User Manual To Mitsubishi Projection TV WS-65315
User Manual To Mitsubishi Projection TV WS-65315
CABLE/DBS TV
VCR
DVD AUDIO
2
5
8
0
POWER
4
7
SQV
9
QV
SLEEP
VIDEO
AUDIO MUTE
INPUT
CHANNEL VOLUME
ENTER EXCH
ADJUST
HOME
CANCEL
MENU
V-CHIP
FORMAT
PIP CH
INFO
GUIDE
REC
STOP
PAUSE
REW/REV
PLAY
FF/FWD
www.mitsubishi-tv.com
RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated dangerous voltage within the products enclosure that may be sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance. Warning: To avoid permanently imprinting a fixed image onto your TV screen, please do not display the same stationary images on the screen for more than 15% of your total TV viewing in one week. Examples of stationary images are letterbox top/bottom bars from DVDs or other video sources, side bars when showing standard TV pictures on widescreen TVs, stock market reports, video game patterns, black or bright Closed Caption backgrounds, station logos, web sites or stationary computer images. Such patterns can unevenly age the picture tubes causing permanent damage to the TV. Please see page 6, 12 or 30 for a detailed explanation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
CAUTION:
CAUTION: To assure continued FCC compliance, the user must use a shielded video interface
cable with bonded ferrite cores at both ends, when using the MonitorLink/DVI input. Changes or modifications not expressly approved by Mitsubishi could void the users authority to operate this equipment.
This TV is very heavy! Exercise extreme care when moving TV as foreign material may become embedded in the castor wheels which could damage wood or other delicate flooring.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION:
Contents
Important Notes ........................................................................................................... 6
Chapter 1
Television Overview
Thank you ..................................................................................................................... 8 Unpacking your New TV............................................................................................... 9 Special Features........................................................................................................... 9 Front Control Panel ..................................................................................................... 10 Back Panel Input/Output............................................................................................. 11 Important Notes .......................................................................................................... 12
Chapter 2
Connections
Connecting an Antenna or Wall Outlet Cable.............................................................. 14 Connecting an Antenna to a Cable Box or VCR.......................................................... 15 Connecting an Antenna to a Cable Box and VCR....................................................... 16 Connecting Audio/Video to the Cable Box or VCR..................................................... 16 Connecting an Audio Receiver.................................................................................... 17 Connecting a DVD Player or Other S-Video Device .................................................... 18 Connecting a DTV Receiver ........................................................................................ 19 Connecting MonitorLink/DVI .................................................................................... 21 How Connections Affect the PIP and POP ................................................................. 22
Chapter 3
Contents
Overview of the TV Layer Buttons............................................................................... 24 Care and Operation ..................................................................................................... 25 Channel Selection ....................................................................................................... 26 Sleep Timer ................................................................................................................ 26 Use With Other A/V Products ..................................................................................... 27 Special Functions ........................................................................................................ 29 Operation of PIP and POP........................................................................................... 29 Important Notes .......................................................................................................... 30
Chapter 4
The ViewPoint Menu System.................................................................................... 32 MAIN Menu ................................................................................................................ 33 SETUP Menu ............................................................................................................... 35 CAPTIONS Menu......................................................................................................... 40 CHANNEL EDIT Menu ................................................................................................. 42 V-CHIP LOCK Menu .................................................................................................... 45 ADVANCED FEATURES Menu .................................................................................... 50 AUDIO/VIDEO SETTINGS Menu ................................................................................. 55
Chapter 5
PIP/POP Operations
Operation of PIP and POP........................................................................................... 60 Available On-Screen Format Sizes ............................................................................ 61 Appendix A: Bypassing the V-Chip Lock .................................................................... 63 Appendix B: HD Input Connection Compatibility........................................................ 65 Appendix C: Remote Control Programming Codes.................................................... 66 Appendix D: Cleaning and Service ............................................................................. 68 Appendix E: Diamond Shield Installation and Removal .......................................... 69 Index ............................................................................................................................ 72 Troubleshooting........................................................................................................... 74 Warranty ...................................................................................................................... 75
Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television.
1. Read, Retain and Follow All Instructions
Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions.
IMPORTANT SAFEGUARDS
2. Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
3. Cleaning
Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners. Cleaners can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.
Important Safeguards
Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash bowls, kitchen sinks, laundry tubs, swimming pools, etc.
6. Accessories
Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting of the TV should follow the manufacturers instructions, and should use mounting accessories recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
7. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturers instructions have been adhered to.
8. Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company.
9. Grounding or Polarization
This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.
13. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
Important Safeguards
16. Servicing
Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
20. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
IMPORTANT NOTES
Warning: Do not leave stationary PIP/POP, or letterbox images on the screen for
extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty.
Examples of these types of images can be, but are not limited to the following: Letterbox top/bottom black bars: Shown at the top and bottom of the TV screen when you watch a widescreen (16:9) movie on a standard (4:3) TV. Side bar images Solid bars shown on each side of an image when watching a standard (4:3) program on a widescreen (16:9) TV. News and stock-market report bars Ticker running at the bottom of the TV screen. Shopping channel logos & pricing displays Bright graphics that are shown constantly or repeatedly in the same location. Video game patterns and scoreboards Bright station logos Moving or low-contrast graphics are less likely to cause uneven aging of the picture tubes. Online (Internet) websites Or any other stationary or repetitive computer style images, including digital photos or computer applications/programs. Closed Captioning Mitsubishi recommends using a gray background rather than a black or a bright color if you frequently use closed captioning.
The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns. Displaying the same stationary patterns over extended periods of time or displaying the same stationary pattern frequently can leave subtle but permanent ghost images. To avoid this, mix your viewing pattern and reduce the initial contrast level. Do not show the same stationary image for more than 15% of your total TV viewing in any given week. Display constantly moving and changing images that fill the screen whenever possible. This projection TV uses picture tubes to project the image to the screen. All picture tubes age with use. As they age, their light output is gradually reduced. Normal TV pictures fill the screen with constantly changing images. Under these conditions, picture tubes age at an even rate across the entire screen. This maintains a TV picture that is evenly bright over the whole screen. Stationary images or images that only partially fill the screen (leaving black or colored bars to fill the screen), when used over extended periods of time or when viewed repeatedly, can cause uneven aging of the phosphors and leave subtle ghosts from the stationary images in the picture. Still or stationary images may be received from broadcasters, cable channels, satellite channels, DVD discs, video tapes, laser discs, on-line services, web/Internet searching devices, video games, digital TV tuner/converter boxes and karaoke machines.
Important Notes
Chapter . . .
Television Overview
Thank you .................................................................................... 8 Unpacking your New TV............................................................. 9 Special Features ......................................................................... 9 Front Control Panel................................................................... 10 Back Panel Input/Output ......................................................... 11 Important Notes ........................................................................ 12
OUR PROMISE
We will engineer and manufacture the upgrades necessary so the HD-upgradeable television you purchased today can be made compatible with near-future advances in digital television and digital interconnectivity. Specifically, we promise that you will be able to have your television upgraded, at a reasonable cost, to include an off-air HDTV tuner, a cable TV tuner (for unscrambled programming), an IEEE 1394 (FireWire) connection, HAVi system control, and 5C copy protection.
Special Features
Your new High Definition (HD) upgradeable bigscreen television has many special features that make it the perfect addition to your home entertainment system. A few of these special features are:
CABLE/DBS/DTV TV
VCR
DVD AUDIO
1
4
2
5
8
0
3
6
9
QV
POWER
7
SQV
SLEEP
VIDEO
AUDIO MUTE
INPUT
CHANNEL VOLUME
Using Picture-in-Picture and Picture-outsidePicture gives you exciting options for viewing favorite programs.
See pages 22, 29 and 62 for more information.
HOME
MENU
V-CHIP
FORMAT
PIP CH
INFO
GUIDE
REC
STOP
PAUSE
REW/REV
PLAY
FF/FWD
With the use of an optional HDTV receiver (Mitsubishi HD-5000 or similar model), your Mitsubishi bigscreen can display high definition pictures.
See page 21 for connection information.
HD Upgradeable
Remote Control
Your Mitsubishi remote control can be programmed to control many other audio/ video components.
See pages 27-28 for more information.
2 AAA Batteries
Mitsubishi understands you may want to shield certain viewers from specific program content. Your Mitsubishi bigscreen will allow you to restrict programming by general contents, specific contents, or even by time.
See pages 45-49 for more information.
V-Chip Technology
16:9 Widescreen TV
Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them. DTV, DVD and newer video game consoles support the widescreen format and are well-suited for your new TV.
See pages 60-61 for more information.
S-VIDEO
VIDEO
L-AUDIO-R
POWER
VOL
CH
INPUT
TIMER
ADJUST
ADJUST
ENTER
MENU
CANCEL
INPUT-3
The ADJUST, ENTER, MENU, and CANCEL buttons may be used to access or navigate through the screen menus
Timer
TIMER
During normal operation, the timer light glows green when the TV is on. It does not glow when the TV is off. When the timer is used to turn the TV on at a specific time, the green timer light blinks while the TV is off. See Timer Menu, page 51 for timer setup instructions.
A/V Reset
A/V RESET
Press this button to reset all A/V memory inputs to the factory default settings. See Audio/Video Settings Menu, page 55 for instructions.
CANCEL
Format
FORMAT
ENTER
Press this button to change the size and shape of the main TV picture.
S-VIDEO
VIDEO
L-AUDIO-R
Input-3
This input can be used for convenient connection of a camcorder or other video device to the TV. You may connect to the S-VIDEO or VIDEO terminal but not to both.
10
5
MONITORLINK RS-232C CONTROL
TM
COMPONE NT
4 80 i / 480P/ 1080i
MONITOR OUT
INPUT 2
Y
2
Y G
S-VIDEO
Pb
Pb B
Pr
Pr
CAUTION:
SERVICE WARNING
AN T - A
LOO P OU T
TO MEASURE SECOND ANODE VOLTAGE USE A HIGH VOLTAGE METER CONNECTED FROM ANODE LEAD TO CHASSIS ONLY. DISCHARGE HIGH VOLTAGE TO CHASSIS ONLY, NOT TO EXTERNAL GROUND.
AN T- B
WARNING:
HANDLE WITH CARE HIGH VACUUM PICTURE TUBE IS DANGEROUS TO HANDLE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. REPLACE WITH A TUBE OF THE SAME TYPE NUMBER FOR CONTINUED SAFETY.
