Users Manual Sysdrive 3G3JV PDF
Users Manual Sysdrive 3G3JV PDF
I528-E1-05
SYSDRIVE 3G3JV
USERS MANUAL
Thank you for choosing this SYSDRIVE 3G3JV-series product. Proper use and handling of the product will ensure proper product performance, will lengthen product life, and may prevent possible accidents. Please read this manual thoroughly and handle and operate the product with care.
1. To ensure safe and proper use of the OMRON Inverters, please read this USERS MANUAL (Cat. No. I528-E1) to gain sufficient knowledge of the devices, safety information, and precautions before actual use. 2. The products are illustrated without covers and shieldings for closer look in this USERS MANUAL. For actual use of the products, make sure to use the covers and shieldings as specified. 3. This USERS MANUAL and other related users manuals are to be delivered to the actual end users of the products. 4. Please keep this manual close at hand for future reference. 5. If the product has been left unused for a long time, please inquire at our sales representative.
NOTICE
1. This manual describes the functions of the product and relations with other products. You should assume that anything not described in this manual is not possible.
2. Although care has been given in documenting the product, please contact your OMRON representative if you have any suggestions on improving this manual. 3. The product contains potentially dangerous parts under the cover. Do not attempt to open the cover under any circumstances. Doing so may result in injury or death and may damage the product. Never attempt to repair or disassemble the product. 4. We recommend that you add the following precautions to any instruction manuals you prepare for the system into which the product is being installed. S Precautions on the dangers of high-voltage equipment. S Precautions on touching the terminals of the product even after power has been turned OFF. (These terminals are live even with the power turned OFF.) 5. Specifications and functions may be changed without notice in order to improve product performance.
USERS MANUAL
SYSDRIVE 3G3JV
SERIES
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property.
!
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Additionally, there may be severe property damage. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Additionally, there may be severe property damage. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or property damage.
WARNING
! Caution
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of information. Note Indicates information of particular interest for efficient and convenient operation of the product.
OMRON, 1999
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of OMRON. No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in this publication.
General Precautions
Observe the following precautions when using the SYSDRIVE Inverters and peripheral devices. This manual may include illustrations of the product with protective covers removed in order to describe the components of the product in detail. Make sure that these protective covers are on the product before use. Consult your OMRON representative when using the product after a long period of storage.
! !
WARNING WARNING
Do not touch the inside of the Inverter. Doing so may result in electrical shock. Operation, maintenance, or inspection must be performed after turning OFF the power supply, confirming that the CHARGE indicator (or status indicators) are OFF, and after waiting for the time specified on the front cover. Not doing so may result in electrical shock. Do not damage, pull on, apply stress to, place heavy objects on, or pinch the cables. Doing so may result in electrical shock. Do not touch the rotating parts of the motor under operation. Doing so may result in injury. Do not modify the product. Doing so may result in injury or damage to the product. Do not store, install, or operate the product in the following places. Doing so may result in electrical shock, fire or damage to the product. S Locations subject to direct sunlight. S Locations subject to temperatures or humidity outside the range specified in the specifications. S Locations subject to condensation as the result of severe changes in temperature. S Locations subject to corrosive or flammable gases. S Locations subject to exposure to combustibles. S Locations subject to dust (especially iron dust) or salts. S Locations subject to exposure to water, oil, or chemicals. S Locations subject to shock or vibration.
! Caution
! Caution
Do not touch the Inverter radiator, regenerative resistor, or Servomotor while the power is being supplied or soon after the power is turned OFF. Doing so may result in a skin burn due to the hot surface. Do not conduct a dielectric strength test on any part of the Inverter. Doing so may result in damage to the product or malfunction. Take appropriate and sufficient countermeasures when installing systems in the following locations. Not doing so may result in equipment damage. S Locations subject to static electricity or other forms of noise. S Locations subject to strong electromagnetic fields and magnetic fields. S Locations subject to possible exposure to radioactivity. S Locations close to power supplies.
! Caution
! Caution
Transportation Precautions
! Caution
Do not hold by front cover or panel, instead, hold by the radiation fin (heat sink) while transporting the product. Doing so may result in injury. Do not pull on the cables. Doing so may result in damage to the product or malfunction. Use the eye-bolts only for transporting the Inverter. Using them for transporting the machinery may result in injury or malfunction.
! Caution
! Caution
Installation Precautions
!
WARNING
Provide an appropriate stopping device on the machine side to secure safety. (A holding brake is not a stopping device for securing safety.) Not doing so may result in injury. Provide an external emergency stopping device that allows an instantaneous stop of operation and power interruption. Not doing so may result in injury. Be sure to install the product in the correct direction and provide specified clearances between the Inverter and control panel or with other devices. Not doing so may result in fire or malfunction. Do not allow foreign objects to enter inside the product. Doing so may result in fire or malfunction. Do not apply any strong impact. Doing so may result in damage to the product or malfunction.
WARNING
! Caution
! Caution
! Caution
Wiring Precautions
!
WARNING
Wiring must be performed only after confirming that the power supply has been turned OFF. Not doing so may result in electrical shock. Wiring must be performed by authorized personnel. Not doing so may result in electrical shock or fire. Be sure to confirm operation only after wiring the emergency stop circuit. Not doing so may result in injury. Always connect the ground terminals to a ground of 100 or less for the 200-V AC class, or 10 or less for the 400-V AC class. Not connecting to a proper ground may result in electrical shock.
WARNING
WARNING
WARNING
! Caution
Install external breakers and take other safety measures against short-circuiting in external wiring. Not doing so may result in fire. Confirm that the rated input voltage of the Inverter is the same as the AC power supply voltage. An incorrect power supply may result in fire, injury, or malfunction. Connect the Braking Resistor and Braking Resistor Unit as specified in the manual. Not doing so may result in fire. Be sure to wire correctly and securely. Not doing so may result in injury or damage to the product. Be sure to firmly tighten the screws on the terminal block. Not doing so may result in fire, injury, or damage to the product. Do not connect an AC power to the U, V, or W output. Doing so may result in damage to the product or malfunction.
! Caution
! Caution
! Caution
! Caution
! Caution
WARNING
Turn ON the input power supply only after mounting the front cover, terminal covers, bottom cover, Operator, and optional items. Not doing so may result in electrical shock. Do not remove the front cover, terminal covers, bottom cover, Operator, or optional items while the power is being supplied. Doing so may result in electrical shock or damage to the product. Do not operate the Operator or switches with wet hands. Doing so may result in electrical shock. Do not touch the inside of the Inverter. Doing so may result in electrical shock. Do not come close to the machine when using the error retry function because the machine may abruptly start when stopped by an alarm. Doing so may result in injury. Do not come close to the machine immediately after resetting momentary power interruption to avoid an unexpected restart (if operation is set to be continued in the processing selection function after momentary power interruption is reset). Doing so may result in injury. Provide a separate emergency stop switch because the STOP Key on the Operator is valid only when function settings are performed. Not doing so may result in injury.
WARNING
WARNING
WARNING WARNING
WARNING
WARNING
WARNING
Be sure to confirm that the RUN signal is turned OFF before turning ON the power supply, resetting the alarm, or switching the LOCAL/REMOTE selector. Doing so while the RUN signal is turned ON may result in injury.
! Caution
Be sure to confirm permissible ranges of motors and machines before operation because the Inverter speed can be easily changed from low to high. Not doing so may result in damage to the product.
! Caution
Provide a separate holding brake when necessary. Not doing so may result in injury.
! Caution
Do not perform a signal check during operation. Doing so may result in injury or damage to the product.
! Caution
Do not carelessly change settings. Doing so may result in injury or damage to the product.
WARNING
Do not touch the Inverter terminals while the power is being supplied.
WARNING
Maintenance or inspection must be performed only after turning OFF the power supply, confirming that the CHARGE indicator (or status indicators) is turned OFF, and after waiting for the time specified on the front cover. Not doing so may result in electrical shock.
WARNING
Maintenance, inspection, or parts replacement must be performed by authorized personnel. Not doing so may result in electrical shock or injury.
WARNING
Do not attempt to take the Unit apart or repair. Doing either of these may result in electrical shock or injury.
! Caution
Carefully handle the Inverter because it uses semiconductor elements. Careless handling may result in malfunction.
! Caution
Do not change wiring, disconnect connectors, the Operator, or optional items, or replace fans while power is being supplied. Doing so may result in injury, damage to the product, or malfunction.
Warning Labels
Warning labels are pasted on the product as shown in the following illustration. Be sure to follow the instructions given there.
H Warning Labels
Warning label
H Contents of Warning
S For 3G3JV-A2001 to A2007 (0.1 to 0.75 kW) and 3G3JV-AB001 to AB004 (0.1 to 0.4 kW):
S For 3G3JV-A2015 to A2037 (1.5 to 3.7 kW), 3G3JV-AB007 to AB015 (0.75 to 1.5 kW), and 3G3JV-A4002 to A4037 (0.2 to 3.7 kW):
Maximum applicable motor capacity Voltage class Installation type Series name: 3G3JV Series
Note The figures in parentheses indicate capacities for motors used outside Japan.
Voltage Class
2 B 4 Three-phase 200-V AC input (200-V class) Single-phase 200-V AC input (200-V class) Three-phase 400-V AC input (400-V class)
Installation Type
A Panel-mounting models (IP10 min.) or Closed wall mounting
Chapter
Chapter 1 Overview Chapter 2 Design Chapter 3 Preparing for Operation and Monitoring Chapter 4 Test Run
Contents
Describes features and nomenclature. Provides dimensions, installation methods, wiring methods, peripheral device design information, and peripheral device selection information. Describes nomenclature and Digital Operator procedures for operating and monitoring Inverters. Describes the method for controlling a motor through the frequency adjuster on the front of the Inverter. This can be used for trial operation of the system. Describes basic Inverter control functions for users not familiar with Inverters. The functions that must be understood to drive a motor with an Inverter are described. Describes all of the functions provided by the Inverter. These functions will enable more advanced applications, and includes functions that will improve motor control through the Inverter, such as responsiveness (torque characteristics), increasing speed accuracy, PID control, overtorque detection, and other functions. Describes the RS-422/485 Communications Unit and the general-purpose RS-422/485 communications functions provided by the Inverter, including connection methods and sample programming for SYSMAC Programmable Controllers. Provides maintenance, inspection, and troubleshooting information. Provides Inverter specifications, as well as the specifications and dimensions of peripheral devices. Lists basic information on Inverter parameters as a reference for users already familiar with Inverter operation. Parameters are listed in order with the page numbers of further information for easy reference. Describes information on using the Inverter for a motor.
Chapter 7 Communications
Application Considerations
CHANGE IN SPECIFICATIONS DIMENSIONS AND WEIGHTS PERFORMANCE DATA ERRORS AND OMISSIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. Performance data given in this manual is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRONs test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. The information in this manual has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.
Disclaimers
Table of Contents
Chapter 1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-1 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1-4
5-10
Table of Contents
Chapter 6. Advanced Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6-1 6-2 6-3 6-4 6-5 6-6 6-7 Setting the Carrier Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Injection Braking Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stall Prevention Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overtorque Detection Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Torque Compensation Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slip Compensation Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-1 Motor Protection Characteristics (n33 and n34) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-2 Cooling Fan Operation Function (n35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-3 Momentary Power Interruption Compensation (n47) . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-4 Fault Retry (n48) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-5 Frequency Jump Function (n49 to n51) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-6 Frequency Detection Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-7 UP/DOWN Command Frequency Memory (n62) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7-8 Error History (n78) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 6-5 6-6 6-9 6-11 6-12 6-14 6-14 6-14 6-15 6-15 6-16 6-17 6-19 6-21
Table of Contents
Chapter 8. Maintenance Operations . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8-1 Protective and Diagnostic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8-1-1 Fault Detection (Fatal Error) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8-1-2 Warning Detection (Nonfatal Error) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 8-2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 8-2-1 Parameters Fail Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 8-2-2 Motor Fails to Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 8-2-3 Motor Rotates in the Wrong Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 8-2-4 Motor Outputs No Torque or Acceleration is Slow . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 8-2-5 Motor Deceleration is Slow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 8-2-6 Motor Burns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 8-2-7 Controller or AM Radio Receives Noise when Inverter is Started . . . . . . . . . . . . . . . 8-13 8-2-8 Ground Fault Interrupter is Actuated when Inverter is Started . . . . . . . . . . . . . . . . . . 8-13 8-2-9 Mechanical Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 8-2-10 Motor Rotates after Output of Inverter is Turned Off . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 8-2-11 Detects OV when Motor Starts and Motor Stalls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 8-2-12 Output Frequency Does Not Reach Frequency Reference . . . . . . . . . . . . . . . . . . . . . . 8-15 8-2-13 Inverter Does Not Run Because EF (Simultaneous Input of Forward and Reverse Commands) is Detected, or Motor Rotates Momentarily While Control Device Power is OFF . . . 8-15 8-3 Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
Chapter 10. List of Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Chapter 11. Using the Inverter for a Motor . . . . . . . . . . . . . . . . . . . . . 11-1
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R-1
1
Chapter 1 Overview
1-1 1-2 Function Nomenclature
Chapter 1
The compact simple SYSDRIVE 3G3JV-Series Inverter ensures greater ease of use than any conventional model. The 3G3JV Inverter meets EC Directives and UL/cUL standard requirements for worldwide use.
Single-phase g p 200 V AC
3-phase p 400 V AC
Note 1. The figures in parentheses indicate typical motor capacities in Japan. Note 2. It is not possible to connect a Braking Resistor or Braking Unit to a 3G3JV-series Inverter. Select an Inverter from another series if the application requires braking control.
1-2
Overview
H Versatile Easy-to-use Functions
Chapter 1
Incorporates the functions and operability ensured by the conventional 3G3EV Series. Easy to initialize and operate with the FREQ adjuster on the Digital Operator. Ease of maintenance. The cooling fan is easily replaceable. The life of the cooling fan can be prolonged by turning on the cooling fan only when the Inverter is in operation.
H Suppression of Harmonics
Connects to DC reactors, thus suppressing harmonics more effectively than conventional AC reactors. Further improvement in the suppression of harmonics is possible with the combined use of the DC and AC reactors.
1-3
Chapter 1
H Panel
Top protection cover
Terminal block
Digital Operator
Optional cover
Front cover Terminal block U-shaped cutouts (Two) Front cover mounting screw
Note 1. The front cover functions as a terminal cover. The Digital Operator Unit cannot be removed. Note 2. Instead of mounting holes, each of the following models has two U-shaped cutouts located diagonally. 3G3JV-A2001 (0.1 kW), 3G3JV-A2002 (0.25 kW), 3G3JV-A2004 (0.55 kW), and 3G3JV-A2007 (1.1 kW) 3G3JV-AB001 (0.1 kW), 3G3JV-AB002 (0.25 kW), and 3G3JV-AB004 (0.55 kW)
1-4
Overview
H Digital Operator
Chapter 1
Data display
Keys
FREQ adjuster
Appearance
Function Displays relevant data items, such as frequency reference, output frequency, and parameter set values. Sets the frequency reference within a range between 0 Hz and the maximum frequency.
FREQ adjuster
FREF indicator FOUT indicator IOUT indicator MNTR indicator F/R indicator
LO/RE indicator
The frequency reference can be monitored or set while this indicator is lit. The output frequency of the Inverter can be monitored while this indicator is lit. The output current of the Inverter can be monitored while this indicator is lit. The values set in U01 through U10 are monitored while this indicator is lit. The direction of rotation can be selected while this indicator is lit when operating the Inverter with the RUN Key. The operation of the Inverter through the Digital Operator or according to the set parameters is selectable while this indicator is lit. Note This status of this indicator can be only monitored while the Inverter is in operation. Any RUN command input is ignored while this indicator is lit. The parameters in n01 through n79 can be set or monitored while this indicator is lit. Note While the Inverter is in operation, the parameters can be only monitored and only some parameters can be changed. Any RUN command input is ignored while this indicator is lit. Switches the setting and monitor item indicators in sequence. Parameter being set will be canceled if this key is pressed before entering the setting. Increases multi-function monitor numbers, parameter numbers, and parameter set values. Decreases multi-function monitor numbers, parameter numbers, and parameter set values.
PRGM indicator
Mode Key
1-5
Overview
Appearance Name Enter Key
Chapter 1
Function Enters multi-function monitor numbers, parameter numbers, and internal data values after they are set or changed. Starts the Inverter running when the 3G3JV is in operation with the Digital Operator. Stops the Inverter unless parameter n06 is set to disable the STOP Key. Functions as a Reset Key when an Inverter error occurs. (See note.)
Note For safety reasons, the reset will not work while a RUN command (forward or reverse) is in effect. Wait until the RUN command is OFF before resetting the Inverter.
1-6
2
Chapter 2 Design
2-1 2-2 Installation Wiring
Chapter 2
2-1-1 Dimensions
D 3G3JV-A2001 to 3G3JV-A2007 (0.1 to 0.75 kW) 3-phase 200-V AC Input 3G3JV-AB001 to 3G3JV-AB004 (0.1 to 0.4 kW) Single-phase 200-V AC Input
t
D1
Model 3G3JVD A2001 A2002 A2004 A2007 AB001 AB002 AB004 70 70 102 122 70 70 112
Dimensions (mm) D1 10 10 42 62 10 10 42 3 3 5 5 3 3 5 t
Weight g ( (kg) g) Approx. 0.5 Approx. 0.5 Approx. 0.8 Approx. 0.9 Approx. 0.5 Approx. 0.5 Approx. 0.9
Single-phase g p 200 V AC
2-2
Design
Chapter 2
D 3G3JV-A2015 to 3G3JV-A2022 (1.5 to 2.2 kW) 3-phase 200-V AC Input 3G3JV-AB007 to 3G3JV-AB015 (0.75 to 1.5 kW) Single-phase 200-V AC Input 3G3JV-A4002 to 3G3JV-A4022 (0.2 to 2.2 kW) 3-phase 400-V AC Input
Two, 5-dia. holes
D1 D
Model 3G3JVA2015 A2022 AB007 AB015 A4002 A4004 A4007 A4015 A4022 129 154 129 154 81 99 129 154 154
Dimensions (mm) D 64 64 64 64 16 34 64 64 64 D1
Weight g ( (kg) g) Approx. 1.3 Approx. 1.5 Approx. 1.5 Approx. 1.5 Approx. 1.0 Approx. 1.1 Approx. 1.5 Approx. 1.5 Approx. 1.5
2-3
Design
D 3G3JV-A2037 (3.7 kW) 3-phase 200-V AC Input 3G3JV-A4037 (3.7 kW) 3-phase 400-V AC Input
Two, 5-dia. holes
Chapter 2
128
118
D1
WARNING
Provide an appropriate stopping device on the machine side to secure safety. (A holding brake is not a stopping device for securing safety.) Not doing so may result in injury. Provide an external emergency stopping device that allows an instantaneous stop of operation and power interruption. Not doing so may result in injury. Be sure to install the product in the correct direction and provide specified clearances between the Inverter and control panel or with other devices. Not doing so may result in fire or malfunction. Do not allow foreign objects to enter inside the product. Doing so may result in fire or malfunction. Do not apply any strong impact. Doing so may result in damage to the product or malfunction.
WARNING
! Caution
! Caution
! Caution
2-4
Design
H Installation Direction and Dimensions
Install the Inverter under the following conditions. Ambient temperature for operation (panel-mounting): 10C to 50C Humidity: 95% or less (no condensation)
Chapter 2
Install the Inverter in a clean location free from oil mist and dust. Alternatively, install it in a totally enclosed panel that is completely protected from floating dust. When installing or operating the Inverter, always take special care so that metal powder, oil, water, or other foreign matter does not get into the Inverter. Do not install the Inverter on inflammable material such as wood.
H Direction
Install the Inverter on a vertical surface so that the characters on the nameplate are oriented upward.
H Dimensions
When installing the Inverter, always provide the following clearances to allow normal heat dissipation from the Inverter.
W = 30 mm min.
100 mm min.
Air
Inverter
Inverter
Inverter
Side
100 mm min.
Air
2-5
Design
H Protecting Inverter from Foreign Matter during Installation
Chapter 2
Place a cover over the Inverter during installation to shield it from metal power produced by drilling. Upon completion of installation, always remove the cover from the Inverter. Otherwise, ventilation will be affected, causing the Inverter to overheat.
2-6
Design 2-2
!
Chapter 2
Wiring
Wiring must be performed only after confirming that the power supply has been turned OFF. Not doing so may result in electrical shock. Wiring must be performed by authorized personnel. Not doing so may result in electrical shock or fire. Be sure to confirm operation only after wiring the emergency stop circuit. Not doing so may result in injury. Always connect the ground terminals to a ground of 100 or less for the 200-V AC class, or 10 or less for the 400-V AC class. Not connecting to a proper ground may result in electrical shock. Install external breakers and take other safety measures against short-circuiting in external wiring. Not doing so may result in fire. Confirm that the rated input voltage of the Inverter is the same as the AC power supply voltage. An incorrect power supply may result in fire, injury, or malfunction. Connect the Braking Resistor and Braking Resistor Unit as specified in the manual. Not doing so may result in fire. Be sure to wire correctly and securely. Not doing so may result in injury or damage to the product. Be sure to firmly tighten the screws on the terminal block. Not doing so may result in fire, injury, or damage to the product. Do not connect an AC power to the U, V, or W output. Doing so may result in damage to the product or malfunction.
WARNING
WARNING
WARNING
WARNING
! Caution
! Caution
! Caution
! Caution
! Caution
! Caution
2-7
Chapter 2
It is necessary to remove the front cover, optional cover, top protection cover, and the bottom protection cover from the Inverter to wire the terminal block. Follow the instructions below to remove the covers from the Inverter. To mount the covers, take the opposite steps.
Loosen the front cover mounting screws with a screwdriver. Press the left and right sides of the front cover in the arrow 1 directions and lift the bottom of the cover in the arrow 2 direction to remove the front cover as shown in the following illustration.
H Removing the Top and Bottom Protection Covers and Optional Cover
D Removing the Top and Bottom Protection Covers
After removing the front cover, pull the top and bottom protection covers in the arrow 1 directions.
2-8
Design
D Removing the Optional Cover
Chapter 2
After removing the front cover, lift the optional cover in the arrow 2 direction based on position A as a fulcrum.
Position A
Note The front cover functions as a terminal cover. The Digital Operator cannot be removed.
2-9
Design
H Arrangement of Control Circuit Terminals
Chapter 2
2-10
Design
H Main Circuit Terminals
Symbol R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 +1 +2 Connection terminals +1 and +2: DC reactor connection terminals +1 and : DC power supply input terminals Ground terminal Motor output terminals Name Power supply input terminals Description 3G3JV-A2j: 3-phase 200 to 230 V AC 3G3JV ABj: Si l h 200 t 3G3JV-AB Single-phase to 240 V AC 3G3JV-A4j: 3-phase 380 to 460 V AC
Chapter 2
Note Connect single-phase input to terminals R/L1 and S/L2. 3-phase power supply output for driving motors. 3G3JV-A2j: 3-phase 200 to 230 V AC 3G3JV-ABj: 3-phase 200 to 240 V AC 3G3JV-A4j: 3-phase 380 to 460 V AC Connect the DC reactor for suppressing harmonics to terminals +1 and +2. When driving the Inverter with DC power, input the DC power to terminals +1 and . (Terminal +1 is a positive terminal terminal.) )
Be sure to ground the terminal under the following conditions. 3G3JV-A2j: Ground at a resistance of 100 or less. 3G3JV-ABj: Ground at a resistance of 100 or less. 3G3JV-A4j: Ground at a resistance of 10 or less, and connect to the power supplys neutral phase to conform to EC Directives. Note Be sure to connect the ground terminal directly to the motor frame ground.
Note The maximum output voltage corresponds to the power supply input voltage of the Inverter.
S5 SC FS FR FC
2-11
Design
Symbol Output MA MB MC AM AC Name Multi-function contact output (Normally open) Multi-function contact output (Normally closed) Multi-function contact output common Analog monitor output Analog monitor output common Function Set by parameter n40 (during ( g running) g)
Chapter 2
Signal level Relay output 1 A max. at 30 V DC C 1 A max. at 250 V AC
Common for MA and MB use Set by parameter n44 (Output frequency) Common for AM use
2 mA max. at 0 to 10 V DC
Note 1. Depending on the parameter settings, various functions can be selected for multi-function inputs and multi-function contacts outputs. Note 2. Functions in parentheses are default settings.
Switches SW7 and SW8, both of which are located above the control circuit terminals, are used for input method selection. Remove the front cover and optional cover to use these switches.
2-12
Design
D Selecting Sequence Input Method
By using SW7, NPN or PNP input can be selected as shown below.
Chapter 2
S1 to 5
S1 to 5 24 V DC (10%)
By using SW8, frequency reference voltage or current input can be selected. Parameter settings are required together with the selection of the frequency reference input method.
Frequency reference input method Voltage input Current input SW8 setting V (OFF) I (ON) Frequency reference selection (parameter n03) Set value 2 Set value 3 or 4
2-13
Chapter 2
Sequence input common Frequency reference power supply 20 mA at +12 V Frequency reference input
Frequency reference common
FREQ adjuster
(2 k, 1/4 W min.)
Note 1. Connect single-phase 200 V AC to terminals R/L1 and S/L2 of the 3G3JV-ABj. Note 2. The braking resistor cannot be connected because no braking transistor is incorporated.
2-14
Chapter 2
H Wire Size, Terminal Screw, Screw Tightening Torque, and Molded-case Circuit Breaker Capacities
For the main circuit and ground, always use 600-V polyvinyl chloride (PVC) cables. If any cable is long and may cause voltage drops, increase the wire size according to the cable length.
A2001
R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3
M3.5
0.8 to 1.0
0.75 to 2
A2002
M3.5
0.8 to 1.0
0.75 to 2
A2004
M3.5
0.8 to 1.0
0.75 to 2
A2007
M3.5
0.8 to 1.0
0.75 to 2
10
A2015
M3.5
0.8 to 1.0
2 to 5.5
20
A2022
M3.5
0.8 to 1.0
2 to 5.5
3.5
20
A2037
M4
1.2 to 1.5
2 to 5.5
5.5
30
2-15
Design
D Single-phase 200-V AC Model
Model 3G3JVTerminal symbol Terminal screw Terminal torque (NSm) 0.8 to 1.0 Wire size (mm2)
Chapter 2
Recomme Circuit nded wire breaker size capacity (mm2) (A) 2 5
AB001
R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3
M3.5
0.75 to 2
AB002
M3.5
0.8 to 1.0
0.75 to 2
AB004
M3.5
0.8 to 1.0
0.75 to 2
10
AB007
M3.5
0.8 to 1.0
2 to 5.5
3.5 2
20
AB015
M3.5
0.8 to 1.0
2 to 5.5
5.5 2
20
A4002
R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, , +1, +2, U/T1, V/T2, W/T3
M3.5
2 to 5.5
A4004
M3.5
0.8 to 1.0
2 to 5.5
A4007
M3.5
0.8 to 1.0
2 to 5.5
A4015
M3.5
0.8 to 1.0
2 to 5.5
10
A4022
M4
1.2 to 1.5
2 to 5.5
10
A4037
M4
1.2 to 1.5
2 to 5.5
2 3.5
20
2-16
Design
H Wiring on the Input Side of the Main Circuit
D Installing a Molded-case Circuit Breaker
Chapter 2
Always connect the power input terminals (R/L1, S/L2, and T/L3) and power supply via a molded case circuit breaker (MCCB) suitable to the Inverter. Install one MCCB for every Inverter used. Choose an appropriate MCCB capacity according to the Circuit breaker capacity column in the table on the previous page. For the MCCBs time characteristics, be sure to consider the Inverters overload protection (one minute at 150% of the rated output current). If the MCCB is to be used in common among multiple Inverters, or other devices, set up a sequence such that the power supply will be turned off by a fault output, as shown in the following diagram.
