MTR3000 Product Planner Ver 8c Source
MTR3000 Product Planner Ver 8c Source
TABLE OF CONTENTS
PURPOSE AND SCOPE ....................................................................................................................i ACRONYMS AND ABBREVIATIONS ....................................................................................... vii MTR3000 INTRODUCTION............................................................................................................9 MTR3000 Overview ......................................................................................................................10 MTR2000 MOTOTRBO UPGRADE (Non-RTTE countries only) ..............................................15 Overview ........................................................................................................................................15 MTR2000 MOTOTRBO Upgrade Specs.......................................................................................15 MTR2000 MOTOTRBO Upgrade Installation ..............................................................................16 Compatibility..................................................................................................................................16 MTR2000 vs. MTR3000 COMPARISON......................................................................................19 SPECIFICATIONS..........................................................................................................................26 Specification Definitions................................................................................................................26 MTR3000 Base Station/Repeater Specifications ...........................................................................28 Power and Energy Consumption....................................................................................................31 Power and Energy Consumption Curves .......................................................................................31 Transmitter Noise...........................................................................................................................44 Receiver Interference Rejection .....................................................................................................44 STANDARDS ...................................................................................................................................45 Altitude Derating............................................................................................................................47 RFDS OPTIONS ..............................................................................................................................48 RFDS Component Specifications...................................................................................................48 X182 Duplexers (UHF)..............................................................................................................48 X182 Duplexer (800MHz) .........................................................................................................51 X265 Base Station/Repeater Preselector (UHF) ........................................................................53 X676 External Dual Circulator ......................................................................................................55 X676 (800MHz) .............................................................................................................................57 Minimum Antenna Isolation ..........................................................................................................59 MODULES........................................................................................................................................60 Power Supply Module....................................................................................................................60 Power Supply Connections ........................................................................................................60 PS Containment..........................................................................................................................61 Performance Specifications........................................................................................................61 Power Amplifier Module ...............................................................................................................63 Power Amplifier Connections....................................................................................................64 PA Containment .........................................................................................................................64 PA Basic Electrical Performance ...............................................................................................64 Power Meter Accuracy...............................................................................................................64 Receiver Module ............................................................................................................................65 Receiver Connections.................................................................................................................65 Receiver Basic Electrical Performance ......................................................................................66 Exciter Module...............................................................................................................................67 Exciter Connections ...................................................................................................................67 Exciter Basic Electrical Performance.........................................................................................68 Station Control Module..................................................................................................................69 ii
Status Indicators & Buttons............................................................................................................70 MTR3000 Controller Front Panel Connectors ...............................................................................70 MTR3000 Controller Software Controlled LEDs......................................................................71 MTR3000 Controller Hardware Controlled LEDs.....................................................................71 Wireline Board ...............................................................................................................................72 MTR3000 INSTALLATION...........................................................................................................75 Rack and Cabinet Installation, Placement & Site Design ..............................................................75 Site Design .................................................................................................................................75 Installation Considerations.........................................................................................................76 Seismic Reliability .....................................................................................................................76 Cabinet Stacking ........................................................................................................................76 Cabinet Mount............................................................................................................................76 Rack Mount ................................................................................................................................77 Adding MTR3000 and/or Upgraded MTR2000 stations to MTR2000 sites .................................77 Analog Radio Interface ..............................................................................................................78 Wireline Interface.......................................................................................................................78 GPIO and Audio Configuration .................................................................................................79 Incompatible MTR2000 FRUs and Boards................................................................................79 MTR3000 and Upgraded MTR2000 Analog Radio Interface Differences................................79 MTR3000 and Upgraded MTR2000 Analog Radio RF Performance Differences....................80 Station Grounding ......................................................................................................................80 Backplane Connections ..................................................................................................................80 POWER SOURCE ...........................................................................................................................83 Block Diagram of AC & DC Flow.................................................................................................83 Power Rollback ..............................................................................................................................84 Number of Battery Cells ................................................................................................................86 Battery Charging System and Wire Gauge Determination ............................................................86 AC Breaker Recommendation .......................................................................................................86 DC Breaker Recommendation .......................................................................................................87 STATION MAINTENANCE & ALIGNMENT............................................................................88 Routine Maintenance......................................................................................................................88 Alignment.......................................................................................................................................88 Customer Programming Software..................................................................................................88 Base Station Software and Future Software Upgrades ..................................................................89 MTR3000 ORDERING GUIDE .....................................................................................................91 MTR3000 Base Station/Repeater Ordering Matrix .......................................................................91 MTR3000 Base Station/Repeater Model and Option Descriptions ...............................................93 Main Model Description ............................................................................................................93 Frequency Band and Power Level .............................................................................................93 Base Station/Repeater Software & Features ..................................................................................93 Customer Programming Software (CPS) ...................................................................................94 Software Features.......................................................................................................................94 Peripheral Options..........................................................................................................................95 Duplexer .....................................................................................................................................95 Narrow Preselector.....................................................................................................................95 Antenna Relay ............................................................................................................................97 DC Power Cables .......................................................................................................................97 Battery Charging ........................................................................................................................97 iii
International Power Cables ........................................................................................................97 Mounting Hardware ...................................................................................................................97 Communication / Reference Cables...........................................................................................98 Racks and Cabinets ....................................................................................................................99 MTR2000 MOTOTRBO UPGRADE ORDERING MATRIX ..................................................101 MTR2000 MOTOTRBO UPGRADE ORDERING GUIDE......................................................102 Main Model ..................................................................................................................................102 Frequency Band and Power Level ...............................................................................................102 Base Station/Repeater Software & Features ................................................................................102 Customer Programming Software (CPS) .................................................................................103 Software Features.....................................................................................................................103 Communication Cable..................................................................................................................103 Manuals ........................................................................................................................................104 Field Replacement Units (FRUs)................................................................................................104 Ordering tips.................................................................................................................................105 Checking the Order ......................................................................................................................105 Other Helpful Material .................................................................................................................105
iv
LIST OF FIGURES
Figure 1. MTR3000 Base Station/Repeater Front View ...................................................................13 Figure 2. MTR3000 Base Station/Repeater Front View (Without Cover) .......................................13 Figure 3. MTR3000 Base Station/Repeater Rear View ....................................................................14 Figure 4. MTR2000 MOTOTRBO Upgrade Kit Contents ...............................................................17 Figure 5. UHF R1 and R2 --- AC Power Consumption Plots ...........................................................32 Figure 6. UHF R1 and R2 --- AC Current Draw Plots......................................................................33 Figure 7. UHF R1 and R2 --- DC Power Consumption Plots ...........................................................34 Figure 8. UHF R1 and R2 -DC Current Draw Plots .........................................................................35 Figure 9. UHF Duplexer View..........................................................................................................48 Figure 10. UHF Duplexer Plots (T-band) TX=471 MHz, RX=474 MHz ........................................49 Figure 11. UHF Duplexer Plots 5 MHz T/R Spacing .......................................................................50 Figure 12. UHF Base Station/Repeater Preselector ..........................................................................53 Figure 13. UHF Base Station/Repeater Preselector Plots (f=467 MHz)...........................................54 Figure 14. UHF External Dual Circulator Photo...............................................................................55 Figure 15. External Dual Circulator Plots (<470 MHz)....................................................................56 Figure 16. Power Supply Module .....................................................................................................61 Figure 17. MTR3000 Power Amplifier Module ...............................................................................63 Figure 18. Receiver Module..............................................................................................................65 Figure 19. Exciter Module ................................................................................................................67 Figure 20. Station Control Module ...................................................................................................69 Figure 21. Station Control Module (Front View) .............................................................................70 Figure 22. MTR3000 Base Station/Repeater BackplaneView..........................................................80 Figure 23. AC and DC Power Distribution, MTR3000 Base Station/Repeater................................83 Figure 24. UHF RF Power Out Rollback Curve ...............................................................................84 Figure 25. Detailed Rack Specifications .........................................................................................100
LIST OF TABLES
