Professional Documents
Culture Documents
Power Steering
Power Steering
Electric Power Steering (EPS) provides power assist even when the
engine is stopped. It also improves fuel economy because it is
lightweight and the DC motor consumes energy only when power assist
is required. The EPS is powered by a 12V motor and is not dependent
on the engine for its power source so steering feel is not affected when
the engine is shut OFF.
The EPS ECU uses the torque sensor output and information from the
Skid Control ECU about vehicle speed and torque assist demand to
determine the direction and force of the power assist. It then actuates
the DC motor accordingly.
Figure 7.1
T072f701c
7-1
Section 7
Steering Gear
DC Motor The DC motor uses a worm gear to transmit the motors torque to the
column shaft.
Reduction The reduction mechanism transmits motor power assist to the pinion
Mechanism shaft. The reduction mechanism consists of the ring gear that is
secured to the pinion shaft and the pinion gear that is integrated with
the motor shaft. The power assist of the motor is transmitted by the
reduction mechanism to the pinion shaft which provides power assist
to the steering effort.
Torque Sensor The torque sensor detects the twist of the torsion bar and converts the
applied torque into an electrical signal. The EPS ECU uses that signal
to calculate the amount of power assist the DC motor should provide.
(04 & later Prius) The 04 & later Prius uses an inductiontype torque sensor. Detection
Ring 1 and 2 are mounted on the input shaft and Detection Ring 3 is
mounted on the output shaft. When torque is applied to the torsion bar
the detection rings move in relationship to each other. The detection
coil senses a change in inductance that is proportional to the amount of
torque applied.
EPS CPU
The EPS ECU receives signals from various sensors, judges the current
vehicle condition and determines the assist current to be applied to the
DC motor.
Fail Safe If the EPS ECU detects a malfunction in the EPS system a warning
light illuminates to alert the driver. The EPS ECU will store the
DTC(s) and the system will power down, however, the system still
provides the ability to steer manually.
7-2
EPS Steering
System
Figure 7.2
T072f702c
Figure 7.3
T072f703c
Figure 7.4
T072f704c
Torque Sensor
01 - 03 Prius
Torque Sensor
04 & later Prius
7-3
Section 7
Calibration of
Torque Sensor
Zero Point
DTC C1515/15
Torque Sensor
Zero Point
Calibration Not
Performed
DTC C1515 does not indicate a problem. This DTC is set when the
Torque Sensor Zero Point calibration is not performed. Calibrate the
Torque Sensor Zero Point and then delete the DTC.
DTC C1515/15
Torque Sensor
Zero Point
Incomplete
DTC C1516 also does not indicate a problem. It is set when the Torque
Sensor Zero Point calibration is not completed normally. Try the
procedure again and delete the DTC when finished.
DTC C1524/24
Motor Circuit
Malfunction
DTC U0073 and U0121 set when there is a problem in the CAN
communication circuit. DTC U0121 indicates a communication fault
with the skid control ECU, while U0073 indicates a general
malfunction of the CAN communication system.
Intermittent EPS
Malfunctions
7-4
Intermittent EPS
Records
Figure 7.5
T072f705c
7-5
Section 7
Figure 7.6
T072f706
There may be cases where customers complain that the steering is too
sensitive. This is usually a normal condition. To check the EPS system
using the Diagnostic Tester, go to the EPS Data List. Always check
the Motor Actual amperage and the Torque voltage. Refer to the EPS
section of the Repair Manual specifications. The screen print above
shows normal conditions with the vehicle ON, and the steering wheel
in the center position.
7-6
WORKSHEET 7-1
Electrical Power Steering
Worksheet Objectives
In this worksheet you will view the EPS Data List and will determine if EPS voltage and amperage values are
normal. You will also become familiar with where to find intermittent problem data and how to perform a Torque
Sensor Adjustment.
Vehicle
Diagnostic Tester
SST 09843-18040
2. In the chart below, fill in the voltages for TRQ1 and TRQ2 while the steering wheel is at center, right and left.
Steering Position
TRQ1
TRQ2
Center
Right
Left
Note: TRQ 3 Is the calculated value of the ECU and is for engineering purposes only. For diagnostic purposes
use TRQ 1 & 2.
3. Are the readings normal? Where did you find the normal readings?
7-7
Section 7
5. Turn the steering wheel to the left lock and then to the right lock. Record the amperage of MOTOR ACTUAL
while turning the steering wheel in each direction.
Turning Left:
Turning Right:
6. Raise the vehicle so that the tires are off the ground.
7. Again turn the steering wheel to left lock and then to right lock. Again record the amperage of MOTOR
ACTUAL while turning the steering wheel in each direction.
Turning Left:
Turning Right:
8. Compare these values with the values you obtained with the wheels on the ground.
9. How can reading the voltage and amperage values help to diagnose the EPS system?
7-8
4. Using the Diagnostic Tester, follow the procedures to complete the ZERO POINT ADJUST.
5. What display on the vehicle now indicates that ZERO POINT ADJUST is complete?
3. When is the Zero Point Adjustment procedure necessary? Return vehicle to normal condition.
7-9
Section 7
7-10