Siemens Generator 125 MW 50 HZ
Siemens Generator 125 MW 50 HZ
Kpone
SN = 153,95 MVA PF = 0,85
UN = 15,75 kV fN = 50 Hz Design corresponds to:
The given data are calculated values (if not indicated differently)
Die angegebene Werte sind Rechenwerte (wenn nicht anders bezeichnet)
SIEMENS Beyer/Hait Rev. B
Load Point N A B
Standard IEC 34 IEC 34 IEC 34
Thermal Classification: Design / Using F/B F/B F/B
Power MVA 153,95 205,00 154,00
Cold Air Temperature °C 44,0 10,0 50,0
Voltage kV 15,75 15,75 15,75
Voltage Deviation + - % 5,0 5,0 5,0 5,0 5,0 5,0
Armature Current kA 5,643 7,515 5,645
Frequency Speed Hz rpm 50 3000 50 3000 50 3000
Power Factor - 0,85 0,80 0,80
Excitation No load If0 Uf0 A V 374 118 374 119 374 122
Requirements 4/4-load IfN UfN A V 918 291 1188 378 948 310
5/4-load If5/4 Uf5/4 A V 1088 344 1457 463 1127 369
Cooling Air Losses kW 1648 2186 1667
3
Air flow Temp. rise m /s K 42,0 37,6 42,0 49,8 42,0 38,0
Sudden-SCC IS: 3-phase (peak) kA 129 129 129
at No-Load and IK3: 3-ph. (sustained at IfN) kA 8,5 10,9 8,7
Nominal Voltage IK2: 2-ph. (sustained at IfN) kA 13,5 17,5 14,0
Short Circuit Ratio - 0,61 0,46 0,61
Reactances x"d unsat. sat. % % 14,9 11,2 19,8 14,9 14,9 11,2
x'd unsat. sat. % % 20,4 18,3 27,1 24,4 20,4 18,3
calculated values, xd unsat. sat. % % 180 164 239 218 180 164
tolerance +/-15% x''q unsat. sat. % % 16,4 12,3 21,8 16,4 16,4 12,3
acc. IEC 60034-3 x'q unsat. sat. % % 40,7 36,8 54,0 48,9 40,7 36,8
xq unsat. sat. % % 171 145 228 193 171 145
x2 unsat. sat. % % 15,6 11,7 20,8 15,6 15,6 11,7
x0 unsat. % 7,6 10,1 7,6
xleak unsat. % 11,5 15,3 11,5
Time constants T''d s 0,029 0,029 0,029
at 75 °C T'd s 0,972 0,972 0,972
winding T'd0 s 9,210 9,210 9,210
temperature T''d0 s 0,042 0,042 0,042
Ta s 0,270 0,270 0,270
Resistance Stator winding / phase mΩ 1,69 1,69 1,69
at 20°C Rotor winding mΩ 236,97 236,97 236,97
Voltage PF = rated P.F. % 29,6 36,4 30,4
regulation PF = 1,00 % 23,5 29,4 23,5
Max. unbalanced Continuous % 8 8 8
load Short time i22 * t s 8 8 8
Power at Underexcited Mvar 79,7 79,7 79,7
PF = 0 Overexcited Mvar 116,1 162,7 121,5
Winding temp. rise Stator (RTD) K °C 62 106 85 95 64 114
Winding temp. Rotor (average) K °C 62 106 97 107 67 117
Losses Bearing losses kW 75 75 75
Windage losses kW 540 540 540
Core losses kW 315 315 315
Short circuit losses kW 454 805 454
2
Rotor I R losses kW 276 463 294
Total losses kW 1660 2198 1679
Efficiencies with tolerance 4/4-load % 98,75 98,68 98,66
at brushless excitation 3/4-load % 98,62 98,65 98,52
and rated P.F. 2/4-load % 98,25 98,43 98,13
(incl. bearing losses) 1/4-load % 96,93 97,45 96,74
SIEMENS Beyer/Hait Rev. B
1,1
0,80
1,0
0,9
0,85
0,8
0,7
0,90
0,6
0,5
0,95
0,4
0,975
Overexcited
0,3
0,2
0,1
0,0 1,00
0,0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
1,0
1,1
1,2
1,3
1,4
-0,1
Underexcited
-0,2
-0,3
0,975
-0,4
0,95
-0,5
-0,6
0,90
-0,7 0,00 0,20 0,40 0,60 0,70 0,80 0,85
P/SN
2
U / UN I / IN
1,4
1,8
1,2 1,6
1,4
1
1,2
0,8
1
0,6 0,8
0,6
0,4
0,4
0,2
0,2
0 0
0 0,2 0,4 0,6 0,8 1 1,2
0.00
1,10
rated
1,00
0,90
1.00
0,80
4/4
0,70
-rated
0,60
3/4
IF / IFN
2/4
0,50
1/4
0,40
heating limit of stator and rotor winding
-0.00
0,30
0,20
0,10
0,00
1,10
1,00
0,90
0,80
0,70
0,60
0,50
0,40
0,30
0,20
0,10
0,00
I / IN
Dimensions [mm]:
L1 = 9800 H1 = 1486 Overall weight: 206500 kg
L2 = 7700 H2 = 3300 Stator weight: 170000 kg
1)
L3 = 7100 H3 = 0 Rotor weight: 36500 kg
W1 = 3500 W2 = 1400 Rotor moment of inertia: 4112 kgm²
L4 = 12500 H4 = 7000 Oil flow for both bearings: 160 l/min
for rotor withdrawal crane hook height breakaway torque w. jacking oil: 180 Nm
Preliminary values. breakaway torque w/o jacking oil: 14994 Nm
Exact values are part of detail engineering. Thermal time constants [min]:
Stator Winding: 12,0 min
Rotor Winding: 7,1 min
2)
Estimation for required cooling water flow (for TEWAC - cooling):
Minimal water temperature shall not fall below 15°C ! Exact values are part of detail engineering.
TA(cooling air) - TW(cooling water) Glycol Stand. water temp. rise Required cooling water flow
15 K 0 0% 10 K 139 m³/hour
Cooler design data
No. of elements x capacity per cooler element Admiss. generator output during operation with (n-1) cooler elements
4x25% 67%
1) For cooler in top position.
2) Data are generated independent of cooling method; for DAC- or CACA-applications these data are not applicable.
99,5
99,0
Generator Efficiency [%]
98,5
98,0
97,5
96,5
0,25 0,50 0,75 1,00
Apparent Power Output / Rated Apparent Power Output [p.u.]
10000
not permitted
Permissible Duration Time [s]
1000
100
permitted
10
1
1,0 1,1 1,2 1,3 1,4 1,5
Volts per Hertz [p.u]