Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

FlexiPacket Zero Footprint

Site Installation Abstract


(This document does not contain information on commercial availability)

A25000-A1204-A031-01-76P1
(May 2011)

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES,SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2010. All rights reserved.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 1

Site Installation Abstract

Name of the Radio Solution Outdoor Unit

= =

FlexiPacket Zero Footprint FlexiPacket Radio FlexiPacket MultiRadio

Mechanical compatibility Frequency Range Capacity FPR Configuration BTS

= = = = =

XD, FH 7-8-13-15-18-23-26-28-32-38 GHz Ethernet traffic 1+0 Flexi Multiradio WCDMA/LTE BTS Flexi EDGE BTS Flexi Multiradio EDGE/GSM BTS

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 2

INDEX 1
-

Flexi Multiradio WCDMA/LTE BTS


Tail site 1+0 - ODU-BTS distance up to 2m - Direct Powering Tail site 1+0 - suggested DC powering with ODU-BTS distance >2m Tail site 1+0 - ODU-BTS distance >2m Flexi Multiradio WCDMA/LTE BTS Tail sites with 2 ODU DC Power connector to power supply the FPR Sheet Sheet Sheet Sheet Sheet 4 5 6 7 8

2
-

Flexi EDGE BTS


System Module Sheet 9

3
-

Flexi Multiradio GSM/EDGE BTS


System Module (ESMB/C) Sheet 10

4
-

FlexiPacket Radio - IN/OUT Ethernet Cable


ODU <-> Power Injector FLEXI BTS <-> Power Injector FLEXI BTS <-> ODU Sheet Sheet Sheet 11 12 13

5
-

FlexiPacket Radio - DC OUTDOOR POWER CABLES


DC outdoor power cables Sheet 14

6
-

FlexiPacket Radio - 2m DC CABLE


FLEXI BTS <-> FSEC Sheet 15

7
-

FlexiPacket Radio - DC CABLE


ODU <-> Power Injector or FSEC FLEXI BTS <-> ODU Sheet Sheet 16 17

8
-

FlexiPacket MultiRadio - IN/OUT Ethernet Cable


ODU <-> Power Injector FLEXI BTS <-> Power Injector FLEXI BTS <-> ODU Sheet Sheet Sheet 18 19 20

9
-

FlexiPacket MultiRadio - DC OUTDOOR POWER CABLES


DC outdoor power cables Sheet 21

10 FlexiPacket MultiRadio - 2m DC CABLE


FLEXI BTS <-> FSEC Sheet 22

11 FlexiPacket MultiRadio - DC CABLE


ODU <-> Power Injector or FSEC FLEXI BTS <-> ODU Sheet Sheet 23 24

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 3

Flexi Multiradio WCDMA/LTE BTS


Tail site 1+0 - ODU-BTS distance up to 2m - Direct Powering

FlexiPacket Radio

PS cable P/N T555PSBS.04 DC outdoor power cable (See sheet 17 for FPR and sheet 24 for FPMR) (Note 1) Flexi Multiradio BTS System Module Case

ETH P/N T555ETBS.04 (See sheet 12 for FPR and sheet 19 for FPMR) (Note 2)

Transport Sub-Module

Flexi Multiradio BTS System Module

Note 1: 4m DC outdoor power cable (To be shortened to max 2 m in outdoor installations). Note 2: Preassembled connector (BTS side), to be assembly in field with FPR Eth. Connector (ODU side).

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 4

Flexi Multiradio WCDMA/LTE BTS


Tail site 1+0 - suggested DC powering with ODU-BTS distance >2m (Power Injector Outdoor)

FlexiPacket Radio

Direct -48VDC Power Injector for outdoor installation

Flexi Multiradio BTS System Module Case

P+ETH P/N T555ETCB.23 Outdoor Ethernet cable (See sheet 11 for FPR and sheet 18 for FPMR)

ETH P/N T555ETBS.04 or P/N 471408A FTCR Outdoor CABLE (See sheet 12 for FPR and sheet 19 for FPMR) (Note 2) PS cable P/N T555PSBS.04 DC outdoor power cable (See sheet 14 for FPR and sheet 21 for FPMR) (Note 1) Flexi Multiradio BTS System Module Transport Sub-Module

Note 1: 4m DC outdoor power cable (To be shortened to max 2 m in outdoor installations). Note 2: Preassembled connector (BTS side), to be assembly in field with FPR Eth. Connector (ODU side).

