Nikon NPL-602 Series Instruction Manual
Nikon NPL-602 Series Instruction Manual
Instruction Manual
Contact Information Trimble Navigation Limited Engineering and Construction Division 5475 Kellenburger Road Dayton, Ohio 45424-1099 USA 800-538-7800 (toll free in USA) +1-937-245-5600 Phone +1-937-233-9004 Fax
www.trimble.com
Copyright and Trademarks 2006, Nikon-Trimble Co. Limited. All rights reserved. Microsoft, Windows, and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All trademarks are the property of their respective owners. It is prohibited to alter this manual in part or whole without express permission. The contents of this manual are subject to change without notice. Although every effort has been made to ensure the accuracy of this manual, please contact your dealer if you find anything in it that is incorrect or unclear. Release Notice This is the May 2006 release (revision A) of the Field Station NPL-632 Instruction Manual. It applies to software release version 1.10 for the field station NPL-632. Notices USA FCC 15B Class B satisfied. This equipment has been tested and found to comply with the limits for a Class B personal computer and peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Warning This equipment has been certified to comply with the limits for a Class B personal computer and peripherals, pursuant to Subpart B of Part 15 of FCC Rules. Only peripherals (computer input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified personal computer and/or peripherals is likely to result in interference to radio and TV reception. The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
European Union EU EMC Directive satisfied. Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la Class B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Taiwan Battery recycling requirements The product contains a removable battery. Taiwanese regulations require that waste batteries are recycled. Notice to Our European Union Customers For product recycling instructions and more information, please go to: Recycling in Europe To recycle Trimble WEEE, call: +31 497 53 2430, and ask for the WEEE associate, or mail a request for recycling instructions to: Trimble Europe BV c/o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel, NL
www.trimble.com/environment/summary.html
Contents
Safety 11 Introduction . . . . . . Laser Safety. . . . . . Warnings and Cautions . Warnings . . . Cautions . . . 1 Introduction. . . . Welcome . . . . . . Parts of the Instrument Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 . . 12 . . 13 . . 13 . . 14 . . . . . . . . 1 2 3 5
. . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking and Packing the Instrument . . . . . . . . . . . . . . . . . . Unpacking . . . . . . . . . . . . . . . . . . . . . . . . Packing . . . . . . . . . . . . . . . . . . . . . . . . . . Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . Detaching and Re-Attaching the Battery Pack. . . . . . . . . . . . . . . . Using the CompactFlash (CF) Card . . . . . . . . . . . . . . . . . . . . Inserting a CF card into the card slot . . . . . . . . . . . . . . Removing a CF card from the card slot . . . . . . . . . . . . . Using the USB Memory Stick. . . . . . . . . . . . . . . . . . . . . . . Inserting the USB memory stick into the connector slot . . . . . . . Transferring files from the instrument to an office computer using USB Setting Up the Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . Centering Using the Optical Plummet . . . . . . . . . . . . . . . . . . . Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the Measurement Mode and Preparing the Target . . . . . . . . . . Measurement with a prism . . . . . . . . . . . . . . . . . . Measurement in Reflectorless mode . . . . . . . . . . . . . . Preparing the Reflector Sheet . . . . . . . . . . . . . . . . . . . . . . . Setting Up the Prism Reflector . . . . . . . . . . . . . . . . . . . . . . Adjusting the height of the tribrach adapter . . . . . . . . . . . . Changing the direction of the prism . . . . . . . . . . . . . . Setting the prism constant . . . . . . . . . . . . . . . . . . Setting the position of the target plate . . . . . . . . . . . . . . Carrying the Instrument Case . . . . . . . . . . . . . . . . . . . . . . . Face-1/Face-2 Measurements . . . . . . . . . . . . . . . . . . . . . . . Getting Started . . . . . . . . . . . Turning the Instrument On and Off . . . . Turning on the instrument . . . . Turning off the instrument . . . . Selecting a Language . . . . . . . . . . Changing Regional Configuration Pre-sets . Display and Key Functions . . . . . . . . Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 7 . . 8 . . 8 . . 8 . . 8 . . 10 . . 11 . . 12 . . 13 . . 13 . . 14 . . 14 . . 15 . . 15 . . 17 . . 17 . . 18 . . 18 . . 19 . . 21 . . 22 . . 22 . . 23 . . 23 . . 24 . . 24 . . 26 . . 27 . . 28 . . 28 . . 28 . . 29 . . 30 . . 31 . . 33
iii
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
Adjusting lighting and sound levels. . . . . . . . . . . . . . . . . . . . . [DSP] key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [MODE] key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [COD] key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [HOT] key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bubble indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . [LG] key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [USR] keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [DAT] key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . List Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inputting Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Entering a point name or number . . . . . . . . . . . . . . . . . . . . . . Entering a code . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced feature: Searching for a code by using the first character 49 Entering values in feet and inches . . . . . . . . . . . . . . . . . . . . . Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Creating a new job . . . . . . . . . . . . . . . . . . . . . . . . . . . Measuring Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sighting a prism reflector . . . . . . . . . . . . . . . . . . . . . . . . Measuring distances. . . . . . . . . . . . . . . . . . . . . . . . . . . Measurement settings . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. 35 . 36 . 37 . 38 . 39 . 41 . 42 . 42 . 43 . 44 . 44 . 44 . 48 . 50 . 51 . 51 . 52 . 52 . 53 . 53
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HA Reset and Angle Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the horizontal angle to 0 . . . . . . . . . . . . . . . . . . . . . . . Entering the horizontal angle . . . . . . . . . . . . . . . . . . . . . . . . Recording a foresight point after repeat angle measurement . . . . . . . . . . . . Face-1/Face-2 measurement . . . . . . . . . . . . . . . . . . . . . . . . . Horizontal angle hold . . . . . . . . . . . . . . . . . . . . . . . . . . . Station Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting up a station with known coordinates or azimuth . . . . . . . . . . . . . . Advanced feature: Measuring F1 and F2 60 Setting up a station using multiple point resection . . . . . . . . . . . . . . . . Advanced feature: Viewing and deleting a measurement in resection 64 Setting up the station quickly without coordinates . . . . . . . . . . . . . . . . Determining station elevation . . . . . . . . . . . . . . . . . . . . . . . . Checking and resetting the backsight direction . . . . . . . . . . . . . . . . . Two-point resection along a known line . . . . . . . . . . . . . . . . . . . . Stakeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifying the stakeout point by angle and distance . . . . . . . . . . . . . . . Specifying the stakeout point by coordinates . . . . . . . . . . . . . . . . . . Advanced feature: Specifying a stakeout list by range input 73 DivLine S-O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RefLine S-O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Measuring distance and offset values along a specified line . . . . . . . . . . . . Measuring distance and offset values on the arc-curve . . . . . . . . . . . . . . Remote distance measurement. . . . . . . . . . . . . . . . . . . . . . . .
. . 55 . . 56 . . 56 . . 56 . . 56 . . 57 . . 58 . . 58 . . 58 . . . . . . . . . 61 . 64 . 65 . 66 . 67 . 69 . 69 . 71
. . 73 . . 74 . . 76 . . 76 . . 78 . . 80
iv
Contents
Measuring remote elevation . . . . . . . . . . . . . Measuring distance and offset values on the vertical plane . Measuring distance and offset values on the slope . . . . Recording Measurement Data. . . . . . . . . . . . . . . . . Recording data from any observation screen . . . . . . Outputting data to the COM port . . . . . . . . . . . Measuring Offsets . . . . . . . . . . . . . . . . . . . . . . Measuring taped offsets . . . . . . . . . . . . . . Measuring angle offsets . . . . . . . . . . . . . . Two-prism pole . . . . . . . . . . . . . . . . . Extending a line by horizontal angle offset . . . . . . . Entering a horizontal distance after an angle-only shot . . Calculating a corner point . . . . . . . . . . . . . Measuring circle offsets . . . . . . . . . . . . . . Extending the slope distance. . . . . . . . . . . . . 5
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. 82 . 83 . 85 . 86 . 86 . 87 . 88 . 88 . 89 . 89 . 90 . 92 . 92 . 94 . 95
Menu Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Job Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening an existing job . . . . . . . . . . . . . . . . . . . . Creating a new job . . . . . . . . . . . . . . . . . . . . . . Deleting a job . . . . . . . . . . . . . . . . . . . . . . . . Setting the control job . . . . . . . . . . . . . . . . . . . . . Displaying job Information . . . . . . . . . . . . . . . . . . . Importing a job. . . . . . . . . . . . . . . . . . . . . . . . Exporting a job. . . . . . . . . . . . . . . . . . . . . . . . Cogo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calculating angle and distance between two coordinates . . . . . . . Calculating and manually inputting coordinates . . . . . . . . . . . Calculating area and perimeter . . . . . . . . . . . . . . . . . Advanced feature: Entering a range of points 109 Calculating coordinates from line and offset . . . . . . . . . . . . Calculating coordinates using intersection functions . . . . . . . . . Advanced feature: Entering angle and distance offsets 115 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . Distance . . . . . . . . . . . . . . . . . . . . . . . . . . Coordinate . . . . . . . . . . . . . . . . . . . . . . . . . Power saving. . . . . . . . . . . . . . . . . . . . . . . . . Communications . . . . . . . . . . . . . . . . . . . . . . . Stakeout. . . . . . . . . . . . . . . . . . . . . . . . . . . Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recording. . . . . . . . . . . . . . . . . . . . . . . . . . Others settings . . . . . . . . . . . . . . . . . . . . . . . . Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing records . . . . . . . . . . . . . . . . . . . . . . . Deleting records . . . . . . . . . . . . . . . . . . . . . . . Editing records . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 110 . . . . . . . 111 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 116 116 118 118 118 118 119 120 120 121 121 125 126
Contents
Searching records . . . . . . . . . . . . . . . . . . . . . . Entering coordinates . . . . . . . . . . . . . . . . . . . . Point name list and code list . . . . . . . . . . . . . . . . . . Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Downloading data . . . . . . . . . . . . . . . . . . . . . . Uploading coordinate data . . . . . . . . . . . . . . . . . . Advanced feature: Editing the data order for upload 137 Uploading a point name list or code list . . . . . . . . . . . . . 1sec-Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [MSR] key settings . . . . . . . . . . . . . . . . . . . . . . [DSP] key settings . . . . . . . . . . . . . . . . . . . . . . [USR] key settings . . . . . . . . . . . . . . . . . . . . . . [S-O] key settings . . . . . . . . . . . . . . . . . . . . . . [DAT] key settings . . . . . . . . . . . . . . . . . . . . . . Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removable Memory (External Memory) . . . . . . . . . . . . . . . . . . Displaying the external memory files . . . . . . . . . . . . . . Renaming a job or file on the removable memory . . . . . . . . . Deleting a job of file from the removable memory . . . . . . . . . Coping a job from the removable device. . . . . . . . . . . . . Changing the list view of files on the removable memory . . . . . . 6 Checking and Adjustment . . . . . . . . . . . . . . . . . . . . Checking and Adjusting the Plate Level . . . . . . . . . . . . . . . . . . Checking and Adjusting the Circular Level. . . . . . . . . . . . . . . . . Checking and Adjusting the Optical Plummet. . . . . . . . . . . . . . . . Zero Point Errors of Vertical Scale and Horizontal Angle Corrections . . . . . Checking . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Instrument Constant . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . Main Body . . . . . . . . . . . . . . . Telescope . . . . . . . . . . . EDM. . . . . . . . . . . . . Dual-axis tilt sensor . . . . . . . Angle measurement . . . . . . . Precision . . . . . . . . . . . Measurement intervals . . . . . . Lumi-guide . . . . . . . . . . Clamps/tangent screws . . . . . . Tribrach. . . . . . . . . . . . Level vial sensitivity . . . . . . Optical plummet . . . . . . . . Display and keypad . . . . . . . Connections in the base of instrument Battery pack BC-80 . . . . . . . Environmental performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
129 131 132 135 135 136 138 138 138 139 139 140 140 140 141 142 142 142 143 144 144
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. 145 . 146 . 146 . 147 . 148 . 148 . 148 . 152 . 155 . 156 . 156 . 156 . 157 . 157 . 157 . 158 . 158 . 158 . 158 . 158 . 158 . 159 . 159 . 159 . 159
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
Contents
Dimensions . . . . Weight . . . . . . CompactFlash card . USB Connecters . . Standard Components . . . External Device Connector . 8 9
. . . . . .
. . . . . .
. . . . . . . . . .
. . . .
. . . . . . . . . . . .
. . . . . .
. . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . . . . . .
. . . .
. . . . . . . . . . . .
. . . . . .
. . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . .
. . . . . .
. . . . . .
System Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Communications . . . . . . . . . . Uploading Coordinate Data . . . . . . . . Settings . . . . . . . . . . . . Record format . . . . . . . . . Uploading Point Lists and Code Lists . . . Settings . . . . . . . . . . . . File format . . . . . . . . . . Downloading Data . . . . . . . . . . . . Settings . . . . . . . . . . . . Nikon raw record formats . . . . SDR2x and SDR33 record formats . Data examples . . . . . . . . . Error Messages . . . . . . Angle . . . . . . . . . . . . . Cogo . . . . . . . . . . . . . Communications . . . . . . . Data . . . . . . . . . . . . . Job Manager . . . . . . . . . Programs . . . . . . . . . . . Recording Data . . . . . . . . Searching . . . . . . . . . . . Settings. . . . . . . . . . . . Stakeout . . . . . . . . . . . Station Setup . . . . . . . . . Removable Memory Devices . . System Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 . 168 . 168 . 168 . 170 . 170 . 170 . 172 . 172 . 172 . 175 . 179 . 183 . 184 . 184 . 184 . 185 . 186 . 186 . 187 . 188 . 188 . 188 . 189 . 190 . 191
10
vii
Contents
viii
Safety
In this chapter:
Q Q Q
11
Safety
Introduction
For your safety, read this instruction manual carefully and thoroughly before using the NPL-632 instrument. Although Nikon products are designed for maximum safety, using them incorrectly or disregarding the instructions can cause personal injury or property damage. Also read the instruction manual for the battery charger, and the documentation for any other equipment that you use with a NPL-632 instrument. Note Always keep the manual near the instrument for easy reference.
Laser Safety
The NPL-632 is a Class 1 laser instrument. Class 1 laser instruments do not require any special precautions, signage, or training for laser safety.
WARNING The laser beam is hazardous to the eyes and the body. Do not sight the instrument on the face or body of a person. Table 1.1
Wave length Drive method Output power Pulse width
Table 1.2
Wave length
Drive method
Table 1.3
E.U. U.S.A.
Safety class
EN60825-1/Am.2:2001 (IEC60825-1/Am.2:2001), class 1 FDA21CFR, Part 1040, Sections 1040.10 and 1040.11 (except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001), class 1
12
Safety
C C
WARNING Warnings alert you to situations that could cause death or serious injury.
CAUTION Cautions alert you to situations that could cause injury or property damage.
Warnings
Before using the instrument, read the following warnings and follow the instructions that they provide:
C C C C C C C
WARNING Never look at the sun through the telescope. If you do, you may damage or lose your eyesight.
WARNING The NPL-632 instrument is not designed to be explosion-proof. Do not use the instrument in coal mines, in areas contaminated with coal dust, or near other flammable substances.
WARNING The NPL-632 total station is a Class 1 laser instrument. The laser beam is hazardous to the eyes and the body. Do not sight the instrument on the face or body of a person. If you suspect an injury caused by exposure to the laser beam, seek medical advice immediately. If the instrument housing is open and the instrument is turned on, the laser emits a beam stronger than the Class 1 safety level.
WARNING Never disassemble, modify, or repair the instrument yourself. If you do, you may receive electric shocks or burns, or the instrument may catch fire. You may also impair the accuracy of the instrument.
WARNING Use ONLY the battery charger that is attached to the instrument to charge the battery pack (P/N BC-80). Do NOT use any chargers other than the enclosed model. Using other chargers may cause the battery pack to catch fire or rupture. You cannot use the old Nikon chargers, models Q7U/E or Q-7C, to charge the BC-80.
WARNING Do not cover the battery charger while the battery pack is being recharged. The charger must be able to dissipate heat adequately. Coverings such as blankets or clothing can cause the charger to overheat.
WARNING Avoid recharging the battery pack in humid or dusty places, in direct sunlight, or near heat sources. Do not recharge the battery pack when it is wet. If you do, you may receive electric shocks or burns, or the battery pack may overheat or catch fire.
13
Safety
C C C
Cautions
WARNING Although the battery pack (P/N BC-80) has an auto-reset circuit breaker, you should take care not to short circuit the contacts. Short circuits can cause the battery pack to catch fire or burn you.
WARNING Never burn or heat the battery. Doing so may cause the battery to leak or rupture. A leaking or ruptured battery can cause serious injury.
WARNING Before storing the battery pack or battery charger, cover the contact points with insulation tape. If you do not cover the contact points, the battery pack or charger may short circuit, causing fire, burns, or damage to the instrument.
Before using the instrument, read the following cautions and follow the instructions that they provide:
C C C C C C C
CAUTION Use of controls, adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure.
CAUTION The tips of the tripod ferrules are very sharp. When handling or carrying the tripod, take care to avoid injuring yourself on the ferrules.
CAUTION Although a Class 1 laser is regarded as safe under normal operating conditions, it is recommended that you cap the objective when the instrument is not in use in order to avoid laser emissions. Do NOT look into the laser.
CAUTION Before carrying the tripod or the instrument in the carrying case, check the shoulder strap and its clasp. If the strap is damaged or the clasp is not securely fastened, the carrying case may fall, causing personal injury or instrument damage.
CAUTION Before setting up the tripod, make sure that no-ones hands or feet are underneath it. When the legs of the tripod are being driven into the ground, they could pierce hands or feet.
CAUTION After mounting the instrument on the tripod, securely fasten the thumb screws on the tripod legs. If the thumb screws are not securely fastened, the tripod may collapse, causing personal injury or instrument damage.
CAUTION After mounting the instrument on the tripod, securely fasten the clamp screw on the tripod. If the clamp screw is not securely fastened, the instrument may fall off the tripod, causing personal injury or instrument damage.
14
Safety
C C C
CAUTION Securely fasten the tribrach clamp knob. If the knob is not securely fastened, the tribrach may come loose or fall off when you lift the instrument, causing personal injury or instrument damage.
CAUTION Before you pick up the instrument by the carrying handle, make sure that the battery pack is clamped securely in place, and that the battery mounting buttons are set in the vertical (LOCK) position. If the battery pack is not securely fastened, the main unit may come loose or fall off when you lift the instrument, causing personal injury or instrument damage.
CAUTION Do not stack objects on the plastic carrying case, or use it as a stool. The plastic carrying case is unstable and its surface is slippery. Stacking objects on the carrying case or sitting on it may cause personal injury or instrument damage.
15
Safety
16
CHAPTER
1
Introduction
In this chapter:
Q Q Q
1
Introduction
Welcome
Thank you for purchasing this Nikon product. This instruction manual was written for the users of a Field Station NPL-632 instrument. Before you operate a NPL-632 instrument, read this manual carefully. In particular, pay attention to the warnings and cautions that appear in the Safety section at the front of the manual. Before you begin, you should also read the maintenance instructions. For more information, see Maintenance, page 5.
Introduction
Battery mounting buttons Optical sight (finder) Telescope focusing ring Main body/battery aligning mark
Telescope eyepiece Diopter ring Reticle plate cover Plate level Display and face-1 keyboard
Vertical clamp
Storage mark The laser Safety Label shown is attached to the underside of the keyboard
Figure 1.1
Introduction
Optical plummet Display and face-2 keyboard Data output/ external power input connector (Input voltage 7.211 V DC)
Tribrach
Circular level
Base plate
Leveling screw
Figure 1.2
Introduction
USB A-connector (for USB memory) USB B-connector (for ActiveSync technology)
Figure 1.3
Maintenance
Before using the instrument, read and follow the following maintenance instructions: Do not leave the instrument in direct sunlight or in a closed vehicle for prolonged periods. Overheating the instrument may reduce its efficiency. If the NPL-632 instrument has been used in wet conditions, immediately wipe off any moisture and dry the instrument completely before returning the instrument to the carrying case. The instrument contains sensitive electronic assemblies which have been well protected against dust and moisture. However, if dust or moisture gets into the instrument, severe damage could result. In the field, make sure that the cap and cover are firmly closed. If you open the connector cap and/or the card slot cover in the field you cannot ensure the required waterproof and dust-proof standards (IP 54). Before you open the connector cap or the card slot cover, wipe off all moisture. If you open the cap/cover while it is wet, it might result in malfunction. Sudden changes in temperature may cloud the lenses and drastically reduce the measurable distance, or cause an electrical system failure. If there has been a sudden change in temperature, leave the instrument in a closed carrying case in a warm location until the instrument returns to room temperature.
