Professional Documents
Culture Documents
21h2z31b4 Foxboro
21h2z31b4 Foxboro
inv_foxboro_brand_reg.eps or
inv_infusion_brand_tm.eps or
InvensysLogo_TM.ai
Product Specifications
PSS 21H-2Z31 B4
FBM231 Field Device System Integrator Module, Four Serial Ports,
Redundant
The FBM231 Redundant Field Device System Integrator (FDSI) modules provide a serial interface between
dual-ported field I/O devices and the I/A Series system.
FEATURES
dual-ported devices
control database
Field mounted
of available protocols.
ipath_straight.ai
PSS 21H-2Z31 B4
Page 2
OVERVIEW
A pair of FBM231 modules combine to provide
redundancy at the Fieldbus Module (FBM) level, with
field wiring to two termination assemblies (see
Figure 1). In this configuration, one FBM231 is the
Master, and the other is the Tracker module. Input
points on the control station are updated from the
device inputs received on the network connected to
the Master. Device output points, depending on the
I/O driver, are written by both the Master and Tracker
module. Role switching is automatic if actual
problems are detected (for example, heartbeat) by
the I/O driver, or the user can switch the roles at any
time via SMDH.
The FBM231 has four ports - each can be
individually configured in software for RS-232,
RS-422 or RS-485. This allows a single FBM231
the flexibility to connect to multiple similar but not
identical devices. Ports 1, 2, 3, and/or 4 can be
configured as a single logical port with redundant
cables allowing you to interface with dual-ported I/O
devices within your plant. The general network
configurations are shown in Figure 1.
The FBM231 and its associated termination
assemblies (TA) accommodate several types of
connections to dual-ported devices; direct
connection to devices; connection to modems when
used with the RS-232 communication interface, and
multidrop connections to RS-485 devices. Intrinsic
safety devices can be connected between the TA
and the field device. For single ported devices, you
should use the FBM230.
selectable bus termination resistors per port. For RS232 wiring, the TA has four standard DB-25 male
connectors and a break-out bank of 24 DIP switches
for each port that can be used for any RS-232 wiring
configuration (for example, to connect Clear-to-Send
to Request-to-Send).
Physical wiring is in accordance with Electronic
Industrial Association (EIA) standard RS-232,
RS-422, or RS-485.
I/O DRIVERS
This FBM is a generic hardware module in which
different software drivers can be loaded. These
drivers configure the FBM to recognize a particular
protocol used by the field device. Several of the
software drivers are standard product offerings.Other
custom drivers can be developed to meet specific
needs. These drivers are dynamically downloaded to
the pair of FBM231s with software code specifically
designed to interface with the third party devices
protocol. The configuration procedures and the
software requirements for each driver are unique to
the device(s) being integrated into the system.
CONFIGURATOR
The FDSI configurator sets up the FBM231 port via
XML based device configuration files. The port
configurator allows for easy setup of the
communication parameters for each port (such as,
communication interface standard, baud rate, parity).
The device configurator is not needed for all devices,
but when needed it configures device specific and
point specific considerations (such as, scan rate,
address of the data to be transferred and the amount
of data to be transferred in one transaction).
PSS 21H-2Z31 B4
Page 3
Z
C
P
Z
C
P
Ethernet
Switch
Ethernet
Switch
F
C
M
F
C
M
Control
Processor
ZCP270
Ethernet
Ethernet
Switch
Switch
Field
Control
Processor
FCP270
F
C
P
Field
Communication
Module
FCM100Et/
FCM100E
F
C
P
To Other
FBMs
To Other
FBMs
2 Mbps
Module
Fieldbus
FBM231
1 2
Termination
Assembly
Four Ports
TA
2 Mbps
Module
Fieldbus
FBM231
3 4
1 2
TA
2
3 4
FBM231
1 2
Termination
Assembly
Four Ports
TA
Slave
Devices
TA
Modem/
Converter/
Device
TA
2
3 4
RS-485 Multidrop
Without Modems or Converters.
Dual-ported Devices.
TA
2
TA
1 2
Slave
Devices
FBM231
3 4
TA
4
Modem/
Converter/
Device
Modem/
Converter/
Device
Modem/
Converter/
Device
RS-232/RS-422
Dual-ported devices.
NOTE: Each FBM231 port (1 through 4) can be individually configured for RS-232, RS-422, or RS-485
communication standards.
