Ti809 07
Ti809 07
30 November 1998
Technical Instructions
Design of Cold-Formed Load
Bearing Steel Systems
and Masonry Veneer / Steel Stud Walls
Headquarters
U.S. Army Corps of Engineers
Engineering and Construction Division
Directorate of Military Programs
Washington, DC 20314-1000
US Army Corps
of Engineers
CEMP-E TI 809-07
30 November 1998
i
CHAPTER 1: INTRODUCTION
Paragraph Page
1. PURPOSE AND SCOPE 1-1
2. APPLICABILITY 1-1
3. REFERENCES 1-1
4. PARTNERING EFFORT 1-1
5. DESIGN CONCERNS UNIQUE TO COLD-FORMED 1-1
6. USES OF COLD-FORMED STEEL 1-3
7. COLD-FORMED SUPPLIERS 1-3
8. RESPONSIBILITIES 1-3
9. MATERIALS 1-5
CHAPTER 2: DESIGN OF COLD-FORMED STEEL
1. INTRODUCTION 2-1
2. PRESCRIPTIVE METHODS. 2-1
3. COLD-FORMED STEEL FRAMING 2-2
4. DESIGN OF STRUCTURAL ELEMENTS 2-5
5. FASTENERS AND CONNECTIONS 2-12
6. USEFUL RELEVANT INFORMATION 2-15
CHAPTER 3: SEISMIC DESIGN GUIDANCE FOR SHEAR WALLS
1. INTRODUCTION 3-1
2. TI 809-04, SEISMIC DESIGN FOR BUILDINGS 3-1
3. STRUCTURAL DESIGN CRITERIA 3-3
4. DEFLECTION AND DRIFT LIMITS 3-3
5. TORSION 3-4
6. COLD FORMED STEEL SEISMIC REQUIREMENTS 3-5
CEMP-E TI 809-07
30 November 1998
ii
Page
7. DIAGONAL STRAP DESIGN 3-5
8. COLUMN DESIGN 3-6
9. CONNECTION DESIGN ASSUMPTIONS 3-9
10. PANEL ANCHORS 3-12
CHAPTER 4: MASONRY VENEER/STEEL STUD WALLS, (NONBEARING
CONSTRUCTION)
1. INTRODUCTION 4-1
2. GENERAL DESCRIPTION OF WALL SYSTEM 4-1
3. REQUIREMENTS FOR WALL COMPONENTS AND DETAILS 4-1
4. WALL SYSTEM DESIGN REQUIREMENTS 4-4
5. WORKMANSHIP 4-7
6. DESIGN EXAMPLE 4-7
APPENDIX A: References
APPENDIX B: Cold-Formed Steel Test Panel Drawings.
APPENDIX C: FEMA 302 and Other Standard Guidance for Cold-Formed Steel
Seismic Design
APPENDIX D: Seismic Design Example
APPENDIX E: Prototype Shear Panels for Cold-Formed Steel Seismic Design
APPENDIX F: Seismic Qualification Procedure and Acceptance Criteria for Other
Shear Panel Configurations
APPENDIX G: Masonry Veneer / Steel Stud Walls (Nonbearing Construction)
APPENDIX H: Metric Conversion Data Sheet.
APPENDIX I. Standard Drawings Cold-Formed Steel
CEMP-E TI 809-07
30 November 1998
iii
FIGURES
Figure Title Page
1-1 Design Process for Load-bearing Cold-formed Steel Systems 1-2
2-1 Typical Cold-Formed Section Symmetries 2-3
3-1 Flowchart for Cold-Formed Steel Shear Panel Seismic Design 3-2
3-2 Schematic of CERL Cold-Formed Steel Shear Panel Model 3-4
4-1 Double Track Slip Joint 4-5
B-1 Prototype 3 Story Barracks B-2
B-2 Shear Wall Test Panel A1 B-3
B-3 Shear Wall Test Panel A2 B-4
B-4 Shear Wall Test Panel D1 B-5
C-1 Design Response Spectrum C-2
D-1 Design Response Spectrum for Fort Lewis Washington
Barracks Building D-18
D-2 Schematic Drawing of Barracks Building Example D-18
D-3 Barracks Building Short Direction and Plan Views D-19
D-4 Example Connection /Anchorage Detail
1
st
Row of Table D-5, D-8 D-17 D-20
D-5 Example Connection /Anchorage Detail
2nd Row of Table D-5, D-8 D-17 D-21
D-6 Example Connection /Anchorage Detail
3rdRow of Table D-5, D-8 D-17 D-22
D-7 Example Connection /Anchorage Detail
4th Row of Table D-5, D-8 D-17 D-23
D-8 Example Connection /Anchorage Detail
5th Row of Table D-5, D-8 D-17 D-24
D-9 Example Connection /Anchorage Detail
6th Row of Table D-5, D-8 D-17 D-25
F-1 Schematic Drawing Showing Sensor Locations F-2
CEMP-E TI 809-07
30 November 1998
iv
Page
F-2 Modified SAC Cyclic Test Time History
with
y
=0.4 in and 6-in/imn Stroke Rate F-4
G-1 Wire Anchors G-2
G-2 Wire Anchor, Details G-3
G-3 Wire Anchor and Continuos Brick Joint Reinforcement G-4
G-4 Pintle Anchor G-5
G-5 Typical Brick Veneer Steel Stud Panel Wall G-6
G-6 Adjustable Wall Anchor Detail G-7
G-7 Masonry Veneer Steel Stud Panel Wall Plan View G-8
G-8 Masonry Veneer Steel Stud Panel Wall Foundation
Wall Section G-9
G-9 Masonry Veneer Steel Stud Panel Wall Structural
Steel Section G-10
G-10 Masonry Veneer Steel Stud Panel Wall Reinforced
Concrete Section G-11
G-11 Masonry Veneer Steel Stud Panel Wall Steel Joist Section G-12
G-12 Slip Joint Details, Typical Single Track G-13
G-13 Slip Joint Details, Typical Double Track G-14
G-14 Slip Joint Details, Parapet Slide Clip G-15
G-15 Bottom Connection, Track Anchored to Concrete G-16
G-16 Expansion Joints, Brick or CMU Veneer Joint G-17
TABLES
Table Title
1-1 Standard Minimum Delivered Uncoated Metal Thickness 1-6
1-2 Fire Rated Assemblies 1-8
2-1 Summary of Prescriptive Methods Limitations 2-1
CEMP-E TI 809-07
30 November 1998
v
Page
2-2 AISI Approved Steels 2-4
2-3 Pipe Openings: Maximum Pipe Opening and
Web Reinforcement 2-10
2-4 Suggested Capacities for Screw Connections 2-12
2-5 Suggested Design Loads for Fillet and Flare-Bevel
Groove Welds 2-13
2-6 Suggested Capacity for Expansion Anchors in Concrete 2-13
2-7 Suggested Capacity for Power Driven Fasteners in Concrete 2-14
2-8 Suggested Capacity for Power Driven Fasteners in
Structural Steel 2-14
2-9 Joist End Clip: Allowable Loads 2-14
3-1 Design Coefficients and Factors for Basic
Seismic-Force-Resisting Systems 3-3
3-2 Allowable Story Drift,
a
3-3
3-3 Maximum Column-to-Anchor Weld Thickness 3-13
3-4 Maximum Angle Thickness Based
on Column-to-Anchor Weld Thickness 3-13
C-1 Occupancy Importance Factor C-1
C-2a Values of F
a
as a Function of Site Class and Mapped
Short-Period Maximum Considered Earthquake
Spectral Acceleration C-1
C-2b Values of F
v
as a Function of Site Class and Mapped
One-second Period Maximum Considered Earthquake
Spectral Acceleration C-2
C-3a Seismic Design Category Based on Short Period
Response Accelerations C-3
C-3b Seismic Design Category Based on One-second Period
Response Acceleration C-3
C-4 Coefficient for Upper Limit on Calculated Period C-7
CEMP-E TI 809-07
30 November 1998
vi
Page
D-1 Earthquake Ground Motion Definition Summary
for Fort Lewis D-1
D-2 Barracks Building Weight Calculations D-3
D-3 Short Duration Lateral Seismic Force Calculations
for the Barracks Building D-5
D-4 Long Direction Lateral Seismic Force Calculations
for the Barracks Building D-7
D-5 Diagonal Strap Design in the Short Direction D-8
D-6 Gravity Load Calculations D-9
D-7 Trial Stud Sizes and Quantities for One
Short-Direction Frame D-9
D-8 Column Design for Cold-Formed Steel Shear Panels
Barracks Example D-10
D-9 Column Capacity Calculations for Shear Panels
Barracks Example D-10
D-10 Column Intermittent Weld Design, Combined Axial
and Moment Capacity D-11
D-11 Column and Anchor Shear Design D-12
D-12 Screwed Connection Design D-12
D-13 Screwed Connection Rupture Strength and
Welded Connection Design D-14
D-14 Shear Panel Anchor Angle and Plate Design D-15
D-15 Shear Panel Anchor Angle and Plate Design (Continued) D-16
D-16 Anchor Moment and Anchor Bolt Shear Design D-16
D-17 Anchor Bolt Tensile and Cone Failure Design D-17
E-1 Prototype Shear Panel Load Capacities E-1
F-1 Format for Tabular Coupon Test Results F-1
F-2 Cold-Formed Steel Shear Panel Instrumentation F-3
F-3 Cyclic Test Load Protocol F-4
CEMP-E TI 809-07
30 November 1998
vii
Page
F-4 Summary of Test Panel Performance F-5
F-5 Acceptance Criteria for Shear Panels Based on , ,
1
F-6
F-6 Values for R,
0
and C
d
F-6
CEMP-E TI 809-07
30 November 1998
TECHNICAL INSTRUCTIONS
Design of Cold-Formed Load
Bearing Steel Systems
and Masonry Veneer / Steel Stud Walls
Any copyrighted material included in this document is identified at its point of use. Use of the copyrighted material
apart from this document must have the permission of the copyright holder.
Approved for public release; distribution is unlimited.
Record of Changes (changes indicated \1\/1/)
No. Date Location
Supersedes: ETL 1110-3-439 Masonry Veneer/Steel Stud Walls (Nonload-bearing Construction)
CEMP-E TI 809-07
30 November 1998
FOREWORD
These technical instructions (TI) provide design and construction criteria and apply to all
U.S. Army Corps of Engineers (USACE) commands having military construction
responsibilities. TI will be used for all Army projects and for projects executed for other
military services or work for other customers where appropriate.
TI are living documents and will be periodically reviewed, updated, and made available
to users as part of the HQUSACE responsibility for technical criteria and policy for new
military construction. CEMP-ET is responsible for administration of the TI system;
technical content of TI is the responsibility of the HQUSACE element of the discipline
involved. Recommended changes to TI, with rationale for the changes, should be sent
to HQUSACE, ATTN: CEMP-ET, 20 Massachusetts Ave., NW, Washington, D.C.
20314-1000.
TI are effective upon issuance. TI are distributed only in electronic media, primarily
through the TECHINFO http://www.hnd.usace.army.mil/techinfo/index.htm Internet site and the
Construction Criteria Base (CCB) http://www.ccb.org/ maintained by the National Institute of
Building Sciences at Internet site. Hard copies of these instructions produced by the
user from the electronic media should be checked against the current electronic version
prior to use to assure that the latest instructions are used.
FOR THE COMMANDER:
Dwight A. Beranek, P.E.
Chief, Engineering and Construction Division
Directorate of Military Programs
CEMP-E TI 809-07
30 November 1998
1-1
CHAPTER 1
INTRODUCTION
1. PURPOSE AND SCOPE. This document provides design guidance on the use of cold-formed steel
systems for both load-bearing (Chapter 2) and nonload-bearing (Chapter 4) applications. Also, criteria
are provided to use load-bearing systems in shear wall (Chapter 3) applications. The nonload-bearing
application guidance in Chapter 4 also includes provisions for the masonry wythe and moisture
protection of complete masonry veneer/steel stud curtain wall systems.
2. APPLICABILITY. These instructions are applicable to all elements responsible for the design of
military construction. Exceptions to this criteria will require Corps of Engineers Headquarters (CEMP-
ET) approval.
3. REFERENCES. Appendix A contains a list of references used in these instructions.
4. PARTNERING EFFORT. This document is the result of partnering between industry and
Government with emphasis on Green Building Technology. Designers should require materials,
products and innovative construction methods and techniques which are environmentally sensitive,
take advantage of recycling and conserve natural resources. Funding for this effort came from the
Green Building Program.
5. DESIGN CONCERNS UNIQUE TO COLD-FORMING.
a. General. The AISI Specification is applicable to sheet and strip steels with thicknesses of 6.35
mm ( in) or less, but steel plates and bars up to 25.4 mm (1 in) can successfully be used as structural
shapes. Designers working with cold-formed steel products will account for several unique conditions
not normally found in AISC steel designs as outlined below:
Effective section properties are based on the design stress of the loading condition being
analyzed,
Lateral-torsional buckling is a special buckling condition unique to the cold-formed design
of compression members,
Local buckling of section elements, and the lateral buckling of members is different than
typically found in AISC steel design,
Connections can be assembled using welds, screws, or bolts. Crimping is not allowed as
well as powder driven pins. However, powder driven pins can be used to attach wall tracks
to concrete floors, foundations, and steel superstructures,
A Deign Process for Load-bearing Cold-Formed Steel Systems Flowchart is shown as
Figure 1-1.
b. Seismic Design The seismic design guidance provided in Chapter 3 will only be used for
Performance Objective 1A (Life Safety Performance Objective Level defined in TI 809-04) for all
seismic ground motion levels and enhanced Performance Objectives (2A, 2B and 3B) for Seismic
Design Categories A and B. The definition of performance objectives and seismic design categories
are provided in TI 809-04, Seismic Design for Buildings.
Seismic design with cold-formed steel has two inherent problems with the material itself. The first is
light gauge thickness of the cold-formed steel materials and the second is the material strength
variability. The objective of seismic design guidance is to ensure ductile building system performance
in the large seismic event and elastic response in the small event or wind loading. Ductile building
performance
CEMP-E TI 809-07
30 November 1998
1-2
requires that selected ductile components yield, but continue to carry loads and absorb energy through
significant plastic response. At the same time potentially brittle failure modes, such as column buckling
or connection failure must be prevented. The design challenge for cold-formed steel is to ensure that
building components, and in particular shear panel components, be proportioned
CEMP-E TI 809-07
30 November 1998
1-3
Select Structural System
Determine Loadings
-Gravity
-Wind
-Earthquake
-Other
TI 809-01
AISI - Section A
ASCE 7
No Earthquake:
Proportion Members Using
ASD or LRFD
(Don't Mix Methods)
Earthquake: Proportion
Members Using LRFD Only
Determine Design
Occupancy
TI 809-04
Analyze Ground Motion
TI 809-04
Analyze Structure Using
Equivalent Force Procedure
TI 809-04
Select Preliminary Size of
Members
TI 809-07- Chapter 2, 3
and 4
AISI - Cold-Formed Steel
Design Manual
Calculate the Effective
Section Proporties for
Structural Members
TI 809-07- Chapter 2 and 3
AISI - Section B
Select Member
Calculate Load Capacity of
Structural Memebers
AISI - Section C or D
Design Connections
AISI - Section E
TI 809-07-Chapter 2, 3 and 4
Select Bracing or Stiffener
AISI Section C or D
Check
-Floor.Vibrations
-Drift Limits
-P. Limits
TI 809-07- Chapter 2
Check Member Buckling
-Local
-Lateral
--Lateral.Torsional
-Web Crippling
AISI Section C or D
Size Diagonal Bracing for
Gravity Loads
-Stiffness
-Strength
TI 809-07- Chapter 2 and 3
AISI - Report CF 93-1
AISI - RG 9518
AISI - RG 9604
Figure 1-1: Design Process for Loadbearing Cold-Formed Steel Systems
OK
Inadequate
More Than Allowed
Layout Selected Structural
Members
OK
Select New Stuructural
Member
CEMP-E TI 809-07
30 November 1998
1-4
relative to each other and detailed to ensure the ductile response. In this guidance, this is
accomplished by ensuring that the diagonal straps yield and respond plastically through significant
displacement, without risk of damage to brittle connections or column buckling.
Seismic design guidance is provided on three levels:
Tabular data for prototype shear panels in terms of the maximum story shear and maximum
and minimum gravity load. These terms are defined in Chapter 3 and the shear panel
configurations and data are provided in Appendix E.
Detailed guidance for shear loads using shear panels with diagonal straps as primary lateral
load resisting element. This guidance is provided in Chapter 3, with background guidance
taken from other sources in Appendix C and an example problem illustrating the guidance in
Appendix D. The Error! Bookmark not defined., Error! Bookmark not defined. program
used in the example problem is available as a design tool for shear panel design.
A test procedure and the acceptance criteria for other shear panel configurations is provided in
Appendix F.
6. USES OF COLD-FORMED STEEL.
a. General. Cold-formed steel systems have been used in industry and within the government
for many decades. The primary areas of usage include: standing seam roof systems, doors, roof and
floor joists, decking and floor systems, ventilation and ceiling systems, interior wall partitions and
exterior fascia, metal buildings, lighting poles, guardrail, and corrugated steel pipe. These TI provide
guidance necessary for designers to develop loadbearing steel systems.
b. Steel Framing Systems. These systems can be used in: wall, floor, and roof trusses of low
rise offices, single family homes, and multi-family housing structures. Cold-formed systems should be
galvanized for the local environmental conditions, and be pre-punched for routing utility services
through walls. A rubber or plastic grommet must be provided in each pre-punched hole that utilities are
passing through to prevent corrosion between dissimilar metals in the wall stud cavity.
7. COLD-FORMED SUPPLIERS. Cold-formed manufacturers perform the following services for the
commercial customers: provide framing details, develop design information on the structural capacity
of their members, help specify the jobs materials, and deliver precut materials. Government designers
should specify the design properties of each structural member; studs, track, heads, jambs, jack studs,
etc. These properties include member depth, width and design thickness for each section.
8. RESPONSIBILITIES
a. Designers. Cold-formed steel framing involves the use of engineered products outlined in an
overall engineered system. Cold-formed steel framing is ideally suited for structural applications such
as curtain wall framing, load-bearing wall framing, floor framing, rigid frames, trusses, and roof rafter
framing.
(1) Selecting Member Strength. Designers are responsible for specifying which
products are to be used as well as which standards the products must meet. The
products must meet all of the design requirements which normal engineering practice
requires. Axial load capacity of compression members, flexure, torsion, shear, and web
crippling in beams, and combined stresses in columns, etc. must be examined.
Designers are to specify all materials by nominal uncoated thickness, effective
section properties, and member loads. Loads should include moment and shear
diagrams, and axial load with eccentricity.
CEMP-E TI 809-07
30 November 1998
1-5
All connections (member-to-member and member-to-structure) are to be
examined carefully taking into account all relevant physical strengths and
properties as well as proper transfer of all loads to the supporting structure.
Design selected walls to provide frame stability and lateral load resistance.
Engineered methods such as diaphragm shear walls or diagonal steel strapping
are used to provide frame stability and transfer lateral loads through the
structure into the foundation. Provide additional studs as required to resist the
vertical component of the loads from the diagonal bracing.
Wall bridging is designed to provide resistance to minor axis bending and
rotation of studs.
Diaphragm rated components can be substituted for bridging; however, they
must be installed prior to loading of the wall. If components are installed on
one side of the wall only, then the flanges on the other side of the studs must
be bridged with suitable bridging. Bridging can be removed or left in place
when diaphragm rated components are installed.
Provide for structure movement as indicated and necessary by design or code
requirements.
(2) Member Specification. The primary specification for the design of the individual
components is the AISI Specification for the Design of Cold-Formed Steel Structural Members. Other
considerations, which the designer specifies, include:
Member or Stud size, spacing, and depth.
Deflection criteria, maximum spacing, minimum gage, wind loads.
Studs are spaced to suit the design requirements and limitations of collateral
materials.
Allow for additional studs at panel intersections, corners, doors windows,
control joints, etc.
b. Manufacturers. Lightweight steel framing involves the use of engineered products in an
engineered system. Manufacturers provide technical product information, including physical and
structural properties, and manufacturing standards that the designer can use to specify the appropriate
structural products.
Samples. Samples are representative pieces of all framing component parts and
accessories;
Certification. Certification is a statement from the manufacturer certifying that the
materials conform to the appropriate requirements as outlined in the contract documents;
c. Contractor. The Contractor is responsible for providing the finished structure in strict
compliance with the contract documents and cold-formed steel shop drawings. Included in
the contractors responsibilities are the following:
Shop Drawings of details and attachments to adjoining work.
Drawings showing plans, elevations, sections, and details.
shop coatings
steel thickness
size, location, spacing of fasteners for attaching framing to itself
details of attachment to the structure
accessories and their installation
and critical installation procedures
d. Contractor Quality Control. The Contractors Quality Control (CQC) Manager inspects Corps
of Engineers projects. This effort outlines the contractors inspection document requirements. The
following Quality Assurance Documents are to be maintained by the CQC Manager:
The manufacturer and product delivery dates,
CEMP-E TI 809-07
30 November 1998
1-6
the contractors staff and qualifications,
compliance to testing standards for members, erection tolerances, and fasteners,
submittal registers, erection drawings, production drawings,
designer of record approvals, and CQC inspection reports,
designer of record notes to the field on handling, storage, installation and special
inspections by design engineering staff during construction,
designer of record limitations and permissible deviations,
qualifications of field welders,
process for getting designer of record approval for applying attachments to metal
stud systems,
final inspection and approval of framing systems (this could be accomplished through
the local building code group).