Introduction
Do not store the NPL-632 instrument in hot or humid locations. In particular, you must store the battery pack in a dry location at a temperature of less than 30 C (86 F). High temperature or excessive humidity can cause mold to grow on the lenses. It can also cause the electronic assemblies to deteriorate, and so lead to instrument failure. Store the battery pack with the battery discharged. When storing the instrument in areas subject to extremely low temperatures, leave the carrying case open. Do not overtighten any of the clamp screws. When adjusting the vertical tangent screws, upper plate tangent screws, or leveling screws, stay as close as possible to the center of each screws range. The center is indicated by a line on the screw. For final adjustment of tangent screws, rotate the screw clockwise. If the tribrach will not be used for an extended period, lock down the tribrach clamp knob and tighten its safety screw. Do not use organic solvents (such as ether or paint thinner) to clean the non-metallic parts of the instrument (such as the keyboard) or the painted or printed surfaces. Doing so could result in discoloration of the surface, or in peeling of printed characters. Clean these parts only with a soft cloth or a tissue, lightly moistened with water or a mild detergent. To clean the optical lenses, lightly wipe them with a soft cloth or a lens tissue that is moistened with alcohol. The reticle plate cover has been correctly mounted. Do not release it or subject it to excessive force to make it watertight. Press the cap that covers the data output/external power input connector terminal until it clicks into place. The instrument is not watertight if the cap is not attached securely, or when the data output/external power input connector is used. The carrying case is designed to be watertight, but Reticle plate cover you should not leave it exposed to rain for an extended period. If exposure to rain is unavoidable, make sure that the carrying case is placed with the Nikon nameplate facing upward. The BC-80 battery pack contains a Ni-MH battery. When disposing of the battery pack, follow the laws or rules of your municipal waste system. The instrument can be damaged by static electricity from the human body discharged through the data output/external power input connector. Before handling the instrument, touch any other conductive material once to remove static electricity.
CHAPTER
2
Preparation
In this chapter:
Q Q Q Q Q Q Q Q Q Q Q Q Q Q
2
Unpacking and Packing the Instrument Charging the Battery Pack Detaching and Re-Attaching the Battery Pack Using the CompactFlash (CF) Card Using the USB Memory Stick Setting Up the Tripod Centering Using the Optical Plummet Leveling Sighting Setting the Measurement Mode and Preparing the Target Preparing the Reflector Sheet Setting Up the Prism Reflector Carrying the Instrument Case Face-1/Face-2 Measurements
Preparation
Unpacking
To unpack the instrument, grip the carrying handle and gently remove the instrument from the carrying case.
Packing
Note Store the instrument with the battery pack attached. To pack the instrument into the carrying case: 1. 2. Set the telescope in the horizontal face-1 position. Align the O storage mark on the bottom of the face-1 keyboard with W the mark on the tribrach clamp knob. Lightly fasten the clamp knobs. Place the instrument in the carrying case.
3. 4.
C C C
8
WARNING Use ONLY the battery charger that is attached to the instrument to charge the battery pack (P/N BC-80). Do NOT use any chargers other than the enclosed model. Using other chargers may cause the battery pack to catch fire or rupture. You cannot use the old Nikon chargers, models Q7U/E or Q-7C, to charge the BC-80 battery pack.
WARNING Do not cover the battery charger while the battery pack is being recharged. The charger must be able to dissipate heat adequately. Coverings such as blankets or clothing can cause the charger to overheat.
WARNING Avoid recharging the battery pack in humid or dusty places, in direct sunlight, or near heat sources. Do not recharge the battery pack when it is wet. If you do, you may receive electric shocks or burns, or the battery pack may overheat or catch fire.
Preparation
C C C
WARNING Although the battery pack (P/N BC-80) has an auto-reset circuit breaker, you should take care not to short circuit the contacts. Short circuits can cause the battery pack to catch fire or burn you.
WARNING Never burn or heat the battery. Doing so may cause the battery to leak or rupture. A leaking or ruptured battery can cause serious injury.
WARNING Before storing the battery pack or battery charger, cover the contact points with insulation tape. If you do not cover the contact points, the battery pack or charger may short circuit, causing fire, burns, or damage to the instrument.
Important notes
Charge the battery pack indoors when the ambient temperature is between 10 C and 40 C (between 50 F and 104 F). If you try to charge the battery when the ambient temperature is outside this range, the protective circuit will activate and prevent it from being charged normally. After charging the battery pack, do not recharge it until it has been fully discharged. Recharging a fully charged battery pack lowers its performance. To prevent malfunction, keep the charging plug clean. If the charger indicator LED2 blinks orange and green after charging is started, there may be a problem in the battery pack. Do NOT use or charge the battery pack any further. Please contact your dealer. If the ambient temperature drops below 10 C (50 F) while the battery pack is charging, charging stops. When the ambient temperature rises above 10 C (50 F), charging resumes. If both the charger indicators LED1 and LED2 remain orange for more than three hours while the ambient temperature is in the normal range (10 C through 40 C or 50 F through 104 F), there may be a problem with the battery pack. Do NOT use or charge the battery pack any further. Please contact your dealer. During the charge, the battery pack and charger will become warm. This is normal. If the battery pack is used at temperatures below -20 C (-4 F), the battery capacity will be reduced and result in less operation time than if the battery pack is used at room temperature. If a battery pack is not used for a long period, it can never be charged to its full capacity again.
Preparation
Charging the battery pack 1. 2. Connect the power plug on the charger to an AC power outlet. Connect the charging plug on the charger cable to the charging connector on the battery pack. Both indicators LED1 and LED2 on the charger light up orange and charging starts automatically. When the battery pack is fully charged, LED2 changes to green.
LED1 LED1
LED2 LED2
1. 2.
If the instrument is turned on, press [PWR] to turn it off. Set the battery mounting buttons in the horizontal (UNLOCK) position. To do this, turn each button inward. While pressing both battery mounting buttons, lift the battery pack off the main body of the instrument.
3.
CAUTION Before you pick up the instrument by the carrying handle, make sure that the battery pack is clamped securely in place, and that the battery mounting buttons are set in the vertical (LOCK) position. If the battery pack is not securely fastened, the main unit may come loose or fall off when you lift the instrument, causing personal injury or instrument damage.
10
Preparation
1. 2.
Make sure that the battery mounting buttons are in the horizontal (UNLOCK) position. Align the O mark on the right battery mounting button with the O mark on the main body of the instrument. While pressing the battery mounting buttons, lower the battery pack onto the connecting pins on the top of the instrument. When the battery pack is in position, release the battery mounting buttons. Set the battery mounting buttons in the vertical (LOCK) position to lock the battery pack into place. To do this, turn the mounting buttons outward. When the battery pack is correctly mounted and locked, there is a slight gap between the battery pack and the main body of the instrument. This is a normal part of the instruments design.
3.
4.
5.
LOCK position
Note An external battery is available as an optional accessory for the NPL-632 instrument. When the external battery is connected and the BC-80 battery pack is mounted on the instrument, the instrument automatically uses the power source that has the most available power.
C C C
CAUTION To ensure that the instrument and card remains waterproof and dust-proof, close the cover and lock it firmly.
CAUTION Before you open the card slot cover, wipe off all moisture. If you open the cap or cover while they are wet, it may result in malfunction.
CAUTION While the system is writing data to the CF card or deleting data in the CF card, do not carry out the following actions as this may result in data corruption or card malfunction: - Remove the CF card - Remove the battery pack - Turn off the instrument
11
Preparation
C C
CAUTION Before removing the CF card from the instrument, turn off the instrument. If you remove the card while the instrument is ON, it might result in card malfunction.
CAUTION Nikon recommends that you use the authorized CF card (P/N HXA20657). Although it may be possible to use other CF cards, the performance and reliability are unknown and cannot be guaranteed.
Note Do NOT rotate the knob on the slot cover beyond the limit as this may damage the knob.
2.
Place the CF card with its blank side facing outward, and with the connector-side facing down, and then insert the card into the slot.
CF card Connector
Note Make sure that you place the card correctly in relation to the slot before you push the card into the slot. If the card is not placed correctly and you then push it too hard in the wrong direction it may malfunction.
Card slot
3.
Make sure that the protrusion on the knob is set to the OPEN (vertical) position and then close the cover.
Open position Lock position
12
Preparation
CAUTION If you force the cover closed when the protrusion on the knob cover is set to the LOCK (horizontal) position, you may damage the cover.
4.
Rotate the knob counter-clockwise until the protrusion on the knob in set to the LOCK position.
Note To ensure that the cover is firmly locked, the cover remains slightly open if you do not rotate the knob correctly so that the protrusion points to the LOCK position. Make sure that the cover is firmly closed.
2.
C C C
CAUTION Before you open the card slot cover, wipe off all moisture. If you open the cap or cover while they are wet, it may result in malfunction.
CAUTION Nikon recommends that you format the USB memory stick on your office computer before you use it for the first time.
CAUTION While the system is writing data to the USB memory or deleting data in the USB memory, do NOT carry out the following actions as this may result in data corruption or card malfunction: - Remove the USB memory stick - Remove the battery pack - Turn off the instrument
C C
CAUTION Before removing the USB memory stick from the instrument, turn off the instrument. If you remove the USB memory while the instrument is ON, it may result in memory malfunction.
CAUTION Do not place too much stress on the USB memory stick.
13
Preparation
C C C
CAUTION When you use or store the USB memory stick, avoid heat, moisture, and direct sunlight.
CAUTION Do not attempt to close the card slot cover with a USB memory stick still in the instrument.
Note Do NOT rotate the knob on the slot cover beyond the limit as this may damage the knob. 2. Check the shape of the USB connector and insert it correctly into the instrument. See USB Connecters, page 160.
Note Carefully support the instrument when you insert/remove the USB memory stick to/from the instrument. 3. Make sure that the protrusion on the knob is set to the OPEN (vertical) position and then close the cover.
CAUTION If you force the cover closed with the protrusion on the knob cover set to the LOCK (horizontal) position, you may damage the cover.
4.
Rotate the knob counter-clockwise until the protrusion on the knob in set to the LOCK position.
Note To ensure that the cover is firmly locked, the cover remains slightly open if you do not rotate the knob correctly so that the protrusion points to the LOCK position. Make sure that the cover is firmly closed.
Export files from your office computer to the instrument. Import recorded job files from the instrument to your office computer.
To connect the USB memory stick to the office computer using the connecting cable:
14
Preparation
1. 2. 3.
Insert the large connector of the connecting cable into the correct slot on your computer. Open the slot cover of the instrument. See Inserting a CF card into the card slot, page 12, Step 1. Insert the smaller connector of the connecting cable into the USB-B connector slot on the instrument. See USB Connecters, page 160.
On your office computer, you can now browse to the Mobile Device from where you can view, copy, or move job files between the office computer and the instrument. Note Before you can use the ActiveSync technology, you need to install the USB driver software. Download the driver software from the Drivers folder on the CD-ROM provided with the instrument.
CAUTION The tips of the tripod ferrules are very sharp. When handling or carrying the tripod, take care to avoid injuring yourself on the ferrules.
Note Do not carry the instrument while it is attached to a tripod. 1. 2. 3. 4. Open the tripod legs enough to for the instrument to be stable. Locate the tripod directly over the station point. To check the tripods position, look through the center hole in the tripod head. Firmly press the tripod ferrules into the ground. Level the top surface of the tripod head.
Note If you want to use the plumb bob to center the instrument (see Centering Using the Optical Plummet, page 15), you must level the tripod head precisely. 5. 6. 7. 8. Securely fasten the thumb screws on the tripod legs. Place the instrument on the tripod head. Insert the tripod mounting screw into the center hole of the base plate of the instrument. Tighten the tripod mounting screw.
15
Preparation
To center the instrument using the optical plummet: 1. 2. Set up the instrument on the tripod. For detailed instructions, see Setting Up the Tripod, page 15. While looking through the optical plummet, align the reticle with the station point. To do this, turn the leveling screws until the center mark of the reticle is directly over the image of the station point. While supporting the tripod head with one hand, loosen the tripod leg clamps and adjust the lengths of the legs until the air bubble is in the center of the circular level. Tighten the tripod leg clamps. Use the plate level to level the instrument. For detailed instructions, see Leveling, page 17. Look through the optical plummet to check that the image of the station point is still in the center of the reticle mark. If the station point is off center, do one of the following:
3.
4. 5. 6. 7.
If the station point is slightly off center, loosen the tripod mounting screw and then center the instrument on the tripod. Use only direct movement to center the instrument. Do not rotate it. When the instrument is centered, tighten the mounting screw.
If the displacement of the station point is major, repeat this procedure from Step 2.
16
Preparation
Leveling
When you level the instrument, you make the vertical axis of the instrument exactly vertical. To level the instrument, use the plate level. To level the instrument: 1. 2. Loosen the upper plate clamp. Rotate the alidade until the plate level is parallel with any two of the leveling screws (B and C). Use leveling screws B and C to move the bubble into the center of the level. Rotate the alidade approximately 90.
1 B
3. 4.
5. 6. 7. 8.
Use leveling screw A to move the bubble into the center of the level. Repeat Step 1 through Step 5 to center the bubble in both positions.
B A
Rotate the alidade 180. If the bubble in the plate level remains 2 centered, the instrument is level. If the bubble moves off center, adjust the plate level. For detailed instructions, see Checking and Adjusting the Plate Level, page 146.
Sighting
When you sight the instrument, you aim the telescope at the target, bring the target image into focus, and align the image with the center crosshairs of the reticle. To sight the instrument: 1. Adjust the diopter: a. Aim the telescope at a blank area, such as the sky or a piece of paper.
WARNING Never look at the sun through the telescope. If you do, you may damage or lose your eyesight.
17
Preparation
b.
Looking through the eyepiece, rotate the diopter ring until the reticle crosshairs are in sharp focus. Aim the telescope at the target image. Rotate the focusing ring until the target image is in sharp focus on the reticle crosshairs. Move your eye vertically and laterally to check whether the target image moves relative to the reticle crosshairs.
Diopter ring Telescope focusing ring
2.
Eliminate parallax: a. b.
c.
If the target image does not move, there is no parallax. d. 3. If the target image does move, rotate the telescope focusing ring. Then repeat from Step c. The final turn of the tangent screw should be in a clockwise direction, to align the target accurately on the center crosshairs.
In some cases, you can measure another target that is not appropriate to the set measurement mode.
18
Preparation
Do not use a prism with scratches, a dirty surface, or a chipped center. Prisms with thin edges are recommended.
thin edges
chipped center
thick edges
When using a reflector sheet, take measurements longer than 5 meters. When using a mini or standard prism, take measurements longer than 10 meters. When measuring a short distance, incline the prism slightly so that the EDM can ignore unnecessary reflections on the prism surface, as shown below.
Hold the prism securely in place and do not move while taking measurements. In Prism mode, in order to avoid false measurements on objects other than the prism or reflector-sheet, targets that are less reflective than the prism or reflector sheet are not measured. Even if you start a measurement, measured values are not displayed. To measure less reflective objects, use the N-prism (reflectorless) mode.
Measurable distances may be shorter or measurement intervals may be longer in the following cases:
19
Preparation
the angle of the laser against the target is small the surface of the target is wet
In direct sunlight, the measurable distance may be shorter. In this case, try to throw a shadow on the target. Targets with completely flat surfaces, such as mirrors, cannot be measured unless the beam and the target are perpendicular to each other.
Sighting a prism in Reflectorless mode may cause an excessive signal error. In this case, change the [MSR1] or [MSR2] key Target setting to Prism.
In the Reflectorless mode, the beam passing area is shown by a circle in crosshairs on the telescope reticle. If the target is smaller than the circle and there is something highly reflective in the background, the measured data may be affected by these adverse conditions.
When an obstacle momentarily passes through the beam between the instrument and the target (for example, passing cars on the road), the false data (short distance) is deleted automatically. However, if the amount of reflection is almost the same and the difference in distances between the correct and the false data is less than two meters, it may cause an error in measurements.
Make sure there are no obstacles between the instrument and the target when taking measurements. When you need to take measurements across a road or a place where vehicles or other objects are frequently moving, take several measurements to a target for the best result.
20
Preparation
Mini prism C
Tribrach
Nikon tripod
Figure 2.1
21
Preparation
2. 3. 4. 5.
Adjust the height of the tribrach adapter (see page 22). If necessary, change the direction of the prism (see page 23). Set the prism constant (see page 23). If you are using a single prism holder, set the position of the target plate (see page 24).
Detailed instructions for Step 2 through Step 5 are provided on the following pages.
22
Preparation
3.
3.
Tip -To use a triple prism holder as a single prism holder, attach the prism to the center thread of the prism holder.
2.
Set the prism constant. To do this, hold down [MSR1] or [MSR2] for one second. For more information, see Measurement settings, page 53.
Note The prism constant of a Nikon prism is always 0, whether it is attached to a single prism holder or a triple prism holder.
If your prism constant is not 0mm, then directly enter the prism constant value in the Const field. For example, if your prism constant is 30mm, enter 30mm in the Const field on the instrument.
23
Preparation
Tip When using a prism at a short distance, set the prism at a slight angle to the sighting axis rather than completely square.
If using a single prism, make sure that the target plate is aligned with the tribrach adapter and the prism. To set the position of the target plate: 1. 2. Use the two set screws supplied to attach the target plate to the single prism holder. Move the target plate within the screw holes until the apex of the wedge pattern is aligned with the vertical axis of the prism and the tribrach adapter.
Center on axis
To carry the case over your shoulder, attach one belt to the case on the side of handle.
To carry the case as a backpack, attach two belts to the case on the side that displays the Nikon sticker side.
Figure 2.3 on page 25 shows how to attach the belt to the instrument correctly.
24
Preparation
To ensure that the edge of the belt is enclosed properly: 1. 2. Set up the belt and parts attached to the belt for use as either a shoulderstrap or backpack straps, as described on page 24. Take the edge of the belt and insert it through the parts, in the order shown below.
Figure 2.3
25
Preparation
Face-1/Face-2 Measurements
You can take a measurement from either face of the instrument. To change the face, rotate the instrument 180 on its base, and rotate the telescope 180 within the standard. By averaging the Face-1 and Face-2 measurement values, you can cancel out most constant mechanical errors. Some errors, such as vertical axis error, cannot be cancelled out by averaging Face-1 and Face-2 measurements.
CAUTION When rotating the telescope, take care not to catch your finger in the gap between the instruments standard and the telescope.
A Face-1 measurement is made with the vertical circle positioned to the left of the telescope eyepiece. A Face-2 measurement is made with the vertical circle positioned to the right of the telescope eyepiece.
Face-1
Face-2
26
CHAPTER
3
Getting Started
In this chapter:
Q Q Q Q Q Q Q Q
3
Turning the Instrument On and Off Selecting a Language Changing Regional Configuration Pre-sets Display and Key Functions List Display Inputting Data Jobs Measuring Distances
27
Getting Started
2.
To change the temperature or pressure value, use [^] or [v] to move the cursor to the field that you want to change. Then press [ENT].
3. 4.
If you want to initialize the horizontal angle, rotate the alidade. Tilt the telescope until it passes the horizontal position on Face-1.
If you have entered your name or your companys name in the Owners detail field, the text from this field appears on the start-up screen. To set the Owners detail field, go to MENU > Settings > Other. For more information, see page 120.
Once you start to use an initialized HA, you must rotate the alidade to initialize the HA every time you turn on the instrument. If you do this, you can maintain a fixed HA orientation even if the instrument has moved while it is turned off. If you tilt the telescope before you rotate the alidade, the horizontal angle is not initialized, and the instrument uses the previous HA reading.
[ENT] again
the Reset softkey
28
Getting Started
To ... put the instrument into power-saving mode cancel the power-off process and return to the previous screen
[ESC]
If you press the Reset softkey, the software is rebooted and the Basic Measurement Screen (BMS) appears without an open job.
