Professional Documents
Culture Documents
ACS712 Datasheet
ACS712 Datasheet
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Features and Benefits
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 s output rise time in response to step input current 80 kHz bandwidth Total output error 1.5% at TA = 25C Small footprint, low-profile SOIC8 package 1.2 m internal conductor resistance 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 5.0 V, single supply operation 66 to 185 mV/A output sensitivity Output voltage proportional to AC or DC currents Factory-trimmed for accuracy Extremely stable output offset voltage Nearly zero magnetic hysteresis Ratiometric output from supply voltage
Description
The Allegro ACS712 provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, switchmode power supplies, and overcurrent fault protection. The device is not intended for automotive applications. The device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional voltage is provided by the low-offset, chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy after packaging. The output of the device has a positive slope (>VIOUT(Q)) when an increasing current flows through the primary copper conduction path (from pins 1 and 2, to pins 3 and 4), which is the path used for current sampling. The internal resistance of this conductive path is 1.2 m typical, providing low power loss. The thickness of the copper conductor allows survival of
Continued on the next page
Typical Application
+5 V 1 2 IP 3 4 IP+ VCC 8 7 VOUT CBYP 0.1 F
6 5 CF 1 nF
Application 1. The ACS712 outputs an analog signal, VOUT . that varies linearly with the uni- or bi-directional AC or DC primary sampled current, IP , within the range specified. CF is recommended for noise management, with values that depend on the application. ACS712-DS, Rev. 15
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Description (continued) the device at up to 5 overcurrent conditions. The terminals of the conductive path are electrically isolated from the signal leads (pins 5 through 8). This allows the ACS712 to be used in applications requiring electrical isolation without the use of opto-isolators or other costly isolation techniques.
The ACS712 is provided in a small, surface mount SOIC8 package. The leadframe is plated with 100% matte tin, which is compatible with standard lead (Pb) free printed circuit board assembly processes. Internally, the device is Pb-free, except for flip-chip high-temperature Pb-based solder balls, currently exempt from RoHS. The device is fully calibrated prior to shipment from the factory.
Selection Guide
Part Number ACS712ELCTR-05B-T ACS712ELCTR-20A-T ACS712ELCTR-30A-T Packing* Tape and reel, 3000 pieces/reel Tape and reel, 3000 pieces/reel Tape and reel, 3000 pieces/reel TA (C) 40 to 85 40 to 85 40 to 85 Optimized Range, IP (A) 5 20 30 Sensitivity, Sens (Typ) (mV/A) 185 100 66
Isolation Characteristics
Characteristic Dielectric Strength Test Voltage* Working Voltage for Basic Isolation Working Voltage for Reinforced Isolation Symbol VISO VWFSI VWFRI Notes Agency type-tested for 60 seconds per UL standard 60950-1, 1st Edition For basic (single) isolation per UL standard 60950-1, 1st Edition For reinforced (double) isolation per UL standard 60950-1, 1st Edition Rating 2100 354 184 Unit VAC VDC or Vpk VDC or Vpk
* Allegro does not conduct 60-second testing. It is done only during the UL certification process.
Specification
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
IP+ (Pin 1)
IP+ (Pin 2)
Signal Recovery
RF(INT)
VIOUT (Pin 7)
IP (Pin 3) IP (Pin 4)
GND (Pin 5)
FILTER (Pin 6)
Pin-out Diagram
IP+ IP+ IP IP 1 2 3 4 8 7 6 5 VCC VIOUT FILTER GND
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
COMMON OPERATING CHARACTERISTICS1 over full range of TA , CF = 1 nF, and VCC = 5 V, unless otherwise specified
Characteristic Supply Voltage Supply Current Output Capacitance Load Output Resistive Load Primary Conductor Resistance Rise Time Frequency Bandwidth Nonlinearity Symmetry Zero Current Output Voltage Power-On Time Magnetic Coupling2 Internal Filter Resistance3
1Device
Symbol VCC ICC CLOAD RLOAD RPRIMARY tr f ELIN ESYM VIOUT(Q) tPO RF(INT)
Test Conditions
Min. 4.5
ELECTRICAL CHARACTERISTICS VCC = 5.0 V, output open VIOUT to GND VIOUT to GND TA = 25C IP = IP(max), TA = 25C, COUT = open 3 dB, TA = 25C; IP is 10 A peak-to-peak Over full range of IP Over full range of IP Bidirectional; IP = 0 A, TA = 25C Output reaches 90% of steady-state level, TJ = 25C, 20 A present on leadframe 4.7 98
may be operated at higher primary current levels, IP, and ambient, TA , and internal leadframe temperatures, TA , provided that the Maximum Junction Temperature, TJ(max), is not exceeded. 21G = 0.1 mT. 3R F(INT) forms an RC circuit via the FILTER pin.
