Hobart CMA66 Manual
Hobart CMA66 Manual
800-854-6417
FAX 714-895-2141
www.cmadishmachines.com
Table of Contents
CMA-66
1.
1.1
SPECIFICATIONS................................................................................................. 2
CMA-66.......................................................................................................................................... 2
2.
2.1. 2.2.
2.2.1. Electrical ................................................................................................................................ 5 2.2.2. Plumbing................................................................................................................................. 5 2.2.3. Installation Notes.................................................................................................................... 5 2.2.4. Scrap Tray Assembly and Overflow Chute Installation.......................................................... 7 2.2.5. Pump Impeller Note................................................................................................................ 8 2.2.6. Optional Hood Adapter (set of two) ....................................................................................... 9 2.2.7. Optional Freestanding Scrap Trap and Adaptor Kit ............................................................ 10 2.2.8. Optional Auto-Fill............................................................................................................ 11 2.2.9. Field Installed Accessories ................................................................................................... 14 2.2.9.1. Chemical Dispensers .................................................................................................... 14 2.2.9.2. Hood Fan Motor ........................................................................................................... 14 2.2.10. CMA-66 Heater .................................................................................................................... 14 2.3. Safety Tips for the CMA-66 ......................................................................................................... 15
3.
3.1.
OPERATION ........................................................................................................ 16
Initial Setup .................................................................................................................................. 16 3.1.1. Optional Auto Fill Timer ...................................................................................................... 16 3.1.2. Rinse Pressure Regulator ..................................................................................................... 16 3.1.3. Wash Tank Temperature....................................................................................................... 16 3.2. Beginning Operation..................................................................................................................... 17 3.2.1. Chemical Dispensing ............................................................................................................ 18 3.2.1.1. Low Temperature Applications .................................................................................... 18 3.3. Regular Service and Maintenance Checklist ................................................................................ 19 3.4. 3.5. Quick service guide ...................................................................................................................... 21 Trouble Shooting .......................................................................................................................... 22
4. 5.
www.cmadishmachines.com
1. Specifications
1.1 CMA-66
CMA-66 L.T. CMA-66 H.T.
WATER CONSUMPTION PER RACK PER HOUR CONVEYOR SPEED FEET PER MINUTE OPERATING CAPACITY RACKS PER HOUR (NSF rated) OPERATING TEMPERATURE WASH (MIN) FINAL RINSE (MIN) WATER REQUIREMENTS INLET TEMPERATURE (MIN) WATER INLET SIZE FINAL RINSE SIZE DRAIN SIZE FINAL RINSE PRESSURE HOLDING TANK CAPACITY PUMP CAPACITY (ALL PUMPS) MOTORS WASH PUMP (3) CONVEYOR DIMENSIONS DEPTH WIDTH HEIGHT STANDARD TABLE HEIGHT MAX CLEARANCE FOR DISHES STRANDARD RACKS ELECTRICAL RATING
VOLTS
.8 GAL. 192 GAL. 6.75 242 140 - 150 F 140 - 150 F 140 F 3/4 1/2 2 20 PSI
.94 GAL. 192 GAL. 5.7 205 150 - 160 F 180 - 195 F 180 F
1 1 3 3 10 kW 750#
61 65 38 42
SHIPPING WEIGHT
APPROXIMATE
Page 2
Getting Started
2. Getting Started
2.1. Introduction to CMA-66
The CMA-66 is designed to give maximum cleaning in 66 inches. It represents the cleaning power of machines twice its length. The curtains incorporated in the machine minimize transfer from tank to tank during the wash and sanitizing procedures. Energy costs for running the CMA-66 have been greatly reduced by the introduction of stage washing. This design allows the heavy food soil to be removed in the first station, which provides a relatively clean dish before it reaches the wash stage in the center tank. The supply water to the CMA-66L must be a minimum of 140F, while the CMA-66H requires two supply lines; one at a minimum water temperature of 180F (for RINSE), and the other at a minimum temperature of 140 F (for FILL). Either model requires the supply water to be provided at 24-PSI (Pounds per Square Inch) minimum with 6 GPM (Gallons Per Minute) flow rate and 200 GPH (Gallons Per Hour) recovery rate. The pipe supplying the water must be 