Sleep mode If you press the Sleep softkey in the Press [ENT] OFF screen, or enable the Power Save setting (see Power saving, page 118), the instrument goes into sleep mode. When the instrument is in sleep mode, it wakes up if any of the following occurs:
You press a key The instrument receives a remote control command You rotate the alidade You tilt the telescope
Selecting a Language
The NPL-632 instrument also supports Chinese. To select a different language: 1. Turn on the instrument and press [ESC] and [3] at the Tilt Telescope screen. The Select Language screen appears. The screen shows which languages are currently available on the instrument. The current language selection is highlighted. 2. Press [^] or [v] to highlight the required language and then press [ENT.] The instrument reboots and displays the start-up Tilt Telescope screen in the selected language.
29
Getting Started
The settings affected by the Regional Configuration screen are shown below:
Category Angle Setting VA zero Resolution HA corr. HA Distance Scale T-P corr. Sea Level C&R corr. Coordinates Order Label AZ zero Power Save Main Unit EDM Unit Sleep Communication Ext. Comm Baud Length Parity Stop bit Stakeout Add PT LG Dist Europe Zenith 1" (see note) On Azimuth 1.000000 On Off 0.132 ENZ ENZ North Off 3 minutes 5 minutes Nikon 4800 8 None 1 1000 1.00 feet (0.30m) International Zenith 1" (see note) On Azimuth 1.000000 On Off 0.132 ENZ ENZ North Off 3 minutes 5 minutes Nikon 4800 8 None 1 1000 1.00 feet (0.30m) United States Zenith 1" (see note) On Azimuth 1.000000 On Off 0.132 NEZ NEZ North Off 3 minutes 5 minutes Nikon 4800 8 None 1 1000 1.00 feet (0.30m)
30
Getting Started
Category Units
United States DEG US-ft F In Hg RAW&XYZ On Internal Fast None On No <ABC> Blank
Rec
Others
XYZ disp 2nd Unit Sig Beep Split ST CD Input Owners Detail
The default regional configuration pre-set is International settings. For more information, see Settings, page 115.
31
Getting Started
Key
Function
Details
Records measured data, moves on to the next screen, or confirms and page 86 accepts the entered data in input mode. You have the option to record the measurement as a CP record instead of an SS record, if you hold this key down for one second in the Basic Measurement Screen (BMS). The instrument outputs the current measurement data (PT, HA, VA, and SD) on the COM port if you press this key in the BMS or in a Stakeout observation screen. (The Data Rec settings must be set to COM.) Returns to the previous screen. In numeric or alphanumeric mode, deletes input.
Starts distance measurement, using the measure mode settings for the [MSR1] key. Displays measurement mode settings, if held down for one second. Starts distance measurement, using the measure mode settings for the [MSR2] key. Displays measurement mode settings, if held down for one second. Moves to the next available display screen. Changes the fields that appear on the DSP1, DSP2, and DSP3 screens, if held down for one second. Displays the Angle menu.
page 52
page 52
page 54
page 56
Displays the Station Setup menu. In numeric mode, enters 7. In alphanumeric mode, enters A, B, C, or 7.
page 58
Displays the Stakeout menu. page 69 Shows stakeout settings, if held down for one second. In numeric mode, enters 8. In alphanumeric mode, enters D, E, F, or 8. Displays the Offset Point Measurement menu. page 88 In numeric mode, enters 9. In alphanumeric mode, enters G, H, I, or 9. Displays the Programs menu, which contains additional measuring page 76 programs. In numeric mode, enters 4. In alphanumeric mode, enters J, K, L, or 4. Turns the Lumi-guide on or off. In numeric mode, enters 5. In alphanumeric mode, enters M, N, O, or 5. Displays RAW, XYZ, or STN data, depending on your setting. In numeric mode, enters 6. In alphanumeric mode, enters P, Q, R, or 6. page 42
page 43
32
Getting Started
Key
Function
Details
page 42 Executes the function that is assigned to the [USR1] key. In numeric mode, enters 1. In alphanumeric mode, enters S, T, U, or 1. Executes the function that is assigned to the [USR2] key. In numeric mode, enters 2. In alphanumeric mode, enters V, W, X, or 2. Opens a window where you can enter a code. The default code value page 38 is the last code entered. In numeric mode, enters 3. In alphanumeric mode, enters Y, Z, a space, or 3. Displays the (HOT) menu, which includes Height of Target, TempPress, Target, Note recording, and Default PT settings. In numeric mode, enters (minus). In alphanumeric mode, enters. (period), (minus), or + (plus). Displays the Bubble indicator. In numeric mode, enters 0. In alphanumeric mode, enters *, /, =, or 0. page 39
page 41
Status bar
The status bar appears on the right side of every screen. It contains icons that indicate the status of various system functions.
Status bar
Signal indicator The signal indicator shows the reflected light intensity:
Level 4 (maximum) Level 3 Level 2 Level 1 (minimum) If this icon is blinking, the signal is flickering. If this icon is blinking rapidly, the signal is low. If this icon is blinking slowly, there is no signal. If there is no icon, analog power for EDM is off.
33
Getting Started
Input mode indicator The Input mode indicator only appears when you are entering points or coordinates. It shows the data input mode:
Input mode is numeric. Press a key on the number pad to enter the number printed on the key. Input mode is alphabetic. Press a key on the number pad to enter the first letter printed beside the key. Press the key repeatedly to cycle through all the letters assigned to that key. For example, to enter the letter O in alphabetic mode, press [5] three times.
Lumi-guide indicator The Lumi-guide indicator shows the status of the Lumi-guide tracking light.
Lumi-guide tracking light is on. If there is no icon, the Lumi-guide tracking light is turned off.
EDM measurement status When you are taking measurements, the EDM measurement status shows the mode that is being used. When you display observation data, the EDM measurement status shows the mode that was used when the data was collected.
Reflectorless mode If there is no icon, Prism mode is being used.
Battery indicator The battery indicator shows the battery voltage level:
Level 4 (Full) Level 3 Level 2 Level 1 Battery low
34
Getting Started
. To adjust the
Switch 1 (backlight)
LCD backlight is on. LCD backlight is off.
Switch 3 (Lumi-guide)
Lumi-guide tracking light is on. Lumi-guide tracking light is off.
35
Getting Started
Switch 4 (Sound)
Sound is on. Sound is off.
Contrast adjustment window When the 4-switch window is open, press [<] or [>] to display the contrast adjustment window. Then press [^] or [v] to change the contrast level. The arrow indicates the current contrast level. To return to the 4-switch window, press [<] or [>]. When you have finished changing display light and sound settings, press [ESC] to close the 4-switch or contrast adjustment window.
[DSP] key
Use the key to change the current display screen or to change display settings. Switching between display screens When several display screens are available, the DSP indicator appears at the top left of the screen, and the screen indicator (for example, 1/4) appears at the top right. To move to the next available screen, press [DSP].
For example, if the DSP2 screen is currently displayed, press [DSP] to move to the DSP3 screen. The screen indicator changes from 2/4 to 3/4.
When the secondary distance unit is set, an additional screen is available. It shows the HD, VD, and SD values. For information on setting the secondary distance unit, see page 120. The smallest unit of display for distances measured in feet-and-inches is 1/16 in. Smaller units are impractical in the field. When the actual value is greater than 99999'11''15/16, the > symbol is shown. If the actual distance is less than -9999'11''15/16, the ` (solid triangle) symbol is shown. This does not affect calculations. The precise value is used internally in all cases.
36
Getting Started
Customizing items in the Basic Measurement Screen (BMS) To customize the items that are displayed on the DSP1, DSP2, and DSP3 screens: 1. 2. 3. Hold down [DSP] for one second. Use the arrow keys [^], [v], [<], and [>] to highlight the item that you want to change. Use the and softkeys to scroll through the list of items that can be displayed for this item. The items that you can choose from are HA, AZ, HL, VA, V%, SD, VD, HD, Z, and (none). 4. To save your changes, press the Save softkey. Alternatively, highlight the last item for DSP3 and press [ENT]. The DSP screens show the items you have selected.
Except for the (none) item, you cannot display the same item on more than one line of the same screen. The items displayed in the DSP1, DSP2, DSP3, and DSP4 screens are also used in the corresponding Stakeout screens (SO2, SO3, SO4, and SO5). You can also customize the displayed items in Stakeout. Header characters The following header characters can be used in DSP screens: A colon (:) indicates that tilt correction is applied to the value. A hash symbol (#) indicates that tilt correction is off. An underscore (_) under the tilt correction character indicates that Sea Level Correction or Scale factor is applied.
[MODE] key
Use the [MODE] key to change the keyboard mode for the current screen. Changing input mode while entering points or codes When the cursor is in a point (PT) or code (CD) field, press [MODE] to change the input mode between alphanumeric (A) and numeric (1).
The input mode indicator in the status bar changes to show the current input mode.
When the cursor is in a height (HT) field, only numeric input mode is available. Pressing [MODE] has no effect when the cursor is in a HT field.
37
Getting Started
Quick code measurement mode 1. To activate Quick code measurement mode, press [MODE] in the BMS.
The PT field shows the default point name. 2. Press any numeric key ([0] through [9]) to start measuring and recording points. A list of the numeric keys and their assigned feature codes appears on the right side of the screen. For example, when you press [6], the code assigned to 6 is selected, and the instrument starts a measurement.
3.
If you have set the record mode to Confirm (see Measurement settings, page 53), the Record PT screen appears after each measurement. Do one of the following:
To record the point, press [ENT]. To return to the BMS, press [ESC].
To assign a new feature code to a numeric key, press [^] or [v] to highlight the code that you want to change. Then press the Edit softkey. You can use the DSP softkey to change the values shown in the measurement box, in the same way as you use the [DSP] key in the Basic Measurement Screen (BMS).
4.
To return to the BMS from the Qcode screen, press [MODE] or [ESC].
[COD] key
In the BMS, press [COD] to change the default feature code that will appear in the CD field when you record a point. Setting the default code When you press [COD] in the BMS, a window for entering the feature code appears. You can use the List and Stack softkeys to enter the code.
38
Getting Started
Qcode observations To enter the Quick code observation routine, press the Qcode softkey. In this function, you can use the ten numeric keys to both select a feature code and shoot a point. To change the measurement mode for the Quick code observation, press the Sett softkey.
In Quick code measurement, the Rec mode can only be set to Confirm or ALL.
[HOT] key
The HOT key menu is available on any observation screen. To display the HOT key menu, press [HOT].
Changing the height of the target To change the height of the target, press [HOT] to display the HOT menu. Then either press [1] or select HT and press [ENT]. Enter the height of the target, or press the Stack softkey to display the HT stack. The HT stack stores the last 20 HT values entered. Setting the temperature and pressure To set the current temperature and pressure, press [HOT] to display the HOT menu. Then either press [2] or select Temp-Press and press [ENT]. Enter the ambient temperature and pressure. The ppm value is updated automatically.
39
Getting Started
Selecting the target set A target set specifies settings for the target type, the prism constant, and height of target. When you change the selected target set, all three settings are changed. You can use this function to quickly switch between two types of target. You can prepare up to five target sets. Press [HOT] to display the HOT menu. Then either press [3], or select Target and press [ENT]. A list of the five target sets appears. To select a target set, either press the corresponding numeric key ([1] through [5]), or use [^] or [v] to highlight the target set in the list and press [ENT]. To change the settings defined in a target set, highlight the target set in the list. Then press the Edit softkey.
Type Const HT Prism / N-Prism -999 to 999 mm -9.9900 to 99.9900 m
HT can be left blank in the target set. If you leave it blank, the current HT value is always applied to the measurement. When a target set is selected, the Type and Const values are copied to both [MSR1] and [MSR2] settings, and to the measurements in Qcode. If you have specified a value for HT, this value is also copied to the current HT.
Entering a field note To enter a field note, press [HOT] to display the HOT menu. Then either press [4], or select Note and press [ENT]. This function can be used at any time on any observation screen. Each note can be up to 50 characters. The note is stored as a CO record in the raw data.
To display a list of previously used notes, press the Stack softkey. The stack stores the last 20 notes.
[ENT]
Use [^] or [v] to highlight a note in the list. Then press to select the note.
40
Getting Started
Setting the default point name To change the default point name, press [HOT] to display the HOT menu. Then press [5], or select Default PT and press [ENT]. This function is available from any observation screen. Modify the default point name for the next record. Press [ENT] to confirm the new default point name. The new point name is appears as the default PT name on the input screen.
Bubble indicator
The bubble indicator is automatically displayed if the instrument goes out of level while the compensators are turned on. To display the bubble indicator in an observation screen, press To turn the leveling compensators on or off, press [<] or [>]. When the leveling compensators are turned off, the text OFF appears on the screen. .
If the instrument is more than 3'30" out of level, the text OVER appears on the screen. To return to the observation screen, press [ESC] or [ENT].
The current setting of leveling compensators is indicated by header characters (:, #, :, and #) after field labels (such as HA, VA, SD, and HD) in observation screens. For more information, see Header characters, page 37.
41
Getting Started
[LG] key
To turn the Lumi-guide tracking light on or off, press [LG] in the Basic Measurement Screen (BMS) or in any other measurement screen. The Lumi-guide icon in the status bar shows whether the Lumi-guide tracking light is turned on or off. For more information, see Status bar, page 33.
[USR] keys
If you use a function frequently in the field, you can assign it to the [USR1] or [USR2] key. Whenever you press a [USR] key, the function that is assigned to that key is activated directly. The following functions can be assigned to the [USR] keys:
Input HT BS Check Base XYZ Default PT Select Target Input Temp-Press Input Note The following menus, or a single function from one of these menus:
By default, Input HT is assigned to [USR1], and no function is assigned to [USR2]. Hold down the [USR] key for one second to display the list of functions that can be assigned to the key. The currently assigned function is indicated by an asterisk (*) beside the function name. To change the function that assigned to the key, press [^] or [v] to highlight the function. Then press [ENT]. If an item on the list has an arrow (->) beside it, this item is a menu. If you highlight a menu item and then press [ENT], a sub-menu appears.
42
Getting Started
The first item on the sub-menu ends with the text [MENU]. If you select this item, the whole menu is assigned to the [USR] key.
[^]
To assign a specific function from the sub-menu, press or [v] to highlight the function. Then press [ENT].
Once you have assigned a function to a [USR] key, it is called directly whenever you press that [USR] key in the BMS.
To change the type of data that is assigned to the [USR] keys in MENU > 1sec-Keys > [USR]. For more information, see [USR] key settings, page 139.
[DAT] key
Use the [DAT] key to quickly access data in the current job from observation screens. When you press [DAT] in the BMS or in observation screens in functions such as Stakeout, 2Pt RefLine, and Arc RefLine, the assigned data in the current job appears. Hold down [DAT] for one second in the BMS or an observation screen to display the Select Format screen. Use this screen to change the type of data that is assigned to [DAT]. Press [1] or select DAT [MENU] to display the Data menu whenever you press [DAT]. When you select an option from this screen, the change is applied immediately, and the selected data type appears. Press [ESC] to return to the previous observation screen.
43
Getting Started
To change the type of data that is assigned to [DAT], go to MENU > 1sec-Keys > [DAT]. For more information, see [DAT] key settings, page 140.
List Display
Available jobs or data appear in a list display when you do any of the following:
view or edit data (MENU > Data) open the code list, point list, or Job Manager (MENU > Job) search for points or codes
In the list, the current cursor position is shown in reverse video (it appears as white text on a black background). Press [^] or [v] move the cursor one line up or down. If the Page Up icon appears, there are more pages before the current page. Press [<] to move up one page. If the Page Down icon appears, there are more pages after the current page. Press [>] to move down one page. To select an item from the list, move the cursor onto the item and press [ENT].
Inputting Data
Entering a point name or number
You can use numeric or alphanumeric names up to 16 characters long to identify points. The default name for a new point is the last point name entered, with the last digit incremented. For example, if the last point name was A100, the default name for the next point is A101. If the last character of the previous point name is alphabetic, the default point name is the last point name. When the cursor is in a PT (point) field, there are several ways to specify a point, or input coordinates.
44
Getting Started
Entering an existing point When you enter a known point name or number, the coordinates of that point are displayed briefly. A short beep sounds before the next screen appears or the next field is selected.
To adjust the duration of the coordinate window display, go to MENU > Settings > Others. To leave the window open until you press [ENT], set the XYZ disp field to +ENT. For more information, see page 120.
Entering a new point When you input a new point name or number, a coordinate input screen appears. Enter the points coordinates in NE, NEZ, or elevation-only (Z) format.
Press [ENT] on the last line (the CD field) to store the point in the current job.
Using a point without coordinates To use a point without recording the coordinates, press [ENT] in a PT field, without entering a point name.
The input coordinates are used in the calculation. They are not saved in the database.
45
Getting Started
Specifying a wildcard (*) If you include an asterisk (*) when you enter a point or code name, a list of points that match the entered text appears.
Use [^] or [v] to move the cursor to the point that you want to use. Then press [ENT]. If the Page Up or Page Down icons are displayed, use [<] or [>] to page up or page down the list. When you select a point from the list, its coordinates are displayed and a beep sounds.
Recording an instant measurement You can also input a point by recording an instant measurement. To do this, press the MsrPT softkey.
An observation screen appears. Press [MSR1] or [MSR2] to start a measurement. To change the height of the target, press the HT softkey. To go to the point recording screen when you have finished the measurement, press [ENT]. Enter the point or code name. Press [ENT].
46
Getting Started
When you move the cursor to a field, the current or default value appears in inverted text (this is the default Replace All input mode).
Press [>] to change the input mode to Overwrite mode and highlight the first character. Press [<] to move the cursor the end of the string.
Entering a point from the stack The point stack is a list of recently used points. To display the stack, press the Stack softkey when the cursor is in the PT field. Use [^] or [v] to move the cursor to the point that you want to use. Then press [ENT]. When you return to the point input screen, the selected point name is entered in the PT field, incremented by one. For example, if you selected the A101 point, A102 appears in the PT field.
The stack shows the last 20 point names used, in chronological order from last used to first used.
Entering a point from the point list To display a list of existing points, press the List softkey when the cursor is in the PT field. Use [^] or [v] to move the cursor to the point that you want to use. Then press [ENT]. When you return to the point input screen, the selected point name is entered in the PT field. You can add digits or alphabetic characters if required.
47
Getting Started
Entering a code
The CD (Code) field always defaults to the last code used. You can change the selected code on the input point screen, or you can press [COD] in the BMS. For more information, see [COD] key, page 38. You can use numeric or alphanumeric names up to 16 characters long to identify codes. Entering a code directly To enter a code directly, press [MODE] to change the input mode to alphanumeric or numeric mode. Then use the keypad to enter the code.
Entering a code from the stack The code stack is a list of recently used codes. The stack may contain up to 20 codes. To display the stack, press the Stack softkey when the cursor is in the CD field. Use [^] or [v] to move the cursor to the code that you want to use. Then press [ENT]. The selected code is copied to the CD field.
Entering a code from the code list To display a list of existing codes, press the List softkey when the cursor is in the CD field. To edit the code list, go to MENU > Data > Code List. For more information, see Editing an item in the point list or code list, page 133. Use [^] or [v] to highlight the feature code that you want to use. Then press [ENT].
48
Getting Started
A layer has an arrow at the end of the code label. If you highlight a layer in the list and then press [ENT], the codes and layers in that layer are displayed. When you return to the input screen, the selected code is entered in the CD field.
Items are shown in alphabetic order. You can also use the first character search to quickly find a code. For more information, see Advanced feature: Searching for a code by using the first character, page 49.
Advanced feature: Searching for a code by using the first character To find a code quickly when the code list appears, use the first-character search. For example, to see feature codes that begin with T, use the keypad to enter the letter T. To do this, press [1] twice. After each press of the key, the input mode field displays the selected letter. For example, if you press [1], S appears. If you quickly press [1] again, T appears. If you do not press the [1] key again, the letter T is selected. Once you have selected a letter, the cursor moves to the feature code beginning with that letter. If there is no code beginning with that letter, the cursor moves to the next available letter.
Qcodes Quick codes (Qcodes) let you shoot and record many points with feature codes in the field. You can register up to ten Quick codes. To register Qcodes, press the Edit softkey. For more information, see Quick code measurement mode, page 38.
Press [MODE] to switch Qcodes on or off. Press the Edit softkey to change the Qcode. You can edit the entire code, or just the number at the end of the code. You can still use [DSP] to change the background displays.