9. MATERIALS. The marking standard used in the following material does not have a metric
equivalent. Materials marked to the following standard are for field acceptance of the delivered
materials. Designers are to use the nominal uncoated material thickness as shown on the drawings
and within the specification.
a. Markings. The Metal Lath / Steel Framing Association (ML/SFA), Metal Stud Manufacturers
Association (MSMA), the AISI Residential Advisory Group (RAG), and the Prescriptive Standard for
Steel Framing, accepted by the Council of American Building Officials (CABO), have adopted a
standard method of marking all cold-formed steel members. The markings will be on the web of the
section and will be repeated throughout the length at a maximum of 1219 mm (48 inches) on center.
There is no defined size or method of marking, but the markings must be legible and easily read. The
product marking will include the following information:
(1) Manufacturer identification. Manufacturers Name, Company Logo or emblem will be
displayed to clearly identify the product manufacturer.
(2) Minimum delivered uncoated steel thickness. Material thickness without coatings or
galvanizing is represented in mils of the decimal thickness value for example 0.84 mm (33 mil);
(3) Protective coating designator. The galvanizing coat designator will indicate the
amount level of protection being provided such as: G-40-EQ, G-60-EQ, or G-90-EQ, where EQ is an
equivalent protective coating to the designated galvanized coating.
(4) Minimum yield strength. Material strength in kips per square inch (ksi)
b. Nomenclature.
(1). Standard Nomenclature for Manufacturers Catalogs:
(a) The first set of numbers will represent the depth of the section to two decimal
places without the use of a decimal point.
(b) A Letter following the depth of the section will define the shape of the section per
the following:
S = CEE shaped Stud
U = Channel shaped Stud
T = Track
F = Furring Channel
(c) The second set of numbers will represent the flange width to two decimal places
without the use of a decimal point.
CEMP-E TI 809-07
30 November 1998
1-7
(d) The last set of numbers will be the minimum delivered
thickness in mils and be preceded by a dash (-).
Example: 362S162-33 = 92 mm (3-5/8) CEE Stud with a 41 mm (l-5/8) Flange 0.84 mm (33 mils)
Thickness
(2) Standard Minimum Delivered Uncoated Metal Thicknesses are shown in Table 1-1:
Table 1-1: Standard Minimum Delivered Uncoated Metal Thickness
Nominal / Design Thickness Minimum / Delivered Thickness
Gage Soft Metric Decimal Soft Metric Decimal Mils
26 0.437 mm 0.0172 0.414 mm 0.0163 16
25 0.478 mm 0.0188 0.455 mm 0.0179 18
22 0.719 mm 0.0283 0.686 mm 0.0270 27
20 0.879 mm 0.0346 0.836 mm 0.0329 33
18 1.146 mm 0.0451 1.087 mm 0.0428 43
16 1.438 mm 0.0566 1.367 mm 0.0538 54
14 1.811 mm 0.0713 1.720 mm 0.0677 68
12 2.583 mm 0.1017 2.454 mm 0.0966 97
10 3.150 mm 0.1240 2.997 mm 0.1180 118
From ICBO: Acceptance Criteria for Steel Studs, Joists, and Tracks, AC46, April 1998.
(3) Standard Flange and Return Lips for CEE Studs:
0.46 mm & 0.69 mm (18 & 27 Mil) minimum thickness = 32 mm (1-1/4) Flange with
4.8 mm (3/16) Lip.
Any Thickness = 35 mm (1-3/8) Flange with 9.5 mm (3/8) Lip.
Any Thickness = 41 mm (1-5/8) Flange with 13 mm (1/2) Lip.
Any Thickness = 51 mm (2) Flange with 16 mm (5/8) Lip.
Any Thickness = 64 mm (2-1/2) Flange with 16 mm (5/8) Lip.
(4) Standard Track Flange Sizes: 25 mm (1), 32 mm (1-1/4), 38 mm (1-1/2) and 51 mm
(2)
(5) Standard U Channels: Web x Leg x Minimum Thickness
29 mm (3/4) x 13 mm (l/2) x 1.37 mm (54 Mil)
38 mm (1-1/2) x 13 mm (1/2) x 1.37 mm (54 Mil)
51 mm (2) x 13 mm (1/2) x 1.37 mm (54 Mil)
(6) Standard Hat Furring Channels: Depth x Minimum Thickness
22 mm (7/8) x 0.46, 0.69,0.84, 1.09 mm (18, 27, 33, and 43 Mil)
38 mm (1-1/2) x 0.46, 0.69,0.84, 1.09 mm (18, 27, 33, 43, and 54 Mil)
c. Strain Hardening.
1. General. The cold working of steel stresses it beyond its elastic limit and leaves a
residual strain. After the cold working, the steel has an increased yield stress. This process of raising
the yield stress is known as cold working. The amount of strain hardening is relative
to the amount of cold working. In normal roll forming, the cold working is nominal, the steel remains
ductile and it makes a modest improvement in the allowable stress of the section. Extensive cold
working of steel can cause it to loose its ductility and become brittle, but normally, this condition is not
associated with common roll formed products.
2. Cold Reducing and Rerolling of Steel. Steel mills have the capability to cold reduce the
steel sheet to meet the specified thickness before shipment to the manufacturer. Some manufacturers
can reroll the steel sheet to again reduce the sheet thickness. Within the AISI Specification this is
CEMP-E TI 809-07
30 November 1998
1-8
known as Other Steel. This practice is allowed by the AISI Specification if the rerolled steel meets the
ductility criteria of the AISI Section A3.3. Therefore, the manufacturer is strain hardening the material.
Depending on the degree of rerolling that occurs, the material will have a higher steel yield strength,
less ductility, and a more rounded stress-strain curve above the yield point of the steel than would be
seen in the virgin steel sheet materials. Design guidance that is provided in chapter 3 recognizes this
material property variability. Diagonal bracing materials are to be ASTM A653 steel without rerolling,
and will be a Category I submittal for approval by the designer of record.
d. Damaged Materials.
(1) General. Steel framing materials can be rejected for the following reasons: physical
damage (dents, cuts, twists, buckles); corrosion; length; metal thickness; yield stress; protective coating
or forming. Physical damage and corrosion are easily identified. Length variations and forming
problems are relatively easy to identify with standard measuring devices. The metal thickness must be
checked with a micrometer and one must know what the required thickness should be. The yield
strength and protective coating can only be checked through testing.
(2) Tolerances and Coatings. The allowable physical tolerances and standard protective
coatings for steel framing products can be found in current ASTM Standards. ASTM C-645 covers
tolerances and standard protective coatings for nonstructural partition framing and ASTM C-955 covers
the same information for structural framing. The yield strength for structural framing is normally
specified in the project specifications or on the drawings. Special protective coating requirements are
also specified in the project specifications.
e. Fire Resistance Rating.
(1) General. Fire rating of assemblies denotes a length of time that a given assembly will
resist fire penetration under controlled laboratory conditions; Table 1-2 lists many Fire Rated
Assemblies. These fire-rating tests are performed in accordance with the existing consensus standards
of ASTM or ANSI. A fire rating is only valid for the tested assembly. Although most materials cannot
be added or changed in a fire rated assembly, stronger steel framing sections can be used. The
specified depth and gauge of steel framing in a tested assembly are considered minimums. The fire
rating will still apply to the assembly when steel framing members that are deeper and/or heavier than
the specified members, are used.
(2) Fire Tests. There are numerous fire rated assemblies for interior walls, exterior walls,
floors, ceilings, and roofs, incorporating steel framing. Various laboratories throughout the country have
performed fire rating tests of loadbearing steel stud walls. Currently, within the AISI Residential
Advisory Group (RAG), a task group has been assigned to compile a listing of all available fire rated
assemblies, using steel framing. The following sources list many fire rated assemblies that can be
used if cold-formed design.
Fire-Resistance Ratings of Load-Bearing Steel Stud Walls (AISI, Publication Z-4)
Fire Design Manual (Gypsum Association)
CEMP-E TI 809-07
30 November 1998
1-9
Table 1-2: Fire Rated Assemblies
The following table depicts various fire rated assemblies incorporating steel framing components.
Test Reference Fire Rating Type of Assembly Agency Components
FM 24676.4
FC 224
2 HR Floor/Ceiling FM 1975 -64 mm (2 ) concrete (note B)
-14 mm (9/16) 0.36 mm (28 GA) deck and
mesh
-184 mm (7 ) X 1.15 mm (18GA) joists,
610 mm (24) OC
-2 layers 16 mm (5/8) G.W.B. ceiling
FM 29135
FC 245
1 HR Floor/Ceiling FM 1977 -51 mm (2) concrete
-41 mm (1 5/16), 0.56 mm (24 GA) deck
-152 mm (6) X 1.15 mm (18 GA) joists,
610 mm (24) OC
-1 layer 13 mm () G.W.B. ceiling
L 524 1 HR Floor/Ceiling UL 1988 -Min 184 mm (7 ) X 1.15 mm (18 GA),
steel stud, 610 mm (24) OC
-Use any of the floor systems indicated in
the UL test
P 511 1 HR Roof/Ceiling UL 1988 -Min 184 mm (7 ) X 1.15 mm (18 GA),
Steel Joist, C Shape, 51 mm (2) Flange
Minimum, 610 mm (24 OC)
-See test for roof/ceiling components
P 512 1 HR Roof/Ceiling UL 1988 -Min 184 mm (7 ) X 1.15 mm (18 GA),
Steel Joist, C Shape, 610 mm (24) OC
-See test for roof/ceiling components
U 418 HR Bearing Wall UL 1988 See test
U 418 1 HR Bearing Wall UL 1988 -2 layers 13 mm () thick, G.W.B, one
side
-89 or 140 mm (3 or 5 ) X 1.15 mm
(18 GA) steel stud, 610 mm (24) OC
-See test for exterior component
U 418 2 HR Bearing Wall UL 1988 -3 layers 13 mm () thick, G.W.B, one
side
-89 or 140 mm (3 or 5 ) X 1.15 mm
(18 GA) steel stud, 610 mm (24) OC
-See test for exterior component
U 425 , 1 HR Bearing Wall Interior UL 1988 See test
U 425 1 HR Bearing Wall Interior UL 1988 -2 layers 13 mm () thick, G.W.B, each
side
-89 mm (3 ) X 0.87 mm (20 GA) steel
stud, 610 mm (24 OC)
U 425 2 HR Bearing Wall Interior UL 1988 -3 layers 13 mm () thick, G.W.B
-89 mm (3 ) X 0.87 mm (20 GA) steel
stud, 610 mm (24) OC
U 425 , 1, 1 HR Bearing Wall Exterior UL 1988 See test
U 425 2 HR Bearing Wall Exterior UL 1988 -3 layers 13mm () thick, G.W.B, interior
side
-89 mm (3 ) X 0.87 mm (20 GA) steel
stud, 610 mm (24) OC
-See test for exterior component
U 426 3 HR Bearing Wall UL 1988 -4 layers 13 mm () thick, G.W.B, each
side
-89 mm (3 ) X 0.87 mm (20 GA) steel
stud, 610 mm (24) OC
U 434 1 HR Bearing Wall UL 1988 -1 layer 16 mm (5/8) thick, G.W.B, interior
side
-89 mm (3 ) X 0.87 mm (20 GA) steel
stud, 610 mm (24) OC
-22 mm (7/8) thick Portland Cement
Plaster
Notes:
A: UL denotes Underwriters Laboratories, Inc., and FM denotes Factory Mutual Research Corporation.
B: Lightweight concrete measured from top flute of deck.
CEMP-E TI 809-07
30 November 1998
4-1
CHAPTER 4
MASONRY VENEER/STEEL STUD WALLS
(NONBEARING CONSTRUCTION)
1. INTRODUCTION. This chapter defines the criteria to be used when designing curtain wall masonry
veneer on steel studs. These walls are to be designed to resist out-of-plane lateral loads due to wind and
seismic forces. Also, the wall system must collect, direct and remove water from the wall cavity to
properly control moisture, prevent efflorescence, and control corrosion of the steel system. These curtain
wall steel stud systems will not carry building dead or live loads, nor provide lateral resistance to the
building system.
2. GENERAL DESCRIPTION OF WALL SYSTEM. This wall system consists of a masonry veneer
exterior wythe connected by anchors to a steel stud backup wall. The steel studs will be mechanically
braced until the sheathing and wallboard are placed on the studs. Sheathing is placed on the cavity face
of the stud and the wallboard material is placed on the inside face of the studs. A cavity space is
provided between the masonry veneer and the steel stud wall to allow moisture to migrate down the
inside face of the cavity, brace the masonry veneer laterally and transfer the horizontally applied loads to
the steel studs. The masonry wythe will be isolated on three sides to assure that it will only carry its own
weight.
3. REQUIREMENTS FOR WALL COMPONENTS AND DETAILS. See Appendix G for typical Masonry
Veneer / Steel Stud details.
a. Masonry Wythe.
(1) Masonry Units. Dimensional and physical requirements of the masonry units are
given in TM 5-809-3/NAVFAC DM-2.09/AFM 88-3, Chapter 3. Masonry units used in veneer
walls will be solid.
(2) Mortar. Four types of mortar are specified in ASTM C270, they are M, S, N, and O.
While Types S and N may be used for masonry veneer systems; Type S mortar has higher
strength and good workability and can be used above and below grade, Type N has a lower
strength, better workability is more water tight and can only be used above grade. The lower
strength of Type N mortar allows cracking in the masonry wythe at relatively low load levels.
Masonry cracking will result in more uniformly distributed anchor forces. Conversely, vertical
beam action of the uncracked masonry wythe causes nonuniform distribution of loads to the wall
anchors. Those wall anchors near the top of the uncracked masonry wythe have much higher
loads than those in the lower half of the wythe. Type S mortar is recommended for the design of
masonry veneer steel stud systems. Two strength properties of mortars are measurable: the
bond strength in accordance with ASTM C 1072 and the compressive strength in accordance with
ASTM C 780. Of these two strengths bond is more important in veneer walls and compression is
more important in bearing walls. Type S mortar has the highest compressive and bond strengths
and can be achieved with either portland cement-lime or masonry cement. However, since
masonry cements include premixed workability and air-content additives the bond strengths are
reduced. In order to achieve good bond strengths the maximum air-content of the cement must
be limited to 12 %. Since every manufacturer of masonry cement uses different additives and a
different air-content, care should be used when specifying masonry cements for veneer walls. To
assure a bond strength comparable to a portland cement lime mortar, a comparative bond
strength test between the masonry cement proposed for the job and a corresponding type of
portland cement mortar needs to be completed to demonstrate equivalent or better bond and
compressive strengths for the masonry cement mortars. The contractor will be required to
perform the ASTM C 1072 and C 780 tests on their proposed mortars. Masonry units for the
bond strength test will be the same as proposed for the project.
CEMP-E TI 809-07
30 November 1998
4-2
(3) Masonry Base Details. The base of the masonry wythe must be placed on a shelf
angle or a foundation ledge that is lower than the base channel of the steel stud wall by at least
102 mm (4). The width of this shelf angle or a foundation ledge will include the width of the
masonry wythe and the cavity. This width will not be less than two thirds of the unit thickness
plus the minimum air space. Masonry units set on shelf angles may use a formed lip to reduce
the depth of the horizontal joint that is created at the shelf angle line.
b. Steel Studs and Framing. Designers specifying cold-formed studs and framing will use a
minimum base metal thickness of 1.21 mm (0.0478) and not refer to the metal thickness as 1.146 mm
(0.0451). While the base metal thickness is to be specified to match the design, designers can use table
1-1 as a guide to selecting commonly referred base metal thickness. Designers should be aware that the
minimum delivered thickness specified for steel studs will be no less than shown in table 1-1 when
materials are specified to the minimum design thickness and delivered in accordance with AISI. The
minimum depth of members will be 89 mm (3-1/2) and the minimum flange width of 35 mm (1-3/8) will
have a minimum return lip of 6.4 mm (1/4). Shop drawing submittals will need to present the calculations
that show the effective flange, with the return lip provided. The actual required stud depth, thickness and
spacing will be determined prior to completion of the contract documents. In some cases, the use of a
minimum stud depth of 152 mm (6) yield a more efficient design. Steel studs and framing will be hot-
dipped galvanized metal with a minimum ASTM A 653, G60 coating.
(1) Welding. Welding of steel studs requires the use of qualified welders experienced in
the welding of cold-formed steel. When welding is used, the contractor needs to provide
Qualification documents for each welder working on the project. Welded connections to steel
framing members will be touched-up with zinc-rich paint after welding. Normally welded
connections are not required in curtain-wall construction but may be used for attachments.
(2) Connections. Connections of studs to runners and other framing members will be
made with screws or welds. When the thickness of the thinner connected parts is less than 4.8
mm (3/16) the capacity of the connected parts will be in accordance with AISI. For bolted
connections when the thickness of the thinner material is equal to or greater than 4.8 mm (3/16)
use AISC. Normally the minimum top and bottom channel connections in curtain-wall
construction will require a single #10-16 self-drilling, self-tapping screw in each flange of the
bottom runner for either system and the top channel of the double track system. Welding of studs
may be used in lieu of screws or bolts. Slide clip connections will be used when parapets extend
above the roof line of the structure. These slide clips connectors need to be welded to a
structural element and the details and the capacity of the manufacturers system will need to be
included in the shop drawing review. The minimum edge distance of shot-in anchors for top and
bottom runners to concrete is 76 mm (3) and the minimum fastener spacing is 102 mm (4).
Contract plans will show anchorage details of the steel studs and other framing members to the
building structural system, and the extra steel stud wall framing members required around
openings. The required strength capacities of framing weld and screw connectors will be in
accordance with ML/SFA 540-87 and ML/SFA 920-91.
(3) Openings. Window and door frames will be attached to the steel stud system, not
the masonry veneer.
(4) Top Track and Bottom Runner. A single track or double track top (slip joint)
connection will be used at the top of stud walls to permit the vertical movement of the structural
framing system to prevent the loading of the steel studs. Both flanges of the steel stud will be
attached to the inside top channel for the double track system and the bottom runner of either
system. Mechanical bracing of the single track systems should be installed in addition to support
for all studs. This brace will be placed 305 to 457 mm (12 to 18) from the bottom of the top
channel track.
(5) Parapets. When parapet walls extend above the roof line a slip clip connection will
be used to allow for structural deflections without loading the steel stud system.
CEMP-E TI 809-07
30 November 1998
4-3
c. Sheathing. Fire and water resistant gypsum board sheathing encased in water-repellent paper
on both sides and on the long edges will meet the requirements of ASTM C 79. Other materials may be
used as sheathing when supported by satisfactory performance data. All gaps in the sheathing resulting
from cuts, corners, joints and machine end cuts of the sheathing and all joints at the interface of the
sheathing with dissimilar materials such as floor slabs, doors, windows, and other locations where the
water-resistant membrane terminates will be taped or filled with an exterior rubber-based caulk. The base
detail of the exterior sheathing will be designed to resist water infiltration and the caulking will be applied
to form joints that are complete and continuous. Enough connections of the sheathing to the steel studs
to provide lateral support for the studs in the direction parallel to the plane of the wall will be required. All
screw attachments through the exterior sheathing must resist air and water infiltration.
d. Veneer Anchors. Veneer anchors will be attached through the sheathing to the steel studs.
All steel components of anchors will be stainless steel or hot-dipped galvanized steel. Anchor wires will
be a minimum of 4.8 mm (3/16) diameter. There will be one anchor for each 0.19 m
2
(2 ft
2
) of wall area
and anchors will be spaced no further apart than 610 mm (24). The load-deflection stiffness criteria of
each veneer anchor, applies to direct loads in both tension and compression, and will be not less than
350 N/mm (2000 lbs/in). The design load of the anchor will be the controlling wind load on the stud
tributary width times one-half the vertical span of the stud. The controlling wind load will be the lesser of
the design wind load or the wind load that causes masonry cracking. This load will then be used to
calculate the required anchor capacity. Anchors will have a maximum play or not more than 1.59 mm
(1/16). Synthetic rubber washers will be used under tie connector plates. A clutch torque slip screw gun
will be used to eliminate stripping of threads. Additional anchors will be installed within 305 mm (12) of
the free edges of veneer panels and at the edges of wall openings at the normal spacing. Additional
anchors required around openings will be detailed on the contract drawings.
e. Fasteners. Screw connectors for stainless steel anchors will be stainless steel. Screws for
galvanized anchors will be hot-dipped galvanized.
f. Moisture Barrier. A water-resistant membrane will be placed over the exterior sheathing. The
membrane will be 67 N (15 lbs) roofing felt or similar material, such as: Tyvek building wrap by Dupont
or Barricade building wrap by Simplex. The barrier material will be shingled with each sheet lapping
over the sheet below with a minimum 152 mm (6) lap. Sheets will be lapped a minimum of 152 mm (6)
at vertical joints. The moisture barrier must not be a vapor barrier that will trap water in the stud space of
the wall.
g. Vapor Retarder. A 0.15 mm (6-mil) vapor retarder as required in the ROUGH CARPENTRY
guide specification will be provided on the warm side of the insulation. In most geographical areas the
vapor retarder will be located between the interior wall board material and the face of the steel studs. In
hot humid areas of the United States including the Gulf coast, Florida, coastal Georgia, North Carolina,
South Carolina and Virginia, the vapor retarder should be located between the exterior sheathing and the
steel studs. Check local practice and the recommendations for the installation of insulation and vapor
retarders at the project location. The building designers should perform a condensation analysis of the
wall system used to determine the dew point location within the wall were condensation might be
expected occur.
h. Flashing. Copper or stainless steel through-wall flashing as required in the SHEET
METALWORK, General guide specification will be used. Flashing must be designed, detailed and
constructed so that all water entering the cavity is directed out through weep holes. Ends and sill flashing
must be lapped and sealed at joints. Ends will be turned up at sills and heads. Flashing must also be
turned up behind the moisture barrier a minimum of 152 mm (6) and will be attached to the sheathing.
