Asna 2531 2006-09 K 2
Asna 2531 2006-09 K 2
Issue :
K Sep 06 1/7
Date : Page :
SUMMARY
1 - SCOPE AND FIELD OF APPLICATION 2 - REFERENCES 3 - TERMINOLOGY 4 - REQUIRED CHARACTERISTICS 5 - DESIGNATION 6 - MARKING 7 - TECHNICAL SPECIFICATION 8 - MANUFACTURERS AMENDMENT RECORD SHEET
1 -
SCOPE AND FIELD OF APPLICATION This standard specifies the dimensions, tolerances, required characteristics and the masses of a self-locking hexagonal nut.
2 -
REFERENCES ABS1420 AMS4928 AMS4967 AMS6322 AMS6415 AMS-QQ-P-416 AMS-S-5000 ASMEB46-1 ASNA2846 EN2424 EN4473 : Nut - Ordinary, for lightweight threaded pins. : Titanium alloys bars, wire, forgings, and rings 6AL-4V annealed. : Titanium alloys bars, wire, forgings, and rings 6AL-4V annealed, heat treatable. : Steel Bars, Forgings, and Rings (SAE 8740). : Steel Bars, Forgings, and Tubing (SAE 4340). : Plating, cadmium (electrodeposited). : Steel, Chrome-Nickel-Molybdenum (E4340) Bars and Reforging Stock. : Surface texture (surface roughness, waviness, and lay). : Material Equivalent, for fasteners. : Aerospace series - Marking of aerospace products. : Aerospace series Aluminium pigmented coatings Technical specification.
The content of this document is the property of AIRBUS FRANCE. It is supplied in confidence and commercial security on its contents must be maintained. It must not be used for any purpose other than that for which it is supplied nor may information contained in it be disclosed to unauthorized persons. It must not be reproduced in whole or in part without permission in writing from AIRBUS FRANCE. AIRBUS FRANCE Trade Secrets or Commercial or Financial information, 5 U.S.C. (b) (4).
AIRBUS FRANCE 1988. All rights reserved DocMaster: Uncontrolled copy when printed
ASNA2531
Issue : Page : Sep 06 2
: Specification for lubrication of bolts with cetyl alcohol. : Nut, self-locking, 250 F, 450 F, 800 F. : Screw threads UNJ profile, inch - Controlled radius root with increased minor diameter.
3 -
4 -
REQUIRED CHARACTERISTICS 4.1 - Configuration, dimensions, tolerances, mass 4.1.1 - Configuration shall be in accordance with the figure. 4.1.2 - Dimensions shall be in accordance with the figure and table 1. All dimensions are given after finish, but before lubrication. 4.1.3 - Tolerances shall be in accordance with table 1. 4.1.4 - Mass shall be in accordance with table 1. 4.2 - Material, finish, lubrication Material, finish and lubrication shall be in accordance with table 2. 4.3 - General characteristics 4.3.1 - Max. operating temperature : +235 C for steel nut and +315 C for titanium nut. 4.3.2 - Surface conditions as per ASMEB46-1 - Bearing surfaces (washer and nut spherical radius, ) Ra 3,2 m. - Other surfaces Ra 3,2 m.
