Coriolis 83f
Coriolis 83f
Coriolis 83f
12
71197481
Valid as of version
V 3.01.XX (Device software)
Operating Instructions
Proline Promass 83
HART
Coriolis Mass Flow Measuring System
6
Proline Promass 83 Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 5
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Installation, commissioning and operation . . . . . . . . 5
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5 Notes on safety conventions and icons . . . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . 7
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1 Nameplate of the transmitter . . . . . . . . . . . . 8
2.1.2 Nameplate of the sensor . . . . . . . . . . . . . . . 9
2.1.3 Nameplate for connections . . . . . . . . . . . . 10
2.2 Certificates and approvals . . . . . . . . . . . . . . . . . . . 11
2.3 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 11
3 Installation . . . . . . . . . . . . . . . . . . . . . 12
3.1 Incoming acceptance, transport and storage . . . . . . 12
3.1.1 Incoming acceptance . . . . . . . . . . . . . . . . . 12
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 14
3.2.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.2 Mounting location . . . . . . . . . . . . . . . . . . . 14
3.2.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.4 Special installation instructions . . . . . . . . . 18
3.2.5 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.6 Thermal insulation . . . . . . . . . . . . . . . . . . 21
3.2.7 Inlet and outlet runs . . . . . . . . . . . . . . . . . 21
3.2.8 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.9 Limiting flow . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3.1 Turning the transmitter housing . . . . . . . . 22
3.3.2 Installing the wall-mount housing . . . . . . . 23
3.3.3 Turning the local display . . . . . . . . . . . . . . 25
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 25
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 26
4.1 Connecting the remote version . . . . . . . . . . . . . . . 26
4.1.1 Connecting connecting cable for
sensor/transmitter . . . . . . . . . . . . . . . . . . . 26
4.1.2 Cable specification, connecting cable . . . . . 27
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 27
4.2.1 Transmitter connection . . . . . . . . . . . . . . . 27
4.2.2 Terminal assignment . . . . . . . . . . . . . . . . . 29
4.2.3 HART connection . . . . . . . . . . . . . . . . . . . 30
4.3 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 31
4.4 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 32
5 Operation. . . . . . . . . . . . . . . . . . . . . . 33
5.1 Display and operating elements . . . . . . . . . . . . . . . 33
5.1.1 Readings displayed (operation mode) . . . . . 34
5.1.2 Additional display functions . . . . . . . . . . . . 34
5.1.3 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.1.4 Controlling the batching processes
using the local display . . . . . . . . . . . . . . . . 37
5.2 Brief operating instructions to the function matrix . 38
5.2.1 General notes . . . . . . . . . . . . . . . . . . . . . . 39
5.2.2 Enabling the programming mode . . . . . . . . 39
5.2.3 Disabling the programming mode . . . . . . . . 39
5.3 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.3.1 Type of error . . . . . . . . . . . . . . . . . . . . . . . 40
5.3.2 Error message type . . . . . . . . . . . . . . . . . . . 40
5.3.3 Confirming error messages . . . . . . . . . . . . . 41
5.4 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.4.1 Operating options . . . . . . . . . . . . . . . . . . . 42
5.4.2 Current device description files . . . . . . . . . 43
5.4.3 Device and process variables . . . . . . . . . . . 44
5.4.4 Universal / Common practice
HART commands . . . . . . . . . . . . . . . . . . . 45
5.4.5 Device status / Error messages . . . . . . . . . . 50
5.4.6 Switching HART write protection
on and off . . . . . . . . . . . . . . . . . . . . . . . . . 53
6 Commissioning . . . . . . . . . . . . . . . . . . 54
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.2 Switching on the measuring device . . . . . . . . . . . . 54
6.3 Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.3.1 Quick Setup "Commissioning" . . . . . . . . . . 55
6.3.2 "Pulsating Flow" Quick Setup menu . . . . . . 57
6.3.3 "Batching" Quick Setup menu . . . . . . . . . . 60
6.3.4 "Gas Measurement" Quick Setup menu . . . 64
6.3.5 Data backup/transmission . . . . . . . . . . . . . 66
6.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.4.1 Two current outputs: active/passive . . . . 67
6.4.2 Current input: active/passive . . . . . . . . . . . 68
6.4.3 Relay contacts: Normally closed
/Normally open . . . . . . . . . . . . . . . . . . . . . 69
6.4.4 Concentration measurement . . . . . . . . . . . 70
6.4.5 Advanced diagnostic functions . . . . . . . . . . 75
6.5 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.5.1 Zero point adjustment . . . . . . . . . . . . . . . . 77
6.5.2 Density adjustment . . . . . . . . . . . . . . . . . . 79
6.6 Rupture disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.7 Purge and pressure monitoring connections . . . . . . 81
6.8 Data memory (HistoROM), F-CHIP . . . . . . . . . . . . 81
6.8.1 HistoROM/S-DAT (sensor-DAT) . . . . . . . . 81
6.8.2 HistoROM/T-DAT (transmitter-DAT) . . . . 81
6.8.3 F-CHIP (Function-Chip) . . . . . . . . . . . . . . . 81
7 Maintenance . . . . . . . . . . . . . . . . . . . . 82
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 82
7.2 Cleaning with pigs (Promass H, I, S, P) . . . . . . . . . . 82
7.3 Replacing seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
8 Accessories . . . . . . . . . . . . . . . . . . . . . 83
8.1 Device-specific accessories . . . . . . . . . . . . . . . . . . . 83
8.2 Measuring principle-specific accessories . . . . . . . . . 83
Proline Promass 83 Table of contents
4 Endress+Hauser
8.3 Communication-specific accessories . . . . . . . . . . . . 84
8.4 Service-specific accessories . . . . . . . . . . . . . . . . . . 84
9 Troubleshooting . . . . . . . . . . . . . . . . . 86
9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . . 86
9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 86
9.3 Process error messages . . . . . . . . . . . . . . . . . . . . . . 91
9.4 Process errors without messages . . . . . . . . . . . . . . 93
9.5 Response of outputs to errors . . . . . . . . . . . . . . . . . 94
9.6 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
9.6.1 Removing and installing printed
circuit boards . . . . . . . . . . . . . . . . . . . . . . . 96
9.6.2 Replacing the device fuse . . . . . . . . . . . . . 100
9.7 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
9.8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
9.9 Software history . . . . . . . . . . . . . . . . . . . . . . . . . 101
10 Technical data . . . . . . . . . . . . . . . . . . 103
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . 103
10.1.1 Applications . . . . . . . . . . . . . . . . . . . . . . . 103
10.1.2 Function and system design . . . . . . . . . . . 103
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
10.1.4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . 106
10.1.5 Power supply . . . . . . . . . . . . . . . . . . . . . . 107
10.1.6 Performance characteristics . . . . . . . . . . . 108
10.1.7 Operating conditions: Installation . . . . . . . 128
10.1.8 Operating conditions: Environment . . . . . 128
10.1.9 Operating conditions: Process . . . . . . . . . 129
10.1.10 Mechanical construction . . . . . . . . . . . . . 141
10.1.11 Operability . . . . . . . . . . . . . . . . . . . . . . 147
10.1.12 Certificates and approvals . . . . . . . . . . . . 147
10.1.13 Ordering information . . . . . . . . . . . . . . . 148
10.1.14 Accessories . . . . . . . . . . . . . . . . . . . . . . . 148
10.1.15 Supplementary Documentation . . . . . . . . 148
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Proline Promass 83 Safety instructions
Endress+Hauser 5
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for measuring the
mass flow rate of liquids and gases. At the same time, the system also measures fluid density and
fluid temperature. These parameters are then used to calculate other variables such as volume flow.
Fluids with widely differing properties can be measured.
Examples:
Oils, fats
Acids, alkalis, lacquers, paints, solvents and cleaning agents
Pharmaceuticals, catalysts, inhibitors
Suspensions
Gases, liquefied gases, etc.
Chocolate, condensed milk, liquid sugar
Resulting from incorrect use or from use other than that designated the operational safety of the
measuring devices can be suspended. The manufacturer accepts no liability for damages being
produced from this.
1.2 Installation, commissioning and operation
Note the following points:
Installation, connection to the electricity supply, commissioning and maintenance of the device
must be carried out by trained, qualified specialists authorized to perform such work by the
facility's owner operator. The specialist must have read and understood these Operating
Instructions and must follow the instructions they contain.
The device must be operated by persons authorized and trained by the facility's owner-operator.
Strict compliance with the instructions in the Operating Instruction is mandatory.
Endress+Hauser is willing to assist in clarifying the chemical resistance properties of parts wetted
by special fluids, including fluids used for cleaning. However, small changes in temperature,
concentration or the degree of contamination in the process can result in changes of the chemical
resistance properties. Therefore, Endress+Hauser can not guarantee or accept liability for the
chemical resistance properties of the fluid wetted materials in a specific application. The user is
responsible for the choice of fluid wetted materials in regards to their in-process resistance to
corrosion.
If carrying out welding work on the piping, the welding unit may not be grounded by means of
the measuring device.
The installer must ensure that the measuring system is correctly wired in accordance with the
wiring diagrams. The transmitter must be earthed unless special protection measures have been
taken e.g. galvanically isolated power supply SELV or PELV (SELV = Save Extra Low Voltage;
PELV = Protective Extra Low Voltage).
Invariably, local regulations governing the opening and repair of electrical devices apply.
Safety instructions Proline Promass 83
6 Endress+Hauser
1.3 Operational safety
Note the following points:
Measuring systems for use in hazardous environments are accompanied by separate
"Ex documentation", which is an integral part of these Operating Instructions.
Strict compliance with the installation instructions and ratings as stated in this supplementary
documentation is mandatory. The symbol on the front of this supplementary Ex documentation
indicates the approval and the certification body (e.g. 0 Europe, 2 USA, 1 Canada).
The measuring device complies with the general safety requirements in accordance with
EN 61010-1, the EMC requirements of IEC/EN 61326, and NAMUR Recommendation NE 21,
NE 43 and NE 53.
For measuring systems used in SIL 2 applications, the separate manual on functional safety must
be observed.
External surface temperature of the transmitter can increase by 10 K due to power consumption
of internal electronical components. Hot process fluids passing through the measuring device will
further increase the surface temperature of the measuring device. Especially the surface of the
sensor can reach temperatures which are close to process temperature. Additionally safety
precautions are required when increased process temperatures are present.
The manufacturer reserves the right to modify technical data without prior notice.
Your Endress+Hauser distributor will supply you with current information and updates to these
Operating Instructions.
1.4 Return
Do not return a measuring device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.
Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning will be
charged to the owner-operator.
Please note the measures on 101
1.5 Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements, have been tested, and left the
factory in a condition in which they are safe to operate. The devices comply with the applicable
standards and regulations in accordance with EN 61010-1 "Protection Measures for Electrical
Equipment for Measurement, Control, Regulation and Laboratory Procedures". The devices can,
however, be a source of danger if used incorrectly or for other than the designated use.
Consequently, always pay particular attention to the safety instructions indicated in these Operating
Instructions by the following icons:
#
Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"
Caution!
"Caution" indicates an action or procedure which, if not performed correctly, can result in incorrect
operation or destruction of the device. Comply strictly with the instructions.
!
Note!
"Note" indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.
Proline Promass 83 Identification
Endress+Hauser 7
2 Identification
The following options are available for identification of the measuring device::
Nameplate specifications
Order code with breakdown of the device features on the delivery note
Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is displayed.
For an overview of the scope of the Technical Documentation provided, refer to the following:
The chapters "Supplementary Documentation" 148
Der W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
Reorder
The measuring device is reordered using the order code.
Extended order code:
The device type (product root) and basic specifications (mandatory features) are always listed.
Of the optional specifications (optional features), only the safety and approval-related
specifications are listed (e.g. LA). If other optional specifications are also ordered, these are
indicated collectively using the # placeholder symbol (e.g. #LA#).
If the ordered optional specifications do not include any safety and approval-related specifications,
they are indicated by the + placeholder symbol (e.g. 8E2B50-ABCDE+).
2.1 Device designation
The "Promass 83" flow measuring system consists of the following components:
Promass 83 transmitter.
Promass F, Promass E, Promass A, Promass H, Promass I, Promass S, Promass P, Promass O or
Promass X sensor.
Two versions are available:
Compact version: transmitter and sensor form a single mechanical unit.
Remote version: transmitter and sensor are installed separately.
Identification Proline Promass 83
8 Endress+Hauser
2.1.1 Nameplate of the transmitter
A0015928
Fig. 1: Example of a transmitter nameplate
1 Name of the transmitter
2 Order code
3 Serial number (Ser. no.)
4 Extended order code (Ext. ord. cd.)
5 Power supply, frequency and power consumption
6 Additional function and software
7 Available inputs / outputs
8 Reserved for information on special products
9 Please refer to operating instructions / documentation
10 Reserved for certificates, approvals and for additional information on device version
11 Patents
12 Degree of protection
13 Ambient temperature range
Order Code:
Ser. no.:
Ext. ord. cd.:
i
1
5
6
7
8
2 3 4
10 11
13
12
9
Proline Promass 83 Identification
Endress+Hauser 9
2.1.2 Nameplate of the sensor
A0015930
Fig. 2: Example of a sensor nameplate
1 Name of the sensor
2 Order code
3 Serial number (Ser. no.)
4 Extended order code (Ext. ord. cd.)
5 Calibration factor with zero point (K-factor)
6 Nominal diameter device (Size)
7 Flange nominal diameter/Nominal pressure
8 Material of measuring tubes (Materials)
9 Max. fluid temperature (Tm)
10 Pressure range of secondary containment
11 Accuracy of density measurement (Density cal.)
12 Additional information
13 Reserved for information on special products
14 Ambient temperature range
15 Degree of protection
16 Please refer to operating instructions / documentation
17 Reserved for additional information on device version (approvals, certificates)
18 Patents
19 Flow direction
i
14
16
17
18
1
9
11
19
10
15
13
12
8
6
7
Size: K-factor:
Tm:
Materials:
Density cal.:
Ser.No.:
Order Code:
5 4 3 2
Ext. ord. cd.:
Identification Proline Promass 83
10 Endress+Hauser
2.1.3 Nameplate for connections
A0015931
Fig. 3: Example of a connection nameplate
1 Serial number (Ser. no.)
2 Possible inputs and outputs
3 Signals present at inputs and outputs
4 Possible configuration of current output
5 Possible configuration of relay contacts
6 Terminal assignment, cable for power supply
7 Terminal assignment and configuration (see point 4 and 5) of inputs and outputs
8 Version of device software currently installed (Device SW)
9 Installed communication type (Communication)
10 Information on current communication software (Drivers: Device Revision and Device Description),
11 Date of installation (Date)
12 Current updates to data specified in points 8 to 11 (Update1, Update 2)
4
7
2
3
8 12 10 11
1
9
6
2
6
(
+
)
/
2
7
(
-
)
NC:
Versorgung /
Tension d'alimentation
Observer manuel d'instruction
See operating manual
Betriebsanleitung beachten
Communication:
Drivers:
Device SW:
Ser.No.:
Supply /
2
4
(
+
)
/
2
5
(
-
)
2
2
(
+
)
/
2
3
(
-
)
2
0
(
+
)
/
2
1
(
-
)
N/L-
PE
A:
NO:
P:
L1/L+
1 2
319475-00XX
active
passive
normally open contact
normally closed contact
Date:
Update 1
ex works / ab Werk / rglages usine
Update 2
5
Proline Promass 83 Identification
Endress+Hauser 11
2.2 Certificates and approvals
The devices are designed in accordance with good engineering practice to meet state-of-the-art
safety requirements, have been tested, and left the factory in a condition in which they are safe to
operate. See also "Certificates and approvals" 147.
The devices comply with the applicable standards and regulations in accordance with EN 61010-1
"Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures" and with the EMC requirements of IEC/EN 61326.
The measuring system described in these Operating Instructions thus complies with the statutory
requirements of the EC Directives. Endress+Hauser confirms successful testing of the device by
affixing to it the CE mark.
The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
2.3 Registered trademarks
KALREZ
and VITON
Registered trademark of HART Communication Foundation, Austin, USA
HistoROM, S-DAT
, T-DAT, F-CHIP
, FieldCare
, Fieldcheck
TM > 200 C
( 392 F)
TM > 200 C
( 392 F)
Abb. H2:
Horizontal
orientation
Transmitter head
down
a0004580
Abb. H3:
Horizontal
orientation
Transmitter head to
the side
A0015445
m
= Recommended orientation; = Orientation recommended in certain situations; = Impermissible orientation
m The measuring tubes are curved. Therefore the unit is installed horizontally, adapt the sensor position to the fluid
properties:
Suitable to a limited extent for fluids with entrained solids. Risk of solids accumulating
Suitable to a limited extent for outgassing fluids. Risk of air accumulating
Installation Proline Promass 83
18 Endress+Hauser
3.2.4 Special installation instructions
Promass F, E, H, S, P and O
"
Caution!
If the measuring tube is curved and the unit is installed horizontally, adapt the sensor position to
the fluid properties.
a0004581
Fig. 9: Horizontal installation of sensors with curved measuring tube.
