Professional Documents
Culture Documents
Microwave/Grill Oven: Service Manual
Microwave/Grill Oven: Service Manual
MODEL : MB-339ME/MB
CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel. Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be taken to avoid possible exposure to excessive microwave energy.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open. B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse. C) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
CONTENTS
(Page)
SAFETY PRECAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Inside front cover SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1 CAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1 INSTALLATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1 OPERATING INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
FEATURES- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 CONTROL PANEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 OPERATING SEQUENCE- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-2 SCHEMATIC DIAGRAM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 CIRCUIT DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-4
EXPLODED VIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1 REPLACEMENT PARTS LIST - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1 SCHEMATIC DIAGRAM OF P.C.B. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1
PRINTED CIRCUIT BOARD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2
SPECIFICATIONS
ITEM
MODEL
Power Requirement
DESCRIPTION
MB-339ME/MB
120 Volts AC 60 Hz MICROWAVE........................... 1,300 Watts (12.0A) GRILL....................................... 1,000 Watts (8.5A) Single phase, 3 wire grounded
Power Output Microwave Frequency Magnetron Timer Outside Dimensions Cavity Dimensions Net Weight Shipping weight Control Complement
900 Watts full microwave power (IEC705) 2,450 MHz 2M214-39 0 ~ 99 min. 99 sec. 530mm (W) x 315mm (H) x 394mm (D) 348mm (W) x 222mm (H) x 373mm (D) 14.9 Kg (approx.) 16.7 Kg (approx.) Touch Control System Clock : 1:00 - 12:59 Microwave Power for Variable Cooking Power level HIGH - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Full power throughout the cooking time 9 (Saute) - - - - - - approx. 90% of Full power, 8 (Reheat) - - - - - - - - approx. 80% 7 (Med.-High) - - - - - - - - - - - - - - approx. 70%, 6 (Medium) - - - - - - - - approx. 60% 5 (Med.-Low) - - - - - - - - - - - - - - - approx. 50%, 4 (Defrost) - - - - - - - - - approx. 40% 3 (Low) - - - - - - - - - - - - - - - - - - - - approx. 30%, 2 (Simmer) - - - - - - - - - approx. 20% 1 (Warm) - - - - - - - - - - - - - - - - - - approx. 10%
Nameplate Location
Back Side
Accessories
Owner's manual & cooking guide Glass turntable Rotating ring Grill rack
This microwave oven is designed for household use only. It is not recommended for commercial purposes.
1-1
CAUTIONS
Unlike other appliances, the microwave oven is high-voltage and high-current equipment. Though it is free from danger in ordinary use, extreme care should be taken during repair.
DO NOT operate on a 2-wire extension cord during repair and use. NEVER TOUCH any oven components or wiring during operation. BEFORE TOUCHING any parts of the oven, always remove the power plug from the outlet. For about 30 seconds after the oven stops, an electric charge remains in the high voltage capacitor. When replacing or checking, you must discharge the high voltage capacitor by shorting across the two terminals with an insulated screwdriver.
MICROWAVE RADIATION
Personnel should not be exposed to the microwave energy which may radiate from the magnetron or other microwave generating device if it is improperly used or connection. All input and output microwave connections, waveguide, flange, and gasket must be secure never operate the device without a microwave energy absorbing load attached. Never look into an open waveguide or antenna while the device is energized. Proper operation of the microwave oven requires that the magnetron be assembled to the waveguide and cavity. Never operate the magnetron unless it is properly installed. Be sure that the magnetron gasket is properly installed around the dome of the tube whenever installing the magnetron.
ANTENNA
Gasket
Remove your watches whenever working close to or replacing the Magnetron. DO NOT touch any parts of the control panel circuit. A resulting static electric discharge may damage this P.C.B. NEVER operate the oven with no load. NEVER injure the door seal and front plate of the oven cavity. NEVER put iron tools on the magnetron. NEVER put anything into the latch hole and the interlock switches area.
