Professional Documents
Culture Documents
CZ 100 PDF
CZ 100 PDF
CZ 110
CZ 110 - INSTRUCTION MANUAL
15
Before handling the pistol read this manual carefully and observe
the following safety instructions.
Improper and careless handling of the pistol could result in unintentional
discharge and could cause injury, death or damage to property. The same
consequences can be caused by unauthorized modifications or
adjustments, corrosion, or use of non-standard or damaged ammunition.
In these cases the manufacturer shall not be responsible in any manner
whatsoever for the resultant consequences.
Before leaving the factory this pistol was tested, carefully inspected, and
packed. CZ cannot accept responsibility for product handling while in transit, or
upon leaving the factory. Therefore, please examine this pistol carefully at
the time of purchase to ensure that it is unloaded and undamaged.
This instruction manual should always accompany this pistol and that
even in the case of the loan or sale of this pistol.
CONTENTS
SAFETY INSTRUCTIONS 16
PISTOL DESCRIPTION AND TERMINOLOGY 17
CZ 110 Safety Elements 18
OPERATING INSTRUCTIONS 19
Ammunition 19
Removal of the Magazine 19
Magazine Loading 19
Pistol Loading 19
Reloading During Shooting 20
Unloading the Pistol 20
Firing Pin Release 20
Loaded Chamber Indicator Function 20
Sight Adjustment 20
Training without Live Cartridges 20
MAINTENANCE INSTRUCTIONS 21
Stripping for Cleaning - Disassembly 21
Firing Pin Disassembly 21
Magazine Disassembly 21
Cleaning the Pistol 22
Cleaning the Barrel Bore and the Cartridge Chamber 22
Cleaning of Other Pistol Parts 22
Preserving 22
TROUBLESHOOTING, CAUSES AND REMEDIES 23
ILLUSTRATION AND LIST OF PARTS 24
TECHNICAL SPECIFICATIONS 26
LIST OF ILLUSTRATIONS 26
CZ 110 - INSTRUCTION MANUAL
16
SAFETY INSTRUCTIONS
Always follow the safety instructions for your safety and the safety of others.
1. Always handle your pistol as if it were loaded.
2. Never point your pistol at anything you do not intend to shoot.
3. Never take anyone's word that a gun is unloaded.
4. Always make sure that your pistol is not loaded before laying it down, or
handing it to another person.
5. Always keep and carry your pistol empty, except when you intend to shoot.
6. Never abuse your pistol by using it for any purpose other than shooting.
7. Never leave your loaded pistol unattended.
8. Before loading your pistol be sure that barrel bore, chamber, and action are clean
and clear of obstructions. After shooting, clean a dirtied pistol as soon as possible.
9. Always use only clean, dry, original high quality commercially manufactured
ammunition, which is appropriate to the caliber of your pistol.
10. Never drink alcoholic beverages or take drugs before or during shooting.
11. If possible wear both safety glasses and ear protection when shooting.
12. Always keep clear and keep others clear of the ejection port.
13. Never squeeze the trigger or put your finger in the trigger guard until you are
aiming at a target and ready to shoot.
14. Always be absolutely sure of your target, and the area behind it, before you squeeze the
trigger. A bullet could travel through or past your target up to several hundred meters.
15. Never shoot at a hard surface such as rock, or a liquid surface such as water.
16. Never fire your pistol near an animal unless it is trained to accept the noise.
17. Never indulge in "horseplay" while holding your pistol.
18. Failure to fire: always hold the pistol, keeping it pointed towards the target, or
a safe open area and wait 30 seconds when the pistol fails to fire. If a hangfire
(slow ignition) has occurred, the round will fire within 30 seconds. If the round
does not fire, remove the magazine, eject the round and examine the primer; if
the firing pin indent on the primer is light, or off center, or non-existent, have
the pistol examined by a competent gunsmith.
19. Always make sure your pistol is not loaded before cleaning, storing or travelling.
20. Always keep and store your pistol and ammunition in separate locked
receptacles out of reach and sight of children and untrained people.
21. Never alter any parts of your pistol as the safety and proper function of your
pistol could be seriously compromised.
22. Always be aware that corrosion, use of damaged ammunition, dropping the
pistol on hard surfaces or other "coarse treatment" could cause a damage you
may not see. If something like this happens allow the pistol to be examined
and tested by a competent gunsmith.
