Professional Documents
Culture Documents
Fados9f1 User Manual
Fados9f1 User Manual
PRODUCT DESCRIPTION
The Prot Ar - Ge Endstriyel Proje Tasarm Teknolojik Ar - Ge Ltd. ti. (Prot R&D Industrial
Project Design R&D Ltd. Co.) FADOS9F1 Trouble Shooting & Oscilloscope Device is
designed for trouble shooting all types of electronic boards. The FADOS9F1 is a PC-based VI
Test Voltage Current Analysis device.
2 unique capabilities are added to the FADOS9F1 over the FADOS7F1. The first feature is the
Programmable DC Power Supply; thanks to the 0-16V and 20-1500mA adjustable power supply,
the DC Voltage/Current graphs of the electronic board power supply can be produced. The
second feature is the IR Remote Temperature Measurement Sensor; this sensor is used to
find the components that heat up by drawing too much current. Using these two features
together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These
features can be used as a new technique for trouble shooting.
Signature Analysis is a power-off test method that is used to troubleshoot circuit boards.
FADOS9F1 works by applying a current-limited sine wave through a serial resistor point of
touched on circuit and Voltage-Current (Signature) graph is displayed on the computer screen.
In addition to these features, the computer software analyzes the Voltage Current graph and
shows the equivalent circuit diagram and the electronic components of the contact point. Those
futures are intended to provide guidance to the user in order to facilitate trouble shooting.
Using the Dual Channel VI test feature, the intact and defective (or suspect) electronic boards
can be compared by touching the same points on each board at the same time, thus the out-oftolerance malfunctions can easily be diagnosed with this method. All the VI graphs are
produced by the software making analyses at 720 separate points with an accuracy of 2.5 mV.
Therefore the FADOS9F1 is very accurate.
Memory Recording feature; by means of this feature, the characteristics of the intact electronic
board ( VI graph, equivalent circuit diagram and electronic components values) are written on
the computers hard disk and taking these points as reference, you can compare the defective
(or assumed to be defective) electronic boards accurately, easily and rapidly. At the same time,
the data can be written on the photograph of the board. Thus, the recorded point can be seen
on the photograph while making a comparison from the memory.
The software produces different sounds while comparing the matching and non-matching points
during the test, thus allowing to concentrate only on the sound for a rapid comparison without
2
having to look at a board or display continuously. The user can compare the electronic boards
from 3 different settings at the same time. (Selected Current-Voltage-Frequency steps)
In addition to the above features, the VI FADOS9F1 Test Device can be used as a Dual-channel
Oscilloscope, Square Wave Generator and Analog Voltage output. When the Square Wave
Signal Output is used, a signal is applied to the electronic board and the other channels display
the output signals on the oscilloscope screen.
Technicians, engineers and hobbyists have found VI graph to be an effective and efficient
method for troubleshooting printed circuit boards. The signature comparison method is easy to
use and allows for immediate feedback that will assist you in locating faulty component. As you
gain some experience with VI graph you will realize that FADOS9F1 is an indispensable
troubleshooting tool. Usage is very easy and users will find the faults just by looking at graphs
without comparison.
When test Printed Circuit Assembly (PCA) with FADOS9F1, do not apply power to PCA. PCA and
the devices must be made high-voltage capacitor discharges. There is no risk of further damage
to the PCA while testing and troubleshooting.
FADOS9F1 is easy to carry since its small. It can be carried in a laptop briefcase. Including
many more features, it is like a Swiss knife of users dealing with electronics.
Usage Areas
ECU Automotive electronic circuit boards, servo-step motor drivers, circuit boards of medical
devices, military electronic circuit boards, computer and monitor circuit boards, television-audioradio circuit boards, circuit boards of textile machines, mobile phone electronic circuit boards
etc. (all type electronic circuit boards.)
Electronic Components Test: Resistors, Capacitors, Inductors, Diodes (General purpose,
Zener, High Voltage etc.) Transistors (NPN, PNP, JFET, MOSFET etc.), SCRs, TRIACs,
Optocouplers, Integrated Circuits (Digital, Analog) etc.
Unique Features
Integrated DC Power Source, IR (infrared) Sensor (Temperature Test), Equivalent Circuit
Diagram and Measuring Values of all Components features are unique in the World.
Integrated DC Power Source: It can be adjusted between 0-16V and 20-1500mA with power
output. It gives energy to circuit boards and creating Power DC Voltage-Current Graph.
IR (infrared) Sensor (Temperature Test): This feature is used for detecting more heated
components and draw out heat map of electronic card.
