
Important: Only information in the requested editing language is displayed. If
you select French as the diagram language but have previously entered text
with UK English as the diagram language, the UK English text will not be
displayed.
SEPED303004EN 01/2013
Action
Open Logipam.
The Logipam main window opens.
In the Refresh period field, enter the desired value and click on OK to close
again.
SEPED303004EN 01/2013
65
Password Protection
Introduction
Logipam allows a program to be protected with a password.
Description
The three levels of protection available are:
None
(Default protection level)
The program is not protected.
Read forbidden
The program is read-protected. You must enter a password to open it.
Modification forbidden
The program is write-protected. You can view it but you must enter a password
in order to save any modifications.
Procedure
To protect a program with a password, proceed as follows:
Step
66
Action
Open Logipam.
SEPED303004EN 01/2013
Step
SEPED303004EN 01/2013
Action
Click OK.
If you have selected the Read forbidden option, Logipam will ask you to enter
your password the next time the program is opened.
If you have selected the Modification forbidden option, Logipam will ask you
to enter your password the next time the program is saved.
Remark: To modify these options in the future, Logipam will ask you to enter
your password again.
67
Illustration
The figure below shows the Logipam main screen:
68
SEPED303004EN 01/2013
Description
The table below describes the Logipam main screen:
Label
Element
Function
Menu bar
Toolbar
On-line help
Programming zone
operation
SEPED303004EN 01/2013
Operating mode
Status bar
69
Description
The table below describes the icons available from the toolbar:
Icon
Function
Create a new project
Consistency check
Adjust zoom
NOTE: These functions can be accessed via the menus in both edit mode and
simulation mode.
70
SEPED303004EN 01/2013
Online Help
Presentation
The online help supplies information about using Logipam from all screens. It
consists of this document.
Access to the Online Help
There are two suggested access methods:
Icon
Access
Access from the icon on the menu bar to open the entire help file.
SEPED303004EN 01/2013
71
In edit mode: to access all the variables and objects available in order to place
them on the data entry grid
In simulation mode: simply to view the variables and objects used in the program
Description
The figure below shows the variables and objects bar:
Description
Logipam inputs
Internal bits
Timer objects
Clock objects
Counter objects
Logipam outputs
Use
When the cursor passes over an icon, a window appears presenting all the variables
or objects in the requested category.
72
SEPED303004EN 01/2013
For example, when the cursor passes over the Logipam inputs icon, the following
window opens:
SEPED303004EN 01/2013
73
Edit Mode
Edit mode is used to enter the program (default mode).
Simulation Mode
Simulation mode is used to simulate program execution, to check its operation,
and to make modifications to variables and objects.
Action
Simulation
74
SEPED303004EN 01/2013
SEPED303004EN 01/2013
75
76
SEPED303004EN 01/2013
Description
The figure below shows the screen in edit mode and the entry bar:
SEPED303004EN 01/2013
Button
Use
Diagram
Parameters
Variables
Used to enter the name and comment for all the variables.
77
78
SEPED303004EN 01/2013
Description
Indicates:
The identifier (ID) for the object, if you have selected display of
Parameters
Comments
Used to enter a text to add a comment to the object, by doubleclicking on the line.
Type
Only in the Timers tab: this information indicates whether the timer
is a TON or TOF type.
SEPED303004EN 01/2013
79
Description
Indicates:
The identifier (ID) for the object, if you have selected display of
Comments
Used to enter a text to add a comment to the variable, by doubleclicking on the line.
80
SEPED303004EN 01/2013
Illustration
The figure below illustrates the program in simulation mode :
SEPED303004EN 01/2013
81
Simulation Toolbar
The simulation toolbar looks like this:
Function
Initialize variables
Execute variables
Stop simulation
Simulation day
Simulation time
82
SEPED303004EN 01/2013
SEPED303004EN 01/2013
83
84
SEPED303004EN 01/2013
Logipam
Creating a Program
SEPED303004EN 01/2013
Creating a Program
5
Scope of This Chapter
This chapter describes all the operations involved in creating a program.
What Is in This Chapter?
This chapter contains the following topics:
Topic
Defining the Properties of a Program
86
87
Creating a Line
90
92
94
Section Title
97
SEPED303004EN 01/2013
Page
98
100
102
104
Copy/Paste Function
105
Search/Replace Function
108
110
111
112
Saving a Program
113
114
Program Checking
117
119
85
Creating a Program
List of Properties
The properties that can be assigned are as follows:
These properties appear when the cover page is printed. For reasons of traceability,
it is a good idea to enter them all.
The properties automatically assigned by Logipam are as follows:
86
Action
Open Logipam.
Click OK.
SEPED303004EN 01/2013
Creating a Program
Action
On the diagram grid, double-click on the variable to be defined.
A Parameter settings dialog box opens, as shown in the figure below for a
variable which has not been predefined.
87
Creating a Program
Step
2
Action
Enter the information and click OK.
Action
88
Action
SEPED303004EN 01/2013
Creating a Program
Action
Note
You can also open the Parameter-setting window as a contextual menu by rightclicking on the cell of the variable or the object.
