Professional Documents
Culture Documents
Nissan Murano CVT
Nissan Murano CVT
C TRANSMISSION/TRANSAXLE
A
SECTION
CVT
CVT
CONTENTS
INDEX FOR DTC ....................................................... 6 . Alphabetical Index ................................................... 6 . DTC No. Index ........................................................ 7 . PRECAUTIONS ......................................................... 8 . Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER ................................................................. 8 . On Board Diagnostic (OBD) System of CVT and Engine ..................................................................... 8 . Precautions for TCM and CVT Assembly Replacement ........................................................................ 8 . EEPROM ERASING PATTERNS ......................... 8 . METHOD FOR ERASING THE EEPROM IN THE TCM ..................................................................... 9 . METHOD FOR WRITING DATA FROM THE ROM ASSEMBLY IN THE TRANSAXLE ............. 9 . CHECK METHOD ................................................ 9 . Removal and Installation Procedure for CVT Unit Connector ................................................................ 9 . REMOVAL ............................................................ 9 . INSTALLATION .................................................. 10 . Precautions ........................................................... 10 . Service Notice or Precautions ................................11 . OBD-II SELF-DIAGNOSIS ..................................11 . Wiring Diagrams and Trouble Diagnosis ................11 . PREPARATION ........................................................ 12 . Special Service Tools ............................................ 12 . Commercial Service Tools ..................................... 13 . CVT FLUID .............................................................. 14 . Checking CVT Fluid .............................................. 14 . Changing CVT Fluid .............................................. 15 . CVT SYSTEM .......................................................... 16 . Cross-Sectional View - RE0F09A ......................... 16 . Control System ...................................................... 17 . Hydraulic Control System ...................................... 18 . TCM Function ........................................................ 19 . CONTROL SYSTEM OUTLINE ......................... 19 . CONTROL SYSTEM DIAGRAM ........................ 19 . CAN Communication ............................................. 20 . SYSTEM DESCRIPTION ................................... 20 . Input/Output Signal of TCM ................................... 20 . Line Pressure and Secondary Pressure Control ... 21 NORMAL CONTROL ......................................... 21 . FEEDBACK CONTROL ..................................... 21 . Shift Control ........................................................... 21 . D POSITION .................................................... 22 . M POSITION .................................................... 22 . DOWNHILL ENGINE BRAKE CONTROL (AUTO ENGINE BRAKE CONTROL) ............................. 22 . ACCELERATION CONTROL ............................. 22 . Lock-up and Select Control ................................... 22 . TORQUE CONVERTER CLUTCH AND SELECT CONTROL VALVE CONTROL ........................... 23 . Control Valve ......................................................... 24 . FUNCTION OF CONTROL VALVE .................... 24 . ON BOARD DIAGNOSTIC (OBD) SYSTEM ........... 25 . Introduction ............................................................ 25 . OBD-II Function for CVT System .......................... 25 . One or Two Trip Detection Logic of OBD-II ........... 25 . ONE TRIP DETECTION LOGIC ........................ 25 . TWO TRIP DETECTION LOGIC ........................ 25 . OBD-II Diagnostic Trouble Code (DTC) ................ 25 . HOW TO READ DTC AND 1ST TRIP DTC ........ 25 . HOW TO ERASE DTC ....................................... 26 . HOW TO ERASE DTC (WITH CONSULT-II) ...... 27 . HOW TO ERASE DTC (WITH GST) .................. 27 . Malfunction Indicator (MI) ...................................... 28 . DESCRIPTION ................................................... 28 . TROUBLE DIAGNOSIS ........................................... 29 . DTC Inspection Priority Chart ................................ 29 . Fail-safe ................................................................. 29 . FAIL-SAFE FUNCTION ...................................... 29 . How to Perform Trouble Diagnosis for Quick and Accurate Repair ..................................................... 30 . INTRODUCTION ................................................ 30 . WORK FLOW ..................................................... 31 . DIAGNOSTIC WORKSHEET ............................. 32 . CVT Electrical Parts Location ................................ 35 . Circuit Diagram ...................................................... 36 . Inspections Before Trouble Diagnosis ................... 37 .
CVT-1
CVT FLUID CHECK ........................................... 37 . STALL TEST ....................................................... 37 . LINE PRESSURE TEST ..................................... 39 . Road Test .............................................................. 41 . DESCRIPTION ................................................... 41 . CONSULT-II SETTING PROCEDURE ............... 41 . Check Before Engine Is Started ............................. 44 . Check at Idle .......................................................... 44 . Cruise Test ............................................................. 47 . Vehicle Speed at Which Gear Shifting Occurs ...... 49 . TCM Input/Output Signal Reference Values .......... 50 . TCM TERMINAL CONNECTOR LAYOUT ......... 50 . TCM INSPECTION TABLE ................................. 50 . CONSULT-II Function (TRANSMISSION) ............. 53 . FUNCTION ......................................................... 53 . CONSULT-II REFERENCE VALUE .................... 53 . CONSULT-II SETTING PROCEDURE ............... 55 . WORK SUPPORT MODE .................................. 56 . SELF-DIAGNOSTIC RESULT MODE ................ 58 . DATA MONITOR MODE ..................................... 61 . CAN DIAGNOSTIC SUPPORT MONITOR MODE ................................................................. 63 . Diagnostic Procedure Without CONSULT-II .......... 64 . OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST) ........................................................ 64 . DTC U1000 CAN COMMUNICATION LINE ............. 65 . Description ............................................................. 65 . On Board Diagnosis Logic ..................................... 65 . Possible Cause ...................................................... 65 . DTC Confirmation Procedure ................................ 65 . WITH CONSULT-II ............................................. 65 . WITH GST .......................................................... 65 . Wiring Diagram CVT CAN ............................ 66 . Diagnostic Procedure ............................................ 67 . DTC P0615 START SIGNAL CIRCUIT .................... 68 . Description ............................................................. 68 . CONSULT-II Reference Value ............................... 68 . On Board Diagnosis Logic ..................................... 68 . Possible Cause ...................................................... 68 . DTC Confirmation Procedure ................................ 68 . WITH CONSULT-II ............................................. 68 . Wiring Diagram CVT STSIG ......................... 69 . Diagnostic Procedure ............................................ 70 . DTC P0703 STOP LAMP SWITCH CIRCUIT .......... 72 . Description ............................................................. 72 . CONSULT-II Reference Value ............................... 72 . On Board Diagnosis Logic ..................................... 72 . Possible Cause ...................................................... 72 . DTC Confirmation Procedure ................................ 72 . WITH CONSULT-II ............................................. 72 . Diagnostic Procedure ............................................ 73 . DTC P0705 PARK/NEUTRAL POSITION SWITCH... 74 Description ............................................................. 74 . CONSULT-II Reference Value ............................... 74 . On Board Diagnosis Logic ..................................... 74 . Possible Cause ...................................................... 74 . DTC Confirmation Procedure ................................ 74 . WITH CONSULT-II ............................................. 75 . WITH GST .......................................................... 75 .
Wiring Diagram CVT PNP/SW ......................76 . Diagnostic Procedure .............................................78 . Component Inspection ...........................................80 . PNP SWITCH .....................................................80 . DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT ...................................................................81 . Description .............................................................81 . CONSULT-II Reference Value ................................81 . On Board Diagnosis Logic .....................................81 . Possible Cause ......................................................81 . DTC Confirmation Procedure .................................81 . WITH CONSULT-II ..............................................81 . WITH GST ..........................................................81 . Wiring Diagram CVT FTS .............................82 . Diagnostic Procedure .............................................83 . Component Inspection ...........................................85 . CVT FLUID TEMPERATURE SENSOR .............85 . DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR) ....................................................86 . Description .............................................................86 . CONSULT-II Reference Value ................................86 . On Board Diagnosis Logic .....................................86 . Possible Cause ......................................................86 . DTC Confirmation Procedure .................................86 . WITH CONSULT-II ..............................................86 . WITH GST ..........................................................86 . Wiring Diagram CVT PRSCVT .....................87 . Diagnostic Procedure .............................................88 . DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR) ....................................91 . Description .............................................................91 . CONSULT-II Reference Value ................................91 . On Board Diagnosis Logic .....................................91 . Possible Cause ......................................................91 . DTC Confirmation Procedure .................................91 . WITH CONSULT-II ..............................................91 . WITH GST ..........................................................91 . Wiring Diagram CVT SESCVT .....................92 . Diagnostic Procedure .............................................93 . DTC P0725 ENGINE SPEED SIGNAL .....................97 . Description .............................................................97 . CONSULT-II Reference Value ................................97 . On Board Diagnosis Logic .....................................97 . Possible Cause ......................................................97 . DTC Confirmation Procedure .................................97 . WITH CONSULT-II ..............................................97 . Diagnostic Procedure .............................................97 . DTC P0730 BELT DAMAGE ....................................99 . Description .............................................................99 . CONSULT-II Reference Value ................................99 . On Board Diagnosis Logic .....................................99 . Possible Cause ......................................................99 . DTC Confirmation Procedure .................................99 . WITH CONSULT-II ..............................................99 . Diagnostic Procedure ........................................... 100 . DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE ................................................. 101 . Description ........................................................... 101 . CONSULT-II Reference Value .............................. 101 .
CVT-2
On Board Diagnosis Logic .................................. 101 . Possible Cause ................................................... 101 . DTC Confirmation Procedure .............................. 101 . WITH CONSULT-II ........................................... 101 . WITH GST ........................................................ 101 . Wiring Diagram CVT TCV .......................... 102 . Diagnostic Procedure .......................................... 103 . Component Inspection ........................................ 105 . TORQUE CONVERTER CLUTCH SOLENOID VALVE .............................................................. 105 . DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP). 106 Description .......................................................... 106 . CONSULT-II Reference Value ............................. 106 . On Board Diagnosis Logic .................................. 106 . Possible Cause ................................................... 106 . DTC Confirmation Procedure .............................. 106 . WITH CONSULT-II ........................................... 106 . WITH GST ........................................................ 106 . Diagnostic Procedure .......................................... 107 . DTC P0745 LINE PRESSURE SOLENOID VALVE 109 . Description .......................................................... 109 . CONSULT-II Reference Value ............................. 109 . On Board Diagnosis Logic .................................. 109 . Possible Cause ................................................... 109 . DTC Confirmation Procedure .............................. 109 . WITH CONSULT-II ........................................... 109 . WITH GST ........................................................ 109 . Wiring Diagram CVT LPSV .........................110 . Diagnostic Procedure ........................................... 111 . Component Inspection .........................................113 . PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) ...........113 . DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE) ....................................................................114 . Description ...........................................................114 . CONSULT-II Reference Value ..............................114 . On Board Diagnosis Logic ...................................114 . Possible Cause ....................................................114 . DTC Confirmation Procedure ...............................114 . WITH CONSULT-II ............................................114 . WITH GST .........................................................114 . Diagnostic Procedure ...........................................115 . DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE) ....................................................................117 . Description ...........................................................117 . CONSULT-II Reference Value ..............................117 . On Board Diagnosis Logic ...................................117 . Possible Cause ....................................................117 . DTC Confirmation Procedure ...............................117 . WITH CONSULT-II ............................................117 . WITH GST .........................................................117 . Diagnostic Procedure ...........................................118 . DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE) ................................................................... 120 . Description .......................................................... 120 . CONSULT-II Reference Value ............................. 120 .
On Board Diagnosis Logic ................................... 120 . Possible Cause .................................................... 120 . DTC Confirmation Procedure .............................. 120 . WITH CONSULT-II ........................................... 120 . WITH GST ........................................................ 120 . Wiring Diagram CVT SECPSV ................... 121 . Diagnostic Procedure .......................................... 122 . Component Inspection ......................................... 124 . PRESSURE CONTROL SORENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE) . 124 DTC P0826 MANUAL MODE SWITCH CIRCUIT .. 125 . Description ........................................................... 125 . CONSULT-II Reference Value ............................. 125 . On Board Diagnosis Logic ................................... 125 . Possible Cause .................................................... 125 . DTC Confirmation Procedure .............................. 125 . WITH CONSULT-II ........................................... 125 . Wiring Diagram CVT MMSW (LHD Models). 126 Wiring Diagram CVT MMSW (RHD Models) 128 . Diagnostic Procedure .......................................... 129 . Component Inspection ......................................... 131 . MANUAL MODE SWITCH ............................... 131 . DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR) 132 . Description ........................................................... 132 . CONSULT-II Reference Value ............................. 132 . On Board Diagnosis Logic ................................... 132 . Possible Cause .................................................... 132 . DTC Confirmation Procedure .............................. 132 . WITH CONSULT-II ........................................... 132 . WITH GST ........................................................ 132 . Wiring Diagram CVT SECPS ..................... 133 . Diagnostic Procedure .......................................... 134 . DTC P0841 PRESSURE SENSOR FUNCTION .... 137 . Description ........................................................... 137 . CONSULT-II Reference Value ............................. 137 . On Board Diagnosis Logic ................................... 137 . Possible Cause .................................................... 137 . DTC Confirmation Procedure .............................. 137 . WITH CONSULT-II ........................................... 137 . Diagnostic Procedure .......................................... 138 . DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR). 140 Description ........................................................... 140 . CONSULT-II Reference Value ............................. 140 . On Board Diagnosis Logic ................................... 140 . Possible Cause .................................................... 140 . DTC Confirmation Procedure .............................. 140 . WITH CONSULT-II ........................................... 140 . WITH GST ........................................................ 140 . Wiring Diagram CVT PRIPS ....................... 141 . Diagnostic Procedure .......................................... 142 . DTC P0868 SECONDARY PRESSURE DOWN .... 145 . Description ........................................................... 145 . CONSULT-II Reference Value ............................. 145 . On Board Diagnosis Logic ................................... 145 . Possible Cause .................................................... 145 . DTC Confirmation Procedure .............................. 145 .
CVT
CVT-3
WITH CONSULT-II ........................................... 145 . Diagnostic Procedure .......................................... 146 . DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY) ................................................. 148 . Description ........................................................... 148 . On Board Diagnosis Logic ................................... 148 . Possible Cause .................................................... 148 . DTC Confirmation Procedure .............................. 148 . WITH CONSULT-II ........................................... 148 . Wiring Diagram CVT POWER (LHD Models) 149 . Wiring Diagram CVT POWER (RHD Models) 151 . Diagnostic Procedure .......................................... 152 . DTC P1705 THROTTLE POSITION SENSOR ...... 155 . Description ........................................................... 155 . CONSULT-II Reference Value ............................. 155 . On Board Diagnosis Logic ................................... 155 . Possible Cause .................................................... 155 . DTC Confirmation Procedure .............................. 155 . WITH CONSULT-II ........................................... 155 . Diagnostic Procedure .......................................... 156 . DTC P1722 ESTM VEHICLE SPEED SIGNAL ...... 157 . Description ........................................................... 157 . CONSULT-II Reference Value ............................. 157 . On Board Diagnosis Logic ................................... 157 . Possible Cause .................................................... 157 . DTC Confirmation Procedure .............................. 157 . WITH CONSULT-II ........................................... 157 . Diagnostic Procedure .......................................... 158 . DTC P1723 CVT SPEED SENSOR FUNCTION .... 159 . Description ........................................................... 159 . On Board Diagnosis Logic ................................... 159 . Possible Cause .................................................... 159 . DTC Confirmation Procedure .............................. 159 . WITH CONSULT-II ........................................... 159 . Diagnostic Procedure .......................................... 160 . DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM ................................................................. 161 . Description ........................................................... 161 . On Board Diagnosis Logic ................................... 161 . Possible Cause .................................................... 161 . DTC Confirmation Procedure .............................. 161 . WITH CONSULT-II ........................................... 161 . Diagnostic Procedure .......................................... 162 . DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT ................................................................. 163 . Description ........................................................... 163 . CONSULT-II Reference Value ............................. 163 . On Board Diagnosis Logic ................................... 163 . Possible Cause .................................................... 163 . DTC Confirmation Procedure .............................. 163 . WITH CONSULT-II ........................................... 163 . WITH GST ........................................................ 163 . Wiring Diagram CVT L/USSV ..................... 164 . Diagnostic Procedure .......................................... 165 . Component Inspection ......................................... 167 . LOCK-UP SELECT SOLENOID VALVE ........... 167 . DTC P1745 LINE PRESSURE CONTROL ............ 168 . Description ........................................................... 168 . On Board Diagnosis Logic ................................... 168 .
Possible Cause .................................................... 168 . DTC Confirmation Procedure ............................... 168 . WITH CONSULT-II ............................................ 168 . Diagnostic Procedure ........................................... 168 . DTC P1777 STEP MOTOR - CIRCUIT ................... 169 . Description ........................................................... 169 . CONSULT-II Reference Value .............................. 169 . On Board Diagnosis Logic ................................... 169 . Possible Cause .................................................... 169 . DTC Confirmation Procedure ............................... 169 . WITH CONSULT-II ............................................ 169 . WITH GST ........................................................ 169 . Wiring Diagram CVT STM .......................... 170 . Diagnostic Procedure ........................................... 171 . Component Inspection ......................................... 172 . STEP MOTOR .................................................. 172 . DTC P1778 STEP MOTOR - FUNCTION ............... 173 . Description ........................................................... 173 . CONSULT-II Reference Value .............................. 173 . On Board Diagnosis Logic ................................... 173 . Possible Cause .................................................... 173 . DTC Confirmation Procedure ............................... 173 . WITH CONSULT-II ............................................ 173 . WITH GST ........................................................ 174 . Diagnostic Procedure ........................................... 174 . CVT INDICATOR CIRCUIT ..................................... 175 . Description ........................................................... 175 . CONSULT-II Reference Value .............................. 175 . Diagnostic Procedure ........................................... 175 . CVT INDICATOR SYMPTOM CHART .............. 175 . TROUBLE DIAGNOSIS FOR SYMPTOMS ........... 176 . Wiring Diagram CVT NONDTC (LHD Models).176 Wiring Diagram CVT NONDTC (RHD Models) .180 CVT Indicator Lamp Does Not Come On ............. 184 . SYMPTOM: ....................................................... 184 . DIAGNOSTIC PROCEDURE ............................ 184 . Engine Cannot Be Started in P or N Position .. 186 . SYMPTOM: ....................................................... 186 . DIAGNOSTIC PROCEDURE ............................ 186 . In P Position, Vehicle Moves Forward or Backward When Pushed ...................................................... 187 . SYMPTOM: ....................................................... 187 . DIAGNOSTIC PROCEDURE ............................ 187 . In N Position, Vehicle Moves ............................. 188 . SYMPTOM: ....................................................... 188 . DIAGNOSTIC PROCEDURE ............................ 188 . Large Shock N R Position .......................... 189 . SYMPTOM: ....................................................... 189 . DIAGNOSTIC PROCEDURE ............................ 189 . Vehicle Does Not Creep Backward in R Position.191 SYMPTOM: ....................................................... 191 . DIAGNOSTIC PROCEDURE ............................ 191 . Vehicle Does Not Creep Forward in D Position . 193 SYMPTOM: ....................................................... 193 . DIAGNOSTIC PROCEDURE ............................ 193 . CVT Does Not Shift .............................................. 195 . SYMPTOM: ....................................................... 195 . DIAGNOSTIC PROCEDURE ............................ 195 . Cannot Be Changed to Manual Mode .................. 197 .
CVT-4
SYMPTOM: ...................................................... 197 . DIAGNOSTIC PROCEDURE ........................... 197 . CVT Does Not Shift in Manual Mode .................. 198 . SYMPTOM: ...................................................... 198 . DIAGNOSTIC PROCEDURE ........................... 198 . Vehicle Does Not Decelerate by Engine Brake ... 200 . SYMPTOM: ...................................................... 200 . DIAGNOSTIC PROCEDURE ........................... 200 . SHIFT CONTROL SYSTEM .................................. 202 . Removal and Installation ..................................... 202 . CONTROL DEVICE COMPONENTS .............. 202 . CONTROL CABLE COMPONENTS ................ 203 . REMOVAL ........................................................ 203 . INSTALLATION ................................................ 204 . Adjustment of CVT Position ................................ 204 . Checking of CVT Position ................................... 205 . CVT SHIFT LOCK SYSTEM .................................. 206 . Description .......................................................... 206 . Shift Lock System Electrical Parts Location ........ 206 . Wiring Diagram CVT SHIFT (LHD Models). 207 Wiring Diagram CVT SHIFT (RHD Models). 209 Shift Lock Control Unit Reference Values ............211 . SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT ..................................................211 . SHIFT LOCK CONTROL UNIT INSPECTION TABLE ...............................................................211 . Component Inspection ........................................ 212 . SHIFT LOCK SOLENOID ................................ 212 . DETENTION SWITCH ..................................... 212 . DETENTION SWITCH ..................................... 212 . KEY LOCK SOLENOID .................................... 212 . KEY SWITCH ................................................... 213 . STOP LAMP SWITCH ..................................... 213 . AIR BREATHER HOSE ......................................... 214 . Removal and Installation ..................................... 214 .