CZ 110 - INSTRUCTION MANUAL
17
PISTOL DESCRIPTION AND TERMINOLOGY
The names of basic pistol parts used in this Instruction Manual are presented
in Fig. 1. Nomenclatures of all CZ 110 parts are presented in the section
Illustration and List of Parts.
The CZ 110 is a semi-automatic handgun incorporating short recoil. It is
designed for self-defense and aimed shooting up to 50 m distances. The CZ 110
utilizes the locked breech principle, with the barrel tilting upwards into engagement
with the ejection port. It is fitted with a trigger mechanism adapted to operate both
in SA/DA modes of fire, a firing pin safety, and a loaded chamber indicator. The
slide stays open when the last cartridge from the magazine has been fired. It has
a double-column magazine, with a single cartridge outlet. Characteristic features
of the CZ 110 are:
- simple handling
- ergonomical shape allowing shooting to be carried out by left or right hand
- comfortable grip and balance
- low trigger pull weight
- good results at instinctive shooting (without aiming)
- high accuracy of fire
- long service life
- high reliability, even with various types of bullets
- the slide stays open after the last cartridge has been fired
- illuminated sights for aiming under poor visibility conditions
- The wide trigger guard prevents snagging of the trigger by any objects, and
also any unintentional discharge during handling or dropping of the pistol.
- The slide can be cocked even with only one hand by positioning the rear sight or
slide protrusion against any fixed edged object and levering against that point.
Comments:
SA (Single Action)
The trigger mechanism operates in the single action mode - the trigger fulfils
only one function, i.e. firing pin release. The firing pin is released from its cocked
position, and the slide is either manually cocked (pull back at least 10 mm), or
cocked mechanically by a previous discharge. Trigger travel is short, and pull
weight is low. In the course of consecutive discharges, the firing pin automatically
re-cocks and remains in this position.
CZ 110 - INSTRUCTION MANUAL
18
DA (Double Action)
The trigger mechanism operates in the double action mode - the trigger fulfils
two functions, i.e. the firing pin is both cocked and released. Pulling the trigger
causes the firing pin to shift from its "at rest" position into the cocked position,
followed by its subsequent release. Trigger travel is longer and trigger pull weight
is higher than with the SA mode. Consecutive discharges automatically cock the
firing pin, which remains in this position. Follow-up discharges are in SA mode.
The DA mode is used for rapid first shots, in cases where the pistol is carried
with a cartridge in the chamber (see Section: Firing Pin Release). In the event of a
cartridge misfire, the DA mode is equally advantageous, enabling quick repetition
of the discharge procedures.
CZ 110 Safety Elements
The CZ 110 is designed in such a way, safe-guarding any unintended
discharge, even under the most demanding of conditions and the most stressful of
situations. This has been achieved chiefly by the combination of the following
safety elements:
- firing pin safety
- release of the firing pin from its cocked to its "at rest" position
- loaded chamber indicator
- trigger guard
- increased trigger pull weight and a longer trigger travel with the DA mode of fire
Firing Pin Safety
The firing pin safety keeps the firing pin blocked until the trigger is pulled back,
almost to its stop. This safety device minimizes the risk of accidental discharge
through mishandling, such as when a loaded pistol is dropped.
Firing Pin Release - from the cocked position to the "at rest" position.
Serves to shift the firing pin, from the cocked position to the "at rest" position
without the necessity of pulling the trigger. It is especially used in situations when
the pistol is loaded with a cartridge in the chamber. In this state, the pistol is safe
for all normal handling, and yet is ready for immediate use.
Loaded Chamber Indicator
The loaded chamber indicator is a device, which indicates the presence of a
cartridge in the cartridge chamber. The indicator is located on the left side of the slide.
The loaded chamber indicator status can be checked both by sight and by touch.
Trigger Guard
Prevents inadvertent pulling of the trigger while grabbing for, or dropping the
pistol; or should the pistol snag against its holster, an item of clothing, or any other
obstacle.
CZ 110 - INSTRUCTION MANUAL
19
OPERATING INSTRUCTIONS
WARNING:
Before shooting always wipe the barrel bore dry, and lubricate the slide guiding
rails with a suitable lubricating agent.