SEPED303004EN 01/2013
89
Creating a Program
Creating a Line
Introduction
Creating a program line consists of:
Inserting elements
Select the variables or objects and place their graphic representation on a cell of
the grid as a contact or a coil.
For further information on graphic representations, see Ladder Language,
page 41.
Drawing the connections to link up the contacts and coils
In a diagram you can create horizontal or vertical connections between the
elements. The connections are represented by lines.
To link two elements, you should draw as many lines as there are blank cells
between the elements.
Modifying the operations on the contacts and coils.
Action
In the variables and objects bar, position the mouse cursor on the Logipam
inputs button, for example.
The dialog box corresponding to the Logipam inputs variables category
opens.
Select the type of variable, the Logic inputs tab for example.
A tree structure representing the logic inputs expands.
In the tree structure, select a logic input, for example input I102 of the
MES_120_1 module.
Click and drag input I102 onto a cell of the diagram, for example Contact 4
of line 0002.
The activated cell appears as a yellow rectangle in the diagram.
Creating Connections
To create a connection, see Creating and Deleting Connections, page 110.
90
SEPED303004EN 01/2013
Creating a Program
Modifying Functions
To modify the functions of elements placed as a contact or a coil, proceed as follows:
Step
SEPED303004EN 01/2013
Action
In the diagram, select the graphic element whose function you wish to modify.
91
Creating a Program
Action
Click on Edit Add a line after the selection or Add a line before the
selection, as appropriate.
A new line appears in the program. The number of the new line appears in the
line header in the grayed-out area to the left of the screen.
Notes:
1. To add a line, you can also right-click on the cell or the line, then select Add
a line after the selection or Add a line before the selection.
2. To add a line at the end of the program, you should scroll through the
program until you find the last line. Click on the icon representing a down arrow
below the last line of the program: a new line appears.
92
Action
Enter the number of lines you wish to insert (10 lines by default).
The new lines appear in the program before the selected line.
SEPED303004EN 01/2013
Creating a Program
Deleting Lines
To delete lines from a program, proceed as follows:
Step
SEPED303004EN 01/2013
Action
Click on Edit Delete, or right-click on the lines, then select the Delete option,
or use the <Del> key on your keyboard.
93
Creating a Program
94
Action
SEPED303004EN 01/2013
Creating a Program
Step
3
Action
Right-click on the line, then select the Define a section option.
The section appears on the line you have just selected.
A section expansion icon represented by a square appears in the line header
as shown in the figure below:
Action
Select the sections or the sections and lines you wish to form into one section.
Right-click on the sections and lines, then select the Define a section option.
The section appears on the sections or lines you have just selected.
Canceling a Section
Canceling a section or a sub-section deletes the section definition. The grouping of
lines by section is thus canceled, and the lines retain their content. To cancel a
section, proceed as follows:
Step
SEPED303004EN 01/2013
Action
95
Creating a Program
96
Action
SEPED303004EN 01/2013
Creating a Program
Section Title
Introduction
Once a section exists in a diagram, you can allocate it a title.
Procedure
To allocate a title to a section, proceed as follows:
Step
Action
You can also right-click on the section, then select the Parameter-setting
window option.
4
SEPED303004EN 01/2013
97
Creating a Program
Illustration
The figure below illustrates insertion of an execution condition:
98
SEPED303004EN 01/2013
Creating a Program
Creating a Condition
To allocate an execution condition to a section, proceed as follows:
Step
Action
Select the variable which will determine the section and drag it onto the section
header.
The identifier or the name of the variable appears in the section title bar (I101
in the example below).
Deleting a Condition
To delete the execution properties from a section, proceed as follows:
Step
SEPED303004EN 01/2013
Action
Select the section from which you wish to delete the execution condition.
99
Creating a Program
100
Action
Create a section.
An expansion icon, represented by a white square, appears as illustrated
below:
SEPED303004EN 01/2013
Creating a Program
Step
3
SEPED303004EN 01/2013
Action
Click on the section expansion icon.
The section content is reduced.
You can tell the section has been reduced when a "+" sign is visible in the
section expansion icon, as illustrated below:
101
Creating a Program
Functionality
The sections and sub-sections define a tree structure with three levels.
The hierarchical level of a section is indicated by means of automatic numbering in
the section header and end.
The tree structure levels are available in the grayed-out part above the first program
line in the form of three numbered icons. They are used to control the expansion or
reduction of sections.
Defining a Section Tree Structure
To display the section levels in a program, proceed as follows:
Step
102
Action
Define a section.
The first level of the section tree structure appears in the header.
SEPED303004EN 01/2013
Creating a Program
Action
In the above example, the level 1 sections include a level 2 section, and two
sections of level 2 and 3 respectively.
You can only pass from one tree structure level to another if the higher (or
lower) level of the relevant section level has been expanded (or reduced).
SEPED303004EN 01/2013
103
Creating a Program
Action
Deleting a Comment
To delete a comment line, proceed as follows:
Step
104
Action
Click on Edit Delete, or right-click on the line, then select the Delete option,
or use the <Del> key on your keyboard.