DIFFERENTIAL SIDE OIL SEAL ........................... 215 . Removal and Installation ..................................... 215 . COMPONENTS ................................................ 215 . REMOVAL ........................................................ 215 . INSTALLATION ................................................ 216 . CVT FLUID COOLER SYSTEM ............................. 217 . CVT Fluid Cooler Removal and Installation ......... 217 . COMPONENTS ................................................ 217 . REMOVAL ........................................................ 217 . INSTALLATION ................................................ 219 . CVT Fluid Cooler Bypass Valve Removal and Installation .................................................................... 220 . REMOVAL ........................................................ 220 . INSTALLATION ................................................ 221 . CVT Fluid Cooler Valve Removal and Installation. 222 COMPONENTS ................................................ 222 . REMOVAL ........................................................ 223 . INSTALLATION ................................................ 225 . COMPONENT INSPECTION ........................... 225 . TRANSAXLE ASSEMBLY ..................................... 226 . Removal and Installation ..................................... 226 . COMPONENTS ................................................ 226 . REMOVAL ........................................................ 227 . INSPECTION ................................................... 229 . INSTALLATION ................................................ 230 . SERVICE DATA AND SPECIFICATIONS (SDS) ... 232 . General Specifications ......................................... 232 . Vehicle Speed at Which Gear Shifting Occurs .... 232 . Stall Speed .......................................................... 232 . Line Pressure ...................................................... 232 . Solenoid Valves ................................................... 232 . CVT Fluid Temperature Sensor ........................... 233 . Primary Speed Sensor ........................................ 233 . Secondary Speed Sensor .................................... 233 . Removal and Installation ..................................... 233 .
CVT
CVT-5
NOTE: If DTC U1000 CAN COMM CIRCUIT is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000 CAN COMMUNICATION LINE. Refer to CVT-65 .
DTC Items (CONSULT-II screen terms) OBD-II CONSULT-II GST*1 P0744 P0710 U1000 P0715 P0745 P1740 P0705 P0746 P0778 P0776 P1777 P1778 P0740 P0840 P0845 P0720 Except OBD-II CONSULT-II only TRANSMISSION P0744 P0710 P0730 P0703 U1000 P1723 P0725 P1726 P1722 P0715 P1745 P0745 P1740 P0826 P0705 P0841 P0746 P0778 P0776 P0868 P0615 P1777 P1778 P0740 P1701 P1705 P0840 P0845 P0720 CVT-106 CVT-81 CVT-99 CVT-72 CVT-65 CVT-159 CVT-97 CVT-161 CVT-157 CVT-86 CVT-168 CVT-109 CVT-163 CVT-125 CVT-74 CVT-137 CVT-114 CVT-120 CVT-117 CVT-145 CVT-68 CVT-169 CVT-173 CVT-101 CVT-148 CVT-155 CVT-132 CVT-140 CVT-91 Reference page
A/T TCC S/V FNCTN ATF TEMP SEN/CIRC BELT DAMG BRAKE SW/CIRC CAN COMM CIRCUIT CVT SPD SEN/FNCTN ENGINE SPEED SIG ELEC TH CONTROL ESTM VEH SPD SIG INPUT SPD SEN/CIRC L/PRESS CONTROL L/PRESS SOL/CIRC LU-SLCT SOL/CIRC MANUAL MODE SWITCH PNP SW/CIRC PRESS SEN/FNCTN PRS CNT SOL/A FCTN PRS CNT SOL/B CIRC PRS CNT SOL/B FCTN SEC/PRESS DOWN STARTER RELAY/CIRC STEP MOTR CIRC STEP MOTR/FNC TCC SOLENOID/CIRC TCM-POWER SUPPLY TP SEN/CIRC A/T TR PRS SENS/A CIRC TR PRS SENS/B CIRC VEH SPD SEN/CIR AT
CVT-6
NOTE: If DTC U1000 CAN COMM CIRCUIT is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000 CAN COMMUNICATION LINE. Refer to CVT-65 .
DTC OBD-II CONSULT-II GST*1 P0705 P0710 P0715 P0720 P0740 P0744 P0745 P0746 P0776 P0778 P0840 P0845 P1740 P1777 P1778 U1000 Except OBD-II CONSULT-II only TRANSMISSION P0615 P0703 P0705 P0710 P0715 P0720 P0725 P0730 P0740 P0744 P0745 P0746 P0776 P0778 P0826 P0840 P0841 P0845 P0868 P1701 P1705 P1722 P1723 P1726 P1740 P1745 P1777 P1778 U1000 Items (CONSULT-II screen terms) Reference page
CVT
CVT-68 CVT-72 CVT-74 CVT-81 CVT-86 CVT-91 CVT-97 CVT-99 CVT-101 CVT-106 CVT-109 CVT-114 CVT-117 CVT-120 CVT-125 CVT-132 CVT-137 CVT-140 CVT-145 CVT-148 CVT-155 CVT-157 CVT-159 CVT-161 CVT-163 CVT-168 CVT-169 CVT-173 CVT-65
STARTER RELAY/CIRC BRAKE SW/CIRC PNP SW/CIRC ATF TEMP SEN/CIRC INPUT SPD SEN/CIRC VEH SPD SEN/CIR AT ENGINE SPEED SIG BELT DAMG TCC SOLENOID/CIRC A/T TCC S/V FNCTN L/PRESS SOL/CIRC PRS CNT SOL/A FCTN PRS CNT SOL/B FCTN PRS CNT SOL/B CIRC MANUAL MODE SWITCH TR PRS SENS/A CIRC PRESS SEN/FNCTN TR PRS SENS/B CIRC SEC/PRESS DOWN TCM-POWER SUPPLY TP SEN/CIRC A/T ESTM VEH SPD SIG CVT SPD SEN/FNCTN ELEC TH CONTROL LU-SLCT SOL/CIRC L/PRESS CONTROL STEP MOTR CIRC STEP MOTR/FNC CAN COMM CIRCUIT
CVT-7
PRECAUTIONS PRECAUTIONS PFP:00001 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER
ECS00F58
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual. WARNING: q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. q Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
ECS00FNP
The ECM has an on board diagnostic system. It will light up the malfunction indicator (MI) to warn the driver of a malfunction causing emission deterioration. CAUTION: q Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves, etc. will cause the MI to light up. q Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will cause the MI to light up due to the open circuit. (Be sure the connector is free from water, grease, dirt, bent terminals, etc.) q Be sure to route and secure the harnesses properly after work. The interference of the harness with a bracket, etc. may cause the MI to light up due to the short circuit. q Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube may cause the MI to light up due to the malfunction of the fuel injection system, etc. q Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and ECM before returning the vehicle to the customer.
ECS00F5A
CAUTION: q Check if new data (Unit ID) are entered correctly after replacing CVT assembly and erasing data in TCM. (Connect CONSULT-II, and then turn ignition switch OFF.) q When replacing CVT assembly or TCM, refer to the pattern table below and erase the EEPROM in the TCM if necessary.
Not replaced
Replaced
Not required
Replaced
Not replaced
Required
CVT-8
PRECAUTIONS
METHOD FOR ERASING THE EEPROM IN THE TCM
1. 2. 3. 4. 5. 6. 7.
A Connect CONSULT-II to data link connector. Refer to CVT-55, "CONSULT-II SETTING PROCEDURE" . Turn ignition switch ON. Confirm that CONSULT-II is turned ON. Move selector lever to R position. B Touch START (NISSAN BASED VHCL) on CONSULT-II. Select SELF-DIAG RESULTS mode for TRANSMISSION with CONSULT-II. Press the brake pedal and turn the brake switch ON. CVT Press the accelerator pedal (0.5/8 - 4/8 throttle) not to exceed the half, and hold it in the half or less open position. (This will set the closed throttle position signal to OFF and the wide open throttle position signal to OFF.) D 8. Touch ERASE on CONSULT-II, and then touch YES. 9. Wait 3 seconds and then release the accelerator pedal. 10. Turn ignition switch OFF. E
METHOD FOR WRITING DATA FROM THE ROM ASSEMBLY IN THE TRANSAXLE
In the following procedure, the TCM reads data from the ROM assembly and writes it to the EEPROM in the TCM. 1. Erase the EEPROM in the TCM. 2. Move selector lever to P position. 3. Turn ignition switch ON.
F
CHECK METHOD
q q
Standard: About 2 seconds after the ignition switch ON, the CVT indicator lamp lights up for 2 seconds. Non-standard: Even after the ignition switch ON, the CVT indicator lamp does not light up after 2 seconds or illuminates immediately. CAUTION: Perform in the P or N position. Replace the CVT assembly. Replace the TCM.
ECS00F5B
Rotate bayonet ring counterclockwise, pull out CVT unit harness connector upward and remove it.
SCIA2096E
CVT-9
PRECAUTIONS
INSTALLATION
1. Align marking on CVT unit harness connector terminal body with marking on bayonet ring, insert CVT unit harness connector, and then rotate bayonet ring clockwise.
SCIA2097E
2.
Rotate bayonet ring clockwise until marking on CVT unit harness connector terminal body is aligned with the slit on bayonet ring as shown in the figure (correctly fitting condition), install CVT unit harness connector to CVT unit harness connector terminal body.
SCIA2098E
CAUTION: Securely align marking on CVT unit harness connector terminal body with bayonet ring slit. Then, be careful not to make a half fit condition as shown in the figure. q Do not mistake the slit of bayonet ring for other dent portion.
q
SCIA2099E
Precautions
ECS00F5C
NOTE: If any malfunction occurs in the RE0F09A model transaxle, replace the entire transaxle assembly. q Before connecting or disconnecting the TCM harness connector, turn ignition switch OFF and disconnect the battery cable from the negative terminal. Because battery voltage is applied to TCM even if ignition switch is turned OFF.
SEF289H
CVT-10
PRECAUTIONS
q
When connecting or disconnecting pin connectors into or from TCM, take care not to damage pin terminals (bend or break). When connecting pin connectors make sure that there are not any bends or breaks on TCM pin terminal.
CVT
SEF291H
D
q
Before replacing TCM, perform TCM input/output signal inspection and make sure whether TCM functions properly or not. Refer to CVT-50, "TCM INSPECTION TABLE".
G
MEF040DA
q q
After performing each TROUBLE DIAGNOSIS, perform DTC Confirmation Procedure. If the repair is completed the DTC should not be displayed in the DTC Confirmation Procedure. Always use the specified brand of CVT fluid. Refer to MA-14, "Fluids and Lubricants" . Use lint-free paper, not cloth rags, during work. After replacing the CVT fluid, dispose of the waste oil using the methods prescribed by law, ordinance, etc.
SAT652J
ECS00F5D
CVT self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through the blinking pattern of the malfunction indicator (MI). Refer to the table on CVT-58, "Display Items List" for the indicator used to display each self-diagnostic result. q The self-diagnostic results indicated by the MI are automatically stored in both the TCM and ECM memories. Always perform the procedure on CVT-26, "HOW TO ERASE DTC" to complete the repair and avoid unnecessary blinking of the MI. For details of OBD-II, refer to EC-35, "ON BOARD DIAGNOSTIC (OBD) SYSTEM" . q Certain systems and components, especially those related to OBD, may use the new style slidelocking type harness connector. For description and how to disconnect, refer to PG-103, "HARNESS CONNECTOR".
ECS00F5E
CVT-11
ZZA0600D
NT086
NT086
CVT-12
CVT
SCIA2013E
31093CA000 Slinger
SCIA2014E
F
Removing and installing transaxle assembly
31092CA000 Slinger
H
SCIA2015E
Power tool
J
PBIC0190E
CVT-13
Fluid level should be checked with the fluid warmed up to 50 to 80C (122 to 176F). The fluid level check procedure is as follows: 1. Check for fluid leakage. 2. With the engine warmed up, drive the vehicle in an urban area. When ambient temperature is 20C (68F), it takes about 10 minutes for the CVT fluid to warm up to 50 to 80C (122 to 176F). 3. Park the vehicle on a level surface. 4. Apply parking brake firmly. 5. With engine at idle, while depressing brake pedal, move shift selector throughout the entire shift range.
SMA146B
6.
Pull out the CVT fluid level gauge from the CVT fluid charging pipe after pressing the tab on the CVT fluid level gauge to release the lock.
SCIA1933E
7.
Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid level gauge rotating 180 from the originally installed position, then securely push the CVT fluid level gauge until it meets the top end of the CVT fluid charging pipe. CAUTION: When wiping away the CVT fluid level gauge, always use lint-free paper, not a cloth rag.
SCIA1931E
8.
Place the selector lever in P or N and make sure the fluid level is within the specified range. CAUTION: q When reinstalling CVT fluid level gauge, insert it into the CVT fluid charging pipe and rotate it to the original installation position until it is securely locked.
SCIA1932E
CVT-14
CVT FLUID
9. Check CVT fluid condition. q If CVT fluid is very dark or smells burned, check operation of CVT. Flush cooling system after repair of CVT. q If CVT fluid contains frictional material (clutches, bands, etc.), replace radiator and flush cooler line using cleaning solvent and compressed air after repair of CVT. Refer to CO-13, "RADIATOR" .
A
CVT
ATA0022D
D
ECS00F5I
Warm up CVT fluid by driving the vehicle for 10 minutes. : Vehicle front Radiator (2) CVT fluid cooler hose [inlet side (3)] Transaxle assembly (4) Drain CVT fluid from CVT fluid cooler hose [outlet side (1)] and refill with new CVT fluid at CVT fluid charging pipe with the engine running at idle speed. Refill until new CVT fluid comes out from CVT fluid cooler hose (outlet side). About 30 to 50% extra fluid will be required for this procedure. CVT fluid: Genuine NISSAN CVT fluid NS-2 Fluid capacity: Approx. 10.0 (8-3/4 lmp qt) CAUTION: q Use only Genuine NISSAN CVT fluid NS-2. Do not mix with other fluid. q Using CVT fluid other than Genuine NISSAN CVT fluid NS-2 will deteriorate in driveability and CVT durability, and may damage the CVT, which is not covered by the warranty. q When filling CVT fluid, take care not to scatter heat generating parts such as exhaust. q Delete CVT fluid deterioration date with CONSULT-II after changing CVT fluid. Refer to CVT-57, "Check CVT Fluid Deterioration Date" . Check fluid leakage, fluid level and condition.
E
2.
3.
SCIA6088E
4.
CVT-15
SCIA1779E
1. 4. 7.
2. 5. 8.
3. 6. 9.
10. Internal gear 13. Differential case 16. Taper roller bearing 19. Input shaft
11. Secondary pulley 14. Idler gear 17. Output gear 20. Torque converter
CVT-16
CVT
SCIA6757E
CVT-17
SCIA1807E
CVT-18
SCIA6758E
CVT-19
ECS00F5P
Select control X X
Shift control X X X
Lock-up control X X X X
X X X X X X X X X X X X X X X
X X
X X X X X X X X X
Stop lamp switch signal(*1) Primary speed sensor Secondary speed sensor Primary pressure sensor Secondary pressure sensor TCM power supply voltage signal Step motor TCC solenoid valve Output Lock-up select solenoid valve Line pressure solenoid valve Secondary pressure solenoid valve
X X
X X X X X X X X X X X
X X
X X
*1: Input by CAN communications. *2: If these input and output signals are different, the TCM triggers the fail-safe function.
CVT-20
When an input torque signal equivalent to the engine drive force is sent from the ECM to the TCM, the TCM controls the line pressure solenoid valve and secondary pressure solenoid valve. This line pressure solenoid controls the pressure regulator valve as the signal pressure and adjusts the pressure of the operating oil discharged from the oil pump to the line pressure most appropriate to the driving state. Secondary pressure is controlled by decreasing line pressure.
CVT
G
SCIA1846E
NORMAL CONTROL
Optimize the line pressure and secondary pressure, depending on driving conditions, on the basis of the throttle position, the engine speed, the primary pulley (input) revolution speed, the secondary pulley (output) revolution speed, the brake signal, the PNP switch signal, the lock-up signal, the voltage, the target gear ratio, the fluid temperature, and the fluid pressure.
FEEDBACK CONTROL
When controlling the normal fluid pressure or the selected fluid pressure, the secondary pressure can be set more accurately by using the fluid pressure sensor to detect the secondary pressure and controlling the feedback.
Shift Control
K
ECS00F5R
In order to select the gear ratio which can obtain the driving force in accordance with driver's intention and the vehicle condition, TCM monitors the driving conditions, such as the vehicle speed and the throttle position and selects the optimum gear ratio, and determines the gear change steps to the gear ratio. Then send the command to the step motor, and control the flow-in/flow-out of line pressure from the primary pulley to determine the position of the moving-pulley and control the gear ratio.
SCIA6581E
CVT-21
CVT SYSTEM
NOTE: The gear ratio is set for every position separately.
D POSITION
Shifting over all the ranges of gear ratios from the lowest to the highest.
SCIA1953E
M POSITION
When the selector lever is put in the manual shift gate side, the fixed changing gear line is set. By moving the selector lever to + side or side, the manual mode switch is changed over, and shift change like M/T becomes possible following the changing gear set line step by step.
SCIA4582E
ACCELERATION CONTROL
According to vehicle speed and a change of accelerator pedal angle, driver's request for acceleration and driving scene are judged. This function assists improvement in acceleration feeling by making the engine speed proportionate to the vehicle speed. And a shift map which can gain a larger driving force is available for compatibility of mileage with drivability.
ECS00F5S
The torque converter clutch piston in the torque converter is engaged to eliminate torque converter slip to increase power transmission efficiency. The torque converter clutch control valve operation is controlled by the torque converter clutch solenoid valve, which is controlled by a signal from TCM. The torque converter clutch control valve engages or releases the torque converter clutch piston. When shifting between N (P) D (R), torque converter clutch solenoid controls engagement power of forward clutch and reverse brake. The lock-up applied gear range was expanded by locking up the torque converter at a lower vehicle speed than conventional CVT models.
SCIA1958E
CVT-22
CVT SYSTEM
TORQUE CONVERTER CLUTCH AND SELECT CONTROL VALVE CONTROL Lock-up and Select Control System Diagram
A
CVT
SCIA2374E
Lock-up Released
q
In the lock-up released state, the torque converter clutch control valve is set into the unlocked state by the torque converter clutch solenoid and the lock-up apply pressure is drained. In this way, the torque converter clutch piston is not coupled. In the lock-up applied state, the torque converter clutch control valve is set into the locked state by the torque converter clutch solenoid and lock-up apply pressure is generated. In this way, the torque converter clutch piston is pressed and coupled. When shifting between N (P) D (R), optimize the operating pressure on the basis of the throttle position, the engine speed, and the secondary pulley (output) revolution speed to lessen the shift shock.
Lock-up Applied
q
Select Control
q
CVT-23
Function Optimizes the supply pressure for the torque converter depending on driving conditions. Optimizes the discharge pressure from the oil pump depending on driving conditions.
q
Activates or deactivate the lock-up. Lock-up smoothly by opening lock-up operation excessively.
TCC solenoid valve Shift control valve Secondary valve Clutch regulator valve Secondary pressure solenoid valve Line pressure solenoid valve Step motor Manual valve Select control valve Select switch valve Lock-up select solenoid valve
Controls the TCC control valve or select control valve. Controls flow-in/out of line pressure from the primary pulley depending on the stroke difference between the stepping motor and the primary pulley. Controls the line pressure from the secondary pulley depending on operating conditions. Adjusts the clutch operating pressure depending on operating conditions. Controls the secondary valve. Controls the line pressure control valve. Controls the pulley ratio. Transmits the clutch operating pressure to each circuit in accordance with the selected position. Engages forward clutch, reverse brake smoothly depending on select operation. Switches torque converter clutch solenoid valve control pressure use to torque converter clutch control valve or select control valve. Controls the select switch valve.