Inverter Power supply 3-phase/Single-phase 200 V AC 3-phase 400 V AC
2-17
Design
Chapter 2
A load can be started and stopped by opening and closing the magnetic contactor on the primary side. Frequently opening and closing the magnetic contactor, however, may cause the Inverter to break down. In order not to shorten the service life of the Inverters internal relays and electrolytic capacitors, it is recommended that the magnetic contactor is used in this way no more than once every 30 minutes. When the Inverter is operated with the Digital Operator, automatic operation cannot be performed after recovery from a power interruption.
D Installing an AC Reactor
If the Inverter is connected to a large-capacity power transformer (660 kW or more) or the phase advance capacitor is switched, an excessive peak current may flow through the input power circuit, causing the converter unit to break down. To prevent this, install an optional AC reactor on the input side of the Inverter. This also improves the power factor on the power supply side.
Wiring Example 1
Input Noise Filters Simple Input Noise Filter: 3G3EV-PLNFDj EMC-conforming Input Noise Filter: 3G3JV-PRSj
Power supply
Programmable Controller
Note Use a Noise Filter designed for the Inverter. A general-purpose Noise Filter will be less effective and may not reduce noise.
2-18
Design
H Wiring on the Output Side of the Main Circuit
D Connecting the Terminal Block to the Load
Connect output terminals U/T1, V/T2, and W/T3 to motor lead wires U, V, and W.
Chapter 2
Check that the motor rotates forward with the forward command. Switch over any two of the output terminals to each other and reconnect if the motor rotates in reverse with the forward command.
Signal line
2-19
Design
Induction Noise: Radio Noise:
Chapter 2
Electromagnetic induction generates noise on the signal line, causing the controller to malfunction. Electromagnetic waves from the Inverter and cables cause the broadcasting radio receiver to make noise.
Power supply
2-20
Design
Chapter 2
Also, adjust the carrier frequency (set in n46) according to the cable length between the Inverter and the motor, as shown in the following table.
Cable length Carrier frequency 50 m or less 10 kHz max. 100 m or less 5 kHz max. More than 100 m 2.5 kHz
Note Single-phase motors cannot be used. The Inverter is not suited for the variable speed control of single-phase motors. The rotation direction of a single-phase motor is determined by the capacitor starting method or phase-splitting starting method to be applied when starting the motor. In the capacitor starting method, however, the capacitor may be damaged by a sudden electric discharge of the capacitor caused by the output of the Inverter. On the other hand, the starting coil may burn in the phase-splitting starting method because the centrifugal switch does not operate.
H Ground Wiring
Always use the ground terminal with the following ground resistance: 200-V Inverter: 100 or less 400-V Inverter: separate ground,10 or less Do not share the ground wire with other devices such as welding machines or power tools. Always use a ground wire that complies with technical standards on electrical equipment and minimize the length of the ground wire. Leakage current flows through the Inverter. Therefore, if the distance between the ground electrode and the ground terminal is too long, the potential on the ground terminal of the Inverter will become unstable.
2-21
Design
When using more than one Inverter, be careful not to loop the ground wire.
Chapter 2
D Harmonics Definition
Harmonics consist of electric power produced from AC power and alternating at frequencies that are integral multiples of the frequency of the AC power.
2-22
Design
Chapter 2
The following frequencies are harmonics of a 60- or 50-Hz commercial power supply. Second harmonic: 120 (100) Hz Third harmonic: 180 (150) Hz
Second harmonic (120 Hz) Basic frequency (60 Hz)
Usually, electric machines have built-in circuitry that converts commercial AC power supply into DC power. Such AC power, however, contains harmonics due to the difference in current flow between DC and AC.
2-23
Design
Inverter
Chapter 2
The Inverter as well as normal electric machines has an input current containing harmonics because the Inverter converts AC into DC. The output current of the Inverter is comparatively high. Therefore, the ratio of harmonics in the output current of the Inverter is higher than that of any other electric machine.
Voltage
Time
Rectified Voltage
Time Current A current flows into the capacitors. The current is different from the voltage in waveform.
Time
2-24
Design
D Countermeasures with Reactors against Harmonics Generation DC/AC Reactors
Chapter 2
The DC reactor and AC reactor suppress harmonics and currents that change suddenly and greatly. The DC reactor suppresses harmonics better than the AC reactor. The DC reactor used with the AC reactor suppresses harmonics more effectively. The input power factor of the Inverter is improved by suppressing the harmonics of the input current of the Inverter.
Connection
Connect the DC reactor to the internal DC power supply of the Inverter after shutting off the power supply to the Inverter and making sure that the charge indicator of the Inverter turns off. Do not touch the internal circuitry of the Inverter in operation, otherwise an electric shock or burn injury may occur.
Wiring Method
With DC Reactor
DC reactor (optional)
Power supply
SYSDRIVE 3G3JV
Power supply
AC reactor (optional)
SYSDRIVE 3G3JV
2-25
Design
Reactor Effects
Chapter 2
Harmonics are effectively suppressed when the DC reactor is used with the AC reactor as shown in the following table.
Harmonics suppression i method No reactor AC reactor DC reactor DC and AC reactors Harmonic generation rate (%) 5th harmonic 65 38 30 28 7th harmonic 41 14.5 13 9.1 11th harmonic 8.5 7.4 8.4 7.2 13th harmonic 7.7 3.4 5 4.1 17th harmonic 4.3 3.2 4.7 3.2 19th harmonic 3.1 1.9 3.2 2.4 23rd harmonic 2.6 1.7 3.0 1.6 25th harmonic 1.8 1.3 2.2 1.4
D Wires and Tightening Torque Multi-function Contact Output (MA, MB, and MC)
Terminal screw size M3 Tightening torque NSm 0.5 to 0.6 Wire Single wire Stranded wire Wire size 0.5 to 1.25 (20 to 16) 0.5 to 1.25 (20 to 16) Recommend Cable ed wire size 0.75 (18) Cable with polyethylene sheath
Sequential Input (S1 through S5 and SC) and Analog Monitor Output (AM or AC)
Terminal screw size M2 Tightening torque NSm 0.22 to 0.25 Wire Single wire Stranded wire Wire size 0.5 to 1.25 (20 to 16) 0.5 to 0.75 (20 to 18) Recommend Cable ed wire size 0.75 (18) Cable with polyethylene sheath
2-26
Design
D Solderless Terminal Size
Chapter 2
The use of solderless terminals for the control circuit terminals is recommended for the reliability and ease of connection. Note Make sure that the wire size is 0.5 mm2 when using the following solderless terminal.
1.0 dia.
(Size: mm)
2.6 dia.
D Wiring Method
1. Loosen the terminal screws with a thin-slotted screwdriver. 2. Insert the wires from underneath the terminal block. 3. Tighten each terminal screw firmly to a torque specified in the previous tables. Note 1. Always separate the control signal line from the main circuit cables and other power cables. Note 2. Do not solder the wires to the control circuit terminals. The wires may not contact well with the control circuit terminals if the wires are soldered. Note 3. The end of each wire connected to the control circuit terminals must be stripped for approximately 5.5 mm. Note 4. Connect the shield wire to the ground terminal of the 3G3JG. Do not connect the shield wire to the device side being controlled. Note 5. Be sure to insulate the shield wire with tape so that the shield wire will not come into contact with other signal wires or equipment.
Thin-slotted screwdriver Terminal block
Strip the end for approximately 5.5 mm if no solderless terminal is used. Wire
Note Applying excessive torque may damage the terminal block. If the tightening torque is insufficient, however, wires may disconnect.
2-27
Chapter 2
The following description provides the wiring method of the Inverter to meet DC Directive requirements. If the following requirements are not satisfied, the whole equipment incorporating the Inverter will need further confirmation.
H Standard Connection
D Main Circuit Terminals
MCCBs Noise Filter Clamp core
Forward/Stop
Multi-function input 1 (S2) Multi-function input 2 (S3) Multi-function input 3 (S4) Multi-function input 4 (S5)
NO NC Common
Analog-monitor output
Analog monitor output common
(2 k, 1/4 W min.)
2-28
Design
D Wiring the Power Supply
Make sure that the Inverter and Noise Filter are grounded together.
Chapter 2
Always connect the power input terminals (R/L1, S/L2, and T/L3) and power supply via a dedicated Noise Filter. Reduce the length of the ground wire as much as possible. Locate the Noise Filter as close as possible to the Inverter. Make sure that the cable length between the Noise Filter and the Inverter does not exceed 40 cm. The following Noise Filters are available.
2-29
Design
D Grounding the Shield
Chapter 2
In order to ground the shield securely, it is recommended that a cable clamp be directly connected to the ground plate as shown below.
Ground plate Cable clamp
Cable
Shield
H LVD Conformance
Always connect the Inverter and power supply via a molded case circuit breaker (MCCB) suitable to the Inverter for protecting the Inverter from damage that may result from short-circuiting. Use one MCCB per Inverter. Select a suitable MCCB from the following table. With 400-V Inverters, it is necessary to ground to the power supplys neutral phase.
200-V Models
Inverter Model 3G3JVA2001 A2002 A2004 A2007 A2015 A2022 A2037 AB001 AB002 AB004 AB007 AB015 NF30 MCCB (Mitsubishi Electric) Type Rated current (A) 5 5 5 10 20 20 30 5 5 10 20 20
NF30
2-30
Design
400-V Models
Inverter Model 3G3JVA4002 A4004 A4007 A4015 A4022 A4037 NF30 MCCB (Mitsubishi Electric) Type Rated current (A) 5 5 5 10 10 20
Chapter 2
To satisfy LVD (Low-voltage Directive) requirements, the system must be protected by a molded case circuit breaker (MCCB) when a short-circuit occurs. A single MCCB may be shared with more than one Inverter or with other machines. In that case, however, take some appropriate measures so that the MCCB will protect all the Inverters from the occurrence of any single short-circuit. The frequency reference power supply (FS) of the Inverter is of basic insulation construction. When connecting the Inverter to peripheral devices, be sure to increase the degree of insulation.
2-31
3
Chapter 3 Preparing for Operation and Monitoring
3-1 3-2 Nomenclature Parameter Copy and Verify Function
Chapter 3
Keys
FREQ adjuster
Appearance
Function Displays relevant data items, such as frequency reference, output frequency, and parameter set values. Sets the frequency reference within a range between 0 Hz and the maximum frequency.
FREQ adjuster
FREF indicator FOUT indicator IOUT indicator MNTR indicator F/R indicator
LO/RE indicator
The frequency reference can be monitored or set while this indicator is lit. The output frequency of the Inverter can be monitored while this indicator is lit. The output current of the Inverter can be monitored while this indicator is lit. The values set in U01 through U10 are monitored while this indicator is lit. The direction of rotation can be selected while this indicator is lit, when operating the Inverter with the RUN Key. The operation of the Inverter through the Digital Operator or according to the parameters set is selectable while this indicator is lit. Note This status of this indicator can be only monitored while the Inverter is in operation. Any RUN command input is ignored while this indicator is lit. The parameters in n01 through n79 can be set or monitored while this indicator is lit. Note While the Inverter is in operation, the parameters can be only monitored and only some parameters can be changed. The RUN command input is ignored while this indicator is lit. Switches the setting and monitor item indicators in sequence. Parameter setting being made is canceled if this key is pressed before entering the setting. Increases multi-function monitor numbers, parameter numbers, and parameter set values.
PRGM indicator
Mode Key
Increment Key
3-2
Chapter 3
Function Decreases multi-function monitor numbers, parameter numbers, and parameter set values. Enters multi-function monitor numbers, parameter numbers, and internal data values after they are set or changed. Starts the Inverter running when the 3G3FV is in operation with the Digital Operator. Stops the Inverter unless n06 is set to disable the STOP Key. Functions as a Reset Key when an Inverter error occurs. (See note.)
Note For safetys reasons, the reset will not work while a RUN command (forward or reverse) is in effect. Wait until the RUN command is OFF before resetting the Inverter.
D Setting Parameters
If the following setting is made, operation commands will always be received in Drive Mode even if the indicator is lit red.
3-3
Chapter 3
Note 2. As an exception, operation commands are not received when n01 itself is being changed. Note 3. Some parameters can be changed during operation and other parameters cannot. This is not affected by the setting of n01. If the setting for n01 has been changed to 5, operation commands will be received even while parameters are being changed, such as during testing. Sufficiently check safety before operation.
3-4
Chapter 3
Whenever the Mode Key is pressed, an indicator is lit in sequence beginning with the FREF indicator. The data display indicates the item corresponding to the indicator selected. The FOUT or IOUT indicator will be lit by turning the Inverter on again if the Inverter is turned off while the FOUT or IOUT indicator is lit. The FREF indicator will be lit by turning the Inverter on again if the Inverter is turned off while an indicator other than the FOUR or IOUT indicator is lit.
Power On FREF (Frequency Reference) Monitors and sets the frequency reference.
FOUT (Output Frequency) Monitors the output frequency. Note This indicator will be lit by turning the Inverter on again if the Inverter is turned off while this indicator is lit.
IOUT (Output Current) Monitors the output current. Note This indicator will be lit by turning the Inverter on again if the Inverter is turned off while this indicator is lit.
MNTR (Multi-function Monitor) Monitors the values set in U01 through U10.
LO/RE (Local/Remote) Selects the operation of the Inverter through the Digital Operator or according to the parameters.
PRGM (Parameter Setting) Monitors or sets the values in n01 through n79.
3-5
Chapter 3
Key sequence
Indicator
Display example
Explanation Power On Note If the FREF indicator has not been lit, press the Mode Key repeatedly until the FREF indicator is lit. Use the Increment or Decrement Key to set the frequency reference. The data display will flash while the frequency reference is set. (see note 1) Press the Enter Key so that the set value will be entered and the data display will be lit. (see note 1)
Note 1. The Enter Key need not be pressed when performing the setting for n08. The frequency reference will change when the set value is changed with the Increment or Decrement Key while the data display is continuously lit. Note 2. The frequency reference can be set in either of the following cases. S Parameter n03 for frequency reference selection is set to 1 (i.e., frequency reference 1 is enabled) and the Inverter is in remote mode. S Parameter n07 for frequency selection in local mode is set to 1 (i.e., the Digital Operator is enabled) and the Inverter is in local mode. S Frequency references 2 through 8 are input for multi-step speed operation. Note 3. The frequency reference can be changed, even during operation.
Key sequence
Indicator
Display Power On
Explanation
Press the Mode Key repeatedly until the MNTR indicator is lit. U01 will be displayed. Use the Increment or Decrement Key to select the monitor item to be displayed. Press the Enter Key so that the data of the selected monitor item will be displayed. The monitor number display will appear again by pressing the Mode Key.
3-6
Chapter 3
Monitors the frequency reference. (Same as FREF) Monitors the output frequency. (Same as FOUT) Monitors the output current. (Same as IOUT) Monitors the internal output voltage reference value of the Inverter. Monitors the DC voltage of the internal main circuit of the Inverter. Shows the ON/OFF status of inputs.
: Input ON : No input
Not used
Terminal S1: Forward/Stop Terminal S2: Multi-function input 1 (S2) Terminal S3: Multi-function input 2 (S3) Terminal S4: Multi-function input 3 (S4) Terminal S5: Multi-function input 4 (S5)
U07
---
U09
---
Error
U10
Software No.
---
Key sequence
Indicator
Display example
Explanation Press the Mode Key repeatedly until the F/R indicator is lit. The present setting will be displayed. For: Forward; rEv: Reverse Use the Increment or Decrement Key to change the direction of motor rotation. The direction of motor rotation selected will be enabled when the display changes after the key is pressed.
Note The direction of motor rotation can be changed, even during operation.
3-7
Chapter 3
Key sequence
Indicator
Display example
Explanation Press the Mode Key repeatedly until the LO/RE indicator is lit. The present setting will be displayed. rE: Remote; Lo: Local Use the Increment or Decrement Key to set the Inverter to local or remote mode. The selection will be enabled when the display changes after the key is pressed.
Note 1. Local or remote selection is possible only when the Inverter is not in operation. The present setting can be monitored when the Inverter is in operation. Note 2. Local or remote settings in multi-function input terminals can be changed through the multifunction input terminals only. Note 3. Any RUN command input will be ignored while the LO/RE indicator is lit. To enable a RUN command, first turn the RUN command OFF and then press the Mode Key to display an item that has a green indicator (FREF to MNTR). Then input the RUN command again.
In approximately 1 s.
Key sequence
Indicator
Explanation
In approximately 1 s.
Press the Mode Key repeatedly until the PRGM indicator is lit. Use the Increment or Decrement Key to set the parameter number. Press the Enter Key. The data of the selected parameter number will be displayed. Use the Increment or Decrement Key to set the data. At that time the display will flash. Press the Enter Key so that the set value will be entered and the data display will be lit. (see note 1) The parameter number will be displayed.
3-8
Chapter 3
Note 1. To cancel the set value, press the Mode Key instead. The parameter number will be displayed. Note 2. There are parameters that cannot be changed while the Inverter is in operation. Refer to the list of parameters. When attempting to change such parameters, the data display will not change by pressing the Increment or Decrement Key. Note 3. Any RUN command input will be ignored while the Parameter Setting (PRGM) indicator is lit. To enable a RUN command, first turn the RUN command OFF and then press the Mode Key to display an item that has a green indicator (FREF to MNTR). Then input the RUN command again.
3-9
Preparing for Operation and Monitoring 3-2 Parameter Copy and Verify Function
Chapter 3
The 3G3IV-PJVOP140 and 3G3IV-PJVOP146 Digital Operators include EEPROM memory. All the parameters for the Inverter, the Inverter capacity, and the software version are saved in this memory. If the memory is used, the parameter settings for the Inverter can be copied to other Inverters. Note: Copying can be performed between Inverters with the same power supply specifications. Some parameters, however, may not be copied.
Selects the function for copying parameters. Rdy: Ready to accept the next command. Red: Read the Inverter parameters. Cpy: Copy the parameters to the Inverter. VFy: Verify the Inverter parameters. Va: Verify the Inverter capacity display. Sno: Verify the software number.
3-10
Chapter 3
Reading
or
Writing
or
Verifying
or
Inverter capacity
or
Software No.
or
Note The following table shows the display for the Inverter capacity (vA).
3-11
Chapter 3
This parameter is used to prohibit writing to parameters to be written, to enable setting parameters, or to change the monitor range of parameters. 0: Enables setting or monitoring parameter n01. Parameters n02 to n79 can be monitored only. 1: Enables setting parameters n01 to n49. 5: Enables continuous operation. (Parameters n01 to n79 can be set or monitored.) 6: Clears the error log. 8: Initializes parameters to the default values for 2-wire sequence. 9: Initializes parameters to the default values for 3-wire sequence. Note With settings 0 or 1, operation commands are ignored in Program Mode. (Refer to 3-1-2 Drive Mode and Program Mode.) Normally, use a setting of 0 or 1.
3-12
Chapter 3
(After completion) or
3-13
Chapter 3
H Copying the Memory Contents of the Digital Operator to the Inverter (CPy)
The parameter settings saved in the memory of the Digital Operator can be written to the Inverter by setting the Parameter Copy and Verify Function (n76) to Cpy. When reading from the Digital Operator has been completed, turn OFF the Inverter power supply and remove the Digital Operator. Install the Digital Operator on the Inverter to which the parameters are to be written and turn ON the power supply. In the Parameter Write-prohibit Selection/Parameter Initialization (n01) is not set to 1 for that Inverter, use the same procedure as described above to set it to 1. Note Parameters can be copied only between Inverters with the same power supply specifications.
(After completion) or
Note 1. A setting range check and consistency check will be performed for the parameters after the memory contents of the Digital Operator have been written to the Inverter. If there is one or more parameters with an error, all parameters will be returned to their previous settings and none of them will be changed. If there is a setting range error, the number of the parameter that caused the error will flash. If there is a consistency error, oPj (j as a number) will flash. Note 2. The saved hold output frequency and the following parameters cannot be copied. n76: Parameter Copy and Verify Function n77: Parameter Read Prohibit Selection n78: Error Log n79: Software Number
3-14
Chapter 3
The parameter settings saved in the memory of the Digital Operator can be verified with the parameter settings in the Inverter by setting the Parameter Copy and Verify Function (n76) to vFy. Note Just as with copying, parameters can be verified only for Inverters that have the same power supply specifications.
(After completion) or
Note 1. Verification will be cancelled and the display will change to End if the STOP/RESET Key is pressed while the number of an inconsistent parameter is being displayed or the setting is being displayed. The display will then return to the number of the inconsistent parameter when the Mode Key or the Enter Key is pressed. Note 2. The display will flash vAE if you attempt to verify parameters between Inverters that have different capacities. To continue verifying anyway, press the Enter Key. To cancel verifying, press the STOP/RESET Key.
3-15
Chapter 3
Used to prohibit writing parameters. Use this parameter to protect the contents of the EEPROM memory in the Digital Operator. 0: Reading prohibited for Inverter parameters (Data cannot be written to EEPROM.) 1: Reading possible for Inverter parameters (Data can be written to EEPROM.)
Note 1. It is not possible to write to the n77 parameter with the default setting. To enable writing to n77, set the Parameter Write-prohibit Selection/Parameter Initialization (n01) to 1. Note 2. This parameter is set in the Digital Operator. The setting for n77 will be 0 (read prohibited) regardless of the Inverter setting if a Digital Operator that is set to prohibited reading is installed on another Inverter.
In approximately 1 s.
3-16
Chapter 3
3-2-4 Error Displays for the Parameter Copy and Verify Function
This section describes the errors that may occur when reading, copying, or verifying parameters, and the remedies for those errors. The display will flash when any of these errors occurs.
Display Probable cause Protect error Name A read attempt was made with the Parameter Read Prohibit Selection (n77) set to 0 (reading prohibited). The parameters were not read correctly or a low voltage was detected in the main circuit when the data was being read. A checksum error occurred for the parameters saved in the Digital Operator. There are no parameters saved in the Digital Operator. An attempt was made to copy or verify between Inverters with different voltage classes or control modes. Remedy Check again whether data must be read, and if required, change the setting for n77 to 1 (reading possible), and then read the data again. Check that the main circuit voltage is normal, and then read the data again.
Read error
Read the parameters to the Digital Operator again. Read the parameters to the Digital Operator. Check the voltage classes and control modes. (If either is different from that of the other Inverter, copying and verifying are not possible.) If an Inverter has a different control mode, change the control mode of the Inverter to be copied to or verified, and then copy or verify the parameters again. Check that the main voltage is normal, and then copy the data again. To continue verification, press the Enter Key. To cancel verification, press the STOP/RESET Key. Check the connection between the Inverter and the Digital Operator. Make sure the connection is correct, and then repeat the operation.
Voltage error A low voltage in the main circuit was while copying detected while data was being copied. Capacity error An attempt was made to verify parameters between Inverters with different capacities. CommunicaA communications error occurred tions error between the Inverter and the Digital Operator.
3-17
4
Chapter 4 Test Run
4-1 4-2 Procedure for Test Run Operation Example
Test Run
!
Chapter 4
Turn ON the input power supply only after mounting the front cover, terminal covers, bottom cover, Operator, and optional items. Not doing so may result in electrical shock. Do not remove the front cover, terminal covers, bottom cover, Operator, or optional items while the power is being supplied. Not doing so may result in electrical shock or damage to the product. Do not operate the Operator or switches with wet hands. Doing so may result in electrical shock. Do not touch the inside of the Inverter. Doing so may result in electrical shock. Do not come close to the machine when using the error retry function because the machine may abruptly start when stopped by an alarm. Doing so may result in injury. Do not come close to the machine immediately after resetting momentary power interruption to avoid an unexpected restart (if operation is set to be continued in the processing selection function after momentary power interruption is reset). Doing so may result in injury. Provide a separate emergency stop switch because the STOP Key on the Operator is valid only when function settings are performed. Not doing so may result in injury. Be sure confirm that the RUN signal is turned OFF before turning ON the power supply, resetting the alarm, or switching the LOCAL/REMOTE selector. Doing so while the RUN signal is turned ON may result in injury. Be sure to confirm permissible ranges of motors and machines before operation because the Inverter speed can be easily changed from low to high. Not doing so may result in damage to the product. Provide a separate holding brake when necessary. Not doing so may result in injury. Do not perform a signal check during operation. Doing so may result in injury or damage to the product. Do not carelessly change settings. Doing so may result in injury or damage to the product.
WARNING
WARNING
WARNING
WARNING WARNING
WARNING
WARNING
WARNING
! Caution
! Caution ! Caution
! Caution
4-2
Chapter 4
1. Installation and Mounting Install the Inverter according to the installation conditions. Refer to page 2-2. Ensure that the installation conditions are met. 2. Wiring and Connection Connect to the power supply and peripheral devices. Refer to page 2-7. Select peripheral devices which meet the specifications and wire correctly. 3. Power Connection Carry out the following pre-connection checks before turning on the power supply. S Always ensure that a power supply to the correct voltage is used and that the power input terminals (R/L1, S/L2, and T/L3) are wired correctly. 3G3JV-A2j: 3-phase 200 to 230 V AC 3G3JV-ABj: Single-phase 200 to 240 V AC (Wire R/L1 and S/L2) 3G3JV-A4j: 3-phase 380 to 460 V AC S Make sure that the motor output terminals (U/T1, V/T2, and W/T3) are connected to the motor correctly. S Ensure that the control circuit terminals and the control device are wired correctly. Make sure that all control terminals are turned off. S Set the motor to no-load status (i.e., not connected to the mechanical system). S Having conducted the above checks, connect the power supply. 4. Check the Display Status Check to be sure that there are no faults in the Inverter. S If the display at the time the power is connected is normal, it will read as follows: RUN indicator: Flashes ALARM indicator: Off Setting/Monitor indicators: FREF, FOUT, or IOUT is lit. Data display: Displays the corresponding data of the indicator that is lit. S When a fault has occurred, the details of the fault will be displayed. In that case, refer to Chapter 8 Maintenance Operations and take necessary remedies. 5. Initializing Parameters Initialize the parameters. S Set n01 to 8 for initialization in 2-wire sequence. 6. Setting Parameters Set the parameters required for a test run. S Set the rated motor current in order to prevent the motor from burning due to overloading. 7. No-load Operation Start the no-load motor using the Digital Operator. S Set the frequency reference using the Digital Operator and start the motor using key sequences.
4-3
Test Run
8. Actual Load Operation Connect the mechanical system and operate using the Digital Operator.
Chapter 4
S When there are no difficulties using the no-load operation, connect the mechanical system to the motor and operate using the Digital Operator. 9. Operation Basic Operation: Operation based on the basic settings required to start and stop the Inverter. Refer to page 5-1. Advanced Operation: Operation that uses PID control or other functions. Refer to page 6-1. S For operation within standard parameters, refer to Chapter 5 Basic Operation. S Refer to Chapter 5 Basic Operation and Chapter 6 Advanced Operation for the various advanced functions, such as stall prevention, carrier frequency setting, overtorque detection, torque compensation, and slip compensation.