MAGNETRON
2-1
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
INSTALLING
1. Empty the microwave oven and clean inside it with a soft, damp cloth. Check for damage such as misaligned door, damage around the door or dents inside the cavity or on the exterior. 2. Put the oven on a counter, table, or shelf that is strong enough to hold the oven and the food and utensils you put in it. (The control panel side of the oven is the heavy side. Use care when handling.) 3. Do not block the vent and the air intake openings. Blocking vent or air intake openings can cause damage to the oven and poor cooking results. Make sure the microwave oven legs are in place to ensure proper air flow. 4. The oven should not be installed in any area where heat and steam are generated, because they may damage the electronic or mechanical parts of the unit. Do not install the oven next to a conventional surface unit or above a conventional wall oven. 5. Use microwave oven in an ambient temperature less than 104F (40C). 6. Place the microwave oven on a sturdy and flat surface at least 10 cm (4 inches) from the wall. 7. Place the microwave oven as far away as possible from TV, RADIO, COMPUTER, etc., to prevent interference.
GROUNDING INSTRUCTIONS
For personal safety, this appliance must be fully grounded at all times. In the event of an electrical short circuit, grounding reduces the risk of electrical shock. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING
Improper use of the grounding plug can result in a risk of electric shock.
10cm
3-1
OPERATING INSTRUCTIONS
FEATURES
Oven Front Plate Window Door Screen Door Seal Display Window Control Panel Door Open Button Safety Door Lock System Turntable Grill Rack Rotating Ring
CONTROL PANEL
1. ONE TOUCH COOK: To select the desired auto cook setting
14
2. GRILL 3. CUSTOM SET: You can select ON/OFF of beeper, automatic start or manual start of the one touch cook, and food weight measurement unit, pounds or kilograms. 4. COMBI
Papas Al Horno Huevo Pollo
Cocinado Al Toque
1
Palomitas Arroz Pizza
5. TIME ADJUSTMENT PADS: To set the cooking time. 6. POWER: To select the desired power level for cooking. 7. QUICK START: To set the cooking time and directily start.
2 3 5 8
Grill
Programa Personal
Combi
4 6 7
8. AUTO WEIGHT DEFROST: To select the desired auto weight defrost programmed with weight pad. 9. NUMBER 10. CLOCK: To set the clock. 11. HOLD WARM: To keep the food warm after the cooking is done. 12. STOP/CLEAR: To stop oven and clear all entries except time of day.
Potencia
Inicio Rpido
2 5 8 0
3 6 9
Reloj
9 11 12
4 7
Mantener Caliente
10 13
13. START: One tap allows oven to begin functioning. 14. DISPLAY WINDOW: Provides indications of the functions selected, normally current time displayed.
Parar/Borrar
Inicio
4-1
OPERATING SEQUENCE
The following is a description of component functions during oven operation.
INICIO
2. CANCEL FUNCTION
Touch the PARAR/BORRAR pad whenever you need to cancel an entry or a function currently in use. The display will either return to the last item entered or to the clock.
LOCK
9. CUSTOM SET
You can select ON/OFF of beeper, automatic start or manual start of the one touch cook, and food weight measurement unit, pounds or kilograms. Lbs/kg of beeper PARAR/BORRAR PROGRAMA PERSONAL 1 INICIO
3. QUICK START
PARAR/BORRAR INICIO RAPIDO
5. TIME COOKING
PARAR/BORRAR TIEMPO NUMBER NUMBER INICIO POTENCIA
6. MULTI-STAGE COOKING
1ST STAGE
PARAR/BORRAR TIEMPO NUMBER NUMBER POTENCIA
2ND STAGE
TIEMPO NUMBER NUMBER INICIO POTENCIA
4-2
SCHEMATIC DIAGRAM
4-3
IMPORTANT SAFETY NOTE: THE SHADED AREAS ON THIS SCHEMATIC DIAGRAM INCORPORATE SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM MICROWAVE RADIATION, FIRE, ELECTRICAL SHOCK, AND HAZARDS. WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURER'S SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SHADED AREAS OF THE SCHEMATIC DIAGRAM. NOTICE: SINCE THIS IS BASIC SCHEMATIC DIAGRAM, THE VALUES OF COMPONENTS AND SOME PARTIAL CONNECTIONS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
CIRCUIT DESCRIPTION
GENERAL DETAILS
The low voltage transformer supplies the necessary voltage to the micom controller when power cord is plugged in. When the door is closed, the primary switch is ON, the secondary switch is ON, and the monitor switch opens (contact COM and NO). A high voltage of approximately 2100 volts AC is generated in the secondary of the high voltage transformer which is increased by the action of the high voltage diode and charging of the high voltage capacitor. The negative 4,000 Volts DC is applied to the filament of the magnetron.
