Professional Documents
Culture Documents
Samsung Refrigerator Training 2003 Trainmnls
Samsung Refrigerator Training 2003 Trainmnls
Page 1
Table of Contents
The Samsung Difference Installation Cautions Refrigerator/Freezer Gasket to Cabinet Seal Test Sealed System Operation Functions Power Freeze Function Power Cool Function Child Lock Function Exhibition Function Self- Diagnostic Function Self-Diagnostics during Initial Power ON Self-Diagnostics during normal operation Load Operation Check Function Set Point Shift Function Defrost Function Forced Operation Function (Pull-Down / R-Defrost / R.F- Defrost) Circuit Operations Condenser Fan Delay Main PCB Power Supply Main PCB Main Micro Voltages Main PCB Lamp Circuits Main PCB Temperature Sensing Circuits Main PCB Display and Key Matrix CoolSelect Zone Circuit Damper Drive Circuit Main PCB Fan Motor Circuitry Main PCB Relay Control Ice Maker Circuitry Drinking Water Circuit Refrigerator Disassembly/Assembly Door Water Filter Evaporator Fan Evaporator Freezer Disassembly/Assembly Door Control Panel Door Gasket Icemaker Auger Motor Case Evaporator Fan Evaporator Machine Compartment Disassembly/Assembly Main PCB Water Solenoids Condenser Fan Sub Condenser Troubleshooting Tips and Bulletins TV Noise Exhibition Mode Filter Assembly Part Number Water Leakage from the Filter One Cycling Slow or no ice production Page 3 Page 4 Page 5 Page 6 Page 7 Page 7 Page 7 Page 7 Page 7 Page 8 Page 8 Page 8 Page 9 Page 10 Page 12 Page 12 Page 13 Page 13 Page 13 Page 14 Page 14 Page 15 Page 17 Page 18 Page 18 Page 19 Page 20 Page 21 Page 23 Page 24 Page 24 Page 28 Page 29 Page 29 Page 30 Page 30 Page 33 Page 33 Page 34 Page 35 Page 37 Page 37 Page 38 Page 38 Page 39 Page 39 Page 39 Page 40 Page 40 Page 41 Page 41 Page 42 Page 42 Page 43
Page 2
1. Twin Cooling System a. In this system, the refrigerator and the freezer have two separate evaporators. The freezer and the refrigerator are cooled individually and are therefore, more efficient. Food odor from the refrigerator does not affect food in the freezer due to separate airflow circulation. b. Each evaporator has its own fan, both of these fans circulate cold air in their respective compartments. 2. Multi-Flow System a. Within this system, cool air circulates through multiple vents on every shelf level in both compartments. This provides even distribution of cooling inside cabinets to keep food fresh longer. (See figure 1)
Figure 1
Page 3
Installation Cautions
1. To protect refrigerator when moving Use a padded hand truck to avoid damage to unit. If entrance width is less than 39, remove doors prior to installation and reattach doors by following the procedure below. Removing Doors a. Open the freezer and refrigerator doors, then take off the front leg cover assembly by turning the three screws counter-clockwise. Remove the screw from the clamp holding the water tube. Disconnect the water tube by pressing the coupler in, and pulling the water tube out. (See Figure 2) b. With the door closed, remove the upper hinge cover using a screwdriver, and then disconnect the wires hidden underneath it. Remove the hinge screws and the ground screw by turning counterclockwise, and take off the upper hinge. (See Figure 3) Take care removing the door to ensure that it does not fall on you. c.
