Professional Documents
Culture Documents
Discussion of "Distribution of Residual Load and True Shaft Resistance For A Driven Instrumented Test Pile "
Discussion of "Distribution of Residual Load and True Shaft Resistance For A Driven Instrumented Test Pile "
DISCUSSION / DISCUSSION
Discussion of Distribution of residual load and true shaft resistance for a driven instrumented test pile1
Carlos Lam and Stephan A. Jefferis
Introduction
The authors have presented a well-documented case study of the load test interpretation of prestressed high-strength concrete (PHC) piles, which are very popular in the Far East and are often favoured over steel piles on the basis of cost. Despite their popularity, well-analyzed load test case histories are rare and hence the authors paper is a valuable contribution to the technical knowledge base. Although the authors have considered the geotechnical aspects in detail, the discussers believe that this case study also would benefit from a fuller analysis of the structural conditions of the piles. This is because the authors have identified that the key design aspects for this site are actually the maximum load in the pile and the pile structural strength, but not the pile capacity. Based on the load test results, the authors concluded that the long-term maximum load in the pile will approach the pile structural strength and hence grouting the central void should be considered. The discussers have carried out an assessment of the pile strength using a different approach and compared the results with the current design guidelines. It was found that even with the central void grouted, the PHC piles are still not sufficiently robust and a different pile size or type may need to be considered. The discussers assessment and, where appropriate, comparisons with the authors results are described as follows.
ulus and strain values. For example, the authors reported that the back-calculated secant modulus of the pile (Es) can be expressed as 29.00.003 m3 for the Myeongji pile. If a moderate strain level of, say, 800 m3 is substituted into this equation, then the pile modulus will be 26.6 GPa. If this value is used instead, then the calculated pile strength will be 11% lower than the given estimated value. The strain level used is also subject to debate, as in reinforced concrete design the concrete is commonly assumed to crush at a strain level of about 0.2% (see, e.g., Wight and MacGregor 2009). If this value is used, the calculated pile strength will increase by more than 30% to well over the observed ultimate strength. As noted by the authors, the pile design for this site is governed by the structural strength of the pile. A more detailed analysis therefore seems necessary. The discussers have carried out an assessment of the ultimate strength of the PHC piles using the conventional prestressed concrete design method. The equations used are given in Gilbert and Mickleborough (1990). In essence, for a prestressed concrete member subject to pure compression, the ultimate strength can be expressed by the following equation: 1 Nu Cc T p where Nu is the ultimate strength, Cc is the compressive force in the concrete, and Tp is the tension in the prestressed steel. The first term, Cc, is given by 2
0 Cc 0:85fcyl Ac 0 where fcyl is the compressive cylinder strength of concrete 0 ) and Ac is the cross-sectional area of concrete. The ( 0.8 fcu factor 0.85 accounts for the difference between the actual and idealized stress block, and the strength difference between the cylinder specimen and the actual member. The second term, Tp, is given by
Tp 3pu Ep Ap
Received 11 October 2011. Accepted 8 November 2011. Published at www.nrcresearchpress.com/cgj on 26 January 2012. C. Lam. Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire, OX1 3PJ, UK. S.A. Jefferis. Environmental Geotechnics Ltd., St Marys Grove, 4 Adderbury Park, Adderbury, Banbury, Oxfordshire, OX17 3EN, UK; Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire, OX1 3PJ, UK. Corresponding author: Carlos Lam (e-mail: [email protected] and [email protected]).