Table 1. Migration Path Considerations............................................................................................15 Table 2. MTR3000 System Compatibility ........................................................................................17 Table 3. MTR3000 Station Compatibility.........................................................................................18 Table 4. MTR3000 Site Equipment Compatibility ...........................................................................18 Table 5. MTR2000 vs. MTR3000 Comparison ................................................................................19 Table 6. Detailed MTR2000 to MTR3000 Analog Comparison ......................................................21 Table 7. Upgrade Compatibility........................................................................................................24 Table 8. MTR3000 Base Station/Repeater General Specifications ..................................................28 Table 9. MTR3000 Base Station/Repeater Transmitter Specifications ............................................29 Table 10. MTR3000 Base Station/Repeater Receiver Specifications...............................................30 Table 11. Power Consumption ..........................................................................................................31 Table 12. Transmitter Noise Performance ........................................................................................44 Table 13. Receiver Interference Rejection........................................................................................44 Table 14. Standards ...........................................................................................................................45 Table 15. UHF Duplexer Specifications ...........................................................................................49 Table 16. UHF Base UHF Base Station/Repeater Preselector Specifications ..................................53 Table 17. UHF External Dual Circulator Specifications...................................................................56 Table 18. Power Supply Performance Specifications (AC)..............................................................61 Table 19. Power Supply Performance Specifications (DC)..............................................................62 Table 20. Power Supply Performance Specifications (Switching) ...................................................62 Table 21. Power Amplifier Performance Specification ....................................................................64 Table 22: Receiver Performance Specification.................................................................................66 Table 23. Exciter Performance Specification....................................................................................68 Table 24. Table Controller Connector and Switch Definitions.........Error! Bookmark not defined. Table 25. Controller Definition and Meaning...................................................................................71 Table 26. Controller Definition and Meaning...................................................................................71 Table 27. MTR3000 Base Station/Repeater Backplane Connectors.................................................81 Table 28. MTR3000 J7 Aux Backplane Connections.......................................................................82 Table 29. MTR3000 J5 System Backplane Connections..................................................................82 Table 30. MTR3000 J5 System Backplane Connections..................................................................86 Table 31. MTR3000 Base Station/Repeater Ordering Matrix ..........................................................91 Table 32. MTR2000 MOTOTRBO Upgrade..................................................................................101 Table 33. FRUs for MTR3000 and MTR2000 MOTOTRBO Upgrade ........................................104
vi
OMAP PA PIM PL ppb ppm PTT RDAC RF RFDS RMS RoHS RU RX SCM SPI TCXO TDMA TIA TRC TX USB V VAC VCO VDC VSWR W XCVR
Open Multimedia Application Platform Power Amplifier Passive Intermodulation Private Line Parts Per Billion Parts Per Million Push to Talk Repeater Diagnostics and Control Radio Frequency Radio Frequency Distribution System Root Mean Squared Reduction of Hazardous Substances Rack Unit Receive Station Control Module Serial Peripheral Interface Temperature Compensated Crystal Oscillator Time Division Multiple Access Telecommunications Industry Association Tone Remote Control Transmit Universal Serial Bus Volt Volts Alternating Current Voltage Controlled Oscillator Volts Direct Current Voltage Standing Wave Ratio Watts Transceiver
viii
MTR3000 Programmed in MOTOTRBO Mode Supports two simultaneous voice paths in digital 12.5 kHz TDMA (6.25e compliant) Divides existing channel into two timeslots delivering twice the capacity through a single repeater Supports MOTOTRBO IP Site Connect for increased wide area coverage Supports MOTOTRBO Capacity Plus single site Trunking without a separate hardware controller Support MOTOTRBO Connect Plus multi site trunking (UHF Only) with a separate hardware controller Supports MOTOTRBO Dynamic Mix Mode to facilitate the analog to digital migration in conventional repeater applications Supports MOTOTRBO Transmit Interrupt for greater subscriber unit control and flexibility
MTR3000 Serviceability Repeater diagnostic and control software provides remote or local site monitoring Easy to replace components with functionally separate Field Replaceable Units (FRU) Software based design simplifies feature upgrades Easy access to station ports (no need to remove the front panel) shortening installation and maintenance time For ease of installation, minimal station alignment is needed. NEW! Backed by Motorolas 2-year standard warranty
Total Cost of Ownership Analog Conventional, Digital Conventional are standard in one base station without the cost of additional software Twice the spectral efficiency; One frequency pair provides 2 logical voice paths Effectively twice the power efficiency as compared to 2 analog stations when operating in Digital mode Integrated Components optimizes expensive site space: - One physical station provides the capacity of two in Digital Mode
Station Mechanics Compact design MTR3000 dimensions, 3 Rack Units (5.25 or 13.3 cm), optimizes expensive site space efficiently Lightweight (40 lbs. /19 kg.) Standard EIA 19 rack mount configuration
MTR3000 Overview
The Motorola MTR3000 Base Station/Repeater provides a modular, flexible analog and digital station design for today's communication systems and for the future. The station is available for use in Analog Conventional, Digital Conventional (MOTOTRBO), MOTOTRBO Capacity Plus Trunking and Connect Plus (UHF Only) multi site trunking configurations. When configured for analog operation, MTR3000 can either be configured as a base station or as a repeater. As a repeater, it listens on one uplink frequency, and then re-transmits on a downlink frequency, thus providing the RF interface to the field subscribers. When configured as a base station, MTR3000 is designed to operate with most existing analog systems. When configured for digital operation, the base station/repeater offers additional services. The digital base station/repeater operates in TDMA mode, which essentially divides one channel into two virtual channels using time slots; therefore the user capacity is doubled. The base station/repeater utilizes embedded signaling to inform the field radios of the busy/idle status of each channel (time slot), the type of traffic, and even the source and destination information. 10
Note: When configured in Digital Mode, MTR3000 can only be used as a repeater. At any given time, MTR3000 either operates as a digital repeater or as an analog repeater. The MTR3000 base station/repeater is divided into functional modules that separate the frequency band specific and transmitter power specific circuits from other circuits and has separate modules for the control interface. These modules are self contained functional blocks with module-specific alarms. This design facilitates the field replaceable unit (FRU) concept of field repair to maximize system uptime. The description of the FRUs is as follows: The Receiver FRU is a dual heterodyne receiver which receives the RF signal from the subscribers transmitter. It then converts the resulting final intermediate frequency (IF) from an analog signal to that of a digital word. Finally, the receiver delivers the digital word, via the data bus, to the SCM for demodulation. Additionally, the receiver also provides its own metering and diagnostics via software, as well as a self-contained calibration (no field tuning needed). The Exciter FRU converts a two-port base band data signal, sent over the data bus from the SCM, to an analog signal representation. The analog signal then modulates a low power RF transmitter carrier that is generated by the exciter. The low power modulated RF carrier is then amplified and delivered to the PA for further amplification. The Exciter and PA constitute the transmitter of the MTR3000. Additionally, the exciter also provides its own metering and diagnostics via software, as well as a self-contained calibration (no field tuning needed). The heart of the SCM FRU is that of two Texas Instruments OMAP series processors, with each OMAP containing an ARM Host and a C55 DSP processor. One of the two OMAP processors is dedicated to the receiver DSP operations, while the other OMAP provides for all other functionality, which includes the transmitter functions. In general the SCM provides for the entire coordination of the base station/repeater functions, but more specifically, the SCM provides for the following functionality: Contains and runs the preloaded base station/repeater software. Manages inbound and outbound RF and Audio traffic. Provides external speaker and microphone ports (analog only) Provides an on-board USB port for local configuring, alignment and diagnostics via the following applications: o Customer Programming Software (CPS), o Tuner application o Repeater Diagnostic and Control (RDAC) software. Provides an Ethernet port for IP site connectivity and remote RDAC. Provides GPIO connectivity for 3rd party controller interfaces. Provides analog base station audio connectivity. Data and Control to the receiver Data and Control to the exciter Control of the PAs set power 11
Generates the internal station frequency reference. Provides control of the front panel status indicators.
The PA FRU amplifies the low level modulated RF signal from the exciter module. It then delivers the amplified signal to the transmitter antenna port at the rated power of the base station/repeater, or less if the customer desires, for transmission to the subscribers receiver. In addition to its primary task of amplification, the PA provides the following hardware functions for the base station/repeaters: Harmonic attenuation Intermodulation attenuation (IMA) suppression VSWR detection RF power control (primary means). Self contained cooling fan and control circuit Diagnostics Power rollback for temperature, VSWR, and voltage Self-Contained calibration (No field alignment for MTR3000 PAs only)
The PS FRU provides DC power to the receiver, exciter, SCM, PA, and select third party controllers via one or more of the three DC output taps; 28.6VDC, 14.2VDC, and 5.1VDC. It can also provide auxiliary power to a number of third party controllers. Additionally, it can operate in three different input modes: AC Input Only DC Input Only AC with Battery Revert
In addition to providing power to the noted FRUs and controllers, the PS also provides for the following: AC Failure detect signaling to the SCM Output over-current protection for all three outputs Self contained cooling fan and control circuit Thermal shut down if the environmental temperatures exceed the cooling capacity afforded by the fan. Further details can be found in the individual Theory of Operation sections of the respective FRUs.
The Wireline FRU provides the connection to an analog audio source/sink (such as a console) to the MTR3000 Base Station/Repeater. Specifically, the Wireline board provides for the following: Tone Remote Control DC Remote Control 4-wire balanced audio connection 2-wire balanced audio connection
12
13
14
Hardware/Software Needed:
MTR2000 MOTOTRBO Upgrade Kit (T2003) MTR2000 MOTOTRBO Upgrade Kit (T2003) & Software Programming MTR2000 MOTOTRBO Upgrade Kit (T2003) & Capacity Plus Software Upgrade (HKVN4045A) Software Programming Capacity Plus Software Upgrade (HKVN4045A) MTR2000 MOTOTRBO Upgrade Kit (T2003) & Capacity Plus Software Upgrade (HKVN4045A) MTR2000 MOTOTRBO Upgrade Kit (T2003) & Connect Plus Software Upgrade
15
Compatibility
The following charts identify the system types, stations, and controllers that are compatible with the MTR3000. Table 5 and Table 6 outline a direct feature comparison between the MTR3000 and the MTR2000. It is imperative that the differences between the two stations are understood when an MTR3000 is to be purchased for use in an analog system, as not all analog features that were offered with the MTR2000 are available with the MTR3000. Furthermore, the base station audio and control interface on the backplane has changed between the MTR3000 and MTR2000 stations. These interface differences are noted in the Adding MTR3000 and/or Upgraded MTR2000 stations to MTR2000 sites section of this manual. Additionally, the MTR3000 platform offers a MTR2000 MOTOTRBO UPGRADE for existing high-power UHF MTR2000 stations. When a MTR2000 station has employed the MOTOTRBO Upgrade Digital Kit, the upgraded MTR2000 station will provide all digital functionality that a factory new MTR3000 provides. Analog features offered in an upgraded MTR2000 station are identical to that of a factory new MTR3000, however, there are subtle differences in the analog connectivity at the J7 backplane connection between an upgraded MTR2000 station and that of a factory new MTR30000 station. These differences are noted in the Adding MTR3000 and/or Upgraded MTR2000 stations to MTR2000 sites section of this manual. Note: Since analog features will be lost with respect to the non-upgraded MTR2000, it is not recommended to purchase a MOTOTRBO Digital Upgrade Kit for the MTR2000 if one expects to operate the upgraded MTR2000 in analog mode. Upgrading the station and operating in analog mode may be a temporary configuration while migrating the subscribers. See Table 7 for specific configurations that are upgradeable. The MOTOTRBO Upgrade Kit consists of the following individual items: MTR3000 Exciter FRU MTR3000 Receiver FRU MTR3000 Station Control Module FRU MTR3000 Front Bezel 16
Preloaded MOTOTRBO SW TORX screws T20 bit size required. (Used to assemble the three FRUs to one another) MTR3000 FCC upgrade label (Use to cover the MTR2000 FCC label located on the backplane)
Privacy Plus/SmartNet Digital Trunking MOTOTRBO Capacity Plus MOTOTRBO Connect Plus (UHF Only) ASTRO (P25)
No Yes Yes No
17
18
MTR2000
Yes No Yes No Yes No Yes Yes Yes Yes No No No No Yes Yes Yes Yes No Yes Yes Yes Yes No Yes 32 12.5/15/20/25/30kHz No
MTR3000
Yes Yes Yes No Yes Yes Future Release Yes Yes No Yes Yes Yes Yes Future Release Future Release No Yes Yes Yes Yes No Yes Yes Yes 16 12.5/15/20/25/30kHz Yes
19
MTR2000
No Yes Yes Yes Yes Yes Yes Yes Yes Yes 12 GP0 and 11 GPI (Optional) Yes (Optional) Yes No No No No No No No No No Yes No
MTR3000
Yes Yes Yes Yes No Future Release Yes Yes Yes No 7 GPIO and 2 GPI (Standard) Yes (Standard) Future Release Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes
20
The following chart is a detailed analog comparison between the MTR2000 and MTR3000.
Table 6. Detailed MTR2000 to MTR3000 Analog Comparison Detailed Base Station/Repeater Features
Analog Voice Receive and Transmit (Wireline) TX pre-emphasis RX de-emphasis RX PL filter RX Activation selection (PL, DPL, CSQ, PL& CSQ) Rx Activation selection (Select 5, Single Tone) Analog Voice Receive and Transmit (E&M via GPIO) TX pre-emphasis RX de-emphasis RX PL filter RX Activation selection (PL, DPL, CSQ, PL& CSQ) RX Activation selection (Select 5/Single Tone) In-cabinet repeat Activation selection (PL, DPL, CSQ, PL & CSQ, DPL & CSQ) Activation selection (Select 5/Single Tone) Hold in selection (PL, DPL, CSQ, PL & CSQ, DPL & CSQ) Hold off Delay Audio Boost Deactivation Selection (Select 5/Single Tone) Noise Cancellation Companding TX Priority (Programmable) Base operation Fall back in-cabinet repeat Same RX & TX freq (simplex) Different RX & TX freq Antenna Relay PTT Types Repeat path Rx Audio One Ext PTT (Console, Phone Patch, etc.) Dedicated MIC PTT Dedicated External Audio Connections (Local/Phone/Trunked Data) Multiple Channels Multiple Channels - up to 16 Multiple Access Code Tables - up to 16 Channel set up parameters Repeater timeout timer Repeater drop out delay (Hang Time) Selectable Output power normal/battery backup Console wireline Timeout timer Local timeout timer Phone patch timeout timer
MTR2000
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
MTR3000
Yes Yes Future Release Future Release No Yes Yes Yes Yes No Yes No No No Yes No Yes Yes Yes Future Release Future Release Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Future Release Yes No
21
Detailed MTR2000 to MTR3000 Analog Comparison (Continued) Detailed Base Station/Repeater Features
PL/DPL Types Motorola non-standard PL set Motorola standard PL set Selection of CSQ, PL, DPL Standard PL /DPL set Base Station Identification Morse code ID (polite) Morse code ID (not polite) Programmable timer Remote Control via external adapter DC Remote Control (DRC) Binary Remote Control Tone Remote Control (TRC) Console Commands via Integrated tone remote control Repeater Setup/Knockdown Channel Change PL/DPL Change Transmit and Receive PL/DPL On/OFF Monitor Console Commands via Integrated DC remote control Channel Change Monitor External Inputs External Frequency Reference Capability External PTT Monitor Repeater set up and knockdown Unbalanced RX and TX audio Microphone TX inhibit (called disabled in MOTOTRBO) RX Inhibit Wildcard 2-wire and 4-wire Telco compatible External Outputs CSQ Indication Analog RSSI (Receive Signal Strength Indicator) Speaker connection Carrier operator relay (Dry Contact) 2-wire and 4-wire Telco compatible Service Features Station Log Critical failure (Alarms and Events) HW and SW version screens Station Status RSSI (Receive signal strength indication) Hardware Metering screens
MTR2000
Yes Yes Yes Yes Yes No Yes Yes N/A N/A Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes RSS Yes Yes Yes Yes Yes
MTR3000
Yes Yes Yes Yes Yes Yes Yes Future Release No Yes Yes Yes Future Release Future Release Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Future Release Yes CPS, Tuner and RDAC Yes Yes Yes Yes No
22
Detailed MTR2000 to MTR3000 Analog Comparison (Continued) Detailed Base Station/Repeater Features
Miscellaneous Deviation Control Full Duplex Half Duplex TX wireline squelch Auto Level Control (ALC) wireline Tx and Rx audio notch Cross Banding Alarm Tones Options X371 Antenna Relay Phone Patch (used to be MTRI) Selectable Fallback in cabinet repeat Voting X269 Voting Option (included in X777) X157 Enhanced Wild Card Wildcard Options Wildcard Main stand-by Receive Only Configuration Receiver
MTR2000
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
MTR3000
Yes Yes Yes Yes Yes Yes No No Yes Yes Future Release Future Release No No Yes No
23
Considerations before beginning a migration plan The purpose of an MTR2000 MOTOTRBO upgrade is to allow users to migrate to MOTOTRBO digital without having to purchase an entirely new station. When upgrading to an MTR3000, use the following chart to ensure features and/or functionality is supported.
