Professional Documents
Culture Documents
Atv212 Programming Manual en S1a53838 02
Atv212 Programming Manual en S1a53838 02
S1A53838
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Schneider Electric. All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer should perform repairs to components. When devices are used for applications with technical safety requirements, the relevant instructions must be followed. Failure to use Schneider Electric software or approved software with our hardware products may result in injury, harm, or improper operating results. Failure to observe this information can result in injury or equipment damage. 2011 Schneider Electric. All rights reserved.
S1A53838 09/2011
Table of Contents
Table of Contents
General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 1 Chapter 2 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Steps for setting-up the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Factory configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Preliminary recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Embedded display terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Monitoring Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Menu Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Graphic display option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Finding a parameter in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Detected fault screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Pre-alarms screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Modbus communication status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PCSoft software workshop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Structure of the parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Parameters that cannot be changed while the drive is running . . . . . . . . . . . . . . . . . . 37 Common control schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Drive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 3 Chapter 4 Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Quick menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Programming Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Parameter Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Macro Programming (AU4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Parameter Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Display of Submenu AUF (F738) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Motor Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Motor Control Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Other Motor Control Mode Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Motor Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Auto-tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Expert parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Supply Voltage Correction and Motor Voltage Limitation . . . . . . . . . . . . . . . . . . . . . . . 73
3
Chapter 5
S1A53838 09/2011
Table of Contents
Motor 2 Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Chapter 6 Chapter 7 Drive Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Application Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Application parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Skip Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 DC Injection Braking Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 I/O Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Logic Inputs Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Logic Input Function Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Relay Output Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Analog Input Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Analog Output Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Analog Input Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Active Logic Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Preset Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 +/- Speed Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Damper control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Display Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Display parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Detected Fault Management Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Time delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Catch On The Fly (F301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Overtorque Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Nuisance Overvoltage And Input Phase Detected Fault Avoidance . . . . . . . . . . . . . 133 Motor Overload Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Serial Communication Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Network communication between the ATV212 drive and a master controller . . . . . . 138 Data structure parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Start/Stop Control By Speed Reference Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Droop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Droop control principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Chapter 8
Chapter 9 Chapter 10
Chapter 11
Chapter 12 Chapter 13
Annex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Chapter 15 Chapter 16 Migration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Migration ATV21 - ATV212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Parameters Reset Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Parameter values that do not vary by reset type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Parameter values that vary according to reset type . . . . . . . . . . . . . . . . . . . . . . . . . . 166
S1A53838 09/2011
Table of Contents
Parameter values that vary According to drive rating, but not reset type . . . . . . . . . . 167 Parameter values that vary According to drive rating and reset type . . . . . . . . . . . . . 168 Parameter values that do not change if reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Chapter 17 User Settings Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
S1A53838 09/2011
Table of Contents
S1A53838 09/2011
Safety Information
Safety Information
Important Information
NOTICE Please read these instructions carefully and examine the equipment in order to familiarize yourself with the device before installing, operating or carrying out any maintenance work on it. The following special messages that you will come across in this document or on the device are designed to warn you about potential risks or draw your attention to information that will clarify or simplify a procedure. The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists, which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided, can result in death, serious injury, or equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation, which, if not avoided, can result in injury or equipment damage.
CAUTION
CAUTION, used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in equipment damage. PLEASE NOTE The word "drive" as used in this manual refers to the controller portion of the adjustable speed drive as defined by NEC. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this product. 2010 Schneider Electric. All Rights Reserved.
S1A53838 09/2011
At a Glance
Document scope The purpose of this document is to:
help you to set-up the drive, show you how to program the drive, show you the different menus, modes and parameters, help you in maintenance and diagnostics.
Validity note This documentation is valid for the Altivar 212 drive. Related documents
Title of Documentation ATV212 Quick Start ATV212 Installation manual ATV212 Modbus manual ATV212 BACnet manual ATV212 Metasys N2 manual ATV212 Apoge FLN P1 manual ATV212 LonWorks manual Multiloader manual SoMove Mobile manual ATV212 other option manuals: see www.schneider-electric.com Reference Number S1A53825 S1A53832 S1A53844 S1A53845 S1A53846 S1A53847 S1A53848 BBV48778 S1A51444
You can download the latest versions of these technical publications and other technical information from our website at www.schneider-electric.com.
S1A53838 09/2011
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Read and understand this manual before installing or operating the drive. Installation, adjustment, repair, and maintenance must be performed by qualified personnel. The user is responsible for compliance with all international and national electrical code requirements with respect to grounding of all equipment. Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH. Use only electrically insulated tools. DO NOT touch unshielded components or terminal strip screw connections with voltage present. DO NOT short across terminals PA/+ and PC/ or across the DC bus capacitors. Before servicing the drive: - Disconnect all power, including external control power that may be present. - Place a DO NOT TURN ON label on all power disconnects. - Lock all power disconnects in the open position. - WAIT 15 MINUTES to allow the DC bus capacitors to discharge. - Measure the voltage of the DC bus between the PA/+ and PC/ terminals to ensure that the voltage is less than 42 Vdc. - If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative. Do not repair or operate the drive. Install and close all covers before applying power or starting and stopping the drive. Failure to follow these instructions will result in death or serious injury.
DANGER
UNINTENDED EQUIPMENT OPERATION Prevent accidental grounding of logic inputs configured for sink logic. Accidental grounding can result in unintended activation of drive functions. Protect the signal conductors against damage that could result in unintentional conductor grounding. Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to achieve a safe state during and after a path failure. Examples of critical control functions are emergency stop and overtravel stop. Separate or redundant control paths must be provided for critical control functions. System control paths may include communication links. Consideration must be given to the implications of unanticipated transmission delays or failures of the link (1). Failure to follow these instructions can result in death, serious injury, or equipment damage.
(1) For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines for the Application, Installation, and Maintenance of Solid State Control and to NEMA ICS 7.1 (latest edition), Safety Standards for Construction and Guide for Selection, Installation and Operation of Adjustable-Speed Drive Systems.
S1A53838 09/2011
10
S1A53838 09/2011
General Overview
General Overview
I
What's in this Part? This part contains the following chapters:
Chapter 1 2 Setup Overview Chapter Name Page 13 15
S1A53838 09/2011
11
General Overview
12
S1A53838 09/2011
Setup
Setup
1
What's in this Chapter? This chapter contains the following topics:
Topic Steps for setting-up the drive Page 14
S1A53838 09/2011
13
Setup
INSTALLATION
1. Please, refer to the installation manual..
PROGRAMMING
2. Apply input power to the drive, but do not give a run command.
3. Configure
v the
Tips:
z z z
Before beginning programming, complete the customer setting tables, page 171. Perform an auto-tuning operation to optimize performance, page 71. If you get lost, return to the factory settings, page 62.
nominal frequency of the motor [Parameter reset] (tYP) = [50 Hz reset] (1) if this is not 50Hz, v the motor parameters, page 66, only if the factory configuration of the drive is not suitable, v the application functions in the Drive Control Parameters section, page 77 and the I/O Control Parameters section, page 89, only if the factory configuration of the drive is not suitable. 4. Adjust the application parameters
14
S1A53838 09/2011
Overview
Overview
2
What's in this Chapter? This chapter contains the following topics:
Topic Factory configuration Preliminary recommendations Embedded display terminal Monitoring Mode Run Mode Programming Mode Menu Navigation Submenus Graphic display option Finding a parameter in this document Detected fault screens Pre-alarms screens Modbus communication status PCSoft software workshop Structure of the parameter tables Parameters that cannot be changed while the drive is running Common control schemes Drive Operation Page 16 17 18 20 23 23 24 30 31 33 33 34 34 35 36 37 38 45
S1A53838 09/2011
15
Overview
Factory configuration
Drive factory settings The Altivar 212 is factory-set for the most common operating conditions:
z z z z z
[Mot cont. mode sel.] (Pt): [Variable torque] (Pt = 1). See page 67. [Upper limit freq] (UL) = 50.0 Hz. See page 82. [Low limit frequency] (LL) = 0.0 Hz. See page 82. [Switch. freq. level] (F300): depending on drive rating (see page 85) [Auto ramp] (AU1) = [Enable] (AU1 =1). See page 85.
Parameter which depends on Macro Programming [Auto set function] (AU4) = 0 (see page 63):
z z
z z z z
Command reference: logic inputs ([Command mode sel] (CMOd) = 0). See page 77. Speed reference: analog input VIA = 010 V or 020 mA ([Frequency mode sel] (FMOd) = 1, (F201)= 0). See [Frequency mode sel] (FMOd) page 77 and Analog Input Speed Reference page 106. F: run forward (F111= 2). See [LI F selection] page 90. R: preset speed 1 (F112= 6). See [LI R selection] page 90. RES: clear detected fault (F113= 10). See [LI RES selection] page 90. Drive ready for operation (F110= 1). See [Logic Funct 2 active] page 112.
If the above values are compatible with the application, the drive can be used without changing the settings.
16
S1A53838 09/2011
Overview
Preliminary recommendations
CAUTION
INCOMPATIBLE LINE VOLTAGE Before turning on and configuring the drive, ensure that the line voltage is compatible with the supply voltage range shown on the drive nameplate. The drive may be damaged if the line voltage is not compatible. Failure to follow these instructions can result in equipment damage. Power switching via line contactor
CAUTION
RISK OF DAMAGE TO THE DRIVE z Avoid operating the contactor frequently. z Power cycling must be MORE than 60 seconds. Failure to follow these instructions can result in equipment damage. User adjustment and extension of functions
z z
The display unit and buttons can be used to modify the settings and to extend the functions described in the following pages. Return to factory settings is made easy by the [Parameter reset] (tYP) (see page 62).
DANGER
UNINTENDED EQUIPMENT OPERATION Check that changes made to the settings during operation do not present any danger. We recommend stopping the drive before making any changes. Failure to follow these instructions will result in death or serious injury. Test on a low power motor or without a motor
z
In factory settings mode, [Output phase loss] (F605) (page 129) is active F605 = 3. To check the drive in a test or maintenance environment without having to switch to a motor with the same rating as the drive (particularly useful in the case of high power drives), set F605 to 0. Set [Mot cont. mode sel.] (Pt) = [Constant V/Hz] (0) (see page 67).
CAUTION
UNINTENDED EQUIPMENT OPERATION Motor thermal protection will not be provided by the drive if the motor 's nominal current is 20% lower than that of the drive. Find an alternative source of thermal protection. Failure to follow these instructions can result in equipment damage. Using motors in parallel
z
Set [Mot cont. mode sel.] (Pt) = [Constant V/Hz] (0) (see page 67).
CAUTION
RISK OF DAMAGE TO THE MOTOR Motor thermal protection is no longer provided by the drive. Provide an alternative means of thermal protection. Failure to follow these instructions can result in equipment damage. Using in single phase supply
z
CAUTION
RISK OF DAMAGE TO THE DRIVE Using ATV212 in single phase supply is only allowed in training mode with motor and without load. Failure to follow these instructions can result in equipment damage.
S1A53838 09/2011
17
Overview
PRG MON
% Hz
6 7 12 13
Loc Rem
MODE
8 9
ENT
10 11 14
RUN
STOP
RESET
LED/Key
Characteristics
1 Display RUN LED Illuminates when a run command is applied to the drive. Flashes when there is a speed reference present with a Run command. 2 Display PRG LED Illuminates when Programming mode is active. Flashes in AUF, GrU modes 3 Display MON LED Illuminates when Monitoring mode is active. Flashes in detected fault history display mode 4 Display unit 4 digits, 7 segments 5 Display unit LED The % LED illuminates when a displayed numeric value is a percentage. The Hz LED illuminates when a displayed numeric value is in hertz. 6 UP/DOWN keys Depending on the mode, you can use the arrows to: Navigate between the menus Change a value Change the speed reference when the UP/DOWN LED (7) is illuminated 7 UP/DOWN LED Illuminates when the navigation arrows are controlling the speed reference 8 Loc/Rem LED Illuminates when Local mode is selected 9 MODE Press to select the embedded display terminal mode. Run mode (default on power-up) Programming mode Monitoring mode Can also be used to go back to the previous menu. 10 Loc/Rem Switches between Local and Remote modes 11 ENT Press to display a parameters value or to save a changed value. 12 RUN LED Illuminates when the Run key is enabled 13 RUN Pressing this key when the RUN LED is illuminated starts the drive. 14 STOP Stop/reset key. In Local mode, pressing the STOP key causes the drive to stop based on the setting of parameter [Loc. mot stop mode] (F721). In Remote mode, pressing the STOP key causes the drive to stop based on the setting of parameter [Ext. fault stop Mode] (F603). The display will indicate a flashing E. If [HMI reset button] (F735) is set to 0, pressing the stop key twice will reset the drive, if the detected fault condition has been cleared.
18
S1A53838 09/2011
Overview
Embedded display terminal modes The Altivar 212 embedded display terminal has three modes of operation: Monitoring, Run and Programming. The drive powers up in the Run mode. To select a different mode, use the MODE key as illustrated below.
ATV212 drive Power Up RUN
% Hz
Run mode
MODE
MODE
Monitoring mode
MODE
Loc Rem
MODE
ENT
0.0
Hz
AUF
MON
Fr-F
RUN
STOP
RESET
The red LED in left side of the display indicates the current mode selected, RUN for Run mode, PRG for Programming mode and MON for Monitoring mode.
S1A53838 09/2011
19
Overview
Monitoring Mode
The Monitoring mode displays drive operational data in real time. To access the Monitoring mode, press the MODE key until the MON LED is illuminated. Then use the UP and DOWN keys to view up to 30 different types of data. C80
PRG
% Hz
Loc Rem
MODE
AUF F60. 0
ENT
RUN
STOP
RESET
MODE
MON
Fr-F
25 other parameters
MODE
t0. 10
RUN
0.0 n---
MODE
[Line voltage]
P 100
[Motor voltage]
q 60 c 90 L 70 h 80 H 75 o60.0 ..11
[Drive load %]
[Input power KW] [Output power KW] [Motor frequency] [Logic input map]
20
S1A53838 09/2011
Overview
Display example
Description
ON: OFF: FL RYA-RYC
0.1
u101 uc01 uE01 d50.0 b70.0 h85 H75 A16.5 1500 N50 n50 nErr
[CPU CTRL ver.] [CPU MMI ver.] [Memory ver.] [PID feedback] [PID computed ref.] speed reference [Total input power] [Total motor power] [Drive out. rat. cur. A] [Motor speed rpm] [Comm. counter 2] [Comm. counter 1] [Past fault] Examples: - 1 blink Err5 - 2 blink Err5 - 3 blink CFI2 - 4 blink nErr
CTRL version 101 MMI version 1.0 Version of memory Level of PID feedback, displayed either as Hz or in custom unit set by parameter [Customized freq val] (F702) Speed reference command to drive as computed by the PID function, displayed either as Hz or in custom unit set by parameter [Customized freq val] (F702) Accumulated input power consumed by the drive displayed in kWh Accumulated output power supplied by the drive displayed in kWh Drive nameplate rated output current in amperes Motor speed in rpm Displays the counter numbers of communication through the network Displays the counter numbers of communication only at normal state in every communication through the network The most recent detected fault stored in the detected fault history. If the drive is in a detected fault state, this is not the active detected fault. A detected fault is stored in the detected fault history after it is cleared by clear detected fault action. Press ENT to review drive state at time of detected fault. See Detected fault Display and History on page 21 and Diagnostics and troubleshooting on page 149 for more detail. There are 4 detected faults recorded. The detected fault 4 is cleared when a new detected fault appears.
ON: OFF:
N...1
Mb
ON: OFF:
RJ45 Rx
t0.10
Detected fault display and history When the drive detected faults, the graphic terminal displays a code. To review data about drive operation at the time of the detected fault, press the MODE key to enter the Monitoring mode. Then use the Up/Down keys to scroll through the data listed in table page 20. Up to five detected faults can be displayed on the graphic terminal in Monitoring mode: the present detected fault (if the drive is in a detected fault state) and the previous four detected fault codes. To review drive operation data recorded at the time of detected fault for a previous detected fault, press ENT when the code for the detected fault is displayed. See table below for the available information. When a detected fault is cleared or power is cycled to the drive, the present detected fault becomes Past detected fault 1.
S1A53838 09/2011
21
Overview
[Line voltage]
P100
[Motor voltage]
..11
0.1
[Relay map]
In both the monitoring mode and the detected fault history, it is possible to view the state of the logic inputs and the relay outputs. See previous tables on pages 20 and 21. Logic Input Map
ON: OFF: VIA F R RES
The ON or OFF status of each logic input is displayed in bits. VIA is included in this display if parameter F109 is set to either 1 or 2. Relay Output Map
ON: OFF: FL RYA-RYC
22
S1A53838 09/2011
Overview
Run Mode
To access the Run mode, press the MODE key until the drive operating frequency, a detected fault code, or a pre-alarm code is displayed. See Diagnostics and troubleshooting beginning on page 149 for the detected fault and pre-alarm codes. Changing the Display in Run Mode Motor operating frequency is the default value displayed on the graphic terminal in Run mode. This displayed value can be changed by setting parameter [Displayed param.] (F710). See page 120 for a list of the display choices. The displayed value can be expressed as a percentage of the drive rating, or in amperes or volts, as appropriate for the value displayed. The units can be changed by setting parameter [Unit value selection] (F701) (see page 120). In addition, the resolution of the speed reference and output frequency displays can be adjusted by setting parameters [Loc. speed ref. step] (F707) and [Display ref. resol.] (F708) (see pages 77 and 120).
Programming Mode
Use this mode to program the drive. To access the Programming mode, use the MODE key until the PRG indicator LED on the display is illuminated. See Menu Navigation page 24.
S1A53838 09/2011
23
Overview
Menu Navigation
Menu navigation diagrams below illustrate how to navigate through the programming menus and submenus. AUH [Quick menu] submenu
Programming mode
Fr-F
to AUH
ENT
SUBMENU
to uLu
[Auto ramp]
[Quick menu]
AU1
AUF
MODE
GrU
ACC
[Acceleration time 1]
dEC
IO
SUBMENU [I/O MENU]
[Deceleration time 1]
LL
COM
SUBMENU [COMMUNICATION MENU]
Sr7
[Preset speed 7]
Power Up
RUN
UL
0.0
Hz MODE
MODE
MODE
OLM
tHr
tHr
FM
[Mot Voltage Boost]
[AO scaling]
ub
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
Pt
uL
uLu
[Motor rated voltage]
MODE
uLu
[Motor rated voltage]
uL
LL
MODE
F415
% Hz
UL
F417
FH
[Max frequency]
ENT
F601
dEC
[Deceleration time 1]
RUN
STOP
RESET
F400
[Auto-tuning drive]
ACC
[Acceleration time 1]
to AUI
Fr
tYP
[Parameter reset]
FM
[AO scaling]
AU4
AU1
[Auto ramp]
AUH
to AUF
24
S1A53838 09/2011
Overview
Programming mode
Fr-F
AUF
GrU
IO
COM
Sr7
[Preset speed 7]
Power Up
[Motor overload prot]
RUN
0.0
Hz MODE
MODE
OLM
tHr
ub
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
uLu
MODE
uL
LL
MODE
% Hz
UL
Loc Rem
MODE
FH
[Max frequency]
ENT
dEC
[Deceleration time 1]
RUN
STOP
RESET
HEAd
(1)
ACC
[Acceleration time 1]
(xxx)
Fr
(xxx)
tYP
[Parameter reset]
(xxx)
FM
[AO scaling]
MODE
(xxx)
(xxx)
End
(1)
AU4
AU1
[Auto ramp]
ENT
AUH
MODE
to AUF
Note: If no parameter has been changed, AU1 is selected. (1) Flashes three times then displays previous parameter.
S1A53838 09/2011 25
Overview
Programming mode
Fr-F
to AUH
SUBMENU [Quick menu]
ENT
(4)
AUF
to GrU
(1) U--F
[Forward search]
GrU
MODE
(3)
U---
[Waiting search]
[Reverse search]
IO
COM
Sr7
[Preset speed 7]
Power Up
RUN
0.0
Hz MODE
MODE
OLM
tHr
ub
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
uLu
MODE
uL
LL
MODE
% Hz
UL
Loc Rem
MODE
FH
[Max frequency]
ENT
dEC
[Deceleration time 1]
RUN
STOP
RESET
ACC
[Acceleration time 1]
Fr
tYP
[Parameter reset]
FM
[AO scaling]
(1) Pressing the UP key searches the parameter list starting with the first one changed. (2) Pressing the DOWN key searches the parameter list starting with the last one changed. (3) The number of parameters displayed within the GrU menu depends upon how many have been altered from their factory settings. (4) When all the changed parameters have been displayed, the display returns to GrU.
AU4
AU1
[Auto ramp]
AUH
to AUF
26
S1A53838 09/2011
Overview
to AUH
SUBMENU [Quick menu] SUBMENU [EXTENDED MENU]
AUF
GrU
to F---
F--MODE
F912
[Reserved]
IO
F...
...
COM
F102
[Freq.2 bandw.]
Sr7
[Preset speed 7]
Power Up
RUN
0.0
Hz MODE
MODE
F101
[Freq. 2 reached]
OLM
tHr
F100
[Freq. 1 reached]
ub
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
uLu
MODE
uL
LL
MODE
% Hz
UL
FH
[Max frequency]
ENT
dEC
[Deceleration time 1]
RUN
STOP
RESET
ACC
[Acceleration time 1]
Fr
tYP
[Parameter reset]
FM
[AO scaling]
AU4
AU1
[Auto ramp]
AUH
to AUF
S1A53838 09/2011
27
Overview
to AUH
SUBMENU [Quick menu]
AUF
GrU
to F108
IO
MODE
COM
Sr7
Power Up
RUN
0.0
Hz MODE
MODE
OLM
tHr
ub
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
F132 [FL Relay Function]
uLu
MODE
F130 [RY Relay Function 1]
uL
MODE
% Hz
UL
Loc Rem
MODE
FH
[Max frequency]
ENT
dEC
[Deceleration time 1]
RUN
STOP
RESET
ACC
[Acceleration time 1]
F110
Fr
tYP
to FMSL
FMSL [AO funct. selection]
AU4
AU1
[Auto ramp]
AUH
to AUF
28
S1A53838 09/2011
Overview
to AUH
SUBMENU [Quick menu]
AUF
GrU
IO
to COM
to F800
F851
[Com. fault setting]
COM
MODE
Sr7
[Preset speed 7]
Power Up
RUN
F896
0.0
Hz MODE
MODE
OLM
F89.
tHr
F890
ub
[Network adress]
MON
Pt
[Mot cont. mode sel.]
Fr - F
PRG
AUF
MODE MODE
F829
[Network protocol]
uLu
MODE
F821
uL
F820
LL
MODE
% Hz
F803
UL
Loc Rem
MODE
F80.
FH
[Max frequency]
ENT
F800
RUN STOP
RESET
ACC
[Acceleration time 1]
to F851
Fr
tYP
[Parameter reset]
FM
[AO scaling]
AU4
AU1
[Auto ramp]
AUH
to AUF
S1A53838 09/2011
29
Overview
Submenus
The ATV212 drive features 6 submenus (see diagrams starting on page 24) that are designed to reduce the time and effort required to program application parameters. Parameters can be modified within these submenus.
F [EXTENDED MENU]
The extended parameter submenu provides access to parameters used for special settings and applications.
10 [I/O MENU]
The IO submenu provides access to parameters used for input/output setting.
30
S1A53838 09/2011
Overview
WARNING
LOSS OF CONTROL z Do not use the ATV21 and ATV12 terminal display (VW3A21101 and VW3A1006). z Only VW3A1101 is compatible with ATV212. Failure to follow these instructions can result in death, serious injury, or equipment damage. Description of the graphic display option With the graphic display option, which works with FLASH V1.1IE29 or higher, it is possible to display more text information than can be shown on the integrated display terminal.
1 Graphic display 7 ESC key: Press to select the graphic display mode. - Run mode (default on power-up) - Programming mode - Monitoring mode Can also be used to go back to the previous menu. Also corresponds to the MODE button of the embedded HMI 6 FWD/REV key: Press to reverse the direction of rotation of the motor
2 Function keys F1, F2 and F3: not assigned F4: Loc/Rem 3 STOP/RESET key 4 RUN key
5 Jog dial:
Press (ENT):
- To save the current value - To enter the selected menu or parameter Turn +/-: - To increment or decrement a value - To go to the next or previous line - To increase or decrease the reference if control via the graphic display option is activated
Note: Keys 3, 4, 5 and 6 can be used to control the drive directly, if control via the graphic display option is activated.
S1A53838 09/2011
31
Overview
Powering up the drive with graphic display option for the first time When powering up the graphic display option for the first time, the user has to select the required language.
Display after the graphic display option has been powered up for the first time. Select the language and press ENT.
ENT
LANGUAGE
ENT
The graphic display option to drive synchronization screen will now appear.
2 s or ENT
OPERATIONAL VALUE
0 Hz
Rem
Loc/Rem
32
S1A53838 09/2011
Overview
With the integrated display terminal and the optional graphic display terminal : Direct use of the parameter
code index, page 171, to find the page giving details of the displayed parameter.
With the graphic display option: The parameter code and the name are displayed.
Example: ACC
AUF: QUICK MENU vLv: Motor rated voltage AU1: Auto ramp ACC: Acceleration time 1 DEC:Deceleration time 1 LL: Low limit frequency Loc/Rem Rem
Then use the parameter code index, page 171, to find the page giving details of the displayed parameter.
EPHO: Output phase loss fault Loss of one or more output phases. Determine the cause of the missing output phase and rectify the problem. Set parameter F605 to 0.
Rem
Loc/Rem
This screen is displayed the detected fault type and diagnostic information related to the detected fault. Then use the alarm code table page 150 for more information. Line undervoltage
Rem
Loc/Rem
S1A53838 09/2011
33
Overview
Pre-alarms screens
Here some type of screens:
Current Limit pre-alarm
Alarm C Alarm P
OPERATIONAL VALUE
OPERATIONAL VALUE
29.0 Hz
Rem Loc/Rem Rem
29.0 Hz
Loc/Rem
OPERATIONAL VALUE
OPERATIONAL VALUE
29.0 Hz
Rem Loc/Rem Rem
29.0 Hz
Loc/Rem
OPERATIONAL VALUE
OPERATIONAL VALUE
29.0 Hz
Rem Loc/Rem Rem
29.0 Hz
Loc/Rem
This parameter is able to check the modbus communication on RJ45 and OpenStyle port.
Rem
Loc/Rem
B - A - COM Rx Tx
B - A - COM Rx Tx
34
S1A53838 09/2011
Overview
Description This PC software workshop is a user-friendly tool for setting up Altivar 212 drives. It includes different functions such as:
z z z
It can be downloaded free of charge from the internet at www.schneider-electric.com. Connection The PCSoft software workshop must be connected directly to the Modbus port on the drive using the PC serial port connection kit, reference VW3A8106 or by USB cable reference TCSMCNAM3M002P, or by bluetooth (see catalog on www.schneider-electric.com).
S1A53838 09/2011
35
Overview
Code
Name / Description
Adjustment range -
Factory setting 0
F400
0 1 2
[Disabled] [Initialize constant]: Application of individual settings of Auto Torque Boost [Auto Torque Boost] (F402) [Complete tune]: complete auto tuning. Parameter F400 is reset to 0 after the auto tuning is performed.
Value of parameter on graphic display option Parameter value on embedded display Name of parameter on graphic display option and description if needed. Parameter code on 4-digit 7-segment display Note: The text in square brackets [ ] indicates what you will see on the graphic display option.
36
S1A53838 09/2011
Overview
S1A53838 09/2011
37
Overview
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Read and understand the instructions in "before you begin" chapter, before performing the procedure in this section. Failure to follow these instructions will result in death or serious injury.
DANGER
UNINTENDED EQUIPMENT OPERATION z To modify the setting of the switches, the product must be switched off. z Do not change the setting of switch SW102 unless your system is properly wired. Failure to follow these instructions will result in death or serious injury. 2-wire control
PA/+
M
Run forward Run reverse
% Hz
Loc Rem
MODE
ENT
STOP
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
CC FM
SW102
A GND SCR
PP VIA VIB CC
1. Wire the logic inputs as indicated in the above figure. 2. Set switch SW102 to source. 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameters for 2-wire control as indicated in the following table:
Parameter CMOd [Command mode sel] F111 [LI F selection] F112 [LI R selection] Page 77 90 Setting 0 [Logic inputs] 2 [forward] 3 [reverse] Factory value 0 2 6
90
Note: If F111 and F112 are switched simultaneously, the drive will go at 0 speed.