4-4
Chapter 4
Power Connection
2
Normal
If the display is normal when the power is connected, it will read as follows: RUN indicator: Flashes ALARM indicator: Off Setting/Monitor indicators: FREF, FOUT, or IOUT is lit. Data display: Displays the corresponding data for the indicator that is lit. When a fault has occurred, the details of the fault will be displayed. In that case, refer to Chapter 8 Maintenance Operations and take necessary action. Fault RUN indicator: Flashes ALARM indicator: Lit (fault detection) or flashes (alarm detection) Setting/Monitor indicators: FREF, FOUT, or IOUT is lit. Data display: The fault code, such as UV1, is displayed. The display will differ depending on the type of fault.
4-5
Test Run
3 Initializing Parameters
Chapter 4
Initialize the parameters using the following procedure. To initialize the parameters, set n01 to 8.
Key sequence Indicator Display example Power On Press the Mode Key repeatedly until the PRGM indicator is lit. Press the Enter Key. The data of n01 will be displayed. Use the Increment or Decrement Key to set n01 to 8. The display will flash. Press the Enter Key so that the set value will be entered and the data display will be lit. The parameter number will be displayed. Explanation
In approximately 1 s.
Set the motor current parameter in n32 in order to prevent the motor from burning due to overloading.
Check the rated current on the motor nameplate and set the motor current parameter. This parameter is used for the electronic thermal function for motor overload detection (OL1). By setting the correct parameter, the overloaded motor will be protected from burning.
n32 Setting range Rated Motor Current 0.0% to 120% (A) of rated output current of the Inverter Unit of setting 0.1 A Changes during operation Default setting No (see note 1)
Note 1. The standard rated current of the maximum applicable motor is the default rated motor current. Note 2. Motor overload detection (OL1) is disabled by setting the parameter to 0.0.
Key sequence Indicator Display example Explanation Displays the parameter number. Use the Increment or Decrement Key until n32 is displayed. Press the Enter Key. The data of n32 will be displayed. Use the Increment or Decrement Key to set the rated motor current. The display will flash. Press the Enter Key so that the set value will be entered and the data display will be lit. The parameter number will be displayed.
In approximately 1 s.
4-6
Test Run
5 No-load Operation
Chapter 4
Start the no-load motor (i.e., not connected to the mechanical system) using the Digital Operator. Note Before operating the Digital Operator, check that the FREQ adjuster is set to MIN.
After changing the frequency reference or the rotation direction, check that there is no vibration or abnormal sound from the motor. Check that no faults have occurred in the Inverter during operation.
On completion of operating the motor in the no-load state in the forward or reverse direction, press the STOP/RESET Key. The motor will stop.
After checking the operation with the motor in no-load status, connect the mechanical system and operate with an actual load. Note Before operating the Digital Operator, check that the FREQ adjuster is set to MIN.
After confirming that the motor has stopped completely, connect the mechanical system. Be sure to tighten all the screws when fixing the motor axis in the mechanical system.
In case a fault occurs during operation, make sure the Stop Key on the Digital Operator is easily accessible. Use the Digital Operator in the same way as no-load operation. First set the frequency reference to a low speed of one tenth the normal operating speed.
4-7
Test Run
H Checking the Operating Status
Chapter 4
Having checked that the operating direction is correct and that the machine is operating smoothly at slow speed, increase the frequency reference. After changing the frequency reference or the rotation direction, check that there is no vibration or abnormal sound from the motor. Check the monitor display (IOUT or multi-function monitor U03) to ensure that the output current is not becoming excessive.
4-8
5
Chapter 5 Basic Operation
5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 Initial Settings V/f Control Setting the Local/Remote Mode Selecting the Operation Command Setting the Frequency Reference Setting the Acceleration/Deceleration Time Selecting the Reverse Rotation-prohibit Selecting the Interruption Mode Multi-function I/O Analog Monitor Output
Basic Operation
Chapter 5
This section explains the basic settings required to operate and stop the Inverter. The settings of parameters described here will be sufficient for simple Inverter operations. First, make these basic settings, then skip to the explanations of those special functions, even when your application requires special functions, such as stall prevention, carrier frequency setting, overtorque detection, torque compensation, slip compensation. Refer to Chapter 6 Advanced Operation.
5-1
Initial Settings
The following initial settings are required. Parameter Write-prohibit Selection/Parameter Initialization (n01): Set n01 to 1 so that n01 through n79 can be set or displayed. Rated Motor Current (n32): Check the rated current on the motor nameplate and set the parameter.
Note This parameter makes it possible to write-prohibit parameters, change the parameter set or displayed range, or initialize all parameters to default values.
Set Values
Value 0 1 5 6 8 9 Description Only n01 can be displayed and set. The n02 through n79 parameters can be displayed only. The n01 through n79 parameters can be displayed and set. Enables continuous operation. (Parameters n01 to n79 can be set or monitored.) Only the error log memory is cleared. Enables the initialization of all parameters in 2-wire sequence so that the parameters will return to default values. Enables the initialization of all parameters in 3-wire sequence.
Note With settings 0 or 1, operation commands are ignored in Program Mode. (Refer to 3-1-2 Drive Mode and Program Mode.) Normally, use a setting of 0 or 1.
5-2
Basic Operation
n32 Setting range Rated Motor Current 0.0% to 120% (A) of rated output current of Inverter Unit of setting 0.1 A
Chapter 5
Changes during operation Default setting No (see note 1)
Note 1. The standard rated current of the maximum applicable motor is the default rated motor current. Note 2. Motor overload detection (OL1) is disabled by setting the parameter to 0.0.
5-3
Chapter 5
Set the V/f pattern so that the motor output torque is adjusted to the required load torque. The 3G3JV incorporates an automatic torque boost function. Therefore, a maximum of 150% torque can be output at 3 Hz without changing the default settings. Check the system in trial operation and leave the default settings as they are if no torque characteristic changes are required.
n09 Setting range n10 Setting range n11 Setting range n12 Setting range n13 Setting range n14 Setting range n15 Setting range Maximum Frequency (FMAX) 50.0 to 400 (Hz) Maximum Voltage (VMAX) 1 to 255 (V) (See note 2.) Unit of setting Maximum Voltage Frequency (FA) 0.2 to 400 (Hz) Unit of setting 0.1 Hz (See note 1.) 1V Unit of setting 0.1 Hz (See note 1.) Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting No 60.0 No 200 (See note 2.) No 60.0 No 1.5 No 12 (See note 2.) No 1.5 No 12 (See note 2.)
Middle Output Frequency (FB) 0.1 to 399 (Hz) Unit of setting 0.1 Hz (See note 1.)
Middle Output Frequency Voltage (VC) 1 to 255 (V) (See note 2.) Unit of setting Minimum Output Frequency (FMIN) 0.1 to 10.0 (Hz) Unit of setting 0.1 Hz 1V
Minimum Output Frequency Voltage (VMIN) 1 to 50 (V) (See note 2.) Unit of setting 1V
Note 1. Values will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or greater.
5-4
Basic Operation
Chapter 5
Note 2. With 400-V Inverters, the values for the upper limit of setting ranges and the default settings will be twice those given in the above table.
Output voltage (V)
Note
1. Set the parameters so that the following condition will be satisfied. n14 x n12 < n11 x n09 2. The value set in n13 will be ignored if parameters n14 and n12 are the same in value.
Note
Frequency (Hz)
Set the rated motor input frequency to the maximum voltage frequency (FMAX) while the rated motor input voltage is set to the maximum output voltage (VMAX). The vertical-axis load or the load with high viscous friction may require high torque at low speed. If the torque is insufficient at low speed, increase the voltage in the low-speed range by 1 V, provided that no overload (OL1 or OL2) is detected. If an overload is detected, decrease the set values or consider the use of an Inverter model with a higher capacity. The required torque of fan or pump control increases in proportion to the square of the speed. By setting a quadratic V/f pattern to increase the voltage in the low-speed range, the power consumption of the system will increase.
5-5
Chapter 5
The 3G3JV operates in local or remote mode. The following description provides information on these modes and how to select them.
H Basic Concept
Operation mode Remote Basic concept The Inverter in a system operates according to the control signal of the host controller. The Inverter in a system operates independently in this mode so that the Inverter can be checked independently. Description RUN Command Selectable from two types and set in n02. Frequency Reference Selectable from five types and set in n03. RUN Command Starts with the RUN Key of the Digital Operator and stops with the STOP/RESET Key. Frequency Reference Set with the Digital Operator or the FREQ adjuster. Set with frequency reference selection in local mode in n07.
Local
The following two selection methods are available to set the Inverter to local or remote mode. While the operation command is being input, however, the Inverter cannot be set to local mode from remote mode or vice versa. S Select the mode with the LO/RE Key of the Digital Operator. S Set any one of multi-function inputs 1 through 4 (n36 through n39) to 17 to set the Inverter to local mode with control input turned ON. Note If the above setting is made, mode selection will be possible only with multi-function input, and not with the Digital Operator. The Inverter always goes into remote mode when the power is turned ON. Therefore, to operate immediately after power-up, set up the RUN command and frequency reference settings in remote mode in advance.
5-6
Chapter 5
The following description provides information on how to input operation commands to start or stop the Inverter or change the direction of rotation of the Inverter. Three types of command input methods are available. Select either one of them according to the application.
Select the method of operation mode input to start or stop the Inverter. The following method is enabled in remote mode only. The command can be input through key sequences on the Digital Operator.
n02 Setting range Operation Command Selection 0 to 2 Unit of setting 1 Changes during operation Default setting No 0
Set Values
Value 0 1 2 Description The RUN and STOP/RESET Keys of the Digital Operator are enabled. Multi-function input in 2- or 3-wire sequence through the control circuit terminals is enabled. Operation commands via RS-422/485 communications are enabled.
Set Values
Value 0 1 Description The STOP/RESET Key of the Digital Operator is enabled. The STOP/RESET Key of the Digital Operator is disabled. This setting is available only when the Digital Operator is selected for operation command input.
5-7
Chapter 5
Set Values
Value 0 1 2 3 4 6 Description The FREQ adjuster of the Digital Operator is enabled. (see note 1) Frequency reference 1 (n21) is enabled. The frequency reference control terminal (for 0- to 10-V input) is enabled. (see note 2) The frequency reference control terminal (for 4- to 20-mA current input) is enabled. (see note 3) The frequency reference control terminal (for 0- to 20-mA current input) is enabled. (see note 3) The frequency reference via RS-422/485 communications is enabled.
Note 1. The maximum frequency (FMAX) is set when the FREQ adjuster is set to MAX. Note 2. The maximum frequency (FMAX) is set with 10 V input. Note 3. The maximum frequency (FMAX) is set with 20 mA input, provided that SW8 on the control PCB is switched from V to I. The frequency reference set in n03 works as frequency reference 1 when the Inverter is in multi-step speed operation. The set values in n22 through n28 for frequency references 2 through 8 are enabled.
Two frequency references are available in local mode. Select one of them according to the application.
Changes during operation Default setting No 0
5-8
Basic Operation
Set Values
Value 0 1 Description The FREQ adjuster of the Digital Operator is enabled. (see note 1) Key sequences on the Digital Operator are enabled. (see note 2)
Chapter 5
Note 1. The maximum frequency (FMAX) is set when the FREQ adjuster is set to MAX. Note 2. The frequency reference can be set with key sequences while the FREF indicator is lit or with the set value in n21 for frequency reference 1. In either case, the value is set in n21.
H Setting the Frequency Reference Upper and Lower Limits (n30 and n31)
Set the upper and lower frequency reference limits as percentage based on the maximum frequency as 100%.
n30 Setting range n31 Setting range Frequency Reference Upper Limit 0% to 110% (Max. frequency = 100%) Frequency Reference Lower Limit 0% to 110% (Max. frequency = 100%) Unit of setting 1% Unit of setting 1% Changes during operation Default setting Changes during operation Default setting No 100 No 0
Note If n31 is set to a value less than the minimum output frequency (FMIN), the Inverter will have no output when a frequency reference less than the minimum output frequency input is ON.
5-9
Basic Operation
n42 Setting range Frequency Reference Bias 99% to 99% (Max. frequency = 100%) Unit of setting 1%
Chapter 5
Changes during operation Default setting Yes 0
The digital filter with a first-order lag can be set for analog frequency references to be input. This setting is ideal if the analog input signal changes rapidly or the signal is subject to noise interference. The larger the set value is, the slower the response speed will be.
n43 Setting range Analog Frequency Reference Filter Time 0.00 to 2.00 (s) Unit of setting 0.01 s Changes during operation Default setting No 0.10
H Setting Frequency References 1 through 8 and the Inching Frequency Command (n21 through n28 and n29)
A total of nine frequency references (frequency references 1 through 8) and an inching frequency command can be set together in the Inverter.
5-10
Basic Operation
n26 Setting range n27 Setting range n28 Setting range Frequency Reference 6 0.0 to max. frequency Unit of setting 0.01 Hz (see note 1) Changes during operation Default setting
Chapter 5
Yes 0.0
Frequency Reference 7 0.0 to max. frequency Unit of setting 0.01 Hz (see note 1)
Yes 0.0
Frequency Reference 8 0.0 to max. frequency Unit of setting 0.01 Hz (see note 1)
Yes 0.0
Note 1. Values will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or over. Note 2. Frequency reference 1 is enabled with n03 for frequency reference selection set to 1. Note 3. Frequency references 2 through 8 are enabled by setting multi-step speed references 1, 2, and 3 in n36 through n39 for multi-function input. Refer to the following table for the relationship between multi-step speed references 1 through 3 and frequency references 1 through 8.
Frequency reference Multi-step speed reference 1 (Set value: 6) OFF ON OFF ON OFF ON OFF ON Multi-step speed reference 2 (Set value: 7) OFF OFF ON ON OFF OFF ON ON Multi-step speed reference 3 (Set value: 8) OFF OFF OFF OFF ON ON ON ON
Frequency reference 1 Frequency reference 2 Frequency reference 3 Frequency reference 4 Frequency reference 5 Frequency reference 6 Frequency reference 7 Frequency reference 8
No multi-step speed reference 3 settings will be required if only frequency references 1 through 4 are used, for example. Any multi-step speed reference not set is regarded as turned-OFF input.
Note 1. The value will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or over.
5-11
Basic Operation
Chapter 5
Note 2. In order to use the inching frequency command, one of the n36 through n39 parameters for multi-function input must be set to 10 as an inching frequency command. Parameter n29 is selectable by turning on the multi-function input set with the inching frequency command. The inching frequency command takes precedence over the multi-step speed reference (i.e., when the inching frequency command is ON, all multi-step speed reference input will be ignored).
Key sequence
Indicator
Display example
Explanation Power On Note If the FREF indicator has not been lit, press the Mode Key repeatedly until the FREF indicator is lit. Use the Increment or Decrement Key to set the frequency reference. The data display will flash while the frequency reference is set. Press the Enter Key so that the set value will be entered and the data display will be lit.
5-12
Basic Operation
Set Values
Value 0 1 Description Enter Key enabled (The set value is entered with the Enter Key pressed.) Enter Key disabled (The set value set is entered immediately.)
Chapter 5
5-13
Chapter 5
The following description provides information on parameters related to acceleration and deceleration time settings. Trapezoidal and S-shape acceleration and deceleration are available. Using the Sshape characteristic function for acceleration and deceleration can reduce shock to the machinery when stopping or starting.
Note Values will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or over.
5-14
Basic Operation
H S-shape Acceleration/Deceleration Characteristic (n20)
Chapter 5
Trapezoidal and S-shape acceleration and deceleration are available. Using the S-shape characteristic function for acceleration and deceleration can reduce shock to the machinery when stopping or starting. Any one of three S-shape acceleration/deceleration times (0.2, 0.5, and 1.0 s) is selectable.
n20 Setting range S-shape Acceleration/Deceleration Characteristic 0 to 3 Unit of setting 1 Changes during operation Default setting No 0
Set Values
Value 0 1 2 3 Description No S-shape acceleration/deceleration characteristic (Trapezoidal acceleration/deceleration) S-shape acceleration/deceleration characteristic time is 0.2 s S-shape acceleration/deceleration characteristic time is 0.5 s S-shape acceleration/deceleration characteristic time is 1.0 s
Note When the S-shape acceleration/deceleration characteristic time is set, the acceleration and deceleration times will be lengthened according to the S-shape at the beginning and end of acceleration/deceleration.
5-15
Chapter 5
This parameter is used to specify whether to enable or disable the reverse rotation command sent to the Inverter from the control circuit terminals or Digital Operator. The parameter should be set to not accept when the Inverter is applied to systems that prohibit the reverse rotation of the Inverter.
Set Values
Value 0 1 Accept Not accept Description
5-16
Chapter 5
This parameter is used to specify the interruption mode when the STOP command is input. The Inverter either decelerates or coasts to a stop according to the interruption mode selection.
Set Values
Value 0 1 Description Frequency deceleration stop (See notes 1 and 2.) Free running (See note 3.)
Note 1. The Inverter will decelerate to stop according to the setting in n17 for deceleration time 1 if any of the n36 through n39 parameters for multi-function input is not set to 11 for acceleration/deceleration time selection. If any one of the n36 through n39 multi-function input parameters is set to acceleration/deceleration time selection, the Inverter will decelerate to stop according to the selected setting of deceleration time when the STOP command is input. Note 2. If the RUN signal is input again during a deceleration stop, deceleration will be stopped at the point of the input and acceleration will proceed at that frequency. Note 3. Do not input a RUN signal during a free-running stop if the motors rotation speed is not sufficient slowed. If a RUN signal is input under these conditions, a main circuit overvoltage (OV) or overcurrent (OC) will be detected. To restart a free-running motor, set a speed search command in one of the multi-function inputs 1 to 4 (n36 to n39), use the speed search to detect the speed of the free running motor, and then accelerate smoothly.
5-17
Chapter 5
Set Values
Value 0 Function Description Forward/Reverse rotation 3-wire sequence (to be set in n37 only) command By setting n37 to 0, the set value in n36 is ignored and the following setting are forcibly made. S1: RUN input (RUN when ON) S2: STOP input (STOP when OFF) S3: Forward/Reverse rotation command (OFF: Forward; ON: Reverse) Reverse rotation command (2-wire sequence) ON: External fault (FPj detection: j is a terminal number) OFF: External fault (EFj detection: j is a terminal number) ON: Fault reset (disabled while RUN command is input) Signals to select frequency references 2 through 8. Note Refer to 5-5-4 5 5 4 Setting the Frequency References through Key Sequences for the relationship between multi-step speed references and frequency q y references. Note Any multi-step speed reference not set is regarded as turnedOFF input.
2 3 4 5 6 7 8
Reverse/Stop External fault (NO) External fault (NC) Fault reset Multi-step speed reference 1 Multi-step speed reference 2 Multi-step speed reference 3
5-18
Basic Operation
Value 10 11 12 13 14 Function Inching frequency command Acceleration/Deceleration time selection External base block command (NO) External base block command (NC) Search command (Searching starts from maximum frequency) Search command (Searching starts from preset frequency) Acceleration/Deceleration-prohibit command Local or remote selection
Chapter 5
Description ON: Inching frequency command (taking precedence over the multi-step speed reference) ON: Acceleration time 2 and deceleration time 2 are selected. ON: Output shut off (while motor coasting to a stop and bb flashing) OFF: Output shut off (with motor free running and bb flashing) ON: Speed search (Searching starts from n09)
15
16 17
18 19 20 21 22 34
Communications or remote selection Emergency stop fault (NO) Emergency stop alarm (NO) Emergency stop fault (NC) Emergency stop alarm (NC) Up or down command
ON: Acceleration/Deceleration is on hold (running at parameter frequency) ON: Local mode (operated with the Digital Operator) Note After this setting is made, mode selection with the Digital Operator is not possible. ON: RS-422/485 communications input is enabled. OFF: The settings of n02 and n03 are enabled. The Inverter stops according to the setting in n04 for interruption mode selection with the emergency stop input turned ON. n04 set to 0: Decelerates to stop at deceleration time 2 set in n19. n04 set to 1: Coasts to a stop. g y stop p with the contact closed. Note NO: Emergency NC: Emergency stop with the contact opened. Note Fault: Fault output is ON and reset with RESET input. Alarm output is ON (no reset required) required). Note STP is displayed (lit with fault input ON and flashes with alarm input ON) Up or down command (set in n39 only) By setting n39 to 34, the set value in n38 is ignored and the following settings are forcibly made. S4: Up command S5: Down command Note It is impossible to set the up or down command and multi-step speed references 1 through 3 together. Note For up and down command functions in detail, refer to 6-7-7 UP/DOWN Command Frequency Memory (n62). ON: RS-422/485 communications self-diagnostic test (set in n39 only)
35
Self-diagnostic test
5-19
Basic Operation
H Operation in 2-wire Sequence (Set Value: 2)
Chapter 5
The Inverter operates in 2-wire sequence by setting a multi-function input parameter to 2 (reverse/ stop). The following diagram shows a wiring example of the terminals in 2-wire sequence.
Forward-rotation switch Reverse-rotation switch Forward/Stop (Forward rotation with the forward-rotation switch closed and reverse-rotation switch opened) Reverse/Stop (Reverse rotation with the reverse-rotation switch closed and forward-rotation switch opened) j: 2 to 5 Sequence input common
The Inverter operates in 3-wire sequence by setting n37 for multi-function input 2 to 0. Only n37 can be set to 0 (3-wire sequence). By making this setting, the set value in n36 is ignored and the following settings are forcibly made. S1: RUN input (RUN when ON) S2: STOP input (STOP when OFF) S3: Forward/Reverse rotation command (OFF: Forward; ON: Reverse) The following diagram shows a wiring example of the terminals in 3-wire sequence.
Stop switch (NC) Operation switch (NO) RUN input (RUN with the STOP switch and RUN switch closed) Direction switch STOP input (with the STOP switch opened)
Forward/Reverse rotation command (Forward rotation with the direction switch opened and reverse rotation with the direction switch closed)
5-20
Basic Operation
Chapter 5
when the frequency is other than zero, the frequency calculated at that point will be output. Because of this, if the baseblock is cleared during deceleration while the motor is free running, a large discrepancy between the motor speed at that moment and the Inverter output frequency may result in a main circuit overvoltage (OV) or overcurrent (OC).
ON 0.5 s min.
Time
Time
5-21
Basic Operation
Set Values
Value 0 1 2 3 4 5 6 Function Fault output Operation in progress Frequency detection Idling Frequency detection 1 Frequency detection 2 Overtorque being monitored (NO-contact output) Overtorque being monitored (NC-contact output) Alarm output Base block in progress RUN mode Inverter ready Fault retry UV in progress Rotating in reverse direction Speed search in progress
Chapter 5
Description ON: Fault output (with protective function working) ON: Operation in progress (with RUN command input or inverter output) ON: Frequency detection (with frequency reference coinciding with output frequency) ON: Idling (at less than min. output frequency) ON: Output frequency y frequency detection level (n58) ON: Output frequency x frequency detection level (n58) Output if any of the following parameter conditions is satisfied. Overtorque detection function selection (n59) Overtorque detection level (n60) Overtorque detection time (n61) Note NO contact: ON with overtorque being detected; NC contact: OFF with overtorque being detected ON: Alarm being detected (Nonfatal error being detected) ON: Base block in progress (in operation with output shutoff) ON: Local mode (with the Digital Operator) ON: Inverter ready to operate (with no fault detected) ON: Fault retry (Inverter resetting with fault retry (n48) not set to 0) ON: Undervoltage being monitored (main circuit undervoltage UV or UV1 detected) ON: Rotating in reverse direction ON: Speed search in progress
10 11 12 13 14 15 16 17
Note Use operation in progress (set value: 1) or idling (set value: 3) setting for the timing for stopping the motor using a brake. To specify a precise stop timing, set frequency detection 1 (set value: 4) or frequency detection 2 (set value: 5), and set the frequency detection level (n58).
5-22
Chapter 5
The analog output characteristics are set as an analog monitor output gain in n45.
Changes during operation Default setting No 0
Set Values
Value 0 1 n45 Set range Description Output frequency (Reference: 10 V at max. frequency) Output current (Reference: 10 V with rated output current) Analog Monitor Output Gain 0.00 to 2.00 Unit of setting 0.01 Changes during operation Default setting Yes 1.00
Note 1. Set the multiplication ratio based on the set value in n44. For example, if an output of 5 V is desired at maximum frequency (with n44 set to 0), set n45 to 0.50. Note 2. The maximum output voltage of the analog monitor output terminals are 10 V.
5-23
6
Chapter 6 Advanced Operation
6-1 6-2 6-3 6-4 6-5 6-6 6-7 Setting the Carrier Frequency DC Injection Braking Function Stall Prevention Function Overtorque Detection Function Torque Compensation Function Slip Compensation Function Other Functions
Advanced Operation
Chapter 6
This chapter provides information on the use of advanced functions of the Inverter for operation. Refer to this chapter to use the various advanced functions, such as stall prevention, carrier frequency setting, overtorque detection, torque compensation, and slip compensation.
6-1
Setting range
Note The default setting varies with the capacity of the Inverter model.
Set Values
Value 1 2 3 4 7 8 9 Description 2.5 kHz 5.0 kHz 7.5 kHz 10.0 kHz 2.5 kHz (12): 12 times as high as output frequency (between 1.0 and 2.5 kHz) 2.5 kHz (24): 24 times as high as output frequency (between 1.0 and 2.5 kHz) 2.5 kHz (36): 36 times as high as output frequency (between 1.0 and 2.5 kHz)
The default setting does not need any changes in normal operation. Change the default setting in the following cases. The wiring distance between the Inverter and motor is long: Set the Inverter to a lower carrier frequency. Reference carrier frequency: 10 kHz at a maximum wiring distance of 100 m and 5 kHz at a wiring distance exceeding 100 m. Excessive speed or torque dispersion at low speed: Set the carrier frequency to a lower value.
6-2
Advanced Operation
Chapter 6
Note The carrier frequency changes as shown in the following graph with 7 through 9 set in n46.
Output frequency 83.3 Hz (Set value: 7) 41.6 Hz (Set value: 8) 27.7 Hz (Set value: 9) 208.3 Hz (Set value: 7) 104.1 Hz (Set value: 8) 69.4 Hz (Set value: 9)
The Inverter cannot maintain rated output current with the carrier frequency set to a value higher than the default one. The following table shows the default value and a decrease in the output current of each Inverter model. Be sure to use the Inverter so that there will be no decrease in rated output current.
Voltage Model 3G3JVDefault setting Rated output current (A) Set to 3 Reduced rated output current (A) Set to 4 Reduced rated output current (A) 7.0 10.0 16.5 7.0 1.0 1.6 3.0 4.0 4.8 7.6
3-phase p 200 V
Single-phase g p 200 V
3-phase p 400 V
A2001 A2002 A2004 A2007 A2015 A2022 A2037 AB001 AB002 AB004 AB007 AB015 A4002 A4004 A4007 A4015 A4022 A4037
4 (10 kHz) 4 (10 kHz) 4 (10 kHz) 4 (10 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 4 (10 kHz) 4 (10 kHz) 4 (10 kHz) 4 (10 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz) 3 (7.5 kHz)
0.8 1.6 3.0 5.0 8.0 11.0 17.5 0.8 1.6 3.0 5.0 8.0 1.2 1.8 3.4 4.8 5.5 8.6
6-3
Advanced Operation
n75 Setting range Low Carrier Frequency at Low Speed 0, 1 Unit of setting 1 Changes during operation Default setting
Chapter 6
No 0
Set Values
Value 0 1 Description Low carrier frequency at low speed disabled. Low carrier frequency at low speed enabled.
