Professional Documents
Culture Documents
Service Manual: Microwave Oven
Service Manual: Microwave Oven
: G37A50S001
Service Manual
Microwave Oven
Model: KOG-37A50S
Caution
: In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information,please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse. (c) Before turning on power to the microwave oven for any service test or inspection within the microwave generating compartments, check the magnetron, wave huide or transmission line, and cavity for proper alignment, integrity, and connections. (d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. (e) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner.
TABLE OF CONTENTS
SAFETY AND PRECAUTIONS .................................................................................................................2
1. FOR SAFE OPERATION............................................................................................................................................2 2. FOR SAFE SERVICE PROCEDURES.......................................................................................................................2
INSTALLATION .........................................................................................................................................6 OPERATIONS AND FUNCTIONS .............................................................................................................7 DISASSEMBLY AND ASSEMBLY ............................................................................................................8 INTERLOCK MECHANISM AND ADJUSTMENT...................................................................................17 TROUBLE SHOOTING GUIDE ...............................................................................................................18 MEASUREMENT AND TEST ..................................................................................................................20
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT..................................................................................20 2. MICROWAVE RADIATION TEST ............................................................................................................................21 3. COMPONENT TEST PROCEDURE ........................................................................................................................22
The door gasket plate and oven cavity surface should be kept clean. No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them. DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
IMPORTANT
The wire in this mains lead coloured in accordance with the following code. Green-and-yellow : Earth Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E, symbol or coloured green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
NOTE :
This oven is designed for counter-top use only.
SPECIFICATIONS
MODEL POWER SUPPLY MICROWAVE POWER CONSUMPTION GRILL COMBINATION MICROWAVE ENERGY OUTPUT MICROWAVE FREQUENCY OUTSIDE DIMENSIONS (WXHXD) CAVITY DIMENSIONS(WXHXD) NET WEIGHT TIMER FUNCTION SELECTIONS POWER SELECTIONS* CAVITY VOLUME *Specifications are subject to change without notice. KOG-37A50S 230V~50Hz, SINGLE PHASE WITH EARTHING 1200W 1050W 2200W 800W 2450 MHz 465 X 279 X 360 mm 290 X 220 X 306 mm APPROX. 13.4Kg 35 min. DUAL SPEED MICROWAVE / GRILL / COMBINATION 5 LEVELS 0.7 Cu. Ft.
EXTERNAL VIEW
1. Outer dimension
465
360
Power
0 35 30 25 20 15 10 9 8 7 6 1 2 3 4 5
279
Timer
2. FEATURE DIAGRAM
6
Power Timer
0 35 30 25 20 15 10 9 8 7 6 1 2 3 4 5
7 8
r ew
1 DOOR SEAL Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 2 REFLECTOR (Insulator Heater) 3 HEATING ELEMENT 4 OVEN CAVITY 5 SEFETY INTERLOCK SYSTEM 6 KNOB V.P.C Used to select a microwave power level. 7 KNOB TIMER Used to in setting cooking time for all functions. 8 DOOR RELEASE BUTTON By pushing this button the latch system cut off all circuits and stops the oven before the door is opened. 9 METAL RACK 0 COUPLER This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking. q ROLLER GUIDE This must always be used for cooking together with the glass cooking tray. w GLASS COOKING TRAY Made of special heat resistant glass. Food in a proper receptacle is placed on this tray for cooking. e DOOR VIEWING SCREEN Allows viewing of food. The screen is designed so that light can pass through, but not the microwave. r DOOR HOOK When the door is closed, it will automatically shut off. If the door is opened while the oven is operating, the magnetron will immediately stop operating.
INSTALLATION
1. Steady, flat location
This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter top use only.
5. Power supply
Check your local power source. This microwave oven requires a current of approximately 11 amperes, 230 Volts, 50 Hz. Power supply cord is about 1.4 meters long. The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage resulting from use of this oven with a voltage of ampere fuse other than those specified. This appliance is supplied with cable of special type, which, if damaged, must be reparied with cable of same type. Such a cable can be purchased from DAEWOO and must be installed by Qualified Person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity. If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing wire with a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
WARNING :
Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or serviceman if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or Do not use an extension cord.
0 35 30 25 20 15 10 9
1 2 3 4 5 6 7 8
NOTE :
1. When setting timer for less than 2 minutes, turn the timer past 2 minutes and then return to the correct timer setting. 2. Various clicking noises may be heard when turning V.P.C knob. This is normal and does not a ffect the operation o f your microwave oven.