49
Getting Started
The default denominator is 16. If the denominator is 16, you do not have to enter it, and it is not displayed on the screen.
For example, if you enter [2] [.] [0] [8] [.] [5] [.] [ENT], it appears as 2'08& 5/ (2 feet, 8 and 5/16ths inches). The following examples show how various values are entered:
To enter ... 65' 5 3/8" 65' 65' 5" 65' 5 3/8" 5 3/8" Type ...
[6] [5] [.] [5] [.] [3] [.] [8] [ENT] [6] [5] [ENT] [6] [5] [.] [5] [ENT] [6] [5] [.] [5] [.] [6] [ENT] [0] [.] [5] [.] [3] [.] [8] [ENT] or [0] [.] [5] [.] [6] [ENT]
The numerator and denominator that you enter are automatically converted to the closest value from the following list: 0, 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1/16, 3/16, 5/16, 7/16, 9/16, 11/16, 13/16, 15/16. If the denominator is 16, it is not shown on the screen.
50
Getting Started
Jobs
To record data on the instrument, you must create or open a job.
CAUTION Before you use the instrument for the first time, check the job settings.
5.
Press the Sett softkey to check the job settings. You cannot change a jobs settings once you have created the job. Press [ENT] in the last field of the Job Sett screen to create the new job.
6.
If either of the messages MAX 32JOBs or Data Full appears, delete at least one existing job to free space. You cannot free space by deleting records in an existing job.
Creating a control job A control job, or common file, stores coordinate data that is used by several field jobs. You can create a control job in the office. 1. 2. 3. 4. Press [MENU] to open the MENU screen. Press [1] or select Job to open the Job Manager. Move the cursor to the job that you want to use as the control job. Press the FNC softkey.
51
Getting Started
5. 6.
Press [1] to open the Control Job screen. Press the Yes softkey.
Measuring Distances
Sighting a prism reflector
WARNING Never look at the sun through the telescope. If you do, you may damage or lose your eyesight.
For information on how to assemble the prism reflector, see Setting Up the Prism Reflector, page 22.
Sight the telescope to see crosshairs at the center of the prism reflector.
52
Getting Started
Measuring distances
To take a distance measurement, press [MSR1] or [MSR2] in the Basic Measurement Screen (BMS) or in any observation screen.
While the instrument is taking a measurement, the prism constant appears in a small font.
If the average count is set to 0, measurements are taken continuously until you press [MSR1], [MSR2], or [ESC]. Each time a measurement is taken, the distance is updated. If the average count is set to a value from 1 to 99, the averaged distance appears after the last shot. The field name SD changes to SDx to indicate the averaged data. If the signal level is insufficient to take a measurement, the signal icon flashes on and off. For more information, see Status bar, page 33.
To change the height of target (HT), temperature, or pressure, press [HOT]. For more information, see [HOT] key, page 39.
Settings that relate to corrections (T-P corr, Sea Level, C&R corr., and Map projection) are included in the job settings. These settings are job-specific. If you need to change any of these settings, you must create a new job. For more information, see Job settings, page 99, and Settings, page 115.
Measurement settings
To view the measurement settings, hold down [MSR1] or [MSR2] for one second. Use [^] or [v] to move the cursor between the fields. Use [<] or [>] to change the value in the selected field.
Field Target Const (prism constant) Values Prism N-Prism
53
Getting Started
Field Mode
Target field If the measurement is started with the Target field set to Prism, there is a dash in front of the prism constant. If the measurement is started with the Target field set to N-Prism, there is a right bracket ] in front of the prism constant. The symbol then constantly runs from left to right over the prism constant in the display.
The Target setting is used to apply better cyclic-error adjustment in distance measurement. It efficiently eliminates multipath reflection.
54
CHAPTER
4
Applications
In this chapter:
Q Q Q Q Q Q
4
HA Reset and Angle Operations Station Setup Stakeout Program Key Recording Measurement Data Measuring Offsets
55
Applications
To enter 12345'50", type [1] [2] [3] [.] [4] [5] [5] [0]. The displayed value is rounded to the minimum angle increment.
appears.
2. 3.
Sight the backsight and press [ENT]. Sight the foresight and press [ENT]. The horizontal angle is accumulated and the value is held again.
4. 5.
To end repeat angle measurement, press [ESC]. When you have accumulated enough horizontal angle between the backsight and the foresight, press [MSR1] or [MSR2] to take a measurement to the foresight.
56
Applications
The averaged horizontal angle appears. This value is fixed until the process is finished or cancelled.
HRx = HR + N HA = BSAz + HRx (normalized)
HRx is not updated even if the instrument is moved. 6. Press [ENT] to store the foresight as a CP record. Check the PT, HT, and CD values. Then press [ENT] to record.
In repeat angle measurement, the HA is replaced by HR. The number of repeat angles appears at the top of the screen (for example, N= 5). Horizontal angles can be measured up to 199959'59"5. This function stores both raw and XYZ data as CP records, regardless of the Store DB setting.
Face-1/Face-2 measurement
Use Face-1/Face-2 (F1/F2) measurements to obtain maximum accuracy for measuring angles. Using F1/F2 measurements effectively cancels out mechanical constant error, except for some special errors such as the vertical axis error. For more information, see Face-1/Face-2 Measurements, page 26.
To take F1/F2 data without taking a distance measurement, press [4] or select F1/F2 in the Angle menu.
If you have already taken a distance measurement to the target, you can initiate F1/F2 averaging by flipping the telescope to the other face.
For the HA to be adjusted from a F1/F2 measurement, the Backsight must also have been measured in F1/F2 during the station setup.
57
Applications
Station Setup
To open the Stn Setup menu, press [STN] in the BMS. To select a command from this menu, press the corresponding number key. Alternatively, press [<] or [>] to highlight the command and then press [ENT]. Press [^] or [v] to move up or down one page. The last function used is highlighted.
If the input point number or name is an existing point, its coordinates are displayed and the cursor moves to the HI (Height of instrument) field. If the point is new, a coordinate input screen appears. Enter the coordinates for the point. Press [ENT] after each field. When you press [ENT] in the CD field, the new point is stored. If the specified point has a code, the code appears in the CD field.
3.
Enter the instrument height in the HI field and then press [ENT].
58
Applications
The Backsight screen appears. 4. Select an input method for defining the backsight point.
To sight the backsight by entering coordinates, see the following section. To sight the backsight by entering the azimuth and angle, see page 60.
X Z
Instrument height
Xb
X0
Y0
1.
To enter coordinates for the backsight point (BS), press [1] or select Coord in the Backsight screen. Enter the point name. If the point exists in the job, its coordinates are shown. If you intend to take a distance measurement to the BS, enter the height of target in the HT field.
2. 3.
4.
To record a full shot (with HA, VA, and SD values) to the BS, press [MSR1] or [MSR2].
Azimuth calculated by coordinates
AZ
If you are measuring to a known coordinate BS, press [DSP] to display a QA screen. The QA screen shows the dHD and dVD values, which indicate the difference between the measured distance and the distance calculated from the known coordinates.
5.
Applications
6.
To finish the station setup after taking a distance measurement, press [ENT]. ST and F1 records are stored to the current job.
Advanced feature: Measuring F1 and F2 To take an angle shot and proceed to the next measurement on Face-2, press the F2 softkey.
To go directly to the Face-2 measurement after taking a distance measurement to the BS on Face-1, flip the telescope. The instrument automatically detects F1/F2.
Press [ENT] on Face-2. The delta screen appears. To record a CP record which stores the averaged HA, VA, and SD from the F1/F2 data, press the CP softkey. To record only the ST and F1/F2 records, without a CP record, press the OK softkey. Sighting the backsight by entering the azimuth angle
Z Instrument height
X Azimuth
Backsight point
X0
1.
To enter the azimuth angle to the backsight point, press [2] or select Angle in the Backsight screen.
60
Applications
2.
If there is no point name for the BS, press [ENT] on the BS field.
3.
In the AZ field, enter the azimuth angle to the BS point. If you press [ENT] without entering a value in the AZ field, the azimuth is automatically set to 000'00".
4.
Sight the BS point and press [ENT]. ST and F1 records are stored in the job. You can also use the F2 softkey for F1/F2 measurements. See Advanced feature: Measuring F1 and F2, page 60.
X Height 1 Z X1 X2 Height 2
X0 Y1
Y0
You can use a maximum of 10 points in a resection. Measurements can be distance and angle, or angle only. Calculation starts automatically when enough measurements are taken.
61
Applications
You can delete poor observations and recalculate if necessary. You can also select the BS point.
If the angle between known point 1 and known point 2 (measured from the station point) is extremely acute or extremely oblique, the resulting solution will be less reliable geometrically. For geometric reliability, select known point locations (or station point locations) that are widely spaced.
1.
To start the resection, press [2] or select Resection in the Stn Setup menu.
2.
Enter the point name for the first observation point (PT1).
3.
4.
Sight PT1 and press [MSR1] or [MSR2]. To use the F2 softkey for F1/F2 measurements, see Advanced feature: Measuring F1 and F2, page 60.
5.
6.
7.
Measure to PT2 and press [ENT]. When the instrument has enough data, it calculates the station (STN) coordinates.
62
Applications
If more than the minimum required data is available, a standard deviation screen appears. To take measurements to strengthen geometry of the resection, press the Add softkey. For information about the View softkey, see Advanced feature: Viewing and deleting a measurement in resection, page 64.
8.
When the results are satisfactory, record the station. To do this, press [ENT] or the REC softkey.
9.
Enter the height of instrument, if required. Press [ENT]. The ST field defaults to the last recorded PT + 1.
10. To change the station name, move to the ST field and edit or replace the text.
If you have set Split ST to Yes, the ST field defaults to the last recorded ST value + 1. For more information, see Others settings, page 120.
BS defaults to the first observed point. 11. To change the BS, press the Change softkey.
12. Select the BS point that you want to use and press [ENT].
13. To finish the resection setup, move the cursor to the BS field and press [ENT].
The minimum data required for a resection is either three angle shots, or one angle shot and one distance shot. If you use a distance shot, the distance between the target points must be greater than the measured distance. Stn-Z is calculated from distance-measured data. If no distances are measured, then Stn-Z is calculated using angle-only measurements to points with 3D coordinates.
63
Applications
Advanced feature: Viewing and deleting a measurement in resection To check the measurements to each known point, press the View softkey on the calculated STN (sigma or coordinate) screen.
Distributed HA errors in each direction VD errors between measured distance and calculated distance HD errors between measured distance and calculated distance
To delete a measurement (because of large sigma values, for example), highlight the measurement data or display the detail screen for the measurement. Then press the DEL softkey. The STN coordinates are automatically recalculated. To continue resection observations, press the Add softkey. The input screen for the next PT appears.
ST HI BS AZ
Station point (defaults to the last recorded PT + 1, or ST + 1, depending on the Split ST setting) Height of instrument Backsight point (blank) Backsight azimuth (defaults to zero)
64
Applications
2. 3. 4.
No default PT is assigned to the BS. Leave this field blank, or enter a BS point name. The backsight azimuth (AZ) defaults to zero, but you can change this. To complete the station setup, sight the BS and press [ENT]. When you press [ENT] in the AZ field, both HA and AZ are reset to the value you have entered.
Even if both ST and BS are known points, this function does not calculate the backsight angle (AZ) automatically. To calculate the AZ between two known points (ST and BS), use Station Setup > Known. For more information, see Setting up a station with known coordinates or azimuth, page 58.
2.
Enter the BM point and press [ENT]. When the point is found, it appears briefly. The cursor then moves to the HT field. Enter the HT and press [ENT]. Sight the BM point and press [MSR1] or [MSR2].
3. 4.
5.
To take an F1/F2 measurement, press the F2 softkey or flip the telescope to Face-2 after a distance measurement.
The updated station coordinates are displayed. You can change the HI in this screen. 6. To record the updated STN, press [ENT].
When the HI is changed, the Z coordinate is updated before the station is recorded. You must complete a station setup before you use the Remote Benchmark function.
65
Applications
1.
To enter the backsight (BS) check function, press [5] or select BS Check in the Stn Setup menu.
HA BS
Current HA reading The HA to the BS in the last station setup. Enter station coordinates for observations without recording data
2.
To reset the horizontal angle to the HA set in the last station setup sight the BS and press the Reset softkey or press [ENT]. To cancel the process and return to the BMS, press the Abrt softkey or press [ESC].
1.
To enter the Base XYZ function, press [6] or select Base XYZ in the Stn Setup menu.
2.
66
Applications
3.
To reset the horizontal angle, enter a value in the HA field and press [ENT]. If you do not need to reset the HA, leave the HA field blank and press [ENT].
2.
Enter a known point as P1. If you enter a new point name, a coordinate input screen appears. Sight P1 and press [MSR1] or [MSR2] to take a measurement. Press [ENT].
3.
To define the line by entering P2 coordinates, press [1] or select By Coord. To define the line by entering the azimuth, press [2] or select By Angle.
4.
If you select By Angle, the azimuth input screen appears. Enter the angle value and press [ENT].
A measurement screen appears. 5. Sight P2 and then press [MSR1] or [MSR2] to take a measurement. Press [ENT].
67
Applications
After the measurement to P2 is completed, the coordinates of the station are calculated. 6. 7. To record the station, press [ENT] or the REC softkey. To check your measurement, press the DSP softkey. If you defined the line by entering its azimuth, HD and VD between P1 and P2 are displayed. If you defined the line by entering the P2 coordinates, the difference of HD (dHD) and VD (dZ) between your measurement data and input coordinate data are displayed. 8. Enter the station name, the height of instrument (HI), and a feature code (CD) if required. The station name defaults to the last recorded PT + 1, or last recorded ST + 1, depending on the Split ST setting. Backsight (BS) defaults to the first point (P1). To change it, highlight the BS field and then press the Change softkey.
9.
10. To finish the setup and record the station, press [ENT] in the BS field.
Sample records CO, Temperature:20C Pressure:1013hPa Prism:0 ST,9005, ,265, ,1.2350,150.40300,150.40300 F1,265,1.6040,79.0010,90.30150,89.35260, F1,200,1.4590,50.2300,269.4035,93.50110, CO, P1-P2 HD=122.0350 VD=0.5600
68
Applications
Stakeout
FiLL R OUT CUT
IN
R L FILL CUT
To display the input screen for the distance and angle to the target, press [1] or select HA-HD in the Stakeout menu. Enter the values and press [ENT].
Horizontal distance from station point to stakeout point Vertical distance from station point to stakeout point Horizontal angle to stakeout point.
69
Applications
3. 4.
Rotate the instrument until the dHA is close to 000'00". Sight the target and press [MSR1] or [MSR2]. When the measurement is completed, the differences between the target position and the stakeout point are displayed.
dHA
Difference in horizontal angle to the target point R/L Right/Left (Lateral error) IN/OUT In/Out (Longitudinal error) CUT/FIL Cut/Fill
Once a measurement is taken, the Cut/Fill value and Z coordinate are updated as the VA is changed.
If you press [HOT] in any observation screen, the HOT key menu appears. You can use this menu at any time to change HT and T-P.
Using [DSP] to switch between display screens Press [DSP] to switch between the Stakeout display screens. The following screens are available:
S-O1 dHA R OUT CUT S-O5 S-O2 S-O3 S-O4
HA VA SD
HA VD HD
HL V% HD
S-O6
S-O7
S-O8
X Y Z
dX dY dZ
HD VD SD
The S-O8 screen is only available if the secondary distance unit is set. For more information, see Others settings, page 120. Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (S-O7, or S-O8 if the secondary distance unit is set), the S-O1 screen appears. To customize the S-O2, S-O3, and S-O4 screens, hold down [DSP] for one second. For more information, see Customizing items in the Basic Measurement Screen (BMS), page 37.
70
Applications
To record the stakeout point, press [ENT]. PT defaults to the last recorded PT+1. Press [ENT] to record the point. After recording the point, it returns to the observation screen. You can continue observation, or press [ESC] to input another angle and distance for stakeout.
2.
Enter the point name that you want to stake and press [ENT]. You can also specify the point by code or radius from the instrument. If several points are found, they are displayed in a list. Use [^] or [v] to move up and down the list. Use [<] or [>] to move up or down one page.
3.
Highlight a point in the list and press [ENT]. The delta angle and the distance to the target are shown.
dHA HD
Difference in horizontal angel to the target point. Distance to the target point
4.
Rotate the instrument until the dHA is close to 000'00". Press [MSR1] or [MSR2].
71
Applications
5.
dHZ
Ask the rodman to adjust the target position. When the target is on the intended position, the displayed errors become 0.0000 m (or 0.0000 ft).
Difference in horizontal angle to the target point. Right/Left (Lateral error) In/Out (Longitudinal error Cut/Fill
To switch between display screens, press [DSP]. This function works as in the angle-distance stakeout, except that the screen counter (for example, S-O1/8) is not displayed. For more information, see Using [DSP] to switch between display screens, page 70. During observation, you can use the flashing Lumi-guide to indicate distance. To set the tolerance for the Lumi-guide flash speed, press [S-O] in any observation screen. For more information, see Stakeout, page 118. Once a measurement is taken, the Cut/Fill value and Z coordinate are updated as the VA is changed.
6.
Use the Add Constant field in MENU > Settings > Stakeout to specify an integer that is added to the point number being staked to generate a new number for recording the staked point. The default value is 1000. For example, when you stake out PT3 with an Add Constant of 1000, the default number for SO record is 1003. For more information, see Stakeout, page 118.
After recording the point, the display returns to the observation screen. When you press [ESC], the display returns to the PT/CD/R input screen. If you entered the stakeout point using a single point name, the PT defaults to the last PT + 1. If you selected a point from the list, the display returns to the list, unless all points have been selected. Press [ESC] to return to the point input screen.
72
Applications
Advanced feature: Specifying a stakeout list by range input 1. To input points by range, press the Fr/To softkey in the PT field.
2.
Enter the start point (Fr) and the end point (To). The range between Fr and To must be less than 1001 points.
If existing points are found between Fr and To, a point list appears. To highlight a point, press [^] or [v]. To go to the stakeout observation screen, press [ENT]. If you have assigned a control job, and additional points are found in the control job, the Ctrl softkey appears under the list.
DivLine S-O
This function divides the line between the instrument and the first target by an input span number. It then guides you to stake out the points, one by one. 1. Press [3] or select DivLine S-O in the Stakeout menu.
2.
Set up the baseline. To do this, sight the target on the line (the end point) and press [MSR1] or [MSR2].
3.
73
Applications
The observation screen for the first stake (from the instrument) appears. 4. 5. Sight the prism and then press [MSR1] or [MSR2]. Use [^] or [v] to change the guide point. You can calculate and guide up to double the number of the stakes.
6.
For example, if you measure to the end point at 100 m from the instrument and set the span total to 2, the following four points are calculated and can be staked:
<1/2> HD 50 m
<2/2> 100 m
<3/2> 150 m
<4/2> 200 m
RefLine S-O
This function allows you to stake out a point based on the Sta, O/S, and dZ to a specified line. 1. Press [4] or select
RefLine S-O
2.
74
Applications
If you press [ENT] without entering a PT name, you can enter temporary coordinates which are not recorded in the job. Alternatively, press the MsrPT softkey to measure a point.
3.
4.
Enter offsets to the line. Press [ENT] in a blank field to enter the value 0.0000.
Sta O/S
dZ
Distance from P1 along the line Distance perpendicular to the line (+) Right side of the P1-P2 line (-) Left side of the P1-P2 line Difference in height from the line
5. 6.
Rotate the instrument until the dHA is close to 000'00". Sight the target and press [MSR1] or [MSR2]. When a distance measurement is taken, the difference from the design point appears.
7.
Using [DSP] to switch between display screens You can use [DSP] to switch between display screens. This function works as in the angle-distance stakeout. For more information, see Using [DSP] to switch between display screens, page 70.
75
Applications
Program Key
To display the Programs menu, press [PRG].
2.
Enter the first point for the reference line. Alternatively (to enter the point by measuring), press the MsrPT softkey.
Direct Measurement screen Press the MsrPT softkey to display a direct measurement screen. Sight the target and then press [MSR1] or [MSR2]. The Record PT screen appears. If you press [ESC] in the Record PT screen, the measured point is used but not recorded in the job.
3.
4.