38
S1A53838 09/2011
Overview
3-wire control
PO R/L1 S/L2 T/L3 PA/+ PC/U/T1 V/T2 W/T3 F R RES
RUN STOP
% Hz
Loc Rem
MODE
ENT
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
CC FM
SW102
A GND SCR
PP VIA VIB CC
1. Wire the logic inputs as indicated in the above figure. 2. Set switch SW102 to source. 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameters for 3-wire control as indicated in the following table:
Parameter CMOd [Command mode sel] F111 [LI F selection] F112 [LI R selection] F113 [LI RES selection] Page 77 90 Setting 0 [Logic inputs] 2 [forward] 49 [3-wire] 3 [reverse] Factory value 0 2 6 10
90
90
Reverse run R - Stop F - Forward start RES - Reverse start Line power
ON OFF ON OFF ON OFF ON OFF
S1A53838 09/2011
39
Overview
% Hz
Loc Rem
MODE
ENT
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
CC FM
SW102
A GND SCR
PP VIA VIB CC
1. Wire the analog input as indicated in the above figure. 2. Set switch SW100 to V (voltage). 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameters for external speed control potentiometer as indicated in the following table:
Parameter FMOd [Frequency mode sel] Page Setting 1 [Ref source VIA] 0 [AI] 0 [Enable] Factory value 1 0 0
77 90 108
40
S1A53838 09/2011
Overview
% Hz
Loc Rem
MODE
ENT
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
CC FM
SW102
1. Wire the analog input as indicated in the above figure. 2. Set switch SW100 to I (current). 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameters for 4-20 mA speed control as indicated in the following table:
Parameter FMOd [Frequency mode sel] Page
F109 [VIA selection] F200 [Auto/man speed ref] F201 [VIA ref point 1]
77 90 108 106
Factory value 1 0 0 0%
S1A53838 09/2011
41
Overview
PA/+
% Hz
Loc Rem
MODE
ENT
STOP
CC FM
I PTC
SW102
A GND SCR
PP VIA VIB CC
1. Wire the logic and analog inputs as indicated in the above figure. 2. Set switch SW102 to source. 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameters for preset speed as indicated in the following table:
Parameter F109 [VIA selection] F111 [LI F selection] F112 [LI R selection] F113 [LI RES selection] F118 [VIA LI selection] Sr1 [Preset speed 1] Sr2 [Preset speed 2] Sr3 [Preset speed 3] Sr4 [Preset speed 4] Sr5 [Preset speed 5] Sr6 [Preset speed 6] Sr7 [Preset speed 7] Page Setting 2 [LI source] 2 [forward] 6 [PS1] 7 [PS2] 8 [PS3] Factory value 0 2 6 10 7 15.0 20.0 25.0 30.0 35.0 40.0 45.0
90
90
90
90
90
112 112 112 112 112 112 112
Time (sec)
ON OFF ON OFF ON OFF ON OFF
F R RES VIA
42
S1A53838 09/2011
Overview
Serial communication
RJ45 connection Port open style connection Contact B A GND SCR Signal + GND Screen
PA/+
% Hz
Loc Rem
MODE
ENT
STOP
CC FM
I PTC
SW102
A GND SCR
PP VIA VIB CC
1. For Modbus serial communication, plug the network cable into RJ45 connector on the main control board. Connection can also be carried out using the open style port. 2. Program common parameters of ATV212 (see Quick Menu page 55). 3. Program specific parameters for serial communication as indicated in the following table:
Parameter CMOd [Command mode sel] FMOd [Frequency mode sel] F807 [Com channel choice] Page 77 Setting 2 [Communication] 4 [Serial com ref.] Factory value 0 1 1
77 139
Forced local
PA/+
% Hz
Loc Rem
MODE
ENT
STOP
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
Forced local
CC FM
SW102
A GND SCR
PP VIA VIB CC
1. Wire the logic input as indicated in the above figure. 2. Set switch SW102 to source. 3. Program common parameters of ATV212 (see Quick Menu page 55). 4. Program specific parameter for forced local as indicated in the following table:
Parameter F113 [LI RES selection] Page 90 Setting 48 [forced local] Factory value 10
S1A53838 09/2011
43
Overview
PID control
PO R/L1 S/L2 T/L3 PA/+ PC/U/T1 V/T2 W/T3 F R RES
RUN STOP
% Hz
Loc Rem
MODE
ENT
Feedback transmitter
PLC P24
Term SW103 VIA U VIB U SW100 I PTC
CC FM
SW102
A GND SCR
PP VIA VIB CC
1. Wire analog inputs as indicated in the above figure. 2. Set switch SW102 to source. 3. If the feedback is a milliamp signal, set switch SW100 to the I (current) position. If the feedback is a voltage signal, set switch SW100 to the V (voltage) position. 4. Program common parameters of ATV212 (see Quick Menu page 55). 5. Program specific parameters for PID control as indicated in the following table:
Parameter FMOd [Frequency mode sel] F109 [VIA selection] F200 [Auto/man speed ref] F360 [PID control enable] F359 [PID ctrl wait time] F362 [PID Prop Gain] F363 [PID Integral Gain] F366 [PID Derivative Gain] F380 [PID reverse error] F391 [Stop on LL hyst] F392 [PID wake up (thres)] F393 [PID wake up, feedb] Page Setting 2 [Communication] 0 [AI] 0 [Enable] 1 [PID by VIA] Factory value 1 0 0 0 0s 0.30 % In accordance with the application 0.20 0.00 0 0.2 Hz 0.0 Hz 0.0 Hz
77 90 108 110 111 110 110 111 111 111 111 111
44
S1A53838 09/2011
Overview
Drive Operation
Local and Remote Modes of Operation Overview The ATV212 drive has two modes of operation, local and remote. In local mode, the ATV212 drive can be operated only from the embedded display terminal or graphic display option:
z z
Use the RUN and STOP keys for command control Use the UP and DOWN keys for speed control
In remote mode, the ATV212 drive is operated from a combination of the command and speed reference sources defined by programming parameters [Frequency mode sel] (FMOd) and [Command mode sel] (CMOd) (see page 77). Command Sources The command source [Command mode sel] (CMOd) choices are:
z z z
External signals to the control terminal logic inputs F, R, RES and VIA Serial communication control (Modbus, Metasys N2, Apogee FLN P1, BACnet, or LonWorks) Embedded display terminal RUN and STOP keys or graphic display option
Speed Reference Sources The speed reference source [Frequency mode sel] (FMOd) choices are:
z z z z z
External signals to the control terminal analog inputs VIA or VIB (420 mA, 010 Vdc), External signals to the control terminal logic inputs assigned to +/- Speed Serial communication control (Modbus, Metasys N2, Apogee FLN P1, BACnet, or LonWorks) Embedded display terminal UP and DOWN keys or graphic display option
S1A53838 09/2011
45
Overview
Command Mode Selection and Priorities The diagram below illustrates the control inputs and selection logic which determine the source of the drive's start/stop and speed reference commands. Command and Reference Switching
Commands
CMOd
LOC REM
Communication
Communication
Switching FMOd / F207 {LIx = 38 or F200} active inactive
LOC
Cmd SetPoint
References
FMOd
VIA VIB
1 2
Communication
4
Communication
ON REM OFF Terminal Local Graphic display option LOC Speed SetPoint
5 Up/Down speed
F207
VIA
1
F807
RJ45 channel: Modbus Network channel: Paremeter F829
VIB 2
Terminal Local Graphic display option
3 4
Communication
Communication
Up/Down speed 5
Default value
Parameters [Command mode sel] (CMOd) and [Frequency mode sel] (FMOd) are the first layers of logic used by the drive to determine its command CMOd and speed reference FMOd source. [Remote spd ref 2] (F207) is a secondary speed reference source that may override the source selected by FMOd (see page 77). The speed reference source identified by F207 takes control if either:
z z
A logic input assigned to function 38 (frequency reference source switching) is enabled, or Parameter [Auto/man speed ref] (F200) is set to 1 and the drive's output frequency is equal to or less than 1 Hz (see page 108).
If a serial communication link is established, it can take control of the ATV212 drive, overriding inputs identified by CMOd, FMOd, and F207. Control is restored to CMOd, FMOd, and F207 only if:
z z
The serial communication link relinquishes control, or A logic input assigned to function 48 (forced local) is enabled.
The final layer of logic used by the drive to determine its command source is the LOC/REM key on the graphic display option. When the drive and embedded HMI is set to local mode (by pressing the LOC/REM key, lighting the local mode LED), the drive responds only to commands from the embedded and graphic display option.
46
S1A53838 09/2011
Overview
DANGER
UNINTENDED EQUIPMENT OPERATION z Know the state of the frequency and run commands from the remote source before exiting the local mode. z Upon entering the remote mode, the drive will respond to the most recent command from the remote source, even if it was received before entering or while in the local mode. Failure to follow these instructions will result in death or serious injury. Switching between local and remote mode is achieved with the LOC/REM key on the drives embedded display terminal or with F4 key on the graphic display option. The LOC/REM key can be disabled by setting parameter [Loc/rem key] (F732) to 1 (see page 80). When parameter [Switch rem/Local] (F295) is set to 1 (factory setting), a bumpless tranfer of motor operation is achieved when switching from remote to local mode (see page 78). For example, if the bumpless transfert feature is active and if the motor is running at full speed with the drive in remote mode, the motor will still run at full speed after the drive is transferred to local mode. Conversely, when switching from local to remote mode, the run and speed command is not transferred to the remote mode. Upon entering the remote mode, the drive will operate on the run and speed command set by the remote source even if it was received before entering or while in the local mode. The diagram below is an example timing diagram. Switching Between Local and Remote Mode
Remote mode
LOC REM
Local mode The remote run command and frequency command are transferred to the local mode when the LOC/REM key is pressed. In this example, the run command and frequency command from the remote mode are copied to the local mode, and the motor continues to run.
ON Key OFF
Output Frequency Local Run Command Remote Run Command Run Status ON OFF
Local mode
LOC REM
Remote mode When switching from the local mode to the remote mode, the run command and frequency command are determined by the setting in the remote mode. In this example, when the LOC/REM button is pressed, the motor in started. This is due to the application of a remote run command when the drive exits the local mode and enters the remote mode.
Output Frequency Local Run Command Remote Run Command Run Status
ON OFF
S1A53838 09/2011
47
Overview
Local Mode When the ATV212 drive is in local mode, the LED above the LOC/REM key is illuminated. On the graphic display option:
AUF: QUICK MENU LL: Low Limit frequency DEC: Deceleration time 1 ACC: Acceleration time 1 AU1: Auto ramp vLv: Motor rated voltage Loc Ref loc Cmd loc Loc/Rem
Starting and Stopping the Motor in Local Mode Start and stop the motor with the RUN and STOP keys on the graphic/embeded display terminals. The setting of parameter [Loc. mot stop mode] (F721) determines how the motor stops when the drive is in local mode (see page 78): If F721 is set to 0 (factory setting), the motor will stop on a ramp, based on the time value set in parameter [Deceleration time 1] (dEC) or parameter [Deceleration time 2] (F501). z If F721 is set to 1, power will be removed from the motor when the STOP key is pressed, allowing the motor to coast to a stop with the ramp-down time determined by inertia and friction. Use of the RUN and STOP keys in local mode can be disabled using parameter [Run/stop key] (F733) (see page 80).
z
Adjusting Motor Speed in Local Mode Set the motor speed using the UP and DOWN keys on the graphic/embeded display terminals. Motor speed can be adjusted while the drive is operating. Normally, motor frequency changes by 0.1 Hz each time the UP or DOWN key is pressed. This rate of speed change can be altered by entering a new frequency step change into parameter [Loc. speed ref. step] (F707) (see page 77). If the ENT key is pressed after the motor speed has been adjusted, that speed setpoint value will be entered into parameter FC. The next time the drive is started in the local mode, it will accelerate the motor directly to the speed setpoint memorized by [Local speed ref.] (FC) (see page 77). Selecting Motor Rotation Direction in Local Mode Motor rotation direction is set by parameter [Local mot. direction] (Fr) (see page 77). The four selections are: 0: Forward only (factory setting) 1: Reverse only z 2: Forward, with reverse selectable from the graphic/embeded display terminals (1) z 3: Reverse, with forward selectable from the graphic/embeded display terminals (1) (1)If Fr is set to either 2 or 3, motor rotation can be set to forward by pressing the UP key while holding the ENT key. Reverse can be set by pressing the DOWN key while holding the ENT key.
z z
Motor rotation is indicated on the embedded display terminal as Fr-F for forward and as Fr-r for reverse. The ability to run in the Forward or Reverse direction can be set with parameter [Motor direction] (F311) (see page 86).
48
S1A53838 09/2011
Overview
Resetting drive detected fault in Local Mode It is not possible to clear a drive detected fault if the cause of the detected fault persists. Be certain to diagnose and rectify the cause of the detected fault before attempting a drive reset. With the STOP Key To clear a drive detected fault in local mode: 1. Press the STOP key. See Fault detection codes that can be cleared with the automatic restart function after the cause has disappeared on page 124 for a list of detected faults that can be cleared with the STOP key. If it is possible to reset the drive, the embedded display terminal will display CLr. 2. To clear the detected fault, press the STOP key a second time. 3. If the cause of the detected fault is still present, the CLr display will not appear. Diagnose and clear the detected fault before attempting to reset the drive. Use of the STOP key as a clear detected fault can be set with parameter [HMI reset button] (F735) (see page 80). In the event of an OL1 or OL2 detected fault, the following time periods are necessary before a clear detected fault is possible:
z z
OL1 (drive overload)about 30 seconds after the detected fault has occured OL2 (motor overload)about 120 seconds after the detected fault has occured
By Cycling Line Power A drive detected fault can also be cleared by removing and restoring line power. Be certain that the cause of the detected fault is no longer present and leave power removed long enough for all of the LEDs on the face of the drive to extinguish. Cycling power to clear a detected fault can cause the detected fault history to be lost. Refer to parameter [Drive Fault Memory] (F602) on page 127. Logic Input Functions Active in Local Mode The logic input functions listed in the table below are active, even if [Command mode sel] (CMOd) is set to 1 (embedded display terminal control). See table on page 90 for logic input function settings.
Logic Input Function No. 1 54 10 55 11 45 16 38 41 42 43 44 46 47 51 52 53 62 64 Description [Run permissive] [Inverse Run permissive] [Fault reset] [Inv fault reset] [Ext Fault] [Inv Ext. fault] [Run reset] [Frequency source] [(+) speed] [(-) speed] [+/- clear] [+/- SPD, FLT CLR] [Ext. Th fault] [Inv Ext. Th fault] [Reset kWh] [Forced mode] [Fire mode] [RY on] [Cancel HMI cmd]
S1A53838 09/2011
49
Overview
Remote Mode When the ATV212 drive is in the remote mode, the LOC/REM LED is off. Starting and Stopping the Motor in Remote Mode The diagram on page 46 illustrates the start/stop command source when the drive is in remote mode. With Logic Input Terminals Use the logic input terminals F, R, RES, or VIA to start the drive if parameter [Command mode sel] (CMOd) is set to [Logic Inputs] (0) (factory setting). With the display terminals The drive responds to commands from the embedded display terminal or graphic display option, just as in local mode, if parameter [Command mode sel] (CMOd) is set to [HMI] (1). With Serial Communication The drive responds to commands sent over the serial communication link (Modbus, Metasys N2, Apogee FLN, BACnet or LonWorks) if parameter [Command mode sel] (CMOd) is set to [Communication] (2). The drive responds to commands sent over the RJ45 communication port if parameter [Com channel choice] (F807) is set to 0. Other protocols are available when F807 is set to 1 on open style port. With the graphic/embeded display terminals STOP Key The graphic/embeded display terminals STOP key is active when the drive is in remote mode. Pressing the STOP key causes the drive to stop according to the setting of parameters [Ext. fault stop Mode] (F603), [DC brk time ext flt] (F604), and [DC braking current] (F251) (see page 115 and page 88) . After the drive has come to a stop, the graphic/embeded display terminals display E and the fault relay is activated. Adjusting the Motor Speed in Remote Mode The diagram on page 46 illustrates the speed reference source when the drive is in remote mode. By Analog Input VIA A 010 Vdc or 420 mA signal connected to VIA and CC can be used to adjust the motor speed if:
z z
Parameter [Frequency mode sel] (FMOd) is set to 1 (factory setting). Alternate speed reference source parameter [Remote spd ref 2] (F207) has not been enabled (see page 78).
The analog signal type depends on the setting of switch SW100 and parameters F109, F201F204, and F470F471. By Analog Input VIB A 010 Vdc signal connected to VIB and CC can be used to adjust the motor speed if:
z z
Parameter [Frequency mode sel] (FMOd) is set to 2. Alternate speed reference source parameter [Remote spd ref 2] (F207) has not been enabled.
The control that VIB has over motor speed depends on the setting of switch SW100 and parameters F210 F213, F472F473, and F645.
50
S1A53838 09/2011
Overview
Parameter [Frequency mode sel] (FMOd) is set to 3. Alternate speed reference source parameter [Remote spd ref 2] (F207) has not been enabled.
By Serial communication control Serial communication control (Modbus, Metasys N2, Apogee FLN, BACnet or LonWorks) of the motor speed is enabled, if:
z z z z
Parameter [Com channel choice] (F807) is set to 0 (only for Modbus on RJ45 port), Parameter [Com channel choice] (F807) is set to 1, Parameter [Frequency mode sel] (FMOd) is set to 4. Alternate speed reference source parameter [Remote spd ref 2] (F207) has not been enabled.
By +/- Motor Speed Control +/- Motor speed control is enabled, if:
z z
Parameter [Frequency mode sel] (FMOd) is set to 5, Alternate speed reference source parameter [Remote spd ref 2] (F207) has not been enabled.
Selecting Motor Rotation Direction in Remote Mode The diagram on page 46 illustrates the motor rotation command source when the drive is in remote mode. With Logic Input Terminals Use the logic input terminals F, R, RES, or VIA to select motor rotation direction if parameter [Command mode sel] (CMOd) is set to 0 (factory setting). With the embedded display terminal or graphic display option Motor rotation direction can be set by pressing the display terminal UP and ENT keys if:
z z z
Parameter [Command mode sel] (CMOd) is set to 1, Serial communication control has not been established. Parameter [Local mot. direction] (Fr) is set to either 2 or 3.
With Serial Communication The drive responds to commands sent over the serial communication link (Modbus, Metasys N2, Apogee FLN, BACnet or LonWorks) if Parameter [Command mode sel] (CMOd) is set to 2. Resetting drive detected faults in Remote Mode The diagram on page 46 illustrates the clear detected fault command source when the drive is in remote mode. It is not possible to clear a drive detected fault if the cause of the detected fault persists. Be certain to diagnose and rectify the cause of the detected fault before attempting to reset the drive. See Automatically Resettable detected faults on page 124 for a list of detected faults that can be cleared in remote mode. With the Logic Input Terminals Use the logic input terminals F, R, RES, or VIA to clear a drive detected fault if parameter [Command mode sel] (CMOd) is set to 0 (factory setting). With the graphic/embeded display terminals The STOP key can be used to clear a drive detected fault if parameter [Command mode sel] (CMOd) is set to 1. To clear a drive detected fault, press the STOP key. If it is possible to reset the drive, it will display CLr. To clear the detected fault, press the STOP key a second time. If the cause of the interruption is still present, the CLr display will not appear. Diagnose and clear the detected fault before attempting to reset the drive. The use of the STOP key as a clear detected fault can be managed by parameter [HMI reset button] (F735).
S1A53838 09/2011
51
Overview
With Serial Communication A drive detected fault can be cleared over the serial communication link (Modbus, Metasys N2, Apogee FLN, BACnet or LonWorks) if parameter [Command mode sel] (CMOd) is set to 2. In the event of an OL1 or OL2 detected fault, the following time periods needs to pass before a clear detected fault is possible:
z z
OL1 (drive overload) - about 30 seconds after the occurrence of the event. OL2 (motor overload) - about 120 seconds after the occurrence of the event.
By Cycling Line Power A drive detected fault can also be cleared by removing and restoring line power. Be certain that the cause of the detected fault is no longer present and leave power removed long enough for all of the LEDs on the face of the drive to go out. Cycling power to clear a detected fault can cause the detected fault history to be lost. Refer to parameter F602 on page 127 for drive fault memory options.
52
S1A53838 09/2011
Programming
Programming
II
What's in this Part? This part contains the following chapters:
Chapter 3 4 5 6 7 8 9 10 11 12 13 Quick Menu Programming Parameters Motor Control Parameters Drive Control Parameters Application Parameters I/O Control Parameters Display Parameters Detected Fault Management Parameters Serial Communication Parameters Start/Stop Control By Speed Reference Level Droop Control Chapter Name Page
55
61 65 77 81 89 119 123 137 143 145
S1A53838 09/2011
53
Programming
54
S1A53838 09/2011
Quick Menu
Quick Menu
3
What's in this Chapter? This chapter contains the following topics:
Topic Quick menu Page 56
S1A53838 09/2011
55
Quick Menu
Quick menu
The AUF submenu provides ready access to the ten basic parameters commonly used in programming the drive. In many cases, programming the ATV212 drive is complete when these 10 parameters and motor parameters have been properly set. .
Code Name / Description Adjustment range Automatic ramp adaptation Factory setting 1
AU1
0 1 2
[Auto ramp]
[Disabled] [Enable]: [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC) [ACC only]: [Acceleration time 1] (ACC) only If parameter AU1 is set to 1 or 2, the drive will monitor its own loading level and optimize the acceleration and deceleration ramps. The acceleration and deceleration AU1 = 1 only rates will be automatically adjusted between 1/8 to 8 times the settings of ACC and dEC, depending on the drives current rating and the load level on the motor. ACC and dEC should be appropriately set for an average load in the application. If the load on the motor increases rapidly during ramp up or ramp down, the auto ramp adaptation feature may not help to prevent the drive from experiencing an overcurrent or overvoltage. If the application requires a consistent acceleration and deceleration time, set AU1 to 0, and set ACC and dEC manually as needed. The manual acceleration and deceleration times can still be overridden by the [Motor Current Limit] (F601) (see page 69) and [Overvoltage fault] (F305) (see page 128) and [Overvoltage level] (F626) (see page 128) functions.
ACC
[Acceleration time 1]
0.0 to 3200 s
The setting of parameter ACC determines the slope of the acceleration ramp and the time it takes for the output frequency of the drive to increase from 0 Hz to the setting of [Max frequency] (FH) (see page 82). If parameter [Auto ramp] (AU1) is set to 1 or 2, the acceleration ramp may be increased or decreased from the setting of ACC, depending on the amount of load on the motor during ramp up. If two different acceleration rates are needed, see parameter [Acceleration time 2] (F500) on page 83.
Output frequency (Hz)
Time (s)
dEC
[Deceleration time 1]
0.0 to 3200 s
The setting of parameter dEC determines the slope of the deceleration ramp and the time it takes for the output frequency of the drive to decrease from the setting of [Max frequency] (FH) to 0 Hz. If parameter [Auto ramp] (AU1) is set to 1 or 2, the deceleration ramp may be increased or decreased from the setting of dEC, depending on the amount of load on the motor during ramp down. See diagram above. If two different deceleration rates are needed, see parameter [Deceleration time 2] (F501) on page 83.
LL
0.0 Hz
Parameter LL sets the minimum frequency that can be commanded to the drive by the local or remote speed reference source.
UL
50.0 Hz
Parameter UL sets the maximum frequency that can be commanded to the drive by the local or remote speed reference source. The top end of its range is limited by the setting of [Max frequency] (FH). (1) See table page 167
56
S1A53838 09/2011
Quick Menu
Code
Name / Description
Adjustment range Motor Rated Current Overload Setting 10 to 100% of the drives output current rating
tHr
Set parameter tHr to the motors rated current as indicated on the motor nameplate for the selected operating voltage. If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter tHr will be adjusted in amperes. If parameter F701 is set to 0, parameter tHr will be adjusted in percentage. In this case, divide the motor rated current by the drive rated current (as listed on its nameplate) and set parameter tHr to the resulting percentage. The setting of parameter [Switch. freq. level] (F300) does not change the drives rated current for the sake of this calculation (see page 85).
FM
[AO scaling]
Parameter FM is used to match the FM terminal output signal with the input requirements of the attached panel meter by adjusting the slope and bias of the analog output signal. Before adjusting FM, set FMSL to either 15 or 17. As you adjust the value of FM, monitor the display on the attached panel meter. When the meter display reaches 100%, press the ENT key on the drive display terminal. The drive will flash between FM and the adjusted value, indicating that the adjustment has been saved.
Pt
0
[Constant V/Hz]: Constant V/Hz Use constant V/Hz mode for loads that require the same torque at low speeds as at rated speeds. Low speed torque can be adjusted manually by setting parameter [Motor Voltage Boost] (ub) (see page 68).
Motor rated voltage Output Voltage (%) Motor Voltage Boost
[Variable Torque]: Variable torque Use variable torque mode for loads such as centrifugal fans and pumps whose torque requirements increase as a square of the increase in motor speed. Low speed torque can be adjusted manually by setting parameter ub.
Motor rated voltage Output Voltage (%) Motor Voltage Boost
0
[Cst V/Hz+Boost]: Constant V/Hz with automatic torque boost See the diagram on page 66. This mode is similar to the constant V/Hz mode (for loads that require the same torque at low speeds as at rated speeds), except it automatically increases motor voltage and torque to compensate for increases in load. [SVC]: Sensorless vector control Use sensorless vector control mode to increase torque at motor speeds below 3 Hz or to improve speed regulation (0.5 to 1%). See diagram on page 66. [Economy]: Energy saving In energy savings mode, the ATV212 drive monitors motor loading and automatically modulates the voltage applied to the motor to optimize energy consumption. If the ATV212 drive and the connected motor have the same power rating, and if the motor has a nominal 1500 rpm rating, no motor auto-tuning is required to use this motor control mode. Otherwise, follow the steps outlined in Motor Tuning on page 70. [Do not use]: Reserved [Do not use]: Reserved
5 6
S1A53838 09/2011
57
Quick Menu
Code
Name / Description
uL
Set parameter uL (vL) to the motors rated frequency as indicated on the motor nameplate. Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the 50 Hz reset. For more information, see page 62.
uLu
Set parameter uLu (vLv) to the motors rated voltage as indicated on the motor nameplate. ATV212pppM3X: 50 to 330 V. ATV212pppN4: 50 to 660 V Note: Drive output voltage cannot be set to exceed the input line voltage level. (1) See table page 167
58
S1A53838 09/2011
Quick Menu
Motor parameters Configure the motor parameters and perform an auto-tuning ([Auto-tuning drive] (F400) = 2, see page 71 for auto-tuning).
Code Name / Description Adjustment range 0.1 to 200.0 A Factory setting According to drive rating (1)
F415
Set parameter F415 to the motor rated full load current in amperes as indicated on the motors nameplate.
F417
Set parameter F417 to the motor rated speed in rpm as indicated on the motors nameplate.
F601
110%
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE z Check that the motor will withstand this current. z Check that the profile mission complies with the derating curve given in the installation manual Failure to follow this instruction can result in equipment damage. Parameter F601 can be adjusted to limit current during motoring or braking. Display in Current Limit Mode: When the drive goes into current limit mode, it will: Adjust the output frequency to limit the flow of motor current (down when motoring, up when braking). Display the letter C and the output frequency flashing on the embedded software terminal, ex: If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter F601 will be adjusted in amperes. If parameter F701 is set to 0, parameter F601 will be adjusted as a percentage of the drives output rated current as listed on its nameplate. The setting of parameter [Switch. freq. level] (F300) (see page 85) does not change the drives rated current for the sake of this calculation. Do not set parameter F601 below the no-load current rating of the motor.
