Keshe Power Coils Blueprints Update 8-30-15
Keshe Power Coils Blueprints Update 8-30-15
Lists of Items
1.) Gauge #14 Solid Copper Wire - about 20-30 meters to make 3 sets of MAGRAV COILS
2.) Nano Coating Kit (Refer to Videos of You Tube)
3.) Hand Drill with 2 rods for inner and outer coil forming
or 2 Screw Drivers with different rod diameter that can be inner and outer coils former
4.) Gans Mix for Coating the Coils and putting on the Center Gans Container
5.) Plasma Capacitor - 2-3 Units
6.) A lot of Patience, Prayers and Love in doing your MAGRAV Power Unit
Coils Specfications
1.) All Coiled Counter Clockwise (use the Right Thumb Rule - by pointing your Right Thumb towards you
and curl your 4 fingers to the left going in your palm- The Curl is the Direction of Turn)
2.) Diameter of Loop Coils Varies on tubes use to make the coils.
3.) Magnetical Loop (Outer) consists of 2 coils Magnetical Coil (outer) and Gravitational Coil (inner)
- 140-160 Turns
4.)Gravitational Loop (Inner) consists of 2 coils Magnetical Coil (outer) and Gravitational Coi l(inner)
- 70-80 Turns
Steps
1.) Pray and Make the Coils- 3 sets.
2.) Nano-Coat the Coils using Standard Caustic Method and proper Drying.
3.) Coating the Coils with Gans Mix (Paste/Liquid) and Dry it properly.
4.) Assemble the Coils and Connect properly (make sure to fold the ends of the wires towards itself)
5.) Assemble the casing and properly arrange and stack all parts including the Gans Center Container
6.) Connect the Plasma Capacitor Properly.
7.) Check the Connections again (you can use electrical shrink tape to hold the connections)
8.) Install proper Switches or Breakers to the System
9.) Always consult an Electrical Engineer or Technician when connecting to the Main Power Line
10.) Build another one for your Neighbor and Relatives
Magnetical Coil
(-)
(+)
Gravitational Coil
Extended Wire
from Gravitational Coisl
Gravitational Coil End
Magnetical Coil End
Magnetical Plasma Flow
Gravitational Plasma Flow
Gans Container
Specifications:
Note:
1. Connecting wires must
be nano-coated.
2. Always twist the ends of
the wire back to itself.
(-)
(-)
(+)
(+)
(-)
(+)
Grav Loop =
5 cm
2.5 cm
(+)
1.0 to 1.5 cm
1
2.5 cm
(-)
(+)
(-)
Insulating Tube
(-) (N)
(-) (N)
AC
Power
Grid
LOAD
(+) (L)
(+)
(-)
(+) (L)
Plasma Capacitor
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End
(-) (N)
(-) (N)
AC
Power
Grid
LOAD
(+) (L)
(+)
(-)
(+) (L)
Plasma Capacitor
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End
(-) (N)
(-) (N)
AC
Power
Grid
LOAD
(+) (L)
(+) (L)
(+)
(-)
Plasma Capacitor
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End
(-) (N)
(-) (N)
AC
Power
Grid
LOAD
(+) (L)
(+) (L)
(+)
(-)
Plasma Capacitor
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End
(-)
LOAD
Plasma Capacitor
(-)
(+)
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End
BATTERY
(+)
C1
Power Supply
N
(-)
(+)
(+)
C2
C3
Conventional
Capacitor 2KVAR
C4
Positive Connection
(-)
Negative Connection
Toggle Switch
O
Mechanically Interlocked
Circuit Breaker (Open-Close)
Magrav Coil Set of 3
(Harmonic Filter using
coreless nano-material)
G
Cn
Circuit/ Load
Note:
(+)
(-)
MAGRAV POWER
Power Factor
Corrector Device
MAGRAV POWER (MP) is not an electronic or electrical device that only works
with electron as source of energy. It is a plasma device that uses the energy
from the totality of the atom. Imagine having a tree planted in your backyard.
You have a growing entity with this device. Always send your good intentions
when you deploy your MAGRAV POWER to your electrical system. The
MAGRAV POWER also functions as Power Factor Corrector Device for your
electrical system. With plasma energy provided by the MAGRAV POWER, it
nanocoats your electrical system in your homes and buildings making them
your energy power source.
The MP will have plug-in
systems to access Plasma
Food, Health, Water and
other Plasma systems.
WARNING
Always consult a
Professional Electrician
when connecting to the
Power Grid
MAGRAV POWER
Power Factor
Corrector Device
DOS
1. Contact a Professional
Electrician when connecting to
the Main Breaker.
2. Mount MAGRAV POWER
on Wall or Table Top
3. Connect Proper Polarity
4. Gradually Load the
MAGRAV POWER
5. Allow 3-4 Weeks Use to obtain
maximum potential
6. Keep the MAGRAV POWER in a
place that is out of reach of
children.
7.Send Good Intentions to it.
SAFETY
DONTS
1. DO NOT Wet the MAGRAV
POWER
2. DO NOT Overload,
Maximum 2KW
3. DO NOT invert Polarity
4. DO NOT send negative intentions
to the MAGRAV POWER.
MAGRAV POWER
Power Factor
Corrector Device
SAFETY
MAGRAV POWER
Power Factor
Corrector Device
MP
House KWH
Meter (Single
Phase)
Live
(L) (+)
Breakers
IN
OUT
Electrical
Outlet
Neutral
(N)(-)
Appliances
(Max Total
Load 2.0Kw)
Note: (1) It will take 3-4 weeks for the device to gradually optimize to its
fullest; (2) Add Appliance load gradually in a period of one hour.
MAGRAV POWER
(+)
(-)
(-)
Car
Battery
USB Outlet
MP
(+)
(-)
Car
Plug
USB
Electronic
Devices
MAGRAV POWER
(-)
MP
(-)
(+)
(+)
(-)
Car
Battery
(-)
Starter
Motor
Ground
Connection
Engine
Block
Intake
Manifold
Grounding
Point
Car
Baggage
Lock
Screw
Grounding
Point
Note:
This set up will create a plasma
loop in your engine and car
body. Making your Car Front as
Field EXIT and the Rear as Field
ENTRY