Professional Documents
Culture Documents
As 3873-2001 Pressure Equipment - Operation and Maintenance
As 3873-2001 Pressure Equipment - Operation and Maintenance
AS 3873
maintenance
Australian Standard™
Australian Standard™
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
Originated as AS 3873—1991.
Previous edition 1995.
Third edition 2001.
COPYRIGHT
© Standards Australia International
All rights are reserved. No part of this work may be reproduced or copied in any form or by any
means, electronic or mechanical, including photocopying, without the written permission of the
publisher.
Published by Standards Australia International Ltd
GPO Box 5420, Sydney, NSW 2001, Australia
ISBN 0 7337 3749 8
AS 3873—2001 2
PREFACE
This Standard was prepared by the Standards Australia/Standards New Zealand Committee
ME-001, Pressure Equipment to supersede AS 3873—1995, Pressure equipment—
Operation and maintenance.
The Joint Committee agreed to produce this document as an Australian only Standard.
This Standard is a result of a consensus among members of Committee ME-001. Consensus
means general agreement by all interested parties. Consensus includes an attempt to remove
all objections and implies much more than the concept of a simple majority, but not
necessarily unanimity. It is consistent with this meaning that a member may be included in
the Committee list and yet not be in full agreement with all clauses of this Standard.
It was recognized that there was a need to specify requirements and give guidance to the
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
parties concerned with the operation and maintenance of pressure equipment. Existing
Standards specify requirements for design, manufacture and installation of pressure
equipment systems, but do not provide information for their operation or maintenance.
This Standard attempts to provide minimum requirements for a method of ensuring safe and
reliable operation of pressure equipment and for safety during maintenance, inspection,
alteration, storage and disposal. In some circumstances, additional requirements may be
necessary for adequate performance or safety. This Standard may be used as a guide for
training.
The main changes in this revision are as follows:
(a) Alignment with Standardization Guide No. 17.1, Drafting of Standards that may be
referenced under occupational health and safety legislation.
(b) A new appendix to give guidance on assessment of competency.
(c) Revised requirements and guidance on risk assessment to align with AS/NZS 4360,
Risk assessment.
(d) Revised Section 4, Safety management system, to become Appendix C.
(e) Incorporation of former Appendix J, Typical example of a generic risk assessment for
automotive fuel pressure vessels, into Appendix D.
The principal object of this Standard is to provide uniform, safe and economic requirements
and guidance for operation and maintenance of pressure equipment.
The terms ‘normative’ and ‘informative’ have been used in this Standard to define the
application of the appendix to which they apply. A ‘normative’ appendix is an integral part
of a Standard, whereas an ‘informative’ appendix is only for information and guidance.
3 AS 3873—2001
CONTENTS
Page
SECTION 4 BOILERS
4.1 GENERAL................................................................................................................. 21
4.2 OPERATING AND MAINTENANCE INSTRUCTIONS ......................................... 21
4.3 SHUTDOWN PROCEDURES .................................................................................. 25
4.4 TREATMENT OF WATER FOR BOILERS AND HEATERS ................................. 25
4.5 BOILER VALVES AND FITTINGS......................................................................... 26
4.6 OPERATION OF FITTINGS AND ACCESSORIES ................................................ 27
4.7 FAILURE OF BOILER PRESSURE PARTS ............................................................ 28
Page
APPENDICES
A LIST OF REFERENCED DOCUMENTS ................................................................. 36
B GUIDE TO THE APPLICATION OF A SAFETY MANAGEMENT SYSTEM
FOR PRESSURE EQUIPMENT................................................................................ 37
C USER’S DOCUMENTATION AND RECORDS ...................................................... 42
D RISK MANAGEMENT ............................................................................................. 44
E GUIDE FOR TRAINING AND SKILLS FOR BOILER OPERATORS.................... 53
F GUIDE FOR ASSESSING THE COMPETENCY OF PERSONNEL ....................... 56
G STORAGE PROCEDURES....................................................................................... 57
H TYPICAL PROCEDURE FOR STARTING UP A BOILER AFTER A MAJOR
OVERHAUL ............................................................................................................. 58
I TYPICAL REQUIREMENTS FOR FEEDWATER AND BOILER WATER
QUALITY ................................................................................................................. 61
J TYPICAL EMERGENCY PROCEDURE FOR LOSS OF WATER OR
LOW-WATER CONDITION IN A BOILER ............................................................ 65
K SOME MODES OF FAILURE OF BOILERS ........................................................... 67
5 AS 3873—2001
STANDARDS AUSTRALIA
Australian Standard
Pressure equipment—Operation and maintenance
1.1 SCOPE
This Standard specifies the minimum requirements and gives guidance on the operation and
maintenance of boilers, pressure vessels, associated control and safety equipment, piping
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
and auxiliaries, (e.g. boiler fuel handling and firing equipment, heaters, fans, pumps,
feedwater treatment and the like) and gives guidance in the execution of such work. It also
covers actions required from initial receipt of the equipment on-site until final disposal.
This Standard applies to commissioning, operation, maintenance, alterations, routine
inspection, dismantling storage and disposal. It includes specific requirements for safety
management systems, including, where appropriate, risk assessment.
Requirements cannot be written in sufficient detail to cover all aspects of the above.
Necessary action is required to ensure the continued safe operation of the pressure
equipment. This may require outside expert advice, which may typically include the use of
risk assessment or other appropriate methods.
This Standard generally applies to pressure equipment covered by AS/NZS 1200. The
extent of the application of the requirements is dependent on the hazard levels of the
equipment and service conditions.
NOTES:
1 ‘Duty of care’ is now prescribed on employers and employees regardless of regulation or
standards. This Standard does not supersede ‘duty of care’.
2 Users of this Standard are reminded that it has no legal authority in its own right, but may
acquire legal standing when adopted by government or an authority having jurisdiction, or if
specified as part of a commercial contract.