F400
DANGER
HAZARD OF ELECTRIC SHOCK OR ARC FLASH z During auto-tuning, the motor operates at rated current. z Do not service the motor during auto-tuning. Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL z It is essential that the following parameters uLu (vLv), uL (vL), F415 and F417 are correctly configured before starting auto-tuning. z When one or more of these parameters have been changed after auto-tuning has been performed, F400 will return 0 and the procedure will have to be repeated. Failure to follow these instructions can result in death or serious injury. 0 1 2 [Disabled]: Disabled [Initialize constant] (2): Auto-tuning is performed immediatly if possible. Parameter Auto Torque Boost [Auto Torque Boost] (F402) may need adjustment [Complete tune] (2): complete auto tuning (1) See table page 168. (2) Parameter F400 is reset to 0 after the auto tuning is performed.
S1A53838 09/2011
59
Quick Menu
60
S1A53838 09/2011
Programming Parameters
Programming Parameters
4
What's in this Chapter? This chapter contains the following topics:
Topic Parameter Reset Macro Programming (AU4) Parameter Lock Display of Submenu AUF (F738) Page 62 63 64 64
S1A53838 09/2011
61
Programming Parameters
Parameter Reset
Parameter Reset Options The ATV212 drive offers three options to return parameters to their factory default settings:
z z z
Factory reset: set parameter [Parameter reset] (tYP) to 3 50 Hz reset: set parameter [Parameter reset] (tYP) to 1 60 Hz reset: set parameter [Parameter reset] (tYP) to 2
Factory setting 0
Code
Name / Description
tYP
[Parameter reset]
DANGER
UNINTENDED EQUIPMENT OPERATION When tYP is set to 3 or 8: - Check that the modification of the current configuration is compatible with the wiring diagram used. - All logic inputs must be deactivated to avoid unintended restart. Failure to follow these instructions will result in death or serious injury. 0 1 [No action] [50 Hz reset]: 50 Hz parameter reset Setting parameter tYP to a value of 1 will set specific parameters to values suitable for many 50 Hz (motor base frequency) applications. See Parameters whose values after a reset vary by reset type table on page 166 and table on page 168 for a list of parameters that are affected by this reset action and their resultant values. [60 Hz reset]: 60 Hz parameter reset Setting parameter tYP to 2 sets specific parameters to values suitable for many 60 Hz (motor base frequency) applications. See table "Parameters whose values after a reset vary by reset type" on page 166 and table "Parameters whose values after a reset are drive model dependant but do not vary by reset type" on page 167 for a list of parameters that are affected by this reset action and their resultant values. [Factory set]: Factory reset Setting parameter tYP to 3 resets most parameters to their factory settings. See tables listed below for a listing of the values that will be copied into the drive by this factory reset action: Parameters whose values after a reset do not vary by reset type (on page 162). Parameters whose values after a reset vary by reset type (on page 166). Parameters whose values after a reset are drive model dependant but do not vary reset type (on page 167). Parameters whose values after a reset are drive model and reset type dependant (on page 168). Parameters whose values do not change if a reset is performed (on page 169). A factory reset will also clear the detected fault history. [Trip cleared]: detected fault history cleared Setting parameter tYP to 4 clears the detected fault history. As soon as the detected fault history is reset, parameter tYP resumes its default value of 0. [Cumul time clear]: Elapsed Motor Run Time Reset Setting parameter tYP to 5 resets the elapsed motor run time clock. As soon as the elapsed motor run time clock is reset, parameter tYP resumes its default value of 0. [EtYP fault reset]: Clear EtYP detected fault Setting parameter tYP to 6 clears a EtYP detected fault. As soon as the EtYP detected fault is cleared, parameter tYP resumes its default value of 0. [Save parameters]: Save user-defined settings The drive parameter settings can be stored into memory into the drive as a custom parameter set. Set parameter tYP to 7 to save the current drive parameter settings to memory [Recall parameters]: Recalls user-defined settings The drive parameter settings can be reloaded into the drive as a custom parameter set. Set parameter tYP to 8 to reload into the drive the parameter settings last saved by setting tYP to 7. [Elapse time reset]: Elapsed drive run time reset Setting parameter tYP to 9 resets the elapsed drive run time clock. As soon as the elapsed motor run time clock is reset, parameter tYP resumes its default value of 0.
62
S1A53838 09/2011
Programming Parameters
AU4
DANGER
UNINTENDED EQUIPMENT OPERATION Check that the selected macro configuration is compatible with the wiring diagram used. Failure to follow these instructions will result in death or serious injury. 0 [Factory set] Command reference: logic inputs (CMOd = 0). See page 77. Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1, F201 = 0). See [Frequency mode sel] (FMOd) page 77 and Analog Input Speed Reference page 106. F: run forward (F111 = 2). See F Logic Input Function page 90. R: preset speed 1 (F112 = 6). See R Logic Input Function page 90. RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90. Drive ready for operation (F110 = 1). See Active Logic Function 2 page 112. [Run permissive] Command reference: logic inputs (CMOd = 0). See page 77. Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1). See [Frequency mode sel] (FMOd) page 77. F: run forward (F111 = 2). See F Logic Input Function page 90. R: run permissive (F112 = 1). See R Logic Input Function page 90. RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90. [3-wire] Command reference: logic inputs (CMOd = 0). See page 77. Speed reference: analog input VIA = 010 V or 020 mA (FMOd = 1). See See [Frequency mode sel] (FMOd) page 77. F: run forward (F111 = 2). See F Logic Input Function page 90. R: stop ramp (F112 = 49). See R Logic Input Function page 90. RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90. [+/- Speed] Command reference: logic inputs (CMOd = 0). See page 77. Speed reference: +/- Speed (FMOd = 5). See See [Frequency mode sel] (FMOd) page 77 F: run forward (F111 = 2). See F Logic Input Function page 90. R: + Speed (F112 = 41). See R Logic Input Function page 90. RES: - Speed (F113 = 42). See RES Logic Input Function page 90. [4-20 mA speed ref] Command reference: logic inputs (CMOd = 0). See page 77. Speed reference: analog input VIA = 420 mA (FMOd = 1, F201 = 20). SeeSee [Frequency mode sel] (FMOd) page 77 and Analog Input Speed Reference page 106. F: run forward (F111 = 2). See F Logic Input Function page 90. R: preset speed 1 (F112 = 6). See R Logic Input Function page 90. RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90. (1) When programming parameter AU4, the embedded display terminal will display two numbers. The left number is the value last entered into AU4. The right number will be 0. Use the UP/DOWN keys to change the right number to the desired value and press ENT. Entering 0 into AU4 has no effect on the drive. Programming 0 into AU4 will not return the seven parameters to their factory default values.
S1A53838 09/2011
63
Programming Parameters
Parameter Lock
Code Name / Description Factory setting 0
F700
0
[Parameter lock]
[Unlocked]: All parameters are unlocked and can be changed. See table on page 37 for the parameters that cannot be changed while the drive is running. [Locked]: Only parameter F700 can be changed.
F738
0 1
The setting of this parameter determines whether the AUF submenu, Quick Menu, will be displayed on the HMI (see page 30). [AUF displayed]: AUF parameter displayed [AUF hidden]: AUF parameter hidden
64
S1A53838 09/2011
5
What's in this Chapter? This chapter contains the following topics:
Topic Motor Control Mode Other Motor Control Mode Parameters Motor Tuning Auto-tuning Expert parameters Supply Voltage Correction and Motor Voltage Limitation Motor 2 Control Parameters Page 66 68 70 71 72 73 74
S1A53838 09/2011
65
0
Motor Rated Frequency Output Frequency (Hz)
Sensorless Vector Control Mode ([Mot cont. mode sel.] (Pt) = 3) Sensorless vector control mode is only for use in applications where:
z z z
Each motor is powered by its own ATV212 drive (not for multi-motor applications). The motor has a power rating equal to that of the ATV212 drive, or no lower than one hp rating less. The motor has between two and eight poles (750 to 3000 rpm).
Sensorless vector control will not improve motor control above the motors rated speed. Sensorless vector control is more effective if the motor leads are less than 30 m (100 ft) in length. If motor leads longer than 30 m (100 ft) are required, perform an auto-tuning with the long motor leads included in the circuit. Motor torque may not be maximized at the motors rated frequency due to voltage drop in the motor leads. Connecting a load reactor or a motor filter on the output of the ATV212 drive may reduce the torque generated by the motor in sensorless vector control mode. Auto-tuning will most likely not be possible with a reactor or filter attached to the drive. Manual tuning will be required
66
S1A53838 09/2011
Code
Name / Description
Pt
0
[Constant V/Hz]: Constant V/Hz Use constant V/Hz mode for loads that require the same torque at low speeds as at rated speeds. Low speed torque can be adjusted manually by setting parameter [Motor Voltage Boost] (ub) (see page 68).
Motor rated voltage Output Voltage (%) Motor Voltage Boost
[Variable Torque]: Variable torque Use variable torque mode for loads such as centrifugal fans and pumps whose torque requirements increase as a square of the increase in motor speed. Low speed torque can be adjusted manually by setting parameter ub.
Motor rated voltage Output Voltage (%) Motor Voltage Boost
0
[Cst V/Hz+Boost]: Constant V/Hz with automatic torque boost See the diagram on page 66. This mode is similar to the constant V/Hz mode (for loads that require the same torque at low speeds as at rated speeds), except it automatically increases motor voltage and torque to compensate for increases in load. [SVC]: Sensorless vector control See the diagram on page 66. Use sensorless vector control mode to increase torque at motor speeds below 3 Hz or to improve speed regulation (0.5 to 1%). [Economy]: Energy saving In energy savings mode, the ATV212 drive monitors motor loading and automatically modulates the voltage applied to the motor to optimize energy consumption. If the ATV212 drive and the connected motor have the same power rating, and if the motor has a nominal 1500 rpm rating, no motor auto-tuning is required to use this motor control mode. Otherwise, follow the steps outlined in Motor Tuning on page 70. [Do not use]: Reserved [Do not use]: Reserved
5 6
S1A53838 09/2011
67
uL (vL) [Motor rated freq.] uLu [Motor rated voltage] ub [Mot Voltage Boost] F170 [Mot 2 rated Freq.] F171 [Motor 2 rated Volt] F172 [Motor 2 Volt Boost] F400 [Auto-tuning drive] F401 [Slip Compensation] F402 [Auto Torque Boost] F415 [Motor rated current] F416 [Mot no-load current] F417 [Motor rated speed] F418 [Frequency loop gain] F419 [Freq. loop stability] F480 [No load cur. coef] F485 [Stall control coef. 1] F492 [Stall control coef. 2] F494 [Mot. adj coefficient] F495 [Motor voltage coef.] F496 [PWM adj. coef.]
X: Not applicable for the [Mot cont. mode sel.] (Pt) setting
: Adjustment of this parameter is required.
Code
Name / Description
ub
Low speed motor torque can be adjusted with parameter ub when parameter [Mot cont. mode sel.] (Pt) (see page 67) is set to 0 (Constant V/Hz) or 1 (Variable Torque). See curves on page 66 for more information. If nuisance overcurrent faults occur during starting, reducing the setting of parameter ub may help. (1) See table page 167.
68
S1A53838 09/2011
Code
Name / Description
F601
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE z Check that the motor will withstand this current. z Check that the profile mission complies with the derating curve given in the installation manual Failure to follow this instruction can result in equipment damage. Parameter F601 can be adjusted to limit current during motoring or braking. Display in Current Limit Mode: When the drive goes into current limit mode, it will: Adjust the output frequency to limit the flow of motor current (down when motoring, up when braking). Display the letter C and the output frequency flashing on the embedded software terminal, ex: If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter F601 will be adjusted in amperes. If parameter F701 is set to 0, parameter F601 will be adjusted as a percentage of the drives output rated current as listed on its nameplate. The setting of parameter [Switch. freq. level] (F300) (see page 85) does not change the drives rated current for the sake of this calculation. Do not set parameter F601 below the no-load current rating of the motor.
S1A53838 09/2011
69
Motor Tuning
Tuning the drive to specific motor values will optimize motor performance if parameter [Mot cont. mode sel.] (Pt) (see page 67) is set to:
z z z
2 (constant V/Hz with automatic boost), 3 (sensorless vector control), or 4 (energy savings)
At a minimum, manually set parameters uL (vL), uLu (vLv), F415, F416, and F417. Parameters [Slip Compensation] (F401), [Auto Torque Boost] (F402), [Frequency loop gain] (F418) and [Freq. loop stability] (F419) can be set manually or they can be set automatically using the auto tuning function, parameter [Auto-tuning drive] (F400). More precise motor control adjustments can be made with parameters F307, F480, F485, F492, and F494 F496.
Code Name / Description Adjustment range According to drive rating (1) Factory setting According to drive rating (1)
uLu
Set parameter uLu (vLv) to the motors rated voltage as indicated on the motor nameplate. ATV212pppM3X: 50 to 330 V. ATV212pppN4: 50 to 660 V Note: Drive output voltage cannot be set to exceed the input line voltage level.
uL
25.0 to 200.0 Hz
50.0 Hz
Set parameter uL(vL) to the motors rated frequency as indicated on the motor nameplate. Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the 50 Hz reset. For more information, see page 62.
tHr
100%
Set parameter tHr to the motors rated current as indicated on the motor nameplate for the selected operating voltage. If parameter [Unit value selection] (F701) is set to 1 (see page 120), parameter tHr will be adjusted in amperes. If parameter F701 is set to 0, parameter [Motor thermal prot.] (tHr) will be adjusted in percentage. In this case, divide the motor rated current by the drive rated current (as listed on its nameplate) and set parameter tHr to the resulting percentage.
The setting of parameter [Switch. freq. level] (F300) does not change the drives rated current for the sake of this calculation (see page 85).
F607
10 to 2400 s
300 s
CAUTION
RISK OF DAMAGE TO THE MOTOR Check that the motor will withstand this time without overheating Failure to follow this instruction can result in equipment damage.
Parameter F607 determines how long the drive will support a 150% motor overload before a fault detection occurs.
F415
0.1 to 200.0 A
Set parameter F415 to the motor rated current in amperes as indicated on the motors nameplate.
F416
10.0 to 100.0%
Set parameter F416 to the ratio of the motors no load current to its rated current.
F417
Set parameter F417 to the motor rated speed in rpm as indicated on the motors nameplate.
(1) See table page 167.
70
S1A53838 09/2011
Auto-tuning
Before performing an auto-tune, verify that:
z z z z z z z z z z
A motor is connected and any load-side disconnect is closed. The motor is completely stopped and de-energized. The motor should be cool (room temperature). There is only one motor connected to the drive. All of the motor leads that will be used in the final installation are included in the output circuit during the autotuning process. Motor leads are no longer than 30 m (100 ft). Motor leads longer than 30 m (100 ft) may result in reduced motor torque and less than optimal motor control. No load reactors or filters are included in the motor circuit. Output reactors and filters may cause an autotuning detected fault Etn1 and reduce effectiveness of sensorless vector control. The motor is not more than 1 hp size smaller than the drive. The motor has at least 2 and not more than 8 poles (750 to 3000 rpm). The motor does not have a high slip rating.
Auto tuning is performed upon the first start command after parameter [Auto-tuning drive] (F400) below is set to 1 or 2 and is normally completed within 3 seconds. During the auto-tuning process, the graphic display option displays Atn1. During the auto-tuning process voltage is applied to the motor, although it barely rotates and produces very little torque. During the auto-tuning process, the drive checks for an output phase loss detection regardless of the setting of parameter F605. An output phase loss detection EPH0 will abort the auto-tuning process. If the auto-tuning process is unsuccessful, the drive will display Etn1. In this event, no results of the aborted auto-tuning 1 will be saved in the drive, and a manual tuning of parameters [Slip Compensation] (F401), [Auto Torque Boost] (F402), [Frequency loop gain] (F418) and [Freq. loop stability] (F419) will be required.
Code
Name / Description
Adjustment range -
Factory setting 0
F400
[Auto-tuning drive]
DANGER
HAZARD OF ELECTRIC SHOCK OR ARC FLASH z During auto-tuning, the motor operates at rated current. z Do not service the motor during auto-tuning. Failure to follow these instructions will result in death or serious injury.
WARNING
LOSS OF CONTROL z It is essential that the following parameters uLu, uL, F415 and F417 are correctly configured before starting autotuning. z When one or more of these parameters have been changed after auto-tuning has been performed, F400 will return 0 and the procedure will have to be repeated. Failure to follow these instructions can result in death or serious injury. 0 1 2 Auto tuning enable [Disabled] [Initialize constant]: Auto-tuning is performed immediatly if possible. Application of individual settings of Auto Torque Boost [Auto Torque Boost] (F402) [Complete tune]: Complete auto tuning. Parameter F400 is reset to 0 after the auto tuning is performed.
S1A53838 09/2011
71
Expert parameters
Code Name / Description Adjustment range Lower Limit function for Over Current Prevention 0.0 - UL Factory setting 0.0
F390
In the present software, motor speed is decreased to 0Hz in case the stall prevention state is continued. When motor speed is lower than F390 during stall prevention, motor speed is kept to F390 to increase motor current. In this situation, motor current is beyond stall prevention level (F601 or F185), therefore over current or over load detected fault may occur in some case.
Output Frequency (Hz)
Frequency command
F390
0 Time ON RUN command (F or R) OFF ON Over current alarm status OFF
F480
100 to 130%
100%
Use parameter F480 to fine tune motor torque during low-speed operation. To increase motor torque in the low-speed operating range, increase the setting of parameter F480. However, only adjust parameter F480 if an auto tune does not yield sufficient low-speed torque. Increasing the setting of parameter F480 may increase the motors no-load current during low-speed operation. Do not set this parameter so that the motors no-load current exceeds its rated operating current.
F485
10 to 250
100
Use parameter F485 to adjust the drives response to large, sudden changes in load when the motor is operated above its rated frequency. If a sudden change in load causes the motor to stall before the drive goes into current limit, gradually reduce the setting of F485.
F492
50 to 150
100
Use parameter F492 to adjust the drives response to a drop in the line supply voltage when the motor is operated above its rated frequency. Such a drop in voltage often causes fluctuations in motor current or vibration in the motor. To reduce these disturbances, set parameter F492 to a value between 80 and 90. Note: Reducing the F492 setting increases the motor running current level.
F494 F495
90 to 120%
104%
Use parameter F495 to limit the drives maximum output voltage. Increasing this setting increases torque when the motor is operated above its rated frequency, but may also cause motor vibration. Do not increase the value of F495 if motor vibrations occur.
F496
14.0 kHz
Adjusting the value of parameter F496 may reduce motor noise and vibration during PWM waveform frequency shifts in the mid-speed operating range.
72
S1A53838 09/2011
If the drives voltage output will be corrected for fluctuations in the line supply voltage, or If the drives voltage output will be limited, despite increases in the line supply voltage.
The drives output voltage will not exceed the input supply voltage. If parameter F307 is set to 0 or 2, no corrections are made in the motor voltage gating process in response to fluctuations in supply voltage. As a result, the V/Hz value of the output waveform to the motor will change in proportion to the input voltage. Conversely, if F307 is set to 1 or 3, the V/Hz value of the output waveform will be held constant, despite changes in the supply voltage level. If parameter F307 is set to 0 or 1, output motor voltage will be limited to the value set by parameter [Motor rated voltage] (uLu) (see page 70), even if the input supply voltage rises. If F307 is set to 2 or 3, output motor voltage can rise above the level set by uLu if the input supply voltage rises above the motor rated voltage. If parameter [Mot cont. mode sel.] (Pt) is set to a value of 2, 3, 4, 5, or 6, the supply voltage is corrected, regardless of the setting of parameter F307. The diagrams below illustrate the impact of each setting of parameter F307.
Supply Voltage uncorrected, Motor Voltage Limited
F307 = 0
F307 = 1
Input Voltage
High
Low
Low
Output Frequency
Output Frequency
F307 = 2
F307 = 3
Low
Low
Output Frequency
Output Frequency
Code
Name / Description
F307
0 1 2 3
[Motor volt limit]: Supply voltage uncorrected motor voltage limited [Line&mot correct.]: Supply voltage corrected motor voltage limited [No action]: Supply voltage uncorrected motor voltage unlimited [U Line correction]: Supply voltage corrected motor voltage unlimited
S1A53838 09/2011
73
F170
Set parameter F170 to the motors rated frequency as indicated on the motor nameplate. Note: It is possible to set the drives various motor control frequencies to 50 Hz by setting [Parameter reset] (tYP) to 1, the 50 Hz reset. For more information, see page 62.
F171
Set parameter F171 to the motors rated voltage as indicated on the motor nameplate. ATV212pppM3X: 50 to 330 V. ATV212pppN4: 50 to 660 V Note: Drive output voltage cannot be set to exceed the input line voltage.
F172
0 to 30%
F173
[Motor 2 Overload]
100%
Set parameter F173 to the motors rated current as listed on the motor nameplate for the selected operating voltage.
F185
110%
CAUTION
RISK OF DAMAGE TO THE MOTOR AND THE DRIVE z Check that the motor will withstand this current. z Check that the profile mission complies with the derating curve given in the installation manual. Failure to follow this instruction can result in equipment damage. Adjust parameter F185 to limit current during motoring or braking. Do not set parameter F185 below the no-load current rating of the motor; otherwise, the drive will determine that motor braking is taking place and will increase the frequency applied to the motor.
F401
[Slip Compensation]
0 to 150%
50%
Before adjusting parameter F401, verify that parameter [Motor rated speed] (F417) (see page 70) is set to the rated speed of the motor in rpm. Parameter F401 can be used to fine tune the drives slip compensation feature. Increasing the value of parameter F401 increases the drives compensation of motor slip.
F402
0.0 to 30.0%
74
S1A53838 09/2011
Code
Name / Description
Factory setting 40
F418
Parameters F418 and [Freq. loop stability] (F419) reduce the speed of the drives response to a change in speed command. The factory setting of these two parameters assumes that the inertia of the load is three times as large as that of the motor shaft. Adjust these two parameters if the factory setting is not appropriate for the application. Note: It is possible for the drives output frequency to exceed its upper limit (parameter [Max frequency] (FH)) if the acceleration parameter (ACC or F507) is set to its minimum value. Increasing the setting of parameter F418 reduces the drives response time to changes in the speed reference.
F419
1 to 100
20
Increasing the setting of parameter F419 further reduces the drives response to changes in the speed reference.
S1A53838 09/2011
75
76
S1A53838 09/2011
6
Code Name / Description Adjustment range Remote Mode Start/Stop Control Factory setting 0
CMOd
0 1 2
The setting of parameter CMOd determines the source of start, stop, forward, and reverse operation commands when the drive is in remote mode. The drive needs to be stopped to make changes to parameter CMOd. See diagram on page 46 and description page 50 for more information on the source of the drives operation commands. [Logic inputs]: Control terminal logic inputs [HMI]: Graphic display option [Communication]: Serial communication
FMOd
1 2 3 4 5
The setting of parameter FMOd determines the source of the drives speed reference when the drive is in remote mode. The drive needs to be stopped to make changes to parameter FMOd. See diagram on page 46 and description page 50 for more information on the source of the drives speed reference. [Ref source VIA]: VIA [Ref source VIB]: VIB [HMI reference]: Graphic display option [Serial com ref.]: Serial communication [+/- Speed]: +/- Speed
FC
LL - UL
0.0 Hz
The speed reference set by the UP/DOWN keys in local mode will be stored in parameter FC when the ENT key is pressed. The next time the drive is started in local mode, it will accelerate the motor directly to the speed setpoint memorized by FC.
Fr
0 1 2 3
[Run FW]: Run forward only. [Run rev.]: Run reverse only. [Run FW+rev]: Run forward with reverse selectable. [Run rev+FW]: Run reverse with forward selectable. If Fr is set to 2 or 3: The motor direction can be changed in local mode to forward by pressing the UP key while holding the ENT key and to reverse by pressing the DOWN key while holding the ENT key. The new motor direction will be displayed (forward = Fr-F, reverse = Fr-r) before the motor direction is reversed. The motors last operating direction in local mode will be stored before a power removal or loss detection. When power is restored to the drive, the local mode motor rotation direction will be the same as before the power loss detection. If [Switch rem/Local] F295 (see page 78) is enabled and control is transferred from remote to local mode, the local mode operation will assume the same motor rotation direction as in remote mode, regardless of the setting of Fr.
F707
0 1
0.0 Hz
[Disable]: Disabled (0.00). [Enable]: Enabled (0.01 to Maximum Frequency [Max frequency] (FH) in Hz). If parameter F707 is disabled in local mode, the drives speed reference will change in steps of 0.1 Hz each time the UP or DOWN key is pressed. If parameter F707 is enabled in local mode, the drives speed reference will change in steps equal to the setting of F707 each time the UP or DOWN key is pressed. Enabling parameter F707 only affects drive operation if parameter [Customized freq val] (F702) is set to 0.00. See page 121. If the display flashes HI or LO, it indicates that repeated usage of the UP or DOWN keys has caused to drives speed reference to reach either the [Low limit frequency] (LL) (see page 82) or the [Upper limit freq] (UL) (see page 82). This may happen if parameter F707 is set to a value larger than 0.00 Hz.
S1A53838 09/2011
77
Code
Name / Description
Factory setting 0
F721
The setting of parameter F721 determines the type of motor stop that will be executed when then embedded display terminal STOP key is pressed. The RUN and STOP keys needs to be enabled be setting parameter [Run/stop key] (F733) (see page 80) to 0 for the motor to stop when the embedded display terminal STOP key is pressed. 0 1 [Ramp stop]: Ramp stop [Freewheel]: Freewheel stop
F295
[Switch rem/Local]
If parameter F295 is enabled, the speed reference, run and direction commands will be transferred from remote to local mode when the LOC/REM key is pressed. Operation of the drive is not affected by a remote to local control mode transition. If parameter F295 is disabled, a remote to local control mode transition will cause the drive to remove power from the motor. A new run command and speed reference will need to be entered in the local mode. Regardless of the setting of parameter F295, a local to remote transition will cause the drive to immediately respond to the remote commands present at the moment of the transition. 0 1 [No bumpless]: Bumpless disabled [Bumpless]: Bumpless enabled
F256
0 1
0.0 to 600 s
0.0 s
[Disable]: (0.0) [Enable]: (0.01 to 600 seconds) If parameter F256 is enabled and if the drive operates continuously at [Low limit frequency] (LL) (see page 82) for a time period equal to the setting of F256, the drive will ramp the motor to a stop. While the motor is stopped, LStP will flash on the drive embedded display terminal. When the speed reference to the drive exceeds the low speed level LL+F391, the drive will accelerate the motor to the new speed reference. If parameter F256 is enabled, drive operation at or below the low speed level is also monitored during startup or during reversing of the motor. See diagram below.
F207
1 2 3 4 5
Parameter [Remote spd ref 2] (F207) defines the remote mode secondary speed reference source. The setting of parameter [Auto/man speed ref] (F200) (see page 108) determines whether this source is used for the speed reference. If F200 is set to 0, a logic input terminal set to function 38 (see page 108) determines if [Remote spd ref 2] (F207) identifies the speed reference source. If F200 is set to 1, [Remote spd ref 2] (F207) is the speed reference source when the drives output frequency is 1 Hz or below. See diagram on page 46 for more detail.
78
S1A53838 09/2011
Code
Name / Description
Adjustment range -
Factory setting 0
F650
WARNING
LOSS OF CONTROL The value of F650 will impact the direction of the motor. - Check wiring motor power UVW is correct. - Verify that the value of F650 is convenient for this application. Failure to follow these instructions can result in death, serious injury, or equipment damage. 0 1 2 [Disable] [Enable forward] [Enable Reverse] To enable Forced fire control, set parameter F650 to1 or 2 and assign a logic input to function 52 or 53 (see page 94). When parameter F650 is set to1 or 2, the embedded display will briefly flash the code FIrE. If parameter F650 is set to1 or 2 and a logic input assigned to function 52 or 53 is activated, the drive will run at the frequency set by parameter [Forced speed freq.] (F294) (see below). Note: First set [Motor direction] (F311) page 86 to allow forward or reverse operation. Push the ENT button for 2 sec to complete the setting. See F659 for more information of the behavior.
F659
0
[Enable transition] When parameter F659 is set to 0, the function is enabling on transition 0 -->1 of the logic input. The transition 1 -->0 will not disable the function.