3/4. The plumbing connection is located at the top back of the machine. The CMA-66 features a scrap tray that may be emptied on a periodic basis without interruption of the flow of work and the manner in which the tank is filled ensures that the dishes are always rinsed with fresh water instead of re-circulated water. The CMA-66L is designed to deliver 0.8 gallons of fresh rinse water and the CMA-66H is designed to deliver 0.94 gallons of fresh rinse water for each rack. This water flows from the rinse and power wash tank into the pre-wash tank and then overflows into the scrap tray carrying debris with it, thereby providing a much cleaner environment for the wash and rinse cycles. A single-phase CMA-66 is available for installations where the only power available is 208V230V/1-PH. There are also enhancements that can be chosen when desired such as an optional Auto-Fill function, optional Vent Hood Adaptors and other machine accessories such as stainless steel dishtables. Call (800) 854-6417 for more information. This manual is structured to provide a complete reference guide to the CMA-66. It is presented in a manner that all users will be able to comprehend and use as an effective tool in supporting the operation and maintenance of the dishmachine. The first section explains how the machine is packaged and what to look for when receiving the machine. Instructions are provided in the manual explaining how to unpack the machine and then install and set up the machine for use. Requirements are given for plumbing, wiring, and space considerations. These attributes of the machine are always taken into consideration by our welltrained sales representatives prior to the order being placed. In the manual, additional installation guidance is given to ensure the machine can run at optimum conditions. The Operation Section of the manual may be used for instruction and procedures when required. We make this portion of the manual easy to understand so that all levels of operators may be able to read and comprehend the operation of the machine. The function of the machine itself is mostly automatic and takes little training to put into full operation. The Operation Section also includes diagnostic considerations for the machine when problems occur. We are committed to providing the best machines and customer service in the food industry and your feedback is welcome.
Page 3
Getting Started
2.2.
When you receive your new CMA-66, complete the assembly by installing the scrap tray assembly with its overflow chute, the two wrapper shields and the curtain rods, which are shipped inside the machine. After the box has been removed from the machine, remove the left and right stainless steel wrapper shields and bolt them in place with the nuts and bolts provided. The wrapper shield with the extra curtain clamps mounts onto the dirty end of the machine. Next, mount the scrap tray assembly and overflow chute into position (see section 2.2.4 Scrap Tray Assembly and Overflow Chute Installation). All of the spray arms should be inserted and in place over the wash tank compartments. There are a total of seven curtains used in the CMA-66; two are long-narrow, four are long-wide and one is short. The two long-narrow curtains and the one short curtain have shorter rods than the other four (long-wide) curtains. The short rods hold the curtains at the entrance and exit of the machine. The sketch below lists curtain positions 1 through 6. In this case, it represents a flow from left-toright. Reverse the sequence for right-to-left machines. If the dish flow is from left-to-right, the proper sequence for the placement of the curtains would be: long-narrow curtain in the first position; short curtain in the second position; two short-wide curtains in the third position; two short-wide curtains in the fourth position; and a long-narrow curtain in the sixth position. The only curtain change to reverse the flow of dishes is the short curtain at position #2 is changed to position #5.
CMA-66
3 1 2 4 5 6
DISH FLOW
Page 4
Getting Started
2.2.1. Electrical *
A 3-phase 208-240 volt AC, 60 Hz dedicated circuit should be used to supply electrical energy to the CMA-66 dishwasher (see specification sheet page 2). Connect the wire that has the highest voltage (stinger lead) to L-2 on the power block. Power lead wires (L1, L2 and L3) used for the CMA-66 at installation must comply with all local and State electrical codes.
2.2.2. Plumbing*
The water supply connection is made with a hot water line to the water supply inlet on the top of the machine. The water supplied to the machine must be a minimum of 140 F for the CMA66L and a minimum of 180 F for the CMA-66H.
NOTE: The High Temp machine (CMA-66H) comes with two water supply line connections. One
is for the final rinse at 180 F and the other is to fill the machinethis water will be heated to the appropriate temperature by the wash tank heater. (See specification sheet on page 2). There are two 2 drain connections to be made. One connection is made at either end of the horizontal drainpipe coming from the wash tank and the other connection is made at the scrap tray drain. (Instructions for installing the scrap tray assembly are provided in section 2.2.4 Scrap Tray Assembly and Overflow Chute Installation.) One of the ends of the horizontal drainpipe has a cap on it simply move the cap to the other end if its currently on the end needed for the drain connection.