Figure 2
Figure 3
Remove the door from the lower hinge by carefully lifting the door so as not to damage the water tube. Remove the lower hinge from the lower hinge bracket by lifting the lower hinge (See Figure 3) d. Refer to Disassembly/Assembly instructions starting on page 24 of this Training Guide for more door removal procedures. Attaching Doors a. Insert the lower hinge in the bracket lower hinge. (See Figure 4) Attach the freezer door by inserting the hose in the lower side of the door into the hole in the lower hinge and pulling the hose down. b. Insert the upper hinge shaft into the hole while leveling the upper hinge and cabinet holes. Reattach the hinge screws and screw them in. Connect the wire harnesses. Put the front part of the upper hinge cover on the front part of the upper hinge and reattach. (See Figure 5) c. Refer to Disassembly/Assembly instructions starting on page 24 of this Training Guide for more door attaching procedures. Figure 5
Figure 4
Page 4
Refrigerator/Freezer Gasket to Cabinet Seal Test In the event that a customer complains about cold air leakage from the Refrigerator/Freezer in the area where the gasket seals up against the cabinet, perform the following test. This test should also be performed anytime a door or gasket is replaced. 1. Tear a piece of paper two to three inches wide by eight inches long. (A standard note pad page, cut to size, is sufficient. DO NOT fold the paper to size.) NOTE: The paper should be no smaller than two inches in width. 2. Open the Refrigerator/Freezer door. 3. Place the paper between the Refrigerator/Freezer cabinet and door in a way that it will be "sandwiched" between the gasket and cabinet. 4. Close the door with approximately a quarter of the page protruding out from the door. This will facilitate pulling the paper. 5. Pull gently on the paper. A small resistance to the pull should be felt when applying a gentle pull on the paper with two fingers. This is normal and sufficient to confirm that the gasket is sufficiently seated against the cabinet. 6. Perform the pull test around the perimeter the Refrigerator/Freezer door to confirm that all locations are sealing properly. In the event that the paper pulls freely with no effort, the gasket is not sealing properly and it is recommended that the gasket and/or door assembly be replaced. 2. Remove all protective tape and padding in refrigerator Connect water lines and power cords. Make sure to adjust the clearance between the doors. 3. Set the temperature control to the desired temperature and wait for an hour The refrigerator should get slightly chilled and the motor will run smoothly. 4. Once the refrigerator temperature is sufficiently low You can now store food in the refrigerator. After starting the refrigerator, it takes a few hours to reach the appropriate temperature. When the systems power is initially engaged, the default set temperatures are 4 degrees for the freezer and 38 degrees for the refrigerator, respectively.
Page 5
Sealed System This system is in charge of the refrigeration cycle and the cool air circulation route. The responsibility for each of the major components is as follows:
Figure 6 1. 2. 3. 4. 5. 6. Compressor - When the compressor is on, it forces the gas through the system. Sub Condenser - Used to cool down the system. Side Cluster Pipe - Used to cool down the system. Hot pipe - Designed to prevent condensation. Dryer - Used to control condensation. Capillary Tube - Controls the pressure and flow of the refrigerant as it enters the evaporator. 7. Freezer and Refrigerator Evaporators - Causes a pressure drop, this drop turns the refrigerant to gas. 8. Suction Pipe - Attached to the compressor, used to transport the gas.
Page 6
Operation Functions
1. Power Freeze (Quick ice) Function When the Power Freeze (Quick ice) button is pressed the LED indicator will immediately light up. Please allow 10 seconds lag time to begin the actual operation. When this button is pressed again, the power freeze (Quick ice) function stops and the indicator will turn off. If you select Power Freeze (Quick ice), the interior temperature of the freezer will be set to -14 degrees Fahrenheit, until the ice bucket is filled up with ice cubes. When the ice bucket is filled up, the freezer will return to its original set temperature. Also, whenever the ice bucket full lever bar is released from being filled with ice cubes, the freezer will return to the Power Freezer (Quick ice) function as long as the function is selected. Press the Power Freeze (Quick ice) button twice to cancel. If you use this function, energy consumption will increase. Please turn off when not using this function. Note: When the Power Freeze (Quick ice) is selected, it enables maximum ice making output. The ice-making interval is reduced from 130 minutes per tray to 92~105 minutes. (Ice making times and quantities for 24 hours will increase to approx. 15 trays/156 cubes) 2. Power Cool Function Power Cool operation and the indicator work similarly to the Power Freeze (Quick ice) function. When power cool is selected, the Compressor and the Refrigerator-Fan operate continuously until the refrigerator reaches 25 degrees Fahrenheit. This function will be terminated after running for 2 hours. 3. Child Lock Function When the child lock button is pressed for 3 seconds, the child lock indicator will come on with an audible tone. When the lock function is initialized, no function commands except the ice type button will be accepted, this function will prevent accidental setting that may be caused by children or pets. To unlock the setting function, press this button for 3 seconds again. 4. Exhibition Function This function is for display purposes on the floor of a showroom or store. For the exhibition mode, press Power Freeze (Quick ice) and Freezer Temp. buttons simultaneously for 8 seconds until ding dong sounds. In this mode, most of the unit will function normally, all except the compressor and the sealed system, which will not operate. Also, there is no defrost cycle in this mode. Press Power Freeze (Quick ice) and Freezer Temp. buttons again for 8 seconds to cancel this mode. You will hear a ding dong sound.