CVT-24
A
ECS00F5U
The CVT system has two self-diagnostic systems. The first is the emission-related on board diagnostic system (OBD-II) performed by the TCM in combination B with the ECM. The malfunction is indicated by the MI (malfunction indicator) and is stored as a DTC in the ECM memory, and the TCM memory. The second is the TCM original self-diagnosis performed by the TCM. The malfunction is stored in the TCM memory. The detected items are overlapped with OBD-II self-diagnostic items. For detail, refer to CVT-58, CVT "Display Items List" .
ECS00F5V
The ECM provides emission-related on board diagnostic (OBD-II) functions for the CVT system. One function is to receive a signal from the TCM used with OBD-related parts of the CVT system. The signal is sent to the ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a diagnostic result by means of the MI (malfunction indicator) on the instrument panel. Sensors, switches and solenoid valves are used as sensing elements. The MI automatically illuminates in One or Two Trip Detection Logic when a malfunction is sensed in relation to CVT system parts.
ECS00F5W
If a malfunction is sensed during the first test drive, the MI will illuminate and the malfunction will be stored in the ECM memory as a DTC. The TCM is not provided with such a memory function.
ECS00F5X
DTC and 1st trip DTC can be read by the following methods. ( with CONSULT-II or GST) CONSULT-II or GST (Generic Scan Tool) Examples: P0705, P0720 etc. These DTC are prescribed by SAE J2012. (CONSULT-II also displays the malfunctioning component or system.) q 1st trip DTC No. is the same as DTC No. q Output of the diagnostic trouble code indicates that the indicated circuit has a malfunction. However, in case of the Mode II and GST, they do not indicate whether the malfunction is still occurring or occurred in the past and returned to normal. CONSULT-II can identify them as shown below, therefore, CONSULT-II (if available) is recommended. A sample of CONSULT-II display for DTC and 1st trip DTC is shown on the next page. DTC or 1st trip DTC of a malfunction is displayed in SELF-DIAGNOSTIC RESULTS mode for ENGINE with CONSULT-II. Time data indicates how many times the vehicle was driven after the last detection of a DTC.
SCIA4823E
CVT-25
SAT015K
If a 1st trip DTC is stored in the ECM, the time data will be 1t.
SAT016K
Both 1st trip freeze frame data and freeze frame data (along with the DTC) are cleared when the ECM memory is erased.
CVT-26
1st trip freeze frame data System readiness test (SRT) codes Test values
1. 2. 3. 4. 5. 6. 7.
If a DTC is displayed for both ECM and TCM, it is necessary to be erased for both ECM and TCM. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10 seconds and then turn it ON (engine stopped) again. CVT Turn CONSULT-II ON and touch TRANSMISSION. Touch SELF-DIAG RESULTS. D Touch ERASE. (The DTC in the TCM will be erased.) Then touch BACK twice. Touch ENGINE. Touch SELF-DIAG RESULTS. E Touch ERASE. (The DTC in the ECM will be erased.)
F
SCIA6465E
CVT-27
CVT-28
A
ECS00F5Z
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart. B NOTE: If DTC U1000 CAN COMM CIRCUIT is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000 CAN COMMUNICATION LINE. Refer to CVT-65 . CVT
Priority 1 2 U1000 CAN communication line Except above
ECS00F60
Fail-safe
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is an error in a main electronic control input/output signal circuit.
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the CVT to make driving possible.
The shift pattern is changed in accordance with throttle position when an unexpected signal is sent from the output speed sensor (secondary speed sensor) to the TCM. The manual mode position and second position is inhibited, and the transaxle is put in D. The shift pattern is changed in accordance with throttle position and secondary speed (vehicle speed) when an unexpected signal is sent from the input speed sensor (primary speed sensor) to the TCM. The manual mode position and second position is inhibited, and the transaxle is put in D. If an unexpected signal is sent from the PNP switch to the TCM, the transaxle is put in D. If an unexpected signal is sent from the manual mode switch to the TCM, the transaxle is put in D.
PNP Switch
q
If an unexpected signal is sent from the CVT fluid temperature sensor to the TCM, the gear ratio in use before receiving the unexpected signal is maintained or the gear ratio is controlled to keep engine speed under 5,000 rpm. If an unexpected signal is sent from the transmission fluid pressure sensor A (secondary pressure sensor) to the TCM, the secondary pressure feedback control is stopped and the offset value obtained before the non-standard condition occurs is used to control line pressure. If transmission fluid pressure sensor A (secondary pressure sensor) error signal is input to TCM, secondary pressure feedback control stops, but line pressure is controlled normally. If an unexpected signal is sent from the solenoid to the TCM, the pressure control solenoid A (line pressure solenoid) is turned OFF to achieve the maximum fluid pressure. If an unexpected signal is sent from the solenoid to the TCM, the pressure control solenoid B (secondary pressure solenoid) is turned OFF to achieve the maximum fluid pressure. If an unexpected signal is sent from the solenoid to the TCM, the torque converter clutch solenoid is turned OFF to cancel the lock-up.
CVT-29
TROUBLE DIAGNOSIS
Step Motor
q
If an unexpected signal is sent from the step motor to the TCM, the step motor coil phases A through D are all turned OFF to hold the gear ratio used right before the non-standard condition occurred. If an unexpected signal is sent from the solenoid to the TCM, the CVT lock-up select solenoid is turned OFF to cancel the lock-up. Transaxle assembly is protected by limiting the engine torque when the memory back-up power supply (for controlling) from the battery is not supplied to TCM. Normal statues is restored when turning the ignition switch OFF to ON after the normal power supply.
ECS00F61
The TCM receives a signal from the vehicle speed sensor, PNP switch and provides shift control or lock-up control via CVT solenoid valves. The TCM also communicates with the ECM by means of a signal sent from sensing elements used with the OBD-related parts of the CVT system for malfunction-diagnostic purposes. The TCM is capable of diagnosing malfunctioning parts while the ECM can store malfunctions in its memory. Input and output signals must always be correct and stable in the operation of the CVT system. The CVT system must be in good operating condition and be free of valve seizure, solenoid valve malfunction, etc.
SAT631IB
It is much more difficult to diagnose an error that occurs intermittently rather than continuously. Most intermittent errors are caused by poor electric connections or improper wiring. In this case, careful checking of suspected circuits may help prevent the replacement of good parts. A visual check only may not find the cause of the errors. A road test with CONSULT-II (or GST) or a circuit tester connected should be performed. Follow the CVT-31, "WORK FLOW" .
SAT632I
Before undertaking actual checks, take a few minutes to talk with a customer who approaches with a driveability complaint. The customer can supply good information about such errors, especially intermittent ones. Find out what symptoms are present and under what conditions they occur. A DIAGNOSTIC WORKSHEET as shown on the example (Refer to CVT-32 ) should be used. Start your diagnosis by looking for conventional errors first. This will help troubleshoot driveability errors on an electronically controlled engine vehicle. Also check related Service bulletins.
SEF234G
CVT-30
TROUBLE DIAGNOSIS
WORK FLOW
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate. In general, each customer feels differently about a malfunction. It is important to fully understand the symptoms or conditions for a customer complaint. Make good use of the two sheets provided, CVT-32, "Information from Customer" and CVT-32, "Diagnostic Worksheet Chart" , to perform the best troubleshooting possible.
A
SCIA6877E
CVT-31
TROUBLE DIAGNOSIS
DIAGNOSTIC WORKSHEET Information from Customer
KEY POINTS q WHAT..... Vehicle & CVT model q WHEN..... Date, Frequencies q WHERE..... Road conditions q HOW..... Operating conditions, Symptoms
Customer name Trans. Model Malfunction Date Frequency Symptoms MR/MS Model & Year Engine Manuf. Date Continuous Intermittent ( VIN Mileage In Service Date times a day) Particular position)
Vehicle does not move. No shift Lock-up malfunction Shift shock or slip Noise or vibration No pattern select Others (
( Any position
( N D
NR
Lock-up
) Not lit
Continuously lit
CVT-32
TROUBLE DIAGNOSIS
Perform road test. Check before engine is started CVT-184, "CVT Indicator Lamp Does Not Come On" Perform self-diagnosis. Enter checks for detected items. CVT-58 CVT-65, "DTC U1000 CAN COMMUNICATION LINE" . CVT-68, "DTC P0615 START SIGNAL CIRCUIT" . CVT-72, "DTC P0703 STOP LAMP SWITCH CIRCUIT" . CVT-74, "DTC P0705 PARK/NEUTRAL POSITION SWITCH" . CVT-81, "DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT" . CVT-86, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)" . CVT-91, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)" . CVT-97, "DTC P0725 ENGINE SPEED SIGNAL" . CVT-99, "DTC P0730 BELT DAMAGE" . CVT-101, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" . CVT-106, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" . CVT-109, "DTC P0745 LINE PRESSURE SOLENOID VALVE" . CVT-114, "DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE)" . CVT-117, "DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE)" . CVT-120, "DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE)" . CVT-125, "DTC P0826 MANUAL MODE SWITCH CIRCUIT" . CVT-132, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)" . CVT-137, "DTC P0841 PRESSURE SENSOR FUNCTION" . CVT-140, "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)" . CVT-145, "DTC P0868 SECONDARY PRESSURE DOWN" . CVT-148, "DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" . CVT-155, "DTC P1705 THROTTLE POSITION SENSOR" . CVT-157, "DTC P1722 ESTM VEHICLE SPEED SIGNAL" . CVT-159, "DTC P1723 CVT SPEED SENSOR FUNCTION" . CVT-161, "DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM" . CVT-163, "DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT" . CVT-169, "DTC P1777 STEP MOTOR - CIRCUIT" . CVT-173, "DTC P1778 STEP MOTOR - FUNCTION" . Check at idle CVT-186, "Engine Cannot Be Started in P or N Position" . CVT-187, "In P Position, Vehicle Moves Forward or Backward When Pushed" . CVT-188, "In N Position, Vehicle Moves" . CVT-189, "Large Shock N R Position" . CVT-191, "Vehicle Does Not Creep Backward in R Position" . CVT-193, "Vehicle Does Not Creep Forward in D Position" . CVT-44 CVT-41 CVT-44
CVT
4-1.
4-2.
CVT-33
TROUBLE DIAGNOSIS
Cruise test CVT-195, "CVT Does Not Shift" . CVT-197, "Cannot Be Changed to Manual Mode" . CVT-198, "CVT Does Not Shift in Manual Mode" . CVT-200, "Vehicle Does Not Decelerate by Engine Brake" . Perform self-diagnosis. Enter checks for detected items. CVT-58 CVT-65, "DTC U1000 CAN COMMUNICATION LINE" . CVT-68, "DTC P0615 START SIGNAL CIRCUIT" . CVT-72, "DTC P0703 STOP LAMP SWITCH CIRCUIT" . CVT-74, "DTC P0705 PARK/NEUTRAL POSITION SWITCH" . CVT-81, "DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT" . CVT-86, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)" . CVT-91, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)" . CVT-97, "DTC P0725 ENGINE SPEED SIGNAL" . CVT-99, "DTC P0730 BELT DAMAGE" . CVT-101, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" . CVT-106, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" . CVT-109, "DTC P0745 LINE PRESSURE SOLENOID VALVE" . CVT-114, "DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE)" . CVT-117, "DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE)" . CVT-120, "DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE)" . CVT-125, "DTC P0826 MANUAL MODE SWITCH CIRCUIT" . CVT-132, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)" . CVT-137, "DTC P0841 PRESSURE SENSOR FUNCTION" . CVT-140, "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)" . CVT-145, "DTC P0868 SECONDARY PRESSURE DOWN" . CVT-148, "DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" . CVT-155, "DTC P1705 THROTTLE POSITION SENSOR" . CVT-157, "DTC P1722 ESTM VEHICLE SPEED SIGNAL" . CVT-159, "DTC P1723 CVT SPEED SENSOR FUNCTION" . CVT-161, "DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM" . CVT-163, "DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT" . CVT-169, "DTC P1777 STEP MOTOR - CIRCUIT" . CVT-173, "DTC P1778 STEP MOTOR - FUNCTION" . CVT-47
4-3.
5 6 7 8
Inspect each system for items found to be NG in the self-diagnosis and repair or replace the malfunctioning parts. Perform all road tests and enter the checks again for the required items. For any remaining NG items, perform the diagnosis procedure and repair or replace the malfunctioning parts. Erase the results of the self-diagnosis from the TCM. CVT-27, CVT-27 CVT-41
CVT-34
CVT
SCIA6472E
CVT-35
TCWB0135E
CVT-36
Inspect for fluid leakage and check the fluid level. Refer to CVT-14, "Checking CVT Fluid" .
CVT
J
SAT647B
3. 4.
Securely engage the parking brake so that the tires do not turn. Install a tachometer where it can be seen by driver during test. q It is good practice to mark the point of specified engine rpm on indicator.
SCIA1224E
5.
Start engine, apply foot brake, and place selector lever in D position.
SCIA5950E
CVT-37
TROUBLE DIAGNOSIS
6. 7. While holding down the foot brake, gradually press down the accelerator pedal. Quickly read off the stall speed, and then quickly remove your foot from the accelerator pedal. CAUTION: Do not hold down the accelerator pedal for more than 5 seconds during this test. Stall speed: 8. 9. 2,700 - 3,250 rpm
SAT514G
Move the selector lever to the N position. Cool down the CVT fluid. CAUTION: Run the engine at idle for at least one minute. 10. Repeat steps 6 through 9 with selector lever in R position.
R O H L Forward clutch Reverse brake Engine and torque converter one-way clutch Line pressure low Primary pulley Secondary pulley Steel belt
O: Stall speed within standard value position. H: Stall speed is higher than standard value. L: Stall speed is lower than standard value.
CVT-38
TROUBLE DIAGNOSIS
LINE PRESSURE TEST Line Pressure Test Port
A
CVT
D
SCIA1980E
3.
4.
K
SCIA1224E
5.
6.
Start the engine, and then measure the line pressure at both idle and the stall speed. CAUTION: q Keep the brake pedal pressed all the way down during measurement. q When measuring the line pressure at the stall speed, refer to CVT-37, "STALL TEST" . After the measurements are complete, install the oil pressure detection plug and tighten to the specified torque below. : 7.5 Nm (0.77 kg-m, 66 in-lb) CAUTION: q Do not reuse O-ring. q Apply CVT fluid to O-ring.
SAT493G
CVT-39
TROUBLE DIAGNOSIS
Line Pressure
Engine Engine speed At idle speed VQ35DE *1 : Reference values At stall speed Line pressure kPa (kg/cm2 , psi) R, D positions 750 (7.65, 108.8) 5,700 (58.14, 826.5)*1
Oil pump wear Pressure regulator valve or plug sticking or spring fatigue Oil strainer oil pump pressure regulator valve passage oil leak Engine idle speed too low
Idle speed
Possible causes include an oil pressure leak in a passage or device related to the position after the pressure is distributed by the manual valve. Possible causes include a sensor malfunction or malfunction in the line pressure adjustment function. For example
q
Accelerator pedal position signal malfunction CVT fluid temperature sensor malfunction Pressure control solenoid A (line pressure solenoid) malfunction (sticking in OFF state, filter clog, cut line) Pressure regulator valve or plug sticking
High
q q
Possible causes include a sensor malfunction or malfunction in the pressure adjustment function. For example Oil pressure does not rise higher than the oil pressure for idle.
q q q
Accelerator pedal position signal malfunction TCM malfunction Pressure control solenoid A (line pressure solenoid) malfunction (shorting, sticking in ON state) Pressure regulator valve or plug sticking
Stall speed The pressure rises, but does not enter the standard position.
Possible causes include malfunctions in the pressure supply system and malfunction in the pressure adjustment function. For example
q q q
Accelerator pedal position signal malfunction Pressure control solenoid A (line pressure solenoid) malfunction (sticking, filter clog) Pressure regulator valve or plug sticking
Possible causes include an oil pressure leak in a passage or device related to the position after the pressure is distributed by the manual valve.
CVT-40
1. 2. 3.
The purpose of the test is to determine overall performance of CVT and analyze causes of problems. The road test consists of the following three parts: Check Before Engine Is Started CVT-44 . Check at Idle CVT-44 . Cruise Test CVT-47 .
CVT
D
SAT786A
Before road test, familiarize yourself with all test procedures and items to check. Perform tests on all items until specified symptom is found. Troubleshoot items which check out No Good after road test. Refer to CVT-25, "ON BOARD DIAGNOSTIC (OBD) SYSTEM" .
SAT496G
SAT601J
1. 2.
Turn ignition switch OFF. Connect CONSULT-II and CONSULT-II CONVERSTER to data link connector, which is located in instrument driver lower panel on driver side.
PBIB0196E
CVT-41
TROUBLE DIAGNOSIS
3. 4. Turn ignition switch ON. Touch START (NISSAN BASED VHCL).
SAIA0450E
5.
Touch TRANSMISSION. If TRANSMISSION is not indicated, go to GI-35, "CONSULT-II Data Link Connector (DLC) Circuit" .
SCIA4825E
6.
SCIA5492E
7. 8. 9.
Touch MAIN SIGNALS to set recording condition. See Numerical Display, Barchart Display or Line Graph Display. Touch START.
SCIA5493E
10. When performing cruise test. Refer to CVT-47, "Cruise Test" . 11. After finishing cruise test part, touch RECORD.
SCIA4584E
CVT-42
TROUBLE DIAGNOSIS
12. Touch STORE.
A
CVT
SCIA4492E
G
SCIA4493E
SCIA4492E
15. Touch PRINT. 16. Check the monitor data printed out.
SCIA4494E
CVT-43
SCIA6684E
Check at Idle
ECS00F68
CVT-44
TROUBLE DIAGNOSIS
CVT
D
SCIA5947E
4. Push vehicle forward or backward. 5. Apply parking brake. Does vehicle move when it is pushed forward or backward? YES >> Mark the box In P Position, Vehicle Moves Forward or Backward When Pushed on the CVT-32, "DIAGNOSTIC WORKSHEET" . Continue Road Test. NO >> GO TO 4.
SAT796A
CVT-45
TROUBLE DIAGNOSIS
SAT797A
2. Move selector lever to R position. Is there large shock when changing from N to R position? YES >> Mark the box Large shock N R Position on the CVT-32, "DIAGNOSTIC WORKSHEET" . Continue Road Test. NO >> GO TO 6.
SCIA5949E
SAT799A
SCIA5950E
CVT-46
CVT
E
SCIA5947E
5.
I
SCIA5950E
6.
Accelerate vehicle to 2/8-way throttle depressing accelerator pedal constantly. Read vehicle speed and engine speed. Refer to CVT-49, "Vehicle Speed at Which Gear Shifting Occurs" . OK or NG OK >> GO TO 2. NG >> Mark the box of CVT Does Not Shift on the CVT-32, "DIAGNOSTIC WORKSHEET" . Continue Road Test.
SCIA6644E
CVT-47
TROUBLE DIAGNOSIS
SCIA5950E
3.
Read vehicle speed and engine speed. Refer to CVT-49, "Vehicle Speed at Which Gear Shifting Occurs" . OK or NG OK >> GO TO 3. NG >> Mark the box of CVT Does Not Shift on the CVT-32, "DIAGNOSTIC WORKSHEET" . Continue Road Test.
SCIA4366E
SCIA5953E
CVT-48
TROUBLE DIAGNOSIS
CVT
ECS00F6A
J
3,900 - 5,300 1,300 - 2,100
CAUTION: Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
CVT-49
SCIA0495E
W/B
4 5 6 8
Selector lever in P, N positions. Wait at least for 5 seconds with the selector lever in R, D positions. Selector lever in R position. Selector lever in other positions.
10 Y Power supply 11 G/R Step motor A Within 2 seconds after ignition switch ON, the time measurement by using the pulse width measurement function (Hi level) of CONSULTII.*1 CAUTION: Connect the diagnosis data link cable to the vehicle diagnosis connector. *1: A circuit tester cannot be used to test this item.
Battery voltage
0V 30.0 msec
12
O/B
Step motor B
10.0 msec
13 14 15
CVT-50
TROUBLE DIAGNOSIS
Terminal Wire color Item Condition Data (Approx.)