FUSE
RELAY 2
L
MICOM CONTROLLER MONITOR SWITCH H.V. TRANSFORMER
The fan motor rotates and cools the magnetron by blowing the air (coming from the intake on the baseplate). The air is also directed into the oven to exhaust the vapor in the oven through the upper plate. Cooking time starts counting down. 3.3 volts AC is generated from the filament winding of the high voltage transformer. This 3.3 volts is applied to the magnetron to heat the magnetron filament through two noise-preventing choke coils.
PRIMARY SWITCH
RELAY 2
SECONDARY SWITCH
MICOM CONTROLLER
4-4
SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS
Tools normally used for TV servicing are sufficient. Standard tools are listed below. Diagonal pliers Long nose pliers Phillips screwdriver Flat blade screwdriver Wrench (size 5mm) Nutdriver (size 5mm) Adjustable wrench Soldering iron Solder Vinyl insulation tape Polishing cloth
5-1
5-2
The microwave power output P in watts is calculated from the following formula : P= 4187 x (T) T
is measured while the microwave generator is operating at full power. Magnetron filament heat-up time is not included. (about 3 sec) The water is stirred to equalize temperature throughout the vessel, prior to measuring the final water temperature. Stirring devices and measuring instruments are selected in order to minimize addition or removal of heat. WATER LOAD
TURNTABLE
5-3
5-4
F. MAGNETRON REMOVAL
1) Disconnect the leadwire from the magnetron. 2) Carefully remove the mounting screws holding the magnetron and the waveguide. 3) Lift magnetron at a 30 angle to the waveguide with the magnetron hanger unhooked. 4) Remove the magnetron assembly until the tube is clear from the waveguide. NOTE: 1. When removing the magnetron, make sure its dome does not hit any adjacent parts, or it may be damaged. 2. When replacing the magnetron, be sure to install the magnetron gasket in the correct position and be sure that the gasket is in good condition. 3. After replacing the magnetron, check for microwave leakage with a survey meter around the magnetron. Microwave energy must be below the limit of 5 mW/cm2. (With a 275 ml. water load). Make sure that gasket is rigidly attached to the magnetron. To prevent microwave leakage, tighten the mounting screws properly, making sure there is no gap between the waveguide and the magnetron. Remove magnetron
30
Screw Magnetron Pull out suction guide Main ASSY Wave guide and magnetron Waveguide Magnetron hanger Dome
5-5
Connecting hook
Suction Guide
5-6
M. INTERLOCK SYSTEM
1) INTERLOCK MECHANISM The door lock mechanism is a device which has been specially designed to eliminate completely microwave activity when the door is opened during cooking and thus to prevent the danger resulting from the microwave leakage. 2) MOUNTING OF THE PRIMARY/MONITOR/ SECONDARY SWITCHES TO THE LATCH BOARD
ADJUSTMENT DIRECTION
SECONDARY SWITCH
Wire Leads
3) INSTALLATION AND ADJUSTMENT OF THE LATCH BOARD TO THE OVEN ASSEMBLY Mount the latch board to the oven assembly. Adjust the latch board in the arrow direction so that oven door will not have any play in it when the door is closed. Tighten the mounting screw. Check for play in the door by pushing the door release button. Door movement should be less than 0.5 mm. (1/64 inch) Don't push the door release button while making this adjustment. Make sure that the latch moves smoothly after adjustment is completed and that the screws are tight. Make sure the primary, monitor, and secondary switches operate properly by following the continuity test procedure.
Turntable Motor
5-7
COMPONENTS
SWITCHES (Wire leads removed)
TEST PROCEDURE
Check for continuity of the switch with an Ohm-meter Primary Switch
NO COM
RESULTS
Door open Door closed
NC COM
NO COM
NOTE : After checking for the continuity of switches, make sure that they are connected correctly.
