Professional Documents
Culture Documents
Blood Cold Chain
Blood Cold Chain
Department of Blood Safety and Clinical Technology World Health Organization Geneva
Department of Blood Safety and Clinical Technology World Health Organization Geneva
WHO Library Cataloguing-in-Publication Data World Health Organization The blood cold chain : guide to the selection and procurement of equipment and accessories. 1.Blood preservation instrumentation 2.Plasma 3.Blood platelets 4.Refrigeration methods 5.Equipment and supplies standards 6.Guidelines I.Title ISBN 92 4 154579 8 (NLM classification: WH 460)
Acknowledgements
The Department of Blood Safety and Clinical Technology acknowledges the continued support of the Government of Luxembourg towards the WHO Blood Cold Chain Project, and to the production of these guidelines. The support of the WHO Department of Vaccines and Biologicals and the WHO Procurement Services are also gratefully acknowledged. This publication was prepared under the direction of Mr David Mvere, WHO Consultant, and edited by Ms Kay Bond, BCT/WHO.
Printed: November 2002 Copies may be requested from: Department of Blood Safety and Clinical Technology World Health Organization 1211 Geneva 27, Switzerland Fax: +41 22 791 4836 E-mail: [email protected] www.who.int/bct/ Information on procuring medical equipment may be obtained from: Department of Procurement Services World Health Organization 1211 Geneva 27, Switzerland E-mail: [email protected]
World Health Organization 2002 All rights reserved. Publications of the World Health Organization can be obtained from Marketing and Dissemination, World Health Organization, 20 Avenue Appia, 1211 Geneva 27, Switzerland (tel: +41 22 791 2476; fax: +41 22 791 4857; e-mail: [email protected]). Requests for permission to reproduce or translate WHO publications whether for sale or for noncommercial distribution should be addressed to Publications, at the above address (fax: +41 22 791 4806; e-mail: [email protected]). The mention of specific companies or their products does not imply that they are endorsed or recommended by the World Health Organization in preference to others of a similar nature that are not mentioned. Errors and omissions excepted, the names of proprietary products are distinguished by initial capital letters. The World Health Organization does not warrant that the information contained in this publication is complete and correct and shall not be liable for any damages incurred as a result of its use. The mention of specific companies or of certain manufacturers products does not imply that they are endorsed or recommended by the World Health Organization in preference to others of a similar nature that are not mentioned. Errors and omissions excepted, the names of proprietary products are distinguished by initial capital letters. Designed by minimum graphics Printed in France
Contents
Important note to readers List of products featured in this guide Abbreviations Glossary Preface Chapter 1. Introduction to the WHO Blood Cold Chain Project 1.1 The global challenge 1.2 Objectives of the WHO Blood Cold Chain Project Chapter 2. The blood cold chain process 2.1 WHO definition of blood components 2.2 The national blood cold chain 2.3 The blood cold chain as a work process 2.4 Blood cold chain personnel 2.5 Summary Chapter 3. Blood bank refrigerators 3.1 Overview 3.2 Standard electric blood bank refrigerator Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO 3.3 Solar powered blood bank refrigerators Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO 3.4 Ice lined blood bank refrigerators Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO Chapter 4. Plasma freezers Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO Chapter 5. Platelet agitators Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO
v vi vii viii ix 1 1 2 5 5 5 6 6 8 10 10 10 10 11 11 15 15 16 16 17 17 18 18 20 20 20 21 23 23 23 24
iii
Chapter 6. Plasma Thawing Equipment Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO Chapter 7. Blood Transport Boxes and Coolants Description, functions and limitations of the equipment WHO minimum performance specifications Product information on equipment evaluated by WHO Chapter 8. Temperature monitoring devices 8.1 Overview 8.2 Electronic versions of temperature monitoring devices 8.3 Portable digital thermometers 8.4 Temperature data loggers 8.5 Blood time temperature indicators Product information on equipment evaluated by WHO Chapter 9. Accessories to the blood cold chain equipment 9.1 Voltage regulators 9.2 Standby generators 9.3 Blood and plasma trays or pack holders Product information on equipment evaluated by WHO Chapter 10. Equipment maintenance 10.1 Preventive maintenance 10.2 Management of repairs 10.3 Procuring essential spares for repairs and preventive maintenance 10.4 Common problems in managing an inventory of spare parts Chapter 11. Selecting and procuring blood cold chain equipment 11.1 Selecting manufacturers 11.2 Preparing tendering specifications 11.3 Factors to consider in selecting blood cold chain equipment 11.4 Donated equipment 11.5 Quantity 11.6 Methods of payment 11.7 Checklists 11.8 Purchasing equipment Annex 1: Self Assessment Questionnaire on the Status of the Blood Cold Chain Annex 2: Chlorofluorocarbons (CFC) in Blood Cold Chain Equipment Annex 3: Description of codes used on page vi
26 26 26 27 30 30 31 31 35 35 35 35 35 36 37 41 41 41 43 44 45 45 45 46 46 48 48 49 49 50 52 53 54 55 57 59 61
iv
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
major objective of the WHO Department of Blood Safety and Clinical Technology (BCT) is to assist every Member State to ensure a safe and adequate blood supply that meets national needs at reasonable cost. Many countries face challenges in reaching this goal. These include limited resources and information, a lack of national policy and plans, transfusion transmissible infections such as the human immunodeficiency virus (HIV), and appropriate technology. Access to, and use of appropriate technology are essential for the safe storage and transportation of blood from donation to transfusion, a process referred to as the blood cold chain. The WHO Blood Cold Chain Project is meeting this challenge by providing appropriate technical and logistics information that will empower managers of health care programmes to improve management of the blood cold chain. This publication
provides specific guidance in the selection and procurement of blood cold chain equipment and accessories. As mentioned in the copyright notice, WHO does not endorse or recommend manufacturers or their products listed in this publication over those not mentioned.The products featured are those that (i) were submitted by manufacturers that wished to participate in a WHO project to develop minimum performance specifications for all essential equipment and accessories needed for an effective blood cold chain; and that (ii) met the WHO minimum performance specifications after laboratory testing and field evaluation. The WHO Office of Procurement Services ([email protected]) can be consulted to provide up-to-date information on the procurement of medical equipment and supplies.
Equipment and Model Blood Refrigerators Standard Electric: BR320+ BB510+ BB710+ BBR 25SI-2A CT1-2A Solar Powered VC65F MB50DC+ Ice-lined MB50AC+ MRB 2000+ Plasma Freezers FR160+ CTF406-2A Platelet Agitators PFS42 Agitator in PC900 Incubator Flatbed Platelet Agitators PFS15 PFS42 PFS84 PFS396 Plasma Thawers CytothermDR CytothermD4+ Cytotherm4T+ DH8 Blood Transport Boxes MT25E/CF (blue) 3504/38/CF 55-CF MT12E/CF ICBB-13F CB/20/-CF Temperature Monitoring Devices T615 Recording thermometer AR10-GT-S Recording thermometer Tiny TTM Type G IP68 data logger Tiny TTM Type G data logger Autolog 2000TM data logger Thermo-tracer, data logger 80-1017 3M BTTI Accessories FF500/4R voltage regulator for refrigerators
Code1
Manufacturer
Page
BR/01/2a BR/02/2a BR/03/2a BR/04/4a BR/05/2a BR/06/1b BR/07/1b BR/08/1c BR/09/1c PF/01/3 PF/02/2 PA/01/i
Dometic, Luxembourg Huurre of Finland Huurre of Finland Jewett Refrigeration, USA Jewett Refrigeration, USA Dulas Ltd., UK Dometic, Luxembourg Dometic, Luxembourg Dometic, Luxembourg Dometic, Luxembourg Jewett Refrigeration, USA Helmer, USA Helmer, USA Helmer, USA Helmer, USA Helmer, USA Helmer, USA Phototherm, USA Phototherm, USA Phototherm, USA Helmer, USA Dometic, Luxembourg Thermos, USA Blow Kings, India Dometic, Luxembourg Apex Continental Ltd, India Blow Kings, India Pacific Transducer Co., USA Hyoda Instuments Co., Japan Remonsys Ltd., UK Remonsys Ltd., UK Remonsys Ltd., UK Ocea Soft, France 3M/Berlinger & Co. AG, CH Advance Galatrek, UK
11 12 13 13 14 16 17 18 19 21 22 24 24 25 25 25 25 27 27 28 29 31 32 32 33 33 34 37 37 38 38 39 39 40 44
PA/02/f PA/03/f PA/04/f PA/05/f PT/01/ PT/02/ PT/03/ PT/04/ BB/01/4 (PIS B4/05M) BB/02/1 (PIS B4/18M) BB/03/2 (PIS B4/57M) BB/04/3 (PIS B4/62M) BB/05/3 (PIS B4/72M) BB/06/3 (PIS B4/76M) TD/01 (PIS E6/09) TD/02 (PIS E6/28) TD/03 (PIS E6/43) TD/04 (PIS E6/44) TD/05 (PIS E6/47) TD/06 (PIS E6/48) TD/07 VR/01
* Equipment laboratory tested and evaluated in the field (+indicates that field test results are still awaited). WHO-PIS codes included for ease of reference, where applicable.
1
Codes are: (1) product descrption; (ii) product number; (iii) product capacity, if relevant; (iv) product type, if relevant. Therefore, for example, BR/06/1b means: Blood Refrigerator, WHO/BCT Product No. 06, with a capacity to hold fewer than 50 blood packs, solar powered type product (see Annex 3 for full description).
vi
Abbreviations
not tested Alternate current WHO Blood Cold Chain Project WHO Department of Blood Safety and Clinical Technology Blood Time Temperature Indicator Blood Transfusion Services cubic centimetre Cost of item, insurance and freight to nearest port of destination, excluding customs clearance charges to be borne by buyer. Chlorofluorocarbon, found in some types of refrigerant gases Corrosion Resistance Direct current Deutsche-Industrie-Norm, any of a series of technical standards diameter by length European Norms Ex Works: factory price; everything else to be paid and organized by the buyer Free on Board. Cost of item and delivery cost cleared for export to the sellers freight agent. All other expenses are for the buyer free on truck Hydrochlorofluorocarbon hour(s) hertz (cycles per second)
IEC ISO kg(s) Kwh LED m max. min. mm No. NT PC pk PIS PVC RH RPM SOP TTM V V&B VAC VDC WHO
International Electricity Council International Standards Organization kilogramme(s) Kilowatt-hours Light-emitting diode metre maximum minimum millimetre Number not tested Personal Computer pack Product Information Sheets of WHOS Expanded Programme on Immunization Polyvinyl chloride plastic Relative humidity Revolutions per minute Standard Operating Procedures Time Temperature Monitor volt WHO Department of Vaccines and Biologicals voltage alternating current voltage direct current World Health Organization
kV(A) kilovolts
lts or l litres
dB(A) decibels
vii
Glossary
Cold life of a blood transport box: the amount of time from loading a box with frozen ice packs until the warmest internal temperature reaches +10 C, given a constant external temperature of +43 C. The door to the unit is kept closed. Compressor starting test: to assess the minimum voltage required for a compressor to start. Cooling down time: the time taken by the equipment to cool down effectively a full load of blood or plasma to acceptable temperature limits (see relevant WHO minimum performance specifications). This is important to know, since the faster the equipment is able to cool a load down, the faster the products reach a safe storage temperature. If the cooling down time is too long, it may be necessary to reduce the load by half or a quarter. De-rating: a generators performance is affected by different altitudes. There is a formula for correcting the performance rating of the generator according to the altitude of where it will be located (formula: 1% of its capacity for every 100 m above sea level, 1% for every 5.5 above 20 C.) This is referred to as de-rating of the generator. It is necessary to do this to ensure the correct size of the generator purchased. Door opening test: to assess the effect of continual opening of the door of the refrigerator or freezer on the stable running temperature.
Down time: the time between breakdown of a machine and its repair. Electrical safety rating: to assess against internationally accepted standards the safety of the equipment when exposed to electrical shock. Energy consumption: unlsess otherwise stated, this is measured at full load. Hold-over time: the length of time that the equipment can maintain the temperature of blood or plasma within acceptable limits (see WHO minimum performance specifications) when the energy supply for the equipment is interrupted for whatever reason, e.g. through a power failure. Incoterms: the International Chamber of Commerce official rules for the interpretation of delivery terms. Plasma pack puncturing test: to assess the effectiveness of transport boxes to prevent plasma packs being punctured during a simulated rough ride. Stable running temperature: the stability of the temperature of the equipment within set limits and test conditions. Temperature: all temperatures are plus (+) unless otherwise indicated. Voltage fluctuation test: to assess the stability of the electronic temperature control devices when exposed to voltage fluctuations.
viii
Preface
his is the first WHO publication dedicated to assisting managers of blood programmes to select and procure equipment and devices for the blood cold chain. The safe storage and transportation of blood and blood products is an integral component of the WHO strategy for blood safety. It is estimated that approximately 2% of blood that has been found safe to transfuse may be discarded for various reasons. This percentage varies depending on the management of the inventory and the effectiveness of the blood cold chain, and is a waste of a scarce and valuable resource. WHO recognizes that there are differences in the handling of blood and vaccines in the field. These differences required the development of a blood cold chain that would follow the same principles as the vaccine cold chain, but be specific to blood and blood products. The temperature and volume of blood during storage, the short life span of blood components and their movement to and from the blood bank invariably require equipment with different specifications. The blood cold chain has therefore developed in parallel, and at a different pace to the vaccine cold chain. This publication aims to provide not only WHO minimum performance specifications and product information on equipment evaluated by WHO, but also basic information on the blood cold chain and guidelines on its management. A chapter on equipment maintenance has been especially included following recognition of the lack of knowledge on preventive
maintenance and management of the inventory of spare parts in many countries. Manufacturing prices and exchange rates are not provided since these may well be out-of-date before the Guide is printed. In carrying out its work, the WHO Blood Cold Chain Project has been supported by manufacturers of blood cold chain equipment and national authorities who have participated in field evaluation programmes. Manufacturers equipment, evaluated under the WHO Project, appear in this Guide as examples of blood cold chain equipment only. It is hoped that the data obtained from the equipment evaluated and the minimum performance specifications identified will enable other manufacturers to promote equipment that meets or surpasses these specifications for blood storage and transportation. Future editions of this Guide may include such equipment, in collaboration with the manufacturers and subject to the rights of WHO. Furthermore, it is hoped that this Guide will assist managers and users of blood cold chain equipment to evaluate blood cold chain equipment in general. A cost-effective blood cold chain programme can only be achieved if technologically appropriate equipment for the storage of blood and blood components is affordable and accessible at all levels of the health care system. We hope you will find this Guide useful, and welcome your comments to enhance future editions of this work. Dr Jean C. Emmanuel Director Blood Safety and Clinical Technology
ix
Blood transfusion is an essential part of modern health care. Used correctly, it can save life and improve health. However, as with any therapeutic intervention, it may result in acute or delayed complications and carries the risk of transmission of infectious agents, such as the human immunodeficiency virus (HIV), hepatitis viruses, syphilis and Chagas disease.Yet transfusion-transmissible infections are only one cause of unsafe blood and blood products. Safe and effective transfusion requires the implementation of the following integrated strategy for blood safety. The establishment of a well-organized, nationally coordinated blood transfusion service with quality systems in all areas. The collection of blood only from voluntary, nonremunerated donors from low-risk populations. Testing of all donated blood, including screening for transfusion-transmissible infection; blood grouping and compatibility testing. A reduction in unnecessary transfusions through the effective clinical use of blood and blood products, including the use of simple alternatives to transfusion wherever possible. The safe storage and transportation of blood and blood products is an integral component of the WHO strategy for blood safety. A hiatus in any one of these strategies can compromise the safety of blood. This publication focuses on the adequate storage and transportation of blood components, and provides specific guidance for health care personnel on the selection, procurement and maintenance of related equipment and technology needed from donation to transfusion, a process referred to as the blood cold chain.
