Professional Documents
Culture Documents
Seawater
Seawater
Safety Note: Safety glasses are required when performing this experiment
Discussion
Seawater
The determination of the salt content of seawater is an important area of research since ocean currents and
global climate are affected by salt content. The primary ionic components of seawater are shown in the
table below. These include large amounts of chloride (Cl–) and sodium (Na+) ions. Several methods are
used to measure the concentrations of ions in water. One method involves measuring electrical
conductivity. Electrical conductivity is dependent on ionic concentration since ions are electrolytes.
Measuring the conductivity can, therefore, give information
Grams per Mass
about dissolved salt concentrations. Another method for Ion
1000 g seawater %
measuring salt concentration is to simply measure the
Cl– 19 1.9
density, or specific gravity, of a water sample. The density
Na+ 10.7 1.07
of water increases with increasing amounts of dissolved
SO42– 2.7 0.27
salts, thereby giving concentration information. But these
Mg+2 1.3 0.13
methods give only the total ionic concentration, not specific
Ca+2 0.4 0.04
information regarding concentrations of individual ions, like +
K 0.4 0.04
sodium or chloride. Today, there are devices called ion-
selective electrodes that can measure the concentration of a specific ion. Another method, called ICP-MS
(inductively-coupled plasma mass spectrometry), can measure very low concentrations of specific
elements. In this experiment we will use a rather simple method for measuring the concentration of
chloride ions in seawater. The method is called a titration and is a quick and inexpensive procedure.
Titrations
A common method used to determine the chloride content of seawater is to use a precipitation reaction
between the silver nitrate and sodium chloride:
Silver(I) nitrate, sodium chloride, and sodium nitrate are all very soluble in water. On the other hand,
solubility rules predict that silver chloride should be insoluble in water. In fact, silver chloride is quite
insoluble in water. Only about 0.0018 grams will dissolve in one liter of water. Since AgCl is insoluble
in water, adding AgNO3 to a sample of seawater will result in the formation of AgCl because seawater
possesses chloride ions. If we can measure the amount of AgNO3 required to react with all of the Cl- in
the seawater, then we can determine the concentration of the Cl- in the seawater. This is the basis of a
titration. We use a reactant of known concentration (in this case silver nitrate) to determine the
concentration of a chemical species in which we are interested (in this case chloride). The reactant for
which we know the concentration is called a titrant. The titrant is usually standardized, meaning its
concentration is accurately measured before performing the titration. The species for which we don't
know the concentration is often called an analyte. The analyte concentration is found by performing the
titration.
Department of Physical Sciences Kingsborough Community College The City University of New York Winter 2008
1
The experimental apparatus used for performing titrations is shown below. In our experiment, silver
nitrate is placed in a buret, an apparatus used to deliver known volumes of the titrant. The analyte
(seawater) is placed in an Erlenmeyer flask. The titrant is slowly added from the buret into the flask, drop
by drop, where the two react with one another. The volume of the analyte is accurately known, as is the
concentration of the titrant. What isn't known is the concentration of the chloride in the seawater or the
volume of the silver nitrate required to react completely with the chloride. The volume of the titrant
required to react with the analyte is measured from the buret, which contains markings that allow us to
determine how much liquid has passed through the opening at the bottom. Once the volume of the titrant
required to react with all of the analyte has been determined, we can calculate the analyte concentration.
Solution
The moles of silver nitrate used in the titration Erlenmeyer
are calculated from the known molar flask with
concentration and the measured volume. seawater
Ring stand
n
Recall that M =
V
⎛ 1molCl- ⎞
moles Cl- = ( 7.775 x10-4 mol AgNO3 ) ⎜ -4
⎟ = 7.775 x10 mol Cl
-
⎝ 1mol AgNO3 ⎠
Silver chloride is a white solid that forms soon after any silver nitrate has been added to seawater. This
makes a quantitative analysis difficult since we want to know when all of the chloride has reacted.
Indicators
To know when the titration has reached the equivalence point (the point at which the moles of titrant
added is equal to the moles of analyte in the sample), we add a material called an indicator to the mixture.
2
Just like the titrant, the indicator also reacts with Ag+ ions. The indicator we will use is called potassium
chromate (K2CrO4). Potassium chromate reacts with silver(I) ions:
Once the chloride in the solution has completely reacted with Ag+ ions any additional silver nitrate reacts
with the potassium chromate. Potassium chromate in water is a transparent yellow solution in water.
When reacted with silver ions the silver chromate solution is an orange-red color. So once the solution
starts to become orange-red, we stop adding the titrant and calculate how much titrant was added.
Procedure
SAFETY PRECAUTIONS
Silver nitrate will stain skin. Safety glasses or goggles must be worn while this experiment is being
performed.
1. Start by preparing the buret. The 50 mL buret should be rinsed with tap water two to three times and
then one time with distilled or deionized water.
2. Obtain 70 mL of silver nitrate in a dry 100 mL beaker. Pour a few milliliters of this solution into the
buret.
3. Let the silver nitrate solution flow through the bottom tip of the buret into a second clean beaker.
Don’t pour any silver nitrate into the sink.
4. Fill the buret with the remaining silver nitrate to near (above) the 0 mL mark of the buret.
5. Allow a few milliliters of silver nitrate solution to pass through the buret by opening the stopcock.
This will push any trapped air out of the stopcock. Record the new volume of the buret in the data sheet
in the row that says initial volume.
Department of Physical Sciences Kingsborough Community College The City University of New York Winter 2008
3
6. Record the concentration of the silver nitrate standard solution on the data sheet.
Steps 7-10 involve diluting the seawater and may need to be performed. Check with your instructor. If
the dilution has already taken place then skip steps 7-10 and obtain 80 mL of seawater in a clean dry 250
mL beaker and go to step 11.