1 Not suitable for fluids with entrained solids. Risk of solids accumulating.
2 Not suitable for outgassing fluids. Risk of air accumulating.
Promass I and P with Eccentric Tri-clamps
Eccentric Tri-Clamps can be used to ensure complete drainability when the sensor is installed in a
horizontal line. When lines are pitched in a specific direction and at a specific slope, gravity can be
used to achieve complete drainability. The sensor must be installed in the correct position with the
tube bend facing to the side, to ensure full drainability in the horizontal position. Markings on the
sensor show the correct mounting position to optimize drainability.
a0007396
Fig. 10: Promass P: When lines are pitched in a specific direction and at a specific slope: as per hygienic guidelines
(21 mm/m or approximatley 2%). Gravity can be used to achieve complete drainability.
1 The arrow indicates the direction of flow (direction of fluid flow through the pipe).
2 The label shows the installation orientation for horizontal drainability.
3 The underside of the process connection is indicated by a scribed line. This line indicates the lowest point of the
eccentric process connection.
1 2
1
2
3
21 mm/m ( in/ft) ~2%
Proline Promass 83 Installation
Endress+Hauser 19
A0010011
Fig. 11: Promass I: When lines are pitched in a specific direction and at a specific slope: as per hygienic guidelines
(21 mm/m or approximatley 2%). Gravity can be used to achieve complete drainability.
1 The arrow indicates the direction of flow (direction of fluid flow through the pipe).
2 The label shows the installation orientation for horizontal drainability.
3 The underside of the process connection is indicated by a scribed line. This line indicates the lowest point of the
eccentric process connection.
Promass I and P with hygienic connections
(mounting clamp with lining between clamp and instrument)
It is not necessary to support the sensor under any circumstances for operational performance. If the
requirement exists to support the sensor the following recommendation should be followed.
A0007397
Fig. 12: Promass P, mounted with mounting clamp
Esc
E - +
1
2
3
21 mm/m ( 2%) ~
0.83 in/3.28 ft ( 2%) ~ 0.83 in/3.28 ft ( 2%) ~
A
B
C
DN 8 15 25 40 50
A 298 402 542 750 1019
B 33 33 33 36.5 44.1
C 28 28 38 56 75
Installation Proline Promass 83
20 Endress+Hauser
A0010008
Fig. 13: Promass I, mounted with mounting clamp
3.2.5 Heating
Some fluids require suitable measures to avoid loss of heat at the sensor. Heating can be electric,
e.g. with heated elements, or by means of hot water or steam pipes made of copper or heating
jackets.
"
Caution!
Risk of electronics overheating! Make sure that the maximum permissible ambient temperature
for the transmitter is not exceeded. Consequently, make sure that the adapter between sensor and
transmitter and the connection housing of the remote version always remain free of insulating
material. Note that a certain orientation might be required, depending on the fluid temperature.
16. For fluid temperature of 150C (302F) or above the usage of the remote version with
separate connection housing is recommended.
With a fluid temperature between 200 C to 350 C (392 to 662 F) the remote version of the
high-temperature version is preferable.
When using electrical heat tracing whose heat is regulated using phase control or by pulse packs,
it cannot be ruled out that the measured values are influenced by magnetic fields which may
occur, (i.e. at values greater than those permitted by the EC standard (Sinus 30 A/m)). In such
cases, the sensor must be magnetically shielded.
The secondary containment can be shielded with tin plates or electric sheets without privileged
direction (e.g. V330-35A) with the following properties:
Relative magnetic permeability
r
> 300
Plate thickness d > 0.35 mm (0.014")
Information on permissible temperature ranges 129
Promass X: Especially under critical climatic conditions it has to be ensured that the temperature
difference between environment and measured medium does not exceed 100 K. Suitable
measures, such as heating or thermal insulation, are to be taken.
Special heating jackets which can be ordered as accessories from Endress+Hauser are available for
the sensors.
B
C
A
DN 8 15 15FB 25 25FB 40 40FB 50 50FB 50FB 80 80
Tri-Clamp " 3/4" 1" 1" 1 " 1 " 2" 2" 2 " 3" 2 " 3"
A 373 409 539 539 668 668 780 780 1152 1152 1152 1152
B 20 20 30 30 28 28 35 35 57 57 57 57
C 40 40 44.5 44.5 60 60 80 80 90 90 90 90
Proline Promass 83 Installation
Endress+Hauser 21
3.2.6 Thermal insulation
Some fluids require suitable measures to avoid loss of heat at the sensor. A wide range of materials
can be used to provide the required thermal insulation.
a0004614
Fig. 14: In the case of the Promass F high-temperature version, a maximum insulation thickness of 60 mm (2.4") must
be observed in the area of the electronics/neck.
If the Promass F high-temperature version is installed horizontally (with transmitter head pointing
upwards), an insulation thickness of min. 10 mm (0.4") is recommended to reduce convection. The
maximum insulation thickness of 60 mm (2.4") must be observed.
3.2.7 Inlet and outlet runs
There are no installation requirements regarding inlet and outlet runs. If possible, install the sensor
well clear of fittings such as valves, T-pieces, elbows, etc.
3.2.8 Vibrations
The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by pipe vibrations. Consequently, the sensors require no special
measures for attachment.
3.2.9 Limiting flow
Relevant information can be found in the "Technical Data" section under "Measuring
range" 103 or "Limiting flow" 131.
mm (inch)
m
a
x
.
6
0
(
2
.
4
)
E s c
E- +
m
a
x
.
6
0
(
2
.
4
)
Installation Proline Promass 83
22 Endress+Hauser
3.3 Installation
3.3.1 Turning the transmitter housing
Turning the aluminum field housing
#
Warning!
The turning mechanism in devices with EEx d/de or FM/CSA Cl. I Div. 1 classification is not the
same as that described here. The procedure for turning these housings is described in the Ex-specific
documentation.
1. Loosen the two securing screws.
2. Turn the bayonet catch as far as it will go.
3. Carefully lift the transmitter housing as far as it will go.
4. Turn the transmitter housing to the desired position (max. 2 90 in either direction).
5. Lower the housing into position and reengage the bayonet catch.
6. Retighten the two securing screws.
a0004302
Fig. 15: Turning the transmitter housing (aluminum field housing)
Turning the stainless steel field housing
1. Loosen the two securing screws.
2. Carefully lift the transmitter housing as far as it will go.
3. Turn the transmitter housing to the desired position (max. 2 90 in either direction).
4. Lower the housing into position.
5. Retighten the two securing screws.
a0004303
Fig. 16: Turning the transmitter housing (stainless steel field housing)
3
5
6
1
2
4
1
2
3
4
5
Proline Promass 83 Installation
Endress+Hauser 23
3.3.2 Installing the wall-mount housing
There are various ways of installing the wall-mount housing:
Mounted directly on the wall
Installation in control panel (separate mounting set, accessories) 24
Pipe mounting (separate mounting set, accessories) 24
"
Caution!
Make sure that ambient temperature does not go beyond the permissible range
( 20 to +60 C (4 to + 140 F), optional 40 to +60 C (40 to +140 F)). Install the device
in a shady location. Avoid direct sunlight.
Always install the wall-mount housing in such a way that the cable entries are pointing down.
Mounted directly on the wall
1. Drill the holes as illustrated in the diagram.
2. Remove the cover of the connection compartment (a).
3. Push the two securing screws (b) through the appropriate bores (c) in the housing.
Securing screws (M6): max. 6.5 mm (0.26")
Screw head: max. 10.5 mm (0.41")
4. Secure the transmitter housing to the wall as indicated.
5. Screw the cover of the connection compartment (a) firmly onto the housing.
a0001130
Fig. 17: Mounted directly on the wall
a
b
c c
90 (3.54)
35 (1.38)
192 (7.56)
8
1
.
5
(
3
.
2
)
mm(inch)
Installation Proline Promass 83
24 Endress+Hauser
Installation in control panel
1. Prepare the opening in the panel as illustrated in the diagram.
2. Slide the housing into the opening in the panel from the front.
3. Screw the fasteners onto the wall-mount housing.
4. Screw threaded rods into holders and tighten until the housing is solidly seated on the panel
wall. Afterwards, tighten the locking nuts.
Additional support is not necessary.
a0001131
Fig. 18: Panel installation (wall-mount housing)
Pipe mounting
The assembly should be performed by following the instructions in the diagram.
"
Caution!
If a warm pipe is used for installation, make sure that
the housing temperature does not exceed the max. permitted value of +60 C (+140 F).
a0001132
Fig. 19: Pipe mounting (wall-mount housing)
245 (9.65)
~110 (~4.33)
210 (8.27)
+0.5 (+0.019)
0.5 (0.019)
+0.5 (+0.019)
0.5 (0.019)
mm (inch)
2070
( 0.792.75)
~ ~ 6.1) 155 (
mm (inch)
Proline Promass 83 Installation
Endress+Hauser 25
3.3.3 Turning the local display
1. Unscrew cover of the electronics compartment from the transmitter housing.
2. Press the side latches on the display module and remove the module from the electronics
compartment cover plate.
3. Rotate the display to the desired position (max. 4 45 in both directions), and reset it onto
the electronics compartment cover plate.
4. Screw the cover of the electronics compartment firmly back onto the transmitter housing.
a0003236
Fig. 20: Turning the local display (field housing)
3.4 Post-installation check
Perform the following checks after installing the measuring device in the pipe:
4 x 45
Device condition and specifications Notes
Is the device damaged (visual inspection)? -
Does the device correspond to specifications at the measuring point, including
process temperature and pressure, ambient temperature, measuring range, etc.?
5
Installation instructions Notes
Does the arrow on the sensor nameplate match the direction of flow through the
pipe?
-
Are the measuring point number and labeling correct (visual inspection)? -
Is the orientation chosen for the sensor correct, in other words suitable for sensor
type, fluid properties (outgassing, with entrained solids) and fluid temperature?
14
Process environment / process conditions Notes
Is the measuring device protected against moisture and direct sunlight? -
Wiring Proline Promass 83
26 Endress+Hauser
4 Wiring
#
Warning!
When connecting Ex-certified devices, see the notes and diagrams in the Ex-specific supplement to
these Operating Instructions. Please do not hesitate to contact your Endress+Hauser sales office if
you have any questions.
!
Note!
The device does not have an internal power switch. For this reason, assign the device a switch or
power-circuit breaker which can be used to disconnect the power supply line from the power grid.
4.1 Connecting the remote version
4.1.1 Connecting connecting cable for sensor/transmitter
#
Warning!
Risk of electric shock. Switch off the power supply before opening the device.
Do not install or wire the device while it is connected to the power supply.
Failure to comply with this precaution can result in irreparable damage to the electronics.
Risk of electric shock. Connect the protective ground to the ground terminal on the housing
before the power supply is applied.
You may only connect the sensor to the transmitter with the same serial number. Communication
errors can occur if this is not observed when connecting the devices.
1. Remove the connection compartment cover (d) of the transmitter and sensor housing.
2. Feed the connecting cable (e) through the appropriate cable runs.
3. Establish the connections between sensor and transmitter in accordance with the wiring
diagram (see 21 or wiring diagram in screw cap).
4. Screw the connection compartment cover (d) back onto the sensor and transmitter housing.
a0003681
Fig. 21: Connecting the remote version
a Wall-mount housing: non-hazardous area and ATEX II3G / zone 2 see separate "Ex documentation"
b Wall-mount housing: ATEX II2G / Zone 1 /FM/CSA see separate "Ex documentation"
c Remote version, flanged version
d Cover of the connection compartment or connection housing
e Connecting cable
Terminal No.: 4/5 = gray; 6/7 = green; 8 = yellow; 9/10 = pink; 11/12 = white; 41/42 = brown
S1 S1 S2 S2 GNDTMTM TT TT
+ + + +
+ + + +
S1 S1 S2 S2 GNDTMTM TT TT
a b
c
d
d
d
e
4 5 6 7 8 9 10 11 12 41 42
4 5 6 7 8 9 10 11 12 41 42
Proline Promass 83 Wiring
Endress+Hauser 27
4.1.2 Cable specification, connecting cable
The specifications of the cable connecting the transmitter and the sensor of the remote version are
as follows:
6 0.38 mm
2
PVC cable with common shield and individually shielded cores
Conductor resistance: s 50 O/km
Capacitance core/shield: s 420 pF/m
Cable length: max. 20 m (65 ft)
Permanent operating temperature: max. +105 C (+221 F)
!
Note!
The cable must be installed securely, to prevents movement.
4.2 Connecting the measuring unit
4.2.1 Transmitter connection
#
Warning!
Risk of electric shock. Switch off the power supply before opening the device. Do not install or
wire the device while it is connected to the power supply. Failure to comply with this precaution
can result in irreparable damage to the electronics.
Risk of electric shock. Connect the protective ground to the ground terminal on the housing
before the power supply is applied (not required for galvanically isolated power supply).
Compare the specifications on the nameplate with the local supply voltage and frequency.
The national regulations governing the installation of electrical equipment also apply.
1. Unscrew the connection compartment cover (f) from the transmitter housing.
2. Feed the power supply cable (a) and the signal cable (b) through the appropriate cable entries.
3. Perform wiring:
Wiring diagram (aluminum housing) 22
Wiring diagram (stainless steel housing) 23
Wiring diagram (wall-mount housing) 24
Terminal assignment 29
4. Screw the cover of the connection compartment (f) back onto the transmitter housing.
a0004582
Fig. 22: Connecting the transmitter (aluminum field housing). Cable cross-section: max. 2.5 mm
2
a Cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
b Signal cable: Terminals Nos. 2027 29
c Ground terminal for protective ground
d Ground terminal for signal cable shield
e Service adapter for connecting service interface FXA193 (FieldCheck, FieldCare)
f Cover of the connection compartment
g Securing clamp
b
b
c
d
a
a
2
1
27
25
23
21
+26
+24
+22
+20
L1 (L+)
N (L-)
g
f
e
Wiring Proline Promass 83
28 Endress+Hauser
a0004584
Fig. 23: Connecting the transmitter (stainless steel field housing); cable cross-section: max. 2.5 mm
2
a Cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
b Signal cable: Terminals Nos. 2027 29
c Ground terminal for protective ground
d Ground terminal for signal cable shield
e Service adapter for connecting service interface FXA193 (FieldCheck, FieldCare)
f Cover of the connection compartment
a0001135
Fig. 24: Connecting the transmitter (wall-mount housing); cable cross-section: max. 2.5 mm
2
a Cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
TerminalNo. 1: L1 for AC, L+ for DC
TerminalNo. 2: N for AC, L- for DC
b Signal cable: Terminals Nos. 2027 29
c Ground terminal for protective ground
d Ground terminal for signal cable shield
e Service adapter for connecting service interface FXA193 (FieldCheck, FieldCare)
f Cover of the connection compartment
b
c
d
a
2
1 L1 (L+)
N (L-)
f
b
a
e
27
25
23
21
+ 26
+ 24
+ 22
+ 20
1 2
c d
e
a
a
b
b
f
+
22
23
+
20
21
+
24
25
+
26
27
L1 (L+)
N (L-)
Proline Promass 83 Wiring
Endress+Hauser 29
4.2.2 Terminal assignment
Electrical values for:
Inputs 103
Outputs 106
Order characteristic
for "inputs/outputs"
Terminal No. (inputs/outputs)
20 (+) / 21 () 22 (+) / 23 () 24 (+) / 25 () 26 (+) / 27 ()
Fixed communication boards (permanent assignment)
A - - Frequency output Current output, HART
B Relay output Relay output Frequency output Current output, HART
R - - Current output 2,
Ex i, active
Current output 1, Ex i,
active, HART
S - -
Frequency output,
Ex i, passive
Current output, Ex i,
active, HART
T - -
Frequency output,
Ex i, passive
Current output, Ex i,
passive, HART
U - - Current output 2,
Ex i, passive
Current output 1, Ex i,
passive, HART
Flexible communication boards
C Relay output 2 Relay output 1 Frequency output Current output, HART
D Status input Relay output Frequency output Current output, HART
E Status input Relay output Current output 2 Current output 1, HART
L Status input Relay output 2 Relay output 1 Current output, HART
M Status input Frequency output 2 Frequency output 1 Current output, HART
W Relay output Current output 3 Current output 2 Current output 1, HART
0 Status input Current output 3 Current output 2 Current output 1, HART
2 Relay output Current output 2 Frequency output Current output 1, HART
3 Current input Relay output Current output 2 Current output 1, HART
4 Current input Relay output Frequency output Current output, HART
5 Status input Current input Frequency output Current output, HART
6 Status input Current input Current output 2 Current output, HART
Wiring Proline Promass 83
30 Endress+Hauser
4.2.3 HART connection
Users have the following connection options at their disposal:
Direct connection to transmitter by means of terminals 26(+) / 27()
Connection by means of the 4 to 20 mA circuit
!
Note!
The measuring circuit's minimum load must be at least 250 O.
The CURRENT SPAN function must be set to "4-20 mA" (individual options see device function).
See also the documentation issued by the HART Communication Foundation, and in particular
HCF LIT 20: "HART, a technical summary".