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 5

Flexi Multiradio WCDMA/LTE BTS


Tail site 1+0 - ODU-BTS distance >2m (with FSEC unit and without Power Injector Outdoor)

FlexiPacket Radio

FSEC module P/N 47197A

FSEC module bottom view detail PS cable P/N T555PSCB.13 DC outdoor power cable (See sheet 16 for FPR and sheet 23 for FPMR)

Flexi Multiradio BTS System Module Case

ETH 4/15/30/50/70/100 m GbEth outdoor Cables: P/N T555ETBS.04/15/30/50/70/100 (See sheet 13 for FPR and sheet 20 for FPMR) (Note 2) FSEC PS cable DC outdoor power cable (See sheet 15 for FPR and sheet 22 for FPMR) (Note 1) Transport Sub-Module

Flexi Multiradio BTS System Module Note 1: This cable is provided with the FSEC terminated at both sides and must be cut at one side. Note 2: Preassembled connector (BTS side), to be assembly in field with FPR Eth. Connector (ODU side).

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 6

Flexi Multiradio WCDMA/LTE BTS


Flexi Multiradio WCDMA/LTE BTS Tail sites with 2 ODU (FOC + Power Injector Indoor) FlexiPacket Radio

Flexi Outdoor Case (FOC)

P+ETH P/N T555ETCB.23 Outdoor Ethernet cable (See sheet 11 for FPR and sheet 18 for FPMR)

ETH P/N T555ETBS.04 or P/N 471408A FTCR Outdoor CABLE (See sheet 12 for FPR and sheet 19 for FPMR) (Note 2)

P/N T55248.84 Outdoor Power cable

Flexi Multiradio BTS System Module Case

PS cable P/N T555248.30 3.5 m Outdoor power cable (See sheet 14 for FPR and sheet 21 for FPMR) (note1) Transport Sub-Module

Flexi Multiradio BTS System Module Note 1: 3.5m DC outdoor power cable (To be shortened to max 2 m in outdoor installations). Note 2: Preassembled connector (BTS side), to be assembly in field with FPR Eth. Connector (ODU side).

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 7

Flexi Multiradio WCDMA/LTE BTS


DC Power connector to power supply the FPR

CASE 1: Only 1 System Module To FPR DC power distribution to RF Units and Extension module

Transport Sub-Module

DC (EXT)

System Module

CASE 2: Two System Modules

DC cable part of FSKA System module extension cable kit

To FPR

Transport Sub-Module

DC (EXT)

DC (EXT)

System Module (Main)

System Module (Extension)

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 8

Flexi EDGE BTS


System Module

With the Flexi EDGE BTS all the configurations shown in Sheet 4 to Sheet 7 are available (by using the same cables).

Use one of these PWR connectors to power supply the FPR

FIQB/FIYB Transport Module

EIF3

EIF1

EIF2 EIF1 and/or EIF2 to FlexiPacket Radio

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 9

Flexi Multiradio GSM/EDGE BTS


System Module (ESMB/C)

With the Flexi Multiradio GSM/EDGE BTS all the configurations shown in Sheet 4 to Sheet 7 are available (by using the same cables).

Use one of these PWR connectors to power supply the FPR

FIQB/FIYB Transport Module

EIF3

EIF1

EIF2 EIF1 and/or EIF2 to FlexiPacket Radio

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 10

FlexiPacket Radio - IN/OUT Ethernet Cable


ODU <-> Power Injector

Max. length: 100 m

8-pin Lemo connector (P/N T555ETLE.08)

Ethernet cable (P/N T555ETCB.23)

Ethernet cable connection


ODU side: male shielded LEMO multipolar connector with 8 golden power pins (24 AWG). Power Injector: terminated with a shielded RJ45. The cable is double shielded, four twisted pairs, Cat 5e. In order to minimize the power loss in the cable, the minimum required value for the AWG is 24. Cable materials are designed for outdoor conditions. The cable shield shall be connected to the FlexiPacket Radio grounding point. Lemo connector Pin # 1 2 3 4 5 6 7 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 2 (orange) 1 (white/blue) 1 (blue) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8 Pin # RJ45 connector Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