5-8
COMPONENTS
HIGH VOLTAGE TRANSFORMER (Wire leads removed)
TEST PROCEDURE
RESULTS
FILAMENT WINDING
1. Measure the resistance. (Ohm-meter scale: Rx1 and Rx100) Primary winding Secondary winding Filament winding 2. Measure the resistance. (Ohm-meter scale: Rx1000) Primary winding to ground Filament winding to ground MAGNETRON (Wire leads removed) 1. Measure the resistance. (Ohm-meter scale: Rx1) Filament terminal 2. Measure the resistance. (Ohm-meter scale: Rx1000) Filament to chassis
Approx.: 0.3 ~ 0.6 ohm Approx.: 70 ~ 100 ohm Less than: 1 ohm
Normal: Infinite
5-9
COMPONENTS
TEST PROCEDURE
Antenna Gasket Chassis
RESULTS
Filament
NOTE: When testing the magnetron, be sure to install the magnetron gasket in the correct position and be sure that the gasket is in good condition. HIGH VOLTAGE CAPACITOR Measure the resistance. (Ohm-meter scale: Rx1000) Terminal to terminal. Normal: Momentarily indicates several ohms, and then gradually returns to infinite.
Normal: Infinite.
NOTE : Some inexpensive meters may indicate infinite resistance in both direction.
5-10
COMPONENTS
HEATER ELEMENT (Wire leads removed.)
TEST PROCEDURE
Measure the resistance. (Multi-meter scale:RX1)
RESULTS
Normal: Gill heater Approx.55 (at 20-30C)
NOTE: Make sure heater is fully cooled when tested. MAGNETRON THERMOSTAT 0C~Approx 180C Approx 180C
OVEN THERMOSTAT
Normal
Abnormal
NOTE: If the fuse is blown, check primary, the secondary, the monitor switches, H.V.D and H.V.C before replacing the fuse. If the fuse is blown by improper switch operation replace the defective switch and the fuse at the same time. Replace just the fuse if the switches operate normally.
5-11
COMPONENTS
RELAY 2
TEST PROCEDURE
Check for continuity of relay 2 with an ohm-meter. (Remove wire leads from relay 2 and operate the unit.) POWER LEVEL 1 2 3 4 5 6 7 8 9 10
RESULTS
4 sec 6 sec 8 sec 10 sec 12 sec 14 sec 16 sec 18 sec 20 sec 22 sec
18 sec 16 sec 14 sec 12 sec 10 sec 8 sec 6 sec 4 sec 2 sec 0 sec
Relay 2
NOTE : A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION. WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT THE WIRES.
5-12
TROUBLE SHOOTING
WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF THE FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE MICROWAVE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.
CAUTIONS
1. Check grounding before checking for trouble. 2. Be careful of the high voltage circuit. 3. Discharge the high voltage capacitor. (See page 2-1) 4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire from these parts and then check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter. 5. Do not touch any part of the circuit on the PCB since static electric discharge may damage this control panel. Always touch yourself to ground while working on this panel to discharge any static charge built up in your body. (Micom model only)
CONDITION
Microwave oven does not work.
CAUSE
Inserting many plugs into one outlet and using them at the same time. (blown fuse or breaker) Microwave oven plug is not inserted tightly.
REMEDY
Avoid using other electrical appliances when you use the microwave oven.
Insert microwave oven plug securely. Use the microwave oven at adequate line voltage. This is not a defect. It is possible that the food should be cooked for a longer time. Do not use metallic ware for cooking except that noted in the cooking guide. Do not use any type of cookware with metallic trimming. 1. Use plastic wrap or lid. 2. Stir once or twice while cooking soup, cocoa or milk, etc.
Sparks occur.
Using metallic ware and allowing it to touch the oven wall. Ceramic ware trimmed in gold or silver powder is used.
Uneven cooking.
5-13
(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.
1. Incomplete segments. Segment missing. Partial segment missing. Digit flickering (NOTE: Slight flickering is normal.) 2. Colon does not turn on or blink. 3. A distinct change in the brightness of one or more numbers in display. 4. One or more digits in the display are not lighting. 5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display. 6. Specific numbers (for example 7 or 9) will not display when key pad is touched. 7. Display does not count down with time blinking or up with clock operation. 8. Display obviously jumps in time while counting down. 9. Display counts down too fast while cooking. 10. Each indicator light does not turn on after setting cooking cycle. 11. Display time of day does not reappear when cooking is finished.
CONDITION
1. No input can be programmed.
CHECK
Check the connection between membrane key assembly and PCB assembly. Replace key membrane assembly and check operation.
RESULT
Continuity
CAUSE
Defective PCB assembly. Loose connection. Defective key membrane assembly. Defective PCB assembly.
REMEDY
Replace PCB assembly. Connect them tightly. Replace key membrane assembly. Replace PCB assembly.