Normally set n75 to 0. When the output frequency is 5 Hz or higher and the output current rate is 110% or less, the carrier frequency will be automatically reduced to 2.5 kHz with n75 set to 1. If the load is heavy at low speed, the Inverter will withstand higher overcurrent by suppressing the heat radiation of the Inverter caused by the carrier frequency. This function is enabled with 2, 3, or 4 set in n46 for carrier frequency.
6-4
Chapter 6
The DC injection braking function applies DC on the induction motor for braking control. Startup DC Injection Braking: This braking is used for stopping and starting the motor rotating by inertia with no regenerative processing. DC Injection Braking to Stop: Adjust the stop DC injection braking time if the motor rotating does not decelerate to a stop in normal operation due to inertia from a heavy load. By increasing the DC injection braking time or DC injection braking current, the time required for stopping the motor is reduced.
n52 Setting range n53 Setting range n54 Setting range DC Control Current 0 to 100 (%) Unit of setting 1% Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting No 50 No 0.5 No 0.0
Interruption DC Control Time 0.0 to 25.5 (s) Startup DC Control Time 0.0 to 25.5 (s) Unit of setting 0.1 s Unit of setting 0.1 s
Set the DC injection braking current as percentage based on the rated current of the Inverter as 100%. After the startup DC injection braking time is set, the Inverter starts up at minimum frequency on completion of the startup DC injection braking control of the Inverter. After the speed is reduced, the Inverter is switched to DC injection braking at minimum output frequency.
DC Injection Braking Control Output frequency
6-5
Chapter 6
A stall will occur if the motor cannot keep up with the rotating magnetic field on the motor stator side when a large load is applied to the motor or a sudden acceleration/deceleration is performed. In the 3G3JV, stall prevention functions can be set independently for accelerating, running, and decelerating conditions.
n55 Setting range Stall Prevention Level during Deceleration 0, 1 Unit of setting 1 Changes during operation Default setting No 0
Set Values
Value 0 1 Stall prevention during deceleration No stall prevention during deceleration Description
If 1 is set, the motor will be decelerated according to the set deceleration time. If the deceleration time is too short, the main circuit may result in overvoltage. If 0 is set, the deceleration time will be automatically lengthened to prevent overvoltage.
Stall Prevention during Deceleration with n55 Set to 0 Output frequency Deceleration time is controlled to prevent overvoltage.
6-6
Advanced Operation
n56 Setting range Stall Prevention Level during Acceleration 30 to 200 (%) Unit of setting 1% Changes during operation Set Values
Chapter 6
No 170
Set Values
This function is used to stop accelerating the load if the output current exceeds the set current value so that the Inverter will continue operating without stalling. The Inverter accelerates the load while the output current is the same as or less than the set value. Set the parameter as percentage based on the rated Inverter current as 100%. The default setting does not need any changes in normal operation. Decrease the set value if the capacity of the motor is smaller than that of the Inverter or the motor stalls with the default value. The set value is normally 2 or 3 times higher than the rated current of the motor. Set this current as percentage based on the rated inverter current as 100%.
Stall Prevention during Acceleration Output current
Time Output frequency The output frequency is controlled so that the Inverter will not stall. Time
6-7
Advanced Operation
n57 Setting range Stall Prevention during Operation 30 to 200 (%) Unit of setting 1% Changes during operation Default setting
Chapter 6
No 160
Set Values
This function will decrease the output frequency if the output current exceeds the set current value by a minimum of approximately 100 ms so that the Inverter will continue operating without stalling. The Inverter will increase the output frequency to return to the set frequency reference level when the output current is less than the set value. The Inverter accelerates or decelerates the output frequency according to the preset acceleration or deceleration time. (Acceleration time 1: n16, n17 or acceleration time 2: n18, n19) Set the parameter as percentage based on the rated Inverter current as 100%. The default setting does not need any changes in normal operation. Decrease the set value if the capacity of the motor is smaller than that of the Inverter or the motor stalls with the default value. The set value is normally 2 or 3 times higher than the rated current of the motor. Set this current in percentage based on the rated Inverter current as 100%.
Stall Prevention during Acceleration Output current
The output frequency is controlled so that the Inverter will not stall. Time
6-8
Chapter 6
When an excessive load is applied to the equipment, the Inverter detects the overtorque condition through an increase in the output current.
n59 Setting range Overtorque Detection Function Selection 0 to 4 Unit of setting 1 Changes during operation Default setting No 0
Set Values
Value 0 1 2 3 4 Description Inverter does not monitor overtorque. Inverter monitors overtorque only when speed is matched. It continues operation (issues warning) even after overtorque is detected. Inverter monitors overtorque only when speed is matched. It discontinues operation (through protective function) when overtorque is detected. Inverter always monitors overtorque during operation. It continues operation (issues warning) even after overtorque is detected. Inverter always monitors overtorque during operation. It discontinues operation (through protective function) when overtorque is detected.
Set n60 for overtorque detection level and n61 for overtorque detection time to enable the overtorque detection function. The Inverter will detect overtorque when the current the same as or higher than the detection level is output for the preset detection time. Set n40 for multi-function output to either of the following so that external overtorque detection output will be ON. Set Value: 6 for overtorque detection (NO) Set Value: 7 for overtorque detection (NC)
Overtorque Detection Output current See note. n60 (Overtorque detection level)
Time Note Overtorque detection will be canceled if the output current decreases from the detection level by approximately 5% of the Inverter rated current.
No 160
6-9
Advanced Operation
Set Values
Set the parameter as percentage based on the rated Inverter current as 100%.
n61 Setting range Overtorque Detection Time 0.1 to 10.0 (s) Unit of setting 0.1 s Changes during operation Default setting
Chapter 6
No 0.1
Set Values
Set the overtorque detection time. The Inverter will detect overtorque when the current the same as or higher than the detection level is output for the preset detection time.
6-10
Chapter 6
This function increases the output torque of the Inverter by detecting an increase in the motor load.
n63 Setting range Torque Compensation Gain 0.0 to 2.5 Unit of setting 0.1 Changes during operation Default setting Yes 1.0
Set Values
The default setting does not need any changes in normal operation. Change the default setting in the following cases. The wiring distance between the Inverter and motor is long: Set the gain to a larger value. The capacity of the motor is lower than the maximum applicable motor capacity of the Inverter: Set the gain to a larger value. The motor vibrates: Set the gain to a smaller value. The torque compensation gain must be adjusted so that the output current at low speed will not exceed 50% of the rated output current of the Inverter, otherwise the Inverter may be damaged.
6-11
Chapter 6
The slip compensation function calculates the motor torque according to the output current, and sets gain to compensate for output frequency. This function is used to improve speed accuracy when operating with a load.
n64 Setting range Motor Rated Slip 0.0 to 20.0 (Hz) Unit of setting 0.1 Hz Changes during operation Default setting Yes (see note)
Note The default setting varies with the capacity of the Inverter model.
Set Values
Set the rated slip value of the motor in use. This parameter is used as a slip compensation constant. Calculate the rated motor slip value from the rated frequency (Hz) and rpm on the motor nameplate by using the following formula. Rated slit value (Hz) + Rated frequency (Hz)
n65 Setting range Motor No-load Current 0 to 99 (%) Unit of setting 1%
Rated rpm
Note The default setting varies with the capacity of the Inverter model.
Set Values
Set the motor current with no load in percentage based on the rated motor current as 100%. Contact the motor manufacturer for the motor current with no load. This parameter is used as a slip compensation constant.
n66 Setting range Slip Compensation Gain 0.0 to 2.5 Unit of setting 0.1 Changes during operation Default setting Yes 0.0 (see note)
Set Values
Set the parameter to 1.0 first and check the operation of the Inverter. Then fine-tune the gain with 0.1-gain increments or decrements. If the speed is lower than the target value, increase the set value. If the speed is higher than the target value, decrease the set value.
n67 Setting range Slip Compensation Time Constant 0.0 to 25.5 (s) Unit of setting 0.1 s Changes during operation Default setting No 2.0
6-12
Advanced Operation
Set Values
Chapter 6
This parameter is used for the response adjustment of the slip compensation function. The default setting does not need any changes in normal operation. Change the default setting in the following cases. The motor vibrates: The motor response is low: Set the value to a larger value. Set the value to a smaller value.
6-13
Chapter 6
The following description provides information on the other functions and parameter settings of the Inverter.
Set Values
Value 0 1 2 Description Protection characteristics for general-purpose induction motors Protection characteristics for Inverter-dedicated motors No protection
This parameter is used to set the electric thermal characteristics of the motor to be connected. Set the parameter according to the motor. If a single Inverter is connected to more than one motor, set the parameter to 2 for no protection. The parameter is also disabled by setting n32 for rated motor current to 0.0. To protect each motor from overload, be sure to take an appropriate measure such as the installation of a thermal relay.
n34 Setting range Motor Protection Time 1 to 60 (min) Unit of setting 1 min Changes during operation Default setting No 8
Set Values
This parameter is used to set the electronic thermal protection constant of motor overload detection OL1. The default setting does not need any changes in normal operation. To set the parameter according to the characteristics of the motor, confirm the thermal time constant with the motor manufacturer and set the parameter with some margin. In other words, set the value a little shorter than the thermal time constant. To detect motor overloading more quickly, reduce the set value, provided that it does not cause any application problems.
6-14
Advanced Operation
Set Values
Value 0 1
Chapter 6
Description The fan rotates only while the RUN command is input and for 1 minute after the Inverter stops operating. The fan rotates while the Inverter is turned on.
This parameter is available only if the Inverter incorporates a cooling fan. If the operation frequency of the Inverter is low, the life of the fan can be prolonged by setting the parameter to 0.
Set Values
Value 0 1 2 Description Disabled. (An undervoltage fault will be detected when there is momentary power interruption for 15 ms or more.) The Inverter will continue operating if power is restored within 0.5 s. (see note 1) The Inverter will restart when power is restored. (see note 2)
Note 1. If the parameter is set to 1, an undervoltage warning will be detected and the output of the Inverter will be shut off for 0.5 s when a momentary power interruption occurs. The Inverter will restart after speed searching if power is restored within 0.5 s. Undervoltage fault 1 will be detected if power failure continues for more than 0.5 s. Note 2. If the parameter is set to 2, an undervoltage warning will be detected and the output of the Inverter will be shut off when a momentary power interruption occurs. The Inverter will then wait for power restoration. When power is restored, the Inverter will restart after speed searching.
The Inverter may be break if the fault retry function is used. If the Inverter breaks, take the following measures: Be sure to install a no-fuse breaker (NFB). Provide the Inverter and peripheral machines with a sequence so that the machines will stop operating when the Inverter has an operational fault.
6-15
Advanced Operation
Chapter 6
The fault retry function automatically resets and restarts the Inverter in the case the Inverter has an overvoltage fault, overcurrent fault, or ground fault. In the case of any other fault, the protective function operates instantly and the fault retry function does not operate. This function is to be used only if the user does not want to interrupt the mechanical system, even if this function may damage the Inverter. Set n40 for multi-function output to the following value so that external overtorque detection output will be turned on. Set value: 14 for fault retries
n48 Setting range Fault Retry 0 to 10 Unit of setting 1 Changes during operation Default setting No 0
Set Values
Set the number of fault retries required. The count of fault retries will be cleared in any of the following cases. The Inverter is normal for 10 minutes continuously after the latest fault retry was made. Power supply to the Inverter is interrupted. A fault reset is input.
Jump Frequency 2 0.0 to 400 (Hz) Setting range 0.1 Hz (see note)
No 0.0
No 0.0
Note Values will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or greater.
6-16
Advanced Operation
Set Values
Chapter 6
Set n49 and n50 for jump frequencies 1 and 2 to the central values of jumping frequencies. These values must satisfy the following condition. n49 y n50 The value in n51 must be set for the jump width. This function is disabled with n51 set to 0.0. The operation of the Inverter within the dead bands is prohibited. While the Inverter is in acceleration or deceleration control, however, the Inverter does not jump the bands but changes the frequency smoothly.
Frequency Jump Function Output frequency
Reference frequency
6-17
Advanced Operation
H Frequency Detection
Chapter 6
The parameter n40 for multi-function output must be set for frequency detection output. Set value: 2 for frequency detection
Frequency Detection Operation Output frequency Detection width 2 Hz Reset width 4 Hz Frequency reference
Time
The parameter n40 for multi-function output must be set for frequency detection output. Set value: 4 for frequency detection level 1 (Output frequency y n58) Set value: 5 for frequency detection level 2 (Output frequency x n58) Set the frequency detection level in n58.
n58 Setting range Frequency Detection Level 0.0 to 400 (Hz) Unit of setting 0.1 Hz (see note) Changes during operation Default setting No 0.0
6-18
Advanced Operation
Chapter 6
Note The value will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or over.
Frequency Detection Level 1 Output frequency Reset width 2 Hz n58 (Frequency detection level)
Time
Frequency Detection Level 2 Output frequency Reset width +2 Hz n58 (Frequency detection level)
Time
6-19
Advanced Operation
n62 Setting range Frequency Hold Function Selector 0, 1 Unit of setting 1 Changes during operation Default setting
Chapter 6
No 0
Set Values
Value 0 1 Description The frequency on hold is not retained. The frequency on hold for 5 s or more is retailed.
Operation of UP/DOWN Function RUN command (Forward rotation) UP command (S4) DOWN command (S5) Time Output frequency Upper limit
Time
Time
Time
D: DOWN (deceleration) H: Hold U1: Frequency acceleration restricted by upper limit. D1: Frequency deceleration restricted by lower limit.
With the UP/DOWN function used, the output frequency has the following restrictions for upper and lower limits. Upper limit: Lower limit: The maximum frequency in n09 or the frequency reference upper limit in n30, whichever is smaller. The minimum output frequency in n14 or frequency reference lower limit in n31, whichever is smaller.
6-20
Advanced Operation
Chapter 6
When the RUN command for forward or reverse rotation is input, the Inverter will start operating at the lower limit regardless of whether the UP/DOWN command is input or not. When the UP/DOWN function and inching frequency command are both assigned to multi-function inputs, an inching frequency command input will have the highest priority. If n62 for UP/DOWN command frequency memory is set to 1, the output frequency held by the UP/ DOWN function for 5 s or more will be stored in the memory. The output frequency will be held by the UP/DOWN function when both UP and DOWN commands are ON or OFF together.
Display Example
D Fault display uU 1 D No error stored
Fault code
To clear the error history, set n01 for parameter write-prohibit selection/parameter initialization to 6.
6-21
7
Chapter 7 Communications
7-1 7-2 7-3 7-4 7-5 7-6 7-7 7-8 7-9 7-10 RS-422/485 Communications Unit Inverter Settings Message Communications Basic Format DSR Message and Response Enter Command Setting the Communications Data Register Number Allocations in Detail Communications Error Codes Self-diagnostic Test Communications with Programmable Controller
Communications
Chapter 7
Using a 3G3JV-PSI485J RS-422/485 Communications Unit allows 3G3JV Inverters to participate in RS-422/485 serial communications. This makes Inverter control input, frequency reference input, monitoring of the Inverters operating status, and reading and writing of parameter settings all possible via communications. Up to 32 Inverters can be connected to the Unit to enable easy creation of networks. Note 1. The RS-422/485 communications used by 3G3JV Inverters conforms to the MODBUS (a trademark of AEG Schneider Automation) communications protocol. No other communications protocol can be used in the same network and only Inverters and related products can be used as Slaves. Note 2. The communications processing time with RS-422/485 communications for 3G3JV Inverters is proportional to the number of Slaves. When performing Inverter control, consider the communications processing time, and restrict the number of Inverters connected according to the response times required. Note 3. The communications timeout time with RS-422/485 communications is fixed at 2 s (when communications timeouts are enabled). In the worst case, problems with the communications line may not be detected for up to 2 s. Design the application and overall system to ensure safety allowing for this.
7-1
7-1-1 Overview
The 3G3JV-PSI485J RS-422/485 Communications Unit is an Optional Unit for 3G3JV Inverters. Mounting an RS-422/485 Communications Unit to a 3G3JV Inverter provides the Inverter with an RS-422/485 interface.
7-2
Chapter 7
H Terminal Block
1 S S+ 2 Shield 3 R 4 R+ 5
Note Set the terminating resistance switch to ON to connect the terminating resistance.
7-3
Communications
3. Remove the optional cover as shown on the right below.
Chapter 7
4. Align the Unit with the Inverters connector, and push the Unit onto the Inverter (so that the 3 catches enter the corresponding holes) until it is securely mounted.
Connector
5. Mount the front cover (removed previously) on top of the RS-422/485 Communications Unit, and secure it using the front cover mounting screws. (Do not mount the optional cover.) Note When not using the RS-422/485 Communications Unit, be sure to mount the optional cover. Not mounting the optional cover will leave charged parts exposed and may result in electric shock or damage to equipment.
7-4
Chapter 7
Set Values
Value 0 1 2 3 4 Description Detects a time-over and fatal error and coasts to a stop (See note 1.) Detects a time-over and fatal error and decelerates to a stop in deceleration time 1 (See note 1.) Detects a time-over and fatal error and decelerates to a stop in deceleration time 2 (See note 1.) Detects a time-over and nonfatal error warning and continues operating. The warning is canceled when the communications return to normal. (See note 2.) No time-over is detected.
Note 1. The fatal error is canceled with error reset input. Note 2. The nonfatal error warning is canceled when the communications returns to normal.
Set this parameter to the unit of frequency reference and frequency-related values to be set or monitored through communications. This unit is for communications use only and independent from the units of setting made through the Digital Operator.
n69 RS-422/485 Communications Frequency Reference/Display Unit Selection 0 to 3 Register 0145 Hex Changes during operation Default setting No
Setting range
Unit of setting
7-5
Communications
Set Values
Value 0 1 2 3 Description 0.1 Hz 0.01 Hz Converted value based on 30,000 as max. frequency 0.1% (Max. frequency: 100%)
Chapter 7
Note Communications data after the above conversion is hexadecimal. For example, if the frequency is 60 Hz and the unit of setting is 0.01 Hz, the converted value is obtained as follows: 60/0.01 = 6000 = 1770 Hex
Set Values
Value 00 01 to 32 Description Only receives broadcast messages from the Master (See note.) Slave address
Note Address 00 is for broadcast purposes only. Do not set the Slave to this address, otherwise the Slave will not communicate.
Set Values
Value 0 1 2 3 2,400 bps 4,800 bps 9,600 bps 19,200 bps Description
7-6
Communications
n72 Setting range RS-422/485 Parity Selection 0 to 2 Register Unit of setting 0148 Hex 1
Chapter 7
Changes during operation Default setting No 0
Set Values
Value 0 1 2 Even Odd No parity Description
In normal serial communications, data is configured in single bytes, and messages are created by stringing together multiple bytes of data. The parity check described here sets the check for each byte of data. Set the parity check method that is required by the Master. Note The entire message is checked by a separate check code called CRC-16, so the communications data will be checked even if no special parity check is performed.
Set Values
When the DSR message is received from the Master, the Inverter must wait for a communications time of 24-bit length plus the set value in n73 before returning a response. Set this value according to the response time of the Master.
Set Values
Value 0 1 Description Enabled Disabled (Available to 1-to-1 RS-422 communication only)
7-7
Chapter 7
This parameter is enabled in remote mode only. The Inverter in local mode accepts the RUN command only through key sequences on the Digital Operator.
n02 Setting range Operation Command Selection 0 to 2 Register Unit of setting 0102 Hex 1 Changes during operation Default setting No 0
Set Values
Value 0 1 2 Description The RUN Key and STOP/RESET Key on the Digital Operator are enabled. Multi-function input terminals are enabled in 2- or 3-wire sequence. RS-422/485 communications are enabled.
Note 1. To input the RUN command through RS-422/485 communications, set this parameter to 2. Then the RUN command only through RS-422/485 communications will be enabled. Note 2. The RUN command can be input through RS-422/485 with multi-function input settings as well. For details, refer to 7-2-4 Setting the Multi-function Inputs.
Set Values
Value 0 1 2 3 4 6 Description The FREQUENCY adjuster on the Digital Operator is enabled. Frequency reference 1 (n21) is enabled. Frequency reference control terminal for 0- to 10-V voltage input is enabled. Frequency reference control terminal for 4- to 20-mA current input is enabled. Frequency reference control terminal for 0- to 20-mA current input is enabled. Frequency reference through communications is enabled.
Note 1. To input the frequency reference through RS-422/485 communications, set this parameter to 6. Then the frequency reference only through RS-422/485 communications will be enabled. Note 2. The frequency reference can be input through RS-422/485 with multi-function input settings as well. For details, refer to 7-2-4 Setting the Multi-function Inputs. Note 3. The setting of n03 is valid for frequency reference 1, and is not related to frequency references 2 to 8. Frequency references 2 to 8 are set in n22 to n28.
7-8
Chapter 7
In addition to the methods described above, the RUN command and frequency reference can be input through RS-422/485 communications by setting the value 18 in any one of the parameters from n36 to n39 (multi-function input). Subsequently, the following operations are selectable in remote mode. None of these parameters, however, can be changed while the operation command is being input. When the function-set input terminal is OFF, the RUN command will be executed according to the setting in n02 (operation command selection) and the frequency reference will be executed according to the setting in n03 (frequency reference selection). When the function-set input terminal is ON, the Inverter will operate according to the RUN command and frequency reference through RS-422/485 communications.
n36 Setting range n37 Setting range n38 Setting range n39 Setting range Multi-function input 1 (S2) 2 to 8, 10 to 22 Multi-function input 2 (S3) 0, 2 to 8, 10 to 22 Multi-function input 3 (S4) 2 to 8, 10 to 22 Multi-function input 4 (S5) 2 to 8, 10 to 22, 34, 35 Register Unit of setting Register Unit of setting Register Unit of setting Register Unit of setting 0124 Hex 1 0125 Hex 1 0126 Hex 1 0127 Hex 1 Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting Changes during operation Default setting No 2 No 5 No 3 No 6
7-9
Chapter 7
The following description provides information on the format of message data (DSR and response data). Message communications of the Inverter conform to the MODBUS Communications Protocol, which does not require message start and end processing. (The MODBUS Communications Protocol is a trademark of AEG Schneider Automation.)
H Communications Format
The following format is used for message data communications. Message data consists of a Slave address, function code, communications data, and error check block.
Message data (DSR message and response) Slave address 1 byte Function code 1 byte Communications Error check block data 2 bytes
H Message Interval
When the Inverter receives a DSR message from the Master, the Inverter waits for a period that is equivalent to 24 bits in length and a Send Wait Time set in n73. Then the Inverter will return a response. Set n73 according to the Masters processing time or the timing adjustment. When the Master issues the next message after receiving the response from the Inverter, the Master must wait for a 24-bit period plus another period of at least 10 ms.
DSR message from Master
The communications message is configured entirely of hexadecimal data. (ASCII and FINS are not used.) Communications data is divided into the four areas shown in the following table.
Data name Slave address Description Set the Slave address (the set value in n70) of the Inverter, to which the DSR message is sent. The Slave address must be within a range from 00 to 32 (00 to 20 Hex). A command giving instructions of the details of processing to the Inverter. Example: Data read (03 Hex) and data write (10 Hex) Data attached to the command. Example: The register number of read start data and the number of registers of read data CRC-16 check code for checking the reliability of the message data.
Error check
7-10
Communications
Chapter 7
Note In the above communications, the default is 1 (65535) and the LSB (least-significant byte) is converted as MSB (most-significant byte) (in the opposite direction). The CRC-16 check is automatically performed by using the protocol macro function of OMRONs SYSMAC CS/CJ-series, C200HX/HG/HE, or CQM1H Programmable Controllers.
H Slave Address
The Master can communicate with a maximum of 32 Slaves over RS-422/485. A unique Slave address is allocated to each Slave (Inverter) for communications. Slave addresses are within a range from 00 to 32 (00 through 20 Hex). If a DSR message is issued to Slave address 00, the message will be a broadcast message. Note The broadcast message is addressed to all Slaves. Only the RUN command (register 0001 Hex) and frequency command (register 0002 Hex) can be written to the message. The Inverter receiving this message does not return a response regardless of whether or not the message is received properly. Therefore, for measures against communications errors, the monitor function of the Inverter should be used for checking the reception of broadcast messages.
H Function Code
The function code is a command giving instructions of the details of processing to the Inverter. The following three functions codes are available.
Function code 03 Hex Command name Data read Description Reads the data of the specified register number. Consecutive data of a maximum of 16 words (32 bytes) can be read. The DSR message is returned as a response. This command is used for checking the status of communications. The attached data in the format is written to the specified register number. Consecutive data of a maximum of 16 words (32 bytes) can be written.
08 Hex
Loop-back test
10 Hex
Data write
Note 1. Do not use any code other than the above, otherwise the Inverter will detect a communications error and return an error message. Note 2. The Inverter uses the same function code for the response. If an error occurs, however, the MSB of the function code will be set to 1. For example, if an error occurs in a DSR message with function code 03, the function code of the response will be 83.
H Communications Data
Communications data is attached to the command. The contents and its arrangement of communications data vary with the function code. For details, refer to 7-4 DSR Message and Response.
7-11
Communications
H Error Check
Chapter 7
The CRC-16 check code is the remainder (16 bits) when all of the message blocks from the Slave address to the final communications data are connected in series, as shown in the following diagram, and this data is divided by a fixed 17-digit binary number (1 1000 0000 0000 0101).
8 bits The LSB of the Slave address is handled as the MSB in CRC-16 calculation.
Slave address
Note 1. Normally 0 is used as the initial value for CRC-16 calculations, but 1 (16 bits all 1) is used here. Note 2. The CRC-16 code is calculated with the LSB of the Slave address handled as the MSB, and the final MSB of the communications data handled as the LSB. Note 3. Calculate the CRC-16 code for responses from the Slave as well, and compare it with the CRC-16 code in the response message.
Function code
7-12
Chapter 7
The following description provides information on how to set DSR messages and what details are returned as responses. Each DSR message or response is divided into 8-bit blocks. Therefore, data must be set in 8-bit blocks for communications.
To read data (such as control I/O status data, monitor item data, or parameter set value data) from the Inverter, issue the following DSR message. Data read is a maximum of 16 words in length (i.e., data of 32 bytes from 16 registers) per DSR message. A register number is allocated to each function item, such as control I/O, monitor item, and parameter functions. The register number of each parameter is indicated wherever the parameter is explained in this manual and in Section 10 List of Parameters. For register numbers other than those of parameters, refer to 7-7 Register Number Allocations in Detail. Note 1. A parameter corresponds to one register (one word), so the number of registers of read data indicates the number of parameters to be read (i.e., the number of consecutive registers beginning with the first register number). Note 2. The number of bytes of attached data indicates the number of bytes of data read from the registers attached from that point onwards. The number of registers must equal the number of bytes divided by two.
D DSR Message
Byte No. 1 2 3 4 5 6 7 8 Slave address Function code (03 Hex) Register g No. of read start data Number of registers of read data ( (16 max.) g ) CRC-16 check Data
7-13
Communications
D Response Normal
Byte No. 1 2 3 4 5 6 7 8 9 : n1 n CRC-16 check Slave address Function code (03 Hex) Number of bytes of attached data Data of start register g Data of next register g Data of next register g : Data
Chapter 7
Error
Byte No. 1 2 3 4 5 Slave address Function code (83 Hex) Error code CRC-16 check Data
Note When an error occurs, the MSB of the function code will be set to 1.