Typ.
Max. 85 Value 5 23
TA RJL RJA
40
Mounted on the Allegro 85-0322 evaluation board, includes the power consumed by the board
thermal information is available on the Allegro website. evaluation board has 1500 mm2 of 2 oz. copper on each side, connected to pins 1 and 2, and to pins 3 and 4, with thermal vias connecting the layers. Performance values include the power consumed by the PCB. Further details on the board are available from the Frequently Asked Questions document on our website. Further information about board design and thermal performance also can be found in the Applications Information section of this datasheet.
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
x05B PERFORMANCE CHARACTERISTICS1 TA = 40C to 85C, CF = 1 nF, and VCC = 5 V, unless otherwise specified
Characteristic Optimized Accuracy Range Sensitivity Noise Zero Current Output Slope Sensitivity Slope Total Output Error2
1Device
Test Conditions Over full range of IP, TA = 25C Peak-to-peak, TA = 25C, 185 mV/A programmed Sensitivity, CF = 47 nF, COUT = open, 2 kHz bandwidth TA = 40C to 25C TA = 25C to 150C TA = 40C to 25C TA = 25C to 150C IP =5 A, TA = 25C
Min. 5 180
Max. 5 190
may be operated at higher primary current levels, IP, and ambient temperatures, TA, provided that the Maximum Junction Temperature, TJ(max), is not exceeded. 2Percentage of I , with I = 5 A. Output filtered. P P
x20A PERFORMANCE CHARACTERISTICS1 TA = 40C to 85C, CF = 1 nF, and VCC = 5 V, unless otherwise specified
Characteristic Optimized Accuracy Range Sensitivity Noise Zero Current Output Slope Sensitivity Slope Total Output Error2
1Device
Test Conditions Over full range of IP, TA = 25C Peak-to-peak, TA = 25C, 100 mV/A programmed Sensitivity, CF = 47 nF, COUT = open, 2 kHz bandwidth TA = 40C to 25C TA = 25C to 150C TA = 40C to 25C TA = 25C to 150C IP =20 A, TA = 25C
Min. 20 96
Max. 20 104
may be operated at higher primary current levels, IP, and ambient temperatures, TA, provided that the Maximum Junction Temperature, TJ(max), is not exceeded. 2Percentage of I , with I = 20 A. Output filtered. P P
x30A PERFORMANCE CHARACTERISTICS1 TA = 40C to 85C, CF = 1 nF, and VCC = 5 V, unless otherwise specified
Characteristic Optimized Accuracy Range Sensitivity Noise Zero Current Output Slope Sensitivity Slope Total Output Error2
1Device
Test Conditions Over full range of IP , TA = 25C Peak-to-peak, TA = 25C, 66 mV/A programmed Sensitivity, CF = 47 nF, COUT = open, 2 kHz bandwidth TA = 40C to 25C TA = 25C to 150C TA = 40C to 25C TA = 25C to 150C IP = 30 A , TA = 25C
Min. 30 63
Max. 30 69
may be operated at higher primary current levels, IP, and ambient temperatures, TA, provided that the Maximum Junction Temperature, TJ(max), is not exceeded. 2Percentage of I , with I = 30 A. Output filtered. P P
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Characteristic Performance
IP = 5 A, unless otherwise specified
10.9 10.8 10.7 ICC (mA) 10.6 10.5 10.4 10.3 10.2 10.1 -25 0 25 50 TA (C) 75 100 125 150 10.0 4.5 4.6 4.7 4.8 4.9 5.0 5.1 VCC (V) 5.2 5.3 5.4 5.5 VCC = 5 V
25
25
50 TA (C)
75
100
125
150
25
25
50 TA (C)
75
100
125
150
200.00 190.00 180.00 170.00 160.00 150.00 140.00 130.00 120.00 110.00 100.00 -6
TA (C) 40 25 85 150
-4
-2
IP (A)
0 Ip (A)
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Characteristic Performance
IP = 20 A, unless otherwise specified
10.4 10.2 ICC (mA) 10.0 9.8 9.6 9.4 9.2 9.0 4.5 4.6 4.7 4.8 4.9 5.0 5.1 VCC (V) 5.2 5.3 5.4 5.5
-25
25
50 TA (C)
75
100
125
150
99.0 50
25
25
50 TA (C)
75
100
125
150
90.00 25 20 15 10
5 0 Ip (A)
10
15
20
25
IP = 0 A
IP = 0 A
50 TA (C)
75
100
125
150
0.15 -50
-25
25
50 TA (C)
75
100
125
150
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Characteristic Performance
IP = 30 A, unless otherwise specified
10.2 10.0 ICC (mA) 9.8 9.6 9.4 9.2 9.0 4.5
-25
25
50 TA (C)
75
100
125
150
4.6
4.7
4.8
4.9
5.2
5.3
5.4
5.5
65.7 50
25
25
50 TA (C)
75
100
125
150
60.00 30
IP = 0 A
IP = 0 A
50 TA (C)
75
100
125
150