Enter an asterisk (*) in the PT field to perform a wildcard search. A list of matching points appears. Highlight a point in the list and then press [ENT].
Prism
PT2
76
Applications
5.
Sta O/S dZ
Sight the prism or reflective sheet and then press [MSR1] or [MSR2].
Horizontal distance from P1 to the measure point along the P1-P2 line Horizontal offset from the P1-P2 line to the measured point Vertical offset from the P1-P2 line to the measured point
Using [DSP] to switch between display screens Press [DSP] to switch between the Stakeout display screens. The following screens are available:
REF1 REF2 REF3 REF4
Sta O/S dZ
REF5
X Y Z
HA VA SD
HA VD HD
HD VD SD
The REF5 screen is only available if the secondary distance unit is set. For more information, see Others settings, page 120. Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (REF4 or REF5), the REF1 screen appears. To store the point and its offset distance information, press [ENT]. Enter the point name and feature code. You can also use this screen to change the HT value.
Sample records CO, 2pt-Ref Pt:16 & Pt:13 Az:311.2932 CO, Sta= -12.6876 Offset= 1.3721 dZ= 0.0971 SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE
77
Applications
2. 3. 4.
Enter the start of the curve point (P1) and the azimuth of its tangent line (AZ1). To enter P1 by direct measurement, press the MsrPT softkey. Choose a method to define the arc.
P2 can be any point on the tangent line that is to exit the curve.
5.
In the radius (Rad) field, enter a positive value for a clockwise curve. Enter a negative value for a counterclockwise curve.
When all factors have been entered, the instrument calculates the curve.
78
Applications
If the curve length (Len) is too large for a circle of the given radius, it is shortened.
Press ...
Using [DSP] to switch between display screens Press [DSP] to switch between the Stakeout display screens. The following screens are available:
ARC1 ARC2 ARC3 ARC4
Sta O/S dZ
ARC5
X Y Z
HA VA SD
HA VD HD
HD VD SD
The ARC5 screen is only available if the secondary distance unit is set. For more information, see Others settings, page 120. Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (ARC4 or ARC5), the ARC1 screen appears. To record the point, press [ENT] on any observation screen. The arc is stored in comment records.
Sample records CO,Arc P1:583 AZ1=0.0000 P2:102 CO, AZ2=311.2932 Radius=50.0000 Length=125.6637 CO, Sta= -12.6876 Offset= 1.3721 dZ= 0.0971 SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE
79
Applications
2nd sighting point rSD 1st sighting point rHD Horizontal angle 0 direction 2nd sighting point rHA 1st sighting point Station point rVD
Slope distance between two points Horizontal distance between two points Vertical distance between two points Percentage of grade (rVD/rHD) 100% Vertical grade (rHD/rVD) :1 rAZ Azimuth from first point to second point
Measuring between the current point and the first point measured 1. To enter the RDM (Radial) function, press [3] or select RDM(Radial) in the Programs menu.
2.
80
Applications
The distance from the station point to the first point appears. 3. Sight the second point and press [MSR1] or [MSR2]. The distances between the first and second point are displayed
Slope distance between two points rVD Vertical distance between two points rHD Horizontal distance between two points
4.
rAZ rV% rGD
5.
To record the distance and angle information as a comment record, press [ENT] in the 1/2 or 2/2 observation screen.
Default point numbers are displayed. You can change these point numbers. To record a note, press [ENT] in the To field.
Data that you save in RDM functions is stored in RM records. For more information, see RM records, page 123. When you download data in Nikon RAW format, they are output as comment (CO) records.
81
Applications
Measuring between the current point and the immediately preceding point 1. 2. To enter the RDM (Continuous) function, press [4] or select RDM(Cont.)in the Programs menu. Follow the procedure as for a radial RDM measurement. For more information, see Measuring between the current point and the first point measured, page 80.
Difference between 1:Cont. and 2:Radial P3 P2 P1 1:Cont. (The preceding two points are subject to calculation.) P4 P3 P2 P1 P4
1.
To enter the Remote Elevation Measurement function, press [5] or select REM in the Programs menu.
2.
82
Applications
3.
4.
Loosen the vertical clamp and then turn the telescope to aim at an arbitrary point. The difference in elevation (Vh) appears.
You can use an REM measurement to update the height of target. Take a measurement to the prism, sight the bottom of the prism pole and then press [ENT].
Baseline
1.
To enter the 2-Pt Reference Plane function, press [6] or select V-Plane in the Programs menu.
2.
When you press the MsrPT softkey, a temporary observation screen appears. 3. Press [MSR1] or [MSR2]. The Record PT screen appears.
83
Applications
4.
5.
Once the plane is defined, the calculated Sta and dZ values are updated as you move the telescope. No distance measurement is required.
Sta dZ Horizontal distance from P1 to the target point along the baseline Vertical distance from P1 to the target point
Using [DSP] to switch between display screens Press [DSP] to switch between the plane display screens. The following screens are available:
PLN1 PLN2 PLN3
Sta dZ
X Y Z
HA VA
Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (PLN3), the PLN1 screen appears. To record the point, press [ENT] on any screen (VPLN1/3 to V-PLN3/3). Enter PT and CD and then press [ENT].
Sample records CO,Vertical Ref Plane Pt1:516-A1 Pt2:530 CO,Sta=68.021 dz=17.459 SS,30123-A48,1.5480,16.4020,40.4720,89.0730,14:22:47,
84
Applications
Target P2 (X2,Y2,Z2) b
(X,Y,Z)
P3 (X3,Y3,Z3)
a Stn
P1 (X1,Y1,Z1)
1.
To enter the 3-Pt Reference Plane function, press [7] or select S-Plane in the Programs menu.
2.
Enter three points to define the slope plane. To enter the point by direct measurement, press the MsrPT softkey.
If you press [ENT] in a blank field, an input screen for temporary coordinates appears. These coordinates will not be stored.
When you have entered the temporary coordinates, <Keyed-in XYZ> appears instead of the PT name.
If the plane is defined by two points (by selecting 2Pt), the vertical plane is the same as the plane used in the V-Pln function, but the indicating factors are Sta and dZ, not a and b. For more information, see Measuring distance and offset values on the vertical plane, page 83.
85
Applications
Once the plane is defined, the calculated a and b values are updated as you move the telescope. No distance measurement is required.
a Distance between P1 and the point that is perpendicular to the target point along the P1-P2 line Length of the perpendicular line from the target point to the P1-P2 line
Using [DSP] to switch between display screens Press [DSP] to switch between the plane display screens. The following screens are available:
PLN1 PLN2 PLN3
a b
X Y Z
HA VA
Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (PLN3), the PLN1 screen appears. To record the point, press [ENT] on any screen (S-PLN1/3 to S-PLN3/3). Enter PT and CD and then press [ENT].
86
Applications
To record the point, press [ENT] on the last field. When recording sideshots, stakeout records, and control shots from the Rept function, you can choose to store raw data only, XYZ data only, or both. For more information, see Recording, page 120.
If HA or VA is moved after you take a measurement but before you press [ENT], the angle recorded is the angle shown when [ENT] is pressed. In an angle-only record, SD is always recorded as 0.0000. If the point name that you want to record already exists in the job, an error message appears. Depending on the type of existing record, you can overwrite the old record with the new data. For more information, see Recording Data, page 187.
Hold down [ENT] for one second to record the measurement as a CP record.
Note If [COM] appears, data is not stored to the job when you press [ENT]. The format of the output data is defined by the setting of the Ext.Comm field in MENU > Settings > Comm. For more information, see Communications, page 118.
To output data on the COM port when you press [ENT], set the Data Rec field in MENU > Settings > Rec to COM. For more information, see Recording, page 120.
Sample output records through COM port When the Ext.Comm field is set to NIKON: TR PN: PT8 SD:000066626 HA:003856010 VA:008048500 HT:0000061757 (TR PN: point name SD HA VA HT; when ACK is returned, PN is incremented.) When the Ext.Comm field is set to SET: 0006662 0804806 0394324 97 (SD VA HA Chk-SUM)
87
Applications
Measuring Offsets
Measuring taped offsets
1. To enter the taped offset function, press [1] or select Tape in the Offset menu.
If you have not taken a distance measurement before entering this function, a temporary measurement screen appears. 2. 3. Sight the target and then press [MSR1] or [MSR2]. Enter offset distances from the measured point. Use [^] or [v] to move to the appropriate offset field.
Left (-)
You can enter any combination of taped offset distances to specify the point. 4. To go to the recording PT screen, press [ENT] in the last field. The calculated coordinates are shown. 5. 6. Enter a PT (and CD) value. Press [ENT] to record the point. Raw data is also recalculated, based on the taped offset value.
88
Applications
If you have not taken a distance measurement before entering this function, a temporary measurement screen appears. 2. 3. Sight the target and then press [MSR1] or [MSR2]. To take the angle offset, rotate the alidade and telescope. The measured distance (HD) remains unchanged. To record the offset point, press [ENT] or the OK softkey. The XYZ data is also recalculated, based on the new angle.
You can record an angle offset in the Basic Measurement Screen (BMS). After taking a distance measurement, rotate the alidade and/or telescope. Then press [ENT] to record the measured distance with the updated angle value. If you use this method, the dimension of the angle offset is not stored as a CO record. To store the CO record, use the O/S function.
4.
Two-prism pole
1. To enter the two-prism pole function, press [3] or select 2Prism Pole in the Offset menu.
2.
3.
89
Applications
4.
Enter the distance between the second prism and the target point. Alternatively, if you do not need QA information, you can leave the distance between the first and the second prism blank. If you do enter a P1-P2 distance, the QA screen appears. Compare the entered value and the measured distance to check the accuracy of the observation. To record the point, press [ENT] or the OK softkey.
5.
6.
Sample records SS,14,0.0000,38.9200,271.0350,89.2630,11:04:15,DITCH CO,2Prism O/S: P1-P2= 0.5090( 0.5060) P2-Tgt= 0.5020
In this sample data, 0.5090 is the measured value. 0.5060 is the entered value.
2.
Sight the first prism (or target) and press [MSR1] or [MSR2]. The display moves to the next screen.
3.
Sight the second prism (or target) and then press [MSR1] or [MSR2].
90
Applications
4.
Sight the alternative place on the same vertical line as the required target point.
5. 6.
To calculate the coordinates and the raw data of the target point, press [ENT]. To record the point, enter a PT (and CD) value and then press [ENT]. The height of target is fixed to 0.0000 for the offset point.
Sample records SS, 40, 0.0000, 48.3304, 169.20370, 82.02470, 10:52:37 CO, PT1, 0.0000, 48.3020,169.19165, 83.58565 CO, PT2, 0.0000, 48.3155,168.54250, 85.42440 CO, O/S MSR:40 0.0000 0.0000 169.20370 87.02340 The calculated point (TGT) is stored as a SS record. Measurements to the first and second target (P1 and P2) are stored as comment records (PT1 and PT2). The last record records the angle measurement to the ALT (vertically offset point from the actual target point).
91
Applications
1.
To enter the Input HD function, press [5] or select Input HD in the Offset menu.
2. 3. 4.
Turn the telescope in the direction of the point that you want to store. Enter the HD. Usually this is the taped distance from the instrument point. Enter a PT (and CD) value and then press [ENT]. The target point is calculated and recorded as an SS record.
92
Applications
3.
Sight a second point on the same wall with the first point measurement. Press [MSR1] or [MSR2].
4.
Sight the first point on the second wall. Press [MSR1] or [MSR2].
5.
If the two walls are at right angles, press the Calc softkey to calculate the corner point by three points.
6.
If you take a measurement to a fourth point, the corner point can be calculated as the intersection of two walls (P1-P2 and P3-P4). The default elevation is given by P4.
7.
Enter a PT (and CD) value. The height of target (HT) defaults to the value used in the last measurement. To record the corner point, press [ENT].
8.
Sample records SS, 58, 0.0000, 48.3304, 169.19165, 82.02470, 10:52:37, FLOOR2 CO, PT1, 1.0080, 48.3020,169.19165, 83.58565 CO, PT2, 1.0080, 48.3155,128.54250, 85.42440 CO, O/S MSR:40 0.0000 0.0000 169.20370 87.02340 The calculated corner point is stored as an SS record. The next three or four comment records are measured points. For example: CO, Point name (fixed to PT1, PT2 etc.), HT, SD, HA, VA.
93
Applications
If you have not taken a measurement to the circle before entering this function, a temporary measurement screen appears.
2.
Sight any point on the surface of the circle and then press [MSR1] or [MSR2].
If you use a prism attached to the surface of the circle for the distance measurement, press the +SD softkey to eliminate the offset error (from the attached point to the measured surface of the prism) before you press [ENT].
3.
If you have taken a distance measurement to the center of the circle, press the Calc softkey to calculate the offset using one edge angle observation.
4.
Sight the other edge of the circle and then press [ENT]. The instrument calculates and records the center of the circle.
It also calculates the coordinates of the center point and the radius of the circle. 5. To record the point, press [ENT] or the OK softkey.
94
Applications
Sample records SS,71,1.5000,37.0518,32.08380,81.06510,11:51:48, CO, PT1, 0.0000, 0.0000,47.05350, 83.58560 CO, PT2, 0.0000, 0.0000, 29.53010, 83.58560 CO,O/S MSR:71 1.5555 36.5418 38.28360 81.06510 CO,Radius of circle 0.356 CO,Input +SD:0.0020 The calculated point (center of the circle) is stored as an SS record. The following one or two comment records are angle-measured points. For example: CO, Point name (fixed to PT1/ PT2), HT(0.0000), SD(0.0000), HA, VA. If you press the +SD softkey before you sight Edge1, the input value is recorded at the end.
If you have not taken a distance measurement before entering this function, a temporary measurement screen appears.
2.
Enter the slope distance that you need to add or subtract. You can enter any value from 99.990 through +99.990 m (328.000 through +328.000 ft). To record the point, press [ENT].
3.
95
Applications
96
CHAPTER
5
Menu Key
In this chapter:
Q Q Q Q Q Q Q Q Q Q
5
Introduction Job Manager Cogo Settings Data Communication 1sec-Keys Calibration Time Removable Memory (External Memory)
97
Menu Key
Introduction
Use the MENU screen to access important functions and settings. To display the MENU screen, press the [MENU] key.
Job Manager
Use the job manager to open, create, delete, and manage jobs. To open the Job Manager, press [1] or select Job on the MENU screen. If there are jobs stored on the instrument, the job list appears, showing all the stored jobs. The newest job appears at the top of the list. If there are no jobs stored, the Create Job screen appears. See Creating a new job, page 99.
Symbol * @ !
Meaning Current job. Control job. Some of the job settings are different from the current job.
Press [^] or [v] to move up or down the job list. Press [ENT] to open the highlighted job. When you open a job, all job settings are automatically changed to match those used in the open job.
98
Menu Key
2. 3.
Enter a job name of up to eight characters. Press [ENT]. Do one of the following: To check the job settings, press the Sett softkey. To create a new job using the current job settings, press [ENT] or the OK softkey.
Job settings The following parameters are set when a job is created, and cannot be changed. This ensures that the data in a job is correctly stored in the database, and that all necessary corrections are applied when you store each record.
Scale factor T-P correction Sea Level C&R correction 0.999600 to 1.000400 ON/OFF ON/OFF ON/OFF
If you select US-Ft or I-Ft, an additional settings screen appears. Use this screen to specify whether to display values in Decimal-Ft or Ft-Inch.
To move between fields, press [^] or [v]. Alternatively, to move to the next field, press
[ENT].
99
Menu Key
To change the setting in the selected field, press [<] or [>]. To confirm the job settings and create the job, press [ENT] in the last field (HA). These settings are separate from other temporary settings.
Deleting a job
CAUTION There is no undelete function in the Job Manager. Before you press [ENT] or select DEL, make sure that the selected job is the one that you want to delete.
1.
In the job list, highlight the job that you want to delete.
2. 3.
Press the DEL softkey. A confirmation screen appears. Do one of the following:
To delete the selected job, press [ENT] or the DEL softkey. To cancel the deletion and return to the previous screen, press [ESC] or the Abrt softkey.
After you delete a job, the display returns to the job list.
10 0
Menu Key
To set the control job: 1. Highlight the job that you want to use.
2.
3. 4.
Press [1]. The Control Job screen appears. Do one of the following:
To set the selected job as the control job, press [ENT] or the Yes softkey. To cancel the process, press [ESC] or the No softkey.
If a control job is already assigned, the newly assigned control job replaces it as the control job. To clear the control job selected, highlight the current control job in the job list, press the FNC softkey and then press [1]. In the Control Job <OFF> screen press [ENT] or the Yes softkey to confirm.
The Information screen shows the number of records in the job, the free space, and the date when the job was created. Free space indicates how many points can be stored in the job. To return to the job list, press any key.
1 01
Menu Key
Importing a job
To import a job from the CompactFlash card or USB memory stick to the instrument: 1. In the job list press the FNC softkey. The FNC screen appears.
2.
Press [2] or press [v] to move the highlight to Import Job (MEM->Inst.) and then press [ENT]. The CF Card (Job) screen appears. This screen displays the job list from the detachable memory.
If both a CompactFlash card and a USB memory stick are inserted in the instrument, only the content on the USB memory stick will be displayed.
Note To change the way in which the list is ordered (job name or created date), select the DSP softkey. 3. 4. Press [v] to move the cursor to the job that you want to copy and press [ENT]. Verify the job name and then select the YES softkey to copy the job to the instrument. If the job contains a lot of records, the process may take a long time. A progress bar appears. Select No to cancel the process. 5. When the job has been copied, do one of the following:
To start working on the job immediately, select Yes. To return to the menu screen, select Abrt.
10 2
Menu Key
Exporting a job
If you want to keep a job file for future use, you can export the job file to a CompactFlash card or a USB memory stick. To export a job: 1. Highlight the job that you want to export to the external memory device.
2.
3.
Press [3] or press [v] to highlight Export Job (Inst. -> MEM) and then press [ENT]. The Export Job screen appears. Verify the job name and then select the YES softkey to export the job to the memory storage device. If the job contains many records, the process may take a long time. A progress bar appears. Select No to cancel the process.
4.
Do NOT remove the external memory device (CF card or USB memory stick) while the progress bar is displayed.
5.
When the job export is complete, the Delete JOB screen appears. Do one of the following:
To delete the job, select DEL. To cancel the process, select Abrt.
1 03
Menu Key
Cogo
Use the Cogo menu to perform coordinate geometry (COGO) calculations. You can access this menu at any time from any observation or PT input screen. To open the Cogo menu, press [2] or select Cogo on the MENU screen.
2.
If you press [ENT] without entering a point name, a coordinate input screen appears, and you can enter coordinates. These coordinates are not stored to the database. If you want to store the point, specify a new point name.
3.
Enter the second point number/name and press [ENT]. The MsrPT softkey allows you to shoot the point on the spot to use it in the calculation.
The azimuth, horizontal distance, and vertical distance from the first point to the second point are displayed. 4. Do one of the following:
To return to the PT input screen, press [ESC]. To return to the COGO menu, press [ENT].
10 4
Menu Key
GD V% rSD
3Pt angle The 3Pt Angle function calculates the angle between two lines defined by three points. To calculate a 3Pt angle: 1. Press [2] or select 3Pt Angle in the Inverse menu. P1 is the base point. Two lines are to be defined by P2 and P3, both from P1. 2. 3. Enter the point name, or use the MsrPT softkey to take a measurement to the point. Enter the second point (P2) to define the baseline (P1-P2). The angle (dHA) is measured from the baseline.
4.
Enter the third point (P3) to define the second line (P1-P3).
When you press the MsrPT softkey, a temporary measuring screen appears. Sight the target and press [MSR1] or [MSR2] to take a measurement. After the measurement, a recording point screen appears. To store the measured point, enter the PT, HT, and CD values and press [ENT]. To use the point without recording it, press [ESC].
When you have entered three points, the instrument calculates the angle and distances. 5. Do one of the following:
To return to the Inverse menu, press [ENT]. To return to the Input BasePt screen, press [ESC].
1 05
Menu Key
Enter the base point (P1). Enter the point name then and press [ENT].
Enter the azimuth, horizontal distance, and vertical distance. Then press [ENT].
If you do not enter a value in the dVD field, the value 0.0000 is used. A recording point screen with the calculated coordinates appears. PT defaults to the last recorded PT + 1. Press [ENT] to store the point.