D DSR Message
Byte No. Data Data example (Hex) 02 03 00 20 00 04 45 F0
1 2 3 4 5 6 7 8
Slave address Function code Register g No. of read start data Number of registers g of read data CRC-16 check
7-14
Communications
D Response Normal
Byte No. Data
Chapter 7
1 2 3 4 5 6 7 8 9 10 11 12 13
Slave address Function code Number of bytes of attached data Data in register g No. 0020 Data in register No. 0021 g Data in register g No. 0022 Data in register g No. 0023 CRC-16 check
Error
Byte No. Data Data example (Hex) 02 83 03 F1 31
1 2 3 4 5
7-15
Communications
D DSR Message
Byte No. 1 2 3 4 5 6 7 8 9 10 11 12 13 : n1 n CRC-16 check Slave address Function code (10 Hex) Register g No. of write start data Number of registers g of write data (16 ( max.) ) Data of start register Data of next register g Data of next register g Data of next register g : Data
Chapter 7
D Response Normal
Byte No. 1 2 3 4 5 6 7 8 Slave address Function code (10 Hex) Register g No. of write start data Number of registers g of write data CRC-16 check Data
Error
Byte No. 1 2 3 4 5 Slave address Function code (90 Hex) Error code CRC-16 check Data
Note 1. When an error occurs, the MSB of the function code will be set to 1. Note 2. A broadcast message uses the same DSR message format. The Slave address is, however, always set to 00 and only register 0001 Hex (the RUN command) and register number 0002 Hex (the frequency reference) can be written.
7-16
Communications
H Example of Data Read
Chapter 7
In the following example, two-register data (the RUN command) is written from register 0002 Hex of the Inverter with a Slave address of 01.
D DSR Message
Byte No. Data Data example (Hex) 01 10 00 01 00 02 04 00 01 02 58 63 39
1 2 3 4 5 6 7 8 9 10 11 12 13
Slave address Function code Register g No. of write start data Number of registers of write data g Data of start register Data in register g No. 0001 Data in register No. 0002 g CRC-16 check
D Response Normal
Byte No. Data Data example (Hex) 01 10 00 01 00 02 10 08
1 2 3 4 5 6 7 8
Slave address Function code Register g No. of write start data Number of registers g of write data CRC-16 check
Error
Byte No. Data Data example (Hex) 01 90 02 DC C1
1 2 3 4 5
7-17
Chapter 7
The DSR message from the Master is returned as a response. The Inverter does not retrieve or process this data. The DSR message or normal response for loop-back test use is divided into 8-byte blocks as shown below. Any data can be set as test data 1 or 2 provided that the number of data items remains changed. This command is used for checking the status of communications or for dummy communications without detecting any communications time-over.
D DSR Message
Byte No. 1 2 3 4 5 6 7 8 Slave address Function code (08 Hex) Test data 1 Test data 2 CRC-16 check Data
D Response Normal
Byte No. 1 2 3 4 5 6 7 8 Slave address Function code (08 Hex) Test data 1 Test data 2 CRC-16 check Data
Error
Byte No. 1 2 3 4 5 Slave address Function code (88 Hex) Error code CRC-16 check Data
Note When an error occurs, the MSB of the function code will be set to 1.
7-18
Communications
H Example of Loop-back Test
D DSR Message
Byte No. Data
Chapter 7
In the following example, a loop-back test is conducted on the Inverter with a Slave address of 01.
1 2 3 4 5 6 7 8
Slave address Function code Test data 1 Test data 2 CRC-16 check
D Response Normal
Byte No. Data Data example (Hex) 01 08 00 00 A5 37 DA 8D
1 2 3 4 5 6 7 8
Slave address Function code Test data 1 Test data 2 CRC-16 check
Error
Byte No. Data Data example (Hex) 01 88 01 86 50
1 2 3 4 5
7-19
Chapter 7
The Enter command is used for copying parameter set values that have been written through communications in and after register 0101 Hex of the RAM area to the EEPROM of the Inverter. This is done so that the EEPROM can maintain the parameter set values. By issuing a DSR message to write data, the data is written to the RAM area of the Inverter. This data will be lost when the Inverter is turned OFF. Issue the Enter command to store in the EEPROM of the Inverter the parameter set value that has been written through communications. Note The Enter command is not accepted while the Inverter is running. Be sure to issue the Enter command while the Inverter is not running.
The Enter command is issued in response to the DSR message (with a function code of 10 Hex) to write data. By writing data 0000 Hex to be sent to register 0900 Hex, the Inverter copies to the EEPROM all parameter set values that the Inverter has received. Note 1. Only the parameter constants (in and after register 0101 Hex) are stored in the EEPROM with the Enter command. The RUN command (in register No. 0001 Hex) is in the RAM area. The frequency reference (in register 0002 Hex) or any other data in registers with a number up to 003D Hex is also in the RAM area. Therefore, the EEPROM does not store these parameters. Note 2. Data can be written to the EEPROM a maximum of approximately 100,000 times. Therefore, be sure to reduce the number of Enter commands sent as much as possible.
7-20
Chapter 7
The following description provides information on how to convert the register data (such as monitor value or parameter set value data) in the communications data block of the message data (such as DSR and response data).
The data in each register is sent as 2-byte data. The data in each register is processed under the following rules and sent in hexadecimal.
D The data is converted to a hexadecimal value based on the minimum unit of setting of each register as 1. If the frequency reference is 60 Hz and the minimum unit of setting will be 0.01 Hz, the data will be converted as follows:
60 (Hz)/0.01 (Hz) = 6000 = 1770 Hex Note 1. The minimum unit of setting of each parameter is indicated whenever the parameter is explained in Section 10 List of Parameters. For registers other than those of parameters, refer to 7-7 Register Number Allocations in Details. Note 2. The minimum unit of setting of frequency reference data or frequency monitor data is determined by n69 (register 0145 Hex: RS-422/485 communications frequency reference/monitor unit selection). The unit of setting of each of the three registers below is determined by the set value in n69. For the units of setting of these constants, refer to the List of Parameters. The set value in n69 has nothing to do with frequency data items set as parameter constants (e.g., frequency references 1 through 8, inching frequency reference, maximum frequency, minimum output frequency, jump frequency). S Monitor Items Register 0023: Frequency reference monitor Register 0024: Output frequency monitor S Communications-dedicated Register Register 0002: Frequency reference In spite of the set value in n69, however, set the maximum frequency to 3000 when the frequency reference is executed with a broadcast message. In this case, the Inverter rounds off any value less than 0.01 Hz. Note 3. There are parameters that make setting unit changes when the values are increased with the Digital Operator. The smaller units are, however, used for communications in such cases. For example, the value in n49 (register 0131 Hex: jump frequency 1) will be set in 0.01-Hz increments if the frequency is less than 100 Hz and 0.1-Hz increments if the frequency is 100 Hz or over. The value 0.01 Hz is always 1 Hex for communications.
If the jump frequency is 100.0 Hz, the minimum unit of setting will be 0.01 Hz and the data will be converted as follows:
100.0 (Hz)/0.01 (Hz) = 10000 = 2710 Hex
7-21
Communications
D Negative Values Expressed in 2s Complements
Chapter 7
If the frequency reference bias in n42 is 100%, the minimum unit of setting will be 1% and the data will be converted as follows:
100 (%)/1 (%) = 100 = 0064 Hex 2s complement: FF9C Hex
Bit reversed.
1 is added.
Note Whether the data is positive or negative is determined by the parameter set value. The MSB of negative-value data is always set to 1. Data with its MSB set to 1 is not, however, always negative-value data.
Bits 9 through 15 of the RUN command (register 0001 Hex) are unused. When writing the data, be sure to set all of these bits to 0. These bits when read are set to 0.
Registers described not used may be used for internal processing. Do not write any data to such registers.
7-22
Chapter 7
The following description provides information on register numbers allocated to the Inverter and the meanings of the registers. As for the register numbers of the parameters (n01 through n79), refer to Section 10 List of Parameters and the description of each of these parameters wherever explained in this manual.
Note 1. The V/f gain is a rate to be multiplied by the output voltage obtained from V/f operation. If 1000 (03E8 Hex) is set, the multiplication rate will be 1. Note 2. When the above registers are read, values that are set through communications will be read. For example, when the RUN command (register 0001) is read, the control input in the register that was previously set through communications will be returned. This is not a value monitored through the input signal terminal. To monitor the actual status of the Inverter, use the monitor functions (refer to 7-7-2 Monitor Functions).
7-23
Communications
Chapter 7
Note There is an OR relationship between input from the control terminals and input through communications, except for the RUN command and forward/reverse rotation command.
Note The settings will be enabled if multi-function output n40 is set to 18 for communications output. Then the output terminals (MA to MC) will be turned ON and OFF through communications.
Write
Description --Refer to the table below. Set the frequency reference based on the maximum frequency as 30,000. ---
Note 1. Data can be written to registers 0001 and 0002 only. Assumed previous values are held for unused registers. Note 2. No data can be written to multi-function input. Note 3. The unit of setting of the broadcast message is different from that in the DSR message to communicate with a single Slave.
7-24
Communications
Register No. (Hex) 0027 0028 0029 to 002A 002B 002C 002D 002E to 0030 0031 0032 to 003C 003D 003E to 00FF Function Output current Output voltage Not used. Input terminal status Inverter status 1 Output terminal status Not used. Main circuit DC voltage Not used. Communications error Not used. Description
Chapter 7
Read based on 1 A as 10. Read based on 1 V as 1. --Refer to the following corresponding table. Refer to the following corresponding table. Refer to the following corresponding table. --Read based on 1 V as 1. --Refer to the following corresponding table. ---
7-25
Communications
D Input Terminal Status (Register 002B Hex)
Bit No. 0 1 2 3 4 5 to 15 Function Forward/stop terminal (S1) (1: ON) Multi-function input terminal 1 (S2) (1: ON) Multi-function input terminal 2 (S3) (1: ON) Multi-function input terminal 3 (S1) (4: ON) Multi-function input terminal 4 (S5) (1: ON) Not used.
Chapter 7
7-26
Chapter 7
The Inverter will detect a communications error if normal communications fail or a message data error occurs. The Inverter returns a response that consists of the Slave address, function code with the MSB set to 1, error code, and CRC-16 check block when the communications error is detected. When the Master receives an error code, refer to the following table for troubleshooting and remedying the error.
03 Hex
Check and correct the number of registers or the number of bytes. Check the display p y on the h Di Digital i lO Operator and correct the data.
21 Hex
7-27
Communications
Error code 22 Hex Name Write mode error Probable cause The Inverter in operation received a DSR message to write data to a parameter that prohibits any data to be written while the Inverter is running. The Enter command was received while the Inverter is running. The Inverter detecting UV received a DSR message to write data. The Inverter detecting UV received the Enter command. The Inverter detecting F04 for an initialization memory fault received a DSR message other than that for parameter initialization (with n01 set to 8 or 9). The Inverter processing data written received a DSR message to write data.
Chapter 7
Remedy Write the data after stopping the Inverter.
Write the data after restoring the UV (main circuit undervoltage) status. Turn the Inverter OFF and ON after parameter initialization with n01 set to 8 or 9. Wait for an elapse period equivalent to 24 bits plus a minimum of 10 ms to issue the message after a response is received from the Inverter. Check and correct the register number.
7-28
Chapter 7
The Inverter incorporates a self-diagnostic test function that checks whether RS-422/485 communications are functioning. If the Inverter has a communications failure, take the steps provided below to check whether the communications function of the Inverter is normal.
3. Turn ON the Inverter and Check the Display S Turn ON the Inverter. S Check the display on the Digital Operator. Normal The display is normal with no error code displayed. Fault The display shows CE (communications time-over) or CAL (communications standby). In either case, the communications circuit of the Inverter is broken. Replace the Inverter.
7-29
Chapter 7
The Communications Board/Unit can be mounted to OMRONs SYSMAC CS/CJ-series, C200HX/HG/HE, or CQM1H CPU Units. The Inverter can then be controlled by the Communications Board/Unit through its RS-422/485 port. The communications protocol can be set by using the protocol macro function. Therefore, there is no need to write a ladder program for the communications protocol when the function is used. The following description provides information on how to control the Inverter through communications with the SYSMAC CS/CJ-series, C200HX/HG/HE, or CQM1H Communications Board/Unit by using the protocol macro function. The RS-422/485 communications of the 3G3JV Inverter conform to the MODBUS Communications Protocol and this protocol cannot be used together with CompoBus/D communications protocol or any other communications protocol. Only 3G3JV-series Units can be connected as Slaves. (The MODBUS Communications Protocol is a trademark of AEG Schneider Automation.)
The Communications Board can be mounted to the following SYSMAC CPU Units.
CPU model High-speed models: CS1H-CPU67-E, CS1H-CPU66-E, CS1H-CPU65-E, CS1H-CPU64-E, and CS1H-CPU63-E Low-speed models: CS1G-CPU45-E, CS1G-CPU44-E, CS1G-CPU43-E, and CS1G-CPU42-E CS1G-CPU44 and CS1G-CPU45 C200HX-CPU34-E/44-E/54-E/64-E/34-ZE/44-ZE/54-ZE/64-ZE/65-ZE/85-ZE C200HG-CPU33-E/43-E/53-E/63-E/33-ZE/43-ZE/53-ZE/63-ZE C200HE-CPU32-E/42-E/32-ZE/42-ZE CQM1H-CPU51 and CQM1H-CPU61
7-30
Communications
H Peripheral Devices
Name CX-Protocol
Chapter 7
The following peripheral devices are required to use the protocol macro function.
Model WS02-PSTC1-E Specification The following peripheral devices support the protocol macro function of the SYSMAC CS1 Series. Personal computer environment Personal IBM PC/AT or compatible computer computer CPU Minimum requirement: Pentium 90 MHz Recommended: Pentium 166 MHz or faster OS Microsoft Windows 95 or Windows 98 Memory Minimum: 16 MB Recommended: 24 MB min. Hard disk Minimum: Available space of 24 MB Recommended: Available space of 50 MB Monitor SVGA or better Drive FDD: 1 or more CD-ROM drive: 1 or more The following peripheral devices support the protocol macro function of the SYSMAC C200HX/HG/HE. Personal computer environment Personal IBM PC/AT or compatible computer computer CPU Minimum requirement: Pentium 90 MHz Recommended: Pentium 166 MHz or faster OS Microsoft Windows 95 or Windows 98 Memory Minimum: 16 MB Recommended: 24 MB min. Hard disk Minimum: Available space of 24 MB Recommended: Available space of 50 MB Monitor SVGA or better Drive FDD: 1 or more CD-ROM drive: 1 or more
WS01-PSTF1-E
7-31
Communications
H Manuals
Chapter 7
Refer to the following manuals for the peripheral devices and support software in detail.
Product SYSMAC CS-series Programmable Controllers SYSMAC CJ-series Programmable Controllers SYSMAC C200HX/HG/HE Programmable Controllers SYSMAC CQM1H Programmable Controllers and Inner Boards CS1W-SCB21/41 Serial Communications Boards CS1W-SCU21/41 Serial Communications Units C200HW-COM06-EV1 Communications Board WS02-PSTC1-E CX-Protocol WS01-PSTF1-E Protocol Support Tool Catalog No. Operation Manual: W339 Programming Manual: W340 Operation Manual: W393 Programming Manual: W394 Installation Manual: W302 Operation Manual: W303 Operation Manual: W363 Programming Manual: W364 W336 W304 W344 W319
H Communications Boards
Communications Boards are required for communications via the RS-422/485 port. The Communications Boards that can be used are listed below. Note The RS-232C port can be used if an RS-422/485 conversion adapter is installed. For ease of wiring, however, it is recommended that the RS-422/485 port be used. The following information is for the RS-422/485 port.
Series SYSMAC CS Series Communications Board model CS1W-SCB41 Mounting method As an inner board of the CPU Unit Specifications One RS-232C port One RS-422/485 port Protocol macro function One RS-232C port One RS-422/485 port Protocol macro function One RS-232C port One RS-422/485 port Protocol macro function As an inner board of the CPU Unit One RS-232C port One RS-422/485 port Protocol macro function
SYSMAC CJ Series
CJ1W-SCU41
SYSMAC C200HX/HG/HE
SYSMAC CQM1H
C200HW-COM06-EV1 Note Make sure that the model number has the suffix EV1, otherwise the CRC-16 check code cannot be used. CQM1H-SCB41 (Used on CQM1H-CPU51/61.)
7-32
Communications
H Settings for Serial Communications Boards and Units
Chapter 7
The settings required in the Setup Area/PC Setup for Serial Communications Boards and Units are shown in the following tables.
CS/CJ Series
Use the following ports for CS/CJ-series Communications Boards and Units: S Port 2 of the CS1W-SCB41 Serial Communications Board S Port 2 of the CJ1W-SCU41 Serial Communications Unit m = D30000 + 100 unit number
DM Area Board Port 1 Port 2 D32000 D32010 Unit Port 1 m Port 2 m+10 15 Port settings 0: Default settings 1*: User settings Reserved Serial communications mode (6 Hex*: Protocol macro) Reserved Start bits 0*: 1 bit; 1: 1 bit (1 start bit is always used regardless of this setting) Data length 0: 7 bits; 1*: 8 bits Stop bits 0: 2 bits; 1*: 1 bit Parity 0: Yes; 1*: No Parity 0*: Even; 1: Odd Reserved Baud rate (unit: bps) 0: Default (9,600); 3: 1,200; 4: 2,400; 5: 4,800; 6*: 9,600; 7: 19,200; 8: 38,400 Transmission method 0: Half duplex; 1*: Full duplex Reserved Maximum number of bytes in protocol macro send/receive data: 00C8* to 03E8 (Hex) 860E Bit Meaning g Setting g
12 to 14 08 to 11 05 to 07 04
0006
D32008
D32018
m+8
m+18
15 00 to 14 00 to 15
8000
D32009
D32019
m+9
m+19
00C8
Note Use the settings marked with an asterisk in the above table.
7-33
Communications
Communications Board Port 1 Port 2 Port A Port B DM 6555 DM 6550 Bit Meaning
Chapter 7
Setting
00 to 03
04 to 11 12 to 15
DM 6556
DM 6551
00 to 07
08 to 15
6001 Port settings 0 Hex: Standard settings (default setting) 1 Hex*: Settings in DM 6556/6551 00: Default setting Serial communications mode 0 Hex: Host Link (default setting); 1 Hex: No-protocol; 2 Hex: 1:1 Data Link slave; 3 Hex: 1:1 Data Link master; 4 Hex: NT Link in 1:1 mode; 5 Hex: NT LInk in 1:N mode; 6 Hex*: Protocol macro 0803 Baud rate (unit: bps) 00 Hex: 1,200 (default setting); 01 Hex: 2,400; 02 Hex: 4,800: 03 Hex*: 9,600; 04 Hex: 19,200 Frame format: Setting Start bit Data Stop Parity length bits 00 Hex 1 7 1 Even (default setting) 01 Hex 1 7 1 Odd 02 Hex 1 7 1 None 03 Hex 1 7 2 Even 04 Hex 1 7 2 Odd 05 Hex 1 7 2 None 06 Hex 1 8 1 Even 07 Hex 1 8 1 Odd 08 Hex* 1 8 1 None 09 Hex 1 8 2 Even 10 Hex 1 8 2 Odd 11 Hex 1 8 2 None
Note Use the settings marked with an asterisk in the above table.
7-34
Chapter 7
RS-422 /485 Interface Frame 9-pin, D-sub connector (Cable side: Male)
3G3JV Code
Control circuit terminal block (communications terminals)
7-35
Communications
D RS-485 (4-wire)
Communications Board
Code Pin No.
Chapter 7
RS-422/ 485 Interface Frame 9-pin, D-sub connector (Cable side: Male)
Note Be sure to set the terminal resistance of only the Inverter at each end to ON and that of any other Inverter to OFF. Refer to 7-1-3 Names of Parts for details.
D RS-422 (4-wire)
Communications Board
Code Pin No.
shield
1 SDA RS-422/ 2 SDB 485 6 RDA Interface RDB 8 FG Frame 9-pin, D-sub connector (Cable side: Male)
Note Be sure to set the terminal resistance of only the Inverter at each end to ON and that of any other Inverter to OFF. Refer to 7-1-3 Names of Parts for details.
7-36
Communications
Chapter 7
S Message: A DSR message or response. S DSR Message: A message sent by the Master for instructions to the Inverter. S Response: A message that the Inverter returns in compliance with a DSR message from the Master.
D Creating a Message
The message can be created according to the communications specifications of the general-purpose peripheral device (Inverter) as a counterpart. A DSR message can include variables to set data in the I/O memory (such as data memory) of the CPU Unit or write response data to the I/O memory. Each component of a message is in the memory of the Communications Board. Therefore, the CPU Unit can just execute the PMCR instruction to send or receive the data. Therefore, there is no need to write ladder programs for the communications protocol.
CPU Unit Communications Board DSR message
PMCR instruction Send
3G3JV
Reception
Response
Sending and receiving messages as a single step includes step-type commands, such as Send, Recv, Send & Recv, and Wait commands. The step can be finished or switched to another step according to the result of the step.
CPU Unit Communications Board 3G3JV
PMCR instruction
Step 0
The protocol consists of one or more sequences. A sequence is an independent set of actions to perform together with a general-purpose peripheral device, such as an Inverter. The RUN command and the frequency reference are given to the Inverter and the status of the Inverter is read in a single sequence, for example. A sequence consists of one or more steps.
7-37
Communications
D Sequence
Chapter 7
When repeating actions to give the RUN command and frequency reference to the Inverter and read the status of the Inverter, for example, the actions can be registered as one sequence, or more than one if necessary. In 7-10-4 Creating a Project File, an example is shown with all actions registered as a single sequence. A sequence may include the following parameters.
Parameter Transmission control parameter Link word Description Set the method of control, such as flow control. Note Select only model control for communications with the 3G3JV. Set the area for sharing the data between the Programmable Controller and Communications Board. Note In 7-10-4 Creating a Project File, an example is shown without such an area set. Set the periods to monitor the transmission and reception steps with timers Tr, Tfr, and Tfs. Note Set a period of approximately 0.5 s each for communications with the 3G3JV. A method to write reception data to the I/O memory of the Programmable Controller. Note Select notify by scan for communications with the 3G3JV.
Communications Board CPU Unit Step 00
PMCR instruction DSR message (Write the RUN command and frequency reference.)
Monitor time
3G3JV
Sequence 000
7-38
Communications
D Step
Chapter 7
In a single step, a DSR message is sent and a response for the DSR message is received. A step may not include a response if it is a broadcast message. In the case of repetitive actions to issue the RUN command and frequency reference to the Inverter and read the status of the Inverter, for example, the actions to give the RUN command and frequency reference is one step. The reason is that these register numbers are consecutive and can be sent with a single DSR message. The action to read the status of the Inverter is another step.
A step includes a command and a maximum of two messages. The above example uses the Send & Recv command. The DSR message and response are both messages. A step may include the following parameters.
Description The Send, Send & Recv, Wait, Flush, Open (ER-ON), or Close (ER-OFF) command is set. Note In 7-10-4 Creating a Project File, an example is shown with the Send & Recv command used. The Send command is used for a broadcast message. Message g Send message A DSR message is set for the Send command used. Recv message A response is set for the Recv command. Send & Recv message A DSR message and response are set for the Send & Recv command. Recv matrix If there are two or more responses for the Send or Send & Recv command, the next process is selected per response. Repeat counter The number (N) of times to repeat the step is set within a range from 0 to 255. It is possible to change messages by making use of the number (N). Note In 7-10-4 Creating a Project File, an example is shown with this function used for enabling three Slaves to repeat the same process. Number of retries The number of times to retry the command can be set within a range from 0 to 9 only when the Send & Recv command is used. Note It is recommended that the number be set to 3 or larger. Send Wait Time The waiting time until data is sent with the Send or Send & Recv command executed. Response Write (with operand specified) Determines whether or not to write the reception data in the response. Note In 7-10-4 Creating a Project File, an example is shown with this function used for writing the Inverter status to the memory. Next process Determines which step is to be processed next or finishes the operation after the step is finished normally. Error processing Determines which step is to be processed next or finishes the operation, if the step has an error. Command Parameter
7-39
Communications
H Data Created by Protocol Support Tool
A project file is used by the Protocol Support Tool to create and control data. A project file consists of the following data.
Single project file Protocol list Protocol name Protocol name Protocol name Trace list PLC Protocol name (Single protocol) Sequence 000/Sequence name Sequence 001/Sequence name Sequence 999/Sequence name Send message list
Chapter 7
A maximum of 60 sequences/protocol The first sequence number and last sequence number are specified by each protocol. Message name Message name
Recv matrix
Sequence #jjj
Note The standard system protocol incorporated by the Communications Board cannot be edited or transferred. To make use of the standard system protocol, copy it to the project file and edit it. In 7-10-4 Creating a Project File, an example to create a new project file is shown without making use of the standard system protocol.
H Design
Select from I/O items, monitor items, and parameters the data to be exchanged according to the application. Then consider what sequence is required by using the protocol macro function. Example: Writes control input items (such as the RUN command and multi-function input) of the Inverter and frequency reference, monitors the control output (such as error output and RUN out-
7-40
Communications
Chapter 7
put) of the Inverter, and monitors the Inverter status. Three Inverters with Slave addresses from 01 to 03 are installed for communications.
D Memory Allocations
The PMCR instruction sends each Slave the data in consecutive words specified by the operand and beginning with the first word (S), and writes in the memory area beginning with the first word (D) the data received. The following memory allocations are made in the above example.
Communications Board/Unit
3G3JV
Sequence No. 0000 to 03E7 Hex (000 to 999) Data Protocol macro function
No. of data items sent in accordance with PMCR instruction (000B)
No. of Slaves (0003) First Slave address (0001) RUN command to Slave 1 Frequency reference to Slave 1 Second Slave address (0002) RUN command to Slave 2 Frequency reference to Slave 2 Third Slave address (0003) RUN command to Slave 3 Frequency reference to Slave 3
No. of data items received in accordance with PMCR instruction (0003)
7-41
Communications
SYSMAC C200HX/HG/HE or CQM1H Programmable Controllers C: Control data
Chapter 7
Communications Board 3G3JV
No. of Slaves (0003) First Slave address (0001) RUN command to Slave 1 Frequency reference to Slave 1 Second Slave address (0002) RUN command to Slave 2 Frequency reference to Slave 2 Third Slave address (0003) RUN command to Slave 3 Frequency reference to Slave 3
No. of data items received in accordance with PMCR instruction (0003)
H Creating a Sequence
1. Click on New Protocol with the left button of the mouse. Then click on a blank space with the right button of the mouse. 2. Select Create communication Sequence. The following table will appear. Set the parameters related to the sequence in the table.
7-42
Communications
* # CommunicaLink word tion sequence Inverter I/O --Send & Recv Control Response Timer Tr
Chapter 7
Timer Tfr 0.5 Timer Tfs 0.5
000
Scan
0.5
#
Sequence number. The sequence number is automatically set.
Communication Sequence
The label (name) of the sequence. Input an appropriate, easy-to-distinguish name.
Link Word
Set the area for sharing the data between the Programmable Controller and Communications Board. Note In this example, the link word is specified by the operand of the PMCR instruction. Therefore, no link word is set here.