CHAPTER 1
and human resources for the maintenance of the equipment are not available or formalized, and this is further aggravated by a frequent lack of spare parts. The transportation of blood between and within blood banks and hospitals is often dependent on the availability of cooler boxes able to maintain temperature over long distances and in relatively high ambient temperatures. Blood is often wasted through the use of domestic type (picnic) cooler boxes or other containers that cannot be relied upon to maintain temperature correctly. The absence of safe blood transport boxes therefore affects the movement of blood and compromises management of the national blood inventory. The conventional thermometer remains the item in most common use for monitoring the temperature of blood in storage equipment in developing countries. This is not adequate as the monitoring of the temperature depends on the user, who cannot monitor the blood constantly, especially outside working hours, and may forget. The use of thermographs and audiovisual alarm systems are uncommon, especially with domestic type equipment.
A cost-effective blood cold chain programme can only be achieved if technologically appropriate equipment for the storage of blood components is affordable and accessible at all levels of the health care system.
It is generally accepted that approximately 2% of blood that has been found safe to transfuse may be discarded. The use of suitable equipment and good management of the blood cold chain are important means of minimizing losses of donated blood.The wider availability and correct use of affordable equipment that meets defined specifications, and is appropriate for the environment in which it will be located, will enable an effective blood cold chain to be established and make a significant contribution to blood safety. The WHO Blood Cold Chain Project is meeting this challenge by providing technical information based on the testing of equipment that will empower those responsible for health care programmes to manage the blood cold chain. A cost-effective blood cold chain programme can only be achieved if technologically appropriate equipment for the storage of blood components is affordable and accessible at all levels of the health care system. The equipment must meet international standards, together with WHO minimum performance specifications and be correctly used and maintained by all personnel involved.
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
such as lightning. The performance of the equipment, e.g. a compressor, at low or high input voltage needs to be assessed. Similarly the stability of sensitive electronic equipment, such as temperature monitoring devices when voltage fluctuates, should also be assessed. v. Any equipment that stores blood components should contain a temperature monitoring device, notably alarm systems that can tell whether the temperature is outside the maximum or minimum range. Furthermore, in order to comply with quality standards, a continuous record of the temperature of the contents of the equipment should be kept. The existence and performance of these devices are critical during the evaluation of the equipment. vi. WHO minimum performance specifications. In addition to the above information, it is important to identify the internationally approved standard with which the equipment complies, e.g. ISO, DIN, EN or IEC.
Field evaluation
The field evaluation studies on the blood cold chain equipment highlighted the following gaps in the blood cold chain: i. Lack of skills in preventive maintenance. ii. Limited knowledge by personnel responsible for blood programmes regarding the management of the blood cold chain. iii. Numerous pieces of equipment lying idle because of the shortage of spare parts or lack of skills to repair them. iv. The need for WHO minimum specifications for blood cold chain equipment such as platelet agitators, plasma thawing equipment, etc. v. The critical need for an indicator that shows the safe storage history of an individual blood component in all situations.
Pilot study
A pilot study on the status of the national blood cold chain was conducted in 27 countries in May 2001. Although this was a limited and qualitative study, it revealed other dimensions to the blood cold chain, notably: i. In the majority of developing countries the blood cold chain is not nationally coordinated and this has a negative impact on the organization of the
preventive maintenance and repair of blood cold chain equipment. ii. Temperature monitoring devices are not routinely used in the domestic equipment still in regular use in the blood banks, nor in domestic (picnic) type of boxes used for blood transportation. iii. Information on the recommendation that all cold chain equipment should use CFC-free refrigerant gas by 2005 is not widely known.1 iv. There is a need for information materials on the management and use of equipment, minimum performance specifications and reference standards in order for managers to select and procure appropriate equipment for the blood cold chain.
One module, User Manual for the Blood Cold Chain, is in preparation for laboratory technical staff in blood transfusion centres and hospital blood banks who are responsible for the installation, monitoring and routine maintenance of blood cold chain equipment. It will focus particularly on the training needs of staff in small blood banks where responsibility for the monitoring and maintenance of blood cold chain equipment rests with employees who are unlikely to have been trained in basic refrigeration mechanics. WHO is also developing a country model for the preventive maintenance, repair and management of spare parts for blood cold chain equipment. Since a successful blood cold chain depends on the efforts of health authorities to promote safe national blood programmes, BCT is addressing quality management at all levels of the blood transfusion programme at international, regional and country level. To this end, a questionnaire has been included in this Guide as an instrument to assist national authorities, hospital blood banks, etc., to assess their needs for blood cold chain equipment (see Annex 1).
Outcomes
This information continues to shape the Projects activities. For example, in order to address the problem of preventive maintenance and management of the blood cold chain, BCT is developing learning manuals for use by managers and users of blood cold chain equipment.
See Annex 2 and Montreal Protocol on the use of CFC refrigerants at: www.unep.ch/ozone/pdf/Montreal-Protocol2000.pdf
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
CHAPTER 2
Red Cells Platelets Plasma Direct clinical use (Fresh frozen plasma) (Cryoprecipitate)
The blood collected and screened as safe for transfusion may be moved from a central to a regional blood bank or district hospital, depending on the structure of the national blood programme. Small or remote hospitals may independently Plasma donor collect and store their own blood. However, this is often not as cost-effective as centralized Plasmapheresis processing, testing and distribution from selected regional centres. Blood may sometimes Plasma derivatives be moved from regional centres to a central hospital, which is Immunoglobulins unable to meet the demand from Albumin within the urban population it Coagulation factors serves.
Viral inactivated plasma
Ministry of Health
procedures all work together to produce an end result: safe and useable blood and blood components. There are three main activities involved in the blood cold chain process: Storage : which keeps blood at the correct temperature from the time it is collected up to the time it is transfused. Packing and transportation: which includes equipment and materials needed to move blood components safely through the blood cold chain. Maintenance of equipment: which provides the proper management, infrastructure and backup needed to ensure a reliable, sustainable and safe blood supply.
Annex 1) in order that appropriate equipment and personnel are put in place. It is the responsibility of the managers at each level of the blood cold chain to identify the key components from collection to transfusion in a given district, province or country. Users of cold chain equipment need to be trained according to an agreed national programme in order to ensure uniformity of practice. Reporting on the performance of cold chain equipment needs to be standardized, as do preventive maintenance schedules in order to reduce down time on the equipment. It is the responsibility of the users to ensure that reports on the performance of the equipment are submitted to management regularly. Figure 2 shows a schematic diagram of the possible structures of a national blood programme. It also shows the line of supply of blood, i.e. of a model blood cold chain.
Tables 13 illustrate the interconnections within each of the three main activities. An understanding of the different elements involved will assist in the evaluation of the current status of the blood cold chain and the implementation of any changes that are necessary.
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Equipment
Personnel Environment Measurements (What data will help keep this process working well?)
Table 2. Packing and transport conditions for blood and blood components
Process components Input (What goes in) Information Materials Elements (What makes the process work) Methods Example Type and quantity of blood components to pack; length of travel Blood components, ice, ice packs, wrapping materials, coolant pouches Standard Operating Procedures for: Packing/transport of red blood cells Packing/transport of platelets Packing/transport of plasma and cryoprecipitate Reception of blood products in the hospital Transportation of blood/blood components within hospital Reception of unprocessed blood from blood mobiles Release of blood and blood components Transport boxes, ice machine, time/temperature indicators Identify who is responsible for packing and transport: blood bank technicians, nurses, drivers, etc. Clean, open spaces and bench space Indicators for process control: Temperature at time of reception Returned products (unsuitable transport conditions) Periodic quality control of transported products, e.g. Platelet pH
Equipment Personnel Environment Measurements (What data will help keep this process working well?)
Equipment Personnel
Environment Measurements (What data will help keep this process working well?)
Donor Clinic Assistants (donor attendants, drivers, donor clerks): Packing of donated blood Monitoring temperature during transport (on long distances) Delivering blood to the blood bank at the required temperatures and within the specified time. Laboratory technical staff: Receiving donated blood Storing blood components according to the Standard Operating Procedures (SOPs) Monitoring temperature of stored products Packing blood and blood components according to length and time of travel Quality control of blood cold chain equipment and products Reception and installation of blood cold chain equipment Verifying the operation of new or repaired blood cold chain equipment.
Hospital clinic staff: Reception of blood and blood components from the blood bank Monitoring temperature of stored blood components at the blood bank or at the wards Operate blood warmers Ensure safe transfusion of blood and blood components. It is essential that all managers and users of blood cold chain equipment are trained in their correct maintenance and use.
2.5 Summary
Many elements play an important role in ensuring the safe storage and transportation of blood from its donation to transfusion. The elements of the blood cold chain are: Blood cold chain equipment, for storage and for transportation Temperature monitoring devices
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Back-up systems Well trained personnel Standard Operating Procedures that guide the user on how to perform each of the activities involved in storing, transporting and packing blood products Measurements that will help to monitor and maintain our control processes.
These elements form the basis of three main working processes: storage, transportation and maintenance of the blood cold chain. Yet it is a very fragile chain: one weak link can have very serious, even fatal, consequences for a patient. The national blood cold chain must therefore involve all levels of the health care system from the small district hospital up to the Ministry of Health.
CHAPTER 3
3.1 Overview
The blood storage refrigerator is the basic requirement for any blood bank. Unlike domestic types of refrigerators, blood bank refrigerators have the following key design features: Heavier insulation all round to enable a longer holdover time in the event of power failure and ability to maintain temperatures between +2 and +6 C. A cooling fan to enable even distribution of air in the cabinet. Temperature monitoring devices, comprising an external temperature display facility and an alarm system for abnormal temperature or power failure, etc. Scratch resistant internal lining of the cabinet (stainless steel or aluminium). Glass front door or other design to enable the user to view the contents in the cabinet without affecting the temperature, and roll out drawers or shelves for holding the blood. Some equipment may be fitted with two compressors. Although only one compressor works at any one time, this design reduces down time due to compressor failure. The compression type of blood bank refrigerator is therefore the only type recommended for blood storage and the only type described in this Guide. While the domestic type of electric compression refrigerator may be locally made and therefore readily available and supported by industry, its design is not suitable for blood storage, principally because: it is usually poorly insulated and not designed to maintain the temperatures recommended; it warms up quickly when electricity fails; it may not operate in high ambient temperatures (+43 C); temperatures often fall below freezing in areas close
1
to the freezing compartment, especially in models without sufficient insulation of the refrigerating compartment; the doors are poorly insulated; and temperature monitoring devices are not routinely fitted.
Generally whole blood is loaded into a refrigerator at room temperature. The bigger the total volume, the longer it will take to cool the blood to the acceptable temperature of storage of +4 C. Sub-divided into smaller volumes, the blood will cool faster, but this will require more storage space for the same total given load of blood.
While the domestic type of electric compression refrigerator may be locally made ... its design is not suitable for blood storage
Chapter 11 shows a chart which assists managers to select the best compression type of blood bank refrigerators. Wherever there is a need for more than 8 hours of electricity per 24 hours, the compression type of refrigerator is the preferred choice. In addition to the standard electric refrigerator, the different types of ice-lined and solar powered compression type blood bank refrigerators are described below.
This equipment is the preferred choice in many laboratories assured of a electricity supply 24 hrs/day from the national electricity grid. The equipment is also connected to a standby electricity generator, e.g. of the hospital or blood bank in case of a failure of the mains power supply. Manufacturers provide different sizes to suit various needs (see also Chapter 9). The key limitations for optimal performance are the hold-over time during power failure in the absence of a standby generator and also the cooling down time.
