Professional Documents
Culture Documents
Natural Plasters
Natural Plasters
Things to be Aware of
Maintenance Plaster does crack occasionally, due to freezing and thawing, as well as
the settling of buildings. Earthen plaster is remarkably easy to fix just mix a bit of
plaster and alis!
Plaster May Dust If it is not prepared and applied correctly. Additives can assist this,
as well as giving your finish coat a good dry polish.
Clay
Clay Soil, on a molecular level, is made up of tiny plates that slide over and adhere to
each other. When water contacts these molecules, it binds to them, and forms a bridge
between them, causing them to expand. When they dry out, they contract (this is why
clay cracks) This property causes clay to form a natural barrier to deep penetration of
moisture, a sort of self-sealing top layer, unlike cement plasters, that wick moisture all
the way through. However, it still allows vapor permeability.
Clay is sticky and sculptable, and comes in a rainbow of colors, naturally!
Identifying clay: Get down under the humus!
Worm Test/Ball test
Make a dirt worm or a ball out of damp soil. A clay worm will be moldable,
and will not break easily.
Jar Test:
Fill a glass jar 1/3 full of dirt, and fill the rest with water. Shake well very
well! Let settle the clay will settle last. If your jar is cloudy for hours after
the shake test youve got clay! Ideally, you want at least 20 percent clay in
your plaster dirt.
Clay vs Silt
Silt is made of tiny particles of rock that are larger than clay but smaller than sand. Silt
often feels slippery, like clay, so knowing your silt/clay difference is crucial. Clay is
STICKY, silt is slippery. Your dirt worm will break apart easily. Another test take
a small clump of wet soil, flatten it against your palm, and turn your hand over a clay
will stick, silt will not.
Sand
Sand is the strength of the plaster. The sand prevents the plaster from cracking and
flaking off, and provides structure to the plaster. If you are a hard-core DIYer, or just
love things being free and want to collect beach sand, do give it a good rinse before using
it in plaster, as the salt will crystallize on the surface of your plaster.
Fiber
Fiber is the reinforcement and tensile strength element. Any kind of mold and proteinfree fiber can be used hair, straw, hemp, cattail fluff, manure. Straw is nice for its
availability. Make sure it is bright, and does not arrive damp.
Additives
Flour paste, Manure, Prickly pear juice, fine fiber, lime, mica.many more!
These three things together form the basis for most traditional architecture across the
world, and, thankfully, are re-emerging!
Mixing it Up
Tips: Mix the clay and sand, adding the sand first to prevent clumping. Add water a
LITTLE at a time for some odd reason, if your mix gets too wet, it is difficult to get the
mix just right again. Then blend in the fiber. For small jobs, a wheelbarrow is fine.
For large jobs, use the pit or tarp method, or a cement mixer.
Application:
Mask everything you dont want mud on, and lay tarps. Remember to work slowly and
steadily to avoid waste.
Do Tests to make sure you have a good mix if it cracks, it needs sand. If it falls
apart, it needs clay.
If your plaster is needing to go over a non-porous material, like metal or tarpaper (or even
some kinds of milled lumber) there are a few techniques that make this feat possible
(although not for large stretches of metal and tarpaper). Some plasterers like to use
stapled metal lath to plaster over. This works fine, but must be done with great care to
avoid air pockets. Air pockets create weak plaster. Another technique is to make a
thick cob, or a straw-clay, and apply this in layers, allowing it to dry. Then you can
continue the plaster. In the case of metal, or large expanses of wood, I would apply our
adhesion coat, then a high fiber plaster layer, then the fine plaster.
Adhesion Coat
Cooked flour paste, mixed with sand, finely chopped straw or other fiber, and a handful
of clay. Sticky gooey textured adhesion.
Cooked Flour Paste Recipe
1. Add 1 quart white flour to 2 quarts cold water, and set aside. This should be
reminiscent of pancake batter.
2. Boil another quart water. When boiling, add the mixture of flour and cold water. Turn
heat to low, and continue to cook until the mixture thickens. Continually stir the bottom
to prevent burning.
This is wallpaper glue, and is used to add plasticity to plaster, as a primary ingredient in
our form of alis (clay paint) and in adhesion coats.
On a bale, earthbag, adobe, or other wall, use three coats, after filling in
any gaps with a mixture of clay-coated straw (straw-clay) or cob.
Slip Coat
A hand-applied creamy clay slip.
This coat, pushed strongly by hand onto the substrate, allows the infill coat to
be troweled on nicely, easily adhering to the clay underneath. It also allows
the plaster to have a firm attachment (no air pockets) to the wall beneath, a
key factor to achieve good wall strength. This is created simply by mixing
your clay with water until you get something in between cake batter and
cream. You want some substance, but not too much.
Infill Coat
screened clay soil, sand, fiber, additives optional
I like to trowel on this coat, for simply achieved smooth walls in the end. This
coat is typically thick, and coarse grained sand and a good amount of well
chopped straw is recommended to decrease the likelihood of cracking and add
tensile strength. I like to add flour paste for workability and a cup of lime
water or cup of lime per wheelbarrow full to kill any mold spores.