Equivalent circuit diagram and measuring values of all components features; as an example; if
resistor connected parallel to capacitor, it shows circuit diagram and value of them at the same
time.
SECURITY
1- FADOS9F1 is produced by using lead-free solder and designed in accordance CE
regulations; users must use the following usage rules.
2- Chassis must be isolated and grounded. Connect the chassis ground connection point of
the probe is the same as your computer, careful to avoid the potential difference.
3- Feature of oscilloscope, if probe key is set to 1X, it measures 12 Voltage, probe key is
set to 10X, it measures 100 Voltage. Do not use above these limits of voltage.
4- It tests electronic circuit boards without giving to energy. Before test, electronic circuit
board and the devices must be made high-voltage capacitor discharges.
5- The users of this equipment must have knowledge and experience to repair of electronic
circuit boards. Thus, during using FADOS9F1, do not make this mistakes such as touch
chassis to high-voltage, non-isolated ground, test high-voltage capacitor discharges.
Without enough knowledge and experience in this subject, keep away high voltages such
as mains voltage which can damage the system and themselves.
6- Giving high-voltage from probes, series resistors which contained in the device damaged
and makes the circuit an open circuit. In this case, the computer port which is connected
device via USB port damaged but observed in other parts of the computer is not
damaged.
Resistor: %2
Capacitor: %3
Note 1: These tolerances valid, if resistor curve makes angle between 10 and 80 degree to
horizontal axis. If resistor curve close to horizontal line, select Low Current Step and; if resistor
curve close to vertical line, select Middle or High Current Step for reducing mistake rate.
Note 2: These tolerance valid, if capacitor ellipse of width/length ratio is greater than 1/4. This
ratio is less than 1/4 and ellipses width - length is thin and long. In such a case; change
current step or/and frequency step for selecting step appropriate to components.
4- Oscilloscope voltage measurement tolerance: %0,5.
1 FADOS9F1 Product
1 IR Temperature Probe
2 Oscilloscope Probes
1 USB Cable
1 DC Cable
1 Power Adapter
1 Handbag
Test Resistance
Test Frequencies
:2
Hz
Low2 Frequency
:4
Hz
Low1 Frequency
: 12
Hz
Test Frequency
: 32.5
Hz
High Frequency
: 355.4
Hz
Number of Channels
Scan Mode
Other Feature
IR (Infrared) Sensor
C- PC OSCILLOSCOPE FEATURES:
Sampling Rate
: 400 K/S
Input Voltage
: Probe 1X: 12 V
Channel / ADC
: 2 Channel / 12 Bit
Accuracy
: 2.5 mV
Display speed
Momentary Memory
: 64 Kbyte
: Channel 2
Output Voltage
: -12V.+12V (Adjustable)
Frequency (Digital)
Dimensions
Weight
CONTENTS
Page
PRODUCT DESCRIPTION ................................................................................. .2
USAGE AREAS ............................................................................................................... 3
ELECTRONIC COMPONENTS TEST ....................................................................................... 3
UNIQUE FEATURES ......................................................................................................... 4
SECURITY ............................................................................................................... 4
FADOS9F1 PERFORMANS AND MEASURUMENT TOLERANCE ................................. 5
PRODUCT OVERVIEW AND CONTENT .................................................................... 6
FADOS9F1 TECHNICAL SPECIFICATIONS ............................................................... 7
FADOS9F1 FAULT DETECTOR & OSCILLOSCOPE ..................................................... 9
INSTALLATION - DRIVER INSTALLATION .............................................................................. 11
CONNECT PROBES ......................................................................................................... 12
GENERAL USAGE INFORMATION .......................................................................... 12
POWER IR TEMPERATURE TEST ........................................................................ 14
POWER (SUPPLY) TEST DC VOLTAGE CURRENT GRAPH ..................................................... 16
COMPARISON OF THE POWER (SUPPLY) DC VI GRAPH WITH THE FAULTY BOARDS DC VI GRAPH ..... 17
IR TEMPERATURE TEST ........................................................................................ 20
RECORDING THE COMPONENTS TEMPERATURES .................................................................... 20
TEMPERATURE CHECKS OF THE FAULTY ELECTRONIC CIRCUIT BOARD ......................................... 21
MICRO - VOLT ............................................................................................................. 21
VI TEST PROGRAM FEATURES OF FAULT DETECTION PART .............................. 22
PASSIVE COMPONENTS R, L, C V/I GRAPH .......................................................... 23
RESISTOR VI GRAPH ..................................................................................................... 23
CAPACITOR VI GRAPH ................................................................................................... 25
CAPACITOR QUALITY TEST AND RC CIRCUIT ....................................................................... 26
SEMI CUNDOCTORS V/I GRAPH ........................................................................... 27
DIODE, ZENER DIODE VI GRAPH ...................................................................................... 27
TRANSISTOR TRIAC THYRISTOR FET IGBT VI GRAPH ................................................... 28
INTEGRATED CIRCUITS (ICs - SMD INTEGRATES) V/I GRAPH ............................ 30
SAVING AN ELECTRONIC CIRCUIT BOARD TO THE MEMORY AND COMPARISING
FROM MEMORY..................................................................................................... 31
RECORDING THE TEST POINTS WITH IMAGE ........................................................................ 31
COMPARITIVE TEST OF THE COMPONENTS OF IN THE CIRCUIT BOARDS ........... 33
3G 3 DIFFERENT GRAPHS DISPLAY ................................................................... 39
OSCILLOSCOPE PROGRAM FEATURES ............................................................... 38
RECOMMENDATIONS............................................................................................ 42
WARRANTY AND CONDITIONS............................................................................. 43
8
Picture 2: FADOS9F1
FADOS9F1 includes 9 important functions:
1. Double Channel Fault Detection (Analog Signature Analysis - VI Graph)
Comparing good and faulty or suspect circuit boards without giving power to boards.