TO SCRAP ACCUMULATOR
PREWASH
WASH/RINSE
DISH FLOW
Figure 2.2.3a
See also installation instructions on new style CMA-66 conveyor (Section 4. Customer Notice) 2. The scrap tray assembly is placed inside the machine for shipping. Follow the instructions provided in section 2.2.4 Scrap Tray Assembly and Overflow Chute Installation to properly attach the scrap tray assembly to the dishmachine. 3. Figure 2.2.3b shows the different settings available on the conveyor cam.
Electrical and plumbing connections must be made by a qualified person who will comply with all available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
Page 5
Getting Started
P/N 13505.10 205 RACKS (CMA-66H)
B A
Figure 2.2.3b
4. On a 3-phase machine the water pump motors are also 3-phase and, depending on which terminal each phase is connected to, the motor can rotate in either direction. Check the direction of rotation by removing the dust cap on the back of the motor. The motors must turn clockwise looking at the shaft from the back of each motor. To change the direction of rotation, switch any two power lead wires at the motor. 5. The machine must be running to set the pressure regulator. While the machine is in the FINAL RINSE CYCLE, adjust the pressure regulator to 20 PSI. See section 3.1.2 Rinse Pressure Regulator for detailed instructions.
Page 6
Getting Started
2.2.4. Scrap Tray Assembly and Overflow Chute Installation
The scrap tray assembly and overflow chute, which came packaged inside the machine, can easily be installed by executing the following steps: Figure 2.2.4 below illustrates the assembly as it would appear for a Left-to-Right machine a Right-toLeft machine would simply be the mirror image. Caution: For proper spacing, the SS flat washer (item 2) must not be located between the head of the trusshead bolt and the inside of the machine.
Figure 2.2.4
ITEM NO. NO. REQD 1 2 3 4 5 7 11 11 1 1 P/N 00905.00 00924.00 00912.00 13511.26 13511.06 13511.16 DESCRIPTION -20 X Trusshead Bolt SS Flat Washer -20 Nylon Lock Nut CMA-66P Overflow Gasket CMA-66P Overflow Chute (L-R) CMA-66P Overflow Chute (R-L) ITEM NO. NO. REQD 6 7 8 9 4 1 1 1 P/N 00906.00 17579.00 01579.10 01579.20 DESCRIPTION -20 X Hex Head Bolt Scrap Trap Holder Scrap Trap Body Molded Scrap Trap Drawer Molded
1. Remove the items from their packing and verify that all the pieces are present. 2. Attach the overflow chute with the five -20 X trusshead bolts, SS Flat Washers, and -20 Nylon Lock Nuts provided. 3. Secure the scrap trap holder to the dishmachine using the four -20 X Hex Head Bolts, SS Flat Washers, and -20 Nylon Lock Nuts provided. 4. Set the scrap trap bodywith the scrap trap drawer insertedinto position on the scrap trap holder. 5. Attach the drain as specified in section 2.2.2 Plumbing.
Page 7
Getting Started
Figure 2.2.5
Installation:
When installing the water pump impeller the Nylon Lock Nut indicated by the arrow in Figure 2.2.5 must be in place to prevent the impeller from spinning off of the shaft and damaging the motor.
Removal:
The Nylon Lock Nut indicated by the arrow in Figure 2.2.5 must be removed before attempting to remove the water pump impeller.
Page 8
Getting Started
2.2.6. Optional Hood Adapter (set of two)
An optional Hood Adapter set (P/N 13901.82) is available. proper installation are given below. The dimensions for
75-"
9-"
Page 9
Getting Started
2.2.7. Optional Freestanding Scrap Trap and Adaptor Kit
The optional Freestanding Scrap Trap (P/N 01560.00) and Adaptor Kit (P/N 13512.00) are available for installations where the space is insufficient to accommodate the standard side-mounted scrap trap or where drain access is easier by locating the scrap trap some distance away from the Dishmachine.