Note: To terminate the Ethernet cable, use the relevant crimping tool.
FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 11

FlexiPacket Radio - IN/OUT Ethernet Cable


FLEXI BTS <-> Power Injector

RJ45 (to Flexi BTS)

Ethernet cable connection

FTCR OD CABLE RJ45 CAT5E 15 m (P/N 471408A) or Preassembled GBe outdoor cable 4 m (P/N T555ETBS.04)

FLEXI BTS side: preassembled with a shielded RJ45 and rubber gasket. Indoor side: to be terminated with a shielded RJ45 at the suitable length.

RJ45 connector (System Module Side) Pin # 1 2 3 4 5 6 7 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8

RJ45 connector (Power Injector side) Pin # Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

Note: To terminate the Ethernet cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 12

FlexiPacket Radio - IN/OUT Ethernet Cable


FLEXI BTS <-> ODU

FLEXI BTS SIDE

RJ45 (to Flexi BTS)

Preassembled GBe outdoor cable 4/15/30/50/70/100 m P/N T555ETBS.04/15/30/50/75/95

ODU SIDE

8-pin Lemo connector (P/N T555ETLE.08)

Ethernet cable connection


ODU side: male shielded LEMO multipolar connector with 8 golden power pins (24 AWG). FLEXI BTS side: preassembled with a shielded RJ45 and rubber gasket. Lemo connector Pin # 1 2 3 4 5 6 7 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 2 (orange) 1 (white/blue) 1 (blue) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8 Pin # RJ45 connector Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 13

FlexiPacket Radio - DC OUTDOOR POWER CABLES


DC outdoor power cables

4m DC outdoor power cable (10.3 mm outer diameter) (P/N T555PSBS.04)

(to Flexi BTS)

(to Power Injector)

Note: To be shortened to max 2 m in outdoor installations.

3.5m DC outdoor power cable for FOC installation (6.5-7 mm outer diameter) (P/N T555248.30)

(to FOC) (to Flexi BTS)

Note: To be shortened to max 2 m in outdoor installations.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 14

FlexiPacket Radio - 2m DC CABLE


FLEXI BTS <-> FSEC

Note: This cable only comes included in the FSEC delivery (it is not a sellable item).

This side must be cut (to FSEC)

DC outdoor power cable

(to Flexi BTS)

Note: It is terminated at both sides and must be cut at one side.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 15

FlexiPacket Radio - DC CABLE


ODU <-> Power Injector or FSEC

Max. length: 100 m

2-pin Lemo connector (P/N T555PSLE.02)

PS cable (P/N T555PSCB.13)

PS cable connections
Outdoor side: male shielded LEMO multipolar connector with 2 golden power pins (13 AWG). Indoor side: terminate the cable on the Power Injector.

Pin number A1

Signal name Battery +

Note Internally this pin is floating. During installation can be grounded or not. -

Color wire Brown

A2

Battery -

Blue

Note: To terminate the PS cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 16

FlexiPacket Radio - DC CABLE


FLEXI BTS <-> ODU (FLEXI BTS side)

4m DC outdoor power cable (P/N T555PSBS.04)

(ODU side)

PS cable connections
ODU side: male shielded LEMO multipolar connector with 2 golden power pins (13 AWG). FLEXI BTS side: preassembled DC cable.

Pin number A1

Signal name Battery +

Note Internally this pin is floating. During installation can be grounded or not.