To set MICROWAVE cooking Set the variable power selector to the desired power level. SYMBOL POWER LEVEL DEFROST MED-HIGH HIGH Approximate Percentage of Power 33% 77% 100%
To set GRILL cooking Set the POWER SELECTOR to the To set COMBI cooking Set the POWER SELECTOR to the
NOTE :
When using the GRILL or COMBI mode; Do not open the door so often, the temperature inside the oven decrease and the cooking may not be completed in setting time. Never touch the oven window and metal interior of the oven when taking food in and out, because the temperature inside the oven and door is very high. When using these modes, be careful as the tray will be hot to touch, use oven gloves or pot holders while handling tray.
(1) Check the earthed. Do not operate on a two wire extension cord. The microwave oven is designed to be used with earthed. It is imperative, therefore, to makes sure it is earthed properly before beginning repair work. (2) Warning about the electric charge in the high voltage capacitor. For about 30 seconds after the operation stopped, and electric charge remains in the high voltage capacitor. When replacing or checking parts, short between oven chassis and the negative high terminal of the high voltage capacitor, by using a properly insulted screwdriver to discharge. 4. When the 15A fuse is blown out due to the operation of the monitor switch; replace primary interlock switch, secondary interlock switch and interlock monitor switch. Refer to next page for the necessary adjustment. 5. After repair or replacement of parts, make sure that the screws are properly tightened, and all electrical connections are tightened. 6. Do not operate without cabinet.
CAUTION :
Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING :
When servicing the appliance, need a care of touching or replacing high potential parts because of electrical shock or exposing microwave. These parts are as follows-HV Transformer, Magnetron, HV Capacitor, HV Diode. HV Fuse.
1. To remove cabinet.
(1) Remove three screws on cabinet back. (2) Push the cabinet backward.
NOTE :
After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
DOOR AS : 3511710100
PART CODE 3512202060 3517003080 3515204100 3511706100 3517002800 3512300200 3513100700 3515101300
PART NAME FRAME DOOR BARRIER-SCREEN*O STOPPER HINGE*T AS DOOR WELD AS BARRIER-SCREEN*I GASKET DOOR HOOK SPRING HOOK
DESCRIPTION ABS SG-175, SG-0760D PC T1.0 KOR-63150S KOR-61150S PE T0.1 PP POM PW1
QTY 1 1 1 1 1 1 1 1
REMARK
(1) Remove the gasket door from door weld as. (2) Remove the barrier screen inner from door weld as. (3) Remove the door frame from door weld as. (4) Remove the stopper hinge top from door weld as. (5) Remove the spring and the hook. (6) Remove the barrier screen outer from door frame. (7) Reverse the above steps for reassembly.
10
4. Method to reduce the gap between the door seal and the oven front surface.
(1) To reduce gap located on part A. Loosen a screw on stopper hinge top, and then push the door to contact the door seal to oven front surface. Tighten a screw. (2) To reduce gap located on part B. Loosen two screws on stopper hinge under, and then push the door to contact the door seal to oven front surface. Tighten two screws.
Power Timer
0 35 30 25 20 15 10 9 8 7 6 1 2 3 4 5
NOTE :
A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2.
11
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
REF. NO B01 B02 B03 B04 B05 B06 B07 B08 B09 B10 B11 B12 B13
PART CODE 3513402680 3516709860 4415A17352 3515101600 3517402100 7122401211 7122401211 3518205630 3513402580 3513701420 441G430171 3516903650 3512766301
PART NAME KNOB VPC CONTROL PANEL SW MICRO SPRING FLAT COUPLER SCREW TAPPING SCREW TAPPING TIMER KNOB LEVER DOOR OPEN SPRING BUTTON BUTTON DOOR OPEN HARNESS TIMER
DESCRIPTION ABS SG-175, SG-0760D ABS SG-175, SG-0760D VP-533A-OF SUS T0.5 POM T2 PAN 4X12 PW MFZN T2 PAN 4X12 PW MFZN PW1 ABS SG-175, SG-0760D PP SWP ABS SG-175, SG-0760D KOG-37150S
QTY 1 1 1 1 1 1 2 1 1 1 1 1 1
REMARK
(1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. (2) Remove the door open lever from the control panel. (3) Remove two screws which secure the timer assembly. (4) Remove the timer assembly. (5) Pull out the timer knob from the timer. (6) Remove the screw which secure the V.P.C coupler. (7) Pull out the V.P.C coupler, V.P.C knob and flat spring from the control panel. (8) Remove the door open button and button spring from the control panel. (9) Reverse the above steps for reassembly.
12
7. To remove magnetron.
(1) Remove a screw which secure the magnetron. (2) Remove the magnetron. (3) Reverse the above steps for reassembly.