Page 7
Page 8
Figure 9
Page 9
Page 10
Note: Setting the differential temperature on the Icemaker too high could cause the following: 1. Not fully frozen Ice. 2. Ice cubes sticking together.
Page 11
Defrost Function
A defrost cycle is determined based on the accumulated compressor on time. When the power is engaged for the first time, the defrost cycle for the freezer and the refrigerator will begin after 4 hours of accumulated on-time of the compressor. A defrost interval depends on the ambient temperature, the number of door openings, and the door open time. A minimum interval is 6 hours and a maximum is 8 hours for the refrigerator, and 12 hours to 16 hours for the freezer respectively. The defrost heater on-time is determined by the defrost sensors.
Page 12
Circuit Operations
Condenser Fan Delay Depending on the ambient room temperature, the condenser fan will operate in different modes. See figure 10 for the location view of the Condenser Fan. See figure 11 below for the operation table.
Figure 10
Figure 12 The SMPS (Switch Mode Power Supply) converts the AC input voltage (115V, 60Hz) to a high DC voltage (170V) on the primary side of the Transformer. This converted DC power will be sensed in all of the windings of the Switching Transformer and will generate a constant waveform on the transformer using the high speed (100KHz) switching motion of TOP223Y (FET). The diode D104 will rectify the generated voltage into a steady 12Vdc, which is the source power used for the digital display panel and relays. The regulator (KA7805) down converts the 12Vdc into the 5Vdc source for the control board and sensors circuits. The Photo-Coupler PC817 is used as a feedback regulator in conjunction with the voltage divider (R102 / R103) and ZD2 to ensure that the 12Vdc line maintains the proper level.
Page 13
Main PCB Main Micro Voltages VDD is located at pin 64 of the Micro. The voltage at this pin should be a steady 5Vdc. The Crystal Oscillator is located between pins 30 and 31 of the IC. The Crystal generates a sine wave voltage of approximately 3.3Vp-p. The Micro Reset is applied to pin 29. This is a low level reset so this pin will normally read 5Vdc. The Ground pin of the Micro is pin 14.
Figure 13
Figure 14 Figure 14 above shows the Ref and Freezer Lamp circuits. The state of the circuit pictured here is with both doors closed and the lamps off. Lamp Activation occurs when a door is opened and the switch changes contacts to allow current flow through the lamp. When a door is opened and the appropriate switch changes state, the Micro senses this as a high being applied to either pin 43 or pin 44. The Micro will detect how long the door was opened when the switch changes state again and pins 43 and 44 return low. Door openings are calculated to determine the time the Compressor will be on and how long it takes to make a tray of ice.