10
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
PRODUCT INFORMATION ON EQUIPMENT EVALUATED BY WHO STANDARD ELECTRIC BLOOD BANK REFRIGERATORS
s MODEL NO. BR 320 s CODE: BR/01/2A s COMPANY NAME AND ADDRESS: Dometic (ex Electrolux ) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.lu s FEATURES Type of internal lining of the cabinet: Stainless steel Description of shelves and drawers: Grids or drawers Doors: Plain door or door with glass Internal air cooling mechanism: Forced air Internal lighting: Yes Temperature indicator and alarm system: Yes Thermographs: Yes Interface for Remote Temperature Monitoring: RS 485 s SPECIFICATIONS Internal capacity (litres): 319 net volume Maximum no. of blood or plasma packs loaded: 240 pks External dimensions in cm (H x W x L): 174 x 85 x 79 Gross volume (litres): 408 Weight (kg): 179 s PERFORMANCE DATA
Full load Half load Quarter load
Internal temperature minimum: Internal temperature maximum: Hold-over time: Cool down time: Energy consumption: Kwh/24h not tested
0.5
s ENERGY REQUIREMENTS Energy source: Rated voltage/frequency: 220240 V/50 Hz and 115 V/60Hz Int. standards: EMI 89/336EEC. Low voltage 73/23/EEC and 93/68/EEC code AB1 Minimum compressor starting voltage at 32 C ambient temperature: 158 V Minimum compressor starting voltage at operating temperature: 158 V Shipping volume/gross weight: 1.67m3/214 kg
11
s ENERGY REQUIREMENTS Energy source: AC Electricity Rated voltage/frequency: 230 V/50 Hz International standards equipment complies with: ISO 8187 EN 28187 Mininum compressor starting voltage at 32 C ambient temperature: 154 V Minimum compressor starting voltage at operating temperature: 154 V s ADDITIONAL INFORMATION Shipping volume/gross weight: 1.26m3/160 kg International standards equipment complies with: ISO 8187 EN 28187 s ACCESSORIES Temperature recorder Recorder paper, 100 pks Recorder pen Blood bag baskets (total capacity 15 pks) s RECOMMENDED SPARE PARTS PER 10 UNITS OF EQUIPMENT
Spare part Code Quantity
Door switch Sensor Motorfan On Off key Thermostat Main board Compressor Drier
1 2 1 1 1 1 1 1
s MODEL NO. BB 510 s CODE: BR/02/2A s COMPANY NAME AND ADDRESS Huurre Group Oy P.O. Box 127 33101 Tampere Finland Tel +358 20 55 55 11 Fax +358 20 55 55 288 E-mail [email protected] www.huurre.com s FEATURES Type of internal lining of the cabinet: Stainless steel Description of shelves and drawers: 5 stainless steel drawers Doors: Solid outer door plus perspex inner door. Lockable Internal air cooling mechanism: Fan air cooling. Automatic defrosting Internal lighting: Interior light 1 x 36 W Temperature indicator and alarm system: Digital display to 1 C. Mains power failure alarm. High/low temperature audible and visual alarms. Battery back-up Thermographs: See accessories Interface for Remote Temperature Monitoring: Yes s SPECIFICATIONS Internal capacity (litres): 315 Maximum no. of blood or plasma packs loaded: 60 x 450 ml blood bags External dimensions in cm (H x W x L): 205 x 60 x 70 Gross volume (litres): 380 Weight (kg): 140 kg s PERFORMANCE DATA
Full load Half load Quarter load
Compressor Evaporator Evaporator fan motor Condenser fan motor Filter drier Condensate heater Service valve Control unit Transformer Thermostat Lamp Contactor Relay Relay base Door switch Door gasket
1501950 1801020 2501283 2501283 3853070 5502150 7608558 5201350 5201300 4001410 7700058 6401000 8705006 8705007 6501540 5002113
2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 2 pks 1 pk 1 pk 2 pks 2 pks
Internal temperature minimum: 3.1 C Internal temperature maximum: 5.3 C Hold-over time: 30 min Cool down time: 5.5 hrs Energy consumption: 9.86 Kwh/24h
29 min
12
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
s ADDITIONAL INFORMATION Equipped with dual refrigeration system International standards equipment complies with: ISO 8187 EN 28187 Shipping volume/gross weight: 1.71m3/210 kg s ACCESSORIES Temperature recorder Recorder paper, 100 pks Recorder pen Blood bag baskets (total capacity 20 pks) s RECOMMENDED SPARE PARTS PER 10 UNITS OF EQUIPMENT
Spare part Code Quantity
s MODEL NO. BB 710 s CODE: BR/03/2A s COMPANY NAME AND ADDRESS Huurre Group Oy P.O. Box 127 33101 Tampere Finland Tel +358 20 55 55 11 Fax +358 20 55 55 288 E-mail [email protected] www.huurre.com s FEATURES Type of internal lining of the cabinet: Stainless steel Description of shelves and drawers: 5 stainless steel drawers Doors: Solid outer door plus perspex inner door. Lockable Internal air cooling mechanism: Fan air cooling. Automatic defrosting Internal lighting: Interior light 2 x 36 W Temperature indicator and alarm system: Digital display to 1 C. Mains power failure alarm. High/low temperature audible and visual alarms. Battery back-up Thermographs: See accessories Interface for Remote Temperature Monitoring: Yes s SPECIFICATIONS Internal capacity (litres): 455 Maximum no. of blood or plasma packs loaded: 90 x 450 ml blood bags External dimensions in cm (H x W x L): 205 x 85 x 70 Gross volume (litres): 580 Weight (kg): 195 kg s PERFORMANCE DATA
Full load Half load Quarter load
Compressor Evaporator coil Evaporator fan motor Condenser fan motor Filter drier Condensate heater Service valve Control unit Transformer Thermostat Lamp Contactor Relay Relay base Door switch Door gasket
1501950 1801062 2501283 2501283 3853070 5502150 7608558 5201350 5201300 4001410 7700058 6401000 8705006 8705007 6501540 5002115
4 pks 2 pks 2 pks 2 pks 4 pks 2 pks 4 pks 2 pks 2 pks 2 pks 4 pks 2 pks 1 pk 1 pk 2 pks 2 pks
Internal temperature minimum: 2.8 C 3.1 C Internal temperature maximum: 5.7 C 5.2 C Hold-over time: 35 min 45 min Cool down time: 13.4 hrs Energy consumption: 10.2 Kwh/24h
38 min
STRAP
s MODEL NO. BBR25SI-2A s CODE: BR/04/4A s COMPANY NAME AND ADDRESS Jewett Refrigeration Inc. 275 Aiken Road Asheville, NC 28804 USA Tel 1 828 658 2845 Fax 1 828 645 9466 www.jewettonline.com s FEATURES Type of internal lining of the cabinet: Stainless steel
s ENERGY REQUIREMENTS Rated voltage/frequency: 230 V/50 Hz Energy source: AC Electricity Min. compressor starting voltage at 32 C ambient temperature: 154 V Minimum compressor starting voltage at operating temperature: 154 V
13
Description of shelves and drawers: 6 stainless steel drawers Doors: Triple pane heated glass with heated frame. Lockable Internal air cooling mechanism: Blower coil. Automatic defrosting Internal lighting: Fluorescent light full height Temperature indicator and alarm system: Digital display to 1 C, door ajar alarm, mains power failure alarm, high/ low temperature audible and visual alarms. Battery back up Thermographs: Model 7ER Interface for Remote Temperature Monitoring: Optional s SPECIFICATIONS Internal capacity (litres): 702 Maximum no. of blood or plasma packs loaded: 360 x 450 ml blood bags External dimensions in cm (H x W x L): 210 x 91 x 74 Gross volume (litres): 760 Weight (kg): 281.5 kg s PERFORMANCE DATA
Full load Quarter load Empty
STRAP
s MODEL NO. CT1-2A s CODE: BR/05/2A s COMPANY NAME AND ADDRESS Jewett Refrigeration Inc. 275 Aiken Road Asheville, NC 28804 USA Tel 1 828 658 2845 Fax 1 828 645 9466 www.jewettonline.com s FEATURES Type of internal lining of the cabinet: Stainless steel Description of shelves and drawers: 3 stainless steel drawers Doors: Lockable Internal air cooling mechanism: Blower coil. Automatic defrosting Internal lighting: No Temperature indicator and alarm system: Digital display to 1 C, mains power failure alarm, high/low temperature audible and visual alarms. Battery back up Thermographs: Optional Interface for Remote Temperature Monitoring: Optional s SPECIFICATIONS Internal capacity (litres): 153 Maximum no. of blood packs loaded: 60 x 450 ml bags External dimensions in cm (H x W x L): 49 x 49 x 55 Gross volume (litres): 0.52m3 Weight (kg): 95 s PERFORMANCE DATA
Full load Quarter load Empty
Internal temperature minimum: Internal temperature maximum: Hold-over time: Cool down time:
s ENERGY REQUIREMENTS Rated voltage/frequency: 230V 50Hz; 115V 60Hz Energy source: AC electricity Min. compressor starting voltage at 32 C ambient temperature: 154V Minimum compressor starting voltage at operating temperature: 154V s ADDITIONAL INFORMATION International standards equipment complies with: AABB, ANRC & PDA Shipping volume/gross weight: 1.94 m3/288 kg
Internal temperature minimum: Internal temperature maximum: Hold-over time:) Cool down time:
s ENERGY REQUIREMENTS Rated voltage/frequency: 230V 50Hz; 115V 60Hz Energy source: AC Electricity Min. compressor starting voltage at 32 C ambient temperature: 76V on 115V@60Hz Minimum compressor starting voltage at operating temperature: 78V on 115V@60Hz s ADDITIONAL INFORMATION International standards equipment complies with: AABB, ANRC and FDA Shipping volume/gross weight: 1.94 m3/288 kg
14
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
In many developing countries blood transfusions may take place in health centres or district hospitals that do not have access to the national electricity grid. In some health facilities the electricity generator for a health centre may only be used after sunset. In these situations blood bank refrigerators need to be able to maintain blood at between +2 to +6 C 24 hrs of the day. In countries with a sufficient quantity of sunshine throughout the year, solar powered refrigerators may be the answer. A flow chart in Chapter 11 provides guidance on where solar refrigeration may be recommended. The design of the cabinet of the compression refrigerator powered by solar energy is different from that of the standard electric refrigerator. The insulation is thicker, there is no fan cooling and only sizes with a maximum of 50 units are consistent with the needs of the smaller hospitals or health centres. The energy requirements are also low. In order to conserve the cold, the equipment is designed as chest type (top opening door) and there is no internal light in the cabinet. The equipment shall have the same temperature monitoring devices as for the standard electric refrigerator. Solar refrigerators and ice pack freezers use CFC-free refrigerant gas and may also have an ice-pack freezer. Recommended power consumption is less than 0.7 Kwh/24 hours for appliances with a gross volume of less than 50 litres, and less than 0.1 Kwh per additional 10 litres gross volume, at 43 C. The temperature of the freezer section of solar powered equipment is typically below -10 C. This is unsuitable for the medium to long term storage of fresh frozen plasma. The key features for solar powered equipment are: 1. Photovoltaic array: Modules must meet the latest applicable specifications laid down by the Jet Propulsion Laboratory (USA) or Joint Research Centre, Ispra, (Italy). Array structures are designed to withstand wind loads of +200 kg per square metre and supplied with fixings for either ground or roof mounting. Protection against the effect of lightning is provided for the battery charge regulator and other components. The system is designed to enable continuous operation of the refrigerator and freezer (loaded and including ice pack freezing) during the periods of lowest sunlight in the year. If other loads, such as lighting, are included in the system, they shall operate from a separate battery set, NOT from the battery set that supplies the refrigerator. 2. Array-to-refrigerator cable: This cable is sized so that when the array is at its maximum operating temperature and maximum output, the voltage delivered
is sufficient to charge the batteries at their maximum charge rate. The manufacturer provides recommendations for sizing the cable (as a function of the distance from array to control box). 3. Battery set: Batteries shall be capable of withstanding a minimum of 1000 cycles to 50% discharge. Maintenance intervals shall be limited to a maximum of once every six months. No dry cell batteries shall be used to power instruments or controls. The batteries shall be housed within a lockable ventilated cabinet with access for maintenance inspection in place. Batteries must meet the WHO design specifications.1 Supporting documentation on the batteries must be provided. Batteries must be supplied dry/charged with acid in separate hermetic containers. 4. Battery charge regulator: Battery charge regulators must meet WHO design specifications and supporting documentation must be provided.They must be precisely set to meet the charge and temperature requirements of the selected battery and disconnect the load when the battery has reached a state of charge that can be repeated for a minimum of 1000 cycles. Lightning surge protection shall be provided. The load shall be automatically reconnected when the system voltage recovers. Solar technology is reliable. However, a study of solar powered equipment for vaccine storage conducted by WHO and UNICEF shows among other things that the maintenance and replacement of parts such as batteries and regulators, which become necessary after an average of five years, remains the major problem because these systems are often located in isolated areas and funds are rarely put aside for this purpose.
15
Supplier
In order to ensure a reliable solar system it is most important that solar powered blood bank refrigerators are supplied with the solar system to match the equipment, by a WHO approved supplier. This ensures a reliable system appropriate for the environment and energy demands of the equipment.
Temperature Monitoring: Digital temperature display with 0.1 C graduation Temperature recording device Visual and audible alarm system indicating unsafe temperatures Battery status visual display Temperature recorder facility Facility for remote alarm contact
Instructions/manuals
Manuals shall be provided with each refrigerator with clear descriptions for users and electricians of: simple daily, weekly and monthly maintenance tasks; periodic preventive maintenance checks; diagnostic and repair procedures; temperature adjustments; installation procedures.
PRODUCT INFORMATION ON EQUIPMENT EVALUATED BY WHO SOLAR POWERED BLOOD BANK REFRIGERATORS
s MODEL NO. VC65F s CODE: BR/06/1B s COMPANY NAME AND ADDRESS Dulas Ltd. Dyfi Eco Parc Machynlleth, Powys SY20 8AX United Kingdom Tel: +44 1654 70 50 00 Fax: +44 1654 70 30 00 E-mail: [email protected] Internet: www.dulas.org.uk s FEATURES Type of internal lining of the cabinet: Aluminium ripple finish Description of shelves and drawers: 2 baskets each with 3 shelves Doors: Solid lid Internal air cooling mechanism: Nil Internal lighting: Nil Temperature indicator and alarm system: Digital temperature display at 1 C. Integrated high/low temperature alarm and max/min temperature memory Thermographs: Temperature recorder and charts Interface for Remote Temperature Monitoring: Nil s SPECIFICATIONS Internal capacity (litres): Refrigerator: 24 blood pks Freezer: 16.6L ice packs Maximum no. of blood pks loaded: 24 (450 ml) External dimensions in cm (H x W x L): 97 x 93 x 80 Gross volume (litres): Refrigerator 68 Freezer 25 Weight (kg): 115 kg
* The hold-over time and cool down times were measured at +43 C ambient at full load. This means that the lower the ambient temperature, the better the performance of the equipment.