Color wire Brown

A2

Battery -

Blue

Note 1: To be shortened to max 2 m in outdoor installations. Note 2: To terminate the PS cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 17

FlexiPacket MultiRadio - IN/OUT Ethernet Cable


ODU <-> Power Injector

Max. length: 100 m

8-pin Amphenol connector (P/N T555ETAM.08)

Ethernet cable (P/N T555ETCB.23)

Ethernet cable connection


ODU side: male shielded AMPHENOL multipolar connector with 8 golden power pins (24 AWG). Power Injector: terminated with a shielded RJ45. The cable is double shielded, four twisted pairs, Cat 5e. In order to minimize the power loss in the cable, the minimum required value for the AWG is 24. Cable materials are designed for outdoor conditions. The cable shield shall be connected to the FlexiPacket MultiRadio grounding point. Amphenol connector Pin # 7 3 5 1 4 2 6 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8 Pin # RJ45 connector Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

Note: To terminate the Ethernet cable, use the relevant crimping tool.
FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 18

FlexiPacket MultiRadio - IN/OUT Ethernet Cable


FLEXI BTS <-> Power Injector

RJ45 (to Flexi BTS)

Ethernet cable connection

FTCR OD CABLE RJ45 CAT5E 15 m (P/N 471408A) or Preassembled GBe outdoor cable 4 m (P/N T555ETBS.04)

FLEXI BTS side: preassembled with a shielded RJ45 and rubber gasket. Indoor side: to be terminated with a shielded RJ45 at the suitable length.

RJ45 connector (System Module Side) Pin # 1 2 3 4 5 6 7 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8

RJ45 connector (Power Injector side) Pin # Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

Note: To terminate the Ethernet cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 19

FlexiPacket MultiRadio - IN/OUT Ethernet Cable


FLEXI BTS <-> ODU

FLEXI BTS SIDE

RJ45 (to Flexi BTS)

Preassembled GBe outdoor cable 4/15/30/50/70/100 m P/N T555ETBS.04/15/30/50/75/95

ODU SIDE

8-pin Amphenol connector (P/N T555ETAM.08)

Ethernet cable connection


ODU side: male shielded AMPHENOL multipolar connector with 8 golden power pins (24 AWG). FLEXI BTS side: preassembled with a shielded RJ45 and rubber gasket. Amphenol connector Pin # 7 3 5 1 4 2 6 8 Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown) 1 2 3 4 5 6 7 8 Pin # RJ45 connector Pair 3 (white/green) 3 (green) 2 (white/orange) 1 (blue) 1 (white/blue) 2 (orange) 4 (white/brown) 4 (brown)

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 20

FlexiPacket MultiRadio - DC OUTDOOR POWER CABLES


DC outdoor power cables

4m DC outdoor power cable (10.3 mm outer diameter) (P/N T555PSBS.04)

(to Flexi BTS)

(to Power Injector)

Note: To be shortened to max 2 m in outdoor installations.

3.5m DC outdoor power cable for FOC installation (6.5-7 mm outer diameter) (P/N T555248.30)

(to FOC) (to Flexi BTS)

Note: To be shortened to max 2 m in outdoor installations.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 21

FlexiPacket MultiRadio - 2m DC CABLE


FLEXI BTS <-> FSEC

Note: This cable only comes included in the FSEC delivery (it is not a sellable item).

This side must be cut (to FSEC)

DC outdoor power cable

(to Flexi BTS)

Note: It is terminated at both sides and must be cut at one side.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 22

FlexiPacket MultiRadio - DC CABLE


ODU <-> Power Injector or FSEC

Max. length: 100 m

2-pin Amphenol connector (P/N T555PSAM.02)

PS cable (P/N T555PSCB.13)

PS cable connections
Outdoor side: male shielded AMPHENOL multipolar connector with 3 golden power pins (13 AWG). Indoor side: terminate the cable on the Power Injector.

Pin number 1

Signal name Battery +

Note Internally this pin is floating. During installation can be grounded or not.

Battery -

Note: To terminate the PS cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 23

FlexiPacket MultiRadio - DC CABLE


FLEXI BTS <-> ODU (FLEXI BTS side)

4m DC outdoor power cable (P/N T555PSBS.04)

(ODU side)

PS cable connections
ODU side: male shielded AMPHENOL multipolar connector with 3 golden power pins (13 AWG). FLEXI BTS side: preassembled DC cable.

Pin number 1

Signal name Battery +

Note Internally this pin is floating. During installation can be grounded or not.

Battery -

Note 1: To be shortened to max 2 m in outdoor installations. Note 2: To terminate the PS cable, use the relevant crimping tool.

FlexiPacket Zero Footprint Site Installation Abstract A25000-A1204-A031-01-76P1

Sheet 24

You might also like