SEPED303004EN 01/2013
Creating a Program
Copy/Paste Function
Introduction
You can perform copy/paste operations on the cells, lines or even sections of a
program.
NOTE: The MS Windows keyboard shortcuts <Ctrl> + C (to copy) and <Ctrl> + V
(to paste) are also available.
Copying/Pasting Cells
It is possible to copy/paste cells, or a selection of cells. The content of copied cells
overwrites the content of the cells into which the data is pasted.
Copy/paste cell operations are performed in the same zone: from contact to contact
and coil to coil.
When copying a selection of linked cells, you must take account of the size of the
selection and the type of instructions they contain. A selection of 3 cells on 3 lines
cannot be copied from column 9, for example.
If a mistake is made, Logipam issues the following messages:
Procedure
To copy and/or paste a variable of the same type, proceed as follows:
Step
SEPED303004EN 01/2013
Action
In the program, select a cell containing, for example, the memorized bit MS005.
105
Creating a Program
Step
5
Action
Click on Edit Paste.
The resource, MS005, is displayed in the cell.
You can also right-click on the resource MS005, then select the Copy option
then Paste.
Copying/Pasting Lines
It is possible to copy/paste a line, or a selection of lines. The content of the copied
line is inserted before the line where the data is pasted.
To copy/paste lines, make sure that the maximum number of lines does not exceed
the 1400 lines allowed in a program.
If a mistake is made, Logipam issues the following messages:
Procedure
To copy and/or paste lines, proceed as follows:
Step
Action
Copying/Pasting Sections
It is possible to copy/paste a section, or a selection of sections, or a selection of lines
and sections. The content of the copied selection is inserted before the line where
the data is pasted.
To copy/paste sections, make sure that the maximum number of sections does not
exceed the 100 sections allowed and that the section nesting level does not exceed
the 3 levels allowed.
106
SEPED303004EN 01/2013
Creating a Program
Procedure
To copy and/or paste sections, proceed as follows:
Step
SEPED303004EN 01/2013
Action
In the program, select one or more sections. Note: If the section has been
reduced, expand it so that you are sure of the nesting level and the number of
lines.
Point to another section: either after a section if you wish to insert the selected
section(s), or selecting the section(s) you wish to overwrite.
107
Creating a Program
Search/Replace Function
Introduction
You can search for occurrences of a variable or object in a program and replace
them.
Searching for a Variable
To search for occurrences of a variable or an object, proceed as follows:
Step
108
Action
SEPED303004EN 01/2013
Creating a Program
Replacing a Variable
To replace one variable with another, proceed as follows:
Step
Description
Select the variable to be modified in the program (I104, for example). The
selected variable cell turns yellow.
Select Edit Replace to access the replace window or use the contextual
menu.
The Replace window opens.
Select the variable you wish to replace the variable that has been selected
(I204, for example).
The replacement to be made is indicated under the dialog box title. In the
illustration, variable I104 that has already been selected in the program is to be
replaced with variable I204.
3
SEPED303004EN 01/2013
109
Creating a Program
Action
Create two elements in the program; for example, internal bits MS006 and
MX006 in the contact 2 and 4 columns of line 3.
Position the mouse cursor between the two elements, i.e. in the cell at the
intersection of line 3 and column 3, on the dotted line.
Deleting a Connection
To delete a connection between two variables, proceed as follows:
Step
110
Action
Select a connection; for example, the solid line of the horizontal connection
created on line 3 of the contact 3 column.
SEPED303004EN 01/2013
Creating a Program
Action
Displaying by Name
To display variables by their name, proceed as follows:
Step
SEPED303004EN 01/2013
Action
111
Creating a Program
112
SEPED303004EN 01/2013
Creating a Program
Saving a Program
Introduction
To save a program, use:
The Save option to save a program that has already been saved.
The Save as option to save a new program or to save a program with another
name.
Description
When saving a programming project, Logipam creates:
SEPED303004EN 01/2013
113
Creating a Program
Clicking on this button or using the List of inconsistencies option of the Display
menu accesses the data entry error report.
You can switch to Simulation mode without correcting the errors. However, it is
advisable to run this check and to correct the errors to avoid any problem during
simulation.
114
SEPED303004EN 01/2013
Creating a Program
Action
Select Display List of inconsistencies to start program validation or click
on the following icon which can be found on the toolbar:
SEPED303004EN 01/2013
In the window, double-click on the line with the error. Logipam goes directly to
the zone containing the error in the program.
115
Creating a Program
116
Message
Description
No day selected
SEPED303004EN 01/2013
Creating a Program
Program Checking
Introduction
When switching to Simulation mode or exporting to SFT2841, Logipam generates
the executable program and checks the program, to ensure that it does not contain
any errors.
The result of this checking can also be viewed at any time using the Report option
of the Display menu.
Accessing the Report
To access the report, proceed as follows:
Step
1
Action
Select Display Report.
The Report window opens.
SEPED303004EN 01/2013
To correct the errors, double-click on the line with the error. Logipam goes
directly to the zone containing the error in the program.