16
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
s PERFORMANCE DATA
Full load Half load Quarter load
External dimensions in cm (H x W x L): 83 x 82 x 92 Gross volume (litres): 70 Weight (kg): 60 s PERFORMANCE DATA
Full load Half load Quarter load
Internal temperature minimum: 3.8 C Internal temperature maximum: 4.3 C Hold-over time: 2.42 hrs Cool down time: 8.75 hrs Energy consumption: 0.53 Kwh/24h
s ENERGY REQUIREMENTS Rated voltage/frequency: Energy source: 12V DC Nominal Min. compressor starting voltage at 32 C ambient temperature: Minimum compressor starting voltage at operating temperature: s ADDITIONAL INFORMATION Requires solar energy system: This will be supplied according to WHO/UNICEF approved solar refrigerator supplier status for solar vaccine refrigerators. International standards equipment complies with: EU Safety Approval Shipping volume/gross weight: 1.0m3/140 kg
Internal temperature minimum: 4.1 C Internal temperature maximum: 5.0 C Hold-over time: 4.5 hrs Cool down time: 22.3 hrs Energy consumption: 1.14 Kwh/24h
s ENERGY REQUIREMENTS Rated voltage/frequency: 12 or 24 VDC/60Hz Energy source Minimum compressor starting voltage at 32 C ambient temperature: Minimum compressor starting voltage at operating temperature: s ADDITIONAL INFORMATION International standards equipment complies with: code AM1 Shipping volume/gross weight: 0.73m3/78 kg
STRAP
s MODEL NO. MB 50DC/CF 991.2340.01 s CODE: BR/07/1B s COMPANY NAME AND ADDRESS Dometic (ex Electrolux ) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 * Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.lu s FEATURES Type of internal lining of the cabinet: Polyethelene Description of shelves and drawers: 2 wire baskets Doors: Lid Internal air cooling mechanism: Fan Internal lighting: No Temperature indicator and alarm system: Digital display with alarm functions Thermographs: Optional (in the unit) Interface for Remote Temperature Monitoring: No s SPECIFICATIONS Internal capacity (litres): 14.4 Maximum no. of blood packs loaded: 32 x 450 ml blood bags
CHAPTER 3. BLOOD BANK REFRIGERATORS
Compressor BF50F Fan 12 VDC Fan 230 VAC Drier Temperature controller EWPC 901
1 1 1 1 1
Ice-lined refrigerators are especially designed to have a longer hold-over time. This means that, unlike standard electric blood bank refrigerators, they may hold the temperature below +10 C for up to 72 hours following a power cut. This is achieved through lining of the cabinet with water/ice containers or freezer sections with ice packs positioned adjacent to the blood storage area. During periods of power failure and load shedding, the ice packs act as a means of cold storage to protect the units of blood stored in the refrigerator. Ice-lined refrigerators are strongly recommended for blood banks located in areas with unreliable power supply and frequent power cuts, typically in district or regional
17
centres. However, to comply with WHO standards, icelined equipment should be fitted with temperature monitoring devices and alarms systems. The freezer part of the equipment is not recommended for the storage of plasma packs since the temperature of the freezer section of ice-lined equipment does not typically fall below -10 C, which is unsuitable for the medium to long term storage of fresh frozen plasma. The ice packs may also be used in blood transport boxes. In order to freeze the water lining within a limited number of hours when the power is available the compressor has to operate extensively and the storage area in the bottom of the appliance falls below 0 C. Blood bags should, therefore, NOT be stored within 15 cm of the base of these models. Another limitation with this type of equipment is that, although the chest type design ensures low temperature storage by reducing the loss of cold air during opening, access to blood bags at levels below the top shelf requires the entire basket to be removed. This is often cumbersome and can quickly increase the temperature of the cabinet. Protection of the blood bags also needs to be ensured whilst seeking to attain freezing temperatures for the ice-lining.
Internal Temperature Control: Electronic temperature control, range +2 C to +6 C in refrigerator section with setting accuracy of 1C whatever the load. In freezer section, temperature range -20 C to -40 C Fan air cooling External Ambient Temperature: Performs in an ambient temperature of +10 C to +43% Hold-Over Time*: A full load of blood packs at +4 C ( 1 C ) takes at least 1 hr to rise to above +6 C A full load of blood packs at +4 C ( 1 C ) takes at least 2 hrs to rise to above +10 C Cooling Down Time*: A full load of blood packs at +37 C takes a maximum of 8 hrs for all the packs to reach below +6 C Temperature Monitoring: Digital temperature (LED) display with 0.1 C graduation Temperature recording device Visual and audible alarm system indicating unsafe temperatures Battery back up for alarm and temperature recording device Facility for remote alarm contact
s COMPANY NAME AND ADDRESS Dometic (ex Electrolux) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.lu s FEATURES Type of internal lining of the cabinet: Polyethylene Description of shelves and drawers: 2 wire baskets Doors: Lid Internal air cooling mechanism: Fan Internal lighting: No Temperature indicator and alarm system: Digital display with alarm functions Thermographs: Optional (in the unit) Interface for Remote Temperature Monitoring: No s SPECIFICATIONS Internal capacity (litres): 14.4 Maximum no. of blood bags loaded: 32 x 450 ml blood bags
* The hold-over time and cool down times were measured at +43 C ambient at full load. This means that the lower the ambient temperature, the better the performance of the equipment.
18
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
External dimensions in cm (H x W x L): 83 x 82 x 98 Gross volume (litres): 70 Weight (kg): 60 s PERFORMANCE DATA
Full load Half load Quarter load
s FEATURES Type of internal lining of the cabinet: PVC Description of shelves and drawers: 2 wire baskets Doors: Lockable lid Internal air cooling mechanism: Yes Internal lighting: No Temperature indicator and alarm system: Digital display alarm functions Thermographs: No Interface for Remote Temperature Monitoring: No s SPECIFICATIONS Gross internal volume (litres): Refrigerator 76 Freezer 17 Maximum no. of packs loaded: 38 x 450 ml blood bags External dimensions in cm (H x W x L): 85 x 94 x 69 Rated voltage/frequency: 220240 V/5060 Hz Weight (kg): 92 kg s PERFORMANCE DATA
Full load Half load Quarter load
Internal temperature minimum: 3.6 C 3.8 C Internal temperature maximum: 4.5 C 4.8 C Hold-over time: 6.3 hrs 3.5 hrs Cool down time: 37.1 hrs 4/6 Energy consumption: 1.68 Kwh/24hr
2.8 hrs
s ENERGY REQUIREMENTS Rated voltage/frequency: 230 VAC 50/60 Hz Energy source: AC Electricity Minimum compressor starting voltage at 32 C ambient temperature: 132 V Minimum compressor starting voltage at operating temperature: 132 V s RECOMMENDED SPARE PARTS PER 10 UNITS OF EQUIPMENT
Spare part Code Quantity
Internal temperature minimum: 3.2 C 3.8 C Internal temperature maximum: 4.8 C 5.0 C Hold-over time: 10.1 hrs 9.4 hrs Cool down time: 16.1 hrs 7.5 hrs Energy consumption (Kwh/24 hrs): 2.92 2.89
7.8 hrs
Compressor 230 VAC/50Hz Compressor 115 VAC/60Hz Fan 12 VDC Fan 230 VAC Drier Main board
1 1 1 1 1 1
s ENERGY REQUIREMENTS Energy source: AC Electricity Minimum compressor starting voltage at 32 C ambient temperature: 136 V Minimum compressor starting voltage at operating temperature: 132 V s ADDITIONAL INFORMATION International standards equipment complies with: DIN EN 9001: 1994 Shipping volume/gross weight: 1.1m3/86 kg
ADDITIONAL INFORMATION International standards equipment complies with: 73/23/ EEC and 93/68/EEC Shipping volume/gross weight: 0.73m3/78 kg
STRAP
s MODEL NO. MRB2000 920.6811.2 s CODE: BR/09/1C s COMPANY NAME AND ADDRESS Dometic (ex Electrolux) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.lu
Starting device Capacitor for compressor Thermostat internal Compressor Internal fan
3 3 1 1 3
19
Plasma freezers
CHAPTER 4
All freezers described in this Guide are compression type freezers. WHO has evaluated compression-type plasma freezers using CFC-free refrigerant gas and electricity supply from the national grid. A plasma freezer need not be connected to a standby electricity generator because the freezer normally holds temperature below freezing point for more than 24 hrs unless the door is opened frequently. The freezer is especially designed for the storage of plasma. It has an internal fan cooling mechanism to ensure the distribution of air The freezer is evenly throughout the equipment especially designed and temperature monitoring to store plasma. It devices. Ideally, after opening the has an internal fan door, each shelf may be opened separately thus conserving the cooling mechanism temperature. The insulation of the to ensure the equipment is thicker than an distribution of air ordinary domestic freezer and this evenly throughout helps to maintain temperature the equipment and lower than -35 C.
they are usually poorly insulated, especially the doors, and are not designed to maintain the temperatures recommended; they warm up quickly when electricity fails; they may not operate in high ambient temperatures (+43 C); temperature monitoring devices are not routinely fitted. In summary, the storage time for plasma stored in domestic freezers is shorter than in plasma freezers and the quality may be compromised.
Plasma freezers
Specification Reference: BTS/FR.1 Purpose of Equipment: To freeze and store plasma in a blood bank Type of Equipment: Compression freezer with CFC-free refrigerant gas and electricity supply from the national grid Laboratory Test Procedure: Standard Test Procedure: BTS/ Proc/1 Construction: Internal: Stainless steel (min. 22g) External: Corrosion Resistant (CR at least 1mm thickness) CFC-free insulation Design: Chest or Upright Type Door: Solid door Drawers: Roll out type Electrical Characteristics: Input voltage: 220/240V 50HZ or 110V 60HZ AC single phase Equipment meets electrical safety specifications such as that of IEC Minimim Compressor Starting Voltage: 22% below nominal voltage Internal Temperature Control: Electronic temperature control Operating temperature, -35 C to -40 C with setting accuracy of 1 C whatever the load Fan air cooling Automatic defrost within safe temperature range
performance are the cooling or freezing down time. Plasma is generally loaded in a freezer while at room temperature. The bigger the volume loaded the longer it will take to cool the plasma to the acceptable temperature of storage of below -35C. The user may opt to reduce the load in order to achieve safe storage temperatures more quickly. This means more storage space is required for a given load of plasma prepared. While the local domestic freezer is readily available, storage of plasma in domestic freezers is not recommended because: the operating temperature of a domestic freezer does not fall below -20 C; cooling down time for a load of plasma is too long;
1
20
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
External Ambient Temperature: Performs in an ambient temperature of +10 to +43 C Hold-Over Time*: A full load of plasma packs at -36 C takes at least 1 hr to rise to above -20 C A full load of plasma packs at -36 C takes at least 32 hrs to rise to above -5 C Cooling Down Time*: A full load of plasma packs at +25C takes a maximum of 5 hrs for all the packs to reach below -5 C A full load of plasma packs at +25 C takes a maximum of 30 hrs for all the packs to reach below -20 C Temperature Monitoring: Digital temperature (LED) display with 0.1 C graduation Temperature recording device Visual and audible alarm system indicating unsafe temperatures Battery back up for alarm and temperature recording device Facility for remote alarm contact
s PERFORMANCE DATA
Full load Quarter Empty load
Internal temperature minimum: Internal temperature maximum: Hold-over time: Cool down time:
-36.9 C -35.1 C -36.1 C -33.5 C 6.6 4.2 36.5 hrs 18.4 hrs
s ENERGY REQUIREMENTS Rated voltage/frequency: 240V/50Hz 115V/60/Hz Energy source: AC Electricity Minimum compressor starting voltage at 32 C ambient temperature: 175 V Minimum compressor starting voltage at 32 C operating temperature: 175 V s ADDITIONAL INFORMATION
International standards equipment complies with: 73/23/ EEC 93/68/EEC s RECOMMENDED SPARE PARTS PER 10 UNITS OF EQUIPMENT
Spare part Code Quantity
s MODEL NO. FR 160 991.7901.10 s CODE: PF/01/2 s COMPANY NAME AND ADDRESS Dometic (ex Electrolux) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.lu s FEATURES Type of internal lining of the cabinet: V2A-1.4301 Description of shelves and drawers: Grids or drawers Doors: Plain door Internal air cooling mechanism: Forced air Internal lighting: No Temperature indicator and alarm system: Yes Thermographs: Yes Interface for Remote Temperature Monitoring: RS 485 s SPECIFICATIONS Internal capacity (litres): 167 Maximum no. of plasma packs loaded: 90 x 300 ml External dimensions in cm (H x W x L): 131 x 85 x 79 Gross volume (litres): 246 Weight (kg): 149
Compressor Motorfan Drier Gasket door Door switch Sensor On Off key Magnetic valve Main board
1 1 1 1 1 2 1 1 1
* The hold-over time and cool down times were measured at +43 C ambient at full load. This means that the lower the ambient temperature, the better the performance of the equipment.
21
STRAP
s MODEL NO. CTF406-2A* s CODE: PF/02/2 s COMPANY NAME AND ADDRESS Jewett Refrigeration Inc. 275 Aiken Road Asheville, NC 28804 USA Tel 1 828 658 2845 Fax 1 828 645 9466 www.jewettonline.com s FEATURES Type of internal lining of the cabinet: Stainless steel Description of shelves and drawers: 3 stainless steel drawers Doors: Lockable door Internal air cooling mechanism: Blower coil. Automatic defrosting Internal lighting: Not applicable Temperature indicator and alarm system: Digital display to 1 C. Mains power failure alarm, high/low temperature audible and visual alarms. Battery back up Thermographs: Optional Interface for Remote Temperature Monitoring: Optional s SPECIFICATIONS Internal capacity (litres): 153 Maximum no. of plasma pks loaded: 88 x 300 ml External dimensions in cm (H x W x L): 49 x 49 x 55 Gross volume (litres): 0.52 m3 Weight (kg): 95 s PERFORMANCE DATA
Full load Quarter load Empty
Internal temperature minimum: Internal temperature maximum: Hold-over time: Cool down time: Energy consumption:
s ENERGY REQUIREMENTS Energy source: AC Electricity Rated voltage/frequency: 230V 50Hz, 115V 60Hz Minimum compressor starting voltage at 32 C ambient temperature: Minimum compressor starting voltage at operating temperature: s ADDITIONAL INFORMATION International standards equipment complies with: AABB, FDA
22
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Platelet agitators
CHAPTER 5
Key features
The design of the door enables the user to inspect the contents without opening the door. This minimizes temperature changes in the incubator housing the platelet agitator. It is also important for the shelves to be corrosion resistant because of occasional spillage from the pilot tubes of the platelet packs.
Platelet agitators are designed for the storage of platelets at a temperature of between 20 C24 C. Only standard electric models are available. Platelets must be kept agitated if they are to retain their viability and adhesive properties. Only the flatbed type of agitator has been evaluated as it is reported that the agitation achieved is better than that obtained in rotary types of agitators. The platelet agitator may be fitted inside an incubator which maintains the desired temperature, or left as a free standing unit in an air conditioned room set at between 20 C24 C. There are differing sizes and designs. Since the agitation is continuous, the equipment has to be robust and emit low noise. Key performance factors are the degree of amplitude of the agitation and the number of strokes achieved per minute. These two factors measure the extent of the agitation in order to ensure Key performance maximum effect thus allowing free factors are the exchange of gases within and degree of amplitude outside the blood pack.