X-RAY PRECAUTION:
THIS PRODUCT INCLUDES CRITICAL MECHANICAL AND ELECTRICAL PARTS WHICH ARE ESSENTIAL FOR X-RADIATION SAFETY. FOR CONTINUED SAFETY REPLACE CRITICAL COMPONENTS INDICATED IN THE SERVICE MANUAL ONLY WITH EXACT REPLACEMENT PARTS GIVEN IN THE PARTS LIST. REFER TO SERVICE MANUAL FOR OPERATING HIGH VOLTAGE AT MINIMUM BRIGHTNESS, MEASUREMENT PROCEDURES AND PROPER SERVICE ADJUSTMENTS.
5. DTV Input
This input is used to connect a DTV receiver or cable box and can be configured for HDTV component (YPbPr), or RGB plus H&V. Please see Appendix B, page 65, for signal compatibility.
6. MonitorLink/DVI
This is a Mitsubishi-exclusive proprietary digital interface for the display of high quality digital video signals from Mitsubishi products such as the HD-5000 HDTV Receiver/Controller. All video signals, both analog and digital are sent digitally to your Mitsubushi TV. Can also be used as a DVI (HDCP) input for other compatible sources. Note: The DVI-HDTV input terminal is compliant with the EIA-861 standard. It is not intended for use with personal computers or devices outputting video signals with computer resolution.
2. Monitor Out
The Monitor Output sends the TV audio and video signals (excluding component video, DTV video and MonitorLink) to an A/V receiver or other equipment.
3. Inputs 1-2
These inputs can be used for the connection of a VCR, Super VHS (S-VHS) VCR, laser disc player, or other A/V device to the TV. With each input, you may connect to the S-VIDEO or VIDEO terminal but not to both.
7. MonitorLink Control/RS-232C
A digital control interface that works in parallel with MonitorLink. While MonitorLink provides the digital video signal, MonitorLink Control provides enhanced functioning such as automatic power ON/OFF and input selection. Can also be used with other compatible RS-232C external control devices. Please visit www.mitsubishi-tv.com for more details.
11
IMPORTANT NOTES
Warning: Do not leave stationary PIP/POP, or letterbox images on the screen for
extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty.
The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns. Displaying the same stationary patterns over extended periods of time or displaying the same stationary pattern frequently can leave subtle but permanent ghost images. To avoid this, mix your viewing pattern and reduce the initial contrast level. Do not show the same stationary image for more than 15% of your total TV viewing in any given week. Display constantly moving and changing images that fill the screen whenever possible. This projection TV uses picture tubes to project the image to the screen. All picture tubes age with use. As they age, their light output is gradually reduced. Normal TV pictures fill the screen with constantly changing images. Under these conditions, picture tubes age at an even rate across the entire screen. This maintains a TV picture that is evenly bright over the whole screen. Stationary images or images that only partially fill the screen (leaving black or colored bars to fill the screen), when used over extended periods of time or when viewed repeatedly, can cause uneven aging of the phosphors and leave subtle ghosts from the stationary images in the picture. Still or stationary images may be received from broadcasters, cable channels, satellite channels, DVD discs, video tapes, laser discs, on-line services, web/Internet searching devices, video games, digital TV tuner/converter boxes and karaoke machines.
Examples of these types of images can be, but are not limited to the following: Letterbox top/bottom black bars Shown at the top and bottom of the TV screen when you watch a widescreen (16:9) movie on a standard (4:3) TV. Side bar images Solid bars shown on each side of an image when watching a standard (4:3) program on a widescreen (16:9) TV. News and stock-market report bars Ticker running at the bottom of the TV screen. Shopping channel logos & pricing displays Bright graphics that are shown constantly or repeatedly in the same location. Video game patterns and scoreboards Bright station logos Moving or low-contrast graphics are less likely to cause uneven aging of the picture tubes. Online (Internet) websites Or any other stationary or repetitive computer style images, including digital photos or computer applications/programs. Closed Captioning Mitsubishi recommends using a gray background rather than a black or a bright color if you frequently use closed captioning.
Important Notes
12
Chapter . . .
Connections
Connecting an Antenna or Wall Outlet Cable ............................ 14 Connecting an Antenna to a Cable Box or VCR ........................ 15 Connecting an Antenna to a Cable Box and VCR...................... 16 Connecting Audio/Video to a Cable Box or VCR....................... 16 Connecting an Audio Receiver .................................................... 17 Connecting a DVD Player or Other S-Video Device .................. 18 Connecting a DTV Receiver ......................................................... 19 Connecting MonitorLink/DVI.................................................... 21 How Connections Affect the PIP and POP.................................. 22
Additional connection cables are not provided with the TV. They should be available at most electronic stores.
(Figure 1)
1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-A on the TV back panel.
UHF/VHF combiners are not provided with the TV. They are available at most electronic stores.
Note: This TV will only be able to provide an analog signal through ANT-A on the TV back panel. See page 5 for Outdoor Antenna Grounding information.
Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable.
For antenna with twin flat leads: 1. Connect the 300 Ohm twin leads to the transformer. 2. Push the 75 Ohm side of the transformer onto ANT-A on the TV back panel.
300 Ohm to 75 Ohm matching transformers are not provided with the TV. They are available at most electronic stores.
Figure 2. Connecting twin lead antenna, coaxial lead antenna, or wall outlet cable.
For cable or antenna with coaxial lead: 3. Connect the incoming cable to ANT-A on the TV back panel.
Note: This TV will only be able to provide an analog signal through ANT-A on the TV back panel.
Additional connection cables are not provided with the TV. They should be available at most electronic stores.
14
Cable Box
(Figure 3)
1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the cable box back panel. 3. One from OUT on the cable box back panel to ANT-B on the TV back panel. Note: If your cable box has separate audio/video outputs, please see Composite Video with Audio or S-Video with Audio, page 16 (Figure 6).
1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR back panel. 3. One from VCR back panel ANTENNA OUT to ANT-B on the TV back panel. Note: If your cable box has separate audio/ video outputs, please see Composite Video with Audio or S-Video with Audio, page 16 (Figure 6).
Note: For models WS-48315, WS-55315, WS-65315 and WS-65315A, when the Energy Mode is set to Low, the VCR may not record programs when the TV is off.
Note: For digital cable boxes, refer to your Digital Cable Box owners guide for instructions on optimal connections to this TV.
15
Connecting an Antenna to a Cable Box and VCR, Connecting Audio/Video to the Cable Box or VCR
Note: The TV back panel and connections shown here are for reference only and may vary by model.
Contact your local cable or satellite provider or refer to the cable box or satellite Owners Guide for instructions on optimal connections to this TV.
Cable Box
(Figure 5)
Connecting an Antenna to a Cable Box and VCR Connecting Audio/Video to the Cable Box or VCR
1. Connect the incoming cable to ANT-A on the TV back panel. Connect three coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the back of the cable box. 3. One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel. 4. One from ANTENNA OUT on the VCR back panel to ANT-B on the TV back panel.
Note: For best performance, please see Composite Video with Audio or S-Video with Audio, below.
Additional connection cables are not provided with the TV. They should be available at most electronic stores.
1. Connect a video or an S-Video cable from VIDEO OUT on the VCR back panel to VIDEO or S-VIDEO, INPUT-1 or INPUT-2 on the TV back panel. 2. Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT-1 or INPUT-2 on the TV back panel, matching the input used in step 1.
The red cable connects to the R (right) channel The white cable connects to the L (left) channel
If your VCR is mono (non-stereo), connect only the white (left) cable. You may connect to the S-VIDEO or VIDEO terminal but not to both.
16
1. Connect the audio cables from AUDIO MONITOR OUTPUT on the TV back panel to TV IN or AUX IN terminals on the back of the audio system.
The red cable connects to the R (right) channel The white cable connects to the L (left) channel
2. Turn off the TVs speakers through the AUDIO/ VIDEO SETTINGS Menu, page 55. 3. Set the audio systems input to the TV or AUX position to hear the TVs audio through your stereo system.
These types of audio connections do NOT support multi-channel digital audio. Please refer to your other devices Owners Guide to verify.
A/V Receiver
1. Connect either a video cable or an S-Video cable (but not both) from VIDEO MONITOR OUT on the back of the A/V receiver to VIDEO INPUT1 or INPUT-2 on the TV back panel. Note: If the A/V receiver outputs an onscreen menu, this connection allows you to view the receivers menu on the television. 2. Connect a video cable from VIDEO MONITOR OUTPUT on the TV back panel to VIDEO TV IN on the back of the A/V receiver. 3. Connect a set of audio cables from AUDIO MONITOR OUTPUT on the TV back panel to AUDIO TV IN on the back of the A/V receiver.
The red cable connects to the R (right) channel The white cable connects to the L (left) channel
(Figure 8)
Note: Please see your A/V receiver Owners Guide for more detailed connections.
17
1. Connect the Component Video cables from (Y Cb Cr or Y Pb Pr) VIDEO OUT on the back of the DVD player to COMPONENT (1 or 2) on the TV back panel. The correct connections are: A. Y to Y B. Cb or Pb to Pb
(Figure 9)
C. Cr or Pr to Pr 2. Connect a set of audio cables from AUDIO OUT on the back of the DVD player to COMPONENT AUDIO Input (1 or 2) on the TV back panel.
The red cable connects to the R (right)channel The white cable connects to the L (left) channel
See Appendix, page 65, for component video signal compatibility information. For digital audio connections, see your DVD and A/V receiver Owners Guides.
Note: Some video game systems support DTV resolutions via component connections. Please refer to your video game console Owners Guide for setup information. Note: For optimal DVD playback performance, Mitsubishi recommends using a progressive scan DVD player, set to play in progressive scan mode. You will also want to set your player to display 16:9 widescreen. Please refer to your DVD players Owners Guide.
1. Connect an S-Video cable from VIDEO OUT on the device back panel to VIDEO INPUT-1 or INPUT-2 on the TV back panel. 2. Connect a set of audio cables from AUDIO OUT on the device back panel to AUDIO INPUT-1 or INPUT-2 on the TV back panel, matching the input used in step 1.
The red cable connects to the R (right) channel
(Figure 10)
If your S-Video Device is mono (non-stereo), connect only the white (left) cable.
18
Note: The TV back panel and connections shown here are for reference only and may vary by model. Contact your local cable or satellite provider or refer to the cable box or satellite Owners Guide for instructions on optimal connections to this TV.
