Professional Documents
Culture Documents
Aircraft Systems 2
Aircraft Systems 2
NOORUL ISLAM UNIVERSITY DEPARTMENT OF AERONAUTICAL ENGINEERING AE211/ AIRCRAFT SYSTEMS AND INSTRUMENTATION Short Questions (2 MARKS) 1) Name any four modern control systems? - Fly by wire (computer):- May be Analog computer or digital computer - Fly by optics (light):- Power by size (user electro-hydraulic actuators - Intelligent flight control system 2) What do you mean by active control technology? Give at least three examples? Activate control technology helps to improve the handling of aircraft and to reducethe time lag or control delays by increasing the no. of computers, etc., in the aircraft (i.e.redundancy). This advance concept in applicable to following e.g.. Examples are:- Fly by wire - Control configured vehicles - Automatic flight control system. 3) Name any four communication system? HF (High Frequency) communication for long range - VHF (Very High Frequency) communication for short range - Sat Com (Satellite Communication) - ACARS/AIRCOM 4) Name any four navigation system? - VHF Direction Finder (VDF) - NDB - ADF - GPS 5) What is INS used for? INS (Inertial Navigation System) is a sophisticated system for continuouslycalculating the aircraft track, ground speed and then convert this information in to otheruseful data. 6) Differentiate between instrument landing system and Microware landing system?
- In MLS, the A/C can approach from different directions, rather than having to fly to a position on the extended centerline of the run Cray in use. - MLS guidance is more accurate than ILS. - MLS increases the no. of A/C that can approach at name time. 7) What do you mean by VOR & CCV? VOR means (Very High Frequency Omni range) (Ref. to your notes as text book) CCV means (Control configured Vehicle) (Ref. to your care study) 8) What is ADF & NDB? - ADF means automatic direction finder (See notes or Text book) - NDB means non directional beacons (See notes or text book) 9) What is SELCAL & Sat Con? SEL CAL (selective calling) See notes 10) Differentiate between electric trim and manual trim? Electric trim is usually used to reposition stabilizer. Manual trim is used tooverride the elective trim. 11) What is difference between speed brakes and spoilers? Speed brakes are used for reducing the speed of A/C by increasing the drag. They also act as spoilers to spoil the lift Spoilers are used to spoil the lift for descending or landing. 12) Name any four control system components? - Bell crank - Walking beam - Sector & Quadrant - Torque tube 13) What is stabilators, ruddervators and flaperons? STABILATOR = STABILIZER + ELEVATOR (MOVABLE) RUDDERVATORS = RUDDERS +ELEVATORS FLAPERONS = FLAP + AILERONS 14) What is aileron differential control system? Movement of control stick moves one ailerons up greater than the other downwords.
3
15) What is the use of yaw dampers in rudder control system? Yaw damper systems operate continuously in flight to improve the airplanesdirectional stability and turn coordination. Dampers actuators are powered hydraulically. 16) What are the merits and demerits of analog and digital fly by wire flight controlSystem? See notes 17) Differentiate between fly by wire and conventional system? See notes 18) How is cable tensions measured? Tensometer 19) Name some advantages of fly by wire control systems? - Weight saving - Improved handling - Fuel saving - Reduced maintenance 20) Classify at least truce engine control system? - FADEC (Full Authority Digital Electronic/Engine control) - ECU (Electronic Engine Control) ECU can be manually over ridden by FADEC cannot (For details see notes) 21) What you mean by heat exchanger? A heat exchanges is any device by which heat in transferred from oneindependent system to another independent system. (See notes for details) 22) What is thermal relief value? A thermal relief value is similar to a regular system relief value bit such valuesare installed in parts of the hydraulic system where fluid pressure is trapped and mayneed to be relieved because of the increase caused by higher temperatures. (Refer notes of power pack for details) 23) Differentiate between single-acting and double acting actuating cylinder? A single acting actuator is normally used as a locking device the lock beingengaged by spring pressure and released by hydraulic pressure.The double acting actuator is used in most aircraft systems eg landing gear. 24) Differentiate between capon and closed hydraulic system?