DESCRIPTION 1/4-20 Nylon Lock Nut Scrap Trap Flange Nut Scrap Trap Flange Gasket Scrap Trap Adaptor Flange
DESCRIPTION Overflow Gasket 1/4-20 x 3/4" Hex Head Bolt Scrap Trap Adaptor Scrap Trap, Freestanding
*Not Supplied
Page 10
Getting Started
2.2.8. Optional Auto-Fill
With this function a single press of the AUTO FILL switch fills the machine to the proper level. If your Dishmachine did not come with the Auto-Fill option already installed, an Auto-Fill kit is available. Call (800) 854-6417 and order Kit #13468.00 Kit #13468.00 Includes: ITEM QTY P/N DESCRIPTION
1 2 3* 4 5 6 7 8 9 10 11
To Install:
1 1 1 1 1 1 2 2 2 2 2
00421.89 13418.85 13419.85 13003.61 00705.05 00400.10 00401.10 00907.00 00965.00 00661.00 52000.00
Rocker Switch, Momentary Timer Relay Timer Relay Socket DIN Rail, 3 (with 2-sided tape) Solenoid Valve 1/2" Conduit, 2 feet 1/2" Straight Connector 6-32 x 1/2" Pan Head Screw 6-32 Nylon Lock Nut Wire Nut #250 Piggyback Connector
Warning! Turning the machine off at its power switch is not sufficient, as a shock hazard is still present. Power must be disconnected at the circuit breaker.
1. With the water supply turned off at the source remove the manual fill valve and replace it with the Solenoid Valve *, (P/N 00705.05). 2. Depending on which control cabinet came installed on your machine, there will either be an area of open DIN rail for mounting the pre-wired Timer Relay Socket (P/N 13419.85) or there will be two predrilled holes in the upper-right corner. If there is no open area on the DIN rail but the two holes are present, mount the DIN Rail (P/N 13003.61) inside the control cabinet using the two 6-32 x 1/2" Pan Head Screws (P/N 00907.00) and 6-32 Nylon Lock Nuts (P/N 00965.00). The screws should be inserted through the DIN Rail and out the back of the control cabinet. 3. Secure the pre-wired Timer Relay Socket (P/N 13419.85) to the DIN Rail by snapping it into place. See Figure 1 on the following page for orientation of socket. 4. Remove the blue wire from the Main Contactor coil terminal (see Figure 2 on the following page) and put one of the two #250 Piggyback Connectors (P/N 52000.00) on the coil terminal.
**
Electrical and plumbing connections must be made by a qualified person who will comply with all available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
Page 11
Getting Started
10
11
To coil terminal (blue) of main contactor To coil terminal (red) of main contactor
Blue Red
Figure 1
Control Panel
10
11
Blue Red
Main Contactor
Heater Contactor
+
+
+
+
Figure 2
Top
3
of Cabinet
} To solenoid
Page 12
Getting Started
5. Connect the blue wire you removed from the Main Contactor coil terminal to the #250 Piggyback Connector and connect the blue wire from terminal 10 of the Timer Relay Socket to the same #250 Piggyback Connector on the coil terminal. See Figure 1 and Figure 2 on the previous page. 6. Remove the red wire from the Main Contactor coil terminal (see Figure 2 on the previous page) and put the other #250 Piggyback Connectors (P/N 52000.00) on the coil terminal. 7. Connect the red wire you removed from the Main Contactor coil terminal to the #250 Piggyback Connector and connect the red wire from terminal 11 of the Timer Relay Socket to the same #250 Piggyback Connector on the coil terminal. See Figure 1 and Figure 2 on the previous page. 8. Pop out the rocker switch hole plug from the Auto Fill switch position in the front panel. There are two violet wires attached to it. Pull the two wires off of the hole plug and connect themeither wire to either terminalto the two terminals on the Rocker Switch (P/N 00421.89) from the kit and insert the Rocker Switch into the hole. Position the switch so that it rocks to the right when actuating. 9. The other ends of the two violet wires coming from the Rocker Switch are bundled into the wire harness. Free up the ends for easy access. Connect the two violet wires from terminals 2 and 6 of the Timer Relay Socket to the ends of the two violet wires coming from the Rocker Switch. See Figure 1 on the previous page. 10. Using one of the two 1/2" Straight Connectors (P/N 00401.20) that came with the kit, mount one end of the 1/2", 2 feet Conduit (P/N 00400.10) to a 7/8 hole in the back of the control cabinet. 11. Secure the remaining 1/2" Straight Connector to the other end of the 1/2" Conduit and route the blue/yel wire from terminal 10 of the Timer Relay Socket and the orange wire from terminal 9 of the Timer Relay Socket through the 1/2" Conduit to the Solenoid Valve. 12. Using the two Wire Nuts (P/N 00661.00) connect the blue/yel wire and the orange wire to the two wire leads coming from the solenoideither wire to either wire. Connect the 1/2" Conduit to the Solenoid Valve with the 1/2" Straight Connector. 13. Plug the Timer Relay (P/N 13418.85) into the Timer Relay Socket and check that it is set up as follows: OUT POWER a. Mode selected is D Timer Dial 9 12 b. Scale displayed is 0 18 c. Range selected is 10S 6 15 d. Timer dial is set near 9
0
MODE D
18
RANGE 10S
Mode
idec
Scale 14. Turn on the machine and test your new Auto Fill feature.