Figure 1. FBM231 in Typical Network Configurations
PSS 21H-2Z31 B4
Page 4
OPERATIONS
BOUT
Binary Output
IIN
Integer Input
IOUT
Integer Output
PAKIN
Packed Input
PAKOUT
Packed Output
PLSOUT
Pulse Output
RIN
Real Input
RINR
ROUT
Real Output
STRIN
String Input
STROUT
String Output
Binary Input
BINR
HIGH RELIABILITY
The redundancy of the module pair, coupled with the
high coverage of faults, provides very high
subsystem availability time.
Either module may be replaced without upsetting
field input or output signals to the other module. A
module can be removed or replaced without
removing field device termination cabling, power, or
communications cabling.
PSS 21H-2Z31 B4
Page 5
FIELDBUS COMMUNICATION
The Fieldbus Communication Module (FCM100Et or
FCM100E) or the Field Control Processor (FCP270)
interface the redundant 2 Mbps module Fieldbus
used by the FBMs. The FBM231 accepts
communication from either path of the redundant 2
Mbps module Fieldbus - should one path fail or be
switched at the system level, the module continues
communication over the active path.
VISUAL INDICATORS
Light-emitting diodes (LEDs) incorporated into the
front of the module provide visual indication of the
modules operational status, and the communication
activity (transmit and receive) of each of the four
communication ports. Two additional LEDs indicate
the master or tracker status of the modules.
TERMINATION ASSEMBLY
The FBM231 termination assembly (TA) is part of the
I/A Series system DIN rail mounted subsystem field
wiring termination family.
Each FBM231 TA and its associated termination
cable provide connection compliance to the electrical
rail mounting
Three-tier termination for RS-422 and RS-485
PSS 21H-2Z31 B4
Page 6
F U N C T I O N A L S P E C I F I C AT I O N S
Device Communications
INTERFACE
Four serial I/O communication ports interface four
direct connect RS-232, RS-422 dual-ported
devices or up to 64 dual-ported devices via four
RS-485 buses (Up to 16 devices per port). Each
port is a dual-logical port to dual-ported devices.
BUS CHARACTERISTICS
General
Electronic Industrial Association (EIA)
RS-232, RS-422 or RS-485 communications
selectable on a per port basis. The RS-485
physical communication medium consists of
twisted-pair shielded copper cable
containing a single conductor pair. The
RS-422 is a 4-wire physical communication
medium. The RS-232 physical
communication medium is a DB-25 cable to
a customer supplied
device/modem/converter.
EIA RS-232, RS-422 and RS-485 I/O
Communication
Type
Asynchronous communication, direct
connect link (RS-232).
Transmission Rate
300, 600, 1200, 2400, 4800, 9600,
19200, 38400, 57600 and 115200 baud.
Protocol
8-bit characters; odd, even or no parity,1 or
2 stop bits.
NOTE
For driver specific limitations on I/O Capacity
and Data Types Transferred, refer to the
corresponding driver PSS or Users Guide.
I/O CAPACITY
Up to 64 devices per FBM231 maximum (number
of actual devices is performance dependent) with
up to 2000 DCI point connections.
PSS 21H-2Z31 B4
Page 7
F U N C T I O N A L S PE CI F I C AT I O N S ( C O N T I N U E D )
Regulatory Compliance
ELECTROMAGNETIC COMPATIBILITY (EMC)
European EMC Directive 89/336/EEC
Meets: EN 50081-2 Emission standard
EN 50082-2 Immunity standard
EN 61326 Annex A for Industrial
Environments
CISPR 11, Industrial Scientific and Medical
(ISM) Radio-frequency Equipment Electromagnetic Disturbance Characteristics
- Limits and Methods of Measurement
Meets: Class A Limits
IEC 61000-4-2 ESD Immunity
Contact 4 kV, air 8 kV
IEC 61000-4-3 Radiated Field Immunity
10 V/m at 80 to 1000 MHz
IEC 61000-4-4 Electrical Fast
Transient/Burst Immunity
2 kV on I/O, dc power and communication
lines
IEC 61000-4-5 Surge Immunity
2kV on ac and dc power lines; 1kV on I/O
and communications lines
IEC 61000-4-6 Immunity to Conducted
Disturbances Induced by Radio-frequency
Fields
10 V (rms) at 150 kHz to 80 MHz on I/O,
dc power and communication lines
IEC 61000-4-8 Power Frequency Magnetic
Field Immunity
30 A/m at 50 and 60 Hz
PRODUCT SAFETY
Underwriters Laboratories (UL) for U.S. and
Canada
UL/UL-C listed as suitable for use in
UL/UL-C listed Class I, Groups A-D;
Division 2; temperature code T4 enclosure
based systems. Communications circuits
meet the requirements for Class 2 as defined
in Article 725 of the National Electrical Code
(NFPA No.70) and Section 16 of the
Canadian Electrical Code (CSA C22.1).
