Professional Documents
Culture Documents
Iso 261 1998 Fastners
Iso 261 1998 Fastners
BS IS0 261:1998
BRITISH STANDARD
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
ICs 21.040.10
National foreword
This British Standard reproduces verbatim IS0 261: 1998 and implements it as the
LJKnaionai standard
The K participation in its preparation was entrusted by Technical Committee
FME/s,Bolts, nuts and accessories, to Subcommittee FME/9/3,Reference standards
Cross-references
The British Standards which implement international or European publications
referred to in this document may be found in the BSI Standards Catalogue under the
section entitled ?InternationalStandardsCorrespondence Index?,or by using the
?Find?faciiity of the BSI Standards Electronic Catalogue.
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards ~ J Xresponsible for their correct application.
?
Summary of pages
This document comprises a front cover, an inside front cover, the IS0 title page,
page ii, pages 1to 5 and a back cover.
AmdNo.
Date
Text affected
O BSI 041999
ISBN O 68032349 8
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy
No reproduction or networking permitted without license from IHS
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
INTERNATIONAL
STANDARD
IS0
261
Second edition
1998-12-15
Reference number
IS0 261:1998(E)
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
Foreword
IS0 (the Intemational Organization for Standardization) is a worldwide federation of national standards bodies (IS0
member bodies). The work of preparing International Standards is normally carried out through IS0 technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnicat
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 YOof the member bodies casting a vote.
International Standard IS0 261 was prepared by Technical Committee ISO/TC 1, Screw threads, Subcommittee
SC 1, Basic data.
This second edition cancels and replaces the first edition (IS0 261:1973) which has been technically revised.
Descriptois:
screw threads,
IS0 metric threads, form specifications, dimensions, diameters, thread pitch, designation.
ii
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
- General plan
1 scope
This International Standard specifies IS0 general purpose metric screw threads (M) having basic profile according
to IS0 68-1. Basic dimensions are given in IS0 724. For tolerances see IS0 965-1.
2 Normative references
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this international Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain
registers of currently valid International Standards.
IS0 68-1:i 998, IS0 general purpose screw threads
is0 965-1:1998, IS0 general putpose metric screw threads - Tolerances-Part 1: Principles and basic data.
iSO 5408:1983, Cylindtical screw threads
- Vocabulary.
3 Definitions
For the purposes of this Intemational Standard, the definitions given in IS0 5408 apply.
4 Designation
A screw thread in conformity with this International Standard shall be designated according to IS0 965-1.
1
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy
No reproduction or networking permitted without license from IHS
~
~
BS IS0 261:1998
5 Choice of diameter and pitch
5.1 Choose, for preference, diameters in column 1 of table 2 and, if necessary, in column 2 and then in column 3.
Diameter 35 mm, and pitch 1,25 mm of diameter 14 mm shall be used only for the special cases indicated in the
footnotes.
Pitches shown in parentheses are to be avoided as far as possible.
5.2 The words "coarse" and 'fine" are given in order to conform to usage. No concept of quality shall, however, be
associated with these words.
it shall be understoodthat the "coarse" pitches are the largest metric pitches used in current practice.
5.3 For the diameter (or the diameter range) selected, choose one of the pitches shown on the corresponding line
(or lines).
5.4 If screw threads finer than those appearing in table 2 are found necessary, only the following pitches shall be
used:
3 mm; 2 mm; 1,5 mm; 1 mm; 0,75 mm; 0,s mm; 0,35 mm; 0,25 mm; 0,2 mm
When selecting such pitches, take into account the fact that there is increasing difficulty in complying with
tolerances as the diameter is increased for a given pitch. It is suggested, that diameters larger than those shown in
table 1 should generally not be used with the pitches indicated.
Table 1
Pitch
O, 5
22
0.75
33
80
1.5
150
200
300
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
2
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy
No reproduction or networking permitted without license from IHS
BS IS0 261:1998
Table 2
-Nomlnal diameterlpitch
Dimensions in millimetres
Pitch P
Col. 3
3rd choice
coam
fine
1 3
0,25
0.2
02
02
OP2
02
0,2
02
-I
-+
0,25
0,25
3.5
5.5
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
-I
10
12
1
1,25
1,25
1.5
11
1,s
1,75
2
15
2
17
2
2
2
2
2
2S
2,s
23
I
I
3
25
26
27
33
(3)
3s
(3)
32
33
35b
36
2
2
2
2
2
28
38
39
(Kmiinl4ed)
3
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy
No reproduction or networking permitted without license from IHS
BS IS0 261:1998
Table 2 (continued)
Dimensions in millimetres
(continued)
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
~~
BS IS0 261:1998
Table 2 (concluded)
Col. 1
COI. 2
2nd choice
Nominal diameter D, d
~01.3
3rd choice
Pitch P
coarse
fine
8
205
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---
21o
3
3
6
6
215
225
230
235
240
245
8
255
260
265
270
275
5
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy
No reproduction or networking permitted without license from IHS
BS IS0 261:1998
Revisions
British Sta-darsaxe updated by amendment or revision. Users of British Standards
should make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. We
would be grateful if anyone finding an inaccuracy or ambiguity while using this
British Standard would inform the Secretary of the technical committee responsible,
the identity of which can be found on the inside front cover. Tel 0181 996 9000.
Fax:0181 996 7400.
BSI offers members an individual updating service cailed PLUS which ensures that
subscribers automatidy receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standarcis publications should be
addressed to Customer Services. Tel 0181 996 7000. Fax:0181 996 7001.
In response to orders for international standards, it is BSI policy to supply the BSI
implementation of those that have been published as British Standards, unless
otherwise requested
Information on standards
BSI provides a wide range of information on national, European and international
standards through its Library and its Technical Help to Exporters Service. Various
BSI electronic information services are also available which give details on all its
products and services. Contact the Information Centre. Tel 0181 996 7111.
Fax:0181 996 7048.
Subscribing members of BSI are kept up to date with standards developments and
receive substantkd discounts on the purchase price of standards.For details of
these and other benefits contact Membership Aministration. Tel: O181 996 7002.
Fax:0181 996 7001.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright,in the UK, of
the publications of the international standardization bodies. Except as permitted
under the Copynght, Designs and Patents Act 1988 no extract may be reproduced,
stored in a retrieval system or transmitted in any form or by any means - electronic,
photocopying, recording or otherwise - without prior written pennission from BSI.
This does not preclude the free use, in the course of implementing the standard, of
necessary details such as symbols, and size, type or grade designations if these
details are to be used for any other purpose than implementation then the prior
written pennission of BSI must be obtained
If permission is granted, the terms may include royalty payments or a licensing
agreement. Details and advice can be obtained from the Copyright Manager.
Tek 0181 996 7070.
BSI
389 ChiswickHigh Road
London
w4 4AL
--``,,`,,,,````,``,,,``````,``,-`-`,,`,,`,`,,`---