1Appears
245
where 3pu is the strain in the prestressed steel at ultimate, Ep is the elastic modulus of the prestressed steel, and Ap is the cross-sectional area of the prestressed steel. The values of these parameters have been given by the authors except for 3pu, which needs to be calculated using the effective prestress (fpe), which is 8 MPa for the piles concerned. Using eqs. [1] to [3], the ultimate strength, Nu, is estimated to be 6.9 MN for the ungrouted Myeongji pile and 9.2 MN for the grouted Shinho pile. For the estimation of the latter, eq. [1] was extended to include the strength contribution of the grout, Cg (= 0.85 fg0 Ag). The authors state that the grout was of strength 18 MPa, but do not say whether this was a cube or cylinder strength. The discussers have assumed it to be a cube strength and thus the equivalent cylinder strength could be about 80% of 18 MPa. However, the in-pile strength of the grout will be increased as it is confined and the overall effect may be that the actual strength of the grout in the pile was about 18 MPa. Therefore, for the calculations of Cg, the discussers have taken fg0 as 18 MPa. It can be seen that by using this approach the calculated Nu for the ungrouted Myeongji pile (6.9 MN) is similar to the actual observed value of 6.4 MN and is not far from the authors value of 6.0 MN. The discussers overestimation (8% of true value) is probably due to the fact that the Myeongji pile has a hollow core, but the above calculations do not take into account the effect of reduced internal confinement (see, e.g., Dilger et al. 1996 for experimental evidence of the hollow core effect). Unlike the case of the Myeongji pile, the calculated Nu for the grouted Shinho pile (9.2 MN) is considerably lower than the authors prediction of 12.0 MN. If the discussers prediction is correct, then it would appear that the maximum test load applied to the Shinho pile ( 9.0 MN) was already very close to its ultimate strength. As the Shinho pile was not loaded to structural failure, the actual ultimate strength is not known.
As can be seen, both equations take into account the effect of effective prestress and limit the compressive stress in the concrete to below a certain level. If these equations are used, then the allowable load for the ungrouted pile will be 2.6 MN (eq. [4]) and 2.5 MN (eq. [5]). By assuming strain compatibility and taking force equilibrium into account, for the same concrete stress level (N/Ac), the allowable load for the grouted pile has been estimated to be about 4.5 MN. It can be seen that this value is just above the maximum load of 4.3 MN for the Myeongji site, but is considerably lower than the maximum load of 6.0 MN for the Shinho site.
Conclusions
Based on an assessment of the structural strength of the PHC piles, it appears that even with the central void grouted the piles are still not sufficiently robust for the Shinho site if the maximum pile load is to be kept below the allowable load as required by the North American or British design standards. To tackle this problem, it may be necessary to consider using a grout with a higher compressive strength (>18 MPa) and probably also steel reinforcement in the grout. If these measures are not sufficient, a different pile size or type may have to be considered.
References
BSI. 1986. Code of practice for foundations. British standard BS 8004:1986. British Standards Institution, London. Dilger, W.H., Ghali, A., and Krishna Mohan Rao, S.V. 1996. Improving the durability and performance of spun-cast concrete poles. PCI Journal, 41(2): 6890. Gerwick, B.C., Jr. 1993. Construction of prestressed concrete structures. 2nd ed. John Wiley & Sons, Inc., New York. Gilbert, R.I., and Mickleborough, N.C. 1990. Design of prestressed concrete. Spon Press, London. Hannigan, P.J., Goble, G.G., Likins, G.E., and Rausche, F. 2006. Design and construction of driven pile foundations. Vol. I. FHA Publication No. FHWA NHI-05-042. Federal Highway Administration (FHA), U.S. Department of Transportation, Washington, D.C. PCI Committee on Prestressed Concrete Piling. 1993. Recommended practice for design, manufacture and installation of prestressed concrete piling. PCI Journal, 38(2): 1441. Wight, J.K., and MacGregor, J.G. 2009. Reinforced concrete: mechanics and design. 5th ed. Pearson Prentice Hall, Upper Saddle River, N.J.
List of symbols
A C c E cross-sectional area compressive force subscript meaning concrete elastic modulus compressive cube strength of concrete compressive cylinder strength of concrete compressive cube strength of grout effective (net) prestress subscript meaning grout allowable axial strength of pile ultimate axial strength of pile subscript meaning prestressed steel subscript meaning secant tension strain in the prestressed steel at ultimate
whereas in the UK and in some Commonwealth countries, the following equation is used instead (BSI 1986): 5
0 N 0:25fcu fpe Ac