Table 7. Upgrade Compatibility MTR2000 Analog Upgrade Capability MTR2000 Feature Name
Analog Air Interface Conventional Privacy Plus/Smartnet Analog Station Operation Base Station Repeater Receive Only Channel Configuration Simplex Half Duplex Full Duplex Frequency VHF 136-154 VHF 150-174 UHF 330-403 UHF 403-470 800 MHz 900 MHz Network Interface 4-wire (E&M via GPIO) 4-wire (E&M) Analog wireline Voting Analog Voting Transmitter Capability Low Power (30/40W) High Power (75/100W) Custom Programming Aux I/O Wildcard Programming Hardware Peripheral compatability Duplexer Preselector Circulator External Frequency Reference Antenna Relay Argus Battery Charger
Upgrade to MTR3000
Yes* No
Yes* Yes* No Future Release Yes Yes Future Release Future Release No Yes Yes Yes Yes Yes Yes Future Release Yes Yes No No Yes Yes Yes Yes Yes Yes
24
Note: An Upgraded MTR2000 can be used in analog mode. However, since some analog functionality would be lost in this transition, this application would be best applied to a customer who intends to migrate to MOTOTRBO at some time in the future.
25
SPECIFICATIONS
Specification Definitions
Listed alphabetically are the definitions of some of the specifications described above. Information on whether the preferred specification would be smaller or larger is also given. 1) Adjacent Channel Power Ratio (Decibels/ dB): A measure of the level of undesired transmit signal that falls within the adjacent frequency channel. Often this is limited by the modulation type rather than hardware or software. A larger number is better. 2) Adjacent Channel Rejection {Selectivity} (Decibels/ dB)Ability of the receiver to detect the desired signal, while rejecting signals on adjacent channels. The benefit is less interference. The preferred specification is larger. Effective system performance may be limited by the interfering subscriber units transmitter noise or modulation characteristics 3) Bandwidth: As it applies to T-T or R-R (Megahertz/ MHz)The maximum frequency separation from the lowest frequency to the highest frequency without degradation of specifications. The preferred specification for multi-channel base stations/repeaters should be wide enough to include all the channels that are used, depending upon the application. 4) Bandwidth: As it applies to T-R Spacing (Megahertz/ MHz)The specified frequency separation between the transmitter and receiver is band dependent. The preferred specification is generally smaller, although it depends upon the specific site requirements. 5) Bit Error Rate Floor (%): A measure of the receivers ability to detect and decode strong signals accurately. A small percentage is better. 6) Conducted Spurious Emissions (dBm): Undesired receiver output signals (on the antenna port). The benefit is reduced interference with other base stations/repeaters nearby. The preferred specification is a more negative number. 7) Co-Channel Rejection (Decibels/ dB): Ability of the receiver to reject on channel interference. This specification is usually determined by the modulation type. A smaller number is better. 8) Electronic Bandwidth: Operating range that can be obtained without any mechanical adjustments, such as tuning screws. Larger number is better. Full bandwidth is best. 9) Emissions Designator: An FCC designator describing bandwidth and modulation type. 10) Frequency Stability (+/-% OR parts per million/ppm OR parts per billion/ppb): The ability to stay on the assigned frequency over a temperature range of -30 to +60C. The benefit is increased coverage, less interference and reduced background noise. The preferred specification is smaller, which implies a greater stability. 11) Harmonic Emissions Attenuation (Decibels/dB): Similar to spurious outputs (described below); multiples of the frequency of the final power amplifier (transmitter). The benefit is reduced interference to nearby base stations/repeaters. The preferred specification is a larger number. 12) Intermodulation Attenuation (Decibels/ dB): Reduces transmitter intermodulation by preventing undesired signals from entering into the transmitter's PA. This is 26
accomplished by using circulators or isolators. The preferred specification is larger. This specification is especially important at dense sites. 13) FSK Error (%): A measure of the transmitters ability to accurately produce a digitally modulated signal. A smaller percentage is better. 14) Receiver Intermodulation/IMR (Decibels/ dB)Mixing of undesired signals which interferes with the desired signal. This is important if the R-R bandwidth is large. The benefit is less interference. The preferred specification is larger. 15) Sensitivity (Microvolts/V or dBm)The ability of the receiver to detect and amplify weak signals. The benefit is increased coverage. 12 decibels SINAD is the threshold for intelligible analog voice communications. The preferred specification is smaller. 5% bit error rate is the threshold for intelligible digital voice communication. 16) Signal Displacement Bandwidth (Off-Channel Acceptance) (kHz)The amount the signal can be off the tuned frequency and still be received. The preferred specification is larger and must be at least as good as the frequency stability of the transmitting subscriber units. 17) Spurious Emissions (Decibels/ dB)Undesired transmitter output signals. The benefit is reduced interference with other base stations/repeaters nearby. The preferred specification is a larger number. 18) Spurious (Image) Response (Decibels/ dB)Ability of the receiver to reject certain types of undesired or interfering signals related to the operating frequency. The preferred specification is larger. For analog FM, TIA603D standards and methods are used unless otherwise noted for analog specs. Specifications regarding digital modulation use TIA102 methods.
27
28
Adjacent Channel Power Ratio (25kHz/12.5kHz) Intermodulation Attenuation RF Output Connector RF Impedance FCC Designation
75dB / 60 dB 55 dB N female 50 Ohms Freq Range 406.1-470 MHz ABZ89FC4823 Freq Range 470-512 MHz ABZ89FC4825
* With AC input or DC input voltages in the range of 25.7V to 30.7V for UHF, and 24.7V to 30.7V for the 800/900MHz band.
29
Note: Specifications do not include optional equipment unless noted otherwise. All analog specifications are in reference to TIA603D unless noted otherwise. Specifications regarding digital modulation use TIA102 methods.
30
Band/Mode
UHF (403-470 MHz) Tx = 100W UHF (403-470 MHz) Tx = 100W UHF (470-524 MHz) Tx = 100W UHF (470-524 MHz) Tx = 100W UHF (403-470 MHz) Rx Mode UHF (403-470 MHz) Rx Mode UHF (470-524 MHz) Rx Mode UHF (470-524 MHz) Rx Mode 800/90MHz (850 870 MHz & 935 941 MHz) Tx = 100W 800/90MHz (850 870 MHz & 935 941 MHz) Tx = 100W 800/900MHz (806 825 MHz & 896 902 MHz) Rx Mode 800/900MHz (806 825 MHz & 896 902 MHz) Rx Mode
31
AC Power (watts)
250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 110 Tx Power (watts) 403MHz 437MHz 470MHz
10
20
30
40
50
60
70
80
90
100
110
300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 110 Tx Power (watts) 470MHz 497MHz 524MHz
10
20
30
40
50
60
70
80
90
100
110
300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 110 Tx Power (watts) 470MHz 497MHz 524MHz
10
20
30
40
50
60
70
80
90
100
110
32
20
30
40
50
60
70
80
90
100
110
33
30
40
50
60
70
80
90
100
110
250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 110 Tx Power (watts) 470MHz 497MHz 524MHz
10
20
30
40
50
60
70
80
90
100
110
300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 110 Tx Power (watts) 470MHz 497MHz 524MHz
10
20
30
40
50
60
70
80
90
100
110
34
10
20
30
40
50
60
70
80
90
100
110
30
40
50
60
70
80
90
100
110
30
40
50
60
70
80
90
100
110
10
20
30
40
50
60
70
80
90
100
110
35
36
37
38
39
40
41
42
43
Transmitter Noise
The following table provides detailed information on the noise characteristics of the MTR3000 transmitter. This data is at the power amplifier output connector, so it includes no external filters or peripherals of any kind.
Table 12. Transmitter Noise Performance BAND: Offset (kHz)
100 500 1000 3000 > 5000
UHF R1 (dBc/Hz)
-136 -150 -152 -157 -157
UHF R2 (dBc/Hz)
-136 -150 -152 -157 -157
800/900MHz (dBc/Hz)
-136 -150 -152 -157 -157
44
STANDARDS
MTR3000 meets or exceeds the following standards:
Table 14. Standards
Standard TIA/EIA-603-D ETSI EN 300 086 - 1 ETSI EN 300 113 - 1 RTTE Australia AS 3516.2:1998 AS/NZS 3548:1995 AS/NZS 4251.1:1994 AS/NZS 4252.1:1994 R56 EN 60529 ETS 300 753 EN 61000-3-2 EN 61000-3-3 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-7 IEC 61000-4-8 IEC 61000-4-9 IEC 61000-4-10 Description Analog FM performance Analog FM performance Digital performance European Uniformity Directive Siting Guidelines Electromagnetic Compatibility Emissions Immunity Standard & Guidelines for Communications Sites Protection provided by enclosures Acoustic noise EMC limits for harmonic current emissions Limitations of voltage changes, voltage fluctuations & flicker Electrostatic discharge immunity Radiated RF EM field immunity Electrical fast transient/burst immunity Surge immunity test Immunity to conducted disturbances induced by RF fields Mains EMC: Harmonic & Interharmonic Currents Power frequency magnetic field immunity Pulse magnetic immunity Damp oscillatory immunity Class or Revision
68-61089E50 iss B IP20 Meets classification of: Attended telecommunications equipment rooms
45
Standards (Continued)
Standard Description Class or Revision Batteries operating above 24VDC: Dips: 40% & 70% voltage, 0.5 and 1 cycle, no batteries: no degradation of performance or loss of function. 40% & 70% voltage, >1 cycle, no batteries: self recovery after disturbance ceases. 40% & 70% voltage, >1 cycle, with batteries: no degradation of performance or loss of function (station reverts to batteries). Variations: 70% voltage (2s decrease transition, 1s at 70%, 2s increase transition) no batteries: no degradation of performance or loss of function in RX mode. Self recovery after disturbance ceases in TX mode. 40% voltage (2s decrease transition, 1s at 40%, 2s increase transition) with batteries: no degradation of performance or loss of function. Level 3 Level 3 Level 3 Level 3 Level 3 AC off: Dips: 40% & 70% voltage, 1 ms: no degradation of performance or loss of function. 40% & 70% voltage, >3 ms: self recovery after disturbance ceases. Short Interruptions: 0% voltage, 1 ms: no degradation of performance or loss of function. 0% voltage, >3 ms: self recovery after disturbance ceases. Variations: 80% & 120% voltage, 3 s: no degradation of performance or loss of function.