Connection of the HART handheld communicator
See also the documentation issued by the HART Communication Foundation, and in particular
HCF LIT 20: "HART, a technical summary".
a0004586
Fig. 25: Electrical connection of HART handheld Field Xpert SFX100
1 HART handheld Field Xpert SFX100
2 Auxiliary energy
3 Shielding
4 Other devices or PLC with passive input
Connection of a PC with an operating software
In order to connect a PC with operating software (e.g. FieldCare), a HART modem
(e.g. Commubox FXA195) is needed.
a0004592
Fig. 26: Electrical connection of a PC with operating software
1 PC with operating software
2 Auxiliary energy
3 Shielding
4 Other switching units or PLC with passive input
5 HART modem, e.g. Commubox FXA195
+26
-27
4
2
W 250
1
3
+26
W 250
27
1
2
3
5
4
Proline Promass 83 Wiring
Endress+Hauser 31
4.3 Degree of protection
The measuring device fulfill all the requirements for IP 67.
Compliance with the following points is mandatory following installation in the field or servicing,
in order to ensure that IP 67 protection is maintained:
The housing seals must be clean and undamaged when inserted into their grooves.
The seals must be dried, cleaned or replaced if necessary.
The threaded fasteners and screw covers must be firmly tightened.
The cables used for connection must be of the specified outside diameter 107, cable entries.
The cable entries must be firmly tighten (point a 27).
The cable must loop down in front of the cable entry ("water trap") (point b 27).
This arrangement prevents moisture penetrating the entry.
!
Note!
The cable entries may not be point up.
a0001914
Fig. 27: Installation instructions, cable entries
Remove all unused cable entries and insert plugs instead.
Do not remove the grommet from the cable entry.
"
Caution!
Do not loosen the screws of the sensor housing, as otherwise the degree of protection guaranteed
by Endress+Hauser no longer applies.
a b
Wiring Proline Promass 83
32 Endress+Hauser
4.4 Post-connection check
Perform the following checks after completing electrical installation of the measuring device:
Device condition and specifications Notes
Are cables or the device damaged (visual inspection)? -
Electrical connection Notes
Does the supply voltage match the specifications on the nameplate? 85 to 260 V AC (45 to 65 Hz)
20 to 55 V AC (45 to 65 Hz)
16 to 62 V DC
Do the cables comply with the specifications? 27
Do the cables have adequate strain relief? -
Cables correctly segregated by type?
Without loops and crossovers?
-
Are the power supply and signal cables correctly connected? See the wiring diagram inside
the cover of the terminal
compartment
Are all screw terminals firmly tightened? -
Are all cable entries installed, firmly tightened and correctly sealed?
Cables looped as "water traps"?
31
Are all housing covers installed and firmly tightened? -
Proline Promass 83 Operation
Endress+Hauser 33
5 Operation
5.1 Display and operating elements
The local display enables you to read all important parameters directly at the measuring point and
configure the device using the "Quick Setup" or the function matrix.
The display consists of four lines; this is where measured values and/or status variables (direction
of flow, empty pipe, bar graph, etc.) are displayed. You can change the assignment of display lines
to different variables to suit your needs and preferences ( see the "Description of Device
Functions" manual).
a0001172
Fig. 28: Display and operating elements
1 Liquid crystal display
The backlit, four-line liquid crystal display shows measured values, dialog texts, fault messages and notice
messages. HOME position (operating mode) is the term given to the display during normal operation.
Readings displayed
2 Optical sensors for "Touch Control"
3 Plus/minus keys
HOME position Direct access to totalizer values and actual values of inputs/outputs
Enter numerical values, select parameters
Select different blocks, groups and function groups within the function matrix
Press the +/ keys (X) simultaneously to trigger the following functions::
Exit the function matrix step by step HOME position
Press and hold down +/ keys for longer than 3 seconds Return directly to HOME position
Cancel data entry
4 Enter key
HOME position Entry into the function matrix
Save the numerical values you input or settings you change
+24.502
+1863.97
x
y
50 +50
%
v
v
3 S
Esc
E +
-
1
2
3 4
x
y
+24.502
+1863.97
x
y
50 +50
%
v
v
3 S
x
y
Operation Proline Promass 83
34 Endress+Hauser
5.1.1 Readings displayed (operation mode)
The display area consists of three lines in all; this is where measured values are displayed, and/or
status variables (direction of flow, bar graph, etc.). You can change the assignment of display lines
to different variables to suit your needs and preferences ( see the "Description of Device
Functions" manual).
Multiplex mode:
A maximum of two different display variables can be assigned to each line. Variables multiplexed in
this way alternate every 10 seconds on the display.
Error messages:
Display and presentation of system/process errors 40
a0001173
Fig. 29: Typical display for normal operating mode (HOME position)
1 Main line: shows main measured values
2 Additional line: shows additional measured variables and status variables
3 Information line: shows additional information on the measured variables and status variables, e.g. bargraph display
4 "Info icons" field: icons representing additional information on the measured values are shown in this
field 35.
5 "Measured values" field: the current measured values appear in this field.
6 Unit of measure" field: the units of measure and time defined for the current measured values appear in this field.
5.1.2 Additional display functions
Depending on the order option, the local display has different display functions
(F-CHIP 81).
Device without batching software:
From HOME position, use the P keys to open an "Info Menu" containing the following information:
Totalizer (including overflow)
Actual values or states of the configured inputs/outputs
Device TAG number (user-definable)
P Scan of individual values within the Info Menu
X (Esc key) Back to HOME position
Device with batching software:
On measuring instruments with installed batching software (F-Chip*) and a suitably configured
display line, you can carry out filling processes directly using the local display. You will find a
detailed description 37.
1
4 5 6
2
3
+24.502
+1863.97
x
x
y
y
50 +50
%
v
v
3 S
Proline Promass 83 Operation
Endress+Hauser 35
5.1.3 Icons
The icons which appear in the field on the left make it easier to read and recognize measured
variables, device status, and error messages.
Icon Meaning Icon Meaning
S System error P Process error
$ Fault message
(with effect on outputs)
! Notice message
(without effect on outputs)
| 1 to n Current output 1 to n P 1 to n Pulse output 1 to n
F 1 to n Frequency output S 1 to n Status output/relay output 1 to n
E 1 to n Totalizer 1 to n
a0001187
Status input
a0001181
Measuring mode;
PULSATING FLOW
a0001182
Measuring mode;
SYMMETRY (bidirectional)
a0001183
Measuring mode;
STANDARD
a0001184
Counting mode, totalizer;
BALANCE (forward + reverse flow)
a0001185
Counting mode, totalizer;
forward
a0001186
Counting mode, totalizer;
reverse
a0001188
Volume flow
a0001189
Target volume flow
a0001190
Target corrected volume flow
a0001191
Carrier volume flow
a0001192
Carrier corrected volume flow
a0001193
% Target volume flow
a0001194
% Carrier volume flow
a0001195
Mass flow
a0001196
Target mass flow
a0001197
% Target mass flow
a0001198
Carrier mass flow
a0001199
% Carrier mass flow
a0001200
Fluid density
a0001208
Reference density
Operation Proline Promass 83
36 Endress+Hauser
a0001201
Batching quantity upwards
a0001202
Batching quantity downwards
a0001203
Batch quantity
a0001204
Total batching quantity
a0001205
Batch counter (x times)
a0001207
Fluid temperature
a0001209
Current input
a0001206
Remote configuration
Active device operation via:
HART, e.g. FieldCare, DXR 375
Icon Meaning Icon Meaning
Proline Promass 83 Operation
Endress+Hauser 37
5.1.4 Controlling the batching processes using the local display
Filling processes can be controlled directly by means of the local display with the aid of the optional
"(Batching)" software package (F-CHIP, accessories 83). Therefore, the device can be fully
deployed in the field as a "batch controller".
Procedure:
1. Configure all the required batching functions and assign the lower display info line (=
BATCHING KEYS) using the "Batch" Quick Setup menu ( 60) or using the function
matrix ( 38).
The following "softkeys" then appear on the bottom line of the local display 30:
START = left display key (S)
PRESET = middle display key (O)
MATRIX = right display key (F)
2. Press the "PRESET (O)" key. Various batching process functions requiring configuration will
now appear on the display:
3. After exiting the PRESET menu, you can now start the batching process by pressing "START
(S)". New softkeys (STOP / HOLD or GO ON) now appear on the display. You can use these
to interrupt, continue or stop the batching process at any time. 30
STOP (S) Stops batching process
HOLD (O) Interrupts batching process (softkey changes to "GO ON")
GO ON (O) Continues batching process (softkey changes to "HOLD")
After the batch quantity is reached, the "START" or "PRESET" softkeys reappear on the display.
a0004386
Fig. 30: Controlling batching processes using the local display (softkeys)
"PRESET" Initial settings for the batching process
No. Function Configuration
7200 BATCH SELECTOR OS Select the batching liquid (BATCH #1 to 6)
7203 BATCH QUANTITY If the "ACCESS CUSTOMER" option was selected for the "PRESET
batch quantity" prompt in the "Batching" Quick Setup, the batching
quantity can be altered via the local display. If the "LOCKED" option
was selected, the batching quantity can only be read and cannot be
altered until the private code has been entered.
7265 RESET TOTAL BATCH SUM/
COUNTER
Resets the batching quantity counter or the total batching quantity to
"0".
STOP GO ON MATRIX
+2.5 l
0.0 l
+2.5 l
0.0 l 0.0 l
+
-
+2.5 l
0.0 l
START PRESET MATRIX
STOP HOLD MATRIX
E
Operation Proline Promass 83
38 Endress+Hauser
5.2 Brief operating instructions to the function matrix
!
Note!
See the general notes 39
Function descriptions see the "Description of Device Functions" manual
1. HOME position F Entry into the function matrix
2. Select a block (e.g. OUTPUTS)
3. Select a group (e.g. CURRENT OUTPUT 1)
4. Select a function group (e.g. SETTINGS)
5. Select a function (e.g. TIME CONSTANT)
Change parameter / enter numerical values:
P Select or enter enable code, parameters, numerical values
F Save your entries
6. Exit the function matrix:
Press and hold down Esc key (X) for longer than 3 seconds HOME position
Repeatedly press Esc key (X) Return step by step to HOME position
a0001210
Fig. 31: Selecting functions and configuring parameters (function matrix)
- + E
Esc
>3s
E
E
E
E
E E E E E E E
+
E
+
Esc
+ + +
+
Esc
m
o p q
r
n
+
Proline Promass 83 Operation
Endress+Hauser 39
5.2.1 General notes
The Quick Setup menu contains the default settings that are adequate for commissioning. Complex
measuring operations on the other hand necessitate additional functions that you can configure as
necessary and customize to suit your process parameters. The function matrix, therefore, comprises
a multiplicity of additional functions which, for the sake of clarity, are arranged on a number of
menu levels (blocks, groups, and function groups).
Comply with the following instructions when configuring functions:
You select functions as described on 38.
Each cell in the function matrix is identified by a numerical or letter code on the display.
You can switch off certain functions (OFF). If you do so, related functions in other function groups
will no longer be displayed.
Certain functions prompt you to confirm your data entries. Press OS to select "SURE [ YES ]" and
press F to confirm. This saves your setting or starts a function, as applicable.
Return to the HOME position is automatic if no key is pressed for 5 minutes.
Programming mode is disabled automatically if you do not press a key within 60 seconds
following automatic return to the HOME position.
"
Caution!
All functions are described in detail, as is the function matrix itself, in the "Description of Device
Functions" manual, which is a separate part of these Operating Instructions.
!
Note!
The transmitter continues to measure while data entry is in progress, i.e. the current measured
values are output via the signal outputs in the normal way.
If the supply voltage fails all preset and parameterized values remain safely stored in the EEPROM.
5.2.2 Enabling the programming mode
The function matrix can be disabled. Disabling the function matrix rules out the possibility of
inadvertent changes to device functions, numerical values or factory settings. A numerical code
(factory setting = 83) has to be entered before settings can be changed.
If you use a code number of your choice, you exclude the possibility of unauthorized persons
accessing data ( see the "Description of Device Functions" manual).
Comply with the following instructions when entering codes:
If programming is disabled and the P operating elements are pressed in any function, a prompt
for the code automatically appears on the display.
If "0" is entered as the customer's code, programming is always enabled!
The Endress+Hauser service organization can be of assistance if you mislay your personal code.
"
Caution!
Changing certain parameters such as all sensor characteristics, for example, influences numerous
functions of the entire measuring system, particularly measuring accuracy.
There is no need to change these parameters under normal circumstances and consequently, they
are protected by a special code known only to the Endress+Hauser service organization. Please
contact Endress+Hauser if you have any questions.
5.2.3 Disabling the programming mode
Programming mode is disabled if you do not press an operating element within 60 seconds following
automatic return to the HOME position.
You can also disable programming in the ACCESS CODE function by entering any number (other
than the customer's code).
Operation Proline Promass 83
40 Endress+Hauser
5.3 Error messages
5.3.1 Type of error
Errors that occur during commissioning or measuring are displayed immediately. If two or more
system or process errors are present, the error with the highest priority is the one shown on the
display.
The measuring system distinguishes between two types of error:
System error:
Includes all device errors, e.g. communication errors, hardware errors, etc. 86
Process error:
Includes all application errors, e.g. fluid not homogeneous, etc. 91
a0001211
Fig. 32: Error messages on the display (example)
1 Error type: P = process error, S = system error
2 Error message type: $ = fault message, ! = notice message
3 Error designation: e.g. "FLUID INHOM." = fluid is not homogeneous
4 Error number: e.g. #702
5 Duration of most recent error occurrence (hours: minutes: seconds)
5.3.2 Error message type
Users have the option of weighting system and process errors differently, by defining them as Fault
messages or Notice messages. You can define messages in this way with the aid of the function
matrix (see the "Description of Device Functions" manual).
Serious system errors, e.g. module defects, are always identified and classed as "fault messages" by
the measuring device.
Notice message (!)
The error in question has no effect on the current measuring operation and the outputs of the
measuring device.
Displayed as Exclamation mark (!), type of error (S: system error, P: process error)
Fault message ( $)
The error in question interrupts or stops the current measuring operation and has an immediate
effect on the outputs. The response of the outputs (failsafe mode) can be defined by means of
functions in the function matrix. 94
Displayed as Lightning flash ( $ ), type of error (S: system error, P: process error)
!
Note!
Error conditions can be output via the relay outputs.
If an error message occurs, an upper or lower signal level for the breakdown information
according to NAMUR 43 can be output via the current output.
1
2 4 5 3
+24.502
XXXXXXXXXX
#000 00: 00: 05
P
+24.502
Proline Promass 83 Operation
Endress+Hauser 41
5.3.3 Confirming error messages
For the sake of plant and process safety, the measuring device can be configured in such a way that
fault messages displayed ($) always have to be rectified and acknowledged locally by pressing F.
Only then do the error messages disappear from the display.
This option can be switched on or off by means of the "ACKNOWLEDGE FAULT MESSAGES"
function (see the "Description of Device Functions" manual).
!
Note!
Fault messages ($) can also be reset and confirmed via the status input.
Notice messages (!) do not require acknowledgment. Note, however, that they remain visible
until the cause of the error has been rectified.
5.4 Communication
In addition to local operation, the measuring device can be configured and measured values can be
obtained by means of the HART protocol. Digital communication takes place using the 4-20 mA
current output HART. 30
The HART protocol allows the transfer of measuring and device data between the HART master and
the field devices for configuration and diagnostics purposes. The HART master, e.g. a handheld
terminal or PC-based operating programs (such as FieldCare), require device description (DD) files
which are used to access all the information in a HART device. Information is exclusively transferred
using so-called "commands". There are three different command groups:
There are three different command groups:
Universal Commands
Universal commands are supported and used by all HART devices. These are associated with the
following functionalities for example:
Recognizing HART devices
Reading digital measured values (volume flow, totalizer, etc.)
Common practice commands:
Common practice commands offer functions which are supported and can be executed by most
but not all field devices.
Device-specific commands:
These commands allow access to device-specific functions which are not HART standard. Such
commands access individual field device information, amongst other things, such as empty/full
pipe calibration values, low flow cut off settings, etc.
!
Note!
The measuring device has access to all three command classes.
List of all "Universal Commands" and "Common Practice Commands": 45
Operation Proline Promass 83
42 Endress+Hauser
5.4.1 Operating options
For the complete operation of the measuring device, including device-specific commands, there are
DD files available to the user to provide the following operating aids and programs:
!
Note!
In the CURRENT RANGE function (current output 1), the HART protocol demands the setting
"4-20 mA HART" or "4-20 mA (25 mA) HART".
HART write protection can be disabled or enabled by means of a jumper on the I/O board.
53
HART handheld terminal Field Xpert
Selecting device functions with a HART Communicator is a process involving a number of
menu levels and a special HART function matrix.
The HART manual in the carrying case of the HART Communicator contains more detailed
information on the device.
Operating program "FieldCare"
FieldCare is Endress+Hausers FDT-based plant asset management tool and allows the configuration
and diagnosis of intelligent field devices. By using status information, you also have a simple but
effective tool for monitoring devices. The Proline flowmeters are accessed via a HART interface
FXA195 or via the service interface FXA193.
Operating program "SIMATIC PDM" (Siemens)
SIMATIC PDM is a standardized, manufacturer-independent tool for the operation, configuration,
maintenance and diagnosis of intelligent field devices.