WARNING
LOSS OF CONTROL If the Forced fire mode on logic input (function 52) has been enabled and F659 is set to 0, the drive will run and only removing power from the drive will stop it. If the Fire mode on logic input (function 53) has been enabled and F659 is set to 0, the drive will run and only removing power from the drive or a fault detection or a pressing on the STOP key on the display terminal will stop the drive. Check that this value of F659 is convenient for the application. Failure to follow these instructions can result in death, serious injury, or equipment damage. 1 [Enable level 1] When parameter F659 is set to 1, if the logic input is set to 0 the function is disabled. If the logic input is set to 1 the function is enable
WARNING
RISK OF APPLICATION MALFUNCTION When F659 is set to 1 for safety reason, the forced mode will be inhibited if the logic input is inactivated for any reason (order removed, input broken, wiring contact lost). - Check that this value of F659 is conveniant for the application. - If you need to continue to run if forced mode in any circonstance, select an other value of F659. Failure to follow these instructions can result in death, serious injury, or equipment damage. 2 [Enable level 0] When parameter F659 is set to 2, if the logic input is set to 1 the function is disabled. If the logic input is set to 0 the function is enable.
DANGER
UNINTENDED EQUIPMENT OPERATION When F659 is set to 2 for safety reason, the motor will run at Forced speed F294 in case of intempestive wire disconnection. - Check and control the wiring connection periodically. - Protect the signal conductors against damage that could result in unintentional conductor grounding. Failure to follow these instructions will result in death or serious injury.
F294
LL - UL
50.0 Hz
The F294 parameter is used to set the fixed frequency command for the drive when it is in Forced or Fire mode.
S1A53838 09/2011
79
Code
Name / Description
Adjustment range
Factory setting 0
F730
0 1
The setting of parameter F730 determines whether it is possible to set the drives speed by means of the embedded display terminal in local mode. [Enable] [Disable]
F732
[Loc/rem key]
Use parameter F732 to enable or disable the LOC/REM key on the drive embedded display terminal. If the LOC/REM key is disabled, switching between local and remote mode can be achieved with parameters [Frequency mode sel] (FMOd) and [Command mode sel] (CMOd). See page 77. 0 1 2 [Permitted memo]: still retained with the power off. [Prohibited] [Permitted no memo]: cancelled with the power off.
F733
0 1
[Run/stop key]
[Enable] [Disable]
The setting of parameter F733 determines whether it is possible to start and stop the drive by the Run/Stop keys located on the drive and graphic display option.
F734
[Priority stop]
WARNING
LOSS OF CONTROL You are going to disable the stop button located on the drive and graphic display option Do not select 1 unless exterior stopping methods exist. Failure to follow these instructions can result in death, serious injury, or equipment damage. The setting of parameter F734 determines whether it is possible to stop the drive by the Stop key located on the drive and graphic display option. 0 1 [Enable] [Disable]
F735
The setting of parameter [HMI reset button] (F735) determines whether it is possible to clear a drive detected fault by means of the embedded display terminal STOP key (see page 51 for more detail). 0 1 [Enable] [Disable]
80
S1A53838 09/2011
Application Parameters
Application Parameters
7
What's in this Chapter? This chapter contains the following topics:
Topic Skip Frequencies DC Injection Braking Parameters Page 87 88
S1A53838 09/2011
81
Application Parameters
Application parameters
Code Name / Description Adjustment range Maximum Frequency 30.0 Hz to 200.0 Hz Factory setting 50.0 Hz
FH
[Max frequency]
The setting of parameter FH determines the maximum output frequency of the drive. FH limits the setting of parameter [Upper limit freq] (UL) (see page 82), which can be adjusted while the drive is operating. Acceleration and deceleration rates are also affected by the setting of FH, as the definition of [Acceleration time 1] (ACC) or [Deceleration time 1] (dEC) (see page 83) is the time it takes for the drive to ramp the motor up or down between zero speed and the setting of FH. FH can only be adjusted while the drive is stopped.
Output frequency (Hz) Output frequency (Hz)
Speed Reference
100%
UL
High speed
50.0 Hz
Parameter UL sets the maximum frequency that can be commanded to the drive by the local or remote speed reference source. The top end of its range is limited by the setting of Maximum frequency [Max frequency] (FH). See diagram above.
LL
Low speed
0.0 Hz
Parameter LL sets the minimum frequency that can be commanded to the drive by the local or remote speed reference source. See diagram above.
F240
0.5 to 10.0 Hz
0.5 Hz
The setting of parameter F240 determines the drives output frequency at the moment it receives a start command. There is no acceleration time to reach the parameter F240 level. Parameter F240 is typically set for the rated slip frequency of the motor. This allows motor torque to be generated as soon as a start command is given. Adjust parameter F240 when a delay in the motors response to a start command adversely affects the application. To determine the motors slip frequency: 1) Subtract the motors rated speed at full load from its no-load speed (in rpm). 2) Divide the result by the no-load speed. 3) Multiply this result by the motors rated frequency in Hz. Example: Motor no-load speed = 1500 rpm Motor rated speed at full load = 1450 rpm Motor rated frequency = 50 Hz 1500 rpm 1450 rpm = 50 rpm 50 rpm / 1500 rpm = 3.33% 50 Hz x 0.0333 = 1.7 Hz (motor slip frequency)
82
S1A53838 09/2011
Application Parameters
Code
Name / Description
ACC
[Acceleration time 1]
The setting of parameter ACC determines the slope of the acceleration ramp and the time it takes for the output frequency of the drive to increase from 0 Hz to the setting of [Max frequency] (FH) (see page 82). If parameter [Auto ramp] (AU1) (see page 85) is set to 1 or 2, the acceleration ramp may be increased or decreased from the setting of ACC, depending on the amount of load on the motor during ramp up. If two different acceleration rates are needed, see parameter [Acceleration time 2] (F500) on page 83.
Output frequency (Hz)
Time (Sec)
dEC
[Deceleration time 1]
0.0 to 3200 s
The setting of parameter dEC determines the slope of the deceleration ramp and the time it takes for the output frequency of the drive to decrease from the setting of [Max frequency] (FH) to 0 Hz. If parameter [Auto ramp] (AU1) is set to 1, the deceleration ramp may be increased or decreased from the setting of dEC, depending on the amount of load on the motor during ramp down. See diagram above. If two different deceleration rates are needed, see parameter [Deceleration time 2] (F501) on page 83.
F500
[Acceleration time 2]
0.0 to 3200 s
20.0 s
Parameter F500 sets the second acceleration time. Switching between acceleration rates 1 and 2 is accomplished by means of: Parameter [Ramp switching] (F504) (see page 85), A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91)
Output Frequency (Hz)
Speed Reference (1) (2) (3) (4) ACC F500 F501 dEC Acceleration Slope Acceleration Slope Deceleration Slope Deceleration Slope
Time (S)
0 (1) (2)
0.0 to 3200 s
(3)
(4)
20.0 s
F501
[Deceleration time 2]
Parameter F501 sets the second deceleration time. Switching between deceleration rates 1 and 2 is accomplished by means of: - Parameter [Ramp switching] (F504) (see page 85), - A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or - A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91). (5) See table page 167.
S1A53838 09/2011
83
Application Parameters
Code
Name / Description
Adjustment range
Factory setting 0
F502
0 1 2
[Acc/dec 1 pattern]
[Linear] [S-ramp 1] (see diagram below) [S-ramp 2] (see diagram below for [Acc/dec 2 pattern] (F503) parameter). The linear acceleration and deceleration pattern is illustrated in diagram on page 83 and is used in most applications. S-pattern 1 (see diagram below) is for use in applications that need the shortest ramp time possible while minimizing jerks during speed changes. See below for more information about parameters [Acc/Dec S-pat start] (F506) and [Acc/Dec S-pat end] (F507).
Output Frequency (Hz) Maximum Frequency Set Frequency
0
x
Time (S)
x
Actual Acceleration Time
F503
0 1 2
[Acc/dec 2 pattern]
[Linear] [S-ramp 1] See diagram below. [S-ramp 2] See previous diagram for parameter Acc/Dec Pattern 1 [Acc/dec 1 pattern] (F502). S-pattern 2 (diagram below) is for use in high-speed spindle applications where acceleration and deceleration rates need to be reduced as the motor operates above its rated operating frequencya constant hp region where motor torque is reduced. Use parameter F503 to select the second Acc/Dec pattern. Switching between Acc/Dec patterns 1 and 2 is accomplished by means of: Parameter [Ramp switching] (F504) (see page 85), A particular operating frequency (see parameter [Commut. ramp freq.] (F505) on page 85), or A logic input assigned to functions 5, 20, 21, 30, 31 35, or 40 (see table beginning on page 91). For more information on Acc/Dec patterns, see parameter [Acc/dec 1 pattern] (F502) above.
Output Frequency (Hz) Maximum Frequency
Constant Region
hp
Time (S)
F506 F507
10%
Use parameter F506 to adjust the lower portion of S-pattern 1. See diagram on page 85. Acc/Dec S-pattern Upper Limit 0 to 50% of acceleration time 10%
Use parameter F507 to adjust the upper portion of the S-pattern 1. See diagram on page 85.
84
S1A53838 09/2011
Application Parameters
Code
Name / Description
Factory setting 1
F504
1 2
[Ramp switching]
Time (S)
F505
0.0 Hz
If parameter F505 is set to a frequency greater than 0.0, the drive will use Acc/Dec pattern 1 above that frequency and Acc/Dec pattern 2 above.
Output Frequency (Hz)
Speed Reference (1) (2) (3) (4) ACC F500 F501 dEC Acceleration Slope Acceleration Slope Deceleration Slope Deceleration Slope
Time (S)
AU1
0 1 2
[Auto ramp]
[Disabled] [Enable] - [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC) (see page 83) [ACC only] - [Acceleration time 1] (ACC) only If parameter AU1 is set to 1 or 2, the drive will monitor its own loading level and optimize the acceleration and deceleration ramps. The acceleration and deceleration (AU1 = 1 only) rates will be automatically adjusted between 1/8 to 8 times the settings of [Acceleration time 1] (ACC) and [Deceleration time 1] (dEC), depending on the drives current rating and the load level on the motor. ACC and dEC should be appropriately set for an average load in the application. If the load on the motor increases rapidly during ramp up or ramp down, the auto ramp adaptation feature may not help prevent the drive from experiencing an overcurrent or overvoltage. If the application requires a consistent acceleration and deceleration time, set AU1 to 0, and set ACC and dEC manually as needed. The manual acceleration and deceleration times can still be overridden by the [Motor Current Limit] (F601) (see page 69) and [Overvoltage fault] (F305) (see page 128) and [Overvoltage level] (F626) (see page 128) functions.
F300
Increasing the switching frequency may reduce audible motor noise. Increasing the switching frequency will increase the heat dissipated by the drive. The capacity of the drive may need to be derated accordingly if the switching frequency is increased. See the derating curves in the ATV212 Installation Manual. (5) See table page 167.
S1A53838 09/2011
85
Application Parameters
Code
Name / Description
Adjustment range
Factory setting 1
F311
0 1 2
[Motor direction]
Use parameter F311 to permit only forward or reverse operation. [Fw & Rev.] [Fw only] [Rev. only]
F312
[Noise reduction]
0 1
Random control of the switching frequency may reduce audible motor noise. Random control of the switching frequency will not be performed if the switching frequency is set above 7.1 kHz, regardless of the setting of F312. [Disable] [Enable]
F316
0 1 2 3
[Fixed] - ATV212pppM3X and ATV212pppN4: switching frequency NOT automatically reduced [Auto] - ATV212pppM3X and ATV212pppN4: switching frequency automatically reduced [460 V fixed] - ATV212pppN4 (2): switching frequency NOT automatically reduced [460 V Auto] - ATV212pppN4 (2): switching frequency automatically reduced If parameter F316 is set to 1 or 3, the switching frequency level will be automatically controlled to help prevent a drive overheating. If the drive senses an impending overheating, it will reduce the switching frequency, thus reducing heat produced by the controller. As the temperature approaches normal, the switching frequency will return to the level selected by parameter [Switch. freq. level] (F300). If F316 is set to 1 or 3, motor control performance is optimized if parameter F300 is set to 6 kHz or 8 kHz. (1) See table page 168. (2) For 400 V applications with motor leads longer than 30 m (100 ft).
86
S1A53838 09/2011
Application Parameters
Skip Frequencies
Do not set the skip frequency bands so that they overlap. While the drive will not operate within these skip frequency bands during steady state operation, skip frequency bands are ignored by the drive during motor acceleration and deceleration.
Code Name / Description Adjustment range Skip frequency 1 midpoint 0.0 to [Max frequency] (FH) Hz Factory setting 0.0 Hz
[Jump frequency 1] [Jump bandwidth 1] [Jump frequency 2] [Jump bandwidth 2] [Jump frequency 3] [Jump bandwidth 3]
0.0 to 30.0 Hz
0.0 Hz
0.0 Hz
0.0 to 30.0 Hz
0.0 Hz
0.0 Hz
0.0 to 30.0 Hz
0.0 Hz
S1A53838 09/2011
87
Application Parameters
0
Output Current (A)
0
DC braking time ON OFF
Run Command
Code
Name / Description
F250
WARNING
NO HOLDING TORQUE z DC injection braking does not provide holding torque at zero speed. z DC injection braking does not work when there is a loss of power or when the drive detects a fault. z When necessary, use a separate brake to maintain torque levels. Failure to follow these instructions can result in death, serious injury, or equipment damage.
When stopping the motor, the drive will apply DC injection braking once the output frequency drops below the level set by parameter F250.
F251
0 to 100%
50% (1)
CAUTION
RISK OF DAMAGE TO THE MOTOR Check that the motor will withstand this current without overheating. Failure to follow this instruction can result in equipment damage. Parameter F251 sets the level of current applied to the motor during DC injection braking. The displayed value, percent or amperes, is set by parameter [Unit value selection] (F701) (see page 120). During DC injection braking, the drives overload protection sensitivity increases. The drive automatically lowers the applied DC current to avoid an overload detected fault.
F252
0.0 to 20.0 s
1.0 s
CAUTION
RISK OF DAMAGE TO THE MOTOR z Long periods of DC injection braking can cause overheating and damage the motor. z Protect the motor by avoiding long periods of DC injection braking. Failure to follow this instruction can result in equipment damage. Parameter F252 determines how long DC injection braking is applied to the motor. (1) Percentage of the drive's rated current or ampere range. This will vary according to drive power rating.
88
S1A53838 09/2011
8
What's in this Chapter? This chapter contains the following topics:
Topic Logic Inputs Functions Logic Input Function Compatibility Relay Output Functions Analog Input Functions Analog Output Functions Analog Input Adjustments Active Logic Function Preset Speeds +/- Speed Control Parameters Damper control Page 90 97 98 104 105 106 112 112 113 116
S1A53838 09/2011
89
The setting of parameter F111 determines the control function of logic input terminal F. R Logic Input Function 0 to 73 6
The setting of parameter F112 determines the control function of logic input terminal R. RES Logic Input Function 0 to 73 10
The setting of parameter F113 determines the control function of logic input terminal RES. VIA Input Function (Analog or Logic Selection) 0
DANGER
UNINTENDED EQUIPMENT OPERATION Prevent accidental grounding of logic inputs configured for sink logic. Accidental grounding can result in unintended activation of drive functions. Protect the signal conductors against damage that could result in unintentional conductor grounding. Failure to follow these instructions will result in death or serious injury.
0 1 2 [AI]: Analog input [LI sink]: Logic input - sink (negative logic) [LI source]: Logic input - source (positive logic) The setting of parameter F109 determines whether control input terminal VIA will serve as an analog input (0-10 Vdc or 0 20 mA) or as a logic input (either sink or source). When configuring VIA as a logic input, be certain to slide switch SW100 on the main control board to the V (voltage) position. When configuring VIA as a logic input using sink (negative) logic, be certain to connect a 4.7 k (1/2 W) resistor between control terminals P24 and VIA. For more information on the use of control input terminal VIA, see ATV212 Installation manual.
F118
[VIA LI selection]
0 to 73
Set first parameter [VIA selection] (F109) before setting parameter F118. The setting of parameter F118 determines the control function of logic input terminal VIA. See page 91 for a complete list of VIA logic input assignments.
90
S1A53838 09/2011
Logic inputs F, R, RES, and VIA (if parameter [VIA selection] (F109) is set to 1 or 2) can be set to the functions described in the table below. See table on page 97 for logic input function compatibility.
Function No. 0 1 Description [No assigned] No function assigned [Run permissive] (see also input function 54, page 95) [Forward] (2-wire control: input function 49 NOT used) or (3-wire control: input function 49 USED) Logic input disabled OFF: drive motor output disabled, motor coasts to stop ON: drive ready for operation If [Logic Funct 2 active] (F110) is not set to 1 [Run permissive], a logic input should be assigned to the [Run permissive] logic function to enable the motor to start. Mode 2-wire control Mode 3-wire control 3-wire control 3 [Reverse] (2-wire control: input function 49 NOT used) or (3-wire control: input function 49 USED) Mode 2-wire control Mode 3-wire control 3-wire control 5 6 [Acc / Dec] [PS1] Preset speed command input 1 Logic Input Action OFF: Motor ramps down to a stop ON: Motor runs forward Stop Input State OFF ON Logic Input Action OFF: no function ON: no function OFF to ON transition starts the drive, motor runs forward Action
Logic Input Action OFF: Motor ramps down to a stop ON: Motor runs reverse Stop Input State OFF ON Logic Input Action OFF: no function ON: no function OFF to ON transition starts the drive, motor runs in reverse
OFF: Acceleration/deceleration pattern 1 ON: Acceleration/deceleration pattern 2 Input 3 0 Input 2 0 Input 1 0 Motor Speed minimum speed or speed reference per [Frequency mode sel] (FMOd) Sr1: preset speed 1 Sr2: preset speed 2 Sr3: preset speed 3 Sr4: preset speed 4 Sr5: preset speed 5 Sr6: preset speed 6 Sr7: preset speed 7
0 7 [PS2] Preset speed command input 2 [PS3] Preset speed command input 3 [Fault reset] (see also input function 55, page 95) 0 0 1 8 1 1 1 10
0 1 1 0 0 1 1
1 0 1 0 1 0 1
DANGER
UNINTENDED EQUIPMENT OPERATION This configuration enables to reset the drive. Check this action will not endanger personnel or equipment in any way Failure to follow these instructions will result in death or serious injury. ON to OFF transition clears a detected fault (if cause of detected fault has been cleared)
11
OFF: No external detected fault ON: Motor stops according to method set by parameter [Ext. fault stop Mode] (F603) Embedded display terminal displays E detected fault, detected fault relay activated
S1A53838 09/2011
91
Action
WARNING
NO HOLDING TORQUE z DC injection braking does not provide any holding torque at zero speed. z DC injection braking does not work when there is a loss of power or when the drive detects a fault. z Where necessary, use a separate brake to maintain torque levels. Failure to follow these instructions can result in death, serious injury, or equipment damage. OFF: No DC braking command ON: DC braking applied to motor, Level and time set by parameters [DC braking current] (F251) and [DC braking time] (F252) 14 [PID disable] OFF: PID control permitted ON: PID control prohibited PID control prohibited input terminal function is available to switch PID control and openloop control. Also Clear PID integral value input terminal function (function 65) is available. Note: For software version lower than V1.7IE04, when Clear PID integral value (function 65) and PID Control Prohibited (function 14) are used, it is necessary to set [Command mode sel] (CMOd) to [Logic inputs] (O) Control terminal logic inputs. OFF: Parameters locked (if parameter F700 = 1) ON: Programming changes permitted
15
[Param Edit] Functional only when parameter [Parameter lock] (F700) = 1 [Run reset]
16
OFF: drive motor output disabled, motor coasts to stop ON: drive ready for operation ON to OFF transition clears a detected fault (if cause of detected fault has cleared) OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs forward, ramping up per ACC/dEC pattern 2
20
[FW-RMP2] Combination of forward run command and acceleration/deceleration pattern 2 selection [Rev- RMP2] Combination of reverse run command and acceleration/deceleration pattern 2 selection [FW, PS1] Combination of forward run command and preset speed 1 command [RV, PS1] Combination of reverse run command and preset speed 1 command [FW, PS2] Combination of forward run command and preset speed 2 command [RV, PS2] Combination of reverse run command and preset speed 2 command [FW, PS3] Combination of forward run command and preset speed 3 command
21
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs in reverse, ramping up per ACC/dEC pattern 2
22
OFF: Motor ramps down to a stop ON: Motor runs forward, at speed set by Sr1, preset speed 1
23
OFF: Motor ramps down to a stop ON: Motor runs in reverse, at speed set by Sr1, preset speed 1
24
OFF: Motor ramps down to a stop ON: Motor runs forward, at speed set by Sr2, preset speed 2
25
OFF: Motor ramps down to a stop ON: Motor runs in reverse, at speed set by Sr2, preset speed 2
26
OFF: Motor ramps down to a stop ON: Motor runs forward, at speed set by Sr3, preset speed 3
92
S1A53838 09/2011
Function No. 27 Description [RV, PS3] Combination of reverse run command and preset speed 3 command [FW-RMP2-SP1] Combination of forward run command, preset speed 1 command, and acceleration/deceleration pattern 2 selection [Rev-RMP2-SP1] Combination of reverse run command, preset speed 1 command, and acceleration/deceleration pattern 2 selection [FW-RMP2-SP2] Combination of forward run command, preset speed 2 command, and acceleration/deceleration pattern 2 selection [Rev-RMP2-SP2] Combination of reverse run command, preset speed 2 command, and acceleration/deceleration pattern 2 selection [FW-RMP2-SP3] Combination of forward run command, preset speed 3 command, and acceleration/deceleration pattern 2 selection [Rev-RMP2-SP3] Combination of reverse run command, preset speed 3 command, and acceleration/deceleration pattern 2 selection [Frequency source] Frequency reference source switching [Motor switch]
Action
OFF: Motor ramps down to a stop ON: Motor runs in reverse, at speed set by Sr3, preset speed 3
30
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs forward, at speed set by Sr1, preset speed 1, ramping up per ACC/dEC pattern 2
31
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs in reverse, at speed set by Sr1, preset speed 1, ramping up per ACC/dEC pattern 2
32
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs forward, at speed set by Sr2, preset speed 2, ramping up per ACC/dEC pattern 2
33
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs in reverse, at speed set by Sr2, preset speed 2, ramping up per ACC/dEC pattern 2
34
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs forward, at speed set by Sr3, preset speed 3, ramping up per ACC/dEC pattern 2
35
OFF: Motor stops, ramping down per ACC/dEC pattern 2 ON: Motor runs in reverse, at speed set by Sr3, preset speed 3, ramping up per ACC/dEC pattern 2
38
OFF: drive follows speed reference set by parameter [Frequency mode sel] (FMOd) ON: drive follows speed reference set by parameter [Remote spd ref 2] (F207) > (if [Auto/man speed ref] (F200) = 1)
39
CAUTION
RISK OF DAMAGE TO THE MOTOR z The motor switching function disables motor thermal protection. z The use of external overload protection is required when using motor switching. Failure to follow these instructions can result in death, serious injury, or equipment damage. OFF: 1st motor V/Hz parameter set active: ([Mot cont. mode sel.] (Pt), [Motor rated freq.] (uL), [Motor rated voltage] (uLu), [Mot Voltage Boost] (ub), [Motor thermal prot.] (tHr)) ON: 2nd motor V/Hz parameter set active: (Pt = 0, F170, F171, F172, F173)
S1A53838 09/2011
93
Function No. 40 Description [Mot param. switch] Motor control parameter switching V/Hz, current limit, acceleration/deceleration pattern
Action
CAUTION
RISK OF DAMAGE TO THE MOTOR z The parameter switching function disables motor thermal protection. z The use of external overload protection is required when using motor switching. Failure to follow these instructions can result in death, serious injury, or equipment damage. OFF: 1st motor control parameter set active: ([Mot cont. mode sel.] (Pt), [Motor rated freq.] (uL), [Motor rated voltage] (uLu), [Mot Voltage Boost] (ub), [Motor thermal prot.] (tHr), [Acceleration time 1] (ACC), [Deceleration time 1] (dEC), [Acc/dec 1 pattern] (F502), [Motor Current Limit] (F601)) ON: 2nd motor control parameter set active: (Pt = 0, F170, F171, F172, F173, F185, F500, F501, F503)
41 42 43 44 45
[(+) speed] [(-) speed] [+/- clear] [+/- SPD, FLT CLR] [Inv Ext. fault] Inversion of external detected fault signal (see also input function 11, page 91) [Ext. Th fault] External overheating input (see also input function 47) [Inv Ext. Th fault] Inversion of external overheating input (see also input function 46) [Forced local]
OFF: No motor speed increase ON: Motor accelerates OFF: No motor speed reduction ON: Motor decelerates OFF to ON transition clears frequency level set by +/- speed inputs OFF to ON transition clears frequency level set by +/- speed inputs ON to OFF transition clears a detected fault (if cause of detected fault has been cleared) OFF: Motor stops according to method set by parameter [Ext. fault stop Mode] (F603) Embedded display terminal displays E detected fault ON: No external detected fault
46
OFF: No external overheating ON: Motor stops, embedded display terminal displays OH2
47
OFF: Motor stops, embedded display terminal displays OH2 ON: No external overheating
48
OFF: No forced local function ON: Control of the drive is forced to mode set by [Frequency mode sel] (FMOd), [Command mode sel] (CMOd), and [Remote spd ref 2] (F207). OFF: Motor ramps down to a stop ON: drive ready for operation OFF: No function ON: Clears kWh memory
49 51
[3-wire] [Reset kWh] Clear accumulated power consumption kWh display [Forced mode]
52
DANGER
LOSS OF PERSONNEL AND EQUIPMENT PROTECTION When F650 is set to 1 or 2 and a logic input set to function "52" is activated, all the drive controller protection will be disable. Logic input should not be enable on function 52 for typical applications... Logic input should be enable on function 52 only in extraordinary situations where a thorough risk analysis demonstrates that the presence of adjustable speed drive protection poses a greater risk than personnel injury or equipment damage. Failure to follow these instructions will result in death or serious injury. This function enables the "Forced fire" mode. In this mode, all the detected fault will be ignored or if it is a hardware trip, the drive will be reset to try to restart. OFF: No function ON: Motor runs at speed set by F294 Note: F650, F659 and F294 must be configured to activate this function.
94
S1A53838 09/2011
Action
This function enables the "Fire" mode OFF: No function ON: Motor runs at speed set by F294 Note: F650, F659 and F294 must be configured to activate this function. OFF: drive ready for operation ON: drive motor output disabled, motor coasts to stop This mode allows to have a freewheel stop using a terminal command.
54
[Inverse Run permis.] Inversion of run permissive (see also input function 1 page 91) [Inv fault reset] Inversion of clear detected fault (see also input function 10 page 91)
55
DANGER
UNINTENDED EQUIPMENT OPERATION This configuration enables to reset the drive. Check this action will not endanger personnel or equipment in any way Failure to follow these instructions will result in death or serious injury. OFF to ON transition clears a detected fault (if cause of detected fault has been cleared)
56
[Run, FW] Combination of run permissive and run forward command (2-wire control only) [Run, RV] Combination of run permissive and run reverse command (2-wire control only) [I limit 1/2] Current limit level selection [RY on] Holding of RYA-RYC relay output [Cancel HMI cmd] Cancellation of last graphic display option command [PID integral] Clear PID integral value [Run-fw-sp1] Combination of run permissive, run forward command, and preset speed 1 command [Run-rev-sp1] Combination of run permissive, run reverse command, and preset speed 1 command [Run-fw-sp2] Combination of run permissive, run forward command, and preset speed 2 command [Run-rev-sp2] Combination of run permissive, run reverse command, and preset speed 2 command
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs forward
57
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs reverse
61
OFF: Current limit level 1 [Motor Current Limit] (F601) selected ON: Current limit level 2 [Mot. 2 current limit] (F185) selected OFF: Normal real-time relay operation ON: RYA-RYC is held on once activated OFF: Last graphic display option command cancelled ON: Last graphic display option command retained
62
64
65 66
OFF: No action ON: PID integral value held at zero OFF: drive motor output disabled, motor coasts to stop ON: Motor runs forward at speed set by Sr1, preset speed 1
67
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs reverse at speed set by Sr1, preset speed 1
68
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs forward at speed set by Sr2, preset speed 2
69
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs reverse at speed set by Sr2, preset speed 2
S1A53838 09/2011
95
Function No. 70 Description [Run-fw-sp4] Combination of run permissive, run forward command, and preset speed 4 command [Run-rev-sp4] Combination of run permissive, run reverse command, and preset speed 4 command [PID rev] PID error signal reversed [Damper feedBack]
Action
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs forward at speed set by Sr4, preset speed 4
71
OFF: drive motor output disabled, motor coasts to stop ON: Motor runs reverse at speed set by Sr4, preset speed 4
72 73
OFF: if F111 = 72 and F terminal is OFF, PI error input = reference - feedback ON: if F111 = 72 and F terminal is ON, PI error input = feedback - reference OFF: if F111 or F112 or F113 is not set to 73 the damper has no effect. ON: if F111 or F112 or F113 = 73 the damper is ON. The damper feedback has not effect if not configured to an output.