Control
Set the control method, such as flow control. Note Select only model control for communications with the 3G3JV.
Response
A method to write reception data to the I/O memory of the Programmable Controller. Note Select notify by scan for communications with the 3G3JV.
7-43
Communications
Ts: Send wait time set per step. Nothing is sent during this period.
Chapter 7
Tfs: Monitors the completion of the data sent. If the data transmission is not finished within this period, the data will be re-transmitted. Tr: Monitors the response to be received. If the response is not returned within this period, the response will be re-transmitted. Tfr: Monitors the reception completion of the response. If the response transmission is not finished within this period, the response will be re-transmitted. Note If the Tr period is too long, the time required to detect a communications error will be longer, during which the Inverter cannot be controlled. Therefore, be sure to set an appropriate period.
H Creating a Step
1. Double-click on New Protocol with the left button of the mouse. 2. Click on New Sequence with the left button of the mouse and click on a blank space with the right button of the mouse. 3. Select Create Step. The following table will appear. Set the parameters related to the step in the table.
* Step Repeat Command Send & Receive Send & Receive 3 3 Retry Send wait ----Send message Input send Status Recv message Response Next Error
j 00 j 01 j
Next End
Abort Abort
Step
Step number. The step number is automatically set.
Repeat
The number (N) of times to repeat the step is set within a range from 0 to 255. It is possible to change messages by making use of the number (N). Note In this example, the same message is sent to three Slaves with addresses different to each other. Therefore, the number is set to 3 in word S + 1. The number of Slaves is specified by the operand. Therefore, select Channel, use the Edit command to set Data Address to Operand, and set 0N + 1 in order to select word S + 1. In the above table, Reset means that the repeat counter must be reset first in the step.
Command
Set the commands, such as Send, Recv, and Send & Recv. Note Only the Send & Recv command is used for communications with the 3G3JV except for sending broadcast messages, in which case the Send & Receive command is used.
Retry
Set the number of times to retry the command within a range from 0 to 9.
7-44
Communications
Chapter 7
Note It is recommended that the number be set to 3 or larger. If a transmission error occurs due to noise, the transmission of the command will be retried. If the number is set to 3, an error will be detected if the transmission fails three times.
Send Wait
The waiting time until the data is sent. Note For communications with the 3G3JV, if data is repeatedly transmitted to the same Slave, set the waiting time to 20 ms or more. In this example, the DSR message is sent to Slaves 1, 2, and 3 one by one. Therefore, no send wait time is set.
Response
Determine whether or not to write the reception data in the response. Note Always set this parameter to Yes for communications with 3G3JV.
Next
Determine which step is to be processed next or finish the operation after the step finishes normally. Note In this example, step 00 is set to Next and step 01 is set to END because the sequence completes by executing steps 00 and 01.
Error
If the step has an error, determine which step is to be processed next or finish the operation. Note In this example, the parameter will be set to Abort to interrupt the sequence if an error occurs.
Data
j Status
(3N+2), 1) <a> + [10] + [00] + [01] + [00] + [02] + <I> (R (3N + 3), 4) + <c> ~(R (3N+2), 1) <a> + [03] + [00] + [2C] + [00] + [01] + <c>
7-45
Communications
Message Name
The label (name) of the sequence. Input an appropriate, easy-to-distinguish name.
Chapter 7
Note Set the label in the send message box in the table shown under Creating a Step.
Length <l>
Set the length of the data. Note All communications with the 3G3JV are performed in byte units. Select 1 Byte and BIN. Select No for reading data because there is no data to be read.
Address <a>
Set the addresses of the Slaves. Note In this example, the Slave addresses are set in S + 2, S + 5, and S + 8. Therefore, retrieve the data from those locations. The address is set in the LSB of each word. To read the byte, select Variable Reverse, otherwise the data is read from the LSB. Then click on Edit Variable with the left button of the mouse. Select Read R () and set Data/Address to the operand (3N + 2) using the number (N) of times to repeat the step. Set Edit Length to 1 byte as a default. If the default value has been changed, set it to 0N + 1.
Data
Set the DSR message in details. DSR Message Requesting that the RUN Command and Frequency Reference be Written The DSR message to write data to two registers from register 0001 Hex (the RUN command) consists of the following items.
CRC-16 check (Set with <c>) Next register data Set with variables Start register data Number of bytes of attached data (set with <l>) Number of write data registers: 2 Write start register number (RUN command: 0001) Function code (Write 10) Slave address (Set with <a>)
7-46
Communications
Set data: <a> + [10] + [00] + [01] + [00] + [02] + <I> + (R (3N + 3), 4) + <c>
Chapter 7
<a> The Slave address is set in the address box. Insert the address with the Insert icon. [10] + [00] + [01] + [00] + [02] Set the constants contained in the DSR message. Use Set Constant and set the constants in Hex. <I> The length is set in the length box. Insert the length by using the Insert icon. The length is the number of bytes of the succeeding data (R(3N + 3), 4). The length is automatically set by the CX-Protocol. (R(3N+3), 4) The Inverters actual data to be sent. This example selects Variable and Read R() and sets the operand. Set Data to 3N + 3 because the RUN command data uses four bytes each from S + 3, S + 6, and S + 9. Set Edit Length to 0N + 4 so that it will be set to four bytes. <c> The check code is set in the check code box. Insert the check code by using the Insert icon. All the data including the address data before the check code is operated. Mark all the items if the Protocol Support Tool is used. The check code is automatically set by the CX-Protocol. DSR Message to Read the Inverter Status The DSR message to read the Inverter status from register 002C Hex consists of the following items.
CRC-16 check (Set with <c>) Number of read data registers: 1 Read start register number (Inverter status: 002C) Function code (Read 03) Slave address (Set with <a>)
Set data: <a> + [03] + [00] + [2C] + [00] + [01] + <c> Set the address data, constant data, and check code data.
Data <a> + [10] + [00] + [01] + [00] + [02] + <c> <a> + [03] + <I> + (W (1N + 1), 2) + <c>
(3N+2),
1)
7-47
Communications
Message
The label (name) of the response. Input an appropriate, easy-to-distinguish name.
Chapter 7
Note Set the label in the Recv message box in the table shown under Creating a Step.
Length <l>
Set the length of the data. Note All communications with the 3G3JV are performed in byte units. Select 1 Byte and BIN. Select No for reading data because there is no data to be read.
Address <a>
Set the addresses of the Slaves. Note In this example, the Slave addresses are set in S + 2, S + 5, and S + 8. Therefore, retrieve the data from those locations. The address is set in the LSB of each word. To read the byte, select Variable Reverse, otherwise the data will be read from the LSB. Then click on Edit Variable with the left button of the mouse. Select Read R () and set Data/Address to the operand (3N + 2) using the number (N) of times to repeat the step. Set Edit Length to 1 byte as a default. If the default value has been changed, set it to 0N + 1.
Data
Set the expected response in details. Response to the RUN Command and Frequency Reference The response to the DSR message written consists of the following items.
CRC-16 check (Set with <c>) Number of write data registers: 2 Write start register number (RUN command: 0001) Function code (Write 10) Slave address (Set with <a>)
7-48
Communications
Chapter 7
<a> The Slave address is set in the address box. Insert the address with the Insert icon. [10] + [00] + [01] + [00] + [02] Set the constants contained in the response. Use Set Constant and set the constants in Hex. <c> The check code is set in the check code box. Insert the check code by using the Insert icon. All the data including the address data before the check code is used. Mark all the items if the Protocol Support Tool is used. The check code is automatically set by the CX-Protocol. Response to the Inverter Status Read The response to the DSR message to request the Inverter status in register 002C Hex consists of the following items.
CRC-16 check (Set with <c>) Inverter status data (Set with variable) Number of bytes of attached data (set with <l>) Function code (Write 10) Slave address (Set with <a>)
Set data: <a> + [03] + <I> + (W (1N + 1), 2) + <c> <a., [03], <c> The address data, constant data, and check code data are the same as the above. <l> The length is set in the length box. Insert the length by using the Insert icon. The length is the number of bytes of the succeeding data (W(1N + 1), 2). The length is automatically set by the CX-Protocol. (W(1N + 1), 2) The Inverters actual data is to be sent. This example selects Variable and Read R() and sets the operand. Set Data to 1N + 1 because the RUN command data uses four bytes each from D + 3, D + 6, and D + 9. Set Edit Length to 0N + 2 so that it will be set to two bytes.
7-49
Chapter 7
Before using this program in your system, be sure to check the word and data memory allocations and change them if necessary so that there will be no word or data memory duplication. This program will stop all communications if a communications error or fault occurs. Be sure to set n68 for communications time-over detection selection to 0 through 2 so that the system will stop with timeover detection.
H Memory Allocations
D Starting Communications and Status Signals
Word 000000 000001 000002 Functions common to all Slaves Inverter control communications (continued when set to ON) Communications error output (on hold when a communications error or fault occurs) Communications fault reset
7-50
Communications
D Inverter Control Output (Register 002C Inverter Status)
Word 001100 001101 001102 001103 001104 001105 001106 001107 001108 001109 001110 001111 001112 001113 001114 001115 Slave 1 function During RUN Zero speed Frequency agree Warning (Nonfatal error) Frequency detection 1 Frequency detection 2 Inverter ready UV Base block Frequency reference mode RUN command mode Overtorque detection 0 (Not used.) Fault retry Fault Communications timeover Word 001200 001201 001202 001203 001204 001205 001206 001207 001208 001209 001210 001211 001212 001213 001214 001215 Slave 2 function During RUN Zero speed Frequency agree Warning (Nonfatal error) Frequency detection 1 Frequency detection 2 Inverter ready UV Base block Frequency reference mode RUN command mode Overtorque detection 0 (Not used.) Fault retry Fault Communications timeover Word 001300 001301 001302 001303 001304 001305 001306 001307 001308 001309 001310 001311 001312 001313 001314 001315
Chapter 7
Slave 3 function During RUN Zero speed Frequency agree Warning (Nonfatal error) Frequency detection 1 Frequency detection 2 Inverter ready UV Base block Frequency reference mode RUN command mode Overtorque detection 0 (Not used.) Fault retry Fault Communications timeover
Control Data: C2
Area
7-51
Communications
Send Data: S
DM D01000 D01001 D01002 D01003 D01004 D01005 D01006 D01007 D01008 D01009 D01010 Area 000B (Number of send data items: 11) (See note 1.) 0003 (Number of Slaves) 0001 (Slave 1 address) RUN command to Slave 1 Frequency reference to Slave 1 0002 (Slave 2 address) RUN command to Slave 2 Frequency reference to Slave 2 0003 (Slave 3 address) RUN command to Slave 3 Frequency reference to Slave 3
Chapter 7
Recv data: D
DM D02000 D02001 D02002 D02003 Area 0003 (Number of Recv data items: 3) (See note 2.) Slave 1 Inverter status Slave 2 Inverter status Slave 3 Inverter status
Note 1. Set the number of send data items in Hex to the number of words from D01000 to D01010 (11). Note 2. The number of words from D02001 to D02003 (3) is written in Hex in the number of Recv data items.
D Status Flags
Communications Port Enabled Flags If communications port 7 is selected: A20207 Protocol Macro Execution Flag The address of the Protocol Macro Execution Flag is as follows:
Model CS1 Communications Board CS1 Communications Unit Port 1 190915 Bit 15 of word n+9 (See note.) Port 2 191915 Bit 15 of word n+19 (See note.)
Note n = 1500 + 25 unit number Communications Port Abort Flag The address of the Communications Port Abort Flag is as follows:
Model CS1 Communications Board CS1 Communications Unit Port 1 190913 Bit 13 of word n+9 (See note.) Port 2 191913 Bit 13 of word n+10 (See note.)
7-52
Communications
H Ladder Program
Chapter 7
D00100
Note The Communications Port Enabled Flag will be required if the SYSMAC CS Series is used.
0002
7-53
Chapter 7
The communications response times for communications with an Inverter via the RS-422/485 port of an OMRON-made Communications Board are detailed below. Use this information as a reference when deciding the number of Slaves to be connected to one network, and when considering the timing of input and output signals.
A wide variety of programs for RS-422/485 communications can be created using the protocol macro function. The communications times will vary according to the contents of the program. In general, the communications time for one message can be calculated using the following formula. Communications time = [Number of bytes in DSR message 10 (See note 1.) (1/baud rate) 1,000 (ms)] + [Number of bytes in response 10 (1/baud rate) 1,000 (ms)] + [24 (1/baud rate) 1,000 (ms)] + send wait time setting n73 (ms) + protocol macro waiting time (See note 2.) (ms) Note 1. The reason that the number of bytes in the DSR message and response is multiplied by 10 is because both the start bit and the stop bit require one bit each. (1 byte = 8 bits) + (start bit: 1 bit) + (stop bit: 1 bit) = 10 bits Note 2. With RS-422/485 communications, set at least 20 ms as the protocol macro waiting time.
D Calculation Example
The communications time required for one Slave in the protocol macro created in 7-10-4 Creating a Project File, can be calculated according to the following formula. (Baud rate = 19,200 bps.) Communications time = [(DSR message to write data (13 bytes) + DSR message to read (8 bytes)) 10 (1/19,200) 1,000 (ms)] + [(write response (8 bytes) + read response (7 bytes)) 10 (1/19,200) 1,000 (ms)] + [24 (1/19,200) 1,000 (ms) 2] + [10 (ms) 2] + [20 (ms) 2] = 81.2 (ms) Note If there are N Slaves, the total communications time will be N 81.2 ms. Consequently, the more Slaves that are used, the longer the communications time will be. If the number of Slaves is too high, it is possible that the detection time of 2 s for communications time-over will be exceeded. In this case, either disable the time-over detection function and use a different sequence to detect communications errors, or increase the number of Masters thereby decreasing the number of Slaves per Master.
The communications processing times for the Inverter are as follows. S Inverter communications input scan: 8 ms S Inverter communications output scan: 8 ms S Internal processing time for the Inverter: Approx. 20 ms The I/O response times for the Inverter are illustrated in the following diagram.
Ladder program cycle time Communications time 2 Inverter I/O scan Internal processing for the Inverter
7-54
8
Chapter 8 Maintenance Operations
8-1 8-2 8-3 Protective and Diagnostic Functions Troubleshooting Maintenance and Inspection
Chapter 8
8-2
Maintenance Operations
Fault display uU1 Fault name and meaning Probable cause and remedy
Chapter 8
Main circuit undervoltage Power supply to the Inverter has phase loss, power input (UV1) terminal screws are loose, or the power cable is disconnected. The main circuit DC voltage has reached the undervoltage Check the above and take necessary countermeasures. detection level (200 V DC for the 3G3JV-A2j, 160 V DC for Incorrect power supply voltage Make sure that the power supply voltage is within the 3G3JV-ABj, and 400 V specifications. DC for the 3G3JV-A4j). Momentary power interruption has occurred. Use the momentary power interruption compensation (Set n47 so that the Inverter restarts after power is restored) Improve the power supply. The internal circuitry of the Inverter is damaged.
%h
Radiation fin overheated (OH) The temperature of the radiation fins of the Inverter has reached 110_C 10_C.
Change the Inverter. The ambient temperature is too high. Ventilate the Inverter or install a cooling unit. The load is excessive. Reduce the load. Decrease the Inverter capacity. The V/f setting is incorrect. Reduce the V/f set voltage. The acceleration/deceleration time is too short. Increase the acceleration/deceleration time. The ventilation is obstructed. Change the location of the Inverter to meet the installation conditions. The cooling fan of the Inverter does not work. Replace the cooling fan.
8-3
Maintenance Operations
Fault display %l1 Fault name and meaning Motor overload (OL1) The electric thermal relay actuated the motor overload protective function. Probable cause and remedy The load is excessive. Reduce the load. Decrease the Inverter capacity. The V/f setting is incorrect.
Chapter 8
Reduce the V/f set voltage. The value in n11 for maximum voltage frequency is low. Check the motor nameplate and set n11 to the rated frequency. The acceleration/deceleration time is too short. Increase the acceleration/deceleration time. The value in n32 for rated motor current is incorrect. Check the motor nameplate and set n32 to the rated current. The Inverter is driving more than one motor. Disable the motor overload detection function and install an electronic thermal relay for each of the motors. The motor overload detection function is disabled by setting n32 to 0.0 or n33 to 2. The motor protective time setting in n34 is short. %l2 Inverter overload (OL2) The electronic thermal relay has actuated the Inverter overload protective function. Set n34 to 8 (the default value). The load is excessive. Reduce the load. The V/f setting is incorrect. Reduce the V/f set voltage. The acceleration/deceleration time is too short. Increase the acceleration/deceleration time. The Inverter capacity is insufficient. %l3 Overtorque detection (OL3) There has been a current or Check the mechanical system and correct the cause of torque the same as or greater overtorque. than the setting in n60 for The parameter settings were incorrect. overtorque detection level and Adjust the n60 and n61 parameters according to the that in n61 for overtorque mechanical system. detection time. A fault has Increase the set values in n60 and n61. been detected with n59 for overtorque detection function selection set to 2 or 4. Ground fault (GF) A ground fault has occurred at the Inverter output. The ground fault current at the Check the connections between the Inverter and motor output of the Inverter has and reset the fault after correcting its cause. exceeded the rated output current of the Inverter. Use an Inverter model with a higher capacity. The mechanical system is locked or has a failure.
gf
8-4
Maintenance Operations
Fault display efj Fault name and meaning External fault j (EFj) An external fault has been input from a multi-function input. A multi-function input 1, 2, 3, or 4 set to 3 or 4 has operated. The EF number indicates the number of the corresponding input (S2 to S5). Digital Operator transmission fault 1 (F00) An initial memory fault has been detected Digital Operator transmission fault 2 (F01) A ROM fault has been detected. Initial memory fault (F04) An error in the built-in EEPROM of the Inverter has been detected. Analog-to-digital converter fault (F05) An analog-to-digital converter fault has been detected. Digital Operator fault (F07) An error in the built-in control circuit of the Digital Operator has been detected. Probable cause and remedy
Chapter 8
An external fault was input from a multi-function input. Remove the cause of the external fault. The sequence is incorrect. Check and change the external fault input sequence including the input timing and NO or NC contact.
f00
The internal circuitry of the Inverter has a fault. Turn the Inverter off and on. Replace the Inverter if the same fault occurs again. The internal circuitry of the Inverter has a fault. Turn the Inverter off and on. Replace the Inverter if the same fault occurs again. The internal circuitry of the Inverter has a fault. Initialize the Inverter with n01 set to 8 or 9 and turn the Inverter off and on. Replace the Inverter if the same fault occurs again. The internal circuitry of the Inverter has a fault. Turn the Inverter off and on. Replace the Inverter if the same fault occurs again. The internal circuitry of the Digital Operator has a fault. Turn the Digital Operator off and on. Replace the Digital Operator if the same fault occurs again.
f01
f04
f05
f07
ce
Communications time-over A short-circuit, ground fault, or disconnection has occurred (CE) on the communications line. Normal RS-422/485 Check and correct the line. communications were not The termination resistance setting is incorrect. established within 2 s. The Set the termination resistance of only the Inverter located Inverter will detect this error if at each end of the network to ON. n68 (RS-422/485 communications time-over Noise influence. detection selection) is set to 0, Do not wire the communications line along with power 1, or 2. lines in the same conduit. Use the twisted-pair shielded wire for the communications line, and ground it at the Master. Masters program error. Check and correct the program so that communications will be performed more than once every 2-s period. Communications circuit damage. If the same error is detected as a result of a self-diagnostic test, change the Inverter.
8-5
Maintenance Operations
Fault display Fault name and meaning Emergency stop (STP) An emergency stop alarm is input to a multi-function input. (A multi-function input 1, 2, 3, or 4 set to 19 or 21 has operated.) Power supply error Insufficient power supply voltage Control power supply fault Hardware fault Probable cause and remedy
Chapter 8
An emergency stop alarm is input to a multi-function input. Remove the cause of the fault. The sequence is incorrect. Check and change the external fault input sequence including the input timing and NO or NC contact. No power supply is provided. Check and correct the power supply wire and voltage. Terminal screws are loosened. Check and tighten the terminal screws. The Inverter is damaged. Replace the Inverter.
OFF
8-6
Chapter 8
The warning detection is a type of Inverter protective function that does not operate the fault contact output and returns the Inverter to its original status once the cause of the error has been removed. The Digital Operator flashes and display the detail of the error. If a warning occurs, take appropriate countermeasures according to the table below. Note Some warnings or some cases stop the operation of the Inverter as described in the table.
%U (flashing)
%h (flashing)
cal (flashing)
Main Circuit Overvoltage The main circuit DC voltage has reached the overvoltage detection level (200-V models: 410 V DC min.; 400-V models: 820 V DC min.). Radiation fin overheated (OH) The temperature of the radiation fins of the Inverter has reached 110_C 10_C. Communications standby (CAL) No normal DSR message has been received during RS-422/4895 communications. The Inverter detects this warning only when RUN command selection (n02) is set to 2 or frequency reference selection (n03) is set to 6. Until the warning is reset, no input other than communications input will be ignored.
%l3 (flashing)
Overtorque detection (OL3) There has been a current or torque the Check the mechanical system and correct the same as or greater than the setting in cause of overtorque. n60 for overtorque detection level and The parameter settings were incorrect. that in n61 for overtorque detection Adjust the n60 and n61 parameters according time. A fault has been detected with to the mechanical system. n59 for overtorque detection function Increase the set values in n60 and n61. selection set to 1 or 3.
8-7
Maintenance Operations
Chapter 8
Fault display Warning name and Meaning Probable cause and remedy Sequence error (SER) A sequence error has occurred. ser (flashing) A sequence change has been input Check and adjust the local or remote while the Inverter is in operation. selection sequence as multi-function input. Local or remote selection is input while the Inverter is in operation. Note The Inverter coasts to a stop. External base block (bb) The external base block command has been inbb (flashing) put as multi-function input. The external base block command has been input. Remove the cause of external base block Note The Inverter coasts to a stop. input. The sequence is incorrect. Check and change the external fault input sequence including the input timing and NO or NC contact. A sequence error has occurred.
ef (flashing)
(flashing)
fRn (flashing)
Forward- and reverse-rotation input (EF) Check and adjust the local or remote The forward and reverse commands selection sequence. are input to the control circuit terminals simultaneously for 0.5 s or more. Note The Inverter stops according to the method set in n04. Emergency stop (STP) The parameter setting was incorrect. The Digital Operator stops operating. Turn off the forward or reverse command once, check that the n06 parameter setting for The STOP/RESET Key on the Digital STOP/RESET Key function selection, and Operator is pressed while the Inverter restart the Inverter. is operating according to the forward or reverse command through the control circuit terminals. Note The Inverter stops according to the method set in n04. The emergency stop alarm signal is An emergency stop alarm is input to a multi-funcinput as multi-function input. tion input. A multi-function input 1, 2, 3, or 4 set Remove the cause of the fault. to 20 or 22 has been used. The sequence is incorrect. Note The Inverter stops according to Check and change the external fault input the method set in n04. sequence including the input timing and NO or NC contact. Cooling fan fault (FAN) The cooling fan wiring has a fault. The cooling fan has been locked. Turn off the Inverter, dismount the fan, and check and repair the wiring. The cooling fan in not in good condition. Check and remove the foreign material or dust on the fan. The cooling fan is beyond repair. Replace the fan.
8-8
Maintenance Operations
Fault display Warning name and Meaning Communications time-over (CE) ce Normal RS-422/485 communications were not established within 2 s. The Inverter will detect this error if n68 (RS-422/485 communications time-over detection selection) is set to 0, 1, or 2.
Chapter 8
Probable cause and remedy A short-circuit, ground fault, or disconnection has occurred on the communications line. Check and correct the line. The termination resistance setting is incorrect. Set the termination resistance of only the Inverter located at each end of the network to ON. Noise influence. Do not wire the communications line along with power lines in the same conduit. Use the twisted-pair shielded wire for the communications line, and ground it at the Master. Masters program error. Check and correct the program so that communications will be performed more than once every 2-s period. Communications circuit damage. If the same error is detected as a result of a self-diagnostic test, change the Inverter. The values in n36 through n39 for multi-function inputs 1 through 4 have been duplicated. Check and correct the values. The V/f pattern settings do not satisfy the following condition. n14 x n12 t n11x n09 Check and correct the set value. The rated motor current set in n32 exceeds 150% of the rated output current of the Inverter. Check and correct the value. The frequency reference upper limit set in n30 and the frequency reference lower limit set in n31 do not satisfy the following condition. n30 y n31 Check and correct the set values. The jump frequencies set n49, n50 do not satisfy the following condition. n49 y n50 Check and correct the set values.
%p5 (flashing)
8-9
Chapter 8
Due to parameter setting errors, faulty wiring, and so on, the Inverter and motor may not operate as expected when the system is started up. If that should occur, use this section as a reference and apply the appropriate measures. Refer to 8-1 Protective and Diagnostic Functions, if the contents of the fault are displayed,
8-10
Maintenance Operations
Chapter 8
The frequency reference is too low. If the frequency reference is set below the minimum output frequency set in n14, the Inverter will not operate. Raise the frequency reference to at least the minimum output frequency. The Inverter is in local mode. The Inverter in local mode starts with the RUN command given with the RUN Key pressed. Check the LO/RE indicator. If the display is Lo, the Inverter is in local mode. Press the Increment Key and set the Inverter to remote mode with rE displayed. If the above operation is not possible, a multi-function input is set to local/remote selection. In that case, the mode can be changed with the multi-function input only. Turn the corresponding input terminal OFF so that the Inverter will be set to remote mode. The wiring on the Inverter control circuit terminals is incorrect. The Inverter cannot check input signals if the input wiring on the control circuit terminals is incorrect. Operate the Digital Operator and check the input terminal status of multi-function monitor U06. The NPN or PNP input sequence is selectable. The NPN input sequence is the default setting. Refer to 2-2-2 Terminal Block and check that the setting of switch SW7 and wiring are correct.
H The motor does not operate with input through the control circuit terminals. (The frequency reference is zero or different from the set value.)
The frequency reference setting is incorrect. The analog input of frequency references is ignored with the Digital Operator selected. The digital input of frequency references is ignored unless the Digital Operator is selected. Check that the setting in n03 for frequency reference selection coincides with the actual method of giving frequency instructions. Before using analog input, refer to 2-2-2 Terminal Block and check that the setting of SW8 and the actual method (with voltage and current) of providing frequency references are correct. The Inverter is in local mode. Frequency references can be provided only through key sequences on the Digital Operator or with the FREQ adjuster to the Inverter in local mode. Check the LO/RE indicator. If the display is Lo, the Inverter is in local mode. Press the Increment Key and set the Inverter to remote mode with rE displayed. If the above operation is not possible, the multi-function input will be set to local/remote selection. In that case, the mode can be changed with the multi-function input only. Turn the corresponding input terminal OFF so that the Inverter will be set to remote mode. The analog input gain or bias setting is incorrect. Check that the frequency reference gain in n41 and frequency reference bias in n42 are set according to the actual analog input characteristics.
The load may be too big. The 3G3JV has a stall prevention function and automatic torque boost function, but the motor responsiveness limit may be exceeded if acceleration is too rapid or if the load is too big. Lengthen the acceleration time or reduce the load. Also consider increasing the motor capacity.
8-11
Maintenance Operations
H The motor only rotates in one direction.
Chapter 8
Reverse rotation-prohibit is selected. If n05 for reverse rotation-prohibit selection is set to 1 (reverse run prohibited), the Inverter will not accept reverse-rotation commands. To use both forward and reverse rotation, set n05 to 0.