(Figure 11)
The TV back panel has 5 RCA-type connectors for the DTV connection. The back panel of your DTV receiver may use RCA-type connectors or BNCtype connectors. If your DTV receiver comes with BNC type connections, you will need to purchase BNC to RCA adaptors to connect the TV to the DTV receiver. These adaptors should be available at most electronic supply stores.
or
BNC to RCA Adaptor BNC Connector Adaptor Fitted to Connection
RCA Connector
See Appendix, page 65, for component video signal compatibility information.
For digital audio connections, see your DTV and A/V receiver Owners Guides.
Figure 12. Connecting the DTV receiver with component Video Connections.
19
Note: The TV back panel and connections shown here are for reference only and may vary by model.
(Figure 13)
2. If your DTV receiver has a built-in terrestrial tuner, connect the incoming terrestrial antenna to ANT on the DTV receiver. If your DTV receiver does not have a built-in terrestrial tuner, this TV will only be able to provide an analog signal through Ant-A on the TV back panel.
Figure 13. Connecting the DTV receiver with RGB video connections.
3. Connect the RGB cables from the DTV receiver to the TV back panel as listed below (if your DTV receiver uses BNC-type cables, use the adaptors shown in Figure 11, page 19): DTV Receiver TV Back Panel
See Appendix, page 65, for component video signal compatibility information. For digital audio connections, see your DTV and A/V receiver Owners Guides.
= = =
4. If the DTV receiver has outputs for H and V sync, connect as listed below ( DO NOT connect if DTV receiver uses Sync on Green):
H V
5. Connect the L (left) and R (right) audio cables from the DTV receiver to DTV AUDIO on the TV back panel. 6. To utilize the benefits of a digital A/V receiver, connect your DTV receivers digital audio out to a digital input on your digital A/V receiver. You may need to setup the DTV (See Input Assignment, page 35) to RGB.
20
Connecting MonitorLink/DVI
MonitorLink/DVI
WS-48315, WS-55315, WS-65315, WS-65315A back panel (section detail)
DTV( Y PbPr/ GBRH V )
480 i / 480P /1080 i
Y G
MONITORLINK /DVI
TM
ferrite core
(Figure 14)
The Monitor Link/DVI input uses a DVI-I Dual Link connector for maximum cable flexibility. When MonitorLink is used as a DVI-HDCP input, the terminal is compliant with DVI-D Single Link signals matching EIA-861 standards for standard, extended and high definition video with scanning rates of 480p and 1080i. However, this input is not intended for use with personal computers or devices outputting video signals with computer resolutions. All other DTV video signals, such as 720p, need to be converted by the DTV receiver (or compatible device) to one of the compatible signal types. Please check the specifications on your device before connecting. 1. Connect a MonitorLink/DVI cable from the TV back panel to the Mitsubishi HD Receiver/ Controller back panel. 2. Connect the MonitorLink Control/RS-232 cable from the TV back panel to the Mitsubishi HD Receiver/Controller back panel. 3. Connect the L (left) and R (right) audio cables from the HDTV receiver to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel. Note: DVI and RS-232 cables can be found at your local electronics store if they are not included with your devices. Please refer to www.mitsubishi-tv.com for more information on RS-232C control.
TM
403XF-5K
Pb
Pr R
White
Red
INPUT 1 2 3 4
TO AV RECEIVER
MONITOR PIP
TO DISPLAY
S-VIDEO
Connecting MonitorLink/DVI
White
AC IN
MonitorLink /DVI
TM
Red
403XF-5K
2
ferrite core
This connection supports copy protection (HDCP). Some devices require connecting to an analog input first, in order to view on-screen menus and select DVI as the output. Please review your equipment instructions for DVI connectivity and compatibility.
CAUTION: To assure continued FCC compliance, we recommend using a shielded video interface cable with bonded ferrite cores at each end, when using the MonitorLink/DVI input.
21
PIP/POP Main Ant-A Ant-B DTV 480i, 480p, 1080i Input-1 Input-2 Input-3 Component(s) (Comp-1, -2 ) 480i, 480p, 1080i MonLink/DVI
Ant-A
Ant-B
OK* OK OK OK
No PIP/POP OK* OK OK
OK
OK
OK
OK
OK**
OK
OK
OK
OK
OK
* No Side-by-Side with the same channel **No Side-by-Side with the same input Component-2 is not available on the WT-42315
22
Chapter . . .
1. Slide Switch: Select A/V product to be controlled by the remote control. 2. Numbers: Individually select channels or input information into TV. 3. POWER: Turns power on and off for TV and other connected A/V products. 4. SQV (Super Quick View): Scan through a memorized list of favorite channels. 5. QV (Quick View): Switch to last channel viewed. 6. SLEEP: Set the TV to turn off within 2 hours. See Sleep Timer, page 26, for setup instructions. 7. INPUT: Select the signal to view; Ant-A, Ant-B, DTV, Component-1, Component-2, Input-1, Input-2, Input-3 or MonLink (Component-2 not available on WT-42315). 8. CHANNEL: Scroll up or down through memorized channels. Skips DVD chapters in DVD layer. 9. VOLUME: Change sound level. 10. VIDEO: Select the individual video settings. 11. AUDIO: Select the individual audio settings. 12. MUTE: Turn sound on or off. 13. ENTER/EXCH: Select a channel number or menu item. Exchange PIP or POP with the main TV picture. 14. ADJUST: Navigate menus, change settings, and move the PIP on-screen location. 15. HOME: Exit on-screen menus and return to TV viewing. 16. CANCEL: Clear SQV and some menu entries. Used as a subchannel button in Cable/DBS/ DTV layer. 17. MENU: Display system. on-screen menu
24
18. V-CHIP: Displays V-Chip Passcode screen, use to enable or disable the V-Chip Lock.
1. Remove the remote controls back cover by gently pressing the ridged tab in the direction of the arrow and sliding off the cover. 2. Load the batteries, making sure the polarities (+) and (-) are correct. For ease of installation, install the negative (-) side first.
CABLE/DBS/DTV TV
VCR
DVD AUDIO
2 1
4
7
SQV
2
5
8
0
POWER
9
QV
SLEEP
INPUT
CHANNEL VOLUME
VIDEO
10
AUDIO
11
MUTE
For Best Results from the Remote Control: Be within 20 feet of the equipment. Do not press two or more buttons at the same time unless instructed to. Do not allow to get wet or become heated. Avoid dropping on hard surfaces. Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth. Do not mix new and old batteries. Do not heat, take apart, or throw batteries into fire. Use only AAA batteries.
12
31
13
HOME
ADJUST
14
15
MENU
16
V-CHIP
17
18
PIP INPUT
PIP CH
INFO
19
FORMAT
22
REC
PIP/POP
20
21
GUIDE
23
24
STOP
PAUSE
25 28
REW/REV
26 29
PLAY
27 30
FF/FWD
You can use the remote to control the TV, CABLE/ DBS/DTV, VCR, DVD, and AUDIO products. Select the product you want to control by moving the slide switch to the appropriate position. The remote control has been preset to operate the TV and other Mitsubishi products. To program the remote control to operate other products, see Use of the Remote Control with Other A/V Products, page 27.
Figure 2. Installing the batteries.
The remote control may return to its initial setting when the batteries are changed. It may need to be reprogrammed.
AAA
AAA
25
CABLE/DBS/DTV TV
VCR
DVD AUDIO
or Press the channel number and ENTER (ex. for channel 2, press 2, then ENTER). or
1 4 7
SQV
2 5 8 0
3 6 9
QV
POWER
SLEEP
Enter the channel number and wait four seconds (without pressing ENTER). The TV will change automatically. Note: Use the CANCEL button for digital subchannel (-) selection in the CABLE/DBS/DTV layer.
(Figure 3 & 4)
Sleep Timer
Setting the Sleep Timer: Press SLEEP on the remote control. A message indicating the length of time the sleep timer is to be set appears on the TV screen. Each press of SLEEP will increase the time displayed by 30 minutes, until the maximum value of 120 minutes is reached. After 5 seconds of inactivity, the message will disappear. Press SLEEP to view the remaining time before the timer turns the TV off.
Sleep: 30 min.
Canceling the Sleep Timer: Press the SLEEP button to display the on-screen message. Press SLEEP repeatedly until OFF is displayed. After 5 seconds of inactivity, the message will disappear.
26
1. Move the slide switch at the top of the remote to the product you want to control.
2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control to the equipment and press the POWER button. Note: If the equipment responds,the remote control is properly programmed to operate the equipment. If the equipment does not respond, repeat steps 2-4 with the next three digit code listed in step 3.
CABLE/DBS/DTV VCR DVD AUDIO TV CABLE/DBS/DTV VCR DVD AUDIO TV
1. 3.
2.
Cable Box Codes
Code to enter: 119, 120, 121, 122,123, 124 125, 126, 127 139, 137, 102 101, 116 112, 113 117, 100
POWER
Cable box brand General Instruments/ Jerrold Motorola Oak Pioneer Scientific Atlanta Zenith
If your cable box code is not listed here, please see page 66 for a complete listing.
1. 3.
2.
VCR Codes
VCR brand Mitsubishi Hitachi JVC Phillips / Magnavox Panasonic RCA Sony Toshiba
POWER
Code to enter: 001, 002 020, 043, 065 030, 054 043, 044, 051 041, 042, 043 020, 053, 065 048, 049, 050 021
If your VCR code is not listed here, please see page 67 for a complete listing.
If you cannot turn the cable box ON by pressing POWER, try pressing CHANNEL or the number buttons.
When set to TV, the PLAY, STOP, REW/ REV, and FF/FWD buttons will operate the VCR after the VCR codes have been properly programmed into the remote control.
CABLE/DBS/DTV VCR DVD AUDIO TV
POWER
Code to enter: 006 175 173 174 176 177 170, 173, 189, 190, 191
If your satellite receiver code is not listed here, please see page 67 for a complete listing.
1. 3. DVD/LDP brand
Mitsubishi JVC Panasonic Philips Pioneer DVD Samsung Sony Toshiba
2.
DVD Player Codes
Code to enter: 003 257 250 258, 253, 272 252 261 254 253
POWER
If your DVD code is not listed here, please see page 66 for a complete listing.
27
1. 3. Audio brand
2. POWER
If your audio code is not listed here, please see page 66 for a complete listing.