Operating program "AMS" (Emerson Process Management)
AMS (Asset Management Solutions): program for operating and configuring devices
Proline Promass 83 Operation
Endress+Hauser 43
5.4.2 Current device description files
The following table illustrates the suitable device description file for the operating tool in question
and then indicates where these can be obtained.
HART protocol:
Valid for software: 3.01.00 Function DEVICE SOFTWARE
Device data HART
Manufacturer ID:
Device ID:
11
hex
(ENDRESS+HAUSER)
51
hex
Function MANUFACTURER ID
Function DEVICE ID
HART version data: Device Revision 9 / DD Revision 1
Software release: 01.2010
Operating program: Sources for obtaining device descriptions:
Field Xpert handheld terminal Use update function of handheld terminal
FieldCare / DTM www.endress.com Download-Area
CDROM (Endress+Hauser order number 56004088)
DVD (Endress+Hauser order number 70100690)
AMS www.endress.com Download-Area
SIMATIC PDM www.endress.com Download-Area
Tester/simulator: Sources for obtaining device descriptions:
Fieldcheck Update by means of FieldCare via flow device FXA 193/291 DTM in Fieldflash
Module
Operation Proline Promass 83
44 Endress+Hauser
5.4.3 Device and process variables
Device variables:
The following device variables are available using the HART protocol:
Process variables:
At the factory, the process variables are assigned to the following device variables:
Primary process variable (PV) Mass flow
Second process variable (SV) Totalizer 1
Third process variable (TV) Density
Fourth process variable (FV) Temperature
!
Note!
You can set or change the assignment of device variables to process variables using Command 51.
48
Code (decimal) Device variable Code (decimal) Device variable
0 OFF (unassigned) 26 PLATO
2 Mass flow 27 BALLING
5 Volume flow 28 BRIX
6 Corrected volume flow 29 Other
7 Density 52 Batch up
8 Reference density 53 Batch down
9 Temperature 58 Mass flow deviation
12 Target mass flow 59 Density deviation
13 % Target mass flow 60 Reference density deviation
14 Target volume flow 61 Temperature deviation
15 % Target volume flow 62 Tube damping deviation
16 Target corrected volume flow 63 Electrodyn. sensor deviation
17 Carrier mass flow 64 Dynamic viscosity
18 % Carrier mass flow 65 Kinematic viscosity
19 Carrier volume flow 81 Temp. comp. dyn. viscosity
20 % carrier volume flow 82 Temp. comp. kin. viscosity
21 Carrier corrected volume flow 86 Operating frequency fluctuation
22 %-BLACK LIQUOR 87 Tube damping fluctuation
23 BAUME >1kg/l 250 Totalizer 1
24 BAUME <1kg/l 251 Totalizer 2
25 API 252 Totalizer 3
Proline Promass 83 Operation
Endress+Hauser 45
5.4.4 Universal / Common practice HART commands
The following table contains all the universal commands supported by the device.
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Universal Commands
0 Read unique device identifier
Access type = read
none Device identification delivers information on the device
and the manufacturer. It cannot be changed.
The response consists of a 12-byte device ID:
Byte 0: Fixed value 254
Byte 1: Manufacturer ID, 17 = E+H
Byte 2: Device type ID, e.g. 81 = Promass 83
or 80 = Promass 80
Byte 3: Number of preambles
Byte 4: Universal commands rev. no.
Byte 5: Device-spec. commands rev. no.
Byte 6: Software revision
Byte 7: Hardware revision
Byte 8: Additional device information
Byte 9-11: Device identification
1 Read primary process variable
Access type = read
none Byte 0: HART unit code of the primary process
variable
Bytes 1-4: Primary process variable
Factory setting:
Primary process variable = Mass flow
!
Note!
You can set the assignment of device variables to
process variables using Command 51.
Manufacturer-specific units are represented using the
HART unit code "240".
2 Read the primary process variable as
current in mA and percentage of the
set measuring range
Access type = read
none Bytes 0-3: Actual current of the primary process
variable in mA
Bytes 4-7: Percentage of the set measuring range
Factory setting:
Primary process variable = Mass flow
!
Note!
You can set the assignment of device variables to process
variables using Command 51.
3 Read the primary process variable as
current in mA and four (preset
using Command 51) dynamic
process variables
Access type = read
none 24 bytes are sent as a response:
Bytes 0-3: Primary process variable current in mA
Byte 4: HART unit code of the primary process
variable
Bytes 5-8: Primary process variable
Byte 9: HART unit code of the second process variable
Bytes 10-13: Second process variable
Byte 14: HART unit code of the third process variable
Bytes 15-18: Third process variable
Byte 19: HART unit code of the fourth process
variable
Bytes 20-23: Fourth process variable
Factory setting:
Primary process variable = Mass flow
Second process variable = Totalizer 1
Third process variable = Density
Fourth process variable = Temperature
!
Note!
You can set the assignment of device variables to
process variables using Command 51.
Manufacturer-specific units are represented using the
HART unit code "240".
Operation Proline Promass 83
46 Endress+Hauser
6 Set HART shortform address
Access type = write
Byte 0: desired address (0 to 15)
Factory setting:
0
!
Note!
With an address >0 (multidrop mode), the current
output of the primary process variable is set to 4 mA.
Byte 0: active address
11 Read unique device identification
using the TAG (measuring point
designation)
Access type = read
Bytes 0-5: TAG Device identification delivers information on the device
and the manufacturer. It cannot be changed.
The response consists of a 12-byte device ID if the given
TAG agrees with the one saved in the device:
Byte 0: Fixed value 254
Byte 1: Manufacturer ID, 17 = E+H
Byte 2: Device type ID, 81 = Promass 83
or 80 = Promass 80
Byte 3: Number of preambles
Byte 4: Universal commands rev. no.
Byte 5: Device-spec. commands rev. no.
Byte 6: Software revision
Byte 7: Hardware revision
Byte 8: Additional device information
Byte 9-11: Device identification
12 Read user message
Access type = read
none Bytes 0-24: User message
!
Note!
You can write the user message using Command 17.
13 Read TAG, descriptor and date
Access type = read
none Byte 0-5: TAG
Bytes 6-17: Descriptor
Byte 18-20: Date
!
Note!
You can write the TAG, descriptor and date using
Command 18.
14 Read sensor information on primary
process variable
none Bytes 0-2: Sensor serial number
Byte 3: HART unit code of sensor limits and
measuring range of the primary process variable
Bytes 4-7: Upper sensor limit
Bytes 8-11: Lower sensor limit
Bytes 12-15: Minimum span
!
Note!
The data relate to the primary process variable (=
Mass flow).
Manufacturer-specific units are represented using the
HART unit code "240".
15 Read output information of primary
process variable
Access type = read
none Byte 0: Alarm selection ID
Byte 1: Transfer function ID
Byte 2: HART unit code for the set measuring range of
the primary process variable
Bytes 3-6: Upper range, value for 20 mA
Bytes 7-10: Start of measuring range, value for 4 mA
Bytes 11-14: Attenuation constant in [s]
Byte 15: Write protection ID
Byte 16: OEM dealer ID, 17 = E+H
Factory setting:
Primary process variable = Mass flow
!
Note!
You can set the assignment of device variables to
process variables using Command 51.
Manufacturer-specific units are represented using the
HART unit code "240".
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Proline Promass 83 Operation
Endress+Hauser 47
The following table contains all the common practice commands supported by the device.
16 @Read the device production
number
Access type = read
none Bytes 0-2: Production number
17 Write user message
Access = write
You can save any 32-character long text in the device
under this parameter:
Bytes 0-23: Desired user message
Displays the current user message in the device:
Bytes 0-23: Current user message in the device
18 Write TAG, descriptor and date
Access = write
With this parameter, you can store an 8 character TAG, a
16 character descriptor and a date:
Bytes 0-5: TAG)
Bytes 6-17: Descriptor
Byte 18-20: Date
Displays the current information in the device:
Bytes 0-5: TAG
Bytes 6-17: Descriptor
Byte 18-20: Date
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Common Practice Commands")
34 Write damping value for primary
process variable
Access = write
Bytes 0-3: Damping value of the primary process variable
in seconds
Factory setting:
Primary process variable = Mass flow
Displays the current damping value in the device:
Bytes 0-3: Damping value in seconds
35 Write measuring range of primary
process variable
Access = write
Write the desired measuring range:
Byte 0: HART unit code of the primary process
variable
Bytes 1-4: Upper range, value for 20 mA
Bytes 5-8: Start of measuring range, value for 4 mA
Factory setting:
Primary process variable = Mass flow
!
Note!
Die You can set the assignment of device variables to
process variables using Command 51.
If the HART unit code is not the correct one for the
process variable, the device will continue with the last
valid unit.
The currently set measuring range is displayed as a
response:
Byte 0: HART unit code for the set measuring range of
the primary process variable
Bytes 1-4: Upper range, value for 20 mA
Bytes 5-8: Start of measuring range, value for 4 mA
!
Note!
Manufacturer-specific units are represented using the
HART unit code "240".
38 Device status reset (Configuration
changed)
Access = write
none none
40 Simulate output current of primary
process variable
Access = write
Simulation of the desired output current of the primary
process variable.
An entry value of 0 exits the simulation mode:
Byte 0-3: Output current in mA
Factory setting:
Primary process variable = Mass flow
!
Note!
You can set the assignment of device variables to process
variables with Command 51.
The momentary output current of the primary process
variable is displayed as a response:
Byte 0-3: Output current in mA
42 Perform master reset
Access = write
none none
Operation Proline Promass 83
48 Endress+Hauser
44 Write unit of primary process
variable
Access = write
Set unit of primary process variable.
Only unit which are suitable for the process variable are
transferred to the device:
Byte 0: HART unit code
Factory setting:
Primary process variable = Mass flow
!
Note!
If the written HART unit code is not the correct one
for the process variable, the device will continue with
the last valid unit.
If you change the unit of the primary process variable,
this has no impact on the system units.
The current unit code of the primary process variable is
displayed as a response:
Byte 0: HART unit code
!
Note!
Manufacturer-specific units are represented using the
HART unit code "240".
48 Read additional device status
Access = read
none The device status is displayed in extended form as the
response:
Coding: see table 50
50 Read assignment of the device
variables to the four process
variables
Access = read
none Display of the current variable assignment of the process
variables:
Byte 0: Device variable code to the primary process
variable
Byte 1: Device variable code to the second process
variable
Byte 2: Device variable code to the third process
variable
Byte 3: Device variable code to the fourth process
variable
Factory setting:
Primary process variable: Code 1 for mass flow
Second process variable: Code 250 for totalizer 1
Third process variable: Code 7 for density
Fourth process variable: Code 9 for temperature
!
Note!
You can set the assignment of device variables to process
variables with Command 51.
51 Write assignments of the device
variables to the four process
variables
Access = write
Setting of the device variables to the four process
variables:
Byte 0: Device variable code to the primary process
variable
Byte 1: Device variable code to the second process
variable
Byte 2: Device variable code to the third process
variable
Byte 3: Device variable code to the fourth process
variable
Code of the supported device variables:
See data 44
Factory setting:
Primary process variable = Mass flow
Second process variable = Totalizer 1
Third process variable = Density
Fourth process variable = Temperature
The variable assignment of the process variables is
displayed as a response:
Byte 0: Device variable code to the primary process
variable
Byte 1: Device variable code to the second process
variable
Byte 2: Device variable code to the third process
variable
Byte 3: Device variable code to the fourth process
variable
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Proline Promass 83 Operation
Endress+Hauser 49
53 Write device variable unit
Access = write
This command sets the unit of the given device variables.
Only those units which suit the device variable are
transferred:
Byte 0: Device variable code
Byte 1: HART unit code
Code of the supported device variables:
See data 44
!
Note!
If the written unit is not the correct one for the device
variable, the device will continue with the last valid
unit.
If you change the unit of the device variable, this has
no impact on the system units.
The current unit of the device variables is displayed in
the device as a response:
Byte 0: Device variable code
Byte 1: HART unit code
!
Note!
Manufacturer-specific units are represented using the
HART unit code "240".
59 Write number of preambles in
response message
Access = write
This parameter sets the number of preambles which are
inserted in the response messages:
Byte 0: Number of preambles (2 to 20)
As a response, the current number of the preambles is
displayed in the response message:
Byte 0: Number of preambles
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
(numeric data in decimal form)
Operation Proline Promass 83
50 Endress+Hauser
5.4.5 Device status / Error messages
You can read the extended device status, in this case, current error messages, via Command "48".
The command delivers information which are partly coded in bits (see table below).
!
Note!
Explanation of the device status and error messages and their elimination Page 84 ff.
Byte-bit Error No. Short error description Page 84 ff.
0-0 001 Serious device error
0-1 011 Measuring amplifier has faulty EEPROM
0-2 012 Error when accessing data of the measuring amplifier EEPROM
1-1 031 S-DAT: Defective or missing
1-2 032 S-DAT: Error accessing saved values
1-3 041 T-DAT: Defective or missing
1-4 042 T-DAT: Error accessing saved values
1-5 051 I/O board and the amplifier board are not compatible.
3-3 111 Totalizer checksum error
3-4 121 I/O board and the amplifier board (software versions) are not compatible.
3-6 205 T-DAT: Data download not successful
3-7 206 T-DAT: Data upload not successful
4-3 251 Internal communication fault on the amplifier board.
4-4 261 No data reception between amplifier and I/O board
5-7 339
Flow buffer:
The temporarily buffered flow portions (measuring mode for pulsating flow) could
not be cleared or output within 60 seconds.
6-0 340
6-1 341
6-2 342
6-3 343
Frequency buffer:
The temporarily buffered flow portions (measuring mode for pulsating flow) could
not be cleared or output within 60 seconds.
6-4 344
6-5 345
6-6 346
6-7 347
Pulse buffer:
The temporarily buffered flow portions (measuring mode for pulsating flow) could
not be cleared or output within 60 seconds.
7-0 348
7-1 349
7-2 350
7-3 351
Current output:
The actual value for the flow lies outside the set limits.
7-4 352
7-5 353
7-6 354
7-7 355
Frequency output:
The actual value for the flow lies outside the set limits.
8-0 356
8-1 357
8-2 358
8-3 359
Pulse output:
Pulse output frequency is out of range.
8-4 360
8-5 361
8-6 362
Proline Promass 83 Operation
Endress+Hauser 51
9-0 379
The measuring tube oscillation frequency is outside the permitted range.
9-1 380
9-2 381
The temperature sensor on the measuring tube is likely defective.
9-3 382
9-4 383
The temperature sensor on the carrier tube is likely defective.
9-5 384
9-6 385
One of the measuring tube exciter coils (inlet or outlet) is likely defective. 9-7 386
10-0 387
10-1 388
Amplifier error 10-2 389
10-3 390
11-6 471 Max. permitted batching time has been exceeded.
11-7 472 Underbatching: the minimum quantity was not reached.
Overbatching: the maximum permitted batching quantity was exceeded.
12-0 473 The predefined batch quantity point was exceeded.
End of filling process approaching.
12-1 474 Maximum flow value entered is overshot.
12-7 501 New amplifier software version is loaded. Currently no other commands are
possible.
13-0 502 Upload and download of device files. Currently no other commands are possible.
13-2 571 Batching process in progress (valves are open)
13-3 572 Batching process has been stopped (valves are closed)
13-5 586 The fluid properties do not allow normal measuring operation.
13-6 587 Extreme process conditions exist.
The measuring system can therefore not be started.
13-7 588 Overdriving of the internal analog to digital converter.
A continuation of the measurement is no longer possible!
14-3 601 Positive zero return active
14-7 611
Simulation current output active
15-0 612
15-1 613
15-2 614
15-3 621
Simulation frequency output active
15-4 622
15-5 623
15-6 624
15-7 631
Simulation pulse output active
16-0 632
16-1 633
16-2 634
16-3 641
Simulation status output active
16-4 642
16-5 643
16-6 644
Byte-bit Error No. Short error description Page 84 ff.
Operation Proline Promass 83
52 Endress+Hauser
16-7 651
Simulation relay output active
17-0 652
17-1 653
17-2 654
17-3 661
Simulation current input active
17-4 662
17-5 663
17-6 664
17-7 671
Simulation status input active
18-0 672
18-1 673
18-2 674
18-3 691 Simulation of response to error (outputs) active
18-4 692 Simulation of volume flow active
19-0 700 The process fluid density is outside the upper or lower limit values set in the
"EPD" function
19-1 701 The maximum current value for the measuring tube exciter coils has been
reached,
since certain process fluid characteristics are extreme.
19-2 702 Frequency control is not stable, due to inhomogeneous fluid.
19-3 703 NOISE LIM. CH0
Overdriving of the internal analog to digital converter.
A continuation of the measurement is still possible!
19-4 704 NOISE LIM. CH1
Overdriving of the internal analog to digital converter.
A continuation of the measurement is still possible!
19-5 705 The electronics' measuring range will be exceeded. The mass flow is too high.
20-5 731 The zero point adjustment is not possible or has been canceled.
22-4 61 F-Chip is faulty or not plugged into the I/O board.
24-5 363 Current input:
The actual value for the current lies outside the set limits.
Byte-bit Error No. Short error description Page 84 ff.
Proline Promass 83 Operation
Endress+Hauser 53
5.4.6 Switching HART write protection on and off
A jumper on the I/O board provides the means of switching HART write protection on or off.