IEC 61000-4-11
IEC 61000-4-12 IEC 61000-4-14 IEC 61000-4-16 IEC 61000-4-17 IEC 61000-4-28
Oscillatory waves immunity Voltage fluctuation immunity Immunity to conducted common mode disturbance Ripple on DC input power port immunity Variation of AC power frequency immunity
IEC 61000-4-29
UL 60950-1 EN 60950-1 FCC 47 CFR 15 FCC 47 CFR 90 FCC 47 CFR 24 Industry Canada IEC 61000-6-3
Safety Safety Emissions Emissions Emissions (900 Band Only) Emissions Emissions
46
Altitude Derating
The MTR3000 meets full specified specifications from altitudes of -980 to 5900 feet (-300 to 1800 meters) referenced to mean sea level. With altitudes in the range of 5900 to 16400 feet (1801 to 5000 meters), the transmitter output power will automatically rollback as needed to keep the station within its thermal limits.
47
RFDS OPTIONS
The RFDS (radio frequency distribution system) provides interconnect between the base stations/repeaters and antennas. For the transmitters this includes isolator trays, duplexers, and antenna relays. For the receivers this includes preselectors, duplexers, and antenna relays. Various RFDS options exist for the MTR3000 Base Station/Repeater, which be outlined in the following pages.
48
Typical
Notes
Figure 10. UHF Duplexer Plots (T-band) TX=471 MHz, RX=474 MHz
sAT sRA
49
Loss (dB)
sAT sRA
469
470
471
472
473
474
475
476
477
478
479
480
Frequency (MHz)
Loss (dB)
sRA sAT
Duplexer Insertion Loss 0 20 40 60 80 100 120 440 445 450 455 460 465
Loss (dB)
Freq (MHz)
50
481
sRA sAT
Typical
Notes
51
52
X265 Base Station/Repeater Preselector (UHF) The Base Station/Repeater Preselector provides additional rejection of unwanted signals including the transmitter signals from overloading the receiver. The filter is optional for the MTR3000 Base Station/Repeater. The base station/repeater preselector is not required when using a receiver multicoupler system since the preselector in the multicoupler should provide sufficient rejection. This filter can be retuned in the field.
NOTE : The external preselector option is not offered in the 800/900MHz band.
Table 17. UHF Base UHF Base Station/Repeater Preselector Specifications Parameter
Tuning Range Bandwidth Insertion loss VSWR max. Input Connector Output Connector
Typical
Notes
1.3 dB 1.5:1
53
BR Preselector (Stopband)
0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 430 440 450 460 470 480 490 500 Frequency (MHz) 510
54
Loss (dB)
X676 (UHF)
For UHF, the units ship either as 403-470 or 470-512 MHz. The plots & specifications in the figures below include the loss of the low pass filter & cables for the 403-470 MHz version.
55
Limit
403-470 or 470-524 MHz 1.6 dB 18 dB 40 dB 200 W 55 dB RF Cable with N male N female
Typical
1.2 dB 24 dB 50 dB
Notes
Includes cable loss
56
X676 (800MHz)
The plots & specifications in the figures below include the loss of the low pass filter & cables.
Typical
1.2 dB 42 dB
Notes
Includes cable loss
57
58
59
MODULES
Power Supply Module
The MTR3000 Power Supply Module accepts an AC or a DC input and generates three output DC voltages to power the station modules. All three outputs provide over-voltage / over-current protection to their loads. The power supply is a high-frequency switched mode design with power factor correction, all contained in a metal heat-sink and mounted on the left-hand side of the station. The AC input connection is made at the rear of the station via an IEC-type connector keyed to accept only high temperature type mating connectors. Also provided is a DC input connection which can be used as the primary means to power the station or used for battery revert operation should the AC mains fail. Power supply cooling is provided by a thermostatically controlled external fan (a field replaceable part itself) which provides forced air across the power supply heat sink fins. Power Supply Connections There are two electrical connection assemblies on the PS: Power supply connection and AC fail indication to backplane (rear cable harness) Power supply connection to power amplifier (rear cable harness)
60
PS Containment The PS is secured to the station chassis with 6 TORX screws (T20 bit size required).
Performance Specifications
Table 19. Power Supply Performance Specifications (AC) AC Performance Specifications Parameter
Input Voltage Range Input Frequency Range Steady State Output Voltage Output Power (Rated) Output Ripple +28.6 VDC Output Ripple +14.2 VDC Output Ripple +5.1 VDC
Value or Range
85 VAC to 264 VAC 47Hz to 63 Hz 28.6V @ 13 A 14.2V @ 8 A 5.1V @ 2 A 500W 50 mV p-p, @ 25C (77F) 50 mV p-p, @ 25C (77F) 100 mV p-p, @ 25C (77F)
61
Table 20. Power Supply Performance Specifications (DC) DC Performance Specifications Parameter
Input Voltage Range Steady State Output Voltage Output Power (Rated) Output Ripple +28.6 VDC Output Ripple +14.2 VDC Output Ripple +5.1 VDC
Value or Range
21.6 VDC to 32 VDC 28.6V @ 13 A Input voltage dependent 14.2V @ 8 A, Regulated 5.1V @ 2 A, Regulated 500W Input voltage dependent (Argus) 50 mV p-p, @ 25C (77F) 100 mV p-p, @ 25C (77F)
Table 21. Power Supply Performance Specifications (Switching) Typical Switching Frequencies Parameter
Power Factor Correction Main Converter
Value or Range
82kHz 137kHz
62
The Power Amplifier (PA) is a forced convection-cooled continuous wave RF power amplifier. It accepts a low-level modulated RF signal from the Exciter Module, and amplifies the signal to the end users selected transmitter output power. The PA is designed for continuous-duty operation across the specified band for all power levels. All PA modules contain a multi-stage power amplifier board at the input (RF Board), a circulator with isolation load termination, a low-pass filter, and directional couplers at the output (Output Board), and a DC Distribution Board incorporating circuitry for diagnostics and RF power control. The PA provides alarms for VSWR, Low Output Power, High Temperature, Low/High DC voltage and Cooling Fan failures (cooling fan is field replaceable). In the event of these alarms, with their severity weighed, the PA in conjunction with the station firmware will take measures such as rolling the power back or de-keying the station to protect the hardware from damage or improper operation. The PA and its sub-circuits are broad-band devices and require no manual tuning or alignment to operate at the site as their calibration parameters are stored in the PAs EEPROM. As such, in the event the PA requires replacement, no calibration is needed after its replacement. Note: If the station is upgraded from MTR2000, refer to MTR2000 Basic Service Manual (included with the original MTR2000 station) for all PA information.
63
Power Amplifier Connections There are three electrical connection assemblies on the PA: Power supply (rear cable harness) Communications connector (rear ribbon cable). RF input connector (BNC female) RF output connector (N-Type female).
PA Containment The PA is secured to the station chassis with 6 TORX screws (T20 bit size required). PA Basic Electrical Performance
Table 22. Power Amplifier Performance Specification Parameter
Operational Frequency Range Minimum Input Return Loss (TX mode) Rated RF Output Power Range Rated RF Input Power Range 28 V Supply Nominal Voltage (AC Power) 14 V Supply Nominal Voltage 28V Supply Maximum Current Draw 14V Supply Maximum Current Draw Maximum Standby Power Consumption
Specification
403-470 MHz 7 dB 8 - 100 W 9.8 14 dBm 28.6 V (+/- 4%) 14.2 V (+/3.5%) 12.6 A 2.0 A 1.2 W 470-524 MHz 7 dB 8 - 100 W 9.8 14 dBm 28.6 V (+/- 4%) 14.2 V (+/3.5%) 12.6 A 2.0 A 1.2 W 800/900MHz 10 dB 8 - 100 W 12.8 18.5 dBm 28.6 V (+/- 4%) 14.2 V (+/3.5%) 12.6 A 2.0 A 1.5 W
Power Meter Accuracy The forward power meter is typically -/+10% at maximum rated output power. Keep in mind that the calibration point of the reading is the output connector of the PA. This is important to remember when duplexers, isolator trays, or antenna relays are installed.