Flashing must extend to the exterior face of the masonry wall. Weep holes as described herein will be
provided.
i. Shelf Angles. Shelf angles will be hot-dipped galvanized structural steel members. Angles will
be provided in segments, approximately 3.1 m (10) in length, with gaps between segments. Shelf angles
CEMP-E TI 809-07
30 November 1998
4-4
will be detailed to allow enough gaps for thermal expansion and contraction of the steel in angle runs and
at building corners. Corners of buildings will have corner pieces with each leg no less than four 1.2 m
(4) in length where possible. Any areas that are welded will be touched-up with a zinc-rich paint.
j. Cavity. A cavity space of 51 to 102 mm (2 to 4) will be provided between the masonry veneer
and the exterior sheathing or, if insulation is used over the sheathing, between the masonry veneer and
the insulation. In all situations a 51 mm (2) minimum wide air space is required and needs to be
coordinated with the standard dimensions of lintels and shelf angles. The cavity provides water drainage
and prevents moisture migration from the masonry wythe to the steel stud backup wall. The cavity should
be kept clean of mortar droppings. To keep mortar droppings from plugging the weep holes place a
course gravel or drainage material behind the weep holes in the cavity to a minimum depth of 102 mm
(4).
k. Masonry Crack Control. Crack control will be in accordance with the Masonry Manual for
anchored veneer.
l. Weep Holes. Head joint weep holes that extend through the masonry wythe will be provided
immediately above the mortar bed joint containing the horizontal leg of the through wall metal flashing
and near the top of the wall at the same spacing. Details along with the required spacing will be shown
on a wall section on the contract drawings. Weep holes need to be kept free of debris during construction
and need to be functional at the end of the construction period.
m. Head Joint Vents. Head joint vents will be placed near the top of the veneer wythe at the
same spacing as the weep holes. These vents will help maintain a dry cavity.
4. WALL SYSTEM DESIGN REQUIREMENTS. This exterior wall system will be designed assuming that
all out-of-plane lateral loads are resisted entirely by the steel stud backup wall. The veneer anchors will
be designed to transfer those lateral loads to the steel studs. All in-plane loads will be isolated from the
stud wall system. All vertical masonry loads will be carried by a shelf angle or the foundation wall.
Veneer anchorage will provide sufficient movement to account for the story drift displacements around
window and door openings.
a. Steel Studs. Studs will be sized and spaced to resist wind or seismic loads. Wind loads on
steel studs and framing will be in accordance with TI 809-01 and seismic loads will be in accordance with
TI 809-04. Supplemental framing will be added at the heads, jambs and sills of openings, as required by
design, to resist the tributary loads from the opening closures (doors, windows, etc.). The stud system
selected for lateral loading will be checked for deflection, which normally controls panel wall design.
Material thickness for the top and bottom runners will be designed for allowable stress and deflection and
will be equal to or thicker than the steel stud used in the wall. The minimum delivered material thickness
for steel studs is shown in table 1-1.
(1) Section properties. All section properties needed for the design of the steel studs
and framing will be in accordance with AISI.
(2) Allowable stresses. All allowable stresses used for the design of the steel studs and
framing will be in accordance with AISI.
(3) Deflection limits. The allowable steel stud horizontal deflection, due to the
controlling lateral load is defined as follows:
600
L
(Eq 4-1)
Where:
CEMP-E TI 809-07
30 November 1998
4-5
L = The vertical span of the steel studs in mm (in).
(4) Selection of top and bottom runners. The base metal thickness for the steel stud
runners is equal to or greater then for the steel stud. The thickness of the top runner, t will be
sized as follows:
2 / 1
eff y
) b ( F
) e P ( . 7
t
=
(Eq 4-2)
Where:
P = the top end wind load reaction (lbs).
e = the gap between the inner top track and the outer top track as shown in figure 4-1, (in).
F
y
= the yield strength of the top runner metal (psi).
b
eff
= the effective width of the top channel flange for analysis (in).
For double track systems, b
eff
is equal to the stud spacing. With single track systems, b
eff
is equal
to:
+
+ =
)
D e
2 W b
eff
(Eq 4-3)
Where:
W
stud
= the width of the stud flange (in).
D = depth of track overlap in a slip track connection, 32 mm (1.25 in).
b. Veneer Anchors. Anchors will be structurally adequate to transfer the lateral loads to the steel
stud wall in both tension and compression. Capacity will be based on test results of the anchor provided.
The following design procedure to determine the required anchor capacity.
Step 1: Calculate the maximum static out-of-plane distributed load at first cracking.
Figure 4-1: Double Track Slip Joint
CEMP-E TI 809-07
30 November 1998
4-7
V
w
= the veneer unit weight KPa (psf),
A
r
= the area per anchor m
2
(ft
2
),
C3 = constant =2,000,000 metric, (2 English).
S
DS
= the design spectral response acceleration as per Eq C-3
Step 5: Choose the anchor capacity.
if K<= 350 N/mm (2 kips/in) then A
cap
= 1.25 A
des
(Eq 4-11)
if K> 350 mm (2 Kips/in) then A
cap
= 2 A
des
(Eq 4-12)
Where:
K = the anchor stiffness with the load in N/mm (kips/in) of deflection,
A
cap
= the specified load capacity of the anchor to be selected N (lbs).
This design procedure was derived from Western States Clay Products Association test data.
c. Shelf Angles. The angle size and the attachment details of the angle to the building structure
to provide vertical support of the masonry wythe must be determined by the designer. The deflection of
the shelf angle under gravity loading due to the masonry will be limited to not more than 1.6 mm (1/16) at
the end of the horizontal leg. Rotation of the shelf angle support will be included in the 1.6 mm (1/16)
deflection limit for the horizontal leg displacement calculation.
5. WORKMANSHIP. The success of this wall system is dependent upon good detailing and good
workmanship. Careful, quality workmanship is essential to produce a satisfactory masonry veneer steel
stud wall system. Special attention needs to be given to the masonry veneer construction to provide
quality mortar, full head joints, bed joints, clean cavities, proper flashing and weep holes, and to provide
mortar free brick expansion joints. It is essential that the design and detailing requirements in this
document and references contained herein are clearly provided in contract plans and specifications.
6. DESIGN EXAMPLE.
a. Given:
(1) Wall System: An exterior non-loadbearing brick veneer steel stud wall system is
required. The wall section consists of a nominal 102 mm (4 ) face brick wythe, a 60 mm (2-3/8)
cavity, and a backup wall of 152 mm (6) steel studs with a 13 mm (1/2) gypsum sheathing
fastened to each side of the studs. The wall has a vertical span of 3.66 m (12) and is simply
supported.
(2) Design lateral Loading: The design wind pressure for the wall is 1.34KPa (28 psf)
acting inward or outward on the wall.
b. Problem: Check the design of the wall system described above. Check the allowable flexural
stress and the allowable deflection of the steel studs due to that loading.
c. Solution:
(1) Member loading requirements: Since the steel studs are to be designed to resist the
total lateral (wind) loading, the anchors need to be selected to transfer the lateral loading from the
brick wythe to the steel studs.
(2) Assumptions:
CEMP-E TI 809-07
30 November 1998
A-1
APPENDIX A
REFERENCES
GOVERNMENT PUBLICATIONS:
Department of the Army
TI 809-04, Seismic Design of Buildings
TI 809-01, Load Assumptions for Buildings.
TM 5-809-2, Structural Design Criteria for Buildings
TM 5-809-3/NAVFAC DM-2.09/AFM 88-3, Chapter 3. Masonry Structural Design for Buildings.
TM 5-809-10/NAVFAC P-355/AFM 88-3, Chapter 13. Seismic Design for Buildings.
CEGS 04255, Nonbearing Masonry Veneer/Steel Stud Walls
CEGS 05400, Cold-Formed Steel Framing
USACERL Technical Report, http://owww.cecer.army.mil/techreports/wilcfstr.post.pdf
Development of Cold-Formed Steel Seismic Design Guidance
USACERL Design Spreadsheet, http://owww.cecer.army.mil/techreports/wilcfsxl.post.pdf
Development of Cold-Formed Steel Seismic Design Guidance
WES-IM: CAD Libraries:
Standard Cold-Formed Steel Details
Masonry Veneer / Steel Stud Details
Federal Emergency Management Agency
FEMA 273: NEHRP Guidelines for the Seismic Rehabilitation of Buildings
FEMA 274: NEHRP Commentary on the Guidelines for the Seismic Rehabilitation of Buildings
FEMA 302: NEHRP Recommended Provisions for Seismic Regulations for New Buildings and
Other Structures, Part 1 - Provisions
FEMA 303: NEHRP Recommended Provisions for Seismic Regulations for New Buildings and
Other Structures, Part 2 - Commentary
NONGOVERNMENT PUBLICATIONS:
American Institute of Steel Construction (AISC)
1 East Wacker Drive, Suite 3100, Chicago, IL 60601
Steel Construction Manual
American Iron and Steel Institute (AISI)
1101 17th Street, NW
Washington, DC 20036-4700
CEMP-E TI 809-07
30 November 1998
A-2
Specification for the Design of Cold-Formed Steel Structural Members
Cold-Formed Steel Design Manual (Parts: I through VI)
The Design and Fabrication of Cold-Formed Steel Structures
Lightweight Steel Framing Design Manual
Prescriptive Method for Residential Cold-Formed Steel Framing
Commentary on Prescriptive Method for Residential Cold-Formed Steel Framing
Fire-Resistance Ratings of Load-Bearing Steel Stud Walls
Corrosion Protection of Steel Framing Members
RG-9405: Thermal Design Guide for Exterior Walls
RG-9518: Design Guide for Cold-Formed Steel Trusses
RG-9604: Shear Wall Design Guide
AISI Report CF 93-1, Preliminary Design Guide for Cold-Formed C and Z Members
RG-933: Fasteners for Residential Steel Framing
RG-934: Low-Rise Residential Construction Details
Sixth Specialty Conference on Cold-Formed Steel Structures, Effective Lengths for Laterally
Unbraced Compressions Flanges of Continuous Beams Near Intermediate Supports
American Society of Civil Engineers (ASCE)
1801 Alexander Bell Drive
Reston, Virginia 20191-4400
ASCE 7-95: Minimum Design Loads for Buildings and Other Structures
American Society for Testing and Materials (ASTM)
1916 Race Street, Philadelphia, PA 19103
A 370: Standard Test Methods and Definitions for Mechanical testing of Steel Products
A 500: Cold-Formed Welded and Seamless Carbon Steel Structural tubing in Rounds and
Shapes
A 653/A 653M: Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
by the Hot-Dip Process
A 792/792M: Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
A 924/A 924M: General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
C 79: Treated Core and Nontreated Core Gypsum Sheathing Board
C 270: Mortar for Unit Masonry
CEMP-E TI 809-07
30 November 1998
A-3
C 645: Non-Load Bearing (Axial) Steel Studs, Runners (Tracks), and Rigid Furring Channels for
Screw Application of Gypsum Board
C 754: Installation of Steel Framing Members to Receive Screw-Attached Gypsum Board
C 780: Standard Test Method for Preconstruction and Construction Evaluation of Mortars for
Plain and Reinforced Unit Masonry
C 840: Application and Finishing of Gypsum Board
C 841: Installation of Interior Lathing and Furring
C 842: Application of Interior Gypsum Plaster
C 847: Metal Lath
C 926: Application of Portland Cement-Based Plaster
C 954: Steel Drill Screws for the Application of Gypsum Board or Metal Plaster Bases to Steel
Studs From 0.033 in. (0.84mm) to 0.112 in. (2.84 mm) in Thickness
C 955: Load-Bearing (Transverse and Axial) Steel Studs, Runners Tracks), and Bracing or
Bridging for Screw Application of Gypsum Board and Metal Plaster Bases
C 1002: Steel Drill Screws for the Application of Gypsum Board or Metal Plaster Bases
C 1007: Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
C 1072: Standard Test Method for Measurement of Masonry Flexural Bond Strength
American Welding Society (AWS)
2501 N.W. 7
th
Street, Miami, FL 33125
C1.1: Recommended Practice for Resistance Welding
C1.3: Recommended Practice for Resistance Welding, Coated Low Carbon Steels
D1.3: Structural Welding Code - Sheet Steel
Canadian Forestry Service
Ottawa Ontario, Canada
Onysko, , Serviceability Criteria for Residential Floors Based on a Field Study of Consumer
Response, Fortintek canada Corp. Report 03-05-10-008
Onysko, Some Background on Factors Affecting Performance of Floors and Setting of
Performance Criteria, Task Grou Meeting Fortinek Canada Corp.
Center for Cold-Formed Steel Structures (CCFSS)
University of Missouri - Rolla
Department of Civil Engineering
Rolla, Missouri 65401
Cold-Formed Steel Design, Computer Programs
Report on Behavior of Cold-Formed Steel Sections with Web Openings
CEMP-E TI 809-07
30 November 1998
A-4
Technical Library, http://www.umr.edu/~ccfss/
Council of American Building Officials (CABO)
5203 Leesburg Pike, Suite 708, Falls Church, VA 22041
CABO: One and Two Family Dwelling Code
Gypsum Association
810 First Street, NE
Washington, DC 20002
Fire Design Manual
National Association of Architectural Metal Manufacturers (NAAMM)
8 South Michigan Avenue
Chicago, Illinois 60603
NAAMM HMMA 803-97: Steel Tables
NAAMM Standard ML/SFA 540-87: Lightweight Steel Framing Systems Manual, Third Edition,
The National Association of Architectural Metal Manufacturers.
NAAMM Standard ML/SFA 920-91: Guide Specifications for Metal Lathing and Furring, Fourth
Edition, The National Association of Architectural Metal Manufacturers.
Structural Stability Research Council
Lehigh University
Bethlehem, PA 18015
Yura, Fundamentals of Beam Bracing, Is Your Structure Suitably Braced?, April 1993
Virginia Tech University
Blacksburg, Virginia
Kraus, Murray, Floor Vibration Design Criterion for Cold-Formed C-Shaped Supported
Residential Floor systems, Masters Thesis, 10 February 1997.
Western States Clay Products
San Francisco, California
KPFF, Report on Behavior and Design of Anchored Brick Veneer / Metal Stud Systems,
September 1989.
CEMP-E TI 809-07
30 November 1998
B-1
APPENDIX B
COLD-FORMED STEEL TEST PANEL DRAWINGS
This Appendix shows a typical three story barracks framing layout, and the three panels as tested
by CERL. The elevation views are a good representation of the typical shear wall panel layout.
However, the connection details have been modified since the completion of testing. Designers
are to use the new joint details as shown in the design example in appendix D when designing.
CEMP-E TI 809-07
30 November 1998
B-2
Figure B-1: Prototype 3 Story Barracks
CEMP-E TI 809-07
30 November 1998
B-3
Figure B-2: Shear Wall Test Panel A1
CEMP-E TI 809-07
30 November 1998
B-4
Figure B-3: Shear Wall Test Panel A2
CEMP-E TI 809-07
30 November 1998
B-5
Figure B-4: Shear Wall Test Panel D1
CEMP-E TI 809-07
30 November 1998
C-1
APPENDIX C
FEMA 302 AND OTHER STANDARD GUIDANCE FOR COLD-FORMED STEEL SEISMIC DESIGN
C1. INTRODUCTION. Seismic use groups (FEMA 302, 1.3) are used to determine occupancy
importance factors (FEMA 302, Table 1.4). Seismic use group III is for the most critical facilities as
defined in FEMA 302, 1.3. This table is reproduced below:
Table C-1 Occupancy Importance
Factors
Seismic Use Group I
I 1.0
II 1.25
III 1.5
TI 809-04 uses enhanced performance objectives to define seismic design forces for more critical
facilities rather than the occupancy importance factors presented here.
C2. DEFINING GROUND MOTION. Seismic ground motions shall be defined according to FEMA 302
Chapter 4 and TI 809-04 Chapter 3. This paragraph defines ground motions for the maximum
considered earthquake ground motions derived from Maps 1 through 24 (FEMA 302, Chapter 4).
Spectral response acceleration at short periods, S
S
and at 1 second, S
1
are obtained from Maps 1
through 24 of FEMA 302. For most regions of the nation, the maximum considered earthquake ground
motion is defined with a uniform likelihood of exceedance of 2 percent in 50 years (2500 year return
period)
1
.
Site classifications shall be determined based on soil type (A through F), which may be based on shear
wave velocity,
s
average blow counts from standard penetration resistance test N
2
or unconfined shear
strength, s
u
of the soil (FEMA 302, 4.1.2). From the site classifications, values of site coefficients (F
a
and F
v
) are determined for the mapped spectral response acceleration values (FEMA 302, Table 4.1.1.4a
and Table 4.1.1.4b). These tables are reproduced below:
Table C-2a Values of F
a
as a Function of Site Class and Mapped Short-Period
Maximum Considered Earthquake Spectral Acceleration
3
Site Class Short Period Maximum Considered Response Spectral Acceleration
S
S
0.25 S
S
= 0.50 S
S
= 0.75 S
S
= 1.00 S
S
1.25
A 0.8 0.8 0.8 0.8 0.8
B 1.0 1.0 1.0 1.0 1.0
C 1.2 1.2 1.1 1.0 1.0
D 1.6 1.4 1.2 1.1 1.0
E 2.5 1.7 1.2 0.9 a
4
F a a a a a
1
1997 NEHRP, Part 2: Commentary (FEMA 303), Chapter 4 Ground Motion, p. 37.
2
Defined in ASTM D1536-84.
3
Use straight line interpolation for intermediate values of SS.
4
a indicates that a site-specific geotechnical investigation and dynamic site response analyses shall be performed.
CEMP-E TI 809-07
30 November 1998
C-2
Table C-2b Values of F
v
as a Function of Site Class and Mapped 1 Second
Period Maximum Considered Earthquake Spectral Acceleration
5
Site Class 1 Second Period Maximum Considered Response Spectral
Acceleration
S
1
0.1 S
1
= 0.2 S
1
= 0.3 S
1
= 0.4 S
1
0.5
A 0.8 0.8 0.8 0.8 0.8
B 1.0 1.0 1.0 1.0 1.0
C 1.7 1.6 1.5 1.4 1.3
D 2.4 2.0 1.8 1.6 1.5
E 3.5 3.2 2.8 2.4 a
6
F a a a a a
The maximum considered earthquake spectral response acceleration for short periods, S
MS
and at 1
second, S
M1
adjusted for site class effects are calculated as follows (FEMA 302, Eq. 4.1.2.4-1 and
4.1.2.4-2):
S a MS
S F S (Eq C-1)
and
1 v 1 M
S F S (Eq C-2)
These values define the elastic spectra. These values are reduced to define design earthquake spectral
response acceleration at short periods, S
DS
and at 1-second period, S
D1
as follows (FEMA 302, Eq.
4.1.2.5-1 and 4.1.2.5-2):
MS DS
S
3
2
S (Eq C-3)
and
1 M 1 D
S
3
2
S (Eq C-4)
From these terms a design response spectrum is developed as indicated in Figure C-1 (FEMA 302,
Figure 4.1.2.6). For the natural period of the structure, T this spectrum defines values of effective
acceleration. The three regions of this spectrum are defined as follows:
Figure C-1. Design response spectrum.
5
Use straight-line interpolation for intermediate values of S1.
6
a indicates that a site-specific geotechnical investigation and dynamic site response analyses shall be performed.
Period T
T
o
T
s 1.0
SD1
SDS
Sa=SD1/T
S
p
e
c
t
r
a
l
R
e
s
p
o
n
s
e
A
c
c
e
l
e
r
a
t
i
o
n
S
a
CEMP-E TI 809-07
30 November 1998
C-3
For periods less than or equal to, T
0
the design spectral acceleration, S
a
shall be (FEMA 302, Equation
4.1.2.6-1):
DS
0
DS
a
S 4 . 0 T
T
S
6 . 0 S + (Eq C-5)
For periods greater than or equal to T
0
and less than or equal to T
S
, the design spectral response
acceleration , S
a
, shall be taken as equal to S
DS
.
For periods greater than T
S
, the design spectral response acceleration, S
a
, shall be (FEMA 302, Equation
4.1.2.6-3):
T
S
S
1 D
a
(Eq C-6)
Where:
T = the fundamental period of the structure in seconds.
T
0
= 0.2S
D1
/S
DS
.
T
S
= S
D1
/S
DS
.