GT3A
Range
When Auto Fill is activated (and the rinse pressure is set to 20 PSI), the machine should fill until it begins to overflow into the scrap tray, at which point it should stop filling. If needed, adjust the time setting on the Timer Relay to accomplish this. Users note: If at any time less than a full Auto Fill cycle is desired the Auto-Fill can be interrupted (stopped) by turning off the power to the machine. The machine will resume normal operation upon restoring power without continuing the Auto Fill cycle.
Page 13
Getting Started
one for rinse chemical and one for sanitizer chemical, but only one is needed with the CMA-66Hfor rinse chemical only. 2. Connect only to the primary side of the Listed Class 2 Transformer, 208-230 VAC, 60 Hz, 100 VA maximum load. 2.2.9.2. Hood Fan Motor
TERMINAL BLOCK
FAN CONTACTOR
WIRES FROM THE POWER SOURCE *
L1 T1 L2 T2
* *
Electrical and plumbing connections must be made by a qualified person who will comply with all available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
Page 14
Getting Started
2.3.
DANGER: Always turn off the circuit breaker at the wall when working on this
CAUTION: Do not get in the path of the conveyor rocker arm or the conveyors moving
bar. Do not reach into the rocker arm area without first making sure the dishmachine is turned off at the circuit breaker.
CAUTION: Do not open the front door when the machine is in operation. CAUTION: Avoid spraying water on or around the electrical control box on the top of the
Page 15
Operation
3. Operation
3.1. Initial Setup
When Auto Fill is activated, the machine should fill until it begins to overflow into the scrap tray, at which point it should stop filling. If necessary, adjust the time set on the Auto Fill Timer to allow an appropriate amount of water flow to properly fill the Dishmachine. See Section Error! Reference source not found. Error! Reference source not found. Item 3 (Note: With the Auto Fill option there are two timers in the control box. The Auto Fill Timer is in the upperright corner of the control box). Users note: If at any time less than a full Auto Fill cycle is desired, the Auto-Fill can be interrupted (stopped) by turning off the power to the machine. The machine will resume normal operation upon restoring power without continuing the Auto Fill cycle.
Page 16
Operation
3.2.
Beginning Operation
To run the dishmachine, perform the following steps: 1. Close both drains (valve handles in vertical position).
CLOSE
CLOSE
2. Turn on the power to the dishmachine. 3. Open the fill-valve and fill the machine until it overflows out of the pre-wash tank into the scrap tray or, if the Auto Fill option is present, press the AUTO FILL switch to fill the machine with water. 4. Turn the heater on. The temperature of the water in the tank should be 140F 150F. The Tank heater will maintain a minimum temperature of 140 F if the final rinse is providing 140F 150F at all times (CMA-66L). 150F minimum will be maintained if the final rinse is 180F 195F (CMA66H). If the thermostat (located behind the stainless steel cover on the final rinse side of the machine) should need adjustmentthere is a thermostat adjustment access hole located on the cover.
Tip: If you are having difficulty maintaining wash tank temperature, minimize the vent hood openings by closing off the dampers.
5. Be sure to place the dishes correctly. If they become dislodged, they could interfere with the trip switch lever and interrupt the operation of the machine.
Page 17
Operation
RACK TRAVEL
6. At the end of the shift and after heavy periods of accumulation, clean the three strainer trays inside the machine.
STRAINER TRAY
Also, at the end of each shift, remove and clean the six spray arms. Then reinstall them into the machine.
SPRAY ARM
Also, when water becomes heavily soiled, drain the tanks and refill the machine. 7. Check chemical buckets. Make sure there is an adequate supply of detergent, rinse aid and (CMA-66L only) sanitizer. Also, verify that the pickup line is inserted into the correct bucket. 8. Slide in a dish rack to activate the cycle start trip switch on the pre-wash end of the machine. The 60-second time-delay-off relay will hold the machine in the run mode for 60 seconds after a rack releases the cycle start switch and then shut off. This time-delay relay prevents the machine from continuing to run when a dish rack is not in the machine.
