Sample Enodeb Script

//This script provides only an example of eNodeB configuration.
The MML commands

and parameters involved may differ in different LTE versions. For details, see
the MML command reference of the corresponding version.
//An eNodeB is initially configured in minimum configuration mode.
//To turn off the DHCP switch, run the following command:
SET DHCPSW: SWITCH=DISABLE;
//To remove the original default configuration, run the following commands:
RMV RRU: CN=0, SRN=60, SN=0;
RMV RRUCHAIN: RCN=0;
RMV BRD: CN=0, SRN=0, SN=0;
//To configure main devices, run the following commands:
ADD BRD: CN=0, SRN=0, SN=0, BT=USCU;
ADD BRD: CN=0, SRN=0, SN=2, BT=LBBP, WM=RAT_FDD;
ADD BRD: CN=0, SRN=0, SN=16, BT=FAN;
ADD BRD: CN=0, SRN=0, SN=18, BT=UPEU;
ADD RRUCHAIN: RCN=0, TT=CHAIN, HCN=0, HSRN=0, HSN=2, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=LRRU, RXNUM=2, TXNUM=2, R
S=LO, ALMPROCSW=ON;
//To configure ALDs, run the following commands:
ADD RET: DEVICENO=0, DEVICENAME="RET", CTRLCN=0, CTRLSRN=60, CTRLSN=0, RETTYPE=S
INGLE_RET, SCENARIO=REGULAR;
MOD RETSUBUNIT: DEVICENO=0, SUBUNITNO=1, CONNCN1=0, CONNSRN1=60, CONNSN1=0, CONN
PN1=R0A, CONNCN2=0, CONNSRN2=60, CONNSN2=0, CONNPN2=R0B;
MOD RETPORT: CN=0, SRN=60, SN=0, PN=RET_PORT, PWRSWITCH=ON, THRESHOLDTYPE=RET_ON
LY_MULTICORE;
ADD TMA: DEVICENO=1, CTRLCN=0, CTRLSRN=60, CTRLSN=0, SUBUNITNUM=2, CONNCN1=0, CO
NNSRN1=60, CONNSN1=0, CONNPN1=R0A, CONNCN2=0, CONNSRN2=60, CONNSN2=0, CONNPN2=R0
B;
//To configure monitoring units, run the following commands:
ADD FMU: CN=0, MPN=0;
ADD TCU: CN=0, MPN=1;
ADD EMU: MPN=0;
SET ALMPORT: CN=0, SRN=40, SN=0, PN=0, SW=ON, AID=65033, PT=BOOL, AVOL=HIGH;
//To configure power modules, run the following commands:
ADD PMU: CN=0, PTYPE=APM30, MPN=0, LSDF=DISABLE;
ADD PSU: CN=0, SN=1;
ADD BATTERY: CN=0, BTYPE=VRLA_BAT, BC=1000, HTSDF=ENABLE, LVSDF=ENABLE;
//To configure time information, run the following commands:
SET TIMESRC: TIMESRC=NTP;
ADD NTPC: MODE=IPV4, IP="172.166.1.251", SYNCCYCLE=60, AUTHMODE=PLAIN;
SET TZ: ZONET=GMT+0800, DST=NO;
//To configure synchronization information, run the following commands:
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="80.3.101.21", MASK="255.255.2
52.0";
ADD IPCLKLINK: ICPT=PTP, SN=7, CNM=UNICAST, CIP="80.3.101.21", SIP="172.168.49.4
9", PROFILETYPE=1588V2;
SET CLKMODE: MODE=MANUAL, CLKSRC=IPCLK;
//To configure transport resources, run the following commands:
ADD ETHPORT: SN=7, SBT=BASE_BOARD, PA=COPPER, SPEED=AUTO, DUPLEX=AUTO;
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="80.3.101.21", MASK="255.255.2
52.0";
ADD DEVIP: SN=7, SBT=BASE_BOARD, PT=LOOPINT, PN=0, IP="8.10.10.60", MASK="255.25
5.255.255";
5.255.255";
5.255.255";
5.255.255";
5.255.255";
ADD IPRT: SN=7, SBT=BASE_BOARD, DSTIP="0.0.0.0", DSTMASK="0.0.0.0", RTTYPE=NEXTH
OP, NEXTHOP="80.3.101.1";
ADD S1SIGIP: CN=0, SRN=0, SN=7, LOCIP="8.10.10.60", LOCIPSECFLAG=DISABLE, SECLOC
IPSECFLAG=DISABLE, LOCPORT=2910, SWITCHBACKFLAG=ENABLE;
ADD MME: MMEID=0, FIRSTSIGIP="172.169.1.5", FIRSTIPSECFLAG=DISABLE, SECIPSECFLAG
=DISABLE, LOCPORT=2910;
ADD S1SERVIP: CN=0, SRN=0, SN=7, S1SERVIP="8.10.10.61", IPSECFLAG=DISABLE;
MOD ENODEB: ENODEBID=9527, MCC="460", MNC="02";

RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CnOP", CnOperatorType=CNOPERATOR
_PRIMARY, Mcc="460", Mnc="02";
ADD SGW: SGWID=0, SERVIP1="172.169.2.3", SERVIP1IPSECFLAG=DISABLE, SERVIP2IPSECF
LAG=DISABLE, SERVIP3IPSECFLAG=DISABLE, SERVIP4IPSECFLAG=DISABLE;
ADD X2SIGIP: CN=0, SRN=0, SN=7, LOCIP="8.10.10.62", IPSECFLAG=DISABLE, SECIPSECF
LAG=DISABLE, SWITCHBACKFLAG=ENABLE;
ADD X2SERVIP: CN=0, SRN=0, SN=7, X2SERVIP="8.10.10.63", IPSECFLAG=DISABLE;
ADD X2ENODEB: X2ENODEBID=21, FIRSTSIGIP="8.10.10.50", FIRSTIPSECFLAG=DISABLE, SE
CIPSECFLAG=DISABLE, SERVIP1IPSECFLAG=DISABLE, SERVIP2IPSECFLAG=DISABLE, SERVIP3I
PSECFLAG=DISABLE, SERVIP4IPSECFLAG=DISABLE, ENODEBID=1234;
ADD OMCH: IP="8.10.10.65", MASK="255.255.255.255", PEERIP="172.166.1.251", PEERM
ASK="255.255.255.255", BEAR=IPV4, SN=7, SBT=BASE_BOARD, BRT=NO;
ADD VLANMAP: NEXTHOPIP="80.3.101.1", MASK="255.255.248.0", VLANMODE=SINGLEVLAN,
VLANID=3721, SETPRIO=DISABLE;
ADD VLANCLASS: VLANGROUPNO=0, TRAFFIC=USERDATA, SRVPRIO=16, VLANID=3721;
ADD ACL: ACLID=3100;
ADD ACLRULE: ACLID=3100, RULEID=1, PT=IP, SIP="172.169.1.5", SWC="0.0.0.0", DIP=
"8.10.10.60", DWC="0.0.0.7", MDSCP=NO;
ADD PACKETFILTER: SN=7, SBT=BASE_BOARD, PT=ETH, ACLID=3100, MB=DENY;
//To configure security information, run the following commands:
ADD IKEPROPOSAL: PROPID=1, AUTHMETH=IKE_RSA_SIG, DHGRP=DH_GROUP2;
ADD IKEPEER: PEERNAME="ikepeer", PROPID=1, IKEVERSION=IKE_V2, IDTYPE=FQDN, REMOT
EIP="99.9.1.1", REMOTENAME="segw", DPD=PERIODIC;
ADD IPSECPROPOSAL: PROPNAME="ipsecprop", TRANMODE=ESP, ESPAUTHALG=MD5, ESPENCALG
=DES;
ADD ACL: ACLID=3000, ACLDESC="For IPsec";
ADD ACLRULE: ACLID=3000, RULEID=1, PT=IP, SIP="8.10.10.60", SWC="0.0.0.0", DIP="
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
0.0.0.0", DWC="255.255.255.255", MDSCP=NO;
ADD IPSECPOLICY: SPGN="policy", SPSN=1, ACLID=3000, PROPNAME="ipsecprop", PEERNA
ME="ikepeer", LTCFG=LOCAL;
ADD IPSECBIND: SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, SPGN="policy";
ADD ACL: ACLID=3100, ACLDESC="For PacketFilter";
ADD ACLRULE: ACLID=3100, RULEID=1, PT=IP, SIP="172.169.1.5", SWC="0.0.0.0", DIP=
"8.10.10.60", DWC="0.0.0.7", MDSCP=NO;
ADD CERTMK: APPCERT="232_429new.pem";
MOD APPCERT: APPTYPE=IKE, APPCERT="232_429new.pem";
MOD APPCERT: APPTYPE=SSL, APPCERT="232_429new.pem";
ADD TRUSTCERT: CERTNAME="rootcerm.pem";
ADD CROSSCERT: CERTNAME="crosscert.pem";
ADD CA: CANAME="C=CN, O=LTE OG, CN=RANinterim", URL="http://10.108.191.86:8080/p
kix/";
//To configure a sector, run the following command:
ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=1000, LATITUDE=999, SECM=NormalMIMO, ANT
M=2T2R, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=60, SN1=0, PN1=R0A, CN2=0, SRN2=6
0, SN2=0, PN2=R0B, ALTITUDE=300;
//To configure operator information, run the following commands:

MOD ENODEB: ENODEBID=9527, MCC="460", MNC="02";
RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CnOP", CnOperatorType=CNOPERATOR
_PRIMARY, Mcc="460", Mnc="02";
ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=33;
//To configure eRAN sharing, run the following commands:
MOD ENODEBSHARINGMODE: ENodeBSharingMode=SHARED_FREQ;
RST ENODEB:;
ADD CNOPERATOR: CnOperatorId=1, CnOperatorName="CnOp1", CnOperatorType=CNOPERATO
R_SECONDARY, Mcc="460", Mnc="01";
ADD LICENSESHARINGPOLICY: CnOperatorId=0, MaxUserNumRate=50;
ADD LICENSESHARINGPOLICY: CnOperatorId=1, MaxUserNumRate=50;
MOD LICFLOWCTRLALG: UPRATIO=100, TRAFFICSHARETYPE=DEDICATE, OP1TRAFFICRATIO=50,
OP2TRAFFICRATIO=50, OP1TRAFFICSHARRATIO=50, OP2TRAFFICSHARRATIO=50;
ADD CNOPERATORTA: TrackingAreaId=1, CnOperatorId=1, Tac=33;
MOD CELLALGOSWITCH: LocalCellId=0, RanShareModeSwitch=ON;
//To configure a cell, run the following commands:
ADD CELL: LocalCellId=0, CellName="cell0", SectorId=0, FreqBand=7, UlEarfcnCfgIn
d=NOT_CFG, DlEarfcn=2850, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, Ce
llId=100, PhyCellId=100, FddTddInd=CELL_FDD, RootSequenceIdx=0, CustomizedBandWi
dthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG;
ADD CELLOP: LocalCellId=0, TrackingAreaId=0;
ADD CELLOP: LocalCellId=0, TrackingAreaId=1;
ACT CELL: LocalCellId=0;
//To configure neighboring cells, run the following commands:
MOD CELLALGOSWITCH: LocalCellId=0, FreqPriorityHoSwitch=FreqPriorIFHOSwitch-1&Fr
eqPriorIFBlindHOSwitch-1;
MOD ENODEBALGOSWITCH: AnrSwitch=IntraRatEventAnrSwitch-1&IntraRatFastAnrSwitch-1
&IntraRatAnrAutoDelSwitch-1;
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="02", eNodeBId=236, CellId=0, DlEarfcn=31
00, UlEarfcnCfgInd=NOT_CFG, PhyCellId=236, Tac=33;
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="02", eNodeBId=236, CellId=1, DlEarfcn=28
50, UlEarfcnCfgInd=NOT_CFG, PhyCellId=236, Tac=33;
ADD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3100, UlEarfcnCfgInd=NOT_CFG, Cell
ReselPriorityCfgInd=NOT_CFG, SpeedDependSPCfgInd=NOT_CFG, MeasBandWidth=MBW100,
PmaxCfgInd=NOT_CFG, QqualMinCfgInd=NOT_CFG;
ADD EUTRANINTERFREQNCELL: LocalCellId=0, Mcc="460", Mnc="02", eNodeBId=236, Cell
Id=0;
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="02", eNodeBId=236, Cell
Id=1
//To turn on the DHCP switch, run the following command:
SET DHCPSW: SWITCH=ENABLE;

Sample Enodeb Script

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sample Enodeb Script

Uploaded by

Copyright:

Available Formats

//This script provides only an example of eNodeB configuration.

The MML commands

MOD ENODEB: ENODEBID=9527, MCC="460", MNC="02";

//To configure operator information, run the following commands:

You might also like