C3. SEISMIC DESIGN CATEGORY. Each structure shall be assigned a seismic design category based
on their Seismic Use Group and design response coefficients, S
DS
and S
D1
as indicated in the tables
below (from FEMA 302 Tables 4.2.1a and 4.2.1b):
Table C-3a Seismic Design Category Based on Short Period
Response Accelerations
Value of S
DS
Seismic Use Group
I II III
S
DS
< 0.167g A A A
0.167g S
DS
< 0.33g B B C
0.33g S
DS
< 0.50g C C D
0.50g S
DS
D D D
Table C-3b Seismic Design Category Based on 1 Second Period
Response Accelerations
Value of S
DS
Seismic Use Group
I II III
S
D1
< 0.067g A A A
0.067g S
D1
< 0.133g B B C
0.133g S
D1
< 0.20g C C D
0.20g S
D1
D D D
0.75g S
1
E E F
C4. STRUCTURAL CONFIGURATION AND REDUNDANCY. FEMA 302, Section 5.2.3 and 5.2.4
presents guidance on structural configurations and redundancy. Diaphragms are considered flexible if
the maximum lateral deformation of the diaphragm exceeds twice the average story drift of the
associated story (FEMA 302, 5.2.3.1).
A reliability factor, , shall be defined for all structures based on the extent of structural redundancy in
the lateral-force-resisting system. For structures in Seismic Design Categories A, B and C, the value for
CEMP-E TI 809-07
30 November 1998
C-4
shall be taken as 1.0. For structures in categories D, E and F, values for shall be taken as the largest
of the values of
x
calculated for each story of the structure x as follows (FEMA 302, Equation 5.2.4.2):
x max
x
A r
1 C
2
x
(Eq C-7)
Where:
r
maxx
= the ratio of design story shear resisted by the single shear panel carrying the most shear
force in the story to the total shear story, for a given direction of loading. Lateral loads shall
be distributed to panels based on relative stiffness considering the interaction of panels with
varying stiffness.
A
x
= the floor area in m
2
(ft
2
) of the diaphragm level immediately above the story.
need not exceed 1.5, and may be used for any structure. The value of shall not be taken as
less than 1.0.
C1 = constant, 6.1 metric, (20 English)
C5. LOAD COMBINATIONS. Consideration of combinations of loads in the two orthogonal directions is
not needed. The effects of gravity loads and seismic forces shall be combined in accordance with the
factored load combinations as indicated below (ASCE 7
7
).
S 2 . 0 L 5 . 0 E 0 . 1 D 2 . 1 + + + (Eq C-8)
and
E 0 . 1 D 9 . 0 + (Eq C-9)
Where:
D = the dead load.
E = the effect of seismic load.
L = the live load the load factor on L in Equation C-8 shall equal 1.0 for garages, areas
occupied for public assembly, and all areas where the live load is greater than 4.79 kN/m
2
(100 psf).
S = the snow load when the flat roof snow loads exceed 1.44 KN/m
2
(30 psf), the full design
snow load shall be included in Equation C-8.
The effect of seismic loads, E shall be defined as follows, when the effect of gravity and seismic loads
are additive (FEMA 302, 5.2.7):
D S 2 . 0 Q E
DS E
+ (Eq C-10)
Where:
E = the effect of horizontal and vertical earthquake-induced forces.
Q
E
= the maximum horizontal force that could be resisted by the bracing.
= the system redundancy factor.
Q
E
= the effect of horizontal seismic forces.
0.2S
DS
D = the vertical spectral acceleration effect of the seismic load.
S
DS
= the design spectral response acceleration at short periods.
D = the effect of dead load.
The effect of seismic loads, E shall be defined as follows, when the effect of gravity and seismic loads
counteract each other:
7
Minimum Design Loads for Buildings and Other Structures, ASCE 7-95, Section 2.3.2.
CEMP-E TI 809-07
30 November 1998
C-5
D S 2 . 0 Q E
DS E
(Eq C-11)
The effects of gravity load (dead, live and snow load) and seismic forces shall be combined as follows
when the effect of gravity and seismic loads are additive, by combining Equations C-8 and C-10:
E DS
Q S 2 . 0 L 5 . 0 D ) S 2 . 0 2 . 1 ( + + + + (Eq C-12)
The effects of gravity load and seismic forces shall be combined as follows when the effect of gravity
and seismic loads counteract each other, by combining Equations C-9 and C-11:
E DS
Q D ) S 2 . 0 9 . 0 ( + (Eq C-13)
For both expressions in Equations C-12 and C-13, the total horizontal force is Q
E
. This force alone
defines the total lateral load that must be resisted by the shear panel diagonal straps or full panel sheets,
and these elements should be sized based on this force.
The effect of seismic loads, E shall be defined as follows, to account for diagonal strap overstrength
when the effect of gravity and seismic loads are additive:
D S 2 . 0 Q E
DS E 0
+ (Eq C-14)
Where:
0
= the system overstrength.
The effect of seismic loads, E shall be defined as follows, when the effect of gravity and seismic loads
counteract each other:
D S 2 . 0 Q E
DS E 0
(Eq C-15)
The term
0
Q
E
calculated in Equations C-14 and C-15 (TI 809-04, Equations 4-6 and 4-7) need not
exceed the maximum force that can be developed in the diagonal straps, based on the maximum
estimated ultimate strength of these elements. This is expressed as follows:
2 2
s s s max su u E 0
W H
W
t b n F Q Q
+
(Eq C-16)
Where:
F
sumax
= the maximum ultimate stress of the diagonal straps, which equals 1.5 F
su
for ASTM
A653 Grade 33 steel (F
su
= 310 MPa and 45 ksi) and 1.25 F
su
for Grade 50 steel (F
su
= 448
MPa and 65 ksi).
n
s
= the number of diagonal straps.
b
s
= the width of the diagonal straps.
t
s
= the thickness of the diagonal straps.
W = the overall panel width.
H = the overall panel height (see Figure 3-2 for a schematic panel drawing showing W and H).
The effects of gravity load (dead, live and snow load) and seismic forces shall be combined as follows to
account for diagonal strap overstrength, when the effect of gravity and seismic loads are additive, by
combining Equations C-8 and C-14:
E 0 DS
Q S 2 . 0 L 5 . 0 D ) S 2 . 0 2 . 1 ( + + + + (Eq C-17)
CEMP-E TI 809-07
30 November 1998
C-6
The effects of gravity load and seismic forces shall be combined as follows to account for diagonal strap
overstrength, when the effect of gravity and seismic loads counteract each other, by combining
Equations C-9 and C-15:
E 0 DS
Q D ) S 2 . 0 9 . 0 ( + (Eq C-18)
For both expressions in Equations C-17 and C-18, the total horizontal force is
0
Q
E
. Every other term in
these equations represent vertical loads. The shear panel systems should be analyzed based on the
most critical load combination defined by either Equation C-17 or C-18. Each panel component
(including all connections), other than the diagonal strap, should be designed based on these loads.
C6. EQUIVALENT LATERAL FORCE PROCEDURE. FEMA 302 and TI 809-04 present two methods
for defining the structural response: the Equivalent Lateral Force Procedure (FEMA 302, 5.3) and the
Modal Analysis Procedure (FEMA 302, 5.4). Paragraphs C7 through C9 presents the determination of
base shear, period and vertical distribution of lateral forces using the Equivalent Lateral Force
Procedure. Only this method is presented because of its simplicity and recognizing that typical cold-
formed steel structures will likely be low rise construction so that first mode response will dominate the
seismic response of the structures. However if deemed beneficial the modal analysis approach
presented in FEMA 302 and TI 809-04 (Chapter 3-2.c.(2)) could be used.
C7. SEISMIC BASE SHEAR. Using the Equivalent Lateral Force Procedure, the seismic base shear, V
in a given direction shall be determined according to the following equation (FEMA 302, 5.3.2):
W C V
s
(Eq C-19)
Where:
C
s
= the seismic response coefficient.
W = the total dead load and applicable portions of other loads (see FEMA 302, 5.3.2).
The seismic response coefficient, C
s
shall be determined according to the following equation:
I
R
S
C
DS
s
(Eq C-20)
The value for C
s
is
calculated according to Equation C-20; and need not exceed the following:
( )
I
R
T
S
C
1 D
s
(Eq C-21)
but shall not be less than:
I S 1 . 0 C
1 D s
(Eq C-22)
nor shall it be taken as less than the following equation for Seismic Design Categories E and F:
I
R
S 5 . 0
C
1
s
(Eq C-23)
CEMP-E TI 809-07
30 November 1998
C-7
C8. PERIOD DETERMINATION. The fundamental period of the building, T in the direction under
consideration shall be defined using the structural properties and deformational characteristics of the
resisting elements in a properly substantiated analysis (FEMA 302, 5.3.3). Alternatively, T is permitted
to be taken as the approximate fundamental period, T
a
determined in accordance with the following
requirements. The fundamental period, T shall not exceed the product of the coefficient for upper limit
on calculated period, C
u
from Table C-4 and the approximate fundamental period, T
a
determined as
follows:
4 / 3
n T a
h C T (Eq C-24)
Where:
C
T
= constant = 0.0731 metric, (0.030 English) for cold-formed steel shear panels with
diagonal straps.
h
n
= the height in meters (ft - English) above the base to the highest level in the structure.
Table C-4 Coefficient for Upper Limit on Calculated Period
Design Spectral Response
Acceleration at 1 Second, S
D1
Coefficient
C
u
S
D1
< 0.1g 1.7
0.1g S
D1
< 0.15g 1.7
0.15g S
D1
< 0.2g 1.5
0.2g S
D1
< 0.3g 1.4
0.3g S
D1
< 0.4g 1.3
0.4g S
D1
1.2
C9. VERTICAL DISTRIBUTION OF LATERAL SEISMIC FORCES. The vertical distribution of lateral
seismic forces, F
x
(kN or kip), induced at any level shall be determined from the following equations
(FEMA 302, 5.3.4):
V C F
vx x
(Eq C-25)
and
n
1 i
i i
x x
vx
h w
h W
C (Eq C-26)
Where:
C
vx
= the vertical distribution factor.
V = the total design lateral force or shear at the base of the structure (kN or kip).
w
i
and w
x
= the portion of the total gravity load of the structure, W located or assigned to level i
or x.
h
i
and h
x
= the height (m or ft) from the base to level i or x.
The horizontal distribution of seismic story shear in any story, V
x
(kN or kips) shall be determined from
the following equation (FEMA 302, 5.3.5):
n
x i
i x
F V (Eq C-27)
Where:
F
i
= the portion of the seismic base shear, V (kN or kips) induced at level i.
CEMP-E TI 809-07
30 November 1998
C-8
The seismic design story shear, V
x
(kN or kips) shall be distributed to the various vertical elements of the
seismic-force-resisting system in the story under consideration based on the relative lateral stiffness of
the vertical resisting elements and the diaphragm.
C10. STRUCTURAL OVERTURNING RESISTANCE. The structure shall be designed to resist
overturning effects caused by the seismic forces determined from Equation C-25. At any story, the
increment of overturning moment in the story under consideration shall be distributed to the various
vertical force resisting elements in the same proportion as the distribution of the horizontal shears to
those elements (FEMA 302, 5.3.6).
The overturning moments at Level x, M
x
(kN-m or kip-ft), shall be determined from the following
equation:
n
x i
x i i
) h h ( F Mx (Eq C-28)
Where:
F
i
= the portion of the seismic base shear, V, induced at Level i.
h
i
and h
x
= the height (m or ft) from the base to Level i or x.
Foundations shall be designed for the foundation overturning design moment, M
f
(kN-m or kip-ft) at the
foundation-soil interface determined using Equation C-28 at the foundation level, multiplied by a
reduction factor of 0.75.
C11. STORY DRIFTS AND P-DELTA EFFECTS. The story drifts and, member forces and moments
due to P-delta effects shall be determined in accordance with the following guidance (FEMA 302, 5.37).
Story drifts shall be calculated based on the application of design seismic forces to a mathematical
model of the structure. The model shall include the stiffness and strength of all elements that are
significant to the distribution of forces and deformations in the structure and shall represent the spatial
distribution of the mass and stiffness of the structure. The design story drift, shall be computed as the
difference of the deflections at the center of mass at the top and bottom of the story under consideration.
The deflections of level x,
x
(mm or in) shall be determined according to the following equation:
I
C
xe d
x
(Eq C-29)
Where:
xe
= the deflections determined by an elastic analysis (mm or in.) based on the forces defined in
Equation C-25.
For determining compliance with the story drift limitations in Table 3-2, the deflections of Level x,
x
(mm
or in) shall be calculated as expressed in Equation C-29. For the purposes of this drift analysis only, the
computed fundamental period, T in seconds, of the structure may be used without the upper bound
limitations specified in Table C-4, when determining drift level seismic design forces.
The design story drift, (mm or in) shall be increased by the incremental factor relating to the P-delta
effects if required by the following guidance (FEMA 302, 5.3.7.2). The P-delta effects on story shears
and moments, the resulting member forces and moments, and the story drifts induced by these effects
are not required to be considered when the stability coefficient, as determined by the following equation
is equal to or less than 0.10:
CEMP-E TI 809-07
30 November 1998
C-9
d sx x
x
C h V
P
(Eq C-30)
Where:
P
x
= the total vertical design load at and above Level x (kN or kip). When calculating the vertical
design load for purposes of determining P-delta, the individual load factors need not exceed
1.0.
= the design story drift occurring simultaneously with V
x
(mm or in).
V
x
= the seismic shear force acting between Level x and x-1 (kN or kip).
The stability coefficient, shall not exceed
max
determined as follows:
25 . 0
C
5 . 0
d
max
(Eq C-31)
Where:
= the ratio of shear demand to shear capacity for the story between Level x and x - 1. This
ratio may conservatively be taken as 1.0.
When the stability coefficient, is greater than 0.10 but less than or equal to
max
the incremental factor
related to P-delta effects, a
d
shall be determined by rational analysis (see FEMA 303, Commentary,
5.3.7). To obtain the story drift for including the P-delta effects, the design story drift, shall be
multiplied by 1.0/(1 - ). When is greater than
max
the structure is potentially unstable and shall be
redesigned.
C12. DIAGONAL STRAP DESIGN. From the values of seismic story shear, V
x
and additional shear
force due to torsion, the shear panel dimensions are defined and diagonal straps designed. The straps
are tension only members and their design strength is defined by the following equation (AISI, C2, p. V
45):
sy s s t sy n t
F ) t b ( F A (Eq C-32)
Where:
t
= the resistance factor for tensile members (0.95).
A
n
= the cross-sectional area of the all diagonal straps in tension (b
s
t
s
).
b
s
= the width of an individual diagonal strap.
t
s
= the thickness of an individual strap.
F
sy
= the design yield strength of the strap.
The shear panel lateral yield capacity, Q
sy
when the diagonal straps are the sole lateral-load-resisting
element is calculated as follows:
,
_
2 2
sy s s s sy
W H
W
F t b n Q (Eq C-33)
Where:
W = the width of a trial shear panel.
H = the height of a trial shear panel.
CEMP-E TI 809-07
30 November 1998
C-10
The shear panel design strength,
t
Q
sy
must be greater than the seismic story shear, V
x
and additional
shear force due to torsion, Qsi for all shear panels resisting in the frame of the building for which these
forces are applied. This is expressed as:
si x
2 2
sy s s s t sy t
Q V
W H
W
F t b n Q +
1
1
]
1
,
_
+
(Eq C-34)
The number of shear panels, panel width, height, and strap size and strength shall be designed
according to Equation C-34 to meet minimum lateral yield capacity. All diagonal strap material must be
ASTM A653 steel. Diagonal straps may not use re-rolled steel, because the re-rolling strain hardens the
material, increasing material strength variability and reducing elongation (see USACERL TR FL-XX,
Chapter 4 for a discussion of this concern).
C13. COLUMN AXIAL CAPACITY. The column axial design strength, P shall be determined as follows
for columns built-up with cold-formed steel studs or individual structural tubing members (AISI, C4,
Concentrically Loaded Compression Members):
n e c
F A P (Eq C-35)
Where:
c
= the resistance factor for compression, which equals 0.85.
A
e
= the effective area at the stress F
n
.
F
n
= the nominal strength of the column, determined as follows:
For
c
1.5
cy n
F ) 658 . 0 ( F
2
c
(Eq C-36)
For
c
> 1.5
cy
2
c
n
F
877 . 0
F
1
]
1
(Eq C-37)
Where:
e
cy
c
F
F
(Eq C-38)
Where:
F
cy
= the column design yield strength.
( )
2
2
e
r
KL
E
F
(Eq C-39)
Where:
E = the modulus of elasticity.
K = the effective length factor.
L = the unbraced length of the column.
r = the radius of gyration of the full, unreduced column cross section, calculated as follows:
CEMP-E TI 809-07
30 November 1998
C-11
A
I
r (Eq C-40)
The effective area, A
e
is calculated as follows for columns built-up from cold-formed steel studs such that
they form a closed section or structural tube columns (AISI, C4):
) b w ( nt A A
c c e
(Eq C-41)
Where:
A
c
= the nominal column area.
n = the number of studs making up the column, or is 2 when using structural tube columns.
t
c
= the thickness of the stud material used in the built-up columns, or the thickness of the
structural tube column.
w = the flat width of the stud web making up the built-up columns, or the width of the structural
tube face perpendicular to the plane of the panel. Assuming the outside radius of the stud
corners is twice the thickness, t
c
this may be calculated as follows:
c s
t 4 d w (Eq C-42)
d
s
= the depth of the studs making up the built-up columns, or the structural tube width
perpendicular to the plane of the panel,
b = the effective width and shall be determined as follows (AISI, B2.2):
for 70
t
w
and , 0
w
d
5 . 0
c
h
and
the distance between centers of holes 0.5w and 3d
h
,
b = w d
h
when 0.673 (Eq C-43)
1
]
1
w
d 8 . 0 22 . 0
1 w
b
h
when > 0.673 (Eq C-44)
Where:
d
h
= the diameter of holes.
= a slenderness factor defined as follows (AISI, B2.1):
E
F
t
w
k
052 . 1
n
c
,
_
(Eq C-45)
Where:
k = the plate buckling coefficient, equal to 4 for the studs making up the built-up columns or
structural tube columns.
C14. COLUMN SHEAR CAPACITY. The column shear design strength, V
c
shall be determined as
follows for columns built-up with cold-formed steel studs or individual structural tubing members (AISI,
C3.2, Strength for Shear Only):
CEMP-E TI 809-07
30 November 1998
C-12
For
cy
v
c
F
Ek
96 . 0
t
h
c s c cy v C
t n h F 60 . 0 V (Eq C-46)
Where:
h = the depth of the flat portion of the web, which equals the stud flange width for the built-up
columns.
k
v
= the shear buckling coefficient, which equals 5.34 for both built-up and structural tubing
columns.
v
= 1.0
h
c
= the depth of the column, which is the column width in the in-plane direction of the panel.
n
s
= the number of faces of a shear panel with diagonal straps (i.e., 1 or 2).
C15. CONNECTION SHEAR AND PULL-OVER. The design shear (AISI E4.3.1) and pull-over per
screw (AISI E4.4.2), P
s
shall be calculated as follows:
) andP P min( P
nov ns s s
(Eq C-47)
Where, the nominal shear strength per screw, P
ns
, shall be determined as follows:
For t
2
/t
1
1.0, P
ns
shall be taken as the smallest of:
2 u
3
2 ns
F d t 2 . 4 P tilting mode of failure (Eq C-48)
1 u 1 ns
dF t 7 . 2 P bearing mode of failure (Eq C-49)
2 u 2 ns
dF t 7 . 2 P bearing mode of failure (Eq C-50)
For t
2
/t
1
2.5, P
ns
shall be taken as the smaller of:
1 u 1 ns
dF t 7 . 2 P bearing mode of failure (Eq C-51)
2 u 2 ns
dF t 7 . 2 P bearing mode of failure (Eq C-52)
For 1.0 < t
2
/t
1
< 2.5, P
ns
shall be determined by linear interpolation between the two cases above.
Where:
s
= the screw resistance factor for shear, equal to 0.5.
d = the nominal screw diameter.
t
1
= the thickness of the member in contact with the screw head.
t
2
= the thickness of the member not in contact with the screw head.
F
u1
= the ultimate tensile strength of the member in contact with the screw head.
F
u2
= the ultimate tensile strength of the member not in contact with the screw head.
The nominal shear strength per screw, P
ns
may also be determined by AISI Tables IV-7a and IV-7b for
connections to various sheet thicknesses for sheets with ultimate strengths of 310 MPa (45 ksi) and 448
MPa (65 ksi) (ASTM A653, Grade 33 and 50 respectively). These tables may only be used if ultimate
strengths of the materials being connected are the same.
CEMP-E TI 809-07
30 November 1998
C-13
The nominal pull-over strength, P
nov
shall be calculated as follows:
1 u w 1 nov
F d t 5 . 1 P (Eq C-53)
Where:
d
w
= the larger of the screw head diameter or the washer diameter, and shall not be taken as
larger than 13 mm ( inch).
C16. WELDED CONNECTION DESIGN. Diagonal strap-to-column connection fillet weld design based
on AISI (E2.4 Fillet Welds) is summarized below. The design shear strength for loading in the
longitudinal direction, P
L
shall be determined as follows:
For L/t < 25
u L
tLF
t
L 01 . 0
1 P
,
_
(Eq C-54)
Where:
= 0.60.
L = the length of fillet weld.
t = the least value of the thicknesses of the two members being welded.
For L/t 25
u L
tLF 75 . 0 P (Eq C-55)
Where:
= 0.55
The design shear strength of loading in the transverse direction, P
T
shall be determined as follows:
u T
tLF P (Eq C-56)
Where:
= 0.60.