Traverse To open the Traverse (2Pt Angle) function, press [2] or select Traverse in the Input menu. Traverse function calculates a new point based on the two defined points and the angle, horizontal and vertical distances from the line that is defined by those two points.
10 6
Menu Key
Enter the plus-minus angle, horizontal distance, and vertical distance from the baseline defined by P1-P2. If you do not enter a value in the dVD field, the value 0.0000 is used. When you press [ENT] in the dVD field, a new point is calculated. The PT name defaults to the last recorded PT + 1. To record the new point and return to the point input screen, press [ENT]. P1 (base PT) defaults to the previously recorded PT. P2 defaults to the previous P1.
To continuously calculate a new point, enter +Ang, HD, and dVD from the previous bearing line. This is a convenient way to enter Traverse points.
Entering coordinates To manually enter the XYZ coordinates, press [3] or select Input XYZ in the Input menu. The PT name defaults to the last recorded PT + 1. Enter the coordinates using the numeric keys. To move to the next field, press [ENT] or [v] in a field
To store the point as an MP record and return to the point input screen, press [ENT] in the Z field. The default PT is incremented to the next value.
1 07
Menu Key
The first and last points that you enter are joined to close the area. You must enter the points in the order in which they define the lot. You can enter up to 99 points.
Select the END softkey or [ENT] to display the confirmation screen for storing the result. A confirmation screen appears. Select the Cont. softkey or [ESC] to return to the Input PT screen to input a new point. To save the calculated values as an area (AR) record, select the Yes softkey or press [ENT] to open the Input Area name screen. To return to the Input PT menu without recording the results, select the No softkey. To cancel the process, press [ESC].
10 8
Menu Key
If you chose to store the area, enter a name to identify the area and then press [ENT].
When you download data in Nikon RAW format, area (AR) records are output as comment (CO) records.
Advanced feature: Entering a range of points To quickly enter a sequential range of points, use the range input function. To access this function, press the Fr/To softkey in the No. 01 or No. 02 input screens.
Enter the start point name in the Fr field and the end point name in the To field. You can include letters and hyphens in the point names, but the last character must be numeric. Press [ENT] in the To field to start searching for matching points. The counter shows the number of matching points found.
When the search is complete, you are returned to the Input PT screen. Press the Calc softkey to calculate the area and perimeter, or enter point names in the PT field. Press [ESC] to return to the Input PT screen with the preceding point name.
1 09
Menu Key
Enter the horizontal distance along the baseline (Sta), the horizontal distance perpendicular to the line (O/S), and the vertical distance (dVD).
A negative value in the Sta field means the opposite direction along the defined bearing line. A negative value in the O/S field is for the left-hand side of the bearing line.
To calculate the coordinates of the point (PM), press [ENT] in the dVD field. You can change the Z coordinate here.
11 0
Menu Key
The coordinates are stored as a CC record. Line definition information and Sta, O/S, and dVD values are stored in comment (CO) records.
2.
Enter the first point name and then press [ENT]. Alternatively, to measure directly to the point, press the MsrPT softkey.
3.
4.
To define the line by two points, press the Pts softkey. The Fr field defaults to the P1 point, but you can change the selected point. In the To field, enter or measure to the second point. For more information about the O/S softkey, see Advanced feature: Entering angle and distance offsets, page 115.
5.
To return to the previous screen, press [ENT]. The calculated value appears in the AZ field. To go to the next screen, press [ENT].
111
Menu Key
6.
7.
To calculate the coordinates of the intersection point, press [ENT] in the AZ field. The calculated coordinates are displayed. You can input a Z coordinate if necessary.
8. 9.
Sample records
Enter a value in the PT field and in the CD field. To record the point, press [ENT].
Calculating a bearing-distance intersection 1. Press [2] or select Brng-Dist in the Intersection menu. Brng-Dist calculates the intersection point formed by one line and one distance (radius). 2. Enter a point on the line. The line can be defined by two points or by a point and an azimuth. 3. Enter the second point (P2) as the center of the circle.
4.
To define the distance (HD) by two points, press the Pts softkey. To calculate the coordinates of the intersection point, press [ENT] in the HD field.
11 2
Menu Key
5.
If there are two results, the first solution appears graphically relative to the P1-P2 line. To display the second solution, press [<] or [>]. To record the point, press [ENT] when the required solution appears. Enter a Z coordinate, if necessary. To move to the PT and CD fields, press [ENT].
6. 7. 8.
Calculating a distance-distance intersection 1. 2. Press [3] or select Dist-Dist in the Intersection menu. Enter the first point name and press [ENT], or press the MsrPT softkey to measure directly to the point.
3. 4.
Enter the distance from P1 and press [ENT]. To define the distance (HD) by two points, press the Pts softkey. Enter P2 and the distance from P2 (HD). To calculate the coordinates of the intersection point, press [ENT] in the HD field. Press [<] or [>] to display the second solution. To record the point, press [ENT] when the required solution appears. Enter a Z coordinate, if necessary. Press [ENT] to move to the PT and CD fields.
5. 6.
7. 8.
9.
113
Menu Key
Calculating a point-line intersection 1. 2. Press [4] or select Pt-Line in the Intersection menu. Enter the first point name and then press [ENT], or press the MsrPT softkey to measure directly to the point.
3.
Enter the azimuth, or press the Pts softkey to enter another point name on the line.
4.
Enter the perpendicular point to the line, or press the MsrPT softkey to take a measurement to the point. To calculate the coordinates of the intersection point, press [ENT]. If P1 and P2 are 3D points, the Z coordinate of the perpendicular point is calculated relative to the P1-P2 slope.
5.
6.
11 4
Menu Key
Advanced feature: Entering angle and distance offsets To display the offset input screen, press the O/S softkey.
In the Ang field, enter a positive value to rotate the line clockwise. Enter a negative value to rotate the line counterclockwise.
In the O/S field, enter a positive value to specify an offset to the right. Enter a negative value to specify an offset to the left.
Settings
To display the Settings menu, press [2] or select Settings on the MENU screen. Use this menu to configure the initial job settings.
Some job settings, specified in the following sections, cannot be changed once a job is created. If any of these settings are changed while a job is open, a confirmation screen appears, asking you to create a new job with the new settings, or to work with those settings without recording any data. For more information, see Settings, page 188.
115
Menu Key
Angle
To open the Angle menu, press [1] or select Angle in the Settings menu.
VA zero Zenith / Horizon / Compass
When this field is set to ON, ACH and Trunnion axis compensation is applied to horizontal angle readings.
HA 0 to BS/Azimuth
The HA job setting cannot be changed once a job is created. When this field is set to Azimuth, the horizontal angle (HA) that appears and recorded is in Azimuth value. When this field is set to 0 to BS, HA is in HA zero to BS value.
Distance
To open the Distance menu, press [2] or select Distance in the Settings menu.
Scale T-P corr Sea Level C&R corr Numeric value between 0.999600 and 1.000400 ON / OFF ON / OFF OFF / 0.132 / 0.200 .
The Scale, T-P corr., Sea Level, and C&R corr. job settings cannot be changed once a job is created.
10000.0 - 106 P ------------------------------------------- 13.5951 980.665 K = 275 --------------------------------------------------------------------------273 + T K - SD SD' = 1 + ------------------- 1000000
11 6
Menu Key
Curvature and Refraction correction Because the surface of the earth is curved, the vertical difference (VD and Z) at the measurement point, as referenced to the horizontal plane, inevitably includes some error. This error is called curvature error. Also, because the density of the air surrounding the earth decreases with altitude, light is refracted at different rates at different altitudes. The error caused by this change in refraction is called refraction error.
Curvature error (A A') Refraction error (A A1') A' Horizontal P A1' direction A A1 O A' P
HD HD' VD VD' SD VA Re k
Horizontal dist. (before adj.) Horizontal dist. (after adj.) Vertical dist. (before adj.) Vertical dist. (after adj.) Slope dist. Vertical angle 6370 km C&R constant (0.132 or 0.200)
117
Menu Key
Coordinate
To open the Coordinate menu, press [3] or select Coord. in the Settings menu.
Order Lable AZ NEZ / ENZ XYZ / YXZ / NEZ(ENZ) North / South
The Order and AZ job settings cannot be changed once a job is created.
Power saving
To open the Power Save menu, press [4] or select PwrSave in the Settings menu.
Main Unit EDM Unit Sleep OFF / 5min / 10min / 30min OFF/AtOnce/0.1min/0.5min/3min/10min OFF/1min/3min/5min
Communications
To open the Communication menu, press [5] or select Comm. in the Settings menu.
Ext.Comm Baud Length Parity Stop bit NIKON / SET 1200 / 2400 / 4800 / 9600 / 19200/ 38400 bps 7/8 EVEN / ODD / NONE 1/2
Stakeout
Press [6] or select Stakeout in the Settings menu to open the Stakeout menu.
Add PT Integer between 1 and 999,999
This field sets the default point number to record observed data in stakeout.
LG Dist 0 to 9.99 m (32.8 ft)
11 8
Menu Key
If SIGNAL-LOW is detected at the instrument, the Lumi-guide flashes very slowly (0.5 Hz). The LG distance guide provides the rodman with approximate In/Out information to the design point in Stakeout, by changing the speed at which the Lumi-guide indicator flashes.
Unit
To open the Unit menu, press [7] or select Unit in the Settings menu.
Angle Distance DEG (Degree) / GON / MIL (Mil6400) Meter / US-Ft / I-F
If you select US-Ft or I-Ft, an additional settings screen appears. Use this screen to specify whether to display values in Decimal-Ft or Ft-Inch.
Temp Press
The Angle, Distance, Temp, and Press job settings cannot be changed once a job is created.
119
Menu Key
Recording
To open the Rec menu, press [8] or select Angle in the Settings menu.
Store DB RAW / XYZ / RAW+XYZ This setting determines whether raw and/or coordinate data is stored when you record SS, CP, or SO records in the Basic Measurement Screen (BMS) or Stakeout screen ON/OFF If you set this field to ON, when you record a point from the BMS, the Lumi-guide is turned on for two seconds. Internal / COM Set this field to COM to output data on the COM port when you press [ENT] in the BMS or a Stakeout screen. The data is not stored to the job file. For more information, see Outputting data to the COM port, page 87.
Rec LG
Data Rec
Others settings
To open the Others menu, press [9] or select Other in the Settings menu.
XYZ disp Fast / Norm / Slow / +ENT Defines speed to move to the next screen after showing XYZ of the input PT None / Meter / US-Ft / I-Ft When the Secondary unit is set to a unit, an extra display screen is available in the BMS, stakeout observation screens, and 2-pt reference line screens. The extra screen shows the HD, VD, and SD in the secondary unit
2nd Unit
If you select US-Ft or I-Ft, an additional settings screen appears. Use this screen to specify whether to display values in Decimal-Ft or Ft-Inch.
ON / OFF No / Yes Select Yes to separate the point numbers of station points from other record type point numbers
If you set the Split ST field to Yes, an additional setting screen appears. Use this screen to specify the starting ST number.
12 0
Menu Key
ABC/123 Sets the default input mode when a CD field appears. Up to 20 characters Enter your name or the name of your company. If you enter a value in this field, it appears at start-up
B B
Data
Tip To provide easier configuration for common regional settings, you can quickly configure the Nikon total station to a pre-set combination of default regional settings. For more information, see Changing Regional Configuration Pre-sets, page 30. Tip The Nikon total station supports up to 3 languages on the instrument. For more information on changing the language settings, see page 29.
Use the Data menu to view or edit records. To display the Data menu, press [4] on the MENU screen.
Viewing records
You can view data at any time, even in an observation screen or while entering points.
Viewing raw data To show the raw data records in a list, press [1] on the Data menu screen. When you first view the raw data, the last four raw records in the current job are displayed. Use [^] or [v] to scroll through the records. To see detailed information for the selected records, press [ENT]. To return to the record list, press [ESC].
SS, CP, F1, F2 records Raw SS, CP, F1, and F2 records contain PT, HT, CD, HA, VA, and SD fields. SS records are sideshots (topo shots). All shots from the Basic Measurement Screen (BMS) are stored as SS records.
1 21
Menu Key
CP records are shots taken in the Angle or Repeat menus, or in the BMS. For more information, see Recording a foresight point after repeat angle measurement, page 56, and Recording data from any observation screen, page 86. F1 and F2 records are Face-1 and Face-2 measurements. When the Store DB setting is set to RAW+XYZ, press [DSP] to switch between the first screen (showing HA, VA, SD, PT, and HT) and the second screen (showing X, Y, Z, PT, and CD). Coordinates are not available in F1 or F2 records. When you take more than one measurement to the same point and choose to overwrite the XYZ data, the old raw record becomes raw data only. As a result, only one SS(RAW) record keeps its corresponding SS(XYZ) record. Other SS(RAW) records to the same point no longer have coordinates available. ST records ST (station) records contain ST, HI, BS, and AZ fields. Press [DSP] to switch between the first screen (showing ST, HI, BS, and AZ) and the second screen (showing X, Y, Z, PT, and CD). When you assign a new ST point name in MENU > Stn Setup > Quick, the coordinates of the station is recorded as (0, 0, 0). SO records SO records are stakeout shots. These are shots recorded in stakeout functions. When the Store DB setting is set to RAW+XYZ, press [DSP] to switch between the first screen (showing HA, VA, SD, PT, and HT), the second screen (showing X, Y, Z, PT, and CD), and the third screen (showing dX, dY, dZ, PT, and CD). The dX, dY, and dZ fields store the difference between the stakeout shots actual position and its planned position. These fields are downloaded as comment records in Nikon RAW format. CO records A CO record is a comment added to the job from the system. For example, when you change the Stn-Z using the Remote Benchmark function, or you reset the horizontal angle using the BSCheck function, the system writes a comment record.
12 2
Menu Key
When you input a Stn-XYZ by Base-XYZ function, the recorded station appears as a comment record.
SY records When you complete a station setup, an SY record is stored. This record contains the Temperature, Pressure, and Prism Constant values.
RM records When you record measurements in RDM (Cont) or RDM (Rad), they are labeled as RM records. Each RM record consists of two screens. Press [DSP] to switch between the first screen (showing From, To, rHD, and rVD) and the second screen (showing rAZ, rSD, rV%, and rGD). When you download data in Nikon RAW format, RM records are output as comment (CO) records. AR records An AR record stores an area and perimeter calculation. When you download data in Nikon RAW format, AR records are output as comment (CO) records.
View coordinate data When you press [2] or select XYZ data in the Data menu, coordinate data appears in a list, with the newest record at the bottom of the screen. Use [^] or [v] to scroll through the records. Use [<] or [>] to move up or down one page.
1 23
Menu Key
Press [ENT] to see more detailed information about the selected record.
The header (XYZ,YXZ,NEZ, or ENZ) depends on the Coord. Label setting in MENU > Settings > Coord. For more information, see Coordinate, page 118.
UP, MP, CC, and RE records All coordinate records contain PT, CD, X, Y, and Z fields. UP records are uploaded point coordinates. MP records are manually input point coordinates. CC records are points calculated in Cogo, and RE records are points calculated in Resection. When the Store data setting is set to RAW+XYZ or to XYZ, shots in the BMS (SS records), in various O/S functions (SS records), in 2Pt-RefLine and Arc-RefLine in PRG (SS records) and in some Stakeout functions (SO records) store coordinate records as well. The format of the data is the same as other coordinate records. View records by station To view records by station, press [3] or select ST->SS/SO/CP in the Data menu.
A list of all stations appears. Use [^] or [v] to highlight the station name that you want to view. Use [<] or [>] to move up or down one page. To view detailed information about the selected station, press [ENT].
To display all the observation data from the selected station in chronological order, press [ENT] again.
Detailed data is as for raw data. For detailed information about each point type and format, see Viewing raw data, page 121.
12 4
Menu Key
Deleting records
Deleting raw records In the RAW screen, use [^] or [v] to highlight the record that you want to delete. Then press the DEL softkey.
A confirmation screen appears. To delete the selected record, press [ENT] or the Yes softkey.
If the Store DB setting is set to Both, the system also deletes the corresponding coordinate data when you delete an SS, SO, or CP record. You can also delete raw data by pressing the DEL softkey in the detailed display screen for the record.
Deleting coordinate records In the XYZ screen, use [^] or [v] to highlight the record that you want to delete. Then press the DEL softkey.
A confirmation screen appears. To delete the selected record, press [ENT] or the Yes softkey. To cancel the deletion of data, press [ESC] or the No softkey.
You can also delete coordinate data by pressing the DEL softkey in the detailed display screen for the record.
1 25
Menu Key
If the record that you want to delete is referred by an ST record, a confirmation message appears.
Deleting station records In the Station screen, use [^] or [v] to highlight the record that you want to delete. Then press the DEL softkey.
A confirmation screen appears. Press [ENT] or the Yes softkey to delete the selected record. A reconfirmation screen appears. Press the DEL softkey to confirm deletion. There is no undelete function on the instrument. Before you press the DEL softkey, make sure that you have selected the correct station record. You cannot press [ENT] in this screen. All observations from the station that you selected are deleted.
When you delete a ST record in the raw data view or the station data view, all the observation data from the station is also deleted.
Editing records
For any point record, you can edit the point name (PT), feature code (CD), height of target (HT), height of instrument (HI), backsight point (BS), and backsight azimuth (AZ).
You cannot edit the CD field for SO, F1, or F2 records. You cannot edit the HA, VA, or SD values.
12 6
Menu Key
In the RAW screen, highlight the record that you want to edit. Then press the Edit softkey.
2.
Use [^] or [v] to highlight a field. Then modify the value in the selected field.
When you change the HT of an SS, SO, or CP measurement record, its Z coordinate is recalculated.
3. 4.
When you press [ENT] on the last line of the edit screen, a confirmation screen appears. Do one of the following:
To accept the changes and return to the data view screen, press [ENT] or the Yes softkey. To return to the edit screen, press [ESC] or the No softkey.
1 27
Menu Key
Editing coordinate records You can edit PT, CD, and coordinate values in coordinate records.
You cannot edit the coordinate record for the current station.
1.
In the XYZ screen, use [^] or [v] to highlight the record that you want to edit. Then press the Edit softkey.
2. 3.
Use [^] or [v] to highlight a field. Then modify the value in the selected field. To finish editing, press [ENT] in the CD field. A confirmation screen appears.
4.
To accept the changes and return to the data view screen, press [ENT] or the Yes softkey. To go back to the edit screen, press [ESC] or the No softkey.
Editing station records Note The system will not recalculate measurements if you change the station record. All coordinate and raw data observed from an edited station record must be recalculated in your postprocessing software. In the RAW screen, use [^] or [v] to highlight the station record that you want to edit. Then press the Edit softkey.
12 8
Menu Key
You can edit any field in the ST record, but the instrument does not recalculate any measurements from this station. Press [ENT] in the AZ field to confirm the change.
If you change the ST or HI values, the coordinates of observation points are not recalculated. A comment record is stored to record the change. The following example shows a comment record for a changed HI value: CO,HI changed at ST:9012 Old HI= 1.3456m If you change the BS or AZ values, raw records are not recalculated. A comment record is stored to record the change.
Searching records
You can search for records by their type, point name, code, or by any combination of these values. Searching raw records In the RAW screen, press the Srch softkey to access the raw data search function.
To find a point by name, enter the name in the PT field and press [ENT] twice.
You can use the asterisk (*) as a wildcard. For example, when you enter 30* in the PT field, the search matches the points named 300, 301, 302, 3000A2, and 3010.
To search by point type, move to the Type field and use [<] or [>] to change the selected point type. The options are ALL, ST, SS, SO, CP, CO, CO(SY), and CO(RDM).
If you selected ST, SO, F1, or F2 in the Type field, you do not have to enter a value in the CD field. Press [ENT] in the PT field to start the search. If you selected CO, CO(SY), or CO(RDM) in the Type field, you cannot enter a value in the PT or CD fields. Press [ENT] in the Type field to start the search.
1 29
Menu Key
If more than one point matches the search criteria, the matching points are displayed in a list. Use [^] or [v] to highlight the point you want to use. Then press [ENT] to select it. Detailed data for the selected record appears. Press the DSP softkey to change the fields shown. Press [ESC] to return to the list.
If no point matches the specified criteria, an error screen appears. Press any key to return to the data screen.