96
S1A53838 09/2011
Function No. / Function 1/54 2 3 5 6~8 [No assigned] / [Inverse Run permissive] [Forward] [Reverse] [Acc / Dec] [PS1]~[PS3]
1/54
2 @
3 @ X
5 @ O O
6-9 @ O O O
10/55 11/45 O O O O O O X X X X X @ O O O @ O O O O O O @ X X O + O O X O O O @
13 @ X X X X O @
14 O O O O O O @ @
15 O O O O O O O O O
46/47 O X X X X X + X X O
48 O O O O O O O O O O O
41-43 O O O O O O @ @ O O O O
49 @ X X O O O @ @ O O @ O O
38 O O O O O O O O O O O O O O
39 O O O O O O O O O O O O O O O
40 O O O X O O O O O O O O O O O X
52/53 X X X O X X X X X O X X X X X O O
+ + + + O + + O O @ O O + O O O @ + O O O @ @ O O @ O O @ O O O @
O O O @ @ O O @ O O @ O O O @ O O @ @ O O @ O O O O O @ O
10/55 [Fault reset] / [Inv fault reset] 11/45 13 14 15 46/47 48 41-43 49 38 39 40 52/53 [Ext. fault] / [Inv. Ext. fault] [DC braking] [PID disable] [Param Edit] [Ext. Th fault] / [Inv Ext. Th fault] [Forced local] [(+) speed] [(-) speed] [+/- clear] [3-wire] [Frequency source] [Motor switch] [Mot param. switch] [Forced mode] / [Fire mode]
O @ @ O O @ O O O O O O @
X O @ O O X O O O @ O @ O O O O O O @
O O O O O O O O O O X O O O @
O O O O O @ O O O O @
O O O @ O O @
@ O O
The following logic input functions are active, regardless of the [Frequency mode sel] (FMOd) and [Command mode sel] (CMOd) setting.
z z z
(1) Run permissive (10) Clear detected fault (11) External detected fault
When determining function compatibility using the table above, the function listed horizontally is activated first and the function listed vertically is activated second.
S1A53838 09/2011
97
Function No. / Description 0 1 2 3 4 [Low speed reach] Low speed reached [Inv low spd reach] Inversion of low speed reached [High speed reach] High speed reached [Inv Hi spd reach] Inversion of high speed reached [F100 speed reach] F100 speed reached (See page 114 for more details on parameter F100) [Inv F100 sp reach] Inversion of F100 speed reached [Speed reach] Commended speed reached [Inv speed reach]
Action OFF: output frequency is low speed setting [Low limit frequency] (LL) ON: output frequency is > low speed setting LL OFF: output frequency is > low speed setting [Low limit frequency] (LL) ON: output frequency is low speed setting LL
OFF: output frequency is < high speed setting [Upper limit freq] (UL) ON: output frequency is high speed setting UL OFF: output frequency is high speed setting [Upper limit freq] (UL) ON: output frequency is < high speed setting UL
OFF: output frequency is < [Freq. 1 reached] (F100) speed setting ON: output frequency is F100 speed setting
5 6
OFF: output frequency is [Freq. 1 reached] (F100) speed setting ON: output frequency is < F100 speed setting OFF: output frequency is commanded speed +/- [Freq.2 bandw.] (F102) hysteresis band ON: output frequency is > commanded speed +/- F102 hysteresis band OFF: output frequency is > commanded speed +/- [Freq.2 bandw.] (F102) hysteresis band ON: output frequency is commanded speed +/- F102 hysteresis band OFF: output frequency is [Freq. 2 reached] (F101) speed +/- [Freq.2 bandw.] (F102) hysteresis band ON: output frequency is > F101 speed +/- F102 hysteresis band OFF: output frequency is > [Freq. 2 reached] (F101) speed +/- [Freq.2 bandw.] (F102) hysteresis band ON: output frequency is F101 speed +/- F102 hysteresis band OFF: No drive detected fault ON: drive detected fault
10
WARNING
LOSS OF CONTROL z When F130, F132, F137 is set to 10, the output will be active when the drive will detect a fault. z The drive status will not be detected if the wiring is damaged for any reason. z Do not select10 unless you are sure that your signal will be present in any case. Failure to follow these instructions can result in death, serious injury, or equipment damage.
11
[No drive fault] Inversion of Drive fault function. [Overload flt] Overtorque fault Overtorque fault detection is active only if parameter F615 = 1. See page 132 for more detail on an overtorque detected fault and parameters F616 and F618.) [Inv overload flt] Inversion of Overload flt function
OFF: drive detected fault ON: No drive detected fault OFF: Estimated motor torque has NOT been at [Overtorque level] (F616) level for a time period longer than that set by [Ovtorque det time] (F618) ON: Estimated motor torque has been at F616 level for a time period longer than that set by F618. drive stopped, displaying Ot
12
13
OFF: Estimated motor torque has been at [Overtorque level] (F616) level for a time period longer than that set by [Ovtorque det time] (F618). drive stopped, displaying Ot ON: Estimated motor torque has NOT been at F616 level for a time period longer than that set by F618
98
S1A53838 09/2011
Function No. / Description 14 [Drive running] Run relay [Drive no run] Inversion of Drive no run function [Motor overload] Motor overload alarm detection is only active if parameter OLM is set to either 0, 1, 4, or 5. See page 135 for more detail on motor overload protection settings. [Inv mot. overload] Inversion of Motor overload function [Torque alarm] Overtorque alarm detection is active only if parameter F615 = 0. See page 132 for more detail on the overtorque alarm and parameters [Overtorque level] (F616), [Overtorque band] (F619). [Inv torque alarm] Inversion of Torque alarm function [Gen. alarm] General alarm
Action OFF: drive is not powering the motor ON: drive is powering the motor, accelerating, decelerating, at constant speed, or DC braking OFF: drive is powering the motor, accelerating, decelerating, at constant speed, or DC braking ON: drive is not powering the motor OFF: motor thermal state is < 50% of motor overload detected fault level ON: motor thermal state is 50% of motor overload detected fault level
15
16
17 20
OFF: motor thermal state is 50% of motor overload detected fault level ON: motor thermal state is < 50% of motor overload detected fault level OFF: Estimated motor torque is < 70% of F616 level minus F619 hysteresis band ON: Estimated motor torque is 70% of F616 level
21
OFF: Estimated motor torque is 70% of [Overtorque level] (F616) level ON: Estimated motor torque is < 70% of F616 level minus [Overtorque band] (F619) hysteresis band OFF: No detected fault condition from the sources listed below exists ON: A detected fault has been issued by one of the following sources:
22
Overtorque detected fault (output functions 12 and 13) Motor overload (output functions 16 and 17) Overtorque detected fault (output functions 20 and 21) Load detection loss (output functions 24 and 25) Run time (output functions 42 and 43) Undervoltage (output functions 54 and 55) drive in sleep mode (see for more detail on parameter F256) Power loss (see for more detail on parameter F302) Overcurrent motor current limit level (parameter F601) Overvoltage DC bus voltage overvoltage stall level (parameter F626) Drive overheating
23 [Inv gen. alarm] Inversion of General alarm function OFF: A detected fault has been issued by one of the following sources:
Overtorque detected fault (output functions 12 and 13) Motor overload (output functions 16 and 17) Overtorque detection loss (output functions 20 and 21) Failure of load detection (output functions 24 and 25) Run time (output functions 42 and 43) Undervoltage (output functions 54 and 55) Drive in sleep mode (see for more detail on parameter F256) Power loss (see for more detail on parameter F302) Overcurrent motor current limit level (parameter F601) Overvoltage DC bus voltage overvoltage stall level (parameter F626) drive overheating
ON: No alarm condition from the sources listed above exists OFF: Motor current is greater than F611 level + F609 hysteresis band ON: Motor current is less than F611 level for the time set by F612
24
[Underload detect.] (See page 130 for more detail on parameters F609 F612 and the underload function.) [Inv underl. det.] Inversion of Underload detect. function
25
OFF: Motor current is less than F611 level for the time set by F612 ON: Motor current is greater than F611 level + F609 hysteresis band
S1A53838 09/2011
99
Action OFF: None of the detected fault conditions listed below exist ON: One (or more) of the following detected fault conditions exists and has stopped the drive:
27
E external detected fault E-18 VIA analog input signal detected fault E-19 main control board CPU communication E-20 excessive torque boost E-21 main control board CPU detected fault 2 EEP1 main control board EEPROM detected fault 1 EEP2 main control board EEPROM detected fault 2 EEP3 main control board EEPROM detected fault 3 EF2 ground detected fault EPH0 output phase detected fault detection EPH1 input phase detected fault detection Err1 speed reference Err2 main control board RAM Err3 main control board ROM Err4 main control board CPU detected fault 1 Err5 serial communication control Err7 motor current sensor Err8 serial communication network Err9 graphic display option communication interruption Etn1 auto-tuning EtYP drive ratings OCA short-circuit detected in drive output inverter stage during motor startup OCL short-circuit detected in motor or output wiring during motor startup OH2 - external overheating Ot overtorque Uc underload UP1 - Undervoltage
OFF: One (or more) of the following fault conditions exists and has stopped the drive:
E external detected fault E-18 VIA analog input signal E-19 main control board CPU communication E-20 excessive torque boost E-21 main control board CPU detected fault 2 EEP1 main control board EEPROM detected fault 1 EEP2 main control board EEPROM detected fault 2 EEP3 main control board EEPROM detected fault 3 EF2 ground fault EPH0 output phase loss detection EPH1 input phase loss detection Err1 speed reference Err2 main control board RAM Err3 main control board ROM Err4 main control board CPU detected fault 1 Err5 serial communication control Err7 motor current sensor Err8 serial communication network Err9 graphic display option communication interruption Etn1 auto-tuning EtYP drive ratings OCA short-circuit detected in drive output inverter stage during motor startup OCL short-circuit detected in motor or output wiring during motor startup OH2 - external overheating Ot overtorque Uc underload UP1 - Undervoltage
100
S1A53838 09/2011
Action OFF: None of the detected fault conditions listed below exist ON: One (or more) of the following detected fault conditions exists:
[Auto-reset fault] Auto-clear detected fault Note: Relay activates when maximum number of autoclear set by [Number auto reset] (F303) page 124 is reached.
Fd1 damper detected fault 1 (closed damper) Fd2 damper detected fault 2 (opened damper) OC1 overcurrent during acceleration OC2 overcurrent during deceleration OC3 overcurrent during constant speed OC1P Short circuit or ground detected fault during acceleration OC2P Short circuit or ground detected fault during deceleration OC3P Short circuit or ground detected fault during constant speed OH drive overheating OL1 drive overload OL2 motor overload OP1 overvoltage during acceleration OP2 overvoltage during deceleration OP3 overvoltage during constant speed Fd1 damper detected fault 1 (closed damper) Fd2 damper detected fault 2 (opened damper) OC1 overcurrent during acceleration OC2 overcurrent during deceleration OC3 overcurrent during constant speed OC1P Short circuit or ground detected fault during acceleration OC2P Short circuit or ground detected fault during deceleration OC3P Short circuit or ground detected fault during constant speed OH drive overheating OL1 drive overload OL2 motor overload OP1 overvoltage during acceleration OP2 overvoltage during deceleration OP3 overvoltage during constant speed
29
OFF: One (or more) of the following detected fault conditions exists:
Note: Relay deactivates when maximum number of autoclear set by [Number auto reset] (F303) page 124 is reached.
ON: None of the detected fault conditions listed above exist 30 [Drive rdy 1] drive ready condition 1 [Inv drive rdy 1] Inversion of Drive rdy 1 function [Drive rdy 2] drive ready condition 2 [Inv drive rdy 2] Inversion of Drive rdy 2 function [VIB ref source] VIB input reference source [Inv VIB ref source] Inversion of VIB ref source function OFF: drive not ready for operation ON: drive ready for operation (ready includes active run permissive and active run command) OFF: drive ready for operation (ready includes active run permissive and active run command) ON: drive not ready for operation OFF: drive not ready for operation ON: drive ready for operation (ready does not include active run permissive or active run command) OFF: drive ready for operation (ready does not include active run permissive or active run command) ON: drive not ready for operation OFF: analog input terminal VIB is NOT the active speed reference source ON: VIB is the active speed reference source OFF: analog input terminal VIB is the active speed reference source ON: VIB is NOT the active speed reference source
31
32
33
34 35
S1A53838 09/2011
101
Function No. / Description 36 [Fault relay] (The drive is not in a fault state during auto clear detected fault attempts. See also function 10 page 98)
Action
WARNING
LOSS OF CONTROL z When F130, F132, F137 is set to 36, the output will be active when the drive will detect a fault. z The drive status will not be detected if the wiring is damaged for any reason. z Do not select 36 unless you are sure that your signal will be present in any case. Failure to follow these instructions can result in death, serious injury, or equipment damage. OFF: No drive detected fault ON: drive detected fault. Relay activates when a clearable fault occurs and the drive attempts to restart. Relay deactivates when drive is restarting.
37
OFF: drive detected fault ON: No drive detected fault Relay deactivates when a clearable fault occurs and the drive attempts to restart. Relay activates when drive is restarting. OFF: Serial communication word FA50 bit 0 = 0 ON: Serial communication word FA50 bit 0 = 1 OFF: Serial communication word FA50 bit 0 = 1 ON: Serial communication word FA50 bit 0 = 0 OFF: Serial communication word FA50 bit 1 = 0 ON: Serial communication word FA50 bit 1 = 1 OFF: Serial communication word FA50 bit 1 = 1 ON: Serial communication word FA50 bit 1 = 0 OFF: Run time is < F621 time setting ON: Run time is F621 time setting
38 39 40 41 42
[Ser. data relay FL] Serial communication data [Inv ser. dat rel. FL] Inversion of ser. dat rel. FL function [Ser. data relay RY] Serial communication data [Inv ser. dat rel RY] Inversion of ser. dat rel. RY function [Drive run time al] Drive operational run time alarm (see page 120 for more detail on parameter F621). [Inv.drive run time al] Inversion of Drive run time al function [Drive serv. alarm] Drive service alarm (see page 133 for more detail on parameter F634). [Inv. drive serv. alarm] Inversion of Drive serv. alarm function [LI F state] Logic input F state [Inv. LI F state] Inversion of LI F state function [LI R state] Logic input R state [Inv. LI R state] Inversion of LI R state function [Speed ref = VIA] Drive speed reference equals VIA signal
43 44
OFF: Run time is F621 time setting ON: Run time is < F621 time setting OFF: drive maintenance detected fault not active ON: drive maintenance detected fault active
45 48 49 50 51 52
OFF: drive maintenance detected fault active ON: drive maintenance detected fault not active OFF: Logic input F is not active ON: Logic input F is active OFF: Logic input F is active ON: Logic input F is not active OFF: Logic input R is not active ON: Logic input R is active OFF: Logic input R is active ON: Logic input R is not active OFF: Speed reference from the source identified by [Frequency mode sel] (FMOd) or the source identified by [Remote spd ref 2] (F207) VIA signal ON: Speed reference from the source identified by FMOd or the source identified by F207 = VIA signal OFF: Speed reference from the source identified by [Frequency mode sel] (FMOd) or the source identified by [Remote spd ref 2] (F207) = VIA signal ON: Speed reference from the source identified by FMOd or the source identified by F207 VIA signal
53
102
S1A53838 09/2011
Function No. / Description 54 55 56 57 58 [Undervolt. alarm] Undervoltage alarm [Inv. undervolt. alarm] Inversion of Undervolt. al. function [Loc / remote] Local/remote switching [Inv. loc / remote] Inversion of Loc / remote function [PTC alarm] PTC thermal alarm
Action OFF: Undervoltage detected fault is not active ON: Undervoltage detected fault is active OFF: Undervoltage detected fault is active ON: Undervoltage detected fault is not active OFF: drive is in remote mode ON: drive is in local mode OFF: drive is in local mode ON: drive is in remote mode OFF: Motor temperature as indicated by PTC thermal probes is < 60% of the detected fault level ON: Motor temperature as indicated by PTC thermal probes is 60% of the detected fault level OFF: Motor temperature as indicated by PTC thermal probes is 60% of the detected fault level ON: Motor temperature as indicated by PTC thermal probes is < 60% of the detected fault level OFF: Speed reference from the source identified by [Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2] (F207) VIB signal ON: Speed reference from source identified by FMOd or the source identified F207 = VIB signal OFF: Speed reference from source identified by [Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2] (F207) = VIB signal ON: Speed reference from the source identified by FMOd or the source identified F207 VIB signal ON: The value of VIA is equal to or higher than F160 + F161 OFF: The value of VIA is equal to or lower than F160 - F161 ON: The value of VIA is equal to or lower than F160 - F161 OFF: The value of VIA is equal to or higher than F160 + F161 ON: The value of VIB is equal to or higher than F162 + F163 OFF: The value of VIB is equal to or lower than F162 - F163 ON: The value of VIB is equal to or lower than F162 - F163 OFF: The value of VIB is equal to or higher than F162 + F163 ON: The ouptput frequency is equal to or higher than F101 + F102 OFF: The ouptput frequency is equal to or lower than F101 - F102 (See page 114 for more detail on parameters F101 and F102.) ON: The ouptput frequency is equal to or lower than F101 - F102 OFF: The ouptput frequency is equal to or higher than F101 + F102 (See page 114 for more detail on parameters F101 and F102.) ON: The damper is ON. OFF: The damper is OFF (see page 116) ON: The damper is OFF. OFF: The damper is ON (see page 116) OFF ON
59
60
61
62
[VIA detection] Analog VIA detection [Inv. VIA detection] Inversion of VIA detection function [VIB detection] Analog VIB detection [Inv. VIB detection] Inversion of VIB detection function [Freq. reach hyst] Set frequency attainment signal with hysteresis [Inv. freq. reach hyst] Inversion of Freq. reach hyst function [Damper] Damper control [Inv. damper] Inversion of Damper function [Relay OFF] Relay output is OFF [Relay ON] Relay output is ON
63 64 65 66
67
68 69 254 255
S1A53838 09/2011
103
z z
z z
z z
VIA can accept the following signal types: - Voltage (V): 010 V, voltage or potentiometer input - Current (I): 020 mA or 420 mA The signal type (V or I) is selected by setting SW100 on the main control board. For information on wiring, consult the ATV212 Installation manual. The slope and bias of the input signal are adjusted with parameters F201F204 and F470F471. For more information, see page 106. VIA is configured as the speed reference input in the following macro-configurations: - Run permissive - 3-wire - 4-20 mA. Relay output functions 34 and 35 can signal when VIA is being used as the speed reference source. For more information, see table on page 101 and consult I/O Control Parameters on page 90. Relay output functions 52 and 53 can be used to signal the results of a comparison between the signal at VIA and the speed reference commanded by [Frequency mode sel] (FMOd) or [Remote spd ref 2] (F207). This function can also be used to send out a signal indicating whether the amount of processing and the amount of feedback agree with each other. For more information, see table on page 98. Also, consult I/O Control Parameters on page 90 and review information about parameter F167 on page 115. The drive can enter a detected fault state if the VIA signal drops below a specified level for more than 300 mS. For more information, see parameter F633 on page 130 and code E-18 on page 150. VIA can serve as an analog or a logic input, depending on setting of parameter F109 (set to 0 for analog input). Analog input is the factory setting. See page 90 for more information about parameter F109.
VIB can accept the following signal types: Voltage (V): 010V, voltage or potentiometer input PTC motor thermal sensor input. For more information, see parameters F645 and F646 on page 111. Adjust the slope and bias of the input signal with parameters F210 - F213 and F472 - F473. For more information, see page 106. Relay output functions 52 and 53 can signal when VIA is being used as the speed reference source. For more information, see table on page 102 and consult I/O Control Parameters on page 90. Relay output functions 60 and 61 can be used to signal the results of a comparison between the signal at VIB and the speed reference commanded by [Frequency mode sel] (FMOd) or [Remote spd ref 2] (F207). This function can also be used to send out a signal indicating whether the amount of processing and the amount of feedback agree with each other. For more information, see table on page 98. Also, consult I/O Control Parameters on page 90 and review information about parameter F167 on page 115.
General
z
z z z
The selection of VIA or VIB as the speed reference input in remote mode is made through parameters [Frequency mode sel] (FMOd) and [Remote spd ref 2] (F207). FMOd is the primary speed reference source, while F207 is the secondary source. Switching between the two is determined by the setting of parameter [Auto/man speed ref] F200. For more information, see page 108. Analog output terminal FM can be configured to provide a signal in proportion to the VIA or VIB signal levels. See parameter FMSL, selections 13 and 14, on page 108. When PID control is enabled, VIA or VIB can serve as the setpoint input. Either VIA or VIB needs to be selected as the feedback input. See page 110 for more information on parameter F360 and PID control. Information can be transferred between the serial communication network and the analog inputs via read and write functions F870, F871, and F875-F879. For more information, see pages 140 to 141.
104
S1A53838 09/2011
When switch SW101 is set to V (voltage), FM outputs a 010 Vdc signal at 1 mA. When switch SW101 is set to I (current), FM outputs a 020 mA signal up to 24 Vdc. For detail on proper wiring, consult the ATV212 Installation manual.
The drive value represented by the FM analog output signal is determined by the setting of parameter [AO funct. selection] (FMSL) (see page 108). Calibrating the FM signal output to provide full scale deflection on an analog meter is achieved by adjusting parameter [AO scaling] (FM) (see page 108). The slope and bias of the FM analog output signal can be adjusted using parameters F691 and F692. For more information, see page 109.
S1A53838 09/2011
105
A further refinement of the bias and slope of the analog input signals can be made with parameters F470 F473.
Code Name / Description Adjustment range VIA speed reference level 1 0 to 100% Factory setting 0%
F201 F202 F203 F204 F160 F161 F210 F211 F212 F213 F162 F163
[VIA ref point 1] [VIA freq. point 1] [VIA ref point 2] [VIA freq. point 2] [VIA rel thresh. logic] [VIA threshold hyst.] [VIB ref. point 1] [VIB freq. point 1] [VIB ref. point 2] [VIB freq. point 2] [VIB rel thresh. logic] [VIB threshold hyst.]
0.0 to 200.0 Hz
0.0 Hz
0 to 100%
100%
0.0 to 200.0 Hz
50.0 Hz
0 to 100%
0%
0 to 20%
3%
0 to 100%
0%
0.0 to 200.0 Hz
0.0 Hz
0 to 100%
100%
0.0 to 200.0 Hz
50.0 Hz
0 to 100%
0%
0 to 20%
3%
106
S1A53838 09/2011
Code
Name / Description
F470
[VIA bias]
DANGER
UNINTENDED EQUIPMENT OPERATION If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB. Failure to follow these instructions will result in death or serious injury.
F471 F472
0 to 255
148
0 to 255
128
DANGER
UNINTENDED EQUIPMENT OPERATION If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB. Failure to follow these instructions will result in death or serious injury.
F473
[VIB gain]
0 to 255
148
Hz
Smaller
Maximum frequency
Large
Default Setting
,
Smaller
Parameters [VIA bias] (F470) and [VIB bias] (F472) are factory set so that a minimal signal needs to be applied to VIA or VIB before the drive starts the motor.
z z
To increase the signal level required to start the motor, decrease the input bias level. To reduce the signal level required to start the motor, increase the input bias level.
DANGER
UNINTENDED EQUIPMENT OPERATION If the input bias level is set too high, the drive will start the motor without a signal present at VIA or VIB. Failure to follow these instructions will result in death or serious injury. Parameters [VIA gain] (F471) and [VIB gain] (F473) are factory set so that the drive output reaches rated voltage and frequency just before the signal to VIA or VIB reaches its maximum level.
z z
To decrease the signal level required before the drive output reaches rated voltage and frequency, increase the input gain level. To increase the signal level required before the drive output reaches rated voltage and frequency, decrease the input gain level.
Note: If the input gain level is set too low, the drive output may never reach rated voltage and frequency.
S1A53838 09/2011 107
Code
Name / Description
F200
0 1
[Enable] [Disable] Switching between two speed reference sources by means of a logic input is enabled if parameter F200 is set to 0. To use this function, you need to assign a logic input to function 38, Auto/Man speed ref. When the assigned logic input is off, the drive will follow the speed reference source defined by parameter [Frequency mode sel] (FMOd) (see page 77). When the assigned logic input is on, the drive will follow the speed reference source defined by parameter [Remote spd ref 2] (F207) (see page 78). When parameter F200 is set to 1, the drive will follow the FMOd speed reference source when it is operating above 1 Hz. Below 1 Hz, it will follow the F207 speed reference source.
FMSL
Function [Motor frequency]: Output frequency [Motor current]: Output current [Speed ref]: Speed reference [DC bus U]: DC bus voltage [Motor U]: Output motor voltage [Input power]: Input power [Output power]: Output power [motor torque]: Estimated motor torque [Torque I]: Motor torque current [Motor thermal]: Motor thermal state [Drive thermal]: drive thermal state [Do not use]: DO NOT USE [Internal reference]: Internal speed
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
150 % of [DC bus U] 150 % of [Motor U] 185 % of [Input power] 185 % of [Output power] 250 % of rated motor torque Current at 250 % of rated motor torque 100 % of motors rating 100 % [Max frequency] (FH)
17 18 19
FA51 = 1000 -
FM
[AO scaling]
Parameter FM is used to match the FM terminal output signal with the input requirements of the attached panel meter by adjusting the slope and bias of the analog output signal. Before adjusting FM, set [AO funct. selection] (FMSL) to either 15 or 17. As you adjust the value of FM, monitor the display on the attached panel meter. When the meter display reaches 100%, press the ENT key on the drive embedded display terminal. The drive will flash between FM and the adjusted value, indicating that the adjustment has been saved.
108
S1A53838 09/2011
Code
Name / Description
Factory setting 1
F691
0 1
[AO slope]
[Negative slope] [Positive slope]
F692
0 to 100%
0%
Refer to the diagram below for examples of adjusting parameters [AO scaling] (FM), [AO slope] (F691), and F692.
=
(mA) 20
Output Current
=
(mA) 20
Output Current
4 0
FMSL signal value
100%
100%
=
(mA) 20
Output Current
=
(mA) 20
Output Current :Large Gain
:Small Gain
4 0
FMSL signal value
100%
100%
0 Hz
F694
Refer to the diagram below for adjusting parameters F694, and [Freq. for AO = 10V] (F695).
10 V
10 V
0V
F694
F695
0V
Speed reference Motor frequency Internal reference (after PID)
F695
F694
Speed reference Motor frequency Internal reference (after PID)
F695
0 Hz
Refer to the diagram above for adjusting parameters [Freq. for AO = 0V] (F694), and F695.
F130
For a complete description of the various functions assignable to the RYA-RYC relay, see page 98. The RYA-RYC relay can have a secondary assignment with programmed selection logic. See parameters [RY Relay Function 2] (F137) and [RY logic select.] (F139) on page 113 for more detail.
F146 F132
0.0 to 60.0 s
0.0 s
11
For a complete description of the various functions assignable to the FL relay, see page 98.
S1A53838 09/2011
109
Code
Name / Description
F147 F360
0 1 2
[No PID]: PID disabled [PID by VIA]: Enabled (feedback source is VIA) [PID by VIB]: Enabled (feedback source is VIB) Parameter F360 is used to enable PID control and define the source of the feedback signal. The PID source is defined by the setting of parameter [Frequency mode sel] (FMOd) (see page 77). Parameter [Freq band det range] (F167) can be adjusted to command a drive relay to signal when the PID setpoint and
F362
0.01 to 100.0%
0.30%
Parameter F362 adjusts the proportional gain applied during PID control. The speed change applied to the motor is a correctional value proportional to the product of this parameters setting and the process error (deviation between the setpoint and the feedback value). A higher setting of F362 provides a fast response to a process error but may also result in instability such as hunting. The diagram below illustrates the effect produced by adjusting F362.