64
Receiver Module
The receiver provides the hardware portion of the receiver functionality for the station. The receiver module performs selective band-pass filtering (varactor tuned) and dual downconversion of the desired RF signal. An application specific receiver IC then performs an analog-to-digital conversion of the desired received signal and outputs a differential data signal to the Station Control Module (SCM). The receiver has the capability through CPS (Customer Programming Software) to be programmed for an analog or digital mode. For analog mode, the receiver is programmed for 12.5 kHz and 25 kHz bandwidths, on a per channel basis. This allows a single station to be programmed to function in various bandwidths without changing hardware For UHF stations without the external preselector option, it is not recommended to allow a colocated transmitter frequency which is 36.675MHz above the receiver frequency. Receiver Connections There are two electrical connection assemblies on the receiver: Communications / Power / Digital signal (edge connector) RF input connector (BNC female)
65
Specification
403-470 MHz 450-524 MHz Full Bandwidth Full Bandwidth -118.8dBm (0.257uV) Receiver FRU w/o cable loss 85dB 75 dB at 12 kHz, 80 dB at 25 kHz 85dB 1st : 73.35 MHz 2nd : 2.25 MHz 0.04A from 14.2 VDC supply 0.52A from 10 VDC supply 0.11A from 8 VDC supply 50 806-825MHz & 896-902MHz Full Bandwidth 117.8dBm (0.288uV) Receiver FRU w/o cable loss 85dB 75 dB at 12 kHz, 85 dB at 25 kHz 90dB 1st : 73.35 MHz 2nd : 2.25 MHz 0.04A from 14.2 VDC supply 0.52A from 10 VDC supply 0.11A from 8 VDC supply 50
66
Exciter Module
The Exciter Module (in conjunction with the Power Amplifier Module) provides the transmitter functions for the station. Contained within a metal clamshell housing, the Exciter board generates a low-level modulated Radio Frequency (RF) signal that is delivered to the power amplifier module for further amplification and output to the transmit antenna. The Exciter Module interfaces directly with the Station Control Module (SCM), which provides control signals and monitoring, and routes transmit digitized audio to the Exciter. The RF carrier is generated by a frequency synthesizer consisting of synthesizer circuitry and Voltage-Controlled Oscillator (VCO) circuitry. Exciter module control signals, monitoring, and audio processing are handled by the Station Control Module (SCM). Exciter Connections There are two electrical connection assemblies on the receiver: Communications / Power / Digital signal (edge connector) RF output connector (BNC female)
67
Specification
403-470 MHz Full Bandwidth 450-524 MHz Full Bandwidth 851870 MHz and 935941 MHz Full Bandwidth (851870 MHz & 935941 MHz) 1318 dBm (800 MHz), 1418 dBm (900 MHz) 0.05 A from 14.2 VDC supply 0.15 A from 10 VDC supply 0.1 A from 8 VDC supply -20dBc 50
10 - 14dBm 0.04A from 14.2 VDC supply 0.15A from 10 VDC supply 0.02A from 8 VDC supply -20dBc 50
68
The Station Control Module (SCM) performs station management, digital signal processing, data formatting and audio routing for the base station/repeater. It provides interfaces to the Exciter, Receiver and PA as well as the interfaces to external site equipment. The controller uses two TI OMAP series processors: One for transmit and overall base station/repeater control functions and one for all receive functions. The audio interface provides flat and pre-emphasized transmit audio inputs as well as an independent data/PL/DPL input. Transmit and receive audio signals are accessible on the rear DB25 connector. A front panel microphone and speaker provide local audio (analog mode only). The 10/100BaseT Ethernet port is used to connect to station to a local or wide area network for IP Site Connect and remote diagnostics & control. The front cover must be removed to access this connector. Alternatively, a short extension cable can be used to route this connection to the rear of the station. A front accessible USB port provides the interface to the local service computer for radio configuration. The SCM provides the station frequency reference to the Exciter and Receiver module. A TCXO (Temperature Compensated Crystal Oscillator) provides the stability required for UHF and VHF bands and an OCXO (Oven Controlled Crystal Oscillator) provides the stability required for 800/900MHz bands. An external frequency reference can be connected to a BNC connector behind the front panel to calibrate the onboard TCXO/OCXO. The front cover must be removed to access this connector. If an external reference is to be used with the MTR3000, a short extension cable can be used to route this connection to the rear of the station. Alternately, the reference cable (and/or Ethernet cable) can be routed out the front of the station via the slots provided along the edge of the front bezel. 69
Connector Type
Purpose
Service Computer connection. This connector is accessible with front cover in place. VBUS (+5 volts) is not provided on the USB connector to prevent potential damage to the Service Computer. Microphone connection. Compatible with microphone GMMN4063 or equivalent (older model, GMN6147). This connector is accessible with front cover in place. Supported in analog mode only. Note: The MTR3000 does not support the 3 control buttons on the GMN6147 microphone for speaker volume, Rx monitor, and Intercom control functions. Speaker connection. Compatible with Service Speaker HSN1000 or HSN1006. This connector is accessible with front cover in place. Supported in analog mode only Provides for network connections (e.g. IP Site Connect). The front cover must be removed to access this connector. Alternatively, a short extension cable (straight or crossover) can be used to route this connection to the rear of the station. External reference input. The front cover must be removed to access this connector. Alternatively, a short extension cable can be used to route this input to the rear of the station.
USB Type B
Mic
RJ45 (8 pin)
Speaker Ethernet
Ext Ref
70
State
N/A Flashing Solid Flashing Solid Flashing Flashing Solid N/A Solid Flashing Flashing N/A Solid Flashing Flashing N/A Solid Flashing N/A Solid Flashing N/A Solid Flashing
Condition
Station Off Station Operating Normally, with DC power Station Operating Normally, with AC power Station Operational - Minor Alarm Station Not Operational and locked - Major Alarm Station in Service Mode Station in Boot Mode (all LEDs)
Station is Disabled (Dekeyed) Transmitter is not transmitting Transmitter is transmitting
Power/Status
Transmitter is transmitting, but at reduced power Station in Boot Mode (all LEDs)
Transmitter is not transmitting Transmitter is transmitting
Transmitter is transmitting, but at reduced power Station in Boot Mode (all LEDs)
Receiver qualifier has not been met Receiver qualifier has been met
Receive Slot 1
Mode
Color
Off Green Green Off Amber
State
N/A Solid Flash N/A Solid Solid
No Ethernet connection Linked
Condition
Network Traffic
No external reference is present Training process is completed, and the calibration data has been written to the EEPROM, or an external reference is present after training (which the base station/repeater has phase locked to). Locked to external reference, and training is in progress
71
Wireline Board
The Wireline Board is the interface between the MTR3000 base station/repeater and the customers phone lines. The Wireline Board supports Local PTT, Tone, and DC Remote Control modes, of which the later two allow for channel selection and PTT signaling from compatible consoles. The Wireline Board can be configured for either 2-wire or 4-wire operation as needed. The Wireline Board uses Digital Signal Processing (DSP) techniques to implement all required remote control functions, filtering algorithms, and audio adjustments. Audio enters and leaves the board as analog, but is converted to digital in the interim for processing.
72
The Wireline board allows for configurable impedance matching to the greater wireline network. Line impedance is generally standardized by country or region as shown in the table below. The line impedance setting is configured using the CPS software configuration tool. Table:. Selectable Wireline Impedances
Tone Remote Control A tone sequence must meet specific requirements for timing, amplitude, and frequency to be considered valid. The timing requirements for a tone sequence are defined in the tables below. All tone sequences must include a minimum of 120 mS of high level guard tone and 40 mS of function tone. i.e. A function tone is required (even on single frequency systems). Low Level Guard Tone (LLGT) is not required. This allows the console to change frequencies or manipulate alternate CPS defined GPIO functions without keying up the base station/repeater. When Low Level Guard Tone is present (at the end of a tone sequence), the base station/repeater will key up and remain transmitting for as long as LLGT is present. The following tables reflect the predefined tone plans the MTR3000 base station/repeater supports (+/- 10Hz):
Function Tone Definition Table (TRC15) Tone (Hz) Function 2050Hz Monitor 1950Hz Frequency 1 1850Hz Frequency 2 1750Hz Frequency 3 1650Hz Frequency 4 1550Hz Frequency 5 1450Hz Frequency 6 1350Hz Frequency 7 1250Hz Frequency 8 1150Hz Frequency 9 1050Hz Frequency 10 950Hz Frequency 11 850Hz Frequency 12 750Hz Frequency 13 650Hz Frequency 14 550Hz Frequency 15 Function Tone Definition Table (TR7) Tone (Hz) Function 2050Hz Monitor 1950Hz Frequency 1 1850Hz Frequency 2 1750Hz Frequency 3 1650Hz Frequency 4 1550Hz Frequency 5 1450Hz Frequency 6 1350Hz Frequency 7 1250Hz Not Used 1150Hz GPIO8 Assert (see note) 1050Hz GPIO8 De-assert (see note) 950Hz GPIO9 Assert (see note) 850Hz GPIO9 De-assert (see note) 750Hz Not supported in initail release 650Hz Not supported in initail release 550Hz Not Used
NOTE: GPIO 8 and 9 do not support the CPS assignable Disable and Tx Power Level functions. 73
DC Remote Control
The following table reflects the predefined DC signaling plan the MTR3000 base station/repeater supports:
Current Definition Table Current (mA) Function -2.5mA (+/- 20%) Monitor -5.5mA (+/- 20%) Frequency 3 -12mA (+/- 20%) Frequency 4 2.5mA (+/- 20%) Frequency 5 5.5mA (+/- 20%) Frequency 1 12.5mA (+/- 20%) Frequency 2
74
MTR3000 INSTALLATION
Rack and Cabinet Installation, Placement & Site Design
Site Design There are certain rules which must be followed when designing a site with base stations/repeaters which are forced convection cooled. Since base stations/repeaters with forced convection cooling (fans) are typically smaller than those without fans, the natural tendency of the site designer is install as many base stations/repeaters in an area as possible. When cooling base stations/repeaters, the environment in which the base stations/repeaters are installed is just as important as the actual heat sink designs for the electronics. Some planning must go into the ventilation, and in most cases, air conditioning of the sites. When an MTR3000 is placed in a cabinet, there must be vent openings on the sides for air to enter, and vents in the back for air to exit. To make sure the airflow through the cabinet is not restricted there must be a minimum of six inches of open area between the outlet of the air vent on the rear of the cabinet and any airflow obstructions. It is also desirable to avoid exhausting heat on cables to avoid shortening cable life span. Warning: It is strongly recommended to NOT install batteries in the cabinet with the station. Hydrogen and oxygen gases produced during electrolysis are colorless and odorless. The hydrogen gas is of particular concern since it produces a potentially explosive atmosphere when it reaches a 4% level of concentration in the air. The room containing the battery must have sufficient natural or forced air ventilation to prevent a build-up of gas exceeding 2% of the room's occupied volume. In addition, the gas must be vented to the outside rather than re-circulated. Therefore, installing a battery in the cabinet could cause serious venting problems.
A convenient location should be chosen with regard to power, control line, and antenna access. Refer to the Motorola R56 Standards (hardcopy p/n: 68P81089E50-B, CD-ROM p/n: 98R80384V83) for proper placement and installation of these lines. The base station/repeater should also be readily accessible for future maintenance and servicing. Providing adequate lightning protection is critical to a safe and reliable communications site. Telephone lines, RF transmission cables, and AC and DC power lines must all be protected to prevent lightning energy from entering the site building. RF transmission lines from the antenna, down the tower, and into the building must be grounded. All RF transmission lines, including unused spares, must contain a lighting surge suppresser. Further information can be found in the Motorola Quality Standards Fixed Network Equipment Installation manual, R56 (Part # 68-81089E50). Equipment shall be installed in site meeting the requirements of a restricted access location, per UL60950-1, which is defined as follows: Access can only be gained by service persons or by user who has been warned about the possible burn hazard on equipment metal housing and hazardous energy
75
level. Access to the equipment is through the use of a tool or lock and key, or other means of security, and is controlled by the authority responsible for the location. Installation Considerations Rear access is required for the MTR3000. No clearance is required on the sides of the cabinet or racks; however, there must be provisions for proper ventilation which allows for air intake by the PA and PS fans, which draw air in from the side. Service access for the MTR3000 Base Station/Repeater requires a minimum of two feet in front and rear of the rack or cabinet for servicing equipment. Seismic Reliability MTR3000 cabinets and open racks that are installed in seismically active areas may require additional anchoring and support. Refer to your local regulatory agency requirements regarding seismic considerations for your particular location. For installation guidelines, also refer to the Motorola Standards and Guidelines for Communications Sites (R56) document (Motorola Part Number 6881089E50). Cabinet Stacking Depending on the floor-to-ceiling height available, the MTR3000 cabinets and racks may be stacked. It is necessary to securely fasten the bottom cabinet or modular rack to the floor or other rigid surface capable of supporting the load of the stacked configuration. Order kit number TRN7750 for hardware between two cabinets or modular racks that are stacked. The maximum number of cabinets or modular racks that can be stacked is as follows: The 30 Modular Rack can be stacked a maximum of 3 per stack (2286 mm (90 in.)). The 45 Modular Rack can be stacked a maximum of 3 per stack (2286 mm (90 in.)). The 52 Modular Rack can be stacked a maximum of 2 per stack (2640 mm (104 in.)). The 30 Cabinet can be stacked a maximum of 3 per stack (2286 mm (90 in.)). The 46 Cabinet can be stacked a maximum of 2 per stack (2337 mm (92 in.)). The 60 Cabinets cannot be stacked. Cabinet Mount The mounting of only ONE STATION PER CABINET is recommended. More than one station per cabinet will result in degradation of thermal specifications at high ambient temperatures. Appropriate precautions should be taken to ensure that the station ambient temperature does not exceed +60 C (+140 F). These guidelines apply to closed cabinets. For open cabinets (i.e., no doors or side panels), refer to rack mount guidelines below for thermal impact. 76
Rack Mount Multiple MTR3000 stations can be mounted in an open rack without degradation of specification. To maintain thermal specifications for equipment including the DLN6718 (Station Control OCXO), MTR3000 stations require 1 Rack Unit of spacing between stations. For stations with DLN6718 that are installed with no spacing, the station ambient temperature may not exceed +50 C (+122 F). NOTE: The DLN6718 is standard/required in the 800/900MHz bands (T3000A and T2003A)
The peripherals that are used for the MTR2000 can remain in use for the MTR3000. There is no need to change out any of the following peripherals if a MTR2000 is upgraded or an MTR3000 is used in place of an MTR2000: Duplexer Preselector Dual circulator External frequency reference (EFR) Antenna relay Argus Battery Charger (L1884A)
The following connectors have changed between that of an MTR2000 and an Upgraded MTR2000 / MTR3000. They are as follows: Service port -- It is now a type B female USB Wireline Connector (Backplane J6) -- It is now a detachable screw terminal block.