19 Y Power supply 20 R Step motor C Within 2 seconds after ignition switch ON, the time measurement by using the pulse width measurement function (Hi level) of CONSULTII.*1 CAUTION: Connect the diagnosis data link cable to the vehicle diagnosis connector. *1: A circuit tester cannot be used to test this item. Selector lever in N, Ppositions. Selector lever in other positions. 24 G/O Starter relay 25 27 B BR/W Ground PNP switch 1 Selector lever in P position. 28 Y/R G*1 LG/R*2 Power supply (memory back-up) Output speed sensor (Secondary speed sensor) Always Always Selector lever in R, N and D positions.
Battery voltage
B
0V
CVT
30.0 msec
D
10.0 msec
21
R/G
Step motor D
E
Battery voltage 0V
29
300 Hz 0V 8.0V - Battery voltage 0V 10.0V - Battery voltage 0V 8.0V - Battery voltage 0V 10.0V - Battery voltage
32
GR
34
P/B
PNP switch 2
35
P/L
PNP switch 3 Selector lever in P, R and N positions. Selector lever in R, D positions. PNP switch 4 Selector lever in P, N positions.
36
G*1 G/O*2
37
V/W
and
N position idle
0.8V
38
LG
600 Hz
CVT-51
TROUBLE DIAGNOSIS
Terminal Wire color Item Condition Data (Approx.)
41
V/O
and
N position idle
0.7 - 3.5V
42
W/R
Sensor ground
Always
0V 4.5 - 5.5V
46
L/O
Sensor power When CVT fluid temperature is 20C (68F) When CVT fluid temperature is 80C (176F) Always 0V 2.0V 1.0V 0V
47 48
*1
V B
*2:
CVT-52
FUNCTION
Diagnostic test mode Work support Self-diagnostic results Data monitor CAN diagnostic support monitor CALIB data Function test ECU part number Function This mode enables a technician to adjust some devices faster and more accurately by following the indications on CONSULT-II. Self-diagnostic results can be read and erased quickly. Input/Output data in the TCM can be read. The results of transmit/receive diagnosis of CAN communication can be read. Characteristic information for TCM and CVT assembly can be read. Do not use, but displayed. Performed by CONSULT-II instead of a technician to determine whether each system is OK or NG. TCM part number can be read. Reference page CVT-56 CVT-58 CVT-61 CVT-63
CVT
M
0.0/8 - 8.0/8 0.5 - 0.9MPa 0.3 - 0.9MPa -20 step - 190 step 0.0A 0.7A 0.8A 0.0A 0.8 - 0.0A 0.0A 0.6 - 0.7A
CVT-53
TROUBLE DIAGNOSIS
Item name SOLMON2 Condition N position idle When stalled N position idle SOLMON3 When stalled Selector lever in D position INH SW3M Selector lever in P, R and N positions Selector lever in R, D positions INH SW4 Selector lever in P, N positions Selector lever in D position INH SW3 Selector lever in P, R and N positions Selector lever in N, D positions INH SW2 Selector lever in P, R positions Selector lever in R, N and D positions INH SW1 Selector lever in P position Depressed brake pedal BRAKE SW Released brake pedal Fully depressed accelerator pedal FULL SW Released accelerator pedal Released accelerator pedal IDLE SW Fully depressed accelerator pedal Select lever: - side DOWNLVR Other than the above Select lever: + side UPLVR Other than the above Manual shift gate position (neutral, +side, -side) NON MMODE Other than the above Manual shift gate position (neutral) MMODE SMCOIL D SMCOIL C SMCOIL B SMCOIL A Selector lever in P, N positions LUSEL SOL OUT Wait at least for 5 seconds with the selector lever in R or D position Selector lever in P, N positions Selector lever in other positions STRTR RLY MON Selector lever in P, N positions Selector lever in other positions VDC ON ESP operate Other conditions TCS ON TCS operate Other conditions ABS ON ABS operate Other conditions ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF During driving Changes ON OFF. Other than the above Display value (Approx.) 0.8A 0.3 - 0.6A 0.6 - 0.7A 0.4 - 0.6A ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF
CVT-54
TROUBLE DIAGNOSIS
Item name Condition Selector lever in N or P position RANGE Selector lever in R position Selector lever in D position M GEAR POS During driving Display value (Approx.) NP R D 1, 2, 3, 4, 5, 6
CVT
G
PBIB0196E
3. 4.
Turn ignition switch ON. (Do not start engine.) Touch START (NISSAN BASED VHCL).
SAIA0450E
5.
Touch TRANSMISSION. If TRANSMISSION is not indicated, go to GI-35, "CONSULT-II Data Link Connector (DLC) Circuit" .
SCIA4825E
CVT-55
TROUBLE DIAGNOSIS
6. Perform each diagnostic test mode according to each service procedure.
SCIA5492E
SCIA5492E
3.
SCIA4287E
4.
Touch START.
SCIA4288E
CVT-56
TROUBLE DIAGNOSIS
5. Set ENGINE BRAKE LEVEL by touching UP or DOWN. ENGINE BRAKE LEVEL 0: Initial set value (Engine brake level control is activated) OFF: Engine brake level control is deactivated. 6.
A
Turn ignition switch OFF, wait at least 5 seconds and then turn CVT ignition switch ON. 7. Engine brake level set is completed. SAT934J CAUTION: D Mode of +1 0 -1 -2 OFF can be selected by pressing the UP DOWN on CONSULT-II screen. However, do not select mode other than 0 and OFF. If the +1 or -1 or -2 is selected, that might cause the irregular driveability. E Check CVT Fluid Deterioration Date 1. 2. Perform CONSULT-II SETTING PROCEDURE. Refer to CVT55, "CONSULT-II SETTING PROCEDURE" . Touch WORK SUPPORT.
H
SCIA5492E
3.
SCIA4287E
4.
Check CVTF DETERIORATION DATE CVTF DETERIORATION DATE More than 210000: It is necessary to change CVT fluid. Less than 210000: It is not necessary to change CVT fluid.
M
SCIA4289E
CVT-57
TROUBLE DIAGNOSIS
CAUTION: Touch CLEAR after changing CVT fluid, and then erase CVTF DETERIORATION DATE.
SCIA4290E
Operation Procedure
1. 2. Perform CONSULT-II SETTING PROCEDURE. Refer to CVT55, "CONSULT-II SETTING PROCEDURE" . Touch SELF-DIAG RESULTS. Display shows malfunction experienced since the last erasing operation.
SCIA5492E
CAN COMM CIRCUIT STARTER RELAY/ CIRC BRAKE SW/CIRC PNP SW/CIRC
q q
When a malfunction is detected in CAN communications If this signal is ON other than in P or N position, this is judged to be a malfunction. (And if it is OFF in P or N position, this is judged to be a malfunction too.) When the brake switch does not switch to ON or OFF PNP switch 1-4 signals input with impossible pattern PNP switch 3 monitor terminal open or short circuit During running, the CVT fluid temperature sensor signal voltage is excessively high or low Input speed sensor (primary speed sensor) signal is not input due to an open circuit. An unexpected signal is input when vehicle is being driven. Signal from vehicle speed sensor CVT [Output speed sensor (Secondary speed sensor)] not input due to open or short circuit Unexpected signal input during running
CVT-65
P0615
CVT-68
q q q
P0705 P0710
P0715
P0715
CVT-86
P0720
P0720
CVT-91
CVT-58
TROUBLE DIAGNOSIS
TCM selfdiagnosis Items (CONSULTII screen terms) Malfunction is detected when... TRANSMISSION with CONSULT-II P0725 P0730 P0740 OBD-II (DTC) MI*1, ENGINE with CONSULT-II or GST P0740 Reference page
B
CVT-97
ENGINE SPEED SIG BELT DAMG TCC SOLENOID/ CIRC A/T TCC S/V FNCTN
TCM does not receive the CAN communication signal from the ECM. Unexpected gear ratio detected Normal voltage not applied to solenoid due to open or short circuit CVT cannot perform lock-up even if electrical circuit is good. TCM detects as irregular by comparing difference value with slip rotation. Normal voltage not applied to solenoid due to open or short circuit TCM detects as irregular by comparing target value with monitor value. Unexpected gear ratio was detected in the LOW side due to excessively low line pressure. Secondary pressure is too high or too low compared with the commanded value while driving. Normal voltage not applied to solenoid due to cut line, short, or the like TCM detects as irregular by comparing target value with monitor value. When an impossible pattern of switch signals is detected, a malfunction is detected. Signal voltage of the transmission fluid pressure sensor A (secondary pressure sensor) is too high or too low while driving. Correlation between the values of the transmission fluid pressure sensor A (secondary pressure sensor) and the transmission fluid pressure sensor B (primary pressure sensor) is out of specification. Signal voltage of the transmission fluid pressure sensor B (primary pressure sensor) is too high or too low while driving. Secondary fluid pressure is too low compared with the commanded value while driving. When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diagnosis memory function stops This is not a malfunction message (Whenever shutting OFF a power supply to the TCM, this message appears on the screen.) TCM does not receive the proper accelerator pedal position signals (input by CAN communication) from ECM. CAN communication with the ABS actuator and the electric unit (control unit) is malfunctioning. There is a great difference between the vehicle speed signal from the ABS actuator and the electric unit (control unit), and the vehicle speed sensor signal.
CVT
CVT-99 CVT-101
q q
P0744
P0744
CVT-106
L/PRESS SOL/ CIRC PRS CNT SOL/A FCTN PRS CNT SOL/B FCTN PRS CNT SOL/B CIRC MANUAL MODE SWITCH TR PRS SENS/A CIRC
P0745
P0745
CVT-109
P0746 P0776
P0746 P0776
CVT-114 CVT-117
H
P0778 P0778 CVT-120
I
P0826 CVT-125
J
P0840 P0840 CVT-132
K
P0841 CVT-137
L
P0845 P0845 CVT-140
M
P0868 CVT-145
TCM-POWER SUPPLY
P1701
CVT-148
TP SEN/CIRC A/T
P1705
CVT-155
P1722
CVT-157
CVT-59
TROUBLE DIAGNOSIS
TCM selfdiagnosis Items (CONSULTII screen terms) Malfunction is detected when... TRANSMISSION with CONSULT-II OBD-II (DTC) MI*1, ENGINE with CONSULT-II or GST Reference page
A rotation sensor error is detected because the gear does not change in accordance with the position of the stepping motor. CAUTION: One of the P0720 VEH SPD SEN/CIR AT, the P0715 INPUT SPD SEN/CIRC or the P0725 ENGINE SPEED SIG is displayed with the DTC at the same time. P1723 CVT-159
ELEC TH CONTROL LU-SLCT SOL/ CIRC L/PRESS CONTROL STEP MOTR CIRC STEP MOTR/FNC NO DTC IS DETECTED: FURTHER TESTING MAY BE REQUIRED
The electronically controlled throttle for ECM is malfunctioning. Normal voltage not applied to solenoid due to cut line, short, or the like TCM detects as irregular by comparing target value with monitor value. TCM detects the unexpected line pressure. Each coil of the step motor is not energized properly due to an open or a short. There is a great difference between the number of steps for the stepping motor and for the actual gear ratio.
P1726
CVT-161
P1740
P1740
CVT-163
q q
P1777 P1778
SCIA5492E
3.
SCIA4614E
CVT-60
TROUBLE DIAGNOSIS
DATA MONITOR MODE Operation Procedure
1. 2. Perform CONSULT-II SETTING PROCEDURE. Refer to CVT55, "CONSULT-II SETTING PROCEDURE" . Touch DATA MONITOR. NOTE: When malfunction is detected, CONSULT-II performs REAL-TIME DIAGNOSIS. Also, any malfunction detected while in this mode will be displayed at real time.
A
CVT
D
SCIA5492E
G
Output speed sensor (secondary speed sensor).
VSP SENSOR (km/h) ESTM VSP SIG (km/h) PRI SPEED SEN (rpm) ENG SPEED SIG (rpm) SEC HYDR SEN (V) PRI HYDR SEN (V) ATF TEMP SEN (V) VIGN SEN (V) VEHICLE SPEED (km/h) PRI SPEED (rpm) SEC SPEED (rpm) ENG SPEED (rpm) SLIP REV (rpm) GEAR RATIO G SPEED (G)
TRQ RTO SEC PRESS (MPa) PRI PRESS (MPa) ATF TEMP DSR REV (rpm) DGEAR RATIO
X X X
CVT-61
TROUBLE DIAGNOSIS
Monitor item selection Monitored item (Unit) ECU INPUT SIGNALS X X X X X X X X X X X X X X X X X X MAIN SIGNALS X X X X X X X X X Signal input with CAN communications IDLE SW (ON/OFF) SPORT MODE SW (ON/OFF) STRDWNSW (ON/OFF) STRUPSW (ON/OFF) DOWNLVR (ON/OFF) UPLVR (ON/OFF) NON MMODE (ON/OFF) MMODE (ON/OFF) INDLRNG (ON/OFF) INDDRNG (ON/OFF) INDNRNG (ON/OFF) INDRRNG (ON/OFF) INDPRNG (ON/OFF) CVTLAMP (ON/OFF) X X D position indicator output N position indicator output R position indicator output P position indicator output Not mounted but displayed. Torque converter clutch solenoid valve output current Pressure control solenoid valve A (line pressure solenoid valve) output current Pressure control solenoid valve B (secondary pressure solenoid valve) output current Torque converter clutch solenoid valve monitor current Pressure control solenoid valve A (line pressure solenoid valve) monitor current Pressure control solenoid valve B (secondary pressure solenoid valve) monitor current PNP switch 3 ON-OFF status monitor PNP switch 4 ON-OFF status PNP switch 3 ON-OFF status PNP switch 2 ON-OFF status PNP switch 1 ON-OFF status Stop lamp switch SELECTION FROM MENU Remarks
DSTM STEP (step) STM STEP (step) LU PRS (MPa) LINE PRS (MPa) TGT SEC PRESS (MPa) ISOLT1 (A) ISOLT2 (A) ISOLT3 (A) SOLMON1 (A) SOLMON2 (A) SOLMON3 (A) INH SW3M (ON/OFF) INH SW4 (ON/OFF) INH SW3 (ON/OFF) INH SW2 (ON/OFF) INH SW1 (ON/OFF) BRAKE SW (ON/OFF) FULL SW (ON/OFF)
CVT-62
TROUBLE DIAGNOSIS
Monitor item selection Monitored item (Unit) ECU INPUT SIGNALS X X X X MAIN SIGNALS X X X The value measured by the pulse probe is displayed. Displays the value measured by the voltage probe. Not mounted but displayed. Indicates position is recognized by TCM. Indicates a specific value required for control when fail-safe function is activated. Starter relay ESP (Electronic Stability Program) Starter relay Step motor coil D energizing status Step motor coil C energizing status SELECTION FROM MENU
A
Remarks
B
Not mounted but displayed.
SPORT MODE IND (ON/OFF) MMODE IND (ON/OFF) SMCOIL D (ON/OFF) SMCOIL C (ON/OFF) SMCOIL B (ON/OFF) SMCOIL A (ON/OFF) LUSEL SOL OUT (ON/OFF) REV LAMP (ON/OFF) STRTR RLY OUT (ON/OFF) LUSEL SOL MON (ON/OFF) STRTR RLY MON (ON/OFF) VDC ON (ON/OFF) TCS ON (ON/OFF) ABS ON (ON/OFF) ACC ON (ON/OFF) RANGE M GEAR POS Voltage (V) Frequency (Hz) DUTY-HI (high) (%) DUTY-LOW (low) (%) PLS WIDTH-HI (ms) PLS WIDTH-LOW (ms)
CVT
D
Step motor coil B energizing status Step motor coil A energizing status
SCIA5492E
CVT-63
CVT-64
DTC U1000 CAN COMMUNICATION LINE DTC U1000 CAN COMMUNICATION LINE Description
PFP:23710
A
ECS00F6E
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent malfunction detection ability. B Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission CVT with less wiring. Each control unit transmits/receives data but selectively reads required data only.
ECS00F6F
This is an OBD-II self-diagnostic item. Diagnostic trouble code U1000 CAN COMM CIRCUIT with CONSULT-II is detected when TCM cannot communicate to other control units.
ECS00F6G
Possible Cause
Harness or connectors (CAN communication line is open or shorted.)
F
ECS00F6H
NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and wait for at least 6 seconds. If DTC is detected, go to CVT-67, "Diagnostic Procedure" .
I
SCIA4825E
WITH GST
Follow the procedure WITH CONSULT-II.
M
CVT-65
TCWB0136E
CVT-66
A
Item Condition Data (Approx.)
ECS00F6J
Diagnostic Procedure
CVT
G
SCIA5982E
CVT-67
DTC P0615 START SIGNAL CIRCUIT DTC P0615 START SIGNAL CIRCUIT Description
q q q
PFP:25230
ECS00F6K
TCM controls starter relay in IPDM E/R. TCM switches starter relay ON at P or N position and allows to crank engine. Then it prohibits cranking other than at P or N position.
ECS00F6L
ECS00F6M
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0615 STARTER RELAY/CIRC with CONSULT-II is detected when starter relay switched ON other than at P or N position. (Or when switched OFF at P or N position).
ECS00F6N
Possible Cause
q
Harness or connectors (Starter relay and TCM circuit is open or shorted.) Starter relay
ECS00F6O
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. 5. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine. Drive vehicle for at least 2 consecutive seconds. If DTC is detected, go to CVT-70, "Diagnostic Procedure" .
SCIA4825E
CVT-68
CVT
TCWB0137E
CVT-69
Diagnostic Procedure
ON OFF
Without CONSULT-II 1. Turn ignition switch ON. (Do not start engine.) 2. Check voltage between the TCM connector terminal and ground.
Terminal Item Starter relay Condition Selector lever in N, P positions. Selector lever in other positions. Data (Approx.) Battery voltage 0V
24
OK or NG OK >> GO TO 3. NG >> GO TO 2.
SCIA2022E
CVT-70
3. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-68, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 4.
4. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT
CVT-71
DTC P0703 STOP LAMP SWITCH CIRCUIT DTC P0703 STOP LAMP SWITCH CIRCUIT Description
PFP:25320
ECS00F6R
ON, OFF status of the stop lamp switch is sent via the CAN communication from the unified meter and A/C amp to TCM using the signal.
ECS00F6S
ECS00F6T
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0703 BRAKE SW/CIRC with CONSULT-II is detected when the stop lamp switch does not switch to ON and OFF. The stop lamp switch does not switch to ON and OFF.
ECS00F6U
Possible Cause
q
Harness or connectors (Stop lamp switch, and unified meter and A/C amp circuit are open or shorted.) (CAN communication line is open or shorted.) Stop lamp switch
ECS00F6V
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. 5. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine. Start vehicle for at least 3 consecutive seconds. If DTC is detected, go to CVT-73, "Diagnostic Procedure" .
SCIA4825E
CVT-72
CVT
G
SCIA2275E
L
SCIA3700E
Check stop lamp switch after adjusting brake pedal refer to BR-6, "BRAKE PEDAL" . OK or NG OK >> Check the following. If NG, repair or replace damaged parts. q Harness for short or open between battery and stop lamp switch. q Harness for short or open between stop lamp switch and unified meter and A/C amp. NG >> Repair or replace the stop lamp switch.
CVT-73
DTC P0705 PARK/NEUTRAL POSITION SWITCH DTC P0705 PARK/NEUTRAL POSITION SWITCH Description
q q
PFP:32006
ECS00F6X
The park/neutral position (PNP) switch includes 4 transmission position switches. TCM judges the selector lever position by the PNP switch signal.
Shift position P R N D PNP switch 1 OFF ON ON ON PNP switch 2 OFF OFF ON ON PNP switch 3 OFF OFF OFF ON PNP switch 4 OFF ON OFF ON PNP switch 3 (monitor) OFF OFF OFF ON
ECS00F6Y
ECS00F6Z
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0705 PNP SW/CIRC with CONSULT-II is detected under the following conditions. When TCM does not receive the correct voltage signal from the PNP switches 1, 2, 3 and 4 based on the gear position. When the signal from monitor terminal of PNP switch 3 is different from PNP switch 3.
