H09344448 PDF
H09344448 PDF
H09344448 PDF
e-ISSN: 2278-2834,p- ISSN: 2278-8735.Volume 9, Issue 3, Ver. IV (May - Jun. 2014), PP 44-48
www.iosrjournals.org
Abstract: Due to large application of induction motor in industries it has become prudent to work on its
efficiency. As the inverter output provides variable voltage magnitude and frequency, with lesser harmonics the
efficiency of induction motor is improved. It is possible only with a better gate pulses. With recent development
in power electronic devices, various PWM techniques have been developed. The most widely used PWM
technique for a 3 phase VSI is SPWM. This paper focuses on step by step development, simulation using
MATLAB/ SIMULINK and also hardware implementation of SPWM pulses.
Keywords: Matlab/ Simulink
I.
Introduction
Alternating current (AC) power can be achieved from direct current (DC) power at desired output
current or voltage and frequency through inversion. Voltage-fed and current-fed are commonly used terms in
inverter circuits. In voltage source inverter (VSI) DC input voltage is normally constant and it is also not
dependent on the load current which is drawn from it. The load voltage is decided by inverter and waveform of
current is determined by the load. Normally machines do not perform smoothly due to large amount of %THD,
which causes noise, vibration and heating in machines. Enough amount of research has been done already in this
area suggesting different techniques for reducing the harmonics in a machine. The purpose of this paper is to
give a detailed design of SPWM techniques for control of inverter gate pulse.
1.1Modulation Technique:
The fundamental idea of the PWM technique is to compare a high frequency wave or signal known as
the carrier signal (a triangular signal with frequency fs) to a signal of low frequency known as the reference
modulating signal ( with frequency fm). The frequency of the reference-modulating signal fm is set the desired
output frequency. In Sinusoidal Pulse width modulation technique for getting the pulses, it is required to
compare sine wave with triangular wave. The carrier - based PWM technique fulfils such a requirement as it
defines the on and off states of the switches of one leg of a VSI by comparing a modulating signal vc (desired ac
output voltage) and a triangular waveform v (carrier signal). In practice, when vc >v the switch S+ is on and
the switch S- is off; similarly, when vc <v the switch S+ is off and the switch S- is on. A special case is when
the modulating signal vc is a sinusoidal at frequency fc and amplitude vc, and the triangular signal v is at
frequency f and amplitude v. This is the sinusoidal PWM (SPWM) scheme. In this case, the modulation
index ma (also known as the amplitude - modulation ratio).
www.iosrjournals.org
44 | Page
II.
Software implementation:
Fig4. 3-phase stator current of SPWM Fig5. FFT analysis with %THD in stator current of SPWM technique.
www.iosrjournals.org
45 | Page
Hardware implementation:
The hardware implementation for the following circuits below is discussed in detail.
Control circuit
Isolation circuit
Driver circuit
Inverter circuit
3.1 Power Supply Circuit
A power supply is a device that supplies electric power to an electrical load. In various parts of the
circuit, 5V and 12V constant value supplies are required.
3.2 Voltage regulator:
The voltage source in a circuit may have fluctuations and would not give the fixed voltage output. The
voltage regulator IC maintains the output voltage at a constant value.
3.3 Control circuit:
SPWM technique is used to generate gate pulses, this is achieved by comparison of a triangle wave
with a reference signal, here a sine wave.
3.3.1 Triangular wave generator:
In case of SPWM technique, the gate pulses for MOSFET is produced by comparing high frequency triangular
carrier wave and the sinusoidal reference wave. Here, we are using op-amp LM318 in order to generate the
triangular wave.The triangular wave generation circuit using LM318 can be obtained by the combination of a
Schmitt trigger and an Integrator.
3.3.2 Comparator:
A comparator is a device that compares two voltages or currents and outputs a digital signal indicating
which is larger. It has two analog input terminals, V+ and V-. It also has one binary digital output Vo. When the
reference wave is greater than the carrier wave the pulse is generated.
3.4 Isolation Circuit
Isolation circuit is used between the control circuit and power circuit as devices in control circuit are
not capable of handling voltages greater than 24V, whereas the power circuit operates at a voltage of around
110V or more. For this purpose an optocoupler is used.
An opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that
transfers electrical signals between two isolated circuits by using commercially available opto-isolators
withstand input-to-output voltages up to 10 KV and voltage
An opto-isolator contains a source of light, almost always a near infrared light-emitting diode (LED),
that converts electrical input signal into light, a closed optical channel, and a photo sensor, which detects
incoming light and either generates electric energy directly, or modulates electric current flowing from an
external power supply. Opto-isolator can transfer the light signal not transfer the electrical signal. The sensor
can be a photo resistor, a photodiode, a phototransistor.
3.5 Driver Circuit
A gate driver is a power amplifier that accepts a low-power input from a controller IC and produces a
high-current drive input for the gate of a high-power transistor such as an IGBT or power MOSFET.
The switching signal for a transistor is usually generated by a logic circuit or a microcontroller, which
provides an output signal that typically is limited to a few mill amperes of current. Consequently, a transistor
which is directly driven by such a signal would switch very slowly, with correspondingly high power loss.
During switching, the gate capacitor of the transistor may draw current so quickly that it causes a current
overdraw in the logic circuit or microcontroller, causing overheating which leads to permanent damage or even
complete destruction of the chip. To prevent this from happening, a gate driver is provided between the
microcontroller output signal and the power transistor.
3.6 Inverter Circuit
A power inverter, or inverter, is an electronic device or circuitry that changes direct current (DC)
to alternating current (AC). A typical power inverter device or circuit will require a relatively stable DC power
source capable of supplying enough current for the intended overall power handling of the inverter.
www.iosrjournals.org
46 | Page
47 | Page
As seen from the above discussion SPWM is superior as compared to pulse width modulation in many aspects
like:
1) The Modulation Index is higher for SPWM as compared to PWM.
2) The output voltage is about 15% more in case of SPWM as compared to PWM.
3) The current and torque harmonics produced are much less in case of PWM.
Hence we see that there is a certain trade off that exists while using SPWM for inverters for Adjustable
speed Drive Operations. Due to this we have to choose carefully as to which of the two techniques to use
weighing the pros and cons of each method.
References
[1].
[2].
[3].
[4].
[5].
[6].
[7].
Prachi S. Dharmadhikari and Gaurav N. Goyal Analysis & Hardware Implementation of Three-Phase Voltage Source
Inverter.
Nazmul Islam Raju, Md. Shahinur Islam, Tausif Ali,Syed Ashraful Karim Study of SPWM Technique & Simulation of Designed
Analog Circuit (Op-Amp) Controlled Three Phase PWM Inverter with Harmonic Reduction.
Zhang Housheng, Zhao Yanlei and Li Haidong Design of Three-phase Intermediate Frequency Aviation Power Based on Single
Chip Microcomputer.
Lin Chengwu,Liu Yan and Sun Bingbin Study On The Technology Of Inverter Based On DSP And SPWM.
Yaow-Ming Chen, Member, IEEE, Chih-Hung Hsieh, and Yuan-Ming Cheng
Modified SPWM Control Schemes for Three-phase Inverters.
Mahesh A. Patel, Ankit Patel, Dhaval R.Vyas and Ketul Patel Use of PWM Techniques for power Quality International
Journal of Recent Trends in Engineering, Vol. 1, No. 4, May 2009
www.iosrjournals.org
48 | Page