2. Programmable Integrated DC Power Supply
For giving energy to circuit boards and creating Power DC Voltage-Current Graph.
3. Non Touched IR Temperature Sensor
For detecting more heated components and draw out heat map of circuit board.
4. Equivalent Circuit Diagram
Composing R, C, or Diode Circuit Diagram according to the point touched.
5. Measuring Value of Resistors, Capacitors, and Diodes
Feature of measuring the value of touched point.
6. Fault Detection by Comparison from Memory
By recording data of good circuit boards to memory, comparing faulty or suspects boards
from memory.
7. Double Channel Digital Oscilloscope
As occasion may require, device can be used as oscilloscope.
8. Square Wave Signal Output
Ch.1 is used as oscilloscope and Ch.2 is used as signal generator.
9. Analogue Voltage Output
Ch.1 is used as oscilloscope and Ch.2 gives analog voltage output.
9
Or
Click Start
Click Settings
3- Find Prot Ar-Ge FADOS9F1 Fault Detector inside Universal Serial Bus Controllers and
click right then, select update software driver.
4- Select (Search for the best driver location) and click browse, find FADOS9F1 Drivers
folder.
5- Click OK and install driver.
Note: Each product has different calibration settings, so that please do not lost the FADOS9F1
program CD.
CONNECT PROBES:
Connect the DC Power Cable (Red-Black Cable) to the Power connector. Connect IR Sensor to
IR Temp. connector. The Oscilloscope Probes and Com Probe (Crocodile) can be connected
each VI Tester sockets. The probe with the yellow circle is always Channel 1; the probe with
the blue circle is always Channel 2. The crocodile probe is always Com. USB cable is used for
communication between the computer and FADOS9F1. Connect the Power Adaptor to the mains
plug (18-20 VDC).
GENERAL USAGE INFORMATION
1. When run software, Power The IR Temperature Test screen opens and an input is
entered to the VI Tester screen or Oscilloscope Analog Output screen with the VI
Tester button.
While testing the Electronic boards, we recommend the user to use the Power IR
Temperature Test feature for testing.
Firstly, create good circuit boards Power Voltage/Current Graph. Than save this graph
to memory.
Compare
faulty
or
suspect
circuit
boards
12
with
good
circuit
boards
Power
Voltage/Current Graph.
If the faulty or suspect board draws too much current, it means that one or more
components on the board are heating up. Use the IR sensor for trouble shooting the
heating components.
If the faulty (defective) board draws less current than the good (intact) board, it means
an open circuit in the board. In this case, the Oscilloscope Screen can be opened to
diagnose the line that does not receive power.
If the graphic of the faulty (defective) board is the same as the good board, the faulty
component can be diagnosed by opening the VI Tester Screen.
2. Open circuits graph is in the middle and horizontal position at Test-Fault Detect screen.
Current Voltage Graph (VI) makes angle according to the value of resistance, capacitor
is like circle and ellipse, short circuit is vertical position.
3. In the Medium current mode, in the areas with high resistor values, if the VI graph is
closer to the horizontal axis, you can see the resistors with high values more clearly by
switching to low current. If the VI graph is too close to the vertical axis, this means that
the resistor value is low and you can read the values more clearly by switching to the
high current mode.