An open system is one having fluid flow but no appreciable pressure in thesystem whenever the actuating mechanisms are idle. Its simple but only one servicecan be operated by this system at a time. (For diagram see notes) A closed system is one that directs fluid flow to the main system manifold andbuilds up pressure in that portion of the system the leads to all the selector values. Itsbit complicated but more than one service can be operated by this system at a time. 25) Classify air pressure sources? - Super charger - Turbo charger - Engine bleed air - Independent cabin compressors 26) What is a moisture control? The great reduction in temperature causes the moisture in the air to condense andthin moisture is removed by means of a water repeater. (For details see notes) 27) Differentiate between springs oleo struts and air oleo struts? In spring oleo struts, the spring supports the A/C weight on the ground and duringtaxiing and oleo strut aborts the shock of landing.In air oleo struts, the air supports the A/C weight on the ground and absents shocksduring taxiing and oleo strut aborts the shock of landing. 28) What is trunnion? The trunnion is the portion of landing gear assembly attached to the airframe. Thetrunnion in supported at its ends by bearing assemblies which allows the gear to pivotduring retraction and extension. 29) Explain the difference between dray strut and side strut? Draglink or drag strut is designed to stabilize the landing gear assembly longitudinally. Side link or side assembly laterally. 30) Classify the types of retraction system? - Mechanical retraction system - Electrical retraction system - Hydraulic retraction system 31) What is bungee cylinder used in landing gear? What is artificial bungee? The bungee cylinder: are mechanically linked to side brace links. They arehydraulically actuated & help in retraction of landing gears. Artificial bungee: gives feel factor to the pilot (for details see notes) 32) Differentiate between sequence and deposer value? See notes.
5
33) What is ply rating? Ply rating is an index of tire strength. The term is used to identity a given tire withits maximum recommended load. The higher the rating, the greater the load a tire willcarry. 34) Differentiate between expander shoe brake and expands tube brake? Expander shoal brake: Relation of break drum adds braking energy to the brake shoesand makes them operate more effectively & with Len effort by the pilot. They are alsoknown as serving brakes. Expander tube break: The pressure of hydraulic fluid in the tube forces the blocksradically outward against the break drum. 35) Differentiate between single disk brake and multiple disk breaks? Single disk brakes are used in smaller aircraft single disk may be conducted witha many separate pistons and linings as needed for the airplane. Each piston in equippedwith separate sets of linings, which bear against the brake disk when the brake seeapplied multiple disk brakes are used in large aircraft. Braking action is produced byhydraulic pressures forcing the pistons against the pressures plate, which, in turn, forcesthe disk together and creator friction between the retreating and stationary disks. 36) Differentiate between segmented rehear disk brake and carbon composite brakes? Segmented rater disk brakes are heavy duty brakes designed for use with highpressure hydraulic systems using power brake control values or power boost mastercylinders. Braking action results from several sets of stationary linings making contactwith rotating segmentsCarbon composite brakes: In this the disks are made of carbon. Its long-life, light weightcompared to steel brakes and more reliable. 37) Classify A/C break system & Landing gear? A/C Brake systems are: Landing gear - Independent brake system - Non absorbing landing gear - Power boost system - Shock absorbing landing gear - Power brake system - Fixed gear - Multi power brake actuating system - Retractable landing gear. 38) What is a master cylinder? The master cylinder in the energizing unit. There is one for each main landing yearwheel. It is a feet operated single action reciprocating pump, the purpose of which is tobuild up hydraulic fluid pressure in the brake system. (For diagram see notes) 39) What do you mean by anti skid system? Anti skid system are used to prevent loss of airplane control on the groundcaused by skidding of the wheels. The system consists of electronic controller,transducers, servo values, indicating light & switch.
6
(See block diagram from notes) 40) What are the advantages of pneumatic system over hydraulic system & voice versa? (See notes as Anna University solved Q paper) 41) What is surge fuel tank? Surge fuel tanks are normally empty and are designed to contain fuel overflow &prevent fuel spillage particularly when fueling the aircraft. (Far diagram see notes) 42) What do you mean by wet wing? An integral fuel tank is a tank that in part of the basic structure of the aircraft. When as integral type of tank is used in a wing, the air craft is said to have a wet wing 43) What is vapor lock? Vapor lock is a condition of fuel starvation that can occur in a reciprocating enginefuel system in which the fuel in the fuel line is heated enough to cause it to vaporize,forming a bustle of fuel vapor in the lime blocking fuel from flowing to the engine. 44) a) Classify fuel system? b) Why do we need primers? a) Fuel systems are - Gravity feed fuel system - Pressure feed fuel system b) Non fuel injected reciprocating A/C engines must often be primed beforestarting because carburetor is not functioning properly until the engine is running (For diagram see notes) 45) What is fuel cross feed system? On most multiengine air craft, the fuel manifold are connected in such a mannerthat any fuel tank may supply fuel to any engine, any tank can transfer fuel to other tankfor balancing. (For diagram see notes) 46) What is fuel Jettison or dumping system? In this system fuel from the tanks is continuous from using tip to using tip, witheach end terminating at a fixed fuel jettison nozzle. The nozzle value is an electrically aperated value controlled from the cockpit. After fuel passer through the nozzle value, itflows into the jettison nozzle to be discharged in to the air the jettison nozzle to be discharged in to the air.(for diagram see notes) 47) What is difference between defueling and jettison?