Page 14
Main PCB Temperature Sensing Circuits All six Thermistors are negative temperature coefficient (NTC) type sensors. This means that their resistance value will decrease when there is an increase in the temperature level around them. The resistance value of the thermistor will increase when the temperature decreases. There are four Thermistors in the Freezer, and two in the Refrigerator section. The Freezer Sensor is used during the cooling cycle to ensure that the proper cabin temperature is maintained in the freezer. A voltage divider is set up between the Thermistor and R303. The input voltage into pin 56 of the MICRO, is calculated by the following formula: (Rth x Vcc)/(R303+Rth) Where Rth is a corresponding resistance to the thermistors output. See Appendix 1. So, Figure 15 when the proper voltage level is applied to pin 56 of the Micro, the Freezer Fan will turn off. When that voltage level decreases due to a temperature increase in the freezer side the fan will turn back on during the cooling and defrost cycles. The Freezer-Defrost Sensor is connected with a Bimetal in parallel. In the normal cooling operation of the system, the bimetal is on and a voltage level of 0V (Ground) is input into the microprocessor. The Bimetal be closed when the temperature is 23 F or lower. Pin 57 is ignored during the cooling cycle. The Bimetal is the principle sensing element for the thermistor, during the defrost cycle the Bimetal will open above 54 F, and a divided voltage with the Thermistor and R304 will be sent to the microprocessor to keep sensing the freezer temperature. (The Bimetal is not applied for the products produced after the first of June) The Refrigerator Sensor operates in a similar fashion to the Freezer Sensor, so the voltage level detected at pin 59 of the Micro controls the Refrigerator Fan. The Refrigerator Defrost Sensor has no Bimetal, so pin 60 of the Micro monitors a true voltage divider during the defrost cycle to turn the Refrigerator Fan on and off to maintain the proper cabin temperature of the refrigerator. The Ambient Sensor is located on the outside of the unit on top of the Freezer section and is a part of a similar voltage divider circuit like that of the Freezer Sensor. This sensor is needed to determine fan speed as compared to the surrounding temperature of the unit. The Ice Maker Sensor (not shown in Figure 15) is used to alert the Micro of the temperature level inside the Ice Maker compartment. This is important since the Temp level is part of the calculation for determining the amount of time it will take to dump a tray of ice. The Ice Maker Sensor is a standard voltage divider circuit just like the F & R Sensor circuits.
Page 15
For troubleshooting, see figure15 for Sensor test point and use Appendix 1 for the proper resistance measurements. Remember these resistance measurements should be taken when the main power is disconnected from the appliance. Also the connector to the Main PCB should be disconnected to achieve reliable readings of the sensors.
Appendix 1
Page 16
Figure 15 Display Operation This model uses a decoder IC that has 4 inputs and 9 outputs. If the IC 9 decoder receives signals from Micro pins (3-6), this data will be out the Decoder in a sequence to the freezer door display. Pins 9, 14 and 15 are used for the CoolSelect Zone display. Key Scan Function IC9 is a Decoder IC that outputs pulse signals to the six scan lines of the key matrix. When a button is pressed, the corresponding signal will be sent to the Micro at pin 34, and the function will be executed by the Micro.
Page 17
Figure 16 The CoolSelect Zone is a storage drawer used to implement the following functions: Quick Cool, Thaw, and Temp. Selection (Soft Freeze, Chill, and Cool). The CoolSelect Zone has its own additional display panel located inside the refrigerator compartment. The panel LEDs are off while the door is closed. When the refrigerator door is open, the microprocessor will sense this from the status of the door switch, and the LEDs will function. The additional sensor used in this circuit is interfaced using a three pin connector CON3. This sensor is used to measures the temperature of the CoolSelect Zone compartment only. Pin 58 of the micro is the input for sensing this Thermistor. This sensor enables the microprocessor to control the temperature of the CoolSelect Zone.
Page 18
Figure 17 This refrigerator adopts BLDC (Brushless Direct Current) motors to reduce energy consumption. Under certain conditions, the fans will operate in 2 modes (High) or (Low) speed. Generally, the fans operate in the High mode during the day and in the Low mode at night. This function is controlled partially by how many times the doors are opened and closed during operation and the condition of the Ambient Sensor. The chart listed below gives the voltages for test points of the motors at high and low speeds. See figure 17 above for the specific test points.