#
Warning!
Risk of electric shock. Exposed components carry dangerous voltages. Make sure that the power
supply is switched off before you remove the cover of the electronics compartment.
1. Switch off power supply.
2. Remove the I/O board 96
3. Switch HART write protection on or off, as applicable, by means of the jumper 33.
4. Installation of the I/O board is the reverse of the removal procedure.
a0001212
Fig. 33: Switching HART write protection on and off
1 Write protection OFF (default), that is: HART protocol unlocked
2 Write protection ON, that is: HART protocol locked
1
2
IN
P
U
T
/O
U
T
P
U
T
4
IN
P
U
T
/O
U
T
P
U
T
3
IN
P
U
T
/O
U
T
P
U
T
2
Commissioning Proline Promass 83
54 Endress+Hauser
6 Commissioning
6.1 Function check
Make sure that the following function checks have been performed successfully before switching on
the supply voltage for the measuring device:
Checklist for "Post-installation check" 25
Checklist for "Post-connection check" 32
6.2 Switching on the measuring device
Once the function check has been performed successfully, the device is operational and can be
switched on via the supply voltage. The device then performs internal test functions and the
following messages are shown on the local display:
Normal measuring mode commences as soon as startup completes.
Various measured value and/or status variables appear on the display (HOME position).
!
Note!
If startup fails, an error message indicating the cause is displayed.
PROMASS 83
START-UP
RUNNING
Startup message
PROMASS 83
DEVICE SOFTWARE
V XX.XX.XX
Current software version
CURRENT OUTPUT
FREQUENCY OUTPUT
RELAY
STATUS INPUT
List of installed input/output modules
SYSTEM OK
OPERATION
Beginning of normal measuring mode
Basic configuration
2002 DISPLAY DAMPING 1 s
3002 TOTALIZER MODE (DAA) BALANCE (Totalizer 1)
3002 TOTALIZER MODE (DAB) BALANCE (Totalizer 2)
3002 TOTALIZER MODE (DAC) BALANCE (Totalizer 3)
Signal type for "CURRENT OUTPUT 1 to n"
4004 MEASURING MODE PULSATING FLOW
4005 TIME CONSTANT 1 s
Signal type for "FREQ./PULSE OUTPUT 1 to n" (for FREQUENCY operating mode)
4206 MEASURING MODE PULSATING FLOW
4208 TIME CONSTANT 0 s
Signal type for "FREQ./PULSE OUTPUT 1 to n" (for PULSE operating mode)
4225 MEASURING MODE PULSATING FLOW
Other settings
8005 ALARM DELAY 0 s
6400 ASSIGN LOW FLOW CUTOFF MASS FLOW
6402 ON-VALUE LOW FLOW CUTOFF Setting depends on diameter:
DN 1 = 0.02 [kg/h] or [l/h]
DN 2 = 0.10 [kg/h] or [l/h]
DN 4 = 0.45 [kg/h] or [l/h]
DN 8 = 2.0 [kg/h] or [l/h]
DN 15 = 6.5 [kg/h] or [l/h]
DN 15 FB = 18 [kg/h] resp. [l/h]
DN 25 = 18 [kg/h] resp. [l/h]
DN 25 FB = 45 [kg/h] resp. [l/h]
DN 40 = 45 [kg/h] resp. [l/h]
DN 40 FB = 70 [kg/h] resp. [l/h]
DN 50 = 70 [kg/h] resp. [l/h]
DN 50 FB = 180 [kg/h] resp. [l/h]
DN 80 = 180 [kg/h] or [l/h]
DN 100 = 350 [kg/h] or [l/h]
DN 150 = 650 [kg/h] or [l/h]
DN 250 = 1800 [kg/h] or [l/h]
DN 350 = 3250 [kg/h] or [l/h]
FB = Full bore versions of Promass I
6403 OFF-VALUE LOW FLOW CUTOFF 50%
6404 PRESSURE SHOCK SUPPRESSION 0 s
!
Note!
Functions with a gray background are configured automatically (by the measuring system itself)
6400 ASSIGN LOW FLOW CUTOFF MASS FLOW
6402 ON-VALUE LOW FLOW CUTOFF See Table on 63
6403 OFF-VALUE LOW FLOW CUTOFF 50%
6603 FLOW DAMPING 0 seconds
6404 PRESSURE SHOCK SUPPRESSION 0 seconds
7200 BATCH SELECTOR BATCH #1
7201 BATCH NAME BATCH #1
7202 ASSIGN BATCH VARIABLE MASS
7203 BATCH QUANTITY 0
7204 FIXED CORRECTION QUANTITY 0
7205 CORRECTION MODE OFF
7208 BATCH STAGES 1
7209 INPUT FORMAT VALUE INPUT
4700 ASSIGN RELAY BATCH VALVE 1
4780 TERMINAL NUMBER Output (display only)
7220 OPEN VALVE 1 0% or 0 [unit]
7240 MAXIMUM BATCH TIME 0 seconds (= switched off)
7241 MINIMUM BATCH QUANTITY 0
7242 MAXIMUM BATCH QUANTITY 0
2200 ASSIGN (main line) BATCH NAME
2220 ASSIGN (Multiplex main line) OFF
2400 ASSIGN (additional line) BATCH DOWNWARDS
2420 ASSIGN (Multiplex additional line) OFF
2600 ASSIGN (information line) BATCHING KEYS
2620 ASSIGN (Multiplex information line) OFF
2000
PC software is part of the standard package and is used for
configuring, visualizing and archiving the data captured.
The mathematics channels which are optionally available
enable continuous monitoring of specific power consumption,
boiler efficiency and other parameters which are important for
efficient energy management.
RSG40 - ************
Accessories Proline Promass 83
84 Endress+Hauser
8.3 Communication-specific accessories
8.4 Service-specific accessories
Accessory Description Order code
HART Communicator
Field Xpert handheld
terminal
Handheld terminal for remote parameterization and for
obtaining measured values via the current output HART (4 to
20 mA).
Contact your Endress +Hauser representative for more
information.
SFX100 - *******
FXA195 The Commubox FXA195 connects intrinsically safe smart
transmitters with the HART protocol with the USB port of a
personal computer. This enables remote operation of the
transmitter with operating software (e.g. FieldCare). Power is
supplied to the Commubox via the USB port.
FXA195 - *
Accessory Description Order code
Applicator Software for selecting and sizing Endress+Hauser measuring
devices:
Calculation of all the necessary data for identifying the
optimum flowmeter: e.g. nominal diameter, pressure loss,
accuracy or process connections
Graphic illustration of the calculation results
Administration, documentation and access to all project-related
data and parameters over the entire life cycle of a project.
Applicator is available:
Via the Internet:
https://wapps.endress.com/applicator
On CD-ROM for local PC installation.
DXA80 *
W@M Life cycle management for your plant
W@M supports you with a wide range of software applications
over the entire process: from planning and procurement, to the
installation, commissioning and operation of the measuring
devices. All the relevant device information, such as the device
status, spare parts and device-specific documentation, is
available for every device over the entire life cycle.
The application already contains the data of your
Endress+Hauser device. Endress+Hauser also takes care of
maintaining and updating the data records.
W@M is available:
Via the Internet:
www.endress.com/lifecyclemanagement
On CD-ROM for local PC installation.
Fieldcheck Tester/simulator for testing flowmeters in the field.
When used in conjunction with the "FieldCare" software
package, test results can be imported into a database,
printed and used for official certification.
Contact your Endress+Hauser representative for more
information.
50098801
Proline Promass 83 Accessories
Endress+Hauser 85
FieldCare FieldCare is Endress+Hausers FDT-based plant asset
management tool and allows the configuration and diagnosis of
intelligent field devices. By using status information, you also
have a simple but effective tool for monitoring devices. The
Proline flowmeters are accessed via a service interface or via
the service interface FXA193.
Product page on the
Endress+Hauser website:
www.endress.com
FXA193 Service interface from the measuring device to the PC for
operation via FieldCare.
FXA193 *
Accessory Description Order code
Troubleshooting Proline Promass 83
86 Endress+Hauser
9 Troubleshooting
9.1 Troubleshooting instructions
Always start troubleshooting with the following checklist if faults occur after commissioning or
during operation. The routine takes you directly to the cause of the problem and the appropriate
remedial measures.
9.2 System error messages
Serious system errors are always recognized by the instrument as "Fault message", and are shown
as a lightning flash ($) on the display!
"
Caution!
In the event of a serious fault, a flowmeter might have to be returned to the manufacturer
for repair. Important procedures must be carried out before you return a flowmeter to
Endress+Hauser 101.
Always enclose a duly completed "Declaration of contamination" form. You will find a preprinted
blank of this form at the back of this manual.
!
Note!
See also the information on 40.
Check the display
No display visible and no
output signals present.
1. Check the supply voltage Terminals 1, 2
2. Check device fuse 100
85 to 260 V AC: 0.8 A slow-blow / 250 V
20 to 55 V AC and 16 to 62 V DC: 2 A slow-blow / 250 V
3. Measuring electronics defective order spare parts 95
No display visible, but
output signals are present.
1. Check whether the ribbon-cable connector of the display module is correctly plugged
into the amplifier board 95
2. Display module defective order spare parts 95
3. Measuring electronics defective order spare parts 95
Display texts are in a
foreign language.
Switch off power supply. Press and hold down both the P keys and switch on the
measuring device. The display text will appear in English (default) and is displayed at
maximum contrast.
Measured value indicated,
but no signal at the current
or pulse output
Measuring electronics defective order spare parts 95
No. # 8xx Other error messages with software options (Coriolis flowmeter)
800 S: M. FL. DEV. LIMIT
!: # 800
Advanced Diagnostics: The mass flow is outside the
limit value, set in the corresponding diagnosis function.
(G)
= Gas density in [kg/m
3
(lb/ft
3
)] for process conditions
Here, g
max(G)
can never be greater than g
max(F)
Measuring ranges for gases (Promass F, O):
Measuring ranges for gases (Promass E)
Measuring ranges for gases (Promass P, S, H (Ta))
DN x
[mm] [inch]
8 3/8 60
15 80
25 1 90
40 1 90
50 2 90
80 3 110
100 4 130
150 6 200
250 10 200
DN x
[mm] [inch]
8 3/8 85
15 110
25 1 125
40 1 125
50 2 125
80 3 155
DN x
[mm] [inch]
8 3/8 60
15 80
25 1 90
40
1)
1
1)
90
50
1)
2
1)
90
1)
only Promass P, S
Proline Promass 83 Technical data
Endress+Hauser 105
Measuring ranges for gases (Promass A)
Measuring ranges for gases (Promass I)
Measuring ranges for gases (Promass X)
Calculation example for gas:
Sensor type: Promass F, DN 50
Gas: air with a density of 60.3 kg/m (at 20 C and 50 bar)
Measuring range (liquid): 70 000 kg/h
x = 90 (for Promass F DN 50)
Max. possible full scale value:
g
max(G)
= g
max(F)
(G)
x [kg/m] = 70 000 kg/h 60.3 kg/m 90 kg/m = 46 900 kg/h
Recommended full scale values
See Page 127 ff. ("Limiting flow")
Operable flow range Greater than 1000 : 1. Flows above the preset full scale value do not overload the amplifier, i.e.
totalizer values are registered correctly.
DN x
[mm] [inch]
1 1/24 32
2 1/12 32
4 1/8 32
DN x
[mm] [inch]
8 3/8 60
15 80
15 FB FB 90
25 1 90
25 FB 1 FB 90
40 1 90
40 FB 1 FB 90
50 2 90
50 FB 2 FB 110
80 3 110
FB = Full bore versions of Promass I
DN x
[mm] [inch]
350 14 200
Technical data Proline Promass 83
106 Endress+Hauser
Input signal Status input (auxiliary input):
U = 3 to 30 V DC, R
i
= 5 kO, galvanically isolated.
Configurable for: totalizer reset, positive zero return, error message reset, start zero point
adjustment, batching start/stop (optional)
Current input:
Active/passive selectable, galvanically isolated, resolution: 2 A
Active: 4 to 20 mA, R
L
< 700 O, U
out
= 24 V DC, short-circuit proof
Passive: 0/4 to 20 mA, R
i
= 150 O, U
max
= 30 V DC
10.1.4 Output
Output signal Current output:
Active/passive selectable, galvanically isolated, time constant selectable (0.05 to 100 s), full scale
value selectable, temperature coefficient: typically 0.005% of full scale value/C, resolution: 0.5 A
Active: 0/4 to 20 mA, R
L
< 700 O (for HART: R
L
> 250 O)
Passive: 4 to 20 mA; supply voltage U
S
18 to 30 V DC; R
i
> 150 O
Pulse/frequency output:
Active/passive selectable, galvanically isolated
Active: 24 V DC, 25 mA (max. 250 mA during 20 ms), R
L
> 100 O
passive: open collector, 30 V DC, 250 mA
Frequency output: full scale frequency 2 to 10 000 Hz (f
max
= 12 500 Hz), on/off ratio 1:1, pulse
width max. 2 s
Pulse output: pulse value and pulse polarity selectable, pulse width configurable (0.05 to
2 000 ms)
Signal on alarm Current output:
Failsafe mode selectable (for example, according to NAMUR Recommendation NE 43)
Pulse/frequency output:
Failsafe mode selectable
Relay output:
De-energized in the event of fault or power supply failure
Load See "Output signal"
Switching output Relay output:
Normally closed (NC or break)
or normally open (NO or make) contacts available (default: relay 1 = NO, relay 2 = NC), max. 30
V / 0.5 A AC; 60 V / 0.1 A DC, galvanically isolated.
Configurable for: error messages, Empty Pipe Detection (EPD), flow direction, limit values, batching
valve 1 and 2 (optional).
Low flow cut off Switch points for low flow cut off are selectable.
Galvanic isolation All circuits for inputs, outputs, and power supply are galvanically isolated from each other.
Proline Promass 83 Technical data
Endress+Hauser 107
10.1.5 Power supply
Electrical connections Page 25 ff.
Supply voltage 85 to 260 V AC, 45 to 65 Hz
20 to 55 V AC, 45 to 65 Hz
16 to 62 V DC
Cable entries Power supply and signal cables (inputs/outputs):
Cable entry M20 1.5 (8 to 12 mm / 0.31 to 0.47 inch)
Threads for cable entries, 1/2" NPT, G 1/2"
Connecting cable for remote version:
Cable entry M20 1.5 (8 to 12 mm / 0.31 to 0.47 inch)
Threads for cable entries, 1/2" NPT, G 1/2"
Cable specifications
remote version
27
Power consumption AC: <15 VA (including sensor)
DC: <15 W (including sensor)
Switch-on current:
max. 13.5 A (< 50 ms) at 24 V DC
max. 3 A (< 5 ms) at 260 V AC
Power supply failure Lasting min. 1 power cycle:
EEPROM and T-DAT save measuring system data if power supply fails.
HistoROM/S-DAT: exchangeable data storage chip which stores the data of the sensor
(nominal diameter, serial number, calibration factor, zero point, etc.)
Potential equalization No measures necessary.
Technical data Proline Promass 83
108 Endress+Hauser
10.1.6 Performance characteristics
Reference operating
conditions
Error limits following ISO/DIN 11631
Water, typically +15 to +45 C (+59 to +113 F); 2 to 6 bar (29 to 87 psi)
Data according to calibration protocol 5 C (9 F) and 2 bar (29 psi)
Accuracy based on accredited calibration rigs according to ISO 17025
Performance characteristic
Promass A
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 109.
Mass flow and volume flow (liquids): 0.10% o.r.
Mass flow (gases): 0.50% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.02 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.002 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0003401
Fig. 50: Max. measured error in % o.r. (example: Promass A, DN 2)
DN Max. full scale value Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min] [kg/h] or [l/h] [lb/min]
1 1/24 20 0.73 0.0010 0.000036
2 1/12 100 3.70 0.0050 0.00018
4 1/8 450 16.5 0.0225 0.0008
0
0.5
0.1
[%]
0 50 100 kg/h
0.2
0.3
0.4
10 5 20 30 40 60 70 80 90
Proline Promass 83 Technical data
Endress+Hauser 109
Flow values (example)
Repeatability
Design fundamentals 109
Mass flow and volume flow (liquids): 0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
A difference in pressure between the calibration pressure and the process pressure does not have
any effect on the accuracy.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Turn down Flow Max. measured error
[kg/h] [lb/min.] [% o.r.]
250:1 0.4 0.0147 1.250
100:1 1.0 0.0368 0.500
25:1 4.0 0.1470 0.125
10:1 10 0.3675 0.100
2:1 50 1.8375 0.100
Design fundamentals 109
Base accuracy for
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.50
Technical data Proline Promass 83
110 Endress+Hauser
Performance characteristic
Promass E
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 112.
Mass flow and volume flow (liquids): 0.25% o.r.
Mass flow (gases): 0.75% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.02 g/cm
(valid over the entire temperature range and density range 129)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0004611
Fig. 51: Max. measured error in % o.r. (example: Promass E, DN 25)
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.20 0.0074
15 0.65 0.0239
25 1 1.80 0.0662
40 1 4.50 0.1654
50 2 7.00 0.2573
80 3 18.00 0.6615
0
0.5
0.2
1.0
[%]
0 1 2 4 6 8 10 12 14 16 18 t/h
Proline Promass 83 Technical data
Endress+Hauser 111
Flow values (example)
Repeatability
Design fundamentals 112
Mass flow and volume flow (liquids): 0.10% o.r.