Platelet agitators
Specification Reference: BTS/PAC/IN.1 Purpose of Equipment: To continuously agitate platelet concentrates in an incubator in an even suspension in a plasma bag Type of Equipment: Flatbed agitator fitted inside a temperature-controlled incubator operating with CFC-free refrigerant gas and insulation material and electricity from the national grid Laboratory Test Procedure: Standard Test Procedure: BTS/ PAC/Proc. 1 Construction: Internal: Stainless steel (min. 304 grade) External: Corrosion Resistant, at least 1mm thickness Designed to hold a load of random platelet packs (300ml bag size) or apheresis platelet packs (500 x 1 litre) or a mixture of both types. Doors enable inspection of contents without opening the door Design of Shelves: Shelves are made of corrosion resistant material with sufficient clearance to minimize noise Easy loading and withdrawal of platelet packs. Shelves cannot be pulled out in error The agitator holding the shelves is suspended in such a way as to ensure minimum noise for the life of the agitator Electrical Characteristics: Nominal input voltage: 220/240V 50Hz or 110V 60Hz Equipment meets electrical safety specifications such as that of the IEC Internal Temperature Control: Fan cooling. Electronic temperature control to maintain even temperature at +22 C ( 0.5 C) at all shelves
The quantity of platelet concentrates that may be handled by any given agitator will vary according to whether these are apheresis or random donor harvested platelets. Apheresis-derived platelet concentrates are usually up to six times heavier than random single donor platelet concentrate packs. A motion failure alarm is critical for monitoring the agitator, and in the case of an incubator there is need for a temperature monitoring device similar to those in conventional blood storage refrigerators (visual and audible alarm systems indicating power failure or temperatures outside the range, and seven-day chart records).
23
External Ambient Temperature: Incubator performs in an ambient temperature range of up to +43 C 1 C and Relative Humidity of 60% Monitoring Motion of Agitator: A motion failure alarm Temperature Monitoring: Digital temperature (LED) display with 0.1 C graduation Visual and audible alarm system indicating temperature and power failure. Door ajar alarm Seven day chart recorder, or electronic record of maximum and minimum temperature attained Performance: Agitation at 1.5 inch (3.64 cm) side to side stroke, 6575 strokes/min.
PFS42*
INCUBATOR: PC900
* Helmer offers six different platelet incubators that can be matched with one or more platelet agitators. Each Agitator/Incubator provides chamber uniformity of 1 C
24
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
s PERFORMANCE DATA
Full load Half load
Alarm systems (motion and power failure): Independent, built-in motion alarms, including adjustable time delay and separate power switch. Power failure conditions signalled by the motion alarm after the delay period ends. s SPECIFICATIONS Capacity (maximum no. of platelet PSF15: 15 packs [60ml or 240ml volume] loaded): PSF42: 42 PSF84: 84 PSF396: 396 External dimensions in cm (H x W x D): PSF15: 32x40x24 PSF42: 35x46x36 PSF84: 35x84x36 PSF396: 157x94x68 Gross volume (litres): PSF15: 30 PSF42: 60 PSF84: 100 PSF396: 1000 PSF15: 12 PSF42: 24 PSF84: 39 PSF396: 114
50Hz 60Hz
3.8cm 58 70
3.8cm 60 72
s ENERGY REQUIREMENTS Rated voltage/frequency: 110120V, 50/60Hz, 220240V 50/60Hz s ADDITIONAL INFORMATION International standards equipment complies with: EN60601-1 EN61010 Shipping volume/gross weight: 2.5m3/125kg
Weight (kg):
PFS84 PFS396
s PERFORMANCE DATA
Full load Half load
50Hz 60Hz
3.8cm 58 70
3.8cm 60 72
Energy consumption: PSF15: 115V-0.2A 230V-0.4A PSF42: 115V-0.2A, 230V-0.4A PSF84: 115V-0.2A, 230V-0.4A PSF396: 115V-3A, 230V-2A s CODE: PA/02/f CODE: PA/03/f s COMPANY NAME AND ADDRESS Helmer 15425 Herriman Blvd Noblesville, IN 46060 USA Tel: +1 317 773 9073 Fax: +1 317 773 9082 E-mail: [email protected] www.helmerinc.com s FEATURES Design and construction: Ball bearing motors, circulation fans, one-piece perforated drawers and large diameter rollers for quiet operation Temperature indicator: Not applicable
s ENERGY REQUIREMENTS Rated voltage/frequency: 110120V, 50/60Hz 220240V 50/60Hz s ADDITIONAL INFORMATION International standards equipment complies with: EN60601-1 EN61010 Shipping volume/gross weight: PSF15 PSF42 PSF84 PSF396 .19m3/16kg .19m3/27kg .30m3/44kg 2.83m3/164kg
* Helmer offers four different flatbed platelet agitator models for different capacity needs (not evaluated by WHO).
25
A plasma thawer is a water bath designed to offer rapid and safe defrosting of frozen plasma. It achieves this through the agitation of the plasma in a bath at 37 C or by directing a stream of warm water to the plasma pack. Defrosting from -30 C to 0 C is achieved within approximately 15minutes. The plasma packs may be introduced at random or as a batch depending on the model selected. A plasma thawer achieves a uniform and quality standard of defrosted plasma for transfusion or other use. The limitation is the risk of leakage of plasma from a cracked plasma pack. Unless a dry type of plasma thawer is selected or the plasma packs are packed in leak proof plastic during thawing, water may seriously affect the readability of the labels on the plasma packs. The bath can be cleaned and fresh water put in as necessary.
CHAPTER 6
Plasma thawers
Specification Reference: BTS/PT/IN.1 Purpose of Equipment: To thaw rapidly frozen plasma Type of Equipment: At 37 C water bath. Plasma packs held in special containers and constantly agitated uniformly in the bath until thawing is complete. Packs remain dry Laboratory Test Procedure: Standard Test Procedure: BTS/ PT.1/Proc. 1 Construction: Internal: Corrosion resistant material, easy to clean and no staining External: Corrosion Resistant (CR at least 1mm thickness) Design: Chest type, lid optional Easy loading and removal of plasma packs Easy to empty water when required Electrical Characteristics: Nominal input voltage: 220/240V 50Hz or 110V 60Hz AC single phase Equipment meets internationally accepted electrical safety specifications such as that of IEC Internal Temperature Control: Tamper resistant temperature control set at 37 C ( 1 C) External Ambient Temperature: Performs in an ambient temperature of 10 C to 30 C ( 5 C) Thawing Time: A full load of flat plasma packs (approx. 250ml volume) with a core temperature of -30 C ( 1 C) is thawed completely in less than 20 mins Warning Systems: Digital temperature (LED) display with 0.1 C graduation Visual and audible alarm system indicating temperature outside range Audio/visual alarm if water level drops Audio/visual alarm if plasma pack leaks during thawing if pack is not in a leak proof container
Key features
Plasma thawers should be able to thaw all types of plasma packs, either folded or flat in form, and apheresis packs. In some designs, it may be necessary to protect the ports on the pack by overwrapping, to prevent water leaking through the port into the bag. Modern plasma thawers ensure that the operator does not get his hands wet. Bench top or floor standing models are available. Important features are the water drainage facility, alarm systems and the speed of thawing.
Alarm systems
The plasma thawer may have an alarm to warn the user of low water levels in the bath. The alarm for high temperature should also be fitted to ensure that the plasma packs are thawed at 37 C. In some models using open systems, the plasma pack may leak on thawing
26
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
s ENERGY REQUIREMENTS Rated voltage/frequency: 120 or 240V, 50/60Hz Energy source: AC Electricity Min. voltage: 105 VAC for 120 VAC unit. 210 VAC for 220VAC unit Max. voltage: 135 VAC for 120 VAC unit. 270 VAC for 220VAC unit s ADDITIONAL INFORMATION International standards equipment complies with: CE, UL 2601-1, CSA C22.2 No. 601.1, FDA # BK960012 Shipping volume/gross weight: 0.226m3/ 19 kg s SPARE PARTS FOR 10 UNITS (ALL ACCESSORIES INCLUDED WITH UNIT)
s CODE: PT/01 s COMPANY NAME AND ADDRESS PhotoTherm 110 Sewell Avenue Trenton, NJ 08610 USA Tel: +1 609 396 1456 Fax: +1 609 396 9395 E-mail: [email protected] www.cytotherm.com s FEATURES Materials: Bath is white polypropelyne. 3 isolated sections. Rack is white PVC. Metalecyne bladders separate tempered water from plasma bags. Thawer has rocking agitation. Temperature indicator: Large digital thermometer Alarm systems: Over-temperature alarm and turn-off when temperature reaches 38 C; independent thermostat that turns off heaters at 42 C; low water level alarm and heating turn-off. Senses plasma leaks. Loading plasma packs: Plasma packs are placed on the bladder and the lid closed. Plasma bags and hands stay dry. Temperature control: Digital s SPECIFICATIONS Capacity in litres: 12 Max. no. of plasma packs: 6 x 450ml or 3 x 1000ml External dimensions in cm (H x W x L): 33 x 56 x 56 Gross volume (litres): 103 Weight (kg): 16 s PERFORMANCE DATA
Full load Min load
s CODE: PT/02 s COMPANY NAME AND ADDRESS PhotoTherm 110 Sewell Avenue Trenton, NJ 08610 USA Tel: +1 609 396 1456 Fax: +1 609 396 9395 E-mail: [email protected] www.cytotherm.com s FEATURES Materials: White PVC. Metalecyne bladders separate tempered water from plasma bags. Has two isolated sections. Temperature indicator: Large digital thermometer Alarm systems: Over-temperature alarm and turn-off when temperature reaches 38 C; independent thermostat that turns off heaters at 42 C; low water level alarm and heating turn-off. Senses plasma leaks. Loading plasma packs: Plasma packs are placed on the bladder and the lid closed. Plasma bags and hands stay dry. Plasma bag is massaged by pressurizing different sections of the bladder. Temperature control: Digital
27
Thawing time: 300ml bag of 250ml plasma Water bath temperature: 37 C Noise level: Low
* Free video and literature available.
s SPECIFICATIONS Capacity in the bath (litres): 8 Max. no. of plasma packs: 4x450ml or 2x1000ml External dimensions in cm (H x W x L): 34 x 33 x 52 Gross volume (litres): 58 Weight (kg): 11.5 s PERFORMANCE DATA
Full load Min load
STRAP
Thawing time : 300ml bag of 250ml plasma Water bath temperature: 37 C Noise level: Low
15 mins/ 15 mins/ 6 bags 1 bag s CODE: PT/03 s COMPANY NAME AND ADDRESS PhotoTherm 110 Sewell Avenue Trenton, NJ 08610 USA Tel: +1 609 396 1456 Fax: +1 609 396 9395 E-mail: [email protected] www.cytotherm.com s FEATURES Materials: White polypropelyne internal and external Temperature indicator: Large digital thermometer Alarm systems: Over-temperature alarm and turn-off when temperature reaches 38 C; independent thermostat that turns off heaters at 42 C; low water level alarm and heating turn-off. Senses plasma leaks. Loading plasma packs: Plasma packs are loaded and unloaded with dry hands and gloves. Ports are kept sterile out of the water. Rocking turbo agitation. Will thaw 12 plasma bags with accessory 6 bag corral. Temperature control: Digital s SPECIFICATIONS Capacity in the bath in litres: 12 Max. no. of plasma packs: 12 x 450ml External dimensions in cm (H x W x L): 33 x 56 x 56 Gross volume (litres): 103 Weight (kg): 9 s PERFORMANCE DATA
Full load Min load
s ENERGY REQUIREMENTS Rated voltage/frequency: 120 or 240V, 50/60Hz Energy source: AC Electricity Min. voltage: 105 VAC for 120 VAC unit; 210 VAC for 220VAC unit Max. voltage: 135 VAC for 120 VAC unit; 270 VAC for 220VAC unit s ADDITIONAL INFORMATION International standards equipment complies with: CE, UL 2601-1, CSA C22.2 No. 601.1, FDA # BK960012 Shipping volume/gross weight: 0.153m3 / 17 kg s SPARE PARTS FOR 10 UNITS (ALL ACCESSORIES INCLUDED WITH UNIT) Magnetic pump Board Heater
Thawing Time: 300ml bag of 250ml plasma Water bath temperature: 37 C Noise level: Low
14 mins/ 12 bags
12 mins/ 6 bags
28
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
s ENERGY REQUIREMENTS Rated voltage/frequency: 120 or 240V, 50/60Hz Energy source: AC Electricity Min. voltage: 105 VAC for 120 VAC unit, 210 VAC for 220VAC unit Max. voltage: 135 VAC for 120 VAC unit, 270 VAC for 220VAC unit s ADDITIONAL INFORMATION International standards equipment complies with: CE, UL 2601-1, CSA C22.2 No. 601.1, FDA # BK960012 Shipping volume/gross weight: 0.153m3 / 12 kg s SPARE PARTS FOR 10 UNITS (ALL ACCESSORIES INCLUDED WITH UNIT) Magnetic pump Board Heater
thawing cycle is complete an audible tone sounds and the basket rises automatically out of the water for easy unloading. Temperature control: Temperature is controlled with a microprocessor based PID1 controller. The controller monitors water temperature through an RTD2 sensor and activates the high capacity heater to maintain constant water bath temperatures. s SPECIFICATIONS Capacity in litres: Max. no. of plasma packs (450 or 1000ml): External dimensions in cm (HxWxD): Gross volume (litres): Weight (kg) (without water): DH4: 18 DH8: 32 DH4: 4 (2501000) DH8: 8 (2501000) DH4: 38 x 47 x 37 DH8: 38 x 47 x 56 DH4: 70 DH8: 100 DH4: 26 DH8: 34
STRAP
s PERFORMANCE DATA
Full load Min load
Thawing time at 37 C: 250ml bag frozen flat 500ml bag frozen flat
Water bath temperature: 37 C factory setting, can be changed by operator Energy consumption DH4: 115V-6.0A 230V-3.0A DH8: 115V-10.0A 230V-5.0A s CODE: PT/O4 s COMPANY NAME AND ADDRESS Helmer 15425 Herriman Blvd Noblesville, IN 46060 USA Tel: +1 317 773 9073 Fax: +1 317 773 9082 E-mail: [email protected] www.helmerinc.com s FEATURES Internal lining of equipment: Stainless steel water tank External material: Powder coated steel Alarm systems for safe plasma thawing: Adjustable, high temperature alarm with visual and audible indicators. The thawing basket raises out of the water automatically when a high alarm occurs. Loading and retrieval of plasma packs: Plasma packs are loaded into an overwrap bag, which is placed immediately into the basket assembly while the basket is in the UP position, out of the water. The cycle start button automatically lowers the basket into the water. When the s ACCESSORIES Overwrap bag (1000): 400273-1 Digital solar thermometer: DTI Chamber cover for DH4: CT4 Chamber cover for DH8: CT8 s ENERGY REQUIREMENTS Rated voltage/frequency: 110120V, 50/60Hz, 220240V 50/ 60Hz Energy source: AC Electricity s ADDITIONAL INFORMATION International standards equipment complies with: EN60601-1, EN61010 Shipping volume/gross weight (including pallet): DH4 0.55m3 / 50 kg DH8 0.62m3 / 58 kg
* Helmer Plasma Thawing Systems have integrated agitation to achieve rapid thawing of up to four or eight bags simultaneously. Only Model DH8 was evaluated by WHO
1 2
PID: Proportional Band, Integral Function, Derivative Function RTD: Resistance Temperature Detector
29
Blood carriers
The data on blood transport has been compiled in collaboration with the WHO Department of Vaccines and Biologicals (V&B) on the basis of tests to determine that the equipment meets WHO/UNICEF specifications. All the cold boxes and carriers in this chapter also appear in Each blood transport Section E4 (cold boxes and box requires frozen ice vaccine carriers) of the WHO packs to ensure an Expanded Programme on Immunization Product acceptable cold life Information Sheets (PIS) (2000 Edition). 2 The code numbers remain standard with a different prefix to indicate the section, for example: E4/72-M describes the Apex Continental carrier as a vaccine carrier while B4/72-M gives its performance figures as a blood carrier. Each blood transport box requires frozen ice packs in order to ensure an acceptable cold life. The blood transport boxes produced below from the PIS also show the type and number of ice packs required. It is important to purchase always a second set of ice packs for each model because of inevitable losses, and also to ensure a constant set of frozen ice packs for routine use. Pre-filled ice packs are not normally recommended.They contain a eutectic agent that may have a lower freezing point than water, thus endangering whole blood or packed red cells which should never be frozen.