NOTE :
Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
Magnetron antenna
13
(1) Remove a screw for earthing. (2) Remove the noise filter from the wind guide. (3) Remove a screw which secure the wind guide assembly. (4) Draw forward the wind guide assembly. (5) Pull the fan from the motor shaft. (6) Remove two screws which secure the motor shaded pole. (7) Remove the motor shaded pole. (8) Reverse the above steps for reassembly.
9. To remove H.V.transformer.
(1) Remove four screws holding the H.V.transformer. (2) Remove the H.V.transformer. (3) Reverse the above steps for reassembly.
14
(5) Remove a screw which secure the tray motor. (6) Remove the tray motor. (7) Reverse the above steps for reassembly except for securing the tray motor cover with screw.
15
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
PART NAME NUT HEX SPACER INSULATOR *I INSULATOR HEATER HEATER SCREW MACHINE SCREW MACHINE
DESCRIPTION 6N-2-5 SUS C3771BD SPP T0.8 230V 1000W 1R67994001 TRS 5X6 MFCR TRS 4X4 MFCR
QTY 1 2 1 1 1 2
REMARK
16
ADJUSTMENT :
Interlock monitor switch When the door is closed, the interlock monitor switch should be opened before other switches are closed. When the door is opened, the interlock monitor switch should be closed after other switches are opened.
3. Adjustment steps
a) Loosen the one mounting screw. b) Adjust interlock switch assmbly position. c) Make sure that lock lever moves smoothly after adjustment is completed. d) Tighten completely one mounting screw.
NOTE :
Microwave emission test should be performed after adjusting interlock mechanism. If the microwave emission exceed 4 mW/cm2, readjust interlock mechanism.
17
(TROUBLE 1) Oven does not operate at all : any inputs can not be accepted.
Does the fan motor work when you shut the door and turn the timer? NO
YES
Check continuity of interlock mon itor switch with door shut. NO Continuity
Continuity
Replace fuse and check continu ity of both interlock switch's contact and monitor switch's contact with door partially open until monitor switch contact. Both Continuity
NO
Disconnec t one side of the lead wire connected from transformer to the high voltage capacitor, and operate oven.
Normal
Fuse again
NO Continuity
18
Does the fan motor work when you shut the door and turn the timer? YES
Does the oven lamp light? Does the turntable turn? YES
NO
NO Continuity
NO Continuity
Check the diode for continu ity in the reverse and normal d irections. Continuity
Replace magnetron. Meter with 6V or higher voltage batteries should be used to check the normal direction resistance o f the d iode.
NO Good
Replace magnetron.
19
PROCEDURE
1. Microwave power output measurement is made with the microwave oven supplied at rated voltage and operated at its maximum microwave power setting with a load of 100 5cc of potable water. 2. The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 3 mm and an outside diameter of approximately 190 mm. 3. The oven and the empty vessel are at ambient temperature prior to the start of the test. The initial temperature of the water is 10 2C (50 3.6F). If is measured immediately before the water is added to the vessel. After addition of the water to the vessel, the load is immediately placed on the center of the shelf, which is in the lowest normal position. 4. Microwave power is switched on. 5. Heating time should be exactly A seconds. (Refer to table as following) Heating time is measured while the microwave generator is operating at full power. The filament heat-up time for magnetron is not included. 6. The initial and final temperature of water is selected so that the maximum difference between the ambient and final water temperature is 5K. 7. The microwave power output P in watts is calculated from the following formula: P = 4187 X T/t T is difference between initial and ending temperature. t is the heating time. The power measured be B (Refer to SPECIFICATIONS) W 10.0 %.
NOTE
Microwave emission test should be performed after adjusting interlock mechanism. If the microwave emission exceed 4mW/cm2 , readjust interlock mechanism.
A (second) B (W)
70 600
64 650
60 700
56 750
52 800
49 850
47 900
44 950
42 1000
40 1050
38 1100
20
PROCEDURE
1. Prepare Microwave Energy Survey Meter, 600cc glass beaker, and glass thermometer 100C (212F). 2. Pour 275cc 15cc of tap water initially at 20 5C (68 9F) in the 600 cc glass beaker with an inside diameter of approx. 95 mm(3.5 in.).
35 30 25
Power Timer
0 1 2 3 4 5 6 15 10 9 8 7
3. Place it at the center of the tray and set it in a cavity. 4. Close the door and operate the oven. 5. Measure the leakage by using Microwave Energy Survey Meter with dual ranges, set to 2450MHz.
20
1) Measured radiation leakage must not exceed the value prescribed below. Leakage for a fully assembled oven with door normally closed must be less than 4mW/cm2. 2) When measuring the leakage, always use the 5 cm (2 in.) space cone with probe. Hold the probe perpendicular to the cabinet and door. Place the space cone of the probe on the door, cabinet, door seem, door viewing screen, the exhaust air vents and the suction air vents. 3) Measuring should be in a counter-clockwise direction at a rate of 1 in./sec. If the leakage of the cabinet door seem is unknown, move the probe more slowly. 4) When measuring near a corner of the door, keep the probe perpendicular to the areas making sure the probe end at the base of the cone does not get closer than 2 in. from any metal. If it does not, erroneous reading may result.