ASNA2531
Issue : Page : Sep 06 3
Chamfer or radius R S M Optional form Marking see chapter 6 W Identification for material and finish (see table 2)
Detail A
Dimensions in mm. Note: Tool mark or distortion permissible in the locking area. Figure - Configuration, dimensions
ASNA2531
Issue : Page : Sep 06 4
Table 1 - Dimensions, tolerances, mass THREAD A C H M r S min. W 1) R Min. AXIAL MASS D min. CODE as per max. Ref. = max. max. TENSILE (kg/1 000 parts) 0,254 min. Ref. No. SAE U min. min. min. STRENGTH For information Steel Titan. AS8879 only (daN) Steel 2 .1640-32 UNJC-3B .1900-32 UNJF-3B .2160-28 UNJF-3B .2500-28 UNJF-3B .3125-24 UNJF-3B .3750-24 UNJF-3B .4375-20 UNJF-3B .5000-20 UNJF-3B .5625-18 UNJF-3B .6250-18 UNJF-3B .7500-16 UNJF-3B .8750-14 UNJF-3B 1.0000-12 UNJF-3B 7,37 6,36 4,20 5,84 2,25 0,5 TBD 5,66 5,36 2,06 0,8 3A 10,00 8,30 6,15 6,70 2,39 2,46 7,19 0,30 6,88 0,10 2,80 1,0 5 13,59 10,90 8,74 8,82 8,31 2,69 3,00 9,55 9,32 3,50 12,75 12,50 4,00 14,32 0,85 14,05 0,20 4,28 17,45 17,07 4,86 3,00 10 25,40 23,87 16,87 14,20 1,6 12 31,10 25,40 22,10 16,90 3,40 6,35 22,30 21,90 9,20 27,00 26,70 1,20 10,52 30,23 0,50 29,90 20 865 39,800 24,490 6,70 20,86 1,00 20,48 0,30 14 234 22,200 13,660 19,05 18,67 3 600 3,500 2,150 7,95 7,75 1 700 1,800 1,108 6,37 6,17 880 1,000 Titan. 0,620
9,02
7,24
5,66
6,30
2,54
1 240
1,200
0,740
7,23
7,11
2,64
2 350
2,000
1,230
9,30
2,74 1,2
5 800
7,100
4,370
7 600
10,100
6,220
11,30 2,90
10 200
15,700
9,660
23,50 21,73
15,29
12,80
12 900
18,700 11,510
14
38,10 30,80
26,30
22,00 3,70
28 123
88,900 54,710
16
43,10 34,50
30,20
25,00 4,00
38 101
130,180 80,110
1) Dimensions shall be applicable prior to incorporation of the locking feature (as per NASM25027). Dimensions in mm.
ASNA2531
Issue : Page : Sep 06 5
Table 2 - Material, finish, lubrication MATERIAL AND FINISH CODE MATERIAL Alloy steel 8740 as per AMS6322 or 4340 as per AMS6415 or AMS-S-5000 or equivalent as per ASNA2846 Hardness 39-43 HRC Titanium alloy 6AL-4V as per AMS4928 or AMS4967 Rc min. = 590 MPa R min. = 900 MPa (annealed) White paint on the top of nut (see the figure) Cadmium plating as per AMS-QQ-P-416 type II, class 2 Cetyl alcohol as per EN6117 FINISH LUBRICATION IDENTIFICATION
None
5 -
DESIGNATION Example of part number identification to be used on drawing schedules : ASNA2531-3 , Nut Example of part number construction : ASNA2531 Standard No. 3 Diameter code No. (see table 1) Material and finish code (see table 2)
6 -
MARKING Parts shall be marked as per EN2424, style F. As alternatives to the figure, marking can be tolerated on the hexagon (locking mark) or on the flanged area.
7 -
8 -
ASNA2531
Issue : Page : Sep 06 6
AMENDMENT RECORD SHEET Issue A.05.88 B.10.88 Modified paragraph Modification summary New standard. Chamfer added in figure. Values of dimensions W and T modified in table 1. C.04.89 Dimensions C and H modified in table 1. In figure : knurling for identification of diameter code No. 10 added. D.10.90 In table 1 : mass in kg/100 changed to mass in kg/1 000. E.04.91 In table, values of mass modified. Note 216.338/90 of A.DP.SM.MA F.01.99 Standard amended. In table 1, thread modified for code No. 4 : 0.2599-28 changed to 0.2500-28. code No. 12 added. G.01.00 Knurled flange of diameter code No. 10 deleted in figure. Dimension W modified in table 1 for diameter code No. 10 : 19,05/18,67 mm changed to 20,86/20,48 mm. H.02.02 Standard fully amended. Diameter code Nos 14 and 16 added. J.09.02 K.09.06 Diameter code Nos 2 and 3A added. Titanium material added. Chapter 2 updated. Go thread gage penetration in the deformation area. deleted in 4.3. Surface conditions and operating temperatures added in 4.3. Optional form added in the figure. Min. requirement for radius or chamfer height. Tolerance for H changed. NOTE : Modification to the last standard issue are indicated by a vertical line in the margin.
AIRBUS FRANCE 1988. All rights reserved
Justification
Following mistake
Following mistake
A 380
ASNA2531
Issue : Page : Sep 06 7
AMENDMENT RECORD SHEET Issue Modified paragraph Modification summary W dimensions applicable before locking deformation. Dimensions D, S and U added. Marking location alternatives. 4340 steel alloy material alternative added. ASNA2845 changed to ABS1420. Justification
NOTE : Modification to the last standard issue are indicated by a vertical line in the margin.
AIRBUS FRANCE 1988. All rights reserved