Note: This connection is not functionally supported in the initial release of the MTR3000.
77
Analog Radio Interface The analog radio interface at the System (J5) and Aux (J7) backplane connections has extensively changed between that of an MTR2000 and an Upgraded MTR2000 / MTR3000. All existing cables that connected to a MTR2000 stations J5 and J7 connector can not be used with an Upgraded MTR2000 / MTR3000. In general, all analog radio interfaces will be made at the J7 connector on the MTR3000. Details of the signals are provided in the Backplane Connections section of this manual. The 3rd party controller cables that will connect to the MTR3000 J7 connector can be fabricated by the aid of the wiring diagrams provided in the Basic Service Manual (Appendix D). Alternately, the cables for the following 3rd party controllers can also be obtained directly from the noted manufactures. Model 30 World Patch (Motorola, X244AH) Model 38 Community Repeater Panel (Motorola, X244AJ)
NOTE: The MTR3000 base station/repeater doesnt require the use of the Wireline Board to support the above mentioned 3rd party controllers. This is being noted since the MTR2000 did require the use of its Wireline Board to support said 3rd party controllers. Wireline Interface The Wireline interface to the MTR3000 base station/repeater is provided by a the MTR3000 Wireline Board. Although the Wireline is installed as a card inside the MTR 3000 Base Station/Repeater, its operation is similar to an External Tone Remote or a DC Remote Adapter. The Wireline Board drives the same GPIO signals that an external controller would drive if it were connected to the J7 DB-25 connector on the back of the base station/repeater. Although the Wireline Boards functionality is similar with an external controller solution, almost all Wireline options are configured through the CPS and Tuner software configuration tools, just as the other base station/repeater options are. The salient differences between the MTR3000 and MTR2000 Wireline functions are as follows: The MTR3000 Wireline supports (and the MTR2000 does not) the following: - DC remote - 2-Wire, 4-Wire, and multi-national impedance support with one FRU - CPS configurable impedances - FCC part 68 compliance - Preconfigured tone tables The MTR2000 Wireline supports (and the MTR3000 does not) the following: - Dynamic tone tables - Multiple commands per tone - 8-Wire
NOTE: The MTR3000 Wireline Board will not function in the MTR2000 base station/repeater 78
GPIO and Audio Configuration The configuration of the MTR3000 GPIO and audio types for the various controllers noted in the Analog Radio Interface and Wireline Interface sections can be accomplished with the CPS application. Details of the specific configuration settings are noted in Appendix G of the Basic Service Manual. Incompatible MTR2000 FRUs and Boards The MTR2000 wireline boards are not compatible with an upgraded MTR2000 / MTR3000 station. After a MTR2000 has been upgraded, its existing wireline board (if present) should be removed. Additionally, the Aux I/O board from the MTR2000 will not be supported in the initially releases for the upgraded MTR2000 / MTR3000. However, the COR and PTT functions (TIA986 E&M compliant) are planned to be supported in future releases via the MTR2000 Aux I/0 board. The Main / Standby feature was often employed in the MTR2000 station, which required the Wild Card Option as well as the Aux I/O card itself. The upgraded MTR2000 / MTR3000 will support a version of the Main / Standby function as a standard feature. The configuration parameters to invoke this functionality are noted in the MOTOTRBO System Planner. Note: With the Upgraded MTR2000 / MTR3000, once the standby station is the active repeater, the main repeater will be locked out of service even if its fault recovers. To unlock an Upgraded MTR2000 / MTR3000 station requires a local read / write of the station codeplug after the fault condition is corrected. Lastly, MTR2000 receivers, exciters, and control FRUs can not be used in conjunction with any MTR3000 receiver, exciter, or control FRU. MTR3000 and Upgraded MTR2000 Analog Radio Interface Differences Via the components of a MTR2000 MOTOTRBO Digital Upgrade (T2003A), an upgraded MTR2000, will provide identical functionality to that of a MTR3000 with the exceptions of the following: The PA sticker code calibration coefficients must be entered into the codeplug for an Upgrade MTR2000 since the original MTR2000 PA does not have an onboard EEPROM for their storage. The Upgraded MTR2000 J7 backplane connector does not provide the accessory 14.2VDC (pin 20) or GPIO_10 (pin 5) functionality. For the Upgraded MTR2000, these signals must be accessed at the J5 System connector. The Upgraded MTR2000 will not support the MTR3000 wireline card, which provides integrated tone and DC remote control. NOTE: In regards to the 2nd and 3rd bullets above, an Upgraded MTR2000 can support said J7 backplane connections as well as the MTR3000 Wireline Board if the MTR2000 backplane is replaced/upgraded. The part number of the replacement/upgraded backplane is DLN6721. 79
MTR3000 and Upgraded MTR2000 Analog Radio RF Performance Differences An Upgraded MTR2000 and MTR3000 will provide the same RF receiver and transmitter performance with the exception that the MTR3000 will allow an extended RF power out range for the high power models. The power output range of an MTR3000 is 8W-100W (UHF and 800/900), while an Upgraded MTR2000 or MTR2000 has a power output range of 25W-100W (UHF) and 20W-75W (800 or 900). Station Grounding The MTR3000 Base Station/Repeater is designed to accept a grounding cable adjacent to the receiver antenna connection at the rear of the station. An M8 tapped hole in the Power Supply module is equipped with a M8 machine screw with external tooth star washer. The grounding cable lug should be securely fastened to this point, which is marked with the international ground symbol. Refer to the Motorola R56 Standards (hardcopy p/n: 68P81089E50-B, CD-ROM p/n: 98R80384V83) for grounding cable specifications and routing guidelines.
Backplane Connections
MTR3000 Base Station/Repeater Backplane Connections
80
Description
System (User Interface) Wireline (User Interface) Aux System (User Interface) Power Amplifier Control Power Supply Antenna Relay and Peripheral Temperature
Connector Type
96 Pin Euro 4 Conductor Terminal Block DB25 10 Pin 8 Pin 3 Pin
The J7 Aux connection on the MTR3000 and Upgraded MTR2000 is the main analog radio interface to the station. Table 29 shows the signal names and functions as well as a cross reference to the MTR2000 signaling names. Note that Pins 3, 5, 6 and 20 are not supported in the Upgraded MTR2000 since the upgraded station is still using the MTR2000 backplane.
81
The J5 connection on the MTR3000 and Upgraded MTR2000 supports a reduced function set relative to the MTR2000 J5 connection. Table 30 shows the supported functionality for the Upgraded MT2000 and MTR3000 J5 backplane connection.
Table 30. MTR3000 J5 System Backplane Connections
82
POWER SOURCE
Block Diagram of AC & DC Flow
The MTR3000 Base Station/Repeater can operate from either AC or DC power as its primary power source. The MTR3000 Base Station/Repeater can also provides battery revert functionality when both an AC and DC source is interfaced to the Base Station/Repeater. When both AC and DC sources are supplied, the station will operate from the AC power source unless the AC power source is interrupted, at which time the station will automatically revert to the DC power source. Operation returns to the AC source when the AC source is restored. Switchover from AC to DC and back again is fully automatic. No operator action is required. Figure 50 shows the AC and DC power distribution in the MTR3000 Base Station/Repeater when an AC with battery revert system is employed. Note: When both AC and DC sources are present at the station power supply, AC will always take precedence.
83
Power Rollback
It is important to note that when the Upgraded MTR2000 or MTR3000 is running from a DC source, the maximum RF output power is dependent on the station power supplys DC input voltage. Figure 24 shows a graphical representation of what the maximum RF output power is as a function of the DC input voltage of a UHF station and figure 25 shows the maximum RF output power as a function of the DC input voltage of a 800/900MHz station. From Figure 24 and 25, the following can be seen: The stations max output power is equal to 0W when; 21.6VDC > DC input voltage > 32VDC The stations max output power is equal to 65W when; 30.7VDC < DC input voltage 32VDC For UHF, the stations max output power is equal to 100W when; 25.7VDC DC input voltage 30.7VDC For 800/900MHZ, the stations max output power is equal to 100W when; 24.7VDC DC input voltage 30.7VDC The stations max output power is equal to (DC input voltage 21.6) * 10 + 60; when 21.6VDC DC input voltage < 25.7VDC
Note: 21.6VDC and 32VDC are the specified operating limits of the station. Beyond those limits, the power supply of the station will power itself (and the Base Station/Repeater) down for its own protection as well as the batteries.
Figure 24. UHF RF Power Out Rollback Curve
0W 21.6V
25.7V DC Input
30.7V
32V
84
85
L1884 Battery Reverting 24V DC charger requires, in addition, the following cables: o CDN6226A CHGR LOAD CABLE MTR2000 ( to connect the Battery charger with the MTR3000 Base Station Power Supply) o CDN6227A CHGR BAT CABLE MTR2000 (to connect the Battery charger to the battery)
Consult the Battery Reverting Charger Detailed Technical Specifications for information regarding charger specifications, battery selection, wiring gauge determinations, and precautions.
AC Breaker Recommendation
Each MTR3000 should have its own AC supply breaker in order to ensure that a fault which causes the breaker to open does not result in the loss of multiple transmit channels. However, multiple MTR3000 stations could be supported on a single circuit (see Power and Energy Consumption Curves section).
86
For a 120 VAC, 60Hz application, the AC supply breaker should be rated for a continuous current of no less than 15A, with a recommended rating of 20A. For a 220 VAC, 50Hz application, the AC supply breaker should be rated for a continuous current of no less than 15A, with a recommended rating of 20A. The above breaker current ratings are per R56 guide lines for communications equipment.
DC Breaker Recommendation
For information involving the sizing of cables and DC power distribution, please refer to the Motorola R56 standard Standards and Guidelines for Communication Sites (68P81089E50). For each MTR3000 Base Station/Repeater, the DC supply breaker should be rated for a continuous current of 20A.
87
Alignment
The MTR3000 requires the alignment of up to three parameters. They are as follows: Modulation Limit: The alignment is only needed in cases where the station is interfaced to a 3rd party controller that requires the use of the TX Data port on the J7 backplane connection. Power Output Calibration (Upgraded MTR2000 Only): This alignment is to allow entry of the PA sticker code calibration coefficients into the stations codeplug. Speaker Volume: This alignment is for the adjustment of the speaker port audio output level. (analog mode only) Station Frequency Reference: Recommend to be verified / aligned once per year to maintain regulatory compliance.