CHAPTER 7
Blood/platelet coolant
The coolant is a eutectic solution that has tremendous thermal energy capacity and stability at its thermal phase change temperature, typically +16 to +20 C. The coolants are kept at +4 C when they solidify, and are ready for use after two hours at room temperature. This phase change from solid to liquid thermally protects blood or platelets, and is far more efficient than ice/ water whose thermal phase change is at 0 C. The coolant is in a sealed pouch housed inside another bag, i.e., in a double bag in order to provide better protection. The most efficient cooling is achieved when the coolant pouch is in direct contact with the blood or platelet pack. However, the most important point is that the efficiency of the coolant depends on the insulating capacity of the blood transport box. The coolant is reusable and therefore cost-effective and eliminates the need for ice and water which can be messy. It provides temperature stability between +20 and +24 C in hot or cold climates, and is therefore useful in the following situations: 1. To rapidly cool whole blood from 37 C to 20 C 2. To assist to maintain the temperature of whole blood at approximately +20 C during transport prior to processing the components. 3. To provide temperature stability during platelet storage at +20 to +24 C; and 4. For the transportation of platelet packs between the laboratory and patient recipient.
See page 54 for a detailed checklist on selecting a blood transport box Document WHO/V&B/00.13
30
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
31
STRAP
STRAP
s COMPANY NAME AND ADDRESS Thermos 2550 W.Golf Road Suite 850 Rolling Meadows IL 60008 USA Tel 1 800 243 0745 Fax 1 847 593 5248 s SPECIFICATIONS Blood storage capacity: 2 units Weight fully loaded: 5.1 kg Weight empty: 1.8 kg External surface material: Polyethylene Internal lining material: Polyethylene Insulation material: Polyurethane Insulation thickness: 40 mm External dimensions H x W x L in cm: 24 x 24 x 33 Internal dimensions H x W x L in cm: 15 x 15 x 19 Blood storage dimensions H x W x L in cm: 10 x 10 x 18 Lid type and fixings: Removable No. of ice packs required: 4 No. of ice packs supplied: 4 Ice pack type: Thermos* Robustness in drop test: Fittings 3; Casing 3 Cold life without openings: 30 hrs at +43 C Standards complied with Test reports: CRL.A.9000 (1990) Meets WHO/GBSI Standard B4/BC.1 Shipping volume/gross weight: Minimum order: 1 s COMPANY NAME AND ADDRESS Blow Kings 53 C Mittal Court, Nariman Point Mumbai 400 021 India Tel +91(22)284 0120 / Fax +91(22)283 1412 E-mail: [email protected] s SPECIFICATIONS Blood storage capacity: 10 units Weight fully loaded: 21.7 kg Weight empty: 8.2 kg External surface material: Plastic Internal lining material: Plastic Insulation material: Polyurethane Insulation thickness: 55 mm External dimensions H x W x L in cm: 49 x 42 x 41 Internal dimensions H x W x L in cm: 37 x 30 x 26 Blood storage dimensions H x W x L in cm: 28 x 22 x 16 Lid type and fixings: Hinged No. of ice packs required: 24 No. of ice packs supplied : 24 (E5/12 of 0.3 litre. Cold life is 63 hrs when E5/19 (0.4 litre) is used) Ice pack types: E5/12, 19 Robustness in drop test: Fittings 2; Casing 5 Cold life without openings: ++ hrs at + 32 C, 65 hrs at +43 C Standards complied with: Test reports: Blow Kings* and Crown Agents meets WHO/UNICEF Standard E4/CB.4 Shipping volume/gross weight: 0.09m3/10 kg Minimum order: 1
* Cold life with blood calculated on basis of tests described in CRL A.9000 which established difference between performance with vaccine and blood.
32
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
STRAP
STRAP
s COMPANY NAME AND ADDRESS Dometic (ex Electrolux) 17 op der Hei 9809 Hosingen Luxembourg Tel +35 2 92 07 31 Fax +35 2 92 07 31 300 E-mail: [email protected] www.dometic.com s SPECIFICATIONS Blood storage capacity: 15 x 450 ml Weight fully loaded: 21 kg Weight empty: 11 kg External surface material: Polyethylene Internal lining material: Polyethylene Insulation material: Polyurethane foamed with cyclopentane Insulation thickness in cm: 911.5 External dimensions H x W x L in cm: 50 x 55 x 47 Internal dimensions H x W x L in cm: 27 x 34 x 26 Blood storage dimensions H x W x L in cm: 19 x 26 x 18 Lid type and fixings: Hinged No. of ice packs required: 12 No. of ice packs supplied: 12 Ice pack types: E5/09 Robustness in drop test: Fittings 2; Casing 1 Cold life without openings: ++ hrs at +32 C, 108 hrs at +43 C Standards complied with : Test reports: UNIVALLE E4/3010 (1998). Meets WHO/UNICEF Standard B4/CB.4 Shipping volume/gross weight: 0.15 m3/15.6 kg Minimum order: 1
33
STRAP
s COMPANY NAME AND ADDRESS Blow Kings 53 C Mittal Court, Nariman Point Mumbai 400 021 India Tel +91(22)284 0120 Fax +91(22)283 1412 E-mail: [email protected] s SPECIFICATIONS Blood storage capacity: 20 units Weight fully loaded: 49 kg Weight empty: 20 kg External surface material: Plastic Internal lining material: Plastic Insulation material: Polyurethane Insulation thickness in cm: 11 External dimensions H x W x L in cm: 78 x 54 x 55 Internal dimensions H x W x L in cm: 56 x 32 x 33 Blood storage dimensions H x W x L in cm: 46 x 23 x 19 Lid type and fixings: Hinged No. of ice packs required: 52 No. of ice packs supplied: 52 (E3/12 of 0.3 litre. Cold life is 145 hrs when E5/19 0.4 litre is used) Ice pack types: E5/12, 19 Robustness in drop test: Fittings 2; Casing 5 Cold life without openings: ++ hrs at +32 C, 145 hrs at +43 C Standards complied with: Test reports: ERTL(W)/2001 ENV 421*. Meets WHO/UNICEF Standard E4/CB.2 Shipping volume/gross weight: 0.26m3/27 kg Minimum order: 1
* Cold life with blood calculated on basis of tests described in CRL A.9000 which established difference between performance with vaccine and blood.
34
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
8.1 Overview
Temperature monitoring devices are critical to the quality management of the blood cold chain.Technology for monitoring the temperature of blood cold chain equipment has evolved from the traditional thermometer to electronic versions that have an accuracy of at least 0.2 C. However, according to a recent survey conducted by WHO on the status of the national Quality management blood cold chain, the traditional requires that a max/min thermometers are still in record is kept of the use in many developing countries.
CHAPTER 8
temperatures of equipment storing blood and blood components: the chart recorder readily provides this
Similarly, the traditional temperature recorder chart remains the simple, effective tool used by the majority of peripheral centres for monitoring the temperature of a blood bank refrigerator or plasma freezer. Quality management requires that a record is kept of the temperatures of equipment storing blood and blood components, and the chart recorder readily provides this. Its major drawback is the requisite consumables such as ink, chart paper and pens, which often run out well before the equipment becomes obsolete. Improvements to meet these shortcomings are now commercially available, mainly in the electronic display and capture of data.
35
connected from an enabling temperature monitoring port at the back of the blood refrigerator leading to a remote device able to display a warning light (green to red) and/or alarm sound. The device is placed at a site that is permanently manned, e.g., the hospital switchboard. Several pieces of blood storage equipment may be wired in this way. The devices can also warn of a power failure to the equipment being monitored. Finally, there are new devices for monitoring up to 16 blood bank refrigerators simultaneously. Temperature probes are connected from an enabling temperature monitoring port at the back of the blood refrigerator leading to a multi-temperature data logger device. The device is permanently connected to a PC. The information can thus be continuously displayed and automatically saved and printed if required.The software enables an alarm to be set off if temperature settings are exceeded, and quality temperature charts to be printed. The PC can continue in normal use without affecting the temperature recording.
The first three windows will monitor whether the blood has been exposed cumulatively to a temperature of +10 C or above. As soon as +10 C is exceeded the first window starts to turn blue. If the temperature remains above +10 C or at every successive exposure to this temperature, the blue colour will migrate through windows 1, 2 and 3. The higher the temperature, the faster the blue colour will spread through these windows. Window 4 will start to show traces of blue immediately the temperature in the container exceeds +17 C. The coloration in the windows is easy to observe and, although coloration may stop, is irreversible.
Use
The BTTI is not intended to replace existing quality assurance measures for the safe transportation of blood components. It is a simple tool to assist personnel handling blood components to decide to use or discard a particular blood consignment. In this way, the BTTI transport card contributes to the goal of increasing the safety of the global blood supply in line with WHO recommendations related to the blood cold chain. The BTTI will be useful to monitor the temperature of whole blood or red cell suspensions in many different situations: 1. Storage in cold boxes in the case of breakdown in electricity or other powered supply 2. Shipment using blood transport boxes from one blood bank to another 3. Movement of blood from the blood bank to the bedside 4. Return of unused blood from the point of potential use to the hospital blood bank. N.B. The BTTI will not indicate temperatures below +10 C. This means that if the temperature inside the box drops because of incorrect ratio of ice packs to red cell packs, or due to a drop in environmental temperature, there will be no colour change detected.
How it works
Based upon the migration of a chemical through a paper wick, the BTTI is an indicator on a card that upon activation shows colour changes when the cumulative temperature of exposure exceeds +10C. The BTTI has four windows labelled 1 to 4 that will turn blue upon undue thermal exposure, as follows:
36
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
STRAP
s COMPANY NAME AND ADDRESS Hyoda Instruments Corporation 16-10 Kitahorie 1-Chome Nishi-Ku, Osaka 550-0014 Japan Telephone: 81 (6) 65 38 12 91 Fax: 81 (6) 65 39 26 17 E-mail: [email protected] s SPECIFICATIONS Temperature range: -30 C to +50 C Hours per cycle: 24 hrs External dimensions in cm: 28.5 x 10 External materials: aluminium Weight: 15 kg No. per package: 1 Test Reports: CATR.A9105 (1985). Meets WHO/UNICEF Standard E6/TH.2 COMMENTS Capillary tube at the bottom of the case. Length of capillary: 3m. Sensor of probe (dxl): 12 mm x 150 mm. Thread connection:1/2 NPT. Minimum order: 1 Shipping volume/gross weight (1 pk): 0.100 m3/15 kg
s COMPANY NAME AND ADDRESS Pacific Transducer Corporation 2301 Federal Avenue Los Angeles, CA 90064 United States of America Tel: 1 (310) 478 11 34 Fax: 1 (310) 312 0826 s SPECIFICATIONS Temperature range: -40 C to +70 C External dimensions: 9 x 10 cm External materials: aluminium Weight: 0.6 kg No. per package: 1 Test Reports: CATR. Z.9955/2 (1978). Meets WHO/UNICEF Standard E6/TR.2 s COMMENTS Includes polyethylene bag for protection against internal corrosion. Also available in Fahrenheit. Extra charts: Part No: 615.47CB (-40 to +70 C). Dry stylus operation. Carrying case, Part No. 615.99. Important: give entire product description and specify time/temperature range in your order. Shipping weight/volume: 0.91 kg/0.0013 cm3
Item
Quantity
Recorder
Item Code Quantity
1 100 1
37
PHOTO?