Code to enter: Mitsubishi A/V receiver 010, 015, 011, 012, and/or CD player 013, 014 234, 235, 236, 245, Denon 246, 359 Harman Kardon 215, 223, 242 JVC 233, 232 Kenwood 208, 200 Marantz 224, 350 Onkyo 209, 214, 240, 247 Pioneer 205, 207 Sony 222, 249 Technics 218, 219, 221 Yamaha 202, 201, 243, 244
After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed. If you enter a code from the AUDIO chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V receiver with the TV all the time. In all other cases, only one of the below devices is allowed for each slide switch position. TV position: TV A/V receiver (volume and mute only) Cable/DBS/DTV position: Cable box Satellite receiver
If the slide switch is set to TV when you enter an A/V receiver code, VOLUME and MUTE will control the A/V receiver rather than the TV. To return volume and mute control to the TV, set the slide switch to TV, press and hold POWER and enter 000.
DTV receiver VCR position: VCR DVD position: DVD LD Player Audio position: A/V receiver
Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, your remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver.
Mitsubishi CD player If you have a Mitsubishi A/V receiver, the audio position may be used in conjunction with select Mitsubishi CD players. Your audio position must be programmed to either 010 or 011. Plug the CD player power cord into a switched outlet on the back of your A/V receiver. Pressing the POWER button turns On the A/V receiver, along with the CD player. In the audio position, for some CD players, the transport controls (FF, Play, Rew, etc.) operate the CD player.
28
Press PIP/POP to choose a display format. Each time the PIP/POP button is pressed on the TV remote control (within 3 seconds of each other), the PIP/POP cycles through the following display options.
1. POP: side-by-side pictures 2. POP: three POPs 3. POP: nine POPs 4. PIP: large PIP 5. PIP: small PIP To turn PIP/POP Off, wait at least 10 seconds, and press PIP/POP. The next time you activate PIP/POP, the last used PIP/POP format will be displayed first.
A/V Receivers
Direct Input Selection buttons: numbers, SQV and QV (on some models)
DVD and Laser Disc Players ( not all functions for all models)
POWER MENU 0-9 number buttons (on some models) PLAY STOP ARROW up/down/left/right (on some models) FF/FWD REW/REV PAUSE CANCEL (on some models) ENTER CHANNEL (on some models)
29
IMPORTANT NOTES
Warning: Do not leave stationary PIP/POP, or letterbox images on the screen for
extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty.
The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns. Displaying the same stationary patterns over extended periods of time or displaying the same stationary pattern frequently can leave subtle but permanent ghost images. To avoid this, mix your viewing pattern and reduce the initial contrast level. Do not show the same stationary image for more than 15% of your total TV viewing in any given week. Display constantly moving and changing images that fill the screen whenever possible. This projection TV uses picture tubes to project the image to the screen. All picture tubes age with use. As they age, their light output is gradually reduced. Normal TV pictures fill the screen with constantly changing images. Under these conditions, picture tubes age at an even rate across the entire screen. This maintains a TV picture that is evenly bright over the whole screen. Stationary images or images that only partially fill the screen (leaving black or colored bars to fill the screen), when used over extended periods of time or when viewed repeatedly, can cause uneven aging of the phosphors and leave subtle ghosts from the stationary images in the picture. Still or stationary images may be received from broadcasters, cable channels, satellite channels, DVD discs, video tapes, laser discs, on-line services, web/Internet searching devices, video games, digital TV tuner/converter boxes and karaoke machines.
Examples of these types of images can be, but are not limited to the following: Letterbox top/bottom black bars Shown at the top and bottom of the TV screen when you watch a widescreen (16:9) movie on a standard (4:3) TV. Side bar images Solid bars shown on each side of an image when watching a standard (4:3) program on a widescreen (16:9) TV. News and stock-market report bars Ticker running at the bottom of the TV screen. Shopping channel logos & pricing displays Bright graphics that are shown constantly or repeatedly in the same location. Video game patterns and scoreboards Bright station logos Moving or low-contrast graphics are less likely to cause uneven aging of the picture tubes. Online (Internet) websites Or any other stationary or repetitive computer style images, including digital photos or computer applications/programs.
IMPORTANT NOTES
Closed Captioning Mitsubishi recommends using a gray background rather than a black or a bright color if you frequently use closed captioning.
30
Chapter . . .
not display the same stationary images on the screen for more WARNING: Do than 15% of your total TV viewing in one week. Examples of stationary images are letterbox top/bottom bars from DVD or other video sources, side bars when showing standard TV pictures on widescreen TVs, news and stock market reports, video game patterns, station logos, black or bright closed caption backgrounds, web sites, or stationary computer images. Such patterns can unevenly age the picture tubes causing permanent damage to the TV. Please see pages 6, 12 or 30 for a more detailed explanation.
The
Menu System
on-screen operating system provides on-screen information for menu
A picture (icon) will be highlighted and can be selected using the remote controls ADJUST arrows. When selected, the appropiate menu will appear or start an automatic function. You may then make changes within the menu or access available submenus.
The following remote control buttons allow you to move quickly through the system (Figure 2) : ADJUST or to select the menu item you want to change. ADJUST ADJUST ADJUST to move to the setting field. or to change the settings.
Menu System
A highlighted square button indicates that you may make changes to the menu screen. The features: system includes the following special
ENTER to enter into a menu, start an automatic function, or select a checkbox. CANCEL to clear a setting, or stop an automatic function. MENU to move back one menu screen at a time. HOME to exit all menus at once and return to TV viewing.
The currently selected icon or button is highlighted with a rectangular yellow outline and the text color will be yellow. On-screen instructions provide complete menu choice information. Some on-screen menu options must be set before other options are available. For example, Timer Menu will only be possible if Clock Time and Set Day have been set.
ENTER EXCH
ADJUST
HOME
The
CANCEL
MENU
INFO
V-CHIP
PIP CH
FORMAT
GUIDE
Figure 2. Remote control buttons used for navigation within the on-screen operating system.
Figure 1. MAIN menu: The first screen to appear when you press MENU button on the remote.
Note: Mitsubishi recommends becoming familiar with the Convergence Menu (pages 53-54) during initial setup. It may be necessary to periodically use this menu throughout the lifetime of this product for optimal picture performance.
32
(Figure 3)
SETUP Menu
Basic (initial) setup instructions and functions are available through the SETUP submenu screens. Use this menu when you relocate the TV, experience a power loss or when devices are added after initial setup. Memorize channels
Select English or Spanish for the menus or screen display Set the Front Button Lock (WT-42315) Set the Energy Mode (WS-48315, WS-55315, WS-65315 or WS-65315A).
CAPTIONS Menu
(Figure 4)
Display broadcast captions or text on the screen. Select the settings by choosing to display the background color as either black or translucent gray. See pages 40-41 for detailed setup information.
Note: Mitsubishi recommends using a translucent gray background to prevent CRT aging and/or burn-in.
Customize the channel information for Ant-A and Ant-B, Manually add or delete channels from memory Name channels for Ant-A and Ant-B Add your favorite channels to a SQV (Super Quick View) list.
33
Lock the TV by selecting times or choosing programs to block based on rating signals sent by your local broadcasting system. Note: For WS-48315, WS-55315, WS-65315 or WS-65315A set the Front Button Lock at this screen. See pages 46-49 for detailed setup information. See page 45 for V-Chip rating information.
Adjust colors automatically or manually, using Color Balance Set your TV to turn on automatically Converge (align) the three main colors Display a blue screen when viewing an input with no signal Enhance the darker parts of bright pictures See pages 50-54 for detailed setup information.
Adjust some or all of the A/V settings. Each input can be set to your preferences. A/V Reset on the menu allows you to return the A/V settings for the current input to the factory presets. A/V Reset on the front control panel resets all inputs at one time. See pages 55-57 for detailed setup information.
34
(Figure 9)
Memorize Channels
Select Memorize Channels for each antenna you use. The TV will find and remember strong channels and skip the unused or weaker channels.
DTV Note: If you have a DTV receiver connected, you will need to use that receivers channel memorization system to memorize digital channels.
(Figure 10)
MEMORIZE Menu
Stop memorization at any time by pressing CANCEL. Channels memorized prior to pressing CANCEL will stay in memory. After channels are memorized, you may select memorized channels in ascending or descending order by pressing the CHANNEL button on the remote control.
(Figure 11)
INPUT ASSIGNMENT turns off unused inputs, turns them on again or changes the name of the input. If you turn an input Off, it will be skipped when you press INPUT on the remote control. Choices are: ANT-A, ANT-B: On or Off
DTV: Y/Pb/Pr, RGB, RGBHV or Off COMPONENT(S)* Cycle through a list of preset names or Off
INPUT-1, INPUT-2, INPUT-3: Cycle through a list of preset names or Off MonitorLink (MONLINK) Cycle through a list of preset names or Off * COMPONENT-2 is not available for WT-42315.
35
The Clock Setting menu default allows the clock time to be set manually. To set the clock automatically, please see page 37. To set the clock manually, first select the current time, including AM or PM. Press or to slowly adjust the time. Press and hold or to quickly adjust the time.
(Figure 13)
Set Day
After manually selecting the current time, select the current day.
36
Set the Clock Setting to Auto to automatically set the day and time using Extended Data Service (XDS) time data. This data is automatically retrieved when tuned to a PBS channel or other channel in your area that provides this service.
Time Zone
(Figure 15)
Select the correct time zone (Atlantic, Eastern, Central, Mountain, Pacific, Alaska, or Hawaii) for your area when Auto has been selected as the Clock Setting.
(Figure 16)
Select the Daylight Savings Time (DST) option that your state uses when Auto has been selected for the Clock Setting. Applies = uses DST Ignore = does not use DST The clock time and day will be set automatically after tuning to a channel carrying the Extended Data Service (XDS) time data (usually your local PBS channel).
37
(Figure 17)
Language
Display the on-screen menus in either English or Spanish (Espaol). The first time you powered On your TV, you were requested to select an on-screen menu language. If you choose to change the selection, all menu text will immediately switch to the language of your choice.
If the front panel buttons have been locked and you misplace the remote control, you can restore the function of the front panel buttons by pressing and holding the MENU button on the front panel for more than 8 seconds. If the TV is already on, a message will be displayed to confirm the release of the Front Button Lock.
38
WS-65315A)
SETUP Menu: Energy Mode (WS-48315, WS-55315, WS-65315, SETUP Menu: Energy Mode (WS-48315, WS-55315, WS-65315,
Energy Mode
(Figure 19)
This feature is only for models WS-48315, WS-55315, WS-65315 and WS-65315A. Change the setting to Low (less than 1 watt) and the TV will operate in an energy saving mode when it is turned off. If the Energy Mode is set to Low, it will not be possible to record while the TVs power is off. There will be no signal from LOOP OUT (on the TV back panel) to the VCR and/or cable box.