High Low
Voltage of Motor Test Point b Test Point c Test Point d (F-Fan) (R-Fan) (C-Fan) 11.1V 10V 10V 10V 10V 8.3V
Remark
Fan operation would be detected at pins 40, 41 & 42 of the Micro. (Freq (Hz) x 12 = motor rpm)
Troubleshooting:
Fan resistance measurements checking via connector CN72. All measurements are referenced from pin 7 (Com) of connector CN72 (disconnected). CN72 Pin 6 Pin 5 Pin 4 Resistance 2K 1.6K 1.2K CN72 Pin 3 Pin 2 Pin 1 Resistance 17.7K 18.2K 7.6K
Page 19
Figure 18 Compressor Control The Compressor is controlled by pin 18 of the Micro. RY73 is the Relay used to complete the electrical circuit when the switch is in the bottom position. Defrost Heaters Control The Freezer Defrost Heater is controlled by pin 16 of the Micro via Relay RY71. Pin 17 of the Micro is used to control the Refrigerator Heater via RY72. Both Heaters use pin 11 of connector CN70 as a hot connection and pin 3 as a common. Each Heater has a Thermal Fuse connected in series with it. Thermal Fuse Troubleshooting: Freezer Thermal Fuse = 49.3 Ohms (Normally) Refrigerator Thermal Fuse = 94.3 Ohms (Normally) Sub Heaters Control The Home Bar, Dispenser and Water Tank Heaters are all controlled by pin 19 of the Micro through RY74.
Page 20
Figure 19 Figure 19 above shown the Ice-Maker control circuitry. The Ice Maker Sensor is used as part of a voltage divider. This thermistor has a negative temperature coefficient (NTC). This means that its resistance value will decrease when there is an increase in the temperature level around it, and the resistance value of the thermistor will increase when the temperature decreases. This voltage divided level is monitored at pin 61 of the Micro and is one of the sources to determine the amount of time to dump a tray of ice. Pins 7 and 8 of the Micro are used to activate the Ejecting Motor during an ice cube dump. Pin 8 is the source to turn the motor in the Counter Clockwise direction to dump the ice, and pin 8 turns the motor back in the opposite direction to level the ice tray out. IC4 and IC5 are the Drivers Amps used to apply enough torque to the motor. The Test SW is the black button located on the Ice Maker Assy. Press this button to simulate an ice dump to ensure proper operation of the Assy. When this button is
Page 21
pressed, the motor will be activated to turn (twist) the ice tray into the position where the ice would be dumped out of it. During this time, the Level SW will be closed. This applies a low to the Micro pin 51 to inform it that the ice tray is not in the normal (Flat) position. The motor will then be commanded to reverse rotation so that the tray returns to the normal position and the Level SW opens. Once this is detected by the Micro, the Ice Solenoid Valve will be turned on via RY75 to supply water to the ice tray for the next cycle to begin. The Ice Full SW is connected to the big Guide Ice Lever that runs parallel to the ice tray. When the amount of ice in the bucket pushes the level up far enough, this switch will close and the Ice Maker will stop producing ice. When the amount of ice in the bucket reduces to a low enough level so the Level SW opens, the Ice Maker will start producing ice again.
Figure 20
Page 22
Figure 21
Figure 21 above shows the water flow lines throughout the unit. The main components involved here are the Filter (Shared), the Valve (Separation), Water Tank (Water Option Only) and the Ice Maker (Ice Option Only). The Water Filter is located in the upper right corner of the Refrigerator cabinet. The Valve is located in the rear mechanical compartment on the lower right side looking at the unit from the back. When the Water SW is depressed on the freezer door, power will be applied to the water line side of the valve, and water will flow into the Water Tank. This will continue on past the Check Valve and out the water hose on the front. The Check Valve is used to eliminate any dripping from the water hose when the Water SW re-opens. When the ice tray returns to the level position after dumping the ice, RY75 on the Main PCB will activate and apply power to the ice portion of the valve. Water will then flow for a set duration to re-fill the tray.
Page 23
(Refrigerator) Disassembly/Assembly
Refrigerator Door Removing the Front Leg Cover Open the freezer and refrigerator doors, and then take off the front leg cover assembly by turning the three screws counterclockwise. See figure 22. Separating the Water Supply Line from the Refrigerator Remove the screw from clamp (a).
Figure 22 Remove the water tube by pressing the coupler (2) and pulling the water tube (1) away. See figure 23.
Figure 23
Page 24
Disassembly With the door closed, remove the upper hinge cover (1) using a screwdriver, and then disconnect the wires (2). See figure 24.