Searching coordinate records In the XYZ screen, press the Srch softkey to access the XYZ data search function.
To find a coordinate by name, enter the name in the PT field and press [ENT] twice.
You can use the asterisk (*) as a wildcard. For example, when you enter 500* in the PT field, the search matches the points named 500, 500-1, 500-A, and 5000.
To search by point type, move to the Type field and use [<] or [>] to change the selected point type. The options are ALL, MP, UP, CC, and RE.
13 0
Menu Key
If more than one point matches the search criteria, the matching points are displayed in a list. Use [^] or [v] to highlight the point you want to use. Press [ENT] to select it. Detailed data for the selected record appears. Press the DSP softkey to change the fields shown. Press [ESC] to return to the list.
If no point matches the specified criteria, an error screen appears. Press any key to return to the data screen.
Entering coordinates
In the XYZ screen, press the Input softkey to display a new input point screen.
The PT field defaults to the last recorded PT + 1, but you can change the value shown. Enter the PT and CD and then press [ENT] to enter coordinates. Use the numeric keys to enter the coordinates. Press [ENT] or [v] in each field to move to the next field. When you press [ENT] in the CD field, the point is stored as an MP record. Once you record a point, the next point input screen is shown with the updated default PT.
1 31
Menu Key
The PT name list is useful if you have to handle more than one patterns of point names in the field. For example, you may need to use points named 1, 2, 3 , as well as points named A1, A2, A3 . The code list is a prepared list of feature codes. You can use it to store your own codes.
Press [4] or select PT name List in the Data menu to open the point name list. Press [5] or select Code list to open the code list. The point or code names and layers are shown in alphabetic order. Use the four softkeys to customize the list.
You can store up to 254 points, codes, or layers in each list. Each list entry can be up to 16 characters long. You can use the first character search to find a point, code, or layer in the list. In the list screen, enter the first character of the name you want to find to jump to that part of the list. For more information, see Advanced feature: Searching for a code by using the first character, page 49.
Deleting points, codes, or layers In the point or code list, use [^] or [v] to highlight the item you want to delete. Then press the DEL softkey.
A confirmation screen appears. Press [ENT] or the Yes softkey to delete the item.
13 2
Menu Key
To delete a whole layer, highlight the layer name in the list and press the DEL softkey. All codes and layers in the selected layer are deleted.
Editing an item in the point list or code list Use [^] or [v] to highlight the item that you want to edit. Then press the Edit softkey.
An editing screen appears. For points, the Edit Item screen appears. It contains only the PT field. For codes, the Edit Code screen appears, containing the CD field and the REC field. Edit the text shown and then press [ENT]. A confirmation screen appears. Press [ENT] or the Yes softkey to accept the changes and update the list.
Edit code list The Edit Code screen has two fields. The CD field contains the text that appears in the list screen. The REC field is optional. It contains the text that is stored in the job. If you leave the REC field blank, the value in the CD field is used.
You can use the REC field to use familiar words or codes on the screen, but store a numeric code in the job. For example, if you set the CD field to MANHOLE and the REC field to 1155, the text MANHOLE appears on the screen, but the code 1155 is stored.
If you press the Edit softkey when a layer name appears, only the Lyr field appears. To save changes to the layer name, press [ENT] in the Lyr field.
1 33
Menu Key
Adding a point name In the point list, press the Add softkey to add a new point name to the current layer.
The point name is added to the current layer and the list is updated.
Adding a code In the code list, press the Add softkey to add a new feature code to the current layer.
Enter the feature code in the CD field. Press [MODE] to change between alphabetic and numeric input mode.
You can use the REC field to define a numeric identifier for each feature code. This is optional: If there is a value in the REC field, this value is stored. If you leave the REC field blank, the CD value is stored. Press [ENT] to add the new code and update the code list.
13 4
Menu Key
Adding a layer 1. In the point or code list, press the Layer softkey.
2. 3.
Enter the name of the new layer. To change between alphabetic and numeric input mode, press [MODE]. To store the new layer, press [ENT]. The new layer is added to the list in alphabetic order.
Communication
Use the Communication menu to download or upload data. To display the Communication menu, press [5] or select Comm. on the MENU screen.
Downloading data
To go to the download settings screen, press [1] or select Download in the Communication menu.
Format Data
To display the total number of records that will be downloaded, press [ENT] in the Data field.
As each record in the current job is output from the instrument (downloaded), the current line number is updated.
1 35
Menu Key
After downloading is completed, you can choose to delete the current job. To delete the current job, press [4]. To return to the Basic Measurement Screen (BMS), press [ESC] or the Abrt softkey.
The default data format appears. To change the order of data fields, press the Edit softkey. For more information, see Advanced feature: Editing the data order for upload, page 137. Otherwise, just press [ENT].
Press the Job softkey to go to the Job Manager screen. For more information, see Job Manager, page 98.
To change the communication settings, press the Comm softkey and then select Serial or CF/USB in the I/O port field. The port settings must match the settings used by the terminal software on the computer. Use an RS-232C cable to connect the instrument to the computer. The Free space field shows the number of points that can be stored. Press [ENT] to put the instrument in receive mode. Then use the Send Text File command in the terminal program on the computer to start sending data.
In the terminal program, set flow control to Xon/Xoff.
13 6
Menu Key
As each point is received by the instrument, the value in the Records field is incremented.
If you press [ESC] during data upload, the upload is cancelled and the display returns to the Communication menu. Records that were received before you pressed [ESC] are stored in the job. The system truncates any code that is longer than 16 characters. Duplicate points If the existing point is a UP, CC, or MP record, and it is not referred to by any ST or BS, it is automatically overwritten by the uploaded point. No error message appears.
Advanced feature: Editing the data order for upload 1. To open the Data Fields screen, press the Edit softkey.
2. 3.
To move between the fields, press [<] or [>]. To change the selected item in a field, use the and softkeys. The options are PT, N, E, Z, CD, or blank. To save your changes and return to the previous screen, press the Save softkey.
4.
and you set the data fields to PT N E CD, then the uploaded data is:
PT=1, N=30.000, E=20.000, CD=L1
Uploading coordinates without points You can upload data without points. If you do not include a point in the format definition, each line of data is automatically assigned the next available point number. To help you to select points in the field, make sure that you store an identifier in the CD field.
The data format cannot include duplicate items. Use PT, N, E, Z and CD once each in the data format. To skip some items in your original file, set the corresponding field to blank.
1 37
Menu Key
To upload a point name list by cable, press [3] or select PT List in the Communication menu. To upload a code list, press [4] or select Code List.
Connect the RS-232C cable. Start a terminal program on the computer. To put the instrument into receive mode, press [ENT] or the OK softkey. The counter is updated as each line in the list is stored. You can store up to 254 codes or point names.
1sec-Keys
Use the 1sec-Keys menu to configure the settings for the one-second keys, [MSR], [DSP], [USR], [S-O], and [DAT]. To access this menu, press [6] or select 1sec-Keys in the MENU screen.
To change the settings for the [MSR1] key, press [1] or select MSR1. To change the settings for the [MSR2] key, press [2] or select MSR2.
13 8
Menu Key
Each [MSR] key has five settings. In the Const and AVE fields, use the numeric keys to enter values. In the other fields, use [<] or [>] to change the settings.
Tip You can also access the settings screen by holding down [MSR1] or [MSR2] for one second.
To move the cursor, use [<], [>] , [^], or [v]. To change the display item, press either the softkey or the softkey. To save the changes, press [ENT] at the last line of <DSP3> or press the Save softkey.
Tip You can also access the DSP settings screen by holding down [DSP] for one second.
There are two [USR] keys. The function that is assigned to each key appears beside the key name.
To change the settings for the [USR1] key, press [1] or select USR1. To change the settings for the [USR2] key, press [2] or select USR2.
In the Select Functions screen, the asterisk (*) indicates the function that is currently assigned to the key. To highlight a function, use [^] or [v]. To assign that function to the selected [USR] key, press [ENT].
1 39
Menu Key
There are two Stakeout settings. For more information, see Stakeout, page 118.
The asterisk (*) indicates the currently selected view format. 2. 3. To move the cursor, use [^] or [v]. To change the format displayed by [DAT], press [ENT].
Calibration
Use the Calibration screen to calibrate the instrument. To open the Calibration screen, press [7] or select Calibrat. on the MENU screen. For more information, see Adjusting, page 148.
14 0
Menu Key
Time
Use the Date & Time screen to set the current date, time, and timezone for your area. 1. To open the Date & Time screen, press [8] or select Time on the MENU screen. The current date and time settings are displayed. 2. Enter the date in Year-Month-Day format. For example, to change the date to June 18, 2002, press [2] [0] [0] [2] [ENT] [6] [ENT] [1] [8] [ENT]. If the highlighted part of the field (for example, the year) is already correct, you can just press [ENT] to use the current value. For example, if the date is already set to June 24, 2002, and you want to change the date to June 18, 2002, press [ENT] [ENT] [1] [8] [ENT]. 3. 4. To move to the Time field, press [v] or [ENT] in the Date field. Enter the time in 24-hour format. For example, to set the time to 4:35 PM, press [1] [6] [ENT] [3] [5] [ENT]. To move to the Timezone field, press [v] or [ENT] in the Time field. Use [>] or [<] arrow key to select the required timezone. Do one of the following:
5. 6. 7.
To finish setting the date and time, press [ENT] in the Timezone field. To cancel the input, press [ESC].
The time-zone is derived from the operating system. You must set the time zone properly before using the system. If you do not do this, the time that is recorded in the removable memory (CF card and USB memory) will be different from the time shown on the instrument. The time stamp of the Job file on the removable memory (CF card and USB memory) is controlled by the timezone (GMT).
1 41
Menu Key
If both an CompactFlash card and an USB memory stick are inserted in the instrument, only the content on the USB memory stick will be displayed. The job files and other files that are shown in the list are recorded in the following folders on the removable memory device (CF card or USB memory): Job files are stored in \NTTS\JOBS Other files are stored in \NTTS
2.
Rename a job file from the CF Card (Job) screen. Rename a file from the CF Card (file) screen.
14 2
Menu Key
1.
Press [v] or [^] to highlight the job or file that you want to rename.
2.
Press the Rnam softkey. The Change Name screen appears showing the current name of the job or file. Enter a new name and then press [ENT].
3.
A job name may not be longer than 8 characters. A file name may not be longer than 12 charactersthis includes the file extension. You can not use a period in a job or file name.
CAUTION There is no undelete function in the External Memory. Before you select DEL, make sure that the selected job is the one that you want to delete.
1.
Press [v] or [^] to highlight the job or file that you want to rename.
2. 3.
Press the DEL softkey. A confirmation screen appears. Do one of the following:
To delete the selected job, the DEL softkey. To cancel the deletion and return to the previous screen, press [ESC] or the Abrt softkey.
After you delete a job, the display returns to the job list.
In the Delete screen you cannot press [Ent]. You must verify the file name and then press the DEL softkey.
1 43
Menu Key
2.
14 4
CHAPTER
6
Checking and Adjustment
In this chapter:
Q Q Q Q Q
6
Checking and Adjusting the Plate Level Checking and Adjusting the Circular Level Checking and Adjusting the Optical Plummet Zero Point Errors of Vertical Scale and Horizontal Angle Corrections Checking the Instrument Constant
1 45
b. c.
Using leveling screw A, move the bubble into the center of the vial. Repeat from Step 4.
B A C
14 6
3.
Rotate the alidade 180. If the marked image is in the same position in the center of the reticle mark, no adjustment is required
P
4.
If the image is not in the same position, adjust the optical plummet: a. Use the supplied hexagonal wrench to turn the adjustment screws until the image of the X is in Position P. Position P is the center point of the line connecting the X and the center of the reticle mark . Repeat from Step 2.
b.
1 47
No adjustment is required if the zero reference for vertical angles (VA zero setting) is set to Zenith, and VA1 + VA2 equals 360. No adjustment is required if the zero reference for vertical angles (VA zero setting) is set to Horizon, and VA1 + VA2 is either 180 or 540. An adjustment is required if VA1 + VA2 is not one of the values listed above.
Note The difference between the vertical angle reading the relevant angle (either 360 for Zenith, or 180 or 540 for Horizon) is called the altitude constant.
Adjusting
There are two steps in the calibration program. Usually you only complete the first step that is described below, because the trunnion axis is finely adjusted mechanically. To make a major adjustment to the trunnion axis error compensation, however, you can complete the second step that is described below and make three sets of observations.
To set the parameters for trunnion axis error compensation, establish two targets at a horizontal distance of at least 30 m from the instrument. The first target should be placed on the horizontal plane and the second should be more than 30 above the horizontal plane. Before you set the trunnion axis compensation value, you must complete three sets of F1/F2 observations to these two points. Even if you complete the second step, the instrument cannot store a trunnion axis error compensation of more than 30". If the error is more than 30", the instrument needs a mechanical check. Second target
First target
14 8
First step 1. Take an F1 measurement to a target on the horizon. Press [ENT]. The vertical angle is shown in the V0 dir= Horiz setting.
VA1 HA1 X1 Y1 Face-1 vertical angle (tilt-off value) Face-1 horizontal angle (tilt-off value) Face-1 X axis tilt value Face-1 Y axis tilt value
If you sight a target that has a VA of more than 3, a warning message flashes on the third line.
When you have taken the measurement, the message on the bottom line changes from DO NOT TOUCH% to Turn to F2.
2.
VA2 HA2 X2 Y2
When the observation on F2 is completed, four parameters are displayed. 3. Do one of the following:
To return to the first observation screen, press [ESC] or the Redo softkey. To set parameters on the instrument, press [ENT] or the OK softkey.
1 49
4.
To go to the second step (trunnion axis compensation), press the Trun softkey.
If the HA corr. setting is set to OFF, the ACH parameter is not applied to horizontal angle readings. If this setting is set to ON, both of the ACH and trunnion-axis parameters are applied to HA. If you do not complete the second step, the trunnion-axis parameter remains set to zero, and only the ACH parameter is applied. For more information, see Angle, page 116. If ACV, ACH, X, or Y is out of range, OVER appears. Press any key to return to the first observation screen.
Second step 1. Sight the second target that is placed more than 30 degrees above the horizontal plane.
2.
Face-2 to P2 Face-1 to P2 Face-1 to P1 (Horizontal) Face-2 to P1 (Horizontal) Face-2 to P2 Face-1 to P2 Face-1 to P1 (Horizontal) Face-2 to P1 (Horizontal) Face-2 to P2 Face-1 to P2
The tolerance in angle reading to each direction is 10". To maintain the accuracy of the instrument, you must take shots with extreme care. If the dHA to the same direction is more than 10", an error message appears, and you must remeasure all three sets of points. After three sets of F1/F2 observations, the instrument calculates the trunnion axis parameter and the updated ACH (the average of each set).
15 0
3.
To return to the measurement screen for the first set of F1 measurements, press [ESC] or the Redo softkey. To go to the next set of observations for a more accurate result, press the Cont softkey. You can record up to ten sets. To store the parameter and return to the BMS, press [ENT] or the END softkey.
4.
If HA corr. is set to OFF when you finish updating the trunnion axis parameter, a message appears. The message asks if you want to change the setting. To change the setting, press the Yes softkey.
Trunnion axis compensation The trunnion axis error is reported when the vertical axis and the trunnion axis (horizontal axis) are not perpendicular to each other. The sighting axis error is from the sighting and the trunnion axes. These two errors can be compensated by applying the Tr-axis and ACH parameters on this instrument to horizontal angle readings.
ACH
Tr-axis
Because the amount of compensation changes according to the vertical angle, when compensation is enabled there is a slight movement in horizontal angle even if you clamp the tangent screw.
1 51
About 100 m
To check the instrument constant: 1. 2. 3. 4. 5. 6. 7. 8. Set up the instrument at Point P, in as flat an area as possible. Set up a reflector prism at Point Q, 100 m away from Point P. Make sure that you take the prism constant into account. Measure the distance between Point P and Point Q (PQ). Install a reflector prism on the tripod at Point P. Set up another tripod at Point R, on the line between Point P and Point Q. Transfer the NPL-632 instrument to the tripod at Point R. Measure the distance from Point R to Point P (RP), and from Point R to Point Q (RQ). Compare the value of PQ to the value RP + RQ. The difference should be within the specified range of error for the instrument ( 3 mm + 2 ppm distance). At 100 m distance, the error range is 3.2 mm. If the error is out of range, contact your dealer.
9.
10. Move the NPL-632 to other points on the line between Point P and Point Q.
15 2
11. Repeat Step 5 through Step 10 several times. 12. Calculate the average of all the values of RP, and the average of all the values of RQ. 13. Compare the value of PQ to averaged RP + averaged RQ. The difference should be within the specified range of error for the instrument ( 3 mm + 2 ppm distance). At 100 m distance, the error range is 3.2 mm. If the error is out of range, contact your dealer.
1 53
15 4
CHAPTER
7
Specifications
In this chapter:
Q Q Q
7
1 55
Specifications
Main Body
Telescope
Tube length Magnification Effective diameter of objective Image Field of view Resolving power Focusing distance Reticle illumination 153 mm (6.02 in.) 26 40 mm (1.57 in.) EDM 50 mm (1.97 in.) Erect 130' 2.6 m at 100 m (2.6 ft at 100 ft) 3.0'' 1.6 m to infinity (62.9 in. to infinity) 3-level variable
EDM
Measurement range with no haze, visibility over 40 km (25 miles) Prism mode Reflector sheet (5 cm x 5 cm) Mini-prism Standard prism (1 P) Reflectorless mode Reference target 210 m (700 ft) 300 m (984 ft) 3,000 m (9,800 ft) 5,000 m (16,400 ft)
Note - The target should not be exposed to the direct sunlight. - "Reference target" refers to a white, highly reflective material. - For measurements at short ranges. approximately 1.6 m to 5 m (5.2ft to 16.4ft) to the mini-prism, or 1.6 m to 10 m (5.2 ft to 33 ft) to the standard prism), it is recommended that you use a Nikon original prism to maintain the accuracy.
15 6
Specifications
Angle measurement
Reading system Circle diameter (reading) Minimum display increment 360 400G MIL6400 DIN18723 accuracy 1'' / 5" / 10'' 0.2 mgon / 1 mgon / 2 mgon 0.0005 MIL / 0.02 MIL / 0.05 MIL 2"/0.5 mgon Photoelectric incremental encoder Diametrical detection for H/V circles 88 mm (3.46 in.) (79 mm (3.11 in.))
Precision
Precise mode Prism (3 + 2 ppm x D) mm1 at -10 C through +40 C (+14 F through +104 F) (3 + 3 ppm x D) mm1 at -20 C through -10 C; +40 C through +50 C (-4 F through +14 F; +104 F through122 F) (5 + 2 ppm x D) mm at -10 C through +40 C (+14 F through +104 F) (5 + 3 ppm x D) mm at -20 C through -10 C; +40 C through +50 C (-4 F through +14 F; +104 F through 122 F) (10 + 5 ppm x D) mm (10 + 5 ppm x D) mm
Reflectorless
These precisions apply to measurements of 5 m(16 ft) or more to a reflector sheet and 10 m(33 ft) or more to a mini or standard prism. For measurements at shorter distances than these, the precision is 5 mm.
1 57
Specifications
Measurement intervals
Precise mode Normal mode Least count Precise mode Normal mode Prism offset correction 0.1 mm (0.0005 ft.), switchable to 1 mm (0.002 ft) 1 mm (0.002 ft), switchable to 10 mm (0.02 ft) 999 mm to +999 mm (1 mm step) 1.3 sec. (initial 2 sec.) 0.5 sec. (initial 1.6 sec.)
Lumi-guide
Light source Operational distance Positioning accuracy Beam spread High luminescence LED At least 100 m (330 ft) 6 cm at 100 m (2.4 in. at 330 ft) (approx.) About 1.5 2.6 m at 100 m point (8.5 ft at 330 ft point)
Clamps/tangent screws
Type Range 2 speed, coaxial tangent/clamp knobs 4
Tribrach
Type Detachable
Optical plummet
Image Magnification Field of view Focusing range Erect 3 5 0.5 m (1.6 ft) to infinity
15 8
Specifications
Environmental performance
Operating temperature range Storage temperature range 20 C through +50 C (4 F through +122 F) 25 C through +60 C (13 F through +140 F)
Dimensions
Main unit Carrying case 173 mm W 168 mm D 365 mm H 470 mm W 384 mm D 231 mm H
Weight
Main unit Battery BC-80 Carrying case Charger 5.1 kg (11.24 lbs), approx. 0.6 kg (1.32 lbs), approx. 4.0 kg (8.82 lbs), approx. 0.30 kg (0.66 lbs)
1 59
Specifications
CompactFlash card
CompactFlash card slot Type I / Type II x 1
USB Connecters
Note The instrument complies with USB version 1.1.