117
Creating a Program
Message
Description
Error
Invalid file
Connection error
Warning
Information
118
SEPED303004EN 01/2013
Creating a Program
SEPED303004EN 01/2013
119
Creating a Program
120
Action
SEPED303004EN 01/2013
Creating a Program
SEPED303004EN 01/2013
121
Creating a Program
122
SEPED303004EN 01/2013
Logipam
Simulating a Program
SEPED303004EN 01/2013
Simulating a Program
6
Scope of This Chapter
This chapter describes how simulation works and the operations to be performed to
simulate a program.
What Is in This Chapter?
This chapter contains the following topics:
Topic
SEPED303004EN 01/2013
Page
124
Executing Simulation
125
126
129
123
Simulating a Program
124
SEPED303004EN 01/2013
Simulating a Program
Executing Simulation
Introduction
The operations for executing simulation are as follows:
Each function can be activated from an icon in the toolbar. For more information on
the simulation mode toolbar, see Familiarization With the Software, page 59.
Displaying States and Behaviors
During simulation, the screen display is automatically refreshed so that it constantly
reflects the state of the variables and objects.
During simulation, the contacts, coils and connections take on the following colors:
The name of the variables and objects takes the following colors:
Performing Simulation
Switching to simulation mode automatically places the simulator in Stop state and
initializes simulation.
Run starts simulation in continuous mode. Execution in continuous mode
corresponds to successive execution of several simulation steps.
Stop interrupts simulation immediately, this state can only be exited with the aid of
the Run command.
When simulation is in Run mode, you must stop it using the Stop button before
initializing the variables.
Execution of one simulation step corresponds to actual execution of one Sepam cycle.
Exiting simulation mode causes simulation to stop automatically.
SEPED303004EN 01/2013
125
Simulating a Program
The window opens. By default this window is empty, and you have to select the
variables you wish to modify.
The Status of variables window looks like this:
126
SEPED303004EN 01/2013
Simulating a Program
For variables
Double-click on the status value to change it to the opposite status.
Double-click on the variable in the No., Name or Category column to open the
corresponding parameter-setting window.
For objects:
Double-click on the current value of the object to modify it.
Double-click on the object in the No., Name or Category column to open the
corresponding parameter-setting window.
SEPED303004EN 01/2013
Ref. No.
Description
If you launch an execution step, the current flows and the whole contact turns
red.
127
Simulating a Program
The example below illustrates the change of status from 0 to 1 then back to 0.
128
Ref. No.
Description
SEPED303004EN 01/2013
Simulating a Program
Current time
The current time is the present value of the simulation clock, which can be
modified during simulation or with the simulation stopped.
Time at initialization
The time at initialization is the value that the current time takes on initialization,
which can only be modified with the simulation stopped.
You need to set the simulation initialization time. This information is saved and then
positioned each time simulation is initialized.
Simulation Time Operation
The simulation day and time change as follows:
The time display format shows the day of the week, hour, minute, second and
millisecond.
A week starts on Monday at 00h00m00s000ms and ends on Sunday at
23h59m59s999ms and continues cyclically.
The time changes according to the simulation execution; if the simulation executes
40 Sepam cycles of 14 ms, the time changes by 560 ms.
The initial simulation time is set by default at Monday 00h00h00s000ms. The
simulation time only acts as a reference for clocks that send their pulse on defined
days and at defined times.
The simulation time does not affect the timers; the latter base their behavior on the
simulation execution.
SEPED303004EN 01/2013
129
Simulating a Program
130
Action
SEPED303004EN 01/2013
Logipam
Operating a Program
SEPED303004EN 01/2013
Operating a Program
7
Scope of This Chapter
This chapter describes all the operations involved in loading a Logipam program into
Sepam, operating and maintaining it.
What Is in This Chapter?
This chapter contains the following topics:
Topic
SEPED303004EN 01/2013
Page
132
134
136
143
145
131
Operating a Program
132
SEPED303004EN 01/2013
Operating a Program
Procedure
To export a project, proceed as follows:
Step
1
Action
Select Execution Export for SFT2841.
If the program contains no errors: the export occurs automatically and the
xxxx.bin program file is created in the C:\Program
Files\SCHNEIDER\SFT2841\Logipam directory.
If the program contains errors: the Report window opens to indicate the
errors, as illustrated in the figure below:
To correct the errors, double-click on the line with the error. Logipam goes
directly to the zone in the diagram containing the error.
When the errors are corrected, Logipam goes ahead with exporting the file.
The xxxx.bin program file is created in the C:\Program
Files\SCHNEIDER\SFT2841\Logipam directory.
SEPED303004EN 01/2013
133
Operating a Program
The information provided in this document relates only to the use of Logipam
programs in SFT2841 with a view to their setup. For more information on the
functions of SFT2841, see the documentation for the SFT2841 software.
Configuring Sepam and a Logipam Program
Sepam is configured with its new Logipam program in connected or disconnected
mode with SFT2841.
The steps involved in setup are as follows:
The Logipam file and the SFT2841 parameters and protection settings file are
available.
SFT2841 is connected to Sepam.
The displayed state of all the internal variables is then used to check execution of
the program.
134
SEPED303004EN 01/2013
Operating a Program
Counters
It is possible to view the current value of the counters.