Page 18
Operation
The sanitizing pump operates when the fresh water enters the machine during final rinse. The water is treated at 50 PPM (parts per million). The pressure regulator is adjusted to 20-PSI. This allows 0.8 (CMA-66L), or 0.94 (CMA-66H) gallons of water to enter the machine each time a rack is washed. It is recommended that the 5-1/2% chemical solution be standardized to allow uniform dispensing of the sanitizing solution into the flow of rinse water as the machine operates. At this level, maximum shelf life is available. Inside the control box is a labeled power block for the sanitizer and rinse aid, which is powered when the final rinse trip switch is activated. The detergent power block is also labeled and provides power when the conveyor and pump motors are operational.
3.3.
Page 19
Operation
6. Replace all the strainer trays into their proper position and fill the machine. 7. Place a rack into the machine and observe the spray pattern of the pre-wash, the wash, and the final rinse. a. Check the titration of the wash tank at this point. b. While the rack is in the final rinse, check for 50 PPM residual chlorine in the final rinse. c. Observe the final rinse vacuum breaker for leaks. 8. Run a stemware or glass rack through the machine and check the results on the glassware. a. Observe the check valves for the rinse and sanitizer. Make sure they are not leaking or building up chlorine crystals. If they are clean, leave them alone. b. Check the condition of the chemical tubing from the peri-pump to the check valves. c. Check the peri-pump squeeze tubes to make sure they are tight, pumping product properly and not leaking within the peri-pump. There should be no moisture within the peri-pump itself. d. Observe the final rinse pressure at 20 PSI. Adjust if necessary. 9. Check the condition of the chemical tubing coming from the detergent rinse and sani buckets, up to the machine. 10. With the machine stopped, check the roller cam bearing on the conveyor. You should be able to move the outer cover of that roller cam bearing with your finger. Also, keep it well greased so that the outer covering does not freeze up. 11. Check the conveyor system. Make sure the complete system is running smoothly. 12. Send two or three racks through the machine. Check the scrap overflow. While the racks are running through the machine, look under the machine for any drips or leaks coming from the machine or pump seals. 13. Send a rack through the machine and check if the 60-second off delay is operating properly. If the relay is working properly the machine will shut off approximately 60 seconds after the cycle start trip switch is de-activated. 14. Send a rack through and check if the cycle start trip switch is operating properly. This trip switch is located on the pre-wash end of the machine and is activated by sliding a dish rack into the machine. 15. Using an all-purpose cleaner or stainless steel polish, clean up the outside of the machine to keep it looking nice. 16. Once this is done, fill out a service report and take it to the manager.
MODEL CMA-66 Installation & Operation Manual Rev. 1.06 01/11/05
Page 20
Operation
3.4.
MODELS: CMA 44/66 CONVEYOR (S) TECHNICAL ISSUE Continuously cycles Conveyer timer faulty Faulty tilt micro switch Final rinse does not come on Micro switch cam out of adjustment Faulty rinse solenoid valve Power disrupted Faulty table limit switch Does not run Faulty door reed switch Burnt internal glass fuse Faulty power shut off switch Faulty main contactor Losing water Machine is not level Dishtable slants away from dishmachine, loosing water down quick- drain on table Broken shaft seal in gear box Wrong conveyor motor rotation Replace timer, P/N 13418.85 Replace micro switch, P/N 00411.00 Adjust cam Replace diaphragm or coil, P/N 00738.15 Check wall breaker switch Check and replace, P/N 13827.10 Check and replace, P/N 00557.30 Check and replace, P/N 13403.26 Check and replace, P/N 00421.83 Check and replace, P/N 13003.50 Level machine using leg adjustments Slant table to carry excess water towards machine tank/plumb quick-drain back to machine above water line Replace gear box, P/N 13504.00 OR .12 Replace bearing, check and correct conveyor motor rotation, P/N 13507.50 Check and replace, P/N 13418.85 Check and replace, P/N 13003.70 Check and replace, P/N 00421.87 Check and replace, P/N 13417.85 Check and replace, P/N 13463.10 Check and replace, P/N 13003.50 Check and replace, P/N 13417.77 Adjust (20psi) or replace regulator, P/N 13602.45 Clean rinse arm jets Check and replace solenoid, P/N 00738.15 Check and clean Check and clean CAUSE SOLUTION Manual/auto switch in MANUAL mode or faulty Turn switch to AUTO position or replace
Faulty reed switch at the dishmacine entrance Check and replace, P/N 00557.56 Machine only runs in manual mode Faulty conveyor timer Faulty manual/auto toggle switch Faulty heater switch Faulty heater thermostat Heater does not work Faulty heater float switch Faulty heater contactor Faulty heater Not adjusted or faulty pressure regulator Low or no pressure at final rinse arm Clogged rinse arm jets Faulty water solenoid Clogged manifold system No pressure at wash arms Clogged spray jets
Motor rotation, wrong direction See wiring instruction on motor for proper rotation Debris stuck in pump cover/damaged impeller Check and clean/replace impeller, P/N 03222.85
Page 21
Operation
3.5.