For fillet welds to heavy strap material, thicker than 0.150 inches, the design shear strength for both
longitudinal and transverse loading due to weld failure, P
W
8
shall not exceed the following:
xx w W
LF t 75 . 0 P (Eq C-57)
Where:
= 0.60.
t
w
= the effective throat, equal to 0.707 times the least leg of the weld in-plane or out-of-plane of
the materials being welded. A larger effective throat shall be permitted if measurement
shows that the welding procedure to be used consistently yields a larger value of t
w
.
F
xx
= the weld metal strength designation in AWS electrode classification.
C17. ANCHOR FLARE BEVEL GROVE WELD DESIGN. Column-to-anchor flare bevel grove weld
design based on AISI (E2.5 Flare Grove Welds) is summarized below. The design strength of the
longitudinal loaded flare bevel grove weld, P
G
shall be determined as follows:
8
AISI Commentary, E2.4, indicates that this equation is needed to cover the possibility of weld failure through the throat of the weld
material, because tests that ensured tearing in the plate were not conducted on plates thicker than 0.15 inches.
CEMP-E TI 809-07
30 November 1998
C-14
For t
c
t
w
< 2t
c
(single shear)
cu c G G
LF t 75 . 0 P (Eq C-58)
For t
w
2t
c
(double shear)
cu c G G
LF t 5 . 1 P (Eq C-59)
Where:
G
= the resistance factor for flare grove welds, equal to 0.55.
t
c
= the thickness of the column material.
L = the length of the flare bevel grove weld.
F
cu
= the ultimate strength of the column steel.
C18. ANCHOR BOLT CONE FAILURE. Embedded anchors shall be used for all anchor bolts described
here. The anchor bolt cone failure design strength, P
c
shall exceed the applied tensile force per bolt,
P
tAB
(Equation 3-37). Either one or two anchor bolts may be installed on both sides of the columns (i.e.,
n
AB
equal to 2 or 4). If only one bolt is installed, the cone failure surface will be that of a simple cone. If
two bolts are installed, the critical failure surface will be the minimum failure surface defined by two
independent cones or a surface that accounts for the overlap of two cones. If the two bolts on the same
side of the column are close enough relative to the bolt embedment length, then the combined surface
will control. The column anchor bolts at the outside of the shear panel will always be more highly
stressed than those at the inside. These bolts will be more critically loaded by uplift forces due to the
direction of diagonal strap forces and moment in the column. A cone failure surface including bolts on
both sides of the columns will never be more critical than the cone for bolts only at the outside of the
shear panel. Therefore, only the cone with bolts on the outside are considered. The anchor bolt cone
failure design strength, P
c
(in pounds) is determined by
9
:
c c c c
A ' f 4 P (Eq C-60)
Where:
c
= the cone strength reduction factor - a value of 0.85 for uncracked concrete.
f
c
= the specified concrete compressive strength in psi
A
c
= the minimum of the area of a single anchor bolt stress cone (A
c1
) or the summation of the
combined failure surface for two overlapping stress cones divided by two (A
c2
), in inches
2
.
The area of individual stress cones is dependent on the angle of cone failure. In the case of
expansion anchors this angle varies from about 60 degrees (measure from the axis of the
anchor) for short embedments (l
AB
2 inches) to 45 degrees for l
AB
6 inches. In this
guidance this angle will conservatively be set equal to 45 degrees. Then the radius of the
cone at the concrete surface, r
c
is equal to anchor embedment length, l
AB
. The area of an
individual stress cone failure surface, A
c1
shall be calculated as follows:
2
AB
2
AB
2
c c 1 c
l 2 l r r A + (Eq C-61)
The area of the combined failure surface for two overlapping stress cones, divided by two for an
individual anchor bolt, A
c2
shall be calculated as follows:
( )
cc AB AB
2
AB
2
c
cc c
2 c
d 2 l l
2
2
l r
2
d 2 r
A + +
+
(Eq C-62)
9
ACI 355.1R-91, Equation 3.2.
CEMP-E TI 809-07
30 November 1998
C-15
The anchor bolts shall not be installed too close to the edge of a concrete beam or slab, or edge failure
could occur before developing the cone strength. The minimum distance from the center of an anchor
bolt to the edge of the concrete to prevent side cone failure, m (in inches) is determined as follows:
10
c
t
AB
' f 73
F
d m (Eq C-63)
10
ACI 355.1R-91, Equation 3.3.
CEMP-E TI 809-07
30 November 1998
D-1
APPENDIX D
SEISMIC DESIGN EXAMPLE
(English I-P units only)
D1. EXAMPLE DESIGN PROBLEM. An example problem is presented here to demonstrate the
design process presented in Chapter 3 and Appendix C. Shear panels will be designed in the short
direction of the building only to illustrate the design process. In an actual building the lateral load
resisting system must be designed in both directions. This example is a barracks-type building that
will be designed for construction at Fort Lewis, located between Tacoma and Olympia, Washington.
This building is similar to a Prototype 3 Story Steel Stud Framed Barracks Building for Seismic Zones
0 2
1
. The reader will be referred to tabular data and equations presented in Chapter 3 and
Appendix C. When needed, FEMA 302 guidance will be referenced.
The barracks building has a Seismic Use Group of I (FEMA 302, 1.3), which gives it an Occupancy
Importance Factor, I, of 1.0 (see Table C-1).
D2. GROUND MOTION DEFINITION. The maximum considered earthquake ground motions are
determined from spectral response acceleration Maps 9 and 10 (for the Pacific Northwest). The
spectral response acceleration for short periods, S
S
, is 1.2 g (Map 9). The spectral response
acceleration for 1 second, S
1
, is 0.39 g (Map 10). Table D-1 summarizes these values. These
values are determined by interpolating between the map contours for the Fort Lewis location. The
soil conditions are unknown, so a reasonable worst-case site classification of D is used. Values of
Site Coefficients, F
a
and F
v
, are calculated based on straight-line interpolation from the values in
Tables C-2a and C-2b, and are shown in Table D-1. Values for the maximum considered earthquake
spectral response acceleration for short periods, S
MS
and at 1 second, S
M1
adjusted for site class
effects, are calculated using Equations C-1 and C-2, and are shown in Table D-1. Design earthquake
spectral response acceleration at short periods, S
DS
and 1 second period, S
D1
are calculated using
Equations C-3 and C-4, and are shown in Table D-1.
Table D-1. Earthquake Ground Motion Definition
Summary for Fort Lewis.
Importance Factor, I 1.0
Short Period Spectral Response Acceleration, S
S
1.2 g
1 Second Spectral Response Acceleration, S
1
0.39 g
Site Classification D
Site Coefficient, F
a
1.02
Site Coefficient, F
v
1.62
Adjusted Short Period Spectral Response Acceleration, S
MS
1.22 g
Adjusted 1 Second Spectral Response Acceleration, S
M1
0.63 g
Design Short Period Spectral Response Acceleration, S
DS
0.82 g
Design Short Period Spectral Response Acceleration, S
D1
0.42 g
T
0
0.103 seconds
T
S
0.516 seconds
Assumed Design Spectral Response Acceleration, S
a
0.82 g
Seismic Design Category D
Response Modification Factor, R 4
Deflection Amplification Factor, C
d
3.5
A design response spectrum is developed from these terms, as described in Appendix C, Paragraph
C2, using Equations C-5 and C-6, and plotted in Figure D-1. For the natural period of the structure,
T, this spectrum defines values of effective acceleration. The natural period of the barracks building,
T, will almost certainly fall between T
0
and T
S
, defined in Appendix C, Paragraph C2, so that the
1
U.S. Army Corps of Engineers Barracks Prototype Department of the Army, for the National Association of Architectural Metal
Manufactures (NAAMM), by Matsen Ford Design, Drawings Dated 1/3/97.
CEMP-E TI 809-07
30 November 1998
D-2
design spectral acceleration S
a
will equal S
DS
. Values for T
0
and T
S
are shown in Table D-1. After
the building frame is designed, the building natural period will be calculated to ensure that it falls
between T
0
and T
S
, and corrections will be made if needed.
D3. SEISMIC DESIGN CATEGORY. The seismic design category for the barracks building is
determined from Tables C-3a or C-3b, based on the seismic use groups and values of S
DS
and S
D1
. If
the tables give different categories, the larger letter is chosen. For the barracks building, the seismic
design category is D (see Table D-1).
D4. STRUCTURAL DESIGN CRITERIA. The lateral-load-resisting system of the barracks building
will be designed with cold-formed steel shear panels with diagonal straps acting as the sole lateral-
load-resisting element. Values of the response modification factor, R and deflection amplification
factor, C
d
are taken from Table 3-1 and shown again in Table D-1.
The diaphragms of the barracks buildings are reinforced concrete and are considered rigid. The
reliability factor,
x
, is calculated using Equation C-7, which for the barracks building for every floor
level gives:
8 . 1
. ft . sq 8971
18
1
20
2
A r
20
2
x x max
x
= = = (Eq D-1)
The value of
x
shall not be taken as less than 1.0. Therefore no correction is needed for lateral-load-
resisting system reliability.
D5. BARRACKS BUILDING LOAD CALCULATIONS. The effects of gravity load (dead, live, and
snow) and seismic forces shall be combined as defined by Equations C-12 and C-13. As explained in
Appendix C, Paragraph C5, the total lateral force that must be resisted by the shear panel diagonal
straps is simply defined by Q
E
in these equations. In the case of the barracks building this becomes
Q
E
, and the diagonal straps are first sized based on this force.
The barracks building will be designed to act independently in the two orthogonal directions. Figures
D-2 and D-3 show schematic drawings of the barracks building. Figure D-2 shows the plan view and
long-direction elevation. Figure D-3 shows the short-direction elevation of the building. Table D-2
summarizes the weight calculations for the entire building using spreadsheet calculations. These
weights include roof and floor dead load (20 and 40 psf, respectively); exterior wall weight (10 psf);
interior wall weight (10 psf); brick veneer weight (40 psf); and room and corridor live load (40 and 80
psf, respectively).
2
The brick veneer is self-supporting for gravity loads, and vertical and in-plane
lateral seismic forces. The building lateral-load-resisting system (shear panels) does resist out-of-
plane lateral seismic forces from the brick veneer weight. Therefore, the out-of-plane long-direction
brick veneer lateral seismic forces are resisted by the short-direction shear panels.
The short-direction shear panels will be placed at every bay (20 feet, 6-5/8 inches spacing) of the
building as shown in Figure D-2, for a total of nine short-direction frames. A trial shear panel
configuration will be assumed in which two shear panels are placed at every frame, as shown in
Figure D-3. Figure D-3 shows that two shear panels will be placed against the perpendicular outside
walls of the building. Shear panels will be located in the same bay at each floor level, with decreasing
capacity at the higher floor levels.
2
Barracks Prototype Drawings, Sheet C-1.
CEMP-E TI 809-07
30 November 1998
D-3
Table D-2. Barracks Building Weight Calculations.
The ground snow load, p
g
, for Fort Lewis is 20 psf
3
. The flat-roof snow load, p
f
, is calculated as
follows (ASCE 7-95, Eq 7-1)
4
:
psf 6 . 12 ) psf 20 )( 0 . 1 )( 0 . 1 )( 9 . 0 ( 7 . 0 Ip C C 7 . 0 p
g t e f
= = = (Eq D-2)
Where:
C
e
= the exposure factor (ASCE 7-95, Table 7-2), which for an exposure category C, fully
exposed roof is 0.9.
C
t
= the thermal factor (ASCE 7-95, Table 7-3), which is taken as 1.0.
I = the importance factor (ASCE 7-95, Table 7-4), which for Category II of the barracks
building is 1.0.
However, the flat-roof snow load shall not be less than the ground snow load multiplied by the
importance factor (p
g
I), so that the p
f
= 20 psf. The sloped-roof snow load, p
s
is calculated as follows
(ASCE 7-95, Eq 7-2):
psf 15 ) psf 20 )( 75 . 0 ( p C p
f s s
= = = (Eq D-3)
Where:
C
s
= the roof slope factor (ASCE 7-95, Figure 7.2), which is 0.75 for the barracks building with
a 5/12 roof slope.
The snow load will not be used in this example because the flat roof snow load does not exceed 30
psf, and therefore is not included in load combinations that include seismic forces.
D6. EARTHQUAKE FORCE DEFINITION. Seismic forces are now defined based on the equivalent
lateral force procedure (see Appendix C, Paragraphs C6 through C9). The seismic base shear, V in
the direction of the shear walls is given by (Equation C-19):
W C V
s
= (Eq D-4)
The seismic response coefficient, C
s
(Equation C-20) is calculated with the variables given in Table
D-1, which becomes:
g
g
I
R
S
C
DS
s
204 . 0
0 . 1
4
82 . 0
= = = (Eq D-5)
The value of for C
s
need not exceed the following (Equation C-21), where T = T
a
(see Equation D-8):
3
ASCE 7-95, Chapter 7 and Chapter 7 Commentary.
4
NEHRP, Section 5.3.2, states that in areas where the design flat roof snow load does not exceed 30 psf, the effective snow
load is permitted to be taken as zero. The Commentary to the 1997 NEHRP (FEMA 303) Section 5.32, states that snow loads
up to 30 psf are not considered, in the weight, W, used to calculate the lateral earthquake loads.
Self Long Short
Total Total Supporting Direction Direction Total
Floor Floor Total Total Dead for gravity Brick Brick Room Corridor Floor
Panel Dead Floor Floor Floor Dead Story Exterior Exterior Interior Interior Load Brick Veneer Veneer Live Room Live Corridor Live
Level Load Length Width Area Load, D Height Walls Walls, EW Walls Walls, IW D
T
=D+EW+IW Veneer B
L
B
S
Load Area Load Area Load, L
(psf) (ft) (ft) (ft
2
) (kips) (ft) (psf) (kips) (psf) (kips) (kips) (psf) (kips) (kips) (psf) (ft
2
) (psf) (ft
2
) (kips)
Roof
3rd 20 164.42 54.67 8988 179.762 4.2 10 18.5 10 30.09 228.4 40 55.6 18.5 0 7892 0 1096 0
2nd 45 164.42 54.67 8988 404.465 9.0 10 39.3 10 63.74 507.5 40 117.8 39.2 40 7892 80 1096 403
1st 45 164.42 54.67 8988 404.465 9.3 10 40.7 10 66.11 511.3 40 122.2 40.6 40 7892 80 1096 403
CEMP-E TI 809-07
30 November 1998
D-4
( )
g 292 . 0
)
0 . 1
4
( 36 . 0
g 42 . 0
I
R
T
S
C
1 D
s
= = = (Eq D-6)
but shall not be less than (Equation C-22):
g g I S C
D s
042 . 0 ) 0 . 1 )( 42 . 0 ( 1 . 0 1 . 0
1
= = = (Eq D-7)
The approximate fundamental period, T
a
, in seconds is calculated using the following equation
(Equation C-24):
onds sec 36 . 0 ) 27 )( 030 . 0 ( h C T
4
3
4
3
n T a
= = = (Eq D-8)
Where:
C
T
= 0.030 for cold-formed steel shear panels with diagonal straps.
h
n
= the height, which is 27 feet to the top of the shear walls for the barracks building.
This approximate period, T
a
is used for the fundamental period, T in Equation D-6 without correction.
D7. SHORT-DIRECTION EARTHQUAKE FORCE DEFINITION. The total dead load and applicable
portions of other loads, W are calculated from the loads presented in Table D-2 as follows:
L 25 . 0 B IW EW D L 25 . 0 B D W
T
+ + + + = + + = (Eq D-9)
For the short direction of the building this weight, W
S
becomes:
L 25 . 0 B IW EW D L 25 . 0 B D W
L L T S
+ + + + = + + = (Eq D-10)
Where:
D
T
= the total dead load.
B = the brick veneer weight.
L = the live load.
D = the floor and roof dead load.
EW = the exterior wall weight.
IW = the interior wall weight.
B
L
= the brick veneer weight in the long direction of the building carried by the shear panels in
the short direction of the building.
The cumulative total weight in the short direction of the building, W
S
at the first floor is equal to 1744
kips, as shown in Table D-3.
The base shear in the short direction of the building, V
S
, is now calculated from Equation C-19:
kips 356 ) kips 1744 )( g 204 . 0 ( W C V
S s S
= = = (Eq D-11)
CEMP-E TI 809-07
30 November 1998
D-5
Table D-3. Short-Direction Lateral Seismic Force Calculations for the Barracks Building.
The vertical distribution of lateral seismic forces in the short direction, F
xS
, induced at any level shall
be determined using Equation C-25. These values are determined based on the vertical distribution
factor in the short direction, C
vxS
, calculated in Equation C-26. Values for W
xS
, h
x
, w
i
, and h
i
used in
Equation C-26 are given in Table D-3. The short-direction lateral seismic forces, F
xS
, shown in Table
D-3 are the lateral force per frame in the short direction. There are nine frames in the short direction,
n
S
5
, so that lateral force per frame is calculated as follows:
S
S vxS
xS
n
V C
F = (Eq D-12)
The barracks building is very regular in plan, so the center of rigidity, C
R
in both directions should be
at the center of the building. The accidental torsion is accounted for by offsetting the center of mass,
C
M
, 5 percent in both directions in plan at each floor level (see Figure D-2). The total mass at each
floor level in each direction (long and short) is multiplied by the 5 percent of the building dimension in
that direction to calculate the accidental torsional moment, M
ta
at each floor level. Similar to the
lateral seismic forces, the accidental torsional moments, M
tax
are distributed along the floors of the
building according to the vertical distribution factor given in Equation C-26, which is expressed as
follows:
)] FloorWidth ( C V ) h FloorLengt ( C V [ 5 . 0 M
vxL L vxS S tax
+ = (Eq D-13)
Where:
C
vxL
= vertical distribution factor in the long direction.
V
L
= the base shear in the long direction.
Table D-3 gives values for accidental torsional moments, M
tax
at each floor level.
The torsional resistance, M
tr
(see Equation 3-3) is proportional to the square of the distance from the
center of resistance to the plane of each panel. The torsional resistance is also proportional to the
lateral stiffness of each panel. Therefore, because the barracks building is very long in one direction,
the shear panels in the short direction near the ends of the building will dominate the torsional
resistance. For this example it will be assumed that all torsional resistance comes from the shear
panels in the short direction. The torsional resistance from all shear panels, M
tr
, in the short direction
can be expressed as follows (from Equation 3-3):
5
The symbol for the number of frames in the short direction, nS, must not be confused with the number of faces with diagonal
straps on a given shear panel, ns.
Short Short Short Dir Number Short Dir Max. Add Short Dir
Direction Seismic Dir Height Vertical Frames Lateral Shear Seismic
Total Response Base at Floor Distribution in Short Seismic Accidental due to Acc Story
Panel Weight Coefficient Shear Level Factor Dir Force/frame Torsion Torsion Shear
Level W
S
C
s
V
S
h
xS
or h
xL
C
vxS
n
S
F
xS
M
tax
Q
sic
V
xS
(k-mass) (g) (kips) (ft) (kips) (kip-ft) (kips) (kips)
Roof
3rd 284 27.042 0.276 9 10.895 1040 2.529 13.424
Cumulative 284
2nd 726 18.583 0.484 9 19.142 1837 4.469 37.035
Cumulative 1010
1st 734 9.125 0.240 9 9.506 912 2.218 48.758
Cumulative 1744 0.204 356
CEMP-E TI 809-07
30 November 1998
D-6
[ ]
si
si
n
i
si i tr
k
k x x x k M
) 30 ( ) ' 5 . 20 ( 4
) ' 5 . 20 4 ( ) ' 5 . 20 3 ( ) ' 5 . 20 2 ( ) ' 5 . 20 ( 4
2
2 2 2 2
1
2
=
+ + + = =
=
(Eq D-14)
The shear panel furthest from the center of rigidity provides the greatest torsional resistance.
However, the end panels in the short direction against the exterior walls will not be loaded as heavily
as the panels one bay in from the end because the end panels have only half the tributary area as the
panel one bay in. Therefore, the panels one bay in from the end will be the most critically loaded
because of lateral loads in the short axis and the full width of that bay, and because of its large
contribution to torsional resistance. The torsional resistance of the two shear panels that make up the
critical short-direction frame, M
trc
, may be expressed as follows:
[ ] = = =
=
si
2
si
2
n
1 i
si
2
i trc
k ) 9 ( ) ' 5 . 20 ( 2 k ) 5 . 20 x 3 ( 2 k M (Eq D-15)
Equation D-15 shows that the critical short-direction frame provides 3/20 of the total building torsional
resistance (Equation D-15 divided by Equation D-14). This ratio can be used to calculate the applied
torsion in the critical frame by equating the total accidental torsion, M
ta
, and torsional resistance from
all shear panels, M
tr
, as follows:
ta ta
tr
trc
trc
M
20
3
M
M
M
M = = (Eq D-16)
The additional shear force due to accidental torsion for the critical frame is now calculated by solving
Equation 3-3 for Q
sic
,as follows:
c
trc
sic
M
Q
= (Eq D-17)
Values of this additional shear force are given in Table D-3 for each floor level.
Values of seismic story shear in the short direction, V
xS
, are calculated by modifying Equation C-27 to
include the effects of accidental torsion as follows:
( )
=
+ =
n
x i
sic i xS
Q F V (Eq D-18)
D8. LONG-DIRECTION EARTHQUAKE FORCE DEFINITION. The same process is repeated for
the definition of earthquake forces in the long direction of the building. These results are summarized
in Table D-4. The effects from accidental torsion are not added to the frames in the long direction of
the building.