4. Please test the capacitors in the high frequency mode generally. Use low current when
the capacitor value is low and high current if the value is large. If the capacitor value
resembles a thin line in high current at the vertical axis, you can see the value more
clearly by reducing the frequency from the frequency mode.
5. The pins of a good integrated circuit are generally in form of a dual reverse diode (other
than the supply and ground). Although the attached resistors and/or capacitors might
affect the graph, the two reverse diodes should be observed. In the output of some
integrated circuit only one diode may also be seen. But an image in form of a resistor
would most probably mean a defective integrated chip.
6. The capacity test shows the quality of the electrolytic capacitor in particular. The more
horizontal this curve is, the higher the quality of the capacitor is. The angle of the
deteriorating capacitor makes an angle with the horizontal. If the angle is large, it means
a defective capacitor. Because the circuit draws a current while in the board, this test
can be deceptive, hence consider this while testing. In case of doubt, remove the
capacitor from the circuit and then measure; in this measurement, the test devices may
show all of them as intact. The best capacitor quality measurements can be done by
13
looking at the Capacity-Resistor Curve with this product. While making this
measurement, adjust the frequency and current to become longer on the vertical axis of
the graph, but without forming a multiple and thin graph.
7. In case of a misshapen capacitor graph due to the effects of the diodes in the circuit, the
value of the capacitor can be measured again after eliminating the effects of the diodes.
8. The important issue in trouble shooting is the shape of the graphs and their
interpretation. Try to find the defects by comparing when starting. You should be able to
distinguish the graphs of the good and defective materials in a short time. The
Equivalent circuit diagram and values will aid you in the process. If you concentrate on
the values in the equivalent circuit, diagnosing may take longer. Use the values of the
components as necessary, but do not well on the values alone like the measurement
logic of the test equipment. The evaluation logic of this product is based on the
interpretation of the graphs, i.e. interpreting the graphs produced by the computer and
generating the equivalent circuit diagram and showing the associated values.
14
15
Power On
the electronic board draws more current than the set value, the program limits the
current and does not allow excessive current draw.
Power Off
Power Test
Recording
: Opens the file format and starts recording or opens a saved file.
Time
Auto Test
Temp. Zero
circuit.
Current (mA) : Shows the current drawn by
the circuit.
16
C and 10 C.
Comparison of the Power (Supply) DC VI Graph with the Faulty Boards DC VI Graph
Opening Recorded Data : Click Recording Button and select Power Data, then click on
Open Button and to open the selected file.
The DC VI graph of the good electronic board is opened from the memory.
The Power cables are connected to the boards supply. Red Cable (+), Black cable (-).
The Power Test button is pushed to generate a DC VI graph of the faulty board.
18
19
IR TEMPERATURE TEST
Recording the Component Temperatures
Connect DC cable to circuit boards supply. And Click Power On button for giving energy to
boards. The Timer will count down from 90 seconds to 0. Click Record button to open the
picture of the circuit loaded before. The IR sensor is held to a point on the table and the
Temp Zero button is clicked. Then the temperature of the component is measured with the IR
sensor.
The IR sensor is brought over the component to be measured. The measured component is
marked on the photograph. When the Timer counts down to zero, the data is recorded by
clicking the Save button. Then the other components can save.
After waiting 90 seconds, it will be easy to detect more heated components and draw out heat
map of electronic card.
20
Connect the Power cables to the boards supply. Red Cable (+), Black cable (-).
Click the Record (Recording) button, select the IR-Temperature Data and click the
Open button.
Click the Power Test button and wait 90 seconds for the components to warm up.
Measure the temperature of the first component. If the measured temperature is the
same as the recorded data, click on the Next Point to opened the second recorded
data. If Auto Test is selected and the measured temperature is the same as the
recorded data, the other recorded data is opened a few seconds later.
21
22
23
Capacitor VI Graph
The energy storing devices leak voltage and current in the phase shift area. This situation
creates a circular or elliptical shape on the screen. The capacitor current / voltage (VI) graph,
equivalent circuit diagram and values are shown in Picture 15 - 16. Picture 15 - 16 displays
capacitor typical signals and values for the equivalent circuit. The VI graphs of the high value
capacitors are displayed on the vertical axis. For testing high capacitor select high current and
low frequency. The VI graphs of the medium value capacitors are elliptical close to a circle. Low
capacitor generates horizontal ellipse. For testing low capacitor (lower than 10 nF) select low
current and high frequency.