Conditions for use are as specified in the
I/A Series DIN Rail Mounted Subsystem
Users Guide (B0400FA).
European Low Voltage Directive 73/23/EEC
and Explosive Atmospheres (ATEX) directive
94/9/EC
CENELEC (DEMKO) certified as EEx nA IIC
T4 for use in CENELEC certified Zone 2
enclosure certified as associated apparatus
for supplying
non-incendive field circuits for Zone 2, Group
IIC, potentially explosive atmospheres when
connected to specified I/A Series processor
modules as described in the I/A Series DIN
Rail Mounted Subsystem Users Guide
(B0400FA).
Calibration Requirements
Calibration of the module or termination assembly is
not required.
PSS 21H-2Z31 B4
Page 8
E N V I R O N M E N TA L S P E C I F I C AT I O N S
Operating
Contamination
Suitable for use in Class G3 (Harsh) environments as
defined in ISA Standard S71.04, based on exposure
testing according to EIA Standard 364-65, Class III.
TEMPERATURE
-20 to +70C (-4 to +158F)
RELATIVE HUMIDITY
5 to 95% (noncondensing)
Storage
TEMPERATURE
-40 to +70C (-40 to +158F)
RELATIVE HUMIDITY
5 to 95% (noncondensing)
P H Y S I C A L S P E C I F I C AT I O N S
Mounting
The FBM231 mounts on a Modular Baseplate. The
Modular Baseplate can be mounted horizontally or
vertically on a DIN rail, or mounted horizontally in a
19-inch rack using a mounting kit. Refer to
PSS 21H-2W6 B4 for details.
The TA has a combination foot that supports 32 or
35 mm DIN rail mounting.
Part Numbers
Module - P0926GV
TA Ring Lug - P0926PA
TA Compression Screw - P0926GH
Dimensions - Module
HEIGHT
102 mm (4 in)
114 mm (4.5 in) including mounting lugs
WIDTH
45 mm (1.75 in)
DEPTH
104 mm (4.11 in)
Dimensions - TA
See page 10 and page 11.
Mass
MODULE
284 g (10 oz) approximate
Termination Assembly
Ring Lug (P0926PA)
363 g (0.8 lb) approximate
Compression Screw (P0926GH)
272 g (0.6 lb) approximate
Cables
FBM231 TO TA LENGTHS
1 m (3 ft) to 5 m (15 ft)
TERMINATION CABLE TYPE
Type 5 - Refer to Table 1 on page 9
TA RS-232 CONNECTION (DB-25 CABLE) TO
MODEM/CONVERTER/DEVICE
Up to 15 m (50 ft) for custom cables per EIA
Standard RS-232.
RS-422 AND RS-485
Up to 1200 m (3960 ft)
PSS 21H-2Z31 B4
Page 9
Type 5
LSZH(a)
Type 5
Hypalon/XLPE(b)
1.0 (3.2)
P0928AW
P0926GJ
2.0 (6.6)
P0928AX
P0931RV
3.0 (9.8)
P0928AY
P0926GQ
5.0 (16.4)
P0928AZ
P0926GR
(a) Low smoke zero halogen or low smoke free of halogen (LSZH) is a material classification used for cable
jacketing. LSZH is composed of thermoplastic or thermoset compounds that emit limited smoke and no
halogen when exposed to high sources of heat. Temperature range: -40 to +105C (-40 to +221F)
(b) H/XLPE is Hypalon outer jacket and XLPE (cross-linked polyethylene) primary conductor insulation.
Temperature range: -40 to +90C (-40 to +194F). Hypalon cables are no longer available for purchase.
PSS 21H-2Z31 B4
Page 10
DIMENSIONS - NOMINAL
Compression Screw Termination Assembly (P0926GH)
125
4.93
mm
in
72
80
2.83
3.13
216
8.51
216
8.51
PSS 21H-2Z31 B4
Page 11
DIMENSIONS - NOMINAL
Ring Lug Termination Assembly (P0926PA)
mm
in
PSS 21H-2Z31 B4
Page 12
R E L AT E D P R O DU C T S P E C I F I C AT I O N S H E E T S
PSS Number
Description
PSS 21H-2W1 B3
PSS 21H-2W2 B3
InvensysLogo_TM_2.ai
MB 21A
0313