Ammunition
Use only factory-manufactured standard ammunition of appropriate caliber,
which are in compliance with CIP regulations (International Proof Commission for
Firearms) or SAAMI (Sporting Arms and Ammunition Manufacturers' Institute Inc.
of the United States). The use of other cartridges could damage the handgun or
cause malfunctions or injury to the shooter.
Removal of the Magazine
Hold the pistol in your right/left hand and depress the magazine catch with the
thumb/middle finger and by the other hand remove the magazine.
Magazine Loading
With the open end uppermost, grasp the magazine in one hand. Place
a cartridge on the magazine follower (Fig. 2). Press the cartridge down and back
until it touches the rear flat edge of the magazine. Place the next cartridge on top
of the previous cartridge and press down and back. We recommend that when
some cartridges are already loaded in the magazine, depress them slightly with
the thumb of the hand which holds the magazine.
The number of cartridges can be checked through the inspection holes in the
sides of the magazine. Do not try to exceed the magazine capacity - doing so can
cause a feeding failure.
Pistol Loading
CAUTION:
ALWAYS MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION WHEN LOADING!
Insert a loaded magazine and ensure that it has engaged the magazine catch.
Hold the pistol by the grip with one hand, and with the thumb and index finger
grasp the serrated finger grips on both sides of the slide. Retract the slide to the
stop and allow it to snap forward (Fig. 3). This procedure inserts a cartridge into
the chamber and the pistol is now ready to fire. In the case of any emergency the
pistol can be loaded even with only one hand, by the use of the barrel stop placed
against any fixed edged object.
If you do not intend to fire immediately, and you want the pistol to be ready for
instant use, release the firing pin in the manner described in the section Firing Pin
Release.
CZ 110 - INSTRUCTION MANUAL
20
Reloading During Shooting
When the last cartridge has been fired the slide will stay to the rear. Remove
the emptied magazine and replace it with a loaded one. Thumb down the slide
stop with the shooting hand (Fig. 4), or with the other hand draw back the slide
and allow it to snap forward (Fig. 3). The pistol is again loaded and ready to fire.
Unloading the Pistol
ALWAYS MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION!
- remove the magazine
- draw back the slide and verify that the cartridge chamber is empty
- let the slide snap fully forward
- depress the trigger (dry fire)
Firing Pin Release
MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION. Press the
firing pin release button up to its stop (markedly greater force will gradually be
needed) and release it (Fig. 5). Pressing the firing pin release button shifts the
firing pin from its cocked position onto the latch lug without the necessity of pulling
the trigger. After freeing the firing pin button, the firing pin shifts into its "at rest"
position. If there is a cartridge in the chamber, the pistol is safe for all normal
handling, yet ready for use in the double-action (DA) mode after the firing pin has
been released.
Loaded Chamber Indicator Function
The loaded chamber indicator protrudes from the side wall surface of the slide,
thereby indicating the presence of a cartridge in the cartridge chamber. The
loaded chamber indicator status can be checked both by sight and by touch.
Sight Adjustment
The pistol sights were sighted in at the manufacturing plant at a distance of 25 m so
that the mean point of impact approximately conforms to the point of aim.
Windage correction can be carried out by the drifting of the rear sight in the
dovetail. Elevation correction is carried out by exchanging the rear sights for
higher or lower sizes.
CAUTION:
In consideration of the fact that the firing pin block is located under the rear
sight, do not drift out the rear sight completely from its dovetail . Entrust
eventual rear sight exchange to a competent gunsmith.
Training without Live Cartridges
The enclosed plastic dummy cartridges are designed - as are their replaceable
inserts, for training shooting without cartridges ("dry shooting").
CZ 110 - INSTRUCTION MANUAL
21
MAINTENANCE INSTRUCTIONS
Stripping for Cleaning - Disassembly
ALWAYS MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION!
1. For the safety reasons remove the magazine first.
2. MAKE SURE THAT THERE IS NO CARTRIDGE IN THE CHAMBER!
3. Put your left thumb through the trigger guard and with the other fingers grasp
the top of the front part of the slide firmly (Fig. 6). Push the slide slightly back
until the position of the recess in the slide enables the removal of the
connecting pin from the pistol frame. Press down the connecting pin from the
right hand side of the firearm as deeply as possible (the magazine base corner
can be used to facilitate this operation) (Fig. 7). Pull out the connecting pin
from the left-hand side of the pistol frame. After removing the connecting pin, ease
the slide back to its initial position driven by the force of the recoil spring.