8-12
Maintenance Operations
The ambient temperature is too high.
Chapter 8
The rating of the motor is determined within a particular ambient operating temperature range. The motor will burn out if it runs continuously at the rated torque in an environment in which the maximum ambient operating temperature is exceeded. Lower the ambient temperature of the motor to within the acceptable ambient operating temperature range. The withstand voltage between the phases of the motor is insufficient. When the motor is connected to the output of the Inverter, a surge will be generated between the switching of the Inverter and the coil of the motor. Normally, the maximum surge voltage is approximately three times the input power supply voltage of the Inverter (i.e., approximately 600 V for 200-V models, and approximately 1,200 V for 400-V models). Therefore, the dielectric strength of the motor to be used must be higher than the maximum surge voltage.
8-13
Chapter 8
Resonance between the characteristic frequency of the mechanical system and the carrier frequency. There may be resonance between the characteristic frequency of the mechanical system and the carrier frequency. If the motor is running with no problems and the machinery system is vibrating with a high-pitched whine, it may indicate that this is occurring. To prevent this type of resonance, adjust the carrier frequency value in n46. Resonance between the characteristic frequency of a machine and the output frequency of the Inverter. There may be resonance between the characteristic frequency of a machine and the output frequency of the Inverter. To prevent this from occurring, use the frequency jump function with the constants set in n49 through n51 to change the output frequency or install vibration-proof rubber on the motor base to prevent the resonance of the mechanical system.
8-14
Maintenance Operations
Chapter 8
8-2-13 Inverter Does Not Run Because EF (Simultaneous Input of Forward and Reverse Commands) is Detected, or Motor Rotates Momentarily While Control Device Power is OFF
Sequence Error An EF will be detected if a forward command and a reverse command are input simultaneously for 0.5 seconds or longer. Correct the sequence. Malfunction Due to Unwanted Current Path Inverter inputs may remain ON due to an unwanted current path for the controller outputs. With the wiring shown in the following table, if the controller output power supply is less than 24 V DC or if the power is OFF, the current indicated by the arrow will flow and the Inverter inputs will operate. If that occurs, insert a diode as shown in the diagram at point A.
Section A Controller (Output unit) Inverter (Control input)
S1 to S5
SC GND
8-15
Chapter 8
WARNING WARNING
WARNING
WARNING
! Caution
! Caution
H Daily Inspection
Check the following items with the system in operation. The motor should not be vibrating or making unusual noises. There should be no abnormal heat generation. The output current value shown on the monitor display should not be higher than normal. The cooling fan on the bottom of the Inverter should be operating normally, if the Inverter model has the cooling fan.
H Periodic Inspection
Check the following items during periodic maintenance. Before beginning inspection, be sure to turn off the power supply. Confirm that all the indicators on the front panel have turned off, and then wait until at least 1 minute has elapsed before beginning the inspection. Be sure not to touch the terminals right after the power has been turned off. Otherwise, an electric shock may occur. The terminal screws of the Inverter should not loose. There should be no conductive dust or oil mist on the terminal block or inside the Inverter. The mounting screws of the Inverter should not be loose.
8-16
Maintenance Operations
No dirt or dust should be accumulating on the radiation fin. No dust should be accumulating on the vents of the Inverter. There should be no abnormalities in the outward appearance of the Inverter.
Chapter 8
There should be no unusual noises or vibration and the accumulated operating time should not exceeded the specifications.
It is recommended that the ambient temperature and power-on time be reduced as much as possible to extend of the life of the Inverter. Note For details regarding maintenance, consult your OMRON representative.
8-17
Maintenance Operations
D Replacing Cooling Fan (68- or 140-mm-wide Inverters)
Chapter 8
1. Press the left and right sides of the fan cover located on the lower part of the radiation fin in the arrow 1 directions. Then lift the bottom of the Fan in the arrow 2 direction to remove the Fan as shown in the following illustration.
2. Hold the fan wire and pull the protective tube of the cover in the arrow 3 direction.
3. Slide the protective tube and remove the internal connector. 4. Remove the Fan from the fan cover. 5. Mount the new Fan on the fan cover. At this time, make sure that the wind direction of the Fan will be in the direction of the heat radiation fin. 6. Attach the connector, cover the connector with the protective tube, and insert the connector into the cover. 7. Mount the fan cover with the new Fan to the lower part of the heat radiation fin. Make sure that the fan cover snaps on securely with the heat radiation fin.
Cooling fan connector (CN4 built in) Wiring groove Heat radiation fin (Heat sink) Fan wind direction
8-18
Maintenance Operations
Chapter 8
2. Press the left and right sides of the fan cover located on the lower part of the radiation fin in the arrow 1 directions. Then lift the bottom of the Fan in the arrow 2 direction to remove the fan as shown in the following illustration. Disconnect the wire from the electrical inlet on the bottom of the plastic casing. 3. Remove the Fan from the fan cover. 4. Mount the new Fan on the fan cover. At this time, make sure that the wind direction of the fan will be in the direction of the heat radiation fin. 5. Mount the fan cover with the new Fan to the lower part of the heat radiation fin. Make sure that the fan cover snaps on securely with the heat radiation fin. 6. Wire the power line through the electrical inlet on the bottom of the plastic casing and the wiring groove into the internal circuitry of the Inverter. 7. Attach the wire to connector CN4 and attach the bottom cover and front cover.
8-19
9
Chapter 9 Specifications
9-1 9-2 9-3 Inverter Specifications Specifications of Accessories Option Specifications
Chapter 9
Model 3G3JVPower Rated voltage and pp y frequency supply Allowable voltage fluctuation Allowable frequency fluctuation Power supply capacity (kVA) (See note 1.) Heat radiation (W) Weight (kg) Cooling method
A2001
A2002
A2004
A2007
A2015
A2022
A2037
0.4
0.9
2.7
4.3
Model 3G3JVPower Rated voltage and pp y frequency supply Allowable voltage fluctuation Allowable frequency fluctuation Power supply capacity (kVA) (See note 1.) Heat radiation (W) (See note 2.) Weight (kg) Cooling method
AB001 AB002 AB004 AB007 AB015 Single-phase 200 to 240 V AC at 50/60 Hz 15% to 10% 5%
---
---
0.5 14.1
0.9 20.0
4.3 82.8
-----
-------
Max. applicable motor capacity (kW) Output p Rated output capacity (kVA) specifiifi Rated output current (A) cations Rated output voltage (V) Max. output frequency Control Harmonic-current characcountermeasures teristics Control method Carrier frequency Frequency control range Frequency precision (temperature characteristics) Frequency setting resolution
0.1 0.2 0.4 0.75 1.5 2.2 3.7 0.3 0.6 1.1 1.9 3.0 4.2 6.7 0.8 1.6 3.0 5.0 8.0 11.0 17.5 3-phase 200 to 240 V AC (according to the input voltage) 400 Hz parameter setting DC reactor (option) connection possible Sine wave PWM (V/f control) 2.5 to 10.0 kHz (in vector control) 0.1 to 400 Hz Digital commands: 0.01% (10C to 50C) Analog commands: 0.5% (25C 10C) Digital commands: 0.1 Hz (less than 100 Hz) and 1 Hz (100 Hz or over) Analog commands: 0.06 Hz/60 Hz (equivalent to 1/1000) 0.01 Hz
9-2
Specifications
Control h characteristics Overload capacity External frequency set signal Acceleration/deceleration time Braking torque
Chapter 9
150% of rated output current for 1 min Selectable with FREQ adjuster: 0 to 10 V DC (20 k), 4 to 20 mA (250 ), and 0 to 20 mA (250 ) 0.0 to 999 s (Independent acceleration and deceleration time settings: 2 types) Approx. 20% (Braking Resistor and Braking Unit cannot be connected.) Set a user V/f pattern Protection by electronic thermal Stops at approx. 250% of rated output current Stops in 1 min at approximately 150% of rated output current Stops when main-circuit DC voltage is approximately 410 V Stops when main-circuit DC voltage is approximately 200 V (160 V for single-phase 200-V AC model) Stops for 15 ms or more. By setting the Inverter to momentary power interruption mode, operation can be continued if power is restored within approximately 0.5 s. Detects at 110C 10C Protection at rated output current level Lit when the main circuit DC voltage is approximately 50 V or less. Indoors (with no corrosive gas, oil spray, or metallic dust) Operating: 10C to 50C Operating: 95% max. (with no condensation) 20C to 60C 1,000 m max. 5 M min. (Do not carry out any insulation resistance or withstand voltage tests) 9.8 m/s2 max. between 10 to 20 Hz 2.0 m/s2 max. between 20 and 50 Hz Panel-mounting models: Conforms to IP20
Voltage/frequency characteristics ProtecMotor protection tive i f func- Instantaneous overcurrent tions protection Overload protection Overvoltage protection Undervoltage protection Momentary power interruption compensation (selection) Cooling fin overheating Grounding protection Charge indicator (RUN indicator) Location Ambient temperature Ambient humidity Ambient temperature Altitude Insulation resistance Vibration resistance Degree of protection
Environment
Note 1. The power supply capacity is the capacity for the Inverters rated output. It will vary depending on the impedance at the input power supply. (This is due to fluctuations in the power factor. The power factor can be improved by inserting an AC reactor.) There will also be variations in the ratio between the rated current of the motor that is used and the rated output current of the Inverter. Note 2. The heat radiation is the electric power consumed in the Inverter at the Inverters rated output.
9-3
Specifications
3-phase p 400 V AC 400-V models Model 3G3JVPower Rated voltage and supply pp y frequency Allowable voltage fluctuation Allowable frequency fluctuation Power supply capacity (kVA) (See note 1.) Heat radiation (W) (See note 2.) Weight (kg) Cooling method A4002 A4004 A4007 A4015 3-phase 380 to 460 V AC at 50/60 Hz 15% to 10% 5%
Chapter 9
A4022 A4037
1.3 23.1
1.9 30.1
5.1 75.7
5.9 83.0
Max. applicable motor capacity (kW) Output p Rated output capacity (kVA) specifiifi Rated output current (A) cations Rated output voltage (V) Max. output frequency Control Harmonic-current characcountermeasures teristics Control method Carrier frequency Frequency control range Frequency precision (temperature characteristics) Frequency setting resolution
0.2 0.4 0.75 1.5 2.2 3.7 0.9 1.4 2.6 3.7 4.2 6.6 1.2 1.8 3.4 4.8 5.5 8.6 3-phase 380 to 460 V AC (according to the input voltage) 400 Hz parameter setting DC reactor (option) connection possible Sine wave PWM (V/f control) 2.5 to 10.0 kHz (in vector control) 0.1 to 400 Hz Digital commands: 0.01% (10C to 50C) Analog commands: 0.5% (25C 10C) Digital commands: 0.1 Hz (less than 100 Hz) and 1 Hz (100 Hz or over) Analog commands: 0.06 Hz/60 Hz (equivalent to 1/1000) 0.01 Hz 150% of rated output current for 1 min Selectable with FREQ adjuster: 0 to 10 V DC (20 k), 4 to 20 mA (250 ), and 0 to 20 mA (250 ) 0.0 to 999 s (Independent acceleration and deceleration time settings: 2 types) Approx. 20% (Braking Resistor and Braking Unit cannot be connected.) Set a user V/f pattern
Output frequency resolution Overload capacity External frequency set signal Acceleration/deceleration time Braking torque Voltage/frequency characteristics
9-4
Specifications
ProtecMotor protection i f tive func- Instantaneous overcurrent tions protection Overload protection Overvoltage protection Undervoltage protection Momentary power interruption compensation (selection) Cooling fin overheating Grounding protection Charge indicator (RUN indicator) Environ- Location ment Ambient temperature Ambient humidity Ambient temperature Altitude Insulation resistance Vibration resistance Degree of protection Protection by electronic thermal Stops at approx. 250% of rated output current
Chapter 9
Stops in 1 min at approximately 150% of rated output current Stops when main-circuit DC voltage is approximately 820 V Stops when main-circuit DC voltage is approximately 400 V Stops for 15 ms or more. By setting the Inverter to momentary power interruption mode, operation can be continued if power is restored within approximately 0.5 s. Detects at 110C 10C Protection at rated output current level Lit when the main circuit DC voltage is approximately 50 V or less. Indoors (with no corrosive gas, oil spray, or metallic dust) Operating: 10C to 50C Operating: 95% max. (with no condensation) 20C to 60C 1,000 m max. 5 M min. (Do not carry out any insulation resistance or withstand voltage tests) 9.8 m/s2 max. between 10 to 20 Hz 2.0 m/s2 max. between 20 and 50 Hz Panel-mounting models: Conforms to IP20
Note 1. The power supply capacity is the capacity for the Inverters rated output. It will vary depending on the impedance at the input power supply. (This is due to fluctuations in the power factor. The power factor can be improved by inserting an AC reactor.) There will also be variations in the ratio between the rated current of the motor that is used and the rated output current of the Inverter. Note 2. The heat radiation is the electric power consumed in the Inverter at the Inverters rated output.
9-5
Chapter 9
3G3JV-PSI485J
Fan Unit
3G3IV-PFANj
H Separate Accessory
Name Scaling Meter Model K3TJ-V11j Description Connected to the analog monitor output of the Inverter. The Scaling Meter displays the rpm or speed of the machine or line in actual units.
9-6
Specifications
H Dedicated Accessories
Name Digital Operator (with adjuster) Model 3G3IV-PJVOP140
Chapter 9
3G3IV-PJVOP146
3G3IV-PEZZ08386A
Description Operator used to perform operations for 3G3JV and 3G3MV Inverters. It is identical to the Digital Operator attached to standard 3G3MV Inverters, and has a built-in EEPROM in which the Inverters parameter settings can be stored. If the Digital Operator Case (3G3IV-PEZZ08386A) is used, the Inverter can be mounted in a control panel, or operated by remote control. Operator used to perform operations for 3G3JV and 3G3MV Inverters by remote control. It has a built-in EEPROM in which the Inverters parameter settings can be stored. Case for 3G3IV-PJVOP140 Digital Operator. Mounting a 3G3IV-PJVOP140 in the Case allows the Inverter to mounted in a control panel, or operated by remote control. Required when using a Digital Operator with 3G3JV Inverters. Cable length: 1 m, 3 m. Suppresses harmonic current generated from the Inverter and improves the power factor of the Inverter. An adapter making it possible to easily mount the Inverter to DIN tracks.
3G3IV-PRSj
3G3EV-PLNFDj
3G3IV-PLFj
9-7
Chapter 9
An Adapter Panel is required as an interface to connect a Digital Operator (3G3IV-PJVOP140 or 3G3IVPJVOP146) to the 3G3JV Inverter. There are two models of Adapter Panel available. The 3G3JV-PSI232J is permanently installed and cannot be removed and the 3G3JV-PSI232JC for copying parameters is installed so that it can be removed.
H Connections
3G3JV Inverter
Adapter Panel 3G3JV-PSI232J (permanent) 3G3JV-PSI232JC (removeable) Digital Operator 3G3IV-PJVOP146 3G3IV-PJVOP140 + 3G3IVPEZZ08386A (Digital Operator Case)
H Dimensions (mm)
D 3G3JV-PSI232J (Permanent)
9-8
Specifications
D 3G3JV-PSI232JC (Removeable)
Chapter 9
H Dimensions (mm)
9-9
Chapter 9
Replace the cooling fan if it has reached the end of its service life or a warning of cooling fan failure (FAN) is indicated.
H Applicable Models
3-phase p 200 V AC Inverter 3G3JV-A2007 3G3JV-A2015/-A2022 3G3JV-A2037 3G3JV-AB015 3G3JV-A4015/-A4022 3G3JV-A4037 Fan Unit 3G3IV-PFAN2007 3G3IV-PFAN2015J 3G3IV-PFAN2037 3G3IV-PFAN2015J 3G3IV-PFAN2015J 3G3IV-PFAN2037
H Replacement Method
Refer to 8-3 Maintenance and Inspection.
9-10
Specifications
H Standard Specifications
Input signal Measurement method Input impedance Sampling period Display refresh period Max. displayed digits Display Polarity display Zero display Scaling function
Chapter 9
DC voltage/current (0 to 20 mA, 4 to 20 mA, 0 to 5 V, 1 to 5 V, 5 V, 10 V) Double integral method Current input: 45 max., Voltage input: 1 M min. 250 ms Sampling period (sampling times multiplied by number of measurements for averaging if average processing is selected.) 5 digits (19999 to 99999) 7-segment digital display is displayed automatically with a negative input signal. Leading zeros are not displayed. Programmable with front-panel key inputs. The range of the display conforms to the maximum displayed digits. The decimal point position can be set as desired. Max hold (maximum value), Min hold (minimum value) Programmable with front-panel key inputs (0001 to 9999). Forced-zero (with front-panel key) Zero-limit Scaling teach function Display color change (green (red), green, red (green), red) OUT type change (upper limit, lower limit, upper/lower limit) Average processing (simple average: OFF or 2, 4, or 8 times) Relays: 2 SPST-NO 750 ms max. Front panel: NEMA4X for indoor use (equivalent to IP66) Rear case: IEC standard IP20 Terminals: IEC standard IP00 + finger protection (VDE0106/100) Non-volatile memory (EEPROM) (possible to rewrite 100,000 times)
Memory protection
H Connection Example
Inside the Inverter Circuit breaker R 3-phase S power supply T R S T SYSDRIVE Analog monitor E U V W + 10 to 10 VDC E5 GND K3MA-J A2 IM Analog output E4 A1
9-11
Specifications
H Dimensions (mm)
101.2 91 Terminal Cover (included) 75 min. 85 97 92+0.5 0 45 +0.5 0 120 min.
Chapter 9
12 96 48
Panel cut-out
1.3 80 44.8 7.6 mm 14.2 mm
H Dimensions (mm)
D 3G3IV-PJVOP140 (with Adjuster)
8 max.
3.6 dia
9-12
Specifications
D 3G3IV-PJVOP146 (without Adjuster)
Four, 4.4-dia. mounting holes
Chapter 9
H Dimensions (mm)
Four, 4.4-dia. mounting holes
9-13
Chapter 9
The Digital Operator Connection Cable (3G3IV-PCN126/PCN326) is required to connect a Digital Operator to a 3G3JV Inverter.
9-2-9 DC Reactor
H 3G3HV-PUZDABj
The DC Reactor suppresses harmonic current generated from the Inverter and improves the power factor of the Inverter. The DC Reactor suppresses harmonic current more effectively than the AC Reactor. Furthermore, the DC Reactor can be used in combination with the AC Reactor.
H Applicable Model
Inverter Voltage Max. applicaclass ble motor capacity (kW) 200 V 0.1 to 0.75 1.5 to 3.7 400 V 0.2 to 0.75 1.5 to 2.2 3.7 Model DC Reactor Rated Rated voltage current (V) (A) 800 V DC 5.4 18 800 V DC 3.2 5.7 12 Inductance (mH) 8 3 28 11 6.3 Loss (W)
8 18 9 11 16
9-14
Specifications
H External Dimensions (mm)
External Dimension 1 External Dimension 2 Two, d2 mounting holes
Chapter 9
Dimension (mm) H 53 76 53 60 76 W 85 86 85 90 86 W1 74 60 74 80 60 D 60 72 60 60 72 D1 32 55 32 32 55 D2 --80 ----80 t 0.8 1.2 0.8 0.8 1.2 d1 M4 M4 M4 M4 M4 d2 --M5 ----M5
H Applicable Model
Inverter 3-phase p 200 V AC 3G3JV-A2001/-A2002/-A2004/-A2007 3G3JV-A2015/-A2022 3G3JV-A2037 3G3JV-AB001/-AB002/-AB004 3G3JV-AB007/-AB015 3G3JV-A4002/-A4004/-A4007/-A4015/-A4022 3G3JV-A4037 DIN Track Mounting Bracket 3G3IV-PEZZ08122A 3G3IV-PEZZ08122B 3G3IV-PEZZ08122C 3G3IV-PEZZ08122A 3G3IV-PEZZ08122B 3G3IV-PEZZ08122B 3G3IV-PEZZ08122C
9-15
Specifications
H External Dimensions (mm)
3G3IV-PEZZ08122A 3G3IV-PEZZ08122B
Chapter 9
DIN track
Four, M4 tap
Four, M4 tap
3G3IV-PEZZ08122C
6 1.6
Four, M4 tap
9-16
DIN track
(35.1)
DIN track
(35.1)
(35.1)
Chapter 9
The AC Reactor suppresses harmonic current generated from the Inverter and improves the power factor of the Inverter. Connect the AC Reactor to the Inverter if the capacity of the power supply is much larger than that of the Inverter. Select the AC Reactor model from the following table according to the motor capacity.
H Connection Example
MCCB AC Reactor
Motor
H Applicable Range
AC Reactor required for smooth operation under present power supply conditions Power supply capacity (kVA) AC Reactor not required
2 2.5 5 10 15 20
9-17
Specifications
Model 3G3IV3G3IV PUZBABj 2A7.0MH 2.5A4.2MH 5A2.1MH 10A1.1MH 15A0.71MH 20A0.53MH Dimension (mm) A 120 120 120 130 130 130 B 71 71 71 88 88 88 (See note.) C 115 120 120 130 130 105 40 40 40 50 50 50 D 50 50 50 65 65 65 E F 105 105 105 130 130 130 20 20 20 22 22 22 H J M6 M6 M6 M6 M6 M6 K 10.5 10.5 10.5 11.5 11.5 11.5
Chapter 9
L 7 7 7 7 7 7
M M4 M4 M4 M4 M4 M5
Note B1 = 114
2.5 2.5 3 3 3
3G3IV-PUZBAB20A0.53MH
M Terminal Nameplate
Nameplate
9-18
Chapter 9
H Standard Specifications
Noise Filters for 3-phase 200 V AC Inverter Models
Inverter Model 3G3JVA2001/A2002/A2004/A2007 A2015/A2022 A2037 Noise Filter (Rasmi) for 3-phase 200 V AC Inverter models Model 3G3JVRated current (A) Weight (kg) PRS2010J 10 0.8 PRS2020J 16 1.0 PRS2030J 26 1.3
H Connection Example
MCCBs Noise Filter Clamp core
9-19
Specifications
H External Dimensions
Noise Filters for 3-phase 200 V AC Inverter Models D 3G3JV-PRS2010J
Chapter 9
21
D 3G3JV-PRS2020J
1.2
21
9-20
1.2
Specifications
D 3G3JV-PRS2030J
174 161 Three, 5-dia. holes 118 5 Four, M4 holes (for Inverter mounting use) 1 144 128 120 26 135 50 1.2
Chapter 9
21
1.2
25
9-21
Specifications
D 3G3JV-PRS1020J
Chapter 9
21
1.2
111
96
91
21
135
50
9-22
1.2
25
Specifications
D 3G3JV-PRS3010J
169 156 Three, 5-dia. holes 118
Chapter 9
111
96
91
21
135
50
1.2
25
9-23
Specifications
D 3G3JV-PRS3020J
174 161 Three, 5-dia. holes 118 5 Four, M4 holes (for Inverter mounting use) 1 144 128 120 26 135 50 1.2
Chapter 9
9-24
25
Specifications
H Applicable Models
Inverter Voltage Model
Chapter 9
3-phase p 200 V 3G3JV-A2001/-A2002/-A2004/-A2007 AC 3G3JV-A2015 3G3JV-A2022 3G3JV-A2037 Single-phase g p 3G3JV-AB001/-AB002 200 V AC 3G3JV-AB004 3G3JV-AB007 3G3JV-AB015 3-phase p 400 V 3G3JV-A4002/-A4004/-A4007 AC 3G3JV-A4015/-A4022 3G3JV-A4037
Simple Input Noise Filter Model Rated current Weight (kg) 3G3EV(A) PLNFD2103DY 10 0.2 PLNFD2153DY 15 0.2 PLNFD2203DY 20 0.4 PLNFD2303DY 30 0.5 PLNFB2102DY 10 0.1 PLNFB2152DY 15 0.2 PLNFB2202DY 20 0.2 PLNFB2302DY 30 0.3 PLNFD4053DY 5 0.3 PLNFD4103DY 10 0.4 PLNFD4153DY 15 0.4
H Connection Example
3-phase input Noise filter Single-phase input Noise filter
9-25
Specifications
H Dimensions
Dimensions 1 (Single-phase Input) Dimensions 2 (Three-phase Input)
Chapter 9
Model 3G3EV3G3EV PLNFD2103DY PLNFD2153DY PLNFD2203DY PLNFD2303DY PLNFB2102DY PLNFB2152DY PLNFB2202DY PLNFB2302DY PLNFD4053DY PLNFD4103DY PLNFD4153DY
Figure g (above) ( b ) 2
Dimension (mm) W 120 120 170 170 120 120 120 130 170 170 170 D 80 80 90 110 80 80 80 90 130 130 130 H max. 55 55 70 70 50 50 50 65 75 95 95 A 108 108 158 --108 108 108 118 ------------79 --------79 79 79 A B 68 68 78 98 68 68 68 78 118 118 118 Mounting screw M4 4, 20 mm M4 4, 20 mm M4 4, 20 mm M4 6, 20 mm M4 4, 20 mm M4 4, 20 mm M4 4, 20 mm M4 4, 20 mm M4 6, 30 mm M4 6, 30 mm M4 6, 30 mm
3 1
9-26
Specifications
H Connection Example
Noise filter
Chapter 9
H Applicable Models
Voltage class Inverter Max. applicable motor capacity (kW) 0.1 0.2 0.4 0.75 1.5 2.2 3.7 0.2 0.4 0.75 1.5 2.2 3.7 Inverter capacity (kVA) 0.3 0.6 1.1 1.9 3.0 4.2 6.7 0.9 1.4 2.6 3.7 4.2 6.5 Output Noise Filter Model Rated current (A)
200-V class
3G3IV-PLF310KA
10
3G3IV-PLF320KA 3G3IV-PLF310KB
20 10
400-V class
H Dimensions
External Dimensions
Weight g (k ) (kg)
9-27
10
Chapter 10 List of Parameters
List of Parameters
Parameter No. (Register No. (Hex)) n01 (0101) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to prohibit parameters to be written, sets parameters, or change the monitor range of parameters. Used to initialize parameters to default values. 0: Sets or monitors parameter n01. Parameters n02 through n79 can be monitored only. 1: Sets or monitors parameters n01 through n79. 5: Enables continuous operation. (Parameters n01 to n79 can be set or monitored.) 6: Clears the error log. 8: Initializes parameters to default values in 2-wire sequence. 9: Initializes parameters to default values in 3-wire sequence. Note With settings 0 or 1, operation commands are ignored in Program Mode. (Refer to 3-1-2 Drive Mode and Program Mode.) Normally, use a setting of 0 or 1.
0, 1, 6, 8, 9
No
5-2
n02 (0102)
Used to select the input method for the RUN and STOP commands in remote mode. 0: The RUN and STOP/RESET Keys on the Digital Operator are enabled. 1: Multi-function inputs through the control circuit terminals in 2- or 3-wire sequence. 2: Operation commands via RS-422/485 communications are enabled. Note The RUN command only through key sequences on the Digital Operator is acceptable in local mode.