CEMP-E TI 809-07
30 November 1998
D-7
Table D-4. Long Direction Lateral Seismic Force Calculations for the Barracks Building.
D9. DIAGONAL STRAP DESIGN. From the values of seismic story shear, V
x
(V
x
+ Q
si
in Equation 3-
4) the shear panel diagonal straps are sized according to Equation 3-4. Values of the shear panel
design strength,
t
Q
sy
are given in Table D-5. Two identical shear panels are used at each floor level,
and applied story shear in the short direction, V
xS
per shear panel are shown in Table D-5. Trial
shear panel dimensions and diagonal strap sizes for each floor level are defined so that the design
strength,
t
Q
sy
exceeds the applied story shear, V
xS
per shear panel, using the spreadsheet program
that models Equation 3-4. Table D-5 shows trial shear panel configurations that meet this
requirement for each floor of the critical frame in the barracks building example. All diagonal straps
require ASTM 653, Grade 33 or Grade 50 steel. Panel dimensions are based on the dimensions
given for Shearwall Type SW-3 (Interior Load-Bearing Walls) of the barracks building drawings
(Sheet S-6).
The diagonal straps are the sole lateral-load-resisting element, and as such they determine the story
drifts. The elastic deflections,
xe
, at each floor level are calculated as follows:
S
xS
sy
sy
xe
n
V
Q
= (Eq D-19)
where
sy
is the lateral deflection at
diagonal strap yielding given by:
+
=
W
W H
E
F
2 2
sy
sy
(Eq D-20)
Values of
xe
are given in Table D-5, for the trial diagonal straps at each floor level in the short
direction of the building. The design story drifts, are the differences in deflection at the center of
mass at the top and bottom of the story under consideration. These deflections are calculated from
the elastic deflection,
xe
as follows (from Equation C-29):
I
C
xe d
x
= = (Eq D-21)
Where :
C
d
= the deflection amplification factor given in Table D-1 (3.5 for diagonal strap panels).
I = the importance factor given in Table D-1 (1.0 for the barracks building).
Values for the design story drifts are given in Table D-5.
Long Long Number Long Dir Long Dir
Direction Seismic Dir Height Vertical Frames Lateral Seismic
Total Response Base at Floor Distribution in Long Seismic Story
Panel Weight Coefficient Shear Level Factor Dir Force/frame Shear
Level W
L
C
s
V
L
h
xS
or h
xL
C
vxL
n
L
F
xL
V
xL
(k-mass) (g) (kips) (ft) (kips) (kips)
Roof
3rd 247 27.042 0.271 2 42.713 42.713
Cumulative 247
2nd 647 18.583 0.488 2 76.983 119.696
Cumulative 894
1st 653 9.125 0.241 2 38.110 157.806
Cumulative 1547 0.204 316
CEMP-E TI 809-07
30 November 1998
D-8
Table D-5. Diagonal Strap Design in the Short Direction.
6
Increases in design story drift, related to P-delta effects are now evaluated. P-delta effects do not
need to be considered if the stability coefficient, is equal to or less than 0.10. The stability
coefficient, is defined in Equation C-30 and values are given in Table D-5. These values are well
below 0.10, so design story drifts do not need to be increased. Values of design story drifts, must
be less than the allowable story drifts,
a
given in Table 3-2. For the barracks building this may be
expressed as follows (from Table 3-2):
H 020 . 0
a
= (Eq D-22)
Values of design story drift, and allowable story drift,
a
are given in Table D-5 for each floor level
for the trial panels in the short direction of the barracks building. The values in Table D-5 show that
design story drifts fall below allowable drifts by almost a factor of 3. Therefore these trial sizes meet
the drift requirements.
D10. COLUMN DESIGN. Columns are either built-up from studs (Panel A configuration) or are
structural tubes (Panel D). The columns built up with cold-formed steel studs must have the studs
oriented to form a closed cross-section as shown on Drawings A1 and A2 in Appendix B. Individual
studs must be welded to each other with a weld thickness equal to the thickness of the studs. The
welds are intermittent, with a length and spacing that will ensure composite behavior of the columns.
Structural tubing columns consist of a single tube, which is a closed section by itself. This column will
provide greater moment resistance because of the heavier anchorage detail, and will provide a
greater degree of structural redundancy and widening of the shear panel hysteretic performance.
a. Column Applied Loads. Total load applied to the entire building in the short direction is
expressed by Equation C-17, where the effects of gravity load and seismic forces are additive and
diagonal strap overstrength is accounted for. In this example snow loads, S are zero. This equation
can be expressed in terms of the total dead load, D
T
, and live load, L, given in Table D-2, as follows:
E 0 T DS
Q L 5 . 0 D ) S 2 . 0 2 . 1 ( + + + (Eq D-23)
The loads expressed in Equation D-23 are now divided between the number of frames that make up
the short-direction lateral-load-resisting system. The barracks building has a total of nine such
frames. The loads are distributed based on the tributary area of each frame. Because the end bays
have only half the tributary area, the loads are divided by the number of frames minus one, or also
stated as the number of bays as seen in Table D-6. The vertical load resisting members are the
shear panel columns and individual studs, and these are distributed fairly uniformly in plan throughout
the building. It is assumed that vertical loads are distributed to these studs in proportion to their area,
because of the uniform distribution of columns and individual studs in throughout the building in plan
(normally gravity loads would be distributed based on tributary area).
6
Asterisk designates selected straps.
Strap Yield Strap Design Lat Defl Applied Elastic Defl Design Allow
Panel Panel Strap Strap Strap Initial Lat Stress Lat Yield Shear at Strap Story Lateral Amp Import Story Stability Story
Width Height Faces Width Thickness Stiffness of Strap Capacity Strength Yielding Shear Defl Factor Factor Drifts Coeff Drifts
W H n
s
b
s
t
s
k
s
F
sy
Q
sy
t
Q
sy sy
V
xS xe
C
d I
a
(in) (in) (#) (in) (ga) (in) (k/in) (ksi) (k) (k) (in) (kips) (in) (in) (in)
3rd Floor 132 101.5 1 4 14 0.0747 41 33 7.8 7.4 0.239 6.71 0.205 3.5 1.0 0.718 0.0008 2.03
3rd Floor* 132 101.5 2 4 18 0.0478 53 33 10.0 9.5 0.239 6.71 0.160 3.5 1.0 0.561 0.0006 2.03
2nd Floor 140 113.5 2 6 14 0.0747 112 33 23.0 21.8 0.264 18.52 0.213 3.5 1.0 0.745 0.0015 2.27
1st Floor 140 109.5 2 6 12 0.1046 161 33 32.6 31.0 0.257 24.38 0.192 3.5 1.0 0.672 0.0020 2.19
1st Floor* 140 109.5 2 8 14 0.0747 154 33 31.1 29.5 0.257 24.38 0.201 3.5 1.0 0.705 0.0021 2.19
1st Floor 140 109.5 2 6 14 0.0747 115 50 35.3 33.5 0.389 24.38 0.269 3.5 1.0 0.94 0.0029 2.19
CEMP-E TI 809-07
30 November 1998
D-9
Trial column stud sizes are selected as summarized in Table D-7. Each frame has two shear panels
in the short direction of the building, and each shear panel has two columns so that the 1
st
, 2
nd
and 3
rd
floor columns have four, three and two studs, respectively. This table also summarizes the size of
individual studs for the purpose of determining the area of the column studs relative to all other studs.
The individual studs include the interior studs inside the shear panels plus all additional individual
studs making up the bearing walls in this short-direction frame of the building.
Table D-6. Gravity Load Calculations.
Table D-7. Trial Stud Sizes and Quantities for One Short-Direction Frame.
Number of Column Studs Level Size of Column Studs
Short
Direction
Long
Direction
Size of Individual
Studs
Number of
Individual
Studs
3
rd
Floor 2 x 6 x 48 mil (18 ga) 8 8 2 x 6 x 30 mil (22 ga) 68
2
nd
Floor 2 x 6 x 75 mil (14 ga) 12 12 2 x 6 x 36 mil (20 ga) 68
1
st
Floor 2 x 6 x 75 mil (14 ga) 16 16 2 x 6 x 36 mil (20 ga) 68
Table D-6 summarizes the area calculations based on the trial stud sizes. This table shows that 25,
21, and 14% of the total gravity load in the tributary area of one short-direction frame is carried by the
short direction shear wall columns. The remaining gravity loads are carried by individual studs and
shear panel column studs in the long direction of the building. These gravity loads are summarized in
Table D-6.
The
0
Q
E
, term in Equation D-23 accounts for material overstrength in the diagonal straps. The
vertical component in the straps will place additional compressive loads in the columns. The total
column axial load at the maximum ultimate stress in the diagonal straps, P
vumax
, is determined from
Equation 3-5, and is repeated below:
+
+ =
2 2
s s s max su
max
max vu
W H
H
t b n F
2
GL
P (Eq D-24)
Table D-8 gives values for P
vumax
for each trial shear wall column at each floor in the short-direction
frame of the barracks building.
b. Column Axial Capacity. Table D-8 also presents trial column configurations defined in
terms of their yield stress, F
cy
, column stud or structural tubing material thickness, t
c
number of studs
per column, panel thickness, b
c
and column depth, h
c
. The panel thickness is the column width in the
out-of-plane direction of the panel and column depth is the column width in the in-plane direction of
the panel. Each of the column studs are 6 inches deep with a 2 inch wide flange. They are welded
together to form a closed column section and are oriented so that the stud flanges are parallel to the
plane of the shear panels (see Panels A1 and A2 in Appendix B). In this orientation, the column
depth, h
c
is simply the number of studs per column times 2 inches. Table D-9 presents the column
Total Total Short # Studs # Studs Area/ Area of # Ind Stud Area/ Area of % Gravity Gravity Gravity
Dead Floor Dir # in Short in Long Column Short in Short Indiv Indiv & Carried by /Frame /Frame
Panel S
DS
Load Live of bays Dir Col Dir Col Stud Dir Col & Long Stud Long Dir Short Dir Short Dir Short Dir
Level D
T
=D+EW+IW Load, L n
S-1
A
s
A
cS
Dir A
s
Col Studs Columns GL
max
GL
min
(g) (kips) (kips)
(in
2
) (in
2
) (in
2
) A
I&cL
(in
2
) (%) (kips) (kips)
3rd 0.82 228 0 8 8 8 0.478 3.82 68 0.299 24.16 14% 5.3 2.9
Cumulative 228 0 5.3 2.9
2nd 0.82 507 403 8 12 12 0.747 8.96 68 0.359 33.38 21% 23.6 9.9
Cumulative 736 403 29.0 12.8
1st 0.82 511 403 8 16 16 0.747 11.95 68 0.359 36.36 25% 27.8 11.6
Cumulative 1247 807 56.8 24.4
CEMP-E TI 809-07
30 November 1998
D-10
capacity calculations. This table gives the column nominal areas, A
c
, distance to the extreme fiber, c,
in-plane and out-of-plane moments of inertia and radius of gyration. The columns are conservatively
assumed to be pinned at their tops and bottom (limited moment resistance when the full axial load is
applied) so that the effective length factor, K is 1.0.
Table D-8. Column Design for Cold-Formed Steel Shear Panels Barracks Example.
7
Table D-9. Column Capacity Calculations for Shear Panels Barracks Example.
8
The last row in Table D-8 and D-9 is for a panel with columns made up of 6 x 6 x 3/16 inch structural
tubing members (Panel D configuration). The tubing material is ASTM A500 Grade B, with minimum
(design) yield stress, F
cy
and minimum ultimate stress, F
cu
values of 46 ksi and 58 ksi, respectively.
Similar to the column studs, it is assumed that 1.5 inch wide holes will be drilled through the faces of
the column that are out-of-plane to the shear panel. These holes are for conduit.
The elastic flexural stress, F
e
shown in Table D-9 is calculated based on Equation C-39, and,
c
is
calculated based on Equation C-38. The nominal axial stress, F
n
is then calculated based on either
Equation C-36 or C-37, depending on the value of
c
.
The effective areas, A
e
, of the columns are calculated according to Equation C-41. Values of the
terms used to define this area are also given in Table D-9. Finally, the column design strength, P, is
calculated according to Equation C-35. Values of P are given in Table D-9 for each trial column.
Through an iterative process in the spreadsheet program, trial column configurations were defined
where P exceeds the column axial load at the maximum ultimate stress in the diagonal straps, P
vumax
.
From these results the column configurations marked with an asterisk in Table D-8 and D-9 were
selected for the three floor levels
9
.
7
Asterisk designates selected columns.
8
Asterisk designates selected columns.
9
The second floor panel shown in these tables is not marked with an asterisk because the panel anchors are inadequate,
which may require an increase in column stud thickness, tc.
Diagonal Max Ult Number Max Gravity Column Column Column Number Panel Col Stud
Strap Ult Strap of Shear Load/ Axial load Yield Ultimate Column of Studs Thickness Flange Column
Stress Stress Panels Panel at Strap Ult Stress Stress Thickness /Column /Column Width Depth
F
u
F
sumax /Frame
GL
max
P
vumax
F
cy
F
cu
t
c n
b
c
b
f
h
c
(ksi) (ksi) (kips) (k) (ksi) (ksi) (ga) (in) (in) (in) (in)
3rd Floor 45 68 2 2.66 13.6 33 45 16 0.0598 2 6.0 2.0 4.0
3rd Floor* 45 68 2 2.66 17.1 33 45 14 0.0747 2 6.0 2.0 4.0
2nd Floor 45 68 2 14.48 45.3 50 65 14 0.0747 3 6.0 2.0 6.0
1st Floor 45 68 2 28.38 66.4 50 65 12 0.1046 3 6.0 2.0 6.0
1st Floor* 45 68 2 28.38 63.9 50 65 12 0.1046 4 6.0 2.0 8.0
1st Floor 65 81 2 28.38 59.1 46 58 0.1875 1 6.0 6.0 6.0
Nominal Distance In-Plane Out-of-Plane Eff Elastic Nominal Knockout Eff Column
Column to Extreme Mom of Radius of Mom of Radius of Length Flexural Axial hole Flat Slenderness Eff Column Design
Area Fiber Inertia Gyration Inertia Gyration Factor Stress Stress dia Width factor Width Area Strength
A
c c I
x
r
y
I
y
r
x K F
e
c
F
n
d
h w b A
e P
(in
2
)
(in)
(in
4
)
(in)
(in
4
)
(in) (ksi) (ksi) (in) (in)
(in
2
)
(kips)
3rd Floor 1.20 2.00 3.37 1.68 6.25 2.29 1 78 0.65 27.66 1.5 5.761 1.565 2.40 0.794 18.7
3rd Floor* 1.49 2.00 4.16 1.67 7.74 2.28 1 77 0.65 27.61 1.5 5.701 1.239 2.82 1.063 24.9
2nd Floor 2.24 3.21 10.72 2.19 11.61 2.28 1 106 0.69 41.06 1.5 5.701 1.511 2.43 1.508 52.6
1st Floor 3.14 3.21 14.80 2.17 15.99 2.26 1 113 0.67 41.52 1.5 5.582 1.062 3.04 2.34 82.6
1st Floor* 4.18 4.00 32.40 2.78 21.31 2.26 1 122 0.64 42.09 1.5 5.582 1.069 3.02 3.114 111.4
1st Floor 4.27 3.00 23.8 2.36 23.8 2.36 1 133 0.59 39.80 1.5 5.250 0.546 3.75 3.708 125.4
CEMP-E TI 809-07
30 November 1998
D-11
c. Column Bending and Composite Behavior. The shear panel anchor guidance will provide
moment resistance at the column ends, especially when no axial load is applied to the columns. The
columns built up from studs must be designed to act as a composite cross-section. Table D-10 gives
the intermittent weld length, L (2 inches for each built-up column in Table D-10) and maximum center-
to-center intermittent weld spacing, s
max
needed to ensure composite behavior of the columns. This
is based on Equation 3-9. Based on the values of s
max
given in Table D-10, actual weld spacing is
selected that round down to the nearest full inch from the values given in Table D-10. These welds
are made between all studs in the column and begin at both ends of the columns.
d. Column Combined Axial and Moment Capacity. The combination of axial and bending
load is evaluated for each trial shear panel. For each case, an interaction value is determined
according to Equation 3-10. Table D-10 shows that the interaction values, I fall below 1.0 for all
columns in this example.
Table D-10. Column Intermittent Weld Design, and Combined Axial and Moment Capacity.
e. Column Shear Capacity. The column design shear capacity, V
C
is calculated according
Equation C-46 for each trial column. The values are shown in the second column of Table D-11.
These are below the strap maximum estimated ultimate lateral capacity (P
humax
=
0
Q
E
) calculated
according to Equation 3-24, with values given in the third column of Table D-11. Therefore, the
additional shear capacity from anchors is needed to resist the maximum lateral force, as shown in
Paragraph 12a.
D11. DIAGONAL STRAP-TO-COLUMN CONNECTIONS. Diagonal strap-to-column connections are
designed to resist the maximum estimated ultimate force in the strap, P
su
defined by Equation 3-15.
Values of P
su
are given in the second column of Table D-12 for each panel.
a. Screwed Fastener Connection Design. All screws used in this example are #10 self-
tapping hex head screws, as this is the largest practical size that will not interfere with drywall
installation. The nominal screw diameter, d for #10 screws is 0.190 inches.
10
The following fastener
layout guidance is based on the Screwed Fastener Connection Design guidance in Chapter 3,
Paragraph 9a:
10
AISI Specification Commentary, Table C-E4-1.
Max Area on Distance Mom of Weld Intermittent Strap Max Est Applied Column Column
Column 1 Side of to Neutral Column Shear/ Weld Max o.c. Max Yield Lat Defl Moment Nominal Interaction
Shear Crit Weld Axis Area Length Length Spacing Stress at Strap @
symax Moment
V
cm A y Q q L
s
max
F
symax Yield
M
a
M
nx I
(kips)
(in
2
)
(in)
(in
3
)
(k/in) (in) (in) (ksi)
symax
(in) (k-in) (k-in)
1.1 0.60 1.60 1.0 0.3 2.0 14.3 66 0.478 33.7 55.6 0.952
1.4 0.75 1.60 1.2 0.4 2.0 14.3 66 0.478 41.8 68.7 0.954
2.9 1.49 1.61 2.4 0.7 2.0 12.1 66 0.528 100.4 191.9 0.928
4.2 2.09 1.62 3.4 1.0 2.0 11.7 66 0.514 144.4 265.2 0.967
7.4 2.09 2.20 4.6 1.1 2.0 10.7 66 0.514 274.3 405.0 0.983
75 0.584 236.0 364.9 0.947
CEMP-E TI 809-07
30 November 1998
D-12
Table D-11. Column and Anchor Shear Design.
Table D-12. Screwed Connection Design.
Minimum distance between centers of fasteners is 3d = 0.57 inches.
Minimum distance from centers of fasteners to edge of connected part is 3d = 0.57
inches.
For connections subjected to shear forces in only one direction, the minimum distance
from centers of fasteners to the edge of a connected part perpendicular to the force is
1.5d = 0.29 inches.
The design shear and pull-over per screw, P
s
shall be calculated according to Equations C-47
through C-53 based on the thicknesses of the connected members. Table D-12 gives the ratio of t
2
/t
1
and the resulting design shear per screw as defined by these equations. A screw head diameter, d
w
of 0.402 inches
11
is used for the #10 hex head screws.
Finally, the number of screws required at each diagonal strap-to-column connection, n
screws
is
calculated according to Equation 3-16 for each trial panel configuration. These quantities are given in
Table D-12.
Ultimate shear values from the manufacturers data
12
, P
u
based on the smaller thickness of the
members being connected are used to calculate a nominal screw shear strength, P
ns
according to the
following equation:
25 . 1
P
P
u
ns
= (Eq D-25)
11
This dimension was measured from #10 hex washer head screws (ITW Buildex Part Number 1129000) used in test panels at
USACERL. Measurement was made using a Vernier caliper and the diameter at the base of the washer head was consistently
0.402 inches 0.004 inches (10.2 mm 0.1 mm).
12
From ITW Buildex Catalog for #10 fasteners with #3 drill point.