ECS00F70
Possible Cause
q
q q
Harness or connectors [Park/neutral position (PNP) switches 1, 2, 3, 4 and TCM circuit is open or shorted.] Park/neutral position (PNP) switches 1, 2, 3 and 4 Park/neutral position (PNP) switch 3 monitor terminal is open or shorted
ECS00F71
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
CVT-74
CVT
5.
WITH GST
Follow the procedure WITH CONSULT-II.
E
CVT-75
TCWB0138E
CVT-76
CVT
36
*1: *2
G*1 G/O*2
LHD models.
: RHD models.
CVT-77
1.
1. 2.
With CONSULT-II Turn ignition switch ON. (Do not start engine.) Select ECU INPUT SIGNALS in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. Selector lever to P, R, N and D position to check the value of INH SW1, INH SW2, INH SW3, INH SW4 and INH SW3M.
Shift position P R N D INH SW1 OFF ON ON ON INH SW2 OFF OFF ON ON INH SW3 OFF OFF OFF ON INH SW4 OFF ON OFF ON INH SW3M OFF OFF OFF ON
SCIA2276E
1. 2.
Without CONSULT-II Turn ignition switch ON. (Do not start engine.) Change selector lever to P, R, N or D position to check voltage between the TCM connector terminals and ground.
Connector F104 Terminal 27 Ground Battery voltage 0V 34 - Ground 10.0V - Battery voltage 10.0V - Battery voltage 0V 0V 35 Ground 8.0V - Battery voltage 8.0V - Battery voltage 8.0V - Battery voltage 0V 36 Ground 10.0V Battery voltage 0V 10.0V Battery voltage 0V 32 Ground 8.0V - Battery voltage 8.0V - Battery voltage 8.0V - Battery voltage 0V
Shift position
SCIA2024E
N D
0V 0V
OK or NG OK >> GO TO 5. NG >> GO TO 2.
CVT-78
2.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH Turn ignition switch OFF. Disconnect TCM connector. Check continuity between TCM connector terminal and ground.
Terminal 27 - ground Condition Select lever in P position. Selector lever in R, N and D positions. Selector lever in P, R and N positions. Selector lever in D position. Continuity No Yes No Yes No Yes No Yes No Yes
SCIA5258E
Connector
CVT
32 - ground
F104
Select lever in P, R positions. 34 - ground Selector lever in N, D positions. Selector lever in P, R and N positions. Selector lever in D position. 36 - ground Select lever in P, N positions. Selector lever in R, D positions.
35 - ground
4. If OK, check harness for short-circuit to ground or power supply. OK or NG OK >> GO TO 5. NG >> GO TO 3.
3.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item Connector F104 F6 F104 F6 F104 F6 F104 F6 F104 F6 Terminal 27 4 34 5 35 14 32 18 36 15 Yes Yes Yes
SCIA3182E
Continuity Yes
TCM CVT unit harness connector TCM CVT unit harness connector TCM CVT unit harness connector TCM CVT unit harness connector TCM CVT unit harness connector
Yes
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 4. NG >> Repair or replace damaged parts.
CVT-79
4.
Check the following. q PNP switch. Refer to CVT-80, "Component Inspection" . OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-74, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> 1. Repair or replace damaged parts. 2. Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
Component Inspection
PNP SWITCH
1. Change selector lever to various positions to check the continuity between terminals on the PNP switch and ground.
PNP SW SW 1 Shift position R, N and D P N, D SW 2 P, R D SW 3 P, R and N R, D SW 4 SW 3 monitor P, N D P, R and N 18 - Ground 15 - Ground F6 14 - Ground 5 - Ground 4 - Ground Connector Terminal Continuity Yes No Yes No Yes No Yes No Yes No
ECS00F74
SCIA4678E
2. 3. 4.
If NG, check continuity with control cable disconnected. (Refer to step 1 above.) If OK, with the control cable disconnected, adjust the control linkage. Refer to CVT-204, "Adjustment of CVT Position" . If NG, even when the control cable is disconnected, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-80
DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT Description
The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM.
PFP:31020
A
ECS00F75
B
ECS00F76
CVT
ECS00F77
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0710 ATF TEMP SEN/CIRC with CONSULT-II is detected when TCM receives an excessively low or high voltage from the sensor.
ECS00F78
Possible Cause
q
Harness or connectors (Sensor circuit is open or shorted.) CVT fluid temperature sensor
ECS00F79
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for ENGINE with CONSULT-II. Start engine and maintain the following conditions for at least 10 minutes (Total). VHCL SPEED SE: 10 km/h (6 MPH) or more ENG SPEED: 450 rpm more than ACC PEDAL OPEN: More than 1/8 Selector lever: D position If DTC is detected, go to CVT-83, "Diagnostic Procedure" .
SCIA4823E
4.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-81
DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT Wiring Diagram CVT FTS
ECS00F7A
TCWA0247E
CVT-82
Diagnostic Procedure
CVT
1.
With CONSULT-II 1. Start engine. 2. Select ECU INPUT SIGNALS in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. Read out the value of ATF TEMP SEN.
Item name ATF TEMP SEN Condition Cold [20C (68F)] Hot [80C (176F)] Display value (Approx.) 1.8 - 2.0V 0.6 - 1.0V
G
SCIA2277E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminals.
Name CVT fluid temperature sensor Connector F104 Terminal 47 - 42 Temperature C (F) 20 (68) 80 (176) Voltage (Approx.) 2.0V 1.0V
3. 4. 5.
Turn ignition switch OFF. Disconnect TCM connector. Check if there is continuity between connector terminal and ground. OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA2027E
2.
1. 2. 3.
CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT Turn ignition switch OFF. Disconnect the TCM connector. Check resistance between TCM connector terminals.
Name Connector F104 Terminal 47 - 42 Temperature C (F) 20 (68) 80 (176) Resistance (Approx.) 6.5 k 0.9 k
OK or NG OK >> GO TO 5. NG >> GO TO 3.
SCIA2510E
CVT-83
3.
1. 2. 3.
CHECK CVT FLUID TEMPERATURE SENSOR Turn ignition switch OFF. Disconnect CVT unit harness connector. Check resistance between CVT unit harness connector terminals.
Name Connector Terminal Temperature C (F) 20 (68) F6 17 - 19 80 (176) 0.9 k Resistance (Approx.) 6.5 k
4. Reinstall any part removed. OK or NG OK >> GO TO 4. NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4679E
4.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND CVT FLUID TEMPERATURE SENSOR Turn ignition switch OFF. Disconnect the TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item Connector F104 F6 F104 F6 Terminal 42 19 47 17 Yes Continuity Yes
TCM CVT unit harness connector TCM CVT unit harness connector
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
SCIA4680E
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-81, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-84
CVT
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4679E
CVT-85
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR) DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR) Description
PFP:31935
ECS00F7D
The input speed sensor (primary speed sensor) detects the primary pulley revolution speed and sends a signal to the TCM.
ECS00F7E
Closely matches the tachometer reading. Approximately matches the engine speed.
ECS00F7F
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0715 INPUT SPD SEN/CIRC with CONSULT-II is detected when TCM does not receive the proper signal from the sensor.
ECS00F7G
Possible Cause
q
Harness or connectors (Sensor circuit is open or shorted.) Input speed sensor (Primary speed sensor)
ECS00F7H
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. Start engine and maintain the following conditions for at least 5 consecutive seconds. VHCL SPEED SE: 10 km/h (6 MPH) or more ACC PEDAL OPEN: More than 1/8 Selector lever: D position ENG SPEED: 450 rpm or more Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If DTC is detected, go to CVT-88, "Diagnostic Procedure" .
SCIA4823E
3.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-86
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR) Wiring Diagram CVT PRSCVT
ECS00F7I
CVT
TCWA0254E
CVT-87
Diagnostic Procedure
ECS00F7J
OK or NG OK >> GO TO 6. NG >> GO TO 2.
SCIA2278E
3.
Item TCM
Connector F104
Terminal 38
OK or NG OK >> GO TO 6. NG - 1 >> Battery voltage is not supplied: GO TO 3. NG - 2 >> Battery voltage is supplied, but there is a malfunction in the frequency: GO TO 4.
SCIA1915E
CVT-88
3.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND SENSOR GROUND) Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector TCM CVT unit harness connector Connector F104 F6 F104 F6 Terminal 42 19 46 20 Yes Continuity Yes
CVT
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 6. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
E
SCIA4681E
4.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR [INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)] Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector Connector F104 F6 Terminal 38 22 Yes Continuity
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
K
SCIA4682E
5.
Replace same type TCM, perform self-diagnosis check. Erase self-diagnostic results and then drive the vehicle [10 km/h (6 MPH) or more], perform self-diagnosis check. Refer to CVT-86, "DTC Confirmation Procedure" . Is the P0715 INPUT SPD SEN/CIRC detected again? YES >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NO >> Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" .
6. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-86, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 7.
CVT-89
7. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-90
DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR) DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)
PFP:31935
Description
ECS00F7K
The vehicle speed sensor CVT [output speed sensor (secondary speed sensor)] detects the revolution of the CVT output shaft and emits a pulse signal. The pulse signal is sent to the TCM, which converts it into vehicle speed.
ECS00F7L
CVT
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0720 VEH SPD SEN/CIR AT with CONSULT-II is detected TCM does not receive the proper signal from the sensor.
ECS00F7N
Possible Cause
q
Harness or connectors (Sensor circuit is open or shorted.) Output speed sensor (Secondary speed sensor)
ECS00F7O
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. Start engine and maintain the following conditions for at least 12 consecutive seconds. ACC PEDAL OPEN: More than 1/8 Selector lever: D position Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If DTC is detected, go to CVT-93, "Diagnostic Procedure" .
SCIA4823E
3.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-91
DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR) Wiring Diagram CVT SESCVT
ECS00F7P
TCWB0139E
CVT-92
W/R
CVT
*2:
Diagnostic Procedure
OK or NG OK >> GO TO 8. NG >> GO TO 2.
H
SCIA2279E
2.
1. 2.
CHECK SECONDARY SPEED SENSOR With CONSULT-II Start engine. Check power supply to output speed sensor (secondary speed sensor) by voltage between TCM connector terminals 10, 19 and 42. Refer to CVT-36, "Circuit Diagram" .
Item TCM Connector F103, F104 Terminal 10 - 42 19 - 42 Battery voltage Data (Approx.)
3.
Item TCM
Connector F104
Terminal 29
OK or NG OK >> GO TO 8. NG >> GO TO 3.
SCIA2344E
CVT-93
3.
1. 2. 3. 4.
CHECK POWER AND SENSOR GROUND Turn ignition switch OFF. Disconnect the output speed sensor (secondary speed sensor) harness connector. Turn ignition switch ON. Check voltage between output speed sensor (secondary speed sensor) harness connector terminals.
Item Connector F35 Terminal 1-3 Data (Approx.) Battery voltage
SCIA2345E
5.
Check voltage between output speed sensor (secondary speed sensor) harness connector terminal and ground.
Item Connector F35 Terminal 3 - ground Data (Approx.) Battery voltage
6. If OK, check harness for short to ground and short to power. 7. Reinstall any part removed. OK or NG OK >> GO TO 4. NG - 1 >> Battery voltage is not supplied between terminals 1 and 3, terminals 1 and ground.: GO TO 6. NG - 2 >> Battery voltage is not supplied between terminals 1 and 3 only.: GO TO 7.
SCIA2346E
4.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) Turn ignition switch OFF. Disconnect TCM connector and output speed sensor (secondary speed sensor) harness connector. Check continuity between TCM connector terminal and output speed sensor (secondary speed sensor) harness connector terminal.
Item TCM Output speed sensor (Secondary speed sensor) Connector F104 F35 Terminal 29 Yes 2 Continuity
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA1967E
CVT-94
5.
A Replace same type TCM, perform self-diagnosis check. Erase self-diagnostic results and them drive the vehicle [more than 40 km/h (25 MPH)], perform self-diagnosis check. Refer to CVT-91, "DTC Confirmation Procedure" . B Is P0720 VEH SPD SEN/CIR AT detected again? YES >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NO >> Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" . CVT
6.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) (POWER) Turn ignition switch OFF. Disconnect TCM connector and output speed sensor (secondary speed sensor) harness connector. Check continuity between TCM connector terminal and output speed sensor (secondary speed sensor) harness connector terminal. Refer to CVT-36, "Circuit Diagram" .
Item TCM Output speed sensor (Secondary speed sensor) TCM Output speed sensor (Secondary speed sensor) Connector F103 F35 F103 F35 Terminal 10 3 19 Yes 3
SCIA2369E
Continuity Yes
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> 10A fuse (No. 83, located in the IPDM E/R) or ignition switch are malfunctioning. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
7.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) (SENSOR GROUND) Turn ignition switch OFF. Disconnect TCM connector and output speed sensor (secondary speed sensor) harness connector. Check continuity between TCM connector terminal and output speed sensor (secondary speed sensor) harness connector terminal. Refer to CVT-36, "Circuit Diagram" .
Item TCM Output speed sensor (Secondary speed sensor) Connector F104 F35 Terminal 42 Yes 1 Continuity
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 8. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA2347E
8. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-91, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 9.
CVT-95
9. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-96
DTC P0725 ENGINE SPEED SIGNAL DTC P0725 ENGINE SPEED SIGNAL Description
The engine speed signal is sent from the ECM to the TCM.
PFP:24825
A
ECS00F7R
B
ECS00F7S
CVT
D
ECS00F7T
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0725 ENGINE SPEED SIG with CONSULT-II is detected when TCM does not receive the engine speed signal (input by CAN communication) from ECM.
ECS00F7U
Possible Cause
Harness or connectors (The ECM to the TCM circuit is open or shorted.)
G
ECS00F7V
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 10 consecutive seconds. PRI SPEED SEN: More than 1,000 rpm If DTC is detected, go to CVT-97, "Diagnostic Procedure" .
3.
M
SCIA4825E
Diagnostic Procedure
ECS00F7W
1.
1. 2.
With CONSULT-II Turn ignition switch ON. (Do not start engine.) Select SELF-DIAG RESULTS mode for ENGINE with CONSULT-II. Refer to EC-101, "SELF-DIAG RESULTS MODE" . OK or NG OK >> GO TO 2. NG >> Check the DTC detected item. Refer to EC-101, "SELFDIAG RESULTS MODE" .
SCIA4823E
CVT-97
2.
1. 2.
With CONSULT-II Turn ignition switch ON. (Do not start engine.) Select SELF-DIAG RESULTS mode for TRANSMISSION with CONSULT-II. Refer to CVT-58, "SELF-DIAGNOSTIC RESULT MODE" . OK or NG OK >> GO TO 3. NG >> Check the DTC detected item. Refer to CVT-58, "SELFDIAGNOSTIC RESULT MODE" . q If DTC of CAN communication line is detected, go to CVT-65, "DTC U1000 CAN COMMUNICATION LINE" .
SCIA4825E
3.
With CONSULT-II 1. Start engine. 2. Select ECU INPUT SIGNALS in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. While monitoring ENG SPEED SIG, check for engine speed change corresponding to ACC PEDAL OPEN.
Item name ENG SPEED SIG Condition Engine running Released accelerator pedal - Fully depressed accelerator pedal Display value Closely matches the tachometer reading. 0.0/8 - 8.0/8
SCIA4504E
OK or NG OK >> GO TO 4. NG >> Check ignition signal circuit. q Refer to EC-606, "IGNITION SIGNAL" .
4.
CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-97, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 5.
5.
CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-98
A
ECS00F7X
TCM selects the gear ratio using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal. Then it changes the operating pressure of the primary pulley and the secondary pulley and changes the groove width of the pulley.
ECS00F7Y
CVT
ECS00F7Z
This is not an OBD-II self-diagnostic item. TCM calculates the actual gear ratio with input speed sensor (primary speed sensor) and output speed sensor (secondary speed sensor). Diagnostic trouble code P0730 BELT DAMG with CONSULT-II is detected, when TCM receives an unexpected gear ratio signal.
ECS00F80
Possible Cause
Transaxle assembly
G
ECS00F81
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of CVT fluid temperature sensor is within the range below. FLUID TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid)
M
SCIA4825E
3. 4.
5.
Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 30 consecutive seconds. TEST START FROM 0 km/h (0 MPH) CONSTANT ACCELERATION: Keep 30 sec or more VEHICLE SPEED: 10 km/h (6 MPH) or more ACC PEDAL OPEN: More than 1/8 Selector lever: D position ENG SPEED: 450 rpm or more If DTC is detected, go to CVT-100, "Diagnostic Procedure" .
SCIA5492E
CVT-99
1. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-99, "DTC Confirmation Procedure" . Are any DTC displayed? YES - 1>> DTC except for P0730 BELT DAMG is displayed: Go to Check the DTC detected item. Refer to CVT-58, "SELF-DIAGNOSTIC RESULT MODE" . YES - 2>> DTC for P0730 BELT DAMG is displayed: Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NO >> INSPECTION END
CVT-100
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE Description
q
PFP:31940
A
ECS00F83
q q
The torque converter clutch solenoid valve is activated by the TCM in response to signals sent from the vehicle speed and throttle position sensors. Lock-up piston operation will then be controlled. B Lock-up operation, however, is prohibited when CVT fluid temperature is too low. When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up. CVT
ECS00F84
E
ECS00F85
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0740 TCC SOLENOID/CIRC with CONSULT-II is detected under the following conditions. TCM detects an improper voltage drop when it tries to operate the solenoid valve.
ECS00F86
Possible Cause
q q
Torque converter clutch solenoid valve Harness or connectors (Solenoid circuit is open or shorted.)
ECS00F87
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II and wait at least 10 consecutive seconds. If DTC is detected, go to CVT-103, "Diagnostic Procedure" .
L
SCIA4825E
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-101
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE Wiring Diagram CVT TCV
ECS00F88
TCWB0140E
CVT-102
Condition When vehicle cruises in D position. When CVT performs lock-up. When CVT does not perform lock-up.
CVT
Diagnostic Procedure
SCIA2349E
1. 2.
Without CONSULT-II Start engine. Check voltage between TCM connector terminal and ground.
Name Connector Terminal Condition When vehicle cruises in D position. Lock-up OFF Lock-up ON Voltage (Approx.) 6.0V 1.0V
F103
3 - ground
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA1917E
2.
1. 2. 3.
CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE CIRCUIT Turn ignition switch OFF. Disconnect TCM connector. Check resistance between TCM connector terminal and ground.
Solenoid valve Connector F103 Terminal 3 - Ground Resistance (Approx.) 3-9
4. 5.
Disconnect TCM connector. Check if there is continuity between the connector terminal and ground. OK or NG OK >> GO TO 5. NG >> GO TO 3.
SCIA1970E
CVT-103
3.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND TORQUE CONVERTER CLUTCH SOLENOID VALVE Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item Connector F103 F6 Terminal 3 12 Yes Continuity
4. If OK, check harness for short to ground and short to power. 5. If OK, check continuity between ground and CVT assembly. 6. Reinstall any part removed. OK or NG OK >> GO TO 4. NG >> Repair or replace damaged parts.
SCIA4683E
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-101, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-104
CVT
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4684E
CVT-105
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) Description
PFP:31940
ECS00F8B
This malfunction is detected when the torque converter clutch does not lock-up as instructed by the TCM. This is not only caused by electrical malfunction (circuits open or shorted), but also by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
ECS00F8C
Closely matches the tachometer reading. Approximately matches the engine speed.
ECS00F8D
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0744 A/T TCC S/V FNCTN with CONSULT-II is detected under the following conditions. When CVT cannot perform lock-up even if electrical circuit is good. When TCM compares difference value with slip revolution and detects an irregularity.
ECS00F8E
Possible Cause
q q
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following condition for at least 30 seconds. ACC PEDAL OPEN: More than 1.0/8 Selector lever: D position [Vehicle speed: Constant speed of more than 40 km/h (25 MPH)] If DTC is detected go to CVT-107, "Diagnostic Procedure" .