Configuration bits
It is possible to display their state and toggle them.
For more information on the operation of Sepam, see the Sepam series 80
documentation.
SEPED303004EN 01/2013
135
Operating a Program
Description
Action
SEPED303004EN 01/2013
Operating a Program
137
Operating a Program
Action
Program Activity
To turn on the selected program and make it active, click on the On button in the
Activity zone.
To turn off the selected program and make it inactive, click on the Off button in the
Activity zone.
Setting Variables
The SFT2841 can be used to view internal bits and programmed objects and to set
them. To do this, select the corresponding tab.
Each tab displays the current value of the parameters initialized with the default
value contained in the program during selection. The default value is the one chosen
when configuring the program on the SFT2885.
138
SEPED303004EN 01/2013
Operating a Program
SEPED303004EN 01/2013
139
Operating a Program
Setting Counters
The Counters tab is used to display the counters used by the program and to set
their parameters if necessary.
Only the set point can be modified by double-clicking on it. It must however remain
within the range [0-65535].
Apply the modifications before going to the next settings.
140
SEPED303004EN 01/2013
Operating a Program
Setting Clocks
The Clocks tab is used to display the clocks used by the program and to set their
parameters if necessary.
You can adjust the clock setting by clicking in the boxes relating to the days or by
entering a value in the fields reserved for times, pulses and periods.
Apply the modifications before going to the next settings.
SEPED303004EN 01/2013
141
Operating a Program
Setting Timers
The Timers tab is used to display the timers used by the program and to set their
parameters if necessary.
Only the duration can be modified by double-clicking on it. It must however remain
within the defined range.
Apply the modifications before going to the next settings.
142
SEPED303004EN 01/2013
Operating a Program
NOTE: The Logipam button is only available if the Logipam program has been
configured, otherwise the Equations button appears for logic equations.
By default, the matrix displays all the possible assignments.
SEPED303004EN 01/2013
143
Operating a Program
144
SEPED303004EN 01/2013
Operating a Program
SEPED303004EN 01/2013
145
Operating a Program
146
SEPED303004EN 01/2013
Logipam
SEPED303004EN 01/2013
Appendices
SEPED303004EN 01/2013
147
148
SEPED303004EN 01/2013
Logipam
Appendices
SEPED303004EN 01/2013
Appendices
A
Scope of This Chapter
This chapter lists the predefined variables, grouped by function, and the keyboard
shortcuts.
What Is in This Chapter?
This chapter contains the following topics:
Topic
SEPED303004EN 01/2013
Page
150
154
156
159
Keyboard Shortcuts
164
149
Appendices
Description
Name
Identifier
Latching acknowledgement
Alarm
Genset shutdown
Automatic transfer
150
V_RESET_ORD
SI068
SI074
V_CLEAR_ORD
SI069
SI075
SI035
V_SHUTDN_ORD
V_SHUTDN_ON
SI082
V_TIESYNCFAIL
SI053
V_AT_TRIPPING
SI054
Tripping order given via 2/3, 1/2 logic Automatic transfer output
V_2/3_TRIPPING
SI055
V_CLOSE_EN
SI056
V_CLOSE_NO_ORD
SI057
V_TIE_CLOSE_EN
SI058
V_TIE_CLOSING
SI059
V_TIE_OPENING
SI060
V_TRANSF_ON
SI086
SEPED303004EN 01/2013
Appendices
Function
Description
Name
Identifier
Switchgear control
V_TRIPPED
SI017
V_CLOSED
SI018
V_CLOSE_INHIBITED
SI019
SI020
V_SYNC_INPROC
SI039
V_NOSYNC_DU
SI040
V_NOSYNC_DPHI
SI041
V_NOSYNC_DF
SI042
V_SYNC_STOP
SI043
V_SWCTRL_ON
SI078
Synchro-check enabled
V_SYNC_ON
SI079
V_NOSYNC
SI089
V_SYNC_OK
SI090
V_STP1_TRIPPING to
V_STP4_TRIPPING
SI044 to
SI047
V_STP1_CTRLFLT to
V_STP4_CTRLFLT