7
Defueling means draining the fuel out of the tanks when A/C is on ground.Jettison means dumping the fuel out of tank when A/C is in air fuel in dumped at the timeof emergency landing. 48) What is the purpose of fuel boost over ride & scavenge pump in fuel system? The central using tank boost pumps will over ride the main-tank boost pump tosupply fuel through the manifold to the engines. That s way its known as fuel boostoverride pump.Scavenge pump helps to prevent water from accumulating in the tanks low points. Thusavoids corrosion problems. 49) How will you select the starting system of the A/C? (See chapter 5 Engine starting system in A/F & power plant for details) 50) Enumerate the lubricating systems used jar jet engine? - Drug sump Lubrication: utilize an external tank mounted on the engine or somewhere in A/C structures near the engine. - Wet sump Lubrication: stores the lubricating oil in the engine proper. 51) Differentiate between fuel system of piston and jet engines? (See notes for details) 52) How does scavenge system work in lubrication? The scavenges system scavenges the main bearing compartments and circulatesthe scavenged oil to the oil coolers and bock to the tank. 53) What is breather pressurizing system? The breather pressurizing system ensures a proper oil spray pattern from themain bearing oil jets and furnishes a pressure head tee scavenge system. Breathermaintains an oil system pressure. It prevents over pressurizing. 54.- Capacitor type ignition system(jet) - Electronic ignition system (jet) - Battery ignition system P - Magnetic system (High tension) - Magnetic system (Low tension) 55. Clarity gas turbine engines starting system? 55. - Direct cranking electrical system -Starter generator systems -APU (Pneumatic) systems (see page 274 fees details) 56. Clarity reciprocating engine starting system? Cartridge starter - Hand inertia starter - Electric inertia starter
8
- Come inertia starter -Direct cranking starter 57. What is ignition exciter? (See notes) 58. Draw a neat diagram of typical electronic ignition system? Fig 4.77 page 233 at power plant hand book. 59. Differentiate between nigh tension ignition system & low tension ignition system? Magneto Ignition system operate on the principles of electromagnetic induction. They can be high tension & low tension ignition system. - High tension magnetic Ignition system High voltages are induced either by rotatingthe transformer windings between poles of permanent magnet or by rotating the magnetbetween fixed transformer windings car by rotating soft iron bass between fixedpermanent magnets and transformers winding. - Low tension magnate Ignition system then system were developed far engineerhaving large no of better then high tension. In this, the low voltage impulses from themagneto primary are directly supplied to the distributor. The low tension magnet issuited on and off similar to the high tension magneto. (See figure 4-16 & 4-17 for lowtension magnets) [In your text book A/F & power plant] 60. Draw a neat diagram of hydro mechanical fuel control? See notes car see page 157 of power plant hand book. 61. What do you mean by environmental system? Environmental systems are there aircraft systems used to make them interiorenvironment of the aircraft comfortable and/or habitable for human beings. 62. What is bleed air? When a compressor, compresses air price the directory it the engine combustionchamber, it gets heated up. This heat compressed air is called bleed air, which can bedriven to a cabin heating system. 63. What are A/C cooling system or air conditioning systems? Air craft cooling system are used to reduce the temperature inside and aircraft forcrew and passenger comfort. The two basic methods of reducing the temperature are thevapor. Cycle machine and the air cycle machine. 64. What are air cycle and vapor cycle machines? Air cycle machine:- The turbine, compressor unit by which air is cooled is called aircycle machine(ACM) The ACM user compression and expansion of
9