SCIA4825E
4.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-106
CVT
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SAT494G
4. CHECK SECONDARY SPEED SENSOR SYSTEM AND PRIMARY SPEED SENSOR SYSTEM
Check output speed sensor (secondary speed sensor) system and input speed sensor (primary speed sensor) system. Refer to CVT-91, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)" , CVT-86, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)" . OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
CVT-107
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-106, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> 1. Repair or replace damaged parts. 2. Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-108
DTC P0745 LINE PRESSURE SOLENOID VALVE DTC P0745 LINE PRESSURE SOLENOID VALVE Description
PFP:31940
A
ECS00F8H
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00F8I
CVT
D
ECS00F8J
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0745 L/PRESS SOL/CIRC with CONSULT-II is detected under the following conditions. TCM detects an improper voltage drop when it tries to operate the solenoid valve. When TCM compares target value with monitor value and detects an irregularity.
ECS00F8K
Possible Cause
q
Harness or connectors (Solenoid circuit is open or shorted.) Pressure control solenoid valve A (Line pressure solenoid valve)
ECS00F8L
NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. Start engine and wait at least 5 seconds. If DTC is detected, go to CVT-111, "Diagnostic Procedure" .
M
SCIA4823E
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-109
DTC P0745 LINE PRESSURE SOLENOID VALVE Wiring Diagram CVT LPSV
ECS00F8M
TCWA0249E
CVT-110
B
and Press the accelerator pedal all the way down. 1.0 - 3.0V
R/Y
CVT
Diagnostic Procedure
ECS00F8N
1.
With CONSULT-II 1. Start engine. 2. Select MAIN SIGNALS in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. Read out the value of ISOLT2.
Item name Condition Release your foot from the accelerator pedal. ISOLT2 Press the accelerator pedal all the way down. Display value (Approx.) 0.8A 0.0A
SCIA2349E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminal and ground.
Name Pressure control solenoid valve A (Line pressure solenoid valve) Connector Terminal Condition Release your foot from the accelerator pedal. F103 1 - ground Press the accelerator pedal all the way down. 1.0 - 3.0V Voltage (Approx.) 5.0 - 7.0V
3. Turn ignition switch OFF. 4. Disconnect TCM connector. 5. Check if there is continuity between connector terminal and ground. OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA2348E
CVT-111
2. CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) CIRCUIT
1. 2. 3. Turn ignition switch OFF. Disconnect TCM connector. Check resistance between TCM connector terminal and ground.
Solenoid valve Pressure control solenoid valve A (Line pressure solenoid valve) Connector Terminal Resistance (Approx.) 3-9
F103
1 - ground
OK or NG OK >> GO TO 5. NG >> GO TO 3.
SCIA4685E
F6
2 - Ground
OK or NG OK >> GO TO 4. NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4686E
4.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) Turn ignition switch OFF. Disconnect CVT unit harness connector and TCM connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector Connector F103 F6 Terminal 1 2 Yes Continuity
4. If OK, check harness for short to ground and short to power. 5. If OK, check continuity between ground and CVT assembly. 6. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA4687E
CVT-112
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-109, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> 1. Repair or replace damaged parts. 2. Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT
E
ECS00F8O
Component Inspection
PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
1. 2. 3. Turn ignition switch OFF. Disconnect CVT unit harness connector. Check resistance between CVT unit harness connector terminal and ground.
Solenoid valve Pressure control solenoid valve A (Line pressure solenoid valve) Connector Terminal Resistance (Approx.) 3-9
F6
2 - Ground
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4686E
CVT-113
DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE) DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE) PFP:31941 Description
ECS00F8P
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00F8Q
ECS00F8R
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0746 PRS CNT SOL/A FCTN with CONSULT-II is detected under the following conditions. Unexpected gear ratio was detected in the LOW side due to excessively low line pressure.
ECS00F8S
Possible Cause
q q q
Line pressure control system Output speed sensor (Secondary speed sensor) Input speed sensor (Primary speed sensor)
ECS00F8T
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 10 consecutive seconds. Test start from 0 km/h (0 MPH). ATF TEMP SEN: 1.0 - 2.0V ACC PEDAL OPEN: More than 1.0/8 Selector lever: D position VHCL SPEED: 10 km/h (6 MPH) More than Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If DTC is detected, go to CVT-115, "Diagnostic Procedure" .
SCIA4825E
3.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-114
DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE) Diagnostic Procedure
ECS00F8U
CVT
E
SCIA2366E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminal and ground.
Name Transmission fluid pressure sensor B (Primary pressure sensor) Connector Terminal Condition Voltage (Approx.)
F104
41 Ground
H
N position idle 0.7 - 3.5V
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA1922E
SAT494G
CVT-115
DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE SOLENOID VALVE)
4. CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) SYSTEM AND INPUT SPEED
SENSOR (PRIMARY SPEED SENSOR) SYSTEM Check output speed sensor (secondary speed sensor) system and input speed sensor (primary speed sensor) system. Refer to CVT-91, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)" , CVT-86, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)" . OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
6. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-114, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Replace the transaxle assembly or TCM. Refer to CVT-226, "Removal and Installation" .
CVT-116
DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE) DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE) PFP:31941 Description
A
ECS00F8V
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00F8W
CVT
D
ECS00F8X
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0776 PRS CNT SOL/B FCTN with CONSULT-II is detected when secondary pressure is too high or too low compared with the commanded value while driving.
ECS00F8Y
Possible Cause
q
q q q
Harness or connectors (Solenoid circuit is open or shorted.) Pressure control solenoid valve B (Secondary pressure solenoid valve system) Transmission fluid pressure sensor A (Secondary pressure sensor) Line pressure control system
ECS00F8Z
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 30 consecutive seconds. ATF TEMP SEN: 1.0 - 2.0V ACC PEDAL OPEN: More than 1.0/8 Selector lever: D position VHCL SPEED: 10 km/h (6 MPH) More than Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If DTC is detected, go to CVT-118, "Diagnostic Procedure" .
SCIA4825E
3.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-117
DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE) Diagnostic Procedure
ECS00F90
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA2366E
SAT494G
CVT-118
DTC P0776 PRESSURE CONTROL SOLENOID B PERFOMANCE (SEC PRESSURE SOLENOID VALVE)
A Check the following: q Power supply and ground circuit for TCM. Refer to CVT-149, "Wiring Diagram CVT POWER (LHD B Models)" , CVT-151, "Wiring Diagram CVT POWER (RHD Models)" . q The TCM pin terminals for damage or loose connection with harness connector. OK or NG CVT OK >> GO TO 6. NG >> Repair or replace damaged parts. D
6. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-117, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-119
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE) DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE) PFP:31941 Description
ECS00F91
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00F92
ECS00F93
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0778 PRS CNT SOL/B CIRC with CONSULT-II is detected under the following conditions. TCM detects an improper voltage drop when it tries to operate the solenoid valve. When TCM compares target value with monitor value and detects an irregularity.
ECS00F94
Possible Cause
q
Harness or connectors (Solenoid circuit is open or shorted.) Pressure control solenoid valve B (Secondary pressure solenoid valve)
ECS00F95
NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. Turn ignition switch ON. Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and wait at least 5 seconds. If DTC is detected, go to CVT-122, "Diagnostic Procedure" .
SCIA4825E
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-120
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE) Wiring Diagram CVT SECPSV
ECS00F96
CVT
TCWA0250E
CVT-121
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE)
TCM terminal data are reference values, measured between each terminal and ground.
Terminal Wire color Item Condition Release your foot from the accelerator pedal. Pressure control solenoid valve B (Secondary pressure solenoid valve) Data (Approx.) 5.0 - 7.0V
W/B
and Press the accelerator pedal all the way down. 3.0 - 4.0V
Diagnostic Procedure
ECS00F97
1.
With CONSULT-II 1. Start engine. 2. Select MAIN SIGNALS in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. Read out the value of ISOLT3.
Item name ISOLT3 Condition Secondary pressure low Secondary pressure high Display value (Approx.) 0.8 - 0.0A
SCIA2349E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminal and ground.
Name Pressure control solenoid valve B (Secondary pressure solenoid valve) Connector Terminal Condition Release your foot from the accelerator pedal. Voltage (Approx.) 5.0 - 7.0V
F103
2 - ground
3.0 - 4.0V
SCIA4506E
3. Turn ignition switch OFF. 4. Disconnect TCM connector. 5. Check if there is continuity between connector terminal and ground. OK or NG OK >> GO TO 5. NG >> GO TO 2.
CVT-122
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE)
2. CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) CIRCUIT
1. 2. 3. Turn ignition switch OFF. Disconnect TCM connector. Check resistance between TCM connector terminal and ground.
Solenoid valve Pressure control solenoid valve B (Secondary pressure solenoid valve) Connector Terminal Resistance (Approx.) 3-9
CVT
F103
2 - Ground
OK or NG OK >> GO TO 5. NG >> GO TO 3.
SCIA4507E
F6
3 - Ground
SCIA4688E
M
Yes
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
SCIA4689E
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-120, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
CVT-123
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE SOLENOID VALVE)
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> 1. Repair or replace damaged parts. 2. Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
Component Inspection
1. 2. 3. Turn ignition switch OFF. Disconnect CVT unit harness connector. Check resistance between CVT unit harness connector terminal and ground.
Solenoid Valve Pressure control solenoid valve B (Secondary pressure solenoid valve) Connector Terminal Resistance (Approx.) 3-9
ECS00F98
F6
3 - Ground
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4688E
CVT-124
DTC P0826 MANUAL MODE SWITCH CIRCUIT DTC P0826 MANUAL MODE SWITCH CIRCUIT Description
PFP:34901
A
ECS00F99
Manual mode switch is installed in CVT control device. The manual mode switch sends shift up and shift down switch signals to TCM. TCM sends the switch signals to unified meter and A/C amp via CAN communication line. Then manual mode switch position is indicated on the CVT position indicator. For inspection, refer to CVT-175, "Diagnostic Procedure" .
CVT
ECS00F9A
G
ECS00F9B
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0826 MANUAL MODE SWITCH with CONSULT-II is detected when TCM monitors Manual mode, Non manual mode, Up or Down switch signal, and then detects irregular with impossible input pattern for 1 second or more.
ECS00F9C
Possible Cause
q
q q
Harness or connectors (These switches circuit is open or shorted.) (TCM, and unified meter and A/C amp circuit are open or shorted.) (CAN communication line is open or shorted.) Manual mode select switch (Built into CVT control device) Manual mode position select switch (Built into CVT control device)
ECS00F9D
NOTE: If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. 5. 6. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine. Move selector lever to M position. Drive vehicle for at least 2 consecutive seconds. If DTC is detected, go to CVT-129, "Diagnostic Procedure" .
SCIA4825E
CVT-125
DTC P0826 MANUAL MODE SWITCH CIRCUIT Wiring Diagram CVT MMSW (LHD Models)
ECS00F9E
TCWB0141E
CVT-126
A
Item Condition Data (Approx.)
CVT
CVT-127
DTC P0826 MANUAL MODE SWITCH CIRCUIT Wiring Diagram CVT MMSW (RHD Models)
ECS00FZ1
TCWB0142E
CVT-128
A
Item Condition Data (Approx.)
ECS00F9F
Diagnostic Procedure
CVT
Without CONSULT-II Drive vehicle in the manual mode, and confirm that the actual gear position and the meter's indication of the position mutually coincide when the selector lever is shifted to the + (up) or - (down) side (1st 6th gear). OK or NG OK >> GO TO 7. NG >> GO TO 3.
CVT-129
Continuity Yes
4.
Check continuity between CVT device harness connector terminal and ground.
Item Connector M57 Terminal 11 Continuity Yes
5. If OK, check harness for short to ground and short to power. 6. Reinstall any part removed. OK or NG OK >> GO TO 7. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA4590E
7. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-125, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 8.
CVT-130
8. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
Component Inspection
MANUAL MODE SWITCH
Check continuity between CVT device harness connector terminals.
Item Manual mode select switch Manual mode position select switch Position Auto Manual Up Down M57 Connector Terminal 12 - 11 3 - 11 8 - 11 7 - 11 Yes Continuity
CVT
ECS00F9G
SCIA4591E
CVT-131
DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR) DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR) PFP:31936 Description
The transmission fluid pressure sensor A (secondary pressure sensor) detects secondary pressure of CVT and sends TCM the signal.
ECS00F9H
ECS00F9I
ECS00F9J
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0840 TR PRS SENS/A CIRC with CONSULT-II is detected when TCM detects an improper voltage drop when it receives the sensor signal.
ECS00F9K
Possible Cause
q q
Transmission fluid pressure sensor A (Secondary pressure sensor) Harness or connectors (Switch circuit is open or shorted.)
ECS00F9L
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of line temperature sensor is within the range below. ATF TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid) Start engine and wait for at least 5 consecutive seconds. If DTC is detected, go to CVT-134, "Diagnostic Procedure" .
SCIA4825E
3. 4.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-132
DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR) Wiring Diagram CVT SECPS
ECS00F9M
CVT
TCWA0253E
CVT-133
DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)
TCM terminal data are reference values, measured between each terminal and ground.
Terminal Wire color Item Condition Data (Approx.)
37
V/W
and
N position idle
0.8V
42
W/R
Sensor ground
Always
0V 4.5 - 5.5V
46
L/O
Sensor power 0V
Diagnostic Procedure
ECS00F9N
SCIA2279E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminal and ground.
Name Transmission fluid pressure sensor A (Secondary pressure sensor) Connector Terminal Condition Voltage (Approx.)
F104
37 - Ground
N position idle
0.8V
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA4508E
CVT-134
DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)
B
Item TCM connector Connector F104 Terminal 46 - 42 Data (Approx.) 4.5 - 5.5V
CVT
OK or NG OK >> GO TO 4. NG >> GO TO 3.
SCIA2367E
3.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND SENSOR GROUND) Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector TCM CVT unit harness connector Connector F104 F6 F104 F6 Terminal 42 19 46 20 Yes Continuity Yes
I
SCIA4681E
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" . NG >> Repair open circuit or short to ground or short to power in harness or connectors.
4. CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) CIRCUIT 1. 2. 3. Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector Connector F104 F6 Terminal 37 23 Yes Continuity
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA4690E
CVT-135
DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-132, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-136
DTC P0841 PRESSURE SENSOR FUNCTION DTC P0841 PRESSURE SENSOR FUNCTION Description
PFP:31936
A
ECS00F9O
Using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal, TCM changes the operating pressure of the primary pulley and the secondary pulley and changes the groove width of the pulley to control the gear ratio.
ECS00F9P
CVT
D
ECS00F9Q
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0841 PRESS SEN/FNCTN with CONSULT-II is detected when correlation between the values of the secondary pressure sensor and the primary pressure sensor is out of specification.
ECS00F9R
Possible Cause
q q q
Transmission fluid pressure sensor A (Secondary pressure sensor) Transmission fluid pressure sensor B (Primary pressure sensor) Harness or connectors (Sensor circuit is open or shorted.)
ECS00F9S
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 12 consecutive seconds. VHCL SPEED: 40 km/h (25 MPH) More than Selector lever: D position If DTC is detected, go to CVT-138, "Diagnostic Procedure" .
L
3.
SCIA4825E
CVT-137
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminals and ground.
Name Transmission fluid pressure sensor B (Primary pressure sensor) Transmission fluid pressure sensor A (Secondary pressure sensor) F104 37 - Ground Connector Terminal Condition Voltage (Approx.)
0.7 - 3.5V
0.8V
SCIA6879E
OK or NG OK >> GO TO 6. NG >> GO TO 3.
SAT494G
CVT-138
4. CHECK TRANSMISSION FLUID PRESSORE SENSOR A (SECONDARY PRESSURE SENSOR) SYSTEM AND TRANSMISSION FLUID PRESSURE SENSOR B (PRIMARY PRESSURE SENSOR) SYSTEM
Check secondary pressure sensor system and primary pressure sensor system. Refer to CVT-132, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)" , CVT-140, B "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)" . OK or NG OK >> GO TO 5. CVT NG >> Repair or replace damaged parts.
6. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-137, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Replace TCM or transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-139
DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR) DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR) PFP:31936 Description
The primary pressure sensor detects primary pressure of CVT and sends TCM the signal.
ECS00F9U
ECS00F9V
ECS00F9W
This is an OBD-II self-diagnostic item. Diagnostic trouble code P0845 TR PRS SENS/B CIRC with CONSULT-II is detected under the following conditions. When TCM detects an improper voltage drop when it receives the sensor signal. When TCM compares target value with monitor value and detects an irregularity.
ECS00F9X
Possible Cause
q q
Transmission fluid pressure sensor B (Primary pressure sensor) Harness or connectors (Sensor circuit is open or shorted.)
ECS00F9Y
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of line temperature sensor is within the range below. ATF TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid) Start engine and wait for at least 5 consecutive seconds. If DTC is detected, go to CVT-142, "Diagnostic Procedure" .
SCIA4825E
3. 4.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-140
DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR) Wiring Diagram CVT PRIPS
ECS00F9Z
CVT
TCWA0255E
CVT-141
DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)
TCM terminal data are reference values, measured between each terminal and ground.
Terminal Wire color Item Condition Data (Approx.)
41
V/O
and
N position idle
0.7 - 3.5V
42
W/R
Sensor ground
Always
0V 4.5 - 5.5V
46
L/O
Sensor power 0V
Diagnostic Procedure
ECS00FA0
SCIA2277E
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM connector terminal and ground.
Name Transmission fluid pressure sensor B (Primary pressure sensor) Connector Terminal Condition Voltage (Approx.)
F104
41 - Ground
N position idle
0.7 - 3.5V
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA4509E
CVT-142
DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)
B
Item TCM connector Connector F104 Terminal 46 - 42 Data (Approx.) 4.5 - 5.5V
CVT
OK or NG OK >> GO TO 4. NG >> GO TO 3.
SCIA2367E
3.
1. 2. 3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND SENSOR GROUND) Turn ignition switch OFF. Disconnect TCM connector and CVT unit harness connector. Check continuity between TCM connector terminal and CVT unit harness connector terminal.
Item TCM CVT unit harness connector TCM CVT unit harness connector Connector F104 F6 F104 F6 Terminal 42 19 46 20 Yes Continuity Yes
I
SCIA4681E
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" . NG >> Repair open circuit or short to ground or short to power in harness or connectors.
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA4691E
CVT-143
DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT (PRI PRESSURE SENSOR)
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-140, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-144
DTC P0868 SECONDARY PRESSURE DOWN DTC P0868 SECONDARY PRESSURE DOWN Description
PFP:31941
A
ECS00FA1
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00FA2
CVT
ECS00FA3
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P0868 SEC/PRESS DOWN with CONSULT-II is detected when secondary fluid pressure is too low compared with the commanded value while driving.
ECS00FA4
Possible Cause
q
q q q
Harness or connectors (Solenoid circuit is open or shorted.) Pressure control solenoid valve B (Secondary pressure solenoid valve) system Transmission fluid pressure sensor A (Secondary pressure sensor) Line pressure control system
ECS00FA5
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of CVT fluid temperature sensor is within the range below. FLUID TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid) Start engine and maintain the following conditions for at least 10 consecutive seconds. VEHICLE SPEED (accelerate slowly): 0 50 km/h (31 MPH) ACC PEDAL OPEN: 0.5/8 - 1.0/8 Selector lever: D position If DTC is detected, go to CVT-146, "Diagnostic Procedure" .
K
3.
SCIA4825E
4.
CVT-145
OK or NG OK >> GO TO 5. NG >> GO TO 2.
SCIA2366E
SAT494G
4. CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYSTEM Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to CVT-132, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT (SEC PRESSURE SENSOR)" . OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
CVT-146
A Check the following: q Power supply and ground circuit for TCM. Refer to CVT-149, "Wiring Diagram CVT POWER (LHD B Models)" , CVT-151, "Wiring Diagram CVT POWER (RHD Models)" . q The TCM pin terminals for damage or loose connection with harness connector. OK or NG CVT OK >> GO TO 6. NG >> Repair or replace damaged parts. D
6. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-145, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-147
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY) DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY) Description
PFP:31036
ECS00FA7
When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diagnosis memory function stops, malfunction is detected. NOTE: Since P1701 TCM-POWER SUPPLY will be indicated when replacing TCM, perform diagnosis after erasing SELF-DIAG RESULTS
ECS00FA8
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1701 TCM-POWER SUPPLY with CONSULT-II is detected when TCM does not receive the voltage signal from the battery power supply. This is not a malfunction message. (Whenever shutting OFF a power supply to the TCM, this message appears on the screen.)
ECS00FA9
Possible Cause
Harness or connectors (Battery or ignition switch and TCM circuit is open or shorted.)