SI048 to
SI051
V_STP1_CLOSING to
V_STP4_CLOSING
SI091 to
SI094
V_BANK_ON
SI080
Communication
V_REM_SETTING
SI066
V_REVERSEPHASE
SI098
Load shedding
SI034
V_LOADSH_ON
SI084
De-excitation
V_DE-EXCIT_ORD
SI036
De-excitation enabled
V_DE-EXICT_ON
SI083
SEPED303004EN 01/2013
V_LOADSH_ORD
SI023
151
Appendices
Function
Description
Name
Identifier
TC/switchgear position
discrepancy
V_TC/CBDISCR
SI021
Data log
V_DLG_ACTIVED
SI104
Power factor
V_PFACTOR
SI076
V_PFACTOR_SIGN
SI077
Mimic-based UMI
V_MIMIC_OUT_1 to
V_MIMIC_OUT_16
SI001 to
SI016
V_MIMIC_LOCA
SI070
Temperature measurement
Disturbance recording
Protections
Restart
SI071
V_MIMIC_TEST
SI072
V_RTD2FAULT
SI025
V_RTD2FAULT
SI026
V_OPG_TRIGGED
SI097
V_OPG_ON
SI087
V_OPG_INHIBITED
SI033
Pick-up
V_PICKUP
SI027
V_PICKUP_OC
SI028
Drop-out
V_DROPOUT
SI029
V_RESTARTING
SI052
Restart enabled
V_RESTART_ON
SI085
V_MSR_TRIGGED
SI103
Logic discrimination
V_LOGDSC_BL1 to
V_LOGDSC_BL2
SI030 to
SI031
152
V_LOGDSC_TRIP
Tripping command given by logic
discrimination - Logic discrimination function
output
SI032
V_LOGDSC_ON
SI081
V_PHASE_DIR
SI099
V_PHASE_INV
SI100
SI101
V_PHASE_ACTIVE
SI102
V_VAUX_LOW
SI037
V_VAUX_HIGH
SI038
V_VAUX_ON
SI067
SEPED303004EN 01/2013
Appendices
Function
Name
Identifier
V_MAXBRKCUR
SI024
V_CCS
SI095
V_TCS
SI096
Open/close order
supervision
V_CTRLFAULT
SI022
System
V_INIT
SI061
V_ADJUST
SI062
V_PARTIALFAULT
SI063
Group A enabled
V_GROUPA
SI064
Group B enabled
V_GROUPB
SI065
V_ONEMINUT
SI073
V_SFT2841
SI088
SEPED303004EN 01/2013
Description
153
Appendices
Comments
Name
Identifier
V_RESET
SO045
V_INHIB_RESET_LOCAL
SO047
Alarm
V_CLEAR
SO046
Genset shutdown
V_SHUTDOWN
SO048
Automatic transfer
V_TRANS_ON_FLT
SO059
SO060
V_TRANS_V_EN
SO077
V_TRIPCB
SO042
V_CLOSECB
SO043
V_INHIBCLOSE
SO044
V_CLOSE_NOCTR
SO050
V_CLOSE_STP1 to
V_CLOSE_STP4
SO055 to
SO058
V_TRIP_STP1 to
V_TRIP_STP4
SO051 to
SO054
De-excitation
V_DE-EXCITATION
SO049
V_DLG_START
SO079
Mimic-based UMI
V_MIMIC_IN_1 to
V_MIMIC_IN_16
SO061 to
SO076
V_RST_CURRENTS
SO005
V_RST_POWERS
SO006
Switchgear control
154
SEPED303004EN 01/2013
Appendices
Function
Comments
Name
Identifier
Disturbance recording
V_OPG_INHIBIT
SO004
V_OPG_VALID
SO001
V_OPG_MANUAL
SO002
SO007 to
SO020
SO041
V_MSR_START
SO078
Thermal overload
protection (49RMS)
V_RST_THERMAL
SO003
SEPED303004EN 01/2013
155
Appendices
156
Protection
Identifier
Associated Information
12
P12_X_101
P12_X_113
1 to 2
Reset
Inhibition
14
P14_X_101
P14_X_113
1 to 2
Reset
Inhibition
21B
P21B_1_101
P21B_1_113
24
P24_X_101
P24_X_113
1 to 2
Reset
Inhibition
27
P27_X_101
P27_X_113
1 to 4
Reset
Inhibition
27D
P27D_X_101
P27D_X_103
1 to 2
Reset
Inhibition
27R
P27R_X_101
P27R_X_103
1 to 2
Reset
Inhibition
27TN/64G2
P27TN/64G2_X_101
P27TN/64G2_X_113
1 to 2
Reset
Inhibition
32P
P32P_X_101
P32P_X_113
1 to 2
Reset
Inhibition
32Q
P32Q_1_101
P32Q_1_113
Reset
Inhibition
37
P37_1_101
P37_1_113
Reset
Inhibition
37P
P37P_X_101
P37P_X_113
1 to 2
Reset
Inhibition
38/49T
P38/49T_X_101
P38/49T_X_113
1 to 16
Reset
Inhibition
40
P40_1_101
P40_1_113
46
P46_X_101
P46_X_113
1 to 2
Reset
Inhibition
47
P47_X_101
P47_X_113
1 to 2
Reset
Inhibition
48/51LR
P48/51LR_1_101
P48/51LR_1_102
P48/51LR_1_113
Reset
Inhibition
Reset
Inhibition
Reset
Motor re-acceleration
Inhibition
SEPED303004EN 01/2013
Appendices
SEPED303004EN 01/2013
Protection
Identifier
49RMS
P49RMS_1_101
P49RMS_1_113
Reset
Inhibition
50/27
P50/27_1_101
P50/27_1_113
Reset
Inhibition
50/51
P50/51_X_101
P50/51_X_113
50BF
P50BF_1_101
P50BF_1_107
P50BF_1_113
P50BF_1_119
50N/51N
P50N/51N_X_101
P50N/51N_X_113
1 to 8
Reset
Inhibition
51C
P51C_X_101
P51C_X_113
1 to 8
Reset
Inhibition
50V/51V
P50V/51V_X_101
P50V/51V_X_113