Finish Coat
screened clay soil, sand, fiber optional, additives recommended
This is the base coat for any color you are going to want on your wall. If
you have found a nicely colored natural clay, this might be just fine. If
you are wanting a white, yellow, or otherwise light colored wall,
purchased white kaolin is a good choice. I find kaolin to be less sticky
than the natural clays I have access to, so I always add flour paste to this
layer, enabling me to add enough sand to prevent cracking, and still have a
workable plaster.
Lime Plasters
Lime Plaster is a mix of hydrated lime and sand. Lime is a natural material, although it
doesnt appear in plaster form in nature.
CaCO3 (limestone) is burned, releasing water and CO2. It is bagged and shipped as
quicklime and then we soak it in water, mix it with sand, and apply it to our wall, where
it CHEMICALLY cures back into limestone, releasing water and absorbing CO2.
Lime, like cement, is also caustic, and will burn your skin and damage tools if left on.
Caution is key, goggles and protective clothing are as well. Keep vinegar handy to stop
the burn if skin contact is made.
Sand: You want to find rough, mixed grade sand for a stronger lime plaster
We usually do three coats with finer and finer plaster if using solely lime.
First two coats: 1 part lime to 2-3 parts sand, fiber additives optional
Finish Coat: 1.5 parts lime to 2-3 parts sand
If you want smooth walls that don't reveal the shapes of the bales, you are
probably looking at a lot more labor and time. And then, with each new
batch of dirt, there are the potential surprises. In this country, we are only
beginning to recover the lost art of earthen plasters.
A hundred years ago in New Mexico, each village had its own location for
the best plaster dirt. Adobes could be made from virtually any earth, but
the plaster dirt was special and was often carted, if necessary, to the
building sites. Its properties were known and loved, and the techniques for
working with that particular dirt were passed down from mother to daughter
in the tradition of the enjarradoras.
Unfortunately, much of that plastering knowledge was lost with the arrival
of the upstart newcomer, cement. The source sites for the dirt are
remembered by few. Carole Crews, Cornerstones (the folks who restore
the old adobe churches in NM), and others have done a lot of research into
the old ways. Susan Barger has some fascinating interviews with older
folks who remember participating in the plastering as kids. She also
analyzed old plaster samples, looking for clues to what makes a durable
mix. Ms. Barger found the chemical reactions in mud plasters to be so
complex that they had more questions than answers at the end of the
research. Clearly more is needed.
But even if we understand how to work with one particular dirt, the fact
remains that the soil of Santa Fe is different from the soil in Oregon. In
fact, the dirt under my feet may be completely different from the dirt 30
yards away.
So What Does This Mean?
First of all, relax. Earth plastering is easy. Once in the mud, many of us
feel we are remembering information our cells have tucked away for us
long ago. Getting in the mud helps us access that knowledge. I had a
similar experience in one of Robert Laporte's timber framing workshops.
After struggling with the chisels for days, feeling clumsy and awkward, I
experienced something clicking in, and all of a sudden I was handling that
chisel like I'd been doing it for years.
But we shouldn't have to rely completely on intuition and memory of past
lives! Or whatever it is that happens in those magical moments. So here
are some tips avoiding potential problems and keeping the fun in the mud.
First, ask yourself these questions:
1.
How much durability do I want and need? Is it a meditation hut or
a conference center? Do you have ten kids?
2.
How much time do I have? (If you need it finished this week, call
the local cement stucco crew. Earth plasters take longer. Plan it into your
schedule. Prioritize the areas that need to be finished first. Prioritize the
exterior if winter is coming on. Interiors can be done in cold weather, but
see sidebar cautions about plastering in winter.)
3.
How much money can I put into this? If you are on a tight budget,
get your friends to help you and/or do workshops. The materials are dirt
cheap and the labor will be free. If it is a big house, consider bringing in an
experienced person to show you the ropes and help you figure out the
mixes. If you want to hire a crew and want smooth, polished walls, expect
to spend more than you would for cement stucco. If anyone out there
knows how to make it less expensive, write an article and let us know!
4.
What do I want the finished walls to look like? It takes more labor
and materials to create smooth walls out of lumpy, undulating bale walls. If
you like the natural curves, keep them!
5.
What materials do I feel comfortable using? The mining of
materials - even dirt - is harmful to the earth. Look first at what is around
you, and what friends have available on their lands. Try to use materials
that have the least impact to create the plasters you want and need. We
will all make different compromises - make sure yours feel ok to you. And
get creative if compromising doesn't work for you. Perhaps you'll discover
something that will help us all out!
Forgo chicken wire.
It's labor-intensive, a pain to work with and prevents you from working the
plasters deep into the bales. Cedar Rose developed the idea of using a
drywall texture gun to spray a thin clay slip onto the bales before plastering
in order to help the plasters really grab onto the straw. It Works. (You can
also apply the slip with your hands, but it's really messy).
I now use the following system: patch holes first by stuffing them with straw
dipped into a clay slip. Let the patches dry. Spray the walls once with a
clay slip, and have others come behind working the scratch coat in with
their hands before the slip dries. Don't build out the wall at all, just work
that first coat deep into the bales. (The elements of this system all came
from Cedar Rose.)