ECS00FAA
NOTE: If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. Turn ignition switch ON. (Do not start engine.) Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Wait for at least 2 consecutive seconds. If DTC is detected, go to CVT-152, "Diagnostic Procedure" .
SCIA4825E
CVT-148
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY) Wiring Diagram CVT POWER (LHD Models)
ECS00FAB
CVT
TCWB0143E
CVT-149
19 Y Power supply 25 28 48 B Y/R B Ground Power supply (memory back-up) Ground Always Always Always
Battery voltage
0V 0V Battery voltage 0V
CVT-150
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY) Wiring Diagram CVT POWER (RHD Models)
ECS00G4H
CVT
TCWB0144E
CVT-151
19 Y Power supply 25 28 48 B Y/R B Ground Power supply (memory back-up) Ground Always Always Always
Battery voltage
0V 0V Battery voltage 0V
ECS00FAC
Diagnostic Procedure
1. CHECK DTC
Turn ignition switch ON. (Do not start engine.) Select SELF-DIAG RESULTS mode for TRANSMISSION with CONSULT-II. 3. Erase self-diagnostic results. Refer to CVT-60, "How to Erase Self-diagnostic Results" . 4. Turn ignition switch OFF, and wait for 5 seconds or more. 5. Start engine. 6. Confirm self-diagnostic results again. Refer to CVT-58, "SELFDIAGNOSTIC RESULT MODE" . Is the P1701 TCM-POWER SUPPLY displayed? YES >> GO TO 2. NO >> INSPECTION END 1. 2.
SCIA5492E
OK or NG OK >> GO TO 3. NG >> GO TO 4.
SCIA4783E
CVT-152
B
Name Connector Terminal Condition Voltage (Approx.) Battery voltage Power supply 10 - Ground
CVT
D
0V
SCIA4784E
F
0V Power supply (memory back-up) Battery voltage
F104
28 - Ground
Always
OK or NG OK >> GO TO 5. NG >> GO TO 4.
OK or NG OK >> GO TO 6. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA2671E
CVT-153
6. CHECK DTC
Check again. Refer to CVT-152, "Diagnostic Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 7.
7. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-154
DTC P1705 THROTTLE POSITION SENSOR DTC P1705 THROTTLE POSITION SENSOR Description
PFP:22620
A
ECS00FAD
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM sends the signal to TCM with CAN communication.
ECS00FAE
CVT
D
ECS00FAF
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1705 TP SEN/CIRC A/T with CONSULT-II is detected when TCM does not receive the proper accelerator pedal position signals (input by CAN communication) from ECM.
ECS00FAG
Possible Cause
q q
NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Depress accelerator pedal fully and release it, then wait for 5 seconds. If DTC is detected, go to CVT-156, "Diagnostic Procedure" .
L
SCIA4825E
CVT-155
OK or NG OK >> GO TO 4. NG >> GO TO 3.
SCIA2272E
4. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-155, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-156
DTC P1722 ESTM VEHICLE SPEED SIGNAL DTC P1722 ESTM VEHICLE SPEED SIGNAL Description
PFP:47660
A
ECS00FAJ
The vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) to TCM by CAN communication line.
ECS00FAK
CVT
D
ECS00FAL
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1722 ESTM VEH SPD SIG with CONSULT-II is detected when TCM does not receive the proper vehicle speed signal (input by CAN communication) from ABS actuator and electric unit (control unit).
ECS00FAM
Possible Cause
q
Harness or connectors (Sensor circuit is open or shorted.) ABS actuator and electric unit (control unit)
ECS00FAN
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 5 consecutive seconds. ACCELE POS: 1/8 or less VHCL SPEED SE: 30 km/h (17 MPH) or more If DTC is detected, go to CVT-158, "Diagnostic Procedure" .
SCIA4825E
4.
CVT-157
4.
OK or NG OK >> GO TO 5. NG >> GO TO 4.
4. CHECK TCM
Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . OK or NG OK >> GO TO 5. NG >> Repair or replace damaged parts.
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-157, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 2.
CVT-158
DTC P1723 CVT SPEED SENSOR FUNCTION DTC P1723 CVT SPEED SENSOR FUNCTION Description
PFP:31907
A
ECS00FAP
The vehicle speed sensor CVT [output speed sensor (secondary speed sensor)] detects the revolution of the idler gear parking pawl lock gear and generates a pulse signal. The pulse signal is sent to the TCM, which converts it into vehicle speed. The input speed sensor (primary speed sensor) detects the primary pulley revolution speed and sends a signal to the TCM.
CVT
ECS00FAQ
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1723 CVT SPD SEN/FNCTN with CONSULT-II is detected when there is a great difference between the vehicle speed signal and the secondary speed sensor signal. CAUTION: One of the P0720 VEH SPD SEN/CIR AT, the P0715 INPUT SPD SEN/CIRC or the P0725 ENGINE SPEED SIG is displayed with the DTC at the same time.
ECS00FAR
Possible Cause
q
q q q
Harness or connectors (Sensor circuit is open or shorted.) Output speed sensor (Secondary speed sensor) Input speed sensor (Primary speed sensor) Engine speed signal system
ECS00FAS
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 5 consecutive seconds. VHCL SPEED SE: 10 km/h (6 MPH) or more THRTL POS SEN: More than 1.2V Selector lever: D position ENG SPEED: 450 rpm or more Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If DTC is detected, go to CVT-160, "Diagnostic Procedure" .
SCIA4825E
3.
CVT-159
2. CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR SYSTEM) AND INPUT SPEED
SENSOR (PRIMARY SPEED SENSOR) SYSTEM Check secondary speed sensor system and primary speed sensor system. Refer to CVT-91, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)" , CVT-86, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)" . OK or NG OK >> GO TO 3. NG >> Repair or replace damaged parts.
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-159, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> Replace TCM or transaxle assembly. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" , CVT-226, "Removal and Installation" .
CVT-160
DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM Description
PFP:23710
A
ECS00FAU
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM sends the signal to TCM with CAN communication.
ECS00FAV
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1726 ELEC TH CONTROL with CONSULT-II is detected when the electronically controlled throttle for ECM is malfunctioning.
ECS00FAW
CVT
Possible Cause
Harness or connectors (Sensor circuit is open or shorted.)
E
ECS00FAX
NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. 4. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and let it idle for 5 second. If DTC is detected, go to CVT-162, "Diagnostic Procedure" .
H
SCIA4825E
CVT-161
2. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-161, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 3.
CVT-162
DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT Description
q
PFP:31941
A
ECS00FAZ
Lock-up select solenoid valve controls lock-up clutch pressure or forward clutch pressure (reverse brake pressure). When controlling lock-up clutch, the valve is turned OFF. When controlling forward clutch, it is turned ON.
ECS00FB0
CVT
ECS00FB1
This is an OBD-II self-diagnostic item. Diagnostic trouble code P1740 LU-SLCT SOL/CIRC with CONSULT-II is detected under the following conditions. When TCM compares target value with monitor value and detects an irregularity.
ECS00FB2
Possible Cause
q q
Lock-up select solenoid valve Harness or connectors (Solenoid circuit is open or shorted.)
ECS00FB3
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON. (Do not start engine.) Select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Start engine and maintain the following conditions for at least 5 consecutive seconds. SELECTOR LEVER: D position and N position (At each time, wait for 5 seconds.) If DTC is detected, go to CVT-165, "Diagnostic Procedure" .
SCIA4825E
4.
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-163
DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT Wiring Diagram CVT L/USSV
ECS00FB4
TCWB0145E
CVT-164
Condition Selector lever in P, N positions Wait at least for 5 seconds with the selector lever in R, D positions
CVT
Diagnostic Procedure
1.
1. 2.
With CONSULT-II Turn ignition switch ON. Select SELECTION FROM MENU in DATA MONITOR mode for TRANSMISSION with CONSULT-II. 3. Read out the value of LUSEL SOL OUT.
Item name Condition Selector lever in P, N positions LUSEL SOL OUT Wait at least for 5 seconds with the selector lever in R, D positions Display value ON
OFF
SCIA4512E
1. 2.
Without CONSULT-II Turn ignition switch ON. Check voltage between TCM connector terminal and ground.
Name Connector Terminal Condition Selector lever in P, N positions F103 4 - Ground Wait at least for 5 seconds with the selector lever in R, D positions Voltage (Approx.) Battery voltage
K
0V
3. Turn ignition switch OFF. 4. Disconnect the TCM connector. 5. Check if there is continuity between connector terminal and ground. OK or NG OK >> GO TO 5. NG >> GO TO 2.
L
SCIA4513E
CVT-165
OK or NG OK >> GO TO 5. NG >> GO TO 3.
SCIA4692E
OK or NG OK >> GO TO 4. NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4693E
4. If OK, check harness for short to ground and short to power. 5. Reinstall any part removed. OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA4694E
5. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-163, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
CVT-166
6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> 1. Repair or replace damaged parts. 2. Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" .
CVT
ECS00FB6
Component Inspection
LOCK-UP SELECT SOLENOID VALVE
1. 2. 3. Turn ignition switch OFF. Disconnect CVT unit harness connector. Check resistance between CVT unit harness connector terminal and ground.
Solenoid valve Lock-up select solenoid valve Connector F6 Terminal 13 - Ground Resistance (Approx.) 6 - 19
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
SCIA4693E
CVT-167
DTC P1745 LINE PRESSURE CONTROL DTC P1745 LINE PRESSURE CONTROL Description
PFP:31036
ECS00FB7
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.
ECS00FB8
This is not an OBD-II self-diagnostic item. Diagnostic trouble code P1745 L/PRESS CONTROL with CONSULT-II is detected when TCM detects the unexpected line pressure.
ECS00FB9
Possible Cause
TCM
ECS00FBA
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of CVT fluid temperature sensor is within the range below. FLUID TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid) If DTC is detected, go to CVT-168, "Diagnostic Procedure" .
SCIA4825E
3.
Diagnostic Procedure
ECS00FBB
1. CHECK DTC
Turn ignition switch ON. (Do not start engine.) Select SELF-DIAG RESULTS mode for TRANSMISSION with CONSULT-II. 3. Erase self-diagnostic results. Refer to CVT-60, "How to Erase Self-diagnostic Results" . 4. Turn ignition switch OFF, and wait for 5 seconds or more. 5. Start engine. 6. Confirm self-diagnostic results again. Refer to CVT-58, "SELFDIAGNOSTIC RESULT MODE" . Is the P1745 L/PRESS CONTROL displayed? YES >> Replace TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" . NO >> INSPECTION END 1. 2.
SCIA5492E
CVT-168
DTC P1777 STEP MOTOR - CIRCUIT DTC P1777 STEP MOTOR - CIRCUIT Description
q
PFP:31020
A
ECS00FBC
The step motor changes the step with turning 4 coils ON/OFF according to the signal from TCM. As a result, the flow of line pressure to primary pulley is changed and pulley ratio is controlled.
ECS00FBD
CVT
E
ECS00FBE
This is an OBD-II self-diagnostic item. Diagnostic trouble code P1777 STEP MOTR CIRC with CONSULT-II is detected under the following conditions. When operating step motor ON and OFF, there is no proper change in the voltage of TCM terminal which corresponds to it.
ECS00FBF
Possible Cause
q q
CAUTION: Always drive vehicle at a safe speed. NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. 3. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Drive vehicle for at least 5 consecutive seconds. If DTC is detected, go to CVT-171, "Diagnostic Procedure" .
SCIA4825E
WITH GST
Follow the procedure WITH CONSULT-II.
CVT-169
TCWA0256E
CVT-170
CVT
ECS00FBI
Diagnostic Procedure
OK or NG OK >> GO TO 4. NG >> GO TO 2.
SCIA4695E
4. If OK, check harness for short to ground and short to power. 5. If OK, check continuity between body ground and CVT assembly. 6. Reinstall any part removed. OK or NG OK >> GO TO 3. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
CVT-171
4. CHECK DTC
Perform DTC Confirmation Procedure. Refer to CVT-169, "DTC Confirmation Procedure" . OK or NG OK >> INSPECTION END NG >> GO TO 5.
5. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
Component Inspection
STEP MOTOR
1. 2. 3. Turn ignition switch OFF. Disconnect CVT unit harness connector. Check resistance between CVT unit harness connector terminals and ground.
Control valve Connector Terminal 6-7 8-9 Step motor F6 6 - Ground 7 - Ground 8 - Ground 9 - Ground 15 Resistance (Approx.) 30
ECS00FBJ
SCIA4696E
4.
If NG, replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
CVT-172
DTC P1778 STEP MOTOR - FUNCTION DTC P1778 STEP MOTOR - FUNCTION Description
q
PFP:31947
A
ECS00FBK
q q
The step motor's 4 aspects of ON/OFF change according to the signal from TCM. As a result, the flow of line pressure to primary pulley is changed and pulley ratio is controlled. B This diagnosis item is detected when electrical system is OK, but mechanical system is NG. This diagnosis item is detected when the state of the changing the speed mechanism in unit does not operate normally. CVT
ECS00FBL
E
ECS00FBM
This is an OBD-II self-diagnostic item. Diagnostic trouble code P1778 STEP MOTR/FNC with CONSULT-II is detected under the following conditions. When not changing the pulley ratio according to the instruction of TCM.
ECS00FBN
Possible Cause
Step motor
H
ECS00FBO
CAUTION: q Always drive vehicle at a safe speed. q Be careful not to rev engine into the red zone on the tachometer. q Before starting DTC Confirmation Procedure, confirm Hi or Mid or Low fixation by PRI SPEED and VEHICLE SPEED on DATA MONITOR MODE. q If hi-geared fixation occurred, go to CVT-174, "Diagnostic Procedure" . NOTE: If DTC Confirmation Procedure has been previously performed, always turn ignition switch OFF and wait at least 5 seconds before performing the next test. After the repair, touch ERASE on SELF-DIAG RESULTS and then perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. 2. Turn ignition switch ON and select DATA MONITOR mode for TRANSMISSION with CONSULT-II. Make sure that output voltage of CVT fluid temperature sensor is within the range below. FLUID TEMP SEN: 1.0 - 2.0V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid)
M
SCIA4825E
CVT-173
5.
SCIA5492E
WITH GST
Follow the procedure WITH CONSULT-II.
Diagnostic Procedure
ECS00FBP
CVT-174
A
ECS00FBV
TCM sends the switch signals to unified meter and A/C amp via CAN communication line. Then manual mode switch position is indicated on the CVT indicator.
ECS00FBW
CVT
Diagnostic Procedure
ECS00FBX
CVT-175
TROUBLE DIAGNOSIS FOR SYMPTOMS TROUBLE DIAGNOSIS FOR SYMPTOMS Wiring Diagram CVT NONDTC (LHD Models)
PFP:00007
ECS00FBY
TCWB0146E
CVT-176
CVT
TCWB0147E
CVT-177
TCWA0258E
CVT-178
A
Item Condition Selector lever in R position. Selector lever in other positions. Always 0V 0V Battery voltage Data (Approx.)
CVT
E
4.5 - 5.5V
46
L/O
Sensor power 0V
CVT-179
TROUBLE DIAGNOSIS FOR SYMPTOMS Wiring Diagram CVT NONDTC (RHD Models)
ECS00G4I
TCWB0148E
CVT-180
CVT
TCWB0149E
CVT-181
TCWB0150E
CVT-182
A
Item Condition Selector lever in R position. Selector lever in other positions. Always 0V 0V Battery voltage Data (Approx.)
CVT
E
4.5 - 5.5V
46
L/O
Sensor power 0V
CVT-183
TROUBLE DIAGNOSIS FOR SYMPTOMS CVT Indicator Lamp Does Not Come On
SYMPTOM:
CVT indicator lamp does not come on for about 2 seconds when turning ignition switch to ON.
ECS00FBZ
DIAGNOSTIC PROCEDURE
OK or NG OK >> GO TO 4. NG >> GO TO 3.
CVT-184
CVT
OK or NG OK >> GO TO 5. NG >> Repair open circuit or short to ground or short to power in harness or connectors.
SCIA2671E
6. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check Before Engine Is Started" . OK or NG OK >> INSPECTION END NG >> GO TO 7.
CVT-185
Engine cannot be started with selector lever in P or N position. Engine can be started with selector lever in D, M or R position.
DIAGNOSTIC PROCEDURE
SCIA2001E
CVT-186
TROUBLE DIAGNOSIS FOR SYMPTOMS In P Position, Vehicle Moves Forward or Backward When Pushed
SYMPTOM:
Vehicle moves when it is pushed forward or backward with selector lever in P position.
ECS00FC1
DIAGNOSTIC PROCEDURE
Perform self-diagnosis check. Refer to CVT-58, "SELF-DIAGNOSTIC RESULT MODE" . CVT Do the self-diagnostic results indicate PNP switch circuit? YES >> Check PNP switch circuit. Refer to CVT-74, "DTC P0705 PARK/NEUTRAL POSITION SWITCH" . NO >> GO TO 2. D
SCIA2001E
3. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check at Idle" . OK or NG OK >> INSPECTION END NG >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" .
I J
CVT-187
DIAGNOSTIC PROCEDURE
SCIA2001E
SAT638A
4. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check at Idle" . OK or NG OK >> INSPECTION END NG >> GO TO 5.
5. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-188
DIAGNOSTIC PROCEDURE
CVT
J
SAT638A
SAT494G
5. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check at Idle" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
CVT-189
6. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-190
TROUBLE DIAGNOSIS FOR SYMPTOMS Vehicle Does Not Creep Backward in R Position
SYMPTOM:
Vehicle does not creep backward when selecting R position.
ECS00FC4
DIAGNOSTIC PROCEDURE
CVT
SCIA2001E
L
SAT638A
SAT494G
CVT-191
5. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check at Idle" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-192
TROUBLE DIAGNOSIS FOR SYMPTOMS Vehicle Does Not Creep Forward in D Position
SYMPTOM:
Vehicle does not creep forward when selecting D position.
ECS00FC5
DIAGNOSTIC PROCEDURE
CVT
SCIA2001E
L
SAT638A
SAT494G
CVT-193
5. CHECK SYMPTOM
Check again. Refer to CVT-44, "Check at Idle" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-194
DIAGNOSTIC PROCEDURE
CVT
SCIA2001E
L
SAT638A
SAT494G
CVT-195
5. CHECK SYMPTOM
Check again. Refer to CVT-47, "Cruise Test" . OK or NG OK >> INSPECTION END NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-196
DIAGNOSTIC PROCEDURE
CVT
3. CHECK SYMPTOM
Check again. Refer to CVT-47, "Cruise Test" . OK or NG OK >> INSPECTION END NG >> GO TO 4.
G H
4. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> INSPECTION END NG >> Repair or replace damaged parts.
CVT-197
TROUBLE DIAGNOSIS FOR SYMPTOMS CVT Does Not Shift in Manual Mode
SYMPTOM:
Speed does not change even if the selector lever is put in the manual shift gate position and the selector lever is operated to + side or to - side.
ECS00FC8
DIAGNOSTIC PROCEDURE
SCIA2001E
SAT638A
CVT-198
CVT
D
SAT494G
6. CHECK SYMPTOM
Check again. Refer to CVT-47, "Cruise Test" . OK or NG OK >> INSPECTION END NG >> GO TO 7.
7. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-199
TROUBLE DIAGNOSIS FOR SYMPTOMS Vehicle Does Not Decelerate by Engine Brake
SYMPTOM:
No engine brake is applied when the gear is shifted from the M2 to M1 position.
ECS00FCB
DIAGNOSTIC PROCEDURE
SCIA2001E
SAT638A
SAT494G
CVT-200
6. CHECK SYMPTOM
Check again. Refer to CVT-47, "Cruise Test" . OK or NG OK >> INSPECTION END NG >> GO TO 7.
CVT
7. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-50, "TCM Input/Output Signal Reference Values" . 2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector. OK or NG OK >> Replace the transaxle assembly. Refer to CVT-226, "Removal and Installation" . NG >> Repair or replace damaged parts.
CVT-201
SCIA6463E
1. 4. 7.
2. 5.
3. 6.
CVT-202
CVT
SCIA5988E
1. 4. 7.
2. 5.
3. 6.