Mass flow (gases): 0.35% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
250 : 1 72 2.646 2.50
100 : 1 180 6.615 1.00
25 : 1 720 26.46 0.25
10 : 1 1800 66.15 0.25
2 : 1 9000 330.75 0.25
Design fundamentals 112
DN
[mm] [inch] [% o.r./bar]
8 3/8 no influence
15 no influence
25 1 no influence
40 1 no influence
50 2 0.009
80 3 0.020
Technical data Proline Promass 83
112 Endress+Hauser
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Performance characteristic
Promass F
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 114.
Mass flow and volume flow (liquids):
0.05% o.r. (PremiumCal, for mass flow)
0.10% o.r.
Mass flow (gases): 0.35% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.01 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.001 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability Promass F (standard)
Base accuracy for
Mass flow liquids 0.25
Volume flow liquids 0.25
Mass flow gases 0.75
DN Zero point stability Promass F (Standard)
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.030 0.001
15 0.200 0.007
25 1 0.540 0.019
40 1 2.25 0.083
50 2 3.50 0.129
80 3 9.00 0.330
100 4 14.00 0.514
150 6 32.00 1.17
250 10 88.00 3.23
Proline Promass 83 Technical data
Endress+Hauser 113
Zero point stability Promass F (high-temperature version)
Example for max. measured error
a0004604
Fig. 52: Max. measured error in % o.r. (example: Promass F, DN 25)
Flow values (example)
Repeatability
Design fundamentals 114.
Mass flow and volume flow (liquids):
0.025% o.r. (PremiumCal, for mass flow)
0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
DN Zero point stability Promass F (high-temperature version)
[mm] [inch] [kg/h] or [l/h] [lb/min]
25 1 1.80 0.0661
50 2 7.00 0.2572
80 3 18.0 0.6610
0
0.5
0.2
1.0
[%]
0 2 4 6 8 10 12 14 16 18 t/h
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
500 : 1 36 1.323 1.5
100 : 1 180 6.615 0.3
25 : 1 720 26.46 0.1
10 : 1 1800 66.15 0.1
2 : 1 9000 330.75 0.1
Design fundamentals 114
Technical data Proline Promass 83
114 Endress+Hauser
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
DN Promass F (standard) Promass F (high-temperature version)
[mm] [inch] [% o.r./bar] [% o.r./bar]
8 3/8 no influence
15 no influence
25 1 no influence no influence
40 1 0.003
50 2 0.008 0.008
80 3 0.009 0.009
100 4 0.007
150 6 0.009
250 10 0.009
Base accuracy for
Mass flow liquids, PremiumCal 0.05
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.35
Proline Promass 83 Technical data
Endress+Hauser 115
Performance characteristic
Promass H
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 117.
Mass flow and volume flow (liquids)
Zirconium 702/R 60702 and Tantalum 2.5W: 0.10% o.r.
Mass flow (gases)
Tantalum 2.5W: 0.50% o.r.
Density (liquids)
Zirconium 702/R 60702 and Tantalum 2.5W
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.02 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.002 g/cm
(optional, valid range: +10 to +80 C (+50 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0004611
Fig. 53: Max. measured error in % o.r. (example: Promass H, DN 25)
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.20 0.007
15 0.65 0.024
25 1 1.80 0.066
40 1 4.50 0.165
50 2 7.00 0.257
0
0.5
0.2
1.0
[%]
0 1 2 4 6 8 10 12 14 16 18 t/h
Technical data Proline Promass 83
116 Endress+Hauser
Flow values (example)
Repeatability
Design fundamentals 117.
Material measuring tube: Zirconium 702/R 60702
Mass flow and volume flow (liquids): 0.05% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Material measuring tube: Tantalum 2.5W
Mass flow and volume flow (liquids): 0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.0005 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
250 : 1 72 2.646 2.50
100 : 1 180 6.615 1.00
25 : 1 720 26.46 0.25
10 : 1 1800 66.15 0.10
2 : 1 9000 330.75 0.10
Design fundamentals 117
DN Promass H Zirconium 702/R 60702 Promass H Tantalum 2.5W
[mm] [inch] [% o.r./bar] [% o.r./bar]
8 3/8 0.017 0.010
15 0.021 0.010
25 1 0.013 0.012
40 1 0.018
50 2 0.020
Proline Promass 83 Technical data
Endress+Hauser 117
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Performance characteristic
Promass I
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 119.
Mass flow and volume flow (liquids): 0.10% o.r.
Mass flow (gases): 0.50% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.02 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.004 g/cm
(optional, valid range: +10 to +80 C (+50 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Base accuracy for
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.50
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.150 0.0055
15 0.488 0.0179
15 FB FB 1.350 0.0496
25 1 1.350 0.0496
25 FB 1 FB 3.375 0.124
40 1 3.375 0.124
40 FB 1 FB 5.250 0.193
50 2 5.250 0.193
50 FB 2 FB 13.50 0.496
80 3 13.50 0.496
FB = Full bore
Technical data Proline Promass 83
118 Endress+Hauser
Example for max. measured error
a0004611
Fig. 54: Max. measured error in % o.r. (example: Promass I, DN 25)
Flow values (example)
Repeatability
Design fundamentals 119
Mass flow and volume flow (liquids): 0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
0
0.5
0.2
1.0
[%]
0 1 2 4 6 8 10 12 14 16 18 t/h
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
250 : 1 72 2.646 1.875
100 : 1 180 6.615 0.750
25 : 1 720 26.46 0.188
10 : 1 1800 66.15 0.100
2 : 1 9000 330.75 0.100
Design fundamentals 119
Proline Promass 83 Technical data
Endress+Hauser 119
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Performance characteristic
Promass O
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 121.
Mass flow and volume flow (liquids):
0.05% o.r. (PremiumCal, for mass flow)
0.10% o.r.
Mass flow (gases): 0.35% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.01 g/cm
(valid over the entire temperature range and density range 129)
DN
[mm] [inch] [% o.r./bar]
8 3/8 0.006
15 0.004
15 FB FB 0.006
25 1 0.006
25 FB 1 FB no influence
40 1 no influence
40 FB 1 FB 0.003
50 2 0.003
50 FB 2 FB 0.003
80 3 0.003
FB = Full bore
Base accuracy for
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.50
Technical data Proline Promass 83
120 Endress+Hauser
Special density calibration: 0.001 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0015774
Fig. 55: Max. measured error in % o.r. (example DN 80)
Flow values (example DN 80)
DN Zero point stability Promass F (Standard)
[mm] [inch] [kg/h] or [l/h] [lb/min]
80 3 9.00 0.330
100 4 14.00 0.514
150 6 32.00 1.17
0
0.5
0.2
1.0
[%]
0 20 40 60 80 100 120 140 160 180 t/h
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
500 : 1 360 13.23 1.5
100 : 1 1800 66.15 0.3
25 : 1 7200 264.6 0.1
10 : 1 18000 661.5 0.1
2 : 1 90000 3307.5 0.1
Design fundamentals 121
Proline Promass 83 Technical data
Endress+Hauser 121
Repeatability
Design fundamentals 121.
Mass flow and volume flow (liquids):
0.025% o.r. (PremiumCal, for mass flow)
0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
DN Promass F (standard)
[mm] [inch] [% o.r./bar]
80 3 0.0055
100 4 0.0035
150 6 0.002
Base accuracy for
Mass flow liquids, PremiumCal 0.05
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.35
Technical data Proline Promass 83
122 Endress+Hauser
Performance characteristic
Promass P
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 123.
Mass flow and volume flow (liquids): 0.10% o.r.
Mass flow (gases): 0.50% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.01 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.002 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0006891
Fig. 56: Max. measured error in % o.r. (example: Promass P, DN 25)
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.20 0.007
15 0.65 0.024
25 1 1.80 0.066
40 1 4.50 0.165
50 2 7.00 0.257
0
0.5
0.2
1.0
[%]
0 1 2 4 6 8 10 12 14 16 18 t/h
Proline Promass 83 Technical data
Endress+Hauser 123
Flow values (example)
Repeatability
Design fundamentals 123.
Mass flow and volume flow (liquids): 0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
250 : 1 72 2.646 2.50
100 : 1 180 6.615 1.00
25 : 1 720 26.46 0.25
10 : 1 1800 66.15 0.10
2 : 1 9000 330.75 0.10
Design fundamentals 123
DN
[mm] [inch] [% o.r./bar]
8 3/8 0.002
15 0.006
25 1 0.005
40 1 0.005
50 2 0.005
Base accuracy for
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.50
Technical data Proline Promass 83
124 Endress+Hauser
Performance characteristic
Promass S
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 125.
Mass flow and volume flow (liquids): 0.10% o.r.
Mass flow (gases): 0.50% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.01 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.002 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0004611
Fig. 57: Max. measured error in % o.r. (example: Promass S, DN 25)
DN Zero point stability
[mm] [inch] [kg/h] or [l/h] [lb/min]
8 3/8 0.20 0.007
15 0.65 0.024
25 1 1.80 0.066
40 1 4.50 0.165
50 2 7.00 0.257
0
0.5
0.2
1.0
[%]
0 1 2 4 6 8 10 12 14 16 18 t/h
Proline Promass 83 Technical data
Endress+Hauser 125
Flow values (example)
Repeatability
Design fundamentals 125.
Mass flow and volume flow (liquids): 0.05% o.r.
Mass flow (gases): 0.25% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
250 : 1 72 2.646 2.50
100 : 1 180 6.615 1.00
25 : 1 720 26.46 0.25
10 : 1 1800 66.15 0.10
2 : 1 9000 330.75 0.10
Design fundamentals 125
DN
[mm] [inch] [% o.r./bar]
8 3/8 0.002
15 0.006
25 1 0.005
40 1 0.005
50 2 0.005
Base accuracy for
Mass flow liquids 0.10
Volume flow liquids 0.10
Mass flow gases 0.50
Technical data Proline Promass 83
126 Endress+Hauser
Performance characteristic
Promass X
o.r. = of reading; 1 g/cm
3
= 1 kg/l; T = medium temperature
Maximum measured error
The following values refer to the pulse/frequency output.
The additional measured error at the current output is typically 5 A.
Design fundamentals 127.
Mass flow and volume flow (liquids):
0.05% o.r. (PremiumCal, for mass flow)
0.10% o.r.
Density (liquids)
Reference conditions: 0.0005 g/cm
Field density calibration: 0.0005 g/cm
(valid after field density calibration under process conditions)
Standard density calibration: 0.01 g/cm
(valid over the entire temperature range and density range 129)
Special density calibration: 0.001 g/cm
(optional, valid range: +5 to +80 C (+41 to +176 F) and 0.0 to 2.0 g/cm)
Temperature: 0.5 C 0.005 T C; 1 F 0.003 (T - 32) F
Zero point stability
Example for max. measured error
a0015646
Fig. 58: Max. measured error in % o.r. (example: Promass 83X, DN 350)
DN Zero point stability Promass F (Standard)
[mm] [inch] [kg/h] or [l/h] [lb/min]
350 14 175 6.42
0.2
[%]
0 kg/s 500 1000 1500 2000 2500 3000 4000
0.4
0.6
0.8
1.2
1.4
Proline Promass 83 Technical data
Endress+Hauser 127
Flow values (example)
Repeatability
Design fundamentals 127.
Mass flow and volume flow (liquids):
0.025% o.r. (PremiumCal, for mass flow)
0.05% o.r.
Density (liquids): 0.00025 g/cm
3
Temperature: 0.25 C 0.0025 T C; 0.5 F 0.0015 (T - 32) F
Influence of medium temperature
When there is a difference between the temperature for zero point adjustment and the process
temperature, the typical measured error of the sensor is 0.0002% of the full scale value / C
(0.0001% of the full scale value/F).
Influence of medium pressure
The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure and process pressure.
Design fundamentals
Dependent on the flow:
Flow > Zero point stability (Base accuracy 100)
Max. measured error: Base accuracy in % o.r.
Repeatability: Base accuracy in % o.r.
Flow < Zero point stability (Base accuracy 100)
Max. measured error: (Zero point stability measured value) 100% o.r.
Repeatability: (Zero point stability measured value) 100% o.r.
Turn down Flow Maximum measured error
[kg/h] [lb/min] [% o.r.]
500 : 1 8200 1.323 2.1
100 : 1 41 000 6.615 0.4
25 : 1 164 000 26.46 0.1
10 : 1 410 000 66.15 0.1
2 : 1 2 050 000 330.75 0.1
Design fundamentals 127
DN Promass F (standard)
[mm] [inch] [% o.r./bar]
350 14 0.009
Base accuracy for
Mass flow liquids, PremiumCal 0.05
Mass flow liquids 0.10
Volume flow liquids 0.10
Technical data Proline Promass 83
128 Endress+Hauser
10.1.7 Operating conditions: Installation
Installation instructions 14
Inlet and outlet runs There are no installation requirements regarding inlet and outlet runs.
Length of connecting cable
remote version
max. 20 m (65 ft)
System pressure 15
10.1.8 Operating conditions: Environment
Ambient temperature range Sensor and transmitter:
Standard: 20 to +60 C (-4 to +140F)
Optional: 40 to +60 C (-40 to +140F)
!
Note!
Install the device at a shady location. Avoid direct sunlight, particularly in warm climatic regions.
At ambient temperatures below 20 C (4 F) the readability of the display may be impaired.
Storage temperature 40 to +80 C (40 to +175 F), preferably +20 C (+68 F)
Degree of protection Standard: IP 67 (NEMA 4X) for transmitter and sensor
Shock resistance According to IEC 60068-2-31
Vibration resistance Acceleration up to 1 g, 10 to 150 Hz, following IEC 60068-2-6
CIP cleaning Yes
SIP cleaning Yes
Electromagnetic compatibility
(EMC)
To IEC/EN 61326 and NAMUR Recommendation NE 21
Proline Promass 83 Technical data
Endress+Hauser 129
10.1.9 Operating conditions: Process
Medium temperature range Sensor:
Promass F, A, P:
50 to +200 C (58 to +392 F)
Promass F (high-temperature version):
50 to +350 C (58 to +662 F)
Promass H:
Zirconium 702/R 60702: 50 to +200 C (58 to +392 F)
Tantalum 2.5W: 50 to +150 C (58 to +302 F)
Promass I, S:
50 to +150 C (58 to +302 F)
Promass E:
40 to +140 C (40 to +284 F)
Promass O
40 to +200 C (40 to +392 F)
Promass X
50 to +180 C (40 to +356 F)
Seals:
Promass F, E, H, I, S, P, O, X:
No internal seals
Promass A
No seals inlying.
Only for mounting sets with threaded connections:
Viton: 15 to +200 C ( 5 to +392 F)
EPDM: 40 to +160 C (40 to +320 F)
Silicon: 60 to +200 C (76 to +392 F)
Kalrez: 20 to +275 C (4 to +527 F);
Fluid density range 0 to 5000 kg/m
3
(0 to 312 lb/cf)
Technical data Proline Promass 83
130 Endress+Hauser
Limiting medium pressure
range (rated pressure)
The material load diagrams (pressure-temperature diagrams) for the process connections are
provided in the separate "Technical Information" document on the device in question. This can be
downloaded as a PDF file from www.endress.com. A list of the "Technical Information" documents
available is provided in the "Documentation" section 148.
Pressure ranges of secondary containment:
Promass A:
25 bar (362) psi
Promass E:
No secondary containment
Promass F:
DN 8 to 50 (3/8" to 2"): 40 bar (580 psi)
DN 80 (3"): 25 bar (362 psi)
DN 100 to 150 (4" to 6"): 16 bar (232 psi)
DN 250(10"): 10 bar (145 psi)
Promass H:
Zirconium 702/R 60702:
DN 8 to 15 (3/8" to "): 25 bar (362 psi)
DN 25 to 50 (1" to 2"): 16 bar (232 psi)
Tantalum 2.5W:
DN 8 to 25 (3/8" to 1"): 25 bar (362 psi)
DN 40 to 50 (1" to 2"): 16 bar (232 psi)
Promass I:
40 bar (580 psi)
Promass P:
DN 8 to 25 (3/8" to 1"): 25 bar (362 psi)
DN 40 (1"): 16 bar (232 psi)
DN 50 (2"): 10 bar (145 psi)
Promass S:
DN 8 to 40 (3/8" to 1"): 16 bar (232 psi)
DN 50 (2"): 10 bar (145 psi)
Promass O:
16 bar (232 psi)
Promass X:
Type approved, maximum allowable pressure according to ASME BPVC: 6 bar (87 psi)
Proline Promass 83 Technical data
Endress+Hauser 131
Limiting flow See the "Measuring range" section Page 101 ff.
Select nominal diameter by optimizing between required flow range and permissible pressure loss.
See the "Measuring range" section for a list of max. possible full scale values.
The minimum recommended full scale value is approx. 1/20 of the max. full scale value.
In most applications, 20 to 50% of the maximum full scale value can be considered ideal.
Select a lower full scale value for abrasive substances such as liquids with entrained solids
(flow velocity < 1 m/s (3 ft/s)).
