Professional Documents
Culture Documents
Cake Pops Bakerella PDF
Cake Pops Bakerella PDF
T he Me tho ds
15
Add three-quarters of the container of frosting. (You will not need the remaining frosting.) Mix it into the crumbled cake, using the back of a large metal spoon, until thoroughly combined. If you use the entire container, the cake balls will be too moist. The mixture should be moist enough to roll into 1 12-inch balls and still hold a round shape. After rolling the cake balls by hand, place them on a wax papercovered baking sheet. Cover with plastic wrap and chill for several hours in the refrigerator, or place in the freezer for about 15 minutes. You want the balls to be firm but not frozen. Place the candy coating in a deep, microwave-safe plastic bowl. These bowls make it easier to cover the cake balls completely with candy coating while holding the bowl without burning your fingers. (I usually work with about 16 ounces of coating at a time.) Melt the candy coating, following the instructions on the package. Microwave on medium power for 30 seconds at a time, stirring with a spoon in between. You can also use a double boiler. Either way, make sure you do not overheat the coating. See Candy Coating Basics, page XX, for more on working with candy coating. Now youre ready to dip. Take a few cake balls at a time out of the refrigerator or freezer to work with. If theyre in the freezer, transfer the rest of the balls to the refrigerator at this point, so they stay firm but do not freeze. One at a time, dip about 12 inch of the tip of a lollipop stick into the melted candy coating, and then insert the lollipop stick straight into a cake ball, pushing it no more than halfway through.
48 cake pops
Youll need
18.25-ounce box cake mix 9-by-13-inch cake pan Large mixing bowl 16-ounce container ready-made frosting Large metal spoon Wax paper 2 baking sheets Plastic wrap 48 ounces (3 pounds) candy coating Deep, microwave-safe plastic bowl 48 paper lollipop sticks Styrofoam block (see Tips, page 16)
Bake the cake as directed on the box, using a 9-by-13-inch cake pan. Let cool completely. Once the cake is cooled, get organized and set aside plenty of time (a couple of hours) to crumble, roll, and dip 4 dozen cake pops. Crumble the cooled cake into a large mixing bowl. See Crumbling Your Cake on page XX. You should not see any large pieces of cake.
(continued)
16
cake po ps
Holding the lollipop stick with cake ball attached, dip the entire cake ball into the melted candy coating until it is completely covered, and remove it in one motion. Make sure the coating meets at the base of the lollipop stick. This helps secure the cake ball to the stick when the coating sets. The object is to completely cover the cake ball and remove it without submerging it in the coating more than once. A small, deep plastic bowl is very helpful during this step. If you do resubmerge the cake pop, the weight of the candy coating can pull on the cake ball and cause it to get stuck in the coating. The thinner the consistency of your coating, the easier it will be to coat the cake pops. If you find that your coating is too thick, add some shortening or paramount crystals (see page 40) to help thin it and make the coating more fluid. When you remove the cake pop from the candy coating, some excess coating may start to drip. Hold the cake pop in one hand and use the other hand to gently tap the first wrist. Rotate the lollipop stick if necessary to allow the excess coating to fall off evenly, so one side doesnt get heavier than the other. If you didnt completely dunk the cake pop, this method of tapping and rotating generally takes care of that. The coating will slowly slide down the surface of the cake ball until it reaches the lollipop stick. If too much coating surrounds the base of the lollipop stick, you can wipe the excess off with your finger. Simply place your finger on the stick right under the cake ball and spin the lollipop stick, allowing any excess coating to fall off and back into the bowl of coating. When most of the excess coating has fallen off and it is no longer dripping, stick the cake pop into the prepared Styrofoam block. Repeat with the remaining cake balls and let dry completely. Store the cake pops in an airtight container on the counter or in the refrigerator for several days. You can also cover them in small treat bags, tied with a ribbon, and leave them in the Styrofoam block on the counter.
Tips Make the cake the day before and let it cool overnight. U se a toothpick to encourage the coating to cover any small
exposed areas or to make sure it surrounds the lollipop stick.
M ake sure the cake balls are chilled and firm when you dip
them. If they are room temperature, they are likely to fall off the lollipop sticks into the melted candy coating. You can always place them back in the freezer for a few minutes to quickly firm them up again.
F or fun, experiment with different colors of candy coating. C ake pops need more attention and therefore a little more
time to complete than the cake balls. Set aside a couple of hours.
W hen using the cake pop method, you can also make the
balls in different shapes. Just roll them into balls, place in the freezer or refrigerator to firm, and then mold into your desired shape.
Ca k e Po p Projec ts
67
Have the cake balls chilled and in the refrigerator. Cut off the tops of the sugar cones, using a serrated knife, so that the width of the opening is about 1 1 4 inches. Prepare your Styrofoam block. Since these have cone-shaped bottoms, youll need to do more than just poke holes in the Styrofoam to support them. Take a lollipop stick, insert it at an angle, and then work it around in a circular motion until you have an opening in the Styrofoam that mimics the bottom shape of the cones. Melt the pink candy coating in a microwave-safe plastic bowl, following the instructions on the package. The coating should be about 3 inches deep. (I usually work with about 16 ounces of coating at a time.) When you are ready to coat, remove a few cake balls at a time from the refrigerator, keeping the rest chilled. One at a time, cover a cake ball with the melted coating as described on page 36. Then insert a lollipop stick into the ball to lift it out. Transfer the coated cake ball to the prepared ice cream cone, and remove the stick. Dont worry about any excess coating or the hole left by the stick.
Youll need
48 uncoated Basic Cake Balls (page 11) 48 sugar cones Serrated knife Styrofoam block Several lollipop sticks 48 ounces (3 pounds) pink candy coating 2 deep, microwave-safe plastic bowls Multicolor sprinkles 16 ounces dark chocolate candy coating Spoon 48 red peanut M&Ms
(continued)
68
CAke Po ps
The coated cake ball should rest nicely in the opening of the ice cream cone, and any excess coating will only enhance the look as it drips slightly down the edge. If the cake balls dont fit just right, make another cut in the cones so the opening is smaller, or make the cake balls bigger. Decorate with sprinkles while the pink candy coating is still wet. Place the cones in the Styrofoam block to dry completely. Melt the dark chocolate candy coating in the second microwave-safe plastic bowl. Spoon just a small amount over the very top of the ice cream cone. One at a time, attach a red peanut M&M on top before the chocolate coating sets, and return to the Styrofoam block to dry.
Tips You can reserve the unused sugar cone tops for the Easter
Baskets project on page 61.