r050212306 Transport Phenomena in Bioprocess
r050212306 Transport Phenomena in Bioprocess
1
II B.Tech I Semester Supplementary Examinations, February 2007
TRANSPORT PHENOMENA IN BIOPROCESS
(Bio-Technology)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
2. Write the expression to calculate maximum cell concentration. Define each term in
the above equation and write the units. [16]
3. (a) How does the power input to agitator influence the interfacial area.
(b) Describe the influence of temperature and pressure on the oxygen transfer rate
in fermentation broths. [6+10]
4. Discuss the variation of Power number with Reynolds number for laminar, turbulent
and transition region for ungassed fluids. [16]
7. Calculate the heat loss per meter square of surface area for an insulating wall
composed of 25.4mm thick fiber insulating board, where the inside temperature
is 352.70 and the outside temperature is 297.10 k. Thermal conductivity of fiber
insulating board is 0.048 w/m0 k . [16]
8. Ethylene glycol is to be heated from 200C to 540 Cin a tube having 50mm inside
diameter. The tube wall is maintained at a constant temperature of 85 0 C. The
flow velocity through the tube is 2 m/s. Density is 1104 kg /m3 ; specific heat is
2460 J/kg 0 K; viscosity is 0.0107N-s/ m2 ; thermal conductivity is 0.255w/m 0 K;
viscosity at wall temperature is 0.0029 N-s / m2 . Calculate the length of the heat
exchanger tube. [16]
⋆⋆⋆⋆⋆
1 of 1
Code No: R050212306 Set No. 2
II B.Tech I Semester Supplementary Examinations, February 2007
TRANSPORT PHENOMENA IN BIOPROCESS
(Bio-Technology)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
2. Why gas liquid mass transfer is important in bio processing. Explain with examples.
[16]
4. (a) Write the expression for the ratio of gassed to un gassed power as a function
of operating conditions.
(b) Define impeller Reynolds number and power number for Newtonian fluids.
[8+8]
5. Discuss the phenomena of boundary layer separation and wake formation [16]
7. (a) Write briefly on individual heat transfer coefficient and overall heat transfer
coefficient
(b) Draw the temperature profile for heat transfer with fouling deposits on both
surfaces. [10+6]
8. A single pass shell and tube heat exchanger is used to heat a dilute salt solution
used in large scale protein chromatograph. 25.5 m3 /hr solution passes through
42 parallel tubes inside the heat exchanger; the internal diameter of the tubes is
105cm and the tube length is 4m. The viscosity of bulk salt solution is 10−3 kg/ms
and the density is kg/m3 , the average heat capacity is 4 kJ/kg0 C and the thermal
conductivity is 0.64 w/m 0 C. Calculate the heat transfer coefficient. [16]
⋆⋆⋆⋆⋆
1 of 1
Code No: R050212306 Set No. 3
II B.Tech I Semester Supplementary Examinations, February 2007
TRANSPORT PHENOMENA IN BIOPROCESS
(Bio-Technology)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
2. Explain with a neat sketch the oxygen transfer methodology from gas to liquid bulk
to active site in the cell cluster. [16]
3. How are the agitators used to improve the mass transfer rate are classified. What
type of agitators are used for better gas liquid contact, viscous liquids and slurries,
semi solid masses. [16]
4. Describe the procedure to estimate the power requirements for ungassed non New-
tonian fluids. [16]
7. (a) Write the units of thermal conductivity and heat transfer coefficient
(b) Write the equation to calculate conductive heat flux.
(c) Write the equation to calculate convective heat flux .
(d) Write the equation to calculate heat flux by conduction through a series of
plane walls. [4+4+4+4]
8. A fermenter used for antibiotic production must be kept at 270 C. The maximum
heat transfer rate required is estimated as 550kw. Cooling water is available at
10 0 C. The exit temperature of the cooling water is 25 0 C. The heat transfer
coefficient of the fermenter broth is given as 2150 w/m2 0 C. The heat transfer
coefficient for the cooling water is calculated as 14000 w/m2 0 C. It is proposed to
install a helical coil inside the fermenter; the outer diameter of the coil pipe is 8cm;
1 of 2
Code No: R050212306 Set No. 3
the pipe thickness is 5mm and the thermal conductivity os the steel is 60 w/m 0 C.
An average internal fouling factor of 8500 w/m2 0 C is expected; the fermenter side
surface of the coil is kept relatively clean. What length of cooling coil is required.
[16]
⋆⋆⋆⋆⋆
2 of 2
Code No: R050212306 Set No. 4
II B.Tech I Semester Supplementary Examinations, February 2007
TRANSPORT PHENOMENA IN BIOPROCESS
(Bio-Technology)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. What are the various theories of diffusion mass transfer. Explain. [16]
2. (a) Mention the different phases between which the mass transfer takes place.
(b) Write the equation to determine the liquid mass transfer flux.
(c) Write the equation to determine the mass transfer flux through gas film.
(d) Write the units of concentration. [4+5+5+2]
3. (a) Write the equation to calculate mass transfer coefficient using static method
and explain each term.
(b) Write the equation to determine mass transfer coefficient by dynamic gassing
out method and explain each term. [8+8]
4. Discuss the parameters on which the mixing power for non aerated fluids depend.
[16]
7. Calculate the heat loss per meter square of surface area for an insulating wall
composed of 25.4mm thick fiber insulating board, where the inside temperature
is 352.70 and the outside temperature is 297.10 k. Thermal conductivity of fiber
insulating board is 0.048 w/m0 k . [16]
8. (a) Draw a neat labeled sketch of single pass shell and tube heat exchanger.
(b) Draw the curves for temperature changed for counter current flow in a double
pipe heat exchanger. [10+6]
⋆⋆⋆⋆⋆
1 of 1