88
The CPS install disk contains three CPS applications; CPS, Repeater Diagnostics and Control (RDAC), and Tuner. Each of the three applications contains on line help to aid the user in configuring and aligning the station. In general, the purpose of the three applications is as follows: CPS: Is radio programming software for dealers and service technicians who need to configure the MTR3000. The CPS allows the user to access and program (e.g. read, write or clone) the codeplug of the MTR3000 in the available systems. Tuner: Is an application that allows for the alignment of the MTR3000 (Modulation Limit, Speaker Volume, and MTR2000 Upgrade PA sticker code entry). It also allows testing of the MTR3000 (Bit Error Rate). RDAC: Is an application for the system technicians who need to run diagnostics on the MTR3000. It allows the user to remotely or locally monitor the status of the radio and gather real-time radio hardware failure reports via alarm messages reported by the radio. In addition to the diagnostics capability, the application also allows the user to remotely control some of the parameters of a radio. The application can be used in a Single-Site (Local mode) or IP Site (IP Site mode) environment with the main purpose of maintaining all the radios registered within the system.
The MTR3000 and the MTR2000 MOTOTRBO Upgrade both use model GMVN5141 CPS. This is the same CPS that is used to program the MOTOTRBO mobiles, portables and DR3000 station. The software is developed to recognize the station it is programming; therefore you may see different options in the MTR3000 programming software that you have not seen in the DR3000. MTR3000 stations use a standard type A to type B USB cable for connection to the CPS computer. The cables used to program each MOTOTRBO product may be different. Refer to the MTR3000 and the DR3000 ordering guide and price pages to determine the cable that is required.
The Customer Programming Software (CPS) periodically has new releases available. The most current software release is located on Motorola on line (MOL).
90
Order Main Model T3000A MTR3000 Base Station/Repeater Required: Select 1 Frequency X340MT ADD : UHF 100W POWER (403-470) X540MT ADD : UHF 100W POWER (470-524) Optional: Software Feature HKVN4045A MTR3000 CAPACITY PLUS SW UPGRADE Optional: Select Duplexer X182UL ADD : DUPLEXER, UHF 403-435 MHz X182UM ADD : DUPLEXER, UHF 435-470 MHz X182UN ADD : DUPLEXER, UHF 470-494 MHz X182UH ADD : DUPLEXER, UHF 494-512 MHz Optional: Select Preselector (Required if ordering X182, Duplexer) X265UL ADD: PRESELECTOR, UHF(380435 MHZ) X265UM ADD: PRESELECTOR, UHF(435470 MHZ) X265UH ADD: PRESELECTOR, UHF(470524 MHZ) Optional: Select Circulator X676UL ADD: CIRCULATOR, UHF (403470 MHZ) X676UH ADD: CIRCULATOR, UHF (470524 MHZ)
91
Optional Select Antenna Relay (Not compatible if ordering X182, Duplexer) X371BA ADD: ANTENNA RELAY Optional: Select Power Cable (North America Cable ships standard) X187AK ADD : POWER CABLE, EUROPE X162AE ADD : POWER CABLE, UK X191AF ADD : POWER CABLE, AUSTRALIA CA01520AA ADD : POWER CABLE, DC Optional: Mounting Hardware U178AB ADD: CABINET MOUNT HARDWARE X153BA ADD: RACK MOUNT HARDWARE Optional: Manual on CD X347AF ADD: MANUAL INSTALL & USER CD Optional: Select System Cables X244AJ ADD: AUXILIARY SYSTEM CABLE X244AG ADD: COMMUNITY REPEATER PANEL CABLE X244AH ADD: PHONE PATCH CABLE C540AD ADD: SYSTEM CONNECTOR CABLE XA00032AA ADD: ETHERNET CABLE 12' Optional: Select Test Report X699BA ADD: MTR3000 FACTORY TEST REPORT Optional: Add FRU's as Necessary DLN6701A FRU UHF 100W PA 403-470 DLN6702A FRU UHF 100W PA 470-524 DLN6703A FRU UHF 403-470 EXCITER DLN6704A FRU UHF 450-524 EXCITER DLN6705A FRU UHF 403-470 RECEIVER DLN6706A FRU UHF 450-524 RECEIVER Optional: Add FRU's as Necessary DLN6707A FRU MTR3000 AC/DC POWER SUPPLY DLN6719A FRU STATION CONTROL TCXO THN6700A 12" INDOOR CABINET THN6701A 30" INDOOR CABINET THN6702A 46" INDOOR CABINET 0782099W01 30" MODULAR RACK (16 RK U) 0782099W02 45" MODULAR RK (24 RK U) 0782099W03 52" MODULAR RK (27 RK U) CLN6679A RACK MOUNT HARDWARE
92
T3000A is the MTR3000 Base Station/Repeater Model. This model number is always the first item entered on an order. It is only possible to order quantity one T3000A per line item. A TX/RX frequency must be specified for EACH MTR3000 Base Station/Repeater. The frequencies will be collected at the main model level. This model number will generate internally added options for all hardware components that are not generated by an orderable option. The Base Station/Repeater will not ship in a cabinet or rack. Cabinets and racks are available through the Aftermarket & Accessories division @ 800-422-4210. Frequency Band and Power Level ADD : UHF 100W POWER (403-470) (X340MT) ADD : UHF 100W POWER (470-524) (X540MT)
One TX and one RX frequency must be specified and will be collected at the main model level. For 800/900 MHz and UHF, all frequencies must be divisible by 6.25 kHz. For VHF, all frequencies must be divisible by 6.25 kHz or 5 kHz. Please note that there must be 5 digits after the decimal point when requesting frequencies. Frequency Rules for X340MT (UHF R1) RX Range: TX Range: 03.00000 470.00000 MHz. 03.00000 470.00000 MHz.
If Freq (TX) is 403-470 MHz, then Freq (RX) > + .25 MHz TX Frequency Rules for X540MT (UHF R2) RX Range: TX Range: 70.00000 524.00000 MHz. 70.00000 524.00000 MHz.
If Freq (TX) is 470-524 MHz, then Freq (RX) > + .25 MHz TX
Station or Repeater mode. The latest version of software is included in the purchase price of the MTR3000. To receive the latest software version refer to the following path: MOL > Resource Center > Software > Two-Way> MOTOTRBO > Firmware/Flashing Software Features and Repeater Software Upgrades. Customer Programming Software (CPS) GMVN5141 CPS Customer Programming Software
Customer Programming Software (CPS) is required to program the MTR3000. Order GMVN5141 Portable, Mobile and Repeater Customer Programming Software (CPS) Package: Package includes CPS, Air Tracer, Tuner, Repeater Diagnostics and Control (RDAC), MOTOTRBO System Planner, and 3 year subscription. Software is compatible with Windows XP (Home and Professional Versions) Windows 2000 and Vista. The GMVN5141 software updates are posted on MOL CPS Programming Cable (Part #: DDN9957): MTR3000 stations use a standard type A to type B USB cable for connection to the CPS computer. Notes: Configure the MTR3000 to either base station or repeater operation through the CPS. All Base Stations/Repeaters ship un-configured and must be field programmed via the CPS. MTR3000 cannot utilize the MTR2000 RSS (RVN4148). The GMVN5141 programs all MOTOTRBO products; MTR3000, DR3000 and MOTOTRBO mobiles and portable subscribers. MTR3000 stations use a standard type A to type B connection USB for CPS programming. Software Features Software features are optional. As new software releases are available there may be software features offered for an additional charge for each Base Station/Repeater license. Order HKVN4045A to add Capacity Plus to each base station/repeater. Capacity Plus is a cost effective single site Trunking solution. Capacity plus does not require an additional controller; it is a software based solution. When ordering the HKVN4045A an email address must be provided as the software entitlement id will be emailed to the requestor. The entitlement id allows a user to download the software feature at their convenience when they are connected to the MTR3000. To download the software version the computer that is connected to the station (via USB) must have an internet connection. HKVN4045A Capacity Plus SW License Key
94
Peripheral Options
Duplexer The Duplexer allows a single pair of transmit and receive channels to share a common antenna. The duplexer requires 3 rack units of space and will always require a cabinet or rack to be ordered (through the Parts department). The duplexer is factory tuned for single frequency operation only. It is not available for cross-band operation. UHF (403-524 MHz): The following peripherals are optional.
403-435 = 5MHz min/32MHz max (100dB isolation) 435-470 = 5MHz min/35MHz max (100dB isolation) 470-494 = 3MHz min/24MHz max (100dB isolation) 494-512 = 3MHz min/18MHz max (100dB isolation) ADD: DUPLEXER, UHF 403-435 MHz (X182UL) ADD: DUPLEXER, UHF 435-470 MHz (X182UM) ADD: DUPLEXER, UHF 470-494 MHz (X182UN) ADD: DUPLEXER, UHF 494-512 MHz (X182UH)
X182UL provides the option of using the same antenna for receive and transmit in the UHF (403-435 MHz) base station/repeater. If the X182UL is ordered, X265UL (ADD: NARROW PRESELECTOR, 380-435 MHz) is required. The TX and RX frequency separation must be at least 5 MHz. X182UM provides the option of using the same antenna for receive and transmit in the UHF (435-470 MHz) base station/repeater. If the X182UM is ordered, X265UM (ADD: NARROW PRESELECTOR, 435-470 MHz) is required. The TX and RX frequency separation must be at least 5 MHz. X182UN provides the option of using the same antenna for receive and transmit in the UHF (470-494 MHz) base station/repeater. If the X182UN is ordered, X265UH (ADD: NARROW PRESELECTOR, 470-524 MHz) is required. The TX and RX frequency separation must be at least 3 MHz. X182UH provides the option of using the same antenna for receive and transmit in the UHF (494-512 MHz) base station/repeater. If the X182UL is ordered, X265UH (ADD: NARROW PRESELECTOR, 470-524 MHz) is required. The TX and RX frequency separation must be at least 3 MHz.
Narrow Preselector The Base Station/Repeater Preselector rejects unwanted signals including the transmitter signals from overloading the receiver. The filter is optional for the MTR3000 Base Station/Repeater. This filter must be included to fulfill TIA102-CAAB Class A spurious response rejection (90 dB). The filter is usually not required when using a receiver multicoupler system since the Preselector in the multicoupler should provide sufficient rejection. 95
If a narrow Preselector is required, order X265UL, X265UM, X265UH, X265VL, or X265VH based on the frequency band of the system. The Base Station/Repeater Preselector rejects unwanted signals
including the transmitter signals from overloading the receiver. The filter is optional for the MTR3000 Base Station/Repeater. A narrow Preselector is required if a duplexer option is ordered for
VHF or UHF systems. No Preselector is needed for 800/900 MHz.
Note: The Preselector is recommended for dense RF site applications, especially when station is to be located with other stations in the same frequency band. The Preselector may not be required when the station is used with a multicoupler at an RF site. For multiple channel operation, the receiver frequency separation cannot be greater than 4.0 MHz. ADD: PRESELECTOR, UHF (380 435 MHZ) X265UL ADD: PRESELECTOR, UHF (435 470 MHZ) X265UM ADD: PRESELECTOR, UHF (470 524 MHZ) X265UH
X265UL provides RX filtering in the UHF sub-band 380 - 435 MHz for the base station/repeater and is attached to the back side of the base station/repeater. When ordering this option, the frequency separation between the highest RX frequency and the lowest RX frequency can be no more than 4 MHz. Also, all RX frequencies must fall within the following sub-band: 380 - 435 MHz. X265UM provides RX filtering in the UHF sub-band 435 - 470 MHz for the base station/repeater and is attached to the back side of the base station/repeater. When ordering this option, the frequency separation between the highest RX frequency and the lowest RX frequency can be no more than 4 MHz. Also, all RX frequencies must fall within the following sub-band: 435 - 470 MHz. X265UH provides RX filtering in the UHF sub-band 470 - 524 MHz for the base station/repeater and is attached to the back side of the base station/repeater. When ordering this option, the frequency separation between the highest RX frequency and the lowest RX frequency can be no more than 4 MHz. Also, all RX frequencies must fall within the following sub-band: 470 - 524 MHz.