Feedback Amount Motor Speed Change Fast Response (F362 = Large Gain) Slow Response (F362= Small Gain)
Time
F363
0.01 to 100.0
0.20
Parameter F363 adjusts the integral gain applied during PID control. Any residual process errors that remain after correction by the proportional gain are cleared to zero over time by the integral gain function. A higher setting of F363 provides a fast response to a process error but may also result in instability such as hunting. The diagram below illustrates the effect produced by adjusting F363.
Feedback Amount (F363= Small Gain)
The integral gain value can be set to zero by setting a logic input to function 65. For more information, see table on page 91 and parameters [LI F selection] (F111), [LI R selection] (F112), [LI RES selection] (F113), page 90, and [VIA LI selection] (F118), page 90.
110
S1A53838 09/2011
Code
Name / Description
F366
Parameter F366 adjusts the derivative gain applied during PID control. This gain adjusts the response time of the drive to rapid changes in the process. Increasing the setting of F366 more than necessary may cause great fluctuations in motor speed resulting in system instability. The diagram below illustrates the effect produced by adjusting F366.
F359
0 to 2400 s
If parameter F359 is set to a value greater than 0 seconds, the drive will not immediately enter PID control upon startup. For the time set by F359, the drive will ignore the feedback signal, accelerating the motor to the speed set by the reference input. This function can be used to help prevent the drive from entering PID control mode before the system approaches the final operating level.
F380
0 1
This function is used to reverse the error PI for Water Pump. If F380 = 0 or No, PI error input = reference - feedback. The motor speed increases when the error is positive. If F380 = 1 or Yes, PI error input = feedback - reference. The motor speed decreases when the error is positive.
F391
[Stop on LL hyst]
Stop on LL hysteresis
0.2 Hz
F392
0.0 Hz
DANGER
UNINTENDED EQUIPMENT OPERATION Check that unintended restarts will not endanger personnel or equipment in any way. Failure to follow these instructions will result in death or serious injury.
F393
0.0 Hz
DANGER
UNINTENDED EQUIPMENT OPERATION Check that unintended restarts will not endanger personnel or equipment in any way. Failure to follow these instructions will result in death or serious injury.
F645
0 1 2
[Disabled] [Enabled fault] (detected fault mode). If F645 is set to 1 and the PTC probe exceeds a given, threshold, the drive will trip and display an [PTC overheating] (OH2) code. [Enabled alarm] (alarm mode). If F645 is set to 2 and the PTC probe exceeds a given, threshold, the drive will signal a detected fault and continue operating. Setting parameter F645 to 1 or 2 converts control terminal VIB into a PTC motor thermal probe input. See the ATV212 Installation manual, for wiring details. 111
S1A53838 09/2011
Code
Name / Description
F646
F108 F110
0 to 73
If F110 is not set to 1 (logic function [Run permissive]), a logic input should be assigned to the [Run permissive] logic function to enable the motor to start.
Preset Speeds
A maximum of seven preset speeds can be selected by 4 logic inputs (F, R, RES, or VIA). Preset speed control is only active when the drive is in logic input control ([Command mode sel] (CMOd) = 0). For one preset speed, assign a logic input to function 6. For up to three preset speeds, use two logic inputs for functions 6 and 7. For up to seven preset speeds, use three logic inputs for functions 6, 7, and 8. Preset speed commands take priority over speed commands from any other source. For more information on preset speeds, see page 91. See page 42, for wiring instructions and timing diagram.
Code Name / Description Adjustment range LL to UL Hz Factory setting 15 Hz
[Preset speed 1] [Preset speed 2] [Preset speed 3] [Preset speed 4] [Preset speed 5] [Preset speed 6] [Preset speed 7]
LL to UL Hz
20 Hz
LL toUL Hz
25 Hz
LL to UL Hz
30 Hz
LL to UL Hz
35 Hz
LL to UL Hz
40 Hz
LL to UL Hz
45 Hz
112
S1A53838 09/2011
F264
Parameter F264 sets the maximum on-time of the logic input assigned to (+) speed, limiting the speed increase, as defined by parameter [+speed freq. step] (F265), to only one step. Keeping the logic input active longer than the time set by parameter F264 will allow multiple step increases of the speed command.
F265 F266
0.1 Hz
Parameter F265 sets the frequency width in Hz of each (+) speed command step. -Speed Logic Input Response Time] 0.0 to 10.0 s 0.1 s
Parameter F266 sets the maximum on-time of the logic input assigned to (-) speed, limiting the speed decrease, as defined by parameter [-speed freq. step] (F267), to only one step. Keeping the logic input active longer than the time set by parameter [+speed freq. step] (F265) will allow multiple step decreases of the speed command.
F267 F268
0.1 Hz
Parameter F267 sets the frequency width in Hz of each (-) speed command step. Initial +/- Speed Command 0.0 to [Max frequency] (FH) Hz 0.0 Hz
Parameter F268 sets the +/- speed command in Hz that is applied to the drive when it is first powered up. Leaving this parameter at its default value will result in the drives output frequency starting at 0 Hz every time it is powered up.
F269
0 1
[Disable] [Enable] The setting parameter F269 determines whether the value of parameter [Init +/- Speed] (F268) will change every time power is cycled to the drive. If parameter F269 is set to 1, parameter F268 will be set to the last speed command received by the drive before power was removed.
F137
255
The RYA-RYC relay can be set to signal a secondary condition. The primary RYA-RYC relay function is set by parameter [RY Relay Function 1] (F130) (see page 109). See table beginning on page 98 for a complete description of the primary and secondary functions that can be assigned to the RYA-RYC relay.
F139
0 1
[Function 1and 2]: [RY Relay Function 1] (F130) (primary) and [RY Relay Function 2] (F137) (secondary) [Function 1 or 2]: F130 (primary) or F137 (secondary) The RYA-RYC relay can be configured to energize when either: Both the primary AND secondary conditions are met (true) (F139 = 0), or Only one OR the other is met (true) (F139 = 1)
S1A53838 09/2011
113
Code
Name / Description
Adjustment range Relay Output Frequency Level 1 Attained 0.0 to [Max frequency] (FH) Hz
F100
[Freq. 1 reached]
The frequency set by parameter F100 is the threshold level for relay output functions 4 and 5 (see page 98).
Output Frequency (Hz) Commanded Frequency
Time (S)
ON OFF ON OFF
F101
[Freq. 2 reached]
0.0 Hz
The frequency set by parameter F101 +/- the [Freq.2 bandw.] (F102) detection band is the threshold level for relay output functions 8 and 9 and the hysteresis for relay output functions 66 and 67 (see page 103).
Output Frequency (Hz)
+ 0
Time (S)
ON OFF ON OFF
ON OFF ON OFF
F102
[Freq.2 bandw.]
2.5 Hz
Parameter F102 determines the bandwidth around the [Freq.2 reached] (F101) frequency (see diagram above) and the commanded frequency (see diagram below) driving relay output functions 6 through 9 (see page 98).
Output Frequency (Hz)
+
Commanded Frequency
0
Time (S)
ON OFF ON OFF
114
S1A53838 09/2011
Code
Name / Description
Adjustment range Frequency bandwidth detection range 0.0 to [Max frequency] (FH) Hz
F167
Parameter F167 determines the bandwidth around the VIA or VIB speed reference (see below) driving relay output functions 52, 53, 60, and 61 (see page 102). This function can be used to signal whether the amount of processing and the amount of feedback agree when the PID function is in use.
VIA
+
or
Time (S)
ON OFF ON OFF
F603
0 1 2
[Freewheel]: Freewheel stop [Ramp stop] [DC braking]: DC injection braking The setting of parameter F603 determines how the drive will stop if a logic input assigned to function 11 or 46 is activated (see table on pages 91 and 94).
F604
0.0 to 20.0 s
1.0 s
If parameter [Ext. fault stop Mode] (F603) is set to 2, parameter F604 will determine how long DC current will be injected into the motor while the external fault logic input is active.
S1A53838 09/2011
115
Damper control
This function applies to the ventilation ducts. The aim is to control the opening of the duct (shutter device called a "damper") when the fan starts up. Damper opening command The opening command can be assigned to a relay via the F130 or F132 parameters to the function [Damper] 68 or [Inv. damper] 69 page 103. The damper is closed automatically when there is no longer an opening command. Damper opening feedback Opening is controlled by a bit or a logic input that can be assigned via the F111 or F112 or F113 parameters to the function [Damper feedBack] 73 page 96. The corresponding logic input or bit can be configured via the parameter [Damper fdb type] F580. When there is an inconsistency, the drive goes on a [Damper fault 1] Fd1 if the damper does not open and on a [Damper fault 2] Fd2 if it does not close. The parameter [Time open damper] F581 can be used to delay tripping on an opening fault when a run command is sent and the parameter [Time close damper] F582 delays the closing fault when a stop command is sent.
Damper ATV 212
U V W
Control
0 Rp
Feedback
P24 LIp
Fan
Damper opening
M 3
Fan speed 1
0
Run command 1
Opening command 1 Rx
0
Open 1 Position of damper Closed
0
F581 F582
116
S1A53838 09/2011
Code
Name / Description
Adjustment range
Factory setting 0
F580
0 1 2 3 4
[No feedback]: No feedback used (Default value) [LI L set]: Logical input and active at level 0 (shunt). When setting F580 to 1, first assign logic inputs. [LIH set]: Logical input and active at level 1 (open). When setting F580 to 2, first assign logic inputs. [Com. LIL set]: Serial link to communication bit selected by [Com channel choice] (F807) and active at level 0 (shunt). Please refer to communcation manual. [Com. LIH set]: Serial link to communication bit selected by F807 and active at level 1 (open). Please refer to communcation manual. Setting of F580 parameter is independent of the type of command mode. The F807 parameter allows selecting the communication channel used for communication damper feedback
F581
0.05 s to 300.00 s
60.00
Opening fault monitoring time delay. If the damper is not open at the end of the set time, the drive will lock in [Damper fault 1] Fd1 detected fault mode. The timer is launch after the run command. The time delay needs to be greater than the normal opening time of the damper.
F582
0.05 s to 300.00 s
60.00
Closing fault monitoring time delay. If the damper is not close at the end of the set time, the drive will lock in [Damper fault 2] Fd2 detected fault mode. The timer is launch when the motor is stopped. The time delay needs to be greater that the normal closing time of the damper
F583
0 1 2
S1A53838 09/2011
117
118
S1A53838 09/2011
Display Parameters
Display Parameters
9
What's in this Chapter? This chapter contains the following topics:
Topic Display parameters Page 120
S1A53838 09/2011
119
Display Parameters
Display parameters
Code Name / Description Adjustment range Default graphic display option operational value 0 to 10 Factory setting 0
F710
0 1 2 3 4 5 6 7 8 9 10
[Displayed param.]
[Motor frequency] Motor operating frequency (Hz or custom display), see [Customized freq val] (F702) on page 121. [Reference] Speed reference (Hz or custom display), see F702 on page 121. [I Mot] Motor current (% or A), see [Unit value selection] (F701) below. [Drive rated I] Drive rated current (A) [Drive therm state] (%) [Motor power] Output power (kW) [Int speed ref] Internal speed reference (after PID function) (Hz or custom display, see F702 on page 121. [Com data] Serial communication data [Motor speed] Output speed (rpm, see [Motor rated speed] (F417) on page 70) [Com count] Displays the total number of frames received by the communication card since the last power ON [Com count norm st.] Displays the total number of valid frames received by the communication card since the last power ON The setting of parameter [Displayed param.] (F710) determines the default display on the drives embedded display terminal upon power up. Status alarms C, P, L, and H can only be displayed on the graphic display option if [Displayed param.] (F710) is set to 0. See Run Mode on page 23 for more information.
F701
0 1
[%] [Amp or Volt] The setting of parameter F701 determines how certain values will be displayed on the drive embedded display terminal, either as a percentage of the drive rating or as a value of amperes or volts as appropriate. The setting of F701 will only affect parameters and display values that can be represented in amperes or volts. This includes the following parameters: [Motor thermal prot.] (tHr) and F173: motor rated current F251: DC braking current level F185 and F601: motor current limit F611: underload detection level Motor rated voltage (parameters ulu and F171) are displayed in volts.
F708
0 1 to 255
Parameter F708 works along with parameter [Loc. speed ref. step] (F707) (see page 77) to adjust the incremental steps of the drive embedded display terminal frequency display. At its factory setting, parameter F708 is disabled and the embedded display terminal increments or decrements frequency displays in 0.1 Hz steps. If parameter F708 is set to a value other than 0, then the embedded display terminal frequency display is determined as follows: embedded display terminal frequency display = Internal speed reference (after PID function) x F708 / F707 For example, if both F707 and F708 are equal to 1, the embedded display terminal frequency display will increase only in 1 Hz steps.
F621
0.0 to 999.9
Parameter F621 is used in conjunction with a relay output set to functions 42 or 43 (see page 102) to signal that the run time specified by the setting of F621 has accumulated. 0.1 = 1 hour, 100 = 1000 hours
F748
0 1
The setting of parameter F748 determines whether the drives accumulated power consumption memory, displayed in kilowatthours (kWh), is cleared when the line power is cycled. If F748 is set to 0, the memory is cleared. If set to 1, the kWh memory is retained.
120
S1A53838 09/2011
Display Parameters
Code
Name / Description
Adjustment range -
F749
0 1 2 3
[1 kWh] [0.1 = 1 kWh] [0.01 = 1 kWh] [0.001 = 1 kWh] The setting of parameter F749 determines the scaling of the kWh display on the embedded display terminal.
F702
0.00 to 200.00
0.00
Parameters F702, F705, and F706 can be used to customize a speed display on the drive embedded display terminal to match the applications operational speed, for example, feet per minute or units per hour. 0.00: Frequency displayed in Hz 0.0 If parameter F702 is set to a value other than 0.00, the frequency value displayed will be calculated as follows: Value displayed = display or parameter frequency x F702. See example below. 1 to 200.0: Conversion factor
Hz
=
X
= =
Hz
=
X
= =
F703
0 1
[Frequency convert.]
[All] Frequencies display free unit [PID only] PID frequencies free unit conversion
F705
0 1
[Negative slope] [Positive slope] Parameter F705 sets the slope of the custom frequency display conversion. See the diagrams below for examples of the operation of this function.
F706
0.00 to FH Hz
0.00 Hz
Parameter F706 adds a bias to the custom frequency display conversion process.
=
graphic display option
=
graphic display option
=
1000
800
=
graphic display option
800
0
(1) See table page 167.
0 Output Frequency
80 (Hz)
S1A53838 09/2011
121
Display Parameters
122
S1A53838 09/2011
10
What's in this Chapter? This chapter contains the following topics:
Topic Time delay Catch On The Fly (F301) Overtorque Detection Nuisance Overvoltage And Input Phase Detected Fault Avoidance Motor Overload Characteristics Page 125 126 132 133 134
S1A53838 09/2011
123
Code
Name / Description
Factory setting 0
F303
DANGER
UNINTENDED EQUIPMENT OPERATION z The automatic restart can only be used on machines or installations which do not pose any danger to either personnel or equipment. z If the automatic restart is activated, the fault relay will only indicate a fault has been detected once the time-out period for the restart sequence has expired. z The equipment must be used in compliance with national and regional safety regulations Failure to follow these instructions will result in death or serious injury. 0 1 to 10 Disabled. Number of clear attempts.
Description
The table below lists the detected faults that can be cleared with Auto clear. If parameter F303 is set to a value greater than 0 and one of these detected faults occurs, the drive will attempt to automatically clear the detected fault, allowing it to be restarted:
Fault detection codes that can be cleared with the automatic restart function after the cause has disappeared
Code Fd1 OC1 OC2 OC3 OC1P OC2P OC3P OH Description Code OH2 OL1 OL2 OP1 Description
Damper detected fault 1 (closed damper) Overcurrent during acceleration Overcurrent during deceleration Overcurrent during constant speed Short-circuit or ground detected fault during acceleration Short-circuit or ground detected fault during deceleration Short-circuit or ground detected fault during constant speed operation Drive overheating
OP2 Overvoltage during deceleration OP3 Overvoltage during constant state operation SOUt Permanent magnet motor step-out
Auto clear attempts will continue until the number of attempts set by parameter F303 has been exhausted. If these attempts do not clear the detected fault condition, the drive will stop and a manual clear will be required. If another type of detected fault occurs during the auto clear process, the drive will stop and a manual clear will be required. A successful auto clear means that the drive accelerates the motor to the commanded speed without another detected fault occurring. If an unspecified period of time elapses after a successful auto clear attempt without another detected fault occurring, the reset attempt counter will clear allowing another full set of reset attempts to be made during a future detected fault occurrence. During the auto clear process, the drive embedded display terminal alternately displays rtrY and the display value selected by parameter [Displayed param.] (F710), page 120. Conditions permitting auto clear An auto clear attempt will not be made if the cause of the detected fault persists. In the case of an OL1 or OL2 overload detected fault, the drive will calculate the cooling time necessary to clear the detected fault. In the event of an OH detected fault, the heatsink temperature probe will indicate when the detected fault can be cleared. DC bus voltage measurements will indicate when an OP1, OP2, or OP3 detected fault can be cleared.
124
S1A53838 09/2011
Time delay
The first clear is attempted 1 second after the detected fault occurs. Each subsequent clear attempt adds 1 second to the time interval, as illustrated in the table below. Clear detected fault attempts
Attempt number Time delay between detected fault reset attempt and most recent fault
1 2 3 4 5 6 7 8 9 10
1 second 2 seconds 3 seconds 4 seconds 5 seconds 6 seconds 7 seconds 8 seconds 9 seconds 10 seconds
Fault relay action An output relay set to functions 10 and 11 (see table on page 98) will not indicate a detected fault until all clear attempts have been exhausted. Output relay functions 28 and 29 can be used to indicate that an auto-resetable detected fault has occurred. Output relay functions 36 and 37 can be used to signal any kind of drive detected fault, even during auto clear attempts. Drive fault memory If parameter [Drive fault memory] (F602) is set to 1 and power to the drive is cycled while an auto-resetable detected fault is active, the auto clear action will be cancelled (see page 127).
S1A53838 09/2011
125
There is a brief power loss (the embedded display terminal does not go blank) that results in the drive removing power from the motor, and, there is a continuous run command to the drive (2-wire control)
F301 Set to 1 or 3
Inout Voltage
Motor Speed
Run Command
ON OFF
The run permissive (logic input assigned to functions 1 or 54) is removed and restored, and, there is a continuous run command to the drive (2-wire control)
F301 Set to 2 or 3
Motor Speed
Run Command
ON OFF ON OFF
Run Permissive
If F301 is set to 4, the drive will perform a motor speed and direction search each time it receives a run command. Note: Enabling catch-on-the-fly adds about 300 milliseconds to implementation of each start command to the drive. Do not use catch-on-the-fly if there is more than one motor supplied by the drive.
Code Name / Description Factory setting 3 (1)
F301
0 1 2 3 4
[Catch on fly]
[Disable] [Brief power loss] After brief power loss [Run restored] After run permissive is restored [Power loss, run] After brief power loss or run permissive is restored [Each start] During every startup
F632
0
[Disabled] Cleared If parameter F632 is set to 0, the drives memory of the motors thermal state (used for overload calculation) is cleared whenever the power is cycled. [Enabled] Retained If parameter F632 is set to 1, the drives memory of the motors thermal state is retained even when power is removed. If the drive is tripped on an Motor Overload detected fault OL2, a cooling time (as calculated by the drive) needs to expire before the motor can be restarted. (1) Catch-on-the-fly motor starting after a drive detected fault is active if auto clear is enabled (parameter [Number auto reset] (F303) is not set to 0, see page 124)
126
S1A53838 09/2011
Code
Name / Description
Factory setting 0
F602
0
[Cleared] If parameter F602 is set to 0 and the drive is powered after a detected fault: If the cause of the detected fault has been removed, the drive will reset and can be started. Information about the detected fault just cleared will be transferred to the detected fault history. If the cause of the detected fault has not been removed, the detected fault will be displayed again but the drives memory of the operational information associated with the detected fault will be transferred to the detected fault history. Information about the 4th most recent detected fault will be removed from the detected fault history. [Retained] If parameter F602 is set to 1 and the drive is powered after a detected fault: If the cause of the detected fault has been removed, the drive will reset and can be started. Information about the detected fault just cleared will be transferred to the detected fault history. If the cause of the detected fault has not been removed, the original detected fault and all of its operational data will be available for viewing as the current detected fault in the monitoring mode. Information about the 4th most recent detected fault will be retained in the detected fault history. Auto clear will be disabled.
F608
0
[Disable]: Disabled If parameter F608 is set to 0, input phase loss detection is disabled. Loss of one input phase will not cause the drive to trip. [Enable]: Enabled If parameter F608 is set to 1, the loss of one input phase will cause an EPH1 detected fault.
F302
0
1 2
[Disabled] If parameter F302 is set to 0 and the drive briefly loses input power, it may not trip but may instead experience a momentary reduction of motor voltage and/or current and then resume normal operation once nominal input power is restored. [Do not use]: DO NOT SELECT [Freewheel] If parameter F302 is set to 2 and the drive briefly loses input power, the drive will remove power from the motor and allow it to coast to a stop. The embedded display terminal will flash StOP. The drive can only be restarted by providing a new run command. Input Voltage
Motor Speed
.
Code Name / Description Adjustment range Factory setting 0
F627
0
[Alarm (0.6U)]: Alarm only (detection level below 60 %) If parameter F627 is set to 0 and the supply voltage drops below 60% of its rated value, the drive will stop and indicate a detected fault code on the embedded display terminal, but it will not activate a fault relay. If the supply voltage rises above 60% of its rated value, the detected fault code on the embedded display terminal will be cleared without a clear action and the drive will be ready to operate. [Fault (0.6U)]: Fault (detection level below 60 %) If parameter F627 is set to 1 and the supply voltage drops below 60% of its rated value, the drive will trip and will require a reset action to clear the detected fault before it can be restarted. [Alarm (0.5U)]: Alarm only (detection level below 50 %) If parameter F627 is set to 2 and the supply voltage drops below 50% of its rated value, the drive will stop and indicate a detected fault code on the embedded display terminal, but it will not activate a fault relay. If the supply voltage rises above 50% of its rated value, the detected fault code on the embedded display terminal will be cleared without a clear action and the drive will be ready to operate.
CAUTION
RISK OF DAMAGE TO DRIVE When F627 = 2 , use a line choke. Failure to follow these instructions can result in death, serious injury, or equipment damage.
S1A53838 09/2011
127
Code
Name / Description
Adjustment range -
Factory setting 2
F305
0
[Enable] If parameter F305 is set to 0, and the drive detects an impending DC bus overvoltage, it will automatically take one of the following actions: Increase the deceleration time Keep the motor at a steady speed Increase the motor speed
DC Bus Voltage
1 2
[Disabled] If parameter F305 is set to 1, the drive will take no action to avoid a DC bus overvoltage. [Quick deceleration]: Enabled (quick deceleration mode) If parameter F305 is set to 2, and the drive detects an impending DC bus overvoltage, it will increase the V/Hz ratio of the power applied to the motor. Motor over-excitation is used to dissipate regenerative energy into the motor instead of the drive. [Dyn. deceleration]: Enabled (dynamic quick deceleration mode) If parameter F305 is set to 3, the drive will increase the V/Hz ratio of the power applied to the motor as soon as slow down begins instead of waiting for the DC bus voltage to approach the detected fault level. When motor speed is being reduced, a DC bus overvoltage can often be caused by regenerated energy being absorbed by the drive from the load and motor.
F626
[Overvoltage level]
140%
Parameter F626 sets the DC bus voltage level at which the actions defined by parameter F305 take place. See diagram above for more details.
128
S1A53838 09/2011
Code
Name / Description
F605
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH z If F605 = 0, loss of cable is not detected z If F605 =1 or 2, loss of cable is only detected at the startup of the motor z Check this action will not endanger personnel or equipment in any way Failure to follow these instructions will result in death or serious injury. If output phase loss detection is enabled and an output phase loss persists for more than 1 second, the drive will trip and display the EPH0 code. 0 1 [Disabled] If parameter F605 is set to 0, output phase loss detection is disabled. [First start]: At the first start-up. If parameter F605 is set to 1, an output phase loss check is made only during the first motor start-up after power is applied to the drive. [Each start]: At every start-up. If parameter F605 is set to 2, an output phase loss check is made every time the motor is started. [During run]: During operation. If parameter F605 is set to 3, continuous output phase loss monitoring is performed while the motor is running. [Permanent]: At start-up and during operation. If parameter F605 is set to 4, monitoring for an output phase loss is performed at motor start-up and continuously during operation. [Output contactor]: Load side disconnect mode. Setting 5 for parameter F605 is for applications with a load side disconnect. The drive will automatically restart the motor if the following are true: - An all-phase loss has been detected (an output contactor or a load side disconnect has opened) - The drive detects that a 3-phase connection has been reestablished (the output contactor or load side disconnect has closed). It is necessary to wait 1 s between disconnection and connection. See following scheme to have an example of loss of output contactor.
2 3 4
Speed
t Ouput contactor 1 0 t1: deceleration without ramp (freewheel) t2: acceleration with ramp
- A valid run command exists. An output phase loss detection sweep is made as part of the auto-tuning process, regardless of the setting of parameter F605. High-speed motors and other special motors may cause nuisance output phase losss.
t1
t2
S1A53838 09/2011
129
Code
Name / Description
Factory setting 0
F610
0
[Underload det.]
[Alarm] If parameter F610 is set to 0, relay output functions 24 or 25 (see page 130) can be used to signal an underload condition without the drive faulting. [Fault] If parameter F610 is set to 1 and the loading level drops below the setting of F611 for a period of time longer than that set by F612, the drive will trip, displaying code UC. The fault relay will be set if one has been defined (relay output functions 10 or 11, see page 98). A relay assigned to signal an underloaded condition (functions 24 or 25, see page 99) will also be set. The drives response to an underload condition is set by parameters F609, F610, F611, and F612. The setting of parameter F610 determines whether an underload condition signals an alarm with an output relay or faults the drive. The sum of parameters F609 and F611 determines the drive loading level that will clear an underload alarm/detected fault. Parameter F612 determines how long the drive can be under load before an alarm or detected fault is signaled. See parameters F609, F610, F611 and F612 diagram below for more details. F610 = 0 (Alarm Only)
ON Low Current Signal Output OFF OFF
F612 or Less
Time [Sec]
0 to 100% (1)
0%
0 to 255 s
0s
0 to 100% (3)
0%
[Disabled] Disabled. If parameter F633 is set to 0, the drive will not monitor for loss of signal at analog input terminal VIA [Fault detection level] If parameter F633 is set to a value greater than 0 and: The signal at VIA drops below the detection level selected, and, the low signal level persists for 300 milliseconds or longer, the drive will trip and the embedded display terminal will display the code E-18. (1) Percentage of the drives current rating. Display can also be in amperes, depending on setting of parameter [Unit value selection] (F701) (see page 120). (2) Percentage of [Underload level] (F611) setting. (3) Percentage of maximum VIA signal level
130
S1A53838 09/2011
Code
Name / Description
Factory setting 0
F644
0 1 2
[4-20 mA loss]
[No]: No [Freewheel] Freewheel. Freewheel stop and alarm. [Set speed] Fallback speed. Switch to fallback speed. Maintained as long as the trip cause is present and the run command is not disabled. See parameter [4-20mA fallback sp] (F649) for fallback speed. [Keep speed] Speed maintain. The drive maintains the speed being applied when the trip occurred, as long as the trip cause is present and the run command is not disabled. [Ramp stop] Ramp stop.
F649 F613
0 1 2 3
Fallback speed
0.0 Hz
[Each time (std)]: Each time a RUN command is given (standard pulse) [One time (std)]: Only one time after power is turned on (standard pulse) [Each time (short)]: Each time a RUN command is given (short-time pulse) [One time (short)]: Only one time after power is turned on (short-time pulse) The setting of parameter F613 determines how the drive determines an output short-circuit during start-up. Select the short-time pulse if the drive is powering a low impedance motor.