1 to 2
Reset
Inhibition
59
P59_X_101
P59_X_113
1 to 4
Reset
Inhibition
59N
P59N_X_101
P59N_X_113
1 to 2
Reset
Inhibition
64REF
P64REF_X_101
P64REF_X_113
1 to 2
Reset
Inhibition
66
P66_1_101
P66_1_102
P66_1_113
67
P67_X_101
P67_X_113
1 to 2
Reset
Inhibition
67N
P67N_X_101
P67N_X_113
1 to 2
Reset
Inhibition
78PS
P78PS_1_101
P78PS_1_113
Reset
Inhibition
79
P79_1_113
Inhibition
81H
P81H_X_101
P81H_X_113
1 to 2
Reset
Inhibition
81L
P81L_X_101
P81L_X_113
1 to 4
Reset
Inhibition
81R
P81R_X_101
P81R_X_113
1 to 2
Reset
Inhibition
87M
P87M_1_101
P87M_1_113
1 to 8
Associated Information
Reset
Inhibition
Reset
Start 50BF
Inhibition
Circuit breaker closed
Reset
Motor re-acceleration
Inhibition
Reset
Inhibition
157
Appendices
158
Protection
Identifier
Associated Information
87T
P87T_1_101
P87T_1_113
P87T_1_118
CTS
PCTS_X_113
1 to 2
Inhibition
VTS
PVTS_X_101
PVTS_X_103
PVTS_X_113
PVTS_X_117
1 to 2
Reset
Phase VT fault
Inhibition
Voltage presence
Reset
Inhibition
Restraint on closing
SEPED303004EN 01/2013
Appendices
SEPED303004EN 01/2013
Protection
Identifier
Associated Information
12
P12_X_1
P12_X_3
P12_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
14
P14_X_1
P14_X_3
P14_X_16
P14_X_36
1 to 2
Pick-up
Protection output
Protection inhibited
Zero speed
21B
P21B_1_1
P21B_1_3
P21B_1_16
24
P24_X_1
P24_X_3
P24_X_16
25
P25_1_46
P25_1_47
P25_1_49
P25_1_50
P25_1_51
P25_1_52
P25_1_53
27
P27_X_1
P27_X_3
P27_X_7
P27_X_8
P27_X_9
P27_X_16
P27_X_23
P27_X_24
P27_X_25
P27_X_26
P27_X_27
P27_X_28
1 to 4
Pick-up
Protection output
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
Phase 1 instantaneous
Phase 2 instantaneous
Phase 3 instantaneous
Phase 1 delayed
Phase 2 delayed
Phase 3 delayed
27D
P27D_1_1
P27D_1_3
P27D_1_16
1 to 2
Pick-up
Protection output
Protection inhibited
27R
P27R_1_1
P27R_1_3
P27R_1_16
1 to 2
Pick-up
Protection output
Protection inhibited
Pick-up
Protection output
Protection inhibited
1 to 2
Pick-up
Protection output
Protection inhibited
Synchro-check
No voltage check
Phase difference check
Frequency difference check
Voltage difference check
No Usync1
No Usync2
159
Appendices
Protection
160
Identifier
Associated Information
27TN/64G2 P27TN/64G2_X_3
P27TN/64G2_X_16
P27TN/64G2_X_23
1 to 2
Protection output
Protection inhibited
Instantaneous
32P
P32P_X_1
P32P_X_3
P32P_X_16
P32P_X_19
P32P_X_20
1 to 2
Pick-up
Protection output
Protection inhibited
Positive reactive power
Negative reactive power
32Q
P32Q_1_1
P32Q_1_3
P32Q_1_16
P32Q_1_54
P32Q_1_55
Pick-up
Protection output
Protection inhibited
Positive reactive power
Negative reactive power
37
P37_1_1
P37_1_3
P37_1_16
Pick-up
Protection output
Protection inhibited
37P
P37P_1_1
P37P_1_3
P37P_1_16
1 to 2
Pick-up
Protection output
Protection inhibited
38/49T
P38/49T_X_3
P38/49T_X_10
P38/49T_X_12
P38/49T_X_16
1 to 16
Protection output
Alarm
RTD fault
Protection inhibited
40
P40_1_1
P40_1_3
P40_1_16
P40_1_23
46
P46_X_1
P46_X_3
P46_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
47
P47_X_1
P47_X_3
P47_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
48/51LR
P48/51LR_1_3
P48/51LR_1_13
P48/51LR_1_14
P48/51LR_1_15
P48/51LR_1_16
P48/51LR_1_22
Pick-up
Protection output
Protection inhibited
Circle 1
Protection output
Locked rotor
Excessive starting time
Locked rotor on start
Protection inhibited
Starting in progress
SEPED303004EN 01/2013
Appendices
SEPED303004EN 01/2013
Protection
Identifier
49RMS
P49RMS_1_3
P49RMS_1_10
P49RMS_1_11
P49RMS_1_16
P49RMS_1_18
P49RMS_1_22
P49RMS_1_38
Protection output
Alarm
Inhibit closing
Protection inhibited
Hot state
Inhibit thermal overload
Zero rotor speed
50/27
P50/27_1_1
P50/27_1_16
P50/27_1_35
Protection output
Protection inhibited