For gas measurement the following rules apply:
Flow velocity in the measuring tubes should not be more than half the sonic velocity
(0.5 Mach).
The maximum mass flow depends on the density of the gas: formula 105
Pressure loss (SI units) Pressure loss depends on the properties of the fluid and on its flow. The following formulas can be
used to approximately calculate the pressure loss:
Pressure loss formulas for Promass F, E
Pressure loss formulas for Promass H, I, S, P
Reynolds number
a0004623
Re > 2300
1)
a0004626
Promass F DN 250
a0012135
Re < 2300
a0004628
Ap = pressure loss [mbar]
v = kinematic viscosity [m2/s]
g = mass flow [kg/s]
= fluid density [kg/m3]
d = inside diameter of measuring tubes [m]
K to K2 = constants (depending on nominal diameter)
a = 0.3
b = 91000
1)
To compute the pressure loss for gases, always use the formula for Re > 2300.
Reynolds number
a0003381
Re > 2300
1)
a0004631
Re < 2300
a0004633
Ap = pressure loss [mbar]
v = kinematic viscosity [m
2
/s]
g = mass flow [kg/s]
= fluid density [kg/m
3
]
d = inside diameter of measuring tubes [m]
K to K3 = constants (depending on nominal diameter)
1)
To compute the pressure loss for gases, always use the formula for Re > 2300.
Re =
2 g
p n r d
D r p = K
0.25 1.85 0.86
g n
Dp = K
a
1- a +
e
g
1.85 0.86
r
0.25
n
b ( 10 ) n
6
Dp = K1 + g n
K2
0.25 2
g n
r
Re =
p n r d
4 g
K3 g
2
r
+ D
0.25
g
1.75
-0.75
n r
Dp = K1 g n
K3 g
2
r
+
Technical data Proline Promass 83
132 Endress+Hauser
Pressure loss formulas for Promass A
Pressure loss formulas for Promass O, X
Reynolds number
a0003381
Re > 2300
1)
a0003380
Re < 2300
a0003379
Ap = pressure loss [mbar]
v = kinematic viscosity [m
2
/s]
g = mass flow [kg/s]
= density [kg/m
3
]
d = inside diameter of measuring tubes [m]
K to K1 = constants (depending on nominal diameter)
1)
To compute the pressure loss for gases, always use the formula for Re > 2300.
Reynolds number
A0015582
Pressure loss
A0015583
Ap = pressure loss [mbar]
v = kinematic viscosity [m
2
/s]
g = mass flow [kg/s]
= density [kg/m
3
]
d = inside diameter of measuring tubes [m]
A
0
to A
3
= constants (depending on nominal diameter)
n = number of tubes
Re =
p n r d
4 g
D n r p = K
0.25 1.75 0.75
g
D n p = K1 g
Re =
p n r d n
4 g
D p = (A + A Re )
0 1
A 1/A
2 3
2 g
5 n d p
2
r
1
( )
2
Proline Promass 83 Technical data
Endress+Hauser 133
Pressure loss coefficient for Promass F
a0001396
Fig. 59: Pressure loss diagram for water
DN d[m] K K1 K2
8 5.35 10
3
5.70 10
7
9.60 10
7
1.90 10
7
15 8.30 10
3
5.80 10
6
1.90 10
7
10.60 10
5
25 12.00 10
3
1.90 10
6
6.40 10
6
4.50 10
5
40 17.60 10
3
3.50 10
5
1.30 10
6
1.30 10
5
50 26.00 10
3
7.00 10
4
5.00 10
5
1.40 10
4
80 40.50 10
3
1.10 10
4
7.71 10
4
1.42 10
4
100 51.20 10
3
3.54 10
3
3.54 10
4
5.40 10
3
150 68.90 10
3
1.36 10
3
2.04 10
4
6.46 10
2
250 102.26 10
3
3.00 10
2
6.10 10
3
1.33 10
2
DN 50 DN 40
DN 25
DN 8
10000
1000
100
10
1
0.1
0.001 0.01 0.1 1
10 100 1000
DN 15
DN 80
DN 100
[mbar]
[t/h]
DN 150
DN 250
Technical data Proline Promass 83
134 Endress+Hauser
Pressure loss coefficient for Promass E
a0004606
Fig. 60: Pressure loss diagram for water
DN d[m] K K1 K2
8 5.35 10
3
5.70 10
7
7.91 10
7
2.10 10
7
15 8.30 10
3
7.62 10
6
1.73 10
7
2.13 10
6
25 12.00 10
3
1.89 10
6
4.66 10
6
6.11 10
5
40 17.60 10
3
4.42 10
5
1.35 10
6
1.38 10
5
50 26.00 10
3
8.54 10
4
4.02 10
5
2.31 10
4
80 40.50 10
3
1.44 10
4
5.00 10
4
2.30 10
4
DN 50
DN 40
DN 25
DN 8
10000
1000
100
10
1
0.1
0.001 0.01 0.1 1
10 100 1000
DN 15
[mbar]
[t/h]
DN 80
Proline Promass 83 Technical data
Endress+Hauser 135
Pressure loss coefficient for Promass A
a0003595
Fig. 61: Pressure loss diagram for water
1 Standard version
2 High pressure version
DN d[m] K K1
1 1.1 10
3
1.2 10
11
1.3 10
11
2 1.8 10
3
1.6 10
10
2.4 10
10
4 3.5 10
3
9.4 10
8
2.3 10
9
High pressure version
2 1.4 10
3
5.4 10
10
6.6 10
10
4 3.0 10
3
2.0 10
9
4.3 10
9
[mbar]
[kg/h]
1
DN 2
10000
1000
100
10
1
0.1 1 10 100 1000
DN 4
DN 1
2
Technical data Proline Promass 83
136 Endress+Hauser
Pressure loss coefficient for Promass H
a0004607
Fig. 62: Pressure loss diagram for water
DN d[m] K K1 K3
8 8.51 10
3
8.04 10
6
3.28 10
7
1.15 10
6
15 12.00 10
3
1.81 10
6
9.99 10
6
1.87 10
5
25 17.60 10
3
3.67 10
5
2.76 10
6
4.99 10
4
40 25.50 10
3
8.75 10
4
8.67 10
5
1.22 10
4
50 40.5 10
3
1.35 10
4
1.72 10
5
1.20 10
3
Pressure loss data includes interface between measuring tube and piping
1000
100
10
1
0.1
0.01 0.1 1 10 100
[mbar]
[t/h]
DN 40 DN 50 DN 25 DN 15 DN 8
Proline Promass 83 Technical data
Endress+Hauser 137
Pressure loss coefficient for Promass I
a0004608
Fig. 63: Pressure loss diagram for water
1 Standard versions
2 Full bore versions (*)
DN d[m] K K1 K3
8 8.55 10
3
8.1 10
6
3.9 10
7
129.95 10
4
15 11.38 10
3
2.3 10
6
1.3 10
7
23.33 10
4
15
1)
17.07 10
3
4.1 10
5
3.3 10
6
0.01 10
4
25 17.07 10
3
4.1 10
5
3.3 10
6
5.89 10
4
25
1)
26.4 10
3
7.8 10
4
8.5 10
5
0.11 10
4
40 26.4 10
3
7.8 10
4
8.5 10
5
1.19 10
4
40
1)
35.62 10
3
1.3 10
4
2.0 10
5
0.08 10
4
50 35.62 10
3
1.3 10
4
2.0 10
5
0.25 10
4
50
1)
54.8 10
3
2.3 10
3
5.5 10
4
1.0 10
2
80 54.8 10
3
2.3 10
3
5.5 10
4
3.5 10
2
Pressure loss data includes interface between measuring tube and piping
1)
DN 15, 25, 40, 50 "FB" = Full bore versions of Promass I
1000
100
10
1
0.1
0.01 0.1 1 10 100
DN 40
DN 25 *
DN 50
DN 40 *
DN 25
DN 15 *
DN 15
[mbar]
[t/h]
1
DN 8
DN 80
DN 50 *
2
Technical data Proline Promass 83
138 Endress+Hauser
Pressure loss coefficient for Promass S, P
a0004607
Fig. 64: Pressure loss diagram for water
DN d[m] K K1 K3
8 8.31 10
3
8.78 10
6
3.53 10
7
1.30 10
6
15 12.00 10
3
1.81 10
6
9.99 10
6
1.87 10
5
25 17.60 10
3
3.67 10
5
2.76 10
6
4.99 10
4
40 26.00 10
3
8.00 10
4
7.96 10
5
1.09 10
4
50 40.50 10
3
1.41 10
4
1.85 10
5
1.20 10
3
Pressure loss data includes interface between measuring tube and piping
1000
100
10
1
0.1
0.01 0.1 1 10 100
[mbar]
[t/h]
DN 40 DN 50 DN 25 DN 15 DN 8
Proline Promass 83 Technical data
Endress+Hauser 139
Pressure loss coefficient for Promass O
A0015630
Fig. 65: Pressure loss diagram for water
Pressure loss coefficient for Promass X
A0015428
Fig. 66: Pressure loss diagram for water
DN
d[mm] A
0
A
1
A
2
A
3
[mm] [inch]
80 3 38.5 0.72 4.28 0.36 0.24
100 4 49.0 0.70 3.75 0.35 0.22
150 6 66.1 0.75 2.81 0.33 0.19
10000
1000
100
10
1
0.1
1
10 100 1000
DN80
[mbar]
[t/h]
DN100
DN150
DN
d[mm] A
0
A
1
A
2
A
3
[mm] [inch]
350 14 102.3 0.76 3.80 0.33 0.23
10 000
1000
100
10
1
0.1
3 10 100 1000
[mbar]
DN 350
0.01
10 000[t/h]
Technical data Proline Promass 83
140 Endress+Hauser
Pressure loss (US units) Pressure loss is dependent on fluid properties nominal diameter. Consult Endress+Hauser for
Applicator PC software to determine pressure loss in US units. All important instrument data is
contained in the Applicator software program in order to optimize the design of measuring system.
The software is used for following calculations:
Nominal diameter of the sensor with fluid characteristics such as viscosity, density, etc.
Pressure loss downstream of the measuring point.
Converting mass flow to volume flow, etc.
Simultaneous display of various meter size.
Determining measuring ranges.
The Applicator runs on any IBM compatible PC with windows.
Proline Promass 83 Technical data
Endress+Hauser 141
10.1.10 Mechanical construction
Design / dimensions The dimensions and lengths of the sensor and transmitter are provided in the separate "Technical
Information" document on the device in question. This can be downloaded as a PDF file from
www.endress.com. A list of the "Technical Information" documents available is provided in the
"Documentation" section 148.
Weight Compact version: see table below
Remote version
Sensor: see table below
Wall-mount housing: 5 kg (11 lb)
Weight (SI units) All values (weight) refer to devices with flanges according to EN/DIN PN 40.
Weight data in [lb].
Promass F / DN 8 15 25 40 50 80 100 150 250*
Compact version 11 12 14 19 30 55 96 154 400
Compact version, high-temperature 14.7 30.7 55.7
Remote version 9 10 12 17 28 53 94 152 398
Remote version, high-temperature 13.5 29.5 54.5
* With 10" according to ASME B16.5 Cl 300 flanges
Promass E / DN 8 15 25 40 50 80
Compact version 8 8 10 15 22 31
Remote version 6 6 8 13 20 29
Promass A / DN 1 2 4
Compact version 10 11 15
Remote version 8 9 13
Promass H / DN 8 15 25 40 50
Compact version 12 13 19 36 69
Remote version 10 11 17 34 67
Promass I / DN 8 15 15FB 25 25FB 40 40FB 50 50FB 80
Compact version 13 15 21 22 41 42 67 69 120 124
Remote version 11 13 19 20 38 40 65 67 118 122
"FB" = Full bore versions of Promass I
Promass S / DN 8 15 25 40 50
Compact version 13 15 21 43 80
Remote version 11 13 19 41 78
Technical data Proline Promass 83
142 Endress+Hauser
Weight (US units) All values (weight) refer to devices with EN/DIN PN 40 flanges.
Weight data in [lb].
Promass P / DN 8 15 25 40 50
Compact version 13 15 21 43 80
Remote version 11 13 19 41 78
Promass O / DN
1)
80 100 150
Compact version 75 141 246
Remote version 73 139 244
1)
with Cl 900 flanges according to ASME
Promass X / DN
1)
350
Compact version 555
Remote version 553
1)
with 12" according to ASME B16.5 Cl 150 flanges
Promass F / DN 3/8" 1/2" 1" 1 " 2" 3" 4" 6" 10"*
Compact version 24 26 31 42 66 121 212 340 882
Compact version, high-temperature 32 68 123
Remote version 20 22 26 37 62 117 207 335 878
Remote version, high-temperature 30 65 120
* With 10" according to ASME B16.5 Cl 300 flanges
Promass E / DN 3/8" 1/2" 1 1 " 2" 3"
Compact version 18 18 22 33 49 69
Remote version 13 13 18 29 44 64
Promass A / DN 1/24" 1/12" 1/8"
Compact version 22 24 33
Remote version 18 20 29
Promass H / DN 3/8" 1/2" 1 1 " 2"
Compact version 26 29 42 79 152
Remote version 22 24 37 75 148
Promass I / DN 3/8" 1/2" 1/2"FB 1 " 1 "FB 3/8" 3/8"FB 1 1FB 2"
Compact version 29 33 46 49 90 93 148 152 265 273
Remote version 24 29 42 44 86 88 143 148 260 269
"FB" = Full bore versions of Promass I
Proline Promass 83 Technical data
Endress+Hauser 143
Material Transmitter housing:
Compact version
Compact version: powder coated die-cast aluminum
Stainless steel housing: stainless steel 1.4404/CF3M
Window material: glass or polycarbonate
Remote version
Remote field housing: powder coated die-cast aluminum
Wall-mount housing: powder coated die-cast aluminum
Window material: glass
Sensor housing / containment:
Promass F:
Acid- and alkali-resistant outer surface
Stainless steel 1.4301/1.4307/304L
Promass E, A, H, I, S, P:
Acid- and alkali-resistant outer surface
Stainless steel 1.4301/304
Promass X, O:
Acid- and alkali-resistant outer surface
Stainless steel 1.4404/316L
Promass S / DN 3/8" 1/2" 1 1 " 2"
Compact version 29 33 46 95 176
Remote version 24 29 42 90 172
Promass P / DN 3/8" 1/2" 1 1 " 2"
Compact version 29 33 46 95 176
Remote version 24 29 42 90 172
Promass O / DN
1)
3" 4" 6"
Compact version 165 311 542
Remote version 161 306 538
1)
with Cl 900 flanges according to ASME
Promass X / DN
1)
350
Compact version 1224
Remote version 1219
1)
with 12" according to ASME B16.5 Cl 150 flanges
Technical data Proline Promass 83
144 Endress+Hauser
Connection housing, sensor (remote version):
Stainless steel 1.4301/304 (standard, not Promass X)
Powder coated die-cast aluminum
(high-temperature version and version for heating)
Process connections:
Promass F:
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
stainless steel 1.4404/316L
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
Alloy C-22 2.4602/N 06022
DIN 11864-2 Form A (flat flange with groove) stainless steel 1.4404/316L
Threaded hygienic connections DIN 11851/ DIN 11864-1, Form A / ISO 2853 / SMS 1145
stainless steel 1.4404/316L
Tri-Clamp (OD-tubes) stainless steel 1.4404/316L
VCO connection stainless steel 1.4404/316L
Promass F (high-temperature version):
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
stainless steel 1.4404/316L
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
Alloy C-22 2.4602 (N 06022)
Promass E:
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
stainless steel 1.4404/316L
DIN 11864-2 Form A (flat flange with groove) stainless steel 1.4404/316L
VCO connection stainless steel 1.4404/316L
Threaded hygienic connections DIN 11851/ DIN 11864-1, Form A / ISO 2853 / SMS 1145
stainless steel 1.4404/316L
Tri-Clamp (OD-tubes) stainless steel 1.4404/316L
Promass A:
Mounting set for flanges EN 1092-1 (DIN 2501) / ASME B16.5 / JIS B2220
stainless steel 1.4539/904L, Alloy C-22 2.4602/N 06022.