S1A53838 09/2011
131
Overtorque Detection
The drives response to a particular motor torque level is determined by the setting of parameters F615 F619.
ON Overtorque Signal Output OFF OFF
Time (Sec)
Code
Name / Description
Factory setting 0
F615
0 1
[Overtorque det.]
[Alarm] If parameter F633 is set to 0, the drive will not monitor for loss of signal at analog input terminal VIA. [Fault] If parameter F615 is set to 1 and the drive faults, the overtorque signal output will remain latched on until the detected fault is cleared. Depending on the setting of parameter F615, the drive can use output relay function 12 or 13 (see table on pages 98) to signal an overtorque alarm or detected fault (Ot code).
F616
[Overtorque level]
130%
The setting of parameter F616 determines the level at which the drive will act upon a motor overtorque condition (see diagrams above and below).
OFF
ON
OFF
ON
x 0.7 x 0.7
Output Frequency level 2
Time (Sec)
Output relay functions 20 or 21 can be used to signal a overtorque pre-alarm when the calculated motor torque reaches 70% of the value set by parameter F616.
F618
0.0 to 10 s
0.5 s
The setting of parameter F618 determines how long the drive needs to detect a motor overtorque condition before it signals an alarm or detected fault (see above diagram).
F619
[Overtorque band]
10%
While the setting of parameter F616 determines the level at which a motor overtorque alarm or detected fault will be signaled, the setting of parameter F619 determines how far the calculated motor torque needs to drop before the alarm or detected fault is cleared (see above diagram).
132
S1A53838 09/2011
Code
Name / Description
Factory setting 3
F634
1 2 3 4 5 6
[- 10 to 10 C] [11 to 20 C] [21 to 30 C] [31 to 40 C] [41 to 50 C] [51 to 60 C] The drive can be programmed to signal a service alarm using output relay functions 44 or 45 (see page 102). The status of the service alarm can be displayed on the embedded display terminal (see page 21). At initial start-up, set parameter F634 to the drives average ambient operating temperature. Setting F634 to the highest annual temperature or changing the value after drive operation has begun may result in an early drive service alarm.
High input impedance: line reactor Low input impedance: high kVA distribution network Voltage instability: generator power source
If nuisance faults occur, increase the value of parameter F481. If increasing the value of F481 over 1000 does not remove nuisance faults, increase the values of parameters F482 and F483 as needed.
Code Name / Description Adjustment range Line noise compensation filter 0 to 9999 s Factory setting 0 s
[In noise comp. filter] [In noise Inhibit filter] [In noise inhibit gain]
0 to 9999 s
442 s
0 to 300 %
100%
0.0 to 2.0 s
0.0
When the using machine has specific resonance, the following phenomena are happened:
z z
at first, set [Pwr supply adj. gain] (F484) to 0.5, next, set F484 as another value when no effect by setting F484 to 0.5, if [Motor rated freq.] (uL) = 50 Hz, set F481 to the following value 531, if uL= 60 Hz, set F481 to the following value 442.
Note: F481 and F483 are invalid when F484 has a value excluding 0.0.
S1A53838 09/2011
133
x 0.55
0 30 Hz
Set OLM to 4, 5, 6, or 7 if a forced-cooled motor is being powered by the drive. The diagram below illustrates the overload protection level for the forced-cooled motor as a function of motor frequency. Overload Protection for a Forced-Cooled Motor
Output Current Reduction Factor [%] / [A]
x 01.0 x 0.6
CAUTION
RISK OF DAMAGE TO THE MOTOR When OLM is set to 2, 3, 6 or 7 motor thermal protection is no longuer provided by the drive. Provide an alternative means of thermal protection. Failure to follow these instructions can result in equipment damage. To disable motor overload protection, set OLM to 2, 3, 6, or 7. In this case, a separate overload protective device, external to the ATV212 drive, needs to be wired between the drive and the motor. Overload Stall The overload stall function is only compatible with variable torque loads where the load on the motor and drive is dependent on the operating frequency and where the load can be reduced by slowing the motor. If overload stall is enabled, the drive will reduce its output frequency if it detects an impending overload. As the overload condition of the motor is dissipated, the drive will return its output frequency to the commanded value. To enable overload stall, set OLM to 1, 3, 5, or 7. To disable overload stall, set OLM to 0, 2, 4, or 6.
134
S1A53838 09/2011
Code
Name / Description
Factory setting 0
OLM
CAUTION
RISK OF DAMAGE TO THE MOTOR When OLM is set to 2, 3, 6?or 7 motor thermal protection is no longuer provided by the drive. Provide an alternative means of thermal protection. Failure to follow these instructions can result in equipment damage.
This parameter value depends on: - the motor type (self cool or forced cooled), - and the protection.
Protection Motor type Overload protection enabled Overload stall disabled OLM value 0 Description Behavior
In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive trips in OL2 and the letter L is flashing. In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive reduces automatically the speed and follows a fallback speed (80 % of Motor rated frequency uL) (1). If the overload remains during the fallback speed, the drive trips in OL2 and the letter L is flashing. In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive reduces automatically the speed and follows a fallback speed (80 % of Motor rated frequency uL) (1). The drive will not trip in OL2. In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive trips in OL2 and the letter L is flashing. In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive reduces automatically the speed and follows a fallback speed (80 % of Motor rated frequency uL) (1). If the overload remains during the fallback speed, the drive trips in OL2 and the letter L is flashing. In case of overload defined by [Motor thermal prot.] (tHr) parameter, the drive reduces automatically the speed and follows a fallback speed (80 % of Motor rated frequency uL) (1). The drive will not trip in OL2.
enabled
enabled
Self cooled disabled disabled disabled enabled 2 3 [Self cool] [Slf cool stall ov.load]
enabled
disabled
enabled
enabled
Forced cooled disabled disabled disabled enabled 6 7 [Forced cool] [F cool & stall ov load]
(1) If the speed is lower than the fallback speed, the drive will keep the same speed.
S1A53838 09/2011
135
136
S1A53838 09/2011
11
What's in this Chapter? This chapter contains the following topics:
Topic Network communication between the ATV212 drive and a master controller Data structure parameters Page 138 140
S1A53838 09/2011
137
WARNING
LOSS OF CONTROL The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to achieve a safe state during and after a path failure. Examples of critical control functions are emergency stop and overtravel stop. Separate or redundant control paths must be provided for critical control functions. System control paths may include communication links. Consideration must be given to the implications of unanticipated transmission delays or failures of the link (1). Failure to follow these instructions can result in death, serious injury, or equipment damage.
(1) For additional information, refer to NEMA ICS 1.1 (latest edition), Safety Guidelines for the Application, Installation, and Maintenance of Solid State Control and to NEMA ICS 7.1 (latest edition), Safety Standards for Construction and Guide for Selection, Installation and Operation of Adjustable-Speed Drive Systems.
Network communication between the ATV212 drive and a master controller is possible through five protocols selectable through the embedded display terminal:
z z z z z
Modbus RTU Metasys N2 Apogee P1 FLN BACnet LonWorks Monitoring: monitoring values such as output frequency, voltage, and current Programming: reading, editing, and writing drive parameters Control: starting and stopping the drive and controlling the frequency reference
For operation on a network containing multiple drives, each ATV212 drive needs to be assigned a unique address using parameter F802. For operation on a network where all drives are slaves responding to a central control system:
z
Parameters [Command mode sel] (CNOd) (see page 77) and [Frequency mode sel] (FMOd) (see page 77) needs to be set correctly: - Setting CMOd to 2 enables start/stop control of the drive via network communication - Setting FMOd to 4 enables the frequency reference to be controlled by network communication - Setting either CMOd to 2 or FMOd to 4 enables serial communication error detection. The setting of parameter F851 determines the drives response in case of a loss of communication.
Control of the ATV212 drive can be established by a master controller over a serial communication network regardless of the setting of CMOd or FMOd (see diagram on page 46). Control can be restored to the source defined by CMOd and FMOd if the serial communication network relinquishes control or a logic input assigned to function 48 (forced local) is enabled.
Code
Name / Description
Factory setting 1
F800
0 1
F801
0 1 2
F802
[Modbus address]
This address is used whatever the port used.
0 to 247
138
S1A53838 09/2011
Code
Name / Description
Adjustment range -
Factory setting 3
F803
WARNING
LOSS OF CONTROL z If F803 is set to 0, communication control will be inhibited. z For safety reasons, inhibiting the communication interruption detection should be restricted to the debug phase or to special applications. Failure to follow these instructions can result in death, serious injury, or equipment damage. 0 1 to 100 Communication error detection disabled 1 to 100 seconds
F820
0 1
F821
0 1 2
F829
1 2 3 4 5
[Network protocol]
[Mdb RTU] [Metasys N2] [Apogee P1] [BACnet] [LonWorks]
F829 is enable if F807 is set to 1 previously. Note: On the ATV21, Lonworks configuration corresponded to value 1.
F851
WARNING
LOSS OF CONTROL If F851 is set to 1, communication control will be inhibited. For safety reasons, inhibiting the communication interruption detection should be restricted to the debug phase or to special application. Failure to follow these instructions can result in death, serious injury, or equipment damage.
WARNING
LOSS OF CONTROL Know and understand the setting of parameter F851. This parameter controls the behavior of the drive in the event of a network communication loss. If the value of F851 is 0, 1, 2, or 3, the drive will not trip on an Err8. Failure to follow these instructions can result in death, serious injury, or equipment damage. 0 Ramp stp (F/Cmod): Drive ramps to a stop. Serial control is relinquished to the sources defined by [Frequency mode sel] (FMOd) and [Command mode sel] (CMOd). This function is only used with the Lonworks terminal board. [No active]: Last commanded operation continues. [Ramp stop]: Drive ramps to a stop. Serial control is maintained. [Freewheel]: Drive removes power from the motor which coasts to a stop. Serial control is maintained. [Err5 or Err8]: Drive faults with either a communication detected fault Err5 or a network detected fault Err8. Note: For Modbus connection, only the function 1 is taken into account. The other function make drive trip in Err8 or Err5.
1 2 3 4
F807
0 1
[RJ45]: command Modbus via RJ45 port. [Open style]: Modbus, BACnet, Apogee P1, Metasys N2 and Lonworks defined by [Network protocol] F829 via open style port. F807 can only be adjusted while the drive is stopped.
S1A53838 09/2011
139
F856
1 2 3 4 5 6 7 8
F870
0 1 2 3 4 5 6
F871
0 1 2 3 4 5 6
F875
0 1 2 3 4 5 6 7 8 9 10 11
F876
0 1 2 3 4 5 6 7 8 9 10 11
140
S1A53838 09/2011
Code
Name / Description
Factory setting 0
F877
0 1 2 3 4 5 6 7 8 9 10 11
F878
0 1 2 3 4 5 6 7 8 9 10 11
F879
0 1 2 3 4 5 6 7 8 9 10 11
Code
Name / Description
Factory setting 0
F880
S1A53838 09/2011
141
Parameters F890 F896 should be adjusted only if the corresponding optional equipment has been installed. See the ATV212 catalog for more detail.
Code F890 F891 F892 F893 F894 F895 F896 Name / Description [Network adress] [Network baud rate] [Network time out] [Instance number H] [Instance number L] [Max master] [Max info frames]
When the value of F829 parameter is changed, the adjustment range and factory setting of F890 to F896 are automatically setted.
Modbus Setting Range
F829 F890 F891 F892 F893 F894 F895 F896
APOGEE FLN P1 Setting Range 3 1 to 99 0 to 6 20 to 600 0 to 4194 0 to 999 0 to 127 0 to 100 Factory setting 3 99 0 100 0 0 0 0
METASYS N2 Setting Range 2 1 to 255 1 to 5 20 to 600 0 to 4194 0 to 999 0 to 127 0 to 100 Factory setting 2 1 5 100 0 0 0 0
BACNET Setting Range 4 0 to 127 1 to 5 20 to 600 0 to 4194 0 to 999 0 to 127 1 to 100 Factory setting 4 0 5 100 0 0 127 1
Factory setting 1 0
0 to 65535
There are 2 connection port witch support different communication protocol, embedded or using option board. The two channels could communicate simultaneously with the product, but only one could send the logical or frequency command to the drive:
z z
The two channel used for monitoring One channel used for command (run order and speed) and the second for monitoring.
The configuration parameters of communication are taking account at next power up of the product.
Description
F829 Network selection F800 Modbus RJ45 Baud rate F801 Modbus RJ45 Parity F802 Modbus address F803 Modbus time out F851 Com fault behavior F820 Modbus Net Baud rate F821 Modbus Net Parity F890 Network parameter F891 Network parameter F892 Network parameter F893 Network parameter F894 Network parameter F895 Network parameter F896 Network parameter
RJ45 Modbus p p p p p -
Network Modbus p p p p p p -
Network Apogee P1 p p p p p -
Network Metasys N2 p p p p -
Network BACnet p p p p p p p p p
142
S1A53838 09/2011
12
What's in this Chapter? This chapter contains the following topics:
Topic Overview Page 144
S1A53838 09/2011
143
Overview
Use parameters [Freq. pedestal] (F241) and [Freq. pedestal hyst.] (F242) to enable start/stop control of the drive based on the speed reference level. If the drive operates normally and has a run permissive signal, it will start powering the motor as soon as the speed reference level exceeds the frequency set by F241 + F242 (point B in diagram below). It will remove power from the motor as soon as the output frequency drops below the level set by F241 F242 (point A in diagram below).
Output Frequency (Hz)
+ 0 A B 100%
Speed Reference
Code F241
F242
0.0 Hz
144
S1A53838 09/2011
Droop Control
Droop Control
13
What's in this Chapter? This chapter contains the following topics:
Topic Droop Control Page 145
S1A53838 09/2011
145
Droop Control
The load current exceeds the level set by parameter F323. The drive output frequency is between the [Mot start freq.] F240 (see page 82) and [Max frequency] (FH) (see page 82).
Output frequency (Hz) Command frequency: f0 Operation frequency: f1 Power running
T1
100%
The amount of speed droop allowed (f) can be calculated by this equation: f = uL(1) x F320 x (load current F323)(2) Example: uL = 60 Hz F320 = 10% F323 = 30% (of drives rated current) Load current = 100% of drives rating f = 60 x 0.1 x (1 0.3) f = 60 x 0.07 f = 4.2 Assuming the speed reference is set to 60 Hz, the output frequency will be: f1 = f0 f = 60 4.2 = 55.8 (Hz).
Code Name / Description Adjustment range 0 to 100% Factory setting 0%
F320 F323
0 to 100% (3)
10%
(1) Parameter [Motor Rated freq] (uL) (see page 70). The value entered for uL in this formula should not exceed 100, regardless of the actual setting of parameter uL. (2) Speed droop is zero if (load current F323 = 0). (3) Percent of the drives rated current.
146
S1A53838 09/2011
III
What's in this Part? This part contains the following chapters:
Chapter 14 Diagnostics and troubleshooting Chapter Name Page 149
S1A53838 09/2011
147
148
S1A53838 09/2011
14
What's in this Chapter? This chapter contains the following topics:
Topic Detected fault conditions Alarm Conditions Pre-alarm Conditions Clearing the detected fault Page 150 153 154 155
S1A53838 09/2011
149
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Read and understand the instructions in Before you begin chapter, before performing the procedure in this section. Failure to follow these instructions will result in death or serious injury. Alarm Codes
Code
CFI2
Possible causes
Remedies
E-18
E-19 E-20
Check the configuration loaded previously. The configuration loaded in the drive via the Load a compatible configuration. bus or communication network is inconsistent. To perform download, uncheck "Display Transfer using PC soft has not been communication error" (in Tool / successful due to rating differences Environnement option / Startup/Comm.) (for example upload of an ATV212pppN4 configuration to an ATV212pppM3) [VIA signal fault] The VIA analog signal is below the level set Check the signal at VIA and rectify the cause by parameter F633. of the signal loss. Verify that parameter F633 is set correctly. [CPU communica Communication error between control CPUs Contact Schneider Electric to repair the tions err.] drive. [Excess torque boost Torque boost parameter Repeat the drive auto-tune and then adjust flt] [Auto Torque Boost] (F402) is set too down parameter [Auto Torque Boost] high. (F402). The motor impedance is too low. During deceleration when Set [Auto ramp] (AU1) = (0) [Disabled] [Mot cont. mode sel.] (Pt) = (1) [Quadr. U/F] Decrease the deceleration ramp with with 3 conditions: [Deceleration time 2] (F501) and - Processing for stop [Commut. ramp freq.] (F505). - Load current value > 88% x [Motor Current Limitation] (F601) - Too slow deceleration, [Max frequency] (FH) /[Deceleration time 1] (dEC) x 2 msec < 0.01Hz [CPU error 2 fault] The control board CPU is inoperable. Contact Schneider Electric to repair the drive. [EEprom pwr incom- Eeprom power incompatible. Contact Schneider Electric to repair the pat.] drive. Product hardware detected fault.
[EEPROM error 1 fault] [EEPROM error 2 fault]
Invalid configuration.
Power was removed from the drive during a Cycle power to clear the detected fault and If the detected fault does not clear, contact
Schneider Electric to repair the drive.
A data reading error has occurred. Ground fault in motor or motor cables Loss of one or more output phases
Cycle power to clear the detected fault. Check the motor and motor cables for
ground faults.
EPHI
Err1
Check parameter F608. Parameters F202, F203, F210, or Set the parameters to the correct settings.
F212 are set improperly. S1A53838 09/2011
150
Code
Err2 Err3 Err4 Err5
Name [RAM fault] [ROM fault] [CPU fault 1] [Com RJ45 fault]
Possible causes
Remedies
The control board RAM is inoperable. The control board ROM is inoperable. The control board CPU is inoperable. Serial communication error
Check network control devices and cables. Check the setting of the communication
timeout parameter, F803.
[Current sensor fault] A motor current sensor is inoperable. [Network error fault] Network communication error [Remote keypad fault] [Auto-tuning fault]
Check the setting of F829 parameters. Replace the drive. Check the network control devices and
cables.
Graphic display option cable disconnected Check the RJ45 cable. Parameters F401 to F494 are
incorrectly set. The motor is too large for the drive. The motor cable gauge is too small. The motor is still rotating at the start of the auto-tune. The drive is not powering a 3-phase induction motor. The main control board is inoperable.
Set parameters F401F494 correctly. Use a larger drive. Use a larger gauge motor cable. Verify that the motor is stopped before
starting an auto-tune.
EtYP
[Drive fault]
Set [Damper flt behavior] (F583) to 0. Check the FL relay connection (FLA/FLB). Check the relay configuration
(F130/F132).
Fd2
M020
OC1
[Overcurrent acceleration]
1.Check the FL relay connection (FLA/FLB). Check the relay configuration (F130/F132). The accumulated input power value is more Clear the accumulated input power value than 999.999 kWh. using logic input function 51, or parameter F748. The acceleration time is too short. Increase the acceleration time parameters (ACC or F500). The setting of parameter [Mot cont. mode Select the correct setting for parameter [Mot sel.] (Pt) is incorrect. cont. mode sel.] (Pt). The drive is starting into a rotating load. Enable catch on the fly, parameter F301. The drive is powering a low impedance Adjust the switching frequency parameter motor. F300. Ground fault Set parameter F316 to 1 or 3.
OC1P OC2
[SC or ground fault acc.] [Overcurrent deceleration] [SC or ground fault dec.] [Overcurrent cont. speed] [SC/ground flt cont. spd]
OC2P OC3
Set parameter F316 to 1 or 3. Using a 1000 V megger, check the motor and
motor cables for ground faults.
Reduce the load fluctuations. Check the load. Set parameter F316 to 1 or 3. Short circuit or ground fault during constant Using a 1000 V megger, check the motor and
motor cables for ground faults.
speed operation [SC inverter at start] Ground fault [SC mot. cable at start]
Phase to phase output short circuit The motor impedance is too low.
S1A53838 09/2011
151
Code
OH
Possible causes
Remedies
The drive cooling fan is not working. The ambient temperature is too high. An enclosure air vent is blocked. A heat source is too close to the drive. The drive heatsink temperature sensor is
malfunctioning.
OH2
[PTC overheating]
Correct the motor overload condition. Check the PTC for correct operation. Increase the acceleration time parameters
(ACC or F500).
OL1
[Drive overload]
OL2
[Motor overload]
Enable catch on the fly, parameter F301. Set parameter F302 to 2. Use a drive with a higher power rating. Select the correct setting for parameter [Mot
cont. mode sel.] (Pt).
[Overvoltage acceleration]
Excessive load is applied to the motor. The input voltage is fluctuating abnormally. Power network is greater than 200 kVA. Power factor capacitor switching SCR switching on power network The drive is starting into a rotating load. Intermittent output phase fault
Install a line reactor. Enable catch on the fly, parameter F301. Set parameter F302 to 2. Determine the cause of the missing output
OP2
[Overvolt. deceleration]
OP3
The input voltage is fluctuating abnormally. Install a line reactor. Power network is greater than 200 kVA Check the input and output circuits for phase loss detection and rectify. Power factor capacitor switching SCR switching on power network The drive is regenerating - the load causes
the motor to run at a frequency higher than drive output frequency. Intermittent output phase fault
phase (such as a bad connection, an output disconnect, or an open winding in the motor) and rectify the trouble. The deceleration time is too short. Increase the deceleration time parameters (DEC or F501). Overhauling load The input voltage is fluctuating abnormally. Enable parameter F305. Install a line reactor. Power network is greater than 200 kVA Check the input and output circuits for phase Power factor capacitor switching loss detection and rectify. SCR switching on power network Enable catch on the fly, parameter F301. The drive is starting into a rotating load. Intermittent output phase fault
Ot
[Overtorque]
SOUt
[PM motor step-out] The motor is jammed. (permanent magnet Output phase loss motor pulls out of Impact load synchronism) [Underload] [Undervoltage] below the level set by parameter F611.
Verify machine operation. Check the load and correct the jammed
condition.
UC UPI
The measured motor current has dropped Check parameters F610612 for the The input voltage is too low. Check the input voltage and rectify the
trouble.
152
S1A53838 09/2011
Alarm Conditions
Alarms do not cause the drive to enter a fault condition. Alarm Codes
Code Description Possible causes Remedies Atn1 [Auto tune] CLr [Reset active]
db
[DC braking]
STOP key is pressed while an detected detected fault. fault is displayed. DC braking in process The alarm code goes off in several seconds if no trouble occurs. Motor shaft fixing control
EI
Release the graphic display option held down for more than 20 seconds. key. A graphic display option key may not be If this does not clear the error, replace operating properly. the drive. The number of digits entered for values Lower the frequency free-unit such as frequencies is more than 4 (the magnification [Customized freq val] upper digits have priority). (F702). The operation panel is used to stop the Press the STOP key for an emergency
operation in automatic control or remote stop. To cancel the emergency stop, control mode. press any other key. The frequency setting signals at points 1 Set the frequency setting signals at and 2 are set too close to each other. points 1 and 2 apart from each other. Integral input power is more than Press and hold down the ENT key for 999.99 kWh. 3 s or more when power is off or when the input terminal function CKWH is turned on or displayed. Integral output power is more than Press and hold down the ENT key for 999.99 kWh. 3 s or more when power is off or when the input terminal function CKWH is turned on or displayed. The first and last data item in the auh Press MODE key to exit the data data group is displayed. group.
power
output power
OFF nSt
function, increase the frequency command above the lower-limit frequency LL+F391 or turn off the operation command. The phase-to-phase input voltage is too Measure the main circuit supply low. voltage. If the voltage is at a normal level, the drive requires repair. The ST-CC (run permissive) circuit is Close the ST-CC circuit. open. The Li is already active when the function Deactivate the active Li configured. is validated. The Li is already active when a configuration transfer is done with the function is validated. The drive is in the process of restart. The drive is operating normally if it restarts after several seconds. A momentary stop occurred.
The slowdown stop prohibition function To restart operation, reset the drive or
set with F302 (momentary power loss ride-through operation) is activated. input an operation signal again.
S1A53838 09/2011
153
Pre-alarm Conditions
Pre-alarm Codes
Code
C P
Description
The drive is at current limit. For more information, refer to parameter F601 (see page 69) and F185 (see page 74). The drive is approaching an overvoltage detected fault due to a high supply line, regenerative
motor braking, or a combination of these. For more information, refer to parameters F305 (see page 128) and F626 (see page 128). The motor overload timer has reached or exceeded 50% of its detected fault level.
L H
The pre-alarm codes are displayed, flashing on the embedded HMI, in the following order from left to right: C, P, L, H. If two or more troubles arise simultaneously, one of the following pre-alarm codes appears and flashes: CP, PL, CPL.
154
S1A53838 09/2011
CAUTION
RISK OF DAMAGE TO THE MOTOR z Repeated reset of the thermal state after a thermal overload can result in thermal stress to the motor. z When trips occur, promptly inspect the motor and driven equipment for problems (such as a locked shaft or mechanical overload) before restarting. Also check the power supplied to the motor for abnormal conditions (such as a phase loss or phase imbalance). Failure to follow these instructions can result in equipment damage.
S1A53838 09/2011
155
156
S1A53838 09/2011
Annex
Annex
IV
What's in this Part? This part contains the following chapters:
Chapter 15 17 18 Migration Parameters Reset Tables User Settings Tables Chapter Name Page 159 161 171
S1A53838 09/2011
157
Annex
158
S1A53838 09/2011
Migration
Migration
15
What's in this Chapter? This chapter contains the following topics:
Topic Migration ATV21 - ATV212 Page 160
S1A53838 09/2011
159
Migration
Make a new successful transfer Make a factory setting on the drive (using tYP parameter)
At the end of download transfer, the drive cannot run if a logic input configured to a function is active. To use the function and run the motor, it's necessary to disable and enable the logic input. Commissioning Compatible loader tool with ATV21
z
PC Soft V1.06 and higher, Multi-Loader V3.11 and higher, SoMoveMobile V2.2 and higher,
160
S1A53838 09/2011
16
Parameter Reset
Refer to Menu navigation diagram page 62 to know how to reach [Parameter reset] (tYP) parameter. The Altivar 212 drive offers three parameter reset options:
z z z
Factory reset: [Parameter reset] (tYP) = 3 50 Hz reset: [Parameter reset] (tYP) = 1 60 Hz reset: [Parameter reset] (tYP) = 2
This appendix describes parameter values after these reset operations. The following tables identify:
z z z z z
Parameters whose values after a reset do not vary by reset type, see page 162. Parameters whose values after a reset vary by reset type, see page 166. Parameters whose values after a reset are drive model dependant but do not vary by reset type, see page 167. Parameters whose values after a reset are drive model and reset type dependant, see page 168. Parameters whose values do not change if a reset is performed, see page 169.