50-27 protection ready
50/51
P50/51_X_1
P50/51_X_3
P50/51_X_4
P50/51_X_7
P50/51_X_8
P50/51_X_9
P50/51_X_16
50BF
P50BF_1_1
P50BF_1_3
P50BF_1_16
50N/51N
P50N/51N_X_1
P50N/51N_X_3
P50N/51N_X_4
P50N/51N_X_16
P50N/51N_3_56
1 to 8
Pick-up
Protection output
Drop-out
Protection inhibited
15 A set point
51C
P51C_X_1
P51C_X_3
P51C_X_16
1 to 8
Pick-up
Protection output
Protection inhibited
50V/51V
P50V/51V_X_1
P50V/51V_X_3
P50V/51V_X_4
P50V/51V_X_7
P50V/51V_X_8
P50V/51V_X_9
P50V/51V_X_16
1 to 2
Pick-up
Protection output
Drop-out
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
1 to 8
Associated Information
Pick-up
Protection output
Drop-out
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
Pick-up
Protection output
Protection inhibited
161
Appendices
162
Protection
Identifier
Associated Information
59
P59_X_1
P59_X_3
P59_X_7
P59_X_8
P59_X_9
P59_X_16
P59_X_23
P59_X_24
P59_X_25
P59_X_26
P59_X_27
P59_X_28
1 to 4
Pick-up
Protection output
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
Phase 1 instantaneous
Phase 2 instantaneous
Phase 3 instantaneous
Phase 1 delayed
Phase 2 delayed
Phase 3 delayed
59N
P59N_X_1
P59N_X_3
P59N_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
64REF
P64REF_X_1
P64REF_X_3
P64REF_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
66
P66_1_3
P66_1_16
P66_1_29
P66_1_30
P66_1_31
67
P67_X_1
P67_X_3
P67_X_4
P67_X_6
P67_X_7
P67_X_8
P67_X_9
P67_X_16
P67_X_21
P67_X_36
P67_X_37
1 to 2
Pick-up
Protection output
Drop-out
Instantaneous output reverse zone
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
Instantaneous output at 0.8 Is
Delayed 1/3 before latching
Delayed 2/3 before latching
67N
P67N_X_1
P67N_X_3
P67N_X_4
P67N_X_6
P67N_X_16
P67N_X_21
1 to 2
Pick-up
Protection output
Drop-out
Instantaneous output reverse zone
Protection inhibited
Instantaneous output at 0.8 Is0
78PS
P78PS_1_1
P78PS_1_3
P78PS_1_16
Protection output
Protection inhibited
Stop/start inhibit
Startup total reached
Consecutive startups reached
Pick-up
Protection output
Protection inhibited
SEPED303004EN 01/2013
Appendices
SEPED303004EN 01/2013
Protection
Identifier
Associated Information
79
P79_1_201
P79_1_202
P79_1_203
P79_1_204
P79_1_205
P79_1_211
P79_1_212
P79_1_213
P79_1_214
81H
P81H_X_1
P81H_X_3
P81H_X_16
1 to 2
Pick-up
Protection output
Protection inhibited
81L
P81L_X_1
P81L_X_3
P81L_X_16
1 to 4
Pick-up
Protection output
Protection inhibited
81R
P81R_X_1
P81R_X_3
P81R_X_16
P81R_X_42
P81R_X_43
P81R_X_44
P81R_X_45
1 to 2
Pick-up
Protection output
Protection inhibited
Voltage invalid
Frequency invalid
Positive rate of change
Negative rate of change
87M
P87M_1_3
P87M_1_7
P87M_1_8
P87M_1_9
P87M_1_16
P87M_1_33
P87M_1_34
P87M_1_39
Protection output
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
High threshold
Threshold %
Sensor loss
87T
P87T_1_3
P87T_1_16
P87T_1_33
P87T_1_34
P87T_1_39
P87T_1_41
Protection output
Protection inhibited
High threshold
Percentage-based set point
Sensor loss
Test mode
CTS
PCTS_X_3
PCTS_X_7
PCTS_X_8
PCTS_X_9
PCTS_X_16
1 to 2
Protection output
Phase 1 fault
Phase 2 fault
Phase 3 fault
Protection inhibited
VTS
PVTS_X_3
PVTS_X_16
1 to 2
Protection output
Protection inhibited
Recloser in service
Recloser ready
Recloser successful
Permanent trip
Closing by reclosing indication
Recloser cycle 1
Recloser cycle 2
Recloser cycle 3
Recloser cycle 4
163
Appendices
Keyboard Shortcuts
Navigation Shortcuts in a Diagram
The navigation shortcuts available in a Logipam diagram are as follows:
Task
Keyboard shortcut
Ctrl+N
Ctrl+O
Save a diagram
Ctrl+S
Print a diagram
Ctrl+P
164
Task
Keyboard shortcut
Ctrl+X
Ctrl+C
Ctrl+V
Del
Ctrl+A
F3
Ctrl+F3
Ctrl+H
SEPED303004EN 01/2013