air to lower thetemp. of cabin air.Vapor cycle machine: - User refrigerant instead of air The vapor cycle machine in aclosed system usury the evaporation and condensation of Freon to remove heat from the cabin interior 65. What do you mean by purging the system? In vapor cycle refrigeration system, purging means releasing the refrigerant.In fuel system, purging means draining the fuel from tank by introducing inert gas as co2ar N2 to the tank.In oxygen system, purging means releasing oxygen from the system. 66. What is shirt sleeve environment? In order to make the cabin environment comfortable for the air craft occupants, thecabin must normally be pressurized to maintain the cabin air pressure at the level reachedat no higher than 800 it. This enables the crew and passengers to function without theuses of supplemental oxygen and, with adjustments of the cabin air temperature, allowsthem to be in a shirt sleeve environment. 67. Differentiate between super changer and turbo charger? A supercharger is an engine drive air pump; mechanically drive for engine, whichcompresses air for use by the engine in the combustion process.A turbocharger is used in a similar manner as a system charger except that the turbocharger is driven by exhaust gases from the engine, which driver an air compressed tosupply an air charge to the engine. 68. What is out flow value, safety or relief value, and negative pressure relief value?. Out flow value is discharge value - Pressure relief value x used at high altitude to reduce the over pressure. - Vacuum Relief values so negative or relief values are used at low altitude or groundin car the pressure in cabin in lend than out ride pressure 69. What is a cooling pack? Cooling packs consist of primary heat exchanger, secondary heat exchanger and air cycle machine (turbine &Comprador). They are used to cool the air 70 What is boot strap arrangement? 71. Differentiate between hypoxia and anoxia Hypoxia A lock of oxygen causes a person to experience a condition calledhypoxia. Systems are headaches, dizzimens etc.Anoxia when permanent physical damage results from lack of oxygen, the condition isanoxia.
10
72. Clarity oxygen system? 72. Continuous flow oxygen system. - Diluter Demand system - Pressure Demand system - Stored gas system - Chemical oxygen Generator or solid state generator system - Liquid oxygen system (LOX) 73. Write the chemical reaction in chemical oxygen or solid state generators? Naclo3 + Fe 1Dcl + FeO + 02 (Fuel) (See Fig. From Notes) 74. What are auxiliary systems? Systems not essential to the actual operation of the Aircraft are called auxiliarySystem. 75. What ways can ice be detected? -Visual detection -Electronic instrument 76. What is de-icing? De-icing means removing ice that has already farmed. 77. What is thermal anti-icing? Thermal anti-icing heated air flowing through passages in the leading edge of wings, Stabilizers and engine cowlings tee pre unit the formation of ice. 78. What is wind shield ice control? By heating the wind shield -By spraying a fluid on the windshield, to remove ice and present the formation ofany more ice 79. What is gasper system? The individual air- distributive system, also called the gasper system, routes only thecold air from the air conditioner packs to individually regulated outlets in the controland passenger cabins. 80. Name any three values used in pressurization system components? Out flow value - Positive pressure relief value - Negative pressure relief value 81. What is static balancing?
11
To eliminate the effect of cross wind or side slip the static resource in duplicated andis known as static balancing. 82. Evaluate TAS? 82. CAS= IAS+PEC -EAS= CAS+CEC -TAS= EAS+OEC (See notes fees details) 83. How is mach no. is inversely related to temperature M=V/a a = (RT)0.5 they for M is inversely related to T 84. What is the principal behind vertical speed indicator? 85. What is difference between SAT and TAT? 86. SAT(Static air temperature) This is the tem the air at the surface of the aircraftwould be at if there were no compression effects due to air craft is movement TAT (Totalair temperature) in the temp. Of the air when it has been brought completely to set, as inthe pilot tube. 87. The turn and bank indicates uses which of these:-Free gyro /tied gyro/ Earth gyro/rate gyro. Rate gyro. 88. How is gyro powered? Electrically & Pneumatically. 89. Name any three electronic display systems? Electronic height Instrument system (EFIS) - EICAS (Engine indicating and crew alerting system) -ECAM. (Electronic centralized air self monitoring) (For details see notes) What is flight management system? 90. Draw a block diagram of typical FMS (Flight management system) FMS in a Pilot interactive navigational com putting and display systems designedto assist in flying an air craft with the maximum economy and safety to a previouslyplanned route defined both laterally and vertically. 91) What is TCAS? Traffic collision Avoidance system 92) Show black diagram of flight data recorder?