Loose flanges stainless steel 1.4404/316L
VCO coupling stainless steel 1.4539/904L, Alloy C-22 2.4602/N 06022
Tri-Clamp (OD-tubes) (1/2") stainless steel 1.4539/904L
Mounting set for SWAGELOK (1/4", 1/8") stainless steel 1.4401/316
Mounting set for NPT-F (1/4") stainless steel 1.4539/904L1.4539/904L,
Alloy C-22 2.4602/N 06022
Promass H:
Flanges EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
stainless steel 1.4301/304, parts in contact with medium: zirconium 702/R 60702 or
tantalum 2.5W
Promass I:
Flanges EN 1092-1 (DIN 2501) / according to ASME B16.5 / JIS B2220
stainless steel 1.4301/304
DIN 11864-2 Form A (flat flange with groove) titanium grade 2
Threaded hygienic connection DIN 11851 / SMS 1145 titanium grade 2
Threaded hygienic connection ISO 2853 / DIN 11864-1 titanium grade 2
Tri-Clamp (OD-tubes) titanium grade 2
Proline Promass 83 Technical data
Endress+Hauser 145
Promass S:
Flanges EN 1092-1 (DIN 2501) / JIS B2220 stainless steel 1.4404/316/316L
Flanges according to ASME B16.5 stainless steel 1.4404/316/316L
DIN 11864-2 Form A (flat flange with groove) stainless steel 1.4435/316L
Threaded hygienic connections DIN 11851/ DIN 11864-1, Form A / ISO 2853 / SMS 1145
stainless steel 1.4404/316L
Tri-Clamp (OD-Tubes) stainless steel 1.4435/316L
Clamp aseptic connection DIN 11864-3, Form A stainless steel 1.4435/316L
Clamp pipe connection DIN 32676/ISO 2852 stainless steel 1.4435/316L
Promass P:
Flanges EN 1092-1 (DIN 2501) / JIS B2220 stainless steel 1.4404/316/316L
Flanges according to ASME B16.5 stainless steel 1.4404/316/316L
DIN 11864-2 Form A (flat flange with groove), BioConnect
stainless steel 1.4435/316L
Promass O:
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5
stainless steel 25Cr duplex F53/EN 1.4410 (superduplex)
Promass X:
Flanges according to EN 1092-1 (DIN 2501) / according to ASME B16.5
stainless steel 1.4404/316/316L
Measuring tube(s):
Promass F:
DN 8 to 100 (3/8" to 4"): stainless steel 1.4539/904L; manifold: 1.4404/316L
DN 150 (6"): stainless steel 1.4404/316L/1.4432
DN 250 (10"): stainless steel 1.4404/316L/1.4432; manifold: CF3M
DN 8 to 150 (3/8" to 6"): Alloy C-22 2.4602/N 06022
Promass F (high-temperature version):
DN 25, 50, 80 (1", 2", 3"): Alloy C-22 2.4602/N 06022
Promass E, S:
Stainless steel 1.4539/904L
Promass A:
Stainless steel 1.4539/904L, Alloy C-22 2.4602/N 06022
Promass H:
Zirconium 702/R 60702
Tantalum 2.5W
Technical data Proline Promass 83
146 Endress+Hauser
Promass I:
Titanium grade 9
Titanium grade 2 (flange disks)
Promass P:
Stainless steel 1.4435/316L
Promass O:
Stainless steel 25Cr Duplex EN 1.4410/UNS S32750 (superduplex)
Promass X:
Stainless steel 1.4404/316/316L; manifold: 1.4404/316/316L
Seals:
Promass F, E, H, I, S, P, O, X:
Welded process connections without internal seals
Promass A:
Welded process connections without internal seals.
Only for mounting sets with threaded connections: Viton, EPDM, Silikon, Kalrez
Material load diagram The material load diagrams (pressure-temperature diagrams) for the process connections are
provided in the separate "Technical Information" document on the device in question. This can be
downloaded as a PDF file from www.endress.com. A list of the "Technical Information" documents
available is provided in the "Documentation" section 148.
Process connections Page 138 ff.
Proline Promass 83 Technical data
Endress+Hauser 147
10.1.11 Operability
Display elements Liquid crystal display: illuminated, four lines with 16 characters per line
Selectable display of different measured values and status variables
At ambient temperatures below 20 C (4 F) the readability of the display may be impaired.
Operating elements Local operation with three optical keys (S/O/F)
Application-specific Quick Setup menus for straightforward commissioning
Language groups Language groups available for operation in different countries:
Western Europe and America (WEA):
English, German, Spanish, Italian, French, Dutch and Portuguese
Eastern Europe and Scandinavia (EES):
English, Russian, Polish, Norwegian, Finnish, Swedish and Czech
South and East Asia (SEA):
English, Japanese, Indonesian
China (CN):
English, Chinese
!
Note!
You can change the language group via the operating program "FieldCare".
Remote operation Operation by means of HART protocol
10.1.12 Certificates and approvals
CE mark The measuring system is in conformity with the statutory requirements of the EC Directives.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
C-tick mark The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
Ex approval Information about currently available Ex versions (ATEX, FM, CSA, IECEx, NEPSI) can be supplied
by your Endress+Hauser Sales Center on request. All explosion protection data are given in a
separate documentation which is also available upon request.
Sanitary compatibility 3A authorization (all measuring systems, except Promass H, O and X)
EHEDG-tested (all measuring systems, except Promass E, H, O and X)
Pressure measuring device
approval
The measuring devices can be ordered with or without PED (Pressure Equipment Directive). If a
device with PED is required, this must be ordered explicitly. For devices with nominal diameters
less than or equal to DN 25 (1"), this is neither possible nor necessary.
With the identification PED/G1/III on the sensor nameplate, Endress+Hauser confirms
conformity with the "Basic safety requirements" of Appendix I of the Pressure Equipment
Directive 97/23/EC.
Devices with this identification (with PED) are suitable for the following types of fluid:
Fluids of Group 1 and 2 with a steam pressure of greater or less than 0.5 bar (7.3 psi)
Unstable gases
Devices without this identification (without PED) are designed and manufactured according to
good engineering practice. They correspond to the requirements of Art. 3, Section 3 of the
Pressure Equipment Directive 97/23/EC. Their application is illustrated in Diagrams 6 to 9 in
Appendix II of the Pressure Equipment Directive 97/23/EC.
Functional safety SIL -2: In accordance with IEC 61508/IEC 61511-1 (FDIS)
Technical data Proline Promass 83
148 Endress+Hauser
Other standards and
guidelines
EN 60529
Degrees of protection by housing (IP code).
EN 61010-1
Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures.
IEC/EN 61326
"Emission in accordance with requirements for Class A".
Electromagnetic compatibility (EMC-requirements).
NAMUR NE 21
Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment.
NAMUR NE 43
Standardization of the signal level for the breakdown information of digital transmitters with
analog output signal.
NAMUR NE 53
Software of field devices and signal-processing devices with digital electronics.
10.1.13 Ordering information
The Endress+Hauser service organization can provide detailed ordering information and
information on the order codes on request.
10.1.14 Accessories
Various accessories, which can be ordered separately from Endress+Hauser, are available for the
transmitter and the sensor 83.
10.1.15 Supplementary Documentation
Flow measuring technology (FA00005D)
Description of Device Functions Promass 83 (BA00060D)
Supplementary documentation on Ex-ratings: ATEX, FM, CSA, IECEx NEPSI
Special Documentation
Functional safety manual Promass 80, 83 (SD00077D)
Technical Information
Promass 80A, 83A (TI00054D)
Promass 80E, 83E (TI00061D)
Promass 80F, 83F (TI00101D)
Promass 80H, 83H (TI00074D)
Promass 80I, 83I (TI00075D)
Promass 80P, 83P (TI00078D)
Promass 80S, 83S (TI00076D)
Promass 83O (TI00112D)
Promass 83X (TI00110D)
Proline Promass 83 Index
Endress+Hauser 149
Index
A
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Ambient temperature range. . . . . . . . . . . . . . . . . . . . . . . 128
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Applicator (selection and configuration software) . . . . . . . . 84
Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
B
Batching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
C
Cable entries
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cable entry
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Cable specifications (remote version) . . . . . . . . . . . . . . . . . 27
CE mark (declaration of conformity) . . . . . . . . . . . . . . . . . 11
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CIP cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Cleaning
CIP cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82, 128
Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
SIP cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Code entry (function matrix) . . . . . . . . . . . . . . . . . . . . . . . 39
Commissioning
Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Two current outputs . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Zero point adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 77
Commubox FXA195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Commubox FXA195 (electrical connection). . . . . . . . . . . . 30
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connection
See Electrical connection
C-tick mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Current input
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Current output
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Current outputs, two
Configuration active/passive . . . . . . . . . . . . . . . . . . . . 67
D
Data back-up (of device data with T-DAT) . . . . . . . . . . . . . 66
Declaration of conformity (CE mark) . . . . . . . . . . . . . . . . . 11
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . 31, 128
Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device description files . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Device designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Device functions
See Description of Device Functions manual
Display
Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Turning the display . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
E
Electrical connection
Cable specifications (remote version) . . . . . . . . . . . . . . 27
Commubox FXA195 . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Degree of protection. . . . . . . . . . . . . . . . . . . . . . . . . . . 31
HART handheld terminal . . . . . . . . . . . . . . . . . . . . . . . 30
Error messages
Confirming error messages . . . . . . . . . . . . . . . . . . . . . . 40
Process error (application error) . . . . . . . . . . . . . . . . . . 91
System error (device error) . . . . . . . . . . . . . . . . . . . . . . 86
Error types (system and process errors). . . . . . . . . . . . . . . . 40
European Pressure Equipment Directive. . . . . . . . . . . . . . 147
Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
F
F-Chip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Field Xpert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Field Xpert SFX100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FieldCare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
FieldCheck (tester and simulator). . . . . . . . . . . . . . . . . . . . 84
Flow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1617
Frequency output
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
function description
See Description of Device Functions manual
Function groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Fuse, replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
FXA193. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
FXA195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
G
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Gas Measurement
Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
H
HART
Command classes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Command No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Handheld terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Hazardous substances . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
HOME position (display operating mode) . . . . . . . . . . . . . . 33
I
Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inlet and outlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Inlet runs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
See Installation conditions
Proline Promass 83 Index
150 Endress+Hauser
Installation conditions
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Inlet and outlet runs. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Orientation (vertical, horizontal) . . . . . . . . . . . . . . . . . 16
System pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Vertical pipe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Special instructions for Promass F, E, H, P and S. . . . . . 18
Special instructions for Promass I and P
with Eccentric Tri-clamps . . . . . . . . . . . . . . . . . . . . . . 18
Special instructions for Promass I and P
with hygienic connections . . . . . . . . . . . . . . . . . . . . . . 19
Installing the wall-mount housing . . . . . . . . . . . . . . . . . . . 23
Insulation of sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
L
Language groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Length of connecting cable . . . . . . . . . . . . . . . . . . . . . . . 128
Life Cycle Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Limiting flow
See Measuring range
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Local display
See Display
Low flow cutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
M
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Material load diagram . . . . . . . . . . . . . . . . . . . . . . . 130, 146
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Measuring principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . 103105
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Medium pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Medium temperature range . . . . . . . . . . . . . . . . . . . . . . . 129
N
Nameplate
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Nominal pressure
See Medium pressure range
O
Operable flow range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Operation
Device description files. . . . . . . . . . . . . . . . . . . . . . . . . 43
FieldCare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
HART handheld terminal . . . . . . . . . . . . . . . . . . . . . . . 42
Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Order code
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Outlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
P
Performance characteristic
Promass A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Promass E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Promass F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112, 126
Promass H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Promass I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Promass O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Promass P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Promass S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Post-installation check (checklist) . . . . . . . . . . . . . . . . . . . 25
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Power supply (supply voltage) . . . . . . . . . . . . . . . . . . . . . 107
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Pressure loss (formulas, pressure loss diagrams) . . . . . . . . 131
Pressure measuring device approval . . . . . . . . . . . . . . . . 147
Pressure monitoring connections. . . . . . . . . . . . . . . . . . . . 81
Printed circuit boards (installation/removal)
Field housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Wall-mount housing . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Process connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Process error
Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Process error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Programming mode
Disabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Pulsating flow
Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Pulse output
See Frequency output
Pumps, mounting location, system pressure. . . . . . . . . . . . 15
Purge connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Q
Quick Setup
Batching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Data back-up (of device data with T-DAT) . . . . . . . . . . 66
Gas Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Pulsating flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
R
Reference operating conditions . . . . . . . . . . . . . . . . . . . . 108
Registered trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Relay output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Replacement
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Returning devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
S
Safety icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sanitary compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
S-DAT (HistoROM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Proline Promass 83 Index
Endress+Hauser 151
Seals
Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Medium temperature range . . . . . . . . . . . . . . . . . . . . 129
Replacing, replacement seals . . . . . . . . . . . . . . . . . . . . 82
Secondary containment
Gas purging, pressure monitoring connections . . . . . . . 81
Pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Sensor heating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sensor mounting
See Sensor installation
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
SIL (functional safety) . . . . . . . . . . . . . . . . . . . . . . . . . 6, 147
SIP cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Software
Amplifier display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Versions (history) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Standards, guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Status input
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Supplementary Ex documentation . . . . . . . . . . . . . . . . . . . . 6
Supply voltage (power supply) . . . . . . . . . . . . . . . . . . . . . 107
Switching output
See Relay output
System error
Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
System error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
T
T-DAT (HistoROM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Save/load (data back-up, e.g. for replacing devices) . . . 66
Technical data at a glance . . . . . . . . . . . . . . . . . . . . . . . . 103
Temperature ranges
Ambient temperature range . . . . . . . . . . . . . . . . . . . . 128
Medium temperature range . . . . . . . . . . . . . . . . . . . . 129
Storage temperature. . . . . . . . . . . . . . . . . . . . . . . . . . 128
Thermal insulation, general notes . . . . . . . . . . . . . . . . . . . 21
Transmitter
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installing the wall-mount housing . . . . . . . . . . . . . . . . 23
Turning the field housing (aluminum) . . . . . . . . . . . . . 22
Turning the field housing (stainless steel) . . . . . . . . . . . 22
Transporting the sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting and remedy . . . . . . . . . . . . . . . . . . . . . . . 86
V
Vertical pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 128
W
W@M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Wall-mount housing, installing . . . . . . . . . . . . . . . . . . . . . 23
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Wiring
See Electrical connection
Z
Zero point adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Proline Promass 83 Index
152 Endress+Hauser
P
/
S
F
/
K
o
n
t
a
X
I
V
Because of legal regulations and for the safety of our employees and operating equipment, we need the "Declaration of Hazardous Material
and De-Contamination", with your signature, before your order can be handled. Please make absolutely sure to attach it to the outside of the
packaging.
Aufgrund der gesetzlichen Vorschriften und zum Schutz unserer Mitarbeiter und Betriebseinrichtungen, bentigen wir die unterschriebene
"Erklrung zur Kontamination und Reinigung", bevor Ihr Auftrag bearbeitet werden kann. Bringen Sie diese unbedingt auen an der
Verpackung an.
Serial number
Seriennummer ________________________
Type of instrument / sensor
Gerte-/Sensortyp ____________________________________________
Process data/Prozessdaten Temperature _____ [F] [C]
Conductivity / ________
_____
Leitfhigkeit
/
[S/cm]
Temperatur Pressure _____ [psi] [ Pa ]
Viscosity _____ [cp] [mm /s]
_____
_____
/
/
Druck
Viskositt
2
corrosive
tzend
harmless
unbedenklich
other *
sonstiges*
toxic
giftig
Process
medium
Identification
CAS No.
flammable
entzndlich
harmful/
irritant
gesundheits-
schdlich/
reizend
Medium /concentration
Medium /Konzentration
Returned part
cleaned with
Medium for
process cleaning
Medium and warnings
Warnhinweise zum Medium
* explosive; oxidizing; dangerous for the environment; biological risk; radioactive
* explosiv; brandfrdernd; umweltgefhrlich; biogefhrlich; radioaktiv
Please tick should one of the above be applicable, include safety data sheet and, if necessary, special handling instructions.
Zutreffendes ankreuzen; trifft einer der Warnhinweise zu, Sicherheitsdatenblatt und ggf. spezielle Handhabungsvorschriften beilegen.
Description of failure / Fehlerbeschreibung __________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
We hereby certify that this declaration is filled out truthfully and completely to the best of our knowledge.We further certify that the returned
parts have been carefully cleaned. To the best of our knowledge they are free of any residues in dangerous quantities.
Wir besttigen
w
besttigen, die vorliegende Erklrung nach unserem besten Wissen wahrheitsgetreu und vollstndig ausgefllt zu haben. Wir
eiter, dass die zurckgesandten Teile sorgfltig gereinigt wurden und nach unserem besten Wissen frei von Rckstnden in gefahrbringen-
der Menge sind.
(place, date / Ort, Datum)
Company data /Angaben zum Absender
Company / ________________________________
_________________________________________________
Address /
_________________________________________________
_________________________________________________
Firma ___
Adresse
Phone number of contact person /
____________________________________________
Fax / E-Mail ____________________________________________
Your order No. / ____________________________
Telefon-Nr. Ansprechpartner:
Ihre Auftragsnr.
Medium zur
Endreinigung
Medium zur
Prozessreinigung
Medium im
Prozess
Used as SIL device in a Safety Instrumented System / Einsatz als SIL Gert in Schutzeinrichtungen
RA No.
Erklrung zur Kontamination und Reinigung
Declaration of Hazardous Material and De-Contamination
Please reference the Return Authorization Number (RA#), obtained from Endress+Hauser, on all paperwork and mark the RA#
clearly on the outside of the box. If this procedure is not followed, it may result in the refusal of the package at our facility.
Bitte geben Sie die von E+H mitgeteilte Rcklieferungsnummer (RA#) auf allen Lieferpapieren an und vermerken Sie diese
auch auen auf der Verpackung. Nichtbeachtung dieser Anweisung fhrt zur Ablehnung ihrer Lieferung.
Name, dept./Abt. (please print / ) bitte Druckschrift Signature / Unterschrift
www.endress.com/worldwide
BA00059D/06/EN/14.12
71197481
FM+SGML 10.0 ProMoDo