21
22
WIRING DIAGRAM
23
3. TOTAL ASSEMBLY
24
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
REF NO A00 B00 C00 F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34
PART CODE Refer to . Disassembly and assembly 3510805300 7112401011 3516109510 7S627W50X1 7122401211 3518904500 7121300611 7122401211 7112401011 35113A5QJ5 4413A90012 7112401011 7122401211 7S627W50X1 4414A25110 4414A25100 3518606100 7121402511 3963513100 3963512310 3512517000 G 3511800300 3518002400 3516004000 7272400811 3513003200 3518302200 3518400400 3518701100 3518113701 3516003700 3510311700 7112401011 3512100900 7272400811 3515201101
PART NAME DOOR AS CONTROL-PANEL AS INSULATOR HEATER AS CABINET SPECIAL SCREW CAVITY AS NUT HEX SCREW TAPPING T2S THERMOSTAT SCREW TAPPING SCREW TAPPING SCREW TAPPING CORD POWER AS CLAMP POWER CORD SCREW TAPPING SCREW TAPPING NUT HEX FUSE NOISE-FILTER SCREW TAPPING MOTOR SHADED POLE UIDE WIND FAN MAGNETRON SPECIAL SCREW TAPTITE SCREW HOLDER HV CAPACITOR CAPACITOR HV DIODE HV FUSE HV TRANS HV SPECIAL SCREW BASE SCREW TAPPING FOOT TAPTITE SCREW STOPPER HINGE*U
DESCRIPTION Refer to Disassembly and assembly KOR-61150S T1 TRS 4X10 SE MFZN KOG-37150S NUT FL M5X0.8P MFZN TRS 4X12 MFZN OFF:100 ON:90 HN #187 T2S PAN 3X6 MFZN T2S TRS 4X12 MFZN T1 TRS 4X10 MFZN 3X1.5 80X70 120-RTML NYLON66 T1 TRS 4X10 MFZN T2S TRS 4X12 MFZN NUT FL M5X0.8P MFZN 250V 15A 65TS 250V 15A MDA DWLF-M13 T2S PAN 4X25 MFZN 230V 17W OEM-10DWC2-A07 230V 20W MW10CA-M02 PP PP+30%GLASS 2M218J(F) T2 BOLT FL 5X12 DACRO TT3 TRS 4X8 MFZN SECC T0.6 2100VAC 0 .98mF #187 HVR-1X-3AB 12KV #187 5KV 0.55A HV-41A55-02 #187 DY-N80S0-63T TT3 HEX 4X8 FLG MFZN SBHG T0.7 T1 TRS 4X10 MFZN PP DASF-130 TT3 TRS 4X8 MFZN SCP-1 T2.5
Q'TY O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O
REMARK
KOG-37050S KOG-37050S
25
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
REF NO F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 F45 F46 F47 F48 F49 F50 F51 F52 F53 F54
PART CODE 7122401211 3518570400 4415A17352 4415A66910 4415A17352 3513702600 3513811700 3513601600 7121400611 3966310100 3966310110 3518905300 3513003400 7272400811 4078502031 3511405100 3517400620 3514700710 3512517300 3512517500 3517203600 3517206900
PART NAME SCREW TAPPING SWITCH S/A RELAY SW MICRO SW MICRO SW MICRO LEVER LOCK LOCK LAMP SCREW TAPPING MOTOR SYNCRO THERMOSTAT HOLDER THERMOSTAT TAPTITE SCREW BUTTON LOCKING COVER WAVE GUIDE COUPLER ROLLER GUIDE ROLLER GUIDE ROLLER AS TRAY TRAY RACK AS
DESCRIPTION T2S TRS 4X12 MFZN DWSR-1 VP-533A-OF SPNO #187 200G VP-531A-OF/SZM-V16-FA-61 VP-533A-OF SPNO #187 200G POM POM BL 240V 25W T25 C7A H187 T2S PAN 4X6 MFZN 20V 2.5W GM-16-24FD12 220V 2.5W M2LJ49ZT52 OFF:75 ON:65 H #187 NB PBT TT3 TRS 4X8 MFZN PP HONAM A353 MICA T0.35 XAREC TEFLON PP 5113MF6 A353B KOR-63150S GLASS KOG-37150S 110MM
Q'TY O O O O O O O O O O O O O O O O X X O O O
REMARK
26