WS-65315A)
Note: The Standard setting has a faster turn on time, but uses more power than the Low setting. Standard is recommended.
39
CAPTIONS Menu
(Figure 20)
Turn On or Off the closed caption decoder, select the type of captions or text, and choose black or translucent gray as the background color for the closed caption area. Broadcasters can send either Standard or Text closed captioning. Standard closed captioning follows the dialogue of the characters on-screen and displays in a small section of the screen.
Text closed captioning often contains information such as weather or news and covers a large portion of the on-screen program. Your TV can decode four different standard and four different text closed captioning signals from each TV station. However, each TV station may broadcast only one or two closed captioning signals, or none at all.
When Text closed captioning is selected, a large black or gray box will appear on your TV screen if no signal is broadcast.
40
Display one of the following types of Closed Captions: CC1, CC2, CC3, or CC4: Standard closed captioning signals. Text1, Text2, Text3, or Text4: Text closed captioning signals. On if mute: Closed captions when mute. When selected, the standard closed captioning signal (CC1) will turn on/off by pressing the MUTE button on the TV remote control. Off: No closed captions.
The content of captions is determined by the broadcaster. If your captions show strange characters, misspellings, or odd grammar, it is not a malfunction of the TV.
CC Background
(Figure 22)
Display the background color as either black or translucent gray, to make the closed captions easier to read.
Mitsubishi recommends using the translucent gray background to prevent CRT aging and/or burn-in.
41
Antenna
(Figure 23)
Select Ant-A or Ant-B. For each antenna, you can add or delete channels in memory, name channels, and add channels to the SQV (Super Quick View) list.
Channel
(Figure 24)
Select to edit the channel selections. You can add or delete from memory, name, or add to the SQV (Super Quick View) list. After selecting Channel, editing can be done using the Adjust buttons or entering the 3 digit channel number you want to change (Example 002 for channel 2).
42
(Figure 25)
Add weaker channels viewed with Ant-A or Ant-B and delete unwanted channels, after all available channels have been memorized with Memorize Channels (page 35). Use the CHANNEL button on the remote control to view memorized channels.
(Figure 26)
Name
Name channels shown on Ant-A or Ant-B (up to four characters). After you enter a name, it will appear on the TV screen next to the channel number. 1. Select Ant-A or Ant-B. 2. Select the memorized channel you want to name. 3. Press ADJUST until you see the underline highlighted in the Name field. 4. Use ADJUST or to select letters A-Z, numbers 0-9, and/or symbols (!.&/:*- and blank) for each character of the name you would like for the selected channel. Press ENTER after choosing each letter and after the name is complete. If you want to change your selection while on the option field, use CANCEL to delete the current character. You will move one position back. If you press CANCEL while at the first character, the entire name will be deleted.
43
Put together a list of your favorite channels from Ant-A and Ant-B using SQV (Super Quick View). Store up to 6 channels in each of the 9 different memory banks. After adding a channel to the SQV memory, SQV will appear under the channel number on the TV screen. To change SQV choices using the menu: 1. Press or when at Channel settings or use the CHANNEL button on the remote control to select the channel you wish to add or delete from a SQV memory bank. 2. Press when at SQV in the menu to move the selector to the On/Off setting. 3. Press or when at SQV setting to select the SQV memory bank you wish to modify. 4. Press ENTER to add (On) or delete (Off) the current channel from the SQV memory bank that you have selected.
View and add SQV channels using the remote control: 1. Use the CHANNEL or number buttons to select the channel you want to add. 2. Press and hold the SQV button for about 3 seconds. When SQV and the memory bank number appear under the channel number, the channel has successfully been added. To change the SQV banks using the remote control: 1. Press the SQV button. 2. To change memory banks, press a number button within 5 seconds of pressing the SQV button. Remove SQV channels using the remote control: 1. Press the SQV button repeatedly until you see the desired channel. 2. While the channel number and SQV indicator are still displayed on the screen, press CANCEL. If CANCEL is not pressed before the SQV indicator disappears, the channel will not be removed. When the SQV indicator disappears, the channel has successfully been removed.
44
V-CHIP EXCEPTIONS:
1. V-Chip is effective only for programs viewed on Ant-A, Ant-B, or from devices connected to Inputs 1-3. It is not effective for programs viewed on devices connected to Component Input or MonitorLink. 2. Videotapes, laser discs and DVDs may not contain V-Chip rating signals. If they dont contain the V-Chip signal, V-Chip cannot block the program or movie. 3. Broadcasters are not currently required to include V-Chip rating signals at this time. If the broadcaster does not include the V-Chip rating signal, V-Chip cannot block the program.
TV Ratings:
Used with TV programs and Made-for-TV movies. TV-Y Youth, for children under the age of 7. TV-Y7 Youth, 7 years old and older. For children 7 years old and older. TV-G General Audience. For the entire family to view. TV-PG Parental Guidance. Parental Guidance is recommended, may not be suitable for some children. TV-14 Adolescent 14 years old and older. Not recommended for children under the age of 14. TV-MA Mature Audience. For adults only.
FV X
X X
X X X
X X X
X X X
Content Categories:
Used in association with the TV ratings above. FV Fantasy Violence- applies to TV-Y7 only. D Sexual Dialog- applies in different degrees to TV-PG and TV-14. L Adult Language-applies in different degrees to TV-PG, TV-14, and TV-MA. S Sexual Situations- applies in different degrees to TV-PG, TV-14, and TV-MA V Violence (graphic or realistic)- applies in different degrees to TV-PG, TV-14, and TV-MA.
When you select a TV rating, you are selecting the least-restricted program level that can be viewed. As an example, if you select TV-PG, you are allowing programs rated TV-Y, TV-Y7, TV-G and TV-PG to be seen and blocking programs rated TV-14 and TV-MA. When you select a TV Content category, you will block all TV programs that have the same content category listing. As an example, if you select to block V (Violence) at the TV-14 level, you will also block any program that has the V category listing at the TV-PG rating level as well. Used with theater released movies and direct-to-video movies. G General Audience- Designed for the entire family to view. PG Parental Guidance- Parental Guidance is recommended, may not be suitable for some children. PG-13 Parental Guidance 13 years old and older- Not recommended for children under the age of 13. R Restricted- Restricted in the theater to 17 years old and older unless accompanied by an adult. NC-17 No Children- Restricted in the theater to 18 years old and older. X Adult- Designed for and restricted in the theater to adult audiences only. When you select a Movie rating, you are selecting the least restricted program level that can be viewed. As an example, if you select a movie rating of PG-13, you are allowing movies rated G, PG and PG-13 to be seen and blocking movies rated R, NC-17, and X.
Movie Ratings:
Programs Not Rated: Used for programs that are not rated like news, sports, weather, emergency bulletins, or movies such as those prior to or without MPAA Ratings. This does not include programs without V-Chip signals.
If you select to block programs that carry the V-Chip rating Programs Not Rated, you may block News or Emergency Bulletins, when None or NR (Not Rated) V-Chip rating is included. Care should be used when blocking programming that is not rated.
45
V-CHIP Menu: Setting Up and Using V-Chip Lock Passcode V-CHIP Menu: Setting Up and Using V-Chip Lock Passcode
Select V-CHIP LOCK from the MAIN menu for first time setup or after you have canceled your passcode. You will see the screen shown in Figure 29. Use the number buttons on the remote control to input a new four-digit passcode, then press ENTER. Before pressing ENTER, you can delete a character and move back one character by pressing CANCEL, or leave the passcode screen by pressing MENU or HOME.
Figure 29. First time entry to the V-CHIP LOCK all models
Input your passcode as shown in Figure 30 (Note: Text changes from a new to your passcode). The next time you select V-CHIP LOCK from the MAIN menu, you will see this screen.
46
Block or Allow programs based upon rating signals sent by the broadcasting station. The factory preset for TV Ratings is TV-PG (Parental Guidance) allowing only programs rated TV-PG or lower. The factory preset for Movies is PG, allowing only movies rated PG or lower. Please refer to page 45 for a detailed ratings description.
V-CHIP HOURS/LOCK BY TIME will allow you to activate the V-Chip or lock the entire TV during specific hours.
Select the times you would like the V-Chip to be Active. By setting the V-Chip Start Time and VChip Stop Time to the same time, the V-Chip will be active 24 hours a day. Press or to slowly adjust the time. Press and hold or to quickly adjust the time.
Lock by Time locks the entire TV when Lock by Time is On and you have selected a Lock Time and Unlock Time. Your TV continues to be locked until you input your passcode, or when the locked time expires.
47
LOCK by Time
(Figure 33)
V-CHIP Menu (WS-48315, WS-55315, WS-65315, WS-65315A) : Locking by Time, Front Button Lock,V-Chip Rating Menu
Select On at Lock by Time, then select the Lock Time and Unlock Time. This will lock the entire TV. Your TV continues to be locked until you input your passcode, or when the locked time expires.
Setting the Front Button Lock to On will disable controls on the front panel to prevent anyone from accidentally changing settings. Off will restore the operations of the front panel buttons. If the front panel buttons have been locked and you misplace the remote control, you can restore the function of the front panel buttons by pressing and holding the MENU button on the front panel for more than 8 seconds. If the TV is already on, a message will be displayed to confirm the release of the Front Button Lock.
To block or allow programs based on the rating system described on page 45, select V-Chip to go to the V-Chip Rating menu.
48
V-CHIP Menu (WS-48315, WS-55315, WS-65315, WS-65315A ) : Allowing or Blocking Ratings, Lock by Time
Allowing or Blocking by Ratings
(Figure 36)
V-CHIP Menu (WS-48315, WS-55315, WS-65315, WS-65315A) : Allowing or Blocking Ratings, Lock by Time
Block or Allow programs based upon rating signals sent by the broadcasting station. The factory preset for TV Ratings is TV-PG (Parental Guidance) allowing only programs rated TV-PG or lower. The factory preset for Movies is PG, allowing only movies rated PG or lower. Please refer to page 45 for a detailed ratings description.
V-CHIP HOURS
V-CHIP HOURS will allow you to activate the V-Chip or lock the entire TV during specific hours. To set V-Chip Hours, select V-CHIP Hours from the V-CHIP LOCK menu.
Select the times you would like the V-Chip to be Active. By setting the V-Chip Start Time and VChip Stop Time to the same time, the V-Chip will be active 24 hours a day. Press or to slowly adjust the time. Press and hold or to quickly adjust the time.