s MODEL: TINY TTM TYPE G IP68. s CODE: TD/04 (PIS E6/44) s COMPANY NAME AND ADDRESS Remonsys Ltd. (Distributor for Gemini Data Loggers [UK] Ltd.) The Stables Church Hanborough Witney Oxfordshire OX29 8AB United Kingdom Telephone: +44 (1993) 886996 Fax: +44 (1993) 886997 E-mail: [email protected] s SPECIFICATIONS
s COMPANY NAME AND ADDRESS Remonsys Ltd. (Distributor for Gemini Data Loggers [UK] Ltd.) The Stables Church Hanborough Witney Oxfordshire OX29 8AB United Kingdom Telephone: +44 (1993) 886996 Fax: +44 (1993) 886997 E-mail: [email protected] s SPECIFICATIONS Temperature range: -40 C to +75 C Accuracy: 0.2 C Measuring interval: 0.5 secs to 4 hrs 48 mins Memory size: 1800 readings Size (dxl): 30 x 50 mm External materials: plastic case Weight: 0.05 kg No. per package: 5 Power source: battery 3.6 V (1/2AA) Battery life available: 2 years Test Report: Univalle, 1992. No WHO/UNICEF Standard exists s USE Functions as a reusable cold chain monitor for use in vaccine refrigerators, shipments and cold chain studies. The TTM is battery operated and small enough to fit inside a 35 mm plastic film container. It stores data that can be downloaded by special cable to the serial port of a PC with MS Windowssupported software. Shipping volume (5 pks): 555 cm3
Temperature range: -40 C to +75 C Accuracy: 0.2 C Measuring interval: 0.5 secs to 4 hrs 48 mins Memory size: 2048 readings Size (L x B x H): 70 x 60 x 50 mm External materials: glass reinforced plastic Weight: 150 g No. per package: 5 Power source: battery 3.6 V Battery life available: 2 years Test Report: Univalle, 1992. No WHO/UNICEF Standard exists s USE Functions as a reusable cold chain monitor for use in vaccine refrigerators, shipments and cold chain studies. This version of Tiny TTM has a rugged enclosure. It stores data that can be downloaded by special cable to the serial port of a PC with MS Windows-supported software. Shipping volume: 0.001 cm3
Item
Quantity
1x5 1 1
Item
Quantity
1x5 1 1
38
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
STRAP
STRAP
s COMPANY NAME AND ADDRESS OCEASOFT Cap Alpha, Avenue de lEurope, Clapiers 34940 Montpellier Cedex 9 France Telephone: +33 (4) 67 59 36 30 Fax: +33 (4) 67 59 30 10 E-mail: [email protected] s SPECIFICATIONS Temperature range: -40 C to +85 C Accuracy: 0.3 C Measuring interval: 1255 mins Memory size: 2048 measurements Size (dxl): 17.35 x 5.89 mm External materials: Stainless steel Weight: 3.30 g No. per package: 1 Power source: internal Lithium battery Battery life available: 5+ years or 1 million measurements Test Report: CEMAGREF and LCIE approved. No WHO/UNICEF Standard exists s USE Functions as a reusable cold chain monitor for use in vaccine/blood refrigerators, shipments and cold chain studies. It displays and stores data that can be downloaded to a PC with MS Windows-supported software. Reading software available separately. Shipping weight/volume (1pk): 1.kg/0.002 m3
s COMPANY NAME AND ADDRESS Remonsys Ltd. (Distributor for Gemini Data Loggers [UK] Ltd.) The Stables Church Hanborough Witney Oxfordshire OX29 8AB United Kingdom Telephone: +44 (1993) 886996 Fax: +44 (1993) 886997 E-mail: [email protected] s SPECIFICATIONS Temperature range: -30 C to +70 C Accuracy: 0.1 C Measuring interval: 160 mins Memory size: 8K Size (dxl): 195 x 100 x 43 mm External materials: ABS plastic case Weight: 300 g (without sensors); 1000g (with 4 sensors) No. per package: 1 Power source: internal Lithium battery Battery life available: 10 years Test Report: USDA approved. No WHO/UNICEF Standard exists s USE Functions as a reusable cold chain monitor for use in vaccine refrigerators, shipments and cold chain studies. It displays and stores data that can be downloaded by special cable to the serial port of a PC with MS Windows-supported software. Comes equipped with 4 sensors (2 x 6m and 2 x 20m). Shipping weight/volume (1pk): 1.3kg/0.006 m
3
Item
Quantity
1 1 1 1
Item
Quantity
1 1
39
s COMPANY NAME AND ADDRESS (MARKETING) Berlinger & Co. AG 9608 Ganterschwil Switzerland Tel: +41 71 982 88 11 Fax: +41 71 982 88 39 E-mail: [email protected] Internet: www.berlinger.ch s SPECIFICATIONS Temperature thresholds: +10 C and +17 C External dimensions: 12 x 15 cm No. per pack: 250 pk Minimum order: 500 pk (2 packs) Test report: Lab tested at Which Laboratories UK. WHO field tested in 6 countries (1999) s COMMENTS BTTI must be kept at +4 C or below for four hours before activation Shipping net weight: 1.7 kg/pack
40
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
In addition to the blood cold chain equipment, there is a need for devices and accessories to support the equipment, broadly grouped under the following headings.
CHAPTER 9
is not stable, voltage fluctuations may damage the electronic components of the cold chain equipment
41
is wired also to the hospital emergency power generator. If the blood bank is separate from the hospital facilities, i.e. stand-alone, there is a need to obtain the appropriate equipment for use, bearing in mind future needs.
move around. However, they are not meant for continuous operation over a period of years and, given their light weight, can be stolen easily. Manual versus electric (automatic) starting: Hand starting is far less expensive and more robust. However, automatic starting may be needed when power cuts are frequent and cold chain staff are absent on nights or weekends, since the battery will automatically take over. Hand starting is preferable for units up to 3 cylinders. For units up to 6 cylinders, it is preferable to have both options. When electric starting is selected, be sure to include a starting battery in the budget request since batteries are not normally supplied unless specified. Spring starters are an alternative that eliminates the need for a starting battery and charging equipment. Type of cooling: Air-cooled units are easier to maintain than units with water cooling. Mounting: A separately mounted fuel tank is often preferable to an engine-mounted tank, which is subject to vibrations. Meter: A meter to record the number of hours run is a very useful feature. It helps the operator plan preventive maintenance. Spare parts: The following should be included: set of fan belts (1) water pump (1) fuel pump, with plunger and delivery valve (1) set of front and rear oil seals (1) gasket O/H set (1) set of piston rings (1) sets of decarbonizing joints (2) set of nozzles (1) set of inlet and exhaust valves, with guides (1) set of brushes (1) set of rubber parts (2) (if used at places liable to distortion) set of hose pipes (1) air/oil/fuel filters (5) Other recommended items: Mains isolator switch; fuse protection for all phases for the generator; a see-through fuel gauge (this is a cheap feature which enables the operator to see at a glance whether the unit needs refilling). Soundproofing: Soundproofed enclosures are usually expensive and could be the subject of a separate bid. Locally made brick enclosures are often a cheap
Estimating the size of the generator for the stand-alone blood bank
All facilities or equipment to be connected to the emergency generator need to be correctly included, e.g., cold rooms, laboratory equipment, water baths, incubators for cross matching, refrigerators, lights, Most blood cold microscopes, etc. that are essential chains in developing to deliver the service. This countries need a information, plus data on standby generator temperature and altitude, are unless the mains essential if the supplier is to make current is very an accurate estimate of the size of reliable standby generator required. To ensure accurate information and avoid a costly waste of limited resources, it may be prudent to use a qualified engineer to perform this function, especially when a new blood bank is built. The generator is de-rated as follows: 1% of its capacity for every 100 metres above sea level, 1% for every 5.5 above 20 C. Example: Size required 14 KVA (determined by measuring starting and running currents) Altitude above sea level + 500 m de-rating 5% Ambient temperature 31 C de-rating 2% Total de-rating 7% Size of unit to be purchased 15 KVA (14 + 7x14/100) Most cold chains operate on standby generators only during power cuts. If a generator needs to operate continuously on full power, rate it at 80% of the indicated output. Most manufacturers indicate outputs as continuous (normal) or standby (emergency boost).
42
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
soundproofing option and, in the case of units installed outside, provide protection against the weather. Fuel consumption: Ask for fuel consumption figures per hour and verify the accuracy of the suppliers figures against similar models in local use.
Blood packs
When pre-supplied trays are not provided, it is necessary to design a system to hold the packs. The key points in designing a tray for holding blood packs are: 1. The material used must be strong and sturdy, e.g. perspex or varnished wood. 2. The design must allow the blood packs to stand straight when about three quarters full.
Trays and pack holders provide for 3. When full, the tray should have easier inventory a maximum weight of 3kg to management allow for ease of carrying a
single tray. 4. The tray surface must be smooth to avoid any scratches to blood packs since they are made of plastic. 5. The trays should be washable without damaging the construction material. 6. The trays should be moisture resistant.
Plasma packs
Plasma packs are different. Plasma has to stay frozen, and the best way to keep it frozen and for easier handling is for the packs to stay flat by putting the wet plasma pack in a pack holder. The tray should still have a maximum weight of 3kg to allow for easier handling. Once the packs are frozen they may be removed from these trays and packed in suitable cartons in the freezer which are properly labelled for ease of identification. Manufacturers of plasma derivatives prefer single packs frozen flat for ease of handling.
43
s COMPANY NAME AND ADDRESS Advance Galatrek Advance Park Wrexham LL14 3YR United Kingdom Tel: +44 1978 82 10 00 Fax: +44 1978 81 08 52 E-mail: [email protected] s SPECIFICATIONS Nominal voltage: 220 V Continuous power: 2500 VA Frequency: 50 Hz, Phase I Input voltage range: 145-278 V Output voltage range: 198-225 V Input connection: 2 metre fly lead Output connection: socket with plug (specify type required) Indicators on input: green neon Indicators on output: red neon External materials: grey painted steel Weight (unpacked): 10 kg External dimensions (unpacked) in cm: 15.3 x 16.7 x 35.5 No. per package: 1 Test Report: CATR.A.92071 (1988). Meets WHO/UNICEF Standard E7/VR.1 s COMMENTS Unit is fitted with a circuit breaker, as well as a 612 min delay cut-out on input, to protect against high/low voltage. Minimum order: 1 Shipping net volume: 0.091 m3
44
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
CHAPTER 10
Equipment maintenance
10.2 Management of repairs
Equipment repairs are necessitated by failure of components of the equipment and often misuse of the equipment by the user. A coordinated programme is needed to ensure that equipment is repaired in a timely and proper fashion and, in turn, the effectiveness of such a programme will depend on the availability and accessibility of skills, tools and spare parts.
Equipment maintenance is part of The availability of the global Health Care Technology spare parts does Management process. The aim of not guarantee the an equipment maintenance uninterrupted and programme is to assure the proper performance maximum working life of the equipment. This can be achieved of the blood cold by addressing the two key chain equipment components of equipment maintenance, i.e. Preventive maintenance and the Management of repairs. Both components should be part of the quality management system of the blood bank, necessitating a clear policy statement on the maintenance of equipment in general and supported by Standard Operating Procedures.
Non Critical
45
Gaskets, door liners Temperature recorder charts or data loggers, ink Light bulbs, switches, nuts, bolts, fuses, refrigerant gas
NO
NO
NO
NO
NO
5 6
46
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Equipment is too old and spares no longer accessible. Capital for the timely replacement of old equipment not budgeted for or available. Limited local market for the equipment. Uneconomic to hold a realistic spares inventory. Import/currency restrictions. Management of the inventory and its security. Poor control, monitoring and distribution of the spares often results in unnecessary shortage of spares.
More reading on the management of spare parts and preventive maintenance will be available in the WHO learning materials on the Management of the Blood Cold Chain. This Guide does not list all possible spare parts. Each manufacturer listed, however, can provide a list of essential spare parts for a given quantity of equipment purchased. The WHO Procurement Services can also provide guidance on the procurement of all medical supplies (fax +4122 791 4196, e-mail: procurement@ who.int).
47
The purchase of cold chain equipment should be considered as a long-term investment. The equipment should last for many years and give a good return of service if rigorous selection criteria have been applied.
CHAPTER 11
2 The equipment maintains its performance and appearance 3 Although a quality product is often more expensive, its longer life span and low maintenance costs generally more than justify the investment.
Costs
Information is needed on the market situation, i.e. what products are on offer at what price. Note that manufacturers change and update their models regularly, which may also affect prices. The WHO Procurement Services can be consulted for up-to-date information and sources for manufacturers (contact procurement@ who.int). For any purchase over US$15,000, the WHO Procurement Services will automatically seek a minimum of three offers from different sources. Issues to consider are the following: 1 The budget available for capital expenditure on blood cold chain equipment 2 Is the equipment being imported directly by the purchasing organization or through a local import agent? 3 If it is being directly imported by the organization, the following costs should be checked: a the Free on Board (FOB) price. FOB is the cost of the item from the manufacturer or his agent without any shipment costs; b the Cost, Insurance and Freight (CIF) charges. CIF includes the cost of the item, freight charges including handling fees and insurance. This is sometimes referred to as the landed cost of an item: i.e. the cost to bring it into the country. If
durable and gives trouble-free service There are variations within each
Quality
A history and survey of existing equipment will give an indication of which manufacturers produce quality products. Many colleagues in the industry can be
48
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
the equipment is being bought locally or through a local import agency, the main consideration is the landed cost to the laboratory; c Customs clearance charges unless the institution is exempt from Customs Duty for such items; d additional costs for any accessories or spare parts needed, such as temperature recorder charts and ink.
2 increased value for money. Suppliers give their best quotations secretly in order to secure a contract. The major disadvantage is that it is a lengthy procedure.
Informal tendering
Informal tendering is a procedure commonly used by an organization when there are few suppliers, who are generally known within or outside the country. The procedure is also adopted when the value and quantity of the equipment to be acquired is relatively low. When the informal tendering procedure is used, the specifications and quantities of equipment required are compiled and submitted to known suppliers, who are usually given a relatively short time to submit their bids. The advantage of informal tendering is that the procedures are more rapid and generally predictable, as the equipment available from each supplier is often already known. The major disadvantage of the informal tender is that there may be a relatively limited range of equipment from which to choose. It is advisable for organizations to purchase equipment exclusively through formal or informal tendering procedures. Figure 4 gives an example of a specification for tendering which may be useful as a guide.
Formal tendering
A formal tender procedure is one where details of the equipment to be bought, their specifications and the quantities required are published using approved national and/or international publications, such as government gazettes or other widely read media. The publication is an invitation to suppliers to submit bids for the tender, or formal binding quotations for the equipment, delivery date and related conditions. Usually a closing date for the submission of bids is given, and all bids remain sealed until this date, at which time they are opened together, in the presence of all bidders if possible. A formal tendering procedure is commonly used when high value equipment is to be bought, single or multiple. The advantages of formal tendering are: 1 an increase in transparency of the purchasing process. Suppliers consider the process as conducive to fair trading;
49
defined specifications
In some cases, the donor may wish to provide specific blood cold chain equipment. However, great as the need for donations of equipment may be, it is essential to ensure that the equipment to be supplied meets the defined specifications, e.g. power rating and preferred brands. Look at the following checklist of questions to help in assessing whether donated equipment will meet your requirements.