Figure 24 Remove bolts (3) and ground screw (4). Then take off the upper hinge (5) in the direction of the arrow (6). Take care when removing the door to ensure that it does not fall on you.
Figure 25 Remove the door from the lower hinge (7) by lifting the door (8) in the direction of the arrow. See figure 26.
Figure 26 Remove the lower hinge (9) from the bracket lower hinge (10) by lifting the lower hinge (9) in the direction of the arrow. See figure 27.
Figure 27
Page 25
Assembly
Insert the lower hinge (1) in the lower bracket (2). See figure 28.
Figure 28 Place the hole in the refrigerator door (3) over the lower hinge (4). See figure 29.
Figure 29 Insert the upper hinge shaft (5) into the hole (6). After leveling between the upper hinge hole (7) and the hole of the cabinet (8). Reattach bolt (9) and screw (10). See figure 30.
Figure 30 Connect the wires from the door to the cabinet. See figure 31.
Figure 31
Page 26
Put the upper hinge cover (11) on the front part the hinge (12). Reattach the front part of the cover first. See figure 32.
Figure 32
Figure 33 While pressing the front face of coupler (2), insert the water tube (1) in the coupler. Then tighten the screw on the clamp (a). Reattaching the Front Leg Cover Reattach the front leg cover and tighten the three screws down, as shown in figure 34.
Figure 34
Page 27
Water Filter
The water filter is located in the rear upper right-hand corner of the refrigerator. The water filter is used to filter the water for both the icemaker and the water dispenser. Removal: Turn the water filter turn counterclockwise and pull it down. Installation: Align the filter with the indication mark (unlock position) and push it up while turning turn clockwise until the lock position is aligned. Do not over-tighten. Figure 35 Filter Indicator: The indicator initially lights green. The light color will change to orange after five months of operation then to red on the 6th month. The EEPROM in the control board counts a period of time regardless of a power failure. To reset the counter and the light color, press and hold the ICE TYPE and CHILD LOCK buttons for 3 seconds simultaneously. If these two buttons are pressed simultaneously for 5 seconds, this function will cease. To restore this function, press these buttons again for 3 seconds.
Evaporator Cover In The Refrigerator 1. Pull out the screw cap and remove the screw. 2. Remove the lamp cover by unlocking the tabs and pulling the cover down. 3. Remove the water tank from the evaporator cover by unscrewing the 2 screws at the bottom of figure 36. 4. Remove the 6 screws of the evaporator cover and the 2 fixed screws of the wire connector cover. 5. Take off motor and lamp wire connector located on the upper liner. 6. Remove the ductwork of the evaporator fan.
Figure 36
Page 28
Upper Ductwork
1. Remove the screw caps (2) and screws (5). 2. Slide the upper fan ductwork out while disconnecting the wire connector(lamp and thermistor) as shown in figure 37.
Refrigerator Evaporator Fan Motor The evaporator fan is located in the middle rear of the refrigerator compartment. This fan circulates cold air in the refrigerator section when activated. 1. Remove the 4 screws located at the corners of the fan bracket. 2. Take the fan assembly off the cover. Evaporator in Refrigerator Evaporator is located in the bottom back of the refrigerator compartment. 1. Take off the ductwork in refrigerator. 2. Disconnect the wire connector. (Heater and Thermistor) 3. Desolder the capillary tube and the suction line from the evaporator. 4. Remove the evaporator. 5. With a file, score the capillary tube just upstream of the soldered point. Break off the soldered section to help prevent solder from plugging the tube during soldering. 6. Insert a new evaporator and braze the suction and capillary tube to the evaporator using silver solder. 7. Install a replacement dryer. Note: Evacuate and recharge the system using normally approved procedures.
Figure 37
Figure 38
Figure 39
Page 29
(Freezer) Disassembly/Assembly
Freezer Door
Removing the Freezer Door Disassembly With the door closed, remove the upper hinge cover (1) using a screwdriver, and then disconnect the wires (2). See figure 40.
Figure 40 Remove bolts (3) and ground screw (4), and take off the upper hinge (5) in the direction of the arrow (6). Take care when removing the door to ensure that it does not fall on you. See figure 41.