Figure 37. V-CHIP HOURS, LOCK BY TIME for WS-48315, WS-55315, WS-65315, WS-65315A
49
ADVANCED FEATURES Menu: Color Balance, Auto Color Correction, PerfectColor , Reset Color
ADVANCED FEATURES Menu: Color Balance, Auto Color Correction, PerfectColor , Reset Color
The Color Balance Menu uses six colors (Magenta, Red, Yellow, Green, Cyan and Blue). You may adjust the intensity of these colors automatically or manually or reset them to the default settings.
Auto Color Correction optimizes skin tone color automatically and continuously. Manual Color Adjustment and Reset Color options are grayed out and unavailable when On is selected.
PerfectColor
(Figure 40)
Certain TV channels may appear more green or red than others. This is not a malfunction of the TV and may vary by channel or broadcaster. The PerfectColor menu allows you to adjust color settings based on your preferences. PerfectColor is only available when Auto Color Correction is turned Off. Press ENTER to display the menu for manual color adjustment. Individual color sliders will be displayed. They have a numeric value, where 63 is the maximum. The default setting for each color is 31 (center). Highlighted text will show which slider you are adjusting. For WT-42315 with a 480i signal, all inputs are adjusted at once. For WS-48315, WS-55315, WS-65315 or WS-65315A, each active input can be individually adjusted.
Press Adjust or to navigate between colors and Adjust or to change the color slider settings.
Reset Color
(Figure 39)
Select to reset the PefectColor settings. For WT-42315 with a 480i signal, all inputs are reset at once. For WS-48315, WS-55315, WS-65315, or WS-65315A each active input can be individually reset.
50
(Figure 41)
The timer will automatically turn the TV on (if it is off) at the time you schedule and select. When Ant-A or Ant-B is the selected input, you may select any memorized channel. The TV will tune to this channel when the timer turns it on.
The TVs clock must be set before you can set the timer. If you have not set the clock and/or day, you will see the CLOCK menu instead of the Timer menu.
TIMER menu
(Figure 42)
The timer can be turned On or Off. When On, you need to select the time and the day to turn On and the input and channel to display. At your preselected time, the timer will turn the TV on and a message will be displayed, Press a key for the TV to stay on. Any button on the remote control must be pressed within 5 minutes or the TV will turn itself off.
(Figure 43)
Set Time
Select the hour and minute, including AM or PM, when the TV is to turn on. Press or to slowly adjust the time. Press and hold or to quickly adjust the time.
51
(Figure 44)
Set Day
Select the days that the TV will turn on automatically. You can select Everyday, Mon-Fri (Monday through Friday), or the individual days of the week.
(Figure 45)
Input
Select the input to use when the timer turns on the TV. If the TV is already on, the timer will turn the TV to this selected input.
Channel
(Figure 46)
If the selected input is for Ant-A or Ant-B, the timer will turn the TV to the selected channel.
52
Your Mitsubishi TV has three picture tubes which need to be aligned to properly converge the projected light beams on the screen. Each picture tube projects a single color of red, blue or green. During production, your TV was carefully adjusted to properly align these colors. However, moving the TV, the TVs location in relation to the Earths magnetic poles, and the passage of time can cause these adjustments to change. As a special feature, you have the ability to adjust the red and blue light beams in reference to the fixed green light beam. This process is called convergence. There are two separate memories for convergence. One, for SD 480i/480p signals; the other for HD 1080i signals. SD convergence should be adjusted while watching an SD source and HD convergence should be adjusted while watching an HD source. The TV should be fully warmed up before adjusting Convergence. Turn the TV On and wait at least 30 minutes before starting adjustments.
Convergence Screen
(Figure 48)
When the Red and Blue crosshairs are properly converged, the center-screen crosshairs will appear white. You can use , , , or to move the Red and Blue crosshairs. Press VIDEO to switch between Red and Blue. Press AUDIO for the Advanced Convergence screen.
The convergence screen will timeout if no adjustments are made within a couple of minutes. If the screen does timeout, your adjustments will be saved. Pressing the CANCEL button will reset the convergence settings.
Advanced Convergence
(Figure 49)
After adjusting the Red Convergence and Blue Convergence, you can fine-tune your TV by adjusting the Red and Blue convergence at 64 individual points. Move the flashing bracket to a position needing adjustment by pressing , , , or .
53
Press ENTER to select the position (flashing will stop). Move the Red or Blue line by pressing , , , or . Press VIDEO to switch between the Red and Blue lines. A position is properly converged when all three lines combine to appear white. Press ENTER to deselect the position (flashing will resume), and move the brackets to the next position needing adjustment. When completed, press MENU to save your changes, and exit the Advanced Convergence screen. Note: This is considered a fixed image. Please see Important Notes on page 6, 12 or 30.
(Figure 50)
You may reset the red and blue convergence to factory default settings when you first use your TV or after making manual changes. Press the ENTER key to restore the convergence to the default settings. All the changes you made manually will be deleted. The message Convergence Completed appears when the convergence reset process ends.
Video Mute
(Figure 51)
Video Mute, (when On) lets you display a blue background when no signal is being received on Inputs 1-3, DTV, and Component 1-2 (Component only for WT-42315) and MonLink.
Black Enhancement
(Figure 52)
The contrast in dark scenes is enhanced for better picture quality. Brighter scenes will not be affected.
54
Each input has its own A/V memory. You can adjust each inputs A/V memory in two ways. You can use the menu or the remote control.
A/V Memory Reset will return the currently selected inputs A/V memory to the factory settings. To reset an inputs A/V memory, select A/V Memory Reset, select the input you want to reset, and press ENTER.
TV Speakers
This selection will turn on or off the TVs internal speakers. You may select Off when sending the sound through a separate stereo system or surround sound A/V receiver.
Select Fixed if your audio receiver or stereo system can be controlled with a remote. This allows you to adjust the volume with the systems remote control or the TV remote control, if compatible. This setting is better for surround sound receivers. Select Variable if your audio receiver or stereo system cannot be controlled with a remote. This allows the TVs internal circuitry to adjust the volume.
Audio Output
After selecting AUDIO SETTINGS or VIDEO SETTINGS, you can adjust the settings by pressing , , , or . For descriptions of the individual A/V settings, see AUDIO/VIDEO Setting Descriptions, pages 56-57.
55
Treble Enhances or reduces high frequency sound. Balance Adjusts the level of sound between the left and right speakers. Surround Creates simulated stereo and surround effects. Your choices are: Off: No surround effects. Use this setting when using an A/V receiver with Dolby Pro Logic Surround, or Dolby Digital Surround. Simulated Stereo: Your TV will create a simulated stereo effect when watching a nonstereo program. Surround Sound: Your TV will create a simulated surround effect when watching a stereo program. Listen to (for Ant-A and Ant-B) Determines how your TV will receive a broadcast audio signal and play back the sound you hear. Your choices are: Stereo: Default setting. The TV will play stereo broadcasts in stereo and mono broadcasts in mono. The word Stereo will be displayed when you tune to a channel broadcasting stereo. SAP (Second Audio Program): Additional monaural soundtrack that you cannot hear during normal TV viewing. The SAP signal might be related to the program you are watching, such as a soundtrack in a foreign language, or unrelated to the program you are watching such as a weather report. If a SAP signal is broadcast, the letters SAP will be displayed when you tune to the channel.
Note: A slider will display on-screen for each setting. The slider has a numeric value, where 63 is the maximum, the mid-range is 31 and the minimum setting is 0.
56
A compressed (non-HD) video signal may cause what appears to be a blurry, out of focus or fuzzy picture on a widescreen TV. This is not a malfunction of the TV, but a result of the compressed signal that is sent by cable or satellite. To re-adjust the picture, try the following: Adjust your video settings (specifically sharpness) for optimal picture performance. Use the Convergence Menu (page 53) to properly align the TV. Change the format size (pages 60-61). Contrast Provides a slider to adjust the white-to-black level. Low contrast shows a variety of shades in darker images, while high contrast shows darker images more uniformly black and makes colors appear more vibrant. Brightness Provides a slider to adjust the overall brightness of the picture. Sharpness Provides a slider to adjust the detail and clarity. Color Provides a slider to adjust the color intensity. Tint Provides a slider to adjust the proportion of red to green. Color Temp (Color Temperature) Allows you to adjust how white images are displayed. Your choices are: Low 6500K or Low (for DTV): White images will have a warm cast to them. This adjustment is an average and can vary due to ambient room lighting, video scene brightness and the TVs age. The Low 6500K represents the 6500K industry standard for NTSC (nonDTV) pictures.
57
58
Chapter . . .
PIP/POP Operations
Available On-Screen Format Sizes ........................................... 60 Operation of PIP and POP............................................................ 62 Appendix A: Bypassing the V-Chip Lock.................................... 63 Appendix B: HD Input Connection Compatibility ...................... 65 Appendix C: Remote Control Programming Codes .................. 66 Appendix D: Cleaning and Service ............................................. 68 Appendix E: Diamond Shield Installation and Removal ........ 69 Index............................................................................................... 72 Troubleshooting ............................................................................ 74 Warranty ........................................................................................ 75
Note: You can find aspect ratios on the back of most DVD covers. Also, Anamorphic DVDs are usually marked Anamorphic or Enhanced for 16:9 TVs. Standard
Default format for DTV and Component Input displays a full-screen format. The Standard format displays Anamorphic DVDs that have the 1.78:1 or 1.85:1 aspect ratios. However, Anamorphic DVDs that have the 2.35:1 aspect ratio still display black bars at the top and bottom of the screen, while narrow (4:3) images are stretched evenly from side to side.
Expand (480i/480p)
Enlarges the picture, cropping some of the image at the top and bottom. The Expand format reduces the letterbox top and bottom bars of non-Anamorphic DVDs or to correct narrow 4:3 images that have been stretched in the Standard format.
Note: Expand is not available in the 1080i format. HD Expand (1080i)
Enlarges the picture, cropping some of the image on both sides. This Expand format removes or reduce black side bars on HD broadcasts of 4:3 images with black bars. Note: Expand HD is only available in the 1080i format.
Zoom
Enlarges the picture, cropping some of the image at each side, top and bottom. The Zoom format removes or reduce the black top and bottom bars on Anamorphic DVDs with 2.35:1 aspect ratio. Note: This format is not available in the 1080i signal.
Stretch
Default format for Ant-A and Ant-B, and Inputs 1-3. The Stretched format stretches narrow 4:3 images across the screen, however, there is less stretch in the center than the sides. Note: Stretch is not available in the 1080i format .