Column Strap Yield Anchor Total
Shear Lat Ult Stress of Angle Shear Shear
Strength Capacity Angle Thickness Strength Strength
V
C
P
humax
=
0
Q
E
F
yA
t
A
V
A
V
T
(kips) (kips) (ksi) (in) (kips) (kips)
3rd Floor 4.7 16.0 36 0.250 32.4 69.5
3rd Floor* 11.8 20.5 36 0.250 32.4 76.6
2nd Floor 26.9 47.0 36 0.250 32.4 91.7
1st Floor 37.7 66.7 36 0.250 32.4 102.5
1st Floor* 50.2 63.5 36 0.250 32.4 115.0
1st Floor 62.1 57.4 36 0.500 64.8 191.7
Max Est Nominal Diagonal Strap-to-Column Conn Design Number
Ult Strap Screw Strap/Col Tilting Bearing
1
Bearing
2
Nominal Screw Nominal Manufacturer's Shear Screws
Force Dia Thickness Eq C-48 Eq C-49&51 Eq C-50&52 Shear head dia Pull-over Nom Shear /Screw /Face
P
su d Ratio P
ns
P
ns
P
ns
P
ns
d
w
P
nov
P
ns
P
s
n
screws
(kips) (in) (t
2
/t
1
) (kips) (kips) (kips) (kips) (in) (kips) (kips) (kips) (#)
3rd Floor 20.2 0.19 0.80 1.205 1.724 1.380 1.205 0.402 2.027 1.232 0.602 33
3rd Floor* 25.8 0.19 1.56 1.682 1.103 1.724 1.103 0.402 1.297 1.013 0.506 25
2nd Floor 60.5 0.19 1.00 2.430 1.724 2.491 1.724 0.402 2.027 1.242 0.621 49
1st Floor 84.7 0.19 1.00 4.026 2.415 3.488 2.415 0.402 2.838 1.242 0.621 68
1st Floor* 80.7 0.19 1.40 4.026 1.724 3.488 1.724 0.402 2.027 1.242 0.621 65
1st Floor 72.8
CEMP-E TI 809-07
30 November 1998
D-13
Equation D-25 is not included in the guidance in Chapter 3 or Appendix C because the format of
manufacturers test data is unknown and may need to be evaluated on a case-by-case basis as
shown in this example. Table D-12 provides values for this nominal shear strength based on
manufactures fastener shear strength and Equation D-25. If these values are less than other
nominal values based on equations C-48 through C-53, these values will control and will be used in
Equation C-47 to calculate the design shear per fastener, P
s
. Table D-12 presents P
s
based on the
overall minimum nominal shear or pull over strength. In this example problem the manufacturers
fastener shear strength data controls the nominal fastener shear strength for all panel configurations
except for the one shown on the first row of Table D-12.
The number of screws at each diagonal strap-to-column connection, n
screws
, shown in Table D-12, is
very large and the use of larger screws or a welded connection should be considered. Still, each of
these connections may be constructed within the overlap area of the strap and column and within the
spacing and edge distance requirements given above. The most difficult joint to lay out is the one in
the first row, which is based on installing diagonal straps on only one face of the shear panels. The
column is 4 inches wide and the strap is also 4 inches wide and is oriented at an angle based on the
width, W and height, H of the overall panel given in Table D-5. A layout of the fasteners is selected
that will keep the column critical shear plane as close as possible to the track, while maximizing the
net area for rupture strength evaluation. A trial layout is shown in Figure D-4. This connection has 5
fasteners at the first row against the track, and 6, 6, 6, 6, 6 and 5 fasteners in the subsequent rows
moving away from the joint. These fasteners are spaced at 9/16 inches on center horizontally and
inch on center vertically. The other diagonal strap-to-column screwed connections in Table D-12 are
laid-out in a similar manner and are shown in Figures D-5 D-8.
b. Design Rupture Strength Between Fasteners. Figures D-4 through D-8 show the critical
diagonal strap rupture surface, for which the rupture strength is calculated. The rupture surface
located along the inside edge of the column and along a horizontal plane will be loaded at
approximately a 45 degree angle to the rupture surface. Therefore the average of the shear strength
and tensile strength expressed by Equations 3-17 and 3-18 are used for determining the design
shear/tension strength, VT along this surface as follows:
nvt u vt
A F 8 . 0 VT = (Eq D-26)
Where:
vt
= the shear tensile rupture resistance factor, equal to 0.75
A
nvt
= the net area subjected to load at approximately 45 degrees.
The design shear/tension, VT and tensile, T rupture strengths are calculated according to Equations
D-26 and 3-18, based on a trial layout of the fasteners in each diagonal strap-to-column connection.
The use of #10 screws result in a very large number of screws at each connection as seen in Table
D-12 and Figures D-4 through D-8. The screw pattern must stay within the spacing and edge
distance limitations given above.
When the strap-to-column rupture strength is evaluated based on Equation 3-19, as modified with
Equation D-26 the resistance factors in Equations D-26 and 3-18 may be increased to 1.0, because
of the ASTM minimum material requirement on F
u
/F
y
. All of the trial diagonal strap-to-column
connections do not meet Equation 3-19, as can be seen by comparing P
sy
and (VT + T)n
s
in Table D-
13. The achieved resistance factor (
a
) for Equation D-26 and 3-18 is shown in Table D-13 for each
of these connections. This achieved resistance factor is expressed as follows:
) A A 8 . 0 ( F n
P
nt nvt u s
sy
a
+
= (Eq D-27)
This factor is well below 1.0 for all connections except the first row (3
rd
Floor case with a diagonal
strap on only one face of the panel). The shear panel shown in the first row (Figure D-4) is therefore
an unacceptable configuration, and the design shown in the second row (Figure D-5) is selected for
CEMP-E TI 809-07
30 November 1998
D-14
the 3
rd
floor shear panels. For the other shear panels the resistance factors are above 0.75, but are
judged to be acceptable because of the ATSM requirement on F
u
/F
y
.
Table D-13. Screwed Connection Rupture Strength and Welded Connection Design.
c. Welded Connection Design. Figure D-9 shows a trial layout of a welded diagonal strap-to-
column connection. All welds in this connection have a thickness, t equal the thickness of the
diagonal strap (0.075 inches). This is much less than 0.15 inches, so weld failure through the weld
throat (Equation C-57) need not be considered. Details on the strap and column sizing are given in
the last row of Tables D-5 and D-8. All welds have a L/t ratio much greater than 25, so that Equation
C-55 is used to define the longitudinal weld capacity. The top edge of this connection shown in
Figure D-9 is loaded in the longitudinal direction and its design shear strength is defined according to
Equation C-55. The diagonal edges at the end of the diagonal strap are loaded close to 45 degrees,
so that an average of Equation C-55 and C-56 defines the weld capacity along these edges.
Therefore, the longitudinal/transverse design shear strength (P
LT
) may be expressed as follows:
u LT
tLF 87 . 0 P = (Eq D-28)
Where:
= 0.58, which is an average of the resistance factors for longitudinal and transverse loading
expressed in Equations C-55 and C-56.
Table D-13 gives the weld thickness, length of welds loaded in the longitudinal and
longitudinal/transverse directions. Table D-13 also gives the design capacity of the longitudinal,
longitudinal/transverse and combined capacity ((P
L
+ P
LT
)n
s
) expressed by Equation 3-21, as modified
by Equation D-28. Comparing the total shear capacity and strap yield strength, P
sy
shows that this
connection detail meets the requirements of Equation 3-21.
D12. SHEAR PANEL ANCHORS. Panel anchors must be installed on both sides of the shear panel
columns. These anchors are installed at both the top and bottom of the columns to anchor the panels
to the floor diaphragms both above and below the shear panels. The anchors are needed to provide
the required shear, uplift and moment resistance from the eccentric diagonal strap loading of the
anchors. The anchors will also provide limited moment resistance that will allow some moment frame
action of the columns, providing system redundancy and a widening of the hysteretic load/deflection
envelope. The anchors consist of angle iron sections welded to the column, with loose steel plates
that are both bolted to the diaphragm using embedded anchor bolts (see Figures D4 through D9).
a. Anchor Shear Capacity. All of the trial columns shown in Table D-8 have insufficient
shear capacity by themselves and require additional shear capacity from their anchorage. The
anchor angle irons increase the shear capacity. Each angle leg extends beyond the critical shear
plane. Figure D-4 shows such an anchorage made up with 6 inch long, L 4 x 4 x inch angle iron
sections welded to both sides of each column. The anchor shear capacity is defined according to
Equation 3-22, and the combined column and anchor shear capacity is defined according to Equation
Strap Tension Tension Design Achieved Fillet Longitudinal Weld Long/Trans Weld Welded
Yield /Shear Net Rupture Resistance Weld Design Design Conn Total
Force Net Area Area Strength Factor Thickness Length Strength Length Strength Capacity
P
sy
A
nvt
A
nt
(VT+T)n
s
a t L
P
L L
P
LT
(P
L
+P
LT
)n
s
(kips)
(in
2
) (in
2
)
(kips) (in) (in) (kips) (kips) (kips)
3rd Floor 9.9 0.218 0.028 6.8 1.082
3rd Floor* 12.6 0.044 0.134 11.5 0.825
2nd Floor 29.6 0.153 0.269 26.4 0.840
1st Floor 41.4 0.312 0.259 34.3 0.906
1st Floor* 39.4 0.288 0.299 35.7 0.828
1st Floor 44.8 0.0747 6.25 12.5 8.75 21.4 67.9
CEMP-E TI 809-07
30 November 1998
D-15
3-23. The column shear capacity, V
c
was determined in Paragraph D10e according to Equation C-
46. Table D-14 shows the yield stress, width and thickness of the angles used in these anchors, so
that the combined shear strength of the columns and angles V
T
exceed P
humax
(Equation 3-23). Table
D-11 shows that combined shear strength V
T
exceeds P
humax
for all the trial shear panels.
b. Shear Panel Anchor Angle and Plate Design. The most critical load condition for anchors
is when the effects of gravity load and seismic forces counteract each other, as expressed by
Equation C-18.
Column-to-angle welds and angle sizes are selected for each trial configuration based on the
guidance in Tables 3-3 and 3-4. For each case, the maximum weld thickness and angle thickness is
selected. These sizes are shown in Table D-14 and Figures D-4 through D-9. For each trial anchor,
a plate must be added as shown in Figures D-4 through D-9 (and Table D-14), to provide adequate
uplift resistance. These plates will also add moment resistance. Anchor angles and plates are
designed following the requirements of Equation 3-25, as shown in Table D-14 and D-15.
The capacity of the vertical column-to-angle welds at the corner of the columns assume double shear
(Equation C-59), because the effective thickness of this grove weld should be at least twice the
thickness of the column material. This is because of the curvature of the column corner that the
grove weld will fill. The anchor must provide moment resistance for the moment from the eccentric
loading of the diagonal strap, accounting for the maximum estimated yield overstrength of the strap
(P
symax
L
s
). Any moment capacity beyond this is not required (i.e., P
cb
in Equation 3-31 may equal
zero), but will provide beneficial column moment resistance. However, at any load condition at least
one column will have little axial load and no diagonal strap load, so that the anchors will provide
significant moment resistance to provide some moment frame capacity in the shear panel.
Table D-14. Shear Panel Anchor Angle and Plate Design.
The panels in Rows 3 and 4 fail to meet the requirement of Equation 3-25, as can be seen in Table D-
15. Row 3 (2
nd
Floor shear panels) is the worst case where the column-to-angle weld design
strength, P
A
is 3% below the applied load, based on the maximum estimated yield stress of the
diagonal straps. This shear panel must be redesigned, which can be done by increasing the
thickness of the column material as the strength of the welds are directly proportional to the thickness
of the thinner material (see Equations C-56 and C-59). The shear panel shown in Row 5 meets the
requirement of Equation 3-25 for the 1
st
Floor shear panel and this panel is selected for the 1
st
Floor.
Min Gravity Anchor Col/Anchor Anchor Angle Plate Angle
Load/ Uplift @ max Weld Yield Thickness Moment
Panel Strap Yield Thickness Stress Size Capacity
GL
min
P
vymax
t
w
F
yA
H
A
W
A
t
A k
t
p
M
A
(kips) (kips) (in) (ksi) (in) (in) (in) (k-in)
3rd Floor 1.44 11.3 0.125 36 L 4 x 4 x 0.25 0.625 0.375 9.87
3rd Floor* 1.44 14.7 0.125 36 L 4 x 4 x 0.25 0.625 0.438 12.34
2nd Floor 6.38 34.1 0.125 36 L 4 x 4 x 0.25 0.625 0.563 18.41
1st Floor 12.21 44.9 0.125 36 L 4 x 4 x 0.25 0.625 0.688 26.01
1st Floor* 12.21 42.5 0.125 36 L 4 x 4 x 0.25 0.625 0.625 22.02
1st Floor 12.21 35.3 0.188 36 L 6 x 6 x 0.50 1.000 0.750 39.49
CEMP-E TI 809-07
30 November 1998
D-16
Table D-15. Shear Panel Anchor Angle and Plate Design (continued).
Table D-16 presents the anchor (or column) moment capacity as defined by Equation 3-30. Much of
this capacity is used to resist the maximum estimated applied moment from the eccentric loading of
the diagonal strap (P
symax
L
s
). The uplift capacity per angle that remains to resist column bending, P
cb
should be greater than zero. Table D-16 shows that the panels in Rows 3 and 4 have values slightly
below zero. The panel in Row 3 shall be redesigned as stated earlier and the panel in Row 5 is
selected for the 1
st
Floor as stated earlier.
c. Shear Panel Anchor Bolt Design. Finally the anchor bolts that fasten the shear panels to
the reinforced concrete beam or slabs are designed. The same detail is used at both the top and
bottom of the columns. The anchor bolts are sized based on the bolt shear strength, P
v
, tensile
strength, P
t
and cone failure strength, P
c
. Table D-16 and Figures D-4 through D-9 show that two
ASTM A-325 anchor bolts are cast into the concrete on both sides of the columns at each anchor, for
a total of four bolts per anchor, n
AB
. The anchor bolts would be positioned with a template before the
concrete is cast. Alternatively, the same bolts that anchor the top of one panel could extend through
the concrete to anchor the bottom of the panel above.
Table D-16. Anchor Moment and Anchor Bolt Shear Design.
The design anchor bolt shear strength, P
v
must exceed the applied shear load P
hAB
(Equation 3-33).
Values of P
v
, based on Equation 3-34 are given in Table D-16 for each trial panel. In every case
these values exceed P
hAB
. The design tensile strength, P
t
and cone failure strength, P
c
must exceed
the tensile stress per bolt, P
tAB
. Values for P
t
, based on Equation 3-35 and P
c
, based on Equation C-
60 are given in Table D-17 for each trial panel. In every case these values exceed P
tAB
. The
embedment lengths for the anchor bolts, l
AB
shown in Table D-17 are very large. If possible the same
anchor bolts should rather extend through the concrete beam or slab to the shear panel above or
below, thus anchoring the anchor bolts. The minimum edge distance, m to prevent side cone
concrete failure is defined based on Equation C-63 and values are given in the last column of Table
D-17. Figures D-4 through D-9 show the trial anchor design for each row in Tables D-14 through D-
17. For each floor level the asterisk indicates the selected panel design.
Distance from Anchor Bolts to: Tensile Tensile Angle Angle Angle
Column Bolt Nut Crit Bending Force Force/ Horiz Weld Vert Weld Tot Weld
Face Width Plane Avail/angle Angle Strength Strength Strength
d
c
W
d
b
P
M
P
vymax
/2+P
M
P
T
P
G
P
A
(in) (in) (in) (kips) (kips) (kips) (kips) (kips)
3rd Floor 2.5 1.44 1.16 11.42 17.08 9.69 17.76 27.45
3rd Floor* 2.5 1.44 1.16 14.01 21.34 12.10 11.09 23.19
2nd Floor 2.5 1.63 1.06 17.63 34.66 17.48 16.02 33.50
1st Floor 2.6 1.81 1.09 25.09 47.56 24.48 22.44 46.91
1st Floor* 2.5 1.81 0.97 24.22 45.46 24.48 22.44 46.91
1st Floor 3.5 1.81 1.59 31.90 49.55 39.15 53.83 92.98
Column Strap Moment Angle Anchor Applied Bolt Nom Bolt Shear
Moment Max Yield Arm of Uplift for # Anchor Bolt Shear/ Shear Design
Capacity Strength Dia Strap Col Bending Bolts/col Dia Bolt Strength Strength
M
c
P
symax
L
s
P
cb
n
AB
d
AB
P
hAB
F
v
P
v
(k-in) (kips) (in) (kips) (in) (in) (kips) (ksi) (kips)
3rd Floor 55.69 19.72 1.60 4.95 4 3/4 4.00 60 19.88
3rd Floor* 68.31 25.24 2.00 3.66 4 3/4 5.12 60 19.88
2nd Floor 121.21 59.16 2.10 -0.44 4 1 11.75 60 35.34
1st Floor 172.51 82.84 2.40 -3.83 4 1 1/8 16.68 60 44.73
1st Floor* 214.93 78.88 2.20 4.66 4 1 1/8 15.89 60 44.73
1st Floor 239.22 67.23 2.20 12.17 4 1 1/8 14.34 60 44.73
CEMP-E TI 809-07
30 November 1998
D-17
Table D-17. Anchor Bolt Tensile and Cone Failure Design.
D13. SUMMARY OF EXAMPLE DESIGN PROBLEM RESULTS. The trial shear panel for the 2
nd
Floor of the barracks building must be re-designed for the column-to-anchor weld detail. Figures D-5
and D-8 show the details for the selected panels. Details for the entire panels are given in Tables D-5
and D-8 through D-17.
Bolt Nom Bolt Tensile Out-of-plane Anchor Bolt Stress Concrete Cone Min
Tensile Design Force/ Space btw Embedment Cone Compressive Design Edge
Strength Strength Bolt Bolts Length Area Strength Strength Distance
F
t
P
t
P
tAB
d
c-c
l
AB
A
c
f'
c
P
c m
(ksi) (kips) (kips) (in) (in) (in2) (psi) (kips) (in)
3rd Floor 90 29.82 22.06 3.5 6.0 110 4000 23.58 3.31
3rd Floor* 90 29.82 27.57 3.5 7.0 143 4000 30.86 3.31
2nd Floor 90 53.01 44.77 3.5 9.0 224 4000 48.27 4.42
1st Floor 90 67.10 67.01 3.0 11.0 315 4000 67.84 4.97
1st Floor* 90 67.10 58.73 3.0 10.0 265 5000 63.61 4.70
1st Floor 90 67.10 56.99 3.0 10.0 265 5000 63.61 4.70
CEMP-E TI 809-07
30 November 1998
D-18
Figure D-1. Design response spectrum for Fort Lewis, Washington barracks building.
Figure D-2. Schematic drawing of barracks building example.
CEMP-E TI 809-07
30 November 1998
D-19
Figure D-3. Barracks building short direction elevation and plan views.
CEMP-E TI 809-07
30 November 1998
D-20
Figure D-4. Example connection/anchorage detail 1
st
row of Tables D-5, D-8 D-17.
CEMP-E TI 809-07
30 November 1998
D-21
Figure D-5. Example connection/anchorage detail 2
nd
row of Tables D-5, D-8 - D-17.
CEMP-E TI 809-07
30 November 1998
D-22
Figure D-6. Example connection/anchorage detail 3
rd
row of Tables D-5, D-8 - D.17.
CEMP-E TI 809-07
30 November 1998
D-23
Figure D-7. Example connection/anchorage detail - 4
th
row of Tables D-5, D-8 D-17.
CEMP-E TI 809-07
30 November 1998
D-24
Figure D-8. Example connection/anchorage detail 5
th
row of Tables D-5, D-8 D-17.
CEMP-E TI 809-07
30 November 1998
D-25
Figure D-9. Example connection/anchorage detail - 6
th
row of Tables D-5, D-8 - D-17.
CEMP-E TI 809-07
30 November 1998
E-1
APPENDIX E
PROTOTYPE SHEAR PANELS FOR COLD-FORMED STEEL SEISMIC DESIGN
(English I-P units only)
E1. INTRODUCTION. This appendix provides tabular data for the selection of possible prototype
shear panels that may be used in the seismic design of cold-formed steel structures. These panels
were developed for an example problem presented in Appendix D using the design guidance
presented in Chapter 3 and Appendix C. Each shear panel given in Table E-1 is defined in Figures
D5, D8 and D9 as indicated in Table E-1.
E2. DEFINITION OF TERMS. The prototype shear panels given in Table E-1 shall be used based
on the following definition of terms:
V
x
= the maximum story shear per shear panel, based on Equation C-27 in Appendix C.
GL
max
= the maximum gravity load per shear panel, based on Equation C-17 in Appendix C.
GL
min
= the minimum gravity load per shear panel, based on Equation C-18 in Appendix C.
E3. PROTOTYPE PANEL LOAD TABLE. Table E-1 provides the tabular data needed to select
prototype shear panels.
Table E-1. Prototype Shear Panel Load Capacities.
V
x
GL
max
GL
min
(kips) (kips) (kips)
Figure D5 9.5 6.0 -13.2
Figure D8 29.5 34.1 -6.5
Figure D9 33.5 44.1 -36.5
CEMP-E TI 809-07
30 November 1998
F-1
APPENDIX F
SEISMIC QUALIFICATION PROCEDURE AND ACCEPTANCE CRITERIA FOR OTHER SHEAR PANEL
CONFIGURATIONS
(English I-P units only)
F1. SCOPE. This appendix presents the test procedure, acceptance criteria and documentation
requirements needed to demonstrate the acceptability of cold-formed steel shear panel configurations
different than the specific system defined in Chapter 3. Acceptable panels are limited to cold-formed
steel shear panels with diagonal straps or full panel sheets as the lateral load resisting elements. The
columns shall be constructed with cold-formed or hot-rolled structural steel. This is for the qualification of
a prototype of the specific panel that will be used in construction. Qualification requires the testing of
three specimens. All panel tests shall represent full panel system tests of all the panel components
including connections, and anchors.
F2. COUPON TESTS OF ALL TEST PANEL MATERIALS. Coupon tests shall be performed on all
materials that may contribute to the structural performance of the test panels. At least three coupons
shall be tested from each lot of each type of material. Coupons shall be prepared and tested following
the provisions of ASTM A 370. Materials that contribute to the ductility of the shear panels shall have a
total elongation of at least 10% for a two-inch long gage length. All coupon test results shall be plotted in
a test report, in terms of stress versus strain. All coupon test results shall also be summarized in a table
in the format shown in Table F-1. The data in this table shall be the average value of the three or more
coupons of the particular component.