No continuity
2. Some inputs cannot be programmed. 3. Display shows a number or figure different from one touched.
4. Random programming when touching other pads. 5. Display is fixed at some figure and can not accept any input.
5-14
(TROUBLE 2) Oven does not operate at all, Display window does not display any figures, and no input is accepted.
CONDITION
1. Fuse blows.
CHECK
Check continuity of monitor switch (with door closed). Replace fuse Check continuity of primary switch (with door opened).
RESULT
Continuity.
CAUSE
Malfunction of the monitor switch.
REMEDY
Replace fuse, primary, monitor, secondary switches, and RELAY(RY2) of P.C.B Assembly.
No continuity.
Continuity.
No continuity.
Replace fuse, primary, monitor, secondary switches, and RELAY(RY2) of P.C.B Assembly. Replace fuse, primary, monitor, secondary switches, and RELAY(RY2) of P.C.B Assembly. Replace high voltage capacitor. Replace high voltage transformer.
Continuity.
No continuity.
Disconnect one side of the wire lead connected from transformer to the high voltage capacitor and operate the unit.
Normal.
NOTE : All these switches must be replaced at the same time. Refer to page 5-7, 5-8
No continuity.
Defective thermostat.
Replace thermostat.
Continuity.
No continuity.
5-15
(TROUBLE 3) Display shows all figures set, but oven does not start cooking while desired program times are set and START pad is touched. CONDITION
1. Setting time does not count down when touching START pad.
CHECK
Check continuity of secondary switch (with door closed).
RESULT
No continuity.
CAUSE
Defective secondary switch.
REMEDY
Replace secondary switch.
Continuity.
Check the connection between CN1 connector and PCB assembly. 2. Fan motor or oven lamp do not turn on. Check fan motor. Check oven lamp.
Continuity
Replace PCB assembly. Connect them tightly. Replace fan motor. Replace oven lamp.
No continuity
(TROUBLE 4) Oven seems to be operating but little heat is produced in oven load. CONDITION
Output is low
CHECK
Check the power source voltage.
RESULT
Lower than 90% of rating voltage. Normal
CAUSE
Decrease in power source voltage with load.
REMEDY
Suggest customer contact local electric power utility co. or qualified electrician. Replace PCB assembly.
Disconnect the wire leads from relay 2 and check on and off time with multitester.
Abnormal
Normal
Abnormal
Defective magnetron.
Replace magnetron.
NOTE : Simple test of power output-conducted by heating one liter water for one min. if available. Minimum 8.5C temperature rise is normal condition. 5-16
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run. (Display operates properly) CONDITION
No microwave oscillation.
CHECK
Disconnect the wire leads from relay 2 and check continuity of relay 2. (Operate the unit)
RESULT
No continuity.
CAUSE
Defective PCB assembly.
REMEDY
Replace PCB assembly.
Continuity.
Abnormal
Normal
Abnormal
Normal
Abnormal
Normal
Check magnetron.
Abnormal
Defective magnetron.
Replace magnetron.
5-17
CHECK
Heater
RESULT
Abnormal
CAUSE
Malfunction the heater.
REMEDY
Replace
Normal
Wire connection
No continuity
Open or loosen.
Heater
Abnormal
Replace
Normal
Disconnect the wire leads from relay 3 and check continuity relay 3.(Operate the unit)
Abnormal
NOTE : Make sure the wire leads correct position. When Removing the wire leads from the parts, be sure to grasp the connector, not the wires. When removing the magnetron, be sure to install the magnetron gasket in the correct position and in good condition.
Disconnect the wire leads from relay 2 and check continuity relay 2. (Operate the unit)
Abnormal.
5-18
EXPLODED VIEW
INTRODUCTION
INTERIOR PARTS BASE PLATE PARTS DOOR PARTS SUCTION GUIDE MAIN PARTS
6-1
DOOR PARTS
13213A 13581A
14026A
14970A
13720D 13352A
6-2
268771
WTP018
24781M
24510L
24970A 250201
6-3
WTT021
35264A 3112U 348102 33550H 948502 948504 WMT002 35300A 348101 35301A WTT021
WTP013
368771
6-4
55006F
50FZZA WTT028
435001
559001
466002 54974S
6-5
INTERIOR PARTS
WTP004
WSZ002
6-6
50CZZH 34810C
56170D
633021
948501
647781
647781
W067
WTT028
W101
633032
633031
6-7
8-1
8-2