Stretch Plus (not available on WT-42315)
Similar to stretch mode, however to minimize distortions on the side, the picture is expanded to crop off portions of the top and bottom. Useful when no important information is shown at the top and/or bottom of the screen.
Narrow
60
Displays narrow 4:3 images in their original shape and adds stationary gray side bars to fill the screen. The gray bars are considered a fixed image. See Important Notes on pages 6, 12, or 30. Note: This format is not available in the 1080i signal.
Standard (Recommended)
Standard (Recommended)
Expand
Stretch
61
Picture Inside Picture (PIP) vs. Picture Outside Picture (POP) You have the option to view two TV shows or inputs at the same time. For example, you can watch a game show and a sports event on another channel, or a DVD movie and more. The PIP option allows you to view another input as a picture-inside-picture. The POP option allows you to view a main picture and another input as a side-by-side or three or nine pictures-outside-picture at the side (only one moving POP).
Press PIP CH to scroll up or down through memorized channels on the Ant-A and Ant-B.
Press ENTER/EXCH to exchange the main picture with the PIP / POP picture.
Press ADJUST , , , or to move the PIP display anywhere on the main screen.
Press PAUSE to activate/pause automatic POP switching. When automatic POP switching is activated, the TV cycles through memorized channels, or strobes pictures from other A/V components in the POP display.
Press PAUSE in the TV layer to freeze the PIP and side-by-side images. Press Pause again to return to a live image.
62
Cut along the dotted line and file bypass instructions in a safe place for future reference.
When changing or deleting your passcode, you must use the remote control included with this TV. You cannot use a Mitsubishi remote control from another component or a universal remote.
63
64
Component Inputs
DTV Input
These inputs are compatible with most standard DVD and DTV signals with component video outputs. Compatible DTV signals are SDTV 480i, 480p, and HDTV 1080i. All other DTV signals, such as 720p, need to be converted by the DTV receiver (or compatible device) to one of the compatible signal types. Please check the specifications on your device before connecting. This input is also compatible with some DTV receivers using RGB or RGB with separate H and V sync. Industry standards for DTV RGB signals systems, synchronization, timing, and signal strengths are not currently established. These inputs will not be compatible with all DTV receivers that offer RGB. If your DTV receiver offers both DTV component video signals and DTV RGB signals, Mitsubishi suggests you use the DTV component video signals. Please check the DTV receiver specifications before connecting.
65
Cable Box
ABC .......................... 124 Archer ...................... 125 Cableview ................ 105 Citizen ...................... 122, 105 Color Voice .............. 128, 129, 130, 106,107 Comtronics .............. 128, 129, 130 ,106,107 Curtis........................ 112, 113 Diamond .................. 124, 125 Eagle ........................ 129 Eastern..................... 134 GC Brand ................. 105 GE ............................ 112, 113 Gemini...................... 122, 143 General Instrument /Jerrold..................... 119, 120, 121, 123 124, 125, 126,127 Hamlin...................... 112 Hitachi...................... 103, 124 Macom..................... 103, 104, 105, 108 Magnavox ................ 128, 129, 130, 106, 107, 133, 138 Memorex.................. 130 Movietime ................ 105 Oak........................... 102 Panasonic ................ 114 Paragon ................... 117 Philips ...................... 128, 129, 130, 106, 107, 133, 138, 131 Pioneer..................... 101, 116 Pulsar ....................... 105 RCA.......................... 115 Regal........................ 112 Regency................... 134 Rembrant ................. 105, 138 Samsung.................. 105 Scientific Atlanta...... 112, 113, 194 Signature.................. 119, 124, 125, 126, 127, 120, 121, 122 SL Mark.................... 105, 101 Sprucer .................... 105, Starcom ................... 119, 124, 125, 126, 127, 120, 121, 122 Stargate ................... 105 Teleview.................... 101, 105 Tocom ...................... 135, 136 Toshiba..................... 104 Unika ........................ 125 United Artists............... 102 United Cable ............ 119, 124, 125, 126, 127, 120, 121, 122 Universal .................. 122 Videoway.................. 106 Viewstar ................... 129, 130 Zenith/ Drake Satellite.......... 117, 100
DVD Players
Mitsubishi ................ 003 Aiwa.......................... 261, 274 Apex ......................... 266, 283 Bose......................... 286 Denon ...................... 250, 273 Ferguson.................. 251 GE/RCA/Proscan .... 251, 256 Harman Kardon ....... 282, 288 Hitachi...................... 270 JVC........................... 257 Kenwood.................. 271, 289 Mintek ...................... 285 Next Base ................ 284 Normande................ 251 Onkyo....................... 267, 280 Oritron ...................... 263, 268 Paite ......................... 262 Panasonic ................ 250 Philips/Magnavox .... 258, 253, 272, 290 Pioneer..................... 252 Saba......................... 251 Sampo ..................... 263 Samsung.................. 261 Sanyo ....................... 275 Sharp ....................... 260 SMC ......................... 275 Sylvania.................... 264 Sony ......................... 254, 278, 279 Thompson ................ 251 Toshiba..................... 253, 287 Venturer.................... 281 Vialta ........................ 277 Wave ........................ 269 XWave ...................... 269 Yamaha .................... 250, 272, 276, 287 Zenith ....................... 259
66
VCRs
Mitsubishi ................ 001, 002, 060, 067, 068, 061, 062 Admiral ..................... 055 Aiwa.......................... 047, 052 Akai .......................... 049, 034, 035, 036 Audio Dynamic......... 031 Bell & Howell............ 025 Broksonic................. 040, 046 Canon....................... 043, 045 Citizen ...................... 026 Craig......................... 025, 049, 026 Curtis Mathes .......... 065, 044, 047 Daewoo.................... 063, 021, 044, 078 DBX .......................... 030, 031 Dimensia .................. 065 Emerson................... 023, 038, 039, 040, 045, 046, 062, 063 Fisher ....................... 025, 028, 029, 027 Funai ........................ 047, 046, 040,054 GE ............................ 065, 044, 079, 053 Go Video .................. 057, 069, 070, 071 Goldstar ................... 026 Gradiente ................. 054 Hitachi...................... 043, 065, 020,047 Instant Replay.......... 044, 043 Jensen...................... 059 JVC........................... 030, 031, 054, 076, 077 Kenwood.................. 030, 026, 031 LXI ............................ 047, 026, 020, 027, 028, 025, 029 Magnavox ................ 051, 043, 044 Marantz.................... 030, 031 Marta........................ 026 Memorex.................. 044, 029 MGA ......................... 060, 067, 068, 061, 062 Minolta ..................... 020, 065 Multitech .................. 067, 047, 024 NEC.......................... 030, 031, 054 Olympic.................... 044, 043 Optimus ................... 048, 041, 055, 026 Orion ........................ 046, 040 Panasonic ................ 043, 044, 041, 042 Penney ..................... 044, 020, 065, 025, 030, 031 Pentax...................... 020, 031, 065 Philco ....................... 051, 044, 047, 043, 046, 040, 063 Philips ...................... 051, 043, 044 Pioneer..................... 043 Proscan.................... 065, 020, 043, 044, 051, 066, 021, 022, 053 Quasar ..................... 041, 042, 043, 044 Radio Shack ............ 053, 044, 025, 056, 029, 060, 047
VCRs continued
RCA.......................... 053, 065, 020, 043, 044, 049, 051, 066, 021, 022 Realistic ................... 044, 025, 056, 029, 060, 047 Samsung.................. 057, 022, 024, 053 Sansui ...................... 046, 040, 072 Sanyo ....................... 025, 029 Scott ........................ 021, 022, 024, 029, 060, 067, 068, 046, 040 Sears........................ 025, 026, 027, 028, 020 Shaintom.................. 037 Sharp ....................... 055, 056 Signature 2000 ........ 047, 055 Singer....................... 037 Sony ......................... 048, 049, 050, 073, 074, 075 SV2000..................... 047 Sylvania.................... 051, 043, 044, 047 Symphonic............... 047 Tashiro...................... 026 Tatung....................... 030, 031 TEAC ........................ 030, 047, 031 Technics ................... 041, 042, 043, 044 Teknika ..................... 044, 047, 032 Toshiba..................... 021 Totevision ................. 026 Vector Research ...... 031 Wards........................055 056, 029, 064, 026 Yamaha .................... 025, 030, 031 Zenith ....................... 064,026
67
Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines:
First, turn off the TV and unplug the power cord General Cleaning Warnings: from the power outlet. DO NOT allow liquid to enter the TV through the ventilation slots or any crevice. Top and Sides of the TV: DO NOT use any strong or abrasive cleaners as Gently wipe down your TV with a soft, nonthese can scratch the surfaces. abrasive cloth such as cotton flannel or a clean cloth diaper, lightly moistened with water. Dry DO NOT use any cleaners with ammonia, with a second dry, soft, non-abrasive cloth. bleach, alcohol, benzine, or thinners as these can dull the surfaces. For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent to the water used to moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth. Screen behind the Diamond Shield: Follow the instructions for the top and sides, however, wipe gently in an up and down motion, following the grooves in the screen. DO NOT spray liquids or cleaners directly on the TVs surfaces. DO NOT scrub or rub the TV harshly. Wipe it gently.
If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or a Mitsubishi Clean the entire screen evenly, not just sections Authorized Warranty Service Center. of the screen. DO NOT adjust any controls other than those described in the Owners Guide. Do not allow liquid to drip down the grooves of the screen as some liquid may enter the TV between the screen and the screen frame. DO NOT remove the protective back cover of your TV. Menus not described and shown in this Owners Guide are designed for factory use and for Authorized Service Personnel. Damage caused to the TV by non-authorized changes or changes to those menus made by non-authorized persons are not covered under warranty.
Service
You may purchase Mitsubishi Screen Cleaner, part number CLEANER-VSS, by calling (800) 553-7278 Cloth speaker grills: Lightly brush with a soft brush cloth, or lint brush.
Do not use any kind of abrasive or liquid Cleaner on the surface of the TV screen or Diamond Shield.
WARNING: THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND/OR BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
68
Appendix E: Diamond Shield Installation and Removal for WS-48315, WS-55315, WS-65315 and WS-65315A
Follow the steps below to install and remove the Diamond Shield.
Installation: A. Begin by inserting the shield, sliding it into the channels, starting at the bottom. Gently bow the Diamond Shield toward you and insert the Diamond Shield into the top channel. B. Install the left and right molding clips by pressing them into the opening starting at a corner. Do not force the clip. The clip will slide into place. This completes the Diamond Shield installation. The Diamond Shield protects the actual television (lenticular) screen, however it can be removed to reduce glare or background reflections. Removal: To remove the Diamond Shield, reverse the order of the above procedure.