USB connector for PC USB memory stick connector 1 1
Note Depending on the USB memory model, it may take longer (30 seconds or more) for the instrument to recognize the USB memory. After you have inserted the USB memory stick into the slot, Nikon recommends that you wait a while before you start importing or exporting data from/to the memory stick. Note Some USB memory sticks may not respond to the instrument properly. Nikon recommends that you use the performance-confirmed models. Please consult your dealer for details.
Standard Components
NPL-632 main body Battery pack BC-80 Universal charger and its input code and adapters CompactFlash card (128 MB) Tool set Objective lens cap Vinyl cover
16 0
Specifications
Field Station NPL-632 Instruction Manual (this document) Carrying case Shoulder strap
C C C
CAUTION Except for the connection shown in Figure 8.1 on page 164, use of this connector is at your own risk.
CAUTION Use only the male connectors specified below. Using other connectors will damage the instrument.
CAUTION Use only the pin connections shown below. Using other connections will damage the instrument.
This connector can be used to connect to an external power source or to communicate with an external device. Before using the external device connector, make sure that the external device meets the specifications below.
Input voltage System Signal level Maximum baud rate Compatible male connector 7.2 V to 11 V DC RS-232C 9 V standard 38400 bps asynchronous Hirose HR10A-7P-6P or HR10-7P-6P
The external device connector is a Hirose HR 10A-7R-6S female connector. The pinouts for connecting it to an external device connector are shown below:
Pin 1 2 3 5 4, 6 Signal RxD TxD + Description Receive data (Input) Send data (Output) Power Ground No connection
6 5 4
HRS
1 2 3
To connect to an external power source, supply power to Pin 3 (power terminal) and Pin 5 (ground terminal) on the instrument. The instrument will use the external power source even if the carrying handle battery BC-80 is attached.
CAUTION Make sure that the power supplied is within the rated input range (7.2 V to 11 V, 1 A maximum). Power supplied outside this range will damage the instrument.
1 61
Specifications
To communicate with an external device, connect the RS-232C signal from the external device to Pin 1 (input terminal) and to Pin 2 (output terminal) on the instrument. Cap the data output/external power input connector securely while not in use. The instrument is not watertight if the cap is not attached or not attached securely, and when the data output/external power input connector is in use. The instrument can be damaged by static electricity from the human body discharged through the data output/external power input connector. Before handling the instrument, touch any other conductive material once to remove static electricity.
16 2
CHAPTER
8
System Diagrams
In this chapter:
Q
8
System Components
1 63
System Diagrams
System Components
NPL-632
Diagonal eyepiece
Solar prism
Solar filter
16 4
System Diagrams
Mini prism C
Tribrach
Nikon tripod
Figure 8.2
1 65
System Diagrams
16 6
CHAPTER
9
Communications
In this chapter:
Q Q Q
9
Uploading Coordinate Data Uploading Point Lists and Code Lists Downloading Data
1 67
Communications
Record format
You can upload coordinate records in the following formats:
PT PT PT PT PT PT PT PT PT PT , , , , , , , X X X X X X X X , , , , Z Z , , , , , Y Y Y Y Y Y Y Y , CD , , , , , Z Z Z Z , CD , CD , CD CD
16 8
Communications
Data example
20100,6606.165,1639.383,30.762,RKBSS 20104,1165611.6800,116401.4200,00032.8080 20105 5967.677 1102.343 34.353 MANHOLE 20106 4567.889 2340.665 33.444 PT1 20107 5967.677 1102.343 34.353 20109,4657.778,2335.667,,PT2 20111,4657.778,2335.667 20113 4657.778 2335.667 20115,,,34.353,MANHOLE 20117,,,33.444
1 69
Communications
File format
PT lists and code lists use the same record format. Use the filenames POINT.LST for a PT list, and CODE.LST for a code list.
DEFAULT { String1 , Code1 Layer2 { String2-1, Code2-1 String2-2, Code2-2 } Layer3 { Layer 3-1 { String3-1-1, Code3-1-1 String3-1-2, Code3-1-2 } String3-2, Code3-2 String3-3, Code3-3 } String4, Code4 String5, Code5 String6, Code6 String7, Code7
The first line of the file must contain the text DEFAULT in capital letters.
Curly brackets { } group items together under the preceding line. For example, Layer 3-1 contains String 3-1-1 and String 3-1-2. Layer 3 contains the five items from Layer 3-1 to String 3-3. String represents characters that are displayed on the screen. Code represents characters that are stored in the database.
Figure 9.1
17 0
Communications
Data example
DEFAULT { STRUCTURES { TREE, S0001 FENCE, S0002 MAIL BOX, S0003 FLOWER BED, S0004 } ROADS { MANHOLE, R0001 CENTER LINE { WHITE, R002-W YELLOW, R002-Y } SIDEWALK, R0003 CROSSING, R0004 BRIDGE, R0005 SIGNAL, R0006 HIGHWAY STAR, R0007 } RAILWAY { CROSSING, RW001 STATION, RW002 SIGNAL, RW003 BRIDGE, RW004 TUNNEL, RW005 }
1 71
Communications
Downloading Data
Settings
To configure the transmission speed and other settings, go to MENU > Settings > Comm. For more information, see Communications, page 118.
One of the following codes: UP Uploaded point MP Manually input point CC Calculated coordinate RE Resection point Point number (Point ID) Northing of the coordinate Easting of the coordinate Elevation of the coordinate Feature code
17 2
Communications
Station records
ST , stnpt , (stnid) , bspt , (bs id) , hi , bsazim , bsha
Station record identifier (fixed text) Station point number (Station ID) Backsight point number (Backsight ID) Height of instrument Backsight azimuth Backsight horizontal angle
Control point record identifier (fixed text) Point number (Point ID) Height of target Slope distance Horizontal angle Vertical angle 24-hour time stamp Feature code
Sideshot records
SS SS pt ht sd ha va time code , pt , ht , sd , ha , va , time , code
Sideshot record identifier (fixed text) Point number Height of target Slope distance Horizontal angle Vertical angle 24-hour time stamp Feature code
1 73
Communications
Stakeout records
SO SO pt (sopt) ht sd ha va time , pt , (sopt) , ht , sd , ha , va , time ,
Stakeout record identifier (fixed text) Recorded point number (Original number of point staked) Height of target Slope distance Horizontal angle Vertical angle 24-hour time stamp
F1/F2 records
face face , pt , ht , sd , ha , va , time
pt ht sd ha va time
One of the following: F1 Shot taken using Face-1 (fixed text) F2 Shot taken using Face-2 (fixed text) Point number Height of target Slope distance Horizontal angle Vertical angle 24-hour time stamp
Comment/note records
CO CO text , text Comment record identifier (fixed text) Comment text
17 4
Communications
00NM ver
2124 2540 41
42
dist
43
press
44
temp
45
coor
46
Header record identifier (fixed text) SDR download version. One of the following: SDR20V03-05 SDR2x SDR33V04-01 SDR33 Not used Download date and time (in hours and minutes) Angle units. One of the following: 1 Degrees 2 Gons 4 Mils Distance units. One of the following: 1 Meters 2 Feet Pressure units. One of the following: 1 mm Hg 2 In. Hg 3 hPa Temperature units. One of the following: 1 Celsius 2 Fahrenheit Coordinate order. One of the following: 1 NEZ 2 ENZ Not used
Instrument record
01KI1 15 621, 2843 2227, 4449 50 51 instr serNo Instr serNo 1 zero VA 0.000 0.000 0.000
Instrument record identifier (fixed text) Instrument make and model Instrument serial number Not used The reference point for vertical angles. One of the following: 1 Zenith 2 Horizon Not used Not used Not used
1 75
Communications
14 58 (2x), 520 (33) 918 (2x), 2136 (33) 1928 (2x), 3752 (33) 2938 (2x), 5368 (33) 3948 (2x), 6984 (33) 4964 (2x), 85100 (33)
Station details record identifier (fixed text) Station point number Northing of station Easting of station Elevation of station Height of instrument Station description
17 6
Communications
Coordinates record
08KI pt northing 08KI pt northing easting elevation desc easting elevation desc
14 58 (2x), 520 (33) 918 (2x), 2136 (33) 1928 (2x), 3752 (33) 2938 (2x), 5368 (33) 3954 (2x), 6984 (33)
Coordinates record identifier (fixed text) Point number Northing of the coordinate Easting of the coordinate Elevation of the coordinate Feature code
Observation record
09MC stnpt pt sd va ha desc
14 58 (2x), 520 (33) 912 (2x), 2136 (33) 1322 (2x), 3752 (33) 2332 (2x), 5368 (33) 3342 (2x), 6984 (33) 4358 (2x), 85100 (33)
Observation record identifier (fixed text) Station point number Observed point number Slope distance Vertical angle Horizontal angle Feature code
1 77
Communications
14 10NM Job identifier record ID (fixed text) 58 (2x), jobid Job name/title 520 (33) The following fields occur only in SDR33 format. 21 1 Point ID length option 22 incZ 2D or 3D coordinates. One of the following: 1 2D 2 3D T&Pcorr Atmospheric correction. One of the following: 23 1 Off 2 On C&Rcorr Curvature and refraction correction. One of the 24 following: 1 Off 2 On refcon Refraction constant. One of the following: 25 1 0.132 2 0.200 sealev Sea level correction. One of the following: 26 1 Off 2 On
Note record
13NM 14 564 note 13NM note Note record ID (fixed text) Note text
17 8
Communications
Data examples
Nikon raw data format
CO,Nikon RAW data format V2.00 CO,B: EXAMPLE5 CO,Description: SAMPLE DATA OF DOWNLOAD CO,Client: NIKON CO,Comments: YOKOHAMA PLANT CO, Downloaded 26-MAY-2006 18:56:10 CO,Software: Pre-installed software version: 1.20 CO,Instrument: Nikon NPL-632 CO,Dist Units: Metres CO,Angle Units: DDDMMSS CO,Zero azimuth: North CO,Zero VA: Zenith CO,Coord Order: NEZ CO,HA Raw data: Azimuth CO,Tilt Correction: VA:ON HA:ON CO, EXAMPLE5 <JOB> Created 22-MAY-2006 07:09:21 MC,1,,100.000,200.000,10.000, CO,Temp:20C Press:760mmHg Prism:0 22-MAY-2006 07:11:34 ST,1,,,,1.400,55.4500,55.4500 F1,,,,0.0000,90.0000,8:27:58 SS,3,1.200,330.706,326.027,20.320,07:13:46,SIGN SS,4,1.250,379.193,300.847,29.084,07:14:24,TREE SS,5,1.218,363.344,328.032,30.105,07:14:57,TREE R SO,1003,,1.240,331.220,326.783,19.998,07:18:17,
1 79
Communications
18 0
Communications
1 81
Communications
18 2
CHAPTER
10
Error Messages
In this chapter:
Q Q Q Q Q Q Q Q Q Q Q Q Q
10
Angle Cogo Communications Data Job Manager Programs Recording Data Searching Settings Stakeout Station Setup Removable Memory Devices System Error
1 83
10
Error Messages
Angle
STN Setup has to be in F1/F2
100.1
You selected ANG>F1/F2 without an F1/F2 measurement in Station Setup. Press any key to return to the previous screen. Then go to Station Setup and take F1/F2 measurement to the BS.
Cogo
NO Result
100.2
The system was unable to calculate an area because points were not entered in the correct order. Press any key to return to the Cogo menu. Then enter the points in the correct order.
Same Coordinate
100.3
The point or coordinate that you entered is identical to the previous input point. Press any key to return to the point input screen. Then use a different point.
XY-coordinate is required
100.4
The input point does not have XY (NE) coordinates. Press any key to return to the point input screen. Then enter a point that has X and Y coordinates.
Communications
If an error is detected during uploading of data, the instrument aborts the upload process and displays one of the following messages.
Check Data
100.5
There are errors in the uploaded data. The uploaded data contains errors, such as an alphabetic character in a coordinate field. Press any key. Then check the specified line in the data.
DUPLICATE PT
100.6
The uploaded data contains a duplicate PT. Press any key. Then check the specified point in the data.
CAUTION If the existing point is a UP, CC, or MP record, and is not referred by ST or BS, then it will be overwritten by the uploaded record. No error message appears.
18 4
Error Messages
10
PT MAX20 chars
100.7
The uploaded data contains a PT with a name or number that is longer than 20 digits. Press any key. Then check the specified line in the data.
XYZ OVERRANGE
100.8
The uploaded data contains a coordinate that is longer than 13 digits. Press any key. Then check the specified line in the data.
Data
Can't Edit Current ST
100.9
You have tried to edit the current ST. Note You cannot edit the current ST. However, old ST records can be edited. No recalculation can be performed on the instrument. Press any key to return to the code/layer name input screen.
Can't Edit ST/BS refer to this PT
100.10
You have tried to edit a coordinate that the current ST or BS refers to. You cannot change a coordinate if the current ST or BS refers to it. Press any key to return to the Data view screen.
Can't Edit XYZ from measurement
100.11
You have tried to change the coordinates of an SO, SS, or CP record. You cannot change the coordinates of an SO, SS, or CP record. Press any key to return to the previous screen.
DELETE Stn-XYZ
100.12
You have tried to delete a coordinate record that the current ST or BS refers to. You must confirm that you want to delete a coordinate record that the current ST or BS refers to.
To ... delete XYZ return to the previous screen without deleting XYZ Press ... the DEL softkey
1 85
10
Error Messages
Job Manager
Cannot Assign
100.13
You have tried to set the current job as the control file. Press any key to return to the previous screen. Then select a different job.
Can't Create
100.14
There is no space available to create a job or record a point. Press any key to return to the Job Manager. Then use the DEL softkey to delete old jobs.
Existing Job
100.15
You have entered an existing job name for a new job. Press any key and then change the name for the new job.
MAX 32Jobs
100.16
You are trying to create a new job when the maximum number of jobs (32) is already stored. Press any key to return to the Job Manager. Then use the DEL softkey to delete old jobs.
Programs
NO Stn Setup
100.17
You did not perform a station setup or BS check before entering the Programs function.
To ... go to the Stn Setup menu return to the BMS go to the Programs menu Press ...
WARNING Selecting Continue does not resume the last ST record. You should only use the Continue option if you are sure that the previous ST coordinates and the current HA orientation are correct. Otherwise, records in the Programs function may not be correct. XY&Z coordinate are required
100.18
Three-dimensional coordinates are required in S-Plane function. Press any key to return to the point input screen. Then enter a three-dimensional point.
18 6
Error Messages
10
Recording Data
DATA FULL
100.19
The data storage is full. Press any key to return to the Basic Measurement Screen (BMS). Then:
To ... delete unnecessary data delete jobs Go to ...
DUPLICATE PT
The input PT you are trying to record already exists in the current job. An existing coordinate record cannot be overwritten by measured data. Press any key to return to the point input screen. Change PT.
Duplicate PT
100.21
The input PT you are trying to record already exists in the current job as an SS, SO, or CP record. An existing SS, SO, or CP record can be overwritten by measured data.
To ... return to the PT input screen record RAW data and update XYZ data record RAW data only Press ...
No Open Job
No job is open.
To ... open the job list, if there are existing jobs create a new job return to the previous screen Press ...
NO Stn Setup
There is no station record in the current job, or a station setup or BS check has not been done since the program was rebooted.
To ... continue recording Press ...
[1] or select Continue. If there is already an ST record in the job, the message CO, Use current orientation appears. [2] or select STN Setup [ESC]
1 87
10
Error Messages
OVER RANGE
100.24
You are trying to record a coordinate with more than 13 digits Press any key to return to the previous screen. Then check the current ST coordinate.
Searching
PT Not Found
100.25
There is no point that matches the criteria you entered. Press any key to return to the point input screen. This message may appear in any function where the PT/CD is input, such as Station Setup or Stakeout.
Settings
Job Settings will be changed
100.26
VA zero or HA in the Angle screen (see Angle, page 116) Scale, T-P, Sea Lvl, or C&R in the Distance screen (see Distance, page 116) Coord or Az Zero in the Coordinates screen (see Coordinate, page 118) Angle, Dist, Temp, or Press in the Unit screen (see Unit, page 119)
Press ...
Note To record a point using the new settings, create a new job using the new settings.
Stakeout
Input Error
100.27
The point name style used in the Fr field is not the same as the style used in the To field. For example, the Fr field style is 1, and the To field style is A200. Press any key to return to the Fr/To input screen. Then re-enter the point name, using the same naming style in both fields.
18 8
Error Messages
10
NO Stn Setup
100.28
You did not perform a station setup or BS check before entering the Stakeout function.
To... go to the Stn Setup menu return to the Basic Measurement Screen (BMS) go to the Stakeout menu Press ...
CAUTION Selecting Continue does not resume the last ST record. You should only use the Continue option if you are sure that the previous ST coordinates and the current HA orientation are correct. Otherwise, records in the Stakeout function may not be correct.
Station Setup
Calc ST Failed Need additional PT
100.29
Calculating ST failed in resection. This message may appear after you have deleted a point the View shots screen. Press any key to return to the PT input screen. Take another shot to calculate the ST coordinate.
Same Coordinate
100.30
The input PT or coordinate is identical to the current station in STN/1:Known, or the same coordinate or point name/number is found in Resection. Press any key to return to the PT input screen. Then use a different PT.
Space LOW
100.31
There is not enough space to record a station when you start any of the Station Setup functions.
To ... return to the BMS continue Press ... press [ESC] or the Abrt softkey. Use the DEL softkey in Job Manager to delete old jobs. press [ENT] or the OK softkey. You may not be able to record the whole process.
100.32
XY-coordinate is required
The input point for ST/BS does not have N/E coordinates. Press any key to return to the PT input screen. Then use a PT that has N/E coordinates.
1 89
10
Error Messages
Z-coordinate is required
100.33
The input point for Benchmark does not have a Z coordinate. Press any key to return to the PT input screen. Then use a PT that has a Z coordinate.
There were 32 jobs (the maximum number of jobs that can be stored on the instrument) on the instrument when you tried to copy (import) a job from the removable memory device. Press [ESC] to return to the BMS screens. Press [MENU] and then press [1] to delete unnecessary job files.
No ext. memory
100.35
The system does not recognize the removable memory device in the slot. Make sure that you insert the CF card or the USB memory stick properly in the slot.
No Job Found
100.36
No job files were found in the removable memory. Make sure that the job files are stored in \NTTS\JOBS.
Memory shortage
100.37
There are too many files in the removable memory. Insert the CF card or the USB memory stick into your office computer and then delete files stored in the \NTTS\JOBS folder. You can then insert the CF card or the USB memory stick into the instrument.
This file is not Job file
100.38
The file that was imported (copied) from the removable memory to the instrument was not the Job file. Repeat the procedure to import the correct Job file from the removable memory.
Data full %
100.39
There is not enough free memory in the instrument for you to copy (import) the Job from the removable memory. Press [ESC] to return to the BMS screen. Press [MENU] and then press [1] to delete unnecessary job files.
19 0
Error Messages
10
100.40
A job with the same name already exists on the instrument when you tried to copy (import) the Job from the removable memory. A time stamp shows when the files were last updated. Press the Rname softkey to copy the file using a different name.
To protect the data on the instrument, the system is designed not to allow data to be overwritten directly by external data. If you do not need an existing file on the instrument, first delete the file from the BMS screen, using [Menu] [1] and then copy (import) the file from the removable memory. To overwrite You can overwrite data on the removable memory by pressing the OvWt softkey.
System Error
=SYSTEM ERROR=
100.41
The system has detected an internal error that is related to the lower-level system. Press any key to turn the instrument off. The system will reboot when this error is reported. If you still have more points to shoot in the site, turn the instrument on and repeat the open a job and station setup procedures. Data stored before this error will be kept safely in the Job file. If the error appears frequently, please contact your dealer or Trimble Support and report the message that appears below the =SYSTEM ERROR= line.
1 91
10
Error Messages
19 2