Figure 41 Remove the door from the lower hinge (7) by lifting the door (8) in the direction of the arrow. See figure 42. NOTE: Lift the door straight up to prevent damage to the bottom hinge. Be careful not to pinch the water tubing and wire harness on the door. Place doors on a protected surface.
Figure 42 Remove the lower hinge (9) from the bracket lower hinge (10) by lifting the lower hinge (9) in the direction of the arrow. See figure 43.
Figure 43
Page 30
Assembly Insert the lower hinge (1) in the lower bracket (2).
Figure 44 Reattach the freezer door by inserting the hose (3) from the lower side of the door into the hole of the lower hinge (4), and pull the hose down.
Figure 45 Insert the upper hinge shaft (5) of the cabinet into the doors hole. After adjusting the level between the upper hinge hole (7) and the hole of the cabinet (8), reattach the three bolts (9) and screw (10).
Figure 46
Page 31
Figure 47 Put the front part of the upper hinge cover (11) on the front part of the upper hinge (12) and reattach from the front part of the upper hinge cover first. See figure 48.
Figure 48
Page 32
Disassembly/Assembly Control Panel Disassembly: Insert a flat-head screwdriver in the slots located on the bottom of the control panel and unlock the tabs. After removing the panel, disconnect the wire connector from the PCB. Assembly: Connect the wire connector back to the PCB. Line up the panel and snap the locking tabs back into place.
Figure 49
Door Gasket, The door gasket is a molded into a channel located in the door liner. 1. Open the door. 2. Grasp the gasket and pull in an outward motion until the molded gasket separates from the door liner. Note: Reference Gasket Seal Test procedures on page 5 of this manual.
Figure 50
Page 33
Ice Dispenser And Ice Maker The ice dispenser is located in the upper left hand portion of the freezer. This assembly is used to store ice made by the icemaker and dispense the ice. Lift the ice bucket up and slide out the ice dispenser assembly .
Figure 51
Removal 1. Remove the 2 icemaker support screws and slide out the assembly. 2. Disconnect the icemaker wire connector. 3. Unlock the locking tabs to separate the icemaker kit.
Figure 52 Assembly 1. Assemble together the geared motor shaft and the front of ice tray. 2. Lift the front locking tab and assemble the icemaker kit. 3. Connect the icemaker wire connector. 4. Match the tab holes and 2 tabs located on the top of the liner, and slide the icemaker into position. 5. Tighten the 2 screws to the icemaker support.
Figure 53
Page 34
Auger Motor Case This shelf is designed to support the icemaker / ice dispensed and the Xtra-Space area. 1. Remove the Xtra-Space cover by pushing it down and pulling it forward. 2. Slide the partition out. 3. Remove the 2 screws on the bottom front of the case. See figure 54. 4. Slide out the case while disconnecting the wire harness behind it. Figure 54
Page 35
Evaporator Cover in Freezer 1. Pull out the screw caps and remove 6 screws. 2. Remove the ductwork of the evaporator fan in the direction of the arrow as shown. 3. Disconnect the wire connector in the rear of the cover as shown in figure 55.
Figure 55 Upper Ductwork 1. Remove the screw cap and screw. 2. Slide the upper fan ductwork out while disconnecting the wire connector (Lamp and Thermistor) as show in figure 56.
Figure 56
Page 36
Freezer Evaporator Fan Motor The evaporator fan is located in the midsection of the freezer compartment. This fan circulates very cold air in the freezer when activated. 1. Remove 4 screws located at the corners of the fan bracket. See figure 57. 2. Take the fan motor assembly off.
Figure 57 Evaporator in Freezer The Evaporator is located in the lower to middle section of the freezer compartment. 1. Take off the ductwork in Freezer. 2. Disconnect the wire connector (Heater, Bimetal, and Thermistor). 3. Desolder the inlet and outlet tubes. 4. Remove and replace the evaporator. 5. Take the same steps to seal the system as mentioned in the refrigerator evaporator removal procedures on page 29 of this Training Manual.