Diamond Shield Installation
Appendix E: Diamond Shield Installation and Removal for WS-48315, WS-55315, WS-65315 and WS-65315A
Sharp edges! Always wear gloves to handle, lift and install the Diamond Shield and molding clips. Sharp objects (such as tools, hand jewelry and fingernails) may scratch or damage the Diamond Shield. Use caution when removing or installing. Mitsubishi recommends using a flat, plastic card (such as a credit card) to remove the molding clips. Store the Diamond Shield in a safe place to prevent damage. Damage caused to the TV by non-authorized changes or actions are not covered under warranty. The Limited Warranty does not cover damage resulting from improper installation or removal of the Diamond Shield.
WARNING
The Diamond Shield on the WT-42315 is not designed to be removed by the customer.
69
70
CAUTION: This PTV for use only with Mitsubishi stand MB-42413. Use with other stands may result in instability causing possible injury.
When considering the location or position of your TV, we recommend you place it at least 2 (inches) away from the wall. Like most electrical equipment and appliances, better air circulation allows your television to run cooler, assuring a long, trouble-free life.
At Least 2 (Inches) Away from Wall
1. Remove the side panel from the accessories plastic bag attached to the back of your TV. 2. Route all of the cable downward so the cover can close over them. 3. Position the three tabs directly opposite the three slots (see diagram) and gently push toward the front of the TV. 4. Slide the two push tabs into the slots on the other side of the terminals until both tabs snap into place. Result: The side panel neatly covers the input jacks. Reverse these steps to remove the side panel from the input terminal.
Side Panel
Tabs
Push Tabs
Slots
71
Index
A
A/V
Memory Reset 55 Receiver, Connecting 17
Composite Video with Audio, Connecting 16 CONNECTING Antenna or Wall Outlet Cable 14, 15 Antenna to a Cable Box and VCR 16 Antenna to a Cable Box or VCR 15 Audio Receiver 17 Audio Components to the Cable Box or VCR 16 DTV Receiver 19, 20 DVD Player 18 MonitorLink 21 S-Video Device 18 Connections Affect the PIP and POP 22 Convergence Menu Advanced 53 Screen 53
Activating the PIP and POP 29 Advanced Convergence Menu 53 Advanced Features Menu 34, 50-54 Antenna Channel Edit Menu 42 Connecting 14, 15 Appendices A: Bypassing the V-Chip Lock 63 B: High Definition Input Connection Compatibility 65 C: Remote Control Programming Codes 66 D: Cleaning and Service 68 E: Diamond Shield Installation and Removal for Models WS-48315, WS-55315, WS-65315, WS-65315A 69 Audio/Video Settings Menu 34, 55 A/V Memory Reset 55 Audio Output 55 TV Speakers 55 Audio Settings Menu 55 Audio Settings Description 56 Automatic POP Switching 62 Auto Color Correction Menu 50 Available On-Screen Format Sizes 60
D
Daylight Savings Time Menu 37 DTV Connectors and Adaptors 19 Input Connection Compatibility 65 DTV Receiver with Component Video Connections 19 RGB Video Connections 20 DVD Player with Component Video 18 DVI, Connecting 21
Index
E
Energy Mode for WS-48315, WS-55315, WS-65315, WS-65315A 39 Entering the Passcode for V-Chip 46 Exchanging Program Images PIP and POP 62
B
Back Panel Input/Output for WS-48315, WS-55315, WS-65315, WS-65315A 11 Black Enhancement Menu 54 Bypassing the V-Chip Lock 63
F
Freeze the PIP 62 Side-By-Side Picture 62 Front Button Lock for WS-48315, WS-55315, WS-65315, WS-65315A 48 WT-42315 38 Front Control Panel 10
C
Cabinet Separation for Model WS-65315, WS-65315A 70 Cable Box, Connecting 15, 16 Captions Menu 33, 40 Background 41 Closed Captions 41 Changing PIP/POP Channels 62 Inputs 62 Channel Menu 42, 52 Channel Edit Menu 33, 42 Channel Selection 26 Clock Setting Auto 37 Manual 36 Coaxial Lead Antenna, Connecting 14 Color Balance Menu 50 Component-1 and 2 Inputs Connection Compatibility 65
I
IMPORTANT Notes 6, 12, 30 Safeguards 4 Input Menu 52 Input Assignment Menu 35 Input Levels when used with RGB Video Signals 65 Component Video 65 Component Video Signals 65 Input when used with DVI 65
L
Language Menu 38
72
Lock by Time for WS-48315, WS-55315, WS-65315, WS-65315A 48 WT-42315 47 Lock Time for WT-42315 47
M
Main Menu Screens: Overview 32 Memorize Channels Menu 35 Memorize Menu 35 Memory Menu 43 Menus (also see individual topic) Advanced Features 50 Audio/Video Settings 55 Captions 40 Channel Edit 42 Main 32 Setup 35 V-Chip Lock 45 MonitorLink, Connecting 21 Moving PIP Images 62
Setup Menu 33 Set Day Menu 36, 52 Set Time Menu 51 Side Panel Input/Output for WT-42315 11 Sleep Timer 26 Special Features 9 SQV Using the Menu Screen 44 Remote Control 44 Stereo Audio System, Connecting 17
T
Timer Menu 51 Time Zone Setting 37 Troubleshooting 74 TV Speakers Menu 55 Twin Lead Antenna, Connecting 14
N
Name Menu 43
U
Unlock Time for WT-42315 47 Use of the Remote Control with Other A/V Products 27, 28 Using the AUDIO and VIDEO Buttons on the Remote Control 55
P
PerfectColor 50 PIP and POP Activating 29 Changing 62 Freezing 62 How Connections Affect 22 Operation 62 POP Live Image, Selecting 62
Index
V
V-Chip Allowing or Blocking by Ratings
for WS-48315, WS-55315, WS-65315, WS-65315A 49 for WT-42315 47
Exceptions: 45
R
Remote Control Functions Care 25 Channel Selection 26 Operation 25 PIP and POP 29 Overview of the TV Layer Button 24 Sleep Timer 26 Special Functions 29 Use with Other Brands of A/V Products 27 Reset Color 50 Reset Factory Defaults, Convergence Menu 54
S
S-Video Audio, Connecting 16 Device, Connecting 18 Separate UHF and VHF Antennas, Connecting 14 Setting Up the V-Chip Lock Passcode 46
V-Chip Hours Menu for WS-48315, WS-55315, WS-65315, WS-65315A 49 WT-42315 47 V-Chip Lock Menu 34, 45-49 Overview 45 Signal Information 45 Start Time, WS-48315, WS-55315, WS-65315, WS-65315A 49 Start Time, WT-42315 47 Start Time, WS-48315, WS-55315, WS-65315, WS-65315A 49 Stop Time WT-42315 47 V-Chip Rating Menu, Selecting 48 Video Mute 54 Video Settings Description 57 Video Settings 55 Viewpoint Menu System 32
W
Wall Outlet Cable, Connecting 14 Warranty 75
73
Troubleshooting
Problem
1. The TV remote control does not work.
Possible Solution
Check that the batteries are installed correctly. Check that the selected switch is set to TV. Be no further than 20 feet from the TV when using the remote control. Press ENTER after a channel number to avoid delays. Use the three digit number, i.e 002 for channel 2. Use number keys instead of CHANNEL up/down. Be sure the channel you want to view is in memory. Check that the TV is turned to the correct input source for that channel, by pressing the INPUT button. Make sure the V-Chip setting is Off (page 47). This is part of normal TV operation. The TV may be locked. The clock may not be set. Check to see if the MUTE button is on. The TVs Listen to: setting may be set to SAP. Check that TV Speakers setting is On. See Appendix A, Bypassing the V-Chip Lock (page 63). Energy Mode has been set to Low. Change to Standard (page 39). Make sure the V-Chip setting is Off (page 47). Not all inputs can be displayed as a PIP (page 22). The TVs Listen to: setting may be set to SAP. If using stereo or A/V receiver speakers, check input selection on the stereo or A/V receiver. If using stereo or A/V receiver, check that AUDIO is from MONITOR OUT on TVs back panel. TV closed captioning has been set to text mode, but no text information is being broadcast. Turn Off in the CAPTIONS menu (page 40). Adjust Convergence (page 53). Check the Sharpness settings (page 57). If you connected your VCR with A/V cables, use the INPUT button to select the Input source (INPUT-1, INPUT-2, or INPUT-3) that the VCR is connected to. Check your VCRs owners guide for further troubleshooting. Make sure device is set to Output DVI in Device Menu. You may need to hook up to an analog input for initial setup. Make sure device is set to output at 480p or 1080i via YPbPr or RGB (check device output for compatibility). Make sure that V-Chip is On (page 47). If V-Chip Hours/Lock by Time is currently set to disable the V-Chip lock, the V-Chip will not block programming. Follow the steps below to reset system defaults to factory settings: 1. Press the MENU button followed by number buttons 1,2,and 3 on the remote control. Result: The Reset System Default menu screen is activated. 2. Press the ENTER button on the remote control. Result: The settings reset to factory defaults. 3. Press HOME or MENU on the remote control to return to the HOME or MENU screen. IMPORTANT: This function is not recommended unless it is mandatory to reset system defaults to factory settings. This operation CANNOT be undone and all customs settings will be erased.
2. 3.
The TV takes several seconds to respond to channel commands. You cannot access a channel.
4. 5. 6.
On-screen displays appear each time you change a function. The TV cannot be programmed to turn on automatically. There is no sound even when the volume is turned up. You have forgotten your lock passcode. Connected devices do not work correctly when the TV is off. PIP does not display a picture. The sound does not match the screen picture.
7.
Troubleshooting
8. 9. 10.
11.
There is a large black or gray rectangle on the screen. Picture is out of focus, or colors are not aligned. You cannot see a picture when you play a VCR tape.
12. 13.
14.
There is no picture when using MonitorLink/DVI input with an HDTV receiver or DVD player. No picture displays when using component inputs. V-Chip is not working.
15. 16.
17.
74
If you have questions that cannot be answered from this book, please call our Consumer Relations advisors at (800) 332-2119 or send an email to: [email protected] To order replacement remote controls or an Owners Guide, please call our Parts Department at (800) 553-7278 or contact us through our web site at: www.Mitsubishi-tv.com