Trouble Shooting
LIKELY CAUSE
Bad motor or capacitor Faulty contactor Fuse is burned out Table limit switch Defective door reed switch Defective start reed switch Defective auto/manual switch Defective 60 Sec. Timer
SOLUTION
Replace defective motor Replace contactor Replace fuse Remove dish rack at switch Replace reed switch Replace reed switch Replace switch Replace timer Replace timer or change settings Replace contactor Check movement-replace it Replace thermostat or adjust Replace heater contactor Replace heater Replace switch Check and correct Replace rack Adjust properly Check hot water supply Adjust thermostat Close vents as much as possible Replace heater Remove and clean Adjust pressure regulator Replace or clean Remove and clean jets Replace reed switch Check dispenser troubleshooting guide Set 20 psi. Plumb quick drain back into pre-wash tank above water line Use CMA sheet pan rack Close completely Check rinse pressure, drain valve open Clean jets Connect motors to reverse impeller direction
Defective 60 Sec. Timer or settings Contactor stuck Float switch Defective thermostat or setting Defective heater contactor Defective heater Defective heater switch Wire connections
Broken rack Tray track alignment Low incoming water supply (150F-low temp, 180 F- high temp) Thermostat setting Vent hoods Defective heater Plugged rinse jets
Pressure regulator out of adjustment Water sol. valve coil or diaphragm Dirty rinse jets Defective rinse reed switch
Dispenser or settings Rinse pressure Quick drain on pre-wash end Sheet pans Drain valves open
Page 22
Page 23
Operation
Trip switch blocked or held from free movement due to a lodged utensil or dish. Lines to chemical buckets found in wrong containers or empty. (Lines to the buckets are color-coded.)
Lessees service responsibility shall be limited to its initial orientation, delivery of chemicals, adjustment of chemical injection system, and replacement of parts found to be worn or defective.
Page 24
3 AMP SLOW BLOW FUSE (x2) 220V SIGNAL FOR USER SUPPLIED FAN MOTOR CONTROL CONTACTOR COIL.
T3
T2
T1
A1 A 1 A1
L1 L2 L3
A 1
START
L1
L2 L1
L3 L2
L3
L1
L2
L3
MAIN CONTACTOR
PUMP CONTACTOR PUMP CONTACTOR
SEC
POWER 100-240VAC
HEATER CONTACTOR
PUMP CONTACTOR
T1 T2 T3 T1 T2 T3
conveyor contactor
A2 A2
T1 T1 T2 T3
T2
T3 T1
T2
T3
L3
L2
L1
A2 A2
11
10
2 RINSE
}
OVERLOAD RELAY
T1 T2 T3
GROUND
95
5. Electrical Diagram
FLOAT SWITCH
PUMP MOTOR CONV MOTOR PUMP MOTOR PUMP MOTOR
ADJ. THERMOSTAT
11
10
POWER SWITCH
HEATER SWITCH
NOTES:
1: REMOVE JUMPER FOR OPTIONAL TABLE LIMIT SWITCH CONNECTION. 2: SANI/RINSE. POWER IS ON WHEN FINAL RINSE IS ACTIVE. 3: CONNECT ONLY TO PRIMARY OF LISTED CLASS 2 TRANSFORMER 208-230V 60Hz MAXIMUM 100VA. 4: DETERGENT FEEDER CONNECTIONS AND SIGNAL FOR FAN MOTOR CONTROL CONTACTOR COIL. 5: PRESENT ONLY WITH AUTO-FILL OPTION. AUTO MANUAL
Operation
(NOTE 5)
Page 25