REMOVAL
1. 2. 3. 4. 5. Remove knob cover below selector lever downward. Pull lock pin out of selector lever knob. Remove selector lever knob. Remove A/T console finisher. q Refer to IP-17, "Removal and Installation" . Remove console box assembly. q Refer to IP-17, "Removal and Installation" .
I
SCIA4377E
6. 7.
Disconnect control cable of control device. Disconnect control device harness connector.
SCIA5963E
CVT-203
SCIA5964E
INSTALLATION
Note the following, and install in the reverse order of removal. The knurled surface of rib should be upward when installing the control cable to the control device assembly. And insert the control cable securely. q After installation is completed, adjust and check CVT position. Refer to CVT-204, "Adjustment of CVT Position" and CVT-205, "Checking of CVT Position" .
q
SCIA5990E
ECS00FCD
3.
4.
SCIA2001E
5.
CVT-204
5. 6.
7. 8. 9.
A Place selector lever in P position, and turn ignition switch ON (engine stop). Make sure selector lever can be shifted to other than P position when brake pedal is depressed. Also make sure selector lever can be shifted from P position only when brake pedal is depressed. B Move the selector lever and check for excessive effort, sticking, noise or rattle. Confirm the selector lever stops at each position with the feel of engagement when it is moved through all the positions. Check whether or not the actual position the selector lever is in matches the position shown CVT by the shift position indicator and the transaxle body. The method of operating the lever to individual positions correctly should be as shown in the figure. D Confirm the back-up lamps illuminate only when lever is placed in the R position. Confirm the back-up lamps do not illuminate when the selector lever is pushed toward the R position side with the gear position remained in the P or N position. E Confirm the engine can only be started with the selector lever in the P and N positions. Make sure transaxle is locked completely in P position. F When selector lever is set to manual shift gate, make sure manSCIA4595E ual mode is displayed on combination meter. Shift selector lever to + and - sides, and make sure set shift position changes. G
CVT-205
PFP:00000
ECS00FCF
The electrical key interlock mechanism also operates as a shift lock: With the ignition switch turned to ON, the selector lever cannot be shifted from P (parking) to any other position unless the brake pedal is depressed. With the key removed, the selector lever cannot be shifted from P to any other position. The key cannot be removed unless the selector lever is placed in P. The shift lock and key interlock mechanisms are controlled by the ON-OFF operation of the shift lock solenoid and by the operation of the rotator and slider located inside the key cylinder, respectively.
ECS00FCG
SCIA6683E
NOTE: This emergency lever can be used when battery is off ignition key cannot be removed. In the situation like this, by operating this lever, ignition key can be removed.
CVT-206
CVT SHIFT LOCK SYSTEM Wiring Diagram CVT SHIFT (LHD Models)
ECS00FCH
CVT
TCWB0151E
CVT-207
TCWA0166E
CVT-208
CVT SHIFT LOCK SYSTEM Wiring Diagram CVT SHIFT (RHD Models)
ECS00FCI
CVT
TCWB0152E
CVT-209
TCWB0153E
CVT-210
CVT SHIFT LOCK SYSTEM Shift Lock Control Unit Reference Values
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
ECS00FCJ
CVT
D
SCIA2004E
F
Battery voltage Battery voltage Approx. 0V Battery voltage Approx. 0V Battery voltage Approx. 0V
3 (L/W) 4 (R/G)
J
5 (V/W) Vehicle speed signal (8pulse signal) Speed meter is operated
K
ELF1084D
6 (G)
When selector lever is in P position, brake pedal is depressed, and ignition switch is ON. When selector lever is not in P position, ignition switch is ON, and vehicle speed is 10 km/h (6 MPH) or less. For 3 minutes after selector lever is not in P position, vehicle speed is 10 km/h (6 MPH) or less, and ignition switch is ON OFF. Battery voltage Approx. 0V Battery voltage for approx. 0.1 sec. (Note) Approx. 0V Battery voltage for approx. 0.1 sec. (Note) Approx. 0V
M
Approx. 0V
7 (R/L)
When selector lever is not P position. Key lock solenoid When selector lever is in P position. When selector lever is in P position with ignition switch OFF. Key unlock solenoid When selector lever is not in P position with ignition switch OFF.
10 (W/B)
CVT-211
Component Inspection
SHIFT LOCK SOLENOID
Check operation by applying battery voltage to the CVT device harness connector. CAUTION: Be sure to apply the voltage of the correct polarity to the respective terminals. Otherwise, the part may be damaged.
q
ECS00FCK
Connector M57
SCIA2005E
SCIA2006E
SCIA2046E
Connector M28
SCIA6460E
CVT-212
Check operation by applying battery voltage to key switch harness connector. CAUTION: Be careful not to cause burnout of the harness.
Connector M28 Terminal 2 (Battery voltage) - 1 (Ground)
CVT
SCIA6461E
KEY SWITCH
q
SCIA6462E
Check continuity between terminals of the stop lamp switch harness connector.
Condition When brake pedal is depressed When brake pedal is released Connector E116* or M114** Terminal 1-2 Continuity Yes No
K
SCIA2045E
Check stop lamp switch after adjusting brake pedal. Refer to BR-6, "Inspection and Adjustment" .
CVT-213
SCIA2284E
CAUTION: q Securely insert the hose into the air breather until it touches the bottom.
CVT-214
DIFFERENTIAL SIDE OIL SEAL DIFFERENTIAL SIDE OIL SEAL Removal and Installation
COMPONENTS
B
PFP:33111
A
ECS00FCM
CVT
G
SCIA2408E
1.
Transaxle assembly
2.
REMOVAL
1. 2. 3. Remove drive shaft assembly. Refer to FAX-8, "FRONT DRIVE SHAFT" . Remove transfer from transaxle assembly. Refer to TF-56, "Removal and Installation" . Remove differential side oil seal using a flat-bladed screwdriver. CAUTION: Be careful not to scratch transaxle case.
I
K
SCIA2412E
CVT-215
NOTE: The differential side oil seal pulling direction is used as the reference.
SCIA6620E
Drift to be used:
Location Transaxle case side (left) Converter housing side (right) Tool number: A ST33400001 KV40100621
SCIA6583E
2.
CAUTION: q When installing differential side oil seal, apply NISSAN CVT Fluid NS-2. q Do not reuse differential side oil seal. Reinstall any part removed. CAUTION: If lubricant leak has occurred, after finishing work, check fluid level. Refer to CVT-14, "Checking CVT Fluid" .
CVT-216
CVT FLUID COOLER SYSTEM CVT FLUID COOLER SYSTEM CVT Fluid Cooler Removal and Installation
COMPONENTS
B
PFP:21600
A
ECS00FCZ
CVT
SCIA6539E
1. 4. 7.
CVT fluid cooler bracket CVT fluid cooler bracket CVT fluid cooler hose (upper)
2. 5. 8.
3. 6. 9.
Radiator core support (LH) CVT fluid cooler hose (radiator to CVT fluid cooler bypass valve) CVT fluid cooler bypass valve
10. CVT fluid cooler hose (CVT fluid cooler bypass valve to transaxle)
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-8, "Components" .
REMOVAL
1. 2. Remove front bumper from vehicle. Refer to EI-17, "Removal and Installation" . Remove CVT fluid cooler hose (upper) (1) from CVT fluid cooler bypass valve (2).
M
SCIA6543E
CVT-217
SCIA6545E
4.
Remove CVT fluid cooler hose (lower) (1) from CVT fluid cooler (2).
SCIA6552E
5.
Remove CVT fluid cooler (1) from CVT fluid cooler bracket (2). : Nut (3)
SCIA6546E
6.
Remove CVT fluid cooler hose (upper) (1) from CVT fluid cooler (2).
SCIA6548E
CVT-218
CVT
D
SCIA6562E
Note the following instruction when inserting CVT fluid cooler hose (upper) into CVT fluid cooler bypass valve. When inserting CVT fluid cooler hose (upper) into CVT fluid cooler bypass valve, insert it so as to fit the paint mark (A). When inserting CVT fluid cooler hose (upper) into CVT fluid cooler, insert it with the paint mark (B) facing 45 degrees forward of the left side of the vehicle. Install a pawl of hose clamp (1) with it facing 45 degrees forward of the left side of the vehicle.
SCIA6563E
Insert a clip (1) into bracket mounting hole, and fix CVT fluid cooler hose (upper) securely.
K
SCIA6564E
Note the following instruction when inserting CVT fluid cooler hose (lower) into CVT fluid cooler. When inserting CVT fluid cooler hose (lower) into CVT fluid cooler, insert it so as to fit the paint mark (A). When inserting CVT fluid cooler hose (lower) into CVT fluid cooler, insert it with the paint mark (B) facing backward of the vehicle. Install a pawl of hose clamp (1) with it facing backward of the vehicle.
SCIA6568E
CVT-219
Note the following instruction when inserting CVT fluid cooler hose (lower) into CVT fluid cooler bypass valve. When inserting CVT fluid cooler hose (lower) into CVT fluid cooler bypass valve, insert it so as to fit the paint mark (A). When inserting CVT fluid cooler hose (lower) into CVT fluid cooler bypass valve, insert it with the paint mark (B) facing backward of the vehicle. Install a pawl of hose clamp (1) with it facing backward of the vehicle.
SCIA6569E
Install hoses clamp on the position of 5 mm (0.20 in) from the edge of CVT fluid cooler hose. Distance A: 5 mm (0.20 in)
SCIA6750E
ECS00FF4
SCIA6549E
3.
Remove CVT fluid cooler bracket (1) from radiator core support (LH) (2). : Bolt (1)
SCIA6554E
CVT-220
CVT
SCIA6555E
5.
Remove CVT fluid cooler bypass valve (1) from CVT fluid cooler bracket (2). : Bolt (2)
G
SCIA6556E
INSTALLATION
Note the following, and install in the reverse order of removal. q Note the following instruction when inserting CVT fluid cooler hose (radiator to CVT fluid cooler bypass valve) into CVT fluid cooler bypass valve. When inserting CVT fluid cooler hose (radiator to CVT fluid cooler bypass valve) into CVT fluid cooler bypass valve, insert it to the two-stage bulge. When inserting CVT fluid cooler hose (radiator to CVT fluid cooler bypass valve) into CVT fluid cooler bypass valve, insert it with the paint mark (A) facing 45 degrees backward of the downside of the vehicle. Install a pawl of hose clamp (1) with it facing 45 degrees backward of the downside of the vehicle.
q
K
SCIA6571E
Note the following instruction when inserting CVT fluid cooler hose (CVT fluid cooler bypass valve to transaxle) into CVT fluid cooler bypass valve. When inserting CVT fluid cooler hose (CVT fluid cooler bypass valve to transaxle) into CVT fluid cooler bypass valve, insert it to the two-stage bulge. When inserting CVT fluid cooler hose (CVT fluid cooler bypass valve to transaxle) into CVT fluid cooler bypass valve, insert it with the paint mark (A) facing 45 degrees leftward of the downside of the vehicle. Install a pawl of hose clamp (1) with it facing 45 degrees leftward of the downside of the vehicle.
SCIA6572E
CVT-221
Install hoses clamp (1) on the position of 5 mm (0.20 in) from the edge of CVT fluid cooler hose. Distance A: 5 mm (0.20 in)
Refer to CVT-219, "INSTALLATION" when installing CVT fluid cooler hose (upper and lower) to CVT fluid cooler bypass valve.
SCIA6750E
ECS00FD0
SCIA4344E
CVT-222
REMOVAL
WARNING: CVT Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure engine coolant escaping from the radiator. 1. Remove engine undercover. D 2. Drain engine coolant. Refer to CO-9, "Changing Engine Coolant" . CAUTION: Perform when the engine is cold. E 3. Remove air duct (inlet). Refer to EM-15, "Removal and Installation" . 4. Remove battery. Refer to SC-12, "Removal and Installation" . 5. Remove air cleaner case (upper and lower), resonator, mass air flow sensor and air duct assembly. Refer F to EM-15, "Removal and Installation" . 6. Remove fuse and fusible link block from battery bracket. G
I
SCIA2749E
7.
M
SCIA2750E
8.
SCIA2751E
CVT-223
SCIA2752E
11. Remove water bypass hose from water bypass pipe. Refer to CO-29, "Removal and Installation" .
SCIA4350E
12. Remove harness bracket and control cable bracket from transaxle assembly. Refer to CVT-202, "Removal and Installation" and CVT-222, "COMPONENTS" . 13. Remove inlet water hose and outlet water hose. Refer to CVT222, "COMPONENTS" . 14. Remove heater hose from heater pipe. Refer to CO-29, "Removal and Installation" . 15. Remove CVT fluid cooler valve assembly from transaxle assembly. Refer to CVT-222, "COMPONENTS" .
SCIA2753E
16. Remove heater hose from CVT fluid cooler valve assembly.
SCIA4349E
17. Remove CVT fluid cooler inlet tube assembly and CVT fluid cooler outlet tube assembly from CVT fluid cooler valve assembly.
SCIA4348E
CVT-224
COMPONENT INSPECTION
1.
Make sure that CVT fluid cooler valve is fully opened at room temperature. Standard Dimension A from CVT fluid cooler valve port end to tip of valve shaft (At room temperature): Approx 72.0 mm (2.835 in) or more
G
SCIA2711J
2.
Put CVT fluid cooler valve into a water-filled container, and then heat it up to 82C (180F) or more for 10 minutes or more.
SCIA2710E
3.
Make sure that CVT fluid cooler valve is fully closed. Standard Dimension A from CVT fluid cooler valve port end to tip of valve shaft (When heating to 82C (180F) or more for 10 minutes or more): Approx 66.5 mm (2.618 in) or less
L
SCIA2711J
CVT-225
SCIA6573E
1. 4. 7.
2. 5. 8.
3. 6. 9.
10. Copper washer 13. Hose clamp 16. Hose clamp 19. Transaxle assembly
11. Fluid cooler tube 14. Clip 17. LH engine mounting bracket 20. Rear engine mounting bracket
12. CVT fluid cooler hose 15. CVT fluid cooler hose 18. LH engine mounting insulator
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-8, "Components" .
: For tightening torque, refer to CVT-230, "INSTALLATION" .
CVT-226
TRANSAXLE ASSEMBLY
REMOVAL
A CAUTION: The transaxle assembly itself cannot be removed from the vehicle. Remove the transaxle assembly and engine assembly together from the vehicle. B 1. Disconnect the batter cable from the negative terminal. 2. Remove engine undercover. 3. Remove air guide. CVT 4. Remove exhaust front tube with power tool. Refer to EX-3, "Removal and Installation" . D
SCIA6476E
5.
I
SCIA6475E
6.
Turn crankshaft, and remove the four tightening nuts for drive plate and torque converter. CAUTION: The crankshaft should be rotated clockwise, viewed from the front of the engine.
SCIA1861E
7. 8.
Remove the six bolts in the figure. Remove transaxle assembly and engine assembly together from the vehicle. Refer to EM-104, "Removal and Installation" . 9. Remove drive shaft. Refer to FAX-11, "Removal and Installation (Left Side)" , FAX-13, "Removal and Installation (Right Side)" . CAUTION: Be sure to replace the differential side oil seal with new one at the every removal of drive shaft. Refer to CVT-215, "Removal and Installation" . 10. Remove transfer gusset. SCIA6016E 11. Remove transfer assembly. Refer to TF-56, "Removal and Installation" . CAUTION: Be sure to replace the differential side oil seal with new one (converter housing side only) at the every removal of transfer. Refer to CVT-215, "Removal and Installation" .
CVT-227
TRANSAXLE ASSEMBLY
12. Remove CVT fluid charging pipe. 13. Remove O-ring from CVT fluid charging pipe. 14. Disconnect harness connector and wire harness.
SCIA1894E
15. Remove crankshaft position sensor (POS) (1) from engine assembly. Refer to EM-28, "Removal and Installation" . CAUTION: q Do not subject it to impact by dropping or hitting it. q Do not disassemble. q Do not allow metal filings, etc., to get on the sensor's front edge magnetic area. q Do not place in an area affected by magnetism. 16. Remove starter motor. Refer to SC-16, "Removal and Installation" . 17. Remove CVT fluid cooler valve assembly (1). (With CVT fluid cooler tube assembly and heater hose). Refer to CVT-222, "CVT Fluid Cooler Valve Removal and Installation" . (A): Bolt (4) (B): Hose clamp (3)
SCIA6759E
SCIA6880E
18. Install slinger to transaxle assembly. 19. Remove rear gusset. 20. Remove LH engine mounting bracket and LH engine mounting insulator. 21. Remove front suspension member from transaxle assembly and engine assembly. Refer to EM-104, "Removal and Installation" . 22. Remove transaxle assembly fixing bolts with power tool.
SCIA4355E
CVT-228
TRANSAXLE ASSEMBLY
23. Remove transaxle assembly from engine assembly with a hoist. q Secure torque converter to prevent it from dropping.
A
CVT
SCIA6584E
After inserting a torque converter to a transaxle, be sure to check distance A to ensure it is within the reference value limit. Distance A: 14.0 mm (0.55 in) or more
SCIA6858E
CVT-229
TRANSAXLE ASSEMBLY
INSTALLATION
Note the following, and install in the reverse order of removal. q Set and screw in the drive plate location guide onto the stud bolts for the torque converter locate.
SCIA1871E
SCIA6881E
Rotate the drive plate for the hole of the drive plate locate to go down.
SCIA1872E
SCIA6584E
CVT-230
TRANSAXLE ASSEMBLY
q
When installing fluid cooler tube to transaxle assembly, assemble the part with the tube aligned with the rib.
CVT
SCIA2285E
D
q
When installing transaxle to the engine, attach the fixing bolts in accordance with the following standard.
Bolt No. Number of bolts Bolt length mm (in) Tightening torque Nm (kg-m, ft-lb) 1 1 52 (2.05) 2 2 36 (1.42) 75 (7.7, 55) 3 2 105 (4.13) 4 4 35 (1.38) 47 (4.8, 35)
G
SCIA6882E
Align the positions of tightening nuts for drive plate with those of the torque converter, and temporarily tighten the nuts. Then, tighten the nuts with the specified torque. : 51Nm (5.2 kg-m, 38 ft-lb) CAUTION: q When turning crankshaft, turn it clockwise as viewed from the front of the engine. q When tightening the tightening nuts for the torque converter after fixing the crankshaft pulley bolts, be sure to SCIA1861E confirm the tightening torque of the crankshaft pulley mounting bolts. Refer to EM-64, "INSTALLATION" . q After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that transaxle rotates freely without binding. Install crankshaft position sensor (POS). Refer to EM-28, "Removal and Installation" . After completing installation, check for fluid leakage, fluid level, and the positions of CVT. Refer to CVT-14, "Checking CVT Fluid" , CVT-204, "Adjustment of CVT Position" , CVT-205, "Checking of CVT Position" . When replacing the CVT assembly, erase EEP ROM in TCM. Refer to CVT-8, "Precautions for TCM and CVT Assembly Replacement" .
q q
CVT-231
SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) General Specifications
VQ35DE engine Applied model CVT model CVT assembly Model code number D range Transmission gear ratio Reverse Final drive Recommended fluid Fluid capacity
q q
PFP:00030
ECS00FCQ
4WD RE0F09A 1XD0A Variable 1.766 5.173 NISSAN CVT fluid NS-2*1 10.0 liter (8-3/4 Imp qt)
CAUTION: Use only Genuine NISSAN CVT fluid NS-2. Do not mix with other fluid. Using CVT fluid other than Genuine NISSAN CVT fluid NS-2 will deteriorate in driveability and CVT durability, and may damage the CVT, which is not covered by the warranty.
ECS00FCR
CAUTION: Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall Speed
Stall speed 2,700 - 3,250 rpm
ECS00FCS
Line Pressure
Engine Engine speed At idle speed VQ35DE At stall speed *1 : Reference values Line pressure kPa (kg/cm2 , psi) R, D positions 750 (7.65, 108.8) 5,700 (58.14, 826.5)*1
ECS00FCT
Solenoid Valves
Name Pressure control solenoid valve B (Secondary pressure solenoid valve) Pressure control solenoid valve A (Line pressure solenoid valve) Torque converter clutch solenoid valve Lock-up select solenoid valve 6 - 19 3-9 Resistance (Approx.) () Terminal 3 2 12 13
ECS00FCU
CVT-232
A
Resistance (Approx.) (k)
CVT
CVT-233
CVT-234