12
93) Show black diagram of cockpit voice recorder? 94) What is BITE? BITE means Build In Test Equipment. BITE is a fault management and diagnosissbuilt into airborne systems to support the maintenance process. 95) What do you mean by AIDS & ACARS? ACARS Aircraft Communication Addressing and reporting system (see notes for detail) AIDS: Air craft integrated data system is an A/C system that allows the airlines to recordand /or monitor all available parameter which are on the aircraft buses. 96) What are the units of fuel consumption gauge? Fuel flow is: - Volumetric i. e gallons or liters per hour - Man \flow i.e. pounder (lb) or kilogram per hour. 97) How can use measure RPM of engine? - By Electronic Tachometer - By electrical Tachometer - By Magnetic Tachometer 98) What is multipurpose display? The multipurpose display is used for monitoring and revising the flight plan. 99) Explain the principle of Magnetic composes? It works on the principle that a freely suspended magnet will align relay with the earth magnetic field such that one end will point toward the north magnetic pole. 100) what is the purpose of artificial horizon? Artificial horizon (also known as attitude indicates) is used to provide the pilotwith an indication of the aircraft attitude in both pitch and roll. PART B (6marks)
1) Write short notes on fully powered flight control system. Power pumps Amplification Factor
13
3) Write detail about the push pull rod system? Rods Fittings Adjustments
7) Explain autopilot system with a neat sketch. 8) Write short notes on VHF Omni range system Very high Frequency
Shuttle Valve
10) Explain the hydraulic system with hand pump. Reservoir Selector valve Hand pump
Emergency system
14
13) Describe the fuel system for A/C with neat diagram? 14) Explain high & low voltage capacitor type ignition system. Magnetos 15) Explain the aircraft Hydraulic brake system? Drum Disk 16) Differentiate between fuel system of piston and jet engine? 17) Explain with neat diagram of Bank indication (Turn & back indicator display) 18) Explain the working of following with neat diagram- Altimeter and Airspeed indicators 19) Explain solid state oxygen systems? 20) Explain icing do-icing and anti -icing? PART C(10 MARKS) 1) What are the functions of push pull and flexible push pull red system? Explain with neat diagram? Power transmission 2) Explain how fully powered flight control system and power boated flight controlsystem work? 3) Explain the merits (advantage) and demerits (disadvantage) of analog and digitalfly by wire flight control system? 4) Explain the working and the advantage of auto pilot system? Accuracy Reduce the work load Efficient 5) Explain INS, ILS, MLS, VOR, ADF, NDBR selcal communication with neatdiagram? Ground station Tx Channel Space segment Rx Antennas 6) Explain the working of any two Engine control system with neat sketcher?
15
Piston engine Jet engine 7) Explain sequence value, Deposer value, relacter value, shut off value Cress feedvalue? 8) Explain the Basic hydraulic system with power driven pump with a neat sketch Reservoir Selector valve Hand pump Power pump Accumulators Valves Actuators
9) List out the components of the hydraulic systems? Explain at least four components with suitable diagram? Reservoir Selector valve Hand pump Power pump Accumulators Valves Actuators
10) Explain the types of landing gear in detail with neat diagram. Retractable fixed 11) Explain shimmy dampers in rose gears Air-oleo spring oleo shock struts in mainlanding gears? 12) Clan its airbrakes? Describe Expander tube brake system explain its working? Expander tube break: The pressure of hydraulic fluid in the tube forces the blocks radically outward against the break drum
16
13) Explain lubrication system used for piston and jet engine? Also explain electronicengine control? 14) Explain the starting system for the A/C? List out the gar turbine engine starters explain with neat diagram? 15) Explain with neat sketcher the air cycle cooling system and vapor cycle coolingsystem of an A/C 16) Explain icing do-icing and anti -icing? Discus pneumatic de-icing system? 17) What are cooling pales? Explain? 18) Explain the working of different fire detection and smoke detection techniquesused in A/C with neat sketches? 19) Classify different type of oxygen system? Explain solid state oxygen systems? Write down its advantages? 20) Explain the following with neat diagram: - Accelerometer - Capacitance type fuel level indicator - Flight data recorder - Thermocouple 21) Explain the working of following with neat diagram: - Electrical tachometer - Altimeter - Airspeed indicators - Mach meter 22) Explain with neat diagram - Gyroscopic instrument - Resistance type temperature measuring system - Magnetic tachometer - EHS & EAS relation 23) Explain the functional - Multi function display (MCDU) - EFIS - EADI & EHSI - EICAS & ECAM 24) Explain with neat diagram - Bank indication (Turn & back indicator display) - Heading indicates - Attitude indicates - Turn coordinator
17