Picture 20: Diode and Serial Diode - Resistor VI Graph, The Equivalent Circuit Diagram
27
Picture 21: Diode VI Graph (Channel1), Zener Diode VI Graph (Channel2), Transmission Voltage
Transistor Triac Thyristor FET - IGBT VI Graph
Active components such as transistor, triac and FET can be tested by transmitting them while
both of two channels are used. A transistor contains two semiconductor junctions connected.
Transistors also must have emitter chassis. First, touch collector with a probe (Channel 1 probe
or Channel 2 probe). Collector must be at non-transmission position. Then, touch other probe
(Channel 1 probe or Channel 2 probe) base in order to provide transistor to start transmitting.
Transistor characteristics should be seen as at the screen. Lack of any leak at the junction point
(fully horizontal) supports the soundness of the material.
The FET is comprised of a channel containing semi-conductor materials and another zone
(gate) made of a semi-conductor material opposite to the foregoing. The Gate shapes the diode
with the connections at both ends of the channel (source and drain) and those diodes can be
tested. Both probes are used for testing the 3-pin active components. One probe shows the
trigger signal and the other shows the conduction state. If conduction occurs; click T.T.T FET
28
IGTB from the test types menu and the software checks if the FET MOSFET is of the N or P
type.
MOSFET are field effect transistors. Gate - drain and gate - source tests generally yield an open
circuit mark. However, some MOSFETs have a protective diode between the gate and source. In
such cases, the gate-source marking is similar to a zener diode. Those are checked like the FET
using the source - drain conduction and gate - source voltage. The MOSFETs on the other hand
are checked by means of the normal and reverse polarization of the gate-source junction.
Triac, Thyristor, IGBT can be tested in the same way.
If Thyristor,Triac, Transistor, FET, IGBT selection (T.T.T FET IGBT button) is applied, type of
component can be determined.
29
30
31
In order to test from saved file, press record memorized test button, select data to be tested
and open first saved point. Saved data is seen as a red graph at first channel. Touch the point
to be tested with second channel. If it is same as the saved data or in tolerance values, it is
written Harmonious at screen. If it is out of tolerance values, it is written Disharmony,
percentage value is seen and wrong voice is heard. When automatic test is activated, if a test
point is harmonious, then it goes to next point automatically. This feature allows rapid testing
without having to look at the monitor.
Note: The test points of the Electronic may be recorded only with Channel 1. The test points
saved with the Recording Menu can be opened as reference and the points on the defective
circuit can be compared with those using Channel 2.
only. If the name is not written as image.jpg, this feature will not work. After loading the
figure, a photograph of the circuit is shown at the lower right corner of the VI test screen. The
green buttons on the photograph for +,-zooming. Select the point to be recorded on the
photograph, then touch the Channel 1 probe to that point and push the Record (Save) button.
When you use this feature for comparing from the memory, you can see the location of the
saved point on the board.
34
there
is
complete
matching
in
the
comparison,
35
this
point
should
be
good.
36
38
40
41
Voltage Display Sensitivity: (Voltage/Division) Adjusts the voltage display sensitivity. The
accuracy of the data received from the product does not change. The figures show the
voltage value. If the figures are double clicked, the 0 V reference of the channel is taken as
the point clicked. Data received from device is 12 Bit, 2.5mV sensitive.
Zero Adjustment: Shifts the 0 V point of the image upwards or downwards. The figures
show the voltage value. If the figures are double clicked, the 0 V reference of the channel
is starts the point clicked.
Starting Point:: Sets the starting point of the displayed section of the image in the
Memory mode.
Time Adjustment: Time/Division. Adjusts the time allocated to each division on the
horizontal axis (time axis).
RECOMMENDATIONS
1. The probes should be set to 1X while trouble shooting (fault detection).
2. Test good (solid) circuit board channel 1, faulty or suspect circuit board channel 2. First
touch the channel 1 probe, and then touch channel 2 probes.
3. The important aspect in trouble shooting is the matching of the graphs. The lower circuit
diagram and values are for assistance purposes. The values in the circuit diagram are not
for measurement but for comparison. Wrong indications may be given with the effects of
the other components on the board.
4. While using the device, testing at the medium current level is recommended. When
necessary, use the low current level (i.e. high value resistors or low value capacitors).
5. When recording in the memory, click save button after touching good (solid) circuit
boards pins with channel 1. When the data open from memory, using Channel 2
comparison data with faulty, suspect or good (solid) circuit board.
6. In the Oscilloscope mode, the 1X setting of the probe measures up to 5V, and the 10X
setting up to 50 volts. Measuring high voltage circuits is not recommended.
7. Each product has different calibration settings. The calibration file can be found on the
CD in the program installation folder. Please do not lose the program CD.
42
43