Table F-1. Format for Tabular Coupon Test Results.
Structural
Component
of Coupon
Design Yield
Stress
(MPa or ksi)
0.2% Offset*
Yield Strain
(mm/mm)
0.2% Offset *
Yield Stress
(MPa or ksi)
Maximum
Load
Strain
(mm/mm)
Maximum
Stress
(MPa or
ksi)
Max Stress
0.2% Offset
Yield Stress
Component
#1
Component
#2
* See USACERL TR Chapter 4 for definitions of 0.2% offset yield strain and stress
F3. COUPON TEST OF ALL FIELD PANEL MATERIALS. Coupon tests shall be performed on all
materials that contribute to the structural performance of the field panels. The field panels shall be
identical to the prototype-tested panels. At least three coupons of each material shall be tested.
Coupons shall be prepared and tested following the provisions of ASTM A 370. Materials that contribute
to the ductility of the shear panels shall have a total elongation of at least 10% for a two-inch long gage
length. All coupon test results shall be plotted in a test report, in terms of stress versus strain. All coupon
test results shall also be summarized in a table in the format shown in Table F-1. The data in this table
shall be the average value of the three or more coupons of the particular component. The field diagonal
straps or full panel sheets shall have a coupon yield stress (0.2% offset) not greater than 5% above or not
less than 10% below the test panel coupon yield stress (0.2% offset). The field material coupons for all
other structural elements shall have coupon yield stress (0.2% offset) not less than the test panel coupon
yield stress (0.2% offset).
F4. TEST CONFIGURATION. Full-scale test panels shall be tested with both monotonic (pushover in
one direction) and cyclic loading. The panels shall be anchored to a base beam and top beam in a
manner representative of the field installation. The base beam shall resist any slippage, out-of-plane
movement or rotation in any direction. Vertical load shall be applied to the shear panel through the top
beam, at a level representative of potential gravity loads in the field. The amount of vertical load applied
should consider the worst case condition for the most vulnerable panel components. For example, the
CEMP-E TI 809-07
30 November 1998
F-2
minimal vertical load may provide the most severe loading for the anchors, while the maximum vertical
would provide the worst case loading for column buckling. This vertical load shall be held constant
throughout each test. The top beam shall be held horizontal during all tests, as this represents the field
conditions when the panel is assembled in a building. Figure F-1 shows the test configuration and
instrumentation plan for shear panels tested at USACERL in order to illustrate the load configuration. In
the USACERL tests, stroke control was used to keep the two vertical actuators at the same length, which
held the top beam horizontal. The combined vertical force was held constant manually.
Figure F-1. Schematic drawing showing sensor locations.
F5. INSTRUMENTATION. Table F-2 defines the instrumentation required for all shear panel tests.
Figure F-1 shows the location and orientation of all sensors. Table F-2 describes the purpose of each
sensor. The purpose of most gages is to ensure that no unwanted motion takes place and for test
control. The only data used in reporting panel performance are the 1
st
, 2
nd
, 3
rd
and 4
th
channels in Table
F-2. The vertical actuator force measurements (FVS and FVN in Table F-2 and Figure F-1) are required
to defined total shear force when deflections reach large amplitudes, at which point the horizontal
components of these forces become significant. This total shear force, TSF is determined as follows:
'
1
]
1
,
_
L
sin TVF TSF (Eq F-1)
Where:
FH = the measured horizontal actuator force (see Table F-2 or Figure F-1).
TVF = the total vertical actuator force, equal to FVS plus FVN (Table F-2 or Figure F-1).
DH = the measured horizontal displacement (Table F-2 or Figure F-1).
L = the length of the vertical actuators, with the vertical load applied, but not horizontal
displacement.
CEMP-E TI 809-07
30 November 1998
F-3
Table F-2. Cold-Formed Steel Shear Panel Instrumentation.
Note: * Linear Resistance Deflection Gauge, often called a Yo-Yo Gauge.
F6. TEST REQUIREMENTS. For each shear panel qualified, three specimens shall be fabricated and
tested. This assumes only minor variation in panel performance for a given shear panel. If large
variations occur more than three specimens shall be tested and a statistical evaluation of panel
performance may be required. For panels with minor variation, one specimen shall be tested
monotonically and two shall be tested cyclically as defined below. All tests, both monotonic and cyclic
shall use stroke control, loading the panels laterally at a constant displacement per minute. The vertical
load shall be held constant and the top beam shall be held horizontal throughout each test as described
in Paragraph F4, Test Configuration. Both monotonic and cyclic tests shall be conducted up to
deflections that cause ultimate failure of the shear panels, or reach the limits of the test equipment, but
shall not be less than 10 times the lateral yield displacement of the test panel,
y
. These are very large
deflections, well beyond acceptable drift limits, but are needed to ensure that brittle failures (sudden loss
of lateral or vertical load carrying capacity) do not occur near the useful deflection range of the panel.
a. Monotonic Test Protocol. A single specimen of each shear panel shall be loaded in one
direction (monotonic) at a constant stroke rate that is slow enough to allow careful observation of panel
performance and failure progression
1
. These observations shall include documentation of panel behavior
through a log of observations with respect to displacement and photographs. Load versus deflection
(TSF versus DH) shall be plotted to determine the measured lateral yield displacement
y
. This value
shall be used in defining the cyclic test protocol.
b. Cyclic Test Protocol. A minimum of two specimens of each panel configuration shall be
loaded cyclically at a constant stroke rate that is slow enough to allow careful observation of panel
performance and failure progression
2
. These observations shall include documentation of panel behavior
through a log of observations with respect to displacement and photographs. Load versus deflection
(TSF versus DH) shall be plotted to create load/deflection hysteretic envelopes. The cyclic load protocol
follows a standard method, so that test results may be compared with cyclic test results of other systems.
The protocol defined here is similar to SAC2
3
guidelines that have been modified to scale to the lateral
yield deflection as described in ATC-24
4
. The SAC recommended loading histories call for loading with a
1
Monotonic tests conducted at USACERL used a stroke rate of 0.5 inches per minute.
2
Cyclic tests conducted at USACERL used a stroke rate of 3 and 6 inches per minute. The faster stroke rate was used for panels
tested cyclically beyond 10 inches (20 inches peak to peak).
3
SAC Testing Programs and Loading Histories, unpublished guidance, 1997.
4
Applied Technical Council (ATC) 24, Guidelines for Cyclic Seismic Testing of Components of Steel Structures, 1992.
Channel Sensor Measurement, Direction,
# Type Location and Symbol Purpose
1 Load cell Force Horizontal, FH Horizontal actuator load measurement
Deflection Horizontal, DH Horizontal deflection, shear panel deformation
3 Load cell Force Vertical South, FVS Manual vertical load control (25k total load w/#5)
4 LVDT Deflection Vertical South, DVS Stroke (tied to #6)
5 Load cell Force Vertical North, FVN Load (summed with #3, for 25k total load)
6 LVDT Deflection Vertical North, DVN Controlled by #4 stroke feedback
Defl Horiz Bot Track, DHBT To ensure no slippage
Defl Vert South Bot Track, DVSBT To ensure no uplift
Defl Vert North Bot Track, DVNBT To ensure no uplift
LRDG* (20") Defl Horiz Top Track, DHTT Check for shear panel deformation - same as #2
11 LRDG (10") Defl Vert South Top Track, DVSTT Vertical panel/column deformation & rotation check
12 LRDG (10") Defl Vert North Top Track, DVNTT Vertical panel/column deformation & rotation check
CEMP-E TI 809-07
30 November 1998
F-4
deformation parameter based on interstory drift angle, defined as interstory height over interstory
displacement. The commentary to the SAC document explains that the interstory drift angle of 0.005
radians corresponds to a conservative estimate of the value that would cause yield deformation.
Therefore, the load protocol defined by SAC in terms of drift angle are scaled to the measured lateral
yield deflection,
y
to define the cyclic test steps as defined in Table F-3. This protocol calls for a set
number of cycles at each of the deformation amplitudes shown in Table F-3. This protocol is illustrated
by the deformation time history shown in Figure F-2, which is based on a lateral yield deflection,
y
of 0.4
inches and stroke rate of 6 inches per minute.
Table F-3.Cyclic Test Load Protocol.
SAC-2 Load
Step # Number of
Cycles, n
Peak Deformation,
(radians)
Modified
SAC
Amplitude
1 6 0.00375 0.75
y
2 6 0.005 1.0
y
3 6 0.0075 1.5
y
4 4 0.01 2
y
5 2 0.015 3
y
6 2 0.02 4
y
7 2 0.03 6
y
8 2 0.04 8
y
9 2 0.05 10
y
10 2 0.06 12
y
11 2 0.07 14
y
12 2 0.08 16
y
13 2 0.09 18
y
14 2 0.10 20
y
15 2 0.11 22
y
16 2 0.12 24
y
17 2 0.13 26
y
18 2 0.14 28
y
19 2 0.15 30
y
20 2 0.16 32
y
CEMP-E TI 809-07
30 November 1998
F-5
Figure F-2. Modified SAC cyclic test time history with
y
= 0.4 in and 6 in/min stroke rate.
F7. SHEAR PANEL PERFORMANCE DOCUMENTATION. Shear panel performance from both
monotonic and cyclic tests shall be documented in terms of load versus deflection plots (TSF versus DH).
Cyclic tests plot load versus deflection to define load versus deflection hysteretic envelopes.
Observations of panel performance and failure progression with respect to lateral displacement shall be
documented in a tabular or other format. Photographs that document these observations shall be
included in the test report. Test results for each specimen tested shall be summarized as indicated in
Table F-4. Repeatability of panel performance of a given configuration is critical, so that if only two cyclic
tests are conducted the poorest performance of the two shall form the basis for design. Therefore special
consideration shall be given to large variations in panel performance, especially failure type or
displacement amplitude of each type of failure. Test procedures and results shall be documented in a
test report.
Table F-4. Summary of Test Panel Performance.
Test
Specimen
Load Type
(Monotonic
or Cyclic)
Load Rate
(mm/min
or in/min)
Linear Shear
Stiffness
(kN/mm) or
(kips/inch)
Shear Load
at
y
Deflection
(kN or kips)
Shear Deflection
at Ultimate
Shear Load
(mm or inches)
Ultimate
Shear Load
(kN or kips)
F8. DESIGN GUIDANCE. The measured load versus deflection data shall be used to define the design
strength and stiffness of the shear panels. Resistance factors for each loading mechanism shall be
defined that recognizes the variation of the shear panel capacity. In other words a panel shear capacity
resistance factor,
v
, shall reflect the variability of shear capacity of the tested panels. For example,
v
=
0.9 if the strength variability is small and mode and displacement of failures are consistent.
The following criteria shall be defined from the shear panel cyclic test data:
1. The panel ductility, , is the ultimate lateral deflection without loss of lateral or vertical load
capacity,
u
over yield lateral deflection,
y
defined as follows:
y
u
(Eq F-2)
-16
-14
-12
-10
-8
-6
-4
-2
0
2
4
6
8
10
12
14
16
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
Time (mi nut es)
D
i
s
p
l
a
c
e
m
e
n
t
(
i
n
c
h
e
s
)
CEMP-E TI 809-07
30 November 1998
F-6
2. The panel overstrength,
5
, which is the maximum measured ultimate lateral panel capacity, Q
u
over the yield capacity, Q
y
, defined as follows:
y
u
Q
Q
(Eq F-3)
3. The panel redundancy factor,
1
of the individual shear panel tested
6
. This redundancy can be
seen by comparing shear panel load/deflection data with coupon data, to determine if overstrength,
is due to strain hardening of the primary load-carrying element or due to the action of a secondary
lateral load-resisting element. An example of this would be a panel with diagonal straps acting as the
primary element with the columns effectively working to provide a significant moment frame. In this
case the moment frame would provide redundancy for the shear panel. If the diagonal straps fail, this
moment frame capacity would provide lateral resistance for the moment from the P-delta effect of the
gravity load. This redundancy is critical to preventing building collapse for a structure whose lateral
load resisting system has failed. The panel redundancy factor,
1
is calculated as follows:
p
c p
p
u
1
Q
Q Q
Q
Q
+
(Eq F-4)
Where:
Q
p
= the portion of the shear panel ultimate lateral capacity carried by the primary lateral load
resisting element including the effects of strain hardening. For panels with full panel
sheet(s) this contribution will increase with increasing deflection due to a widening of the
panel tension field. This value can only be reasonably determined by measuring Q
c
(as
described below) and calculating Q
p
as the difference between Q
u
and Q
c
.
Q
c
= the portion of shear panel ultimate lateral capacity carried by the columns acting as moment
frames. For panels with full panel sheet(s) this value can only be obtained by testing the
same exact panels with the full panel sheets removed. If these tests are not performed for
full panel sheet shear panels, Q
c
shall be set equal to zero.
4. The width of the cyclic test load/deflection hysteretic envelope. If the hysteretic envelope is
significantly pinched (no or very little load resistance away from the peak excursions), much less
energy is absorbed by the structural system so that building amplification grows. Pinched hysteretic
envelopes occur when the primary lateral load-resisting element is stretched, and there is little
redundant capacity from other elements to pick up load, so that little resistance is available away from
the peak excursions of the load cycles. Panels with significantly pinched hysteretic envelopes, can
experience high acceleration impact loading because the building will be free to sway with little
resistance and then suddenly snap the lateral load-resisting element when another peak excursion is
reached. This high acceleration snap can cause brittle failures. A shear panel with a great deal of
redundancy within the panel,
1
will tend to have a wide hysteretic envelope.
Table F-5 defines the acceptance criteria in terms of , and
1
based on data measured in the cyclic
panel tests, as defined by Equations F-2 through F-4.
Table F-5. Acceptance Criteria for Shear Panels
based on , and
1
.
Criteria Acceptance Requirement
5
This should not be confused with the system overstrength factor, 0 defined in FEMA 302, Section 5.2.2 and Table 5.2.2 or TI
809-07, Equation C-16.
6
This should not be confused with the reliability factor, or x, which is the extent of structural redundancy in the lateral-force
resisting system for an entire story of a building.
CEMP-E TI 809-07
30 November 1998
F-7
Panel Ductility, 10
Panel Overstrength, 1.3
Panel Redundancy factor,
1
1.0
Hysteretic Envelope Width Not Required
Values for the system response modification factor, R system overstrength factor,
0
and deflection
amplification factor, C
d
, are defined in Table F-6. These values are used in the seismic design guidance
defined in TI 809-04 and FEMA 302. Exceptions to this criteria shall require Corps of Engineers
Headquarters (CEMP-ET) approval.
Table F-6. Values for R,
0
and C
d
.
Factor Value
System Response Modification Factor, R 4
System Overstrength Factor,
0
2
Deflection Amplification Factor, C
d
3.5
CEMP-E TI 809-07
30 November 1998
G-1
APPENDIX G
MASONRY VENEER / STEEL STUD WALLS
(NONBEARING CONSTRUCTION)
List of Drawings
Title Drawing No
Wall Anchors
Wire Anchors .................................................................................... 1.1
Wire Anchor, Details.......................................................................... 1.2
Wire Anchor with Continuous Brick Joint Reinforcement .................... 1.3
Pintle Anchor .................................................................................... 1.4
Wall Sections
Typical Brick Veneer and Steel Stud Panel Wall ................................ 2.1
Adjustable Wall Anchor Detail ........................................................... 2.2
Masonry Veneer Steel Stud Panel Wall
Plan View............................................................................. 2.3.1
Foundation Wall Section....................................................... 2.3.2
Structural Steel Section ........................................................ 2.3.3
Reinforced Concrete Section ................................................ 2.3.4
Steel Joist Section................................................................ 2.3.5
Slip Joint Details
Typical Single Track ............................................................. 3.1
Typical Double Track............................................................ 3.2
Parapet Slide Clip................................................................. 3.3
Bottom Connection
Track Anchored to Concrete ................................................. 4.1
Expansion Joints
Brick or CMU Veneer Joint.................................................... 5.1
CEMP-E TI 809-07
30 November 1998
G-2
Figure G-1. Wire Anchors
CEMP-E TI 809-07
30 November 1998
G-3
Figure G-2. Wire Anchor, Details
CEMP-E TI 809-07
30 November 1998
G-4
Figure G-3. Wire Anchor with Continuous Brick Joint Reinforcement
CEMP-E TI 809-07
30 November 1998
G-5
Figure G-4. Pintle Anchor
CEMP-E TI 809-07
30 November 1998
G-6
Figure G-5. Typical Brick Veneer and Steel Stud Panel Wall
CEMP-E TI 809-07
30 November 1998
G-7
Figure G-6. Adjustable Wall Anchor Detail
CEMP-E TI 809-07
30 November 1998
G-8
Figure G-7. Masonry Veneer Steel Stud Panel Wall, Plan View
CEMP-E TI 809-07
30 November 1998
G-9
Figure G-8. Masonry Veneer Steel Stud Panel Wall, Foundation Wall Section
CEMP-E TI 809-07
30 November 1998
G-10
Figure G-9. Masonry Veneer Steel Stud Panel Wall, Structural Steel Section
CEMP-E TI 809-07
30 November 1998
G-11
Figure G-10. Masonry Veneer Steel Stud Panel Wall, Reinforced Concrete Section
CEMP-E TI 809-07
30 November 1998
G-12
Figure G-11. Masonry Veneer Steel Stud Panel Wall, Steel Joist Section
CEMP-E TI 809-07
30 November 1998
G-13
Figure G-12. Slip Joint Details, Typical Single Track
CEMP-E TI 809-07
30 November 1998
G-14
Figure G-13. Slip Joint Details, Typical Double Track
CEMP-E TI 809-07
30 November 1998
G-15
Figure G-14. Slip Joint Details, Parapet Slide Clip
CEMP-E TI 809-07
30 November 1998
G-16
Figure G-15. Bottom Connection, Track Anchored to Concrete
CEMP-E TI 809-07
30 November 1998
G-17
Figure G-16. Expansion Joints, Brick or CMU Veneer Joint
CEMP-E TI 809-07
30 November 1998
H-1
APPENDIX H
Metric Conversion Data Sheet
Quantity Unit Symbol Prefix Symbol Order of Magnitude
length meter m mega M 10
6
mass kilogram kg kilo k 10
3
time second s milli m 10
-3
force newton N= kg m/s
2
stress pascal Pa= N/m
2
energy joule J= N-m
METRIC CONVERSIONS
Multiply by to obtain
AREA AND VOLUME
ft
2
0.092 903 m
2
ft
3
0.028 136 847 m
3
gal 0.003 785 412 m
3
in
2
645.160 000 mm
2
SECTION MODULUS
in
3
16 387.064 mm
3
MOMENT OF INERTIA
in
4
416 231.430 mm
4
LENGTH
foot (ft) 304.800 millimeters (mm)
inch (in) 25.400 millimeters (mm)
MASS
kg (force/mass) 9.806 650 N
pound-mass (lbm) 0.453 592 kilogram (kg, mass)
FORCE
pound-force (lbf) 4.448 222 N
plf 14.593 903 N/m
TORQUE
lb-in 0.112 985 N-m
lb-ft 1.355 818 N-m
Multiply by to obtain
PRESSURE AND DENSITY
foot of water 2.988 980 kPa
g/cm
3
62.427 900 pcf
g/cm
3
9.806 650 kN/m
3
kg/cm
2
98.066 500 kPa
ksi 6.894 757 MPa, N/mm
2
pcf 16.018 460 kg/m
3
pcf 157.087 616 N/m
3
psf 47.880 260 Pa
psi 6.894 757 kPa
CEMP-E TI 809-07
30 November 1998
APPENDIX I
STANDARD DRAWINGS COLD-FORMED STEEL
This Appendix links designers to a standard CADD library of Cold-Formed Steel details in
Intergraph format that are for general information only. These details are available to designers
for use in Military design projects. They were developed originally by AISI for residential
construction and should be modified according for larger projects. They include typical; floor,
roof, and wall framing, plans and elevations. Also included are typical roof truss elevations, and
connection details for floors, walls, openings, and roofs. Connection details can be fastened
using bolts welds, or screws. Punch-outs are not shown but are acceptable and vary in size and
configuration based on the manufacturer. Additional design and detailing is required before this
information can be used in construction documents. Neither the Corps of Engineers nor AISI is
responsible for the proper use of this information. Before specifying or using cold-formed material
a competent Structural engineer shall design and check the adequacy of the design and any cold-
formed component used in the design. Anyone using this information assumes all liability arising
from such use.
Details for moisture protection, thermal insulation, seismic conditions, and high wind conditions
are special requirements that need to be considered in any design using cold-formed steel.
Designers shall use the information from Chapter 4 and Appendix G when designing for moisture
protection and thermal insulation of steel stud systems.
Standard Detail Drawings for Cold-formed Steel Systems:
Stls 101.pdf: Schematic
Stls 102.pdf: Exterior Walls
Stls 103.pdf: Exterior Walls
Stls 104.pdf: Interior Framing Detail
Stls 105.pdf: Roof Member Connections
Stls 106.pdf: Framing Details for Floor and Wall Openings
Stls 107.pdf: Special Reinforcement Bridging, Blocking, & Miscellaneous
Stls 108.pdf: Special Reinforcement Bridging, Blocking, & Miscellaneous
Stls 109.pdf: Special Reinforcement Bridging, Blocking, & Miscellaneous