S1A53838 09/2011
161
Description
Unit
Default Value
[Auto ramp] [Auto set function] [AO funct. selection] [AO scaling] [Parameter reset] [Local mot. direction] [Local speed ref.] [Low limit frequency] [Mot cont. mode sel.] [Motor overload prot] [Preset speed 1] [Preset speed 2] [Preset speed 3] [Preset speed 4] [Preset speed 5] [Preset speed 6] [Preset speed 7] [Freq. 1 reached] [Freq. 2 reached] [Freq.2 bandw.] [Logic Funct 1 active] [VIA selection] [Logic Funct 2 active] [LI F selection] [LI R selection] [LI RES selection] [VIA LI selection] [RY Relay Function 1] [FL Relay Function] [RY Relay Function 2] [RY logic select.] [Freq band det range] [Auto/man speed ref]f [VIB ref. point 1] [VIA freq. point 1] [VIA freq. point 2] [Remote spd ref 2] [VIB ref. point 1]
Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz % Hz % %
162
S1A53838 09/2011
Parameter
F211 F212 F240 F241 F242 F250 F251 F252 F256 F264 F265 F266 F267 F268 F269 F270 F271 F272 F273 F274 F275 F294 F295 F301 F302 F305 F307 F311 F312 F316 F320 F323 F359 F360 F362 F363 F366 F400 F401 F418 F419 F470 F471 F472 F473 F482
Description
Unit
Default Value
[VIB freq. point 1] [VIB ref. point 2] [Mot start freq.] [Freq. pedestal] [Freq. pedestal hyst.] [DC brake start freq.] [DC braking current] [DC braking time] [Time limit low spd] [+speed LI resp time] [+speed freq. step] [- speed LI resp time] [- speed freq. step] [Init +/- Speed] [Init +/- Speed memo] [Jump frequency 1] [Jump bandwidth 1] [Jump frequency 2] [Jump bandwidth 2] [Jump frequency 3] [Jump bandwidth 3] [Forced speed freq.] [Switch rem/Local] [Catch on fly] [Supply loss behav.] [Overvoltage fault] [Mot volt limitation] [Motor direction] [Noise reduction] [Switch. freq. mode] [Load gain] [Load gain offset] [PID ctrl wait time] [PID control enable] [PID Prop Gain] [PID Integral Gain] [PID Derivative Gain] [Auto-tuning drive] [Slip Compensation] [Frequency loop gain] [Freq. loop stability] [VIA bias] [VIA gain] [VIB bias] [VIB gain] [In noise Inhibit filter]
Hz % Hz Hz Hz Hz A s s s Hz s Hz Hz Hz Hz Hz Hz Hz Hz Hz % % s % s
0.0 100 0.5 0.0 0.0 0.0 50 1.0 0.0 0.1 0.1 0.1 0.1 0.0 1 0.0 0.0 0.0 0.0 0.0 0.0 50 1 3 0 2 3 1 0 1 0 10 0 0 0.30 0.20 0.00 0 50 40 20 128 148 128 148 442
163
S1A53838 09/2011
Parameter
F483 F484 F485 F492 F495 F496 F502 F503 F504 F505 F506 F507 F602 F603 F604 F605 F607 F608 F609 F610 F611 F612 F613 F615 F616 F618 F619 F621 F627 F632 F633 F634 F645 F646 F650 F691 F692 F700 F701 F702 F703 F706 F707 F708 F710 F721
Description
Unit
Default Value
[In noise inhibit gain] [Pwr supply adj. gain] [Stall control coef. 1] [Stall control coef. 2] [Motor voltage coef.] [PWM adj. coef.] [Acc/dec 1 pattern] [Acc/dec 2 pattern] [Ramp switching] [Commut. ramp freq.] [Acc/Dec S-pat start] [Acc/Dec S-pat end] [Drive fault memory] [Ext. fault stop Mode] [DC brk time ext flt] [Output phase loss] [Mot overload time] [Input phase loss] [Underload band] [Underload det.] [Underload level] [Underload det. time] [Short circuit det.] [Overtorque det.] [Overtorque level] [OvTorque det time] [Overtorque band] [Run time alarm] [Undervolt detect.] [Mot overload memo] [Loss of VIA] [Amb. temp. alarm] [Mot PTC selection] [PTC resistor value] [Forced fire control] [AO slope] [Analog output bias] [Parameter lock] [Unit value selection] [Customized freq val] [Frequency convert.] [Customize unit bias] [Loc. speed ref. step]
[Display ref. resol.]
% kHz Hz % % s s % %/A s % s % h %
100 0.0 100 100 104 14.0 0 0 1 0.0 10 10 0 0 1.0 3 300 1 10 0 0 0 0 0 130 0.5 10 610.0 (6100 h) 0 0 0 3 0 3000 0 1 0 0 1 0 0 0.0 0.0 0 0 0
S1A53838 09/2011
% Hz Hz
164
Parameter
F730 F732 F733 F734 F735 F738 F748 F800 F801 F802 F803 F829 F851 F856 F870 F871 F875 F876 F877 F878 F879 F880 F890 F891 F892 F893 F894 F895 F896
Description
Unit
Default Value
[Up/down key ref] [Loc/rem key] [Run/stop key] [Priority stop] [HMI reset button] [Quick menu AUF] [Power cons. memo] [Mdb RJ45 baud] [Mdb RJ45 parity] [Modbus address] [Com. time out] [Network protocol] [Com. fault setting] [Mot. poles (comm.)] [Block write data 1] [Block write data 2] [Block read data 1] [Block read data 2] [Block read data 3] [Block read data 4] [Block read data 5] [Free ID parameter] [Network adress] [Network baud rate] [Network time out] [Instance number H] [Instance number L] [Max master] [Max info frames]
S1A53838 09/2011
165
Description
Unit
[Command mode sel] [Frequency mode sel] [Max frequency] [Upper limit freq] [Motor rated freq.] [Mot 2 rated Freq.] [VIA freq. point 2] [VIB freq. point 2] [Number auto reset] [No load cur. coef] [In noise comp. filter]
Hz Hz Hz Hz Hz Hz % micro-seconds
0 1 50 50 50 50 50 50 0 100 0
0 1 50 50 50 50 50 50 0 0 100
0 1 60 60 60 60 60 60 0 100 0
166
S1A53838 09/2011
Parameter values that vary According to drive rating, but not reset type
The table below lists the parameters whose values, after a reset, depend on the drive model. To determine the value of a parameter after a reset, locate the drive model number in first column and read across the row to the column that corresponds to the parameter code. The number that appears at the intersection of the model number and the parameter code is the parameters value after a reset. These values are the same for every reset types ([Parameter reset] (tYP) = 1, [Parameter reset] (tYP) = 2, or [Parameter reset] (tYP) = 3). Parameters whose values after a reset are drive model dependant but do not vary by reset type
Parameter Reference ACC s ATV212H075M3X ATV212HU15M3X ATV212HU22M3X ATV212HU30M3X ATV212HU40M3X ATV212HU55M3X ATV212HU75M3X ATV212HD11M3X ATV212HD15M3X ATV212HD18M3X ATV212HD22M3X ATV212HD30M3X ATV212H075N4 ATV212HU15N4 ATV212HU22N4 ATV212HU30N4 ATV212HU40N4 ATV212HU55N4 ATV212HU75N4 ATV212HD11N4 ATV212HD15N4 ATV212HD18N4 ATV212HD22N4S ATV212HD22N4 ATV212HD30N4 ATV212HD37N4 ATV212HD45N4 ATV212HD55N4 ATV212HD75N4 10 10 10 10 10 10 10 10 10 30 30 30 10 10 10 10 10 10 10 10 10 30 30 30 30 30 30 30 30 dEC s 10 10 10 10 10 10 10 10 10 30 30 30 10 10 10 10 10 10 10 10 10 30 30 30 30 30 30 30 30 vLv V 200 200 200 200 200 200 200 200 200 200 200 200 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 ub % 6 6 5 5 5 4 3 2 2 2 2 2 6 6 5 5 5 4 3 2 2 2 2 2 2 2 2 2 2 F171 V 200 200 200 200 200 200 200 200 200 200 200 200 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 F172 % 6 6 5 5 5 4 3 2 2 2 2 2 6 6 5 5 5 4 3 2 2 2 2 2 2 2 2 2 2 F300 kHz 12 12 12 12 12 12 12 12 12 8 8 8 12 12 12 12 12 12 12 12 12 8 6 8 8 8 8 8 8 F402 % 5.8 4.3 4.1 3.7 3.4 3.0 2.5 2.3 2.0 2.0 1.8 1.8 5.8 4.3 4.1 3.7 3.4 2.6 2.3 2.2 1.9 1.9 1.8 1.8 1.8 1.8 1.7 1.6 1.5 F494 80 70 70 70 70 70 70 60 50 50 50 50 80 70 70 70 70 70 70 60 50 50 50 50 50 50 50 40 40 F626 % 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 F749 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 2 2 2 2
S1A53838 09/2011
167
Parameter values that vary According to drive rating and reset type
The table below lists lists the parameters whose values, after a reset, depend on the drive model and the reset type ([Parameter reset] (tYP) = 1, [Parameter reset] (tYP) = 2, or [Parameter reset] (tYP) = 3). To determine the value of a parameter after a reset: 1. Locate the drive model number in the first column. 2. Read across the row to the group of columns that corresponds to the reset type ([Parameter reset] (tYP) = 1, [Parameter reset] (tYP) = 2, or [Parameter reset] (tYP) = 3). 3. Locate the parameter code in the columns corresponding to the reset type. The number that appears at the intersection of the drive model number and the parameter code is the parameters value after a reset of the specified type. Parameters whose values after a reset are drive model and reset type dependant
Factory reset tYP = 3 Reference tHr % ATV212H075M3X ATV212HU15M3X ATV212HU22M3X ATV212HU30M3X ATV212HU40M3X ATV212HU55M3X ATV212HU75M3X ATV212HD11M3X ATV212HD15M3X ATV212HD18M3X ATV212HD22M3X ATV212HD30M3X ATV212H075N4 ATV212HU15N4 ATV212HU22N4 ATV212HU30N4 ATV212HU40N4 ATV212HU55N4 ATV212HU75N4 ATV212HD11N4 ATV212HD15N4 ATV212HD18N4 ATV212HD22N4S ATV212HD22N4 ATV212HD30N4 ATV212HD37N4 ATV212HD45N4 ATV212HD55N4 ATV212HD75N4 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 F173 F185 F601 % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 tHr % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50 Hz reset tYP = 1 F173 F185 F415 F416 F417 F601 % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 A 3.5 6.1 8.8 12.5 15.8 20.6 26.3 36.9 49.5 61.0 68.0 93.0 2.0 3.5 5.1 7.2 9.1 11.9 15.2 21.3 28.6 35.1 41.7 41.7 55.0 67 81 99 135 % 64 61 59 63 61 57 54 53 53 53 53 50 64 61 59 63 61 57 54 53 53 53 53 53 50 51 51 53 53 rpm 1400 1420 1430 1420 1425 1430 1450 1450 1455 1455 1460 1460 1400 1420 1430 1420 1425 1430 1450 1450 1455 1455 1460 1460 1460 1475 1475 1480 1480 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 tHr % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 60 Hz reset tYP = 2 F173 F185 F415 F416 F417 F601 % 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 A 3.0 5.8 8.0 12.4 15.2 22.0 28.0 36.0 48.0 61.0 68.0 93.0 1.5 2.9 4.0 6.2 7.6 11.0 14.0 21.0 27.0 35.1 41.7 41.7 55.0 67 71 86 114 % 60 59 61 48 51 53 42 39 36 39 36 33 60 59 61 48 51 53 42 39 36 39 36 36 33 31 34 31 31 rpm 1700 1715 1715 1760 1769 1780 1780 1766 1771 1771 1771 1771 1720 1700 1715 1715 1760 1769 1780 1780 1766 1771 1780 1771 1771 1771 1771 1771 1771 % 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110
168
S1A53838 09/2011
S1A53838 09/2011
169
170
S1A53838 09/2011
17
Use the Configuration Setting Table to look up parameter default settings, to record customized parameter settings, and to look up sections of the manual, by page number, that contain detailed parameter descriptions. Configuration Setting Table
Code FC AU1
Page 77 85
Unit Hz
0 1 2 0 1
Adjustment Range / Function [Low limit frequency] (LL) to [Upper limit freq] (UL) [Disabled] [Enable] [ACC only] [Factory set] [Run permissive] [3-wire] [+/- Speed] [4-20mA speed ref] [Logic inputs] [HMI] [Communication] [Ref source VIA] [Ref source VIB] [HMI reference] [Serial com ref.] [+/- Speed] [Motor frequency] [Motor current] [Speed ref] [DC bus U] [Motor U] [Input power] [Output power] [motor torque] [Torque I] [Motor thermal] [Drive thermal] [Do not use] [Internal reference] [VIA] [VIB] [Fixed 100%] [Fixed 50%] [Fixed 100%] [Com data] [Do not use]
User Setting
AU4
63
2 3 4 0
CMOd
77
1 2 1 2
FMOd
77
3 4 5 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
FMSL
108
FM
108
[AO scaling]
S1A53838 09/2011
171
Code
Page
Name
Unit
0 1 2 3 4 5 6 7 8 9 0 1 2 3
Adjustment Range / Function [No action] [50 Hz reset] [60 Hz reset] [Factory set] [Trip cleared] [Cumul time clear] [EtYP fault reset] [Save parameters] [Recall parameters] [Elapse time reset] [Run FW] [Run rev.] [Run FW+rev] [Run rev+FW] 0.0 3200
Factory Setting
User Setting
tYP
62
[Parameter reset]
Fr
77
0 Model dependent Model dependent 80.0 50.0 0.0 50.0 230 400
ACC
83
[Acceleration time 1]
dEC FH UL LL uL
83 82 82 82 70
[Deceleration time 1] [Max frequency] [Upper limit freq] [Low limit frequency] [Motor rated freq.]
s Hz Hz Hz Hz
0.0 3200 30.0 200.0 0.5 [Max frequency] (FH) 0.0 [Upper limit freq] (UL) 25.0 200.00
uLu
70
Pt
67
3 4 5 6
[Constant V/Hz] [Variable Torque] [Cst V/Hz+Boost] [SVC] [Economy] [Do not use] [Do not use] 0.0 30.0 10 100% of drives output current rating [Std mot. protect.] [Std & stall mot. prot] [Self cool] [Slf cool stall ov.load] [Forced cool prot] [Forc cool stall prot] [Forced cool] [F cool & stall ov load] [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) [Low limit frequency] (LL) to [Upper limit freq] (UL) 0.0 to [Max frequency] (FH) 0.0 to [Max frequency] (FH) 0.0 to [Max frequency] (FH) See table on page 91
ub tHr
68 70
% %/A
0 1 2 3 4 5 6 7
OLM
135
Sr1 Sr2 Sr3 Sr4 Sr5 Sr6 Sr7 F100 F101 F102 F108 172
112 112 112 112 112 112 112 114 114 114 112
[Preset speed 1] [Preset speed 2] [Preset speed 3] [Preset speed 4] [Preset speed 5] [Preset speed 6] [Preset speed 7] [Freq. 1 reached] [Freq. 2 reached] [Freq.2 bandw.] [Logic Funct 1 active]
Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz -
1 1 1 1 1 1 1 0 73
Code
Page
Name
Unit 0 AI LI sink
Factory Setting 0 1 2 6 10 7 4 11 255 0 0.0 0.0 0 3 0 3 2.5 50.0 230 400 Model dependant 100 110 0 0 0.0 100 50.0
User Setting
F109 F110 F111 F112 F113 F118 F130 F132 F137 F139 F146 F147 F160 F161 F162 F163 F167 F170
90 112 90 90 90 90 109 109 113 113 109 110 106 106 106 106 115 74
[VIA selection] [Logic Funct 2 active] [LI F selection] [LI R selection] [LI RES selection] [VIA LI selection] [RY Relay Function 1] [FL Relay Function] [RY Relay Function 2] [RY logic select.] [RY delay] [FL Relay delay] [VIA rel thresh. logic] [VIA threshold hyst.] [VIB rel thresh. logic] [VIB threshold hyst.] [Freq band det range] [Mot 2 rated Freq.]
s s % % % % Hz Hz
1 2 0 73 0 72 0 72 0 72 0 73
LI source See table page 162 See table page 162 See table page 162 See table page 162 See table page 162
0 61, See table page 162 254, 255 0 61, See table page 162 254, 255 0 61, See table page 162 254, 255 0 1 230V model 460V model 0 1
Function 1and 2 Function 1 or 2 0.0 60.0 s 0.0 60.0 s 0 100 0 20 0 100 0 20 0.0 to [Max frequency] (FH) 25.0 to 200.0 50 to 330 50 to 660 0 30 10 100% of drive rating 10 110% [Enable] [Disable] 0 100 0.0 200.0 0 100 0.0 200.0
F171
74
[Motor 2 Volt Boost] [Motor 2 Overload] [Mot. 2 current limit] [Auto/man speed ref] [VIA ref point 1] [VIA freq. point 1] [VIA freq. point 2] [VIA freq. point 2]
% %/A %/A % Hz % Hz
1 2
F207
78
3 4 5
[VIA] [VIB] [HMI] [Communication] [+/ Speed] 0 100 0.0 200.0 0 100 0.0 200.0
[VIB ref. point 1] [VIB freq. point 1] [VIB ref. point 2] [VIB freq. point 2] [Mot start freq.] [Freq. pedestal] [Freq. pedestal hyst.] [DC brake start freq.] [DC braking current]
% Hz % Hz Hz Hz Hz Hz %/A -
0.5 10.0 0.0 [Max frequency] (FH) 0.0 [Max frequency] (FH) 0.0 [Max frequency] (FH) 0 100%
S1A53838 09/2011
Code F252 F256 F264 F265 F266 F267 F268 F269 F270 F271 F272 F273 F274 F275 F294 F295 F300
Name [DC braking time] [Time limit low spd] [+speed LI resp time] [+speed freq. step] [- speed LI resp time] [- speed freq. step] [Init +/- Speed] [Init +/- Speed memo] [Jump frequency 1] [Jump bandwidth 1] [Jump frequency 2] [Jump bandwidth 2] [Jump frequency 3] [Jump bandwidth 3] [Forced speed freq.] [Switch rem/Local]
Unit s s s Hz s Hz Hz Hz Hz Hz Hz Hz Hz Hz 0 1
Adjustment Range / Function 0.0 20.0 [Disable] [Enable] 0.0 10.0 0.0 [Max frequency] (FH) 0.0 10.0 0.0 [Max frequency] (FH) 0.0 [Max frequency] (FH) [Disable] [Enable] 0.0 [Max frequency] (FH) 0.0 30.0 0.0 [Max frequency] (FH) 0.0 30.0 0.0 [Max frequency] (FH) 0.0 30.0 [Low limit frequency] (LL) [Upper limit freq] (UL) [No bumpless] [Bumpless] 6.0 16.0
Factory Setting 1.0 0.0 0.1 0.1 0.1 0.1 0.0 1 0.0 0.0 0.0 0.0 0.0 0.0 50.0 1 Model dependent
User Setting
0 1
0 1
85
kHz
0 1
F301
126
[Catch on fly]
F302 F303
127 124
F305
128
[Overvoltage fault]
F307
73
F311 F312
86 86
F316
86
[Disable] [Brief power loss] 2 [Run restored] 3 [Power loss, run] 4 [Each start] 0 [Disabled] 1 [Do not use] 2 [Freewheel] 0 [Disabled] 1-10 [Number of fault reset attempts] 0 [Enable] 1 [Disabled] 2 [Quick deceleration] 3 [Dyn. deceleration] 0 [Motor volt limit] 1 [Line & mot correct.] 2 [No action] 3 [U Line correction] 0 [Fw & Rev.] 1 [Fw only] 2 [Rev. only] 0 [Disable] 1 [Enable] 0 [Fixed] 1 [Auto] 2 [460 V fixed] 3 [460 V Auto] 0 1 2
0 3
1 0
[Load gain] [Load gain offset] [PID ctrl wait time] [PID control enable] [PID Prop Gain] [PID Integral Gain]
% % s -
0 100% 0 100% 0 2400 [No PID] [PID by VIA] [PID by VIB] 0.01 100.0 0.01 100.0
0 10 0 0 0.30 0.20
S1A53838 09/2011
Name [PID Derivative Gain] [PID reverse error] [Stop on LL hyst] [PID wake up (thres)] [PID wake up, feedb] [Auto-tuning drive] [Slip Compensation] [Auto Torque Boost]
Unit Hz Hz Hz % % 0 1
Adjustment Range / Function 0.00 2.55 [No] [Yes] 0.0 [Max frequency] (FH) 0.0 [Max frequency] (FH) 0.0 [Max frequency] (FH) [Disabled] [Initialize constant] [Complete tune] 0 150 0.0 30.0
Factory Setting 0.00 0 0.2 0.0 0.0 0 50 Model dependent Model dependent Model dependent Model dependent 40 20 128 148 128 148 100 0 442 100.0 0.0 100 100 Model dependant 104 14.0 20.0 20.0 0
User Setting
0 1 2
F415
70
0.1 200.0
F416
70
10.0 100.0
F417 F418 F419 F470 F471 F472 F473 F480 F481 F482 F483 F484 F485 F492 F494 F495 F496 F500 F501 F502
[Motor rated speed] [Frequency loop gain] [Freq. loop stability] [VIA bias] [VIA gain] [VIB bias] [VIB gain] [No load cur. coef] [In noise comp. filter] [In noise Inhibit filter] [In noise inhibit gain] [Pwr supply adj. gain] [Stall control coef. 1] [Stall control coef. 2] [Mot. adj coefficient] [Motor voltage coef.] [PWM adj. coef.] [Acceleration time 2] [Deceleration time 2] [Acc/dec 1 pattern]
rpm s s % kHz s s -
1 1
0 1 2 0
100 15000 1 150 1 100 0 255 0 255 0 255 0 255 100 130 0 9999 0 9999 0.0 300.0 0.0 to 2.0 10 250 50 150 DO NOT ADJUST 90 120 0.1 14.0 0.0 3200 0.0 3200 [Linear] [S-ramp 1] [S-ramp 2] [Linear] [S-pattern 1] [S-pattern 2] [Ramp 1] [Ramp 2] 0.0 [Upper limit freq] (UL) 0 50 0 50
84 85 85 84 84
[Acc/dec 2 pattern] [Ramp switching] [Commut. ramp freq.] [Acc/Dec S-pat start] [Acc/Dec S-pat end]
Hz % -
1 2 1 2
0 1 0.0 10 10
S1A53838 09/2011
175
Code
Page
Name
Unit
0 1
Adjustment Range / Function [No feedback] [LIH set] [LIL set] [Com. LIH set] [Com. LIL set] 0.05 to 300.00 s 0.05 to 300.00 s [No fault] [Freewheel stop] [Ramp stop] 10 110% [Cleared] [Retained] [Freewheel] [Ramp stop] [DC braking] 0.0 20.0 [Disabled] [First start] [Each start] [During run] [Permanent] [Catch on fly] 10 2400 [Disable] [Enable] 1 20 [Alarm] [Fault] 0 100% 0 255 [Each time (std)] [One time (std)] [Each time (short)] [One time (short)] [Alarm] [Fault] 0 250 0.0 10.0 0 100% 0.0 999.9 (0.1 = 1 hour, 100 = 1000 hours) [100 150% of nominal DC bus voltage] [Alarm (0.6U)] [Fault (0.6U)] [Alarm (0.5U)] [Disabled] [Enabled] [Disabled] [Fault detection level] [-10 to 10C] [11 to 20C] [21 to 30C] [31 to 40C] [41 to 50C] [51 to 60C]
Factory Setting
User Setting
F580
117
2 3 4
[Time open Damper] [Time close Damper] [Damper flt behavior] [Motor Current Limit] [Drive fault memory] [Ext. fault stop Mode] [DC brk time ext flt]
%/A s
0 1 2
0 1 0 1 2
0 1 2 3 4 5
F605
129
[Mot overload time] [Input phase loss] [Underload band] [Underload det.] [Underload level] [Underload det. time]
s % %/A s
0 1
300 1 10 0 0 0
0 1
0 1 2 3 0 1
F613
131
[Overtorque det.] [Overtorque level] [OvTorque det time] [Overtorque band] [Run time alarm] [Overvoltage level] [Undervolt detect.] [Mot overload memo] [Loss of VIA]
% s % h % %
1 0 1 2 0 1 0 1??? 100 1 2 3 4 5 6
F634
133
176
S1A53838 09/2011
Code
Page
Name
Unit
0 1
Adjustment Range / Function [No] [Freewheel] [Set speed] [Keep speed] [Ramp stop] [Disabled] [Enabled fault] [Enabled alarm] 100 9999 0 [Max frequency] (FH) Hz [Disable] [Enable forward] [Enable Reverse] [Enable transition 0->1] [Enable level 1] [Enable level 0] [Negative slope] [Positive slope] 0 100% 0 [Max frequency] (FH) Hz 0 [Max frequency] (FH) Hz [Unlocked] [Locked] [%] [Amp or Volt] Frequency displayed in Hz Conversion factor [All] [PID only] [Negative slope] [Positive slope] 0.00 [Max frequency] (FH) [Disable] [Enable] Disabled 0.1 Hz steps
Factory Setting
User Setting
F644
131
[4-20 mA loss]
2 3 4 0
[Mot PTC selection] [PTC resistor value] [4-20mA fallback sp] [Forced fire control]
W Hz -
1 2
0 3000 0 0
0 1 2 0
F659 F691 F692 F694 F695 F700 F701 F702 F703 F705 F706 F707 F708
79 109 109 109 109 64 120 121 121 121 121 77 120
[Forced fire function] [AO slope] [Analog output bias] [Freq. for AO = 0V] [Freq. for AO = 10V] [Parameter lock] [Unit value selection] [Customized freq val] [Frequency convert.] [Custom freq. slope] [Customize unit bias] [Loc. speed ref. step] [Display ref. resol.]
% Hz Hz Hz Hz -
1 2 0 1
0 1 0 0 0 0 1 0 0 1 0.00 0.00 0
0 1 0 1
0 0.01 200.0
0 1 0 1
0 1
F710
120
[Displayed param.]
78 80 80 80 80 80
[Loc. mot stop mode] [Up/down key ref] [Loc/rem key] [Run/stop key] [Priority stop] [HMI reset button]
1 255 See formula on page 120 0 [Motor frequency] 1 [Reference] 2 [I Mot] 3 [Drive rated I] 4 [Drive therm state] 5 [Motor power] 6 [Int speed ref] 7 [Com data] 8 [Motor speed] 9 [Com count] 10 [Com count norm st.] 0 [Ramp stop] 1 [Freewheel] 0 [Enable] 1 [Disable] 0 [Permitted memo] 1 [Prohibited] 2 [Permitted no memo] 0 [Enable] 1 [Disable] 0 [Enable] 1 [Disable] 0 [Disable] 1 [Enable]
0 0 0 0 0 1
S1A53838 09/2011
177
Page 64 120
Unit 0 1 0 1 0 1 2 3 0 1 0 1 2
Adjustment Range / Function [AUF displayed] [AUF hidden] [Disable] [Enable] [1 kWh] [0.1 kWh] [0.01 kWh] [0.001 kWh] [9600 bps] [19200 bps] [No] [Even] [Odd] 0 247 Communication error detection disabled 1 to 100 seconds [RJ45] [Open style] [9600] [19200] [No] [Even] [Odd] [Mdb RTU] [Metasys N2] [Apogee P1] [BACnet] [LonWorks] [Ramp stp (F/Cmod)] [No active] [Ramp stop] [Freewheel] [Err5 or Err8] [2 poles] [4 poles] [6 poles] [8 poles] [10 poles] [12 poles] [14 poles] [16 poles] [No select] [Command word 1] [Command word 2] [Frequency Setpoint] [Relay command] [FM command] [Speed Setpoint] [No select] [Command word 1] [Command word 2] [Frequency Setpoint] [Relay command] [FM command] [Speed Setpoint]
User Setting
F749
121
kWh
[Mdb RJ45 baud] [Mdb RJ45 parity] [Modbus address] [Com. time out] [Com channel choice] [Mdb network baud] [Mdb network parity]
s s
0 1-100
0 1 0 1 0 1 2 1 2
F829
139
[Network protocol]
3 4 5 0 1
F851
139
2 3 4 1 2 3 4 5 6 7 8 0 1 2
F856
140
F870
140
3 4 5 6 0 1 2
F871
140
3 4 5 6
178
S1A53838 09/2011
Code
Page
Name
Unit
0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11
Adjustment Range / Function [No select] [Command 1] [Freq. out] [Motor current] [Output volt] [Alarm info] [PID feedback value] [Input term. mon] [Out term. mon] [VIA monitor] [VIB monitor] [Mot speed mon.] [No select] [Command 1] [Freq. out] [Motor current] [Output volt] [Alarm info] [PID feedback value] [Input term. mon] [Out term. mon] [VIA monitor] [VIB monitor] [Mot speed mon.] [No select] [Status info] [Freq. out] [Motor current] [Output volt] [Alarm info] [PID feedback value] [Input term. mon] [Out term. mon] [VIA monitor] [VIB monitor] [Mot speed mon.] [No select] [Status info] [Freq. out] [Motor current] [Output volt] [Alarm info] [PID feedback value] [Input term. mon] [Out term. mon] [VIA monitor] [VIB monitor] [Mot speed mon.] [No select] [Status info] [Freq. out] [Motor current] [Output volt] [Alarm info] [PID feedback value] [Input term. mon] [Out term. mon] [VIA monitor] [VIB monitor] Mot speed mon. 0 65535 0 65535 0 65535
Factory Setting
User Setting
F875
140
F876
140
F877
141
F878
141
F879
141
S1A53838 09/2011
Name [Network time out] [Instance number H] [Instance number L] [Max master] [Max info frames]
Unit -
User Setting
180
S1A53838 09/2011
ATV212_programming_manual_EN_S1A53838_02 09/2011