4. Grasp with one hand the pistol grip (as when shooting - see Fig. 8) and with
other hand retract the slide back approx. 5-10 mm to get the trigger
mechanism out of engagement. Pull the trigger and slip the slide barrel
assembly forward off the frame.
5. Ease the trigger pull.
6. Remove the recoil spring and guide and finally the barrel.
No further disassembly is needed for routine maintenance. When a great number
of cartridges has been fired, it is advisable to also clean the firing pin and magazine.
Firing Pin Disassembly
Using a suitable tool push in the rear end of the firing pin main spring guide
(below the level of firing pin retainer), and shift the firing pin retainer approx. 2 mm
down (Fig. 9). Then cover the firing pin retainer with your thumb (in order not to
lose the spring-loaded guide with its spring), and with the other hand pull the firing
pin retainer completely off the slide. Be very careful at this stage of the
disassembly procedure, as the spring with its guide are spring loaded and could fly
out, thus getting lost, or even causing injury. By means of a suitable tool depress
the firing pin block, and withdraw the firing pin with the firing pin insert, main
spring, and firing pin guide from the slide.
Magazine Disassembly
The magazine base is removed by pushing on the base lock, which sticks out
through a hole in the base. Slide the base about 5 mm towards the front of the
magazine. Cover the base with a thumb to prevent the loss of the magazine
spring. At the same time, disengage the base from its guiding projections with the
other hand. Be careful at the disassembly as the spring could fly out even cause
an injury.
WARNING:
No further disassembly of your pistol is recommended. Should your pistol
require adjustment or repair, be sure the task is entrusted to a competent gunsmith!
CZ 110 - INSTRUCTION MANUAL
22
Cleaning the Pistol
Clean the pistol
- each time you use it
- if you get your pistol wet
- as soon as possible after shooting
- at least once a year in a temperate climate
- as often as once a month in a tropical climate, or other demanding
environment
Cleaning the Barrel Bore and the Cartridge Chamber
If the pistol has not been fired or if only a few cartridges have been fired, clean the
barrel bore and cartridge chamber by the clean patch attached to the cleaning rod.
When the barrel bore is very dirty, apply a gun cleaning solution using
a cleaning brush. Let the solvent act for about 10 minutes (this time may vary
depending on the solvent agent being used). Then thoroughly scrub out the barrel
bore. Subsequently, dry the barrel bore and cartridge chamber with a clean patch
and check that all powder residues or fouling have been removed. If necessary
repeat this procedure.
The cleaning rod and the brush must be inserted into the barrel bore from the
chamber, to prevent wear or damage to the muzzle. Pass the brush all the way
through the barrel bore before reversing the movement. If you try to change
directions with the brush in the barrel, the brush could stick.
Cleaning of Other Pistol Parts
Other parts of the pistol (including the external surfaces of the barrel) should
be cleaned with a dry cloth, old toothbrush, brass bristle brush or a wooden
scraper. Preserving oil or paraffin oil can be used for proper cleaning. Never use
the agent designed for barrel bore cleaning! These solutions could remain in the
joints, and after some time could cause corrosion.
Check that cloth particles or brush bristles have not become lodged in any part
of the pistol.
Preserving
When the barrel bore, cartridge chamber, and all accessible metal parts are
clean and dry, wipe these parts with a cloth soaked in gun oil or apply the oil in a spray.
Remove all excess oil. The plastic parts do not need any preserver application.
Before shooting always wipe the barrel bore dry. At very low temperatures
remove the oil from all accessible parts or apply a lubricant prepared especially for
these conditions.
Use thick preserving agents for example, preserving grease only for a long-term
storage in demanding climate environments, and before any use of the pistol it
must be thoroughly removed from all parts of the firearm.
CZ 110 - INSTRUCTION MANUAL
23
TROUBLESHOOTING, CAUSES AND REMEDIES
If your pistol is properly used and maintained, malfunctions will rarely occur.
However, if such a situation does occur, please observe the following instructions.
CAUTION - If a malfunction occurs, the possibility of unintentional discharge is
substantially increased. For this reason, carefully observe the Safety Instructions
already mentioned above. Keep the pistol pointed in a safe direction, do not turn
the pistol against your body or anyone elses! Do not place your hands in front of
the barrel!
