CCIVALVE Desuper Heater
CCIVALVE Desuper Heater
z z z z
Simple design only one moving part. Requires no external water control valve. Tight shut off single seat design. Fits steampipes 50 100 mm / 2" - 4".
z z z
Simple mounting between standard flanges. Good accuracy temperature control of the steam down to 8C / 15F above saturation. Particularly suitable when small cooling water quantities are required.
General
The BTG Steam Desuperheater MDA-14 is a selfcontained unit complete with its own actuator. It is designed for the attemperation of steam in pipe lines of small dimensions and where small quantities of cooling water are required. Its design is to a very large degree identical to the BTG MDA-V Steam Desuperheater. It will with good accuracy allow control of the steam temperature down to 8C / 15F above saturation.
Design
The MDA-14 is a combination of a spray water valve and an injection nozzle. It is available in pressure classes up to DIN PN 250, ANSI 1500. The unit is usually delivered for installation between standard flanges, however butt-welds are available as an option. The built-in water valve is of single seat design and has a tight shut off to Class V, ANSI B16.104. The differential pressure steam / water should not be higher than 25 bar / 375 psi this to avoid nozzle erosion and not less than 5 bar / 75 psi to ensure a good controlability. 10 bar / 150 psi is a suitable difference. For large pressure differentials up to 40 bar / 600 psi a special design with stellited seat and plug is available. A pneumatic actuator positions the one-piece stem / control plug assembly according to the required cooling water flow. Fig 1 BTG Steam Desuperheater MDA-14 with integrated water control valve
Technical data
Type Made by Water Capacity Rangeability Pressure class MDA-14 Steam Desuperheater BTG See graph 25:1 DIN, PN 16-250, ANSI 150-1500
Data sheet
D526.20/2en
Desuperheater
MDA-14
5 - 25 bar / 75 - 375 psi 40 bar / 600 psi with stellited seat and plug. For good evaporation 8 - 12 m/s (26 - 39 fps) but min. 6 m/s (20 fps). SS 1430 or SS 2216 (approx. equivalent to DIN H II / ASTM A 285 Gr.C or DIN 13CrMo44 / ASTM A 182-F12) SS 2303-03 (approx. equivalent to DIN X20Cr13 / ASTM AISI 420) SS 2303-03, nitrided SS 2303-03, nitrided Grafoil SS 2940, nitrided (approx. equivalent to DIN 34CrA1Mo5 / ASTM AISI 420) SS 2303-03
Main Applications
The range of possible applications for the BTG MDA-14 is very wide. The great majority are however found in the following standard industrial installations. Power plants which beside the large flow sector also supply process steam to auxiliaries, heating systems, soot blowers etc. Reduction of the temperature of superheated steam or gas where excess temperature will harm the product. Wherever balancing or make-up steam is required in low flow systems in refiners and processing plants.
Material -Body
-Nozzle (water)
Dimensioning of MDA-14
The required cooling water flow and the most suitable size for an MDA-14 is normally calculated by BTG. For this purpose we need the data listed under Quotation and order specification found on page 4.
-Gland nut
Function
The flute configuration of the plug together with the venturi design with a sharp egde on the steam entry side guarantees a high steam velocity at the point of water injection. This will assist in the atomization of the water into very small droplets that quickly will evaporate. The vortex created when the steam leaves the edge of the desuperheater nozzle will carry the water droplets some distance downstream the nozzle. This will ensure a good and fast evaporation of the injected water without risk of water impingement on the pipe wall. The rangeability depends on the velocity of the steam. If e.g. the steam velocity is 90 m/s (295 fps) you can acheive a turn down ratio of 15:1 as absolute min. velocity accepted is 6 m/s (20 fps).
D526.20/2en
CCI
Dimensions
DN-size mm 50 65 80 100 in. 2 1.5 3 4 mm 162 177 187 217 A in. 6.4 7.0 7.4 8.6 mm 115 130 140 170 B in. 4.5 5.1 5.5 6.7 mm 170 175 190 190 C in. 6.7 6.9 7.5 7.5 mm 60 60 60 80 D in. 2.4 2.4 2.4 3.2 mm 130 110 110 140 E in. 5.1 4.3 4.3 5.5 mm 56 56 56 75 F in. 2.2 2.2 2.2 3.0
Fig 3 1 2 3 4 5 6 7
MDA-14 Main Dimensions Body Nozzle/Seat Stem/Plug Seat Stem packing Gland bushing Gland nut
CCI
D526.20/2en
Desuperheater
= =
t3 p3
Data sheet
Box 603, SE-661 29 Sffle, Sweden Phone +46 533 689 600, Fax +46 533 689 601 e-mail: [email protected], www.ccivalve.com