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Accuracy is divided into four areas: 0 A at 25C. Accuracy at the zero current flow at 25C, without the effects of temperature. 0 A over temperature. Accuracy at the zero current flow including temperature effects. Full-scale current at 25C. Accuracy at the the full-scale current at 25C, without the effects of temperature. Full-scale current over temperature. Accuracy at the fullscale current flow including temperature effects. Ratiometry. The ratiometric feature means that its 0 A output, VIOUT(Q), (nominally equal to VCC/2) and sensitivity, Sens, are proportional to its supply voltage, VCC . The following formula is used to derive the ratiometric change in 0 A output voltage, VIOUT(Q)RAT (%).
100 VIOUT(Q)VCC / VIOUT(Q)5V
{ [
[{
VCC / 5 V
where VIOUT_full-scale amperes = the output voltage (V) when the sampled current approximates full-scale IP . Symmetry (ESYM). The degree to which the absolute voltage output from the IC varies in proportion to either a positive or negative full-scale primary current. The following formula is used to derive symmetry:
100 VIOUT_+ full-scale amperes VIOUT(Q)
VCC / 5 V
Quiescent output voltage (VIOUT(Q)). The output of the device when the primary current is zero. For a unipolar supply voltage, it nominally remains at VCC 2. Thus, VCC = 5 V translates into VIOUT(Q) = 2.5 V. Variation in VIOUT(Q) can be attributed to the resolution of the Allegro linear IC quiescent voltage trim and thermal drift. Electrical offset voltage (VOE). The deviation of the device output from its ideal quiescent value of VCC / 2 due to nonmagnetic causes. To convert this voltage to amperes, divide by the device sensitivity, Sens. Accuracy (ETOT). The accuracy represents the maximum deviation of the actual output from its ideal value. This is also known as the total output error. The accuracy is illustrated graphically in the output voltage versus current chart at right.
IP (A)
Average VIOUT
Full Scale
IP(max)
0A
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Power-On Time (tPO). When the supply is ramped to its operating voltage, the device requires a finite time to power its internal components before responding to an input magnetic field. Power-On Time, tPO , is defined as the time it takes for the output voltage to settle within 10% of its steady state value under an applied magnetic field, after the power supply has reached its minimum specified operating voltage, VCC(min), as shown in the chart at right.
Rise time (tr). The time interval between a) when the device reaches 10% of its full scale value, and b) when it reaches 90% of its full scale value. The rise time to a step response is used to derive the bandwidth of the device, in which (3 dB) = 0.35 / tr. Both tr and tRESPONSE are detrimentally affected by eddy current losses observed in the conductive IC ground plane.
I (%) 90
Primary Current
Step Response
TA=25C
tPO (s)
10
20
CF (nF)
30
40
50
Output (mV) 15 A
Excitation Signal
10000 1000
Noise(p-p) (mA)
100 10 1 0.01
0.1
CF (nF)
10
100
Rise Time versus External Filter Capacitance CF (nF) Open 1 4.7 22 47 100 220 470 1000 tr (s) 3.5 5.8 17.5 73.5 88.2 291.3 623 1120 tr(s)
}
1 10 CF (nF) 100
1 CF (nF)
10
100
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
10
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Regulator
Amp
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
11
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Typical Applications
+5 V +5 V VPEAK C2 0.1 F R4 10 k CBYP 0.1 F VRESET Q1 2N7002 1 2 IP+ VCC 8 7 RF 1 k 6 5 CF 0.01 F R1 100 k
CBYP 0.1 F
1 2 IP 3 4
IP+
VCC
8 7 RF 10 k 6 5
R2 100 k
1 3
5 2
LM321 4 VOUT
+
D1 U1 LT1178 1N914 IP
R1 1 M CF 1 nF R2 33 k
3 4 R3 330 k C1 0.1 F
IP FILTER IP GND
R3 3.3 k
C1 1000 pF
Application 3. This configuration increases gain to 610 mV/A (tested using the ACS712ELC-05A). Application 2. Peak Detecting Circuit
+5 V CBYP 0.1 F CBYP 0.1 F 8 7 R1 33 k RPU 100 k +5 V
R2 100 k VOUT 4 3
1 2 IP 3 4
IP+
VCC
8 7 VOUT RF 2 k 6 5 R1 10 k CF 1 nF
D1 1N4448W
1 A-to-D Converter IP 2
IP+
VCC
Fault
C1
3 4
IP FILTER IP GND
6 5 CF 1 nF
2 U1 LMV7235
D1 1N914
Application 4. Rectified Output. 3.3 V scaling and rectification application for A-to-D converters. Replaces current transformer solutions with simpler ACS circuit. C1 is a function of the load resistance and filtering desired. R1 can be omitted if the full range is desired.