If you use your pistol for self-defense, or in law enforcement, please acquire
so-called "dummy cartridges" and practice fast clearing of malfunctions as
described below.
Malfunction Possible Cause Remedy
A round has not been
fed into the chamber or
the slide has not fully
locked with the barrel.
Magazine is not fully
inserted or is damaged.
The pistol or cartridges are
fouled (dirty) or too heavily
greased.
Insert magazine properly or
change magazine.
Clean the pistol and
cartridges and wipe them dry
or as case may be slightly
lubricate.
Misfire Defective cartridge
Firing pin hole fouled (dirty)
or unproper lubrication
agent used under low
temperature conditions.
Pull the trigger again. If
a discharge is not initiated,
follow the Safety Instructions
according to point 18.
Disassemble and clean the
firing pin or use a low
temperature lubricant.
A shot sounds "weak"
combined with failure to
eject the cartridge
case.
The primer has been
activated but no powder
load was inside the
cartridge case.
Unload the pistol and check
that the bullet is not lodged in
the barrel. A subsequent shot
could cause damage to the
barrel.
The spent case has not
been ejected.
Cartridge chamber,
extractor or ammunition
dirty, or unsuitable lubricant
in low temperature
environment.
Clean and wipe the pistol dry
or lubricate lightly with a
suitable agent. Use new and
clean ammunition.
If you cannot clear away any malfunction in the manner described above,
entrust the pistol to a competent gunsmith for inspection and repair.
CZ 110 - INSTRUCTION MANUAL
24
ILLUSTRATION AND LIST OF PARTS
CZ 110 - INSTRUCTION MANUAL
25
1 Slide
2 Barrel Stop
3 Firing Pin Stop
4 Detent Spring
5 Barrel Stop Detent
6 Extractor
7 Extractor Pin
8 Extractor Spring
9 Firing Pin Block
10 Firing Pin Block Spring
11 Firing Pin Block Detent
12 -
13 -
14 Rear Sight
15 Firing Pin
16 Firing Pin Spring
17 Main Spring
18 Main Spring Guide
19 Firing Pin Insert
20 Firing Pin Retainer
21 Barrel
22 Recoil Spring
23 Recoil Spring Guide Rod
24 Frame
25 Slide Stop
26 Slide Stop Spring
27 Insert
28 Insert Clip
29 Trigger
30 Trigger Spring
31 Trigger Pin
32 Trigger Bar
33 Trigger Bar Pin
34 Magazine Catch Spring
35 Cam
36 Cam Spring
37 Ejector Pin Spring
38 Ejector
39 Interrupter
40 Ejector Pin
41 Trigger Bar Spring
42 Trigger Bar Disconnector
43 Trigger Mechanism Housing
44 Magazine Catch
45 Connecting Pin
46 Magazine Body
47 Magazine Base
48 Magazine Spring
49 Follower
50 Magazine Base Lock
51 Loaded Chamber Indicator Nut *
52 Loaded Chamber Indicator *
53 Loaded Chamber Indicator Spring *
54 Firing Pin Catch
55 Slide Stop Pin
56 Slide Stop Spring
57 Push-Button
58 Push-Button Pin
59 Latch
60 Latch Pin
61 Interrupter Spring
Comments:
* Available on request
The numbers marked with dash (-) are stated here for the purpose of conformity
with the lists of other model parts only.
CZ 110 - INSTRUCTION MANUAL
26
TECHNICAL SPECIFICATIONS
Caliber
9 mm Luger
9 x 21
Overall length [mm] 180
Height [mm] 130
Width [mm] 31
Weight with empty magazine [g] 665
Barrel length [mm] 98
Sight radius [mm] 148
Magazine capacity [cartridges] 13 *
Trigger pull SA [N]
DA [N]
16 ! 24,5
max. 50
* To some countries, the CZ 110 pistols are supplied with a reduced magazine
capacity in compliance with local laws.
LIST OF ILLUSTRATIONS
1. The names of basic parts
2. Magazine loading
3. Pistol loading
4. Slide release from its rear position by depressing the slide stop
5. Firing pin release
6. Holding of the pistol during connecting pin removal
7. Depression of connecting pin, using a magazine base
8. Slide removal procedure
9. Firing pin disassembly
The Company, reserves the right to make any changes it thinks necessary to improve its
models or to meet any requirements of manufacturing or commercial nature.