Dual Circulator
If an external dual circulator is needed, order quantity one of X676UL, X676UH based on the frequency of the system.
ADD: CIRCULATOR, UHF (403-470 MHZ) (X676UL) ADD: CIRCULATOR, UHF (470-524 MHZ) (X676UH)
X676UL adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the UHF band (403 470 MHz). Since the power amplifier has one circulator, this option brings the total number of circulators to three. X676UH adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the UHF band (470 524 MHz). Since the power amplifier has one circulator, this option brings the total number of circulators to three.
96
Antenna Relay
X371BA provides the option of using the same antenna for receive and transmit, in base station operation only. The X371 will operate at any frequency transmit and receive frequency in the 136 MHz to 940 MHz range. If a X371 is required, then the difference between the RX and TX frequencies must be > than 100 kHz
DC Power Cables The MTR3000 Base Station/Repeater ships with the cabling required for powering the station with an AC current. If a DC power cable is required, please order the following option: ADD: POWER CABLE, DC (CA01520AA)
Battery Charging
For Battery Charging see ECAT/MOL price pages for Battery Reverting Charger. (Battery Reverting Charger Planner, R16-9-2)
International Power Cables A 12 foot AC power cable will come standard with the base station/repeater. If a different power cable is required, please order one of the following power cables and it will be shipped instead of the domestic power cable. ADD: POWER CABLE, EUROPE (X189AE) ADD: POWER CABLE, UK (X162AD) ADD: POWER CABLE, AUSTRALIA (X191AD)
Mounting Hardware Choose the Rack or Cabinet Mounting Hardware, if required. ADD: RACK MOUNT HARDWARE (X153AW) ADD: CABINET SLIDES HARDWARE (U178AB)
97
X153AW provides rack mount hardware for the base station/repeater as well as any associated optional/peripheral equipment. It should be selected if the base station/repeater will be installed in standard 19-inch relay racks. This option does not include rack. Use this option when a MTR3000 station to be installed in an existing customer supplied rack. The U178AB cabinet slides hardware option provides L-brackets which support the weight of the base station/repeater prior to the insertion of the front mounting screws. This option is designed for use with Schroff Eurorack cabinets and is not compatible with cabinet models THN6700, THN6701, or THN6702. Communication / Reference Cables Add cables as necessary for your specific customer configuration. ADD: COMMUNITY REPEATER PANEL CABLE (X244AJ) ADD: PHONE PATCH CABLE (X244AH) ADD: AUXILIARY SYSTEM CABLE (X244AF) ADD: SYSTEM CONNECTOR CABLE (C540AD) ADD: ETHERNET CABLE 12' (XA00032AA)
X244AJ Auxiliary System Cable provides a 25 foot male DB25 to open wire cable. This cable is used to access the RX audio, TX audio, 14VDC power, and GPIO control connections to and from the rear of the base station/repeater for use with external 3rd party boxes. C540AD System Connector Cable provides a 10 foot male 96 pin Euro connection to open wire cable. This cable is used to access the COR and opto-isolated PTT connections to and from the rear of the base station/repeater for use with external 3rd party boxes. X244AG Community Repeater Panel Cable allows connectivity from the MTR3000 to the Zetron (Model 38-Max) Community Repeater Panel. X244AF Phone Patch allows connectivity from the MTR3000 to the Zetron phone patch (Model 30). XA00032AA Ethernet port cables are 12 feet long. This allows for IP connectivity in the station.
C540AD Adds the cable kit needed to interface to the system connector on the backplane of the station. Includes housing shell and 30 pieces of 2-meter long, 24 gauge wire with a pin for header on one end and unterminated at the other end.
98
Racks and Cabinets The MTR3000 ships standard in a box without a rack or cabinet. Racks and Cabinets are optional and are available through Aftermarket Support (1-800-422-4210). 30" INDOOR CABINET (THN6701) 46" INDOOR CABINET (THN6702) 30" MODULAR RACK (16 RK U) (0782099W01) 45" MODULAR RACK (24 RK U) (0782099W02) 52" MODULAR RACK (27 RK U) (0782099W03) RACK MOUNT HARDWARE (CLN6679A)
30" Indoor Cabinet (THN6701) The cabinet is constructed of steel finished with exterior grade vinyl. Dimensions of the cabinet are 30" H X 22" W X 20" D (762 x 559 x 508 mm). Provides standard 19" EIA rack mounting inside the cabinet. The cabinet has holes in the bottom for easy stacking. There are also two 3 5/8" diameter knockouts near the rear of the cabinet in the top and bottom for routing cable between and out of the cabinets. 46" Indoor Cabinet (THN6702) The cabinet is constructed of steel finished with exterior grade vinyl. Dimensions of the cabinet are 46" H X 22" W X 20" D (1165 x 559 x 508 mm). Provides standard 19" EIA rack mounting inside the cabinet. The cabinet has holes in the bottom for easy stacking. There are also two 3 5/8" diameter knockouts near the rear of the cabinet in the top and bottom for routing cable between and out of the cabinets 30" Modular Rack (0782099W01) The modular rack is constructed of 10 gauge cold rolled steel, with a black baked enamel finish. Dimensions of the footprint are 22" W X 20" D (559 x 508 mm). Provides standard 19" EIA rack mounting. The base and cap have holes for stacking and routing cable between and out of the modular racks. This rack has 16 rack units available. Refer to Detailed Rack Specifications below for a figure with additional dimensional details. 45" Modular Rack (0782099W02) The modular rack is constructed of 10 gauge cold rolled steel, with a black baked enamel finish. Dimensions of the footprint are 22" W X 20" D (559 x 508 mm). Provides standard 19" EIA rack mounting. The base and cap have holes for stacking and routing cable between and out of the modular racks. This rack has 24 rack units available. Refer to Detailed Rack Specifications below for a figure with additional dimensional details. 52" Modular Rack (0782099W03) The modular rack is constructed of 10 gauge cold rolled steel, with a black baked enamel finish. Dimensions of the footprint are 22" W X 20" D (559 x 508 mm). Provides standard 19" EIA rack mounting. The base and cap have holes for stacking and routing cable 99
between and out of the modular racks. This rack has 27 rack units available. Refer to Detailed Rack Specifications below for a figure with additional dimensional details.
100
Description
MTR2000 MOTOTRBO Upgrade ADD : UHF 100W POWER (403-470) MTR3000 CAPACITY PLUS SW UPGRADE ADD: MANUAL INSTALL & USER CD ADD: ETHERNET CABLE 12' FRU UHF 100W PA 403-470 FRU UHF 100W PA 470-524 FRU UHF 403-470 EXCITER FRU UHF 450-524 EXCITER FRU UHF 403-470 RECEIVER FRU UHF 450-524 RECEIVER FRU MTR3000 AC/DC POWER SUPPLY FRU STATION CONTROL TCXO 12" INDOOR CABINET 30" INDOOR CABINET 46" INDOOR CABINET 30" MODULAR RACK (16 RK U) 45" MODULAR RK (24 RK U) 52" MODULAR RK (27 RK U) RACK MOUNT HARDWARE MTR3000 INSTALLATION AND USER MANUAL CD
101
Order a quantity of one T2003A per line item. Each upgrade contains a separate Exciter, Receiver, Control Module and front panel. For specific instructions on the upgrade process, refer to the MTR3000 Service and Installation Manual option X347AF. Notes: MTR2000 low power stations are not upgradeable at this time.. MTR2000 Receivers cannot be upgraded.
One TX and one RX frequency must be specified and are collected at the main model level. For UHF, all frequencies must be divisible by 6.25 kHz. Please note that there must be five digits after the decimal point when requesting frequencies. Frequency Rules for X340MT (UHF R1)
RX Range: TX Range:
If Freq (TX) is 403-470 MHz, then Freq (RX) > + .25 MHz TX
102
Customer Programming Software (CPS) is required to program the MTR3000. Order GMVN5141 Portable, Mobile and Repeater Customer Programming Software (CPS) Package: Package includes CPS, Air Tracer, Tuner, Repeater Diagnostics and Control (RDAC), MOTOTRBO System Planner, and 3 year subscription. Software is compatible with Windows XP (Home and Professional Versions) Windows 2000 and Vista. The GMVN5141 software updates are posted on MOL. Notes: Configure the MTR3000 to either base station or repeater operation through the CPS. All Base Stations/Repeaters ship un-configured and must be field programmed via the CPS. MTR3000 cannot utilize the MTR2000 RSS (RVN4148). The GMVN5141 programs all MOTOTRBO products; MTR3000, DR3000 and MOTOTRBO mobiles and portable subscribers. MTR3000 stations use a standard type A to type B connection USB for CPS programming. Software Features Software features are optional. As new software releases are available there may be software features offered for an additional charge for each Base Station/Repeater license. Order HKVN4045A to add Capacity Plus to each base station/repeater. Capacity Plus is a cost effective single site Trunking solution. Capacity plus does not require an additional controller; it is a software based solution. When ordering the HKVN4045A an email address must be provided as the software entitlement id will be emailed to the requestor. The entitlement id allows a user to download the software feature at their convenience when they are connected to the MTR3000. To download the software version the computer that is connected to the station (via USB) must have an internet connection. HKVN4045A Capacity Plus SW License Key
Communication Cable
XA00032AA ETHERNET CABLE 12'
XA00032AA Ethernet port cables are 12 feet long. This allows for IP connectivity in the station.
103
Manuals
If a manual is desired order one manual on CD per upgrade. Each CD contains the following: X347AF MTR3000 Installation and User Manual (Including MTR2000 to MTR3000 TRBO Upgrade) MTR3000 Basic Service Manual ADD : Manual Install and User CD
Note: The T3000A and the T2003A and associated options are RoHS (Restriction of Hazardous Substances) compliant.
Note: Existing peripherals that are being utilized for the MTR2000 can retrofit the MTR3000 once it is upgraded. There is no need to purchase a new Duplexer, Preselector or Circulator or Antenna Relay.
104
Ordering tips
Model Numbers are intuitive; MTR3000 Station = T3000 & MTR2000 MOTOTRBO Upgrade = T2003 Customer Programming Software (CPS) Model GMVN5141 is required to Program both the T3000 and the T2003 GMVN5141 is the same CPS used to program MOTOTRBO mobiles, portables & station A standard type A to type B USB cable is needed to program the MTR3000 Cabinets and Racks are no longer ordered as options, contact the Parts Department if cabinet and racks are needed. If customers are using specific features in MTR2000 be sure that their configuration is available prior to ordering the MTR3000 upgrade There are no orderable peripheral options available for the MTR2000 MOTOTRBO Upgrade, customers will need to order FRUs if peripherals are desired If a duplexer (X182) is added as a option to the T3000 the Preselector option (X265) is required. Only one freq UHF option (X340) applies for MTR2000 UHF Upgrades since MTR2000 did not extend beyond 470 MHz Capacity Plus is available for both the T3000 and the T2003; order model HKVN4045A. Manuals on CD are a no charge option (X347) for stations or upgrades; you must order the option it is not automatically included with a station order.
MOTOTRBO System Planner on CPS GMVN5141 CD and in Resource Center on MOL: MOTOTRBO System Planner MOTOTRBO IP Site Connect, Capacity Plus and System Brochure online, (also available on Digital Toolkit): http://www.motorola.com/Business/XUEN/Product+Lines/MOTOTRBO Introduction to MTR3000 Training https://techtrain.motorola.com/IntroductiontoMTR3000
106