Application 5. 10 A Overcurrent Fault Latch. Fault threshold set by R1 and R2. This circuit latches an overcurrent fault and holds it until the 5 V rail is powered down.
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
12
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Improving Sensing System Accuracy Using the FILTER Pin In low-frequency sensing applications, it is often advantageous to add a simple RC filter to the output of the device. Such a lowpass filter improves the signal-to-noise ratio, and therefore the resolution, of the device output signal. However, the addition of an RC filter to the output of a sensor IC can result in undesirable device output attenuation even for DC signals. Signal attenuation, VATT , is a result of the resistive divider effect between the resistance of the external filter, RF (see Application 6), and the input impedance and resistance of the customer interface circuit, RINTFC. The transfer function of this resistive divider is given by:
VATT = VIOUT
temperature. Therefore, signal attenuation will vary as a function of temperature. Note that, in many cases, the input impedance, RINTFC , of a typical analog-to-digital converter (ADC) can be as low as 10 k. The ACS712 contains an internal resistor, a FILTER pin connection to the printed circuit board, and an internal buffer amplifier. With this circuit architecture, users can implement a simple RC filter via the addition of a capacitor, CF (see Application 7) from the FILTER pin to ground. The buffer amplifier inside of the ACS712 (located after the internal resistor and FILTER pin connection) eliminates the attenuation caused by the resistive divider effect described in the equation for VATT. Therefore, the ACS712 device is ideal for use in high-accuracy applications that cannot afford the signal attenuation associated with the use of an external RC low-pass filter.
VCC Pin 8
RINTFC RF + RINTFC
Even if RF and RINTFC are designed to match, the two individual resistance values will most likely drift by different amounts over
+5 V Pin 3 Pin 4 IP IP
Allegro ACS706
Application 6. When a low pass filter is constructed externally to a standard Hall effect device, a resistive divider may exist between the filter resistor, RF, and the resistance of the customer interface circuit, RINTFC. This resistive divider will cause excessive attenuation, as given by the transfer function for VATT.
Resistive Divider
Input
Filter
Amp
Out
0.1 MF
N.C. Pin 6
RF
Gain
Offset
CF 1 nF
RINTFC
Trim Control
GND Pin 5
+5 V VCC Pin 8
Application 7. Using the FILTER pin provided on the ACS712 eliminates the attenuation effects of the resistor divider between RF and RINTFC, shown in Application 6.
Allegro ACS712
Hall Current Drive
IP Pin 3 IP Pin 4
RINTFC
GND Pin 5
FILTER Pin 6
CF 1 nF
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
13
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
4.90 0.10 8
0.65 1.75
1.27
5.60
1.27 0.40 0.25 BSC Branded Face SEATING PLANE GAUGE PLANE
C
B Standard Branding Reference View For Reference Only; not for tooling use (reference MS-012AA) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area B Branding scale and appearance at supplier discretion
C D
N = Device part number T = Device temperature range P = Package Designator A = Amperage L = Lot number Belly Brand = Country of Origin
Reference land pattern layout (reference IPC7351 SOIC127P600X175-8M); all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
14
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Revision History
Revision Rev. 15 Revision Date November 16, 2012 Description of Revision Update rise time and isolation, IOUT reference data, patents
Copyright 2006-2013, Allegro MicroSystems, LLC The products described herein are protected by U.S. patents: 5,621,319; 7,598,601; and 7,709,754. Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegros products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website: www.allegromicro.com
Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
15