7. The concentration of chloride in the seawater is high and needs to be diluted so we can perform the
titration. Obtain 20-30 mL of seawater in a clean 100 mL or 250 mL beaker.
8. Using the 10 mL volumetric pipette transfer 10.00 mL of the seawater to a clean 100 mL volumetric
flask.
9. Add deionized or distilled water until the flask is about 1/2 full. Shake the flask to mix the seawater
with the deionized or distilled water.
10. Continue adding the water to the flask until the bottom of the meniscus is right at the 100 mL mark of
the flask. This diluted seawater (by a factor of ten) is the solution we will use for the titrations.
11. Using the 25 mL volumetric pipette transfer 25.00 mL of the diluted seawater solution to a 125 mL
Erlenmeyer flask.
12. Using a 10 mL graduated cylinder transfer about 5 mL of 1% potassium chromate (K2CrO4) solution
to the Erlenmeyer flask. It is possible that the potassium chromate has already been added to the
seawater. If so, the seawater will appear yellow and you can go directly to the next step.
13. Begin adding the silver nitrate solution to the seawater, slowly drop by drop. As it drops into the
flask be sure to swirl the flask to ensure that the titrant (silver nitrate) mixes with the contents of the flask.
By adding the titrant slowly you are more likely to obtain good results. You may notice that each drop
causes the surface of the solution to turn orange-red. The endpoint is a very light orange-red color. When
the entire solution turns this color the endpoint has been reached.
14. Once the endpoint is reached stop the titration by closing the stopcock and recording the volume of
the titrant in the buret on the data sheet, in the row that says final volume. The volume delivered is the
difference between the initial and the final volume. The volume delivered should be between 7 mL and
15 mL. If your volume is outside this range you may have a problem and should consult with the
instructor.
15. Perform two more titrations for a total of three titrations, using the same procedure as you used with
the first titration. The initial volume of the second titration will be the same as the final volume of the
first titration.
16. Any unused silver nitrate solution should be poured into the collection bottle provided. The buret
should then be rinsed out with tap water and deionized water. The products of the titrations should be
poured into the appropriate waste container.
9. The density of seawater can be measured by measuring the mass of 25.00 mL of the seawater solution.
Use a digital analytical balance to measure the mass of the seawater in a 100 mL beaker. Use a 25.00 mL
volumetric pipette to measure the volume.
4
Discussion of Calculations
Using the average volume of silver nitrate, calculate the mass percent chloride of the seawater sample.
Show all calculations clearly and in detail on a separate report sheet. The density of the seawater can be
measured or assumed to be 1.02 g/mL.
1. The first step in the calculations is to determine how many moles of titrant (AgNO3) were used. Use
n
the volume of each titration and the known molarity. Recall that M =
V
⎛ x mol AgNO3 ⎞
moles AgNO3 = ⎜ ⎟ ( Volume (L) ) where the molarity is determined prior to performing the
⎝ 1L ⎠
experiment.
2. The moles of sodium chloride in the seawater solution can be determined because the moles of AgNO3
are equal to the number of moles of NaCl at the equivalence point:
4. The mass of chloride ions in the seawater can be found from the number of moles and the atomic mass
of chlorine:
⎛ 35.45g Cl ⎞
mass of chloride = ( moles Cl- ) ⎜ ⎟
⎝ 1molCl ⎠
5. The mass of the seawater used is found from the density and the volume used. We can assume that the
density of the seawater is 1.02 g/mL.
6. It is traditional in oceanography to report concentrations in mass percent. Mass percent is defined as:
⎛ mass of solute ⎞
mass % = ⎜ ⎟ x 100
⎝ mass of solution ⎠
In our experiment chloride is the solute and seawater is the solution. So to find the mass percent we need
to find the mass of chloride in 25 mL of seawater and the mass of seawater in 25 mL.
⎛ mass of chloride ⎞
mass % = ⎜ ⎟ x 100
⎝ mass of seawater ⎠
Department of Physical Sciences Kingsborough Community College The City University of New York Winter 2008
5
7. The seawater sample we used was diluted ten times, so multiply the mass of chloride above by 10 to
get the actual moles of chloride in the undiluted seawater sample.
Questions
1. Why doesn't the buret have to be at exactly 0.00 mL before you start a titration?
2. Why is it important to remove all the air from the tip of the buret before starting a titration?
3. Write the complete ionic and net ionic equations for the reaction between AgNO3 and K2CrO4.
Molecular equation: 2AgNO3 (aq) + K2CrO4 (aq) Æ Ag2CrO4 (s) + 2KNO3 (aq)
4. Write the complete ionic and net ionic equations for the reaction between AgNO3 and NaCl.
Molecular equation. AgNO3 (aq) + NaCl(aq) ⎯⎯ → AgCl(s) + NaNO3 (aq)
5. The 125 mL flask can be wet when the 25 mL of seawater is added using the volumetric pipet. Why
doesn’t the water in the flask cause problems in the calculations?
8. A technician wants to prepare a standard solution of silver nitrate. The concentration of the solution
needed is 0.0750 mol/L with a volume of 1000 mL. Explain and calculate how the technician should
prepare this solution.
6
Observations and Notes
Experiment 6: Volumetric Determination of Chloride Content in Seawater
Date:
Department of Physical Sciences Kingsborough Community College The City University of New York Winter 2008
7
Data Sheet
Experiment 6: Volumetric Determination of Chloride Content in Seawater
Calculate the mass percentage chloride in your sample in the seawater using the average titration volume.
Show these calculations on a separate piece of paper.
8
Calculations Sheet
Department of Physical Sciences Kingsborough Community College The City University of New York Winter 2008
9