4 Does it meet your current needs? 5 Does it have the correct capacity? 6 Is the power rating appropriate for the local energy source? 7 Is the equipment affordable, including its maintenance costs? 8 Is the equipment user friendly and suitable for the personnel? 9 Are spare parts readily available? 10 Are local service contracts available? In addition, Programme Managers should ensure that cold chain equipment is free of chlorofluorocarbons (CFC-free). Annex 2 provides a user-friendly summary of the recommendations outlined in the Montreal Protocol on CFCs as related to the blood cold chain.
50
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
a) Input voltage 220/240V 10% 50HZ AC single phase without transformer b) Wired-in plug Four years consumables should be included and detailed in the offer At least 1 year Recommended list of spare parts and prices
51
Figure 5. Selection of appropriate blood cold chain equipment according to the energy source Adapted from the WHO-EPI Product Information Sheets (2000)
YES
YES
NO
YES
YES
NO
adequate ventilation to reduce stress on the compressor unit of the cold chain equipment; An alternative power source for use in the event of the failure of the normal electricity supply, e.g. a standby generator.
11.5 Quantity
The number of units to be bought will depend on the findings of the needs assessment and estimate of future requirements. The major points to note are as follows: The quantity of units required directly relates to the capacity of the equipment. Tables 6, 7 and 8 below
give a guide on the capacity of the different storage equipment. However, because of the possibilities of breakdown and the fact that blood should not be stored outside acceptable temperature ranges for more than 30 to 60 minutes, alternative cold chain equipment should be available and have adequate capacity to accommodate products from another unit in an emergency; it is important to allow for growth in the number and activities of blood transfusion services and hospital blood banks. The quantity and capacity of equipment to be purchased must therefore take possible needs for up to 5 years into account.
52
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Table 8. Classification of blood transport boxes by capacity and cold life (WHO Specification reference applies to each individual box)
Classification by capacity and cold life BB1 (hand carrier) <4 14 30 BB2 (small capacity short range) 510 415 132 BB3 (large capacity short range) 1120 1527 60 BB4 (large capacity, long range) [>20] 1527 140
Approx. number of blood bags (450 ml) Approx. internal storage capacity in litres Cold Life in hours with the recommended ice packs or coolant pouches
NB. Transport Boxes are classified only according to the volume available for blood storage not for ice packs. The manufacturer makes provision for the ice packs.
Figure 6. A guide to estimating the type and quantity of blood refrigerators, plasma freezers and transport boxes required
Level Central Handling capacity needed for: 3 000 donations per month Equipment needed: Cold room Refrigerators Freezers Freezer rooms* Blood transport box* Quantity needed 2 (9 cu.m each) 8 (80100 units each) 4 (80100 units each) 2 (6 cu.m each) BB4:15 BB3: 5 BB2: 5 BB1: 10
Component production
Based on 67 units transfused per hospital bed/year plus allowance for waste
or an irrevocable letter issued by the bank guaranteeing payment. The latter is usually requested by suppliers from outside the country, and is referred to as an Irrevocable Letter of Credit. Organizations of the United Nations system, the Red Cross and most nongovernmental organizations (NGOs) will not accept Letters of Credit. For standard equipment, 30 days payment terms is the norm.
53
11.7 Checklists
In addition to the general checklist featured on pages 49 and 50, and the Needs Assessment featured in Annex 1, the following checklists summarize the most important elements to consider in selecting blood cold chain equipment.
How long will box and ice packs keep the correct temperature for? This will depend on size of box, load, time and distance. It is necessary to validate the different boxes and conditions locally, so that your centre will have a clear idea of how many ice packs per box will be needed to transport blood products to different locations. 3 Weight: How will the cold box be carried? Weight fully loaded and durability can be graded according to how the box will be transported (by vehicle, bicycle or hand-carried) and how roughly it will be treated. For example, durability will be more important than weight for a box transported by vehicle over rough roads so it should have a good rating in the drop test.The reverse will apply to handcarried boxes where weight will be more important. 4 Durability: To what conditions will the cold box be exposed? 5 Ice packs: Are ice packs included? At the time of placing an order it is important to check if ice packs are included with the box or not. If they are not included, select ice packs that will fit the chosen box and simultaneously place an order for them. Always order two sets of ice packs: one set to be used while the other is being frozen. 6 Price: Which cold box meets requirements 1, 2 and 3 for lowest cost? Remember to consider shipping costs. Choose the cold box that costs the least yet still fulfils programme requirements. However, it is important to note here that the prices on the sheets do not include shipping costs. Insulated boxes are bulky so shipping costs can often represent a high proportion of the total cost. We therefore strongly recommend that programme managers investigate shipping costs before making a final choice.
54
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
3 Is it a random access or batch thawing process equipment, i.e. is the thawing of each plasma pack monitored separately or only as a batch. 4 How long does it take to thaw a plasma pack or a batch of plasma packs? 5 Reliability: Are repair facilities and spare parts available for the plasma thawer to be purchased? 6 Temperature monitoring? Do you have a fixed temperature display and alarm system? 7 Price: Which plasma thawer meets requirements 16 at the lowest cost? 8 Do you need user and service manuals in the official language of your country? 9 Training: Are the users and those in charge of maintenance of the equipment properly trained?
Installation requirements
Installation requirements will to some extent be determined by the location of the facilities where the equipment will be used. It is important to state whether the supplier will be expected to install each unit of equipment at the sites where they will be used, or whether the equipment should be delivered to one central site. In the latter case, the installation will be the responsibility of the buyer.
55
It will generally be more expensive per unit if the supplier is expected to install all the equipment, although this will depend on geographical and other considerations prevailing in the country. The importance of users and technicians training is often underestimated and therefore under-budgeted. A cold chain with good equipment, but insufficiently trained staff may seriously endanger blood safety. Training must be taken into consideration before selecting any blood cold chain equipment. If the supplier is expected to train users in the installation, maintenance and servicing of the equipment, the purchasing organization will need to allow for this in the budget. The installation of cold chain equipment is relatively easy if the manufacturers instructions are followed precisely. Many blood transfusion services and large hospitals employ a technician with responsibility for the installation and training of users in the maintenance of cold chain equipment and who generally receive direct, supervised training from equipment suppliers. This is a much cheaper and more practical approach.
quickly, such as hinges, evaporators and door gaskets, than those that last longer, such as compressors. Manufacturers should therefore be requested to provide a list of recommended spare parts that will be required over a five year period. Spare parts are generally centrally stored under the care of the technician who has national responsibility for the maintenance of cold chain equipment. This assists in controlling wastage and theft and enables the technician to plan for replacement items.
Commissioning
Commissioning, i.e. installation and certifying the equipment ready for use, reassures the client that the equipment is working properly. At least 10% of the payment due should be withheld until a full commissioning test has been completed satisfactorily. The equipment should be validated as part of the quality management process in the blood bank, i.e., the test procedure should run at least 48 hours. Cooling phase, alarms, temperature monitoring and temperature controls should be included in the test.
Guarantee
The supplier generally provides a guarantee for the equipment. This guarantee is generally in one of two forms: 1 An initial guarantee of the entire equipment for a period of between 6 months to 2 years or more. This guarantee may be for replacement or full repair costs. 2 Following this period, the supplier may give a full guarantee for part of the equipment for a further period, e.g., a compressor. It is important to remember that, unless poor quality equipment has been selected, the equipment is still fairly new during the period of guarantee and is less likely to break down. After the period of guarantee, the cost of the maintenance and repair of the equipment falls to the user.
56
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Information provided by: Name: Position Date: Tel: 1. Blood Cold Chain Equipment 1.1 Is the procurement of equipment and spares, training and maintenance coordinated nationally? 1.2 Is there a nationally controlled inventory of blood cold chain equipment? 1a. Equipment in current use at the institution Please list below by type of equipment available at the Institution. You may need more space.
Type of Equipment Model/Manufacturer Ser. No. Internal capacity(l) Maximum packs possible Date first used Temp. monitors Tchart Alarm LED CFC-free refrigerant Yes No
ANNEX 1
Blood refrigerator
Plasma freezer
Platelet Agitator
Others
1b. Projected need for the following equipment in the next 12 months Plasma freezers Blood bank refrigerators solar type ice-lined standard electric Walk-in plasma freezer room Walk-in blood refrigerator room Plasma thawers Platelet agitators Temperature monitoring devices Chart recorders Portable digital thermometers Others
57
2. Volume of blood components handled per month Whole blood Packed cells Plasma Platelet concentrates Other (state) ... 3. Transport of Blood Components 3.1 Does the institution collect blood through mobile donor clinic? 3.2 Does the institute distribute blood to other hospitals? 3.3 Does the institution have transport boxes in use? Yes No
How many teams involved? Volume handled per month? How many institutions? .. Volume handled per month? No. with capacity: <4 .. No. with capacity: 5 to 10 No. with capacity: 11 to 20 No. with capacity: >21 .. Shortest hrs Longest hrs ...
3.4 Time taken to deliver a transport box to another institution? 3.5 Temperature monitoring devices used in transport boxes? 3.6 Type of blood transport box in use. 1. Picnic/camper type of box 2. A locally constructed box
Material used in construction (if known) 3. If a blood transport box what International Standard(s) does it conform to? 3.7 Type of coolants (cooling devices) used to keep temperature low 1. Ice packs 2. Commercial coolants 3. Others, please state
Yes No
4. Quality management of the Blood Cold Chain 4.1 Does the institute have a Standard Operating Procedure for preventive maintenance of the equipment? 4.2 Does the Institution have a Standard Operating Procedure for monitoring temperature of the equipment? 4.3 Are staff regularly trained according to the SOP in place? 5. Equipment Maintenance 5.1 Who carries out preventive maintenance? Technical staff of the blood bank or other (state) 5.2 Are spare parts for blood cold chain equipment kept on site or centrally controlled? Locally available Centrally coordinated 5.3 Common problems experienced in the last 12 months:
(NB. Please state as an approximate percentage of all faults reported in the same period)
Fault 1. 2. 3. 4. 5. 6. 7. 8. 9. Compressor fault Refrigerant gas leakage Corrosion of equipment Faulty internal circulation fan Defective door sealer/lining Faulty temperature monitors Faulty switches Ice built up Faulty thermostat % % % % % % % % % Cost of repairs ($)
58
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
Environmental and human health concerns about the depletion of the ozone layer in the earths atmosphere have led to a global effort to phase out the production and consumption of CFCs. Until 1995, two major CFCs R11 and R12 were commonly used as refrigerants in compression refrigeration circuits, and as foaming agents for the insulation of refrigerators, freezers and insulated containers (cold boxes and vaccines carriers).
ANNEX 2
WHO Policy
WHO/BCT fully supports the recommendations of the Montreal Protocol and therefore recommends the following: 1. Countries should know that the continued use of CFC equipment after 2010 is not in conformity with the Montreal Protocol, and are urged to stop purchasing equipment using CFCs forthwith. 2. Managers of national blood programmes are urged to purchase blood cold chain equipment that meets WHO minimum performance specifications for the safe storage of blood components. WHO will shortly publish such information. 3. Manufacturers in developing countries are encouraged to switch to CFC-free production as soon as possible. 4. The maintenance staff of the Ministry of Health will require retraining on CFC-free equipment, if this has not already been done under the vaccine cold chain programme. The Ministry of Health or the WHO country office has more information on the training courses available. 5. There is need to adopt a systematic and coordinated plan to replace CFC equipment within the blood transfusion service or Ministry of Health. The policy has to be supported by a budget line that covers equipment procurement and a maintenance plan.
59
More detailed information on the Montreal Protocol and ozone layer depletion, replacements for ozone-depleting substances and suppliers of alternative technologies can be obtained from: UNEP DTIE OzonAction Programme, Tor Mirabeau, 3943, quai Andre Citroen, 75739 Paris Cedex 15, France. Tel: +33 (1) 44 37 14 50. Fax: +33 (1) 44 37 14 74. E-mail: [email protected] Internet: www.uneptie.org/ozonaction.html
6. This will be a good opportunity to develop a proper equipment inventory and maintenance plan not only for the blood cold chain equipment but also for other blood bank equipment. In view of the foregoing there is evident need to assess the extent to which blood storage refrigerators and plasma freezers need to be replaced in a given country. Annex 1 will assist countries in the development of a plan for the replacement of the equipment in line with the Montreal Protocol.
1. Are tools locally available for the repair of CFC-free equipment and have cold chain technicians been trained? 2. When the equipment arrives in the country: Check that the compressors are marked with a 100 mm blue disk that helps draw the attention of repair technicians. Check that blood cold boxes are marked with the recommended WHO emblem. Keep an inventory of where the CFC-free appliances are installed. To the extent possible, phase in the introduction of CFC-free equipment region by region or district by district in order to facilitate the repairs and service if required.
60
BLOOD COLD CHAIN: GUIDE TO THE SELECTION AND PROCUREMENT OF EQUIPMENT AND ACCESSORIES
ANNEX 3
01 Product Number assigned by WHO 01/ Product Number assigned by WHO 1 Capacity (see also Table 8, p53) 1 = < 4 blood bags 2 = 510 bags 3 = 1120 bags 4 = > 20 bags
61
Some key factors to consider when procuring blood cold chain equipment
Blood cold chain equipment must meet international standards, WHO minimum performance specifications and be correctly used and maintained by all personnel involved. Cold chain equipment must be reviewed carefully, bearing in mind the possibility of relocation of some equipment to meet needs. The design and quality of equipment should be carefully assessed so that it meets the needs of the laboratory and the users. Assess the performance history of the equipment and market reports before making a decision. Domestic refrigerators are NOT suitable for the storage of blood. The need for a degree of standardization should be taken into account when procuring equipment as it assists in staff training and equipment maintenance. The equipment should be ordered following agreed procedures. The availability of back-up support, spare parts and maintenance services are important considerations in the selection of cold chain equipment. Training for users and technicians must be taken into consideration before selecting any blood cold chain equipment.
ISBN 92 4 154579 8
Department of Blood Safety and Clinical Technology World Health Organization 1211 Geneva 27, Switzerland Fax: +41 22 791 4836 E-mail: [email protected] www.who.int/bct/