0 to 2
No
5-7
n03 (0103)
Used to set the input method for the frequency reference in remote mode. 0: Digital Operator 1: Frequency reference 1 (n21) 2: Frequency reference control circuit terminal (0 to 10 V) 3: Frequency reference control circuit terminal (4 to 20 mA) 4: Frequency reference control circuit terminal (0 to 20 mA) 6: Frequency reference via RS-422/485 communications
0 to 4, 6
No
5-8
n04 (0104)
Used to set the stopping method for use when the STOP command is input. 0: Decelerates to stop in preset time. 1: Coasts to stop (with output shut off by the STOP command)
0, 1
No
5-17
n05 (0105)
Used to select the operation with the reverse command input. 0: Reverse enabled. 1: Reverse disabled.
0, 1
No
5-16
10-2
List of Parameters
Parameter No. (Register No. (Hex)) n06 (0106) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to select the stop method in remote mode with n02 for operation mode selection set to 1. 0: STOP/RESET Key of the Digital Operator enabled. 1: STOP/RESET Key of the Digital Operator disabled.
0, 1
No
5-7
n07 (0107)
Used to set the input method for the frequency reference in local mode. 0: The FREQ adjuster of the Digital Operator enabled. 1: Key sequences on the Digital Operator enabled.
0, 1
No
5-8
n08 (0108)
Used to enable the Enter Key for setting the frequency reference with the Increment and Decrement Keys. 0: The value is entered with the Enter Key pressed. 1: The value is enabled when the value is input.
0, 1
No
5-12
n09 (0109) n10 (010A) n11 (010B) n12 (010C) n13 (010D)
Maximum frequency (FMAX) Maximum voltage (VMAX) Maximum voltage frequency (FA) Middle output frequency (FB) Middle output frequency voltage (VC) Minimum output frequency (FMIN) Minimum output frequency voltage (VMIN) Acceleration time 1 Deceleration time 1 Acceleration time 2 Deceleration time 2
Used to set the V/f pattern as the basic characteristic of the Inverter with output voltage per frequency set.
Output voltage
60.0
No
5-4
No
5-4
No
5-4
Note
Set the parameters so that the followsatisfied. ing condition will be satisfied n14 x n12 < n11 x n09 The value set in n13 will be ignored if parameters n14 and n12 are the same i value. l in
1.5
No
5-4
12 (see note 2)
No
5-4
Note
0.1 to 10.0
0.1 Hz
1.5
No
5-4
1 to 50 (see note 2)
1V
No
5-4
Acceleration time: The time required to go from 0% to 100% of the maximum frequency. Deceleration time: The time required to go from 100% to 0% of the maximum frequency. Note The actual acceleration or deceleration time is obtained from the following for formula. Acceleration/Deceleration time = (Acceleration/Deceleration l ti /D l ti ti time set t value) l ) (Frequency reference value) (Max. frequency)
10.0
Yes
5-14
10.0
Yes
5-14
10.0
Yes
5-14
10.0
Yes
5-14
10-3
List of Parameters
Parameter No. (Register No. (Hex)) n20 (0114) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to set S-shape acceleration/deceleration characteristics. 0: No S-shape acceleration/deceleration (trapezoidal acceleration/deceleration) 1: S-shape acceleration/deceleration characteristic time 0.2 s 2: S-shape acceleration/deceleration characteristic time 0.5 s 3: S-shape acceleration/deceleration characteristic time 1.0 s Note When the S-shape acceleration/deceleration characteristic time is set, the acceleration and deceleration times will be lengthened according to the Sshape at the beginning and end of acceleration/deceleration.
0 to 3
No
5-15
n21 (0115) n22 (0116) n23 (0117) n24 (0118) n25 (0119) n26 (011A) n27 (011B) n28 (011C) n29 (011D)
Frequency reference 1 Frequency reference 2 Frequency reference 3 Frequency reference 4 Frequency reference 5 Frequency reference 6 Frequency reference 7 Frequency reference 8 Inching frequency command
Used to set internal frequency references. 0.0 to Note Frequency reference 1 is enabled in re- max. frequency y mote mode with n03 for frequency refer- q ence selection set to 1. Note These frequency references are selected with multi-step speed references (multi-function input). See the reference pages for the relationship between multi-step speed references and frequency references.
6.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
0.0
Yes
5-10
Used to set the inching frequency command. Note The inching frequency command is selected with the inching command (multifunction input). The inching frequency command takes precedence over the multi-step speed reference. Used to set the upper and lower frequency 0 to 110 reference limits in percentage based on the maximum frequency as 100%. Note If n31 is set to a value less than the minimum output frequency (n14), the Invert- 0 to 110 er will have no output when a frequency reference less than the minimum output frequency input is input. 1%
6.0
Yes
5-11
n30 (011E)
100
No
5-9
n31 (011F)
1%
No
5-9
10-4
List of Parameters
Parameter No. (Register No. (Hex)) n32 (0120) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to set the rated motor current for motor overload detection (OL1) based on the rated motor current. Note Motor overload detection (OL1) is disabled by setting the parameter to 0.0. Note
0.0 to 120% of rated output current of the InThe rated motor current is default to the verter. standard rated current of the maximum applicable motor. 0 to 2
0.1 A
No
5-2
n33 (0121)
Used to set the motor overload detection (OL1) for the electronic thermal characteristics of the motor. 0: Protection characteristics for general-purpose induction motors 1: Protection characteristics for inverter-dedicated motors 2: No protection Note If a single Inverter is connected to more than one motor, set the parameter to 2 for no protection. The parameter is also disabled by setting n32 for rated motor to 0.0.
No
6-14
n34 (0122)
Used to set the electric thermal characteristics 1 to 60 of the motor to be connected in 1-minute increments. Note The default setting does not require any changes in normal operation. Note To set the parameter according to the characteristics of the motor, check with the motor manufacturer the thermal time constant and set the parameter with some margin. In other words, set the value slightly shorter than the thermal time constant. To detect motor overloading quicker, reduce the set value, provided that it does not cause any application problems. 0, 1
1 min
No
6-14
Note
n35 (0123)
Used to operate the Cooling Fan of the Inverter while the Inverter is turned on or only while the Inverter is in operation. 0: Rotates only while RUN command is input and for 1 minute after Inverter stops operating 1: Rotates while Inverter is turned on Note This parameter is available only if the Inverter incorporates a Cooling Fan. Note If the operation frequency of the Inverter is low, the life of the fan can be prolonged by setting the parameter to 0.
No
6-14
10-5
List of Parameters
Parameter No. (Register No. (Hex)) n36 (0124) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Multi-function input p 1 (Input ( p t i l S2) terminal Multi-function input 2 (Input terminal S3)
Used to select the functions of multi-function input terminals S2 through S5. Set value 0 Function Forward/Reverse rotation command Description 3-wire sequence (to be set in n37 only) By setting n37 to 0, the set value in n36 is ignored and the following setting are forcibly made. S1: RUN input (RUN when ON) S2: STOP input (STOP when OFF) S3: Forward/Reverse rotation command (OFF: Forward; ON: Reverse) Reverse rotation command in 2-wire sequence (Reversed with the terminal turned ON) ON: External fault (FPj detection: j is a terminal number) OFF: External fault (EFj detection: j is a terminal number) ON: Fault reset (disabled while RUN command is input) Signals to select frequency references 1 through 8. Refer to 5-5-4 Setting Frequency References through Key Sequences p befor the relationship t tween multi-step lti t speed d references and frequency references. ON: Inching frequency command (taking precedence over the multi-step speed reference) ON: Acceleration time 2 and deceleration time 2 are selected.
2 to 8, 10 to 22 0, 2 to 8, 10 to 22
No
5-18
n37 (0125)
No
5-18
n38 (0126)
2 to 8, 10 to 22
No
5-18
n39 (0127)
Reverse/Stop
2 to 8, 10 to 22 34 22, 34, 35
No
5-18
Multi-step speed reference 1 Multi-step speed reference 2 Multi-step speed reference 3 Inching frequency command Acceleration/ Deceleration time changeover
10
11
10-6
List of Parameters
Parameter No. (Register No. (Hex)) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
12
External base block command (NO) External base block command (NC) Search command (Searching starts from maximum frequency) Search command (Searching starts from preset frequency) Acceleration/ Decelerationprohibit command Local or remote selection Communications or remote selection Emergency stop fault (NO) Emergency stop alarm (NO) Emergency stop fault (NC) Emergency stop alarm (NC) Up or down command
ON: Output shut off (while motor coasting to a stop and bb flashing) OFF: Output shut off (with motor free running and bb flashing) ON: Speed search (Searching starts from n09)
No
5-18
13
14
15
16
ON: Acceleration/Deceleration is on hold (running at parameter frequency) ON: Local mode (operated with the Digital Operator) ON: RS-422/485 communications input is enabled. OFF: The settings of n02 and n03 are enabled. The Inverter stops according to the setting in n04 for interruption mode selection with the emergency stop input turned ON. NO: Emergency stop with the contact closed. g y stop p with NC: Emergency the th contact t t opened. d Fault: Fault output is ON and reset with RESET input. Alarm output is ON (no reset required). STP is displayed (lit with fault input ON and flashes with alarm input ON) Up or down command (set in n39 only) By setting n39 to 34, the set value in n38 is ignored and the following setting are forcibly made. S4: Up command S5: Down command
17 18
19
20
21
22
34
35
Self-diagnostic test
10-7
List of Parameters
Parameter No. (Register No. (Hex)) n40 (0128) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to select the functions of multi-function output terminals. Set value 0 1 2 Function Fault output Operation in progress Frequency detection Description ON: Fault output (with protective function working) ON: Operation in progress ON: Frequency detection (with frequency reference coinciding with output frequency) ON: Idling (at less than min. output frequency) ON: Output frequency y frequency detection level (n58) ON: Output frequency x frequency detection level (n58) Output if any of the following parameter conditions is satisfied. n59: Overtorque detection function selection n60: Overtorque detection level n61: Overtorque detection time NO contact: ON with overtorque being detected NC contact: OFF with overtorque being detected --ON: Alarm being detected (Nonfatal error being detected) Base block in progress (in operation with output shutoff) ON: Local mode (with the Digital Operator) ON: Inverter ready to operate (with no fault detected) ON: Fault retry ON: Undervoltage being monitored ON: Rotating in reverse direction ON: Speed search in progress
0 to 7, 10 to 17
No
5-21
3 4
Idling Frequency detection 1 Frequency detection 2 Overtorque being monitored (NOcontact output)
8 9 10
11
12 13
14 15 16 17
10-8
List of Parameters
Parameter No. (Register No. (Hex)) n41 (0129) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Frequency reference gain Frequency reference bias Analog frequency reference time Analog monitor output
Used to the input characteristics of analog frequency references. Gain: The frequency of maximum analog input (10 V or 20 mA) in percentage based on the maximum frequency as 100%. Bias: The frequency of minimum analog input (0 V or 0 or 4 mA) in percentage based on the maximum frequency as 100%. Used to set the digital filter with a first-order lag for analog frequency references to be input. Used to set the output frequency or current as a monitored item. 0: Output frequency (10-V output at max. frequency with n45 set to 1.00). 1: Output current (10-V output with Inverter rated output current with n45 set to 1.00)
0 to 255
1%
100
Yes
5-9
n42 (012A)
99 to 99
1%
Yes
5-9
0.00 to 2.00 0, 1
0.01 s
0.10
No
5-10
No
5-23
0.00 to 2.00
0.01
1.00
Yes
5-23
Used to set the carrier frequency. 1 to 4, Note The default setting does not need any 7 to 9 changes in normal operation. Note Refer to 6-1 Setting the Carrier Frequency for details. 0 to 2
No
6-2
n47 (012F)
Used to specify the processing that is performed when a momentary power interruption occurs. 0: Inverter stops operating 1: Inverter continues operating if power interruption is 0.5 s or less. 2: Inverter restarts when power is restored.
No
6-15
n48 (0130)
Fault retry
Used to set the number of times the Inverter is reset and restarted automatically in the case the Inverter has an overvoltage fault, overcurrent fault, or ground fault.
0 to 10
No
6-15
10-9
List of Parameters
Parameter No. (Register No. (Hex)) n49 (0131) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Jump frequency 1
0.0 to 400
0.0
No
6-16
n51
n50 (0132)
Jump frequency 2
0.0 to 400
0.0
No
6-16
Frequency reference
n51 (0133)
n50
n49
0.0 to 25.5
0.1 Hz
0.0
No
6-16
These values must satisfy the following condition: n49 y n50 0 to 100 0.0 to 25.5 1% 50 No 6-5
DC control current Interruption DC control time Startup DC control time Stall prevention during deceleration
Used to impose DC on the induction motor for braking control. Set the DC braking percentage g current in p g based th rated t d current t of f the th Inverter I t as 100%. 100% on the
0.1 s
0.5
No
6-5
0.0 to 25.5 0, 1
0.1 s
0.0
No
6-5
Used to select a function to change the deceleration time of the motor automatically so that there will be no overvoltage imposed on the motor during deceleration. 0: Stall prevention during deceleration enabled 1: Stall prevention during deceleration disabled
No
6-6
n56 (0138)
Stall prevention level during acceleration Stall prevention level during operation
Used to select a function to stop the acceleration of the motor automatically for stall prevention during acceleration. Set the level in percentage based on the rated current of the Inverter as 100%. Used to select a function to reduce the output frequency of the Inverter automatically for stall prevention during operation. Set the level in percentage based on the rated current of the Inverter as 100%.
30 to 200
1%
170
No
6-7
n57 (0139)
30 to 200
1%
160
No
6-8
n58 (013A)
Used to set the frequency to be detected. 0.0 to Note The parameter n40 for multi-function output 400 must be set for the output of frequency detection levels 1 and 2. Used to enable or disable overtorque detection and select the processing method after overtorque detection. 0: Overtorque detection disabled 1: Overtorque detection only when speed coincides and operation continues (issues alarm) 2: Overtorque detection only when speed coincides and output shut off (for protection) 3: Overtorque always detected and operation continues (issues alarm) 4: Overtorque always detected and output shut off (for protection) 0 to 4
0.1 Hz
0.0
No
6-18
n59 (013B)
No
6-9
10-10
List of Parameters
Parameter No. (Register No. (Hex)) n60 (013C) n61 (013D) n62 (013E) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Overtorque detection level Overtorque detection time UP/DOWN command frequency memory
Used to set overtorque detection level. Set the level in percentage based on the rated current of the Inverter as 100%. Used to set the detection time of overtorque.
30 to 200
1%
160
No
6-9
0.1 to 10.0 0, 1
0.1 s
0.1
No
6-10
Used to store the adjusted frequency reference with the UP/DOWN function. 0: Frequency not stored 1: Frequency stored The frequency must be on hold for 5 s or more. Used to store the adjusted frequency reference with the UP/DOWN function. 0: Frequency not stored 1: Frequency stored The frequency must be on hold for 5 s or more. Used to store the adjusted frequency reference with the UP/DOWN function. 0: Frequency not stored 1: Frequency stored The frequency must be on hold for 5 s or more.
No
6-19
n63 (013F)
Used to set the gain of the torque compensation function. The default setting does not need any changes in normal operation.
0.0 to 2.5
0.1
1.0
Yes
6-11
n64 (0140)
Used to set the rated slip value of the motor in use. 0.0 to Note Used as the constant of the slip compensation 20.0 function. Used to set the no-load current of the motor in use 0 to 99 based on the rated motor current as 100%. Note Used as the constant of the slip compensation function. Used to set the gain of the slip compensation func0.0 to tion. 2.5 Note The slip compensation function is disabled with n66 set to 0.0. Used for the response speed of the slip compensa0.0 to tion function. 25.5 Note The default setting does not need any changes in normal operation. Used to set whether a communications time-over (CE) is detected if there is an interval of more than 2 s, and to select the method of processing the detected communications time-over. 0: Detects a time-over and fatal error and coasts to a stop. 1: Detects a time-over and fatal error and decelerates to a stop in deceleration time 1. 2: Detects a time-over and fatal error and decelerates to a stop in deceleration time 2. 3: Detects a time-over and nonfatal error warning and continues operating. 4: No time-over is detected. 0 to 4
0.1 Hz
Yes
6-12
n65 (0141)
1%
No
6-12
n66 (0142)
0.1
Yes
6-12
n67 (0143)
0.1 s
2.0
No
6-12
No
7-5
10-11
List of Parameters
Parameter No. (Register No. (Hex)) n69 (0145) (See note 3.) Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Used to the set the unit of frequency reference and frequency-related values to be set or monitored through communications. 0: 0.1 Hz 1: 0.01 Hz 2: Converted value based on 30,000 as max. frequency 3: 0.1% (Max. frequency: 100%)
0 to 3
No
7-5
Used to set the Slave address (Slave unit number) for communications. 0: 01 to 32: Only receives broadcast messages from the Master. Slave address
00 to 32
00
No
7-6
Used to set the baud rate for communications. 0: 2,400 bps 1: 4,800 bps 2: 9,600 bps 3: 19,200 bps
0 to 3
No
7-6
n72 (0148) (See note 3.) n73 (0149) (See note 3.) n74 (014A) (See note 3.) n75 (014B)
Used to set the parity for communications. 0: Even parity 1: Odd parity 2: No parity
0 to 2
No
7-7
Used to set the waiting period for returning a response after the DSR (data-send-request) message is received from the Master.
10 to 65
1 ms
10
No
7-7
Select whether or not to enable the RTS (request-tosend) communications control function.
0, 1
No
7-7
Low-speed carrier frequency reduction selection Parameter copy and verify function
Used to select a function to reduce the carrier frequency when Inverter is at low speed. 0: Function disabled 1: Function enabled Note Normally set n75 to 0. Selects the function to read, copy, and verify the parameter between the memory of the Inverter and that of the Digital Operator. rdy: Ready to accept the next command. rED: Reads the Inverter parameter. Cpy: Copies the parameter to the Inverter. vFY: Verifies the Inverter parameter. vA: Checks the Inverter capacity display. Sno: Checks the software number.
0.1
No
6-4
rdy to Sno
---
rdy
No
---
Select the copy-prohibit function. Use this parameter to protect the data in the EEPROM of the Digital Operator. 0: Read prohibited for Inverter parameters. (Data cannot be written to EEPROM.) 1: Read possible for Inverter parameters. (Data can be written to EEPROM.)
0, 1
No
---
10-12
List of Parameters
Parameter No. (Register No. (Hex)) n78 (014E) Display Note will be displayed if no error has been recorded. This parameter is monitored only. ------Name Description Setting range Unit of setting Default setting
Chapter 10
Changes during operation Reference page
Error log
---
---
---
---
6-21
Used to display the software number of the Inverter for OMRONs control reference use. Note This parameter is monitored only.
---
---
Note 1. Values will be set in 0.1-Hz increments if the frequency is less than 100 Hz and 1-Hz increments if the frequency is 100 Hz or over. With RS-422/485 communications, the unit is always 0.1 Hz. Note 2. With 400-V Inverters, the values for the upper limit of setting ranges and the default settings will be twice those given in the above table. Note 3. The n68, n74, n76, and n77 parameters cannot be written via RS422/485 communications. They are read-only.
10-13
11
Chapter 11 Using the Inverter for a Motor
Chapter 11
When a standard motor is operated with the Inverter, a power loss is lightly higher than when operated with a commercial power supply. In addition, cooling effects also decline the low-speed range, resulting in an increase in the motor temperature. Therefore, motor torque should be reduced in the low speed range. The following figure shows allowable load characteristics of a standard motor. If 100% torque is continuously required in the low-speed range, use a special motor for use with Inverters.
Allowable Load Characteristics of Standard Motor 25% ED (or 15 min) 40% ED (or 20 min) 60% ED (or 40 min)
100 80 70 60 50
Torque (%)
Continuous
0 3 10 20
Frequency (Hz)
60
D High-speed Operation
When using the motor at high-speed (60 Hz or more), problems may arise in dynamic balance and bearing durability.
D Torque Characteristics
The motor may require more acceleration torque when the motor is operated with the Inverter than when operated with a commercial power supply. Check the load torque characteristics of the machine to be used with the motor to set a proper V/f pattern.
D Vibration
The 3G3JV Series employs high carrier PWM control to reduce motor vibration. When the motor is operated with the Inverter, motor vibration is almost the same as when operated with a commercial power supply. Motor vibration may, however, become greater in the following cases. Resonance with the natural frequency of the mechanical system Take special care when a machine that has been operated at a constant speed is to be operated in variable speed mode. If resonance occurs, install vibration-proof rubber on the motor base. Imbalance rotor Take special care when the motor is operated at a high speed (60 Hz or more).
11-2
Chapter 11
Noise is almost the same as when the motor is operated with a commercial power supply. Motor noise, however, becomes louder when the motor is operated at a speed higher than the rated speed (60 Hz).
D Submersible Motor
The rated input current of submersible motors is higher than that of standard motors. Therefore, always select an Inverter by checking its rated output current. When the distance between the motor and Inverter is long, use a cable thick enough to connect the motor and Inverter to prevent motor torque reduction.
D Explosion-proof Motor
When an explosion-proof motor or increased safety-type motor is to be used, it must be subject to an explosion-proof test in conjunction with the Inverter. This is also applicable when an existing explosionproof motor is to be operated with the Inverter.
D Gearmotor
The speed range for continuous operation differs according to the lubrication method and motor manufacturer. In particular, the continuous operation of an oil-lubricated motor in the low speed range may result in burning. If the motor is to be operated at a speed higher than 60 Hz, consult with the manufacturer.
D Synchronous Motor
A synchronous motor is not suitable for Inverter control. If a group of synchronous motors is individually turned on and off, synchronism may be lost.
D Single-phase Motor
Do not use the Inverter for a single-phase motor. The motor should be replaced with a 3-phase motor.
11-3
Chapter 11
1.1 1.8 3.9 6.4 11.0 15.1 24.0 1.8 3.5 7.4 12.8 20.5 1.6 2.4 4.7 7.0 8.1 10.6 12.0 3.2 6.2
ABS33b3A ABS33b3A ABS33b5A ABS33b10A ABS33b15A ABS33b20A ABS33b30A ABS32b3A ABS32b5A ABS32b10A ABS32b15A ABS32b30A ABS33b3A ABS33b5A ABS33b5A ABS33b10A ABS33b15A ABS33b15A ABS33b20A ABS33b10A ABS33b15A
3 3 5 10 15 20 30 3 5 10 15 30 3 5 5 10 15 15 20 10 15
ABS33b3A ABS33b3A ABS33b5A ABS33b10A ABS33b10A ABS33b15A ABS33b20A ABS32b3A ABS32b5A ABS32b10A ABS32b15A ABS32b20A ABS33b3A ABS33b3A ABS33b5A ABS33b10A ABS33b10A ABS33b10A ABS33b15A ABS33b10A ABS33b15A
3 3 5 10 10 15 20 3 5 10 15 20 3 3 5 10 10 10 15 10 15
J7L-09 J7L-09 J7L-09 J7L-09 J7L-18 J7L-22 J7L-40 J7L-09 J7L-09 J7L-09 J7L-18 J7L-40 J7L-09 J7L-09 J7L-09 J7L-09 J7L-18 J7L-18 J7L-22 J7L-12 J7L-18
J7L-09 J7L-09 J7L-09 J7L-09 J7L-09 J7L-18 J7L-22 J7L-09 J7L-09 J7L-09 J7L-18 J7L-22 J7L-09 J7L-09 J7L-09 J7L-09 J7L-09 J7L-12 J7L-18 J7L-12 J7L-18
100 V, singlephase
0.1 0.2
11-4
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version.
Revision code
01 02
Date
May 1999 December 1999 Original production
Revised content
The following Inverters with different capacities were added to the manual: 3G3JBA2037/A4002/A4004/A4007/A4015/A4022/A40 37, and additions and corrections were made. Specific changes are listed below. Preliminary : Caution changed to WARNING in 2 places under Installation Precaution. Information for new models added under Contents of Warning and Checking the Product. Page 1-2: Information for new models added to first table. Page 1-6: Information added to STOP/RESET Key description. Note added after table. Page 2-3: Information added for new models. Page 2-4: Caution changed to WARNING in 2 places and order changed. Page 2-11: Information for new models added to graphics on top right. Page 2-12: Information for new models added to table. Page 2-13: Information added for new models. Note added after table. Page 2-15: Information for new models added to graphics. Page 2-17: Information added for new models. Page 2-18: Table for 400-V AC models added. Page 2-19: Information for new models added to diagram. Page 2-20: Information added for installing a magnetic contactor. Page 2-21: Information added regarding noise filters. Page 224: Information added regarding cable lengths between Inverters and motors. Page 2-25: Information added regarding ground wiring for 400-V models. Page 2-28: Information added to wiring method graphics. Page 2-32: Information added to main circuit terminals graphic. Page 2-33: Information for new models added to tables. Page 2-34: Information added regarding Lowvoltage Directive conformance. Page 3-3: Information added regarding STOP/ RESET Key. Note added after table. Page 3-8: Information added to note 3 following table. Page 3-9: Note 3 added after table. Page 4-4: Information added regarding power connection. Page 4-6: Information added regarding power connection. Page 5-6: Information added regarding local/ remote selection methods. Page 5-18: Notes 2 and 3 added after table. Page 5-22: Information added regarding external base block command. Page 5-23: Note added after table. Page 6-3: Information for new models added to table. Page 7-3: Information for new models added to table. Page 7-7: Information for new models added to table. Page 7-14: Information added for new models. Page 7-17: Information added regarding errors and malfunctions. Page 7-20: Information added for new models. Page 8-2: Information added to first table regarding power supply capacity and braking torque. Notes added after table. Table for 400-V models added. Page 8-4: Model number changed in last table. Page 8-5: Information regarding input noise filter removed. Information regarding new models added to table. Page 8-7: Information added to table. Page 8-8: Information for new models added to tables. Pages 8-8 and 8-9: 3G3IV-PZZ08122 changed to 3G3IV-PEZZ08122. Page 8-9: Graphics added. Page 8-10: Information for new models added. Page 8-11: Information for new models added. Pages 8-12 and 8-13: Graphics added. Page 8-14: Information for new models added. Page 8-15: Information for new models added to table. Pages 8-15 and 8-16: Information regarding input noise filter removed. Page 8-17: Information for new models added to tables.
03
October 2001
Pages 2-2, 2-3: Information on dimensions added. Page 2-11: Minor change made to second table. Page 5-7: Two corrected to three in intro paragraph. Pages 5-7, 5-8, 5-9, 5-18, 7-5, 7-6, 7-7, and 8-6: Information added to or deleted from tables. Page 5-8: Five changed to six in intro paragraph. Page 7-1: New chapter added. Pages 8-7 and 8-9: Information on option products added. Page 9-2: Register numbers added throughout table and information added in several places. Page 9-8: Information added in 2 places. Pages 9-12 and 9-14: Information changed and added in several places.
R-1
Revision History
Revision code
04
Date
November 2005
Revised content
General precautionary notes added to the first page. Notice: Information on general precautions notation added. Read and Understand this Manual: Information on liability and warranty added. Page 1-2: Changed note. Page 2-29: Corrected cable length in paragraph above last table. Page 3-2: Added heading. Page 3-3: Added section. Page 3-4: Changed heading. Page 3-8: Added section. Page 5-2: Added row and note to table. Page 7-35: Moved note to next page. Page 7-36: Added note, replaced diagram, and added diagram. Pages 7-40 and 7-42: Changed PC to PLC. Page 9-9: Added model number of connector to diagram. Page 9-10: Replaced section. Pages 9-16 and 9-17: Added power specifications to heading. Page 10-2: Added set value and note to n01. Page 11-4: Added table.
05
February 2008
R-2