Figure 58
Page 37
Machine Compartment Disassembly/Assembly Machine Compartment and Electric Box 1. Disconnect the power cord of the refrigerator. 2. Remove 6 fixed screws of the compressor cover.
Figure 59 3. Slide up and take off the compressor cover to see the machine compartment.
Figure 60
Main PCB 1. Remove 2 screws to remove the Electric Box from the machine compartment. 2. Pull the box out of the compartment so that it is hanging on the floor. 3. Press the tab in electric box cover with a flat head screwdriver to separate the top cover from the bottom and expose the main PCB.
Figure 61
Page 38
Water Solenoids There are two solenoids in one package. One is for the water dispenser, the other supplies water to the icemaker. Both are controlled by the Micro located on the Main PCB. 1. Remove 1 bracket screw on electric box. 2. Take the solenoids assembly out of the machine compartment. 3. Disconnect the 3 water tubes.
Figure 62 Condenser Fan The condenser Fan is located in the middle of machine compartment. It blows out the hot air in the machine compartment created by the Sub Condenser and the Compressor. 1. Disconnect the condenser fan wire. 2. Remove 1 screw on the drain water tray. 3. Take the condenser fan assembly out.
Figure 63 Sub Condenser The sub-condenser is located in the machine compartment. The heat is extracted by condenser fan. 1. Desolder the compressor discharge and the sub-condenser outlet. 2. Take out the sub-condenser.
Figure 64
Page 39
SYMPTOM: The complaint will be no cooling in either the Freezer or Refrigerator compartments. The Compressor is not activating. However, the button and indicators on the front display operate normally and the internal lights turn on when the doors are opened. REPAIR: The unit might be in the Exhibition Mode. This is a normal function of the refrigerator for display on the Dealer show floor. Use the following procedure to exit the Exhibition Mode: Hold down the POWER FREEZE and FREEZER TEMP buttons simultaneously for eight seconds until the unit makes an audible tone.
SYMPTOM: Missing part number for the water filter receptacle assy. REMARKS: Part Number (DA97-00725B)
Page 40
SYMPTOM: Water leaking at the filter. REMARKS: If the filter is installed incorrectly, it will leak water.
REPAIR: Please make sure you line up the filter correctly to avoid water leak.
INTSRUCTIONS: 1. Turn the water filter 1/2 turn counterclockwise and pull it down. 2. To install the filter, align the indication mark (unlock position) and push it up while turning turn clockwise until the lock position is aligned. Do not over-tighten. .
Note: If the filter is removed, you will still get water to the icemaker and water dispenser.
SYMPTOM: The Unit is only cycling once and will not cool after that, usually on the Freezer side. However, if you unplug then plug the unit back in it will work again for one cycle. REPAIR: Check Ohm readings on thermal fuse. When fuse is open the Defrost cycle will be inhibited and the unit will not cool again until reset.
Page 41
This bulletin is for the production date before June 2003.The serial no is xxxx43CT6xxxxxx~ xxxx43CW5xxxxxx. From June products to be used Quick ice function. For RS2533SW,2555SW/SL. But not for 2577)
Solution: Initially, have customer run the following test to determine whether problem is operational or if unit needs service. A. Start with empty ice bin and run for 24 hours at the default settings. B. 12 Trays or 120 cubes should be made during this time. If so unit is OK. C. If 50 to 80 cubes are produced during this time frame, instruct to try the test again using a lower temperature or the Power Freeze function. If OK, then problem is the environment and these settings should compensate. D. If less than 50 cubes are produced during the initial 24 hour test, then service call is required. Service technician should run self-diagnostic procedures starting on page 31 of the service manual. Replace listed parts that come up as errors. E. If self-diagnostic yields no clear indication, use the Set Point Shift Function starting on page 34. Lower option 4 on page 36 of service manual icemaker temperature sensor. To speed up the ice making for a old model (before June 2003), please Replace main PCB with yellow label. (RS2533SW:DA41-00134D/ RS2555SW/SL:DA41-00104E). HomePAD is not ready. The Power Freeze (Quick ice) function refer to owners manual and Training manual page 7.
Page 42